Struct hsr_sup_tlv describes HW layout and therefore it needs a __packed
attribute to ensure the compiler does not add any padding.
Due to the size and __packed attribute of the structs that use
hsr_sup_tlv it has no functional impact.
Add __packed to struct hsr_sup_tlv.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding support for parsing the redbox supervision frames, the
author added `pull_size' and `total_pull_size' to track the amount of
bytes that were pulled from the skb during while parsing the skb so it
can be reverted/ pushed back at the end.
In the process probably copy&paste error occurred and for the HSRv1 case
the ethhdr was used instead of the hsr_tag. Later the hsr_tag was used
instead of hsr_sup_tag. The later error didn't matter because both
structs have the size so HSRv0 was still working. It broke however HSRv1
parsing because struct ethhdr is larger than struct hsr_tag.
Reinstate the old pulling flow and pull first ethhdr, hsr_tag in v1 case
followed by hsr_sup_tag.
[bigeasy: commit message]
Fixes: eafaa88b3e ("net: hsr: Add support for redbox supervision frames")'
Suggested-by: Tristram.Ha@microchip.com
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
introducted these but never implemented.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230729123456.36340-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When port-to-port forwarding for interfaces in HSR node is enabled,
disable promiscuous mode since L2 frame forward happens at the
offloaded hardware.
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230614114710.31400-1-r-gunasekaran@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If no frames has been exchanged with a node for HSR_NODE_FORGET_TIME, the
node will be deleted from the node_db list. If a frame is sent to the node
after it is deleted, a netdev_err message for each slave interface is
produced. This should not happen with dan nodes because of supervision
frames, but can happen often with san nodes, which clutters the kernel
log. Since the hsr protocol does not support sans, this is only relevant
for the prp protocol.
Signed-off-by: Kristian Overskeid <koverskeid@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
self_node_db is a list_head with one entry of struct hsr_node. The
purpose is to hold the two MAC addresses of the node itself.
It is convenient to recycle the structure. However having a list_head
and fetching always the first entry is not really optimal.
Created a new data strucure contaning the two MAC addresses named
hsr_self_node. Access that structure like an RCU protected pointer so
it can be replaced on the fly without blocking the reader.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
hsr_register_frame_out() compares new sequence_nr vs the old one
recorded in hsr_node::seq_out and if the new sequence_nr is higher then
it will be written to hsr_node::seq_out as the new value.
This operation isn't locked so it is possible that two frames with the
same sequence number arrive (via the two slave devices) and are fed to
hsr_register_frame_out() at the same time. Both will pass the check and
update the sequence counter later to the same value. As a result the
content of the same packet is fed into the stack twice.
This was noticed by running ping and observing DUP being reported from
time to time.
Instead of using the hsr_priv::seqnr_lock for the whole receive path (as
it is for sending in the master node) add an additional lock that is only
used for sequence number checks and updates.
Add a per-node lock that is used during sequence number reads and
updates.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sending frames via the hsr (master) device requires a sequence number
which is tracked in hsr_priv::sequence_nr and protected by
hsr_priv::seqnr_lock. Each time a new frame is sent, it will obtain a
new id and then send it via the slave devices.
Each time a packet is sent (via hsr_forward_do()) the sequence number is
checked via hsr_register_frame_out() to ensure that a frame is not
handled twice. This make sense for the receiving side to ensure that the
frame is not injected into the stack twice after it has been received
from both slave ports.
There is no locking to cover the sending path which means the following
scenario is possible:
CPU0 CPU1
hsr_dev_xmit(skb1) hsr_dev_xmit(skb2)
fill_frame_info() fill_frame_info()
hsr_fill_frame_info() hsr_fill_frame_info()
handle_std_frame() handle_std_frame()
skb1's sequence_nr = 1
skb2's sequence_nr = 2
hsr_forward_do() hsr_forward_do()
hsr_register_frame_out(, 2) // okay, send)
hsr_register_frame_out(, 1) // stop, lower seq duplicate
Both skbs (or their struct hsr_frame_info) received an unique id.
However since skb2 was sent before skb1, the higher sequence number was
recorded in hsr_register_frame_out() and the late arriving skb1 was
dropped and never sent.
This scenario has been observed in a three node HSR setup, with node1 +
node2 having ping and iperf running in parallel. From time to time ping
reported a missing packet. Based on tracing that missing ping packet did
not leave the system.
It might be possible (didn't check) to drop the sequence number check on
the sending side. But if the higher sequence number leaves on wire
before the lower does and the destination receives them in that order
and it will drop the packet with the lower sequence number and never
inject into the stack.
Therefore it seems the only way is to lock the whole path from obtaining
the sequence number and sending via dev_queue_xmit() and assuming the
packets leave on wire in the same order (and don't get reordered by the
NIC).
Cover the whole path for the master interface from obtaining the ID
until after it has been forwarded via hsr_forward_skb() to ensure the
skbs are sent to the NIC in the order of the assigned sequence numbers.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hsr device is a software device. Its
net_device_ops::ndo_start_xmit() routine will process the packet and
then pass the resulting skb to dev_queue_xmit().
During processing, hsr acquires a lock with spin_lock_bh()
(hsr_add_node()) which needs to be promoted to the _irq() suffix in
order to avoid a potential deadlock.
Then there are the warnings in dev_queue_xmit() (due to
local_bh_disable() with disabled interrupts) left.
Instead trying to address those (there is qdisc and…) for netpoll sake,
just disable netpoll on hsr.
Disable netpoll on hsr and replace the _irqsave() locking with _bh().
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Due to the hashed-MAC optimisation one problem become visible:
hsr_handle_sup_frame() walks over the list of available nodes and merges
two node entries into one if based on the information in the supervision
both MAC addresses belong to one node. The list-walk happens on a RCU
protected list and delete operation happens under a lock.
If the supervision arrives on both slave interfaces at the same time
then this delete operation can occur simultaneously on two CPUs. The
result is the first-CPU deletes the from the list and the second CPUs
BUGs while attempting to dereference a poisoned list-entry. This happens
more likely with the optimisation because a new node for the mac_B entry
is created once a packet has been received and removed (merged) once the
supervision frame has been received.
Avoid removing/ cleaning up a hsr_node twice by adding a `removed' field
which is set to true after the removal and checked before the removal.
Fixes: f266a683a4 ("net/hsr: Better frame dispatch")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
hsr_forward_skb() a skb and keeps information in an on-stack
hsr_frame_info. hsr_get_node() assigns hsr_frame_info::node_src which is
from a RCU list. This pointer is used later in hsr_forward_do().
I don't see a reason why this pointer can't vanish midway since there is
no guarantee that hsr_forward_skb() is invoked from an RCU read section.
Use rcu_read_lock() to protect hsr_frame_info::node_src from its
assignment until it is no longer used.
Fixes: f266a683a4 ("net/hsr: Better frame dispatch")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hlist optimisation (which not only uses hlist_head instead of
list_head but also splits hsr_priv::node_db into an array of 256 slots)
does not consider the "node merge":
Upon starting the hsr network (with three nodes) a packet that is
sent from node1 to node3 will also be sent from node1 to node2 and then
forwarded to node3.
As a result node3 will receive 2 packets because it is not able
to filter out the duplicate. Each packet received will create a new
struct hsr_node with macaddress_A only set the MAC address it received
from (the two MAC addesses from node1).
At some point (early in the process) two supervision frames will be
received from node1. They will be processed by hsr_handle_sup_frame()
and one frame will leave early ("Node has already been merged") and does
nothing. The other frame will be merged as portB and have its MAC
address written to macaddress_B and the hsr_node (that was created for
it as macaddress_A) will be removed.
From now on HSR is able to identify a duplicate because both packets
sent from one node will result in the same struct hsr_node because
hsr_get_node() will find the MAC address either on macaddress_A or
macaddress_B.
Things get tricky with the optimisation: If sender's MAC address is
saved as macaddress_A then the lookup will work as usual. If the MAC
address has been merged into macaddress_B of another hsr_node then the
lookup won't work because it is likely that the data structure is in
another bucket. This results in creating a new struct hsr_node and not
recognising a possible duplicate.
A way around it would be to add another hsr_node::mac_list_B and attach
it to the other bucket to ensure that this hsr_node will be looked up
either via macaddress_A _or_ macaddress_B.
I however prefer to revert it because it sounds like an academic problem
rather than real life workload plus it adds complexity. I'm not an HSR
expert with what is usual size of a network but I would guess 40 to 60
nodes. With 10.000 nodes and assuming 60us for pass-through (from node
to node) then it would take almost 600ms for a packet to almost wrap
around which sounds a lot.
Revert the hash MAC addresses optimisation.
Fixes: 4acc45db71 ("net: hsr: use hlist_head instead of list_head for mac addresses")
Cc: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The skb is delivered to netif_rx() which may free it, after calling this,
dereferencing skb may trigger use-after-free.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20221125075724.27912-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We had historically not checked that genlmsghdr.reserved
is 0 on input which prevents us from using those precious
bytes in the future.
One use case would be to extend the cmd field, which is
currently just 8 bits wide and 256 is not a lot of commands
for some core families.
To make sure that new families do the right thing by default
put the onus of opting out of validation on existing families.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paul Moore <paul@paul-moore.com> (NetLabel)
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before adding yet another possibly contended atomic_long_t,
it is time to add per-cpu storage for existing ones:
dev->tx_dropped, dev->rx_dropped, and dev->rx_nohandler
Because many devices do not have to increment such counters,
allocate the per-cpu storage on demand, so that dev_get_stats()
does not have to spend considerable time folding zero counters.
Note that some drivers have abused these counters which
were supposed to be only used by core networking stack.
v4: should use per_cpu_ptr() in dev_get_stats() (Jakub)
v3: added a READ_ONCE() in netdev_core_stats_alloc() (Paolo)
v2: add a missing include (reported by kernel test robot <lkp@intel.com>)
Change in netdev_core_stats_alloc() (Jakub)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: jeffreyji <jeffreyji@google.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220311051420.2608812-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Network drivers such as igb or igc call eth_get_headlen() to determine the
header length for their to be constructed skbs in receive path.
When running HSR on top of these drivers, it results in triggering BUG_ON() in
skb_pull(). The reason is the skb headlen is not sufficient for HSR to work
correctly. skb_pull() notices that.
For instance, eth_get_headlen() returns 14 bytes for TCP traffic over HSR which
is not correct. The problem is, the flow dissection code does not take HSR into
account. Therefore, add support for it.
Reported-by: Anthony Harivel <anthony.harivel@linutronix.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20220228195856.88187-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In hsr, lockdep_is_held() is needed for rcu_dereference_bh_check().
But if lockdep is not enabled, lockdep_is_held() causes a build error:
ERROR: modpost: "lockdep_is_held" [net/hsr/hsr.ko] undefined!
Thus, this patch solved by adding lockdep_hsr_is_held(). This helper
function calls the lockdep_is_held() when lockdep is enabled, and returns 1
if not defined.
Fixes: e7f2742068 ("net: hsr: fix suspicious RCU usage warning in hsr_node_get_first()")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Link: https://lore.kernel.org/r/20220220153250.5285-1-claudiajkang@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, HSR manages mac addresses of known HSR nodes by using list_head.
It takes a lot of time when there are a lot of registered nodes due to
finding specific mac address nodes by using linear search. We can be
reducing the time by using hlist. Thus, this patch moves list_head to
hlist_head for mac addresses and this allows for further improvement of
network performance.
Condition: registered 10,000 known HSR nodes
Before:
# iperf3 -c 192.168.10.1 -i 1 -t 10
Connecting to host 192.168.10.1, port 5201
[ 5] local 192.168.10.2 port 59442 connected to 192.168.10.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.49 sec 3.75 MBytes 21.1 Mbits/sec 0 158 KBytes
[ 5] 1.49-2.05 sec 1.25 MBytes 18.7 Mbits/sec 0 166 KBytes
[ 5] 2.05-3.06 sec 2.44 MBytes 20.3 Mbits/sec 56 16.9 KBytes
[ 5] 3.06-4.08 sec 1.43 MBytes 11.7 Mbits/sec 11 38.0 KBytes
[ 5] 4.08-5.00 sec 951 KBytes 8.49 Mbits/sec 0 56.3 KBytes
After:
# iperf3 -c 192.168.10.1 -i 1 -t 10
Connecting to host 192.168.10.1, port 5201
[ 5] local 192.168.10.2 port 36460 connected to 192.168.10.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 7.39 MBytes 62.0 Mbits/sec 3 130 KBytes
[ 5] 1.00-2.00 sec 5.06 MBytes 42.4 Mbits/sec 16 113 KBytes
[ 5] 2.00-3.00 sec 8.58 MBytes 72.0 Mbits/sec 42 94.3 KBytes
[ 5] 3.00-4.00 sec 7.44 MBytes 62.4 Mbits/sec 2 131 KBytes
[ 5] 4.00-5.07 sec 8.13 MBytes 63.5 Mbits/sec 38 92.9 KBytes
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The writer acquires dev_base_lock with disabled bottom halves.
The reader can acquire dev_base_lock without disabling bottom halves
because there is no writer in softirq context.
On PREEMPT_RT the softirqs are preemptible and local_bh_disable() acts
as a lock to ensure that resources, that are protected by disabling
bottom halves, remain protected.
This leads to a circular locking dependency if the lock acquired with
disabled bottom halves (as in write_lock_bh()) and somewhere else with
enabled bottom halves (as by read_lock() in netstat_show()) followed by
disabling bottom halves (cxgb_get_stats() -> t4_wr_mbox_meat_timeout()
-> spin_lock_bh()). This is the reverse locking order.
All read_lock() invocation are from sysfs callback which are not invoked
from softirq context. Therefore there is no need to disable bottom
halves while acquiring a write lock.
Acquire the write lock of dev_base_lock without disabling bottom halves.
Reported-by: Pei Zhang <pezhang@redhat.com>
Reported-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
added support for the redbox supervision frames
as defined in the IEC-62439-3:2018.
Signed-off-by: Andreas Oetken <andreas.oetken@siemens-energy.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_create_self_node() may get netdev->dev_addr
passed as argument, netdev->dev_addr will be
const soon.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't check the sequence number when deciding when to update time_in in
the node table if tag removal is offloaded since the sequence number is
part of the tag. This fixes a problem where the times in the node table
wouldn't update when 0 appeared to be before or equal to seq_out when
tag removal was offloaded.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2e9f60932a ("net: hsr: check skb can contain struct hsr_ethhdr
in fill_frame_info") added the following which resulted in -EINVAL
always being returned:
if (skb->mac_len < sizeof(struct hsr_ethhdr))
return -EINVAL;
mac_len was not being set correctly so this check completely broke
HSR/PRP since it was always 14, not 20.
Set mac_len correctly and modify the mac_len checks to test in the
correct places since sometimes it is legitimately 14.
Fixes: 2e9f60932a ("net: hsr: check skb can contain struct hsr_ethhdr in fill_frame_info")
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check at start of fill_frame_info that the MAC header in the supplied
skb is large enough to fit a struct hsr_ethhdr, as otherwise this is
not a valid HSR frame. If it is too small, return an error which will
then cause the callers to clean up the skb. Fixes a KMSAN-found
uninit-value bug reported by syzbot at:
https://syzkaller.appspot.com/bug?id=f7e9b601f1414f814f7602a82b6619a8d80bce3f
Reported-by: syzbot+e267bed19bfc5478fb33@syzkaller.appspotmail.com
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reset MAC header in HSR Tx path. This is needed, because direct packet
transmission, e.g. by specifying PACKET_QDISC_BYPASS does not reset the MAC
header.
This has been observed using the following setup:
|$ ip link add name hsr0 type hsr slave1 lan0 slave2 lan1 supervision 45 version 1
|$ ifconfig hsr0 up
|$ ./test hsr0
The test binary is using mmap'ed sockets and is specifying the
PACKET_QDISC_BYPASS socket option.
This patch resolves the following warning on a non-patched kernel:
|[ 112.725394] ------------[ cut here ]------------
|[ 112.731418] WARNING: CPU: 1 PID: 257 at net/hsr/hsr_forward.c:560 hsr_forward_skb+0x484/0x568
|[ 112.739962] net/hsr/hsr_forward.c:560: Malformed frame (port_src hsr0)
The warning can be safely removed, because the other call sites of
hsr_forward_skb() make sure that the skb is prepared correctly.
Fixes: d346a3fae3 ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A typo is found out by codespell tool in 111th line of hsr_debugfs.c:
$ codespell ./net/hsr/
net/hsr/hsr_debugfs.c:111: Debufs ==> Debugfs
Fix typos found by codespell.
Signed-off-by: Xiong Zhenwu <xiong.zhenwu@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In IEC 62439-3 EntryForgetTime is defined with a value of 400 ms. When a
node does not send any frame within this time, the sequence number check
for can be ignored. This solves communication issues with Cisco IE 2000
in Redbox mode.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Marco Wenzel <marco.wenzel@a-eberle.de>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210224094653.1440-1-marco.wenzel@a-eberle.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for offloading of HSR/PRP (IEC 62439-3) tag insertion
tag removal, duplicate generation and forwarding.
For HSR, insertion involves the switch adding a 6 byte HSR header after
the 14 byte Ethernet header. For PRP it adds a 6 byte trailer.
Tag removal involves automatically stripping the HSR/PRP header/trailer
in the switch. This is possible when the switch also performs auto
deduplication using the HSR/PRP header/trailer (making it no longer
required).
Forwarding involves automatically forwarding between redundant ports in
an HSR. This is crucial because delay is accumulated as a frame passes
through each node in the ring.
Duplication involves the switch automatically sending a single frame
from the CPU port to both redundant ports. This is required because the
inserted HSR/PRP header/trailer must contain the same sequence number
on the frames sent out both redundant ports.
Export is_hsr_master so DSA can tell them apart from other devices in
dsa_slave_changeupper.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a switch to offload insertion of HSR/PRP tags, frames must not be
sent to the CPU facing switch port with a tag. Generate supervision frames
(eth type ETH_P_PRP) without HSR v1 (ETH_P_HSR)/PRP tag and rely on
create_tagged_frame which inserts it later. This will allow skipping the
tag insertion for all outgoing frames in the future which is required for
HSR v1/PRP tag insertions to be offloaded.
HSR v0 supervision frames always contain tag information so insertion of
the tag can't be offloaded. IEC 62439-3 Ed.2.0 (HSR v1) specifically
notes that this was changed since v0 to allow offloading.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sup_multicast_addr is passed to ether_addr_equal for address comparison
which casts the address inputs to u16 leading to an unaligned access.
Aligning the sup_multicast_addr to u16 boundary fixes the issue.
Signed-off-by: Andreas Oetken <andreas.oetken@siemens.com>
Link: https://lore.kernel.org/r/20210202090304.2740471-1-ennoerlangen@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bulk of the genetlink users can use smaller ops, move them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clean follow coccicheck warning:
net//hsr/hsr_netlink.c:94:8-42: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
net//hsr/hsr_netlink.c:87:30-57: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
net//hsr/hsr_netlink.c:79:29-53: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to %pM instead of using custom code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print PRP specific information from node table as part of debugfs
node table display. Also display the node as DAN-H or DAN-P depending
on the info from node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DAN-P (Dual Attached Nodes PRP) nodes are expected to receive
traditional IP packets as well as PRP (Parallel Redundancy
Protocol) tagged (trailer) packets. PRP trailer is 6 bytes
of PRP protocol unit called RCT, Redundancy Control Trailer
(RCT) similar to HSR tag. PRP network can have traditional
devices such as bridges/switches or PC attached to it and
should be able to communicate. Regular Ethernet devices treat
the RCT as pads. This patch adds logic to format L2 frames
from network stack to add a trailer (RCT) and send it as
duplicates over the slave interfaces when the protocol is
PRP as per IEC 62439-3. At the ingress, it strips the trailer,
do duplicate detection and rejection and forward a stripped
frame up the network stack. PRP device should accept frames
from Singly Attached Nodes (SAN) and thus the driver mark
the link where the frame came from in the node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce PRP, refactor the code specific to
handling HSR frames into separate functions and call them through
proto_ops function pointers.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for generation of PRP supervision frames. For PRP,
supervision frame format is similar to HSR version 0, but have
a PRP Redundancy Control Trailer (RCT) added and uses a different
message type, PRP_TLV_LIFE_CHECK_DD. Also update
is_supervision_frame() to include the new message type used for
PRP supervision frame.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce support for PRP protocol, add a
protocol ops ptr in the private hsr structure to hold function
pointers as some of the functions at protocol level packet
handling is different for HSR vs PRP. It is expected that PRP will
add its of set of functions for protocol handling. Modify existing
hsr_announce() function to call proto_ops->send_sv_frame() to send
supervision frame for HSR. This is expected to be different for PRP.
So introduce a ops function ptr, send_sv_frame() for the same and
initialize it to send_hsr_supervsion_frame(). Modify hsr_announce()
to call proto_ops->send_sv_frame().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce PRP protocol support in the
driver, refactor the skb init code to a separate function.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parallel Redundancy Protocol (PRP) is another redundancy protocol
introduced by IEC 63439 standard. It is similar to HSR in many
aspects:-
- Use a pair of Ethernet interfaces to created the PRP device
- Use a 6 byte redundancy protocol part (RCT, Redundancy Check
Trailer) similar to HSR Tag.
- Has Link Redundancy Entity (LRE) that works with RCT to implement
redundancy.
Key difference is that the protocol unit is a trailer instead of a
prefix as in HSR. That makes it inter-operable with tradition network
components such as bridges/switches which treat it as pad bytes,
whereas HSR nodes requires some kind of translators (Called redbox) to
talk to regular network devices. This features allows regular linux box
to be converted to a DAN-P box. DAN-P stands for Dual Attached Node - PRP
similar to DAN-H (Dual Attached Node - HSR).
Add a comment at the header/source code to explicitly state that the
driver files also handles PRP protocol as well.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Because kfree_skb already checked NULL skb parameter,
so the additional checks are unnecessary, just remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_put_padto() can fail. So check for return type and return NULL
for skb. Caller checks for skb and acts correctly if it is NULL.
Fixes: 6d6148bc78 ("net: hsr: fix incorrect lsdu size in the tag of HSR frames for small frames")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate MAC address before copying the same to outgoing frame
skb destination address. Since a node can have zero mac
address for Link B until a valid frame is received over
that link, this fix address the issue of a zero MAC address
being in the packet.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For small Ethernet frames with size less than minimum size 66 for HSR
vs 60 for regular Ethernet frames, hsr driver currently doesn't pad the
frame to make it minimum size. This results in incorrect LSDU size being
populated in the HSR tag for these frames. Fix this by padding the frame
to the minimum size applicable for HSR.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is being deleted, "/proc/net/dev_snmp6/<interface name>"
is deleted.
The function for this is addrconf_ifdown() in the addrconf_notify() and
it is called by notification, which is NETDEV_UNREGISTER.
But, if NETDEV_CHANGEMTU is triggered after NETDEV_UNREGISTER,
this proc file will be created again.
This recreated proc file will be deleted by netdev_wati_allrefs().
Before netdev_wait_allrefs() is called, creating a new HSR interface
routine can be executed and It tries to create a proc file but it will
find an un-deleted proc file.
At this point, it warns about it.
To avoid this situation, it can use ->dellink() instead of
->ndo_uninit() to release resources because ->dellink() is called
before NETDEV_UNREGISTER.
So, a proc file will not be recreated.
Test commands
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link set dummy0 mtu 1300
#SHELL1
while :
do
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
done
#SHELL2
while :
do
ip link del hsr0
done
Splat looks like:
[ 9888.980852][ T2752] proc_dir_entry 'dev_snmp6/hsr0' already registered
[ 9888.981797][ C2] WARNING: CPU: 2 PID: 2752 at fs/proc/generic.c:372 proc_register+0x2d5/0x430
[ 9888.981798][ C2] Modules linked in: hsr dummy veth openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_ipv6x
[ 9888.981814][ C2] CPU: 2 PID: 2752 Comm: ip Tainted: G W 5.8.0-rc1+ #616
[ 9888.981815][ C2] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 9888.981816][ C2] RIP: 0010:proc_register+0x2d5/0x430
[ 9888.981818][ C2] Code: fc ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 65 01 00 00 49 8b b5 e0 00 00 00 48 89 ea 40
[ 9888.981819][ C2] RSP: 0018:ffff8880628dedf0 EFLAGS: 00010286
[ 9888.981821][ C2] RAX: dffffc0000000008 RBX: ffff888028c69170 RCX: ffffffffaae09a62
[ 9888.981822][ C2] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff88806c9f75ac
[ 9888.981823][ C2] RBP: ffff888028c693f4 R08: ffffed100d9401bd R09: ffffed100d9401bd
[ 9888.981824][ C2] R10: ffffffffaddf406f R11: 0000000000000001 R12: ffff888028c69308
[ 9888.981825][ C2] R13: ffff8880663584c8 R14: dffffc0000000000 R15: ffffed100518d27e
[ 9888.981827][ C2] FS: 00007f3876b3b0c0(0000) GS:ffff88806c800000(0000) knlGS:0000000000000000
[ 9888.981828][ C2] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 9888.981829][ C2] CR2: 00007f387601a8c0 CR3: 000000004101a002 CR4: 00000000000606e0
[ 9888.981830][ C2] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 9888.981831][ C2] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 9888.981832][ C2] Call Trace:
[ 9888.981833][ C2] ? snmp6_seq_show+0x180/0x180
[ 9888.981834][ C2] proc_create_single_data+0x7c/0xa0
[ 9888.981835][ C2] snmp6_register_dev+0xb0/0x130
[ 9888.981836][ C2] ipv6_add_dev+0x4b7/0xf60
[ 9888.981837][ C2] addrconf_notify+0x684/0x1ca0
[ 9888.981838][ C2] ? __mutex_unlock_slowpath+0xd0/0x670
[ 9888.981839][ C2] ? kasan_unpoison_shadow+0x30/0x40
[ 9888.981840][ C2] ? wait_for_completion+0x250/0x250
[ 9888.981841][ C2] ? inet6_ifinfo_notify+0x100/0x100
[ 9888.981842][ C2] ? dropmon_net_event+0x227/0x410
[ 9888.981843][ C2] ? notifier_call_chain+0x90/0x160
[ 9888.981844][ C2] ? inet6_ifinfo_notify+0x100/0x100
[ 9888.981845][ C2] notifier_call_chain+0x90/0x160
[ 9888.981846][ C2] register_netdevice+0xbe5/0x1070
[ ... ]
Reported-by: syzbot+1d51c8b74efa4c44adeb@syzkaller.appspotmail.com
Fixes: e0a4b99773 ("hsr: use upper/lower device infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
When VLAN frame is being sent, hsr calls WARN_ONCE() because hsr doesn't
support VLAN. But using WARN_ONCE() is overdoing.
Using netdev_warn_once() is enough.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following sparse checker warning:-
net/hsr/hsr_slave.c:38:18: warning: incorrect type in assignment (different base types)
net/hsr/hsr_slave.c:38:18: expected unsigned short [unsigned] [usertype] protocol
net/hsr/hsr_slave.c:38:18: got restricted __be16 [usertype] h_proto
net/hsr/hsr_slave.c:39:25: warning: restricted __be16 degrades to integer
net/hsr/hsr_slave.c:39:57: warning: restricted __be16 degrades to integer
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When all hsr slave interfaces are removed, hsr interface doesn't work.
At that moment, it's fine to remove an unused hsr interface automatically
for saving resources.
That's a common behavior of virtual interfaces.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hsr_dev_change_mtu(), the 'dev' and 'master->dev' pointer are
same. So, the 'master' variable and some code are unnecessary.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current hsr code, only 0 and 1 protocol versions are valid.
But current hsr code doesn't check the version, which is received by
userspace.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1 version 4
In the test commands, version 4 is invalid.
So, the command should be failed.
After this patch, following error will occur.
"Error: hsr: Only versions 0..1 are supported."
Fixes: ee1c279772 ("net/hsr: Added support for HSR v1")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The port->hsr is used in the hsr_handle_frame(), which is a
callback of rx_handler.
hsr master and slaves are initialized in hsr_add_port().
This function initializes several pointers, which includes port->hsr after
registering rx_handler.
So, in the rx_handler routine, un-initialized pointer would be used.
In order to fix this, pointers should be initialized before
registering rx_handler.
Test commands:
ip netns del left
ip netns del right
modprobe -rv veth
modprobe -rv hsr
killall ping
modprobe hsr
ip netns add left
ip netns add right
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link add veth4 type veth peer name veth5
ip link set veth1 netns left
ip link set veth3 netns right
ip link set veth4 netns left
ip link set veth5 netns right
ip link set veth0 up
ip link set veth2 up
ip link set veth0 address fc:00:00:00:00:01
ip link set veth2 address fc:00:00:00:00:02
ip netns exec left ip link set veth1 up
ip netns exec left ip link set veth4 up
ip netns exec right ip link set veth3 up
ip netns exec right ip link set veth5 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec left ip link add hsr1 type hsr slave1 veth1 slave2 veth4
ip netns exec left ip a a 192.168.100.2/24 dev hsr1
ip netns exec left ip link set hsr1 up
ip netns exec left ip n a 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
ip netns exec left ip n r 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
for i in {1..100}
do
ip netns exec left ping 192.168.100.1 &
done
ip netns exec left hping3 192.168.100.1 -2 --flood &
ip netns exec right ip link add hsr2 type hsr slave1 veth3 slave2 veth5
ip netns exec right ip a a 192.168.100.3/24 dev hsr2
ip netns exec right ip link set hsr2 up
ip netns exec right ip n a 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
ip netns exec right ip n r 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
for i in {1..100}
do
ip netns exec right ping 192.168.100.1 &
done
ip netns exec right hping3 192.168.100.1 -2 --flood &
while :
do
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip link del hsr0
done
Splat looks like:
[ 120.954938][ C0] general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1]I
[ 120.957761][ C0] KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
[ 120.959064][ C0] CPU: 0 PID: 1511 Comm: hping3 Not tainted 5.6.0-rc5+ #460
[ 120.960054][ C0] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 120.962261][ C0] RIP: 0010:hsr_addr_is_self+0x65/0x2a0 [hsr]
[ 120.963149][ C0] Code: 44 24 18 70 73 2f c0 48 c1 eb 03 48 8d 04 13 c7 00 f1 f1 f1 f1 c7 40 04 00 f2 f2 f2 4
[ 120.966277][ C0] RSP: 0018:ffff8880d9c09af0 EFLAGS: 00010206
[ 120.967293][ C0] RAX: 0000000000000006 RBX: 1ffff1101b38135f RCX: 0000000000000000
[ 120.968516][ C0] RDX: dffffc0000000000 RSI: ffff8880d17cb208 RDI: 0000000000000000
[ 120.969718][ C0] RBP: 0000000000000030 R08: ffffed101b3c0e3c R09: 0000000000000001
[ 120.972203][ C0] R10: 0000000000000001 R11: ffffed101b3c0e3b R12: 0000000000000000
[ 120.973379][ C0] R13: ffff8880aaf80100 R14: ffff8880aaf800f2 R15: ffff8880aaf80040
[ 120.974410][ C0] FS: 00007f58e693f740(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[ 120.979794][ C0] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 120.980773][ C0] CR2: 00007ffcb8b38f29 CR3: 00000000afe8e001 CR4: 00000000000606f0
[ 120.981945][ C0] Call Trace:
[ 120.982411][ C0] <IRQ>
[ 120.982848][ C0] ? hsr_add_node+0x8c0/0x8c0 [hsr]
[ 120.983522][ C0] ? rcu_read_lock_held+0x90/0xa0
[ 120.984159][ C0] ? rcu_read_lock_sched_held+0xc0/0xc0
[ 120.984944][ C0] hsr_handle_frame+0x1db/0x4e0 [hsr]
[ 120.985597][ C0] ? hsr_nl_nodedown+0x2b0/0x2b0 [hsr]
[ 120.986289][ C0] __netif_receive_skb_core+0x6bf/0x3170
[ 120.992513][ C0] ? check_chain_key+0x236/0x5d0
[ 120.993223][ C0] ? do_xdp_generic+0x1460/0x1460
[ 120.993875][ C0] ? register_lock_class+0x14d0/0x14d0
[ 120.994609][ C0] ? __netif_receive_skb_one_core+0x8d/0x160
[ 120.995377][ C0] __netif_receive_skb_one_core+0x8d/0x160
[ 120.996204][ C0] ? __netif_receive_skb_core+0x3170/0x3170
[ ... ]
Reported-by: syzbot+fcf5dd39282ceb27108d@syzkaller.appspotmail.com
Fixes: c5a7591172 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hsr module has been supporting the list and status command.
(HSR_C_GET_NODE_LIST and HSR_C_GET_NODE_STATUS)
These commands send node information to the user-space via generic netlink.
But, in the non-init_net namespace, these commands are not allowed
because .netnsok flag is false.
So, there is no way to get node information in the non-init_net namespace.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hsr_get_node_list() is to send node addresses to the userspace.
If there are so many nodes, it could fail because of buffer size.
In order to avoid this failure, the restart routine is added.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_get_node_{list/status}() are not under rtnl_lock() because
they are callback functions of generic netlink.
But they use __dev_get_by_index() without rtnl_lock().
So, it would use unsafe data.
In order to fix it, rcu_read_lock() and dev_get_by_index_rcu()
are used instead of __dev_get_by_index().
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit e0a4b99773 ("hsr: use upper/lower device infrastructure"),
dev_get() was removed but dev_put() in the error path wasn't removed.
So, if creating hsr interface command is failed, the reference counter leak
of lower interface would occur.
Test commands:
ip link add dummy0 type dummy
ip link add ipvlan0 link dummy0 type ipvlan mode l2
ip link add ipvlan1 link dummy0 type ipvlan mode l2
ip link add hsr0 type hsr slave1 ipvlan0 slave2 ipvlan1
ip link del ipvlan0
Result:
[ 633.271992][ T1280] unregister_netdevice: waiting for ipvlan0 to become free. Usage count = -1
Fixes: e0a4b99773 ("hsr: use upper/lower device infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_upper_dev_link() is useful to manage lower/upper interfaces.
And this function internally validates looping, maximum depth.
All or most virtual interfaces that could have a real interface
(e.g. macsec, macvlan, ipvlan etc.) use lower/upper infrastructure.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to access the port list, the hsr_port_get_hsr() is used.
And this is protected by RTNL and RCU.
The hsr_fill_info(), hsr_check_carrier(), hsr_dev_open() and
hsr_get_max_mtu() are protected by RTNL.
So, rcu_read_lock() in these functions are not necessary.
The hsr_handle_frame() also uses rcu_read_lock() but this function
is called by packet path.
It's already protected by RCU.
So, the rcu_read_lock() in hsr_handle_frame() can be removed.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When HSR interface is sending a frame, it finds a node with
the destination ethernet address from the list.
If there is no node, it calls WARN_ONCE().
But, using WARN_ONCE() for this situation is a little bit overdoing.
So, in this patch, the netdev_err() is used instead.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If HSR uses the extack instead of netdev_info(), users can get
error messages immediately without any checking the kernel message.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If it uses debugfs_remove_recursive() instead of debugfs_remove(),
hsr_priv() doesn't need to have "node_tbl_file" pointer variable.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
node_db is traversed using list_for_each_entry_rcu
outside an RCU read-side critical section but under the protection
of hsr->list_lock.
Hence, add corresponding lockdep expression to silence false-positive
warnings, and harden RCU lists.
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's never used after introduced. So maybe better to remove.
Signed-off-by: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Arvid Brodin <arvid.brodin@alten.se>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The hsr_debugfs_rename prototype got an extra 'void' that needs to
be removed again:
In file included from /git/arm-soc/net/hsr/hsr_main.c:12:
net/hsr/hsr_main.h:194:20: error: two or more data types in declaration specifiers
static inline void void hsr_debugfs_rename(struct net_device *dev)
Fixes: 4c2d5e33dc ("hsr: rename debugfs file when interface name is changed")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The supervision frame is L2 frame.
When supervision frame is created, hsr module doesn't set network header.
If tap routine is enabled, dev_queue_xmit_nit() is called and it checks
network_header. If network_header pointer wasn't set(or invalid),
it resets network_header and warns.
In order to avoid unnecessary warning message, resetting network_header
is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
tcpdump -nei veth0
Splat looks like:
[ 175.852292][ C3] protocol 88fb is buggy, dev veth0
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr nodes are protected by RCU and there is no write side lock.
But node insertions and deletions could be being operated concurrently.
So write side locking is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
for i in {0..9}
do
for j in {0..9}
do
for k in {0..9}
do
for l in {0..9}
do
arping 192.168.100.2 -I hsr0 -s 00:01:3$i:4$j:5$k:6$l -c1 &
done
done
done
done
Splat looks like:
[ 236.066091][ T3286] list_add corruption. next->prev should be prev (ffff8880a5940300), but was ffff8880a5940d0.
[ 236.069617][ T3286] ------------[ cut here ]------------
[ 236.070545][ T3286] kernel BUG at lib/list_debug.c:25!
[ 236.071391][ T3286] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 236.072343][ T3286] CPU: 0 PID: 3286 Comm: arping Tainted: G W 5.5.0-rc1+ #209
[ 236.073463][ T3286] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 236.074695][ T3286] RIP: 0010:__list_add_valid+0x74/0xd0
[ 236.075499][ T3286] Code: 48 39 da 75 27 48 39 f5 74 36 48 39 dd 74 31 48 83 c4 08 b8 01 00 00 00 5b 5d c3 48 b
[ 236.078277][ T3286] RSP: 0018:ffff8880aaa97648 EFLAGS: 00010286
[ 236.086991][ T3286] RAX: 0000000000000075 RBX: ffff8880d4624c20 RCX: 0000000000000000
[ 236.088000][ T3286] RDX: 0000000000000075 RSI: 0000000000000008 RDI: ffffed1015552ebf
[ 236.098897][ T3286] RBP: ffff88809b53d200 R08: ffffed101b3c04f9 R09: ffffed101b3c04f9
[ 236.099960][ T3286] R10: 00000000308769a1 R11: ffffed101b3c04f8 R12: ffff8880d4624c28
[ 236.100974][ T3286] R13: ffff8880d4624c20 R14: 0000000040310100 R15: ffff8880ce17ee02
[ 236.138967][ T3286] FS: 00007f23479fa680(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[ 236.144852][ T3286] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 236.145720][ T3286] CR2: 00007f4a14bab210 CR3: 00000000a61c6001 CR4: 00000000000606f0
[ 236.146776][ T3286] Call Trace:
[ 236.147222][ T3286] hsr_add_node+0x314/0x490 [hsr]
[ 236.153633][ T3286] hsr_forward_skb+0x2b6/0x1bc0 [hsr]
[ 236.154362][ T3286] ? rcu_read_lock_sched_held+0x90/0xc0
[ 236.155091][ T3286] ? rcu_read_lock_bh_held+0xa0/0xa0
[ 236.156607][ T3286] hsr_dev_xmit+0x70/0xd0 [hsr]
[ 236.157254][ T3286] dev_hard_start_xmit+0x160/0x740
[ 236.157941][ T3286] __dev_queue_xmit+0x1961/0x2e10
[ 236.158565][ T3286] ? netdev_core_pick_tx+0x2e0/0x2e0
[ ... ]
Reported-by: syzbot+3924327f9ad5f4d2b343@syzkaller.appspotmail.com
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr interface has own debugfs file, which name is same with interface name.
So, interface name is changed, debugfs file name should be changed too.
Fixes: fc4ecaeebd ("net: hsr: add debugfs support for display node list")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current hsr code, when hsr interface is created, it creates debugfs
directory /sys/kernel/debug/<interface name>.
If there is same directory or file name in there, it fails.
In order to reduce possibility of failure of creation of debugfs,
this patch adds root directory.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
Before this patch:
/sys/kernel/debug/hsr0/node_table
After this patch:
/sys/kernel/debug/hsr/hsr0/node_table
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_dev_finalize() is called to create new hsr interface.
There are some wrong error handling codes.
1. wrong checking return value of debugfs_create_{dir/file}.
These function doesn't return NULL. If error occurs in there,
it returns error pointer.
So, it should check error pointer instead of NULL.
2. It doesn't unregister interface if it fails to setup hsr interface.
If it fails to initialize hsr interface after register_netdevice(),
it should call unregister_netdevice().
3. Ignore failure of creation of debugfs
If creating of debugfs dir and file is failed, creating hsr interface
will be failed. But debugfs doesn't affect actual logic of hsr module.
So, ignoring this is more correct and this behavior is more general.
Fixes: c5a7591172 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switching from ->priv_destructor to dellink() has an unexpected
consequence: existing RCU readers, that is, hsr_port_get_hsr()
callers, may still be able to read the port list.
Instead of checking the return value of each hsr_port_get_hsr(),
we can just move it to ->ndo_uninit() which is called after
device unregister and synchronize_net(), and we still have RTNL
lock there.
Fixes: b9a1e62740 ("hsr: implement dellink to clean up resources")
Fixes: edf070a0fb ("hsr: fix a NULL pointer deref in hsr_dev_xmit()")
Reported-by: syzbot+097ef84cdc95843fbaa8@syzkaller.appspotmail.com
Cc: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_link_ops implements ->newlink() but not ->dellink(),
which leads that resources not released after removing the device,
particularly the entries in self_node_db and node_db.
So add ->dellink() implementation to replace the priv_destructor.
This also makes the code slightly easier to understand.
Reported-by: syzbot+c6167ec3de7def23d1e8@syzkaller.appspotmail.com
Cc: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_del_port() should release all the resources allocated
in hsr_add_port().
As a consequence of this change, hsr_for_each_port() is no
longer safe to work with hsr_del_port(), switch to
list_for_each_entry_safe() as we always hold RTNL lock.
Cc: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't prune the master node in the hsr_prune_nodes function.
Neither time_in[HSR_PT_SLAVE_A] nor time_in[HSR_PT_SLAVE_B]
will ever be updated by hsr_register_frame_in for the master port.
Thus, the master node will be repeatedly pruned leading to
repeated packet loss.
This bug never appeared because the hsr_prune_nodes function
was only called once. Since commit 5150b45fd3
("net: hsr: Fix node prune function for forget time expiry") this issue
is fixed unveiling the issue described above.
Fixes: 5150b45fd3 ("net: hsr: Fix node prune function for forget time expiry")
Signed-off-by: Andreas Oetken <andreas.oetken@siemens.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add options to strictly validate messages and dump messages,
sometimes perhaps validating dump messages non-strictly may
be required, so add an option for that as well.
Since none of this can really be applied to existing commands,
set the options everwhere using the following spatch:
@@
identifier ops;
expression X;
@@
struct genl_ops ops[] = {
...,
{
.cmd = X,
+ .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
...
},
...
};
For new commands one should just not copy the .validate 'opt-out'
flags and thus get strict validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tx stats to hsr interface. Without this
ifconfig for hsr interface doesn't show tx packet stats.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the path of hsr debugfs root directory to use the net device
name so that it can work with multiple interfaces. While at it,
also fix some typos.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the file name and functions to match with existing implementation.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
