Implement the get_selection pad operation for the OV5640 sensor driver.
The supported targets report the sensor's native size, the active pixel
array size and the analog crop rectangle from which the image is
produced.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement the init_cfg pad operation to initialize the subdev state
format to the default one.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that the frame duration can be controlled by tuning the VBLANK
duration in CSI-2 mode, fix all modes definitions to comply with the
reported FPS.
All modes run at 30 FPS except for full-resolution mode 2592x1944
which runs at 15FPS.
Tested on a 2 data lanes setup in UYVY and RGB565 modes in CSI-2 mode.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The current implementation of ov5640_find_mode() fails if the
frame rate programmed with s_frame_interval doesn't match the
maximum frame rate for the current mode.
This causes issues when moving from one mode with higher FPS to another
one which only supports a lower FPS range with tools like media-ctl.
It also forces users that do not use s_frame_interval(), but rather
configure blankings explicitly, to adjust the programmed FPS range to
avoid failures.
For this reason, remove the FPS check from ov5640_find_mode() and only
perform it at s_frame_interval() time.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Adjust the vertical blanking when s_frame_interval is used.
s_frame_interval allows to set a fixed frame rate, which gets stored as
the sensor's current one. When a new mode is applied, the current frame
rate is reset to the mode's default one. In order to correctly report
the currently configured vertical blanking for s_frame_interval users,
verify that the desired frame rate has not been changed. If that's the
case, compute the correct blanking value and reflect it through the
corresponding v4l2 control.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the VBLANK control which allows to select the duration of the
frame vertical blankings and allows to control the framerate.
The VBLANK control also modifies the exposure time range, which cannot
exceed the maximum frame length.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the HBLANK control as read-only.
The hblank value is fixed in the mode definition and is updated
everytime a new format is applied.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5640_mode_init_data is a fictional sensor more which is used to
program the initial sensor settings.
It is only used to initialize the sensor and can be replaced
it with a throw-away mode which just wraps the register table.
Also rename the register table to drop the format from the name to make
it clear an actual sensor mode has to be applied after the initial
programming.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The register tables for all resolutions smaller than 720p are now
identical.
Remove the duplicated ones and create a single ov5640_setting_low_res[]
register table.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Provide a function to shortcut access to the correct timings definition
to avoid repeating the same pattern when accessing the sensor timings.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Separate the timings for the DVP mode from the timings for the CSI-2
mode in the ov5640 modes definition.
The CSI-2 timings will deviate from the DVP ones as the clock tree is
calculated differently.
In CSI-2 mode change the analog crop rectangles as the OV5640 pixel
array is composed as:
- vertically: 16 dummy columns, 2592 valid ones and 16 dummy columns for
a total of 2624 columns
- horizontally: 8 optical black lines, 6 dummy ones, 1944 valid and 6
dummies for a total of 1964 lines
Adjust the analog crop rectangle in CSI-2 mode to:
- Skip the first 16 dummy columns
- Skip the first 14 black/dummy lines
- Pass the whole valid pixel array size to the ISP for all modes except
1024x768, 720p and 1080p which are obtained by cropping the valid pixel
array.
Tested in RGB565, UYVY and RGB888 modes in CSI-2 mode.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Adjust the left crop of 720x480 to enable capture in RGB888 format,
which is otherwise broken.
The 56 pixels alignment has been copied from the 720x576 mode.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The current definition of a sensor mode defines timings as follows:
- hact, vact: Visible width and height
- htot, vtot: Total sizes including blankings
This makes difficult to clearly separate the visible sizes from the
blankings and to make the vertical blanking programmable.
Rework the sensor modes sizes definition to:
- Report the analog crop sizes
- Report the visible crop size
- Report the total pixels per line as HBLANK is fixed
- Report the VBLANK value to make it programmable
Also modify the ov5640_set_timings() function to program all the
windowing registers are remove them from the per-mode register-value
tables.
Do not change the timing values from the ones reported in the register
tables to maintain bisectability.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Re-work the ov5640_set_mipi_pclk() function to calculate the
PLL configuration using the pixel_rate and link_freq values set at
s_fmt time.
Rework the DVP clock mode settings to calculate the pixel clock
internally and remove the assumption on the 16bpp format.
Tested in MIPI CSI-2 mode with 1 and 2 data lanes with:
- all the sensor supported resolutions in UYVY, RGB565 and MJPEG formats.
- resolutions >= 1280x720 in RAW Bayer format.
- resolutions < 1280x720 in RGB888 format.
[Rework pclk_period and link_freq computation]
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
After having set a new format re-calculate the pixel_rate and link_freq
control values and update them when in MIPI mode.
Take into account the limitation of the link frequency having to be
strictly smaller than 1GHz when computing the desired link_freq, and
adjust the resulting pixel_rate acounting for the clock tree
configuration.
[Adjust link_freq calculation]
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the V4L2_CID_LINK_FREQ control to the ov5640 driver.
Make the control read-only for the moment.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Associate the bit depth to each format supported by the sensor.
The bpp will be used to calculate the line length.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Checking if the sensor is used in DVP or MIPI CSI-2 mode is a repeated
pattern which is about to be repeated more often.
Provide an inline function to shortcut that.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The array of supported modes is close to unreadable.
Re-arrange it giving it some room to breath.
Cosmetic change only.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add to each mode supported by the sensor the ideal pixel rate, as
defined by Table 2.1 in the chip manual.
The ideal pixel rate will be used to compute the MIPI CSI-2 clock tree.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon-kit
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support of 1X16 serial pixel formats in order to support
CSI-2 camera sensor exposing 1x16 pixel formats only.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Expose RGB & YUV 1X16 serial pixel format variants to comply
with CSI-2 camera sensor pixel formats.
Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Those two formats were missing in the list of supported MBUS
formats.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The s_stream callback had several issues:
- If pm_runtime_get_sync() fails, the usage_count is not put.
- The sensor wasn't suspended if s_stream(subdev, 1) failed.
Fix this.
Fixes: ("media: i2c: Add pm_runtime support to ov7251")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The A83T supports MIPI CSI-2 with a composite controller, covering
both the protocol logic and the D-PHY implementation. This controller
seems to be found on the A83T only and probably was abandoned since.
This implementation splits the protocol and D-PHY registers and
uses the PHY framework internally. The D-PHY is not registered as a
standalone PHY driver since it cannot be used with any other
controller.
There are a few notable points about the controller:
- The initialisation sequence involes writing specific magic init
values that do not seem to make any particular sense given the
concerned register fields;
- Interrupts appear to be hitting regardless of the interrupt mask
registers, which can cause a serious flood when transmission errors
occur.
Only 8-bit and 10-bit Bayer formats are currently supported.
While up to 4 internal channels to the CSI controller exist, only one
is currently supported by this implementation.
This work is based on the first version of the driver submitted by
Kévin L'hôpital, which was adapted to mainline from the Allwinner BSP.
This version integrates MIPI CSI-2 support as a standalone V4L2 subdev
instead of merging it in the sun6i-csi driver.
It was tested on a Banana Pi M3 board with an OV8865 sensor in a 4-lane
configuration.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The A31 MIPI CSI-2 controller is a dedicated MIPI CSI-2 bridge
found on Allwinner SoCs such as the A31 and V3/V3s.
It is a standalone block, connected to the CSI controller on one side
and to the MIPI D-PHY block on the other. It has a dedicated address
space, interrupt line and clock.
It is represented as a V4L2 subdev to the CSI controller and takes a
MIPI CSI-2 sensor as its own subdev, all using the fwnode graph and
media controller API.
Only 8-bit and 10-bit Bayer formats are currently supported.
While up to 4 internal channels to the CSI controller exist, only one
is currently supported by this implementation.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In reset vpu core, driver will wait for a response event,
but if there are still some events unhandled,
they will be handled first, driver may acquire core lock for that.
So if we do reset in core lock, it may led to reset timeout.
Fixes: 9f599f351e ("media: amphion: add vpu core driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The chroma order of P010 is `CbCr`,
match with the descriptions in `include/uapi/linux/videodev2.h` and the
documentation.
Fixes: 5374d8fb75 ("media: Add P010 video format")
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The mdp_ipi_comm structure defines a command that is either
PROCESS (start processing) or DEINIT (destroy instance); we
are using this one to send PROCESS or DEINIT commands from Linux
to an MDP instance through a VPU write but, while the first wants
us to stay 4-bytes aligned, the VPU instead requires an 8-bytes
data alignment.
Keeping in mind that these commands are executed immediately
after sending them (hence not chained with others before the
VPU/MDP "actually" start executing), it is fine to simply add
a padding of 4 bytes to this structure: this keeps the same
performance as before, as we're still stack-allocating it,
while avoiding hackery inside of mtk-vpu to ensure alignment
bringing a definitely bigger performance impact.
Fixes: c8eb2d7e82 ("[media] media: Add Mediatek MDP Driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Houlong Wei <houlong.wei@mediatek.com>
Reviewed-by: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
there is an unexpected word 'a' in the comments that need to be dropped
file - drivers/media/usb/pvrusb2/pvrusb2-hdw.c
line - 5044
But now it's a a chicken and egg problem...) */
changed to:
But now it's a chicken and egg problem...) */
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
there is an unexpected word 'a' in the comments that need to be dropped
file - drivers/media/platform/ti/cal/cal-camerarx.c
line - 308
* DRA80xM TRMs have a a slightly simplified sequence.
changed to:
* DRA80xM TRMs have a slightly simplified sequence.
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
there is an unexpected word 'is' in the comments that need to be dropped
file - drivers/media/usb/gspca/spca501.c
line - 491
* This is is for the 3com HomeConnect Lite which is spca501a based.
changed to:
* This is for the 3com HomeConnect Lite which is spca501a based.
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Remove the repeated word 'and' from comments
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There are a few cases where code is harder than needed to read.
Improve those by:
- dropping unnecessary castings (see note below)
- use PTR_ALING() to be more explicit on what's going on there
- use proper definitions instead of hard coded values
Note, dropping castings will allow to perform an additional check
that type is not changed from void * to something else, e.g. u64,
which may very well break the bitmap APIs.
Link: https://lore.kernel.org/linux-media/20220209182521.55632-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Here we introduce a new fault injection for SSR trigger.
To trigger the SSR:
echo 100 > /sys/kernel/debug/venus/fail_ssr/probability
echo 1 > /sys/kernel/debug/venus/fail_ssr/times
Co-developed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix build error when VIDEO_ISL7998X=y and V4L2_FWNODE=m
by selecting V4L2_FWNODE.
microblaze-linux-ld: drivers/media/i2c/isl7998x.o: in function `isl7998x_probe':
(.text+0x8f4): undefined reference to `v4l2_fwnode_endpoint_parse'
Cc: stable@vger.kernel.org # 5.18 and above
Fixes: 51ef2be546 ("media: i2c: isl7998x: Add driver for Intersil ISL7998x")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ASoC core has now been changed to default to the non-legacy DAI
naming, as such drivers using the new scheme no longer need to specify
the non_legacy_dai_naming flag.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623125250.2355471-36-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The media driver supports constant bitrate mode only.
The supported rate control mode is reported through querymenu() and
s_ctrl() fails if non constant bitrate mode (e.g. VBR) is requested.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
file: drivers/media/pci/saa7164/saa7164-api.c
line: 804
/* Assumption: Hauppauge eeprom is at 0xa0 on on bus 0 */
changed to
/* Assumption: Hauppauge eeprom is at 0xa0 on bus 0 */
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
According to subdev_bitmap bit value to open hardware power, need to
set subdev_bitmap value for non subdev architecture.
Fixes: c05bada35f ("media: mtk-vcodec: Add to support multi hardware decode")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
video_device_alloc() allocates memory for vdev,
when video_register_device() fails, it doesn't release the memory and
leads to memory leak, call video_device_release() to fix this.
Fixes: 704a84ccdb ("[media] media: Support Intersil/Techwell TW686x-based video capture cards")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In function mxc_jpeg_probe(), when devm_clk_get() fail, the return value
will be unexpected, and it should be the devm_clk_get's error code.
Fixes: 4c2e5156d9 ("media: imx-jpeg: Add pm-runtime support for imx-jpeg")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jian Zhang <zhangjian210@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The stateless decoder API does not specify the usage of SOURCE_CHANGE
and EOF events. These events are used by stateful decoders to signal
changes in the bitstream. They do not make sense for stateless decoders.
Do not handle subscription for these two types of events for stateless
decoder instances. This fixes the last v4l2-compliance error:
Control ioctls:
fail: v4l2-test-controls.cpp(946): have_source_change || have_eos
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Fixes: 8cdc3794b2 ("media: mtk-vcodec: vdec: support stateless API")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The commit in Fixes: is incomplete. It has moved some code in the probe but
not all error handling paths have been updated.
Now, if request_irq() fails, we must release some resources.
Fixes: c8946454ed96 ("media: tw686x: Register the irq at the end of probe")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fill in 10, 12, 14 bit Bayer formats into the DCMI driver.
Those are useful e.g. when MT9P006 sensor is connected.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alain Volmat <alain.volmat@foss.st.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Amelie DELAUNAY <amelie.delaunay@foss.st.com>
Cc: Hugues FRUCHET <hugues.fruchet@foss.st.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Philippe CORNU <philippe.cornu@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Need to get dec_capability from scp first, then initialize decoder
supported format and other parameters according to dec_capability value.
Fixes: fd00d90330 ("media: mtk-vcodec: vdec: move stateful ops into their own file")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When attempting to change the white balance (WB) ctrls before starting
streaming, e.g.:
# v4l2-ctl -L
User Controls
..
blue_component_gain 0x009819c1 (int) : min=0 max=8191 step=1 default=512 value=512 flags=slider
..
# v4l2-ctl --set-ctrl=blue_component_gain=500
# v4l2-ctl -L
..
blue_component_gain 0x009819c1 (int) : min=0 max=8191 step=1 default=512 value=500 flags=slider
..
These will not be written to the internal data struct and will not be
written to the WB hardware module.
Thus, after starting streaming, they will be reset to default:
# v4l2-ctl -L
..
blue_component_gain 0x009819c1 (int) : min=0 max=8191 step=1 default=512 value=512 flags=slider
..
It does not make much sense to not be able to configure the WB controls
at all times. Even if the sensor would not be RAW Bayer (and in this case the
WB module is unavailable), the user could configure the ISC itself, as the
ISC should not care about the sensor format.
Thus, when WB module is available (if the sensor changes format e.g.) it will
be already configured as be user's desires.
In consequence, remove the check in isc_s_awb_ctrl that will return if ISC
does not know the sensor format.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This driver does not use the virt_to_bus() function, though it
depends on x86 specific fixups in the swiotlb code, which was
last rewritten in commit e380a0394c ("x86/PCI: sta2x11: use
default DMA address translation").
It is possible that the driver still fails to build on some
architectures that are missing CONFIG_VIRT_TO_BUS, but it is
always set on x86 machines with the STA2X11 platform enabled.
More likely though is that it was never meant to depend on
CONFIG_VIRT_TO_BUS, and the Kconfig dependency was kept from
an out-of-tree version when the driver was originally merged.
Fixes: efeb98b4e2 ("[media] STA2X11 VIP: new V4L2 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Modify vb2ops_vdec_buf_prepare to return EINVAL if the size of the plane
is less than the size of the image. Currently we just log an error and
return 0 anyway, which may cause a buffer overrun bug.
Signed-off-by: Justin Green <greenjustin@chromium.org>
Suggested-by: Andres Calderon Jaramillo <andrescj@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If the last buffer was dequeued from the capture queue,
signal userspace. DQBUF(CAPTURE) will return -EPIPE.
But if output queue is empty and capture queue is empty,
v4l2_m2m_poll_for_data will return EPOLLERR,
This is very easy to happen in drain.
When last_buffer_dequeued is set, we shouldn't return EPOLLERR,
but return EPOLLIN | EPOLLRDNORM.
Fixes: 1698a7f151 ("media: v4l2-mem2mem: simplify poll logic")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Eliminate the following coccicheck warning:
./drivers/media/platform/mediatek/vcodec/mtk_vcodec_dec.c:71:2-3: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Error return values are supposed to be negative in hdpvr_read. Most
error returns are currently handled via an unsigned integer "ret". When
setting a negative error value to "ret", the value actually becomes a
large positive value, because "ret" is unsigned. Later on, the "ret"
value is returned. But as ssize_t is a 64-bit signed number, the error
return value stays a large positive integer instead of a negative
integer. This can cause an error value to be interpreted as the read
size, which can cause a buffer overread for applications relying on the
returned size.
Fixes: 9aba42efe8 ("V4L/DVB (11096): V4L2 Driver for the Hauppauge HD PVR usb capture device")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
An SPDX-License-Identifier is already in place. There is no need to
duplicate part of the corresponding license.
While at it, a few comments at the end of some .h files have been updated
to reflect the correct include guard name (missing '_' and co.)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
An SPDX-License-Identifier is already in place. There is no need to
duplicate part of the corresponding license.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
An SPDX-License-Identifier is already in place. There is no need to
duplicate part of the corresponding license.
This is a left-over from commit adeb697056 ("media: rcar_drif: convert to
SPDX identifiers")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The Google Kinox device uses the same approach as the Google Brask
which enables the HDMI CEC via the cros-ec-cec driver.
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Firmware may send the error event with some error message,
and it help locate the firmware error,
so output the error message if it exists
Fixes: 61cbf1c1fa ("media: amphion: implement vpu core communication based on mailbox")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The interrupt STMBUF_HALF may be triggered after frame done.
It may led to system hang if driver try to access the register after
power off.
Disable the slot interrupt when frame done.
Fixes: 2db16c6ed7 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Tested-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Change the value of v4l2 capability parameters: driver and card.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix v4l2 capability bus_info value with correct chip name according to
compatible.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Change the value of v4l2 capability parameters: driver and card.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix v4l2 capability bus_info value with correct chip name according to
compatible.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make the code more readable by using the same alignment for all macros
in rkisp1-common.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When handling querycap, the capture node would access the main rkisp1
device unnecessarily. Get the information from the most direct source.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Update the maximum register name length to match all the registers being
printed. This helps getting a consistent alignment of register dumps
when concatenating multiple debugfs files.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Extend the rkisp1_debug_register structure and the
rkisp1_debug_dump_regs() function to support shadow registers, and
replace the manual registers dump implementation in
rkisp1_debug_dump_rsz_regs_show() with a call to
rkisp1_debug_dump_regs().
Support for printing register values in decimal is dropped, as it was
actually confusing to print resizer register expressed as fixed-point
values in decimal.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The debugfs support already includes support to dump core and ISP
registers. Move the resizer register dump there too to make the
userspace interface consistent.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It's useful to dump the value of registers for debugging purpose. Add
two debugfs files to dump key core and ISP registers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ISP_FLAGS_SHD register exposes the ISP parallel input signals (data
and synchronization) in real time. This can help debugging when the
device doesn't output any image. Sample the register 10000 times with a
1µs delay and expose the result through debugfs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When CONFIG_DEBUGFS is disabled, there's no need to compile the debugfs
support in. Make it conditional.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
To avoid cluttering the main rkisp1-dev.c driver file, move debugfs code
to a separate source file. This prepares for extensions to the debugfs
infrastructure.
While at it, add a missing forward declaration for struct dentry in
rkisp1-common.h to avoid depending on indirect includes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The registers for the mainpath and selfpath resizers are located at the
same offset from the instance-specific base. Use this to simplify
register access, removing the need to store per-register offsets in the
rkisp1_rsz_config structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
While writel() takes the value and address arguments in that order, most
write functions (including in the regmap API) use the opposite
convention. Having the value first is considered confusing, and often
leads to more difficult to read code compared to the opposite convention
where the write call and the register name often fit on a single line:
rkisp1_write(rkisp1, RKISP1_CIF_THE_REG_NAME,
complicate_calculation + for / the_register
value + goes | here);
Swap the arguments of the rkisp1_write() function, and use the following
semantic patch to update the callers:
@@
expression rkisp1, value, address;
@@
- rkisp1_write(rkisp1, value, address)
+ rkisp1_write(rkisp1, address, value)
This commit also includes a few additional line break cleanups in the
rkisp1_write() calls, but no other manual change.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The documentation names the CCL, ICCL and IRCL registers with a VI_
prefix, like the VI_ID and VI_DPCL registers. Fix the macro names
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The BIT() macro is meant to represent a single bit. It is incorrectly
used for register field values that store the value 1 in a multi-bit
field. Use the usual (1 << n) construct for those.
While at it, move RKISP1_CIF_MI_DMA_CTRL_READ_FMT_PACKED where it
belongs with the other READ_FMT values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that all the unregistration functions are safe to call on
non-registered entities, the error path in rkisp1_entities_register()
can be simplified. Factor out the unregistration to a separate function
to share code with rkisp1_remove().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Simplify error handling at registration time as media_entity_cleanup()
can be called on an uninitialized entity, and make
rkisp1_stats_unregister() safe to be called on an unregistered stats
node to prepare for simplification of error handling at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The rkisp1_params_register() and rkisp1_params_unregister() functions
don't destroy the mutex (in the error path for the former). Fix this,
simplify error handling at registration time as media_entity_cleanup()
can be called on an uninitialized entity, and make
rkisp1_params_unregister() safe to be called on an unregistered params
node to prepare for simplification of error handling at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The rkisp1_rsz_register() and rkisp1_rsz_unregister() functions don't
destroy the mutex (in the error path for the former). Fix this, simplify
error handling at registration time as media_entity_cleanup() can be
called on an uninitialized entity, and make rkisp1_rsz_unregister() and
rkisp1_resizer_devs_unregister() safe to be called on an unregistered
resizer subdev to prepare for simplification of error handling at probe
time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The rkisp1_isp_register() and rkisp1_isp_unregister() functions don't
destroy the mutex (in the error path for the former). Fix this, simplify
error handling at registration time as media_entity_cleanup() can be
called on an uninitialized entity, and make rkisp1_isp_unregister() and
safe to be called on an unregistered isp subdev to prepare for
simplification of error handling at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The rkisp1_register_capture() and rkisp1_unregister_capture() functions
don't destroy the mutex (in the error path for the former). Fix this and
make rkisp1_unregister_capture() and rkisp1_capture_devs_unregister()
safe to be called on an unregistered capture node to prepare for
simplification of error handling at probe time.
While at it, drop the double initialization of cap->rkisp1 in
rkisp1_capture_devs_register() as the field is already initialized in
rkisp1_capture_init().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The media_entity embedded in the video_device needs to be initialized
before registering the video_device. Do so.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The error handling code in pvr2_hdw_create forgets to unregister the
v4l2 device. When pvr2_hdw_create returns back to pvr2_context_create,
it calls pvr2_context_destroy to destroy context, but mp->hdw is NULL,
which leads to that pvr2_hdw_destroy directly returns.
Fix this by adding v4l2_device_unregister to decrease the refcount of
usb interface.
Reported-by: syzbot+77b432d57c4791183ed4@syzkaller.appspotmail.com
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When converting to full Virtual Channel routing an error crept into the
routing table for Ebisu (r8a77990). The routing information is used at
probe time preventing rcar-vin from probing correctly on this SoC, solve
by correcting the routing table.
Fixes: 3e52419ec0 ("media: rcar-{csi2,vin}: Move to full Virtual Channel routing per CSI-2 IP")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Set allow_cache_hints to 1 for the vb2_queue source and destination queues
in the mediatek vcodec V4L2 driver. This allows us to allocate buffers
with the V4L2_MEMORY_FLAG_NON_COHERENT set. On Mediatek SoCs, this enables
caching for this memory, which vastly improves performance when being read
from CPU. Read performance for these buffers is in turn important for
detiling MM21 video frames in userspace software, such as libyuv or
gstreamer.
This change should be safe from race conditions since videobuf2 already
invalidates or flushes the appropriate cache lines in its prepare() and
finish() methods.
Tested on a MT8183 SoC. Resulted in both correct detiling and a 10X
speedup.
Signed-off-by: Justin Green <greenjustin@chromium.org>
Suggested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
vfree(NULL) is safe. NULL check before vfree() is not needed.
Delete them to simplify the code.
Generated by coccinelle script:
scripts/coccinelle/free/ifnullfree.cocci
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: ming_qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
v4l2 m2m has supplied some helper function to handle drain,
so the driver can use the helper function directly.
Fixes: d8ebe298d0 ("media: imx-jpeg: Set V4L2_BUF_FLAG_LAST at eos")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The hardware can support any image size WxH,
with arbitrary W (image width) and H (image height) dimensions.
Align upwards buffer size for both encoder and decoder.
and leave the picture resolution unchanged.
For decoder, the risk of memory out of bounds can be avoided.
For both encoder and decoder, the driver will lift the limitation of
resolution alignment.
For example, the decoder can support jpeg whose resolution is 227x149
the encoder can support nv12 1080P, won't change it to 1920x1072.
Fixes: 2db16c6ed7 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is a hardware bug that it will load
the first 128 bytes of configuration data twice,
it will led to some configure error.
so shift the configuration data 128 bytes,
and make the first 128 bytes all zero,
then hardware will load the 128 zero twice,
and ignore them as garbage.
then the configuration data can be loaded correctly
Fixes: 2db16c6ed7 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
the register CAST_NOMFRSIZE_LO should be equal to CAST_STATUS16
the register CAST_NOMFRSIZE_HI should be equal to CAST_STATUS17
the register CAST_OFBSIZE_LO should be equal to CAST_STATUS18
the register CAST_OFBSIZE_HI should be equal to CAST_STATUS19
Fixes: 2db16c6ed7 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In error case of s5p_mfc_power_on() we should call
clk_disable_unprepare() for the
clocks(from pm->clocks[0] to pm->clocks[i-1]).
Signed-off-by: Chengguang Xu <cgxu519@mykernel.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is a regular need in the kernel to provide a way to declare
having a dynamically sized set of trailing elements in a structure.
Kernel code should always use “flexible array members”[1] for these
cases. The older style of one-element or zero-length arrays should no
longer be used[2][3].
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays
[3] https://github.com/KSPP/linux/issues/78
Fixes: 9f599f351e ("media: amphion: add vpu core driver")
Cc: Ming Qian <ming.qian@nxp.com>
Cc: Shijie Qin <shijie.qin@nxp.com>
Cc: Zhou Peng <eagle.zhou@nxp.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: ming_qian <ming.qian@nxp.com>
Reviewed-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The cropping configuration of the Parallel Front Engine (PFE) can be done
just once when the streaming starts. The ISC configuration is in place and
will not be changed while streaming.
It is not effective to keep rewriting the crop registers configuration
everytime start_dma is called, as this can be called for each queued
buffer.
Thus we can configure the cropping at start_streaming time.
This change moves the code to a dedicated function.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Common exported functions msm_vfe_get_vfe_id() and
msm_vfe_get_vfe_line_id() do not have any users outside of camss-ispif.c,
move them to the latter object and staticize.
The change is supposed to be a non-functional one.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
return error if format is unsupported by vpu,
otherwise the vpu will be stalled at decoding
Fixes: 3cd084519c ("media: amphion: add vpu v4l2 m2m support")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Spelling mistakes (triple letters) in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
We got the following warning when booting the kernel:
[ 3.243674] INFO: trying to register non-static key.
[ 3.243922] The code is fine but needs lockdep annotation, or maybe
[ 3.244230] you didn't initialize this object before use?
[ 3.245642] Call Trace:
[ 3.247836] lock_acquire+0xff/0x2d0
[ 3.248727] tw686x_audio_irq+0x1a5/0xcc0 [tw686x]
[ 3.249211] tw686x_irq+0x1f9/0x480 [tw686x]
The lock 'vc->qlock' will be initialized in tw686x_video_init(), but the
driver registers the irq before calling the tw686x_video_init(), and we
got the warning.
Fix this by registering the irq at the end of probe
Fixes: 704a84ccdb ("[media] media: Support Intersil/Techwell TW686x-based video capture cards")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When removing the module, we will get the follow flaw:
[ 69.323999] remove_proc_entry: removing non-empty directory 'irq/21', leaking at least 'tw5864'
[ 69.324449] WARNING: CPU: 0 PID: 395 at fs/proc/generic.c:717 remove_proc_entry+0x389/0x3f0
[ 69.326909] RIP: 0010:remove_proc_entry+0x389/0x3f0
[ 69.331089] Call Trace:
[ 69.331215] <TASK>
[ 69.331327] unregister_irq_proc+0x14c/0x170
[ 69.332579] tw5864_finidev+0x12a/0x190 [tw5864]
[ 69.332811] pci_device_remove+0x92/0x240
Fix this by using managed functions, this makes the error handling more
simpler.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The Google Moli device uses the same approach as the Google Brask
which enables the HDMI CEC via the cros-ec-cec driver.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
A pointer into virtual memory is represented by a (void *)
not an u32, so the compiler warns:
drivers/media/platform/ti/omap/omap_voutlib.c:317:54: warning:
passing argument 1 of 'virt_to_pfn' makes pointer from integer
without a cast [-Wint-conversion]
Fix this with an explicit cast.
Cc: Vaibhav Hiremath <hvaibhav.linux@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
vdec check the pixel format is supported by vpu,
or is it disabled.
And don't report it if the result is false
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The change simplifies driver's probe and remove functions, no functional
change is intended.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If we want to avoid memory corruption
on incoherent architectures, buffers for DMA
must not reside
- on the stack
- embedded within other structures
Allocate them separately.
v2: fix uninitialized return value
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
set jpeg encode DMA bit mask to support 34bits
iova space(16GB) that the mt8186 iommu HW support.
Whole the iova range separate to 0~4G/4G~8G/8G~12G/12G~16G,
regarding which iova range jpgenc actually locate, it
depends on the dma-ranges property of vdec dtsi node.
Signed-off-by: kyrie wu <kyrie.wu@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use ida_alloc() and ida_free() instead of the deprecated
ida_simple_get() and ida_simple_remove().
Signed-off-by: keliu <liuke94@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
While the completion handler is running,
usb_unlink_urb() on yourself is a NOP. Remove it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
During resume we must assume tat devices are
not ready for block IO. Use GFP_NOIO.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It cannot fail. Make it void.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
During resume() GFP_NOIO is enough.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
During resume() GFP_NOIO will do.
No need for GFP_ATOMIC
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
No buffer can be embedded inside a descriptor, not even a simple be64.
Use a separate kmalloc()
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Unlinking yourself while the completion handler
is running is a NOP. Drop it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Calling that on yourself while the completion handler
is running is a NOP. Remove it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver uses a timer, that may submit the URB and
the URB may start the timer. No simple order of killing
can break te cycle. Poison the URB before killing
the timer.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The timer uses the URB. Free it only after the timer
has been stopped.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The coherency rules mean that you cannot embed
a buffer inside a descriptor. kmalloc() separately.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In order to reduce decoder latency, enable H264 inner racing mode.
Send lat trans buffer information to core when trigger lat to work,
need not to wait until lat decode done.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Vp8 need to use MM21, but vp9 and h264 need to use HyFbc mode
for mt8195. Vp8/vp9/h264 use the same MM21 format for mt8192.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add lat soc compatible and to support lat soc power/clk helper.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
P010 is a YUV format with 10-bits per component with interleaved UV.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement V4L2_CID_JPEG_COMPRESSION_QUALITY
to set jpeg quality
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix the following coccicheck warning:
drivers/media/platform/samsung/s5p-jpeg/jpeg-core.c:1712:24-25:
WARNING opportunity for max()
max() macro is defined in include/linux/minmax.h. It avoids multiple
evaluations of the arguments when non-constant and performs strict
type-checking.
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This bit is marked as reserved in the ADV Hardware Reference Manual.
Resetting this bit seems to cause increased video noise. Setting this
bit according to the Hardware Reference Manual reduces the video noise
immediately.
Signed-off-by: Benjamin Marty <info@benjaminmarty.ch>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This is a very old driver for very old hardware and it is one of
the very few remaining that does not use the vb2 framework (or
even the older videobuf framework), so deprecate this driver
and move it to staging with the intent to removing it altogether
by the end of 2022.
If someone wants to keep this driver, then it has to be converted
to use vb2.
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The variables f_chk_len and f_chk_addr are being initialized to zero and
then being re-assigned in the next statement. The initializations are
redundant and can be removed. Also initialize s_chk_addr and s_chk_len
at the declaration statement.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As there is no interface to power off vpu core.
So it need to boot from cold on first load.
but on the second load, driver need to restore the status
instead of booting.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Eliminate the following coccicheck warning:
./drivers/media/platform/atmel/atmel-isc-base.c:1469:2-3: Unneeded
semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
clk_prepare_enable() already checks NULL by using !clk.
clk_disable_unprepare() already checks NULL by using IS_ERR_OR_NULL.
Remove unneeded NULL checks before them.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add PAL-Nc support to usbtv, the corresponding register value "0x00fe"
comes from the Windows driver "Active Development Co., Ltd. v2.1.1.2".
Signed-off-by: Jorge Maidana <jorgem.linux@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
* Fix PAL-Nc horizontal parameters according to DScaler:
https://github.com/JohnAdders/DScaler/blob/f7d92b76678e/DScaler/TVFormats.cpp#L88-L94
* Add PAL-Nc TV audio support.
* Tested with CVBS and RF on a Pinnacle PCTV HD 800i.
Signed-off-by: Jorge Maidana <jorgem.linux@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a vivid control to insert the HDMI Video Guard Band in the
image.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This inserts 4 pixels of the RGB color 0xab55ab at the left hand side of
the image. This is only done for 3 or 4 byte RGB pixel formats. The HDMI
TMDS encoding of this pixel value equals the Video Guard Band value as
defined by HDMI (see section 5.2.2.1 in the HDMI 1.3 Specification) that
preceeds the first actual pixel of a video line. If an HDMI receiver
doesn't handle this correctly, then it might keep skipping these Video
Guard Band patterns and end up with a shorter video line. So this is a
nice pattern to test with.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If there is a hardware problem such as someone pulling the CEC line low
continuously, then the POLL message will fail with an error other than
OK, NACK, ABORTED or TIMEOUT. Log the tx_status value in that case to
help debug this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When logging the infoframes the adv7604 driver stopped reading
infoframes at the first missing infoframe type. Instead it should
try all supported infoframe types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
To simplify the driver's maintenance it makes sense to escape from
hardcoded numbers of power domain resources per platform and statical
allocation of the resources. For instance on a QCOM SM8450 platform
the number of CAMSS power domains shall be bumped up to 6, also notably
CAMSS on MSM8916 has only one power domain, however it expects to get 2,
and thus it should result in a runtime error on driver probe.
The change fixes an issue mentioned above and gives more flexibility
to support more platforms in future.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
of_graph_get_next_endpoint() returns an 'endpoint' node pointer
with refcount incremented. The refcount should be decremented
before returning from vpif_probe().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver should disable the regulator when failing to probe.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
'supplies' is a pointer, the real size of struct regulator_bulk_data
should be pass to devm_kmalloc_array().
Fixes: 0d81401797 ("media: camss: Add regulator_bulk support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The core will fill this in v4l_fill_fmtdesc(),
ensuring consistent format description names.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for the
USB core, but there are the usual "hot spots" of development activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes. It seems this driver will never
be finished given that the IP core is showing up in zillions
of new devices and each implementation decides to do something
different with it...
- uvc gadget driver updates as more devices start to use and
rely on this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnZGw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymQhwCeLVANsQjBcL4ys4skl+1In17y28gAn3rEZ7rQ
Yv4uP9zadUqg3Cx0vjgf
=3s5s
-----END PGP SIGNATURE-----
Merge tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
Core
----
- Support TCPv6 segmentation offload with super-segments larger than
64k bytes using the IPv6 Jumbogram extension header (AKA BIG TCP).
- Generalize skb freeing deferral to per-cpu lists, instead of
per-socket lists.
- Add a netdev statistic for packets dropped due to L2 address
mismatch (rx_otherhost_dropped).
- Continue work annotating skb drop reasons.
- Accept alternative netdev names (ALT_IFNAME) in more netlink
requests.
- Add VLAN support for AF_PACKET SOCK_RAW GSO.
- Allow receiving skb mark from the socket as a cmsg.
- Enable memcg accounting for veth queues, sysctl tables and IPv6.
BPF
---
- Add libbpf support for User Statically-Defined Tracing (USDTs).
- Speed up symbol resolution for kprobes multi-link attachments.
- Support storing typed pointers to referenced and unreferenced
objects in BPF maps.
- Add support for BPF link iterator.
- Introduce access to remote CPU map elements in BPF per-cpu map.
- Allow middle-of-the-road settings for the
kernel.unprivileged_bpf_disabled sysctl.
- Implement basic types of dynamic pointers e.g. to allow for
dynamically sized ringbuf reservations without extra memory copies.
Protocols
---------
- Retire port only listening_hash table, add a second bind table
hashed by port and address. Avoid linear list walk when binding
to very popular ports (e.g. 443).
- Add bridge FDB bulk flush filtering support allowing user space
to remove all FDB entries matching a condition.
- Introduce accept_unsolicited_na sysctl for IPv6 to implement
router-side changes for RFC9131.
- Support for MPTCP path manager in user space.
- Add MPTCP support for fallback to regular TCP for connections
that have never connected additional subflows or transmitted
out-of-sequence data (partial support for RFC8684 fallback).
- Avoid races in MPTCP-level window tracking, stabilize and improve
throughput.
- Support lockless operation of GRE tunnels with seq numbers enabled.
- WiFi support for host based BSS color collision detection.
- Add support for SO_TXTIME/SCM_TXTIME on CAN sockets.
- Support transmission w/o flow control in CAN ISOTP (ISO 15765-2).
- Support zero-copy Tx with TLS 1.2 crypto offload (sendfile).
- Allow matching on the number of VLAN tags via tc-flower.
- Add tracepoint for tcp_set_ca_state().
Driver API
----------
- Improve error reporting from classifier and action offload.
- Add support for listing line cards in switches (devlink).
- Add helpers for reporting page pool statistics with ethtool -S.
- Add support for reading clock cycles when using PTP virtual clocks,
instead of having the driver convert to time before reporting.
This makes it possible to report time from different vclocks.
- Support configuring low-latency Tx descriptor push via ethtool.
- Separate Clause 22 and Clause 45 MDIO accesses more explicitly.
New hardware / drivers
----------------------
- Ethernet:
- Marvell's Octeon NIC PCI Endpoint support (octeon_ep)
- Sunplus SP7021 SoC (sp7021_emac)
- Add support for Renesas RZ/V2M (in ravb)
- Add support for MediaTek mt7986 switches (in mtk_eth_soc)
- Ethernet PHYs:
- ADIN1100 industrial PHYs (w/ 10BASE-T1L and SQI reporting)
- TI DP83TD510 PHY
- Microchip LAN8742/LAN88xx PHYs
- WiFi:
- Driver for pureLiFi X, XL, XC devices (plfxlc)
- Driver for Silicon Labs devices (wfx)
- Support for WCN6750 (in ath11k)
- Support Realtek 8852ce devices (in rtw89)
- Mobile:
- MediaTek T700 modems (Intel 5G 5000 M.2 cards)
- CAN:
- ctucanfd: add support for CTU CAN FD open-source IP core
from Czech Technical University in Prague
Drivers
-------
- Delete a number of old drivers still using virt_to_bus().
- Ethernet NICs:
- intel: support TSO on tunnels MPLS
- broadcom: support multi-buffer XDP
- nfp: support VF rate limiting
- sfc: use hardware tx timestamps for more than PTP
- mlx5: multi-port eswitch support
- hyper-v: add support for XDP_REDIRECT
- atlantic: XDP support (including multi-buffer)
- macb: improve real-time perf by deferring Tx processing to NAPI
- High-speed Ethernet switches:
- mlxsw: implement basic line card information querying
- prestera: add support for traffic policing on ingress and egress
- Embedded Ethernet switches:
- lan966x: add support for packet DMA (FDMA)
- lan966x: add support for PTP programmable pins
- ti: cpsw_new: enable bc/mc storm prevention
- Qualcomm 802.11ax WiFi (ath11k):
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- enable keep-alive during WoWLAN suspend
- implement remain-on-channel support
- MediaTek WiFi (mt76):
- support Wireless Ethernet Dispatch offloading packet movement
between the Ethernet switch and WiFi interfaces
- non-standard VHT MCS10-11 support
- mt7921 AP mode support
- mt7921 IPv6 NS offload support
- Ethernet PHYs:
- micrel: ksz9031/ksz9131: cabletest support
- lan87xx: SQI support for T1 PHYs
- lan937x: add interrupt support for link detection
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Wjii
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core
----
- Support TCPv6 segmentation offload with super-segments larger than
64k bytes using the IPv6 Jumbogram extension header (AKA BIG TCP).
- Generalize skb freeing deferral to per-cpu lists, instead of
per-socket lists.
- Add a netdev statistic for packets dropped due to L2 address
mismatch (rx_otherhost_dropped).
- Continue work annotating skb drop reasons.
- Accept alternative netdev names (ALT_IFNAME) in more netlink
requests.
- Add VLAN support for AF_PACKET SOCK_RAW GSO.
- Allow receiving skb mark from the socket as a cmsg.
- Enable memcg accounting for veth queues, sysctl tables and IPv6.
BPF
---
- Add libbpf support for User Statically-Defined Tracing (USDTs).
- Speed up symbol resolution for kprobes multi-link attachments.
- Support storing typed pointers to referenced and unreferenced
objects in BPF maps.
- Add support for BPF link iterator.
- Introduce access to remote CPU map elements in BPF per-cpu map.
- Allow middle-of-the-road settings for the
kernel.unprivileged_bpf_disabled sysctl.
- Implement basic types of dynamic pointers e.g. to allow for
dynamically sized ringbuf reservations without extra memory copies.
Protocols
---------
- Retire port only listening_hash table, add a second bind table
hashed by port and address. Avoid linear list walk when binding to
very popular ports (e.g. 443).
- Add bridge FDB bulk flush filtering support allowing user space to
remove all FDB entries matching a condition.
- Introduce accept_unsolicited_na sysctl for IPv6 to implement
router-side changes for RFC9131.
- Support for MPTCP path manager in user space.
- Add MPTCP support for fallback to regular TCP for connections that
have never connected additional subflows or transmitted
out-of-sequence data (partial support for RFC8684 fallback).
- Avoid races in MPTCP-level window tracking, stabilize and improve
throughput.
- Support lockless operation of GRE tunnels with seq numbers enabled.
- WiFi support for host based BSS color collision detection.
- Add support for SO_TXTIME/SCM_TXTIME on CAN sockets.
- Support transmission w/o flow control in CAN ISOTP (ISO 15765-2).
- Support zero-copy Tx with TLS 1.2 crypto offload (sendfile).
- Allow matching on the number of VLAN tags via tc-flower.
- Add tracepoint for tcp_set_ca_state().
Driver API
----------
- Improve error reporting from classifier and action offload.
- Add support for listing line cards in switches (devlink).
- Add helpers for reporting page pool statistics with ethtool -S.
- Add support for reading clock cycles when using PTP virtual clocks,
instead of having the driver convert to time before reporting. This
makes it possible to report time from different vclocks.
- Support configuring low-latency Tx descriptor push via ethtool.
- Separate Clause 22 and Clause 45 MDIO accesses more explicitly.
New hardware / drivers
----------------------
- Ethernet:
- Marvell's Octeon NIC PCI Endpoint support (octeon_ep)
- Sunplus SP7021 SoC (sp7021_emac)
- Add support for Renesas RZ/V2M (in ravb)
- Add support for MediaTek mt7986 switches (in mtk_eth_soc)
- Ethernet PHYs:
- ADIN1100 industrial PHYs (w/ 10BASE-T1L and SQI reporting)
- TI DP83TD510 PHY
- Microchip LAN8742/LAN88xx PHYs
- WiFi:
- Driver for pureLiFi X, XL, XC devices (plfxlc)
- Driver for Silicon Labs devices (wfx)
- Support for WCN6750 (in ath11k)
- Support Realtek 8852ce devices (in rtw89)
- Mobile:
- MediaTek T700 modems (Intel 5G 5000 M.2 cards)
- CAN:
- ctucanfd: add support for CTU CAN FD open-source IP core from
Czech Technical University in Prague
Drivers
-------
- Delete a number of old drivers still using virt_to_bus().
- Ethernet NICs:
- intel: support TSO on tunnels MPLS
- broadcom: support multi-buffer XDP
- nfp: support VF rate limiting
- sfc: use hardware tx timestamps for more than PTP
- mlx5: multi-port eswitch support
- hyper-v: add support for XDP_REDIRECT
- atlantic: XDP support (including multi-buffer)
- macb: improve real-time perf by deferring Tx processing to NAPI
- High-speed Ethernet switches:
- mlxsw: implement basic line card information querying
- prestera: add support for traffic policing on ingress and egress
- Embedded Ethernet switches:
- lan966x: add support for packet DMA (FDMA)
- lan966x: add support for PTP programmable pins
- ti: cpsw_new: enable bc/mc storm prevention
- Qualcomm 802.11ax WiFi (ath11k):
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- enable keep-alive during WoWLAN suspend
- implement remain-on-channel support
- MediaTek WiFi (mt76):
- support Wireless Ethernet Dispatch offloading packet movement
between the Ethernet switch and WiFi interfaces
- non-standard VHT MCS10-11 support
- mt7921 AP mode support
- mt7921 IPv6 NS offload support
- Ethernet PHYs:
- micrel: ksz9031/ksz9131: cabletest support
- lan87xx: SQI support for T1 PHYs
- lan937x: add interrupt support for link detection"
* tag 'net-next-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1809 commits)
ptp: ocp: Add firmware header checks
ptp: ocp: fix PPS source selector debugfs reporting
ptp: ocp: add .init function for sma_op vector
ptp: ocp: vectorize the sma accessor functions
ptp: ocp: constify selectors
ptp: ocp: parameterize input/output sma selectors
ptp: ocp: revise firmware display
ptp: ocp: add Celestica timecard PCI ids
ptp: ocp: Remove #ifdefs around PCI IDs
ptp: ocp: 32-bit fixups for pci start address
Revert "net/smc: fix listen processing for SMC-Rv2"
ath6kl: Use cc-disable-warning to disable -Wdangling-pointer
selftests/bpf: Dynptr tests
bpf: Add dynptr data slices
bpf: Add bpf_dynptr_read and bpf_dynptr_write
bpf: Dynptr support for ring buffers
bpf: Add bpf_dynptr_from_mem for local dynptrs
bpf: Add verifier support for dynptrs
bpf: Suppress 'passing zero to PTR_ERR' warning
bpf: Introduce bpf_arch_text_invalidate for bpf_prog_pack
...
As per spec, the field reflist requires interleaving top and bottom
field in a specific way that does not fit inside the sort operation.
The process consist of alternating references parity, starting with
a reference of the same parity as the current picture. This
processs is done twice, once for short term references and a second
time for the long term references.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In the reference list builder, frame_num refers to FrameNumWrap
in the spec, which is the same as the pic_num for frame decoding.
The same applies for long_term_pic_num and long_term_frame_idx.
Sort all type of references by frame_num so the sort can be reused
for fields reflist were the sorting is done using frame_num instead.
In short, pic_num is never actually used for building reference
lists.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add debug print statements to print the content of P & B reference
lists, to verify that the ordering of the generated reference lists is
correct. This is especially important for the field decoding mode,
where sorting is more complex.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When the current picture is a field, store each field into the
unordered_list and preserve both top and bottom picture order
count.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This information, also called picture structure, is required in field
decoding mode to construct reference lists.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This is to accommodate support for field decoding, which splits the top
and the bottom references into the reference list.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In preparation for adding field decoding support, convert the byte arrays
for reflist into array of struct v4l2_h264_reference. That struct will
allow us to mark which field of the reference picture is being referenced.
[hverkuil: top_field_order_cnt -> pic_order_count]
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As reported by smatch/sparse:
drivers/media/i2c/ov7251.c:1381 ov7251_s_stream() warn: inconsistent returns '&ov7251->lock'.
Locked on : 1381
Unlocked on: 1377
There's a lock unbalance at this routine, as it keeps the lock on
certain errors. Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a vblank control to the ov7251 driver.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a hblank control to the ov7251 driver. This necessitates setting
a default mode, for which I am simply picking the first available.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
V4L2 controls initialisation takes up a sizeable portion of the
driver's .probe() function. To keep things neat, move it to a
dedicated function.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Extend the .get_selection() callback to support other values for
sel->target, primarily to satisfy libcamera's requirements.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The OVTI7251 sensor can be found on x86 laptops with an IPU3, and so
needs to be supported by the cio2-bridge. Add it to the table of
supported sensors.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The .s_power() callback is deprecated, and now that we have pm_runtime
functionality in the driver there's no further use for it. Delete the
function.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add pm_runtime support to the ov7251 driver.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe() is quite busy for this driver; make it cleaner by moving the
chip verification to a dedicated function.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The OV7251 sensor is used as the IR camera sensor on the Microsoft
Surface line of tablets; this provides a 19.2MHz external clock, and
the Windows driver for this sensor configures a 319.2MHz link freq to
the CSI-2 receiver. Add the ability to support those rate to the
driver by defining a new set of PLL configs.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Rather than having the pll settings hidden inside mode blobs, define
them in structs and use a dedicated function to set them. This makes
it simpler to extend the driver to support other frequencies for both
the external clock and desired link frequency.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Each of the defined modes in the ov7251 driver uses the same link
frequency and pixel rate; just drop those members of the modes and
set the controls to read only during initialisation. Add a new
table defining the supported pixel rates to substitue for the values
hardcoded in the modes.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move the endpoint checking from .probe() to a dedicated function,
and additionally check that the firmware provided link frequencies
are a match for those supported by the driver. Store the index to the
matching link frequency so it can be easily identified later.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for enumeration through ACPI to the ov7251 driver
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
We have platforms where a camera sensor transmits Y10 data to
the CIO2 device - add support for that (packed) format to the
ipu3-cio2 driver.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Some platforms with an Intel IPU3 have an IR sensor producing 10 bit
greyscale format data that is transmitted over a CSI-2 bus to a CIO2
device - this packs the data into 32 bytes per 25 pixels. Add an entry
to the uAPI header defining that format.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
of_match_ptr isn't required as CONFIG_OF is already a dependency in Kconfig
Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MWB gain register are used to set gain for each mwb channel mannually.
However, it will involve some artifacts if gain cannot be applied to
each channel synchronously. Enable global gain control to set digital
global gain instead of setting AWB gain separately to fix this issue.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
IS_ERR() and PTR_ERR() use wrong pointer, it should be
sensor->dovdd, fix it.
Fixes: e43ccb0a04 ("media: i2c: Add support for the OV5648 image sensor")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add V4L2_ASYNC as a dependency to match other drivers and prevent failures
when compile testing.
Fixes: ff3cc65cad ("media: v4l: async, fwnode: Improve module organisation")
Signed-off-by: Mike Pagano <mpagano@gentoo.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Currently, the defines in this driver are after some structs and
functions, it makes more sense to move them up to the top of the file,
so that the constants can be named together with other defines.
Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Declare static on function 'fimc_isp_video_device_unregister'.
When VIDEO_EXYNOS4_ISP_DMA_CAPTURE=n, compiler warns about
warning: no previous prototype for function [-Wmissing-prototypes]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kwanghoon Son <k.son@samsung.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
ADV7180 has a built-in mechanism to generate some video patterns,
which is very useful for debug/bring-up activities.
Add support for it.
The test_pattern parameter can be one of the following values:
0: "Single color"
1: "Color bars"
2: "Luma ramp"
3: "Boundary box"
4: "Disable"
Tested on a imx6q board with an ADV7280.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use get_frame_desc() to get the frame desc from the connected source,
and use the provided virtual channel and datatype instead of hardcoded
ones.
get_frame_desc() can contain multiple streams, but as we don't support
multiple streams yet, we will just always use the first stream.
If the source doesn't support get_frame_desc(), fall back to the
previous method of always capturing virtual channel 0 and any datatype.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As V4L2_FWNODE_BUS_TYPE_PARALLEL is not used for DPI interface, this
patch add V4L2_FWNODE_BUS_TYPE_DPI for video DPI interface.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In ov7670_probe, it always invokes ov7670_power_off() no matter
the execution is successful or failed. So we cannot invoke it
agiain in ov7670_remove().
Fix this by removing ov7670_power_off from ov7670_remove.
Fixes: 030f9f682e ("media: ov7670: control clock along with power")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is firmware out there that uses "dongwoon,dw9807" compatible string
that never made it to upstream as-is. Add it to the driver to make it load
on such systems.
The chip also has an EEPROM part which is AT24 compatible (for reading
purposes) on a separate I²C address. Adding possible support for this in
the future is not affected by this change.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Depending on the platform we may need to enable and disable three separate
regulators for the imx412.
- DOVDD
Digital I/O power
- AVDD
Analog power
- DVDD
Digital core power
The addition of these regulators shouldn't affect existing users using
fixed-on/firmware-controlled regulators.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The enable path does
- gpio
- clock
The disable path does
- gpio
- clock
Fix the order on the power-off path so that power-off and power-on have the
same ordering for clock and gpio.
Fixes: 9214e86c0c ("media: i2c: Add imx412 camera sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx412/imx577 sensor has a reset line that is active low not active
high. Currently the logic for this is inverted.
The right way to define the reset line is to declare it active low in the
DTS and invert the logic currently contained in the driver.
The DTS should represent the hardware does i.e. reset is active low.
So:
+ reset-gpios = <&tlmm 78 GPIO_ACTIVE_LOW>;
not:
- reset-gpios = <&tlmm 78 GPIO_ACTIVE_HIGH>;
I was a bit reticent about changing this logic since I thought it might
negatively impact @intel.com users. Googling a bit though I believe this
sensor is used on "Keem Bay" which is clearly a DTS based system and is not
upstream yet.
Fixes: 9214e86c0c ("media: i2c: Add imx412 camera sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
For long term references, frame_num is set to long_term_frame_idx which
does not require wrapping. This is fixed by observation, no directly
related issue have been found yet.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If the timestamp of the src buffer differs from the timestamp of a held
dst buffer, the held buffer is implicitly removed and marked as done.
Add a trace to help debugging if someone hits that case.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add h264 decode driver to support mt8186. For the architecture
is single core, need to add new interface to decode.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for VP9 decoding using the stateless API,
as supported by MT8192. And the drivers is lat and core architecture.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: George Sun <george.sun@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for VP8 decoding using the stateless API,
as supported by MT8192.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Adds h264 lat and core architecture driver for mt8192,
and the decode mode is frame based for stateless decoder.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Mt8192 can use some of common code with mt8183. Moves them to
a new file in order to reuse.
[hverkuil: replaced memcpy_toio by memcpy, was left over from a prev version]
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The capture queue format type may be differ depending on platform: for
stateless decoder drivers, we need to calculate the capture buffer size
according to the capture queue format type in SCP.
As a preparation for introducing drivers for stateless decoding, save the
current capture queue type on a per vcodec context basis.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Need to use default pic info when get pic info fail.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Steve Cho <stevecho@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
For vp8 not support 4K, need to disable it.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Needs to use mediatek compressed mode for mt8192 decoder.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Getting supported output and capture queue format types according
to decoder capability.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Supported output and capture format types for mt8192 are different
with mt8183. Redefine parameters to store them.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
For lat and core decode in parallel, need to get capture buffer
when core start to decode and put capture buffer to display
list when core decode done.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
call vb2_set_plane_payload to set each plane bytesused in buf prepare,
need not to set independently for stateless and statefull architectures.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Supported max resolution for different platforms are not the same: 2K
or 4K, getting it according to dec_capability.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Tzung-Bi Shih<tzungbi@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Different capture buffer format has different buffer size, need to get
real buffer size according to buffer type from scp.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MT8173 platform use vpu firmware, mt8183/mt8192 will use scp
firmware instead, using chip name is not reasonable to separate
different firmware architecture. Using firmware type is much better.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Tzung-Bi Shih<tzungbi@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Lock, power and clock are highly coupled operations. Adds vdec
enable/disable hardware helpers and uses them.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Tzung-Bi Shih<tzungbi@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Will return -EINVAL using standard framework api when test stateless
decoder with cmd VIDIOC_(TRY)DECODER_CMD. Disable them to adjust v4l2
compliance test for user driver(GStreamer/Chrome) won't use decoder cmd.
Fixes: 8cdc3794b2 ("media: mtk-vcodec: vdec: support stateless API")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Using an activation counter to decide when the enable or disable the
cec adapter is not the best approach and can lead to race conditions.
Change this to determining the current status of the adapter, and
enable or disable the adapter accordingly.
It now only needs to be called whenever there is a chance that the
state changes, and it can handle enabling/disabling monitoring as
well if needed.
This simplifies the code and it should be a more robust approach as well.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If the physical address changes (i.e. becomes invalid, then valid again)
while the adapter is still claiming free logical addresses, then trigger
a reconfiguration since any claimed LAs may now be stale.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If an adapter is trying to claim a free logical address then it is
in the 'is_configuring' state. If during that process the cable is
disconnected (HPD goes low, which in turn invalidates the physical
address), then cec_adap_unconfigure() is called, and that set the
is_configuring boolean to false, even though the thread that's
trying to claim an LA is still running.
Don't touch the is_configuring bool in cec_adap_unconfigure(), it
will eventually be cleared by the thread. By making that change
the cec_config_log_addr() function also had to change: it was
aborting if is_configuring became false (since that is what
cec_adap_unconfigure() did), but that no longer works. Instead
check if the physical address is invalid. That is a much
more appropriate check anyway.
This fixes a bug where the the adapter could be disabled even
though the device was still configuring. This could cause POLL
transmits to time out.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If, while trying to claim a free logical address, a POLL message
times out, then abort this process. A CEC_TX_STATUS_TIMEOUT
should be handled the same as a CEC_TX_STATUS_ABORTED.
This avoids a situation where transmits time out due to a
driver or hardware bug and it takes ages before the attempt
to find available free logical addresses finishes.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The __cec_s_log_addrs() function can configure or unconfigure the
adapter. The ioctl handler in cec-api.c will prevent it from being
called to configure the adapter if it was already configured (or in
the process of configuring). But it can still be called to unconfigure
an already unconfigured adapter, and it didn't check for that.
This can cause cec_activate_cnt_dec() to be called too often, causing
a WARN_ON.
Instead first check if adap->log_addrs.num_log_addrs == 0 and return
since in that case the adapter is already unconfigured.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It's OK to keep the pending pin events when disabling or
enabling the 'adapter'. Zeroing this can cause a race condition
if this happens when the pin kthread is handling a pin event
and calls atomic_dec later, causing work_pin_num_events to become
negative.
Just leave pending events in the queue, they'll be read eventually.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When the adap_enable callback is called the adap->lock is held.
When disabling the adapter it attempts to stop the kthread that
deals with receiving and transmitting messages. However, kthread_stop
waits for the thread to stop, so all that time adap->lock is held.
Unfortunately, the kernel thread itself can call functions that take
that same lock, so a deadlock can occur.
Change the logic to keep the kernel thread running and instead when
disabling the adapter, just set the pin to high, go to idle and then
to state OFF and disable the interrupt. Only stop the kernel thread
when the adapter is deleted.
This way disabling the adapter will not wait for anything and the
deadlock is avoided.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Since usb_register_dev() from imon_init_display() from imon_probe() holds
minor_rwsem while display_open() which holds driver_lock and ictx->lock is
called with minor_rwsem held from usb_open(), holding driver_lock or
ictx->lock when calling usb_register_dev() causes circular locking
dependency problem.
Since usb_deregister_dev() from imon_disconnect() holds minor_rwsem while
display_open() which holds driver_lock is called with minor_rwsem held,
holding driver_lock when calling usb_deregister_dev() also causes circular
locking dependency problem.
Sean Young explained that the problem is there are imon devices which have
two usb interfaces, even though it is one device. The probe and disconnect
function of both usb interfaces can run concurrently.
Alan Stern responded that the driver and USB cores guarantee that when an
interface is probed, both the interface and its USB device are locked.
Ditto for when the disconnect callback gets run. So concurrent probing/
disconnection of multiple interfaces on the same device is not possible.
Therefore, we don't need locks for handling race between imon_probe() and
imon_disconnect(). But we still need to handle race between display_open()
/vfd_write()/lcd_write()/display_close() and imon_disconnect(), for
disconnect event can happen while file descriptors are in use.
Since "struct file"->private_data is set by display_open(), vfd_write()/
lcd_write()/display_close() can assume that "struct file"->private_data
is not NULL even after usb_set_intfdata(interface, NULL) was called.
Replace insufficiently held driver_lock with refcount_t based management.
Add a boolean flag for recording whether imon_disconnect() was already
called. Use RCU for accessing this boolean flag and refcount_t.
Since the boolean flag for imon_disconnect() is shared, disconnect event
on either intf0 or intf1 affects both interfaces. But I assume that this
change does not matter, for usually disconnect event would not happen
while interfaces are in use.
Link: https://syzkaller.appspot.com/bug?extid=c558267ad910fc494497
Reported-by: syzbot <syzbot+c558267ad910fc494497@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+c558267ad910fc494497@syzkaller.appspotmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The point of using get/put_device() is to keep references
for as long as the device may be in use. That means dropping
them must be the penultimate action right before freeing the memory.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The timer will report events for an input device.
Reporting events for an unregistered device is bad.
Hence the timer must be killed first.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
GFP_NOIO is fine here.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix smatch warning:
drivers/media/i2c/s5k6a3.c:234 __s5k6a3_power_on() warn: 'sensor->clock' from clk_prepare_enable() not released on lines: 234.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fixes smatch warning:
drivers/media/i2c/ccs/ccs-core.c:1676 ccs_power_on() warn: 'sensor->ext_clk' from clk_prepare_enable() not released on lines: 1606.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fixes smatch warning:
drivers/media/pci/cx25821/cx25821-alsa.c:768 cx25821_audio_initdev() warn: 'dev->pci->irq' from request_irq() not released on lines: 768.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
G/S_PARM doesn't make sense for the capture queue of a stateful encoder,
unless V4L2_FMT_FLAG_ENC_CAP_FRAME_INTERVAL is set to reserve hardware
resources.
Otherwise it will fail the v4l2-compliance
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
when error occurs, driver set error flag,
and driver need to wake up the poll wait
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
With this, the csi2dc will take part in the media pipeline graph walk
and validate the links with it's entities.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Compact the list array to be more readable.
No other changes, only cosmetic.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The AWB workqueue runs in a kernel thread and needs to be synchronized
w.r.t. the streaming status.
It is possible that streaming is stopped while the AWB workq is running.
In this case it is likely that the check for vb2_start_streaming_called is
done at one point in time, but the AWB computations are done later,
including a call to isc_update_profile, which requires streaming to be
started.
Thus , isc_update_profile will fail if during this operation sequence the
streaming was stopped.
To solve this issue, a mutex is added, that will serialize the awb work and
streaming stopping, with the mention that either streaming is stopped
completely including termination of the last frame is done, and after that
the AWB work can check stream status and stop; either first AWB work is
completed and after that the streaming can stop correctly.
The awb spin lock cannot be used since this spinlock is taken in the same
context and using it in the stop streaming will result in a recursion BUG.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
While this does not happen in production, this check should be done
versus the mask, as checking with the YCYC value may not include
some bits that may be set.
It is correct and safe to check the whole mask.
Fixes: 123aaf816b ("media: atmel: atmel-sama5d2-isc: fix YUYV format")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Remove duplicate comments which are already in place before the struct
definition.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In s_fmt_vid_cap, we should check if vb2_is_busy and return EBUSY,
not check if it's streaming to return the busy state.
Suggested-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
During experiments with libcamera, it looks like vb2_is_streaming returns
true before our start streaming is called.
Order of operations is streamon -> queue -> start_streaming
ISC would have started the DMA immediately when a buffer is being added
to the vbqueue if the queue is streaming.
It is more safe to start the DMA after the start streaming of the driver is
called.
Thus, even if vb2queue is streaming, add the buffer to the dma queue of the
driver instead of actually starting the DMA process, if the start streaming
has not been called yet.
Tho achieve this, we have to use vb2_start_streaming_called instead of
vb2_is_streaming.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The vertical subsampling factor is currently not considered in the
offset calculation for plane cropping done in rpf_configure_partition.
This causes a distortion (shift of the color plane) when formats with
the vsub factor larger than 1 are used (e.g. NV12, see
vsp1_video_formats in vsp1_pipe.c). This commit considers vsub factor
for all planes except plane 0 (luminance).
Drop generalization of the offset calculation to reduce the binary size.
Fixes: e5ad37b64d ("[media] v4l: vsp1: Add cropping support")
Signed-off-by: Michael Rodin <mrodin@de.adit-jv.com>
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the new vb2_queue_is_busy() helper to replace the open-coded
version.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the vb2_fop_release() helper to replace the open-coded version. The
video->lock is assigned to the queue lock, used by vb2_fop_release(), so
the only functional difference is that v4l2_fh_release() is now called
before vsp1_device_put(). This should be harmless.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
vb2 queue ownership is managed by the ioctl handler helpers
(vb2_ioctl_*). There are however use cases where drivers can benefit
from checking queue ownership, for instance when open-coding an ioctl
handler that needs to perform additional checks before calling the
corresponding vb2 operation.
Expose the vb2_queue_is_busy() function in the videobuf2-v4l2.h header,
and change its first argument to a struct vb2_queue pointer as the
function name implies it operates on a queue, not a video_device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace the hardcoded MIPI CSI-2 data types with macros from
mipi-csi2.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
the output buffer count should >= min_buffer_out
the capture buffer count should >= min_buffer_cap
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In stk_camera_read_reg() a single byte buffer is alloc-ed and
freed on every function call. Since the size is known,
move the buffer to the struct stk_camera where it will be alloc-ed
and freed once.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Let VIDIOC_ENUM_FRAMEINTERVALS return -EINVAL if userspace queries
frame intervals for frame sizes unsupported by the encoder. Fixes the
following v4l2-compliance failure:
fail: v4l2-test-formats.cpp(123): found frame intervals for invalid size 47x16
fail: v4l2-test-formats.cpp(282): node->codec_mask & STATEFUL_ENCODER
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
[hverkuil: drop incorrect 'For decoder devices, return -ENOTTY.' in the commit log]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Set default colorspace to SRGB for JPEG encoder and decoder devices,
to fix the following v4l2-compliance test failure:
test VIDIOC_TRY_FMT: OK
fail: v4l2-test-formats.cpp(818): fmt_raw.g_colorspace() != V4L2_COLORSPACE_SRGB
Also explicitly set transfer function, YCbCr encoding and quantization
range, as required by v4l2-compliance for the JPEG encoded side.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The resource is checked in probe function, so there is
no need do this check in remove function.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The resource is checked in probe function, so there is
no need do this check in remove function.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The resource is checked in probe function, so there is
no need do this check in remove function.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The video viu driver is not a vital one for booting purposes.
Remove the unneeded 'default y' option.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The typical behavior is to add all controls, then at the end check if
hdl->error was set, and if so, v4l2_ctrl_handler_free is called and
the error is returned.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
For some invalid frames,
especially multiple consecutive invalid frames,
they all can't be decoded,
then the firmware can send picture skipped event
to notify driver that some frames are invalid,
driver can return them with error flag.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
copy the timestamp using the helper function
V4L2_BUF_FLAG_TIMESTAMP_COPY
To implement this, driver will keep the output buffer until it's
encoded, in previous, driver will return the output buffer immediately
after firmware return it
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
copy the timestamp using the helper function
V4L2_BUF_FLAG_TIMESTAMP_COPY
To implement this, driver will keep the output buffer until it's
decoded, in previous, driver will return the output buffer immediately
after copying data to stream buffer.
After that, there is no need to make a workaround for poll function.
driver can use v4l2_m2m_fop_poll directly.
Also, driver don't need to keep a input threshold
as the buffer count is up to only 32.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix build errors when RADIO_TEA575X=y, VIDEO_BT848=m, and VIDEO_DEV=m.
The build errors occur due to [in drivers/media/Makefile]:
obj-$(CONFIG_VIDEO_DEV) += radio/
so the (would be) builtin tea575x.o is not being built.
This is also due to drivers/media/radio/Kconfig declaring a bool
Kconfig symbol (RADIO_ADAPTERS) that depends on a tristate (VIDEO_DEV),
so when VIDEO_DEV=m, RADIO_ADAPTERS becomes =y, and then the drivers
that depend on RADIO_ADPATERS can be configured as builtin (=y) or
as loadable modules (=m).
Fix this by converting RADIO_ADAPTERS to a tristate symbol instead
of a bool symbol.
Fixes these build errors:
ERROR: modpost: "snd_tea575x_hw_init" [drivers/media/pci/bt8xx/bttv.ko] undefined!
ERROR: modpost: "snd_tea575x_set_freq" [drivers/media/pci/bt8xx/bttv.ko] undefined!
ERROR: modpost: "snd_tea575x_s_hw_freq_seek" [drivers/media/pci/bt8xx/bttv.ko] undefined!
ERROR: modpost: "snd_tea575x_enum_freq_bands" [drivers/media/pci/bt8xx/bttv.ko] undefined!
ERROR: modpost: "snd_tea575x_g_tuner" [drivers/media/pci/bt8xx/bttv.ko] undefined!
Link: lore.kernel.org/r/202204191711.IKJJFjgU-lkp@intel.com
Fixes: 9958d30f38 ("media: Kconfig: cleanup VIDEO_DEV dependencies")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Syzbot reported that -1 is used as array index. The problem was in
missing validation check.
hdw->unit_number is initialized with -1 and then if init table walk fails
this value remains unchanged. Since code blindly uses this member for
array indexing adding sanity check is the easiest fix for that.
hdw->workpoll initialization moved upper to prevent warning in
__flush_work.
Reported-and-tested-by: syzbot+1a247e36149ffd709a9b@syzkaller.appspotmail.com
Fixes: d855497edb ("V4L/DVB (4228a): pvrusb2 to kernel 2.6.18")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Remove a stray blank line between function definition and body.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
To support dynamic resolution change,
driver should meet the following conditions:
1. the previous pictures are all decoded before source change event.
2. prevent decoding new resolution pictures with incorrect capture
buffer, until user handle source change event and setup capture.
3. report correct fmt and resolution during source change.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The GStreamer v4l2videodec only ever calls S_FMT on the output side
and then expects G_FMT on the capture side to return a valid format.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The decoder will save the precision that was detected from jpeg header
and use it later, when choosing the pixel format and also calculate
bytesperline according to precision.
The 12bit jpeg is not supported yet,
but driver shouldn't led to serious problem if user enqueue a 12 bit jpeg.
And the 12bit jpeg is supported by hardware, driver may support it later.
[hverkuil: document the new precision field]
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Clang static analysis reports this issue
ispcsiphy.c:63:14: warning: The left operand of '<<'
is a garbage value
reg |= mode << shift;
~~~~ ^
The iface switch-statement default case falls through
to ISP_INTERFACE_CCP2B_PHY1. Which is later checked
to set the mode. Since the default case is left out
of this check mode is never set. Instead of falling
through and assuming a ISP_INTERFACE_CCP2B_PHY1
iface, return.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The corresponding API for clk_prepare_enable is clk_disable_unprepare,
other than clk_disable.
Fix this by changing clk_disable to clk_disable_unprepare.
Fixes: b4155d7d5b ("[media] exynos4-is: Ensure fimc-is clocks are not enabled until properly configured")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
We verified that "vpif_obj.sd[i]" is non-NULL on the previous line so
no need to check here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The "bdisp->clock" variable cannot be an error pointer here. No need to
check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The RDACM20 camera supports a single image format which is currently
listed as MEDIA_BUS_FMT_UYVY8_2X8. As the video stream is transmitted on
the GMSL serial bus, the 2X8 variant does not apply.
Fix the format by using MEDIA_BUS_FMT_UYVY8_1X16.
This fixes a runtime error which is now triggered as the MAX9286
deserializer implements .link_validate().
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a check to make sure the input interface (CSI-2 or parallel) allow
for the requested input bus format. If not inform the user and error out
rather then try to continue with incorrect settings.
While at it add the missing define for RGB666 that is not yet supported
in the driver but we can preemptively check for it in this context
already.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The v4l2_m2m_dev structure documentation incorrectly references the
v4l2_m2m_unregister_media_controller() function when it actually means
v4l2_m2m_register_media_controller(). Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
smb_word_op() has a parameter data_format that
determines if the data is either a byte or
word. From inspection, smb_word_op() is only
used by the macros smb_wr16() and smb_rd16()
both pass in CMD_WORD_DATA. There is no use of
smb_word_op() that passes in CMD_BYTE_DATA.
So remove the byte handling.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The subdevice entity function was left unset, which produces a warning
when probing the device:
mxc-md bus@58000000📷 Entity type for entity rdacm20 19-0051 was
not initialized!
This patch will set entity function to MEDIA_ENT_F_CAM_SENSOR and leave
flags unset.
Fixes: 34009bffc1 ("media: i2c: Add RDACM20 driver")
Fixes: a59f853b3b ("media: i2c: Add driver for RDACM21 camera module")
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Don't populate the read-only array table on the stack but
instead make it static const. Also makes the object code a little
smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The pm_runtime_enable will decrease power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable().
Fixes: 0a0e265515 ("media: atmel: atmel-isc: split driver into driver base and isc")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The pm_runtime_enable will decrease power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable().
Fixes: f386509e49 ("[media] st-delta: STiH4xx multi-format video decoder v4l2 driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Acked-by: Hugues Fruchet <hugues.fruchet@foss.st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call.
Fixes: 9a761e4368 ("[media] exynos4-is: Add Exynos4x12 FIMC-IS driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
A dma_free_coherent() call is missing in the error handling path of the
probe, as already done in the remove function.
In fact, this call is included in aspeed_video_free_buf(). So use the
latter both in the error handling path of the probe and in the remove
function.
It is easier to see the relation with aspeed_video_alloc_buf() this way.
Fixes: d2b4387f3b ("media: platform: Add Aspeed Video Engine driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This patch aims to add UVC_GUID_FORMAT_H265
High Efficiency Video Coding (HEVC), also known as H.265 and MPEG-H Part 2.
They describe the same video encoding method.
So for handling their behavior is the same.
However, when external camera device describes this encoding method,
some use hevc, some use h265.
There is no uniform specification to describe this encoding method.
So if an external camera device use h265 to describe this encoding method,
driver will not recognize it.
Therefore, this patch is to enable driver to read HEVC/H265
and convert it to V4L2_PIX_FMT_HEVC.
Signed-off-by: James_Lin <Ping-lei.Lin@mediatek.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace manual decoding of psize in uvc_parse_streaming(), with the code
from uvc_endpoint_max_bpi(). It also handles usb3 devices.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The case USB_SPEED_WIRELESS and the default one were doing the same.
Also, make always use of usb_endpoint_maxp_mult, as it should have a
sane value, even for LOW speed and WIRELESS.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move all the life cycle of the name to add_mapping. This simplifies
the error handling inside uvc_ioctl_ctrl_map and solves a memory leak
when kemmdup fails.
Also make sure that for custom controls, the user provides a valid name.
Fixes: 07adedb5c606 ("media: uvcvideo: Use control names from framework")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
probe->dwMaxPayloadTransferSize is a 32bit value, but bandwidth is 16bit. This
may lead to a bit overflow.
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The list iterator will point to a bogus position containing HEAD if
the list is empty or the element is not found in list. This case
should be checked before any use of the iterator, otherwise it will
lead to a invalid memory access. The missing check here is before
"pin = iterm->id;", just add check here to fix the security bug.
In addition, the list iterator value will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the iterator
value will be NULL if the element is not found in list, considering
the (mis)use here: "if (iterm == NULL".
Use a new value 'it' as the list iterator, while use the old value
'iterm' as a dedicated pointer to point to the found element, which
1. can fix this bug, due to 'iterm' is NULL only if it's not found.
2. do not need to change all the uses of 'iterm' after the loop.
3. can also limit the scope of the list iterator 'it' *only inside*
the traversal loop by simply declaring 'it' inside the loop in the
future, as usage of the iterator outside of the list_for_each_entry
is considered harmful. https://lkml.org/lkml/2022/2/17/1032
Fixes: d5e90b7a6c ("[media] uvcvideo: Move to video_ioctl2")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As discussed with other developers, the linux-uvc-devel mailing list is
not very useful anymore, and it's better to send people to the general
linux-media mailing list.
Replace/remove the old mailing list address in uvcvideo.rst and
MAINTAINERS.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Do not handroll mdelay().
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmJu9FYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAyEH/16xtJSpLmLwrQzG
o+4ToQxSQ+/9UHyu0RTEvHg2THm9/8emtIuYyc/5FgdoWctcSa3AaDcveWmuWmkS
KYcdhfJsaEqjNHS3OPYXN84fmo9Hel7263shu5+IYmP/sN0DfQp6UWTryX1q4B3Q
4Pdutkuq63Uwd8nBZ5LXQBumaBrmkkuMgWEdT4+6FOo1mPzwdIGBxCuz1UsNNl5k
chLWxkQfe2eqgWbYJrgCQfrVdORXVtoU2fGilZUNrHRVGkkldXkkz5clJfapyZD3
odmZCEbrE4GPKgZwCmDERMfD1hzhZDtYKiHfOQ506szH5ykJjPBcOjHed7dA60eB
J3+wdek=
=39Ca
-----END PGP SIGNATURE-----
Merge 5.18-rc5 into usb-next
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-04-27
We've added 85 non-merge commits during the last 18 day(s) which contain
a total of 163 files changed, 4499 insertions(+), 1521 deletions(-).
The main changes are:
1) Teach libbpf to enhance BPF verifier log with human-readable and relevant
information about failed CO-RE relocations, from Andrii Nakryiko.
2) Add typed pointer support in BPF maps and enable it for unreferenced pointers
(via probe read) and referenced ones that can be passed to in-kernel helpers,
from Kumar Kartikeya Dwivedi.
3) Improve xsk to break NAPI loop when rx queue gets full to allow for forward
progress to consume descriptors, from Maciej Fijalkowski & Björn Töpel.
4) Fix a small RCU read-side race in BPF_PROG_RUN routines which dereferenced
the effective prog array before the rcu_read_lock, from Stanislav Fomichev.
5) Implement BPF atomic operations for RV64 JIT, and add libbpf parsing logic
for USDT arguments under riscv{32,64}, from Pu Lehui.
6) Implement libbpf parsing of USDT arguments under aarch64, from Alan Maguire.
7) Enable bpftool build for musl and remove nftw with FTW_ACTIONRETVAL usage
so it can be shipped under Alpine which is musl-based, from Dominique Martinet.
8) Clean up {sk,task,inode} local storage trace RCU handling as they do not
need to use call_rcu_tasks_trace() barrier, from KP Singh.
9) Improve libbpf API documentation and fix error return handling of various
API functions, from Grant Seltzer.
10) Enlarge offset check for bpf_skb_{load,store}_bytes() helpers given data
length of frags + frag_list may surpass old offset limit, from Liu Jian.
11) Various improvements to prog_tests in area of logging, test execution
and by-name subtest selection, from Mykola Lysenko.
12) Simplify map_btf_id generation for all map types by moving this process
to build time with help of resolve_btfids infra, from Menglong Dong.
13) Fix a libbpf bug in probing when falling back to legacy bpf_probe_read*()
helpers; the probing caused always to use old helpers, from Runqing Yang.
14) Add support for ARCompact and ARCv2 platforms for libbpf's PT_REGS
tracing macros, from Vladimir Isaev.
15) Cleanup BPF selftests to remove old & unneeded rlimit code given kernel
switched to memcg-based memory accouting a while ago, from Yafang Shao.
16) Refactor of BPF sysctl handlers to move them to BPF core, from Yan Zhu.
17) Fix BPF selftests in two occasions to work around regressions caused by latest
LLVM to unblock CI until their fixes are worked out, from Yonghong Song.
18) Misc cleanups all over the place, from various others.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (85 commits)
selftests/bpf: Add libbpf's log fixup logic selftests
libbpf: Fix up verifier log for unguarded failed CO-RE relos
libbpf: Simplify bpf_core_parse_spec() signature
libbpf: Refactor CO-RE relo human description formatting routine
libbpf: Record subprog-resolved CO-RE relocations unconditionally
selftests/bpf: Add CO-RE relos and SEC("?...") to linked_funcs selftests
libbpf: Avoid joining .BTF.ext data with BPF programs by section name
libbpf: Fix logic for finding matching program for CO-RE relocation
libbpf: Drop unhelpful "program too large" guess
libbpf: Fix anonymous type check in CO-RE logic
bpf: Compute map_btf_id during build time
selftests/bpf: Add test for strict BTF type check
selftests/bpf: Add verifier tests for kptr
selftests/bpf: Add C tests for kptr
libbpf: Add kptr type tag macros to bpf_helpers.h
bpf: Make BTF type match stricter for release arguments
bpf: Teach verifier about kptr_get kfunc helpers
bpf: Wire up freeing of referenced kptr
bpf: Populate pairs of btf_id and destructor kfunc in btf
bpf: Adapt copy_map_value for multiple offset case
...
====================
Link: https://lore.kernel.org/r/20220427224758.20976-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no need to pass 'default n' in Kconfig, as by default the
CONFIG_VIDEO_IMX_MIPI_CSIS option is not selected.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit 5c0701a0e7 ("media: imx: csis: Store pads format separately")
broke initialization of the active format on the source pad, as it
forgot to update the .init_cfg() handler. Fix it.
Fixes: 5c0701a0e7 ("media: imx: csis: Store pads format separately")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The mipi_csis_dump_regs() function accesses the interface registers
in order to printout their values for debug purposes.
As the function access the registers, it requires the interface to be
powered up. Currently this is only enforced in one of the function's
callers (mipi_csis_log_status)() but not when the function is called by
the debugfs attribute handler.
Make sure to access registers only if the interface is powered up and
remove the same check from the caller.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The mipi_csis_device.powered flag only serves for the purpose of
not accessing registers in mipi_csis_log_status() when the interface
is not powered up.
Instead of manually tracking the power state, rely on
pm_runtime_get_if_in_use() to remove the 'powered' flag. Also remove
the locking in the function as runtime_pm() is refcounted and there's no
risk of the interface being powered down behind our backs.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Simplify the mipi_csis_s_stream() function.
This actually fixes a bug, as if calling the subdev's s_stream(1) fails,
mipi_csis_stop_stream() was not called.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The runtime PM resume handler is guaranteed to be called on a suspended
device, and the suspend handler on a resumed device. The implementation
can thus be simplified.
While at it, rename the mipi_csis_device state field to powered, as the
now state contains a single flag only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Streaming is guaranteed to have been stopped by the time the device gets
runtime suspended, as pm_runtime_put() is called from .s_stream(0) only.
Drop the manual stop.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There's no need to implement system suspend/resume manually, as video
pipelines are supposed to be suspended in a controlled and ordered
manner by the data sink driver at system suspend time (and similarly at
resume time). Drop the system suspend/resume handlers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The subdev .s_power() operation is deprecated. Drop it, requiring sensor
drivers to correctly use runtime PM instead of relying on .s_power().
As this driver has just been moved out of staging, and necessary drivers
to implement a full camera pipeline are still in staging, no platform
depends yet on this API being called. There is thus no risk of
regression.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Usage of "state" for the device-specific data structure is confusing, as
it can also refer to the subdev state. Rename the structure to
mipi_csis_device, and the corresponding state variables to csis.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
For interlaced frame, the amphion vpu will store the
two fields sequential into one buffer, top-bottom order
so the field should be set to V4L2_FIELD_SEQ_TB.
fix the previous bug that set it to V4L2_FIELD_SEQ_BT wrongly.
Fixes: 6de8d628df ("media: amphion: add v4l2 m2m vpu decoder stateful driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
use if and else instead of if(A) and if (!A).
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Don't change the output buffer's bytesused set by user.
Drop allow_zero_bytesused, since it's deprecated.
This should also guarantee it's the application's responsibility
to set bytesused for the output buffer.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When the driver fails to call the dma_set_mask(), the driver will get
the following splat:
[ 55.853884] BUG: KASAN: use-after-free in __process_removed_driver+0x3c/0x240
[ 55.854486] Read of size 8 at addr ffff88810de60408 by task modprobe/590
[ 55.856822] Call Trace:
[ 55.860327] __process_removed_driver+0x3c/0x240
[ 55.861347] bus_for_each_dev+0x102/0x160
[ 55.861681] i2c_del_driver+0x2f/0x50
This is because the driver has initialized the i2c related resources
in cx23885_dev_setup() but not released them in error handling, fix this
bug by modifying the error path that jumps after failing to call the
dma_set_mask().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Declaring variable "tuner_status" without initializer.
Using uninitialized value "tuner_status" when calling
"*fe_tuner_ops->get_status".
(The function pointer resolves to "cx24113_get_status".)
Signed-off-by: Yan Lei <yan_lei@dahuatech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add H264 level 1.0, 4.1, 4.2 to the list of supported formats.
While the hardware does not fully support these levels, it does support
most of them. The constraints on frame size and pixel formats already
cover the limitation.
This fixes negotiation of level on GStreamer 1.17.1.
Cc: stable@vger.kernel.org
Fixes: 42a68012e6 ("media: coda: add read-only h.264 decoder profile/level controls")
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The CODA960 manual states that ASO/FMO features of baseline are not
supported, so for this reason this driver should only report
constrained baseline support.
This fixes negotiation issue with constrained baseline content
on GStreamer 1.17.1.
ASO/FMO features are unsupported for the encoder and untested for the
decoder because there is currently no userspace support. Neither GStreamer
parsers nor FFMPEG parsers support ASO/FMO.
Cc: stable@vger.kernel.org
Fixes: 42a68012e6 ("media: coda: add read-only h.264 decoder profile/level controls")
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Pascal Speck <kernel@iktek.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The hardware is capable of encoding/decoding RGB and ARGB formats
in whatever order the color components are,
but the resulting jpegs look good
if we start with raw data in BGR/ABGR order,
so we will further only support V4L2_PIX_FMT_BGR24 and V4L2_PIX_FMT_ABGR32.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Wait finishing jpeg job before system sleep,
otherwise the encoding/decoding can't be resumed after suspend.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Stop bailing out on JPEG header parsing errors during streamon.
This allows userspace to provide valid output buffers later and
fixes a v4l2-compliance streaming test failure:
fail: v4l2-test-buffers.cpp(1429): node->streamon(q.g_type())
test MMAP (no poll): FAIL
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If JPEG header parsing fails, output a single message instead of two
messages that say the same thing.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If decoding fails because the output buffer does not contain a
valid header, set the error flag on the returned capture buffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The JPEG decoder in the CODA960 VPU can downscale images while decoding,
with a factor of 1/2, 1/4, or 1/8.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The variable m is being assigned a value that is never read, it
is being re-assigned in both paths of the following if-statement.
The assignment is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If the decoder prepare_run callback returns an error, the hardware
is never started and v4l2_m2m_job_finish() is called immediately,
currently in every error path.
Remove the duplicated job_finish calls from the error paths and reuse
the v4l2_m2m_job_finish() at the end of coda_pic_run_work instead.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
coda_fill_bitstream() must be called under the bitstream mutex.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use v4l2_disable_ioctl() to disable the stateful encoder ioctls
VIDIOC_ENUM_FRAMEINTERVALS, VIDIOC_G_PARM, and VIDIOC_S_PARM for
the jpeg encoder device, to fix this v4l2-compliance test failure:
fail: v4l2-test-formats.cpp(68): node->is_m2m && !(node->codec_mask & STATEFUL_ENCODER)
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
fail: v4l2-test-formats.cpp(1363): node->is_m2m && !is_stateful_enc
test VIDIOC_G/S_PARM: FAIL
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use v4l2_disable_ioctl() to disable the encoder ioctls
VIDIOC_ENUM_FRAMESIZES, VIDIOC_ENUM_FRAMEINTERVALS, VIDIOC_G_PARM, and
VIDIOC_S_PARM, to fix this v4l2-compliance test failure:
fail: v4l2-test-formats.cpp(1363): node->is_m2m && !is_stateful_enc
test VIDIOC_G/S_PARM: FAIL
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use v4l2_disable_ioctl() to disable the VIDIOC_TRY_ENCODER_CMD and
VIDIOC_ENCODER_CMD ioctls on decoder video devices and the
VIDIOC_TRY_DECODER_CMD and VIDIOC_DECODER_CMD ioctls on encoder
video devices.
This allows to drop the coda_try_encoder/decoder_cmd() functions
and to use v4l2_m2m_ioctl_try_encoder/decoder_cmd() directly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a control to set intra-refresh type.
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When recalculate output buffer size we have to take into account
the output resolution from the firmware received during event change
notification.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This adds QC10C compressed pixel format in the Venus driver, and
make it possible to discover from v4l2 clients.
Note: The QC10C format will be enumerable via VIDIOC_ENUM_FMT when
the bitstream is 10-bits and the headers are parsed.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This adds QC08C compressed pixel format in the Venus driver, and
make it possible to discover from v4l2 clients.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a helper to check supported pixel format per codec and session
type.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add custom Qualcomm raw compressed pixel formats. They are
used in Qualcomm SoCs to optimize the interconnect bandwidth.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Video decoder driver auto-suspends the hardware if there is no
exchange of command or response for certain amount of time.
In auto suspended state, it becomes mandatory to power on the
hardware before requesting it to process a command. The fix
ensures the hardware is powered on during stop streaming.
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
During reconfig (DRC) event from firmware, it is not guaranteed that
all the DPB(internal) buffers would be released by the firmware. Some
buffers might be released gradually while processing frames from the
new sequence. These buffers now stay idle in the dpblist.
In subsequent call to queue the DPBs to firmware, these idle buffers
should not be queued. The fix identifies those buffers and free them.
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If venus_probe fails at pm_runtime_put_sync the error handling first
calls hfi_destroy and afterwards hfi_core_deinit. As hfi_destroy sets
core->ops to NULL, hfi_core_deinit cannot call the core_deinit function
anymore.
Avoid this null pointer derefence by skipping the call when necessary.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This error can appear with wrong configuration and is difficult to find
as it just returns -ETIMEDOUT with no further message.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Simplify the mux error path a bit by using dev_err_probe().
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The only effect of returning an error code in an i2c remove callback is
that the i2c core emits a generic warning and still removes the device.
So even if disabling the regulator fails it's sensible to further cleanup
and then return zero to only emit a single error message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When the driver fails to probe, we will get the following splat:
[ 59.305988] ------------[ cut here ]------------
[ 59.306417] WARNING: CPU: 2 PID: 395 at drivers/regulator/core.c:2257 _regulator_put+0x3ec/0x4e0
[ 59.310345] RIP: 0010:_regulator_put+0x3ec/0x4e0
[ 59.318362] Call Trace:
[ 59.318582] <TASK>
[ 59.318765] regulator_put+0x1f/0x30
[ 59.319058] devres_release_group+0x319/0x3d0
[ 59.319420] i2c_device_probe+0x766/0x940
Fix this by disabling the regulator in error handling.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Currently, the driver ends the reg-val list with a 0xFF as a check to stop
the loop. Instead an array of reg-vals can be used to avoid this check,
by using the ARRAY_SIZE(arr) macro to obtain the length of the array and
iterate over it.
Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This reverts commit c09d776eaa.
Revert the commit as it breaks runtime PM support on OF based systems.
More fixes to the driver are needed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add v4l2_subdev_get_fmt() helper function which implements
v4l2_subdev_pad_ops.get_fmt using active state. Subdev drivers that
support active state and do not need to do anything special in their
get_fmt op can use this helper directly for v4l2_subdev_pad_ops.get_fmt.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It is common that media drivers call subdev ops in source subdevs, and
pass NULL as the state. This was the way to indicate that the callee
should use the callee's private active state.
E.g.:
v4l2_subdev_call(priv->source_sd, pad, get_fmt, NULL, &sd_fmt);
Now that we have a real subdev active state in the v4l2_subdev struct,
we want the caller to pass a proper state (when available). And
furthermore, the state should be locked.
This would mean changing all the callers, which is the long term goal.
To fix this issue in the short term, let's add an extra wrapper layer to
all v4l2_subdev_call_pad_wrappers which deal with states. These wrappers
handle the state == NULL case by using the locked active state instead
(when available).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The V4L2 subdevs have managed without centralized locking for the state
(previously pad_config), as the try-state is supposedly safe (although I
believe two TRY ioctls for the same fd would race), and the
active-state, and its locking, is managed by the drivers internally.
We now have active-state in a centralized position, and need locking.
Strictly speaking the locking is only needed for new drivers that use
the new state, as the current drivers continue behaving as they used to.
However, active-state locking is complicated by the fact that currently
the real active-state of a subdev is split into multiple parts: the new
v4l2_subdev_state, subdev control state, and subdev's internal state.
In the future all these three states should be combined into one state
(the v4l2_subdev_state), and then a single lock for the state should be
sufficient.
But to solve the current split-state situation we need to share locks
between the three states. This is accomplished by using the same lock
management as the control handler does: we use a pointer to a mutex,
allowing the driver to override the default mutex. Thus the driver can
do e.g.:
sd->state_lock = sd->ctrl_handler->lock;
before calling v4l2_subdev_init_finalize(), resulting in sharing the
same lock between the states and the controls.
The locking model for active-state is such that any subdev op that gets
the state as a parameter expects the state to be already locked by the
caller, and expects the caller to release the lock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
At the moment when a subdev op is called, the TRY subdev state
(subdev_fh->state) is passed as a parameter even for the ACTIVE case, or
alternatively a NULL can be passed for ACTIVE case. This used to make
sense, as the ACTIVE state was handled internally by the subdev drivers.
We now have a state for the ACTIVE case in a standard place, and can
pass that also to the drivers. This patch changes the subdev ioctls to
either pass the TRY or ACTIVE state to the subdev.
Unfortunately many drivers call ops from other subdevs, and implicitly
pass NULL as the state, so this is just a partial solution. A coccinelle
spatch could perhaps be created which fixes the drivers' subdev calls.
For all current upstream drivers this doesn't matter, as they do not
expect to get a valid state for ACTIVE case. But future drivers which
support multiplexed streaming and routing will depend on getting a state
for both active and try cases.
For new drivers we can mandate that the pipelines where the drivers are
used need to pass the state properly, or preferably, not call such
subdev ops at all.
However, if an existing subdev driver is changed to support multiplexed
streams, the driver has to consider cases where its ops will be called
with NULL state. The problem can easily be solved by using the
v4l2_subdev_lock_and_get_active_state() helper, introduced in a follow
up patch.
Another follow up patch adds wrappers for pad ops dealing with subdev
state, which automate the use of
v4l2_subdev_lock_and_get_active_state() for cases where the state is
NULL.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a new 'active_state' field to struct v4l2_subdev to which we can
store the active state of a subdev. This will place the subdev
configuration into a known place, allowing us to use the state directly
from the v4l2 framework, thus simplifying the drivers.
Also add functions v4l2_subdev_init_finalize() and
v4l2_subdev_cleanup(), which will allocate and free the active state.
The functions are named in a generic way so that they can be also used
for other subdev initialization work.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
v4l2_subdev_alloc_state() and v4l2_subdev_free_state() are not supposed
to be used by the drivers. However, we do have a few drivers that use
those at the moment, so we need to expose these functions for the time
being.
Prefix the functions with __ to mark the functions as internal.
At the same time, rename them to v4l2_subdev_state_alloc and
v4l2_subdev_state_free to match the style used for other functions like
video_device_alloc() and media_request_alloc().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
subdev_open() is inside #ifdef CONFIG_VIDEO_V4L2_SUBDEV_API, which
depends on CONFIG_MEDIA_CONTROLLER, so there's no need for an extra
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5645 driver reports as its unique supported format
MEDIA_BUS_FMT_UYVY8_2X8, which is not correct as the sensor
uses the MIPI CSI-2 serial bus.
Fix that by using MEDIA_BUS_FMT_UYVY8_1X16 instead.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
media_gobj_destroy has already set graph_obj.mdev to NULL. There is no
need to set it again.
[Sakari Ailus: Remove extra newline, rewrap commit msg]
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Matching on device fwnode handles is deprecated in favour of endpoint
fwnode handles. Switch the __v4l2_async_nf_add_fwnode_remote() function
to use the latter. The match code handles backward compatibility by
falling by to the device fwnode handle, so this shouldn't introduce any
regression.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The bus_info field is set by most drivers based on the type of the device
bus as well as the name of the device. Do this in v4l_querycap() so
drivers don't need to. This keeps compatibility with non-default and silly
bus_info.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Set bus_info field based on struct device in media_device_init() and
remove corresponding code from drivers.
Also update media_device_init() documentation: the dev field must be now
initialised before calling it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Remove redundant kerneldoc documentation in mc-device.c. The functions are
already documented in media-device.h, where non-redundant documentation is
also moved.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use an unsigned int to index an array instead of a signed one.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use %u for printing unsigned integer or u32 values. In a lot of cases %d
was being used instead.
Also remove an extra debug print --- the number of lanes is already
printed by V4L2 when parsing fwnode endpoints when dynamic debug is
enabled.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Upon an async fwnode match, there's some typical behaviour that the
notifier and matching subdev will want to do. For example, a notifier
representing a sensor matching to an async subdev representing its
VCM will want to create an ancillary link to expose that relationship
to userspace.
To avoid lots of code in individual drivers, try to build these links
within v4l2 core.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add functions to create ancillary links, so that they don't need to
be manually created by users.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now we have three types of media link, printing the right name during
debug output is slightly more complicated. Add a helper function to
make it easier.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When iterating over the media graph, don't follow links that are not
data links.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The original implementation removes reverse links for any input link and
assumes the presense of sink/source.
It fails when the link is a not a data link.
media_entity_remove_links when there's an ancillary link can also fail.
We only need to remove reverse links for a data link.
Signed-off-by: Yunke Cao <yunkec@google.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for MEDIA_BUS_FMT_JPEG_1X8 media bus code to the
CSIS driver.
The MEDIA_BUS_FMT_JPEG_1X8 code is mapped to the RAW8 CSI-2 Data Type,
while the CSI-2 specification suggests to use User Defined Data Type 1.
As reported in the comment, the CSIS interface captures arbitrary Data
Types by using a pixel sampling mode not supported by the IP core
connected to it on i.MX SoCs.
As some sensors, such as OV5640, support sending JPEG data on the RAW8
Data Type and capture operations work correcty with such configuration,
map MEDIA_BUS_FMT_JPEG_1X8 to Data Type 0x2a.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This new optional callback is called when the adapter is fully configured
or fully unconfigured. Some drivers may have to take action when this
happens.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Allow drivers to change the transmit timeout value, i.e. after how
long should a transmit be considered 'lost', i.e. the corresponding
cec_transmit_done_ts was never called.
Some CEC devices have their own timeout, and so this timeout value must be
longer than that hardware timeout value. If it is shorter then the
framework would consider the transmit lost, even though it is effectively
still in progress at the hardware level.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use call_(void_)op consistently in the CEC core framework. Ditto
for the cec pin ops. And check if !adap->devnode.unregistered before
calling each op. This avoids calls to ops when the device has been
unregistered and the underlying hardware may be gone.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The results of non-blocking transmits were not correctly communicated
to userspace.
Specifically:
1) if a non-blocking transmit was canceled, then rx_status wasn't set to 0
as it should.
2) if the non-blocking transmit succeeded, but the corresponding reply
never arrived (aborted or timed out), then tx_status wasn't set to 0
as it should, and rx_status was hardcoded to ABORTED instead of the
actual reason, such as TIMEOUT. In addition, adap->ops->received() was
never called, so drivers that want to do message processing themselves
would not be informed of the failed reply.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If a transmit-in-progress was canceled, then, once the transmit
is done, mark it as aborted and refrain from retrying the transmit.
To signal this situation the new transmit_in_progress_aborted field is
set to true.
The old implementation would just set adap->transmitting to NULL and
set adap->transmit_in_progress to false, but on the hardware level
the transmit was still ongoing. However, the framework would think
the transmit was aborted, and if a new transmit was issued, then
it could overwrite the HW buffer containing the old transmit with the
new transmit, leading to garbled data on the CEC bus.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Don't enable/disable the adapter if the first fh is opened or the
last fh is closed, instead do this when the adapter is configured
or unconfigured, and also when we enter Monitor All or Monitor Pin
mode for the first time or we exit the Monitor All/Pin mode for the
last time.
However, if needs_hpd is true, then do this when the physical
address is set or cleared: in that case the adapter typically is
powered by the HPD, so it really is disabled when the HPD is low.
This case (needs_hpd is true) was already handled in this way, so
this wasn't changed.
The problem with the old behavior was that if the HPD goes low when
no fh is open, and a transmit was in progress, then the adapter would
be disabled, typically stopping the transmit immediately which
leaves a partial message on the bus, which isn't nice and can confuse
some adapters.
It makes much more sense to disable it only when the adapter is
unconfigured and we're not monitoring the bus, since then you really
won't be using it anymore.
To keep track of this store a CEC activation count and call adap_enable
only when it goes from 0 to 1 or back to 0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Remove dev_err() messages after platform_get_irq*() failures.
platform_get_irq() already prints an error.
Generated by: scripts/coccinelle/api/platform_get_irq.cocci
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The third argument of usb_maxpacket(): in_out has been deprecated
because it could be derived from the second argument (e.g. using
usb_pipeout(pipe)).
N.B. function usb_maxpacket() was made variadic to accommodate the
transition from the old prototype with three arguments to the new one
with only two arguments (so that no renaming is needed). The variadic
argument is to be removed once all users of usb_maxpacket() get
migrated.
CC: Sean Young <sean@mess.org>
CC: Mauro Carvalho Chehab <mchehab@kernel.org>
CC: Benjamin Valentin <benpicco@googlemail.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20220317035514.6378-5-mailhol.vincent@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7d08c2c911 ("bpf: Refactor BPF_PROG_RUN_ARRAY family of macros
into functions") switched a bunch of BPF_PROG_RUN macros to inline
routines. This changed the semantic a bit. Due to arguments expansion
of macros, it used to be:
rcu_read_lock();
array = rcu_dereference(cgrp->bpf.effective[atype]);
...
Now, with with inline routines, we have:
array_rcu = rcu_dereference(cgrp->bpf.effective[atype]);
/* array_rcu can be kfree'd here */
rcu_read_lock();
array = rcu_dereference(array_rcu);
I'm assuming in practice rcu subsystem isn't fast enough to trigger
this but let's use rcu API properly.
Also, rename to lower caps to not confuse with macros. Additionally,
drop and expand BPF_PROG_CGROUP_INET_EGRESS_RUN_ARRAY.
See [1] for more context.
[1] https://lore.kernel.org/bpf/CAKH8qBs60fOinFdxiiQikK_q0EcVxGvNTQoWvHLEUGbgcj1UYg@mail.gmail.com/T/#u
v2
- keep rcu locks inside by passing cgroup_bpf
Fixes: 7d08c2c911 ("bpf: Refactor BPF_PROG_RUN_ARRAY family of macros into functions")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20220414161233.170780-1-sdf@google.com
