The cpufreq subsystem has a generic sysfs interface for controlling boost
(/sys/devices/system/cpu/cpufreq/boost).
The sysfs interface can be used to enable boost control from the cpupower
command on non-x86 platforms as well. So, allow boost controlling
on non-x86 system if boost sysfs file exists.
The set subcommand enables/disables the boost feature using the following
syntax:
cpupower set --boost 1
cpupower set --boost 0
The --boost option is an alias for --turbo-boost. We provided the neutral
option name because the name "turbo boost" is specific to Intel technology.
The frequency-info subcommand displays the enabled/disabled state of
the boost feature as follows:
boost state support:
Active: yes (or no)
Link: https://lore.kernel.org/r/20250522061122.2149188-3-fj5851bi@fujitsu.com
Signed-off-by: Shinji Nomoto <fj5851bi@fujitsu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The set subcommand's -t option is documented as being available for boost
configuration, but it was not actually functioning due to a bug
in the option handling.
Link: https://lore.kernel.org/r/20250522061122.2149188-2-fj5851bi@fujitsu.com
Signed-off-by: Shinji Nomoto <fj5851bi@fujitsu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
After the commit 0014f65e3d ("pm: cpupower: remove hard-coded
topology depth values"), "cpupower monitor" output ceased to print the
CORE and the CPU fields on a multi-socket platform.
The reason for this is that the patch changed the behaviour to break
out of the switch-case after printing the PKG details, while prior to
the patch, the CORE and the CPU details would also get printed since
the "if" condition check would pass for any level whose topology depth
was lesser than that of a package.
Fix this ensuring all the details below a desired topology depth are
printed in the cpupower monitor output.
Link: https://lore.kernel.org/r/20250612122355.19629-3-gautham.shenoy@amd.com
Fixes: 0014f65e3d ("pm: cpupower: remove hard-coded topology depth values")
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
In the function mperf_start(), mperf_monitor snapshots the time, tsc
and finally the aperf,mperf MSRs. However, this order of snapshotting
in is reversed in mperf_stop(). As a result, the C0 residency (which
is computed as delta_mperf * 100 / delta_tsc) is under-reported on
CPUs that is 100% busy.
Fix this by snapshotting time, tsc and then aperf,mperf in
mperf_stop() in the same order as in mperf_start().
Link: https://lore.kernel.org/r/20250612122355.19629-2-gautham.shenoy@amd.com
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
cmd_monitor() calls get_cpu_topology() to allocate memory for
cpu topology and fails to release in error legs.
Fix it to call cpu_topology_release() from error legs.
Link: https://lore.kernel.org/r/20250305225342.19447-2-skhan@linuxfoundation.org
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
In the case that we give a invalid command to idle_monitor for
monitoring, the execvp() will fail and thus go to the next line.
As a result, we'll see two differnt monitoring output. For
example, running `cpupower monitor -i 5 invalidcmd` which `invalidcmd`
is not executable.
Link: https://lore.kernel.org/r/20250220163846.2765-1-s921975628@gmail.com
Signed-off-by: Yiwei Lin <s921975628@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The amd-pstate section is grouped under boost, which isn't appropriate.
Adjust the indentation so that it is it's own section.
Link: https://lore.kernel.org/r/20241218191144.3440854-8-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
When EPP has been enabled the hardware will autonomously change
frequencies on it's own and thus there is no latency with changing
from the kernel.
Avoid doing the maximum latency check when EPP is found. This will
apply to both amd-pstate and intel-pstate drivers.
Link: https://lore.kernel.org/r/20241218191144.3440854-7-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The EPP value is useful for characterization of performance. Show
it in cpupower frequency-info output.
Link: https://lore.kernel.org/r/20241218191144.3440854-6-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
When the amd-pstate is in use frequency is set by the hardware and
measured by the kernel through using the aperf and mperf registers.
There is no direct call to the hardware to indicate current frequency.
Detect that this feature is in use and skip the check.
Link: https://lore.kernel.org/r/20241218191144.3440854-5-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The rankings are useful information to determine if the scheduler
is placing tasks appropriately for the hardware.
Link: https://lore.kernel.org/r/20241218191144.3440854-4-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
print_duration() has a return; statement at the end of the function
that is not necessary as it's a void function.
Link: https://lore.kernel.org/r/20241218191144.3440854-2-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Commit 'cpupower: Make TSC read per CPU for Mperf monitor' (c2adb1877b)
changes TSC counter reads per cpu, but left time diff global (from start
of all cpus to end of all cpus), thus diff(time) is too large for a
cpu's tsc counting, resulting in far less than acutal TSC_Mhz and thus
`cpupower monitor` showing far less than actual cpu realtime frequency.
/proc/cpuinfo shows frequency:
cat /proc/cpuinfo | egrep -e 'processor' -e 'MHz'
...
processor : 171
cpu MHz : 4108.498
...
before fix (System 100% busy):
| Mperf || Idle_Stats
CPU| C0 | Cx | Freq || POLL | C1 | C2
171| 0.77| 99.23| 2279|| 0.00| 0.00| 0.00
after fix (System 100% busy):
| Mperf || Idle_Stats
CPU| C0 | Cx | Freq || POLL | C1 | C2
171| 0.46| 99.54| 4095|| 0.00| 0.00| 0.00
Fixes: c2adb1877b ("cpupower: Make TSC read per CPU for Mperf monitor")
Signed-off-by: He Rongguang <herongguang@linux.alibaba.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The is_valid flag should reflect the validity state of both
the XXX_start and XXX_stop functions. But the use of '=' in
XXX_stop overwrites the validity state set by XXX_start. This
commit changes '=' to '|=' in XXX_stop to preserve and combine
the validity state of XXX_start and XXX_stop.
Signed-off-by: wangfushuai <wangfushuai@baidu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
There is a type 'enum operation_mode_e' contains the display modes of
the 'monitor' subcommand. This type isn't used though, instead the
variable 'mode' is of a simple 'int' type.
Change 'mode' variable type from 'int' to 'enum operation_mode_e' in
order to improve compiler type checking.
Built and tested this with different monitor cmdline params. Everything
works as expected, that is nothing changed and no regressions encountered.
Signed-off-by: Roman Storozhenko <romeusmeister@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Update cpupower's P-State frequency calculation and reporting with AMD
Family 1Ah+ processors, when using the acpi-cpufreq driver. This is due
to a change in the PStateDef MSR layout in AMD Family 1Ah+.
Tested on 4th and 5th Gen AMD EPYC system
Signed-off-by: Ananth Narayan <Ananth.Narayan@amd.com>
Signed-off-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
For both the d and e options in 'cpupower idle_set' command, an
atoi() conversion is done without checking if the input argument
is all numeric. So, an atoi conversion is done on any character
provided as input and the CPU idle_set operation continues with
that integer value, which may not be what is intended or entirely
correct.
The output of cpuidle-set before patch is as follows:
[root@xxx cpupower]# cpupower idle-set -e 1$
Idlestate 1 enabled on CPU 0
[snip]
Idlestate 1 enabled on CPU 47
[root@xxx cpupower]# cpupower idle-set -e 11
Idlestate 11 not available on CPU 0
[snip]
Idlestate 11 not available on CPU 47
[root@xxx cpupower]# cpupower idle-set -d 12
Idlestate 12 not available on CPU 0
[snip]
Idlestate 12 not available on CPU 47
[root@xxx cpupower]# cpupower idle-set -d qw
Idlestate 0 disabled on CPU 0
[snip]
Idlestate 0 disabled on CPU 47
This patch adds a check for both d and e options in cpuidle-set.c
to see that the idle_set value is all numeric before doing a
string-to-int conversion using strtol().
The output of cpuidle-set after the patch is as below:
[root@xxx cpupower]# ./cpupower idle-set -e 1$
Bad idle_set value: 1$. Integer expected
[root@xxx cpupower]# ./cpupower idle-set -e 11
Idlestate 11 not available on CPU 0
[snip]
Idlestate 11 not available on CPU 47
[root@xxx cpupower]# ./cpupower idle-set -d 12
Idlestate 12 not available on CPU 0
[snip]
Idlestate 12 not available on CPU 47
[root@xxx cpupower]# ./cpupower idle-set -d qw
Bad idle_set value: qw. Integer expected
Signed-off-by: Brahadambal Srinivasan <latha@linux.vnet.ibm.com>
Signed-off-by: Likhitha Korrapati <likhitha@linux.ibm.com>
Tested-by: Pavithra Prakash <pavrampu@linux.vnet.ibm.com>
Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
If boost sysfs (/sys/devices/system/cpu/cpufreq/boost) file is present
turbo-boost is feature is supported in the hardware. By default this
feature should be enabled. But to disable/enable it write to the sysfs
file. Use the same to control this feature via cpupower.
To enable:
cpupower set --turbo-boost 1
To disable:
cpupower set --turbo-boost 0
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
Tested-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
amd_pstate supports changing of its mode dynamically via `status` sysfs
file. Add the same capability in cpupower. To change the mode to active
mode use below command:
cpupower set --amd-pstate-mode active
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
Tested-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
amd_pstate and intel_pstate active mode drivers support energy
performance preference feature. Through this user can convey it's
energy/performance preference to platform. Add this value change
capability to cpupower.
To change the EPP value use below command:
cpupower set --epp performance
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
Tested-by: Perry Yuan <Perry.Yuan@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
amd-pstate active mode driver name is "amd-pstate-epp". Use common
prefix for string matching condition to recognise amd-pstate active mode
driver.
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Wyes Karny <wyes.karny@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Perry Yuan <Perry.Yuan@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This CPU power monitor shows the power consumption
as exposed by the powercap subsystem, cmp with:
Documentation/power/powercap/powercap.rst
cpupower monitor -m RAPL
| RAPL
CPU| pack | core | unco
0|6853926|967832|442381
8|6853926|967832|442381
1|6853926|967832|442381
9|6853926|967832|442381
Unfortunately RAPL domains cannot be directly mapped to the corresponding
CPU socket/package, core it belongs to.
Not sure this is possible at all with the current data exposed from the
kernel.
Still it can be worthful information for developers trying to optimize
power consumption of workloads or their system in general.
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Zhang Rui <rui.zhang@intel.com>
CC: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Read out powercap zone information via:
cpupower powercap-info
and show the zone hierarchy to the user:
./cpupower powercap-info
Driver: intel-rapl
Powercap domain hierarchy:
Zone: package-0 (enabled)
Power consumption can be monitored in micro Watts
Zone: core (disabled)
Power consumption can be monitored in micro Watts
Zone: uncore (disabled)
Power consumption can be monitored in micro Watts
Zone: dram (disabled)
Power consumption can be monitored in micro Watts
There is a dummy -a option for powercap-info which can/should be used to
show more detailed info later. Like that other args can be added easily
later as well.
A enable/disable option via powercap-set subcommand is also an enhancement
for later.
Also not all RAPL domains are shown. The func walking through RAPL
subdomains is restricted and hardcoded to: "intel-rapl/intel-rapl:0"
On my system above powercap domains map to:
intel-rapl/intel-rapl:0
-> pack (age-0)
intel-rapl/intel-rapl:0/intel-rapl:0:0
-> core
intel-rapl/intel-rapl:0/intel-rapl:0:1
-> uncore
Missing ones on my system are:
intel-rapl-mmio/intel-rapl-mmio:0
-> pack (age-0)
intel-rapl/intel-rapl:1
-> psys
This could get enhanced in:
struct powercap_zone *powercap_init_zones()
and adopted to walk through all intel-rapl zones, but
also to other powercap drivers like dtpm
(Dynamic Thermal Power Management framework),
cmp with: drivers/powercap/dtpm_*
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The default output of cpupower info utils shows unexpected output
when CPU 0 is disabled.
Considering a case where CPU 0 is disabled, output of cpupower idle-info:
Before change:
cpupower idle-info
CPUidle driver: pseries_idle
CPUidle governor: menu
analyzing CPU 0:
*is offline
After change:
./cpupower idle-info
CPUidle driver: pseries_idle
CPUidle governor: menu
analyzing CPU 50:
Number of idle states: 2
Available idle states: snooze CEDE
snooze:
Flags/Description: snooze
Latency: 0
Usage: 101748
Duration: 2724058
CEDE:
Flags/Description: CEDE
Latency: 12
Usage: 270004
Duration: 283019526849
If -c option is not passed, CPU 0 was chosen as the default chosen CPU to
display details. However when CPU 0 is offline, it results in showing
unexpected output. This commit chooses the base_cpu
instead of CPU 0, hence keeping the output more relevant in all cases.
The base_cpu is the number of CPU on which the calling thread is
currently executing.
Signed-off-by: Saket Kumar Bhaskar <skb99@linux.vnet.ibm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add "-c --perf" option in cpupower-frequency-info to get the performance
and frequency values for AMD P-State.
Commit message amended:
Shuah Khan <skhan@linuxfoundation.org>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
AMD P-State kernel module is using the fine grain frequency instead of
acpi hardware pstate. So add a function to print performance and
frequency values.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The print_speed can be as a common function, and expose it into misc
helper header. Then it can be used on other helper files as well.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The legacy ACPI hardware P-States function has 3 P-States on ACPI table,
the CPU frequency only can be switched between the 3 P-States. While the
processor supports the boost state, it will have another boost state
that the frequency can be higher than P0 state, and the state can be
decoded by the function of decode_pstates() and read by
amd_pci_get_num_boost_states().
However, the new AMD P-State function is different than legacy ACPI
hardware P-State on AMD processors. That has a finer grain frequency
range between the highest and lowest frequency. And boost frequency is
actually the frequency which is mapped on highest performance ratio. The
similar previous P0 frequency is mapped on nominal performance ratio.
If the highest performance on the processor is higher than nominal
performance, then we think the current processor supports the boost
state. And it uses amd_pstate_boost_init() to initialize boost for AMD
P-State function.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Introduce the marco definitions and access helper function for
AMD P-State sysfs interfaces such as each performance goals and frequency
levels in amd helper file. They will be used to read the sysfs attribute
from AMD P-State cpufreq driver for cpupower utilities.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
If kernel starts the AMD P-State module, the cpupower will initial the
capability flag as CPUPOWER_CAP_AMD_PSTATE. And once AMD P-State
capability is set, it won't need to set legacy ACPI relative
capabilities anymore.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The processor with AMD P-State function also supports legacy ACPI
hardware P-States feature as well. Once driver sets AMD P-State eanbled,
the processor will respond the finer grain AMD P-State feature instead of
legacy ACPI P-States. So it introduces the cpupower_amd_pstate_enabled()
to check whether the current kernel enables AMD P-State or AMD CPUFreq
module.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add AMD P-State capability flag in cpupower to indicate AMD new P-State
kernel module support on Ryzen processors.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Remove the family check for accessing the MSR_AMD_HWCR MSR and replace
it with a cpupower cap flag.
This update also allows for the removal of the local cpupower_cpu_info
variable in cpufreq_has_boost_support() since we no longer need it to
check the family.
Signed-off-by: Nathan Fontenot <nathan.fontenot@amd.com>
Reviewed-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The decode_pstates() routine no longer uses the CPU family and
the caleed routines (get_cof() and get_did()) can grab the family
from the global cpupower_cpu_info struct. These update removes
passing the family arg to all these routines.
Signed-off-by: Nathan Fontenot <nathan.fontenot@amd.com>
Reviewed-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The enabled bit (bit 63) is common for all families so we can remove
the multiple enabled checks based on family and have a common check
for HW pstate enabled.
Signed-off-by: Nathan Fontenot <nathan.fontenot@amd.com>
Reviewed-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The family checks in get_cof() and get_did() need to use the
correct MSR format depending on the family. Add a cpupower
capability for using the pstatedef (family 17h and newer) to
control this instead of direct family checks.
Signed-off-by: Nathan Fontenot <nathan.fontenot@amd.com>
Reviewed-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The pscur variable is set but not uused, just remove it.
This may have previsously been set to validate the MSR_AMD_PSTATE_STATUS
MSR. With the addition of the CPUPOWER_CAP_AMD_HW_PSTATE cap flag this
is no longer needed since the cpuid bit to enable this cap flag also
validates that the MSR_AMD_PSTATE_STATUS MSR is present.
Signed-off-by: Nathan Fontenot <nathan.fontenot@amd.com>
Reviewed-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add a check in get_cpu_info() for the ability to read frequencies
from hardware and set the CPUPOWER_CAP_AMD_HW_PSTATE cpuid flag.
The cpuid flag is set when CPUID_80000007_EDX[7] is set,
which is all families >= 10h. The check excludes family 14h
because HW pstate reporting was not implemented on family 14h.
This is intended to reduce family checks in the main code paths.
Signed-off-by: Nathan Fontenot <nathan.fontenot@amd.com>
Reviewed-by: Robert Richter <rrichter@amd.com>
Reviewed-by: skhan@linuxfoundation.org
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The name is Core Performance Boost (CPB) for the cpuid flag. Correct
cpuid caps flag to use this name (instead of CBP).
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Nathan Fontenot <nathan.fontenot@amd.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The msr_pstate union struct named fam17h_bits is misleading since
this is the struct to use for all families >= 0x17, not just
for family 0x17. Rename the bits structs to be 'pstate' (for pre
family 17h CPUs) and 'pstatedef' (for CPUs since fam 17h) to align
closer with PPR/BDKG (1) naming.
There are no functional changes as part of this update.
1: AMD Processor Programming Reference (PPR) and BIOS and
Kernel Developer's Guide (BKDG) available at:
http://developer.amd.com/resources/developer-guides-manuals
Signed-off-by: Nathan Fontenot <nathan.fontenot@amd.com>
Reviewed-by: Robert Richter <rrichter@amd.com>
Reviewed-by: skhan@linuxfoundation.org
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from
the frequency table as the current frequency and clean up that
driver (Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle
driver (Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables
in DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it
to take the interconnect and OPP information from DT and clean it
up ((Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print
driver flags for devices with debug enabled (Alex Shi, Patrice
Chotard, Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan).
-----BEGIN PGP SIGNATURE-----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=BVdX
-----END PGP SIGNATURE-----
Merge tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
... instead of poking at the MSR. For that, move the accessor functions
to misc.c and add a sysfs-writing function too.
There should be no functional changes resulting from this.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: Thomas Renninger <trenn@suse.com>
Link: https://lkml.kernel.org/r/20201029190259.3476-2-bp@alien8.de
When a user tries to modify cpuidle or cpufreq properties on offline
CPUs, the tool returns success (exit status 0) but also does not provide
any warning message regarding offline cpus that may have been specified
but left unchanged. In case of all or a few CPUs being offline, it can be
difficult to keep track of which CPUs didn't get the new frequency or idle
state set. Silent failures are difficult to keep track of when there are a
huge number of CPUs on which the action is performed.
This patch adds helper functions to find both online and offline CPUs and
print them out accordingly.
We use these helper functions in cpuidle-set and cpufreq-set to print an
additional message if the user attempts to modify offline cpus.
Reported-by: Pavithra R. Prakash <pavrampu@in.ibm.com>
Signed-off-by: Brahadambal Srinivasan <latha@linux.vnet.ibm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Building cpupower with -fno-common in CFLAGS results in errors due to
multiple definitions of the 'cpu_count' and 'start_time' variables.
./utils/idle_monitor/snb_idle.o:./utils/idle_monitor/cpupower-monitor.h:28:
multiple definition of `cpu_count';
./utils/idle_monitor/nhm_idle.o:./utils/idle_monitor/cpupower-monitor.h:28:
first defined here
...
./utils/idle_monitor/cpuidle_sysfs.o:./utils/idle_monitor/cpuidle_sysfs.c:22:
multiple definition of `start_time';
./utils/idle_monitor/amd_fam14h_idle.o:./utils/idle_monitor/amd_fam14h_idle.c:85:
first defined here
The -fno-common option will be enabled by default in GCC 10.
Bug: https://bugs.gentoo.org/707462
Signed-off-by: Mike Gilbert <floppym@gentoo.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
