When hds-thresh is configured, ethnl_set_rings() is called, and it calls
ethtool_ringparam_get_cfg() to get ringparameters from .get_ringparam()
callback and dev->cfg.
Both hds_config and hds_thresh values should be set from dev->cfg, not
from .get_ringparam().
But ethtool_ringparam_get_cfg() sets only hds_config from dev->cfg.
So, ethtool_ringparam_get_cfg() returns always a hds_thresh as 0.
If an input value of hds-thresh is 0, a hds_thresh value from
ethtool_ringparam_get_cfg() are same. So ethnl_set_rings() does
nothing and returns immediately.
It causes a bug that setting a hds-thresh value to 0 is not working.
Reproducer:
modprobe netdevsim
echo 1 > /sys/bus/netdevsim/new_device
ethtool -G eth0 hds-thresh 100
ethtool -G eth0 hds-thresh 0
ethtool -g eth0
#hds-thresh value should be 0, but it shows 100.
The tools/testing/selftests/drivers/net/hds.py can test it too with
applying a following patch for hds.py.
Fixes: 928459bbda ("net: ethtool: populate the default HDS params in the core")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20250404122126.1555648-2-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add SOF_TIMESTAMPING_TX_COMPLETION, for requesting a software timestamp
when hardware reports a packet completed.
Completion tstamp is useful for Bluetooth, as hardware timestamps do not
exist in the HCI specification except for ISO packets, and the hardware
has a queue where packets may wait. In this case the software SND
timestamp only reflects the kernel-side part of the total latency
(usually small) and queue length (usually 0 unless HW buffers
congested), whereas the completion report time is more informative of
the true latency.
It may also be useful in other cases where HW TX timestamps cannot be
obtained and user wants to estimate an upper bound to when the TX
probably happened.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
link_mode_params contains a lookup table of all 802.3 link modes that
are currently supported with structured data about each mode's speed,
duplex, number of lanes and mediums.
As a preparation for a port representation, export that table for the
rest of the net stack to use.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-2-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Handling the CWR flag differs between RFC 3168 ECN and AccECN.
With RFC 3168 ECN aware TSO (NETIF_F_TSO_ECN) CWR flag is cleared
starting from 2nd segment which is incompatible how AccECN handles
the CWR flag. Such super-segments are indicated by SKB_GSO_TCP_ECN.
With AccECN, CWR flag (or more accurately, the ACE field that also
includes ECE & AE flags) changes only when new packet(s) with CE
mark arrives so the flag should not be changed within a super-skb.
The new skb/feature flags are necessary to prevent such TSO engines
corrupting AccECN ACE counters by clearing the CWR flag (if the
CWR handling feature cannot be turned off).
If NIC is completely unaware of RFC3168 ECN (doesn't support
NETIF_F_TSO_ECN) or its TSO engine can be set to not touch CWR flag
despite supporting also NETIF_F_TSO_ECN, TSO could be safely used
with AccECN on such NIC. This should be evaluated per NIC basis
(not done in this patch series for any NICs).
For the cases, where TSO cannot keep its hands off the CWR flag,
a GSO fallback is provided by this patch.
Signed-off-by: Ilpo Järvinen <ij@kernel.org>
Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
tools/testing/selftests/drivers/net/ping.py
75cc19c8ff ("selftests: drv-net: add xdp cases for ping.py")
de94e86974 ("selftests: drv-net: store addresses in dict indexed by ipver")
https://lore.kernel.org/netdev/20250311115758.17a1d414@canb.auug.org.au/
net/core/devmem.c
a70f891e0f ("net: devmem: do not WARN conditionally after netdev_rx_queue_restart()")
1d22d3060b ("net: drop rtnl_lock for queue_mgmt operations")
https://lore.kernel.org/netdev/20250313114929.43744df1@canb.auug.org.au/
Adjacent changes:
tools/testing/selftests/net/Makefile
6f50175cca ("selftests: Add IPv6 link-local address generation tests for GRE devices.")
2e5584e0f9 ("selftests/net: expand cmsg_ipv6.sh with ipv4")
drivers/net/ethernet/broadcom/bnxt/bnxt.c
661958552e ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic")
fe96d717d3 ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix missing initialization of ts_info->phc_index in the dump command,
which could cause a netdev interface to incorrectly display a PTP provider
at index 0 instead of "none".
Fix it by initializing the phc_index to -1.
In the same time, restore missing initialization of ts_info.cmd for the
IOCTL case, as it was before the transition from ethnl_default_dumpit to
custom ethnl_tsinfo_dumpit.
Also, remove unnecessary zeroing of ts_info, as it is embedded within
reply_data, which is fully zeroed two lines earlier.
Fixes: b9e3f7dc9e ("net: ethtool: tsinfo: Enhance tsinfo to support several hwtstamp by net topology")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250307091255.463559-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the more esoteric helpers for netdev instance lock to
a dedicated header. This avoids growing netdevice.h to infinity
and makes rebuilding the kernel much faster (after touching
the header with the helpers).
The main netdev_lock() / netdev_unlock() functions are used
in static inlines in netdevice.h and will probably be used
most commonly, so keep them in netdevice.h.
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250307183006.2312761-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
net/ethtool/cabletest.c
2bcf4772e4 ("net: ethtool: try to protect all callback with netdev instance lock")
637399bf7e ("net: ethtool: netlink: Allow NULL nlattrs when getting a phy_device")
No Adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Protect all ethtool callbacks and PHY related state with the netdev
instance lock, for drivers which want / need to have their ops
instance-locked. Basically take the lock everywhere we take rtnl_lock.
It was tempting to take the lock in ethnl_ops_begin(), but turns
out we actually nest those calls (when generating notifications).
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Saeed Mahameed <saeed@kernel.org>
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250305163732.2766420-11-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ethnl_req_get_phydev() is used to lookup a phy_device, in the case an
ethtool netlink command targets a specific phydev within a netdev's
topology.
It takes as a parameter a const struct nlattr *header that's used for
error handling :
if (!phydev) {
NL_SET_ERR_MSG_ATTR(extack, header,
"no phy matching phyindex");
return ERR_PTR(-ENODEV);
}
In the notify path after a ->set operation however, there's no request
attributes available.
The typical callsite for the above function looks like:
phydev = ethnl_req_get_phydev(req_base, tb[ETHTOOL_A_XXX_HEADER],
info->extack);
So, when tb is NULL (such as in the ethnl notify path), we have a nice
crash.
It turns out that there's only the PLCA command that is in that case, as
the other phydev-specific commands don't have a notification.
This commit fixes the crash by passing the cmd index and the nlattr
array separately, allowing NULL-checking it directly inside the helper.
Fixes: c15e065b46 ("net: ethtool: Allow passing a phy index for some commands")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Reported-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20250301141114.97204-1-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The legacy ioctl path does not have support for extended attributes.
So we issue a GET to fetch the current settings from the driver,
in an attempt to keep them unchanged. HDS is a bit "special" as
the GET only returns on/off while the SET takes a "ternary" argument
(on/off/default). If the driver was in the "default" setting -
executing the ioctl path binds it to on or off, even tho the user
did not intend to change HDS config.
Factor the relevant logic out of the netlink code and reuse it.
Fixes: 87c8f8496a ("bnxt_en: add support for tcp-data-split ethtool command")
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Tested-by: Daniel Xu <dxu@dxuuu.xyz>
Tested-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20250221025141.1132944-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 42dc431f5d ("ethtool: rss: prevent rss ctx deletion
when in use") we prevent removal of RSS contexts pointed to by
existing flow rules. Core should also prevent creation of rules
which point to RSS context which don't exist in the first place.
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20250206235334.1425329-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the netlink type for hardware timestamp flags, which are represented
as a bitset of flags. Although only one flag is supported currently, the
correct netlink bitset type should be used instead of u32 to keep
consistency with other fields. Address this by adding a new named string
set description for the hwtstamp flag structure.
The code has been introduced in the current release so the uAPI change is
still okay.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Fixes: 6e9e2eed4f ("net: ethtool: Add support for tsconfig command to get/set hwtstamp config")
Link: https://patch.msgid.link/20250205110304.375086-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define 200G, 400G and 800G link modes using 200Gbps per lane.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The info.flow_type is for RXFH commands, ntuple flow_type is inside
the flow spec. The check currently does nothing, as info.flow_type
is 0 (or even uninitialized by user space) for ETHTOOL_SRXCLSRLINS.
Fixes: 9e43ad7a1e ("net: ethtool: only allow set_rxnfc with rss + ring_cookie if driver opts in")
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20250201013040.725123-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit ec6e57beaf ("ethtool: rss: don't report key if device
doesn't support it") intended to stop reporting key fields for
additional rss contexts if device has a global hashing key.
Later we added dump support and the filtering wasn't properly
added there. So we end up reporting the key fields in dumps
but not in dos:
# ./pyynl/cli.py --spec netlink/specs/ethtool.yaml --do rss-get \
--json '{"header": {"dev-index":2}, "context": 1 }'
{
"header": { ... },
"context": 1,
"indir": [0, 1, 2, 3, ...]]
}
# ./pyynl/cli.py --spec netlink/specs/ethtool.yaml --dump rss-get
[
... snip context 0 ...
{ "header": { ... },
"context": 1,
"indir": [0, 1, 2, 3, ...],
-> "input_xfrm": 255,
-> "hfunc": 1,
-> "hkey": "000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000"
}
]
Hide these fields correctly.
The drivers/net/hw/rss_ctx.py selftest catches this when run on
a device with single key, already:
# Check| At /root/./ksft-net-drv/drivers/net/hw/rss_ctx.py, line 381, in test_rss_context_dump:
# Check| ksft_ne(set(data.get('hkey', [1])), {0}, "key is all zero")
# Check failed {0} == {0} key is all zero
not ok 8 rss_ctx.test_rss_context_dump
Fixes: f6122900f4 ("ethtool: rss: support dumping RSS contexts")
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20250201013040.725123-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sanity check that both source and destination are set when symmetric
RSS hash is requested is only relevant for ETHTOOL_SRXFH (rx-flow-hash),
it should not be performed on any other commands (e.g.
ETHTOOL_SRXCLSRLINS/ETHTOOL_SRXCLSRLDEL).
This resolves accessing uninitialized 'info.data' field, and fixes false
errors in rule insertion:
# ethtool --config-ntuple eth2 flow-type ip4 dst-ip 255.255.255.255 action -1 loc 0
rmgr: Cannot insert RX class rule: Invalid argument
Cannot insert classification rule
Fixes: 13e59344fb ("net: ethtool: add support for symmetric-xor RSS hash")
Cc: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://patch.msgid.link/20250126191845.316589-1-gal@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The core has the current HDS config, it can pre-populate the values
for the drivers. While at it, remove the zero-setting in netdevsim.
Zero are the default values since the config is zalloc'ed.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250119020518.1962249-6-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Record the pending configuration in net_device struct.
ethtool core duplicates the current config and the specific
handlers (for now just ringparam) can modify it.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250119020518.1962249-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For ease of review of the next patch store the dev pointer
on the stack, instead of referring to req_info.dev every time.
No functional changes.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250119020518.1962249-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Separate the HDS config from the ethtool state struct.
The HDS config contains just simple parameters, not state.
Having it as a separate struct will make it easier to clone / copy
and also long term potentially make it per-queue.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250119020518.1962249-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following trace can be seen if a device is being unregistered while
its number of channels are being modified.
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 3 PID: 3754 at kernel/locking/mutex.c:564 __mutex_lock+0xc8a/0x1120
CPU: 3 UID: 0 PID: 3754 Comm: ethtool Not tainted 6.13.0-rc6+ #771
RIP: 0010:__mutex_lock+0xc8a/0x1120
Call Trace:
<TASK>
ethtool_check_max_channel+0x1ea/0x880
ethnl_set_channels+0x3c3/0xb10
ethnl_default_set_doit+0x306/0x650
genl_family_rcv_msg_doit+0x1e3/0x2c0
genl_rcv_msg+0x432/0x6f0
netlink_rcv_skb+0x13d/0x3b0
genl_rcv+0x28/0x40
netlink_unicast+0x42e/0x720
netlink_sendmsg+0x765/0xc20
__sys_sendto+0x3ac/0x420
__x64_sys_sendto+0xe0/0x1c0
do_syscall_64+0x95/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
This is because unregister_netdevice_many_notify might run before the
rtnl lock section of ethnl operations, eg. set_channels in the above
example. In this example the rss lock would be destroyed by the device
unregistration path before being used again, but in general running
ethnl operations while dismantle has started is not a good idea.
Fix this by denying any operation on devices being unregistered. A check
was already there in ethnl_ops_begin, but not wide enough.
Note that the same issue cannot be seen on the ioctl version
(__dev_ethtool) because the device reference is retrieved from within
the rtnl lock section there. Once dismantle started, the net device is
unlisted and no reference will be found.
Fixes: dde91ccfa2 ("ethtool: do not perform operations on net devices being unregistered")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20250116092159.50890-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For packets with two-step timestamp requests, the hardware timestamp
comes back to the driver through a confirmation mechanism of sorts,
which allows the driver to confidently bump the successful "pkts"
counter.
For one-step PTP, the NIC is supposed to autonomously insert its
hardware TX timestamp in the packet headers while simultaneously
transmitting it. There may be a confirmation that this was done
successfully, or there may not.
None of the current drivers which implement ethtool_ops :: get_ts_stats()
also support HWTSTAMP_TX_ONESTEP_SYNC or HWTSTAMP_TX_ONESTEP_SYNC, so it
is a bit unclear which model to follow. But there are NICs, such as DSA,
where there is no transmit confirmation at all. Here, it would be wrong /
misleading to increment the successful "pkts" counter, because one-step
PTP packets can be dropped on TX just like any other packets.
So introduce a special counter which signifies "yes, an attempt was made,
but we don't know whether it also exited the port or not". I expect that
for one-step PTP packets where a confirmation is available, the "pkts"
counter would be bumped.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250116104628.123555-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While the devmem is running, the tcp-data-split and
hds-thresh configuration should not be changed.
If user tries to change tcp-data-split and threshold value while the
devmem is running, it fails and shows extack message.
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20250114142852.3364986-5-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hds-thresh option configures the threshold value of
the header-data-split.
If a received packet size is larger than this threshold value, a packet
will be split into header and payload.
The header indicates TCP and UDP header, but it depends on driver spec.
The bnxt_en driver supports HDS(Header-Data-Split) configuration at
FW level, affecting TCP and UDP too.
So, If hds-thresh is set, it affects UDP and TCP packets.
Example:
# ethtool -G <interface name> hds-thresh <value>
# ethtool -G enp14s0f0np0 tcp-data-split on hds-thresh 256
# ethtool -g enp14s0f0np0
Ring parameters for enp14s0f0np0:
Pre-set maximums:
...
HDS thresh: 1023
Current hardware settings:
...
TCP data split: on
HDS thresh: 256
The default/min/max values are not defined in the ethtool so the drivers
should define themself.
The 0 value means that all TCP/UDP packets' header and payload
will be split.
Tested-by: Stanislav Fomichev <sdf@fomichev.me>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20250114142852.3364986-3-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When tcp-data-split is UNKNOWN mode, drivers arbitrarily handle it.
For example, bnxt_en driver automatically enables if at least one of
LRO/GRO/JUMBO is enabled.
If tcp-data-split is UNKNOWN and LRO is enabled, a driver returns
ENABLES of tcp-data-split, not UNKNOWN.
So, `ethtool -g eth0` shows tcp-data-split is enabled.
The problem is in the setting situation.
In the ethnl_set_rings(), it first calls get_ringparam() to get the
current driver's config.
At that moment, if driver's tcp-data-split config is UNKNOWN, it returns
ENABLE if LRO/GRO/JUMBO is enabled.
Then, it sets values from the user and driver's current config to
kernel_ethtool_ringparam.
Last it calls .set_ringparam().
The driver, especially bnxt_en driver receives
ETHTOOL_TCP_DATA_SPLIT_ENABLED.
But it can't distinguish whether it is set by the user or just the
current config.
When user updates ring parameter, the new hds_config value is updated
and current hds_config value is stored to old_hdsconfig.
Driver's .set_ringparam() callback can distinguish a passed
tcp-data-split value is came from user explicitly.
If .set_ringparam() is failed, hds_config is rollbacked immediately.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20250114142852.3364986-2-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ethtool_get_status callback currently handles all status and PSE
information within a single function. This approach has two key
drawbacks:
1. If the core requires some information for purposes other than
ethtool_get_status, redundant code will be needed to fetch the same
data from the driver (like is_enabled).
2. Drivers currently have access to all information passed to ethtool.
New variables will soon be added to ethtool status, such as PSE ID,
power domain IDs, and budget evaluation strategies, which are meant
to be managed solely by the core. Drivers should not have the ability
to modify these variables.
To resolve these issues, ethtool_get_status has been split into multiple
callbacks, with each handling a specific piece of information required
by ethtool or the core.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce a new way to report PHY statistics in a structured and
standardized format using the netlink API. This new method does not
replace the old driver-specific stats, which can still be accessed with
`ethtool -S <eth name>`. The structured stats are available with
`ethtool -S <eth name> --all-groups`.
This new method makes it easier to diagnose problems by organizing stats
in a consistent and documented way.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce support for standardized PHY statistics reporting in ethtool
by extending the PHYLIB framework. Add the functions
phy_ethtool_get_phy_stats() and phy_ethtool_get_link_ext_stats() to
provide a consistent interface for retrieving PHY-level and
link-specific statistics. These functions are used within the ethtool
implementation to avoid direct access to the phy_device structure
outside of the PHYLIB framework.
A new structure, ethtool_phy_stats, is introduced to standardize PHY
statistics such as packet counts, byte counts, and error counters.
Drivers are updated to include callbacks for retrieving PHY and
link-specific statistics, ensuring values are explicitly set only for
supported fields, initialized with ETHTOOL_STAT_NOT_SET to avoid
ambiguity.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Adapt linkstate_get_sqi() and linkstate_get_sqi_max() to take a
phy_device argument directly, enabling support for setups with
multiple PHYs. The previous assumption of a single PHY attached to
a net_device no longer holds.
Use ethnl_req_get_phydev() to identify the appropriate PHY device
for the operation. Update linkstate_prepare_data() and related
logic to accommodate this change, ensuring compatibility with
multi-PHY configurations.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
hwprov should be protected by rcu_read_lock to prevent possible UAF
Fixes: 4c61d809cf ("net: ethtool: Fix suspicious rcu_dereference usage")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
diff with v1: move and use err varialbe, instead of define a new variable
net/ethtool/common.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
Link: https://patch.msgid.link/20250109111057.4746-1-lirongqing@baidu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce support for ETHTOOL_MSG_TSCONFIG_GET/SET ethtool netlink socket
to read and configure hwtstamp configuration of a PHC provider. Note that
simultaneous hwtstamp isn't supported; configuring a new one disables the
previous setting.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Either the MAC or the PHY can provide hwtstamp, so we should be able to
read the tsinfo for any hwtstamp provider.
Enhance 'get' command to retrieve tsinfo of hwtstamp providers within a
network topology.
Add support for a specific dump command to retrieve all hwtstamp
providers within the network topology, with added functionality for
filtered dump to target a single interface.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bitset without mask in a _SET request means we want exactly the bits in
the bitset to be set. This works correctly for compact format but when
verbose format is parsed, ethnl_update_bitset32_verbose() only sets the
bits present in the request bitset but does not clear the rest. The commit
6699170376 ("ethtool: fix application of verbose no_mask bitset") fixes
this issue by clearing the whole target bitmap before we start iterating.
The solution proposed brought an issue with the behavior of the mod
variable. As the bitset is always cleared the old value will always
differ to the new value.
Fix it by adding a new function to compare bitmaps and a temporary variable
which save the state of the old bitmap.
Fixes: 6699170376 ("ethtool: fix application of verbose no_mask bitset")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20241202153358.1142095-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The check for non-zero ring with RSS is only relevant for
ETHTOOL_SRXCLSRLINS command, in other cases the check tries to access
memory which was not initialized by the userspace tool. Only perform the
check in case of ETHTOOL_SRXCLSRLINS.
Without this patch, filter deletion (for example) could statistically
result in a false error:
# ethtool --config-ntuple eth3 delete 484
rmgr: Cannot delete RX class rule: Invalid argument
Cannot delete classification rule
Fixes: 9e43ad7a1e ("net: ethtool: only allow set_rxnfc with rss + ring_cookie if driver opts in")
Link: https://lore.kernel.org/netdev/871a9ecf-1e14-40dd-bbd7-e90c92f89d47@nvidia.com/
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20241202164805.1637093-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ethtool_check_max_channel(), the new RX count must not only cover the
max queue indices in RSS indirection tables and RXNFC destinations
separately, but must also, for RXNFC rules with FLOW_RSS, cover the sum
of the destination queue and the maximum index in the associated RSS
context's indirection table, since that is the highest queue that the
rule can actually deliver traffic to.
It could be argued that the max queue across all custom RSS contexts
(ethtool_get_max_rss_ctx_channel()) need no longer be considered, since
any context to which packets can actually be delivered will be targeted
by some RXNFC rule and its max will thus be allowed for by
ethtool_get_max_rxnfc_channel(). For simplicity we keep both checks, so
even RSS contexts unused by any RXNFC rule must fit the channel count.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/43257d375434bef388e36181492aa4c458b88336.1731499022.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ethtool ntuple filters with FLOW_RSS were originally defined as adding
the base queue ID (ring_cookie) to the value from the indirection table,
so that the same table could distribute over more than one set of queues
when used by different filters.
However, some drivers / hardware ignore the ring_cookie, and simply use
the indirection table entries as queue IDs directly. Thus, for drivers
which have not opted in by setting ethtool_ops.cap_rss_rxnfc_adds to
declare that they support the original (addition) semantics, reject in
ethtool_set_rxnfc any filter which combines FLOW_RSS and a nonzero ring.
(For a ring_cookie of zero, both behaviours are equivalent.)
Set the cap bit in sfc, as it is known to support this feature.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://patch.msgid.link/cc3da0844083b0e301a33092a6299e4042b65221.1731499022.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
Change the type of the middle struct member currently causing trouble from
`struct ethtool_link_settings` to `struct ethtool_link_settings_hdr`.
Additionally, update the type of some variables in various functions that
don't access the flexible-array member, changing them to the newly created
`struct ethtool_link_settings_hdr`. These changes are needed because the
type of the conflicting middle members changed. So, those instances that
expect the type to be `struct ethtool_link_settings` should be adjusted to
the newly created type `struct ethtool_link_settings_hdr`.
Also, adjust variable declarations to follow the reverse xmas tree
convention.
Fix 3338 of the following -Wflex-array-member-not-at-end warnings:
include/linux/ethtool.h:214:38: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/0bc2809fe2a6c11dd4c8a9a10d9bd65cccdb559b.1730238285.git.gustavoars@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ntuple filters can specify an rss context to use for packet hashing
and queue selection. When a filter is referencing an rss context, it
should be invalid for that context to be deleted. A list of active
ntuple filters and their associated rss contexts can be compiled by
querying a device's ethtool_ops.get_rxnfc. This patch checks to see if
any ntuple filters are referencing an rss context during context
deletion, and prevents the deletion if the requested context is still
in use.
Signed-off-by: Daniel Zahka <daniel.zahka@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the CMIS specification for pluggable modules, LPL (Local Payload) and
EPL (Extended Payload) are two types of data payloads used for managing
various functions and features of the module.
EPL payloads are used for more complex and extensive management
functions that require a larger amount of data, so writing firmware
blocks using EPL is much more efficient.
Currently, only LPL payload is supported for writing firmware blocks to
the module.
Add support for writing firmware block using EPL payload, both to
support modules that supports only EPL write mechanism, and to optimize
the flashing process of modules that support LPL and EPL.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the CMIS specification for pluggable modules, LPL (Local Payload) and
EPL (Extended Payload) are two types of data payloads used for managing
various functions and features of the module.
EPL payloads are used for more complex and extensive management
functions that require a larger amount of data, so writing firmware
blocks using EPL is much more efficient.
Currently, only LPL payload is supported for writing firmware blocks to
the module.
Add EPL related parameters to the function ethtool_cmis_cdb_compose_args()
and add a specific function for calculating the maximum allowable length
extension for EPL. Both will be used in the next patch to add support for
writing firmware blocks using EPL.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows a more uniform implementation of non-dump and dump
operations, and will be used later in the series to avoid some
per-operation allocation.
Additionally rename the NL_ASSERT_DUMP_CTX_FITS macro, to
fit a more extended usage.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Link: https://patch.msgid.link/1130cc2896626b84587a2a5f96a5c6829638f4da.1728460186.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This warning is emitted when a driver does not default populate an rss
key when one is not provided from userspace. Some devices do not
support individual rss keys per context. For these devices, it is ok
to leave the key zeroed out in ethtool_rxfh_context. Do not warn on
zeroed key when ethtool_ops.rxfh_per_ctx_key == 0.
Signed-off-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20241003162310.1310576-1-daniel.zahka@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During the firmware flashing process, notifications are sent to user
space to provide progress updates. When an error occurs, an error
message is sent to indicate what went wrong.
In some cases, appropriate error messages are missing.
Add relevant error messages where applicable, allowing user space to better
understand the issues encountered.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240910091044.3044568-1-danieller@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a netdev_dmabuf_binding struct which represents the
dma-buf-to-netdevice binding. The netlink API will bind the dma-buf to
rx queues on the netdevice. On the binding, the dma_buf_attach
& dma_buf_map_attachment will occur. The entries in the sg_table from
mapping will be inserted into a genpool to make it ready
for allocation.
The chunks in the genpool are owned by a dmabuf_chunk_owner struct which
holds the dma-buf offset of the base of the chunk and the dma_addr of
the chunk. Both are needed to use allocations that come from this chunk.
We create a new type that represents an allocation from the genpool:
net_iov. We setup the net_iov allocation size in the
genpool to PAGE_SIZE for simplicity: to match the PAGE_SIZE normally
allocated by the page pool and given to the drivers.
The user can unbind the dmabuf from the netdevice by closing the netlink
socket that established the binding. We do this so that the binding is
automatically unbound even if the userspace process crashes.
The binding and unbinding leaves an indicator in struct netdev_rx_queue
that the given queue is bound, and the binding is actuated by resetting
the rx queue using the queue API.
The netdev_dmabuf_binding struct is refcounted, and releases its
resources only when all the refs are released.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Kaiyuan Zhang <kaiyuanz@google.com>
Signed-off-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com> # excluding netlink
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20240910171458.219195-4-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
introduce a new flag SOF_TIMESTAMPING_OPT_RX_FILTER in the receive
path. User can set it with SOF_TIMESTAMPING_SOFTWARE to filter
out rx software timestamp report, especially after a process turns on
netstamp_needed_key which can time stamp every incoming skb.
Previously, we found out if an application starts first which turns on
netstamp_needed_key, then another one only passing SOF_TIMESTAMPING_SOFTWARE
could also get rx timestamp. Now we handle this case by introducing this
new flag without breaking users.
Quoting Willem to explain why we need the flag:
"why a process would want to request software timestamp reporting, but
not receive software timestamp generation. The only use I see is when
the application does request
SOF_TIMESTAMPING_SOFTWARE | SOF_TIMESTAMPING_TX_SOFTWARE."
Similarly, this new flag could also be used for hardware case where we
can set it with SOF_TIMESTAMPING_RAW_HARDWARE, then we won't receive
hardware receive timestamp.
Another thing about errqueue in this patch I have a few words to say:
In this case, we need to handle the egress path carefully, or else
reporting the tx timestamp will fail. Egress path and ingress path will
finally call sock_recv_timestamp(). We have to distinguish them.
Errqueue is a good indicator to reflect the flow direction.
Suggested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240909015612.3856-2-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All devices support SOF_TIMESTAMPING_RX_SOFTWARE by virtue of
net_timestamp_check() being called in the device independent code.
Move the responsibility of reporting SOF_TIMESTAMPING_RX_SOFTWARE and
SOF_TIMESTAMPING_SOFTWARE, and setting PHC index to -1 to the core.
Device drivers no longer need to use them.
Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Link: https://lore.kernel.org/netdev/661550e348224_23a2b2294f7@willemb.c.googlers.com.notmuch/
Co-developed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240901112803.212753-2-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ability to handle maximum FCoE frames of 2158 bytes can never be changed
and thus more of an attribute, not a toggleable feature.
Move it from netdev_features_t to "cold" priv flags (bitfield bool) and
free yet another feature bit.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
"Interface can't change network namespaces" is rather an attribute,
not a feature, and it can't be changed via Ethtool.
Make it a "cold" private flag instead of a netdev_feature and free
one more bit.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
NETIF_F_LLTX can't be changed via Ethtool and is not a feature,
rather an attribute, very similar to IFF_NO_QUEUE (and hot).
Free one netdev_features_t bit and make it a "hot" private flag.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A sysfs reader can race with a device reset or removal, attempting to
read device state when the device is not actually present. eg:
[exception RIP: qed_get_current_link+17]
#8 [ffffb9e4f2907c48] qede_get_link_ksettings at ffffffffc07a994a [qede]
#9 [ffffb9e4f2907cd8] __rh_call_get_link_ksettings at ffffffff992b01a3
#10 [ffffb9e4f2907d38] __ethtool_get_link_ksettings at ffffffff992b04e4
#11 [ffffb9e4f2907d90] duplex_show at ffffffff99260300
#12 [ffffb9e4f2907e38] dev_attr_show at ffffffff9905a01c
#13 [ffffb9e4f2907e50] sysfs_kf_seq_show at ffffffff98e0145b
#14 [ffffb9e4f2907e68] seq_read at ffffffff98d902e3
#15 [ffffb9e4f2907ec8] vfs_read at ffffffff98d657d1
#16 [ffffb9e4f2907f00] ksys_read at ffffffff98d65c3f
#17 [ffffb9e4f2907f38] do_syscall_64 at ffffffff98a052fb
crash> struct net_device.state ffff9a9d21336000
state = 5,
state 5 is __LINK_STATE_START (0b1) and __LINK_STATE_NOCARRIER (0b100).
The device is not present, note lack of __LINK_STATE_PRESENT (0b10).
This is the same sort of panic as observed in commit 4224cfd7fb
("net-sysfs: add check for netdevice being present to speed_show").
There are many other callers of __ethtool_get_link_ksettings() which
don't have a device presence check.
Move this check into ethtool to protect all callers.
Fixes: d519e17e2d ("net: export device speed and duplex via sysfs")
Fixes: 4224cfd7fb ("net-sysfs: add check for netdevice being present to speed_show")
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Link: https://patch.msgid.link/8bae218864beaa44ed01628140475b9bf641c5b0.1724393671.git.jamie.bainbridge@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enhance the ethtool cable test interface by introducing the ability to
specify the source of the diagnostic information for cable test results.
This is particularly useful for PHYs that offer multiple diagnostic
methods, such as Time Domain Reflectometry (TDR) and Active Link Cable
Diagnostic (ALCD).
Key changes:
- Added `ethnl_cable_test_result_with_src` and
`ethnl_cable_test_fault_length_with_src` functions to allow specifying
the information source when reporting cable test results.
- Updated existing `ethnl_cable_test_result` and
`ethnl_cable_test_fault_length` functions to use TDR as the default
source, ensuring backward compatibility.
- Modified the UAPI to support these new attributes, enabling drivers to
provide more detailed diagnostic information.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240822120703.1393130-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ETH_SS_PHY_STATS command gets PHY statistics. Use the phydev pointer
from the ethnl request to allow query phy stats from each PHY on the
link.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cable testing is a PHY-specific command. Instead of targeting the command
towards dev->phydev, use the request to pick the targeted PHY.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
PSE and PD configuration is a PHY-specific command. Instead of targeting
the command towards dev->phydev, use the request to pick the targeted
PHY device.
As we don't get the PHY directly from the netdev's attached phydev, also
adjust the error messages.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLCA is a PHY-specific command. Instead of targeting the command
towards dev->phydev, use the request to pick the targeted PHY.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we have the ability to track the PHYs connected to a net_device
through the link_topology, we can expose this list to userspace. This
allows userspace to use these identifiers for phy-specific commands and
take the decision of which PHY to target by knowing the link topology.
Add PHY_GET and PHY_DUMP, which can be a filtered DUMP operation to list
devices on only one interface.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some netlink commands are target towards ethernet PHYs, to control some
of their features. As there's several such commands, add the ability to
pass a PHY index in the ethnl request, which will populate the generic
ethnl_req_info with the passed phy_index.
Add a helper that netlink command handlers need to use to grab the
targeted PHY from the req_info. This helper needs to hold rtnl_lock()
while interacting with the PHY, as it may be removed at any point.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
CMIS 5.2 standard section 9.4.2 defines four types of firmware update
supported mechanism: None, only LPL, only EPL, both LPL and EPL.
Currently, only LPL (Local Payload) type of write firmware block is
supported. However, if the module supports both LPL and EPL the flashing
process wrongly fails for no supporting LPL.
Fix that, by allowing the write mechanism to be LPL or both LPL and
EPL.
Fixes: c4f78134d4 ("ethtool: cmis_fw_update: add a layer for supporting firmware update using CDB")
Reported-by: Vladyslav Mykhaliuk <vmykhaliuk@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20240812140824.3718826-1-danieller@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Applications may want to deal with dynamic RSS contexts only.
So dumping context 0 will be counter-productive for them.
Support starting the dump from a given context ID.
Alternative would be to implement a dump flag to skip just
context 0, not sure which is better...
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we track RSS contexts in the core we can easily dump
them. This is a major introspection improvement, as previously
the only way to find all contexts would be to try all ids
(of which there may be 2^32 - 1).
Don't use the XArray iterators (like xa_for_each_start()) as they
do not move the index past the end of the array once done, which
caused multiple bugs in Netlink dumps in the past.
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOCTL already uses the XArray when reporting info about additional
contexts. Do the same thing in netlink code.
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor calling device ops out of rss_prepare_data().
Next patch will add alternative path using xarray.
No functional changes.
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
marvell/otx2 and mvpp2 do not support setting different
keys for different RSS contexts. Contexts have separate
indirection tables but key is shared with all other contexts.
This is likely fine, indirection table is the most important
piece.
Don't report the key-related parameters from such drivers.
This prevents driver-errors, e.g. otx2 always writes
the main key, even when user asks to change per-context key.
The second reason is that without this change tracking
the keys by the core gets complicated. Even if the driver
correctly reject setting key with rss_context != 0,
change of the main key would have to be reflected in
the XArray for all additional contexts.
Since the additional contexts don't have their own keys
not including the attributes (in Netlink speak) seems
intuitive. ethtool CLI seems to deal with it just fine.
Having to set the flag in majority of the drivers is
a bit tedious but not reporting the key is a safer
default.
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
cap_rss_ctx_supported was created because the API for creating
and configuring additional contexts is mux'ed with the normal
RSS API. Presence of ops does not imply driver can actually
support rss_context != 0 (in fact drivers mostly ignore that
field). cap_rss_ctx_supported lets core check that the driver
is context-aware before calling it.
Now that we have .create_rxfh_context, there is no such
ambiguity. We can depend on presence of the op.
Make setting the bit optional.
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ethtool_set_channel calls separate functions to check whether
the new channel number violates rss configuration or flow steering
configuration.
Very soon we need to check whether the new channel number violates
memory provider configuration as well.
To do all 3 checks cleanly, add a wrapper around
ethtool_get_max_rxnfc_channel() and ethtool_get_max_rxfh_channel(),
which does both checks. We can later extend this wrapper to add the
memory provider check in one place.
Note that in the current code, we put a descriptive genl error message
when we run into issues. To preserve the error message, we pass the
genl_info* to the common helper. The ioctl calls can pass NULL instead.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20240808205345.2141858-1-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A value of 1 doesn't make sense, as it implies the only allowed
context ID is 0, which is reserved for the default context - in
which case the driver should just not claim to support custom
RSS contexts at all.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/c07725b3a3d0b0a63b85e230f9c77af59d4d07f8.1723045898.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'at least one change' requirement is not applicable for context
creation, skip the check in such case.
This allows a command such as 'ethtool -X eth0 context new' to work.
The command works by mistake when using older versions of userspace
ethtool due to an incompatibility issue where rxfh.input_xfrm is passed
as zero (unset) instead of RXH_XFRM_NO_CHANGE as done with recent
userspace. This patch does not try to solve the incompatibility issue.
Link: https://lore.kernel.org/netdev/05ae8316-d3aa-4356-98c6-55ed4253c8a7@nvidia.com/
Fixes: 84a1d9c482 ("net: ethtool: extend RXNFC API to support RSS spreading of filter matches")
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20240807173352.3501746-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both ethtool_ops.rxfh_max_context_id and the default value used when
it's not specified are supposed to be exclusive maxima (the former
is documented as such; the latter, U32_MAX, cannot be used as an ID
since it equals ETH_RXFH_CONTEXT_ALLOC), but xa_alloc() expects an
inclusive maximum.
Subtract one from 'limit' to produce an inclusive maximum, and pass
that to xa_alloc().
Increase bnxt's max by one to prevent a (very minor) regression, as
BNXT_MAX_ETH_RSS_CTX is an inclusive max. This is safe since bnxt
is not actually hard-limited; BNXT_MAX_ETH_RSS_CTX is just a
leftover from old driver code that managed context IDs itself.
Rename rxfh_max_context_id to rxfh_max_num_contexts to make its
semantics (hopefully) more obvious.
Fixes: 847a8ab186 ("net: ethtool: let the core choose RSS context IDs")
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/5a2d11a599aa5b0cc6141072c01accfb7758650c.1723045898.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ethtool_cmis_page_fini() is declared but never implemented.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Link: https://patch.msgid.link/20240803112213.4044015-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We expect drivers implementing the new create/modify/destroy
API to populate the defaults in struct ethtool_rxfh_context.
In legacy API ctx isn't even passed, and rxfh.indir / rxfh.key
are NULL so drivers can't give us defaults even if they want to.
Call get_rxfh() to fetch the values. We can reuse rxfh_dev
for the get_rxfh(), rxfh stores the input from the user.
This fixes IOCTL reporting 0s instead of the default key /
indir table for drivers using legacy API.
Add a check to try to catch drivers using the new API
but not populating the key.
Fixes: 7964e78846 ("net: ethtool: use the tracking array for get_rxfh on custom RSS contexts")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The indirection table and the key follow struct ethtool_rxfh
in user memory.
To reset the indirection table user space calls SET_RXFH with
table of size 0 (OTOH to say "no change" it should use -1 / ~0).
The logic for calculating the offset where they key sits is
incorrect in this case, as kernel would still offset by the full
table length, while for the reset there is no indir table and
key is immediately after the struct.
$ ethtool -X eth0 default hkey 01:02:03...
$ ethtool -x eth0
[...]
RSS hash key:
00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00
[...]
Fixes: 3de0b59239 ("ethtool: Support for configurable RSS hash key")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The response to a GET request in Netlink should fully identify
the queried object. RSS_GET accepts context id as an input,
so it must echo that attribute back to the response.
After (assuming context 1 has been created):
$ ./cli.py --spec netlink/specs/ethtool.yaml \
--do rss-get \
--json '{"header": {"dev-index": 2}, "context": 1}'
{'context': 1,
'header': {'dev-index': 2, 'dev-name': 'eth0'},
[...]
Fixes: 7112a04664 ("ethtool: add netlink based get rss support")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20240724234249.2621109-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge in late fixes to prepare for the 6.11 net-next PR.
Conflicts:
93c3a96c30 ("net: pse-pd: Do not return EOPNOSUPP if config is null")
4cddb0f15e ("net: ethtool: pse-pd: Fix possible null-deref")
30d7b67277 ("net: ethtool: Add new power limit get and set features")
https://lore.kernel.org/20240715123204.623520bb@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In prevision to add new UAPI for hwtstamp we will be limited to the struct
ethtool_ts_info that is currently passed in fixed binary format through the
ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code
already started operating on an extensible kernel variant of that
structure, similar in concept to struct kernel_hwtstamp_config vs struct
hwtstamp_config.
Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here
we introduce the kernel-only structure in include/linux/ethtool.h.
The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO.
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change the API to select MAC default time stamping instead of the PHY.
Indeed the PHY is closer to the wire therefore theoretically it has less
delay than the MAC timestamping but the reality is different. Due to lower
time stamping clock frequency, latency in the MDIO bus and no PHC hardware
synchronization between different PHY, the PHY PTP is often less precise
than the MAC. The exception is for PHY designed specially for PTP case but
these devices are not very widespread. For not breaking the compatibility
default_timestamp flag has been introduced in phy_device that is set by
the phy driver to know we are using the old API behavior.
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-4-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce a new link mode necessary for 10 MBit single-pair
connection in BroadR-Reach mode on bcm5481x PHY by Broadcom.
This new link mode, 10baseT1BRR, is known as 1BR10 in the Broadcom
terminology. Another link mode to be used is 1BR100 and it is already
present as 100baseT1, because Broadcom's 1BR100 became 100baseT1
(IEEE 802.3bw).
Signed-off-by: Kamil Horák (2N) <kamilh@axis.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240712150709.3134474-2-kamilh@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For a PSE supporting both c33 and PoDL, setting config for one type of PoE
leaves the other type's config null. Currently, this case returns
EOPNOTSUPP, which is incorrect. Instead, we should do nothing if the
configuration is empty.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Fixes: d83e13761d ("net: pse-pd: Use regulator framework within PSE framework")
Link: https://patch.msgid.link/20240711-fix_pse_pd_deref-v3-1-edd78fc4fe42@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
