This patch adds support of the ROHM BD28623MUV
Class D speaker amplifier for Flat-panel TVs.
This IC delivers an output power of 20W + 20W.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max9759 is a gpio controlled amplifier.
Tested on a Variscite Dart MX6 SoM based custom board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AK5558 is a 32-bit, 768 kHZ sampling, differential input ADC
for digital audio systems.
Datasheet is available at:
https://www.akm.com/akm/en/file/datasheet/AK5558VN.pdf
Initial patch includes support for normal and TDM modes.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Junichi Wakasugi <wakasugi.jb@om.asahi-kasei.co.jp>
[initial coding for 3.18 kernel]
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
[cleanups and porting to 4.9 kernel]
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
[tdm support]
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
[pm support, cleanups and porting to latest kernel]
Signed-off-by: Mark Brown <broonie@kernel.org>
The AK4458 is a 32-bit 8ch Premium DAC that corresponds
to a 768kHz PCM input and an 11.2MHz DSD input at maximum.
It supports I2S, DSD and TDM modes with 24 or 32 bit MSB
or 16, 24, 32 LSB formats. Its datasheet is available here:
https://www.akm.com/akm/en/file/datasheet/AK4458VN.pdf
Signed-off-by: Junichi Wakasugi <wakasugi.jb@om.asahi-kasei.co.jp>
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Cosmin-Gabriel Samoila <cosmin.samoila@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All sn95031 stuff was removed in commit 987da3fe17 ("ASoC: sn95031: remove this code")
Since SND_SOC_SN95031 was gone, remove makefile about it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This codec was used in MFLD systems in the PMIC chip, we no longer have
users for this, so remove it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently there is no support for TSCS42xx audio CODECs.
Add support for TSCS42xx audio CODECs.
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Steven Eckhoff <steven.eckhoff.opensource@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is an initial version of the PCM186x codec driver supporting both
2-channel and 4-channel device variants. Not all device features are
supported yet such as master/slave mode PLL configuration for which the
codec driver currently relies on the PCM186x built-in clock
auto-detection feature or the connection of digital microphones.
However here is what's here and what should work:
- Support for SPI and I2C low-level interfaces
- Regmap support and basic register definitions
- Input Mixer and Mux selection
- I2C, LJ, and TDM DAI format support
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Texas Instruments TAS6424 device is a high-efficiency quad-channel
Class-D audio power amplifier. Its digital time division multiplexed
(TDM) interface enables up to 2 devices to share the same bus,
supporting a total of eight channels from one audio serial port.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The main rt5514 driver optionally calls into the SPI back-end to load
the firmware. This causes a link error when one driver selects rt5514
as built-in and another driver selects rt5514-spi as a loadable module:
sound/soc/codecs/rt5514.o: In function `rt5514_dsp_voice_wake_up_put':
rt5514.c:(.text+0xac8): undefined reference to `rt5514_spi_burst_write'
As a workaround, this adds another silent symbol, to force rt5514-spi
to be built-in for that configuration. I'm not overly happy with
that solution, but couldn't come up with anything better. Using
'IS_REACHABLE()' would break the case that relies on the loadable
module, and all other ideas would result in more complexity.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is still using old driver style, this patch also
fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is still using old driver style, this patch also
fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is still using old driver style, this patch also
fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Cirrus Logic CS43130 codec.
Support:
I2S/DSP PCM playback.
DoP/DSD playback.
HP detection and DC/AC impedance measurement.
Signed-off-by: Li Xu <li.xu@cirrus.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
WM8524 is a 24-bit 192KHz stereo digital/analog converter (DAC) with
integral charge pump and a simple hardware control interface.
Product information can be found at:
https://www.cirrus.com/products/wm8524/
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT274 is a HD-A/SOC dual mode codec. This is the initial codec driver
of SOC mode.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It adds ASoC driver for AUD96P22 stereo audio codec integrated on ZTE
ZX family SoCs. The driver includes the support for a number of volume
and mute controls, and power bits for various playback and recording
components.
Due to that the board for testing only supports playback, recording
support is untested.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a codec driver for the Everest ES8316, based on code provided by
David Yang from Everest Semi.
I limited the functionality to items where the vendor code was clear,
and things that can be tested on the Weibu F3C (Intel Cherry Trail).
As a result the initial implementation only supports running in slave
mode at single speed (up to 48kHz sample rate) using I2S. HPD is not
supported.
Signed-off-by: David Yang <yangxiaohua@everest-semi.com>
[drake@endlessm.com: significant cleanups and simplifications,
remove dead/unclear code]
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for NAU88L24.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dio2125 is a stereo output driver with adjustable gain.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Cirrus Logic
CS35L35 9V Boosted Amplifier
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The es7134 is 24bit, 192Khz i2s DA converter for PCM audio.
Datasheet is available here : http://www.everest-semi.com/pdf/ES7134LV%20DS.pdf
This driver is also compatible with the es7144, which is the same as the
es7134, with 2 additional pins for filtering capacitors.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Cirrus Logic CS42L42 codec. SoundWire support
is not enabled. Features support for I2C control and I2S audio.
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts(Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Digital part of the Codec which is integrated
into Application Processor.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts (Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Analog part of the Codec which is integrated
into PMIC PM8916.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit of the Cirrus Logic cs35l34 8V boosted class D
amplifier.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the initial codec driver for both rt5663 rt5668 codec.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is for codec NAU88C10 of Nuvoton Technology Corporation.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds driver for the MAX98504 speaker amplifier. The MAX98504
is a high efficiency mono class D amplifier that features an integrated
boost converter with voltage and current sensing ADCs for Dynamic Speaker
Management.
This driver does not include support for the I2S DAI, as we wouldn't be
able to test such code in a hardware configuration where the amplifier
has only wired the analogue input.
Signed-off-by: Inha Song <ideal.song@samsung.com>
[k.kozlowski: rebased on 4.1]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[s.nawrocki: removed unused macro definitions, rewrote regulator supply
related parts, rewrote regmap configuration code, added support for speaker
enable and global chip enable through DAPM, rewritten as component driver,
added PDM DAI definition and TDM callbacks for PDM channels configuration]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
--
Changes since v2:
- added parsing of the VBAT brownout DT properties,
- removed MAX98504_REG_SPEAKER_SOURCE_SELECT register initialization,
- removed unused macro definitions.
Changes since v1:
- none.
Changes since initial version:
- added regulator supply handling,
- added DAPM widges for speaker source selection,
- added PDM DAI definition and TDM callbacks for setting up active
PDM Tx channels and I/V sense ADC data mapping,
- removed all optional DT properties, added regulator supply properties
in the DT binding.
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit of the Cirrus Logic cs35l33 8V boosted class D
amplifier.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Multiple devices from the ADAU family share the same PLL structure and
configuration register layout. Introduce a new helper module that can be
used to calculated the PLL configuration registers based on a specified
input frequency and the desired output frequency of the PLL.
The ADAU1761/ADAU1781 and ADAU1373 drivers are updated to make use of this
new helper module. But future drivers for additional devices from the ADAU
family are also expected to make use of it.
In anticipation of sharing more infrastructure code between different
devices from the ADAU family the new module is called adau-utils.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The device has multiple control interfaces, I2C and SPI. The I2C interface
mainly controls the register settings of codec. The SPI interface is in
order to provide the high speed transmission of data. For example, high
bandwidth memory read/write of DSP. The patch adds the rt5514 SPI driver
for loading the firmware of DSP and retrieving the voice data from DSP
after the system is waked up by specific voice.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the ADAU7002 PDM-to-I2S/TDM converter. The
ADAU7002 takes a stereo PDM signal (e.g. from two digital microphones) and
converts it into a I2S/TDM PCM stream. The chip does not have a
programmable control interface and the driver simply describes the static
capabilities of the chip.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a driver for the MAX9860 Mono Audio Voice Codec.
https://datasheets.maximintegrated.com/en/ds/MAX9860.pdf
This driver does not support sidetone since the DVST register field is
backwards with the mute near the maximum level instead of the minimum.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
CS53L30 is a Quad-Channel ADC from Cirrus Logic with an I2S/TDM DAI.
So this patch adds a codec driver for CS53L30 that includes 4-channel
24-bit recording and TDM mode supports.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some definitions to support the PCM5102A codec
by Texas Instruments.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Changes to original patch by Florian Meier:
* rebased (Makefile and Kconfig
* fixed checkpath errors (spaces, newlines)
* added dt-binding documentation
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Texas Instruments TAS5720L/M device is a high-efficiency mono
Class-D audio power amplifier optimized for high transient power
capability to use the dynamic power headroom of small loudspeakers.
Its digital time division multiplexed (TDM) interface enables up to
16 devices to share the same bus.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for running the tlv32x4 control channel over SPI rather than I2C.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
To prepare for abstracting adding SPI support, the I2C pieces needs to
be in its own moudle. This patch moves common probe code into aic32x4_probe
and common removal code into aic32x4_remove. It also creates a static
regmap config structure to be copied in the I2C specific driver.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hdmi-codec is a platform device driver to be registered from
drivers of external HDMI encoders with I2S and/or spdif interface. The
driver in turn registers an ASoC codec for the HDMI encoder's audio
functionality.
The structures and definitions in the API header are mostly redundant
copies of similar structures in ASoC headers. This is on purpose to
avoid direct dependencies to ASoC structures in video side driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the initial codec driver for rt5514. The codec includes a low power
DSP for voice wake up. The register address is incremental by 4 in the DSP
memory map. In order to recover the codec settings in the codec mode and
manipulate the DSP mode for voice wake up, we use the multi-level register
map. One is for ALSA API in codec mode that can be recovered by cache
before recording. Another is for DSP related settings that can be accessed
with 32bit address of the DSP in the application of voice wake up.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PCM179x family supports both SPI and I2C. This patch adds support
for the I2C interface.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pcm179x family supports both SPI and I2C for configuration. This
patch splits the driver into core and SPI parts, in preparation for
I2C support.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pcm1792a is compatible with pcm1795 and pcm1796 so it's
better to have them under the common name pcm179x
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for Texas Instruments pcm3168a codec
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for DA7217 and DA7218 audio codecs.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RK3036 SoC integrated with an Inno audio codec.
This driver implements the functions of it.
There is not need a special machine driver, since the
simple-card machine driver works perfect in this case.
Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds HDA based HDMI driver to be used in platforms like SKL
and onwards
Register the hdmi driver with hda bus and register dais.
Also parse the widget and initialize identified pin and converter
widgets.
For simplification, currently only one pin and one converter
widget are enabled on board, as well as limit the rates supported
to simples ones and not based on ELD. This things will come
eventually once basic support for this is merged
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Cirrus Logic CS47L24 and WM1831 codecs.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for the DA7219 audio codec with built-in advanced
accessory detect features.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hdmi stub codec has not been used since refactoring of OMAP HDMI
audio support.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the InvenSense ICS-43432 I2S MEMS microphone.
This is a non-software-configurable MEMS microphone with I2S output.
Tested on a setup with a single ICS-43432 (the device itself supports
stereo operation using a hardware pin controlling left vs. right channel
output).
Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Codec part of the sti platform that supports codec IPs.
This first version does not support HDMI, but only DAC and SPDIF out.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver add PCM interface to a GTM601 UMTS modem chip.
There is no configuration interface.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch separates the IO function from the rt286. It is prepared to share
for new chips that support the same IO function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce a new codec driver for the Texas Instruments
TAS5711/TAS5717/TAS5719 power amplifier chips. These chips are typically
used to take an I2S digital audio input and drive 10-20W into a pair of
speakers.
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify dependencies by using new style split out bus interfaces.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add codec driver for the Maxim MAX98357A DAC.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Acked-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TS3A227E is an autonomous audio accessory detection and
configuration switch that detects 3-pole or 4-pole audio accessories
and configures internal switches to route the signals accordingly.
This chip also has built-in support for the new button standard
described in the Android "Wired audio headset specification" v1.0.
These buttons will be reported on the jack as buttons 0-3 mapped to
KEY_MEDIA, KEY_VOLUMEUP, KEY_VOLUMEDOWN, and KEY_VOICE_COMMAND.
This will be added as an aux_dev and have the jack passed in from the
machine driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Create a separate module for rt5677 spi driver. Without
this patch, the build fails due to multiple defs of
'init_module' and 'cleanup_module'. module_spi_driver()
defines its own module, so it can't be part of the rt5677
module.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALC5677 has a programmable DSP, and there is a SPI that is dadicated for DSP
firmware loading. Therefore, the patch includes a SPI driver for writing the DSP
firmware. The VAD(Voice Activaty Detection) has be implemented and use the DSP to
recognize the key phase.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the cs4271 driver depends on SND_SOC_I2C_AND_SPI.
So the driver cannot be built as built-in if CONFIG_I2C=m.
Split SPI and I2C code into different modules to avoid this issue.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Analog Devices SSM4567 is a boost class-D audio amplifier.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a codec driver for the Everest ES8328. It supports two separate audio
outputs and two separate audio inputs.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Cirrus Logic CS35L32 Boosted Amplifier
I2S output provides monitor data to the SOC/CODEC/DSP for speaker protection/enhancement algorithms
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Support the TI TAS2552 Class D amplifier.
The TAS2552 is a high efficiency Class-D audio
power amplifier with advanced battery current
management and an integrated Class-G boost
The device constantly measures the
current and voltage across the load and provides a
digital stream of this information.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds Realtek ALC286 codec driver.
ALC286 is a dual mode codec, which can run as HD-A or I2S mode.
It is controlled by HD-A verb commands via I2C protocol.
The following is the I/O difference between ALC286 and general I2S codecs.
1. A HD-A verb command contains three parts, NID, VID, and PID.
And an I2S command contains only two parts: address and data.
2. Not only the register address is written, but the read command also
includes the entire write command.
3. rt286 uses different registers for read and write the same bits.
We map verb command to regmap structure. However, we read most registers from
cache to prevent the asymmetry read/write issue in rt286.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Gustaw Lewandowski <gustaw.lewandowski@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a minimum support of Realtek ALC5670 codec.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Cirrus Logic CS4265 Stereo I2C CODEC.
Signed-off-by: Paul Handrigan <paul.handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the SigmaDSP module is built-in, but the I2C core is build as a module
we'll get a undefined reference:
sound/built-in.o: In function `sigma_action_write_i2c':
:(.text+0x5d8d4): undefined reference to `i2c_master_send'
This can happen if a audio driver that is using the regmap SigmaDSP interface is
built into the kernel, but core I2C support is build as a module. To fix this
split the SigmaDSP module into three modules, one module providing the core
infrastructure and two small modules implementing the regmap and I2C interfaces.
This allows e.g. the core infrastructure and regmap support to be built into the
kernel while I2C support can still be build as a module.
Fixes: dab464b60 ("ASoC: Add ADAU1361/ADAU1761 audio CODEC support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the SigmaDSP module is built-in, but the I2C core is build as a module
we'll get a undefined reference:
sound/built-in.o: In function `sigma_action_write_i2c':
:(.text+0x5d8d4): undefined reference to `i2c_master_send'
This can happen if a audio driver that is using the regmap SigmaDSP interface is
built into the kernel, but core I2C support is build as a module. To fix this
split the SigmaDSP module into three modules, one module providing the core
infrastructure and two small modules implementing the regmap and I2C interfaces.
This allows e.g. the core infrastructure and regmap support to be built into the
kernel while I2C support can still be build as a module.
Fixes: dab464b60 ("ASoC: Add ADAU1361/ADAU1761 audio CODEC support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch adds the RL6231 class device shared support for RT5640, RT5645 and
RT5651. The function of the DMIC clock calculation can be shared by RL6231
shared support.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Analog Devices ADAU1381 and ADAU1781 audio
CODECs. The device is a low-power, 24-bit stereo audio CODEC with multiple
analog inputs and outputs, two digital microphone inputs and an I2S interface.
The device can be controlled either using I2C or SPI. The main difference
between the two variants is that the ADAU1781 has a freely programmable SigmaDSP
processor, while the ADAU1381 has a fixed function wind noise reduction filter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Analog Devices ADAU1361 and ADAU1761 CODECs.
The device is a a low-power, 24-bit stereo audio CODEC with multiple analog
input and outputs, one digital microphone input and an I2S interface. The device
can be controlled either via I2C or SPI. The main difference between the two
variants is that the ADAU1761 has a built-in SigmaDSP, while the ADAU1361 has
not.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADAU1X61 and ADAU1X81 are very similar in the digital domain, but are quite
different in the analog domain. This patch adds support for the common parts of
the ADAU1X61 and ADAU1X81 CODECs.
The patch also restores some of the alphabetical order in the Makfile and
Kconfig.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Cirrus Logic Low Power Stereo I2C CODEC
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the Realtek ALC5645 codec driver. It is the base
version that because the jack detect function is not implemented to
it, the headphone and AMIC1 are not workable. We will fill up the
further functions later.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch removes the i2c bus code from the codec driver and creates seperate i2c driver.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TI STA350 is an integrated 2.1-channel power amplifier that is
controllable over I2C. This patch adds an ASoC driver for it.
At a glance, this chip is very similar to the STA320 for which a driver
already exists. In details, however, the register maps contain subtle
differences which made a whole new driver easier to write and maintain.
[daniel@zonque.org: cleanups, DT property rework, rebased on asoc-next]
Signed-off-by: Sven Brandau <brandau@gmx.de>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Cirrus Logic CS42448/CS42888 Audio CODEC that
has six/four 24-bit AD and eight 24-bit DA converters.
[ CS42448/CS42888 supports both I2C and SPI control ports. As initial patch,
this patch only adds the support for I2C. ]
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This commit adds a bare bones driver support for TLV320AIC31XX family
audio codecs. The driver adds basic stereo playback trough headphone
and speaker outputs and mono capture trough microphone inputs.
The driver is currently missing support at least for mini DSP features
and jack detection. I have tested the driver only on TLV320AIC3111,
but based on the data sheets TLV320AIC3100, TLV320AIC3110, and
TLV320AIC3120 should work Ok too.
The base for the implementation was taken from:
git@gitorious.org:ti-codecs/ti-codecs.git ajitk/topics/k3.10.1-aic31xx
-branch at commit 77504eba0294764e9e63b4a0c696b44db187cd13.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The tlv320aic32x4 related lines were wrongly placed after tlv320aic3x lines.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move to the new style of defining the bus interfaces in separate modules
in order to simplify dependencies.
Signed-off-by: Mark Brown <broonie@linaro.org>
tlv320aic23 chip control interface may work in either I2C or SPI mode
depending on the MODE pin state. Functionality and register layout are
independent of the control mode.
Implement bus-specific parts as separate modules.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SiRF internal audio codec is integrated in SiRF atlas6 and prima2 SoC.
Features include:
1. Stereo DAC and ADC with 16-bit resolution amd 48KHz sample rate
2. Support headphone and/or speaker output
3. Integrate headphone and speaker output amp
4. Support LINE and MIC input
5. Support single ended and differential input mode
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
--v5:
1. Drop all inlines.
2. Reordering the Kconfig and Makefile
3. Remove the sirf_audio_codec_reg_bits struct, use the new controls instead it.
4. Add some SND_SOC_DAPM_OUT_DRV instead of HP and SPK enable driver
5. Add audio codec clock supply instead of adc event callback
6. Fixed playback and capture can't concurrent work bug.
--
.../devicetree/bindings/sound/sirf-audio-codec.txt | 17 +
sound/soc/codecs/Kconfig | 5 +
sound/soc/codecs/Makefile | 1 +
sound/soc/codecs/sirf-audio-codec.c | 533 ++++++++++++++++++++
sound/soc/codecs/sirf-audio-codec.h | 75 +++
5 files changed, 631 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/sound/sirf-audio-codec.txt
create mode 100644 sound/soc/codecs/sirf-audio-codec.c
create mode 100644 sound/soc/codecs/sirf-audio-codec.h
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the ADAU1977, ADAU1978 and ADAU1979 audio CODEC
devices. They are a family of 4-channel differential input audio ADC devices.
They can be connected to either a SPI or I2C bus. The driver is implemented in
three modules, one main module (adau1977.ko) which implements the device logic
and one module each for SPI (adau1977-spi.ko) and I2C (adau1977-i2c.ko) bus
access.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register. Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus, allows the registration of the other bus drive
to continue without problems if one of them fails.
This patch splits the ADAV80X driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register? Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus allows the registration of the other bus driver
to continue without problems if one of them fails.
This patch splits the ssm2602 driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
While we are at it also cleanup the include section of the ssm2602 driver and
remove unneeded includes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register? Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus, allows the registration of the other bus driver
to continue without problems if one of them fails.
This patch splits the AD193X driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The PCM512x devices are a family of monolithic CMOS integrated circuits
that include a stereo digital-to-analog converter and additional support
circuitry.
This is an initial driver which supports some core functionality for the
device which covers common use cases but does not cover all features.
Currently only slave clocking modes with automatic clock configuration
are supported and most of the DSP configuration for the device is not
enabled.
Signed-off-by: Mark Brown <broonie@linaro.org>
The wm8997 is a compact, high-performance audio hub CODEC with SLIMbus
interfacing, for smartphones, tablets and other portable audio devices
based on the Arizona platform.
This patch adds the wm8997 CODEC driver.
[Fixed some interface churn from bitrot due to the patch not going via
the MFD tree as expected -- broonie]
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add PCM1792A spi mode codec support. This version implements only
a subset of functionalities. Tested connect to a pandaboard ES
device and based on recently pcm1681 codec.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
PCM1681 can be controlled via I2C, SPI or in bootstrap mode (no control mode). This code add
support only for I2C mode.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ak4554 is very simple DA/AD converter which has no setting register.
Note that it has hard coded asymmetric data format
playback : SND_SOC_DAIFMT_RIGHT_J
capture : SND_SOC_DAIFMT_LEFT_J
This driver has single DAI and doesn't have set_fmt.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the ALC5640 codec driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
to support HDMI on CSR SiRFprimaII and atlasVI, we need one more HDMI pseudo
codec, rather than add a new driver, we can make omap HDMI codec common for
other SoCs as well. then the omap-hdmi codec becomes a generic HDMI pseudo-
codec as HDMI audio features depend on HDMI specification not on SoCs.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a ASoC CODEC driver for the SSM2516. The SSM2516 is a stereo
Class-D audio amplifier with an I2S interface for audio in and a built-in
dynamic range control processor.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DFBM-CS320 is only one of bluetooth modules using CSR bluetooth chips,
we don't want everyone to have a seperate codec driver. anyway, the
feature of Bluetooth SCO is same on all platforms, so this patch
makes the DFBM-CS320 driver become a common BT SCO link driver.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Transceiver usually means receiver + transmitter. This codec can do only
transmit. Update driver accordingly.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a driver for TI's TA5086 6-channel PWM processor.
This chip has a very unusual register layout, specifically because the
registers are of unequal size, and multi-byte registers require bulk
writes to take effect. Regmap does not support these kind of mappings.
Currently, the driver does not touch any of the registers >= 0x20, so
it doesn't matter, because the register map is mapped to an 8-bit array.
In case more features will be added in the future that require access
to higher registers, the entire regmap H/W I/O routines have to be
open-coded.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds a driver for Asahi Kasei's AK5386 Single-ended 24-Bit 192kHz
delta-sigma ADC. The device has no control port interface but an
optional RESET/PDN GPIO pin.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Dialog DA7213 audio codec.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the max98090 codec prototype driver.
It supports Headphone only at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many current Wolfson devices feature DSPs based around an architecture
known as ADSP. Since there is a lot of commonality in the system
integration of these devices a common library will be used to provide
support for them.
This version provides equivalent support for ADSP1 to that currently
included in the WM2200 driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit add a sound codec driver for Silicon Laboratories 476x
series of AM/FM radio chips.
Signed-off-by: Andrey Smirnov <andrey.smirnov@convergeddevices.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Dialog semiconductor's DA9055 audio codec.
This has been tested on DA9055 EVB with Samsung SMDK6410 board.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM0010 is a compact digital signal processor that has been
highly optimised for low-power audio applications. Extensive memory
resources and core optimisation allow the device to manage all audio
processing algorithms efficiently and autonomously, while the host
processor sleeps or performs other tasks.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5110 is a highly integrated low power audio subsystem for
smartphones, tablets and other portable audio devices. It combines
an advanced DSP feature set with a flexible, high performance audio
hub CODEC.
This patch adds the audio CODEC driver for the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The STA529 is a digital stereo class-D audio amplifier. It includes an
audio DSP, an ST proprietary high-efficiency class-D driver and CMOS
power output stage. It is intended for high-efficiency
digital-to-power-audio conversion for portable applications.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise we fail to link when building as modules due to multiple
init/exit functions.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the support for spdif in audio codec.
Signed-off-by: vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5102 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices based on the Arizona platform.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Wolfson Arizona series of audio hub CODECs can share a large amount
of their driver code as the result of a common register map. This patch
adds some of this core support, providing a basis for the initial WM5102
audio driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Dialog DA732x audio codecs.
Signed-off-by: Michal Hajduk <Michal.Hajduk@diasemi.com>
Signed-off-by: Adam Thomson <Adam.Thomson@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add codec-driver for ST-Ericsson AB8500 mixed-signal ASIC.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: Support TI Isabelle Audio driver
The Isabelle Audio IC is a complete low power high fidelity CODEC with integrated
ADCs, DACs, decimation and interpolation filters, PLL, and power providers. This
device supports 2 analog and 2 digital microphone channels, a mono earpiece driver,
stereo class G headphone drivers with ultra low power and best SNR in the industry,
stereo Class D speaker drivers, and 2 high performance Line drivers.
The below patch is a basic driver code for TI Isabelle audio codec. The
functionalities like headset detection, etc., will be included incrementally
in the up-coming patches.
Signed-off-by: Vishwas A Deshpande <vishwas.a.deshpande@ti.com>
Signed-off-by: M R Swami Reddy <mr.swami.reddy@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce codec for HDMI. At the moment, this is a dummy codec. In the
future it will parse the EDID to modify the supported parameters, such
as the number of channels and the sample rates. At the moment, it blindly
supports all the sample rates and audio channels described in the HDMI
1.4a specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Cirrus Logic CS42L52 Low Power Stereo Codec
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Georgi Vlaev <joe@nucleusys.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ML26124-01HB/ML26124-02GD is 16bit monaural audio CODEC which has high
resistance to voltage noise. On chip regulator realizes power supply rejection
ratio be over 90dB so more than 50dB is improved than ever. ML26124-01HB/
ML26124-02GD can deliver stable audio performance without being affected by noise
from the power supply circuit and peripheral components. The chip also includes
a composite video signal output, which can be applied to various portable device
requirements. The ML26124 is realized these functions into very small package
the size is only 2.56mm x 2.46mm therefore can be construct high quality sound
system easily.
ML26124-01HB is 25pin WCSP package; ML26124-02GD is 32pin WQFN package.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a driver supporting the volume control and the mute pin. Shdn pin
and DAPM are not taken care of yet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM2200 is a low power mobile CODEC with enhanced Wolfson myZone
Ambient Noise Cancellation (ANC) intended for mobile telephony
applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that the mfd is using the register map cache there's no need for the
CODEC driver to do any register cache management or any funny dances to
interact with the other drivers using the device so just remove the cache
initialisation and volatility information.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It has been pointed out previously, that the firmware subsystem is not the right
place for the SigmaDSP firmware loader. Furthermore the SigmaDSP is currently
only used in audio products and we are aiming for better integration into the
ASoC framework in the future, with support for ALSA controls for firmware
parameters and support dynamic power management as well. So the natural choice
for the SigmaDSP firmware loader is the ASoC subsystem.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Cirrus Logic CS42L73 low power stereo
codec.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Georgi Vlaev <joe@nucleusys.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver implements basic functionality, using I²C for the control
channel.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Having a separate list for amps is a little confusing now the official
driver model for them is the same as for other CODECs so let's sort them
into the CODEC list, but only do this for those that are actual CODEC
drivers so it's easier to remember which ones need updating.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is currently named "TVL" instead of "TLV".
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5100 is a highly integrated low power audio subsystem with advanced
digital signal processing capabilities including effects, speech clarity
enhancement and active noise cancellation. This initial driver provides
support for basic audio paths, further patches will provide more
complete functionality.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This patch adds support for the Analog Devices ADAU1373 audio codec.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For marketing reasons the part will be called WM8996. In order to avoid
user confusion rename the driver to reflect this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The WM8983 is a low power, high quality stereo CODEC
designed for portable multimedia applications. Highly flexible
analogue mixing functions enable new application features,
combining hi-fi quality audio with voice communication.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Analog Devices ADAV801 and ADAV803 audio codec.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
[zonque@gmail.com: transform to new ASoC structure]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
[zonque@gmail.com: transform to new ASoC structure]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Analog Devices ADAU1701 SigmaDSP.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A driver for the AK4641 codec used in iPAQ hx4700 and Glofiish M800
among others.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1250-EV1 Springbank audio I/O module for the Wolfson Glenfarclas
reference platform provides a simple audio I/O with an independant clock
domain, intended to simulate cellular modem and bluetooth subsystems
within the platform.
The card supports some limited GPIO based control but this is currently not
implemented.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The WM8915 is an ultra low power mobile CODEC designed for smartphones,
featuring a mixture of digital and analogue I/O with flexible mixing
options and advanced low power accessory detection functionality in a
compact package.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds the MAX98095 CODEC driver.
Signed-off-by: Peter Hsiang <peter.hsiang@maxim-ic.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DSP2 on the WM8958 has a default ROM which provides a multi-band
compressor for enhanced performance on mobile devices but can also
support runtime download of alternative firmware. In preparation for
more exploiting this functionality refactor the code to split the
handling of DSP2 into a separate file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds ASoC support for the MAX9850 codec with headphone
amplifier.
Supported features:
- Playback
- 16, 20 and 24 bit audio
- 8k - 48k sample rates
- DAPM
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a codec driver for the dfbmcs320 bluetooth module, which is used
on the neo1973 boards.
The patch also modifies the neo1937_wm8753 sound board driver to use the new
driver instead of registering the bluetooth DAI manually.
Previously there was a name mismatch between the bluetooth DAI and the bluetooth
DAI link and the sound card was not instantiated, with this patch the issue is
no longer present and sound support works again.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
