Add new interrupt handle callbacks in acp_common_hw_ops.
Refactor and move interrupt handler registration form platform
driver to pci driver.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://patch.msgid.link/20250310183201.11979-7-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add page table entry configurations to support higher sample rate
streams with multiple channels for ACP7.0 platforms.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://patch.msgid.link/20240903113427.182997-11-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All I2S instances are connected to different powertile form acp6.0
onwards, refactor dai driver to support all I2S instances for all acp
platforms.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://patch.msgid.link/20240903113427.182997-3-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP pin configuration varies based on acp version.
ACP PCI driver should read the ACP PIN config value and based on config
value, it has to create a platform device in below two conditions.
1) If ACP PDM configuration is selected from BIOS and ACP PDM controller
exists.
2) If ACP I2S configuration is selected from BIOS.
Other than above scenarios, ACP PCI driver should skip the platform
device creation logic, i.e. ACP PCI driver probe sequence should never
fail if other acp pin configuration is selected. It should skip platform
device creation logic.
check_acp_pdm() function was implemented for ACP6.x platforms to check
ACP PDM configuration. Previously, this code was safe guarded by
FLAG_AMD_LEGACY_ONLY_DMIC flag check.
This implementation breaks audio use cases for Huawei Matebooks which are
based on ACP3.x varaint uses I2S configuration.
In current scenario, check_acp_pdm() function returns -ENODEV value
which results in ACP PCI driver probe failure without creating a platform
device even in case of valid ACP pin configuration.
Implement check_acp_config() as a common function which invokes platform
specific acp pin configuration check functions for ACP3.x, ACP6.0 & ACP6.3
& ACP7.0 variants and checks for ACP PDM controller.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218780
Fixes: 4af565de9f ("ASoC: amd: acp: fix for acp pdm configuration check")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20240502140340.4049021-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add i2s and dmic support for Rembrandt platform,
Add machine support for nau8825, max98360 and rt5682s,rt1019 codec
in legacy driver for rembrandt platform.
Here codec is in a slave mode.
Signed-off-by: V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com>
Link: https://lore.kernel.org/r/20220707161142.491034-4-Vsujithkumar.Reddy@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ADD Generic code to support to newer platforms, add
control threshold, irq control macros ,added structure for register
offset differences.
Signed-off-by: V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com>
Link: https://lore.kernel.org/r/20220707161142.491034-3-Vsujithkumar.Reddy@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP hardware has PGFSM control registers that can be configured to
power On/Off the ACP IP block. Add acp init()/de_init() callbacks
in renoir platform driver probe()/remove() respectively to power
on and off ACP IP block on ACP3X device.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Link: https://lore.kernel.org/r/20220117115854.455995-5-AjitKumar.Pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver module for PDM controller on ACP IP block. Expose dai
ops to configure ACP_WOV_PDM_BLOCK registers on ACP. Such dai ops
will be used by platform specific driver module to register dmic
related dai with ASoC.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Link: https://lore.kernel.org/r/20220117115854.455995-2-AjitKumar.Pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We are using legacy way of exposing dais and DMA configuration that
requires separate driver modules for various ACP SOC with almost
similar hw configuration. Moreover the legacy approach requires
separate I2S and DMA module platform devices registration and need
machine specific quirk to control various I2S endpoints. Add generic
dai driver and platform driver for I2S controller on ACP hw block.
This common framework can be used by various ACP platform devices
that shares common specs.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Link: https://lore.kernel.org/r/20211019070938.5076-2-AjitKumar.Pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
