The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Current Kconfig menu at [ALSA for SoC audio support] has no rules.
So, some venders are using menu style, some venders are listed each drivers
on top page, etc. It is difficult to find target vender and/or drivers
because it is very random.
Let's standardize ASoC menu
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/874iwl20th.wl-kuninori.morimoto.gx@renesas.com
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The removed dai_link->platform component cause a fail which
is exposed at runtime. (ex: when a sound tool is used)
This patch re-adds the dai_link->platform component to have
a full card registered.
Before this patch:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 1: HDMI [HDMI], device 0: HDMI snd-soc-dummy-dai-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
$ speaker-test -D plughw:1,0 -t sine
speaker-test 1.2.8
Playback device is plughw:1,0
Stream parameters are 48000Hz, S16_LE, 1 channels
Sine wave rate is 440.0000Hz
Playback open error: -22,Invalid argument
After this patch which restores the platform component:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: HDMI [HDMI], device 0: HDMI snd-soc-dummy-dai-0 [HDMI snd-soc-dummy-dai-0]
Subdevices: 0/1
Subdevice #0: subdevice #0
-> Resolve the playback error.
Fixes: 3b0db249cf ("ASoC: ti: remove unnecessary dai_link->platform")
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
Link: https://patch.msgid.link/20250531141341.81164-1-wf.yn386@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250408-gpiochip-set-rv-sound-v1-2-dd54b6ca1ef9@linaro.org
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is a very big release due to a combination of some big new work,
mainly new drivers and generic SoundWire support, and some wide ranging
cleanup work that made small changes to a lot of drivers.
- Morimoto-san has completed the conversion to use modern terminology
for the clocking configuration, and several other cleanups with
narrower impact.
- All the power management operation configuration was updated to use
current idioms by Takashi Iwai.
- Clarification of the control operations from Charles Keepax.
- Prepartory work for more generic SoundWire SCDA controls from Charles
Keepax.
- Support for AMD ACP 7.x, AWINC WM88166, Everest ES8388, Intel AVS
PEAKVOL and GAIN DSP modules Mediatek MT8188 DMIC, NXP i.MX95, nVidia
Tegra interconnects, Rockchip RK3588 S/PDIF, Texas Instruments
SN012776 and TAS5770L, and Wolfson WM8904 DMICs,
Some changes from the tip tree adding APIs needed by the AMD code are
included, these were unfortunately rebased in the tip tree after being
pulled in. There's also some regmap changes supporting the SCDA work
and some devres refactoring that was pulled in to support other changes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmfhZEUACgkQJNaLcl1U
h9DQjgf9FxqmX7qAbT3tV06lX6UJ79KtCGquvVpToxP3nMFa05h/HSJlQAnqEFkL
AUdAr/bfH6noDIqL08j+DMHs85lz6fP06PubCmQCHEk+yAEPOZ19OUsTKbhdXcG2
GTObvLEjnz8MDnUW99SwoB52y3DX/7F09uhcbv+xiLIZo0EmQOcTsLKx79XwuzgU
q52mQBXYi7CDhVTlnITeapcLj7G+6r2m7zLsQRWa897bKp/nRVq08GhWu0SHBNtP
m/RwBvwPZEgCDxH+aHOWvc6S7yQpotC9EIvTUchxFGkcHh9OKoLUoWLH7p+d99B2
ydVWgOz72GwRhAjp9FHH7X49A5UMmg==
=xZD3
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.15' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.15
This is a very big release due to a combination of some big new work,
mainly new drivers and generic SoundWire support, and some wide ranging
cleanup work that made small changes to a lot of drivers.
- Morimoto-san has completed the conversion to use modern terminology
for the clocking configuration, and several other cleanups with
narrower impact.
- All the power management operation configuration was updated to use
current idioms by Takashi Iwai.
- Clarification of the control operations from Charles Keepax.
- Prepartory work for more generic SoundWire SCDA controls from Charles
Keepax.
- Support for AMD ACP 7.x, AWINC WM88166, Everest ES8388, Intel AVS
PEAKVOL and GAIN DSP modules Mediatek MT8188 DMIC, NXP i.MX95, nVidia
Tegra interconnects, Rockchip RK3588 S/PDIF, Texas Instruments
SN012776 and TAS5770L, and Wolfson WM8904 DMICs,
Some changes from the tip tree adding APIs needed by the AMD code are
included, these were unfortunately rebased in the tip tree after being
pulled in. There's also some regmap changes supporting the SCDA work
and some devres refactoring that was pulled in to support other changes.
For 'ti,j7200-cpb-audio' compatible, there is support for only one PLL for
48k. For 11025, 22050, 44100 and 88200 sampling rates, due to absence of
J721E_CLK_PARENT_44100, we get EINVAL while running any audio application.
Add support for these rates by using the 48k parent clock and adjusting
the clock for these rates later in j721e_configure_refclk.
Fixes: 6748d05590 ("ASoC: ti: Add custom machine driver for j721e EVM (CPB and IVI)")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://patch.msgid.link/20250318113524.57100-1-j-choudhary@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_disable_unprepare() already checks NULL by using IS_ERR_OR_NULL.
Remove unneeded NULL check for dev->ext_clk here.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://patch.msgid.link/20250312033509.1235268-1-nichen@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Because card->dev = &pdev->dev is already defined in the rx51_soc_probe
function, and then &pdev->dev is still used.
Signed-off-by: Liu Jing <liujing@cmss.chinamobile.com>
Link: https://patch.msgid.link/20241015074938.6247-1-liujing@cmss.chinamobile.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all drivers below sound/soc to use .remove(), with the eventual
goal to drop struct platform_driver::remove_new(). As .remove() and
.remove_new() have the same prototypes, conversion is done by just
changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20240909151230.909818-2-u.kleine-koenig@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Jai Luthra <j-luthra@ti.com>:
This series fixes two patches:
1. Fix the dmaengine API usage by calling dmaengine_synchronize() after
dmaengine_terminate_async() when xrun events occur in application
2. Use the McASP AFIFO property from DT to refine the period size,
instead of hardcoding minimum to 64 samples
Set driver name to "HDMI". This simplifies the code and gets rid of
the following error messages:
ASoC: driver name too long 'HDMI 58040000.encoder' -> 'HDMI_58040000_e'
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20240610125847.773394-1-primoz.fiser@norik.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The minimum period size was enforced to 64 as older devices integrating
McASP with EDMA used an internal FIFO of 64 samples.
With UDMA based platforms this internal McASP FIFO is optional, as the
DMA engine internally does some buffering which is already accounted for
when registering the platform. So we should read the actual FIFO
configuration (txnumevt/rxnumevt) instead of hardcoding frames.min to
64.
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240611-asoc_next-v3-2-fcfd84b12164@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-31-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
When using davinci-mcasp as CPU DAI with simple-card, there are some
conditions that cause simple-card to finish registering a sound card before
davinci-mcasp finishes registering all sound components. This creates a
non-working sound card from userspace with no problem indication apart
from not being able to play/record audio on a PCM stream. The issue
arises during simultaneous probe execution of both drivers. Specifically,
the simple-card driver, awaiting a CPU DAI, proceeds as soon as
davinci-mcasp registers its DAI. However, this process can lead to the
client mutex lock (client_mutex in soc-core.c) being held or davinci-mcasp
being preempted before PCM DMA registration on davinci-mcasp finishes.
This situation occurs when the probes of both drivers run concurrently.
Below is the code path for this condition. To solve the issue, defer
davinci-mcasp CPU DAI registration to the last step in the audio part of
it. This way, simple-card CPU DAI parsing will be deferred until all
audio components are registered.
Fail Code Path:
simple-card.c: probe starts
simple-card.c: simple_dai_link_of: simple_parse_node(..,cpu,..) returns EPROBE_DEFER, no CPU DAI yet
davinci-mcasp.c: probe starts
davinci-mcasp.c: devm_snd_soc_register_component() register CPU DAI
simple-card.c: probes again, finish CPU DAI parsing and call devm_snd_soc_register_card()
simple-card.c: finish probe
davinci-mcasp.c: *dma_pcm_platform_register() register PCM DMA
davinci-mcasp.c: probe finish
Cc: stable@vger.kernel.org
Fixes: 9fbd58cf4a ("ASoC: davinci-mcasp: Choose PCM driver based on configured DMA controller")
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240417184138.1104774-1-jpaulo.silvagoncalves@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
McBSP's data delay can be configured from 0 to 2 bit clock periods. 0 is
used for DSP_B format, 1 is used for DSP_A format, 2 is unused.
A data delay of 2 bit clock periods can be used to interface to
'T1 framing' devices where data stream is preceded by a 'framing bit'. On
transmission, McBSP inserts a blank period (high-impedance period)
before the first data bit to leave an opportunity for other devices to
set this 'framing bit'. On reception, McBSP discards the 'framing bit'
that precedes the data stream.
Add support for the 'framing bit' according to the
'ti,T1-framing-[tx/rx]' device-tree properties. If a flag is present,
the data delay is set to 2 bit clock periods regardless of the selected
DAI format.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-14-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
S24_LE is supported by McBSP but not by the driver.
Add S24_LE to driver's supported formats. Using it enables the sign
extension in DRR (Data Receive Register). The other formats are kept
with the zero extension in DRR.
Remove data_type table as it is no longer used.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-12-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
McBSP has free-running mode where serial clocks continue to run during
emulation halts. This mode is always enabled by the driver.
Set free-running mode when SND_SOC_DAIFMT_CONT is selected by DAI
format, unset it when SND_SOC_DAIFMT_GATED is selected.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-11-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
McBSP can generate a SYNCERR when unexpected frame pulses are
detected. The driver always disables this feature and ignore the
unexpected frame pulses.
Enable the generation of SYNCERR by the McBSP. Unexpected frame
pulses are not ignored anymore.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-10-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
McBSP is able to drive bit clock and consume frame clock but BP_FC
format is not handled by McBSP driver.
Add BP_FC format support.
When BP_FC is selected:
- CLKX and CLKR are configured as outputs
- The sample rate generator is configured to be able to provide bit
clock.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-9-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM is not supported by the McBSP driver. The McBSP datasheet does not
name explicitly TDM as a supported format but it is possible to configure
the McBSP to do TDM if all slots are used by McBSP.
Add TDM support. It uses single-phase frame. Slot width is used to
compute the McBSP's word length.
Implement the set_tdm_slot() hook of snd_soc_dai_ops struct. It only
supports TDM if all slots are used by McBSP.
The snd_soc_dai_driver's channels_max is updated from 2 to 128.
This was tested with BP_FC format on a platform designed off of
DAVINCI/OMAP_L138. A check is done in davinci_i2s_set_dai_fmt() to
prevent TDM to be used with BC_FC and BC_FP formats.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-8-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In davinci_i2s_hw_params(), mcbsp_word_length is set twice to
asp_word_length[fmt].
Remove second unnecessary assignment.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-7-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
McBSP's internal sample rate generator can be programed to be driven by
its internal clock or by an external clock source located on CLKS pin.
The external clock source case is not handled by the driver.
Handle an optional clock related to this external clock source. If
present, the driver uses the clock located on CLKS pin as input for the
sample rate generator. Thus, the external clock rate is used to compute
divisors. If this optional clock is not present, the sample rate
generator is driven by the McBSP's functional clock.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-6-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In probe(), the dev_err() is used for every returned error.
Replace dev_err() with dev_err_probe() where -EPROBE_DEFER can be
returned.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-5-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The clk_input_pin attribute of davinci_mcbsp_dev struct is not set since
commit 257ade78b6 ("ASoC: davinci-i2s: Convert to use edma-pcm").
Remove the attribute.
Keep the behaviour of the MCBSP_CLKR case as MCBSP_CLKR == 0.
I can't test the BC_FP format so I added back the initial comment that
was removed by commit ec63755337 ("ASoC: DaVinci: Added selection of
clk input pin for McBSP"). This was the last dependency to
linux/platform_data/davinci_asp.h so it is not included anymore.
Remove the enum mcbsp_clk_input_pin from davinci_asp.h as it is not used
anywhere else.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-4-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Let's use devm_snd_soc_register_card() instead of snd_soc_register_card()
and ignore snd_soc_unregister_card()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://msgid.link/r/87zfxcwv58.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to check for an active device as otherwise we get warnings
for some mcbsp instances for "Runtime PM usage count underflow!".
Reported-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231030052340.13415-1-tony@atomide.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is now built only when MACH_AMS_DELTA is selected, which
requires a very specific selection of ARCH settings. As a consequence, it
gets very little attention from build-bots, if not none.
Drop the driver dependency on <asm/mach-types.h>, no longer required since
conversion to snd_soc_register_card() and drop of machine_is_ams_delta().
With that in place, allow the driver to be built in any environment as
long as COMPILE_TEST is selected. Take care of not selecting
SND_SOC_OMAP_MCBSP if COMMON_CLK is not selected.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Link: https://lore.kernel.org/r/20231008135601.542356-1-jmkrzyszt@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231006-dt-asoc-header-cleanups-v3-5-13a4f0f7fee6@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev> # for at91
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231006-dt-asoc-header-cleanups-v3-1-13a4f0f7fee6@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver includes the legacy header <linux/gpio.h> but doesn't
use it. Drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Link: https://lore.kernel.org/r/20230926-descriptors-asoc-ti-v1-5-60cf4f8adbc5@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The Pandora uses GPIO descriptors pretty much exclusively, but not
for ASoC, so let's fix it. Register the pins in a descriptor table
in the machine since the ASoC device is not using device tree.
Use static locals for the GPIO descriptors because I'm not able
to experient with better state storage on any real hardware. Others
using the Pandora can come afterwards and improve this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Link: https://lore.kernel.org/r/20230926-descriptors-asoc-ti-v1-4-60cf4f8adbc5@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The TWL4030 is actually only ever populated from the device tree,
so we can just pass the right device and headphone jack GPIO name
to snd_soc_jack_add_gpios() and it will pick the right GPIO right
from the device tree.
The platform data patch is unused (no in-tree users of the pdata
method) but these can use GPIO descriptor tables rather than global
GPIO numbers if they need this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Link: https://lore.kernel.org/r/20230926-descriptors-asoc-ti-v1-3-60cf4f8adbc5@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
