Previous debug message states that there was a failure and tx was not
disabled. Which is not true as the TX in this function could also be
enabled. Thus improve a bit the debug message by s/disable/start\/stop/.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230301113807.24036-4-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regmap_update_bits() instead of regmap_read(), running variable,
regmap_write(). There is no need for extra variables and checks around
it as regmap_update_bits() already does this. With this code becomes
simpler.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230301113807.24036-3-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Claudiu Beznea <claudiu.beznea@microchip.com>:
To start capture on Microchip PDMC the enable bits for each supported
microphone need to be set. After this bit is set the PDMC starts to
receive data from microphones and it considers this data as valid data.
Thus if microphones are not ready the PDMC captures anyway data from its
lines. This data is interpreted by the human ear as poc noises.
To avoid this the following software workaround need to be applied when
starting capture:
1/ enable PDMC channel
2/ wait 150ms
3/ execute 16 dummy reads from RHR
4/ clear interrupts
5/ enable interrupts
6/ enable DMA channel
For this workaround to work step 6 need to be executed at the end.
For step 6 was added patch 1/3 from this series. With this, component
DAI driver sets its struct snd_soc_component_driver::start_dma_last = 1
and proper action is taken based on this flag when starting DAI trigger
vs DMA.
Without modification the AT91SAM9G20-EK has no capture support, none of the
inputs of the CODEC are wired to anything to useful and there are no paths
supporting loopback. Since the audio is clocked from the CODEC and the DAPM
inputs are marked as unusable this means that capture will fail to transfer
any data as the ADC path can't be powered up.
Flag this in the device description so apps don't see unusable capture
support, guarded with the existing optional define for mic input.
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230225-asoc-sam9g20ek-v1-1-9baeb4893142@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Microchip PDMC IP doesn't filter microphone noises on startup. By default,
it captures data received from digital microphones after
the MCHP_PDMC_MR.EN bits are set. Thus when enable is set on PDMC side the
digital microphones might not be ready yet and PDMC captures data from then
in this time. This data captured is poc noise. To avoid this the software
workaround is to the following:
1/ enable PDMC channel
2/ wait 150ms (on SAMA7G5-EK setup)
3/ execute 16 dummy reads from RHR
4/ clear interrupts
5/ enable interrupts
6/ enable DMA channel
Fixes: 50291652af ("ASoC: atmel: mchp-pdmc: add PDMC driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230228110145.3770525-4-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns:
../sound/soc/atmel/mchp-spdifrx.c:455:3: error: variable 'mr' is uninitialized when used here [-Werror,-Wuninitialized]
mr |= SPDIFRX_MR_ENDIAN_BIG;
^~
../sound/soc/atmel/mchp-spdifrx.c:432:8: note: initialize the variable 'mr' to silence this warning
u32 mr;
^
= 0
1 error generated.
Zero initialize mr so that these bitwise OR and assignment operation
works unconditionally.
Fixes: fa09fa6038 ("ASoC: mchp-spdifrx: fix controls which rely on rsr register")
Link: https://github.com/ClangBuiltLinux/linux/issues/1797
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230202-mchp-spdifrx-fix-uninit-mr-v1-1-629a045d7a2f@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add runtime PM support for Microchip SPDIFRX driver. On runtime suspend
the clocks are disabled and regmap is set in caching mode. On runtime
resume the clocks are enabled and regmap is synced with the device.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-8-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
CSC interrupts which might be used in controls are on bits 8 and 9 of
SPDIFRX_IDR register. Thus disable all the interrupts that are exported
by driver.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-5-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Channel status get and channel subcode get controls relies on data
returned by controls when certain IRQs are raised. To achieve that
completions are used b/w controls and interrupt service routine. The
concurrent accesses to these controls are protected by
struct snd_card::controls_rwsem.
Issues identified:
- reinit_completion() may be called while waiting for completion
which should be avoided
- in case of multiple threads waiting, the complete() call in interrupt
will signal only one waiting thread per interrupt which may lead to
timeout for the others
- in case of channel status get as the CSC interrupt is not refcounted
ISR may disable interrupt for threads that were just enabled it.
To solve these the access to controls were protected by a mutex. Along
with this there is no need for spinlock to protect the software cache
reads/updates b/w controls and ISR as the update is happening only when
requested from control, and only one reader can reach the control.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-4-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
wait_for_completion_interruptible_timeout() returns 0 in case of
timeout. Check this into account when returning from function.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-3-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPDIFRX block is clocked by 2 clocks: peripheral and generic clocks.
Peripheral clock feeds user interface (registers) and generic clock feeds
the receiver.
To enable the receiver the generic clock needs to be enabled and also the
ENABLE bit of MCHP_SPDIFRX_MR register need to be set.
The signal control exported by mchp-spdifrx driver reports wrong status
when the receiver is disabled. This can happen when requesting the signal
and the capture was not previously started. To solve this the receiver
needs to be enabled (by enabling generic clock and setting ENABLE bit of
MR register) before reading the signal status.
As with this fix there are 2 paths now that need to control the generic
clock and ENABLE bit of SPDIFRX_MR register (one path though controls, one
path though configuration) a mutex has been introduced. We can't rely on
subsystem locking as the controls are protected by
struct snd_card::controls_rwsem semaphore and configuration is protected
by a different lock (embedded in snd_pcm_stream_lock_irq()).
The introduction of mutex is also extended to other controls which rely on
SPDIFRX_RSR.ULOCK bit as it has been discovered experimentally that having
both clocks enabled but not the receiver (through ENABLE bit of SPDIFRX.MR)
leads to inconsistent values of SPDIFRX_RSR.ULOCK. Thus on some controls we
rely on software state (dev->trigger_enabled protected by mutex) to
retrieve proper values.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-2-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Claudiu Beznea <claudiu.beznea@microchip.com>:
The following series adds runtime PM and suspend to RAM features for
mchp-pdmc driver.
Along with it 2 cleanup patches were added:
- patch 1/4: use vendor,device.yaml file format for Microchip AT91 ASoC
bindings
- patch 4/4: use FIELD_PREP() in mchp-spdiftx.c
Add support for suspend to RAM by re-aranging the lines in switch..case
from mchp_pdmc_trigger() and saving/restoring the enabled interrupts. These
are necessary as AT91 devices has a special power saving mode (called
backup and self-refresh) where most of the SoC parts are powered off
and thus we need to reconfigure the PDMC on resume.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221213112851.89212-4-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement clock power saving taking advantage of runtime PM infrastructure.
This simplifies the code and allow using the same infrastructure for
suspend to RAM functionalities.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221213112851.89212-3-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A remove callback just returning 0 is equivalent to no remove callback
at all. So drop the useless function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221212205406.3771071-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
A remove callback just returning 0 is equivalent to no remove callback
at all. So drop the useless function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221212205406.3771071-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for system suspend/resume by moving the enable/disable
of interrupts in mchp_spdiftx_trigger() on SNDRV_PCM_TRIGGER_SUSPEND/
SNDRV_PCM_TRIGGER_RESUME commands.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221117123750.291911-4-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add runtime PM support for Microchip SPDIFTX driver. The runtime PM
APIs disables/enables IP's clock and enables/disable caching for
regmap.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221117123750.291911-3-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a temporary variable to keep the AES3 value. With this a
spin_unlock_irqrestore() call has been removed from the final code.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221117123750.291911-2-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Return the value from asoc_ssc_init() directly instead of storing it
in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220823075335.209072-1-ye.xingchen@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
A recent change in clang strengthened its -Wbitfield-constant-conversion
to warn when 1 is assigned to a 1-bit signed integer bitfield, as it can
only be 0 or -1, not 1:
sound/soc/atmel/mchp-spdiftx.c:505:20: error: implicit truncation from 'int' to bit-field changes value from 1 to -1 [-Werror,-Wbitfield-constant-conversion]
dev->gclk_enabled = 1;
^ ~
1 error generated.
The actual value of the field is never checked, just that it is not
zero, so there is not a real bug here. However, it is simple enough to
silence the warning by making the bitfield unsigned, which matches the
mchp-spdifrx driver.
Fixes: 06ca24e98e ("ASoC: mchp-spdiftx: add driver for S/PDIF TX Controller")
Link: https://github.com/ClangBuiltLinux/linux/issues/1686
Link: 82afc9b169
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20220810010809.2024482-1-nathan@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Claudiu Beznea <claudiu.beznea@microchip.com>:
Hi,
The series adds one fix for mchp-spdifrx and one cleanups for
mchp-spdifrx and mchp-spdifrx drivers.
Thank you,
Claudiu Beznea
Changes in v3:
- changed cover letter title s/few/one, s/cleanups/cleanup
- fix compilation error and warnings
- keep only patch 1/5 and patch 3/5 from previous version as the rest
of them were integrated
Changes in v2:
- s/tag/tab in the title of patch 2/5
Claudiu Beznea (2):
ASoC: mchp-spdifrx: disable end of block interrupt on failures
ASoC: mchp-spdiftx: remove references to mchp_i2s_caps
sound/soc/atmel/mchp-spdifrx.c | 9 ++++++---
sound/soc/atmel/mchp-spdiftx.c | 8 --------
2 files changed, 6 insertions(+), 11 deletions(-)
--
2.34.1
Disable end of block interrupt in case of wait for completion timeout
or errors to undo previously enable operation (done in
mchp_spdifrx_isr_blockend_en()). Otherwise we can end up with an
unbalanced reference counter for this interrupt.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220727090814.2446111-2-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Claudiu Beznea <claudiu.beznea@microchip.com>:
The series adds one fix for mchp-spdifrx and few cleanups for
mchp-spdifrx and mchp-spdifrx drivers.
Avoid having patterns like:
int ret;
// ...
ret = 0;
// ...
ret = call_function();
if (ret)
return ret;
return 0;
and return directly ret for all cases.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220725130925.1781791-5-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the legacy DAI naming flag from opting in to the new scheme
(non_legacy_dai_naming), to opting out of it (legacy_dai_naming).
These drivers appear to be on the CPU side of the DAI link and
currently uses the legacy naming, so add the new flag.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623125250.2355471-20-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function snd_soc_unregister_card() returned 0 unconditionally and most
callers don't care to check the return value. Make it return void and
adapt the callers that didn't ignore the return value before.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220621145834.198519-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Now the core has been migrated across to the new direct clock
specification we can move the drivers back to the normal set_fmt
callback.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220519154318.2153729-31-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of updating the core to directly tell drivers if they are clock
provider or consumer update these CPU side drivers to use the new direct
callback.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220519154318.2153729-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>:
Before componentisation any part registered as a CODEC would have
automatically supported both little and big endian, ie. the core
would duplicate any supported LE or BE PCM format to support the other
endian as well. As componentisation removed the distinction between
CODEC drivers and platform drivers, a flag was added to specify
if this behaviour is required for a particular component. However,
as most systems tend to use little endian the absence of the flag
is rarely noticed. Also the naming of the flag "endianness" is a
little unobvious as to if it should be applied to a particular
component.
This series adds a comment to better explain the meaning of the
flag and then tidys up the usage of the flag. A couple of uses
of the flag are removed where is has been used inappropriately
on the CPU side of the DAI link, this is clearly not valid in the
cases it has been used, and I suspect never would be valid. Then
some redundant formats are removed, since they would be covered by
existing endianness flags. And finally a bunch of devices that are
missing the flag have it added.
It is worth noting that since componenisation there are now a couple
of cases where it is not entire clear to me that the flag should
be applied to all CODECs as it was before. In those cases I haven't
updated the driver to add the flag and they are outlined here:
1) Build into the AP CODECs, these are actual silicon inside the main
processor and they typically receive audio directly from an internal
bus. It is not obvious to me that these can happily ignore endian. On
the CODEC side these include: jz4725b.c, jz4760.c, jz4770.c,
rk3328_codec.c, lpass-va-macro.c, lpass-rx-macro.c, lpass-tx-macro.c,
lpass-wsa-macro.c. There are also some examples of this scattered
around the various platform support directories in sound/soc.
2) Devices behind non-audio buses, SPI just moves bits and doesn't
really define an endian for audio data on the bus. Thus it seems the
CODEC probably can care about the endian. The only devices that fall
into this group (mostly for AoV) are: rt5514-spi.c, rt5677-spi.c,
cros_ec_codec.c (only the AoV).
3) CODECs with no DAIs, these could specify the flag and plenty of
them do; CODECs from the initial conversion to componentisation. But
the flag makes no difference here since there is nothing for it to
apply to. This includes purely analogue CODECs: aw8738.c, ssm2305.c,
tpa6130a2.c, tda7419.c, max9759.c, max9768.c, max9877.c, lm4857.c,
simple-mux.c, simple-amplifier.c. And devices that only do jack
detection: ts3a227e.c, mt6359-accdet.c.
If there are any opinions on adding the flag to any of those three
groups they would be greatfully received. But I am leaning towards
leaving 1,2 without endianness flags since it feels inappropriate,
and removing the endian flag from devices in catagory 3 that already
have it. Assuming no one objects to that I will do a follow up
series for that.
Log the error code when snd_soc_regster_card() fails, but fold in the
silencing of deferred probe errors.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220506130349.451452-1-broonie@kernel.org
The endianness flag should have been removed when the driver was
ported across from having both a CODEC and CPU side component, to
just having a CPU component and using the dummy for the CODEC. The
endianness flag is used to indicate that the device is completely
ambivalent to the endianness of the data, typically due to the
endianness being lost over the hardware link (ie. the link defines
bit ordering). It's usage didn't have any effect when the driver
had both a CPU and CODEC component, since the union of those equals
the CPU side settings, but now causes the driver to falsely report
it supports big endian. Correct this by removing the flag.
Fixes: 1dfdbe73cc ("ASoC: atmel-classd: remove codec component")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220504170905.332415-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The endianness flag should have been removed when the driver was
ported across from having both a CODEC and CPU side component, to
just having a CPU component and using the dummy for the CODEC. The
endianness flag is used to indicate that the device is completely
ambivalent to the endianness of the data, typically due to the
endianness being lost over the hardware link (ie. the link defines
bit ordering). It's usage didn't have any effect when the driver
had both a CPU and CODEC component, since the union of those equals
the CPU side settings, but now causes the driver to falsely report
it supports big endian. Correct this by removing the flag.
Fixes: f3c668074a ("ASoC: atmel-pdmic: remove codec component")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220504170905.332415-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since a pointer to struct snd_dmaengine_pcm_config is passed,
snd_dmaengine_pcm_prepare_slave_config() is no longer called unless it's
explicitly set in prepare_slave_config.
Fixes: 50291652af ("ASoC: atmel: mchp-pdmc: add PDMC driver")
Suggested-by: Sascha Hauer <sha@pengutronix.de>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220421125403.2180824-2-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Mark Brown <broonie@kernel.org>:
This series contains a bunch of fairly minor changes which overhaul and
modernise the WM8731 driver, there should be no impact on the driver's
functionality.
The AT91SAM9G20-EK audio driver is replacing any error code returned by
atmel_ssc_set_audio() with -EINVAL which could be unhelpful for debugging.
Pass through the error code, and include it in the log message we print for
good measure.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220325154241.1600757-4-broonie@kernel.org
The error handling in the AT91SAM9G20-EK machine driver probe did not
consistently free the SSC in error paths, sometimes immediately returning
an error rather than doing cleanup. Fix this.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220325154241.1600757-3-broonie@kernel.org
The MCLK of the WM8731 on the AT91SAM9G20-EK board is connected to the
PCK0 output of the SoC, intended in the reference software to be supplied
using PLLB and programmed to 12MHz. As originally written for use with a
board file the audio driver was responsible for configuring the entire tree
but in the conversion to the common clock framework the registration of
the named pck0 and pllb clocks was removed so the driver has failed to
instantiate ever since.
Since the WM8731 driver has had support for managing a MCLK provided via
the common clock framework for some time we can simply drop all the clock
management code from the machine driver other than configuration of the
sysclk rate, the CODEC driver still respects that configuration from the
machine driver.
Fixes: ff78a189b0 ("ARM: at91: remove old at91-specific clock driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220325154241.1600757-2-broonie@kernel.org
Placing both the I2C and SPI code in the same module causes problems with
mixes of modular and non-modular builds of the buses so it's generally bad
practice. As with other drivers split the bus code out of the WM8731 driver
into separate modules.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220325153121.1598494-6-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The correct property is 'microchip,mic-pos', not 'mchp,mic-pos', so
replace all occurences of 'mchp,mic-pos' with 'microchip,mic-pos'.
Fix a multi-line comment format while we are at it.
Fixes: 50291652af ("ASoC: atmel: mchp-pdmc: add PDMC driver")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220318092609.130901-1-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
This function only calls of_node_put() in the regular path.
And it will cause refcount leak in error path.
Fixes: fdbcb3cba5 ("ASoC: atmel: machine driver for at91sam9x5-wm8731 boards")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220316111530.4551-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In function mchp_pdmc_af_put(), Intel's kernel test robot reports the
following warning:
sound/soc/atmel/mchp-pdmc.c:186:34: warning: address of array \
'uvalue->value.integer.value' will always evaluate to 'true' \
[-Wpointer-bool-conversion]
This is because we are using `uvalue->value.integer.value` which its
type is `long value[128];` for conditional expression and that array
will always decay to a non-NULL pointer. Using a non-NULL pointer for
conditional expression will always evaluate to true.
Fix this by changing it to `uvalue->value.integer.value[0]` as that's
what the mchp_pdmc_af_get() function sets.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alviro Iskandar Setiawan <alviro.iskandar@gnuweeb.org>
Link: https://lore.kernel.org/r/20220315001848.3763534-1-alviro.iskandar@gnuweeb.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a spelling mistake in a dev_info message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220309164116.178685-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The print function dev_err() is redundant because
platform_get_irq() already prints an error.
Eliminate the follow coccicheck warning:
./sound/soc/atmel/mchp-pdmc.c:991:2-9: line 991 is redundant because
platform_get_irq() already prints an error.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220310082756.1183-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Codrin Ciubotariu <codrin.ciubotariu@microchip.com>:
This patch series adds support for Pulse Density Microphone Controller
(PDMC), present on Microchip's SAMA7G5.
The PDMC interfaces up to 4 digital microphones having Pulse Density
Modulated (PDM) outputs. It generates a single clock line and samples 1 or
2 data lines. The signal path includes an audio grade programmable
decimation filter and outputs 24-bit audio words.
The source of each channel can be independently defined as PDMC_DS0 or
PDMC_DS1, sampled at the rising or falling edge of PDMC_CLK.
The patch series starts with a fix on the ASoC DMA engine support. Then
continues with the bindings and the driver of PDMC. It is followed by the
DT nodes for SAMA7G5 and SAMA7G5-EK. In the end, the drivers for PDMC
and PDM microphones are enabled in sama7_defconfig.
The Pulse Density Microphone Controller (PDMC) interfaces up to 4 digital
microphones having Pulse Density Modulated (PDM) outputs. It generates a
single clock line and samples 1 or 2 data lines. The signal path includes
an audio grade programmable decimation filter and outputs 24-bit audio
words on the APB bus.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220307122202.2251639-4-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
This function only calls of_node_put() in the regular path.
And it will cause refcount leak in error paths.
Fix this by calling of_node_put() in error handling too.
Fixes: a45f8853a5 ("ASoC: Add driver for PROTO Audio CODEC (with a WM8731)")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220308013949.20323-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This node pointer is returned by of_parse_phandle() with refcount
incremented in this function.
Calling of_node_put() to avoid the refcount leak.
Fixes: 531f67e41d ("ASoC: at91sam9g20ek-wm8731: convert to dt support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220307124539.1743-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the potential failure of the clk_enable(),
it should be better to check it and return error if fals.
Fixes: cbaadf0f90 ("ASoC: atmel_ssc_dai: refactor the startup and shutdown")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220301090637.3776558-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the Atmel drivers to use the new style defines for clocking in DAI
formats.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
This patch switch to use snd_soc_daifmt_parse_format/clock_provider() from
snd_soc_of_parse_daifmt().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/875yyhw9e8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For both capture and playback streams to work at the same time, only the
needed values from a register need to be updated. Also, clocks should be
enabled only when the first stream is started and stopped when there is no
running stream.
Fixes: b543e467d1 ("ASoC: atmel-i2s: add driver for the new Atmel I2S controller")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20210618150741.401739-2-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2S needs to have the same sample bits for both capture and playback
streams.
Fixes: b543e467d1 ("ASoC: atmel-i2s: add driver for the new Atmel I2S controller")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20210618150741.401739-1-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S-MCC found on SAMA7G5 includes 2 FIFOs (capture and playback). When
FIFOs are enabled, bits I2SMCC_ISRA.TXLRDYx and I2SMCC_ISRA.TXRRDYx must
not be used. Bits I2SMCC_ISRB.TXFFRDY and I2SMCC_ISRB.RXFFRDY must be used
instead.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20210301170905.835091-7-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SAMA7G5's I2S-MCC has 4 pairs of DIN/DOUT pins. Since TDM only uses a
single pair of pins for synchronous capture and playback, the controller
needs to be told which of the pair is connected. This can be mentioned
using the "microchip,tdm-data-pair" property from DT. The property is
optional, useful only if TDM is used. If it's missing, DIN/DOUT 0 pins
will be used by default.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20210301170905.835091-6-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The latest I2S-MCC available in SAMA7G5 supports multi-channel for I2S and
Left-Justified formats. For this, the new version uses 8 (4 * 2) input and
output pins, with each pin being responsible for 2 channels. This sums up
to a total of 8 channels for synchronous capture and playback.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20210301170905.835091-4-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Microchip's new SAMA7G5 includes an updated I2S-MCC compatible with the
previous version found on SAM9X60. The new controller includes 8 (4 * 2)
input and output data pins for up to 8 channels for I2S and Left-Justified
formats.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20210301170905.835091-3-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of manually managing its DMA buffers using
dma_{alloc,free}_coherent() lets the sound core take care of this using
managed buffers.
On one hand this reduces the amount of boiler plate code, but the main
motivation for the change is to use the shared code where possible. This
makes it easier to argue about correctness and that the code does not
contain subtle bugs like data leakage or similar.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20210106133650.13509-1-lars@metafoo.de
Signed-off-by: Mark Brown <broonie@kernel.org>
There are a couple of spelling mistakes in the Kconfig help text. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20201216112608.11385-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Compile-testing this driver on an older platform without CONFIG_COMMON_CLK fails with
ERROR: modpost: "clk_set_min_rate" [sound/soc/atmel/snd-soc-mchp-spdifrx.ko] undefined!
Make this is a strict dependency.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20201203223815.1353451-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The Validity bits (bit 28) must not be set in order to have the samples
valid. Some controllers look for this bit and ignore the samples if it
is set.
Fixes: 06ca24e98e ("ASoC: mchp-spdiftx: add driver for S/PDIF TX Controller")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20201104155738.68403-1-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Besides the fact that muxclk is optional, muxclk can be set using
assigned-clocks, removing the need to set it in driver. The warning is
thus unneeded, so we can transform it in a debug print, eventually to just
reflect that muxclk was not set by the driver.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20201103100554.1307190-1-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a spelling mistake in a dev_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20201006152024.542418-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The new SPDIF RX controller is a serial port compliant with the IEC-60958
standard. It also supports programmable User Data and Channel Status
fields.
This IP is embedded in Microchip's sama7g5 SoC.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20201002160305.815523-3-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 95e0e07e71 ("ASoC: atmel-pcm: use generic dmaengine
framework"), the driver is using dmaengine and is not using any definition
from include/linux/platform_data/dma-atmel.h, stop including it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200930145330.3043528-1-alexandre.belloni@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The new SPDIF TX controller is a serial port compliant with the IEC-
60958 standard. It also supports programmable User Data and Channel
Status fields.
This IP is embedded in Microchip's sama7g5 SoC.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20200909145348.367033-2-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
-
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/87eepb2dnq.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CPU and the codec both are represented now as components, so for
PDMIC we are registering two componenets with the same name. Since
there is no actual codec, we will merge the codec component into the
CPU one and use a dummy codec instead, for the DAI link.
As a bonus, debugfs will no longer report an error when will try to
create entries for both componenets with the same name.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20200708163359.2698696-1-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
