Since commit e085b51c74 ("mmc: meson-gx: check for scatterlist size alignment in block mode"),
support for SDIO SD_IO_RW_EXTENDED transferts are properly filtered but some driver
like brcmfmac still gives a block sg buffer size not aligned with SDIO block,
triggerring a WARN_ONCE() with scary stacktrace even if the transfer works fine
but with possible degraded performances.
Simply replace with dev_warn_once() to inform user this should be fixed to avoid
degraded performance.
This should be ultimately fixed in brcmfmac, but since it's only a performance issue
the warning should be removed.
Fixes: e085b51c74 ("mmc: meson-gx: check for scatterlist size alignment in block mode")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210416094347.2015896-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
.set_ios() is called from .resume() as well. For SDIO device which sets
keep-power-in-suspend, nothing should be changed after resuming, as well
as sample tuning value, since this value is tuned already. So we should
not overwrite it with the default value.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/1618539454-182170-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver data (struct sdhci_s3c_drv_data) stored in of_device_id
table is allocated as const and used only in const-way. Skip
unnecessary const-away casts and convert all users to work with pointer
to const. This is both more logical and safer.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210415084412.51125-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Correct the name of sdhci_s3c_drv_data structure in kerneldoc:
drivers/mmc/host/sdhci-s3c.c:143: warning:
expecting prototype for struct sdhci_s3c_driver_data. Prototype was for struct sdhci_s3c_drv_data instead
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210415084412.51125-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use of_device_get_match_data() to make the code slightly smaller and to
remove the of_device_id table forward declaration.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210415084412.51125-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, only SDHI on R-Car Gen2+ reinitializes the irq register
during reset but it should be done on all instances. We can move it from
the SDHI driver to the TMIO core, because we now have the
'sd_irq_mask_all' variable which carries the proper value to use. That
also means we can remove the initialization from tmio_mmc_probe()
because it calls tmio_mmc_reset(), too. We only move that
tmio_mmc_reset() call there a little to ensure 'sd_irq_mask_all' is
properly set.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210413083137.11171-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GL975x enters ASPM L1 state after a short idle in default.
Enlarge the idle period to 7.9us for improving the R/W performance.
Signed-off-by: Ben Chuang <benchuanggli@gmail.com>
Link: https://lore.kernel.org/r/20210415032637.5219-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull OPP (Operating Performance Points) framework updates for v5.13
from Viresh Kumar:
"This adds devm variants for OPP APIs and updates few of the users
as well (Yangtao Li and Dmitry Osipenko)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
memory: samsung: exynos5422-dmc: Convert to use resource-managed OPP API
drm/panfrost: Convert to use resource-managed OPP API
drm/lima: Convert to use resource-managed OPP API
mmc: sdhci-msm: Convert to use resource-managed OPP API
spi: spi-qcom-qspi: Convert to use resource-managed OPP API
spi: spi-geni-qcom: Convert to use resource-managed OPP API
serial: qcom_geni_serial: Convert to use resource-managed OPP API
opp: Change return type of devm_pm_opp_attach_genpd()
opp: Change return type of devm_pm_opp_register_set_opp_helper()
opp: Add devres wrapper for dev_pm_opp_of_add_table
opp: Add devres wrapper for dev_pm_opp_set_supported_hw
opp: Add devres wrapper for dev_pm_opp_set_regulators
opp: Add devres wrapper for dev_pm_opp_set_clkname
devm_ioremap_resource() has recorded error log, so it's
unnecessary to record log again.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Laibin Qiu <qiulaibin@huawei.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210409023801.3326572-1-qiulaibin@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_ioremap_resource() has recorded error log, so it's
unnecessary to record log again.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jia Yang <jiayang5@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210409015424.3277212-1-jiayang5@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_ioremap_resource() has recorded error log, so it's
unnecessary to record log again.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Laibin Qiu <qiulaibin@huawei.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20210409023349.3325907-1-qiulaibin@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that we got the timeout handling in the driver correct, we can use
this capability to avoid polling via the MMC core.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210409094606.4317-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD8 is not supported with Command Queue Enabled. Add required callback
to clear CQE_EN and CQE_INTR fields in the host controller register
before sending CMD8. Add corresponding callback in the CQHCI resume path
to re-enable CQE_EN and CQE_INTR fields.
Reported-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Aniruddha Tvs Rao <anrao@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210407094617.770495-1-jonathanh@nvidia.com
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For GL9763E, although there is the best performance at the maximum delay.
Change the value to 20us in order to have better power consumption.
This change may reduce the maximum performance by 10%.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20210407093816.8863-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes the following W=1 kernel build warning(s):
drivers/mmc/host/moxart-mmc.c:257:7: warning: variable ‘dma_time’ set
but not used
drivers/mmc/host/moxart-mmc.c:395:7: warning: variable ‘pio_time’ set
but not used
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1617357231-93064-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bus power may control card power, but the full reset done by SDHCI at
initialization still may not reset the power, whereas a direct write to
SDHCI_POWER_CONTROL can. That might be needed to initialize correctly, if
the card was left powered on previously.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210331081752.23621-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As indicated by function esdhc_change_pinstate(), SDR50 and DDR50
require pins_100mhz, while SDR104 and HS400 require pins_200mhz. Some
system design may support SDR50 and DDR50 with 100mhz pin state only
(without 200mhz one). Currently the combined 100/200 MHz pinctrl state
check prevents such system from running SDR50 and DDR50. Separate the
check to support such system design.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20210326110214.28416-1-shawnguo@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the CQHCI_QUIRK_SHORT_TXFR_DESC_SZ quirk because the
latest chips have this fixed and earlier chips have other
CQE problems that prevent the feature from being enabled.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210325192834.42955-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As pointed out by Ulf, "both "mmc->parent" and mmc_dev(mmc) are being
used in the entire c-file". Convert all the mmc->parent usage in all
sdhci host driver to mmc_dev() for consistency.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20210324155013.1e5faa3c@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: c2c4da37837e ("mmc: sdhci-of-dwcmshc: add rockchip platform support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210323112956.1016884-1-weiyongjun1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit adds ACPI support in the sdhci-of-dwcmshc driver for
BlueField-3 SoC. It has changes to only use the clock hierarchy
for Deviec Tree since the clk is not supported by ACPI. Instead,
ACPI can define 'clock-frequency' which is parsed by existing
sdhci_get_property(). This clock value will be returned in function
dwcmshc_get_max_clock().
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Link: https://lore.kernel.org/r/1616453211-275165-1-git-send-email-limings@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After reset, we manually flagged retune in runtime resume, but missed it
in the workqueue. To fix that and avoid the problem in the future, let's
flag retune in the reset handler directly whenever a card is present.
Reported-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210316085717.7276-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Resetting the IP core will lose the bus width information and not all
code paths recover it. So, make sure the latest bus width gets restored
in the reset routine. For that, tmio_mmc_set_bus_width() is moved, but
not modified.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: reworded commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210316085717.7276-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This variant is present on a Lenovo IdeaPad Slim 1, which uses an AMD Dali/Athlon Silver 3050e.
The Windows AMD SD Host Controller driver also lists this as a valid device ID.
Adding this device ID makes the internal eMMC storage on the Lenovo accessible.
Consequently this makes Linux installable and usable on it as well.
Signed-off-by: James Young <james@pocketfluff.org>
Link: https://lore.kernel.org/r/20210318124025.3002861-1-james@pocketfluff.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All recent SDHI instances can be reset via the reset controller. If one
is found, use it instead of the open coded reset. This is to get a
future-proof sane reset state.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210317091622.31890-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
renesas_sdhi_reset used to mainly reset the SCC but is now doing more
and even more will be added. So, factor out SCC reset to have a clear
distinction when we want to reset either SCC or SDHI+SCC.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210317091622.31890-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will soon allow resetting the whole IP core via a reset controller.
For this case, DMA must be terminated before the actual reset. For the
other cases, it is probably better, too.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210317091622.31890-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The retrieval of driver data can be a bit simplified by using
device_get_match_data(), so switch to it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210314230824.148969-2-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
i.MX has been converted to a devicetree only platform, so remove
the non-DT stub for sdhci_esdhc_imx_probe_dt().
Also, make the driver depend on OF now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210314230824.148969-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the following coccicheck warning:
./drivers/mmc/host/via-sdmmc.c:1274:5-8: Unneeded variable: "ret".
Return "0" on line 1295
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1615272478-52458-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20210305090724.18832-1-p.zabel@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20210305090827.19124-1-p.zabel@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Populate the new member for custom mask values to make sure this value
is applied whenever needed. Also, rename the define holding the value
because this is not only about initialization anymore.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210304092903.8534-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For data read commands, SDHC may initiate data transfers even before it
completely process the command response. In case command itself fails,
driver un-maps the memory associated with data transfer but this memory
can still be accessed by SDHC for the already initiated data transfer.
This scenario can lead to un-mapped memory access error.
To avoid this scenario, reset SDHC (when command fails) prior to
un-mapping memory. Resetting SDHC ensures that all in-flight data
transfers are either aborted or completed. So we don't run into this
scenario.
Swap the reset, un-map steps sequence in sdhci_request_done().
Suggested-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Pradeep P V K <pragalla@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1614760331-43499-1-git-send-email-pragalla@qti.qualcomm.com
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's odd to adopt different error handling on failure of
pci_read_config_dword(). Check the return value and terminate
execution flow on failure of all pci_read_config_dword() calls
in this function.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20210226084146.29095-1-dinghao.liu@zju.edu.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Short circuit protection mechanism of GL9755 is disabled by HW default
setting. Enable short circuit protection to prevent GL9755 from being
damaged by short circuit or over current.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Link: https://lore.kernel.org/r/20210225111307.62975-1-reniuschengl@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When imx_data->pinctrl is not a valid pointer, pinctrl_lookup_state
will trigger kernel panic.
When we boot Dual OS on Jailhouse hypervisor, we let the 1st Linux to
configure pinmux ready for the 2nd OS, so the 2nd OS not have pinctrl
settings.
Similar to this commit b62eee9f80 ("mmc: sdhci-esdhc-imx: no fail when no pinctrl available").
Reviewed-by: Bough Chen <haobo.chen@nxp.com>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1614222604-27066-6-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHI Gen2+ has a different value for TMIO_MASK_ALL, so add a member to
support that. If the member is not used, the previous default value is
applied.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210223100830.25125-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A 'tmio_mmc_host_free()' call is missing in the remove function, in order
to balance a 'tmio_mmc_host_alloc()' call in the probe.
This is done in the error handling path of the probe, but not in the remove
function.
Add the missing call.
Fixes: 3fd784f745 ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210220142953.918608-1-christophe.jaillet@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A 'uniphier_sd_clk_enable()' call should be balanced by a corresponding
'uniphier_sd_clk_disable()' call.
This is done in the remove function, but not in the error handling path of
the probe.
Add the missing call.
Fixes: 3fd784f745 ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210220142935.918554-1-christophe.jaillet@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
RPM handling has been improved twice since this comment, and also SCC
handling has been improved a lot. All the testing we did (Geert's and
Niklas' and Wolfram's board farms) with the workaround removed did not
lead to problems, so it is time to get rid of it to the best of our
knowledge.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210218110224.6910-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ->card_event callback isn't being used by any of the dw_mmc variants.
It's likely a leftover from an earlier change, hence let's just drop the
redundant call to it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use resource-managed OPP API to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
An issue has been observed on STM32MP157C-EV1 board, with an erase command
with secure erase argument, ending up waiting for ~4 hours before timeout.
The requested busy timeout from the mmc core ends up with 14784000ms (~4
hours), but the supported host->max_busy_timeout is 86767ms, which leads to
that the core switch to use an R1 response in favor of the R1B and polls
for busy with the host->card_busy() ops. In this case the polling doesn't
work as expected, as we never detects that the card stops signaling busy,
which leads to the following message:
mmc1: Card stuck being busy! __mmc_poll_for_busy
The problem boils done to that the stm32 variants can't use R1 responses in
favor of R1B responses, as it leads to an internal state machine in the
controller to get stuck. To continue to process requests, it would need to
be reset.
To fix this problem, let's set MMC_CAP_NEED_RSP_BUSY for the stm32 variant,
which prevent the mmc core from switching to R1 responses. Additionally,
let's cap the cmd->busy_timeout to the host->max_busy_timeout, thus rely on
86767ms to be sufficient (~66 seconds was need for this test case).
Fixes: 94fe2580a2 ("mmc: core: Enable erase/discard/trim support for all mmc hosts")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20210225145454.12780-1-yann.gautier@foss.st.com
Cc: stable@vger.kernel.org
[Ulf: Simplified the code and extended the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull swiotlb updates from Konrad Rzeszutek Wilk:
"Two memory encryption related patches (SWIOTLB is enabled by default
for AMD-SEV):
- Add support for alignment so that NVME can properly work
- Keep track of requested DMA buffers length, as underlaying hardware
devices can trip SWIOTLB to bounce too much and crash the kernel
And a tiny fix to use proper APIs in drivers"
* 'stable/for-linus-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: Validate bounce size in the sync/unmap path
nvme-pci: set min_align_mask
swiotlb: respect min_align_mask
swiotlb: don't modify orig_addr in swiotlb_tbl_sync_single
swiotlb: refactor swiotlb_tbl_map_single
swiotlb: clean up swiotlb_tbl_unmap_single
swiotlb: factor out a nr_slots helper
swiotlb: factor out an io_tlb_offset helper
swiotlb: add a IO_TLB_SIZE define
driver core: add a min_align_mask field to struct device_dma_parameters
sdhci: stop poking into swiotlb internals
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEuNNh8scc2k/wOAE+9OeQG+StrGQFAmAzrfYACgkQ9OeQG+St
rGTmRQ/+MG9BO1WahlXZ9eVx6n6KmtwlzAy5m4B24GomvcXsa+T2s0Vs43hAsOQ2
f/b6n1mPlwRjAvKW8IfO243HKDE6STGbtVPae6ts586QCODs8i3MQsq4SWmM/DMk
TR87hTo1zd4baVT9tkM8/UdUwQjr0yRf4ZDhcCj09tMClnV/8ZAEE9/lLkBpDoer
wcuPaDtRfJhN+Pqnm8ES8KPj15nVm/GFWBFoDWZIOCjyDnl8Y/1Bnz3NeqzfwM1o
O0NS/9a1tMBn7TNGkkcJCimqOLZS2OgxLND8fie0rC5fmwzVomKXE24OdXpSQCps
LiGJr+iQOaX6qNqJY2h1If8F+RPwKfh4Mrk12x0MWB6Ap2iKsQ6bmtUCNatmJ4PG
5iKV5zY0SwKRYXAkXcNosEPUJqZirFHJCzrQ8IBmiSJ1cahZykWFgorDnA97kNLR
Wlp2Y/037ug7EGZ0YSaXvbpuMyyjDP4TBKqBiSl7a90QYoXQg2QgcrBO3kVlh/5H
Dxq9URvIpDLIGo1EUBU90kB54TUeDhJVHJWDfXNwOp4dP1Xm6b2w+d86GnUQanlC
sinRut1ULMyitmIzg9F74MZKaSJ65ffEP3nZKIAlSSISQL+/bXtMDVtakVGsv1k1
w4IdACf3GqbjHig4mOX0oW7IwtyfBY+0q3udY28ASW0ujsH9qHE=
=BULT
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled
ARM: 9055/1: mailbox: arm_mhuv2: make remove callback return void
amba: Make use of bus_type functions
amba: Make the remove callback return void
vfio: platform: simplify device removal
amba: reorder functions
amba: Fix resource leak for drivers without .remove
ARM: 9054/1: arch/arm/mm/mmu.c: Remove duplicate header
ARM: 9053/1: arm/mm/ptdump:Add address markers for KASAN regions
ARM: 9051/1: vdso: remove unneded extra-y addition
ARM: 9050/1: Kconfig: Select ARCH_HAVE_NMI_SAFE_CMPXCHG where possible
ARM: 9049/1: locomo: make locomo bus's remove callback return void
ARM: 9048/1: sa1111: make sa1111 bus's remove callback return void
ARM: 9047/1: smp: remove unused variable
ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores
ARM: 9045/1: uncompress: Validate start of physical memory against passed DTB
ARM: 9042/1: debug: no uncompress debugging while semihosting
ARM: 9041/1: sti LL_UART: add STiH418 SBC UART0 support
ARM: 9040/1: use DEBUG_UART_PHYS and DEBUG_UART_VIRT for sti LL_UART
ARM: 9039/1: assembler: generalize byte swapping macro into rev_l
Use the proper API to query the max mapping size instead of guessing
it based on swiotlb internals.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/20210208134551.39696-1-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-10-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-9-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-8-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-7-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-6-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-5-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-4-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-3-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204151847.91353-2-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Add support for testing whether bus voltage level translator is present
and operational. This is useful on systems where the bus voltage level
translator is optional, as the translator can be auto-detected by the
driver and the feedback clock functionality can be disabled if it is
not present.
This requires additional pinmux state, "init", where the CMD, CK, CKIN
lines are not configured, so they can be claimed as GPIOs early on in
probe(). The translator test sets CMD high to avoid interfering with a
card, and then verifies whether signal set on CK is detected on CKIN.
If the signal is detected, translator is present, otherwise the CKIN
feedback clock are disabled.
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210124170258.32862-2-marex@denx.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for Qualcomm Inline Crypto Engine (ICE) to sdhci-msm.
The standard-compliant parts, such as querying the crypto capabilities
and enabling crypto for individual MMC requests, are already handled by
cqhci-crypto.c, which itself is wired into the blk-crypto framework.
However, ICE requires vendor-specific init, enable, and resume logic,
and it requires that keys be programmed and evicted by vendor-specific
SMC calls. Make the sdhci-msm driver handle these details.
This is heavily inspired by the similar changes made for UFS, since the
UFS and eMMC ICE instances are very similar. See commit df4ec2fa7a
("scsi: ufs-qcom: Add Inline Crypto Engine support").
I tested this on a Sony Xperia 10, which uses the Snapdragon 630 SoC,
which has basic upstream support. Mainly, I used android-xfstests
(https://github.com/tytso/xfstests-bld/blob/master/Documentation/android-xfstests.md)
to run the ext4 and f2fs encryption tests in a Debian chroot:
android-xfstests -c ext4,f2fs -g encrypt -m inlinecrypt
These tests included tests which verify that the on-disk ciphertext is
identical to that produced by a software implementation. I also
verified that ICE was actually being used.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Satya Tangirala <satyat@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210126001456.382989-9-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Snapdragon SoCs, the Linux kernel isn't permitted to directly access
the standard CQHCI crypto configuration registers. Instead, programming
and evicting keys must be done through vendor-specific SMC calls.
To support this hardware, add a ->program_key() method to
'struct cqhci_host_ops'. This allows overriding the standard CQHCI
crypto key programming / eviction procedure.
This is inspired by the corresponding UFS crypto support, which uses
these same SMC calls. See commit 1bc726e26e ("scsi: ufs: Add
program_key() variant op").
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Satya Tangirala <satyat@google.com>
Reviewed-and-tested-by: Peng Zhou <peng.zhou@mediatek.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210126001456.382989-6-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for eMMC inline encryption using the blk-crypto framework
(Documentation/block/inline-encryption.rst).
eMMC inline encryption support is specified by the upcoming JEDEC eMMC
v5.2 specification. It is only specified for the CQ interface, not the
non-CQ interface. Although the eMMC v5.2 specification hasn't been
officially released yet, the crypto support was already agreed on
several years ago, and it was already implemented by at least two major
hardware vendors. Lots of hardware in the field already supports and
uses it, e.g. Snapdragon 630 to give one example.
eMMC inline encryption support is very similar to the UFS inline
encryption support which was standardized in the UFS v2.1 specification
and was already upstreamed. The only major difference is that eMMC
limits data unit numbers to 32 bits, unlike UFS's 64 bits.
Like we did with UFS, make the crypto support opt-in by individual
drivers; don't enable it automatically whenever the hardware declares
crypto support. This is necessary because in every case we've seen,
some extra vendor-specific logic is needed to use the crypto support.
Co-developed-by: Satya Tangirala <satyat@google.com>
Signed-off-by: Satya Tangirala <satyat@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Satya Tangirala <satyat@google.com>
Reviewed-and-tested-by: Peng Zhou <peng.zhou@mediatek.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210125183810.198008-5-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the task descriptor initialization into cqhci_prep_task_desc().
In addition, make it explicitly initialize all 128 bits of the task
descriptor if the host controller is using 128-bit task descriptors,
rather than relying on the implicit zeroing from dmam_alloc_coherent().
This is needed to prepare for CQHCI inline encryption support, which
requires 128-bit task descriptors and uses the upper 64 bits.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Satya Tangirala <satyat@google.com>
Reviewed-and-tested-by: Peng Zhou <peng.zhou@mediatek.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210126001456.382989-4-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename cqhci.c to cqhci-core.c so that another source file can be added
to the cqhci module without having to rename the module.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-and-tested-by: Peng Zhou <peng.zhou@mediatek.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210126001456.382989-3-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Randy found that with the following Kconfig settings we have duplicate
definitions (e.g. __inittest()) in sdhci-of-aspeed due to competing
module_init()/module_exit() calls from kunit and driver the itself.
```
CONFIG_MMC_SDHCI_OF_ASPEED=m
CONFIG_MMC_SDHCI_OF_ASPEED_TEST=y
```
Conditionally open-code the kunit initialisation to avoid the error.
Fixes: 7efa02a981d6 ("mmc: sdhci-of-aspeed: Add KUnit tests for phase calculations")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20210122114852.3790565-1-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120142801.334550-3-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120142801.334550-2-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The RPi4 has an Arasan controller it carries over from the RPi3 and a newer
eMMC2 controller. Because of a couple of quirks, it seems wiser to bind
these controllers to the same driver that DT is using on this platform
rather than the generic sdhci_acpi driver with PNP0D40.
So, BCM2847 describes the older Arasan and BRCME88C describes the newer
eMMC2. The older Arasan is reusing an existing ACPI _HID used by other OSes
booting these tables on the RPi.
With this change, Linux is capable of utilizing the SD card slot, and the
Wi-Fi when booted with UEFI+ACPI on the RPi4.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210120000406.1843400-2-jeremy.linton@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Converting degrees of phase to logic delays is irritating to test on
hardware, so lets exercise the function using KUnit.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210114031433.2388532-5-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The AST2600 can achieve HS200 speeds with a change to the bus clock
divisor behaviour. The divisor can also be more accurate with respect
to the requested clock rate, but keep the one-hot behaviour for
backwards compatibility with the AST2400 and AST2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210114031433.2388532-4-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Aspeed SD/eMMC controllers expose configurable clock phase
correction by inserting delays of up to 15 logic elements in length into
the bus clock path. The hardware supports independent configuration for
both bus directions on a per-slot basis.
The timing delay per element encoded in the driver was experimentally
determined by scope measurements.
The phase controls for both slots are grouped together in a single
register of the global register block of the SD/MMC controller(s), which
drives the use of a locking scheme between the SDHCIs and the global
register set.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210114031433.2388532-3-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the following coccicheck warning:
./drivers/mmc/host/omap_hsmmc.c:297:6-25: WARNING: Comparison of 0/1 to
bool variable
According to the context, vqmmc_enabled is more suitable for bool type.
Reported-by: Abaci Robot<abaci@linux.alibaba.com>
Signed-off-by: Yang Li <abaci-bugfix@linux.alibaba.com>
Link: https://lore.kernel.org/r/1610704281-11036-1-git-send-email-abaci-bugfix@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using dev_err_probe() can avoid spamming logs when probe is deferred.
This function can also help to reduce code the size, uniform error handling
and simplify the code.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20210114152700.21916-5-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add struct device *dev in probe func() so that it can widely use in
probe to make code more readable.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20210114152700.21916-4-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use np pointer to simplify code and improve readability.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20210114152700.21916-3-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use of_device_get_match_data() helper to get the match-data.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20210114152700.21916-2-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GL9763E enters ASPM L1 state after a very short idle in default,
even during a burst of request. So the R/W performance of GL9763E
is low with some platforms, which support ASPM mechanism, due to
entering ASPM L1 state very frequently in R/W process. Set the L1
entry delay bits in vendor-specific register to 0x3FF to enlarge
the idle period to 260us for improving the R/W performance
of GL9763E.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Link: https://lore.kernel.org/r/20210115054736.27769-1-reniuschengl@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the controller present on the AM64x SoC.
There are instances:
sdhci0: 8bit bus width, max 400 MBps
sdhci1: 4bit bus width, max 100 MBps
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210113115908.3882-3-a-govindraju@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To make sure voltage is below 0.5V before power on during a power cycle,
add a delay of at least 100ms. The delays in the mmc core is not sufficient
for the rtsx pci device.
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20210113105723.7916-1-ricky_wu@realtek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the device suspend process begins before the mmc host's autosuspend
timeout, the host will continue running during system sleep. Avoid
this by forcing runtime suspend during a global suspend transition.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20210113052421.36553-1-samuel@sholland.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds new compatible string to differentiate
between the controllers versions included in the AP807
north bridge. Thanks to this change, the SoCs which use
AP807 will not run unintentionally in the 'slow mode'
with disabled UHS modes.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20210112094655.12274-3-kostap@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change code style of mapping the syscon in sdhci_arasan_update_support64b()
for readability and consistency.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210111155001.12307-3-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 36c6aadaae ("mmc: sdhci-of-arasan: Add support for Intel Keem Bay")
introduces syscon map sdhci_arasan_update_support64b(). Unfortunately,
kernel-doc format script tool has not been run before and causing warning
on the documentation style.
Below is the output when running the kernel-doc script tool:
drivers/mmc/host/sdhci-of-arasan.c:1388: warning: contents before sections
Let's fix this by using standard conventions kernel-doc format.
Fixes: 36c6aadaae ("mmc: sdhci-of-arasan: Add support for Intel Keem Bay")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210111155001.12307-2-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a vendor-specific bit named GLI_9763E_MB_ERP_ON at the bit7 of
register 888h to decide whether to enhance random R/W performance
of GL9763E. CQHCI support will be enabled if and only if the bit is
set and the GLI_9763E_MB_CMQ_OFF bit is not set.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Link: https://lore.kernel.org/r/20210106085332.5494-1-reniuschengl@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the datasheet, this controller needs retune when
cmd or data timeout happens. So, add a condition into .check_retune().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608708622-29668-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, busy timeout is not checked for data transfer command. But,
if the temperature condition changes, the data cannot be acquired
correctly and timeout may occur. Also, we could reproduce an issue by
using mmc_test driver (e.g. "Correct xfer_size at write (start
failure)"). Therefore, this adds timeout error check.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[saito: rework commit message.]
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[shimoda: rebase, add commit description]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608708622-29668-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable SGDMA support for SD_IO_RW_EXTENDED and add proper check
for scatterlist size alignment in block mode.
According to documentation, in SDIO block mode meson-gx DMA could
only handle buffers with sizes that are multiples of SDIO block size.
Some SDIO drivers like brcmfmac use scatterlist API, but do not enforce
proper scatterlist buffer size alignemnt, this looks like a root cause
of non-working CMD53.
Some minor style fixes.
Signed-off-by: Dmitry Lebed <lebed.dmitry@gmail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201218075312.67338-1-lebed.dmitry@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when get request SW timeout, if CMD/DAT xfer done irq coming right now,
then there is race between the msdc_request_timeout work and irq handler,
and the host->cmd and host->data may set to NULL in irq handler. also,
current flow ensure that only one path can go to msdc_request_done(), so
no need check the return value of cancel_delayed_work().
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20201218071611.12276-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add pre_req and post_req support to improve performance.
Inspired by a patch in the BSP by Masaharu Hayakawa.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608114572-1892-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the latest datasheet, the internal DMAC buffer alignment
R-Car Gen3 SDHI HW should be 128-bytes. So, fix it.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[shimoda: revise commit description, rebase]
Fixes: 2a68ea7896 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608114572-1892-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MSM SDHCI driver always set the "actual_clock" field to 0. It had
a comment about it not being needed because we weren't using the
standard SDHCI divider mechanism and we'd just fallback to
"host->clock". However, it's still better to provide the actual
clock. Why?
1. It will make timeout calculations slightly better. On one system I
have, the eMMC requets 200 MHz (for HS400-ES) but actually gets 192
MHz. These are close, but why not get the more accurate one.
2. If things are seriously off in the clock driver and it's missing
rates or picking the wrong rate (maybe it's rounding up instead of
down), this will make it much more obvious what's going on.
NOTE: we have to be a little careful here because the "actual_clock"
field shouldn't include the multiplier that sdhci-msm needs
internally.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/20201214092048.v5.2.I7564620993acd4baa63fa0e3925ca879a86d3ee3@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As talked about in commit 5e4b7e82d4 ("clk: qcom: gcc-sdm845: Use
floor ops for sdcc clks"), most clocks handled by the Qualcomm clock
drivers are rounded _up_ by default instead of down. We should make
sure SD/MMC clocks are always rounded down in the clock drivers.
Let's add a warning in the Qualcomm SDHCI driver to help catch the
problem.
This would have saved a bunch of time [1].
NOTE: this doesn't actually fix any problems, it just makes it obvious
to devs that there is a problem and that should be an indication to
fix the clock driver.
[1] http://lore.kernel.org/r/20201210102234.1.I096779f219625148900fc984dd0084ed1ba87c7f@changeid
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201214092048.v5.1.Iec3430c7d3c2a29262695edef7b82a14aaa567e5@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds support for A100 MMC controller, which use word address
for internal dma.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20201211011934.6171-10-andre.przywara@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI_PRESET_FOR_* registers are not set(all read as zeros), so
set the quirk.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201210165510.76b917e5@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A call to 'ausdhi6_dma_release()' to undo a previous call to
'usdhi6_dma_request()' is missing in the error handling path of the probe
function.
It is already present in the remove function.
Fixes: 75fa9ea6e3 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201217210922.165340-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'sdhci_remove_host()' and 'sdhci_pltfm_free()' should be used in place of
'mmc_remove_host()' and 'mmc_free_host()'.
This avoids some resource leaks, is more in line with the error handling
path of the probe function, and is more consistent with other drivers.
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Orson Zhai <orson.zhai@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201217204236.163446-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'dma_request_chan()' calls should be balanced by a corresponding
'dma_release_channel()' call.
Add the missing call both in the error handling path of the probe function
and in the remove function.
Fixes: ff65ffe46d ("mmc: Add Actions Semi Owl SoCs SD/MMC driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201209194202.54099-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The implementation of sdhci_pltfm_suspend() is only available when
CONFIG_PM_SLEEP is set, which triggers a linking error:
"undefined symbol: sdhci_pltfm_suspend" when building sdhci-brcmstb.c.
Fix this by implementing the missing stubs when CONFIG_PM_SLEEP is unset.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 5b191dcba7 ("mmc: sdhci-brcmstb: Fix mmc timeout errors on S5 suspend")
Cc: stable@vger.kernel.org
Tested-By: Nicolas Schichan <nschichan@freeebox.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e7b5d63a82 ("mmc: sdhci-brcmstb: Add shutdown callback")
that added a shutdown callback to the diver, is causing "mmc timeout"
errors on S5 suspend. The problem was that the "remove" was queuing
additional MMC commands after the "shutdown" and these caused
timeouts as the MMC queues were cleaned up for "remove". The
shutdown callback will be changed to calling sdhci-pltfm_suspend
which should get better power savings because the clocks will be
shutdown.
Fixes: e7b5d63a82 ("mmc: sdhci-brcmstb: Add shutdown callback")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210107221509.6597-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Automatic Clock Gating is a feature used for the power consumption
optimisation. It turned out that during early init phase it may prevent the
stable voltage switch to 1.8V - due to that on some platforms an endless
printout in dmesg can be observed: "mmc1: 1.8V regulator output did not
became stable" Fix the problem by disabling the ACG at very beginning of
the sdhci_init and let that be enabled later.
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201211141656.24915-1-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit a44f7cb937 ("mmc: core: use mrq->sbc when sending CMD23 for
RPMB") began to use ACMD23 for RPMB if the host supports ACMD23. In
RPMB ACM23 case, we need to set bit 31 to CMD23 argument, otherwise
RPMB write operation will return general fail.
However, no matter V4 is enabled or not, the dwcmshc's ARGUMENT2
register is 32-bit block count register which doesn't support stuff
bits of CMD23 argument. So let's handle this specific ACMD23 case.
From another side, this patch also prepare for future v4 enabling
for dwcmshc, because from the 4.10 spec, the ARGUMENT2 register is
redefined as 32bit block count which doesn't support stuff bits of
CMD23 argument.
Fixes: a44f7cb937 ("mmc: core: use mrq->sbc when sending CMD23 for RPMB")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201229161625.38255233@xhacker.debian
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Initial support for SD express card/host
MMC host:
- mxc: Convert the driver to DT-only
- mtk-sd: Add HS400 enhanced strobe support
- mtk-sd: Add support for the MT8192 SoC variant
- sdhci-acpi: Allow changing HS200/HS400 driver strength for AMDI0040
- sdhci-esdhc-imx: Convert the driver to DT-only
- sdhci-pci-gli: Improve performance for HS400 mode for GL9763E
- sdhci-pci-gli: Reduce power consumption for GL9755
- sdhci-xenon: Introduce ACPI support
- tmio: Fix command error processing
- tmio: Inform the core about the max_busy_timeout
- tmio/renesas_sdhi: Support custom calculation of busy-wait time
- renesas_sdhi: Reset SCC only when available
- rtsx_pci: Add SD Express mode support for RTS5261
- rtsx_pci: Various fixes and improvements for RTS5261
MEMSTICK:
- Minor fixes/improvements.
-----BEGIN PGP SIGNATURE-----
iQJLBAABCgA1FiEEugLDXPmKSktSkQsV/iaEJXNYjCkFAl/XZuAXHHVsZi5oYW5z
c29uQGxpbmFyby5vcmcACgkQ/iaEJXNYjCnYEBAAkHWJNCUILpqAcvc8VNpo2YJ3
vpLT1u4S3CgZ0DMJ8Oatgw6gaoTCJwX/qdXJPCCCsaiCg+H0rZATnq7/fp3CnPk+
NZ0JYoSxLTRIkaNaOxHDkR3P7JcJKy9pxUV6rvTQMK6rRtFxv9w7xrUTNOT5GiNj
5xB+uPrZ0AGhGdNaBU3/ZmmuCi1s8yf1B64IljqXTfQZJ6nvWbYFAWw8r4gfslfx
NLCo1+vwTOj3ADrgOI3eafFKKnME2bRgc/o/PM/iDciJlQfHnKzcQmDKSO4Rp89a
SVz5QYNfatfrjhgUv4DY/RsFEDlPbOiP71jKodcOSNoF5vjfNaudHhTNI1df0Pdw
/McFtKBIisrapDMa2wXwE7fTFLDUngACTc6FaSn86PyFU0wum3XEH90aqF9KKuQp
Ra88U/zsLUYE0jGkm6XWBsvmJHBZMTgFwXjlmdu52rnDRKccLgfCCTvb1oBGjrTj
ZMDokgrZ74JiAHu3o0VtKLGCtNVZBjVC6TqC1ZBIrXLOpALGZGkFW8iSXgiArMX+
NpMr9rExgobsAv02DTqWxlXLrEcUMO9IgM/TXbDQZP4hD5j1kzce9P5m59He9t/B
UMmJc5SEgdCbMjwuBORdB0qyW0g9So880E8uuk8kw5/I7F8ONsahCsKbZntvwOrY
s/UoF5RizRZhDJx2au4=
=1A/T
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Initial support for SD express card/host
MMC host:
- mxc: Convert the driver to DT-only
- mtk-sd: Add HS400 enhanced strobe support
- mtk-sd: Add support for the MT8192 SoC variant
- sdhci-acpi: Allow changing HS200/HS400 driver strength for AMDI0040
- sdhci-esdhc-imx: Convert the driver to DT-only
- sdhci-pci-gli: Improve performance for HS400 mode for GL9763E
- sdhci-pci-gli: Reduce power consumption for GL9755
- sdhci-xenon: Introduce ACPI support
- tmio: Fix command error processing
- tmio: Inform the core about the max_busy_timeout
- tmio/renesas_sdhi: Support custom calculation of busy-wait time
- renesas_sdhi: Reset SCC only when available
- rtsx_pci: Add SD Express mode support for RTS5261
- rtsx_pci: Various fixes and improvements for RTS5261
MEMSTICK:
- Minor fixes/improvements"
* tag 'mmc-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (72 commits)
dt-bindings: mmc: eliminate yamllint warnings
mmc: sdhci-xenon: introduce ACPI support
mmc: sdhci-xenon: use clk only with DT
mmc: sdhci-xenon: switch to device_* API
mmc: sdhci-xenon: use match data for controllers variants
dt-bindings: mmc: Fix xlnx,mio-bank property values for arasan driver
mmc: renesas_sdhi: populate hook for longer busy_wait
mmc: tmio: add hook for custom busy_wait calculation
mmc: tmio: set max_busy_timeout
dt-bindings: mmc: imx: fix the wrongly dropped imx8qm compatible string
mmc: sdhci-pci-gli: Disable slow mode in HS400 mode for GL9763E
mmc: sdhci: Use more concise device_property_read_u64
memstick: r592: Fix error return in r592_probe()
mmc: mxc: Convert the driver to DT-only
mmc: mxs: Remove the unused .id_table
mmc: sdhci-of-arasan: Fix fall-through warnings for Clang
mmc: sdhci-pci-gli: Reduce power consumption for GL9755
mmc: mediatek: depend on COMMON_CLK to fix compile tests
mmc: pxamci: Fix error return code in pxamci_probe
mmc: sdhci: Update firmware interface API
...
Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be more
and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iDZA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRMACgqxKS2CUcY8tPnR5weHEsbz6O+KAAn3BtEFnK
7V9EnSuZe4L1jNOHOB5V
=xzHh
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be
more and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates"
* tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (305 commits)
extcon: max77693: Fix modalias string
extcon: fsa9480: Support TI TSU6111 variant
extcon: fsa9480: Rewrite bindings in YAML and extend
dt-bindings: extcon: add binding for TUSB320
extcon: Add driver for TI TUSB320
slimbus: qcom: fix potential NULL dereference in qcom_slim_prg_slew()
siox: Make remove callback return void
siox: Use bus_type functions for probe, remove and shutdown
spmi: Add driver shutdown support
spmi: fix some coding style issues at the spmi core
spmi: get rid of a warning when built with W=1
uio: uio_hv_generic: use devm_kzalloc() for private data alloc
uio: uio_fsl_elbc_gpcm: use device-managed allocators
uio: uio_aec: use devm_kzalloc() for uio_info object
uio: uio_cif: use devm_kzalloc() for uio_info object
uio: uio_netx: use devm_kzalloc() for or uio_info object
uio: uio_mf624: use devm_kzalloc() for uio_info object
uio: uio_sercos3: use device-managed functions for simple allocs
uio: uio_dmem_genirq: finalize conversion of probe to devm_ handlers
uio: uio_dmem_genirq: convert simple allocations to device-managed
...
Previous patches dropped the strict dependency on the OF_*
in the sdhci-xenon driver. As a result the ACPI support
can be introduced (except for the XENON_A3700 variant)
by adding the necessary ID's in the acpi_match_table.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20201204171626.10935-5-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a preparation for supporting ACPI, modify the driver
to use the clk framework only when booting with DT -
otherwise rely on the configuration done by firmware.
For that purpose introduce also a custom SDHCI get_max_clock
callback.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20201204171626.10935-4-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to support both ACPI and DT, modify the driver
to use device_* routines for obtaining the properties
values.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20201204171626.10935-3-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a part of the ACPI support preparation resign from checking
compatible strings in the driver. Instead of that use a new
enum and assign the values to match data accordingly.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20201204171626.10935-2-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
rtsx_pcr:
add callback functions to support runtime PM
add delay_work to put device to D3 after idle
over 10 sec
rts5249:
add extra init flow for rtd3 and set rtd3_en from
config setting
rtsx_pci_sdmmc:
child device support autosuspend
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20201202065857.19412-1-ricky_wu@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #ifdef check for the suspend/resume functions is wrong:
drivers/mmc/host/mtk-sd.c:2765:12: error: unused function 'msdc_suspend' [-Werror,-Wunused-function]
static int msdc_suspend(struct device *dev)
drivers/mmc/host/mtk-sd.c:2779:12: error: unused function 'msdc_resume' [-Werror,-Wunused-function]
static int msdc_resume(struct device *dev)
Remove the #ifdef and mark all four as __maybe_unused to aovid the
problem.
Fixes: c0a2074ac5 ("mmc: mediatek: Fix system suspend/resume support for CQHCI")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201203222922.1067522-1-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of the EXTOP bit in R-Car Gen3 SoCs to have a twice as large
busy wait duration.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125213001.15003-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Newer SDHI variants can 'wait while busy' longer than the generic TMIO.
Provide a hook to get the maximum cycle count to wait for. If the hook
is not populated, fall back to a generic version which works well with
all older TMIO/SDHI variants.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125213001.15003-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set max_busy_timeouts for variants known to support the TOPxx bits in
the SD_OPTION register. The timeout mechanism was running in the
background but not yet properly handled in the driver. So, let the MMC
core know when to not use R1B to avoid unhandled timeouts.
My datasheets for older variants (tmio_mmc.c) suggest that they support
it, too. However, actual bit descriptions are lacking, so I chose an
opt-in approach.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125213001.15003-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Further testing of error cases revealed that downgrade is not enough, so
we need to reset the SCC which is done by calling the custom reset
function. This reset function can distinguish between the various SDHI
variants, so protecting the call with MIN_RCAR2 is enough here.
Fixes: 24ce2d7b8b ("mmc: tmio: bring tuning HW to a sane state with MMC_POWER_OFF")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125204953.3344-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The GL9763E uses 150Mhz (slow mode) by default in HS400 mode. In order
to make HS400 mode run at 200Mhz, the slow mode needs to be turned off.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20201125110145.2824-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since we only need a single u64 the _array form is
unnecessarily. Use device_property_read_u64 instead.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201125033630.603863-1-jeremy.linton@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201123203004.18792-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mxs-mmc driver is only used by DT platforms and the .id_table
is unused.
Get rid of it to simplify the code.
While at it, use of_device_get_match_data() to retrieve the driver
data.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201123191956.10542-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For GL9755, reduce power consumption by lowering the LFCLK and disabling
the DMACLK on low-power.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20201123053702.6083-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MFD_OMAP_USB_HOST uses Common Clock Framework thus it cannot be
built on platforms without it (e.g. compile test on MIPS with LANTIQ):
mips-linux-ld: drivers/mmc/host/mtk-sd.o: in function `msdc_ops_set_ios':
mtk-sd.c:(.text+0x2bbc): undefined reference to `clk_get_parent'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201122120056.100045-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return the error code from devm_gpiod_get_optional() instaed
of 0 in pxamci_probe().
Fixes: f54005b508 ("mmc: pxa: Use GPIO descriptor for power")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Link: https://lore.kernel.org/r/20201121021431.3168506-1-chengzhihao1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device_* calls were added a few years ago to abstract
DT/ACPI/fwnode firmware interfaces. Lets convert the two
sdhci caps fields to use the generic calls rather than the OF
specific ones. This has the side effect of allowing
ACPI based devices to quirk themselves when the caps field
is broken.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/r/20201120233831.447365-1-jeremy.linton@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 16ada730a7 ("mmc: sdhci-of-arasan: Modify clock operations
handling") introduced support for platform specific clock operations.
Around the same point in time the commit 36c6aadaae ("mmc:
sdhci-of-arasan: Add support for Intel Keem Bay") was also merged.
Unfortunate it was not really tested on top of the previously mentioned
commit, which causes clock registration failures for Keem Bay SOC devices.
Let's fix this, by properly declaring the clock operation for Keem Bay SOC
devices.
Fixes: 36c6aadaae ("mmc: sdhci-of-arasan: Add support for Intel Keem Bay")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201118120120.24908-2-muhammad.husaini.zulkifli@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDIO recheck fix is required for more of the supported variants. Let's
add it to those that needs it.
Reported-by: Fabien Parent <fparent@baylibre.com>
Reported-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Link: https://lore.kernel.org/r/20201119030237.9414-1-yong.mao@mediatek.com
Fixes: 9e2582e574 ("mmc: mediatek: fix SDIO irq issue")
Cc: stable@vger.kernel.org
[Ulf: Clarified commitmsg ]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mmc/host/sdhci-st.c:512:34: warning:
‘st_sdhci_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162344.485921-2-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mmc/host/sdhci-sprd.c:723:34: warning:
‘sdhci_sprd_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20201120162344.485921-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If some errors are detected at the same time as the access end
interrupt, the access end interrupt was not cleared. Especially with
DMA, because then the access end interrupt was never enabled and, thus,
never cleared. Clear the interrupt register always when a command error
occurs.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[saito: rebase to v5.4]
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: rebase and extension of the commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20201117131337.35307-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20201117113750.25053-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Printing kernel pointers is discouraged because they might leak kernel
memory layout. This fixes smatch warning:
drivers/mmc/host/tmio_mmc.c:177 tmio_mmc_probe() warn: argument 3 to %08lx specifier is cast from pointer
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201116164252.44078-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'busy_timeout' is in msecs, not in jiffies. Use the correct factor.
Fixes: 5e958e4aac ("sdhci: tegra: Implement Tegra specific set_timeout callback")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201116132206.23518-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the current implementation DLL reset will be issued for
each ITAP and OTAP setting inside ATF, this is creating issues
in some scenarios and this sequence is not inline with the TRM.
To fix the issue, DLL reset should be removed from the ATF and
host driver will request it explicitly.
This patch update host driver to explicitly request for DLL reset
before ITAP (assert DLL) and after OTAP (release DLL) settings.
Fixes: a5c8b2ae2e ("mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1605515565-117562-4-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Mask the ITAP and OTAP delay bits before updating with the new
tap value for Versal platform.
Fixes: 1a470721c8 ("sdhci: arasan: Add support for Versal Tap Delays")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1605515565-117562-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow configuring the Output and Input tap values with zero to avoid
failures in some cases (one of them is SD boot mode) where the output
and input tap values may be already set to non-zero.
Fixes: a5c8b2ae2e ("mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1605515565-117562-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Detect if tassadar_dll is required by using core version rather than
just specifying it in the sdhci_msm_variant_info.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/20201112173636.360186-1-dmitry.baryshkov@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A UHS setting of SDR25 can give better results for High Speed mode.
This is because there is no setting corresponding to high speed. Currently
SDHCI sets no value, which means zero which is also the setting for SDR12.
There was an attempt to change this in sdhci.c but it caused problems for
some drivers, so it was reverted and the change was made to sdhci-brcmstb
in commit 2fefc7c5f7 ("mmc: sdhci-brcmstb: Fix incorrect switch to HS
mode"). Several other drivers also do this.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v5.4+
Link: https://lore.kernel.org/r/20201112133656.20317-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It should use mmc_free_host to free mem in error patch of
msdc_drv_probe.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Liang <zhengliang6@huawei.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20201112092530.32446-1-zhengliang6@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use a macro to name the hardcoded values. Also, move the SDIF register
definition into the SDHI driver because this is an SDHI extension.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201111100244.15823-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
HOST_MODE should have a CTL_ prefix, too. This makes the code more
readable because we immediately know what it is. Also, remove the
hardcoded values with something readable, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201111100244.15823-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All previously called functions handle SCLKEN on their own, no need to
enable it again in sdhi_reset().
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110162151.37622-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no user of renesas_sdhi_reset_scc() anymore, only
renesas_sdhi_disable_scc() so merge these functions into one. I guess
the seperation was cruft anyhow. The BSP doesn't have it anymore and I
can't recall the reason we had it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110162151.37622-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We want to clear TAPEN in a software reset, too, to have a completely
known state. Especially when we doing the initial reset during boot to
clear previous firmware states.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110162151.37622-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 'reset' pointer is only populated for Gen2+. So, we don't need to
check for that flag inside the routine.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110142058.36393-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SCC pointer is currently filled whenever the SoC is Gen2+. This is
wrong because there is a Gen2-variant without SCC (SDHI_VER_GEN2_SDR50).
We have been lucky because the writes to unintended registers have not
caused problems so far. But further refactoring work exposed the
problem. So, move the pointer initialization to the place where we know
that the SDHI instance supports tuning. And also populate the 'reset'
pointer unconditionally to make sure the interrupt enable register is
always properly set for Gen2+.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110142058.36393-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting up the SCC parameters does not need a probed TMIO device. But in
the near future, probing the TMIO device needs the SCC parameters setup.
So, fix the ordering.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110142058.36393-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only re-initialize SCC and tuning when an SCC was found during probe().
This is currently a noop because all R-Car Gen2+ are considered to have
an SCC. But this will change in a later patch, so we need this
preparation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110142058.36393-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
pic32_sdhci_probe_platform() always returned 0, so there's no reason for
a return value. In addition, pic32_sdhci_probe() checked the return value
for possible error which is unnecessary.
Convert pic32_sdhci_probe_platform() to a void function and remove the
return value check. Fix the following Coccinelle warning:
./drivers/mmc/host/sdhci-pic32.c:127:5-8: Unneeded variable: "ret". Return "0" on line 137
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Link: https://lore.kernel.org/r/1604847648-13036-1-git-send-email-kaixuxia@tencent.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/mmc/host/meson-gx-mmc.c:1252:34: warning:
‘meson_mmc_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201103163046.14336-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add test mode for RTS5261.
If test mode is set, reader will switch to SD Express mode
mandatorily, and this mode is used by factory testing only.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1604397269-2780-1-git-send-email-rui_feng@realsil.com.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code has been in a irq-disabled context since it is hard IRQ. There
is no necessity to do it again.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1604278337-55624-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code has been in a irq-disabled context since it is hard IRQ. There
is no necessity to do it again.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/1604375323-33556-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
RTS5261 support SD mode and PCIe/NVMe mode. The workflow is as follows.
1.RTS5261 work in SD mode and set MMC_CAPS2_SD_EXP flag.
2.If card is plugged in, Host send CMD8 to ask card's PCIe availability.
3.If the card has PCIe availability and WP is not set, init_sd_express() will be invoked,
RTS5261 switch to PCIe/NVMe mode.
4.Mmc driver handover it to NVMe driver.
5.If card is unplugged, RTS5261 will switch to SD mode.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Link: https://lore.kernel.org/r/1603936703-3403-1-git-send-email-rui_feng@realsil.com.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MT8192 msdc is an independent sub system, we need control more bus
clocks for it.
Add support for the additional subsys clocks to allow it to be
configured appropriately.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Link: https://lore.kernel.org/r/20201014030846.12428-5-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This change will allow platform designers better control over signal
integrity by allowing them to tune the HS200 and HS400 driver strengths.
The driver strength was previously hard coded to A to solve boot
problems with certain platforms. This driver strength does not
universally apply to all platforms so we need a knob to adjust it.
All older platforms currently have the SDR104 preset hard coded to A in
the firmware. This means that switching from the hard coded value in
the kernel to reading the SDR104 preset is a no-op for these platforms.
Newer platforms will have properly set presets. So this change will
support both new and old platforms.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Victor Ding <victording@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201027084612.528301-1-victording@google.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver can match only via DT table so it should be always used and
the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant for sunxi). This
fixes compile warning:
drivers/mmc/host/sunxi-mmc.c:1181:34: warning: ‘sunxi_mmc_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201026153810.89512-3-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver uses GPIO Descriptor Consumer Interface so include proper
header to fix compile test errors like:
drivers/mmc/host/s3cmci.c: In function ‘s3cmci_check_sdio_irq’:
drivers/mmc/host/s3cmci.c:304:7: error:
implicit declaration of function ‘gpiod_get_value’; did you mean ‘gpio_get_value’? [-Werror=implicit-function-declaration]
drivers/mmc/host/s3cmci.c: In function ‘s3cmci_probe_pdata’:
drivers/mmc/host/s3cmci.c:1451:19: error:
implicit declaration of function ‘devm_gpiod_get_index’ [-Werror=implicit-function-declaration]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201026153810.89512-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit db1af1e971. It was
only a workaround to hide a regression. We now have proper fixes.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201106072549.1495-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When powering off a card, we need to disable the tuning HW (like SCC for
the Renesas SDHI) to get to a sane state and allow for re-tuning new
cards. This was hidden before because we wrongly did that in hw_reset()
before which was an unintended use of hw_reset(). Now that we corrected
the use of hw_reset() meanwhile, we revealed this shortcoming and need
to fix it properly by explicitly calling the downgrade callback.
Fixes: 6e7d4de108 ("mmc: renesas_sdhi: move wrong 'hw_reset' to 'reset'")
Suggested-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Reviewed-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201106072549.1495-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When applying a revert, the assumption that DMA only needs to be cleared
in specific cases was wrong. We want to reset the DMA controller every
time the rest of the HW gets reset, too.
Fixes: 34e3211e54 ("Revert "mmc: tmio: fix reset operation"")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201106072549.1495-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 94b110aff8 ("mmc: tmio: add tmio_mmc_host_alloc/free()")
added tmio_mmc_host_free(), but missed the function calling in
the sh_mobile_sdhi_remove() at that time. So, fix it. Otherwise,
we cannot rebind the sdhi/mmc devices when we use aliases of mmc.
Fixes: 94b110aff8 ("mmc: tmio: add tmio_mmc_host_alloc/free()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1604654730-29914-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- sdhci: Fix performance regression with auto CMD auto select
- sdhci-of-esdhc: Fix initialization for eMMC HS400 mode
- sdhci-of-esdhc: Fix timeout bug for tuning commands
-----BEGIN PGP SIGNATURE-----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=LDSp
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC host fixes from Ulf Hansson:
- sdhci: Fix performance regression with auto CMD auto select
- sdhci-of-esdhc: Fix initialization for eMMC HS400 mode
- sdhci-of-esdhc: Fix timeout bug for tuning commands
* tag 'mmc-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-of-esdhc: make sure delay chain locked for HS400
mmc: sdhci-of-esdhc: set timeout to max before tuning
mmc: sdhci: Use Auto CMD Auto Select only when v4_mode is true
For eMMC HS400 mode initialization, the DLL reset is a required step
if DLL is enabled to use previously, like in bootloader.
This step has not been documented in reference manual, but the RM will
be fixed sooner or later.
This patch is to add the step of DLL reset, and make sure delay chain
locked for HS400.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201020081116.20918-1-yangbo.lu@nxp.com
Fixes: 54e08d9a95 ("mmc: sdhci-of-esdhc: add hs400 mode support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
On rare occations there is the following error:
mmc0: Tuning timeout, falling back to fixed sampling clock
There are SD cards which takes a significant longer time to reply to the
first CMD19 command. The eSDHC takes the data timeout value into account
during the tuning period. The SDHCI core doesn't explicitly set this
timeout for the tuning procedure. Thus on the slow cards, there might be
a spurious "Buffer Read Ready" interrupt, which in turn triggers a wrong
sequence of events. In the end this will lead to an unsuccessful tuning
procedure and to the above error.
To workaround this, set the timeout to the maximum value (which is the
best we can do) and the SDHCI core will take care of the proper timeout
handling.
Fixes: ba49cbd093 ("mmc: sdhci-of-esdhc: add tuning support")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201022222337.19857-1-michael@walle.cc
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-of-dwcmshc meets an eMMC read performance regression with below
command after commit 427b6514d0 ("mmc: sdhci: Add Auto CMD Auto
Select support"):
dd if=/dev/mmcblk0 of=/dev/null bs=8192 count=100000
Before the commit, the above command gives 120MB/s
After the commit, the above command gives 51.3 MB/s
So it looks like sdhci-of-dwcmshc expects Version 4 Mode for Auto
CMD Auto Select. Fix the performance degradation by ensuring v4_mode
is true to use Auto CMD Auto Select.
Fixes: 427b6514d0 ("mmc: sdhci: Add Auto CMD Auto Select support")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201015174115.4cf2c19a@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After the conversions of the reset routines, re-inserting SD cards
didn't work anymore. Apply this temporary workaround to have working SD
cards during the merge window. The issue will be fixed properly until
the final release.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20201008092533.76588-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add CQHCI initialization and implement CQHCI operations for GL9763E.
Use bit19 of the register (0x888) to decide whether to disable command
queuing. If the bit is set, the command queuing will be disabled.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20201005105509.11343-1-ben.chuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This change fixes HS400 tuning for devices with invalid presets.
SDHCI presets are not currently used for eMMC HS/HS200/HS400, but are
used for DDR52. The HS400 retuning sequence is:
HS400->DDR52->HS->HS200->Perform Tuning->HS->HS400
This means that when HS400 tuning happens, we transition through DDR52
for a very brief period. This causes presets to be enabled
unintentionally and stay enabled when transitioning back to HS200 or
HS400. Some firmware has invalid presets, so we end up with driver
strengths that can cause I/O problems.
Fixes: 34597a3f60 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200928154718.1.Icc21d4b2f354e83e26e57e270dc952f5fe0b0a40@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.
[1] https://www.ti.com/lit/pdf/spract9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20200923105206.7988-6-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.
With this addition, make sure that DLL is always switched off at the
beginning of the set_clock() call to simplify configuration. This also
removes the need for the dll_on member in struct sdhci_am654_data.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200923105206.7988-5-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bit ESDHC_PERIPHERAL_CLK_SEL to select using peripheral clock
or platform clock is not able to be reset by SDHCI_RESET_ALL.
So driver needs to initialize it as 1 or 0 once, to override the
different value which may be configured in bootloader.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20200927082304.9232-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit bedf9fc01f ("mmc: sdhci: Workaround broken command queuing on
Intel GLK"), disabled command-queuing on Intel GLK based LENOVO models
because of it being broken due to what is believed to be a bug in
the BIOS.
It seems that the BIOS of some IRBIS models, including the IRBIS NB111
model has the same issue, so disable command queuing there too.
Fixes: bedf9fc01f ("mmc: sdhci: Workaround broken command queuing on Intel GLK")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209397
Reported-and-tested-by: RussianNeuroMancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200927104821.5676-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The struct of_device_id is not defined with !CONFIG_OF so its forward
declaration should be hidden to as well. This should address clang
compile warning:
drivers/mmc/host/sdhci-s3c.c:464:34: warning: tentative array definition assumed to have one element
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200925072532.10272-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 'struct mmc_host *mmc' comes from drvdata set at the end of probe,
so it cannot be NULL. The code already dereferences it few lines before
the check with mmc_priv(). This also fixes smatch warning:
drivers/mmc/host/moxart-mmc.c:692 moxart_remove() warn: variable dereferenced before check 'mmc' (see line 688)
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200923153739.30327-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core has now a generic check if some tuning is in progress. Its
protected area is a bit larger than the custom one in this driver but we
concluded that this works equally well for the intended case. So, drop
the local flag and switch to the generic one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200922172253.4458-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MediaTek MMC driver uses pointer to get from private
msdc_host structure to the generic mmc_host structure.
However mmc_host always precedes msdc_host in memory so compute
its address with a subtraction (which is cheaper than a dereference)
using mmc_from_priv() and drop the extra pointer.
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Link: https://lore.kernel.org/r/20200917192624.548720-1-ameynarkhede03@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If CONFIG_NO_DMA=y (e.g. Sun-3 allmodconfig):
drivers/mmc/host/mmc_spi.c:1323:15: warning: return type defaults to ‘int’ [-Wreturn-type]
static inline mmc_spi_dma_alloc(struct mmc_spi_host *host) { return 0; }
^~~~~~~~~~~~~~~~~
Fix this by adding the missing return type.
Fixes: a395acf0f6 ("mmc: mmc_spi: Allow the driver to be built when CONFIG_HAS_DMA is unset")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20200914094243.3912-1-geert@linux-m68k.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/890ae5601594fca5de104695a682f4b6efbc631b.1599660554.git.viresh.kumar@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some R-Car Gen3 SoCs need some manual correction of timing parameters
after the automatic tuning has finished but before next CMD13 is
completed. This patch implements that by this state machine:
- introducing a per-SoC correction table if needed
- iff such a table exists, the 'fixup_request' callback is populated
during probe
- iff such a table exists, a runtime flag ('needs_adjust_hs400')
is set when HS400 tuning was completed
- the callback will check the runtime flag and enable the corrected
manual mode if the flag is set and CMD13 is encountered
- at the end of the enablement the runtime flag is cleared
- iff the configuration flag is set, the manual mode will be disabled
when HS400 gets downgraded
There also some helper functions added to access the TMPPORT registers.
The actual correction table is SoC and instance(!) specific and is
added to the quirks struct.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20200902081812.1591-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to have been added after kernel 5.4.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Lars Povlsen <lars.povlsen@microchip.com>
Acked-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200903162412.6.Ib121debfb18e5f923a3cd38fe9c36aa086c650c5@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v5.4 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200903162412.5.I2b630c4d40ff4ea61d5b30b8ccfe95890e257100@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.19 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200903162412.4.I84eb3e0a738635d524c90d1a688087bc295f7c32@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.14 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # SDHI drivers
Link: https://lore.kernel.org/r/20200903162412.3.Id1ff21470f08f427aedd0a6535dcd83ccc56b278@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.9 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200903162412.2.I226782b43191ce367fa3bc1c907c29f571890412@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.4 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # SH_MMCIF
Tested-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200903162412.1.Id501e96fa63224f77bb86b2135a5e8324ffb9c43@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Multiple MMC host controller driver can be compile tested as they do not
depend on architecture specific headers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907105254.31097-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All entries in Kconfig are already part of "if MMC", so there is no need
for additional dependency on MMC.
Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200904164315.24618-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 9495b7e92f ("driver core: platform: Initialize dma_parms
for platform devices"), struct platform_device already provides a
dma_parms structure, so we can save allocating another one.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/85e1fc97dbec3dea96102785a5e308ccb5e91cfe.1599167798.git.robin.murphy@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because clk_disable_unprepare already checked NULL clock parameter, so the
additional checks are unnecessary, just remove them.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20200903084825.85616-1-vulab@iscas.ac.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tuning procedure switches to lower frequencies but that will turn the
SCC off and accessing its register then will hang. So, check when we are
tuning and keep the current setup of the external clock if we are doing
so. Note that we still switch to the lower frequency because of the
internal divider. We just make sure to not modify the external clock.
This patch depends on a MMC core patch calling the downgrade function
earlier.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200901150250.26236-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turning on initcall debug on one system showed this:
initcall sdhci_msm_driver_init+0x0/0x28 returned 0 after 34782 usecs
The lion's share of this time (~33 ms) was in mmc_power_up(). This
shouldn't be terribly surprising since there are a few calls to delay
based on "power_delay_ms" and the default delay there is 10 ms.
Because we haven't specified that we'd prefer asynchronous probe for
this driver then we'll wait for this driver to finish before we start
probes for more drivers. While 33 ms doesn't sound like tons, every
little bit counts.
There should be little problem with turning on asynchronous probe for
this driver. It's already possible that previous drivers may have
turned on asynchronous probe so we might already have other things
(that probed before us) probing at the same time we are anyway. This
driver isn't really providing resources (clocks, regulators, etc) that
other drivers need to probe and even if it was they should be handling
-EPROBE_DEFER.
Let's turn this on and get a bit of boot speed back.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200902164303.1.I5e598a25222b4534c0083b61dbfa4e0e76f66171@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 'imask' and 'bsize' are not used in dbg_dumpregs:
drivers/mmc/host/s3cmci.c:149:36: warning: variable 'imask' set but not used [-Wunused-but-set-variable]
drivers/mmc/host/s3cmci.c:148:63: warning: variable 'bsize' set but not used [-Wunused-but-set-variable]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200903054333.18331-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since driver data is a pointer, direct casting to integer causes
warning when compile testing for 64-bit architecture:
drivers/mmc/host/s3cmci.c:1495:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
The actual driver data can be only 0 or 1, so cast it via long and do
not care about any loss of value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902204847.2764-3-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
iomem pointers should be printed with pointer format to hide the
actual value and fix warnings when compile testing for 64-bit
architecture:
drivers/mmc/host/s3cmci.c:1355:46: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902204847.2764-2-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Store in interrupt service routine always '1' in end_command, not the
value of host->cmd to fix compile test warnings on RISC-V:
drivers/mmc/host/davinci_mmc.c:999:17: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902204847.2764-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only -ENOENT from devm_clk_get() means that clock is not present in
device tree. Other errors have their own meaning and should not be
ignored.
Simplify getting the clock which is in fact optional and also use
dev_err_probe() for handling deferred.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200902193658.20539-7-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_addr_t size varies between architectures so use dedicated printk
format to fix compile testing warning (e.g. on 32-bit MIPS):
drivers/mmc/host/sdhci-of-sparx5.c:63:11: warning:
format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 5 has type ‘dma_addr_t {aka unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-11-krzk@kernel.org
Acked-by: Lars Povlsen <larc.povlsen@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code, the error value gets printed and real error
from dw_mci_parse_dt() is passed further instead of fixed -EINVAL.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-10-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-9-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-8-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-6-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-5-krzk@kernel.org
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-4-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-3-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200902193658.20539-2-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The emmc2 interface on the bcm2711 supports DDR modes for eMMC devices
running at 3.3V. This allows to run eMMC module with 3.3V signaling voltage
at DDR52 mode on the Raspberry Pi 4 using a SD adapter:
clock: 52000000 Hz
actual clock: 50000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 2 (4 bits)
timing spec: 8 (mmc DDR52)
signal voltage: 0 (3.30 V)
driver type: 0 (driver type B)
Link: https://github.com/raspberrypi/linux/issues/3802
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1598651234-29826-1-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CQHCI_ENABLE bit in CQHCI_CFG should be disabled
after msdc_cqe_disable(), and should be enabled before
msdc_ceq_enable() for MTK platform.
Add hook functions for cqhci_host_ops->pre_enable() and
cqhci_host_ops->post_disable().
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1598520783-25250-3-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add pre_enable() and post_disable() for cqhci_host_ops.
Add hook functions before cqhci enable and
after cqhci disable for platforms need them.
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1598520783-25250-2-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On sc7180 target, issues are observed with HS400 mode due to a
hardware limitation. If sdcc clock is dynamically gated and ungated,
the very next command is failing with command CRC/timeout errors.
To mitigate this issue, DLL phase has to be restored whenever sdcc
clock is gated dynamically. The restore_dll_config ensures this.
Enabling this flag with this change. And simply re-using the sdm845
target configuration for this flag.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1598541694-15694-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After all the previous refactorization, we can now populate mmc_ops
directly and don't need a layer inbetween. The NULL-pointer check and
the error printout are already done by the MMC core.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-7-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHI needs to reset the SCC only, not the whole IP core. So, if tuning
fails, don't handle specifics in the generic TMIO core, but in the
specific drivers. For SDHI, we need to move around the reset routine a
bit. It is not modified.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-6-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some TMIO variants need specific actions in their reset routine, but
they are all based on a generic reset routine. So, the optional 'reset'
callback will now only take care of the additional stuff and we will
have a generic function around it. Less code, easier to maintain, and
much more readable. Code in tmio_mmc.c is untested but in my TC6387XB
datasheet the SDIO part is reset independently from the SD part, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After Yamada-san's refactorization introducing 'tmio_mmc_host_alloc', we
can populate mmc_ops directly and don't need a layer inbetween.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit a87852c6b8. It did fix
the issue, but was building on top of already wrong assumptions. The
driver missed that 'hw_reset' was only for resetting remote HW (card)
and not for the IP core. Since we fixed that in a previous patch, we can
now remove this patch to make it clear that 'reset' is for resetting the
IP core only. Also, cancelling DMA will only be called when actually
needed again. It will also allow for further cleanups and better
readability. Note that in addition to the revert, the call in
'tmio_mmc_execute_tuning' will be converted, too, to maintain the
current behaviour.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver got the usage of 'hw_reset' wrong and missed that it is used
to reset the remote HW (card) only, not the local one (controller). Move
everything to the proper 'reset' callback. Also, add the generic reset
code from TMIO, so we will ensure the same behaviour (it will get
refactored away in a later patch). This also means we need to drop
MMC_CAP_HW_RESET because this is currently not supported by our
hardware.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a one time delay because of a card detect debounce timer in the
controller IP. This timer runs as soon as power is applied to the module
regardless of whether a card is present or not and any writes to
SDHCI_POWER_ON will return 0 before it expires. This timeout has been
measured to be about 1 second in am654x and j721e.
Write-and-read-back in a loop on SDHCI_POWER_ON for a maximum of
1.5 seconds to make sure that the controller actually powers on.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200825170015.32285-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There seems to be no particular reason to only test for ARM, so allow
for build-testing on other platforms to increase coverage.
Build-tested on x86 with allyesconfig.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200824171854.406157-1-alex.dewar90@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds the eMMC driver for the Sparx5 SoC. It is based upon the
designware IP, but requires some extra initialization and quirks.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200825081357.32354-3-lars.povlsen@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
via_save_pcictrlreg() should be called with host->lock held
as it writes to pm_pcictrl_reg, otherwise there can be a race
condition between via_sd_suspend() and via_sdc_card_detect().
The same pattern is used in the function via_reset_pcictrl()
as well, where via_save_pcictrlreg() is called with host->lock
held.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200822061528.7035-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some Intel BYT based host controllers support the setting of latency
tolerance. Accordingly, implement the PM QoS ->set_latency_tolerance()
callback. The raw register values are also exposed via debugfs.
Intel EHL controllers require this support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: cb3a7d4a0a ("mmc: sdhci-pci: Add support for Intel EHL")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200818104508.7149-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Previously the cycle timeout was converted to a microsecond value but
then incorrectly treated as a nanosecond timeout. This patch changes
the code to convert both the nanosecond timeout and the cycle timeout
to a microsecond value and use that directly.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20200814185011.3252020-1-t.schramm@manjaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to IC suggestion, everytime before sending the tuning command,
need to reset the usdhc, so to reset the tuning circuit, to let every
tuning command work well for the manual tuning method. For standard tuning
method, IC already add the reset operation in the hardware logic.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1597135057-22272-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove empty comment to fix W=1 compile warning:
drivers/mmc/host/s3cmci.c:400: warning: Cannot understand *
on line 400 - I thought it was a doc line
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200804151345.28005-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200718090614.88946-1-grandmaster@al2klimov.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit b214fe592a ("mmc: sdhci-of-esdhc: add erratum eSDHC7 support")
added code to check for a specific compatible string in the device-tree
on every esdhc interrupat. Instead of doing this record the quirk in
struct sdhci_esdhc and lookup the struct in esdhc_irq.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200903012029.25673-1-chris.packham@alliedtelesis.co.nz
Fixes: b214fe592a ("mmc: sdhci-of-esdhc: add erratum eSDHC7 support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit cd57d07b1e ("sh: don't allow non-coherent DMA for NOMMU") made
CONFIG_NO_DMA to be set for some platforms, for good reasons.
Consequentially, CONFIG_HAS_DMA doesn't get set, which makes the DMA
mapping interface to be built as stub functions, but also prevent the
mmc_spi driver from being built as it depends on CONFIG_HAS_DMA.
It turns out that for some odd cases, the driver still relied on the DMA
mapping interface, even if the DMA was not actively being used.
To fixup the behaviour, let's drop the build dependency for CONFIG_HAS_DMA.
Moreover, as to allow the driver to succeed probing, let's move the DMA
initializations behind "#ifdef CONFIG_HAS_DMA".
Fixes: cd57d07b1e ("sh: don't allow non-coherent DMA for NOMMU")
Reported-by: Rich Felker <dalias@libc.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20200901150438.228887-1-ulf.hansson@linaro.org
As the comments in this patch say, if we tune and find all phases are
valid it's _almost_ as bad as no phases being found valid. Probably
all phases are not really reliable but we didn't detect where the
unreliable place is. That means we'll essentially be guessing and
hoping we get a good phase.
This is not just a problem in theory. It was causing real problems on
a real board. On that board, most often phase 10 is found as the only
invalid phase, though sometimes 10 and 11 are invalid and sometimes
just 11. Some percentage of the time, however, all phases are found
to be valid. When this happens, the current logic will decide to use
phase 11. Since phase 11 is sometimes found to be invalid, this is a
bad choice. Sure enough, when phase 11 is picked we often get mmc
errors later in boot.
I have seen cases where all phases were found to be valid 3 times in a
row, so increase the retry count to 10 just to be extra sure.
Fixes: 415b5a75da ("mmc: sdhci-msm: Add platform_execute_tuning implementation")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200827075809.1.If179abf5ecb67c963494db79c3bc4247d987419b@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 61d7437ed1 ("mmc: sdhci-acpi: Fix HS400 tuning for AMDI0040")
broke resume for eMMC HS400. When the system suspends the eMMC controller
is powered down. So, on resume we need to reinitialize the controller.
Although, amd_sdhci_host was not getting cleared, so the DLL was never
re-enabled on resume. This results in HS400 being non-functional.
To fix the problem, this change clears the tuned_clock flag, clears the
dll_enabled flag and disables the DLL on reset.
Fixes: 61d7437ed1 ("mmc: sdhci-acpi: Fix HS400 tuning for AMDI0040")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200831150517.1.I93c78bfc6575771bb653c9d3fca5eb018a08417d@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit b5a84ecf02 ("mmc: tegra: Add Tegra210 support")
Tegra210 and later has a separate sdmmc_legacy_tm (TMCLK) used by Tegra
SDMMC hawdware for data timeout to achive better timeout than using
SDCLK and using TMCLK is recommended.
USE_TMCLK_FOR_DATA_TIMEOUT bit in Tegra SDMMC register
SDHCI_TEGRA_VENDOR_SYS_SW_CTRL can be used to choose either TMCLK or
SDCLK for data timeout.
Default USE_TMCLK_FOR_DATA_TIMEOUT bit is set to 1 and TMCLK is used
for data timeout by Tegra SDMMC hardware and having TMCLK not enabled
is not recommended.
So, this patch adds quirk NVQUIRK_HAS_TMCLK for SoC having separate
timeout clock and keeps TMCLK enabled all the time.
Fixes: b5a84ecf02 ("mmc: tegra: Add Tegra210 support")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1598548861-32373-8-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 4346b7c794 ("mmc: tegra: Add Tegra186 support")
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK is set for Tegra186 from the
beginning of its support in driver.
Tegra186 SDMMC hardware by default uses timeout clock (TMCLK) instead
of SDCLK and this quirk should not be set.
So, this patch remove this quirk for Tegra186.
Fixes: 4346b7c794 ("mmc: tegra: Add Tegra186 support")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1598548861-32373-3-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit b5a84ecf02 ("mmc: tegra: Add Tegra210 support")
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK is set for Tegra210 from the
beginning of Tegra210 support in the driver.
Tegra210 SDMMC hardware by default uses timeout clock (TMCLK)
instead of SDCLK and this quirk should not be set.
So, this patch remove this quirk for Tegra210.
Fixes: b5a84ecf02 ("mmc: tegra: Add Tegra210 support")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1598548861-32373-2-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fixs eMMC-Access on mt7622/Bpi-64.
Before we got these Errors on mounting eMMC ion R64:
[ 48.664925] blk_update_request: I/O error, dev mmcblk0, sector 204800 op 0x1:(WRITE)
flags 0x800 phys_seg 1 prio class 0
[ 48.676019] Buffer I/O error on dev mmcblk0p1, logical block 0, lost sync page write
This patch adds a optional reset management for msdc.
Sometimes the bootloader does not bring msdc register
to default state, so need reset the msdc controller.
Cc: <stable@vger.kernel.org> # v5.4+
Fixes: 966580ad23 ("mmc: mediatek: add support for MT7622 SoC")
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20200814014346.6496-4-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For Intel controllers, SDHCI_RESET_ALL resets also CQHCI registers.
Normally, SDHCI_RESET_ALL is not used while CQHCI is enabled, but that can
happen on the error path. e.g. if mmc_cqe_recovery() fails, mmc_blk_reset()
is called which, for a eMMC that does not support HW Reset, will cycle the
bus power and the driver will perform SDHCI_RESET_ALL.
So whenever performing SDHCI_RESET_ALL ensure CQHCI is deactivated.
That will force the driver to reinitialize CQHCI when it is next used.
A similar change was done already for sdhci-msm, and other drivers using
CQHCI might benefit from a similar change, if they also have CQHCI reset
by SDHCI_RESET_ALL.
Fixes: 8ee82bda23 ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Cc: stable@vger.kernel.org # 5.4.x: 0ffa6cfbd9: mmc: cqhci: Add cqhci_deactivate()
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200819121848.16967-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The AMD eMMC Controller can only use the tuned clock while in HS200 and
HS400 mode. If we switch to a different mode, we need to disable the
tuned clock. If we have previously performed tuning and switch back to
HS200 or HS400, we can re-enable the tuned clock.
Previously the tuned clock was not getting disabled when switching to
DDR52 which is part of the HS400 tuning sequence.
Fixes: 34597a3f60 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200819125832.v2.1.Ie8f0689ec9f449203328b37409d1cf06b565f331@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rather than call the internal s3c_gpio_cfgall_range() function
through a platform header, move the code into the set_power
callback that is already exported by the board, and add
a default implementation.
In DT mode, the code already does not set the pin config,
so nothing changes there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200806182059.2431-29-krzk@kernel.org
[krzk: Rebase and correct set_power in mach-h1940.c]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The plat-samsung directory and mach-s5pv210 can be build
completely independently, so split the two Kconfig symbols
CONFIG_PLAT_SAMSUNG and CONFIG_ARCH_S5PV210.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-18-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Now that no code in arch/arm is shared between mach-exynos and the
others, make the split formal.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200806182059.2431-15-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The s3cmci driver does not use machine header mach/dma.h.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
- Add a new host cap bit and a corresponding DT property, to support power
cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host:
- Convert a few DT bindings to the json-schema
- mtk-sd: Add support for command queue through cqhci
- mtk-sd: Add support for the MT6779 variant
- renesas_sdhi_internal_dmac: Fix dma unmapping in the error path
- sdhci_am654: Add support for the AM65x PG2.0 variant
- sdhci_am654: Extend support for phys/clocks
- sdhci-cadence: Drop incorrect HW tuning for SD mode
- sdhci-msm: Add support for interconnect bandwidth scaling
- sdhci-msm: Enable internal voltage control
- sdhci-msm: Enable low power state for pinctrls
- sdhci-of-at91: Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli: Improve clock handling for GL975x
- sdhci-pci-o2micro: Add HW tuning for SDR104 mode
- sdhci-pci-o2micro: Fix support for O2 host controller Seabird1
-----BEGIN PGP SIGNATURE-----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=AwwR
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add a new host cap bit and a corresponding DT property, to support
power cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo
cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host controllers:
- Convert a few DT bindings to the json-schema
- mtk-sd:
- Add support for command queue through cqhci
- Add support for the MT6779 variant
- renesas_sdhi_internal_dmac:
- Fix dma unmapping in the error path
- sdhci_am654:
- Add support for the AM65x PG2.0 variant
- Extend support for phys/clocks
- sdhci-cadence:
- Drop incorrect HW tuning for SD mode
- sdhci-msm:
- Add support for interconnect bandwidth scaling
- Enable internal voltage control
- Enable low power state for pinctrls
- sdhci-of-at91:
- Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli:
- Improve clock handling for GL975x
- sdhci-pci-o2micro:
- Add HW tuning for SDR104 mode
- Fix support for O2 host controller Seabird1"
* tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (66 commits)
mmc: mediatek: make function msdc_cqe_disable() static
MAINTAINERS: mmc: sdhci-of-at91: handover maintenance to Eugen Hristev
dt-bindings: mmc: mediatek: Add document for mt6779
mmc: mediatek: command queue support
mmc: mediatek: refine msdc timeout api
mmc: mediatek: add MT6779 MMC driver support
mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode
mmc: sdhci-pci-o2micro: Bug fix for O2 host controller Seabird1
mmc: via-sdmmc: use generic power management
memstick: jmb38x_ms: use generic power management
mmc: sdhci-cadence: do not use hardware tuning for SD mode
mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL975x
mmc: cqhci: Fix a print format for the task descriptor
mmc: sdhci-of-arasan: fix timings allocation code
mmc: sdhci: Fix a potential uninitialized variable
dt-bindings: mmc: renesas,sdhi: convert to YAML
dt-bindings: mmc: convert arasan sdhci bindings to yaml
mmc: sdhci: Fix potential null pointer access while accessing vqmmc
mmc: core: Add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
dt-bindings: mmc: Add full-pwr-cycle-in-suspend property
...
Here is the large set of char and misc and other driver subsystem
patches for 5.9-rc1. Lots of new driver submissions in here, and
cleanups and features for existing drivers.
Highlights are:
- habanalabs driver updates
- coresight driver updates
- nvmem driver updates
- huge number of "W=1" build warning cleanups from Lee Jones
- dyndbg updates
- virtbox driver fixes and updates
- soundwire driver updates
- mei driver updates
- phy driver updates
- fpga driver updates
- lots of smaller individual misc/char driver cleanups and fixes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXylccQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymofgCfZ1CxNWd0ZVM0YIn8cY9gO6ON7MsAnRq48hvn
Vjf4rKM73GC11bVF4Gyy
=Xq1R
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char and misc and other driver subsystem
patches for 5.9-rc1. Lots of new driver submissions in here, and
cleanups and features for existing drivers.
Highlights are:
- habanalabs driver updates
- coresight driver updates
- nvmem driver updates
- huge number of "W=1" build warning cleanups from Lee Jones
- dyndbg updates
- virtbox driver fixes and updates
- soundwire driver updates
- mei driver updates
- phy driver updates
- fpga driver updates
- lots of smaller individual misc/char driver cleanups and fixes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (322 commits)
habanalabs: remove unused but set variable 'ctx_asid'
nvmem: qcom-spmi-sdam: Enable multiple devices
dt-bindings: nvmem: SID: add binding for A100's SID controller
nvmem: update Kconfig description
nvmem: qfprom: Add fuse blowing support
dt-bindings: nvmem: Add properties needed for blowing fuses
dt-bindings: nvmem: qfprom: Convert to yaml
nvmem: qfprom: use NVMEM_DEVID_AUTO for multiple instances
nvmem: core: add support to auto devid
nvmem: core: Add nvmem_cell_read_u8()
nvmem: core: Grammar fixes for help text
nvmem: sc27xx: add sc2730 efuse support
nvmem: Enforce nvmem stride in the sysfs interface
MAINTAINERS: Add git tree for NVMEM FRAMEWORK
nvmem: sprd: Fix return value of sprd_efuse_probe()
drivers: android: Fix the SPDX comment style
drivers: android: Fix a variable declaration coding style issue
drivers: android: Remove braces for a single statement if-else block
drivers: android: Remove the use of else after return
drivers: android: Fix a variable declaration coding style issue
...
The sparse tool complains as follows:
drivers/mmc/host/mtk-sd.c:2269:6: warning:
symbol 'msdc_cqe_disable' was not declared. Should it be static?
This function is not used outside of mtk-sd.c, so this commit
marks it static.
Fixes: 88bd652b3c ("mmc: mediatek: command queue support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Link: https://lore.kernel.org/r/20200727171129.2945-1-weiyongjun1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the newly introduced pm_ptr() macro to simplify the code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Support command queue for mt6779 platform.
a. Add msdc_set_busy_timeout() to calculate emmc write timeout.
b. Connect mtk msdc driver to cqhci driver through
host->cq_host->ops = &msdc_cmdq_ops;
c. msdc_cmdq_irq() will link up with cqchi_irq(). Besides, it provides
more irq error messages like RSPCRCERR/CMDTO/DATACRCERR/DATTMO.
d. Select kernel config MMC_CQHCI for MMC_MTK
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Acked-by: Yong Mao <yong.mao@mediatek.com>
Link: https://lore.kernel.org/r/1595205759-5825-4-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Extract msdc timeout api common part to have
better code architecture and avoid redundant code.
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1595205759-5825-3-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To fix support for the O2 host controller Seabird1, set the quirk
SDHCI_QUIRK2_PRESET_VALUE_BROKEN and the capability bit MMC_CAP2_NO_SDIO.
Moreover, assign the ->get_cd() callback.
Signed-off-by: Shirley Her <shirley.her@bayhubtech.com>
Link: https://lore.kernel.org/r/20200721011733.8416-1-shirley.her@bayhubtech.com
[Ulf: Updated the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.
With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.
This driver makes use of PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device(),
pci_enable_wake() and pci_set_power_state() and to do required operations.
In generic mode, they are no longer needed.
Change function parameter in both .suspend() and .resume() to
"struct device*" type. Use dev_get_drvdata() to get drv data.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Link: https://lore.kernel.org/r/20200720142603.577323-1-vaibhavgupta40@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As commit ef6b75671b ("mmc: sdhci-cadence: send tune request twice to
work around errata") stated, this IP has an errata. This commit applies
the second workaround for the SD mode.
Due to the errata, it is not possible to use the hardware tuning provided
by SDHCI_HOST_CONTROL2.
Use the software-controlled tuning like the eMMC mode.
Set sdhci_host_ops::platform_execute_tuning instead of overriding
mmc_host_ops::execute_tuning.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20200720061141.172944-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The initial code that was adding delays was doing a cast over undefined
memory. This meant that the delays would be all gibberish.
This change, allocates all delays on the stack, and assigns them from the
ZynqMP & Versal macros/phase-list. And then finally copies them over the
common iclk_phase & oclk_phase variables.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1594753953-62980-1-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Smatch complains that "ret" can be used without being initialized.
drivers/mmc/host/sdhci.c
4383 if (!IS_ERR(mmc->supply.vqmmc)) {
4384 if (enable_vqmmc) {
^^^^^^^^^^^^
4385 ret = regulator_enable(mmc->supply.vqmmc);
^^^^^
4386 host->sdhci_core_to_disable_vqmmc = !ret;
4387 }
"ret" is only initialized when "enable_vqmmc" is true.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200714141410.GB314989@mwanda
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI,
'struct sdhci_iproc_acpi_ids' becomes defined but unused.
Fixes the following W=1 kernel build warning:
mmc/host/sdhci-iproc.c:297:36: warning: ‘sdhci_iproc_acpi_ids’ defined but not used [-Wunused-const-variable=]
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Link: https://lore.kernel.org/r/20200707064701.GC3500@dell
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The variable 'found' is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200706163031.503431-1-colin.king@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cqhci_host_alloc_tdl()'s function header is the only one in
kerneldoc format. Which seems odd as it's not part of an
external API and isn't referenced anywhere else. Seeing as
there has also been no attempt to describe the expected
function arguments either, we're going to assume that this is
not actually a bona fide kerneldoc use-case.
Fixes the following W=1 kernel build warning:
drivers/mmc/host/cqhci.c:163: warning: Function parameter or member 'cq_host' not described in 'cqhci_host_alloc_tdl'
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ritesh Harjani <riteshh@codeaurora.org>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200701124702.908713-15-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
__sdhci_msm_set_clock()'s function header is the only one in
kerneldoc format. Which seems odd as it's not part of an
external API and isn't referenced anywhere else. Seeing as
there has also been no attempt to describe the expected
function arguments either, we're going to assume that this is
not actually a bona fide kerneldoc use-case.
Fixes the following W=1 kernel build warnings:
drivers/mmc/host/sdhci-msm.c:1595: warning: Function parameter or member 'host' not described in '__sdhci_msm_set_clock'
drivers/mmc/host/sdhci-msm.c:1595: warning: Function parameter or member 'clock' not described in '__sdhci_msm_set_clock'
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-14-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Kerneldoc expects arg descriptions to be in the format '@.*: '. If either
the '@' or the ':' is omitted then kerneldoc complains that the description
is missing. Add the missing ':' here and provide a new description for
'value'.
Fixes the following kernel build W=1 warnings:
drivers/mmc/host/sdhci-of-arasan.c:1394: warning: Function parameter or member 'host' not described in 'sdhci_arasan_update_support64b'
drivers/mmc/host/sdhci-of-arasan.c:1394: warning: Function parameter or member 'value' not described in 'sdhci_arasan_update_support64b'
drivers/mmc/host/sdhci-msm.c:1887:6: warning: no previous prototype for ‘sdhci_msm_dump_vendor_regs’ [-Wmissing-prototypes]
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Xiaobo Xie <X.Xie@freescale.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Soeren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-12-lee.jones@linaro.org
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Seeing as sd_wait_data_idle() returns void and only a very specific
read value is checked, there doesn't seem to be a good reason to
check the return value of rtsx_pci_read_register(). So remove
the assignment and definition of 'err'.
Squashes the following W=1 kernel build warning:
drivers/mmc/host/rtsx_usb_sdmmc.c: In function ‘sd_wait_data_idle’:
drivers/mmc/host/rtsx_usb_sdmmc.c:657:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
657 | int err, i;
| ^~~
Cc: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-11-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Seeing as sd_wait_data_idle() returns void and only a very specific
read value is checked, there doesn't seem to be a good reason to
check the return value of rtsx_pci_read_register(). So remove
the assignment and definition of 'err'.
Squashes the following W=1 kernel build warning:
drivers/mmc/host/rtsx_pci_sdmmc.c: In function ‘sd_wait_data_idle’:
drivers/mmc/host/rtsx_pci_sdmmc.c:678:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
678 | int err, i;
| ^~~
Cc: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-10-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Provide missing documentation for dw_mci_exynos_suspend_noirq() and
dw_mci_exynos_resume_noirq() function headers.
Fixes the following W=1 kernel build warnings:
drivers/mmc/host/dw_mmc-exynos.c:184: warning: Function parameter or member 'dev' not described in 'dw_mci_exynos_suspend_noirq'
drivers/mmc/host/dw_mmc-exynos.c:200: warning: Function parameter or member 'dev' not described in 'dw_mci_exynos_resume_noirq'
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20200701124702.908713-9-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'sg_len' and 'dma_conf' are missing correct kerneldoc documentation and
'buf_phys_addr' was misspelled. Correcting these issues fixes the
following W=1 kernel build issues:
mmc/host/atmel-mci.c:352: warning: Function parameter or member 'sg_len' not described in 'atmel_mci'
mmc/host/atmel-mci.c:352: warning: Function parameter or member 'buf_phys_addr' not described in 'atmel_mci'
mmc/host/atmel-mci.c:352: warning: Function parameter or member 'dma_conf' not described in 'atmel_mci'
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-7-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No other function in the file is documented using kerneldoc and no
effort to document the function arguments have been made. It's a
bit of an oddity to say the least. Let's downgrade it from
kerneldoc to a standard comment block instead.
Fixes the following W=1 kernel build warning:
drivers/mmc/host/mtk-sd.c:1030: warning: Function parameter or member 'host' not described in 'msdc_recheck_sdio_irq'
Cc: Chaotian Jing <chaotian.jing@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200701124702.908713-6-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Describe properties; ext_cd_irq, clk_rates and no_divider (x2).
Squashes the following W=1 kernel build warnings:
drivers/mmc/host/sdhci-s3c.c:126: warning: Function parameter or member 'ext_cd_irq' not described in 'sdhci_s3c'
drivers/mmc/host/sdhci-s3c.c:126: warning: Function parameter or member 'clk_rates' not described in 'sdhci_s3c'
drivers/mmc/host/sdhci-s3c.c:126: warning: Function parameter or member 'no_divider' not described in 'sdhci_s3c'
drivers/mmc/host/sdhci-s3c.c:139: warning: Function parameter or member 'no_divider' not described in 'sdhci_s3c_drv_data'
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20200701124702.908713-5-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix sparse build warning:
drivers/mmc/host/sdhci-msm.c:1888:6: warning:
symbol 'sdhci_msm_dump_vendor_regs' was not declared. Should it be static?
Signed-off-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200702020347.77214-1-weiyongjun1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If this controller doesn't issue interrupt for response of command,
this driver lacks to call dma_unmap_sg(). So, fix the issue by
using end() of struct tmio_mmc_dma_ops.
Reported-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Fixes: 2a68ea7896 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1590044466-28372-4-git-send-email-yoshihiro.shimoda.uh@renesas.com
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To add end() operation in the future, clean the code of
renesas_sdhi_internal_dmac_complete_tasklet_fn(). No behavior change.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1590044466-28372-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Related drivers like renesas_sdhi_internal_dmac are possible
to lack dma unmaping in error cases (for example response timeout).
Since tmio_mmc_finish_request() will be always called in any case,
to fix the issue, add end operation into struct tmio_mmc_dma_ops and
call the operation in tmio_mmc_finish_request() to call dma_ummap API
by the related drivers correctly.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1590044466-28372-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On qcom SD host controllers voltage switching be done after the HW
is ready for it. The HW informs its readiness through power irq.
The voltage switching should happen only then.
Use the internal voltage switching and then control the voltage
switching using power irq.
IO-bus supply of eMMC would be kept always-on. So set the load
for this supply to configure it in LPM when eMMC is suspend state
and in HPM when eMMC is active.
Co-developed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Co-developed-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Co-developed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1592919288-1020-4-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If vendor platform drivers are controlling whole logic of voltage
switching, then sdhci driver no need control vqmmc regulator.
So skip enabling/disable vqmmc from SDHC driver.
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1592919288-1020-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
HS400/HS200/eMMC HS doesn't have Preset Value register.
Hence, sdhci_set_ios function overrides the value set by fmw to
SDHCI_CTRL_DRV_TYPE_B.
This patch sets drv_type to MMC_SET_DRIVER_TYPE_A
so that host_control2 register gets updated with the required
strength value.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200623133347.4598-1-akshu.agrawal@amd.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
USDHC of i.MX has internal IC debug register, which record the IC
logical status. So dump these logical status in error condition,
this can help analyzing issue.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1592985830-13038-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for writing new clkbuf_sel property for the J721e 4 bit IP.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-7-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For speed modes where DLL is not enabled write to TXDLYCLK to enable
transmitter delay chain mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-6-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The clock > CLOCK_TOO_SLOW_HZ condition gating phy configuration
is only required because dll should not be enabled at too low a
clock frequency or too low timing. Make sure that this condition
only gates dll enablement.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-5-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Support for AM65x PG2.0. Use the SoC bus framework to fixup
the driver data and skip do DLL calibration if the revision is 1.0
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-4-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB flag
to indicate the same.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-3-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"K" stands for "kelvin".
While at it, make the spacing before units consistent.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200618080321.16678-1-geert+renesas@glider.be
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds datactrl_mask_sdio for sdmmc revisions.
sdmmc revisions used same bit of previous ST variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200611132839.4515-1-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These functions do not check the return value of devm_clk_register():
- sdhci_arasan_register_sdcardclk()
- sdhci_arasan_register_sampleclk()
Therefore, add the missed checks to fix them.
Fixes: c390f2110a ("mmc: sdhci-of-arasan: Add ability to export card clock")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200608162226.3259186-1-hslester96@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Interconnect bandwidth scaling support is now added as a
part of OPP. So, make sure interconnect driver is ready
before handling interconnect scaling.
Signed-off-by: Pradeep P V K <ppvk@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1591691846-7578-2-git-send-email-ppvk@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When calculating the clock divider, start dividing at 2 instead of 1.
The divider is divided by two at the end of the calculation, so starting
at 1 may result in a divider of 0, which shouldn't happen.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200709195706.12741-3-eajames@linux.ibm.com
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to support new chip rts5228, the definitions of some internal
registers and workflow have to be modified.
Added rts5228.c rts5228.h for independent functions of the new chip rts5228
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20200706070259.32565-1-ricky_wu@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During DLL initialization, the DLL_CONFIG register value would be
updated with the value supplied from the device-tree.
Override this register only if a valid value is supplied.
Fixes: 03591160ca ("mmc: sdhci-msm: Read and use DLL Config property from device tree file")
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1594213888-2780-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The actual max_segs computation leads to failure while using the broadcom
sdio brcmfmac/bcmsdh driver, since the driver tries to make usage of
scatter gather.
But with the dram-access-quirk we use a 1,5K SRAM bounce buffer, and the
max_segs current value of 3 leads to max transfers to 4,5k, which doesn't
work.
This patch sets max_segs to 1 to better describe the hardware limitation,
and fix the SDIO functionality with the brcmfmac/bcmsdh driver on Amlogic
G12A/G12B SoCs on boards like SEI510 or Khadas VIM3.
Reported-by: Art Nikpal <art@khadas.com>
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Fixes: acdc8e71d9 ("mmc: meson-gx: add dram-access-quirk")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200608084458.32014-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
function that isn't used anymore. Otherwise the main new thing for the common
clk framework is that it is selectable in the Kconfig language now. Hopefully
this will let clk drivers and clk consumers be testable on more than the
architectures that support the clk framework. The goal is to introduce some
Kunit tests for the framework.
Outside of the core framework we have the usual set of various driver updates
and non-critical fixes. The dirstat shows that the new Baikal-T1 driver is the
largest addition this time around in terms of lines of code. After that the x86
(Intel), Qualcomm, and Mediatek drivers introduce many lines to support new or
upcoming SoCs. After that the dirstat shows the usual suspects working on their
SoC support by fixing minor bugs, correcting data and converting some of their
DT bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix clock support
on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and clk-pllv3
drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support aarch32 mode on
aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using composite
clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102 defined
bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+
-----BEGIN PGP SIGNATURE-----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=nuG5
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time around we have four lines of diff in the core framework,
removing a function that isn't used anymore. Otherwise the main new
thing for the common clk framework is that it is selectable in the
Kconfig language now. Hopefully this will let clk drivers and clk
consumers be testable on more than the architectures that support the
clk framework. The goal is to introduce some Kunit tests for the
framework.
Outside of the core framework we have the usual set of various driver
updates and non-critical fixes. The dirstat shows that the new
Baikal-T1 driver is the largest addition this time around in terms of
lines of code. After that the x86 (Intel), Qualcomm, and Mediatek
drivers introduce many lines to support new or upcoming SoCs. After
that the dirstat shows the usual suspects working on their SoC support
by fixing minor bugs, correcting data and converting some of their DT
bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix
clock support on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and
clk-pllv3 drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support
aarch32 mode on aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using
composite clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102
defined bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on
Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (155 commits)
clk: mediatek: Remove ifr{0,1}_cfg_regs structures
clk: baikal-t1: remove redundant assignment to variable 'divider'
clk: baikal-t1: fix spelling mistake "Uncompatible" -> "Incompatible"
dt-bindings: clock: Add a missing include to MMP Audio Clock binding
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
clk: clk-si5341: Add support for the Si5345 series
...
Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzkHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yldOwCgus/DgpnI1UL4z+NdBxJrAXtkPmgAn2sgTUea
i5RblCmcVMqvHaGtYkY+
=tScN
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (233 commits)
habanalabs: correctly cast u64 to void*
habanalabs: initialize variable to default value
extcon: arizona: Fix runtime PM imbalance on error
extcon: max14577: Add proper dt-compatible strings
extcon: adc-jack: Fix an error handling path in 'adc_jack_probe()'
extcon: remove redundant assignment to variable idx
w1: omap-hdq: print dev_err if irq flags are not cleared
w1: omap-hdq: fix interrupt handling which did show spurious timeouts
w1: omap-hdq: fix return value to be -1 if there is a timeout
w1: omap-hdq: cleanup to add missing newline for some dev_dbg
/dev/mem: Revoke mappings when a driver claims the region
misc: xilinx-sdfec: convert get_user_pages() --> pin_user_pages()
misc: xilinx-sdfec: cleanup return value in xsdfec_table_write()
misc: xilinx-sdfec: improve get_user_pages_fast() error handling
nvmem: qfprom: remove incorrect write support
habanalabs: handle MMU cache invalidation timeout
habanalabs: don't allow hard reset with open processes
habanalabs: GAUDI does not support soft-reset
habanalabs: add print for soft reset due to event
habanalabs: improve MMU cache invalidation code
...
Clear tuning_done flag while executing tuning to ensure vendor
specific HS400 settings are applied properly when the controller
is re-initialized in HS400 mode.
Without this, re-initialization of the qcom SDHC in HS400 mode fails
while resuming the driver from runtime-suspend or system-suspend.
Fixes: ff06ce4178 ("mmc: sdhci-msm: Add HS400 platform support")
Cc: stable@vger.kernel.org
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1590678838-18099-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When enabling calibration at reset, the CALCR register was completely
rewritten. This may cause certain bits being deleted unintentedly.
Fix by issuing a read-modify-write operation.
Fixes: 727d836a37 ("mmc: sdhci-of-at91: add DT property to enable calibration on full reset")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20200527105659.142560-1-eugen.hristev@microchip.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In current code, we add 1ms dealy after each tuning command for standard
tuning method. Adding this 1ms dealy is because USDHC default check the
CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning
IC logic do not wait for the tuning data sending out by the card, trigger
the buffer read ready interrupt immediately, and step to next cycle. So
when next time the new tuning command send out by USDHC, card may still
not send out the tuning data of the upper command，then some eMMC cards
may stuck, can't response to any command, block the whole tuning procedure.
If do not check the CMD CRC for tuning, then do not has this issue. USDHC
will wait for the tuning data of each tuning command and check them. If the
tuning data pass the check, it also means the CMD line also okay for tuning.
So this patch disable the CMD CRC check for tuning, save some time for the
whole tuning procedure.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1590488522-9292-2-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According the RM, the bit[6~0] of register ESDHC_TUNING_CTRL is
TUNING_START_TAP, bit[7] of this register is to disable the command
CRC check for standard tuning. So fix it here.
Fixes: d87fc96636 ("mmc: sdhci-esdhc-imx: support setting tuning start point")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1590488522-9292-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When use the specific GPIO to detect the card insert/remove, we can
also add the GPIO as a wakeup source. When system suspend, insert or
remove the card can wakeup the system.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1590547175-15070-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
WARNING: CPU: 1 PID: 85 at kernel/dma/debug.c:1302
debug_dma_map_sg+0x2a0/0x3cc mmci-pl18x 58005000.sdmmc: DMA-API: mapping sg
segment longer than device claims to support [len=126976] [max=65536]
dma api debug checks and compares the segment size to dma_get_max_seg_size
(dev->dma_parms->max_segment_size), the sdmmc variant has an internal DMA
and should define its max_segment_size constraint to avoid this warning.
This Patch defines the dev->dma_parms->max_segment_size with the constraint
already set for mmc core (host->mmc->max_seg_size).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200526155103.12514-3-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
WARNING: CPU: 1 PID: 20 at kernel/dma/debug.c:500 add_dma_entry+0x16c/0x17c
DMA-API: exceeded 7 overlapping mappings of cacheline 0x031d2645
Modules linked in:
CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 5.5.0-rc2-00021-gdeda30999c2b-dirty #49
Hardware name: STM32 (Device Tree Support)
Workqueue: events_freezable mmc_rescan
[<c03138c0>] (unwind_backtrace) from [<c030d760>] (show_stack+0x10/0x14)
[<c030d760>] (show_stack) from [<c0f2eb28>] (dump_stack+0xc0/0xd4)
[<c0f2eb28>] (dump_stack) from [<c034a14c>] (__warn+0xd0/0xf8)
[<c034a14c>] (__warn) from [<c034a530>] (warn_slowpath_fmt+0x94/0xb8)
[<c034a530>] (warn_slowpath_fmt) from [<c03bca0c>] (add_dma_entry+0x16c/0x17c)
[<c03bca0c>] (add_dma_entry) from [<c03bdf54>] (debug_dma_map_sg+0xe4/0x3d4)
[<c03bdf54>] (debug_dma_map_sg) from [<c0d09244>] (sdmmc_idma_prep_data+0x94/0xf8)
[<c0d09244>] (sdmmc_idma_prep_data) from [<c0d05a2c>] (mmci_prep_data+0x2c/0xb0)
[<c0d05a2c>] (mmci_prep_data) from [<c0d073ec>] (mmci_start_data+0x134/0x2f0)
[<c0d073ec>] (mmci_start_data) from [<c0d078d0>] (mmci_request+0xe8/0x154)
[<c0d078d0>] (mmci_request) from [<c0cecb44>] (mmc_start_request+0x94/0xbc)
DMA api debug brings to light leaking dma-mappings, dma_map_sg and
dma_unmap_sg are not correctly balanced.
If a request is prepared, the dma_map/unmap are done in asynchronous call
pre_req (prep_data) and post_req (unprep_data). In this case the
dma-mapping is right balanced.
But if the request was not prepared, the data->host_cookie is define to
zero and the dma_map/unmap must be done in the request. The dma_map is
called by mmci_dma_start (prep_data), but there is no dma_unmap in this
case.
This patch adds dma_unmap_sg when the dma is finalized and the data cookie
is zero (request not prepared).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200526155103.12514-2-ludovic.barre@st.com
Fixes: 46b723dd86 ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel Keem Bay SoC eMMC/SD/SDIO controller is based on
Arasan SD 3.0 / eMMC 5.1 host controller IP.
However, it does not support 64-bit access as its AXI interface
has 32-bit address ports.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200526062758.17642-3-wan.ahmad.zainie.wan.mohamad@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Accordingly to Cadence documentation, PHY write procedure is:
1. Software sets the PHY Register Address (HRS04[5:0]) and the
PHY Write Data (HRS04[15:8]) fields.
2. Software sets the PHY Write Transaction Request (HRS04[24]) field to 1.
3. Software waits as the PHY Write Transaction Acknowledge (HRS04[26])
field is equal to 0.
4. Hardware performs the write transaction to PHY register where
HRS04[15:8] is a data written to register under HRS04[5:0] address.
5. Hardware sets the PHY Transaction Acknowledge (HRS04[26]) to 1 when
transaction is completed.
6. Software clears the PHY Write Transaction Request (HRS04[24]) to 1
after noticing that the PHY Write Transaction Acknowledge (HRS04[26])
field is equal to 1.
7. Software waits for the PHY Acknowledge Register (HRS04[26]) field is
equal to 0.
Add missing steps 3 and 7. Lack of these steps causes
integrity errors detested by hardware.
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Link: https://lore.kernel.org/r/20200525074053.7309-1-vladimir.kondratiev@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC HS400 timing requires many specific registers setting,
unlike other speed modes which need to set only host controller 2
register. When driver needs to downgrade HS400 mode to other speed
mode, the controller have to exit HS400 timing properly first.
This patch is to support the procedure of HS400 exiting at the
beginning of esdhc_set_uhs_signaling.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200522031256.856-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement dump_vendor_registers host operation to print the
vendor specific registers in addition to standard SDHC
register during error conditions.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590139950-7288-9-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce new sdhci ops to dump vendor specific registers in the
sdhci_dumpregs during error.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590139950-7288-8-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain platforms require different settings in the
SDCC_HC_REG_DLL_CONFIG register. This setting can change from platform
to platform. So the driver should check whether a particular platform
require a different setting by reading the DT file and use it.
Also use msm_cm_dll_set_freq only when DLL not supplied.
Signed-off-by: Bao D. Nguyen <nguyenb@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590139950-7288-7-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain platforms require different settings in the
SDCC_HC_REG_DDR_CONFIG register. This setting can change from platform
to platform. So the driver should check whether a particular platform
require a different setting by reading the device tree file and use it.
Signed-off-by: Bao D. Nguyen <nguyenb@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590139950-7288-6-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update dll_config_3 as per the host clock frequency as specified in the
DLL Hardware Reference Guide.
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590139950-7288-5-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With SDCC v5.1.0, additional setting needed for enabling DLL output.
The dll-user-control register need to be configured during dll
initialization for getting proper dll output.
Without this configuration, we don't get the DLL lock status properly.
Also update the DLL register settings according to the SDCC Hardware
Programming Guide.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590139950-7288-4-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When auto calibration timeouts, calibration is disabled and fail-safe
drive strength values are programmed based on the signal voltage.
Different fail-safe drive strength values based on voltage are
applicable only for SoCs supporting 3V3 and 1V8 pad controls.
So, this patch avoids reading these properties from the device tree
for SoCs not using pad controls and the warning of missing properties
will not show up on these SoC platforms.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590005337-1087-1-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the tmio device is attached to a genpd (PM domain), that genpd may have
->start|stop() callback assigned to it. To make sure the device is
accessible during ->probe(), genpd's ->start() callback must be invoked,
which is currently managed by tmio_mmc_host_probe(). However, it's likely
that may be too late for some cases, as registers may be read and written
way before that point.
To fix the behaviour, let's move the call to dev_pm_domain_start() from
tmio_mmc_host_probe() into those clients that needs it. From discussions at
linux-mmc mailing list, it turned out that it should be sufficient to do
this for the SDHI renesas variants, hence the call is move to
renesas_sdhi_probe().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20200519152445.6922-1-ulf.hansson@linaro.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Before calling tmio_mmc_host_probe(), the caller is required to enable
clocks for its device, as to make it accessible when reading/writing
registers during probe.
Therefore, the responsibility to disable these clocks, in the error path of
->probe() and during ->remove(), is better managed outside
tmio_mmc_host_remove(). As a matter of fact, callers of
tmio_mmc_host_remove() already expects this to be the behaviour.
However, there's a problem with tmio_mmc_host_remove() when the Kconfig
option, CONFIG_PM, is set. More precisely, tmio_mmc_host_remove() may then
disable the clock via runtime PM, which leads to clock enable/disable
imbalance problems, when the caller of tmio_mmc_host_remove() also tries to
disable the same clocks.
To solve the problem, let's make sure tmio_mmc_host_remove() leaves the
device with clocks enabled, but also make sure to disable the IRQs, as we
normally do at ->runtime_suspend().
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200519152434.6867-1-ulf.hansson@linaro.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
This driver has been developed as a separate module starting
from the similar sdhci-esdhc-imx.c.
Reasons for a separate sdchi-esdhc-mcf driver:
- m68K architecture does not support devicetrees, so modifying
sdhci-of-esdhc.c that is devicetree-related adding platform data
seems not appropriate,
- clock-related part, has to be implemented specifically for
mcf5441x family (see esdhc_mcf_pltfm_set_clock()),
- this is a big endian cpu accessing a big endian controller,
but about sdma, this controller does not support hw swap, which
needs to be handled with specific code,
- some other minor differences but mainly to avoid risks on
tweaking inside largely used imx driver. Adding just a small
size ColdFire-specific driver, with benefits in a further less
risky maintenance.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200518191742.1251440-3-angelo.dureghello@timesys.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controller as the ColdFire eshdc may require an endianness
byte swap, because DMA read endianness is not configurable.
Facilitate using the bounce buffer for this by adding
->copy_to_bounce_buffer().
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200518191742.1251440-2-angelo.dureghello@timesys.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Kbuild test robot reports the following warning in lines 56 and 87 of
drivers/mmc/host/meson-mx-sdhc-clkc.c:
Using plain integer as NULL pointer
Drop the integer value from the struct initialization to fix that
warning. This will still ensure that the compiler will zero out the
struct so it's in a well-defined state.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200517222907.1277787-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For Meson8 and Meson8b SoCs the vendor driver follows the following
pattern:
- for eMMC and SD cards in .set_pdma it sets:
pdma->rxfifo_manual_flush = 1;
- for SDIO cards in .set_pdma it sets:
pdma->rxfifo_manual_flush = 0;
- before syncing the DMA read buffer is sets:
pdma->rxfifo_manual_flush |= 0x02;
Set the second bit of MESON_SDHC_PDMA_RXFIFO_MANUAL_FLUSH without
clearing the first bit before syncing the DMA read buffer. This fixes a
problem where Meson8 and Meson8b SoCs would read random garbage from SD
cards. It is not clear why it worked for eMMC cards. This manifested in
the following errors when plugging in an SD card:
unrecognised SCR structure version <random number>
Cc: Thomas Graichen <thomas.graichen@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200517222907.1277787-1-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For an x86_64 allmodconfig build Stephen reports that building
meson-mx-sdhc-clkc.o warns that MODULE_LICENSE is missing and when
linking meson_mx_sdhc_register_clkc cannot be found.
Compile the MMC controller driver together with the build-in clock
controller driver into one module rather than using two separate
modules to fix these issues.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200518060811.1499962-1-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need a different set_uhs_signaling implementation for
MMC_TIMING_MMC_HS and MMC_TIMING_MMC_HS400.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200513182602.3636a551@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHC MMC host controller on Amlogic SoCs provides an eMMC and MMC
card interface with 1/4/8-bit bus width.
It supports eMMC spec 4.4x/4.5x including HS200 (up to 100MHz clock).
The public S805 datasheet [0] contains a short documentation about the
registers. Unfortunately it does not describe how to use the registers
to make the hardware work. Thus this driver is based on reading (and
understanding) the Amlogic 3.10 GPL kernel code.
Some hardware details are not easy to see. Jianxin Pan was kind enough
to answer my questions:
The hardware has built-in busy timeout support. The maximum timeout is
30 seconds. This is only documented in Amlogic's internal
documentation.
The controller only works with very specific clock configurations. The
details are not part of the public datasheet. In my own words the
supported configurations are:
- 399.812kHz: clkin = 850MHz div = 2126 sd_rx_phase = 63
- 1MHz: clkin = 850MHz div = 850 sd_rx_phase = 55
- 5.986MHz: clkin = 850MHz div = 142 sd_rx_phase = 24
- 25MHz: clkin = 850MHz div = 34 sd_rx_phase = 15
- 47.222MHz: clkin = 850MHz div = 18 sd_rx_phase = 11/15 (SDR50/HS)
- 53.125MHz: clkin = 850MHz div = 16 sd_rx_phase = (tuning)
- 70.833MHz: clkin = 850MHz div = 12 sd_rx_phase = (tuning)
- 85MHz: clkin = 850MHz div = 10 sd_rx_phase = (tuning)
- 94.44MHz: clkin = 850MHz div = 9 sd_rx_phase = (tuning)
- 106.25MHz: clkin = 850MHz div = 8 sd_rx_phase = (tuning)
- 127.5MHz: clkin = 1275MHz div = 10 sd_rx_phase = (tuning)
- 141.667MHz: clkin = 850MHz div = 6 sd_rx_phase = (tuning)
- 159.375MHz: clkin = 1275MHz div = 8 sd_rx_phase = (tuning)
- 212.5MHz: clkin = 1275MHz div = 6 sd_rx_phase = (tuning)
- (sd_tx_phase is always 1, 94.44MHz is not listed in the datasheet
but this is what the 3.10 BSP kernel on Odroid-C1 actually uses)
NOTE: CMD23 support is disabled for now because it results in command
timeouts and thus decreases read performance.
Tested-by: Wei Wang <lnykww@gmail.com>
Tested-by: Xin Yin <yinxin_1989@aliyun.com>
Reviewed-by: Xin Yin <yinxin_1989@aliyun.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200512204147.504087-3-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use FIELD_GET and FIELD_PREP to get access to the register fields. Delete
the shift macros and use GENMASK() for the touched macros.
Note that, this has the side-effect of changing the constants to 64-bit on
64-bit platforms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20200511062828.1791484-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, tmio_mmc_irq() handler is registered before the host is
fully initialized by tmio_mmc_host_probe(). I did not previously notice
this problem.
The boot ROM of a new Socionext SoC unmasks interrupts (CTL_IRQ_MASK)
somehow. The handler is invoked before tmio_mmc_host_probe(), then
emits noisy call trace.
Move devm_request_irq() below tmio_mmc_host_probe().
Fixes: 3fd784f745 ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200511062158.1790924-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GL9763E supports High Speed SDR, High Speed DDR, HS200, HS400, Enhanced
Strobe in HS400 mode, 1/4/8 bits data bus and 3.3/1.8V.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20200508064154.13473-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC_CAP_ERASE bit is no longer used by the mmc core as erase, discard
and trim operations are now always supported. Therefore, drop the bit and
move all mmc hosts away from using it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Link: https://lore.kernel.org/r/20200508112902.23575-1-ulf.hansson@linaro.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Using a fixed 1s polling timeout for all commands is a bit problematic.
For some commands it means waiting longer than needed for the polling to be
aborted, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
1s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Note that, even if the sdricoh_cs driver may currently not support HW busy
detection on DAT0, some comments in the code refer to that the HW may
support it. Therefore, it seems better to be proactive in this case.
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508095228.14230-1-ulf.hansson@linaro.org
Rather than to poll in a busy-loop, let's convert into using
read_poll_timeout() and insert a small delay between each polling attempts.
In particular, this avoids hogging the CPU.
Additionally, to convert to read_poll_timeout() we also need to switch from
using a specific number of polling attempts, into a specific timeout in us
instead. The previous 100000 attempts, is translated into a total timeout
of total 1s, as that seemed like reasonable value to pick.
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508095218.14177-1-ulf.hansson@linaro.org
Rather than to poll in a busy-loop, let's convert into using
read_poll_timeout() and insert a small delay between each polling attempts.
In particular, this avoids hogging the CPU.
Additionally, to convert to read_poll_timeout() we also need to switch from
using a specific number of polling attempts, into a specific timeout in us
instead. The previous 100000 attempts, is translated into a total timeout
of total 1s, as that seemed like reasonable value to pick.
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508095210.14123-1-ulf.hansson@linaro.org
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
~2s timeout of the polling loop, implemented in cb710_wait_for_event(). In
this way, we let the mmc core validate the needed timeout, which may lead
to that it converts from a R1B into a R1 response and then use CMD13 to
poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 2s, like erase (CMD38) for example.
Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-7-ulf.hansson@linaro.org
The 'pengutronix' address is defunct for years. Use the proper contact
address.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200502142840.19418-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even though specifying OPP's in device tree is optional, ignoring all errors
reported by dev_pm_opp_of_add_table() means we can't distinguish between a
missing OPP table and a wrong/buggy OPP table. While missing OPP table
(dev_pm_opp_of_add_table() returns a -ENODEV in such case) can be ignored,
a wrong/buggy OPP table in device tree should make the driver error out.
while we fix that, lets also fix the variable names for opp/opp_table to
avoid confusion and name them opp_table/has_opp_table instead.
Suggested-by: Matthias Kaehlcke <matthias@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1588080785-6812-10-git-send-email-rnayak@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With R-Car Gen3, CRC error occue at the following TAPs.
H3, M3W 1.3, M3N... TAP=2,3,6,7
M3W 3.0 ... TAP=1,3,5,7
(Note: for 4tap SoCs, the numbers get divided by 2)
Do not use these TAPs in HS400, and also don't use auto correction but
manual correction.
We check for bad taps in two places:
1) After tuning HS400: Then, we select a neighbouring TAP. One of them
must be good, because there are never three bad taps in a row.
Retuning won't help because we just finished tuning.
2) After a manual correction request: Here, we can't switch to the
requested TAP. But we can retune (if the HS200 tuning was good)
because the environment might have changed since the last tuning.
If not, we stay on the same TAP.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: refactored to match upstream driver, reworded commit msg]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200423130432.9990-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For ES1.2, add a comment explaining the situation. For ES1.3 (and
later, although unlikely), add a new entry defining it as 4tap.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200423130432.9990-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using a fixed 3s polling timeout for all commands with R1B responses is a
bit problematic.
For some commands it means waiting longer than needed for the polling to be
aborted, which may not a big issue, but still. For other commands, like for
an erase (CMD38), may require longer timeouts than 3s. In these cases, we
may end up treating the command as it failed, while it just needed some
more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-19-ulf.hansson@linaro.org
Clarify the use of r1b_timeout, by renaming it to MMC_SPI_R1B_TIMEOUT_MS
and by dropping the corresponding confusing comment about it.
Additionally, let's also add a new define, MMC_SPI_INIT_TIMEOUT_MS and use
it during the initialization. Even if these two defines are given the same
value, the split makes it easier to understand them.
Cc: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-18-ulf.hansson@linaro.org
Using a fixed 1s timeout for all commands (and data transfers) is a bit
problematic.
For some commands it means waiting longer than needed for the timer to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
1s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-17-ulf.hansson@linaro.org
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
1s timeout used by tifm_sd. In this way, we let the mmc core validate the
needed timeout, which may lead to that it converts from a R1B into a R1
response and then use CMD13 to poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 1s, like erase (CMD38) for example.
Cc: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-16-ulf.hansson@linaro.org
The in-parameter timeout is always set to TRANSFER_TIMEOUT by the callers
of sdricoh_query_status(), hence let's drop it.
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-12-ulf.hansson@linaro.org
For commands that doesn't involve to prepare a data transfer, owl-mmc is
using a fixed 30s response timeout. This is a bit problematic.
For some commands it means waiting longer than needed for the completion to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
30s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-8-ulf.hansson@linaro.org
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
5s timeout used by jz4740. In this way, we let the mmc core validate the
needed timeout, which may lead to that it converts from a R1B into a R1
response and then use CMD13 to poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 5s, like erase (CMD38) for example.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-5-ulf.hansson@linaro.org
Fix the following sparse warning:
drivers/mmc/host/sdhci-pci-o2micro.c:497:6: warning: symbol
'sdhci_pci_o2_set_clock' was not declared. Should it be static?
drivers/mmc/host/sdhci-pci-o2micro.c:512:5: warning: symbol
'sdhci_pci_o2_probe_slot' was not declared. Should it be static?
drivers/mmc/host/sdhci-pci-o2micro.c:581:5: warning: symbol
'sdhci_pci_o2_probe' was not declared. Should it be static?
drivers/mmc/host/sdhci-pci-o2micro.c:786:5: warning: symbol
'sdhci_pci_o2_resume' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587624199-96926-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If sdhci-of-at91.c is compiled without CONFIG_HAVE_CLK, the line
caps1 |= FIELD_PREP(SDHCI_CLOCK_MUL_MASK, clk_mul);
... emits "FIELD_PREP: value too large for the field" warning.
The compiler seems to decide clk_mul is constant (unsigned int)-1,
because clk_get_rate() returns 0 when CONFIG_HAVE_CLK is disabled.
Add HAVE_CLK to the depenency since this driver does not work without
the clock APIs anyway.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20200422153401.7913-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
After TAP refactorization, we can use 'unsigned int' for two more
variables because all the calculations work on this type now.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200420170230.9091-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fix a power-on issue, and avoid to retry the power sequence.
In power off sequence: sdmmc must set pwr_reg in "power-cycle" state
(value 0x2), to prevent the card from being supplied through the signal
lines (all the lines are driven low).
In power on sequence: when the power is stable, sdmmc must set pwr_reg
in "power-off" state (value 0x0) to drive all signal to high before to
set "power-on".
To avoid writing the same value to the power register several times, this
register is cached by the pwr_reg variable. At probe pwr_reg is initialized
to 0 by kzalloc of mmc_alloc_host.
Like pwr_reg value is 0 at probing, the power on sequence fail because
the "power-off" state is not writes (value 0x0) and the lines
remain drive to low.
This patch initializes "pwr_reg" variable with power register value.
This it done in sdmmc variant init to not disturb default mmci behavior.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200420161831.5043-1-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some qualcomm SoCs we need to vote on a performance state of a power
domain depending on the clock rates. Hence move to using OPP api to set
the clock rate and performance state specified in the OPP table.
On platforms without an OPP table, dev_pm_opp_set_rate() is eqvivalent to
clk_set_rate()
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1587132279-27659-10-git-send-email-rnayak@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
4s timeout used by usdhi6rol0. In this way, we let the mmc core validate
the needed timeout, which may lead to that it converts from a R1B into a R1
response and then use CMD13 to poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 4s, like erase (CMD38) for example.
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Lars Persson <lars.persson@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Link: https://lore.kernel.org/r/20200414161413.3036-6-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using a fixed 2s timeout for all commands is a bit problematic.
For some commands it means waiting longer than needed for the timer to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
2s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200414161413.3036-4-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting the timer on a per request basis, is rather limiting as the timer
really depends on what commands that is to be sent as part of the request.
Therefore improve the behaviour by programming the timer per command basis
instead.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200414161413.3036-3-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When atmci_request_end() is about to finish a request for one slot, there
is a possibility that there is new request queued for another slot. If this
turns out to be the case, the new request is started and the timer is
re-programmed for it.
Although, a few lines below in atmci_request_end(), this timer becomes
deleted, likely corresponding to the other recently completed request. This
looks wrong, so let's fix it.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200414161413.3036-2-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ADMA_ERR_SIZE_EN bit of VENDOR_SPECIFIC_FUNC register controls
ADMA length mismatch error interrupt. Enable it by default.
And update all bit shift defines with BIT macro.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-4-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-msm can support auto cmd12.
So enable SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 quirk.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-3-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When use one SDIO wifi which enable the runtime PM feature on i.MX6SX,
we meet system hang. This hang happened during the usdhc runtime resume,
in sdhci_init(), when call the sdhci_set_default_irqs. One interrupt
(SDHCI_INT_CARD_INT) triggered just after the host->ier update and before
the write of register SDHCI_SIGNAL_ENABLE. So in sdhci_irq, it will skip
the call of sdio_signal_irq() because current host->ier do not set the
SDHCI_INT_CARD_INT. So this SDIO wifi interrupt always keep triggered,
let the system stuck in irq handle, can't response any other thread.
This patch add spin lock for the sdhci_set_default_irqs to fix this issue.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1586941255-9237-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the request_atomic() API for nonremovable cards, that means
we can submit next request in the irq hard handler context to reduce
latency.
Moreover factor out the AUTO CMD23 checking into a separate function
to reduce duplicate code.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/60142fe6c6c1dbba2696e775564ae2166786f0bc.1586744073.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the request_atomic() ops for the sdhci driver to process
one request in the atomic context if the card is nonremovable.
Moreover, we should return BUSY flag if controller has not released
the inhibit bits to allow HSQ trying to send request again in non-atomic
context.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/9ed34afa9fb42e0c234065cac5401d7826942b55.1586744073.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD host controller can process one request in the atomic context if
the card is nonremovable, which means we can submit next request in the
irq hard handler when using the MMC host software queue to reduce the
latency. Thus this patch adds a new API request_atomic() for the host
controller, as well as adding support for host software queue to submit
a request by the new request_atomic() API.
Moreover there is an unusual case that the card is busy when trying to
send a command, and we can not polling the card status in interrupt
context by using request_atomic() to dispatch requests. Thus we should
queue a work to try again in the non-atomic context in case the host
releases the busy signal later.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/a344e27e506cb2329073cbd5cf65e15cc3cbeba9.1586744073.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Spending time under spinlock increases IRQ latencies and also
response times because preemption is disabled.
sdhci_send_command() waits up to 10 ms under spinlock for inhibit bits
to clear. In general inhibit bits will not be set, but there may be
corner cases, especially in the face of errors, where waiting helps.
There might also be dysfunctional hardware that needs the waiting. So
retain the legacy behaviour but do not wait for inhibit bits while under
spinlock. Instead adjust the logic to enable waiting while not under
spinlock. That is mostly straight forward, but in the interrupt handler
it requires deferring an "inhibited" command to the IRQ thread where
sleeping is allowed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for further changes, tidy sdhci_request() a bit.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-5-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_finish_data() is defined before it is referenced, so forward
declaration is not necessary.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-4-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_send_command() has not been used outside of sdhci.c for many
years. Stop exporting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add 2 helper functions to make the use of the auto-CMD23 flag more
readable.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of reimplementing the logic in mmc_regulator_set_vqmmc(), use the
mmc code function directly.
This also allows us to fix a related issue on STM32MP1, when a voltage
switch of 1.8V is done for the eMMC, but the current level is already set
to 1.8V. More precisely, in this scenario the call to the
->post_sig_volt_switch() hangs, indefinitely waiting for the voltage switch
to complete. Fix this problem by checking if mmc_regulator_set_vqmmc()
returned 1 and then skip invoking the callback.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-3-marex@denx.de
[Ulf: Updated the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Patch all drivers which use mmc_regulator_set_vqmmc() and prepare them for
the fact that mmc_regulator_set_vqmmc() can return a value > 0, which would
happen if the signal voltage switch did NOT happen, because the voltage was
already set correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-1-marex@denx.de
[Ulf: Re-worked/simplified the code a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clang warns:
drivers/mmc/host/sdhci-of-arasan.c:784:9: warning: variable 'ret' is
uninitialized when used here [-Wuninitialized]
return ret;
^~~
drivers/mmc/host/sdhci-of-arasan.c:738:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
drivers/mmc/host/sdhci-of-arasan.c:860:9: warning: variable 'ret' is
uninitialized when used here [-Wuninitialized]
return ret;
^~~
drivers/mmc/host/sdhci-of-arasan.c:810:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
2 warnings generated.
This looks like a copy paste error. Neither function has handling that
needs ret so just remove it and return 0 directly.
Link: https://github.com/ClangBuiltLinux/linux/issues/996
Reported-by: kernelci.org bot <bot@kernelci.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20200416182402.16858-1-natechancellor@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No need to call platform_get_resource twice when we still have the
pointer from before. Also, use '%pa' for a resource_size_t pointer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200408142252.21958-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
When tuning HS400, if all TAPS are good, we can utilize the SMPCMP
register to select the optimal TAP. For that, we populate a second
bitmap with SMPCMP results and query it in case the regular bitmap is
full (= all good).
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200408094638.10375-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The comment and the define about how TAPs are selected were confusing to
me because the good TAP was only valid if it was bigger than a *_MAX_*
value. Rename the define and adapt the comment to what really happens.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200408094638.10375-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To select the best TAP, we need to find the longest stream of set bits
in a bit field. There is now a helper function for bitmaps which
iterates over all region of set bits. Using it makes the code much more
concise and easier to understand. Double so, because we need to handle
two bitmaps in the near future. Remove a superfluous comment while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200408094638.10375-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use FIELD_GET and FIELD_PREP to get access to the register fields. Delete
the shift macros and use GENMASK() for the touched macros.
Note that, this has the side-effect of changing the constants to 64-bit on
64-bit platforms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200408072105.422-2-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the SDHCI specification, the Capabilities Register (Offset 0x40h)
is the 64-bit width register, but in Linux, it is represented as two
registers, SDHCI_CAPABILITIES and SDHCI_CAPABILITIES_1 so that drivers
can use 32-bit register accessors.
The upper 32-bit field is associated with SDHCI_CAPABILITIES_1.
Move the definition of SDHCI_CAPABILITIES_1 to the correct place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200408072105.422-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI clock operations are platform specific. So it better to define
them separately for particular platform. This will prevent multiple
if..else conditions and will make it easy for user to add their own
clock operations handlers.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1586195015-128992-6-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Existing driver code has the platform specific structures scattered
throughout the driver code. Rearrange the platform specific data
structures for more modularity and readability. This will help in adding
new static functions with more ease.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1586195015-128992-5-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is 'struct sdhci_arasan_data' but also
'struct sdhci_arasan_of_data sdhci_arasan_data'. Rename the latter to
avoid confusion with the name of the struct.
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1586195015-128992-4-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support to set tap delays for Xilinx Versal SD controller. The tap
delay registers have moved to SD controller space in Versal. Make the
changes accordingly.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1586195015-128992-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The in-parameter struct mmc_data *data is never NULL, because the caller
always provides a valid pointer. Hence drop the corresponding redundant
code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200407143903.22477-1-ulf.hansson@linaro.org
The in-parameter "wait" is always set to 0 by the caller, hence just drop
it and its corresponding code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Link: https://lore.kernel.org/r/20200406114337.8802-1-ulf.hansson@linaro.org
The MMC_CAP_ERASE and MMC_CAP_CMD23 flags are already being set in the
common sdhci_setup_host(). This makes it redundant to set them for
sdhci-sprd, so let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200406113724.8504-1-ulf.hansson@linaro.org
Instead of explicitly checking for SDIO specific requests and then
returning an error code, let's set MMC_CAP2_NO_SDIO to tell the mmc core to
prevent them altogether.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200401145531.23247-1-ulf.hansson@linaro.org
Previous to commit 511ce378e1 ("mmc: Add MMC host software queue
support"), removing MMC_CAP2_CQE was enough to disable command queuing, but
now the cqe_ops must also be NULL otherwise ->cqe_enable() will be
called. Fix SDHCI_QUIRK_BROKEN_CQE to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 511ce378e1 ("mmc: Add MMC host software queue support")
Link: https://lore.kernel.org/r/20200518120939.1399-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Need to clear some bits in a vendor-defined register after reboot from
Windows 10.
Fixes: e51df6ce66 ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support")
Reported-by: Grzegorz Kowal <custos.mentis@gmail.com>
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Grzegorz Kowal <custos.mentis@gmail.com>
Link: https://lore.kernel.org/r/20200504063957.6638-1-benchuanggli@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The kernel prints a message similar to
"[ 28.881959] do_IRQ: 5.36 No irq handler for vector"
when GL975x resumes from suspend. Implement a resume callback to fix this.
Fixes: 31e43f3189 ("mmc: sdhci-pci-gli: Enable MSI interrupt for GL975x")
Co-developed-by: Renius Chen <renius.chen@genesyslogic.com.tw>
Signed-off-by: Renius Chen <renius.chen@genesyslogic.com.tw>
Tested-by: Dave Flogeras <dflogeras2@gmail.com>
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Tested-by: Vineeth Pillai <vineethrp@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200427103048.20785-1-benchuanggli@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
[Samuel Zou: Make sdhci_pci_gli_resume() static]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Making COMMON_CLK a visible option causes the sparc allyesconfig to fail
to build like so:
sparc64-linux-ld: drivers/mmc/host/meson-mx-sdio.o: in function `meson_mx_mmc_remove':
meson-mx-sdio.c:(.text+0x70): undefined reference to `of_platform_device_destroy'
sparc64-linux-ld: drivers/mmc/host/meson-mx-sdio.o: in function `meson_mx_mmc_probe':
meson-mx-sdio.c:(.text+0x9e4): undefined reference to `of_platform_device_create'
sparc64-linux-ld: meson-mx-sdio.c:(.text+0xdd4): undefined reference to `of_platform_device_destroy'
This is because the implementation of of_platform_device_destroy() is
inside an #ifdef CONFIG_OF_ADDRESS section of drivers/of/platform.c.
This driver already depends on OF being enabled, so let's tighten that
constrain a little more so that it depends on OF_ADDRESS instead. This
way we won't try to build this driver on platforms that don't have this
function.
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200409064416.83340-7-sboyd@kernel.org
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
BIOS writers have begun the practice of setting 40 ohm eMMC driver strength
even though the eMMC may not support it, on the assumption that the kernel
will validate the value against the eMMC (Extended CSD DRIVER_STRENGTH
[offset 197]) and revert to the default 50 ohm value if 40 ohm is invalid.
This is done to avoid changing the value for different boards.
Putting aside the merits of this approach, it is clear the eMMC's mask
of supported driver strengths is more reliable than the value provided
by BIOS. Add validation accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 51ced59cc0 ("mmc: sdhci-pci: Use ACPI DSM to get driver strength for some Intel devices")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200422111629.4899-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some reason the Host Control2 register of the Xenon SDHCI controller
sometimes reports the bit representing 1.8V signaling as 0 when read
after it was written as 1. Subsequent read reports 1.
This causes the sdhci_start_signal_voltage_switch function to report
1.8V regulator output did not become stable
When CONFIG_PM is enabled, the host is suspended and resumend many
times, and in each resume the switch to 1.8V is called, and so the
kernel log reports this message annoyingly often.
Do an empty read of the Host Control2 register in Xenon's
.voltage_switch method to circumvent this.
This patch fixes this particular problem on Turris MOX.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: 8d876bf472 ("mmc: sdhci-xenon: wait 5ms after set 1.8V...")
Cc: stable@vger.kernel.org # v4.16+
Link: https://lore.kernel.org/r/20200420080444.25242-1-marek.behun@nic.cz
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MSM sd host controller is capable of HW busy detection of device busy
signaling over DAT0 line. And it requires the R1B response for commands
that have this response associated with them.
So set the below two host capabilities for qcom SDHC.
- MMC_CAP_WAIT_WHILE_BUSY
- MMC_CAP_NEED_RSP_BUSY
Recent development of the mmc core in regards to this, revealed this as
being a potential bug, hence the stable tag.
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
