DualPI2 provides L4S-type low latency & loss to traffic that uses a
scalable congestion controller (e.g. TCP-Prague, DCTCP) without
degrading the performance of 'classic' traffic (e.g. Reno,
Cubic etc.). It is to be the reference implementation of IETF RFC9332
DualQ Coupled AQM (https://datatracker.ietf.org/doc/html/rfc9332).
Note that creating two independent queues cannot meet the goal of
DualPI2 mentioned in RFC9332: "...to preserve fairness between
ECN-capable and non-ECN-capable traffic." Further, it could even
lead to starvation of Classic traffic, which is also inconsistent
with the requirements in RFC9332: "...although priority MUST be
bounded in order not to starve Classic traffic." DualPI2 is
designed to maintain approximate per-flow fairness on L-queue and
C-queue by forming a single qdisc using the coupling factor and
scheduler between two queues.
The qdisc provides two queues called low latency and classic. It
classifies packets based on the ECN field in the IP headers. By
default it directs non-ECN and ECT(0) into the classic queue and
ECT(1) and CE into the low latency queue, as per the IETF spec.
Each queue runs its own AQM:
* The classic AQM is called PI2, which is similar to the PIE AQM but
more responsive and simpler. Classic traffic requires a decent
target queue (default 15ms for Internet deployment) to fully
utilize the link and to avoid high drop rates.
* The low latency AQM is, by default, a very shallow ECN marking
threshold (1ms) similar to that used for DCTCP.
The DualQ isolates the low queuing delay of the Low Latency queue
from the larger delay of the 'Classic' queue. However, from a
bandwidth perspective, flows in either queue will share out the link
capacity as if there was just a single queue. This bandwidth pooling
effect is achieved by coupling together the drop and ECN-marking
probabilities of the two AQMs.
The PI2 AQM has two main parameters in addition to its target delay.
The integral gain factor alpha is used to slowly correct any persistent
standing queue error from the target delay, while the proportional gain
factor beta is used to quickly compensate for queue changes (growth or
shrinkage). Either alpha and beta are given as a parameter, or they can
be calculated by tc from alternative typical and maximum RTT parameters.
Internally, the output of a linear Proportional Integral (PI)
controller is used for both queues. This output is squared to
calculate the drop or ECN-marking probability of the classic queue.
This counterbalances the square-root rate equation of Reno/Cubic,
which is the trick that balances flow rates across the queues. For
the ECN-marking probability of the low latency queue, the output of
the base AQM is multiplied by a coupling factor. This determines the
balance between the flow rates in each queue. The default setting
makes the flow rates roughly equal, which should be generally
applicable.
If DUALPI2 AQM has detected overload (due to excessive non-responsive
traffic in either queue), it will switch to signaling congestion
solely using drop, irrespective of the ECN field. Alternatively, it
can be configured to limit the drop probability and let the queue
grow and eventually overflow (like tail-drop).
GSO splitting in DUALPI2 is configurable from userspace while the
default behavior is to split gso. When running DUALPI2 at unshaped
10gigE with 4 download streams test, splitting gso apart results in
halving the latency with no loss in throughput:
Summary of tcp_4down run 'no_split_gso':
avg median # data pts
Ping (ms) ICMP : 0.53 0.30 ms 350
TCP download avg : 2326.86 N/A Mbits/s 350
TCP download sum : 9307.42 N/A Mbits/s 350
TCP download::1 : 2672.99 2568.73 Mbits/s 350
TCP download::2 : 2586.96 2570.51 Mbits/s 350
TCP download::3 : 1786.26 1798.82 Mbits/s 350
TCP download::4 : 2261.21 2309.49 Mbits/s 350
Summart of tcp_4down run 'split_gso':
avg median # data pts
Ping (ms) ICMP : 0.22 0.23 ms 350
TCP download avg : 2335.02 N/A Mbits/s 350
TCP download sum : 9340.09 N/A Mbits/s 350
TCP download::1 : 2335.30 2334.22 Mbits/s 350
TCP download::2 : 2334.72 2334.20 Mbits/s 350
TCP download::3 : 2335.28 2334.58 Mbits/s 350
TCP download::4 : 2334.79 2334.39 Mbits/s 350
A similar result is observed when running DUALPI2 at unshaped 1gigE
with 1 download stream test:
Summary of tcp_1down run 'no_split_gso':
avg median # data pts
Ping (ms) ICMP : 1.13 1.25 ms 350
TCP download : 941.41 941.46 Mbits/s 350
Summart of tcp_1down run 'split_gso':
avg median # data pts
Ping (ms) ICMP : 0.51 0.55 ms 350
TCP download : 941.41 941.45 Mbits/s 350
Additional details can be found in the draft:
https://datatracker.ietf.org/doc/html/rfc9332
Signed-off-by: Koen De Schepper <koen.de_schepper@nokia-bell-labs.com>
Co-developed-by: Olga Albisser <olga@albisser.org>
Signed-off-by: Olga Albisser <olga@albisser.org>
Co-developed-by: Olivier Tilmans <olivier.tilmans@nokia.com>
Signed-off-by: Olivier Tilmans <olivier.tilmans@nokia.com>
Co-developed-by: Henrik Steen <henrist@henrist.net>
Signed-off-by: Henrik Steen <henrist@henrist.net>
Co-developed-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Signed-off-by: Bob Briscoe <research@bobbriscoe.net>
Signed-off-by: Ilpo Järvinen <ij@kernel.org>
Acked-by: Dave Taht <dave.taht@gmail.com>
Link: https://patch.msgid.link/20250722095915.24485-4-chia-yu.chang@nokia-bell-labs.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The configuration and statistics dump of the DualPI2 Qdisc provides
information related to both queues, such as packet numbers and queuing
delays in the L-queue and C-queue, as well as general information such as
probability value, WRR credits, memory usage, packet marking counters, max
queue size, etc.
The following patch includes enqueue/dequeue for DualPI2.
Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Link: https://patch.msgid.link/20250722095915.24485-3-chia-yu.chang@nokia-bell-labs.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DualPI2 is the reference implementation of IETF RFC9332 DualQ Coupled
AQM (https://datatracker.ietf.org/doc/html/rfc9332) providing two
queues called low latency (L-queue) and classic (C-queue). By default,
it enqueues non-ECN and ECT(0) packets into the C-queue and ECT(1) and
CE packets into the low latency queue (L-queue), as per IETF RFC9332 spec.
This patch defines the dualpi2 Qdisc structure and parsing, and the
following two patches include dumping and enqueue/dequeue for the DualPI2.
Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Link: https://patch.msgid.link/20250722095915.24485-2-chia-yu.chang@nokia-bell-labs.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, BIS_LINK is used for both BIG sync and PA sync connections,
which makes it impossible to distinguish them when searching for a PA
sync connection.
Adding PA_LINK will make the distinction clearer and simplify future
extensions for PA-related features.
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The Event_Type field in an LE Extended Advertising Report uses bits 5
and 6 for data status (e.g. truncation or fragmentation), not the PDU
type itself.
The ext_evt_type_to_legacy() function fails to mask these status bits
before evaluation. This causes valid advertisements with status bits set
(e.g. a truncated non-connectable advertisement, which ends up showing
as PDU type 0x40) to be misclassified as unknown and subsequently
dropped. This is okay for most checks which use bitwise AND on the
relevant event type bits, but it doesn't work for non-connectable types,
which are checked with '== LE_EXT_ADV_NON_CONN_IND' (that is, zero).
In terms of behaviour, first the device sends a truncated report:
> HCI Event: LE Meta Event (0x3e) plen 26
LE Extended Advertising Report (0x0d)
Entry 0
Event type: 0x0040
Data status: Incomplete, data truncated, no more to come
Address type: Random (0x01)
Address: 1D:12:46:FA:F8:6E (Non-Resolvable)
SID: 0x03
RSSI: -98 dBm (0x9e)
Data length: 0x00
Then, a few seconds later, it sends the subsequent complete report:
> HCI Event: LE Meta Event (0x3e) plen 122
LE Extended Advertising Report (0x0d)
Entry 0
Event type: 0x0000
Data status: Complete
Address type: Random (0x01)
Address: 1D:12:46:FA:F8:6E (Non-Resolvable)
SID: 0x03
RSSI: -97 dBm (0x9f)
Data length: 0x60
Service Data: Google (0xfef3)
Data[92]: ...
These devices often send multiple truncated reports per second.
This patch introduces a PDU type mask to ensure only the relevant bits
are evaluated, allowing for the correct translation of all valid
extended advertising packets.
Fixes: b2cc9761f1 ("Bluetooth: Handle extended ADV PDU types")
Signed-off-by: Chris Down <chris@chrisdown.name>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Currently both dev_coredumpv and skb_put_data in hci_devcd_dump use
hdev->dump.head. However, dev_coredumpv can free the buffer. From
dev_coredumpm_timeout documentation, which is used by dev_coredumpv:
> Creates a new device coredump for the given device. If a previous one hasn't
> been read yet, the new coredump is discarded. The data lifetime is determined
> by the device coredump framework and when it is no longer needed the @free
> function will be called to free the data.
If the data has not been read by the userspace yet, dev_coredumpv will
discard new buffer, freeing hdev->dump.head. This leads to
vmalloc-out-of-bounds error when skb_put_data tries to access
hdev->dump.head.
A crash report from syzbot illustrates this:
==================================================================
BUG: KASAN: vmalloc-out-of-bounds in skb_put_data
include/linux/skbuff.h:2752 [inline]
BUG: KASAN: vmalloc-out-of-bounds in hci_devcd_dump+0x142/0x240
net/bluetooth/coredump.c:258
Read of size 140 at addr ffffc90004ed5000 by task kworker/u9:2/5844
CPU: 1 UID: 0 PID: 5844 Comm: kworker/u9:2 Not tainted
6.14.0-syzkaller-10892-g4e82c87058f4 #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 02/12/2025
Workqueue: hci0 hci_devcd_timeout
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:408 [inline]
print_report+0xc3/0x670 mm/kasan/report.c:521
kasan_report+0xe0/0x110 mm/kasan/report.c:634
check_region_inline mm/kasan/generic.c:183 [inline]
kasan_check_range+0xef/0x1a0 mm/kasan/generic.c:189
__asan_memcpy+0x23/0x60 mm/kasan/shadow.c:105
skb_put_data include/linux/skbuff.h:2752 [inline]
hci_devcd_dump+0x142/0x240 net/bluetooth/coredump.c:258
hci_devcd_timeout+0xb5/0x2e0 net/bluetooth/coredump.c:413
process_one_work+0x9cc/0x1b70 kernel/workqueue.c:3238
process_scheduled_works kernel/workqueue.c:3319 [inline]
worker_thread+0x6c8/0xf10 kernel/workqueue.c:3400
kthread+0x3c2/0x780 kernel/kthread.c:464
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:153
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
The buggy address ffffc90004ed5000 belongs to a vmalloc virtual mapping
Memory state around the buggy address:
ffffc90004ed4f00: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
ffffc90004ed4f80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
>ffffc90004ed5000: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
^
ffffc90004ed5080: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
ffffc90004ed5100: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
==================================================================
To avoid this issue, reorder dev_coredumpv to be called after
skb_put_data that does not free the data.
Reported-by: syzbot+ac3c79181f6aecc5120c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ac3c79181f6aecc5120c
Fixes: b257e02ecc ("HCI: coredump: Log devcd dumps into the monitor")
Tested-by: syzbot+ac3c79181f6aecc5120c@syzkaller.appspotmail.com
Signed-off-by: Ivan Pravdin <ipravdin.official@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
User-space applications (e.g. PipeWire) depend on
ISO-formatted timestamps for precise audio sync.
The ISO ts is based on the controller’s clock domain,
so hardware timestamping (hwtimestamp) must be used.
Ref: Documentation/networking/timestamping.rst,
section 3.1 Hardware Timestamping.
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
User applications need a way to track which ISO interval a given SDU
belongs to, to properly detect packet loss. All controllers do not set
timestamps, and it's not guaranteed user application receives all packet
reports (small socket buffer, or controller doesn't send all reports
like Intel AX210 is doing).
Add socket option BT_PKT_SEQNUM that enables reporting of received
packet ISO sequence number in BT_SCM_PKT_SEQNUM CMSG.
Use BT_PKT_SEQNUM == 22 for the socket option, as 21 was used earlier
for a removed experimental feature that never got into mainline.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Correct the misspelling of “estabilished” in the code.
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When the BIS source stops, the controller sends an LE BIG Sync Lost
event (subevent 0x1E). Currently, this event is not handled, causing
the BIS stream to remain active in BlueZ and preventing recovery.
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
HCI_EV_EXTENDED_INQUIRY_RESULT's comment wrongly uses 0x2d as its event
code.
Use right 0x2f instead.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Eliminate an unnecessary goto label by using break instead of goto to
exit the loop in hci_find_irk_by_addr().
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use bt_dev_err() instead of bt_dev_dbg() to log error message in
hci_update_event_filter_sync().
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reset cookie value to 0 instead of 0xffffffff in hci_sock_free_cookie()
since:
0 : means cookie has not been assigned yet
0xffffffff: means cookie assignment failure
Also fix generating cookie failure with usage shown below:
hci_sock_gen_cookie(sk) // generate cookie
hci_sock_free_cookie(sk) // free cookie
hci_sock_gen_cookie(sk) // Can't generate cookie any more
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On devices without WANT_MONITOR_VIF (and probably without
channel context support) we get a WARN_ON for changing the
per-link setting of a monitor interface.
Since we already skip AP_VLAN interfaces and MONITOR with
WANT_MONITOR_VIF and/or NO_VIRTUAL_MONITOR should update
the settings, catch this in the link change code instead
of the warning.
Reported-by: Martin Kaistra <martin.kaistra@linutronix.de>
Link: https://lore.kernel.org/r/a9de62a0-28f1-4981-84df-253489da74ed@linutronix.de/
Fixes: c4382d5ca1 ("wifi: mac80211: update the right link for tx power")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mentioned MIB is currently incremented even when a packet
with an old sequence number (i.e. a zero window probe) is received,
which is IMHO misleading.
Explicitly restrict such MIB increment at the relevant events.
Fixes: 6c758062c6 ("tcp: add LINUX_MIB_BEYOND_WINDOW")
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Link: https://patch.msgid.link/20d147292eb4b13b6535e0ad6f56be64d9c330d3.1753118029.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The nipa CI is reporting frequent failures in the mptcp_connect
self-tests.
In the failing scenarios (TCP -> MPTCP) the involved sockets are
actually plain TCP ones, as fallback for passive socket at 2whs
time cause the MPTCP listener to actually create a TCP socket.
The transfer is stuck due to the receiver buffer being zero.
With the stronger check in place, tcp_clamp_window() can be invoked
while the TCP socket has sk_rmem_alloc == 0, and the receive buffer
will be zeroed, too.
Check for the critical condition in tcp_prune_queue() and just
drop the packet without shrinking the receiver buffer.
Fixes: 1d2fbaad7c ("tcp: stronger sk_rcvbuf checks")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20c18165d3f848e1c5c1b782d88c1a5ab38b3f70.1753118029.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Background
==========
When TCP retransmits a packet due to missing ACKs, the
retransmission may fail for various reasons (e.g., packets
stuck in driver queues, receiver zero windows, or routing issues).
The original tcp_retransmit_skb tracepoint:
'commit e086101b15 ("tcp: add a tracepoint for tcp retransmission")'
lacks visibility into these failure causes, making production
diagnostics difficult.
Solution
========
Adds the retval("err") to the tcp_retransmit_skb tracepoint.
Enables users to know why some tcp retransmission failed and
users can filter retransmission failures by retval.
Compatibility description
=========================
This patch extends the tcp_retransmit_skb tracepoint
by adding a new "err" field at the end of its
existing structure (within TP_STRUCT__entry). The
compatibility implications are detailed as follows:
1) Structural compatibility for legacy user-space tools
Legacy tools/BPF programs accessing existing fields
(by offset or name) can still work without modification
or recompilation.The new field is appended to the end,
preserving original memory layout.
2) Note: semantic changes
The original tracepoint primarily only focused on
successfully retransmitted packets. With this patch,
the tracepoint now can figure out packets that may
terminate early due to specific reasons. For accurate
statistics, users should filter using "err" to
distinguish outcomes.
Before patched:
field:const void * skbaddr; offset:8; size:8; signed:0;
field:const void * skaddr; offset:16; size:8; signed:0;
field:int state; offset:24; size:4; signed:1;
field:__u16 sport; offset:28; size:2; signed:0;
field:__u16 dport; offset:30; size:2; signed:0;
field:__u16 family; offset:32; size:2; signed:0;
field:__u8 saddr[4]; offset:34; size:4; signed:0;
field:__u8 daddr[4]; offset:38; size:4; signed:0;
field:__u8 saddr_v6[16]; offset:42; size:16; signed:0;
field:__u8 daddr_v6[16]; offset:58; size:16; signed:0;
print fmt: "skbaddr=%p skaddr=%p family=%s sport=%hu dport=%hu saddr=%pI4 daddr=%pI4 saddrv6=%pI6c daddrv6=%pI6c state=%s"
After patched:
field:const void * skbaddr; offset:8; size:8; signed:0;
field:const void * skaddr; offset:16; size:8; signed:0;
field:int state; offset:24; size:4; signed:1;
field:__u16 sport; offset:28; size:2; signed:0;
field:__u16 dport; offset:30; size:2; signed:0;
field:__u16 family; offset:32; size:2; signed:0;
field:__u8 saddr[4]; offset:34; size:4; signed:0;
field:__u8 daddr[4]; offset:38; size:4; signed:0;
field:__u8 saddr_v6[16]; offset:42; size:16; signed:0;
field:__u8 daddr_v6[16]; offset:58; size:16; signed:0;
field:int err; offset:76; size:4; signed:1;
print fmt: "skbaddr=%p skaddr=%p family=%s sport=%hu dport=%hu saddr=%pI4 daddr=%pI4 saddrv6=%pI6c daddrv6=%pI6c state=%s err=%d"
Co-developed-by: xu xin <xu.xin16@zte.com.cn>
Signed-off-by: xu xin <xu.xin16@zte.com.cn>
Signed-off-by: Fan Yu <fan.yu9@zte.com.cn>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250721111607626_BDnIJB0ywk6FghN63bor@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add comments on endif & endmenu blocks. This can save time
when searching & trying to understand kconfig menu dependencies.
The other endif & endmenu statements are already commented like this.
This makes it similar to drivers/net/Kconfig, which is already
commented like this.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250721020420.3555128-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ieee80211_latest_active_link_conn_timeout() we loop over all
sta->links in order to compute the timeout expiring last across
all links.
Such timeout is stored in `latest_timeout` which is used in the
time_after() comparison before having been initialized.
Fix this behaviour by initializing the variable to `jiffies` and
adapt surrouding conditions accordingly.
Note that the caller assumed latest_timeout to be 0 if no active
link was found. This is not appropriate because jiffies=0 is a
valid (and recurrent, although not often) point in time.
By using `jiffies` as default value for latest_timeout, we can
fix the caller as well.
Address-Coverity-ID: 1647986 ("Uninitialized variables (UNINIT)")
Fixes: 1bc892d76a ("wifi: mac80211: extend connection monitoring for MLO")
Signed-off-by: Antonio Quartulli <antonio@mandelbit.com>
Link: https://patch.msgid.link/20250722120634.3501-1-antonio@mandelbit.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Warning: net/sunrpc/auth_gss/gss_krb5_crypto.c:902 function parameter
'len' not described in 'krb5_etm_decrypt'
Warning: net/sunrpc/auth_gss/gss_krb5_crypto.c:902 function parameter
'buf' not described in 'krb5_etm_decrypt'
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Extract common ip6gre tunnel match from ip6gre_tunnel_lookup() into new
helper function ip6gre_tunnel_match() to reduce code duplication.
No functional change intended.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250719081551.963670-1-yuehaibing@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
might_sleep could be trigger in the atomic context in qfq_delete_class.
qfq_destroy_class was moved into atomic context locked
by sch_tree_lock to avoid a race condition bug on
qfq_aggregate. However, might_sleep could be triggered by
qfq_destroy_class, which introduced sleeping in atomic context (path:
qfq_destroy_class->qdisc_put->__qdisc_destroy->lockdep_unregister_key
->might_sleep).
Considering the race is on the qfq_aggregate objects, keeping
qfq_rm_from_agg in the lock but moving the left part out can solve
this issue.
Fixes: 5e28d5a3f7 ("net/sched: sch_qfq: Fix race condition on qfq_aggregate")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Link: https://patch.msgid.link/4a04e0cc-a64b-44e7-9213-2880ed641d77@sabinyo.mountain
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/20250717230128.159766-1-xmei5@asu.edu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ieee80211_add_gtk_rekey receives a keyconf as an argument, and the
cipher and keylen are taken from there to the new allocated key.
But in rekey, both the cipher and the keylen should be the same as of
the old key, so let ieee80211_add_gtk_rekey find those, so drivers won't
have to fill it in.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250721214922.3c5c023bfae9.Ie6594ae2b4b6d5b3d536e642b349046ebfce7a5d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The processing of the struct cfg80211_sar_specs::sub_specs flexible
array requires its counter, num_sub_specs, to be assigned before the
loop in nl80211_set_sar_specs(). Leave the final assignment after the
loop in place in case fewer ended up in the array.
Fixes: aa4ec06c45 ("wifi: cfg80211: use __counted_by where appropriate")
Signed-off-by: Kees Cook <kees@kernel.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/20250721183125.work.183-kees@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While I caught the need for setting cnt early in nl80211_parse_rnr_elems()
in the original annotation of struct cfg80211_rnr_elems with __counted_by,
I missed a similar pattern in ieee80211_copy_rnr_beacon(). Fix this by
moving the cnt assignment to before the loop.
Fixes: 7b6d708703 ("wifi: cfg80211: Annotate struct cfg80211_rnr_elems with __counted_by")
Signed-off-by: Kees Cook <kees@kernel.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/20250721182521.work.540-kees@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement removing additional RSS contexts via Netlink.
Technically it'd be possible to shoehorn the delete operation
into ethnl_request_ops-compatible handler. The code ends
up longer than open coded version, and I think we'll need
a custom way of sending notifications at some stage (if we
allow tying the context lifetime to the netlink socket, in
the future).
Link: https://patch.msgid.link/20250717234343.2328602-8-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support creating contexts via Netlink. Setting flow hashing
fields on the new context is not supported at this stage,
it can be added later.
An empty indirection table is not supported. This is a carry
over from the IOCTL interface where empty indirection table
meant delete. We can repurpose empty indirection table in
Netlink but for now to avoid confusion reject it using the
policy.
Support letting user choose the ID for the new context. This was
not possible in IOCTL since the context ID field for the create
action had to be set to the ETH_RXFH_CONTEXT_ALLOC magic value.
Link: https://patch.msgid.link/20250717234343.2328602-7-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similarly to previous change, factor out populating the response.
We will use this after the context was allocated to send a notification
so this time factor out from the additional context handling, rather
than context 0 handling (for request context didn't exist, for response
it does).
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250717234343.2328602-5-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To ease the code reuse for RSS_CREATE we'll want to prepare
struct rss_reply_data for the new context. Unfortunately
we can't depend on the exiting scaffolding because the context
doesn't exist (ctx=NULL) when we start preparing. Factor out
the portion of the context 0 handling responsible for allocation
of request memory, so that we can call it directly.
Link: https://patch.msgid.link/20250717234343.2328602-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In anticipation for CREATE and DELETE notifications - explicitly
pass the notification type to ethtool_rss_notify(), when calling
from the IOCTL code.
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250717234343.2328602-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Supporting per-RSS context configuration of hashing fields but
not the hashing algorithm would complicate the code a lot.
We'd need to cross check the config against all RSS contexts.
None of the drivers need this today, so explicitly prevent
new drivers with such skewed capabilities from registering.
If such driver appears it will need to first adjust the checks
in the core.
Link: https://patch.msgid.link/20250717234343.2328602-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TCP_MAXSEG socket option is currently not supported by MPTCP, mainly
because it has never been requested before. But there are still valid
use-cases, e.g. with HAProxy.
This patch adds its support in MPTCP by propagating the value to all
subflows. The get part looks at the value on the first subflow, to be as
closed as possible to TCP. Only one value can be returned for the cached
MSS, so this can come only from one subflow.
Similar to mptcp_setsockopt_first_sf_only(), a generic helper
mptcp_setsockopt_all_subflows() is added to set sockopt for each
subflows of the mptcp socket.
Add a new member for struct mptcp_sock to store the TCP_MAXSEG value,
and return this value in getsockopt.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/515
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250719-net-next-mptcp-tcp_maxseg-v2-3-8c910fbc5307@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a helper tcp_sock_set_maxseg() to directly set the TCP_MAXSEG
sockopt from kernel space.
This new helper will be used in the following patch from MPTCP.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Acked-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250719-net-next-mptcp-tcp_maxseg-v2-2-8c910fbc5307@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcp_getsockopt() is called twice in mptcp_getsockopt_first_sf_only() in
different conditions, which makes the code a bit redundant.
The first call to tcp_getsockopt() when the first subflow exists can be
replaced by going to a new label "get" before the second call.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250719-net-next-mptcp-tcp_maxseg-v2-1-8c910fbc5307@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The upper layer may require the link ID to properly handle
unexpected frames. For instance, if hostapd, operating as an
AP MLD, receives a data frame from a non-associated STA,
it must send deauthentication to the link on which the STA is
operating.
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Reviewed-by: Money Wang <money.wang@mediatek.com>
Link: https://patch.msgid.link/20250721065159.1740992-1-michael-cy.lee@mediatek.com
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For broadcast frames, every interface might have to process it and
therefore the link_id cannot be determined in the driver.
In mac80211, when the frame is about to be forwarded to each interface,
we can use the member "freq" in struct ieee80211_rx_status to determine
the "link_id" for each interface.
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Reviewed-by: Money Wang <money.wang@mediatek.com>
Link: https://patch.msgid.link/20250721062929.1662700-1-michael-cy.lee@mediatek.com
[simplify, remove unnecessary link->conf check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmh9azkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG7GIH/0lpQtHRl6N+q2Qs
v75iG2ZouWyw2JlhUOHAToKU58MZqqTXLZzc8ZdY6fAd7DpXWKRGSDsyWVyLbUkt
UKGzXEIJsHXYvw2QIPbhkY9gQBWpdZTh4tHztFyKb0QLn81qkibVP6ChOwSzOGa/
xUyQ5v6yH+JvQlnQaCgy6hi7cMrLNSNZmuIjy0yc5Y153YPEtX5OUPO2PstpUx5r
AuiOhU4ewW9QCe07X/Pk7tdn0T2Jg8Kwk1FViaM0RBUf/0GXGfsovIxpUP/eCyMc
MA+9SXXLlDa/4Z8w3EsQYx6m2MnNmm0HPeevCmWqq3+Ocooik4si1BpzHfUaE6n/
/0D8zBg=
=NzEi
-----END PGP SIGNATURE-----
Merge tag 'v6.16-rc7' into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cc34acd577 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
netif_close_many is used only by vlan/dsa and one mtk driver, so move it into
NETDEV_INTERNAL namespace.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-8-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit cc34acd577 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
Note that one dev_set_threaded call still remains in mt76 for debugfs file.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-7-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit cc34acd577 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-6-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit cc34acd577 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
__netif_set_mtu is used only by bond, so move it into
NETDEV_INTERNAL namespace.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-5-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit cc34acd577 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
netif_pre_changeaddr_notify is used only by ipvlan/bond, so move it into
NETDEV_INTERNAL namespace.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-4-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit cc34acd577 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
netif_get_mac_address is used only by tun/tap, so move it into
NETDEV_INTERNAL namespace.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-3-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit cc34acd577 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-2-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Detect NICs and drivers that either drop frames with a corrupted TCP
checksum or, worse, pass them up as valid. The test flips one bit in
the checksum, transmits the packet in internal loopback, and fails when
the driver reports CHECKSUM_UNNECESSARY.
Discussed at:
https://lore.kernel.org/all/20250625132117.1b3264e8@kernel.org/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250717083524.1645069-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a new SKB drop reason (SKB_DROP_REASON_PFMEMALLOC) to track packets
dropped due to memory pressure. In production environments, we've observed
memory exhaustion reported by memory layer stack traces, but these drops
were not properly tracked in the SKB drop reason infrastructure.
While most network code paths now properly report pfmemalloc drops, some
protocol-specific socket implementations still use sk_filter() without
drop reason tracking:
- Bluetooth L2CAP sockets
- CAIF sockets
- IUCV sockets
- Netlink sockets
- SCTP sockets
- Unix domain sockets
These remaining cases represent less common paths and could be converted
in a follow-up patch if needed. The current implementation provides
significantly improved observability into memory pressure events in the
network stack, especially for key protocols like TCP and UDP, helping to
diagnose problems in production environments.
Reported-by: Matt Fleming <mfleming@cloudflare.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://patch.msgid.link/175268316579.2407873.11634752355644843509.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a proper description for the sk_stream_write_space() function as
previously marked by a FIXME comment.
No functional changes.
Signed-off-by: Suchit Karunakaran <suchitkarunakaran@gmail.com>
Link: https://patch.msgid.link/20250716153404.7385-1-suchitkarunakaran@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 0937cb5f34 ("Revert "wifi: mac80211: Update
skb's control block key in ieee80211_tx_dequeue()"").
This commit broke TX with 802.11 encapsulation HW offloading, now that
this is fixed, reapply it.
Fixes: bb42f2d13f ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Link: https://patch.msgid.link/66b8fc39fb0194fa06c9ca7eeb6ffe0118dcb3ec.1752765971.git.repk@triplefau.lt
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
skb_get_hash() can only be used when the skb is linked to a netdev
device.
Signed-off-by: Alexander Wetzel <Alexander@wetzel-home.de>
Fixes: 73bc9e0af5 ("mac80211: don't apply flow control on management frames")
Link: https://patch.msgid.link/20250717162547.94582-3-Alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ignore TXQs with the flag IEEE80211_TXQ_STOP when scheduling a queue.
The flag is only set after all fragments have been dequeued and won't
allow dequeueing other frames as long as the flag is set.
For drivers using ieee80211_txq_schedule_start() this prevents an
loop trying to push the queued frames while IEEE80211_TXQ_STOP is set:
After setting IEEE80211_TXQ_STOP the driver will call
ieee80211_return_txq(). Which calls __ieee80211_schedule_txq(), detects
that there sill are frames in the queue and immediately restarts the
stopped TXQ. Which can't dequeue any frame and thus starts over the loop.
Signed-off-by: Alexander Wetzel <Alexander@wetzel-home.de>
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Link: https://patch.msgid.link/20250717162547.94582-2-Alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When short beaconing is enabled, check the value of the sb_count
to determine whether we are to send a long beacon or short beacon.
sb_count represents the number of short beacons until the next
long beacon, where if its value is 0 we are to send a long beacon.
The value is then reset to the long beacon period, which represents
the number of beacon intervals between each long beacon. The decrement
process follows the same cadence as the decrement of the DTIM count value.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250717074205.312577-5-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce the sb_count variable which tracks the number of
beacon intervals until the next long beacon. To initialise this
value, we find the current short beacon index into this period
which represents the number of short beacons left to send before
the next long beacon. We use the same TSF value used to initialise
the DTIM count to ensure the short beacon count and DTIM count
are in sync as its common for the long beacon period and DTIM period
to be equivalent.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250717074205.312577-4-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce the ability to parse the short beacon data and long
beacon period. The long beacon period represents the number of beacon
intervals between each long beacon transmission. Additionally,
as a BSS cannot change its configuration such that short beaconing
is dynamically disabled/enabled without tearing down the interface
- we ensure we have an existing short beacon before performing
the update.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250717074205.312577-3-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G short beacons are an optional frame type used in an S1G BSS
that contain a limited set of elements. While they are optional,
they are a fundamental part of S1G that enables significant
power saving.
Expose 2 additional netlink attributes,
NL80211_ATTR_S1G_LONG_BEACON_PERIOD which denotes the number of beacon
intervals between each long beacon and NL80211_ATTR_S1G_SHORT_BEACON
which is a nested attribute containing the short beacon tail and
head. We split them as the long beacon period cannot be updated,
and is only used when initialisng the interface, whereas the short
beacon data can be used to both initialise and update the templates.
This follows how things such as the beacon interval and DTIM period
currently operate.
During the initialisation path, we ensure we have the long beacon
period if the short beacon data is being passed down, whereas
the update path will simply update the template if its sent down.
The short beacon data is validated using the same routines for regular
beacons as they support correctly parsing the short beacon format
while ensuring the frame is well-formed.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250717074205.312577-2-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, reset connection monitor (ieee80211_sta_reset_conn_monitor())
timer is handled only for non-AP non-MLD STA and do not support non-AP MLD
STA. The current implementation checks for the CSA active and update the
monitor timer with the timeout value of deflink and reset the timer based
on the deflink's timeout value else schedule the connection loss work when
the deflink is timed out and it won't work for the non-AP MLD STA.
Handle the reset connection monitor timer for non-AP MLD STA by updating
the monitor timer with the timeout value which is determined based on the
link that will expire last among all the links in MLO. If at least one link
has not timed out, the timer is updated accordingly with the latest timeout
value else schedule the connection loss work when all links have timed out.
Remove the MLO-related WARN_ON() checks in the beacon and connection
monitoring logic code paths as they support MLO now.
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250718060837.59371-5-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, reset beacon monitor (ieee80211_sta_reset_beacon_monitor())
timer is handled only for non-AP non-MLD STA and do not support non-AP MLD
STA. When the beacon loss occurs in non-AP MLD STA with the current
implementation, it is treated as a single link and the timer will reset
based on the timeout of the deflink, without checking all the links.
Check the CSA flags for all the links in the MLO and decide whether to
schedule the work queue for beacon loss. If any of the links has CSA
active, then beacon loss work is not scheduled.
Also, call the functions ieee80211_sta_reset_beacon_monitor() and
ieee80211_sta_reset_conn_monitor() from ieee80211_csa_switch_work() only
when all the links are CSA active.
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250718060837.59371-4-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the existing macro for_each_link_data() uses sdata_dereference()
which requires the wiphy lock. This lock cannot be used in atomic or RCU
read-side contexts, such as in the RX path.
Introduce a new macro, for_each_link_data_rcu(), that iterates over link of
sdata using rcu_dereference(), making it safe to use in RCU contexts. This
allows callers to access link data without requiring the wiphy lock.
The macro takes into account the vif.valid_links bitmap and ensures only
valid links are accessed safely. Callers are responsible for ensuring that
rcu_read_lock() is held when using this macro.
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250718060837.59371-3-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The for_each_link_data() macro currently declares a local variable
__sdata directly, which could lead to compiler warnings or errors when
reused in the same function or within switch-case blocks due to variable
redefinition or invalid scoping.
To address this, restructure the macro to use an outer for-loop that runs
only once, allowing safe declaration of __sdata without polluting the outer
scope. This ensures compatibility with static analyzers.
No functional changes; this is purely a cleanup to improve macro hygiene.
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250718060837.59371-2-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This (partially) reverts commits
- 838c7b8f1f ("wifi: nl80211: Avoid address calculations via out of bounds array indexing")
- f1d3334d60 ("wifi: cfg80211: sme: init n_channels before channels[] access")
- 82bbe02b25 ("wifi: mac80211: Set n_channels after allocating struct cfg80211_scan_request")
These commits all set the structure to be in an inconsistent
state, setting n_channels to some value before them actually
being filled in. That's fine for what the code does now, but
with the removal of __counted_by() in 444020f4bf ("wifi:
cfg80211: remove scan request n_channels counted_by") it's no
longer needed and it does leave a bit of a landmine there
since breaking out of some code to send the scan or something
would leave it wrong.
Remove the now superfluous n_channels settings.
Link: https://patch.msgid.link/20250718103237.59510b2384c5.Ied5ba9c5c49efc008f4491c8ca7a45858a83f064@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ6NaUOruQGUkvPdG4raS+Z+3y5EwUCaHlCFwAKCRAraS+Z+3y5
E6qQAP9jVyIq+bKkZhRkew07cDNbYB01rJkJEO0Y/N7hnTyfwgD+PhiXGv5FiPp9
8iM3d51QKCOLlR/h3zc2RqR72S17RQA=
=ZaJz
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Martin KaFai Lau says:
====================
pull-request: bpf-next 2025-07-17
We've added 13 non-merge commits during the last 20 day(s) which contain
a total of 4 files changed, 712 insertions(+), 84 deletions(-).
The main changes are:
1) Avoid skipping or repeating a sk when using a TCP bpf_iter,
from Jordan Rife.
2) Clarify the driver requirement on using the XDP metadata,
from Song Yoong Siang
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next:
doc: xdp: Clarify driver implementation for XDP Rx metadata
selftests/bpf: Add tests for bucket resume logic in established sockets
selftests/bpf: Create iter_tcp_destroy test program
selftests/bpf: Create established sockets in socket iterator tests
selftests/bpf: Make ehash buckets configurable in socket iterator tests
selftests/bpf: Allow for iteration over multiple states
selftests/bpf: Allow for iteration over multiple ports
selftests/bpf: Add tests for bucket resume logic in listening sockets
bpf: tcp: Avoid socket skips and repeats during iteration
bpf: tcp: Use bpf_tcp_iter_batch_item for bpf_tcp_iter_state batch items
bpf: tcp: Get rid of st_bucket_done
bpf: tcp: Make sure iter->batch always contains a full bucket snapshot
bpf: tcp: Make mem flags configurable through bpf_iter_tcp_realloc_batch
====================
Link: https://patch.msgid.link/20250717191731.4142326-1-martin.lau@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
neigh_add() updates pneigh_entry() found or created by pneigh_create().
This update is serialised by RTNL, but we will remove it.
Let's move the update part to pneigh_create() and make it return errno
instead of a pointer of pneigh_entry.
Now, the pneigh code is RTNL free.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-16-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tbl->phash_buckets[] is only modified in the slow path by pneigh_create()
and pneigh_delete() under the table lock.
Both of them are called under RTNL, so no extra lock is needed, but we
will remove RTNL from the paths.
pneigh_create() looks up a pneigh_entry, and this part can be lockless,
but it would complicate the logic like
1. lookup
2. allocate pengih_entry for GFP_KERNEL
3. lookup again but under lock
4. if found, return it after freeing the allocated memory
5. else, return the new one
Instead, let's add a per-table mutex and run lookup and allocation
under it.
Note that updating pneigh_entry part in neigh_add() is still protected
by RTNL and will be moved to pneigh_create() in the next patch.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-15-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now, all callers of pneigh_lookup() are under RCU, and the read
lock there is no longer needed.
Let's drop the lock, inline __pneigh_lookup_1() to pneigh_lookup(),
and call it from pneigh_create().
The next patch will remove tbl->lock from pneigh_create().
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-14-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__pneigh_lookup() is the lockless version of pneigh_lookup(),
but its only caller pndisc_is_router() holds the table lock and
reads pneigh_netry.flags.
This is because accessing pneigh_entry after pneigh_lookup() was
illegal unless the caller holds RTNL or the table lock.
Now, pneigh_entry is guaranteed to be alive during the RCU critical
section.
Let's call pneigh_lookup() and use READ_ONCE() for n->flags in
pndisc_is_router() and remove __pneigh_lookup().
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-13-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now pneigh_entry is guaranteed to be alive during the
RCU critical section even without holding tbl->lock.
Let's use rcu_dereference() in pneigh_get_{first,next}().
Note that neigh_seq_start() still holds tbl->lock for the
normal neighbour entry.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-12-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now pneigh_entry is guaranteed to be alive during the
RCU critical section even without holding tbl->lock.
Let's drop read_lock_bh(&tbl->lock) and use rcu_dereference()
to iterate tbl->phash_buckets[] in pneigh_dump_table()
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-11-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Only __dev_get_by_index() is the RTNL dependant in neigh_get().
Let's replace it with dev_get_by_index_rcu() and convert RTM_GETNEIGH
to RCU.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-10-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will convert pneigh readers to RCU, and its flags and protocol
will be read locklessly.
Let's annotate the access to the two fields.
Note that all access to pn->permanent is under RTNL (neigh_add()
and pneigh_ifdown_and_unlock()), so WRITE_ONCE() and READ_ONCE()
are not needed.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-9-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will convert RTM_GETNEIGH to RCU.
neigh_get() looks up pneigh_entry by pneigh_lookup() and passes
it to pneigh_fill_info().
Then, we must ensure that the entry is alive till pneigh_fill_info()
completes, but read_lock_bh(&tbl->lock) in pneigh_lookup() does not
guarantee that.
Also, we will convert all readers of tbl->phash_buckets[] to RCU.
Let's use call_rcu() to free pneigh_entry and update phash_buckets[]
and ->next by rcu_assign_pointer().
pneigh_ifdown_and_unlock() uses list_head to avoid overwriting
->next and moving RCU iterators to another list.
pndisc_destructor() (only IPv6 ndisc uses this) uses a mutex, so it
is not delayed to call_rcu(), where we cannot sleep. This is fine
because the mcast code works with RCU and ipv6_dev_mc_dec() frees
mcast objects after RCU grace period.
While at it, we change the return type of pneigh_ifdown_and_unlock()
to void.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-8-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The next patch will free pneigh_entry with call_rcu().
Then, we need to annotate neigh_table.phash_buckets[] and
pneigh_entry.next with __rcu.
To make the next patch cleaner, let's annotate the fields in advance.
Currently, all accesses to the fields are under the neigh table lock,
so rcu_dereference_protected() is used with 1 for now, but most of them
(except in pneigh_delete() and pneigh_ifdown_and_unlock()) will be
replaced with rcu_dereference() and rcu_dereference_check().
Note that pneigh_ifdown_and_unlock() changes pneigh_entry.next to a
local list, which is illegal because the RCU iterator could be moved
to another list. This part will be fixed in the next patch.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-7-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pneigh_lookup() has ASSERT_RTNL() in the middle of the function, which
is confusing.
When called with the last argument, creat, 0, pneigh_lookup() literally
looks up a proxy neighbour entry. This is the case of the reader path
as the fast path and RTM_GETNEIGH.
pneigh_lookup(), however, creates a pneigh_entry when called with creat 1
from RTM_NEWNEIGH and SIOCSARP, which require RTNL.
Let's split pneigh_lookup() into two functions.
We will convert all the reader paths to RCU, and read_lock_bh(&tbl->lock)
in the new pneigh_lookup() will be dropped.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-6-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
neigh_valid_get_req() calls neigh_find_table() to fetch neigh_tables[].
neigh_find_table() uses rcu_dereference_rtnl(), but RTNL actually does
not protect it at all; neigh_table_clear() can be called without RTNL
and only waits for RCU readers by synchronize_rcu().
Fortunately, there is no bug because IPv4 is built-in, IPv6 cannot be
unloaded, and DECNET was removed.
To fetch neigh_tables[] by rcu_dereference() later, let's move
neigh_find_table() from neigh_valid_get_req() to neigh_get().
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-5-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will remove RTNL for neigh_get() and run it under RCU instead.
neigh_get_reply() and pneigh_get_reply() allocate skb with GFP_KERNEL.
Let's move the allocation before __dev_get_by_index() in neigh_get().
Now, neigh_get_reply() and pneigh_get_reply() are inlined and
rtnl_unicast() is factorised.
We will convert pneigh_lookup() to __pneigh_lookup() later.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-4-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will remove RTNL for neigh_get() and run it under RCU instead.
neigh_get() returns -EINVAL in the following cases:
* NDA_DST is not specified
* Both ndm->ndm_ifindex and NTF_PROXY are not specified
These validations do not require RCU.
Let's move them to neigh_valid_get_req().
While at it, the extack string for the first case is replaced with
NL_SET_ERR_ATTR_MISS().
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-3-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
neigh_get() passes 4 local variable pointers to neigh_valid_get_req().
If it returns a pointer of struct ndmsg, we do not need to pass two
of them.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250716221221.442239-2-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for ETHTOOL_SRXFH (setting hashing fields) in RSS_SET.
The tricky part is dealing with symmetric hashing. In netlink user
can change the hashing fields and symmetric hash in one request,
in IOCTL the two used to be set via different uAPI requests.
Since fields and hash function config are still separate driver
callbacks - changes to the two are not atomic. Keep things simple
and validate the settings against both pre- and post- change ones.
Meaning that we will reject the config request if user tries
to correct the flow fields and set input_xfrm in one request,
or disables input_xfrm and makes flow fields non-symmetric.
We can adjust it later if there's a real need. Starting simple feels
right, and potentially partially applying the settings isn't nice,
either.
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250716000331.1378807-11-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support configuring symmetric hashing via Netlink.
We have the flow field config prepared as part of SET handling,
so scan it for conflicts instead of querying the driver again.
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250716000331.1378807-10-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support setting RSS hashing key via ethtool Netlink.
Use the Netlink policy to make sure user doesn't pass
an empty key, "resetting" the key is not a thing.
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250716000331.1378807-7-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support setting RSS hash function / algo via ethtool Netlink.
Like IOCTL we don't validate that the function is within the
range known to the kernel. The drivers do a pretty good job
validating the inputs, and the IDs are technically "dynamically
queried" rather than part of uAPI.
Only change should be that in Netlink we don't support user
explicitly passing ETH_RSS_HASH_NO_CHANGE (0), if no change
is requested the attribute should be absent.
The ETH_RSS_HASH_NO_CHANGE is retained in driver-facing
API for consistency (not that I see a strong reason for it).
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250716000331.1378807-6-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add initial support for RSS_SET, for now only operations on
the indirection table are supported.
Unlike the ioctl don't check if at least one parameter is
being changed. This is how other ethtool-nl ops behave,
so pick the ethtool-nl consistency vs copying ioctl behavior.
There are two special cases here:
1) resetting the table to defaults;
2) support for tables of different size.
For (1) I use an empty Netlink attribute (array of size 0).
(2) may require some background. AFAICT a lot of modern devices
allow allocating RSS tables of different sizes. mlx5 can upsize
its tables, bnxt has some "table size calculation", and Intel
folks asked about RSS table sizing in context of resource allocation
in the past. The ethtool IOCTL API has a concept of table size,
but right now the user is expected to provide a table exactly
the size the device requests. Some drivers may change the table
size at runtime (in response to queue count changes) but the
user is not in control of this. What's not great is that all
RSS contexts share the same table size. For example a device
with 128 queues enabled, 16 RSS contexts 8 queues in each will
likely have 256 entry tables for each of the 16 contexts,
while 32 would be more than enough given each context only has
8 queues. To address this the Netlink API should avoid enforcing
table size at the uAPI level, and should allow the user to express
the min table size they expect.
To fully solve (2) we will need more driver plumbing but
at the uAPI level this patch allows the user to specify
a table size smaller than what the device advertises. The device
table size must be a multiple of the user requested table size.
We then replicate the user-provided table to fill the full device
size table. This addresses the "allow the user to express the min
table size" objective, while not enforcing any fixed size.
From Netlink perspective .get_rxfh_indir_size() is now de facto
the "max" table size supported by the device.
We may choose to support table replication in ethtool, too,
when we actually plumb this thru the device APIs.
Initially I was considering moving full pattern generation
to the kernel (which queues to use, at which frequency and
what min sequence length). I don't think this complexity
would buy us much and most if not all devices have pow-2
table sizes, which simplifies the replication a lot.
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250716000331.1378807-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- hci_sync: fix connectable extended advertising when using static random address
- hci_core: fix typos in macros
- hci_core: add missing braces when using macro parameters
- hci_core: replace 'quirks' integer by 'quirk_flags' bitmap
- SMP: If an unallowed command is received consider it a failure
- SMP: Fix using HCI_ERROR_REMOTE_USER_TERM on timeout
- L2CAP: Fix null-ptr-deref in l2cap_sock_resume_cb()
- L2CAP: Fix attempting to adjust outgoing MTU
- btintel: Check if controller is ISO capable on btintel_classify_pkt_type
- btusb: QCA: Fix downloading wrong NVM for WCN6855 GF variant without board ID
-----BEGIN PGP SIGNATURE-----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=JuS2
-----END PGP SIGNATURE-----
Merge tag 'for-net-2025-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- hci_sync: fix connectable extended advertising when using static random address
- hci_core: fix typos in macros
- hci_core: add missing braces when using macro parameters
- hci_core: replace 'quirks' integer by 'quirk_flags' bitmap
- SMP: If an unallowed command is received consider it a failure
- SMP: Fix using HCI_ERROR_REMOTE_USER_TERM on timeout
- L2CAP: Fix null-ptr-deref in l2cap_sock_resume_cb()
- L2CAP: Fix attempting to adjust outgoing MTU
- btintel: Check if controller is ISO capable on btintel_classify_pkt_type
- btusb: QCA: Fix downloading wrong NVM for WCN6855 GF variant without board ID
* tag 'for-net-2025-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: L2CAP: Fix attempting to adjust outgoing MTU
Bluetooth: btusb: QCA: Fix downloading wrong NVM for WCN6855 GF variant without board ID
Bluetooth: hci_dev: replace 'quirks' integer by 'quirk_flags' bitmap
Bluetooth: hci_core: add missing braces when using macro parameters
Bluetooth: hci_core: fix typos in macros
Bluetooth: SMP: Fix using HCI_ERROR_REMOTE_USER_TERM on timeout
Bluetooth: SMP: If an unallowed command is received consider it a failure
Bluetooth: btintel: Check if controller is ISO capable on btintel_classify_pkt_type
Bluetooth: hci_sync: fix connectable extended advertising when using static random address
Bluetooth: Fix null-ptr-deref in l2cap_sock_resume_cb()
====================
Link: https://patch.msgid.link/20250717142849.537425-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix rxrpc to use connection-level aborts for things that affect the whole
connection, such as the service ID not matching a local service.
Fixes: 57af281e53 ("rxrpc: Tidy up abort generation infrastructure")
Reported-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250717074350.3767366-6-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Under some circumstances, such as when a server socket is closing, ABORT
packets will be generated in response to incoming packets. Unfortunately,
this also may include generating aborts in response to incoming aborts -
which may cause a cycle. It appears this may be made possible by giving
the client a multicast address.
Fix this such that rxrpc_reject_packet() will refuse to generate aborts in
response to aborts.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Junvyyang, Tencent Zhuque Lab <zhuque@tencent.com>
cc: LePremierHomme <kwqcheii@proton.me>
cc: Linus Torvalds <torvalds@linux-foundation.org>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250717074350.3767366-5-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a call is released, rxrpc takes the spinlock and removes it from
->recvmsg_q in an effort to prevent racing recvmsg() invocations from
seeing the same call. Now, rxrpc_recvmsg() only takes the spinlock when
actually removing a call from the queue; it doesn't, however, take it in
the lead up to that when it checks to see if the queue is empty. It *does*
hold the socket lock, which prevents a recvmsg/recvmsg race - but this
doesn't prevent sendmsg from ending the call because sendmsg() drops the
socket lock and relies on the call->user_mutex.
Fix this by firstly removing the bit in rxrpc_release_call() that dequeues
the released call and, instead, rely on recvmsg() to simply discard
released calls (done in a preceding fix).
Secondly, rxrpc_notify_socket() is abandoned if the call is already marked
as released rather than trying to be clever by setting both pointers in
call->recvmsg_link to NULL to trick list_empty(). This isn't perfect and
can still race, resulting in a released call on the queue, but recvmsg()
will now clean that up.
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Junvyyang, Tencent Zhuque Lab <zhuque@tencent.com>
cc: LePremierHomme <kwqcheii@proton.me>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250717074350.3767366-4-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a call receives an event (such as incoming data), the call gets placed
on the socket's queue and a thread in recvmsg can be awakened to go and
process it. Once the thread has picked up the call off of the queue,
further events will cause it to be requeued, and once the socket lock is
dropped (recvmsg uses call->user_mutex to allow the socket to be used in
parallel), a second thread can come in and its recvmsg can pop the call off
the socket queue again.
In such a case, the first thread will be receiving stuff from the call and
the second thread will be blocked on call->user_mutex. The first thread
can, at this point, process both the event that it picked call for and the
event that the second thread picked the call for and may see the call
terminate - in which case the call will be "released", decoupling the call
from the user call ID assigned to it (RXRPC_USER_CALL_ID in the control
message).
The first thread will return okay, but then the second thread will wake up
holding the user_mutex and, if it sees that the call has been released by
the first thread, it will BUG thusly:
kernel BUG at net/rxrpc/recvmsg.c:474!
Fix this by just dequeuing the call and ignoring it if it is seen to be
already released. We can't tell userspace about it anyway as the user call
ID has become stale.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Reported-by: Junvyyang, Tencent Zhuque Lab <zhuque@tencent.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: LePremierHomme <kwqcheii@proton.me>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250717074350.3767366-3-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rxrpc_assess_MTU_size() function calls down into the IP layer to find
out the MTU size for a route. When accepting an incoming call, this is
called from rxrpc_new_incoming_call() which holds interrupts disabled
across the code that calls down to it. Unfortunately, the IP layer uses
local_bh_enable() which, config dependent, throws a warning if IRQs are
enabled:
WARNING: CPU: 1 PID: 5544 at kernel/softirq.c:387 __local_bh_enable_ip+0x43/0xd0
...
RIP: 0010:__local_bh_enable_ip+0x43/0xd0
...
Call Trace:
<TASK>
rt_cache_route+0x7e/0xa0
rt_set_nexthop.isra.0+0x3b3/0x3f0
__mkroute_output+0x43a/0x460
ip_route_output_key_hash+0xf7/0x140
ip_route_output_flow+0x1b/0x90
rxrpc_assess_MTU_size.isra.0+0x2a0/0x590
rxrpc_new_incoming_peer+0x46/0x120
rxrpc_alloc_incoming_call+0x1b1/0x400
rxrpc_new_incoming_call+0x1da/0x5e0
rxrpc_input_packet+0x827/0x900
rxrpc_io_thread+0x403/0xb60
kthread+0x2f7/0x310
ret_from_fork+0x2a/0x230
ret_from_fork_asm+0x1a/0x30
...
hardirqs last enabled at (23): _raw_spin_unlock_irq+0x24/0x50
hardirqs last disabled at (24): _raw_read_lock_irq+0x17/0x70
softirqs last enabled at (0): copy_process+0xc61/0x2730
softirqs last disabled at (25): rt_add_uncached_list+0x3c/0x90
Fix this by moving the call to rxrpc_assess_MTU_size() out of
rxrpc_init_peer() and further up the stack where it can be done without
interrupts disabled.
It shouldn't be a problem for rxrpc_new_incoming_call() to do it after the
locks are dropped as pmtud is going to be performed by the I/O thread - and
we're in the I/O thread at this point.
Fixes: a2ea9a9072 ("rxrpc: Use irq-disabling spinlocks between app and I/O thread")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Junvyyang, Tencent Zhuque Lab <zhuque@tencent.com>
cc: LePremierHomme <kwqcheii@proton.me>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250717074350.3767366-2-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
htb_lookup_leaf has a BUG_ON that can trigger with the following:
tc qdisc del dev lo root
tc qdisc add dev lo root handle 1: htb default 1
tc class add dev lo parent 1: classid 1:1 htb rate 64bit
tc qdisc add dev lo parent 1:1 handle 2: netem
tc qdisc add dev lo parent 2:1 handle 3: blackhole
ping -I lo -c1 -W0.001 127.0.0.1
The root cause is the following:
1. htb_dequeue calls htb_dequeue_tree which calls the dequeue handler on
the selected leaf qdisc
2. netem_dequeue calls enqueue on the child qdisc
3. blackhole_enqueue drops the packet and returns a value that is not
just NET_XMIT_SUCCESS
4. Because of this, netem_dequeue calls qdisc_tree_reduce_backlog, and
since qlen is now 0, it calls htb_qlen_notify -> htb_deactivate ->
htb_deactiviate_prios -> htb_remove_class_from_row -> htb_safe_rb_erase
5. As this is the only class in the selected hprio rbtree,
__rb_change_child in __rb_erase_augmented sets the rb_root pointer to
NULL
6. Because blackhole_dequeue returns NULL, netem_dequeue returns NULL,
which causes htb_dequeue_tree to call htb_lookup_leaf with the same
hprio rbtree, and fail the BUG_ON
The function graph for this scenario is shown here:
0) | htb_enqueue() {
0) + 13.635 us | netem_enqueue();
0) 4.719 us | htb_activate_prios();
0) # 2249.199 us | }
0) | htb_dequeue() {
0) 2.355 us | htb_lookup_leaf();
0) | netem_dequeue() {
0) + 11.061 us | blackhole_enqueue();
0) | qdisc_tree_reduce_backlog() {
0) | qdisc_lookup_rcu() {
0) 1.873 us | qdisc_match_from_root();
0) 6.292 us | }
0) 1.894 us | htb_search();
0) | htb_qlen_notify() {
0) 2.655 us | htb_deactivate_prios();
0) 6.933 us | }
0) + 25.227 us | }
0) 1.983 us | blackhole_dequeue();
0) + 86.553 us | }
0) # 2932.761 us | qdisc_warn_nonwc();
0) | htb_lookup_leaf() {
0) | BUG_ON();
------------------------------------------
The full original bug report can be seen here [1].
We can fix this just by returning NULL instead of the BUG_ON,
as htb_dequeue_tree returns NULL when htb_lookup_leaf returns
NULL.
[1] https://lore.kernel.org/netdev/pF5XOOIim0IuEfhI-SOxTgRvNoDwuux7UHKnE_Y5-zVd4wmGvNk2ceHjKb8ORnzw0cGwfmVu42g9dL7XyJLf1NEzaztboTWcm0Ogxuojoeo=@willsroot.io/
Fixes: 512bb43eb5 ("pkt_sched: sch_htb: Optimize WARN_ONs in htb_dequeue_tree() etc.")
Signed-off-by: William Liu <will@willsroot.io>
Signed-off-by: Savino Dicanosa <savy@syst3mfailure.io>
Link: https://patch.msgid.link/20250717022816.221364-1-will@willsroot.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Do not offload IGMP/MLD messages as it could lead to IGMP/MLD Reports
being unintentionally flooded to Hosts. Instead, let the bridge decide
where to send these IGMP/MLD messages.
Consider the case where the local host is sending out reports in response
to a remote querier like the following:
mcast-listener-process (IP_ADD_MEMBERSHIP)
\
br0
/ \
swp1 swp2
| |
QUERIER SOME-OTHER-HOST
In the above setup, br0 will want to br_forward() reports for
mcast-listener-process's group(s) via swp1 to QUERIER; but since the
source hwdom is 0, the report is eligible for tx offloading, and is
flooded by hardware to both swp1 and swp2, reaching SOME-OTHER-HOST as
well. (Example and illustration provided by Tobias.)
Fixes: 472111920f ("net: bridge: switchdev: allow the TX data plane forwarding to be offloaded")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20250716153551.1830255-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Assuming the "rx-vlan-filter" feature is enabled on a net device, the
8021q module will automatically add or remove VLAN 0 when the net device
is put administratively up or down, respectively. There are a couple of
problems with the above scheme.
The first problem is a memory leak that can happen if the "rx-vlan-filter"
feature is disabled while the device is running:
# ip link add bond1 up type bond mode 0
# ethtool -K bond1 rx-vlan-filter off
# ip link del dev bond1
When the device is put administratively down the "rx-vlan-filter"
feature is disabled, so the 8021q module will not remove VLAN 0 and the
memory will be leaked [1].
Another problem that can happen is that the kernel can automatically
delete VLAN 0 when the device is put administratively down despite not
adding it when the device was put administratively up since during that
time the "rx-vlan-filter" feature was disabled. null-ptr-unref or
bug_on[2] will be triggered by unregister_vlan_dev() for refcount
imbalance if toggling filtering during runtime:
$ ip link add bond0 type bond mode 0
$ ip link add link bond0 name vlan0 type vlan id 0 protocol 802.1q
$ ethtool -K bond0 rx-vlan-filter off
$ ifconfig bond0 up
$ ethtool -K bond0 rx-vlan-filter on
$ ifconfig bond0 down
$ ip link del vlan0
Root cause is as below:
step1: add vlan0 for real_dev, such as bond, team.
register_vlan_dev
vlan_vid_add(real_dev,htons(ETH_P_8021Q),0) //refcnt=1
step2: disable vlan filter feature and enable real_dev
step3: change filter from 0 to 1
vlan_device_event
vlan_filter_push_vids
ndo_vlan_rx_add_vid //No refcnt added to real_dev vlan0
step4: real_dev down
vlan_device_event
vlan_vid_del(dev, htons(ETH_P_8021Q), 0); //refcnt=0
vlan_info_rcu_free //free vlan0
step5: delete vlan0
unregister_vlan_dev
BUG_ON(!vlan_info); //vlan_info is null
Fix both problems by noting in the VLAN info whether VLAN 0 was
automatically added upon NETDEV_UP and based on that decide whether it
should be deleted upon NETDEV_DOWN, regardless of the state of the
"rx-vlan-filter" feature.
[1]
unreferenced object 0xffff8880068e3100 (size 256):
comm "ip", pid 384, jiffies 4296130254
hex dump (first 32 bytes):
00 20 30 0d 80 88 ff ff 00 00 00 00 00 00 00 00 . 0.............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc 81ce31fa):
__kmalloc_cache_noprof+0x2b5/0x340
vlan_vid_add+0x434/0x940
vlan_device_event.cold+0x75/0xa8
notifier_call_chain+0xca/0x150
__dev_notify_flags+0xe3/0x250
rtnl_configure_link+0x193/0x260
rtnl_newlink_create+0x383/0x8e0
__rtnl_newlink+0x22c/0xa40
rtnl_newlink+0x627/0xb00
rtnetlink_rcv_msg+0x6fb/0xb70
netlink_rcv_skb+0x11f/0x350
netlink_unicast+0x426/0x710
netlink_sendmsg+0x75a/0xc20
__sock_sendmsg+0xc1/0x150
____sys_sendmsg+0x5aa/0x7b0
___sys_sendmsg+0xfc/0x180
[2]
kernel BUG at net/8021q/vlan.c:99!
Oops: invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 0 UID: 0 PID: 382 Comm: ip Not tainted 6.16.0-rc3 #61 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:unregister_vlan_dev (net/8021q/vlan.c:99 (discriminator 1))
RSP: 0018:ffff88810badf310 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff88810da84000 RCX: ffffffffb47ceb9a
RDX: dffffc0000000000 RSI: 0000000000000008 RDI: ffff88810e8b43c8
RBP: 0000000000000000 R08: 0000000000000000 R09: fffffbfff6cefe80
R10: ffffffffb677f407 R11: ffff88810badf3c0 R12: ffff88810e8b4000
R13: 0000000000000000 R14: ffff88810642a5c0 R15: 000000000000017e
FS: 00007f1ff68c20c0(0000) GS:ffff888163a24000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f1ff5dad240 CR3: 0000000107e56000 CR4: 00000000000006f0
Call Trace:
<TASK>
rtnl_dellink (net/core/rtnetlink.c:3511 net/core/rtnetlink.c:3553)
rtnetlink_rcv_msg (net/core/rtnetlink.c:6945)
netlink_rcv_skb (net/netlink/af_netlink.c:2535)
netlink_unicast (net/netlink/af_netlink.c:1314 net/netlink/af_netlink.c:1339)
netlink_sendmsg (net/netlink/af_netlink.c:1883)
____sys_sendmsg (net/socket.c:712 net/socket.c:727 net/socket.c:2566)
___sys_sendmsg (net/socket.c:2622)
__sys_sendmsg (net/socket.c:2652)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
Fixes: ad1afb0039 ("vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)")
Reported-by: syzbot+a8b046e462915c65b10b@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=a8b046e462915c65b10b
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20250716034504.2285203-2-dongchenchen2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After recent changes in net-next TCP compacts skbs much more
aggressively. This unearthed a bug in TLS where we may try
to operate on an old skb when checking if all skbs in the
queue have matching decrypt state and geometry.
BUG: KASAN: slab-use-after-free in tls_strp_check_rcv+0x898/0x9a0 [tls]
(net/tls/tls_strp.c:436 net/tls/tls_strp.c:530 net/tls/tls_strp.c:544)
Read of size 4 at addr ffff888013085750 by task tls/13529
CPU: 2 UID: 0 PID: 13529 Comm: tls Not tainted 6.16.0-rc5-virtme
Call Trace:
kasan_report+0xca/0x100
tls_strp_check_rcv+0x898/0x9a0 [tls]
tls_rx_rec_wait+0x2c9/0x8d0 [tls]
tls_sw_recvmsg+0x40f/0x1aa0 [tls]
inet_recvmsg+0x1c3/0x1f0
Always reload the queue, fast path is to have the record in the queue
when we wake, anyway (IOW the path going down "if !strp->stm.full_len").
Fixes: 0d87bbd39d ("tls: strp: make sure the TCP skbs do not have overlapping data")
Link: https://patch.msgid.link/20250716143850.1520292-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A new warning in clang [1] points out a place in pep_sock_accept() where
dst is uninitialized then passed as a const pointer to pep_find_pipe():
net/phonet/pep.c:829:37: error: variable 'dst' is uninitialized when passed as a const pointer argument here [-Werror,-Wuninitialized-const-pointer]
829 | newsk = pep_find_pipe(&pn->hlist, &dst, pipe_handle);
| ^~~:
Move the call to pn_skb_get_dst_sockaddr(), which initializes dst, to
before the call to pep_find_pipe(), so that dst is consistently used
initialized throughout the function.
Cc: stable@vger.kernel.org
Fixes: f7ae8d59f6 ("Phonet: allocate sock from accept syscall rather than soft IRQ")
Link: 00dacf8c22 [1]
Closes: https://github.com/ClangBuiltLinux/linux/issues/2101
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20250715-net-phonet-fix-uninit-const-pointer-v1-1-8efd1bd188b3@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Configuration request only configure the incoming direction of the peer
initiating the request, so using the MTU is the other direction shall
not be used, that said the spec allows the peer responding to adjust:
Bluetooth Core 6.1, Vol 3, Part A, Section 4.5
'Each configuration parameter value (if any is present) in an
L2CAP_CONFIGURATION_RSP packet reflects an ‘adjustment’ to a
configuration parameter value that has been sent (or, in case of
default values, implied) in the corresponding
L2CAP_CONFIGURATION_REQ packet.'
That said adjusting the MTU in the response shall be limited to ERTM
channels only as for older modes the remote stack may not be able to
detect the adjustment causing it to silently drop packets.
Link: https://github.com/bluez/bluez/issues/1422
Link: https://gitlab.archlinux.org/archlinux/packaging/packages/linux/-/issues/149
Link: https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/4793
Fixes: 042bb9603c ("Bluetooth: L2CAP: Fix L2CAP MTU negotiation")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
- cfg80211: fix double-free introduced earlier
- mac80211: fix RCU iteration in CSA
- iwlwifi: many cleanups (unused FW APIs, PCIe code, WoWLAN)
- mac80211: some work around how FIPS affects wifi, which was
wrong (RC4 is used by TKIP, not only WEP)
- cfg/mac80211: improvements for unsolicated probe response
handling
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEpeA8sTs3M8SN2hR410qiO8sPaAAFAmh4xE8ACgkQ10qiO8sP
aAANTA/9HWfjfXTvZ3lEZqmOeJdHxd6xw3uHA732NF+KxoKi8vnO8V63WNVxBzCF
6srSaSi0IkdtnyR/uPqG5AkWej/ouAeDy+FtzoDpP8O6G4e9yjKZBRnvP+O/gkod
ERM4ouLWsumAIZqSqrSAJHgNTOP0/n5MNiLoKHlcjZmXphL2/lM8Qay7kVmWG+vT
tqv/LrwqRiTe/a+O9PKaW2sq6z23CBhEqWf6hhFCaEPVQXQJLBc6FTI4008zP/Rt
aSq672rMwA8ckuVOH0EAX544DMJc736to9XJEuu9EzuOaDZ9FwfqF9nOTMnFDev2
k9qn8Q5vsx+786A6pXw+sarnxhUxnQCYB00MhMe1e1yoB0lv57hZCD1Z0JTBGXPh
8ghmbelYBvkLollie6zUUcdf3G98ADUYvHsR0elBgGADWPHvnbn3ORVcv852X6jS
El1CR3lyvwwHn9USKaR91ESQWFRtLtPG+OmmLRLIG7wdkp0sDjHOpvV7A/7QpFLw
A18QrN+ORNL3Pja4A4dyIpDRQiTKHIjEEm3dAlVDzSWcPpcws5WlfreC1L71XblA
kRl+1I7SZ87rp8d6TXXxc8QmIMA+M4OL6M4FMAJgjn8VdyjlaC6lvl1i+tgdaDik
ISrY/78gnnt93BQmHU4P/syvh+NdpgNN+LgeaikKb1kmjG837Yk=
=g8VQ
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2025-07-17' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Another set of changes, notably:
- cfg80211: fix double-free introduced earlier
- mac80211: fix RCU iteration in CSA
- iwlwifi: many cleanups (unused FW APIs, PCIe code, WoWLAN)
- mac80211: some work around how FIPS affects wifi, which was
wrong (RC4 is used by TKIP, not only WEP)
- cfg/mac80211: improvements for unsolicated probe response
handling
* tag 'wireless-next-2025-07-17' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (64 commits)
wifi: cfg80211: fix double free for link_sinfo in nl80211_station_dump()
wifi: cfg80211: fix off channel operation allowed check for MLO
wifi: mac80211: use RCU-safe iteration in ieee80211_csa_finish
wifi: mac80211_hwsim: Update comments in header
wifi: mac80211: parse unsolicited broadcast probe response data
wifi: cfg80211: parse attribute to update unsolicited probe response template
wifi: mac80211: don't use TPE data from assoc response
wifi: mac80211: handle WLAN_HT_ACTION_NOTIFY_CHANWIDTH async
wifi: mac80211: simplify __ieee80211_rx_h_amsdu() loop
wifi: mac80211: don't mark keys for inactive links as uploaded
wifi: mac80211: only assign chanctx in reconfig
wifi: mac80211_hwsim: Declare support for AP scanning
wifi: mac80211: clean up cipher suite handling
wifi: mac80211: don't send keys to driver when fips_enabled
wifi: cfg80211: Fix interface type validation
wifi: mac80211: remove ieee80211_link_unreserve_chanctx() return value
wifi: mac80211: don't unreserve never reserved chanctx
mwl8k: Add missing check after DMA map
wifi: mac80211: make VHT opmode NSS ignore a debug message
wifi: iwlwifi: remove support of several iwl_ppag_table_cmd versions
...
====================
Link: https://patch.msgid.link/20250717094610.20106-47-johannes@sipsolutions.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=5X7Y
-----END PGP SIGNATURE-----
Merge tag 'nf-25-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following batch contains Netfilter fixes for net:
1) Three patches to enhance conntrack selftests for resize and clash
resolution, from Florian Westphal.
2) Expand nft_concat_range.sh selftest to improve coverage from error
path, from Florian Westphal.
3) Hide clash bit to userspace from netlink dumps until there is a
good reason to expose, from Florian Westphal.
4) Revert notification for device registration/unregistration for
nftables basechains and flowtables, we decided to go for a better
way to handle this through the nfnetlink_hook infrastructure which
will come via nf-next, patch from Phil Sutter.
5) Fix crash in conntrack due to race related to SLAB_TYPESAFE_BY_RCU
that results in removing a recycled object that is not yet in the
hashes. Move IPS_CONFIRM setting after the object is in the hashes.
From Florian Westphal.
netfilter pull request 25-07-17
* tag 'nf-25-07-17' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_conntrack: fix crash due to removal of uninitialised entry
Revert "netfilter: nf_tables: Add notifications for hook changes"
netfilter: nf_tables: hide clash bit from userspace
selftests: netfilter: nft_concat_range.sh: send packets to empty set
selftests: netfilter: conntrack_resize.sh: also use udpclash tool
selftests: netfilter: add conntrack clash resolution test case
selftests: netfilter: conntrack_resize.sh: extend resize test
====================
Link: https://patch.msgid.link/20250717095808.41725-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A crash in conntrack was reported while trying to unlink the conntrack
entry from the hash bucket list:
[exception RIP: __nf_ct_delete_from_lists+172]
[..]
#7 [ff539b5a2b043aa0] nf_ct_delete at ffffffffc124d421 [nf_conntrack]
#8 [ff539b5a2b043ad0] nf_ct_gc_expired at ffffffffc124d999 [nf_conntrack]
#9 [ff539b5a2b043ae0] __nf_conntrack_find_get at ffffffffc124efbc [nf_conntrack]
[..]
The nf_conn struct is marked as allocated from slab but appears to be in
a partially initialised state:
ct hlist pointer is garbage; looks like the ct hash value
(hence crash).
ct->status is equal to IPS_CONFIRMED|IPS_DYING, which is expected
ct->timeout is 30000 (=30s), which is unexpected.
Everything else looks like normal udp conntrack entry. If we ignore
ct->status and pretend its 0, the entry matches those that are newly
allocated but not yet inserted into the hash:
- ct hlist pointers are overloaded and store/cache the raw tuple hash
- ct->timeout matches the relative time expected for a new udp flow
rather than the absolute 'jiffies' value.
If it were not for the presence of IPS_CONFIRMED,
__nf_conntrack_find_get() would have skipped the entry.
Theory is that we did hit following race:
cpu x cpu y cpu z
found entry E found entry E
E is expired <preemption>
nf_ct_delete()
return E to rcu slab
init_conntrack
E is re-inited,
ct->status set to 0
reply tuplehash hnnode.pprev
stores hash value.
cpu y found E right before it was deleted on cpu x.
E is now re-inited on cpu z. cpu y was preempted before
checking for expiry and/or confirm bit.
->refcnt set to 1
E now owned by skb
->timeout set to 30000
If cpu y were to resume now, it would observe E as
expired but would skip E due to missing CONFIRMED bit.
nf_conntrack_confirm gets called
sets: ct->status |= CONFIRMED
This is wrong: E is not yet added
to hashtable.
cpu y resumes, it observes E as expired but CONFIRMED:
<resumes>
nf_ct_expired()
-> yes (ct->timeout is 30s)
confirmed bit set.
cpu y will try to delete E from the hashtable:
nf_ct_delete() -> set DYING bit
__nf_ct_delete_from_lists
Even this scenario doesn't guarantee a crash:
cpu z still holds the table bucket lock(s) so y blocks:
wait for spinlock held by z
CONFIRMED is set but there is no
guarantee ct will be added to hash:
"chaintoolong" or "clash resolution"
logic both skip the insert step.
reply hnnode.pprev still stores the
hash value.
unlocks spinlock
return NF_DROP
<unblocks, then
crashes on hlist_nulls_del_rcu pprev>
In case CPU z does insert the entry into the hashtable, cpu y will unlink
E again right away but no crash occurs.
Without 'cpu y' race, 'garbage' hlist is of no consequence:
ct refcnt remains at 1, eventually skb will be free'd and E gets
destroyed via: nf_conntrack_put -> nf_conntrack_destroy -> nf_ct_destroy.
To resolve this, move the IPS_CONFIRMED assignment after the table
insertion but before the unlock.
Pablo points out that the confirm-bit-store could be reordered to happen
before hlist add resp. the timeout fixup, so switch to set_bit and
before_atomic memory barrier to prevent this.
It doesn't matter if other CPUs can observe a newly inserted entry right
before the CONFIRMED bit was set:
Such event cannot be distinguished from above "E is the old incarnation"
case: the entry will be skipped.
Also change nf_ct_should_gc() to first check the confirmed bit.
The gc sequence is:
1. Check if entry has expired, if not skip to next entry
2. Obtain a reference to the expired entry.
3. Call nf_ct_should_gc() to double-check step 1.
nf_ct_should_gc() is thus called only for entries that already failed an
expiry check. After this patch, once the confirmed bit check passes
ct->timeout has been altered to reflect the absolute 'best before' date
instead of a relative time. Step 3 will therefore not remove the entry.
Without this change to nf_ct_should_gc() we could still get this sequence:
1. Check if entry has expired.
2. Obtain a reference.
3. Call nf_ct_should_gc() to double-check step 1:
4 - entry is still observed as expired
5 - meanwhile, ct->timeout is corrected to absolute value on other CPU
and confirm bit gets set
6 - confirm bit is seen
7 - valid entry is removed again
First do check 6), then 4) so the gc expiry check always picks up either
confirmed bit unset (entry gets skipped) or expiry re-check failure for
re-inited conntrack objects.
This change cannot be backported to releases before 5.19. Without
commit 8a75a2c174 ("netfilter: conntrack: remove unconfirmed list")
|= IPS_CONFIRMED line cannot be moved without further changes.
Cc: Razvan Cojocaru <rzvncj@gmail.com>
Link: https://lore.kernel.org/netfilter-devel/20250627142758.25664-1-fw@strlen.de/
Link: https://lore.kernel.org/netfilter-devel/4239da15-83ff-4ca4-939d-faef283471bb@gmail.com/
Fixes: 1397af5bfd ("netfilter: conntrack: remove the percpu dying list")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since "net: gro: use cb instead of skb->network_header", the skb network
header is no longer set in the GRO path.
This breaks fraglist segmentation, which relies on ip_hdr()/tcp_hdr()
to check for address/port changes.
Fix this regression by selectively setting the network header for merged
segment skbs.
Fixes: 186b1ea73a ("net: gro: use cb instead of skb->network_header")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250705150622.10699-1-nbd@nbd.name
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
pmc->idev is still used in ip6_mc_clear_src(), so as mld_clear_delrec()
does, the reference should be put after ip6_mc_clear_src() return.
Fixes: 63ed8de4be ("mld: add mc_lock for protecting per-interface mld data")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://patch.msgid.link/20250714141957.3301871-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use __skb_queue_purge() instead of re-implementing it. Note that it uses
kfree_skb_reason() instead of kfree_skb() internally, and pass
SKB_DROP_REASON_QUEUE_PURGE drop reason to the kfree_skb tracepoint.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20250715120709.3941510-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CI reported a UaF in tcp_prune_ofo_queue():
BUG: KASAN: slab-use-after-free in tcp_prune_ofo_queue+0x55d/0x660
Read of size 4 at addr ffff8880134729d8 by task socat/20348
CPU: 0 UID: 0 PID: 20348 Comm: socat Not tainted 6.16.0-rc5-virtme #1 PREEMPT(full)
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
<TASK>
dump_stack_lvl+0x82/0xd0
print_address_description.constprop.0+0x2c/0x400
print_report+0xb4/0x270
kasan_report+0xca/0x100
tcp_prune_ofo_queue+0x55d/0x660
tcp_try_rmem_schedule+0x855/0x12e0
tcp_data_queue+0x4dd/0x2260
tcp_rcv_established+0x5e8/0x2370
tcp_v4_do_rcv+0x4ba/0x8c0
__release_sock+0x27a/0x390
release_sock+0x53/0x1d0
tcp_sendmsg+0x37/0x50
sock_write_iter+0x3c1/0x520
vfs_write+0xc09/0x1210
ksys_write+0x183/0x1d0
do_syscall_64+0xc1/0x380
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fcf73ef2337
Code: 0f 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
RSP: 002b:00007ffd4f924708 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fcf73ef2337
RDX: 0000000000002000 RSI: 0000555f11d1a000 RDI: 0000000000000008
RBP: 0000555f11d1a000 R08: 0000000000002000 R09: 0000000000000000
R10: 0000000000000040 R11: 0000000000000246 R12: 0000000000000008
R13: 0000000000002000 R14: 0000555ee1a44570 R15: 0000000000002000
</TASK>
Allocated by task 20348:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
__kasan_slab_alloc+0x59/0x70
kmem_cache_alloc_node_noprof+0x110/0x340
__alloc_skb+0x213/0x2e0
tcp_collapse+0x43f/0xff0
tcp_try_rmem_schedule+0x6b9/0x12e0
tcp_data_queue+0x4dd/0x2260
tcp_rcv_established+0x5e8/0x2370
tcp_v4_do_rcv+0x4ba/0x8c0
__release_sock+0x27a/0x390
release_sock+0x53/0x1d0
tcp_sendmsg+0x37/0x50
sock_write_iter+0x3c1/0x520
vfs_write+0xc09/0x1210
ksys_write+0x183/0x1d0
do_syscall_64+0xc1/0x380
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 20348:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x38/0x50
kmem_cache_free+0x149/0x330
tcp_prune_ofo_queue+0x211/0x660
tcp_try_rmem_schedule+0x855/0x12e0
tcp_data_queue+0x4dd/0x2260
tcp_rcv_established+0x5e8/0x2370
tcp_v4_do_rcv+0x4ba/0x8c0
__release_sock+0x27a/0x390
release_sock+0x53/0x1d0
tcp_sendmsg+0x37/0x50
sock_write_iter+0x3c1/0x520
vfs_write+0xc09/0x1210
ksys_write+0x183/0x1d0
do_syscall_64+0xc1/0x380
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The buggy address belongs to the object at ffff888013472900
which belongs to the cache skbuff_head_cache of size 232
The buggy address is located 216 bytes inside of
freed 232-byte region [ffff888013472900, ffff8880134729e8)
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x13472
head: order:1 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
flags: 0x80000000000040(head|node=0|zone=1)
page_type: f5(slab)
raw: 0080000000000040 ffff88800198fb40 ffffea0000347b10 ffffea00004f5290
raw: 0000000000000000 0000000000120012 00000000f5000000 0000000000000000
head: 0080000000000040 ffff88800198fb40 ffffea0000347b10 ffffea00004f5290
head: 0000000000000000 0000000000120012 00000000f5000000 0000000000000000
head: 0080000000000001 ffffea00004d1c81 00000000ffffffff 00000000ffffffff
head: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888013472880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff888013472900: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff888013472980: fb fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc
^
ffff888013472a00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff888013472a80: fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb fb
Indeed tcp_prune_ofo_queue() is reusing the skb dropped a few lines
above. The caller wants to enqueue 'in_skb', lets check space vs the
latter.
Fixes: 1d2fbaad7c ("tcp: stronger sk_rcvbuf checks")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: syzbot+865aca08c0533171bf6a@syzkaller.appspotmail.com
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/b78d2d9bdccca29021eed9a0e7097dd8dc00f485.1752567053.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The requirement of ->get_rxfh_fields() in ethtool_set_rxfh() is there to
verify that we have no conflict of input_xfrm with the RSS fields
options, there is no point in doing it if input_xfrm is not
supported/requested.
This is under the assumption that a driver that supports input_xfrm will
also support ->get_rxfh_fields(), so add a WARN_ON() to
ethtool_check_ops() to verify it, and remove the op NULL check.
This fixes the following error in mlx4_en, which doesn't support
getting/setting RXFH fields.
$ ethtool --set-rxfh-indir eth2 hfunc xor
Cannot set RX flow hash configuration: Operation not supported
Fixes: 72792461c8 ("net: ethtool: don't mux RXFH via rxnfc callbacks")
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250715140754.489677-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'quirks' member already ran out of bits on some platforms some time
ago. Replace the integer member by a bitmap in order to have enough bits
in future. Replace raw bit operations by accessor macros.
Fixes: ff26b2dd65 ("Bluetooth: Add quirk for broken READ_VOICE_SETTING")
Fixes: 127881334e ("Bluetooth: Add quirk for broken READ_PAGE_SCAN_TYPE")
Suggested-by: Pauli Virtanen <pav@iki.fi>
Tested-by: Ivan Pravdin <ipravdin.official@gmail.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This replaces the usage of HCI_ERROR_REMOTE_USER_TERM, which as the name
suggest is to indicate a regular disconnection initiated by an user,
with HCI_ERROR_AUTH_FAILURE to indicate the session has timeout thus any
pairing shall be considered as failed.
Fixes: 1e91c29eb6 ("Bluetooth: Use hci_disconnect for immediate disconnection from SMP")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If a command is received while a bonding is ongoing consider it a
pairing failure so the session is cleanup properly and the device is
disconnected immediately instead of continuing with other commands that
may result in the session to get stuck without ever completing such as
the case bellow:
> ACL Data RX: Handle 2048 flags 0x02 dlen 21
SMP: Identity Information (0x08) len 16
Identity resolving key[16]: d7e08edef97d3e62cd2331f82d8073b0
> ACL Data RX: Handle 2048 flags 0x02 dlen 21
SMP: Signing Information (0x0a) len 16
Signature key[16]: 1716c536f94e843a9aea8b13ffde477d
Bluetooth: hci0: unexpected SMP command 0x0a from XX:XX:XX:XX:XX:XX
> ACL Data RX: Handle 2048 flags 0x02 dlen 12
SMP: Identity Address Information (0x09) len 7
Address: XX:XX:XX:XX:XX:XX (Intel Corporate)
While accourding to core spec 6.1 the expected order is always BD_ADDR
first first then CSRK:
When using LE legacy pairing, the keys shall be distributed in the
following order:
LTK by the Peripheral
EDIV and Rand by the Peripheral
IRK by the Peripheral
BD_ADDR by the Peripheral
CSRK by the Peripheral
LTK by the Central
EDIV and Rand by the Central
IRK by the Central
BD_ADDR by the Central
CSRK by the Central
When using LE Secure Connections, the keys shall be distributed in the
following order:
IRK by the Peripheral
BD_ADDR by the Peripheral
CSRK by the Peripheral
IRK by the Central
BD_ADDR by the Central
CSRK by the Central
According to the Core 6.1 for commands used for key distribution "Key
Rejected" can be used:
'3.6.1. Key distribution and generation
A device may reject a distributed key by sending the Pairing Failed command
with the reason set to "Key Rejected".
Fixes: b28b494366 ("Bluetooth: Add strict checks for allowed SMP PDUs")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Currently, the connectable flag used by the setup of an extended
advertising instance drives whether we require privacy when trying to pass
a random address to the advertising parameters (Own Address).
If privacy is not required, then it automatically falls back to using the
controller's public address. This can cause problems when using controllers
that do not have a public address set, but instead use a static random
address.
e.g. Assume a BLE controller that does not have a public address set.
The controller upon powering is set with a random static address by default
by the kernel.
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6
Address: E4:AF:26:D8:3E:3A (Static)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
Setting non-connectable extended advertisement parameters in bluetoothctl
mgmt
add-ext-adv-params -r 0x801 -x 0x802 -P 2M -g 1
correctly sets Own address type as Random
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036)
plen 25
...
Own address type: Random (0x01)
Setting connectable extended advertisement parameters in bluetoothctl mgmt
add-ext-adv-params -r 0x801 -x 0x802 -P 2M -g -c 1
mistakenly sets Own address type to Public (which causes to use Public
Address 00:00:00:00:00:00)
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036)
plen 25
...
Own address type: Public (0x00)
This causes either the controller to emit an Invalid Parameters error or to
mishandle the advertising.
This patch makes sure that we use the already set static random address
when requesting a connectable extended advertising when we don't require
privacy and our public address is not set (00:00:00:00:00:00).
Fixes: 3fe318ee72 ("Bluetooth: move hci_get_random_address() to hci_sync")
Signed-off-by: Alessandro Gasbarroni <alex.gasbarroni@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
mptcp_disconnect() clears the fallback bit unconditionally, without
touching the associated flags.
The bit clear is safe, as no fallback operation can race with that --
all subflow are already in TCP_CLOSE status thanks to the previous
FASTCLOSE -- but we need to consistently reset all the fallback related
status.
Also acquire the relevant lock, to avoid fouling static analyzers.
Fixes: b29fcfb54c ("mptcp: full disconnect implementation")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250714-net-mptcp-fallback-races-v1-3-391aff963322@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have races similar to the one addressed by the previous patch between
subflow failing and additional subflow creation. They are just harder to
trigger.
The solution is similar. Use a separate flag to track the condition
'socket state prevent any additional subflow creation' protected by the
fallback lock.
The socket fallback makes such flag true, and also receiving or sending
an MP_FAIL option.
The field 'allow_infinite_fallback' is now always touched under the
relevant lock, we can drop the ONCE annotation on write.
Fixes: 478d770008 ("mptcp: send out MP_FAIL when data checksum fails")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250714-net-mptcp-fallback-races-v1-2-391aff963322@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These is no need to check null for idev before return NULL.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250714081732.3109764-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rds_tcp_accept_one() starts with a pretty much verbatim
copy of kernel_accept(). Might as well use the real thing...
That code went into mainline in 2009, kernel_accept()
had been added in Aug 2006, the copyright on rds/tcp_listen.c
is "Copyright (c) 2006 Oracle", so it's entirely possible
that it predates the introduction of kernel_accept().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Link: https://patch.msgid.link/20250713180134.GC1880847@ZenIV
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prior to calling bind() a program may call connect() on a socket to
restrict to a remote peer address.
Using connect() is the normal mechanism to specify a remote network
peer, so we use that here. In MCTP connect() is only used for bound
sockets - send() is not available for MCTP since a tag must be provided
for each message.
The smctp_type must match between connect() and bind() calls.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Link: https://patch.msgid.link/20250710-mctp-bind-v4-6-8ec2f6460c56@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Ensure that a specific EID (remote or local) bind will match in
preference to a MCTP_ADDR_ANY bind.
This adds infrastructure for binding a socket to receive messages from a
specific remote peer address, a future commit will expose an API for
this.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Link: https://patch.msgid.link/20250710-mctp-bind-v4-5-8ec2f6460c56@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When a specific EID is passed as a bind address, it only makes sense to
interpret with an actual network ID, so resolve that to the default
network at bind time.
For bind address of MCTP_ADDR_ANY, we want to be able to capture traffic
to any network and address, so keep the current behaviour of matching
traffic from any network interface (don't interpret MCTP_NET_ANY as
the default network ID).
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Link: https://patch.msgid.link/20250710-mctp-bind-v4-3-8ec2f6460c56@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Disallow bind() calls that have the same arguments as existing bound
sockets. Previously multiple sockets could bind() to the same
type/local address, with an arbitrary socket receiving matched messages.
This is only a partial fix, a future commit will define precedence order
for MCTP_ADDR_ANY versus specific EID bind(), which are allowed to exist
together.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Link: https://patch.msgid.link/20250710-mctp-bind-v4-2-8ec2f6460c56@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The sock was not being released. Other than leaking, the stale socket
will conflict with subsequent bind() calls in unrelated MCTP tests.
Fixes: 46ee16462f ("net: mctp: test: Add extaddr routing output test")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Link: https://patch.msgid.link/20250710-mctp-bind-v4-1-8ec2f6460c56@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In cfg80211_off_channel_oper_allowed(), the current logic disallows
off-channel operations if any link operates on a radar channel,
assuming such channels cannot be vacated. This assumption holds for
non-MLO interfaces but not for MLO.
With MLO and multi-radio devices, different links may operate on
separate radios. This allows one link to scan off-channel while
another remains on a radar channel. For example, in a 5 GHz
split-phy setup, the lower band can scan while the upper band
stays on a radar channel.
Off-channel operations can be allowed if the radio/link onto which the
input channel falls is different from the radio/link which has an active
radar channel. Therefore, fix cfg80211_off_channel_oper_allowed() by
returning false only if the requested channel maps to the same radio as
an active radar channel. Allow off-channel operations when the requested
channel is on a different radio, as in MLO with multi-radio setups.
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Amith A <quic_amitajit@quicinc.com>
Link: https://patch.msgid.link/20250714040742.538550-1-quic_amitajit@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_csa_finish() function currently uses for_each_sdata_link()
to iterate over links of sdata. However, this macro internally uses
wiphy_dereference(), which expects the wiphy->mtx lock to be held.
When ieee80211_csa_finish() is invoked under an RCU read-side critical
section (e.g., under rcu_read_lock()), this leads to a warning from the
RCU debugging framework.
WARNING: suspicious RCU usage
net/mac80211/cfg.c:3830 suspicious rcu_dereference_protected() usage!
This warning is triggered because wiphy_dereference() is not safe to use
without holding the wiphy mutex, and it is being used in an RCU context
without the required locking.
Fix this by introducing and using a new macro, for_each_sdata_link_rcu(),
which performs RCU-safe iteration over sdata links using
list_for_each_entry_rcu() and rcu_dereference(). This ensures that the
link pointers are accessed safely under RCU and eliminates the warning.
Fixes: f600832794 ("wifi: mac80211: restructure tx profile retrieval for MLO MBSSID")
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250711033846.40455-1-maharaja.kennadyrajan@oss.qualcomm.com
[unindent like the non-RCU macro]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During commands like channel switch and color change, the updated
unsolicited broadcast probe response template may be provided. However,
this data is not parsed or acted upon in mac80211.
Add support to parse it and set the BSS changed flag
BSS_CHANGED_UNSOL_BCAST_PROBE_RESP so that drivers could take further
action.
Signed-off-by: Yuvarani V <quic_yuvarani@quicinc.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250710-update_unsol_bcast_probe_resp-v2-2-31aca39d3b30@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At present, the updated unsolicited broadcast probe response template is
not processed during userspace commands such as channel switch or color
change. This leads to an issue where older incorrect unsolicited probe
response is still used during these events.
Add support to parse the netlink attribute and store it so that
mac80211/drivers can use it to set the BSS_CHANGED_UNSOL_BCAST_PROBE_RESP
flag in order to send the updated unsolicited broadcast probe response
templates during these events.
Signed-off-by: Yuvarani V <quic_yuvarani@quicinc.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250710-update_unsol_bcast_probe_resp-v2-1-31aca39d3b30@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since there's no TPE element in the (re)assoc response, trying
to use the data from it just leads to using the defaults, even
though the real values had been set during authentication from
the discovered BSS information.
Fix this by simply not handling the TPE data in assoc response
since it's not intended to be present, if it changes later the
necessary changes will be made by tracking beacons later.
As a side effect, by passing the real frame subtype, now print
a correct value for ML reconfiguration responses.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250709233537.caa1ca853f5a.I588271f386731978163aa9d84ae75d6f79633e16@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If this action frame, with the value of IEEE80211_HT_CHANWIDTH_ANY,
arrives right after a beacon that changed the operational bandwidth from
20 MHz to 40 MHz, then updating the rate control bandwidth to 40 can
race with updating the chanctx width (that happens in the beacon
proccesing) back to 40 MHz:
cpu0 cpu1
ieee80211_rx_mgmt_beacon
ieee80211_config_bw
ieee80211_link_change_chanreq
(*)ieee80211_link_update_chanreq
ieee80211_rx_h_action
(**)ieee80211_sta_cur_vht_bw
(***) ieee80211_recalc_chanctx_chantype
in (**), the maximum between the capability width and the bss width is
returned. But the bss width was just updated to 40 in (*),
so the action frame handling code will increase the width of the rate
control before the chanctx was increased (in ***), leading to a FW error
(at least in iwlwifi driver. But this is wrong regardless).
Fix this by simply handling the action frame async, so it won't race
with the beacon proccessing.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218632
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250709233537.bb9dc6f36c35.I39782d6077424e075974c3bee4277761494a1527@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During resume, the driver can call ieee80211_add_gtk_rekey for keys that
are not programmed into the device, e.g. keys of inactive links.
Don't mark such a key as uploaded to avoid removing it later from the
driver/device.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250709233537.655094412b0b.Iacae31af3ba2a705da0a9baea976c2f799d65dc4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At the end of reconfig we are activating all the links that were active
before the error.
During the activation, _ieee80211_link_use_channel will unassign and
re-assign the chanctx from/to the link.
But we only need to do the assign, as we are re-building the state as it
was before the reconfig.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250709233537.6245c3ae7031.Ia5f68992c7c112bea8a426c9339f50c88be3a9ca@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Under the previous commit's assumption that FIPS isn't
supported by hardware, we don't need to modify the
cipher suite list, but just need to use the software
one instead of the driver's in this case, so clean up
the code.
Also fix it to exclude TKIP in this case, since that's
also dependent on RC4.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250709233537.cff427e8f8a5.I744d1ea6a37e3ea55ae8bc3e770acee734eff268@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When fips_enabled is set, don't send any keys to the driver
(including possibly WoWLAN KEK/KCK material), assuming that
no device exists with the necessary certifications. If this
turns out to be false in the future, we can add a HW flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250709233537.e5eebc2b19d8.I968ef8c9ffb48d464ada78685bd25d22349fb063@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All the paths that could return an error are considered
misuses of the function and WARN already, and none of
the callers ever check the return value. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250709233537.5b436ee3c20c.Ieff61ec510939adb5fe6da4840557b649b3aa820@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a link has no chanctx, indicating it is an inactive link
that we tracked CSA for, then attempting to unreserve the
reserved chanctx will throw a warning and fail, since there
never was a reserved chanctx. Skip the unreserve.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250709233537.022192f4b1ae.Ib58156ac13e674a9f4d714735be0764a244c0aae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
