Many of the DisCo properties that specify Control values have an
additional variant that specifies a separate value for each Control
Number. Add support for these.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250718135432.1048566-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current regmap readable/writeable helper functions always
allow the Next flag and allows any Control Number. Mask the Next
flag based on SDCA_ACCESS_MODE_DUAL which is the only Mode that
supports it. Also check that the Control Number is valid for
the given control.
Fixes: e3f7caf74b ("ASoC: SDCA: Add generic regmap SDCA helpers")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250718135432.1048566-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to include MODULE_LICENSE() and MODULE_DESCRIPTION() in
sdca_regmap.c as this file is part of a larger module that already
defines these.
Fixes: e3f7caf74b ("ASoC: SDCA: Add generic regmap SDCA helpers")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Link: https://patch.msgid.link/20250516131011.221310-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The concept of an SDCA default value differs slightly from the regmap
usage of the term. An SDCA default is a value that is parsed from DisCo
and then written out to the hardware if no user value has superceded
it. Add a helper function that will iterate through all the SDCA
Controls and write out any default values. After these have been written
out once they will exist in the cache and that will take care of any
user values superceeding them. The code here also writes out any
Controls with a fixed value as there is only one available value for
these Controls there is no point in allowing the user to select them,
simply treat them similarly to a default.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Link: https://patch.msgid.link/20250217140159.2288784-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helpers to parse the DisCo Constant values from ACPI and populate an
array of reg_defaults with these. This will allow drivers to access
these ACPI specified values through the same interface as other
registers that are physically present on the device, using the regmap
cache.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Link: https://patch.msgid.link/20250217140159.2288784-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper functions that SDCA drivers can use to calculate the
properties of SDCA Controls (registers) specified through DisCo.
Most of these are fairly obvious from the SDCA Access Modes.
DisCo Constants, values which are specified in the ACPI rather than on
the device, are handled as unreadable and unwritable registers. The
intention is these will be populated in the register defaults table
allowing drivers to read them normally. This means the drivers can be
agnostic as to which values are DisCo Constants.
Finally, support for SDCA Dual Ranked Controls is currently limited
here, at the moment the current value will be used directly. Writing
the current value directly is valid as per the specification
although the synchronicity of updates across multiple registers is
lost. Support for this will probably need to be added later. But its a
fairly hard problem and doesn't need to be solved immediately.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Link: https://patch.msgid.link/20250217140159.2288784-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
