This patch adds the MediaTek MT6351 codec driver.
MT6351 communicate with SoC through MediaTek PMIC wrapper.
MT6351 use MediaTek proprietary audio interface.
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the initial amplifier driver for rt1305/rt1306.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Texas Instruments's PCM1789 DAC support.
It is a simple DAC and does not have many registers.
One particularity about this DAC is that the clocks must be
always enabled. Also, an entire software reset is necessary
while starting to play a sound otherwise, the clocks are not
synchronized (so the DAC is not able to send data).
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Motorola CPCAP is a PMIC with audio functionality, that can be
found on Motorola Droid 4 and probably a few other phones from
Motorola's Droid series.
The driver has been written from scratch using Motorola's Android
driver, register dumps from running Android and datasheet for NXP
MC13783UG (which is similar to Motorola CPCAP, but not the same).
The chip provides two audio interfaces, that can be muxed to two
different audio codecs. One provides support for stereo output
(named StDAC or HiFi), while the other only provides mono output
(named Voice). Only the Voice codec provides a Capture interface.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support of the ROHM BD28623MUV
Class D speaker amplifier for Flat-panel TVs.
This IC delivers an output power of 20W + 20W.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max9759 is a gpio controlled amplifier.
Tested on a Variscite Dart MX6 SoM based custom board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AK5558 is a 32-bit, 768 kHZ sampling, differential input ADC
for digital audio systems.
Datasheet is available at:
https://www.akm.com/akm/en/file/datasheet/AK5558VN.pdf
Initial patch includes support for normal and TDM modes.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Junichi Wakasugi <wakasugi.jb@om.asahi-kasei.co.jp>
[initial coding for 3.18 kernel]
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
[cleanups and porting to 4.9 kernel]
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
[tdm support]
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
[pm support, cleanups and porting to latest kernel]
Signed-off-by: Mark Brown <broonie@kernel.org>
The AK4458 is a 32-bit 8ch Premium DAC that corresponds
to a 768kHz PCM input and an 11.2MHz DSD input at maximum.
It supports I2S, DSD and TDM modes with 24 or 32 bit MSB
or 16, 24, 32 LSB formats. Its datasheet is available here:
https://www.akm.com/akm/en/file/datasheet/AK4458VN.pdf
Signed-off-by: Junichi Wakasugi <wakasugi.jb@om.asahi-kasei.co.jp>
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Cosmin-Gabriel Samoila <cosmin.samoila@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This codec was used in MFLD systems in the PMIC chip, we no longer have
users for this, so remove it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently there is no support for TSCS42xx audio CODECs.
Add support for TSCS42xx audio CODECs.
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Steven Eckhoff <steven.eckhoff.opensource@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is an initial version of the PCM186x codec driver supporting both
2-channel and 4-channel device variants. Not all device features are
supported yet such as master/slave mode PLL configuration for which the
codec driver currently relies on the PCM186x built-in clock
auto-detection feature or the connection of digital microphones.
However here is what's here and what should work:
- Support for SPI and I2C low-level interfaces
- Regmap support and basic register definitions
- Input Mixer and Mux selection
- I2C, LJ, and TDM DAI format support
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Texas Instruments TAS6424 device is a high-efficiency quad-channel
Class-D audio power amplifier. Its digital time division multiplexed
(TDM) interface enables up to 2 devices to share the same bus,
supporting a total of eight channels from one audio serial port.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The main rt5514 driver optionally calls into the SPI back-end to load
the firmware. This causes a link error when one driver selects rt5514
as built-in and another driver selects rt5514-spi as a loadable module:
sound/soc/codecs/rt5514.o: In function `rt5514_dsp_voice_wake_up_put':
rt5514.c:(.text+0xac8): undefined reference to `rt5514_spi_burst_write'
As a workaround, this adds another silent symbol, to force rt5514-spi
to be built-in for that configuration. I'm not overly happy with
that solution, but couldn't come up with anything better. Using
'IS_REACHABLE()' would break the case that relies on the loadable
module, and all other ideas would result in more complexity.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the new ac97 bus model, where devices are automatically
discovered on AC-Links.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the new ac97 bus model, where devices are automatically
discovered on AC-Links.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the new ac97 bus model, where devices are automatically
discovered on AC-Links.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Cirrus Logic CS43130 codec.
Support:
I2S/DSP PCM playback.
DoP/DSD playback.
HP detection and DC/AC impedance measurement.
Signed-off-by: Li Xu <li.xu@cirrus.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
on some board use enable pin to control dmic start and stop,
so add this feature in dmic driver.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
WM8524 is a 24-bit 192KHz stereo digital/analog converter (DAC) with
integral charge pump and a simple hardware control interface.
Product information can be found at:
https://www.cirrus.com/products/wm8524/
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT274 is a HD-A/SOC dual mode codec. This is the initial codec driver
of SOC mode.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It adds ASoC driver for AUD96P22 stereo audio codec integrated on ZTE
ZX family SoCs. The driver includes the support for a number of volume
and mute controls, and power bits for various playback and recording
components.
Due to that the board for testing only supports playback, recording
support is untested.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Without CONFIG_I2C, we get a build failure:
sound/soc/codecs/es8316.c:633:1: error: data definition has no type or storage class [-Werror]
sound/soc/codecs/es8316.c:633:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
sound/soc/codecs/es8316.c:633:1: error: parameter names (without types) in function declaration [-Werror]
sound/soc/codecs/es8316.c:623:26: error: 'es8316_i2c_driver' defined but not used [-Werror=unused-variable]
This adds the required Kconfig dependency.
Fixes: b8b88b7087 ("ASoC: add es8316 codec driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a codec driver for the Everest ES8316, based on code provided by
David Yang from Everest Semi.
I limited the functionality to items where the vendor code was clear,
and things that can be tested on the Weibu F3C (Intel Cherry Trail).
As a result the initial implementation only supports running in slave
mode at single speed (up to 48kHz sample rate) using I2S. HPD is not
supported.
Signed-off-by: David Yang <yangxiaohua@everest-semi.com>
[drake@endlessm.com: significant cleanups and simplifications,
remove dead/unclear code]
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for NAU88L24.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds the ADI AU1761 audio codec as a selectable option
in the kernel config. Currently the driver can only be selected
for ADI blackfin devices or if SND_SOC_ALL_CODECS is enabled.
Signed-off-by: Bryce Ferguson <bryce.ferguson@rockwellcollins.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dio2125 is a stereo output driver with adjustable gain.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Cirrus Logic
CS35L35 9V Boosted Amplifier
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The es7134 is 24bit, 192Khz i2s DA converter for PCM audio.
Datasheet is available here : http://www.everest-semi.com/pdf/ES7134LV%20DS.pdf
This driver is also compatible with the es7144, which is the same as the
es7134, with 2 additional pins for filtering capacitors.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The two front-ends to the codec can now be selected individually, but fail to
build when the bus support is missing:
sound/built-in.o: In function `es8328_spi_probe':
es8328-spi.c:(.text+0x125854): undefined reference to `__devm_regmap_init_spi'
sound/built-in.o: In function `es8328_spi_driver_init':
es8328-spi.c:(.init.text+0x3589): undefined reference to `__spi_register_driver'
Related to this, the added dependency on SND_SOC_ES8328 breaks:
warning: (SND_SOC_ALL_CODECS) selects SND_SOC_ES8328_I2C which has unmet direct dependencies (SOUND && !M68K && !UML && SND && SND_SOC && SND_SOC_ES8328 && I2C)
This adds the respective Kconfig dependencies and changes SND_SOC_ES8328 to a hidden
symbol that is selected implicitly by the two more specific options, as we do for
some other codecs. We have to remove the 'depends on' for SND_SOC_IMX_ES8328 in the
same step to avoid a recursive dependency.
Fixes: aa00f2c8af ("ASoC: Allow to select ES8328_I2C and ES8328_SPI directly")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, we have to select these symbols explictly via Kconfig, from
another entry. If we plan to use generic audio drivers like
simple-audio-card, the user need to be able to enable these symbols
directly via the menuconfig.
This commit also fixes unmet dependencies to SND_SOC_IMX_ES8328 caused
by these changes.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CQ0093VC is no longer dependent on MFD_DAVINCI_VOICECODEC,
let's remove it. Otherwise, we can't compile it by COMPILE_TEST
on non-DAVINCE platform
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm9081 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C)
And, this patch adds "depends on I2C" to Kconfig
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
uda1380 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C), and use module_i2c_driver().
And, this patch adds "depends on I2C" to Kconfig
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Cirrus Logic CS42L42 codec. SoundWire support
is not enabled. Features support for I2C control and I2S audio.
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4c5d146929 ("ASoC: max98504: Add max98504 speaker amplifier
driver") added new max98504, but this patch didn't add it to
SND_SOC_ALL_CODECS. This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the wm8581 codec to the wm8580 driver.
The wm8581 codec hardware adds a fourth DAC and otherwise is
compatible with the wm8580 codec.
of_device_id data is used to allow the driver to select the
suitable DAC count specified in the device tree codec selection.
The wm8580_driver_data struct is used to store the number of DACs.
The snd_soc_dai_driver no longer lists the channels_max for the
playback substream. This variable is set during the i2c probe
from the of_device_id supplied wm8580_driver_data struct.
With knowledge of the number of DACs in use, the DAC4 controls,
widgets and routes are added as required for DAC4.
The device tree documentation for the wm8580 is altered to list
the wm8581 codec support, as is the Kconfig file.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts(Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Digital part of the Codec which is integrated
into Application Processor.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts (Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Analog part of the Codec which is integrated
into PMIC PM8916.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the wm9712 driver still uses custom snd_soc_codec_driver IO
callbacks. This has been deprecated for a while, so convert the wm9705
driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the wm9712 driver still uses custom snd_soc_codec_driver IO
callbacks. This has been deprecated for a while, so convert the wm9712
driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit of the Cirrus Logic cs35l34 8V boosted class D
amplifier.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the initial codec driver for both rt5663 rt5668 codec.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is for codec NAU88C10 of Nuvoton Technology Corporation.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds driver for the MAX98504 speaker amplifier. The MAX98504
is a high efficiency mono class D amplifier that features an integrated
boost converter with voltage and current sensing ADCs for Dynamic Speaker
Management.
This driver does not include support for the I2S DAI, as we wouldn't be
able to test such code in a hardware configuration where the amplifier
has only wired the analogue input.
Signed-off-by: Inha Song <ideal.song@samsung.com>
[k.kozlowski: rebased on 4.1]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[s.nawrocki: removed unused macro definitions, rewrote regulator supply
related parts, rewrote regmap configuration code, added support for speaker
enable and global chip enable through DAPM, rewritten as component driver,
added PDM DAI definition and TDM callbacks for PDM channels configuration]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
--
Changes since v2:
- added parsing of the VBAT brownout DT properties,
- removed MAX98504_REG_SPEAKER_SOURCE_SELECT register initialization,
- removed unused macro definitions.
Changes since v1:
- none.
Changes since initial version:
- added regulator supply handling,
- added DAPM widges for speaker source selection,
- added PDM DAI definition and TDM callbacks for setting up active
PDM Tx channels and I/V sense ADC data mapping,
- removed all optional DT properties, added regulator supply properties
in the DT binding.
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit of the Cirrus Logic cs35l33 8V boosted class D
amplifier.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I just added an I2C dependency to the wm8985 driver to work around
a build failure, but it turns out that was premature: we actually
need to depend on SND_SOC_I2C_AND_SPI, as the driver can work with either
of the two, and we only need to prevent a configuration that has
I2C=m and SND_SOC_WM8985=y.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 05252513fb ("ASoC: wm8985: add i2c dependency")
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8985 driver is now user-selectable, but building it with
I2C disabled results in a link failure:
sound/built-in.o: In function `wm8985_i2c_probe':
:(.text+0x44914): undefined reference to `__devm_regmap_init_i2c'
sound/built-in.o: In function `wm8985_exit':
:(.exit.text+0x3d8): undefined reference to `i2c_del_driver'
sound/built-in.o: In function `wm8985_modinit':
:(.init.text+0x1454): undefined reference to `i2c_register_driver'
This adds a Kconfig dependency the way that the other codec
drivers have it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 811e66de22 ("ASoC: wm8985: add support for WM8758")
Signed-off-by: Mark Brown <broonie@kernel.org>
Multiple devices from the ADAU family share the same PLL structure and
configuration register layout. Introduce a new helper module that can be
used to calculated the PLL configuration registers based on a specified
input frequency and the desired output frequency of the PLL.
The ADAU1761/ADAU1781 and ADAU1373 drivers are updated to make use of this
new helper module. But future drivers for additional devices from the ADAU
family are also expected to make use of it.
In anticipation of sharing more infrastructure code between different
devices from the ADAU family the new module is called adau-utils.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The device has multiple control interfaces, I2C and SPI. The I2C interface
mainly controls the register settings of codec. The SPI interface is in
order to provide the high speed transmission of data. For example, high
bandwidth memory read/write of DSP. The patch adds the rt5514 SPI driver
for loading the firmware of DSP and retrieving the voice data from DSP
after the system is waked up by specific voice.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the ADAU7002 PDM-to-I2S/TDM converter. The
ADAU7002 takes a stereo PDM signal (e.g. from two digital microphones) and
converts it into a I2S/TDM PCM stream. The chip does not have a
programmable control interface and the driver simply describes the static
capabilities of the chip.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_HDMI_CODEC can be enabled without HDMI support, leading
to a link error:
In function `hdmi_codec_hw_params':
sound/soc/codecs/hdmi-codec.c:188: undefined reference to `hdmi_audio_infoframe_init'
sound/built-in.o:(.debug_addr+0x1a5c0): undefined reference to `hdmi_audio_infoframe_init'
This changes the Kconfig file to select HDMI, as the other codec using
hdmi_audio_infoframe_init already does.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8758 chip is almost identical to WM8985 with the difference that it
doesn't feature the AUX input. This patch adds the WM8758 support into the
WM8985 driver.
The chip selection is done by the I2C name. The SPI probe supports only
the WM8985.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a driver for the MAX9860 Mono Audio Voice Codec.
https://datasheets.maximintegrated.com/en/ds/MAX9860.pdf
This driver does not support sidetone since the DVST register field is
backwards with the mute near the maximum level instead of the minimum.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
CS53L30 is a Quad-Channel ADC from Cirrus Logic with an I2S/TDM DAI.
So this patch adds a codec driver for CS53L30 that includes 4-channel
24-bit recording and TDM mode supports.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some definitions to support the PCM5102A codec
by Texas Instruments.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Changes to original patch by Florian Meier:
* rebased (Makefile and Kconfig
* fixed checkpath errors (spaces, newlines)
* added dt-binding documentation
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Texas Instruments TAS5720L/M device is a high-efficiency mono
Class-D audio power amplifier optimized for high transient power
capability to use the dynamic power headroom of small loudspeakers.
Its digital time division multiplexed (TDM) interface enables up to
16 devices to share the same bus.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for running the tlv32x4 control channel over SPI rather than I2C.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
To prepare for abstracting adding SPI support, the I2C pieces needs to
be in its own moudle. This patch moves common probe code into aic32x4_probe
and common removal code into aic32x4_remove. It also creates a static
regmap config structure to be copied in the I2C specific driver.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hdmi-codec is a platform device driver to be registered from
drivers of external HDMI encoders with I2S and/or spdif interface. The
driver in turn registers an ASoC codec for the HDMI encoder's audio
functionality.
The structures and definitions in the API header are mostly redundant
copies of similar structures in ASoC headers. This is on purpose to
avoid direct dependencies to ASoC structures in video side driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that this is directly user selectable it needs to care about its
dependencies.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide a menu selection text so that users can enable, disable or
mark it as module in menuconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5616 codec registers itself as an i2c driver, but can
be enabled even when i2c is turned off, which leads to a build
error:
codecs/rt5616.c:1419:1: error: data definition has no type or storage class [-Werror]
module_i2c_driver(rt5616_i2c_driver);
This adds an explicit Kconfig dependency, like the other codec
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 288bc356a8 ("ASoC: rt5616: allow to build with CONFIG_SND_SOC_RT5616")
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes that hasn't built the rt5616 driver with
'CONFIG_SND_SOC_RT5616=y' in .config.
The tristate is the prompt on the 'make menuconfig',
in other words, that can't show the prompt and select it
if we don't say what's the tristate.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Uses the drm ELD core framework to apply rate and channel
Also compute the format to be set based on ELD.
Even though the channel constraint is based on ELD, infoframe
is set with stereo only. Multichannel support will be added
later.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the initial codec driver for rt5514. The codec includes a low power
DSP for voice wake up. The register address is incremental by 4 in the DSP
memory map. In order to recover the codec settings in the codec mode and
manipulate the DSP mode for voice wake up, we use the multi-level register
map. One is for ALSA API in codec mode that can be recovered by cache
before recording. Another is for DSP related settings that can be accessed
with 32bit address of the DSP in the application of voice wake up.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PCM179x family supports both SPI and I2C. This patch adds support
for the I2C interface.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pcm179x family supports both SPI and I2C for configuration. This
patch splits the driver into core and SPI parts, in preparation for
I2C support.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When SND_SOC_INNO_RK3036 is enabled but REGMAP_MMIO is not, the MODPOST
step fails with this error:
...
Kernel: arch/x86/boot/bzImage is ready (#3)
Building modules, stage 2.
MODPOST 3203 modules
ERROR: "__devm_regmap_init_mmio_clk" [sound/soc/codecs/snd-soc-inno-rk3036.ko] undefined!
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Mark Brown <broonie@kernel.org>
pcm1792a is compatible with pcm1795 and pcm1796 so it's
better to have them under the common name pcm179x
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Register a platform driver for the CODEC and add DAIs that will be used
to connect a compressed record path for the voice control functionality.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds devicetree support to the wm8974 codec driver.
With a DT-based kernel, there is no board-specific setting
to select the driver so allow it to be manually chosen.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for Texas Instruments pcm3168a codec
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for DA7217 and DA7218 audio codecs.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RK3036 SoC integrated with an Inno audio codec.
This driver implements the functions of it.
There is not need a special machine driver, since the
simple-card machine driver works perfect in this case.
Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since driver use infoframe symbols from video/hdmi.c we should select this
symbol for this driver
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds HDA based HDMI driver to be used in platforms like SKL
and onwards
Register the hdmi driver with hda bus and register dais.
Also parse the widget and initialize identified pin and converter
widgets.
For simplification, currently only one pin and one converter
widget are enabled on board, as well as limit the rates supported
to simples ones and not based on ELD. This things will come
eventually once basic support for this is merged
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the Wolfson WM9713 to regmap API. This will leverage all the
regmap functions (debug, registers update, etc ...).
As a bonus, this will pave the path to gpio chip introduction, and
devicetree support. This was tested on the mioa701 board, pxa27x based,
in PCM playback, and through suspend/resume.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Cirrus Logic CS47L24 and WM1831 codecs.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for the DA7219 audio codec with built-in advanced
accessory detect features.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hdmi stub codec has not been used since refactoring of OMAP HDMI
audio support.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the InvenSense ICS-43432 I2S MEMS microphone.
This is a non-software-configurable MEMS microphone with I2S output.
Tested on a setup with a single ICS-43432 (the device itself supports
stereo operation using a hardware pin controlling left vs. right channel
output).
Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Codec part of the sti platform that supports codec IPs.
This first version does not support HDMI, but only DAC and SPDIF out.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver add PCM interface to a GTM601 UMTS modem chip.
There is no configuration interface.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch separates the IO function from the rt286. It is prepared to share
for new chips that support the same IO function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make generic ASoC AC'97 CODEC selectable in config.
This way this driver can be used for platforms which don't need
specialized AC'97 CODEC drivers but which are not directly
selectable in config themselves (for example DT based ones).
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit aa0e25caaf ("ASoC: da7210: Add support for spi regmap"),
the da7210 codec driver supports both I2C and SPI buses.
Thus update the dependency accordingly.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce a new codec driver for the Texas Instruments
TAS5711/TAS5717/TAS5719 power amplifier chips. These chips are typically
used to take an I2S digital audio input and drive 10-20W into a pair of
speakers.
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify dependencies by using new style split out bus interfaces.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max98357a driver depends on GPIOLIB. This may cause the following
build failure.
sound/soc/codecs/max98357a.c: In function 'max98357a_daiops_trigger':
sound/soc/codecs/max98357a.c:30:3: error: implicit declaration of function 'gpiod_set_value'
sound/soc/codecs/max98357a.c: In function 'max98357a_codec_probe':
sound/soc/codecs/max98357a.c:55:2: error: implicit declaration of function 'devm_gpiod_get'
sound/soc/codecs/max98357a.c:61:2: error: implicit declaration of function 'gpiod_direction_output'
Seen with mips:allmodconfig as well as various randconfig builds.
Fixes: af5adf1293 ("ASoC: max98357a: Add MAX98357A codec driver")
Cc: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add codec driver for the Maxim MAX98357A DAC.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Acked-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5677 codec has gained code that requires SPI to work correctly,
but there is no provision in Kconfig to prevent the driver from
being used when SPI is disabled or a loadable module, resulting
in this build error:
sound/built-in.o: In function `rt5677_spi_write':
:(.text+0xa7ba0): undefined reference to `spi_sync'
sound/built-in.o: In function `rt5677_spi_driver_init':
:(.init.text+0x253c): undefined reference to `spi_register_driver'
ERROR: "spi_sync" [sound/soc/codecs/snd-soc-rt5677-spi.ko] undefined!
ERROR: "spi_register_driver" [sound/soc/codecs/snd-soc-rt5677-spi.ko] undefined!
This makes the SPI portion of the driver depend on the SPI subsystem,
and disables the function that uses SPI for firmware download if SPI
is disabled. The latter may not be the correct solution, but I could
not come up with a better one.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: af48f1d08a ("ASoC: rt5677: Support DSP function for VAD application")
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add description for the driver
- Add dependency on the I2C module
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
use the regmap API directly rather than relying on the snd_soc_read/write
functions as this seems to be in accordance with common practice.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec driver uses regmap to do i2c read/write.
The codec driver started to use REGMAP_IRQ since:
5e3363ad1b
ASoC: rt5677: add GPIO IRQ support
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch converts the ad1980 driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TS3A227E is an autonomous audio accessory detection and
configuration switch that detects 3-pole or 4-pole audio accessories
and configures internal switches to route the signals accordingly.
This chip also has built-in support for the new button standard
described in the Android "Wired audio headset specification" v1.0.
These buttons will be reported on the jack as buttons 0-3 mapped to
KEY_MEDIA, KEY_VOLUMEUP, KEY_VOLUMEDOWN, and KEY_VOICE_COMMAND.
This will be added as an aux_dev and have the jack passed in from the
machine driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes build errors in configurations with I2C/SPI master disabled.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix build errors when CONFIG_I2C is not enabled by making the
driver depend on I2C.
../sound/soc/codecs/cs42l51-i2c.c:55:1: warning: data definition has no type or storage class [enabled by default]
module_i2c_driver(cs42l51_i2c_driver);
^
../sound/soc/codecs/cs42l51-i2c.c:55:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
../sound/soc/codecs/cs42l51-i2c.c:55:1: warning: parameter names (without types) in function declaration [enabled by default]
../sound/soc/codecs/cs42l51-i2c.c:45:26: warning: 'cs42l51_i2c_driver' defined but not used [-Wunused-variable]
static struct i2c_driver cs42l51_i2c_driver = {
^
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that manual selection of drivers for audio subsystem components is
preferred AIC23 codec must be selectable in Kconfig to make it possible.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we are removing the Armada 370 DB audio machine driver to use
the 'simple-card' Device Tree binding, we can no longer select the
CS42L51 codec driver using a Kconfig 'select', and we instead need it
to be user-selectable. Therefore, this commit adds a prompt to make
the CS42L51 I2C codec driver user-selectable.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Create a separate module for rt5677 spi driver. Without
this patch, the build fails due to multiple defs of
'init_module' and 'cleanup_module'. module_spi_driver()
defines its own module, so it can't be part of the rt5677
module.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since 9cb715a9d4c the codec has a hardcoded dependency to spi.
Add this dependency to Kconfig. It fixes buildbot compilation failure:
sound/built-in.o: In function `spi_write':
>> rt5677-spi.c:(.text+0x8265f): undefined reference to `spi_sync'
sound/built-in.o: In function `rt5677_spi_driver_init':
>> rt5677-spi.c:(.init.text+0x17db): undefined reference to `spi_register_driver'
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the cs4271 driver depends on SND_SOC_I2C_AND_SPI.
So the driver cannot be built as built-in if CONFIG_I2C=m.
Split SPI and I2C code into different modules to avoid this issue.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt286 use I2C as its I/O. So the driver can only available when
I2C is selected.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow the ssm2602/ssm2603/ssm2604 codec driver to be
instantiated from the device tree.
Also, add Kconfig prompts to allow manual selection of both the
I2C and SPI configuration versions of the driver.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Analog Devices SSM4567 is a boost class-D audio amplifier.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using a DT-based multi-platform kernel, there's not always Kconfig
logic that selects the right codec driver.
Allow the user to manually select WM8978.
This is needed for Armadillo 800 EVA using a generic r8a7740 multi-platform
kernel.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a codec driver for the Everest ES8328. It supports two separate audio
outputs and two separate audio inputs.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Cirrus Logic CS35L32 Boosted Amplifier
I2S output provides monitor data to the SOC/CODEC/DSP for speaker protection/enhancement algorithms
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to show the option under 'CODEC drivers' we need to have text in
Kconfig.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The codec can be configured via I2C and using regmap_i2c.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Support the TI TAS2552 Class D amplifier.
The TAS2552 is a high efficiency Class-D audio
power amplifier with advanced battery current
management and an integrated Class-G boost
The device constantly measures the
current and voltage across the load and provides a
digital stream of this information.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds Realtek ALC286 codec driver.
ALC286 is a dual mode codec, which can run as HD-A or I2S mode.
It is controlled by HD-A verb commands via I2C protocol.
The following is the I/O difference between ALC286 and general I2S codecs.
1. A HD-A verb command contains three parts, NID, VID, and PID.
And an I2S command contains only two parts: address and data.
2. Not only the register address is written, but the read command also
includes the entire write command.
3. rt286 uses different registers for read and write the same bits.
We map verb command to regmap structure. However, we read most registers from
cache to prevent the asymmetry read/write issue in rt286.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Gustaw Lewandowski <gustaw.lewandowski@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a minimum support of Realtek ALC5670 codec.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Cirrus Logic CS4265 Stereo I2C CODEC.
Signed-off-by: Paul Handrigan <paul.handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the SigmaDSP module is built-in, but the I2C core is build as a module
we'll get a undefined reference:
sound/built-in.o: In function `sigma_action_write_i2c':
:(.text+0x5d8d4): undefined reference to `i2c_master_send'
This can happen if a audio driver that is using the regmap SigmaDSP interface is
built into the kernel, but core I2C support is build as a module. To fix this
split the SigmaDSP module into three modules, one module providing the core
infrastructure and two small modules implementing the regmap and I2C interfaces.
This allows e.g. the core infrastructure and regmap support to be built into the
kernel while I2C support can still be build as a module.
Fixes: dab464b60 ("ASoC: Add ADAU1361/ADAU1761 audio CODEC support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the SigmaDSP module is built-in, but the I2C core is build as a module
we'll get a undefined reference:
sound/built-in.o: In function `sigma_action_write_i2c':
:(.text+0x5d8d4): undefined reference to `i2c_master_send'
This can happen if a audio driver that is using the regmap SigmaDSP interface is
built into the kernel, but core I2C support is build as a module. To fix this
split the SigmaDSP module into three modules, one module providing the core
infrastructure and two small modules implementing the regmap and I2C interfaces.
This allows e.g. the core infrastructure and regmap support to be built into the
kernel while I2C support can still be build as a module.
Fixes: dab464b60 ("ASoC: Add ADAU1361/ADAU1761 audio CODEC support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch adds the RL6231 class device shared support for RT5640, RT5645 and
RT5651. The function of the DMIC clock calculation can be shared by RL6231
shared support.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Analog Devices ADAU1381 and ADAU1781 audio
CODECs. The device is a low-power, 24-bit stereo audio CODEC with multiple
analog inputs and outputs, two digital microphone inputs and an I2S interface.
The device can be controlled either using I2C or SPI. The main difference
between the two variants is that the ADAU1781 has a freely programmable SigmaDSP
processor, while the ADAU1381 has a fixed function wind noise reduction filter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Analog Devices ADAU1361 and ADAU1761 CODECs.
The device is a a low-power, 24-bit stereo audio CODEC with multiple analog
input and outputs, one digital microphone input and an I2S interface. The device
can be controlled either via I2C or SPI. The main difference between the two
variants is that the ADAU1761 has a built-in SigmaDSP, while the ADAU1361 has
not.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADAU1X61 and ADAU1X81 are very similar in the digital domain, but are quite
different in the analog domain. This patch adds support for the common parts of
the ADAU1X61 and ADAU1X81 CODECs.
The patch also restores some of the alphabetical order in the Makfile and
Kconfig.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add "depends on I2C" to shut up the build errors from randconfig.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let the ALC5623 codec be instantiated from DT. Add a simple binding
for the additional control register and the jack detect register.
Also, add a prompt to the Kconfig entry for this CODEC, so that it can
be selected. Since kirkwood-t5325.c will no longer be used, we need to
be able to enable the CODEC in the mvebu_v5_defconfig etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Cirrus Logic Low Power Stereo I2C CODEC
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the Realtek ALC5645 codec driver. It is the base
version that because the jack detect function is not implemented to
it, the headphone and AMIC1 are not workable. We will fill up the
further functions later.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Building ARM randconfig got into a situation where CONFIG_INPUT
is turned off and SND_SOC_ALL_CODECS is turned on, which failed
for two codecs trying to use the input subsystem. Some other
drivers also select one of these codecs and consequently need an
explicit dependency added.
Appending to the dependency list seems the easiest way out,
since this is not a practical limitation. If anyone really
needs to build these codecs for a kernel with no input support,
a more sophisticated solution can be implemented.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Xia Kaixu <kaixu.xia@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch removes the i2c bus code from the codec driver and creates seperate i2c driver.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TI STA350 is an integrated 2.1-channel power amplifier that is
controllable over I2C. This patch adds an ASoC driver for it.
At a glance, this chip is very similar to the STA320 for which a driver
already exists. In details, however, the register maps contain subtle
differences which made a whole new driver easier to write and maintain.
[daniel@zonque.org: cleanups, DT property rework, rebased on asoc-next]
Signed-off-by: Sven Brandau <brandau@gmx.de>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Cirrus Logic CS42448/CS42888 Audio CODEC that
has six/four 24-bit AD and eight 24-bit DA converters.
[ CS42448/CS42888 supports both I2C and SPI control ports. As initial patch,
this patch only adds the support for I2C. ]
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This commit adds a bare bones driver support for TLV320AIC31XX family
audio codecs. The driver adds basic stereo playback trough headphone
and speaker outputs and mono capture trough microphone inputs.
The driver is currently missing support at least for mini DSP features
and jack detection. I have tested the driver only on TLV320AIC3111,
but based on the data sheets TLV320AIC3100, TLV320AIC3110, and
TLV320AIC3120 should work Ok too.
The base for the implementation was taken from:
git@gitorious.org:ti-codecs/ti-codecs.git ajitk/topics/k3.10.1-aic31xx
-branch at commit 77504eba0294764e9e63b4a0c696b44db187cd13.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move to the new style of defining the bus interfaces in separate modules
in order to simplify dependencies.
Signed-off-by: Mark Brown <broonie@linaro.org>
tlv320aic23 chip control interface may work in either I2C or SPI mode
depending on the MODE pin state. Functionality and register layout are
independent of the control mode.
Implement bus-specific parts as separate modules.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SiRF internal audio codec is integrated in SiRF atlas6 and prima2 SoC.
Features include:
1. Stereo DAC and ADC with 16-bit resolution amd 48KHz sample rate
2. Support headphone and/or speaker output
3. Integrate headphone and speaker output amp
4. Support LINE and MIC input
5. Support single ended and differential input mode
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
--v5:
1. Drop all inlines.
2. Reordering the Kconfig and Makefile
3. Remove the sirf_audio_codec_reg_bits struct, use the new controls instead it.
4. Add some SND_SOC_DAPM_OUT_DRV instead of HP and SPK enable driver
5. Add audio codec clock supply instead of adc event callback
6. Fixed playback and capture can't concurrent work bug.
--
.../devicetree/bindings/sound/sirf-audio-codec.txt | 17 +
sound/soc/codecs/Kconfig | 5 +
sound/soc/codecs/Makefile | 1 +
sound/soc/codecs/sirf-audio-codec.c | 533 ++++++++++++++++++++
sound/soc/codecs/sirf-audio-codec.h | 75 +++
5 files changed, 631 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/sound/sirf-audio-codec.txt
create mode 100644 sound/soc/codecs/sirf-audio-codec.c
create mode 100644 sound/soc/codecs/sirf-audio-codec.h
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the ADAU1977, ADAU1978 and ADAU1979 audio CODEC
devices. They are a family of 4-channel differential input audio ADC devices.
They can be connected to either a SPI or I2C bus. The driver is implemented in
three modules, one main module (adau1977.ko) which implements the device logic
and one module each for SPI (adau1977-spi.ko) and I2C (adau1977-i2c.ko) bus
access.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register. Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus, allows the registration of the other bus drive
to continue without problems if one of them fails.
This patch splits the ADAV80X driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register? Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus allows the registration of the other bus driver
to continue without problems if one of them fails.
This patch splits the ssm2602 driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
While we are at it also cleanup the include section of the ssm2602 driver and
remove unneeded includes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register? Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus, allows the registration of the other bus driver
to continue without problems if one of them fails.
This patch splits the AD193X driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The PCM512x devices are a family of monolithic CMOS integrated circuits
that include a stereo digital-to-analog converter and additional support
circuitry.
This is an initial driver which supports some core functionality for the
device which covers common use cases but does not cover all features.
Currently only slave clocking modes with automatic clock configuration
are supported and most of the DSP configuration for the device is not
enabled.
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that we have a generic card driver we can't rely on the card driver
selecting the CODECs for us so make the CODECs that can be enabled with
OF directly selectable in Kconfig. For the platforms not using OF it's
not clear that we don't still want to have some board specific selection
since the kernel needs to contain code to register the devices; ACPI could
provide this from firmware does not yet support any kind of generic card.
It may also be desirable to hide these if OF is not enabled to reduce
noise.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The wm8997 is a compact, high-performance audio hub CODEC with SLIMbus
interfacing, for smartphones, tablets and other portable audio devices
based on the Arizona platform.
This patch adds the wm8997 CODEC driver.
[Fixed some interface churn from bitrot due to the patch not going via
the MFD tree as expected -- broonie]
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add PCM1792A spi mode codec support. This version implements only
a subset of functionalities. Tested connect to a pandaboard ES
device and based on recently pcm1681 codec.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
PCM1681 can be controlled via I2C, SPI or in bootstrap mode (no control mode). This code add
support only for I2C mode.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The adau1701 driver was removed from SND_SOC_ALL_CODECS in commit commit ee8c7e9
("ASoC: Remove adau1701 from SND_SOC_ALL_CODECS due to Sigma dependency") due
to the dependency on the SigmaDSP firmware loader which was only available on a
limited set of platforms. This was fixed quite some time ago in commit 40216ce7
("ASoC: Move SigmaDSP firmware loader to ASoC") though, so we can add the driver
back again to SND_SOC_ALL_CODECS.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The main function of the option is to enable compile testing. There is
still an option since COMPILE_TEST is intended to enable selection of
extra drivers rather than forcing them on.
Signed-off-by: Mark Brown <broonie@kernel.org>
ak4554 is very simple DA/AD converter which has no setting register.
Note that it has hard coded asymmetric data format
playback : SND_SOC_DAIFMT_RIGHT_J
capture : SND_SOC_DAIFMT_LEFT_J
This driver has single DAI and doesn't have set_fmt.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the ALC5640 codec driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver is useless if both SPI and I2C are not configured.
Thus don't build this driver if both SPI and I2C are not configured.
This patch silences below build warning if both SPI and I2C are not configured.
CC sound/soc/codecs/adav80x.o
sound/soc/codecs/adav80x.c:842:12: warning: 'adav80x_bus_probe' defined but not used [-Wunused-function]
sound/soc/codecs/adav80x.c:863:12: warning: 'adav80x_bus_remove' defined but not used [-Wunused-function]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
to support HDMI on CSR SiRFprimaII and atlasVI, we need one more HDMI pseudo
codec, rather than add a new driver, we can make omap HDMI codec common for
other SoCs as well. then the omap-hdmi codec becomes a generic HDMI pseudo-
codec as HDMI audio features depend on HDMI specification not on SoCs.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a ASoC CODEC driver for the SSM2516. The SSM2516 is a stereo
Class-D audio amplifier with an I2S interface for audio in and a built-in
dynamic range control processor.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DFBM-CS320 is only one of bluetooth modules using CSR bluetooth chips,
we don't want everyone to have a seperate codec driver. anyway, the
feature of Bluetooth SCO is same on all platforms, so this patch
makes the DFBM-CS320 driver become a common BT SCO link driver.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Kconfig symbol SND_SOC_OF_SIMPLE got removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC
Multi-Component Support"). But that commit missed one instance. Remove
it now, together with the prompt it has effectively hidden ever since.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a driver for TI's TA5086 6-channel PWM processor.
This chip has a very unusual register layout, specifically because the
registers are of unequal size, and multi-byte registers require bulk
writes to take effect. Regmap does not support these kind of mappings.
Currently, the driver does not touch any of the registers >= 0x20, so
it doesn't matter, because the register map is mapped to an 8-bit array.
In case more features will be added in the future that require access
to higher registers, the entire regmap H/W I/O routines have to be
open-coded.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds a driver for Asahi Kasei's AK5386 Single-ended 24-Bit 192kHz
delta-sigma ADC. The device has no control port interface but an
optional RESET/PDN GPIO pin.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
=vi6x
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
A few more updates from the past week - a new driver from Dialog and
some small fixes and tweaks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ivD5
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.9-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Final updates for v3.9
A few more updates from the past week - a new driver from Dialog and
some small fixes and tweaks.
This patch adds support for the Dialog DA7213 audio codec.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix these two compile errors on s390 which does not have HAS_IOPORT
nor GENERIC_HARDIRQS:
sound/pci/lx6464es/lx6464es.c: In function ‘snd_lx6464es_free’:
sound/pci/lx6464es/lx6464es.c:565:2: error: implicit declaration of function ‘ioport_unmap’
sound/soc/codecs/wm8903.c: In function ‘wm8903_set_pdata_irq_trigger’:
sound/soc/codecs/wm8903.c:1954:9: error: implicit declaration of function ‘irq_get_irq_data’
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the max98090 codec prototype driver.
It supports Headphone only at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many current Wolfson devices feature DSPs based around an architecture
known as ADSP. Since there is a lot of commonality in the system
integration of these devices a common library will be used to provide
support for them.
This version provides equivalent support for ADSP1 to that currently
included in the WM2200 driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use regmap-mmio instead of open-coding caching and register accessors.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit add a sound codec driver for Silicon Laboratories 476x
series of AM/FM radio chips.
Signed-off-by: Andrey Smirnov <andrey.smirnov@convergeddevices.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Dialog semiconductor's DA9055 audio codec.
This has been tested on DA9055 EVB with Samsung SMDK6410 board.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM0010 is a compact digital signal processor that has been
highly optimised for low-power audio applications. Extensive memory
resources and core optimisation allow the device to manage all audio
processing algorithms efficiently and autonomously, while the host
processor sleeps or performs other tasks.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5110 is a highly integrated low power audio subsystem for
smartphones, tablets and other portable audio devices. It combines
an advanced DSP feature set with a flexible, high performance audio
hub CODEC.
This patch adds the audio CODEC driver for the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The STA529 is a digital stereo class-D audio amplifier. It includes an
audio DSP, an ST proprietary high-efficiency class-D driver and CMOS
power output stage. It is intended for high-efficiency
digital-to-power-audio conversion for portable applications.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5102 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices based on the Arizona platform.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Wolfson Arizona series of audio hub CODECs can share a large amount
of their driver code as the result of a common register map. This patch
adds some of this core support, providing a basis for the initial WM5102
audio driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Dialog DA732x audio codecs.
Signed-off-by: Michal Hajduk <Michal.Hajduk@diasemi.com>
Signed-off-by: Adam Thomson <Adam.Thomson@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add codec-driver for ST-Ericsson AB8500 mixed-signal ASIC.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: Support TI Isabelle Audio driver
The Isabelle Audio IC is a complete low power high fidelity CODEC with integrated
ADCs, DACs, decimation and interpolation filters, PLL, and power providers. This
device supports 2 analog and 2 digital microphone channels, a mono earpiece driver,
stereo class G headphone drivers with ultra low power and best SNR in the industry,
stereo Class D speaker drivers, and 2 high performance Line drivers.
The below patch is a basic driver code for TI Isabelle audio codec. The
functionalities like headset detection, etc., will be included incrementally
in the up-coming patches.
Signed-off-by: Vishwas A Deshpande <vishwas.a.deshpande@ti.com>
Signed-off-by: M R Swami Reddy <mr.swami.reddy@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce codec for HDMI. At the moment, this is a dummy codec. In the
future it will parse the EDID to modify the supported parameters, such
as the number of channels and the sample rates. At the moment, it blindly
supports all the sample rates and audio channels described in the HDMI
1.4a specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Cirrus Logic CS42L52 Low Power Stereo Codec
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Georgi Vlaev <joe@nucleusys.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.
Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ML26124-01HB/ML26124-02GD is 16bit monaural audio CODEC which has high
resistance to voltage noise. On chip regulator realizes power supply rejection
ratio be over 90dB so more than 50dB is improved than ever. ML26124-01HB/
ML26124-02GD can deliver stable audio performance without being affected by noise
from the power supply circuit and peripheral components. The chip also includes
a composite video signal output, which can be applied to various portable device
requirements. The ML26124 is realized these functions into very small package
the size is only 2.56mm x 2.46mm therefore can be construct high quality sound
system easily.
ML26124-01HB is 25pin WCSP package; ML26124-02GD is 32pin WQFN package.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a driver supporting the volume control and the mute pin. Shdn pin
and DAPM are not taken care of yet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM2200 is a low power mobile CODEC with enhanced Wolfson myZone
Ambient Noise Cancellation (ANC) intended for mobile telephony
applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently SND_SOC_JZ4740_CODEC depends on SOC_JZ4740 but SOC_JZ4740 is not
defined in any Kconfig. Thus the codec driver will not be built when select
"Build all ASoC CODEC drivers".
(Unless it is selected by SND_JZ4740_SOC_QI_LB60).
Remove the dependency with SOC_JZ4740, then this code driver can be built when
select "Build all ASoC CODEC drivers".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It has been pointed out previously, that the firmware subsystem is not the right
place for the SigmaDSP firmware loader. Furthermore the SigmaDSP is currently
only used in audio products and we are aiming for better integration into the
ASoC framework in the future, with support for ALSA controls for firmware
parameters and support dynamic power management as well. So the natural choice
for the SigmaDSP firmware loader is the ASoC subsystem.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Cirrus Logic CS42L73 low power stereo
codec.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Georgi Vlaev <joe@nucleusys.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver implements basic functionality, using I²C for the control
channel.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is currently named "TVL" instead of "TLV".
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5100 is a highly integrated low power audio subsystem with advanced
digital signal processing capabilities including effects, speech clarity
enhancement and active noise cancellation. This initial driver provides
support for basic audio paths, further patches will provide more
complete functionality.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This patch adds support for the Analog Devices ADAU1373 audio codec.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For marketing reasons the part will be called WM8996. In order to avoid
user confusion rename the driver to reflect this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@ti.com>
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
OMAP: Add debugfs node to show the summary of all clocks
OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
OMAP2+: PM: idle clkdms only if already in idle
OMAP2+: clockdomain: add clkdm_in_hwsup()
OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
OMAP4: hwmod: Introduce the module control in hwmod control
OMAP4: cm: Add two new APIs for modulemode control
OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
OMAP4: hwmod data: Add PRM context register offset
OMAP4: prm: Remove deprecated functions
OMAP4: prm: Replace warm reset API with the offset based version
OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
OMAP: hwmod: Wait the idle status to be disabled
OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
OMAP2+: hwmod: Init clkdm field at boot time
OMAP4: hwmod data: Add clock domain attribute
OMAP4: clock data: Add missing divider selection for auxclks
...
The WM8983 is a low power, high quality stereo CODEC
designed for portable multimedia applications. Highly flexible
analogue mixing functions enable new application features,
combining hi-fi quality audio with voice communication.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
