This is the third commit of the implementation of the CFM protocol
according to 802.1Q section 12.14.
Functionality is extended with CCM frame reception.
The MEP instance now contains CCM based status information.
Most important is the CCM defect status indicating if correct
CCM frames are received with the expected interval.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the second commit of the implementation of the CFM protocol
according to 802.1Q section 12.14.
Functionality is extended with CCM frame transmission.
Interface is extended with these functions:
br_cfm_cc_rdi_set()
br_cfm_cc_ccm_tx()
br_cfm_cc_config_set()
A MEP Continuity Check feature can be configured by
br_cfm_cc_config_set()
The Continuity Check parameters can be configured to be used when
transmitting CCM.
A MEP can be configured to start or stop transmission of CCM frames by
br_cfm_cc_ccm_tx()
The CCM will be transmitted for a selected period in seconds.
Must call this function before timeout to keep transmission alive.
A MEP transmitting CCM can be configured with inserted RDI in PDU by
br_cfm_cc_rdi_set()
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the first commit of the implementation of the CFM protocol
according to 802.1Q section 12.14.
It contains MEP instance create, delete and configuration.
Connectivity Fault Management (CFM) comprises capabilities for
detecting, verifying, and isolating connectivity failures in
Virtual Bridged Networks. These capabilities can be used in
networks operated by multiple independent organizations, each
with restricted management access to each others equipment.
CFM functions are partitioned as follows:
- Path discovery
- Fault detection
- Fault verification and isolation
- Fault notification
- Fault recovery
Interface consists of these functions:
br_cfm_mep_create()
br_cfm_mep_delete()
br_cfm_mep_config_set()
br_cfm_cc_config_set()
br_cfm_cc_peer_mep_add()
br_cfm_cc_peer_mep_remove()
A MEP instance is created by br_cfm_mep_create()
-It is the Maintenance association End Point
described in 802.1Q section 19.2.
-It is created on a specific level (1-7) and is assuring
that no CFM frames are passing through this MEP on lower levels.
-It initiates and validates CFM frames on its level.
-It can only exist on a port that is related to a bridge.
-Attributes given cannot be changed until the instance is
deleted.
A MEP instance can be deleted by br_cfm_mep_delete().
A created MEP instance has attributes that can be
configured by br_cfm_mep_config_set().
A MEP Continuity Check feature can be configured by
br_cfm_cc_config_set()
The Continuity Check Receiver state machine can be
enabled and disabled.
According to 802.1Q section 19.2.8
A MEP can have Peer MEPs added and removed by
br_cfm_cc_peer_mep_add() and br_cfm_cc_peer_mep_remove()
The Continuity Check feature can maintain connectivity
status on each added Peer MEP.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This makes it possible to include or exclude the CFM
protocol according to 802.1Q section 12.14.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch extends the processing of frames in the bridge. Currently MRP
frames needs special processing and the current implementation doesn't
allow a nice way to process different frame types. Therefore try to
improve this by adding a list that contains frame types that need
special processing. This list is iterated for each input frame and if
there is a match based on frame type then these functions will be called
and decide what to do with the frame. It can process the frame then the
bridge doesn't need to do anything or don't process so then the bridge
will do normal forwarding.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes an error causing small packets to get dropped. skb_ensure_writable
expects the second parameter to be a length in the ethernet payload.=20
If we want to write the ethernet header (src, dst), we should pass 0.
Otherwise, packets with small payloads (< ETH_ALEN) will get dropped.
Fixes: c1a8311679 ("netfilter: bridge: convert skb_make_writable to skb_ensure_writable")
Signed-off-by: Timothée COCAULT <timothee.cocault@orange.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit is correcting NETLINK br_fill_ifinfo() to be able to
handle 'filter_mask' with multiple flags asserted.
Fixes: 36a8e8e265 ("bridge: Extend br_fill_ifinfo to return MPR status")
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Suggested-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions related to nested interface infrastructure such as
netdev_walk_all_{ upper | lower }_dev() pass both private functions
and "data" pointer to handle their own things.
At this point, the data pointer type is void *.
In order to make it easier to expand common variables and functions,
this new netdev_nested_priv structure is added.
In the following patch, a new member variable will be added into this
struct to fix the lockdep issue.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a user-space software manages fdb entries externally it should
set the ext_learn flag which marks the fdb entry as externally managed
and avoids expiring it (they're treated as static fdbs). Unfortunately
on events where fdb entries are flushed (STP down, netlink fdb flush
etc) these fdbs are also deleted automatically by the bridge. That in turn
causes trouble for the managing user-space software (e.g. in MLAG setups
we lose remote fdb entries on port flaps).
These entries are completely externally managed so we should avoid
automatically deleting them, the only exception are offloaded entries
(i.e. BR_FDB_ADDED_BY_EXT_LEARN + BR_FDB_OFFLOADED). They are flushed as
before.
Fixes: eb100e0e24 ("net: bridge: allow to add externally learned entries from user-space")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should remove a group from the sg_port hash only if it's an S,G
entry. This makes it correct and more symmetric with group add. Also
since *,G groups are not added to that hash we can hide a bug.
Fixes: 085b53c8be ("net: bridge: mcast: add sg_port rhashtable")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to avoid forwarding to ports in MCAST_INCLUDE filter mode when the
mdst entry is a *,G or when the port has the blocked flag.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since host joins are considered as EXCLUDE {} joins we need to reflect
that in all of *,G ports' S,G entries. Since the S,Gs can have
host_joined == true only set automatically we can safely set it to false
when removing all automatically added entries upon S,G delete.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When excluding S,G entries we need a way to block a particular S,G,port.
The new port group flag is managed based on the source's timer as per
RFCs 3376 and 3810. When a source expires and its port group is in
EXCLUDE mode, it will be blocked.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to handle group filter mode transitions and initial state.
To change a port group's INCLUDE -> EXCLUDE mode (or when we have added
a new port group in EXCLUDE mode) we need to add that port to all of
*,G ports' S,G entries for proper replication. When the EXCLUDE state is
changed from IGMPv3 report, br_multicast_fwd_filter_exclude() must be
called after the source list processing because the assumption is that
all of the group's S,G entries will be created before transitioning to
EXCLUDE mode, i.e. most importantly its blocked entries will already be
added so it will not get automatically added to them.
The transition EXCLUDE -> INCLUDE happens only when a port group timer
expires, it requires us to remove that port from all of *,G ports' S,G
entries where it was automatically added previously.
Finally when we are adding a new S,G entry we must add all of *,G's
EXCLUDE ports to it.
In order to distinguish automatically added *,G EXCLUDE ports we have a
new port group flag - MDB_PG_FLAGS_STAR_EXCL.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for automatic install of S,G mdb entries based
on the port group's source list and the source entry's timer.
Once installed the S,G will be used when forwarding packets if the
approprate multicast/mld versions are set. A new source flag called
BR_SGRP_F_INSTALLED denotes if the source has a forwarding mdb entry
installed.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To speedup S,G forward handling we need to be able to quickly find out
if a port is a member of an S,G group. To do that add a global S,G port
rhashtable with key: source addr, group addr, protocol, vid (all br_ip
fields) and port pointer.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be able to differentiate between pg entries created by
user-space and the kernel when we start generating S,G entries for
IGMPv3/MLDv2's fast path. User-space entries are created by default as
RTPROT_STATIC and the kernel entries are RTPROT_KERNEL. Later we can
allow user-space to provide the entry rt_protocol so we can
differentiate between who added the entries specifically (e.g. clag,
admin, frr etc).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If (S,G) entries are enabled (igmpv3/mldv2) then look them up first. If
there isn't a present (S,G) entry then try to find (*,G).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new mdb attributes (MDBE_ATTR_SOURCE for setting,
MDBA_MDB_EATTR_SOURCE for dumping) to allow add/del and dump of mdb
entries with a source address (S,G). New S,G entries are created with
filter mode of MCAST_INCLUDE. The same attributes are used for IPv4 and
IPv6, they're validated and parsed based on their protocol.
S,G host joined entries which are added by user are not allowed yet.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the MDB add/del code expects an exact struct br_mdb_entry we can't
really add any extensions, thus add a new nested attribute at the level of
MDBA_SET_ENTRY called MDBA_SET_ENTRY_ATTRS which will be used to pass
all new options via netlink attributes. This patch doesn't change
anything functionally since the new attribute is not used yet, only
parsed.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now we have src in br_ip, u no longer makes sense so rename
it to dst. No functional changes.
v2: fix build with CONFIG_BATMAN_ADV_MCAST
CC: Marek Lindner <mareklindner@neomailbox.ch>
CC: Simon Wunderlich <sw@simonwunderlich.de>
CC: Antonio Quartulli <a@unstable.cc>
CC: Sven Eckelmann <sven@narfation.org>
CC: b.a.t.m.a.n@lists.open-mesh.org
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have src and dst in br_ip it is logical to use the src field
for the cases where we need to work with a source address such as
querier source address and group source address.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass and use extack all the way down to br_mdb_add_group().
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid doing duplicate device checks and searches (the same were done
in br_mdb_add and __br_mdb_add) pass the already found port to __br_mdb_add
and pull the bridge's netif_running and enabled multicast checks to
br_mdb_add. This would also simplify the future extack errors.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can drop the pr_info() calls and just use extack to return a
meaningful error to user-space when br_mdb_parse() fails.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling the RCU brother of br_vlan_get_pvid(), lockdep warns:
=============================
WARNING: suspicious RCU usage
5.9.0-rc3-01631-g13c17acb8e38-dirty #814 Not tainted
-----------------------------
net/bridge/br_private.h:1054 suspicious rcu_dereference_protected() usage!
Call trace:
lockdep_rcu_suspicious+0xd4/0xf8
__br_vlan_get_pvid+0xc0/0x100
br_vlan_get_pvid_rcu+0x78/0x108
The warning is because br_vlan_get_pvid_rcu() calls nbp_vlan_group()
which calls rtnl_dereference() instead of rcu_dereference(). In turn,
rtnl_dereference() calls rcu_dereference_protected() which assumes
operation under an RCU write-side critical section, which obviously is
not the case here. So, when the incorrect primitive is used to access
the RCU-protected VLAN group pointer, READ_ONCE() is not used, which may
cause various unexpected problems.
I'm sad to say that br_vlan_get_pvid() and br_vlan_get_pvid_rcu() cannot
share the same implementation. So fix the bug by splitting the 2
functions, and making br_vlan_get_pvid_rcu() retrieve the VLAN groups
under proper locking annotations.
Fixes: 7582f5b70f ("bridge: add br_vlan_get_pvid_rcu()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop repeated words in net/bridge/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When we're handling TO_EXCLUDE report in EXCLUDE filter mode we should
not ignore the return value of __grp_src_toex_excl() as we'll miss
sending notifications about group changes.
Fixes: 5bf1e00b68 ("net: bridge: mcast: support for IGMPV3/MLDv2 CHANGE_TO_INCLUDE/EXCLUDE report")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so the switchdev can notifiy the bridge to flush non-permanent fdb entries
for this port. This is useful whenever the hardware fdb of the switchdev
is reset, but the netdev and the bridgeport are not deleted.
Note that this has the same effect as the IFLA_BRPORT_FLUSH attribute.
CC: Jiri Pirko <jiri@resnulli.us>
CC: Ivan Vecera <ivecera@redhat.com>
CC: Roopa Prabhu <roopa@nvidia.com>
CC: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each MDB entry is encoded in a nested netlink attribute called
'MDBA_MDB_ENTRY'. In turn, this attribute contains another nested
attributed called 'MDBA_MDB_ENTRY_INFO', which encodes a single port
group entry within the MDB entry.
The cited commit added the ability to restart a dump from a specific
port group entry. However, on failure to add a port group entry to the
dump the entire MDB entry (stored in 'nest2') is removed, resulting in
missing port group entries.
Fix this by finalizing the MDB entry with the partial list of already
encoded port group entries.
Fixes: 5205e919c9 ("net: bridge: mcast: add support for src list and filter mode dumping")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Rewrite inner header IPv6 in ICMPv6 messages in ip6t_NPT,
from Michael Zhou.
2) do_ip_vs_set_ctl() dereferences uninitialized value,
from Peilin Ye.
3) Support for userdata in tables, from Jose M. Guisado.
4) Do not increment ct error and invalid stats at the same time,
from Florian Westphal.
5) Remove ct ignore stats, also from Florian.
6) Add ct stats for clash resolution, from Florian Westphal.
7) Bump reference counter bump on ct clash resolution only,
this is safe because bucket lock is held, again from Florian.
8) Use ip_is_fragment() in xt_HMARK, from YueHaibing.
9) Add wildcard support for nft_socket, from Balazs Scheidler.
10) Remove superfluous IPVS dependency on iptables, from
Yaroslav Bolyukin.
11) Remove unused definition in ebt_stp, from Wang Hai.
12) Replace CONFIG_NFT_CHAIN_NAT_{IPV4,IPV6} by CONFIG_NFT_NAT
in selftests/net, from Fabian Frederick.
13) Add userdata support for nft_object, from Jose M. Guisado.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen reported the following warning:
net/bridge/br_multicast.c: In function 'br_multicast_find_port':
net/bridge/br_multicast.c:1818:21: warning: unused variable 'br' [-Wunused-variable]
1818 | struct net_bridge *br = mp->br;
| ^~
It happens due to bridge's mlock_dereference() when lockdep isn't defined.
Silence the warning by annotating the variable as __maybe_unused.
Fixes: 0436862e41 ("net: bridge: mcast: support for IGMPv3/MLDv2 ALLOW_NEW_SOURCES report")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPDU_TYPE_TCN is never used after it was introduced.
So better to remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since each entry type has timers that can be running simultaneously we need
to make sure that entries are not freed before their timers have finished.
In order to do that generalize the src gc work to mcast gc work and use a
callback to free the entries (mdb, port group or src).
v3: add IPv6 support
v2: force mcast gc on port del to make sure all port group timers have
finished before freeing the bridge port
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When an IGMPv3/MLDv2 query is received and we're operating in such mode
then we need to avoid updating group timers if the suppress flag is set.
Also we should update only timers for groups in exclude mode.
v3: add IPv6/MLDv2 support
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We already have all necessary helpers, so process IGMPV3/MLDv2
BLOCK_OLD_SOURCES as per the RFCs.
v3: add IPv6/MLDv2 support
v2: directly do flag bit operations
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to process IGMPV3/MLDv2 CHANGE_TO_INCLUDE/EXCLUDE report types we
need new helpers which allow us to mark entries based on their timer
state and to query only marked entries.
v3: add IPv6/MLDv2 support, fix other_query checks
v2: directly do flag bit operations
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to process IGMPV3/MLDv2_MODE_IS_INCLUDE/EXCLUDE report types we
need some new helpers which allow us to set/clear flags for all current
entries and later delete marked entries after the report sources have been
processed.
v3: add IPv6/MLDv2 support
v2: drop flag helpers and directly do flag bit operations
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds handling for the ALLOW_NEW_SOURCES IGMPv3/MLDv2 report
types and limits them only when multicast_igmp_version == 3 or
multicast_mld_version == 2 respectively. Now that IGMPv3/MLDv2 handling
functions will be managing timers we need to delay their activation, thus
a new argument is added which controls if the timer should be updated.
We also disable host IGMPv3/MLDv2 handling as it's not yet implemented and
could cause inconsistent group state, the host can only join a group as
EXCLUDE {} or leave it.
v4: rename update_timer to igmpv2_mldv1 and use the passed value from
br_multicast_add_group's callers
v3: Add IPv6/MLDv2 support
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If an expired port group is in EXCLUDE mode, then we have to turn it
into INCLUDE mode, remove all srcs with zero timer and finally remove
the group itself if there are no more srcs with an active timer.
For IGMPv2 use there would be no sources, so this will reduce to just
removing the group as before.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have to use mdb and port entries when sending mdb notifications in
order to fill in all group attributes properly. Before this change we
would've used a fake br_mdb_entry struct to fill in only partial
information about the mdb. Now we can also reuse the mdb dump fill
function and thus have only a single central place which fills the mdb
attributes.
v3: add IPv6 support
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change is in preparation for using the mdb port group entries when
sending a notification, so their full state and additional attributes can
be filled in.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need to be able to retransmit group-specific and group-and-source
specific queries. The new timer takes care of those.
v3: add IPv6 support
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allows br_multicast_alloc_query to build queries with the port group's
source lists and sends a query for sources over and under lmqt when
necessary as per RFCs 3376 and 3810 with the suppress flag set
appropriately.
v3: add IPv6 support
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support per port group src list (address and timer) and filter mode
dumping. Protected by either multicast_lock or rcu.
v3: add IPv6 support
v2: require RCU or multicast_lock to traverse src groups
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Initial functions for group source lists which are needed for IGMPv3
and MLDv2 include/exclude lists. Both IPv4 and IPv6 sources are supported.
User-added mdb entries are created with exclude filter mode, we can
extend that later to allow user-supplied mode. When group src entries
are deleted, they're freed from a workqueue to make sure their timers
are not still running. Source entries are protected by the multicast_lock
and rcu. The number of src groups per port group is limited to 32.
v4: use the new port group del function directly
add igmpv2/mldv1 bool to denote if the entry was added in those
modes, it will later replace the old update_timer bool
v3: add IPv6 support
v2: allow src groups to be traversed under rcu
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to avoid future errors and reduce code duplication we should
factor out the port group del sequence. This allows us to have one
function which takes care of all details when removing a port group.
v4: set pg's fast leave flag when deleting due to fast leave
move the patch before adding source lists
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before this patch we'd need 2 cache lines for fast-path, now all used
fields are in the first cache line.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change places that open-code NLA_POLICY_EXACT_LEN() to
use the macro instead, giving us flexibility in how we
handle the details of the macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzkaller reports splat:
------------[ cut here ]------------
Buffer overflow detected (80 < 137)!
Call Trace:
do_ebt_get_ctl+0x2b4/0x790 net/bridge/netfilter/ebtables.c:2317
nf_getsockopt+0x72/0xd0 net/netfilter/nf_sockopt.c:116
ip_getsockopt net/ipv4/ip_sockglue.c:1778 [inline]
caused by a copy-to-user with a too-large "*len" value.
This adds a argument check on *len just like in the non-compat version
of the handler.
Before the "Fixes" commit, the reproducer fails with -EINVAL as
expected:
1. core calls the "compat" getsockopt version
2. compat getsockopt version detects the *len value is possibly
in 64-bit layout (*len != compat_len)
3. compat getsockopt version delegates everything to native getsockopt
version
4. native getsockopt rejects invalid *len
-> compat handler only sees len == sizeof(compat_struct) for GET_ENTRIES.
After the refactor, event sequence is:
1. getsockopt calls "compat" version (len != native_len)
2. compat version attempts to copy *len bytes, where *len is random
value from userspace
Fixes: fc66de8e16 ("netfilter/ebtables: clean up compat {get, set}sockopt handling")
Reported-by: syzbot+5accb5c62faa1d346480@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_ct_frag6_gather is part of nf_defrag_ipv6.ko, not ipv6 core.
The current use of the netfilter ipv6 stub indirections causes a module
dependency between ipv6 and nf_defrag_ipv6.
This prevents nf_defrag_ipv6 module from being removed because ipv6 can't
be unloaded.
Remove the indirection and always use a direct call. This creates a
depency from nf_conntrack_bridge to nf_defrag_ipv6 instead:
modinfo nf_conntrack
depends: nf_conntrack,nf_defrag_ipv6,bridge
.. and nf_conntrack already depends on nf_defrag_ipv6 anyway.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
-----BEGIN PGP SIGNATURE-----
iQJIBAABCAAyFiEES0KozwfymdVUl37v6iDy2pc3iXMFAl8okpIUHHBhdWxAcGF1
bC1tb29yZS5jb20ACgkQ6iDy2pc3iXNqOQ/8D+m9Ykcby3csEKsp8YtsaukEu62U
lRVaxzRNO9wwB24aFwDFuJnIkmsSi/s/O4nBsy2mw+Apn+uDCvHQ9tBU07vlNn2f
lu27YaTya7YGlqoe315xijd8tyoX99k8cpQeixvAVr9/jdR09yka7SJ8O7X9mjV7
+SUVDiKCplPKpiwCCRS9cqD7F64T6y35XKzbrzYqdP0UOF2XelZo/Evt5rDRvWUf
5qDN2tP+iM/Fvu5lCfczFwAeivfAdxjQ11n783hx8Ms2qyiaKQCzbEwjqAslmkbs
1k/+ED0NjzXX1ne0JZaz/bk0wsMnmOoa8o+NDcyd7Za/cj5prUZi7kBy+xry4YV8
qKJ40Lk0flCWgUpm6bkYVOByIYHk0gmfBNvjilqf25NR/eOC/9e9ir8PywvYUW/7
kvVK37+N/a3LnFj80sZpIeqqnNU8z9PV1i7//5/kDuKvz94Bq83TJDO6pPKvqDtC
njQfCFoHwdEeF8OalK793lIiYaoODqvbkWKChKMqziODJ4ZP8AW06gXpEbEWn7G3
TTnJx7hqzR9t90vBQJeO3Fromfn+9TDlZVdX+EGO8gIqUiLGr0r7LPPep4VkDbNw
LxMYKeC2cgRp8Z+XXPDxfXSDL2psTwg6CXcDrXcYnUyBo/yerpBvbJkeaR0h+UR0
j6cvMX+T39X2JXM=
=Xs3M
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20200803' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"Aside from some smaller bug fixes, here are the highlights:
- add a new backlog wait metric to the audit status message, this is
intended to help admins determine how long processes have been
waiting for the audit backlog queue to clear
- generate audit records for nftables configuration changes
- generate CWD audit records for for the relevant LSM audit records"
* tag 'audit-pr-20200803' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: report audit wait metric in audit status reply
audit: purge audit_log_string from the intra-kernel audit API
audit: issue CWD record to accompany LSM_AUDIT_DATA_* records
audit: use the proper gfp flags in the audit_log_nfcfg() calls
audit: remove unused !CONFIG_AUDITSYSCALL __audit_inode* stubs
audit: add gfp parameter to audit_log_nfcfg
audit: log nftables configuration change events
audit: Use struct_size() helper in alloc_chunk
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) UAF in chain binding support from previous batch, from Dan Carpenter.
2) Queue up delayed work to expire connections with no destination,
from Andrew Sy Kim.
3) Use fallthrough pseudo-keyword, from Gustavo A. R. Silva.
4) Replace HTTP links with HTTPS, from Alexander A. Klimov.
5) Remove superfluous null header checks in ip6tables, from
Gaurav Singh.
6) Add extended netlink error reporting for expression.
7) Report EEXIST on overlapping chain, set elements and flowtable
devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to clear all of the bridge private skb variables as they can be
stale due to the packet being recirculated through the stack and then
transmitted through the bridge device. Similar memset is already done on
bridge's input. We've seen cases where proxyarp_replied was 1 on routed
multicast packets transmitted through the bridge to ports with neigh
suppress which were getting dropped. Same thing can in theory happen with
the port isolation bit as well.
Fixes: 821f1b21ca ("bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the native and compat {get,set}sockopt handlers using
in_compat_syscall(). Note that this required moving a fair
amout of code around to be done sanely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new port attribute, IFLA_BRPORT_MRP_IN_OPEN, which
allows to notify the userspace when the node lost the contiuity of
MRP_InTest frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the function br_mrp_fill_info to return also the
status for the interconnect ring.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the existing MRP netlink interface with the following
attributes: IFLA_BRIDGE_MRP_IN_ROLE, IFLA_BRIDGE_MRP_IN_STATE and
IFLA_BRIDGE_MRP_START_IN_TEST. These attributes are similar with their
ring attributes but they apply to the interconnect port.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thie patch adds support for MRP Interconnect. Similar with the MRP ring,
if the HW can't generate MRP_InTest frames, then the SW will try to
generate them. And if also the SW fails to generate the frames then an
error is return to userspace.
The forwarding/termination of MRP_In frames is happening in the kernel
and is done by MRP instances.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the MRP API for interconnect switchdev. Similar with the other
br_mrp_switchdev function, these function will just eventually call the
switchdev functions: switchdev_port_obj_add/del.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function notifies the userspace when the node lost the continuity
of MRP_InTest frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the function br_mrp_port_open to
br_mrp_ring_port_open. In this way is more clear that a ring port lost
the continuity because there will be also a br_mrp_in_port_open.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the 'struct br_mrp' to contain information regarding
the MRP interconnect. It contains the following:
- the interconnect port 'i_port', which is NULL if the node doesn't have
a interconnect role
- the interconnect id, which is similar with the ring id, but this field
is also part of the MRP_InTest frames.
- the interconnect role, which can be MIM or MIC.
- the interconnect state, which can be open or closed.
- the interconnect delayed_work for sending MRP_InTest frames and check
for lost of continuity.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bridge vlan filtering is not defined we won't have
br_vlan_can_enter_range and thus will get a compile error as was
reported by Stephen and the build bot. So let's define a stub for when
vlan filtering is not used.
Fixes: 9433944368 ("net: bridge: notify on vlan tunnel changes done via the old api")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If someone uses the old vlan API to configure tunnel mappings we'll only
generate the old-style full port notification. That would be a problem
if we are monitoring the new vlan notifications for changes. The patch
resolves the issue by adding vlan notifications to the old tunnel netlink
code. As usual we try to compress the notifications for as many vlans
in a range as possible, thus a vlan tunnel change is considered able
to enter the "current" vlan notification range if:
1. vlan exists
2. it has actually changed (curr_change == true)
3. it passes all standard vlan notification range checks done by
br_vlan_can_enter_range() such as option equality, id continuity etc
Note that vlan tunnel changes (add/del) are considered a part of vlan
options so only RTM_NEWVLAN notification is generated with the relevant
information inside.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e57f61858b ("net: bridge: mcast: fix stale nsrcs pointer in
igmp3/mld2 report handling") introduced a bug in the IPv6 header payload
length check which would potentially lead to rejecting a valid MLD2 Report:
The check needs to take into account the 2 bytes for the "Number of
Sources" field in the "Multicast Address Record" before reading it.
And not the size of a pointer to this field.
Fixes: e57f61858b ("net: bridge: mcast: fix stale nsrcs pointer in igmp3/mld2 report handling")
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the function br_fill_ifinfo to return also the MRP
status for each instance on a bridge. It also adds a new filter
RTEXT_FILTER_MRP to return the MRP status only when this is set, not to
interfer with the vlans. The MRP status is return only on the bridge
interfaces.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the function br_mrp_fill_info which populates the MRP attributes
regarding the status of each MRP instance.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed an inconsistent use of GFP flags in nft_obj_notify() that used
GFP_KERNEL when a GFP flag was passed in to that function. Given this
allocated memory was then used in audit_log_nfcfg() it led to an audit
of all other GFP allocations in net/netfilter/nf_tables_api.c and a
modification of audit_log_nfcfg() to accept a GFP parameter.
Reported-by: Dan Carptenter <dan.carpenter@oracle.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net, they are:
1) Unaligned atomic access in ipset, from Russell King.
2) Missing module description, from Rob Gill.
3) Patches to fix a module unload causing NULL pointer dereference in
xtables, from David Wilder. For the record, I posting here his cover
letter explaining the problem:
A crash happened on ppc64le when running ltp network tests triggered by
"rmmod iptable_mangle".
See previous discussion in this thread:
https://lists.openwall.net/netdev/2020/06/03/161 .
In the crash I found in iptable_mangle_hook() that
state->net->ipv4.iptable_mangle=NULL causing a NULL pointer dereference.
net->ipv4.iptable_mangle is set to NULL in +iptable_mangle_net_exit() and
called when ip_mangle modules is unloaded. A rmmod task was found running
in the crash dump. A 2nd crash showed the same problem when running
"rmmod iptable_filter" (net->ipv4.iptable_filter=NULL).
To fix this I added .pre_exit hook in all iptable_foo.c. The pre_exit will
un-register the underlying hook and exit would do the table freeing. The
netns core does an unconditional +synchronize_rcu after the pre_exit hooks
insuring no packets are in flight that have picked up the pointer before
completing the un-register.
These patches include changes for both iptables and ip6tables.
We tested this fix with ltp running iptables01.sh and iptables01.sh -6 a
loop for 72 hours.
4) Add a selftest for conntrack helper assignment, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The eth_addr member is passed to ether_addr functions that require
2-byte alignment, therefore the member must be properly aligned
to avoid unaligned accesses.
The problem is in place since the initial merge of multicast to unicast:
commit 6db6f0eae6 bridge: multicast to unicast
Fixes: 6db6f0eae6 ("bridge: multicast to unicast")
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Thomas Martitz <t.martitz@avm.de>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user tool modinfo is used to get information on kernel modules, including a
description where it is available.
This patch adds a brief MODULE_DESCRIPTION to netfilter kernel modules
(descriptions taken from Kconfig file or code comments)
Signed-off-by: Rob Gill <rrobgill@protonmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When we modify or create a new fdb entry sometimes we want to avoid
refreshing its activity in order to track it properly. One example is
when a mac is received from EVPN multi-homing peer by FRR, which doesn't
want to change local activity accounting. It makes it static and sets a
flag to track its activity.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ability to notify about activity of any entries
(static, permanent or ext_learn). EVPN multihoming peers need it to
properly and efficiently handle mac sync (peer active/locally active).
We add a new NFEA_ACTIVITY_NOTIFY attribute which is used to dump the
current activity state and to control if static entries should be monitored
at all. We use 2 bits - one to activate fdb entry tracking (disabled by
default) and the second to denote that an entry is inactive. We need
the second bit in order to avoid multiple notifications of inactivity.
Obviously this makes no difference for dynamic entries since at the time
of inactivity they get deleted, while the tracked non-dynamic entries get
the inactive bit set and get a notification.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can just pass ndm as an argument instead of its fields separately.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds specific checks for primary(0x0) and secondary(0x1) when
setting the port role. For any other value the function
'br_mrp_set_port_role' will return -EINVAL.
Fixes: 20f6a05ef6 ("bridge: mrp: Rework the MRP netlink interface")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The dynamic key update for addr_list_lock still causes troubles,
for example the following race condition still exists:
CPU 0: CPU 1:
(RCU read lock) (RTNL lock)
dev_mc_seq_show() netdev_update_lockdep_key()
-> lockdep_unregister_key()
-> netif_addr_lock_bh()
because lockdep doesn't provide an API to update it atomically.
Therefore, we have to move it back to static keys and use subclass
for nest locking like before.
In commit 1a33e10e4a ("net: partially revert dynamic lockdep key
changes"), I already reverted most parts of commit ab92d68fc2
("net: core: add generic lockdep keys").
This patch reverts the rest and also part of commit f3b0a18bb6
("net: remove unnecessary variables and callback"). After this
patch, addr_list_lock changes back to using static keys and
subclasses to satisfy lockdep. Thanks to dev->lower_level, we do
not have to change back to ->ndo_get_lock_subclass().
And hopefully this reduces some syzbot lockdep noises too.
Reported-by: syzbot+f3a0e80c34b3fc28ac5e@syzkaller.appspotmail.com
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
-----BEGIN PGP SIGNATURE-----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=iLfC
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20200601' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"Summary of the significant patches:
- Record information about binds/unbinds to the audit multicast
socket. This helps identify which processes have/had access to the
information in the audit stream.
- Cleanup and add some additional information to the netfilter
configuration events collected by audit.
- Fix some of the audit error handling code so we don't leak network
namespace references"
* tag 'audit-pr-20200601' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: add subj creds to NETFILTER_CFG record to
audit: Replace zero-length array with flexible-array
audit: make symbol 'audit_nfcfgs' static
netfilter: add audit table unregister actions
audit: tidy and extend netfilter_cfg x_tables
audit: log audit netlink multicast bind and unbind
audit: fix a net reference leak in audit_list_rules_send()
audit: fix a net reference leak in audit_send_reply()
A node that has the MRA role, it can behave as MRM or MRC.
Initially it starts as MRM and sends MRP_Test frames on both ring ports.
If it detects that there are MRP_Test send by another MRM, then it
checks if these frames have a lower priority than itself. In this case
it would send MRP_Nack frames to notify the other node that it needs to
stop sending MRP_Test frames.
If it receives a MRP_Nack frame then it stops sending MRP_Test frames
and starts to behave as a MRC but it would continue to monitor the
MRP_Test frames send by MRM. If at a point the MRM stops to send
MRP_Test frames it would get the MRM role and start to send MRP_Test
frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each MRP instance has a priority, a lower value means a higher priority.
The priority of MRP instance is stored in MRP_Test frame in this way
all the MRP nodes in the ring can see other nodes priority.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When neighbor suppression is enabled the bridge device might reply to
Neighbor Solicitation (NS) messages on behalf of remote hosts.
In case the NS message includes the "Source link-layer address" option
[1], the bridge device will use the specified address as the link-layer
destination address in its reply.
To avoid an infinite loop, break out of the options parsing loop when
encountering an option with length zero and disregard the NS message.
This is consistent with the IPv6 ndisc code and RFC 4886 which states
that "Nodes MUST silently discard an ND packet that contains an option
with length zero" [2].
[1] https://tools.ietf.org/html/rfc4861#section-4.3
[2] https://tools.ietf.org/html/rfc4861#section-4.6
Fixes: ed842faeb2 ("bridge: suppress nd pkts on BR_NEIGH_SUPPRESS ports")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alla Segal <allas@mellanox.com>
Tested-by: Alla Segal <allas@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang-10 and clang-11 run into a corner case of the register
allocator on 32-bit ARM, leading to excessive stack usage from
register spilling:
net/bridge/br_multicast.c:2422:6: error: stack frame size of 1472 bytes in function 'br_multicast_get_stats' [-Werror,-Wframe-larger-than=]
Work around this by marking one of the internal functions as
noinline_for_stack.
Link: https://bugs.llvm.org/show_bug.cgi?id=45802#c9
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the MRP netlink interface. Before, each attribute
represented a binary structure which made it hard to be extended.
Therefore update the MRP netlink interface such that each existing
attribute to be a nested attribute which contains the fields of the
binary structures.
In this way the MRP netlink interface can be extended without breaking
the backwards compatibility. It is also using strict checking for
attributes under the MRP top attribute.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue was reported by syzbot. When the function br_mrp_parse was
called with a valid net_bridge_port, the net_bridge was an invalid
pointer. Therefore the check br->stp_enabled could pass/fail
depending where it was pointing in memory.
The fix consists of setting the net_bridge pointer if the port is a
valid pointer.
Reported-by: syzbot+9c6f0f1f8e32223df9a4@syzkaller.appspotmail.com
Fixes: 6536993371 ("bridge: mrp: Integrate MRP into the bridge")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, using the bridge reject target with tagged packets
results in untagged packets being sent back.
Fix this by mirroring the vlan id as well.
Fixes: 85f5b3086a ("netfilter: bridge: add reject support")
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When a MRP instance is deleted, then restore the port according to the
bridge state. If the bridge is up then the ports will be in forwarding
state otherwise will be in disabled state.
Fixes: 9a9f26e8f7 ("bridge: mrp: Connect MRP API with the switchdev API")
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allow to have the same net bridge port part of multiple MRP
rings. Therefore add a check if the port is used already in a different
MRP. In that case return failure.
Fixes: 9a9f26e8f7 ("bridge: mrp: Connect MRP API with the switchdev API")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8db0a2ee2c ("net: bridge: reject DSA-enabled master netdevices
as bridge members") added a special check in br_if.c in order to check
for a DSA master network device with a tagging protocol configured. This
was done because back then, such devices, once enslaved in a bridge
would become inoperative and would not pass DSA tagged traffic anymore
due to br_handle_frame returning RX_HANDLER_CONSUMED.
But right now we have valid use cases which do require bridging of DSA
masters. One such example is when the DSA master ports are DSA switch
ports themselves (in a disjoint tree setup). This should be completely
equivalent, functionally speaking, from having multiple DSA switches
hanging off of the ports of a switchdev driver. So we should allow the
enslaving of DSA tagged master network devices.
Instead of the regular br_handle_frame(), install a new function
br_handle_frame_dummy() on these DSA masters, which returns
RX_HANDLER_PASS in order to call into the DSA specific tagging protocol
handlers, and lift the restriction from br_add_if.
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netpoll_send_skb() callers seem to leak skb if
the np pointer is NULL. While this should not happen, we
can make the code more robust.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NL_SET_ERR_MSG_MOD macro is used to report a string describing an
error message to userspace via the netlink extended ACK structure. It
should not have a trailing newline.
Add a cocci script which catches cases where the newline marker is
present. Using this script, fix the handful of cases which accidentally
included a trailing new line.
I couldn't figure out a way to get a patch mode working, so this script
only implements context, report, and org.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
net/bridge/br_private.h:1334:8-9: WARNING: return of 0/1 in function
'br_mrp_enabled' with return type bool
Fixes: 6536993371 ("bridge: mrp: Integrate MRP into the bridge")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-05-01 (v2)
The following pull-request contains BPF updates for your *net-next* tree.
We've added 61 non-merge commits during the last 6 day(s) which contain
a total of 153 files changed, 6739 insertions(+), 3367 deletions(-).
The main changes are:
1) pulled work.sysctl from vfs tree with sysctl bpf changes.
2) bpf_link observability, from Andrii.
3) BTF-defined map in map, from Andrii.
4) asan fixes for selftests, from Andrii.
5) Allow bpf_map_lookup_elem for SOCKMAP and SOCKHASH, from Jakub.
6) production cloudflare classifier as a selftes, from Lorenz.
7) bpf_ktime_get_*_ns() helper improvements, from Maciej.
8) unprivileged bpftool feature probe, from Quentin.
9) BPF_ENABLE_STATS command, from Song.
10) enable bpf_[gs]etsockopt() helpers for sock_ops progs, from Stanislav.
11) enable a bunch of common helpers for cg-device, sysctl, sockopt progs,
from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
User space can request to delete a range of VLANs from a bridge slave in
one netlink request. For each deleted VLAN the FDB needs to be traversed
in order to flush all the affected entries.
If a large range of VLANs is deleted and the number of FDB entries is
large or the FDB lock is contented, it is possible for the kernel to
loop through the deleted VLANs for a long time. In case preemption is
disabled, this can result in a soft lockup.
Fix this by adding a schedule point after each VLAN is deleted to yield
the CPU, if needed. This is safe because the VLANs are traversed in
process context.
Fixes: bdced7ef78 ("bridge: support for multiple vlans and vlan ranges in setlink and dellink requests")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Tested-by: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Audit the action of unregistering ebtables and x_tables.
See: https://github.com/linux-audit/audit-kernel/issues/44
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
NETFILTER_CFG record generation was inconsistent for x_tables and
ebtables configuration changes. The call was needlessly messy and there
were supporting records missing at times while they were produced when
not requested. Simplify the logging call into a new audit_log_nfcfg
call. Honour the audit_enabled setting while more consistently
recording information including supporting records by tidying up dummy
checks.
Add an op= field that indicates the operation being performed (register
or replace).
Here is the enhanced sample record:
type=NETFILTER_CFG msg=audit(1580905834.919:82970): table=filter family=2 entries=83 op=replace
Generate audit NETFILTER_CFG records on ebtables table registration.
Previously this was being done for x_tables registration and replacement
operations and ebtables table replacement only.
See: https://github.com/linux-audit/audit-kernel/issues/25
See: https://github.com/linux-audit/audit-kernel/issues/35
See: https://github.com/linux-audit/audit-kernel/issues/43
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
It is not possible to have the MRP and STP running at the same time on the
bridge, therefore add check when enabling the STP to check if MRP is already
enabled. In that case return error.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To integrate MRP into the bridge, the bridge needs to do the following:
- detect if the MRP frame was received on MRP ring port in that case it would be
processed otherwise just forward it as usual.
- enable parsing of MRP
- before whenever the bridge was set up, it would set all the ports in
forwarding state. Add an extra check to not set ports in forwarding state if
the port is an MRP ring port. The reason of this change is that if the MRP
instance initially sets the port in blocked state by setting the bridge up it
would overwrite this setting.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement netlink interface to configure MRP. The implementation
will do sanity checks over the attributes and then eventually call the MRP
interface.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the MRP API.
In case the HW can't generate MRP Test frames then the SW will try to generate
the frames. In case that also the SW will fail in generating the frames then a
error is return to the userspace. The userspace is responsible to generate all
the other MRP frames regardless if the test frames are generated by HW or SW.
The forwarding/termination of MRP frames is happening in the kernel and is done
by the MRP instance. The userspace application doesn't do the forwarding.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the MRP api for switchdev.
These functions will just eventually call the switchdev functions:
switchdev_port_obj_add/del and switchdev_port_attr_set.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the MRP interface.
This interface is used by the netlink to update the MRP instances and by the MRP
to make the calls to switchdev to offload it to HW.
It defines an MRP instance 'struct br_mrp' which is a list of MRP instances.
Which will be part of the 'struct net_bridge'. Each instance has 2 ring ports,
a bridge and an ID.
In case the HW can't generate MRP Test frames then the SW will generate those.
br_mrp_add - adds a new MRP instance.
br_mrp_del - deletes an existing MRP instance. Each instance has an ID(ring_id).
br_mrp_set_port_state - changes the port state. The port can be in forwarding
state, which means that the frames can pass through or in blocked state which
means that the frames can't pass through except MRP frames. This will
eventually call the switchdev API to notify the HW. This information is used
also by the SW bridge to know how to forward frames in case the HW doesn't
have this capability.
br_mrp_set_port_role - a port role can be primary or secondary. This
information is required to be pushed to HW in case the HW can generate
MRP_Test frames. Because the MRP_Test frames contains a file with this
information. Otherwise the HW will not be able to generate the frames
correctly.
br_mrp_set_ring_state - a ring can be in state open or closed. State open means
that the mrp port stopped receiving MRP_Test frames, while closed means that
the mrp port received MRP_Test frames. Similar with br_mrp_port_role, this
information is pushed in HW because the MRP_Test frames contain this
information.
br_mrp_set_ring_role - a ring can have the following roles MRM or MRC. For the
role MRM it is expected that the HW can terminate the MRP frames, notify the
SW that it stopped receiving MRP_Test frames and trapp all the other MRP
frames. While for MRC mode it is expected that the HW can forward the MRP
frames only between the MRP ports and copy MRP_Topology frames to CPU. In
case the HW doesn't support a role it needs to return an error code different
than -EOPNOTSUPP.
br_mrp_start_test - this starts/stops the generation of MRP_Test frames. To stop
the generation of frames the interval needs to have a value of 0. In this case
the userspace needs to know if the HW supports this or not. Not to have
duplicate frames(generated by HW and SW). Because if the HW supports this then
the SW will not generate anymore frames and will expect that the HW will
notify when it stopped receiving MRP frames using the function
br_mrp_port_open.
br_mrp_port_open - this function is used by drivers to notify the userspace via
a netlink callback that one of the ports stopped receiving MRP_Test frames.
This function is called only when the node has the role MRM. It is not
supposed to be called from userspace.
br_mrp_port_switchdev_add - this corresponds to the function br_mrp_add,
and will notify the HW that a MRP instance is added. The function gets
as parameter the MRP instance.
br_mrp_port_switchdev_del - this corresponds to the function br_mrp_del,
and will notify the HW that a MRP instance is removed. The function
gets as parameter the ID of the MRP instance that is removed.
br_mrp_port_switchdev_set_state - this corresponds to the function
br_mrp_set_port_state. It would notify the HW if it should block or not
non-MRP frames.
br_mrp_port_switchdev_set_port - this corresponds to the function
br_mrp_set_port_role. It would set the port role, primary or secondary.
br_mrp_switchdev_set_role - this corresponds to the function
br_mrp_set_ring_role and would set one of the role MRM or MRC.
br_mrp_switchdev_set_ring_state - this corresponds to the function
br_mrp_set_ring_state and would set the ring to be open or closed.
br_mrp_switchdev_send_ring_test - this corresponds to the function
br_mrp_start_test. This will notify the HW to start or stop generating
MRP_Test frames. Value 0 for the interval parameter means to stop generating
the frames.
br_mrp_port_open - this function is used to notify the userspace that the port
lost the continuity of MRP Test frames.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new port attribute, IFLA_BRPORT_MRP_RING_OPEN, which allows
to notify the userspace when the port lost the continuite of MRP frames.
This attribute is set by kernel whenever the SW or HW detects that the ring is
being open or closed.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To integrate MRP into the bridge, first the bridge needs to be aware of ports
that are part of an MRP ring and which rings are on the bridge.
Therefore extend bridge interface with the following:
- add new flag(BR_MPP_AWARE) to the net bridge ports, this bit will be
set when the port is added to an MRP instance. In this way it knows if
the frame was received on MRP ring port
- add new flag(BR_MRP_LOST_CONT) to the net bridge ports, this bit will be set
when the port lost the continuity of MRP Test frames.
- add a list of MRP instances
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the option BRIDGE_MRP to allow to build in or not MRP support.
The default value is N.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having all the sysctl handlers deal with user pointers, which
is rather hairy in terms of the BPF interaction, copy the input to and
from userspace in common code. This also means that the strings are
always NUL-terminated by the common code, making the API a little bit
safer.
As most handler just pass through the data to one of the common handlers
a lot of the changes are mechnical.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that we have a nested tunnel info attribute we can add a separate
one for the tunnel command and require it explicitly from user-space. It
must be one of RTM_SETLINK/DELLINK. Only RTM_SETLINK requires a valid
tunnel id, DELLINK just removes it if it was set before. This allows us
to have all tunnel attributes and control in one place, thus removing
the need for an outside vlan info flag.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While discussing the new API, Roopa mentioned that we'll be adding more
tunnel attributes and options in the future, so it's better to make it a
nested attribute, since this is still in net-next we can easily change it
and nest the tunnel id attribute under BRIDGE_VLANDB_ENTRY_TUNNEL_INFO.
The new format is:
[BRIDGE_VLANDB_ENTRY]
[BRIDGE_VLANDB_ENTRY_TUNNEL_INFO]
[BRIDGE_VLANDB_TINFO_ID]
Any new tunnel attributes can be nested under
BRIDGE_VLANDB_ENTRY_TUNNEL_INFO.
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for vlan stats to be included when dumping vlan
information. We have to dump them only when explicitly requested (thus the
flag below) because that disables the vlan range compression and will make
the dump significantly larger. In order to request the stats to be
included we add a new dump attribute called BRIDGE_VLANDB_DUMP_FLAGS which
can affect dumps with the following first flag:
- BRIDGE_VLANDB_DUMPF_STATS
The stats are intentionally nested and put into separate attributes to make
it easier for extending later since we plan to add per-vlan mcast stats,
drop stats and possibly STP stats. This is the last missing piece from the
new vlan API which makes the dumped vlan information complete.
A dump request which should include stats looks like:
[BRIDGE_VLANDB_DUMP_FLAGS] |= BRIDGE_VLANDB_DUMPF_STATS
A vlandb entry attribute with stats looks like:
[BRIDGE_VLANDB_ENTRY] = {
[BRIDGE_VLANDB_ENTRY_STATS] = {
[BRIDGE_VLANDB_STATS_RX_BYTES]
[BRIDGE_VLANDB_STATS_RX_PACKETS]
...
}
}
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Use nf_flow_offload_tuple() to fetch flow stats, from Paul Blakey.
2) Add new xt_IDLETIMER hard mode, from Manoj Basapathi.
Follow up patch to clean up this new mode, from Dan Carpenter.
3) Add support for geneve tunnel options, from Xin Long.
4) Make sets built-in and remove modular infrastructure for sets,
from Florian Westphal.
5) Remove unused TEMPLATE_NULLS_VAL, from Li RongQing.
6) Statify nft_pipapo_get, from Chen Wandun.
7) Use C99 flexible-array member, from Gustavo A. R. Silva.
8) More descriptive variable names for bitwise, from Jeremy Sowden.
9) Four patches to add tunnel device hardware offload to the flowtable
infrastructure, from wenxu.
10) pipapo set supports for 8-bit grouping, from Stefano Brivio.
11) pipapo can switch between nibble and byte grouping, also from
Stefano.
12) Add AVX2 vectorized version of pipapo, from Stefano Brivio.
13) Update pipapo to be use it for single ranges, from Stefano.
14) Add stateful expression support to elements via control plane,
eg. counter per element.
15) Re-visit sysctls in unprivileged namespaces, from Florian Westphal.
15) Add new egress hook, from Lukas Wunner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for manipulating vlan/tunnel mappings. The
tunnel ids are globally unique and are one per-vlan. There were two
trickier issues - first in order to support vlan ranges we have to
compute the current tunnel id in the following way:
- base tunnel id (attr) + current vlan id - starting vlan id
This is in line how the old API does vlan/tunnel mapping with ranges. We
already have the vlan range present, so it's redundant to add another
attribute for the tunnel range end. It's simply base tunnel id + vlan
range. And second to support removing mappings we need an out-of-band way
to tell the option manipulating function because there are no
special/reserved tunnel id values, so we use a vlan flag to denote the
operation is tunnel mapping removal.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new option - BRIDGE_VLANDB_ENTRY_TUNNEL_ID which is used to dump
the tunnel id mapping. Since they're unique per vlan they can enter a
vlan range if they're consecutive, thus we can calculate the tunnel id
range map simply as: vlan range end id - vlan range start id. The
starting point is the tunnel id in BRIDGE_VLANDB_ENTRY_TUNNEL_ID. This
is similar to how the tunnel entries can be created in a range via the
old API (a vlan range maps to a tunnel range).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan tunnel code changes vlan options, it shouldn't touch port or
bridge options so we can constify the port argument. This would later help
us to re-use these functions from the vlan options code.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is more appropriate name as it shows the intent of why we need to
check the options' state. It also allows us to give meaning to the two
arguments of the function: the first is the current vlan (v_curr) being
checked if it could enter the range ending in the second one (range_end).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
Lastly, fix checkpatch.pl warning
WARNING: __aligned(size) is preferred over __attribute__((aligned(size)))
in net/bridge/netfilter/ebtables.c
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In br_dev_xmit() we perform vlan filtering in br_allowed_ingress() but
if the packet has the vlan header inside (e.g. bridge with disabled
tx-vlan-offload) then the vlan filtering code will use skb_vlan_untag()
to extract the vid before filtering which in turn calls pskb_may_pull()
and we may end up with a stale eth pointer. Moreover the cached eth header
pointer will generally be wrong after that operation. Remove the eth header
caching and just use eth_hdr() directly, the compiler does the right thing
and calculates it only once so we don't lose anything.
Fixes: 057658cb33 ("bridge: suppress arp pkts on BR_NEIGH_SUPPRESS ports")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
list_for_each_entry_rcu() has built-in RCU and lock checking.
Pass cond argument to list_for_each_entry_rcu() to silence
false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled
by default.
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first per-vlan option added is state, it is needed for EVPN and for
per-vlan STP. The state allows to control the forwarding on per-vlan
basis. The vlan state is considered only if the port state is forwarding
in order to avoid conflicts and be consistent. br_allowed_egress is
called only when the state is forwarding, but the ingress case is a bit
more complicated due to the fact that we may have the transition between
port:BR_STATE_FORWARDING -> vlan:BR_STATE_LEARNING which should still
allow the bridge to learn from the packet after vlan filtering and it will
be dropped after that. Also to optimize the pvid state check we keep a
copy in the vlan group to avoid one lookup. The state members are
modified with *_ONCE() to annotate the lockless access.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for option modification of single vlans and
ranges. It allows to only modify options, i.e. skip create/delete by
using the BRIDGE_VLAN_INFO_ONLY_OPTS flag. When working with a range
option changes we try to pack the notifications as much as possible.
v2: do full port (all vlans) notification only when creating/deleting
vlans for compatibility, rework the range detection when changing
options, add more verbose extack errors and check if a vlan should
be used (br_vlan_should_use checks)
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll be dumping the options for the whole range if they're equal. The
first range vlan will be used to extract the options. The commit doesn't
change anything yet it just adds the skeleton for the support. The dump
will happen when the first option is added.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we make sure that br_allowed_egress is called only when we have
BR_STATE_FORWARDING state then we can avoid a test later when we add
per-vlan state.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can notify, send a notification on add/del or change of flags.
Notifications are also compressed when possible to reduce their number
and relieve user-space of extra processing, due to that we have to
manually notify after each add/del in order to avoid double
notifications. We try hard to notify only about the vlans which actually
changed, thus a single command can result in multiple notifications
about disjoint ranges if there were vlans which didn't change inside.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new rtnetlink group for bridge vlan notifications - RTNLGRP_BRVLAN
and add support for sending vlan notifications (both single and ranges).
No functional changes intended, the notification support will be used by
later patches.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new vlandb nl attribute - BRIDGE_VLANDB_ENTRY_RANGE which causes
RTM_NEWVLAN/DELVAN to act on a range. Dumps now automatically compress
similar vlans into ranges. This will be also used when per-vlan options
are introduced and vlans' options match, they will be put into a single
range which is encapsulated in one netlink attribute. We need to run
similar checks as br_process_vlan_info() does because these ranges will
be used for options setting and they'll be able to skip
br_process_vlan_info().
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding RTM_DELVLAN support similar to RTM_NEWVLAN is simple, just need to
map DELVLAN to DELLINK and register the handler.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial RTM_NEWVLAN support which can only create vlans, operating
similar to the current br_afspec(). We will use it later to also change
per-vlan options. Old-style (flag-based) vlan ranges are not allowed
when using RTM messages, we will introduce vlan ranges later via a new
nested attribute which would allow us to have all the information about a
range encapsulated into a single nl attribute.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds vlan rtm definitions:
- NEWVLAN: to be used for creating vlans, setting options and
notifications
- DELVLAN: to be used for deleting vlans
- GETVLAN: used for dumping vlan information
Dumping vlans which can span multiple messages is added now with basic
information (vid and flags). We use nlmsg_parse() to validate the header
length in order to be able to extend the message with filtering
attributes later.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack messages on vlan processing errors. We need to move the flags
missing check after the "last" check since we may have "last" set but
lack a range end flag in the next entry.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to check if a vlan id or range are valid. The range helper
must be called when range start or end are detected.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix endianness issue in flowtable TCP flags dissector,
from Arnd Bergmann.
2) Extend flowtable test script with dnat rules, from Florian Westphal.
3) Reject padding in ebtables user entries and validate computed user
offset, reported by syzbot, from Florian Westphal.
4) Fix endianness in nft_tproxy, from Phil Sutter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
syzbot reported following splat:
BUG: KASAN: vmalloc-out-of-bounds in size_entry_mwt net/bridge/netfilter/ebtables.c:2063 [inline]
BUG: KASAN: vmalloc-out-of-bounds in compat_copy_entries+0x128b/0x1380 net/bridge/netfilter/ebtables.c:2155
Read of size 4 at addr ffffc900004461f4 by task syz-executor267/7937
CPU: 1 PID: 7937 Comm: syz-executor267 Not tainted 5.5.0-rc1-syzkaller #0
size_entry_mwt net/bridge/netfilter/ebtables.c:2063 [inline]
compat_copy_entries+0x128b/0x1380 net/bridge/netfilter/ebtables.c:2155
compat_do_replace+0x344/0x720 net/bridge/netfilter/ebtables.c:2249
compat_do_ebt_set_ctl+0x22f/0x27e net/bridge/netfilter/ebtables.c:2333
[..]
Because padding isn't considered during computation of ->buf_user_offset,
"total" is decremented by fewer bytes than it should.
Therefore, the first part of
if (*total < sizeof(*entry) || entry->next_offset < sizeof(*entry))
will pass, -- it should not have. This causes oob access:
entry->next_offset is past the vmalloced size.
Reject padding and check that computed user offset (sum of ebt_entry
structure plus all individual matches/watchers/targets) is same
value that userspace gave us as the offset of the next entry.
Reported-by: syzbot+f68108fed972453a0ad4@syzkaller.appspotmail.com
Fixes: 81e675c227 ("netfilter: ebtables: add CONFIG_COMPAT support")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This adds rx_bpdu, tx_bpdu, rx_tcn, tx_tcn, transition_blk,
transition_fwd xstats counters to the bridge ports copied over via
netlink, providing useful information for STP.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Wait for rcu grace period after releasing netns in ctnetlink,
from Florian Westphal.
2) Incorrect command type in flowtable offload ndo invocation,
from wenxu.
3) Incorrect callback type in flowtable offload flow tuple
updates, also from wenxu.
4) Fix compile warning on flowtable offload infrastructure due to
possible reference to uninitialized variable, from Nathan Chancellor.
5) Do not inline nf_ct_resolve_clash(), this is called from slow
path / stress situations. From Florian Westphal.
6) Missing IPv6 flow selector description in flowtable offload.
7) Missing check for NETDEV_UNREGISTER in nf_tables offload
infrastructure, from wenxu.
8) Update NAT selftest to use randomized netns names, from
Florian Westphal.
9) Restore nfqueue bridge support, from Marco Oliverio.
10) Compilation warning in SCTP_CHUNKMAP_*() on xt_sctp header.
From Phil Sutter.
11) Fix bogus lookup/get match for non-anonymous rbtree sets.
12) Missing netlink validation for NFT_SET_ELEM_INTERVAL_END
elements.
13) Missing netlink validation for NFT_DATA_VALUE after
nft_data_init().
14) If rule specifies no actions, offload infrastructure returns
EOPNOTSUPP.
15) Module refcount leak in object updates.
16) Missing sanitization for ARP traffic from br_netfilter, from
Eric Dumazet.
17) Compilation breakage on big-endian due to incorrect memcpy()
size in the flowtable offload infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
We have an interesting memory leak in the bridge when it is being
unregistered and is a slave to a master device which would change the
mac of its slaves on unregister (e.g. bond, team). This is a very
unusual setup but we do end up leaking 1 fdb entry because
dev_set_mac_address() would cause the bridge to insert the new mac address
into its table after all fdbs are flushed, i.e. after dellink() on the
bridge has finished and we call NETDEV_UNREGISTER the bond/team would
release it and will call dev_set_mac_address() to restore its original
address and that in turn will add an fdb in the bridge.
One fix is to check for the bridge dev's reg_state in its
ndo_set_mac_address callback and return an error if the bridge is not in
NETREG_REGISTERED.
Easy steps to reproduce:
1. add bond in mode != A/B
2. add any slave to the bond
3. add bridge dev as a slave to the bond
4. destroy the bridge device
Trace:
unreferenced object 0xffff888035c4d080 (size 128):
comm "ip", pid 4068, jiffies 4296209429 (age 1413.753s)
hex dump (first 32 bytes):
41 1d c9 36 80 88 ff ff 00 00 00 00 00 00 00 00 A..6............
d2 19 c9 5e 3f d7 00 00 00 00 00 00 00 00 00 00 ...^?...........
backtrace:
[<00000000ddb525dc>] kmem_cache_alloc+0x155/0x26f
[<00000000633ff1e0>] fdb_create+0x21/0x486 [bridge]
[<0000000092b17e9c>] fdb_insert+0x91/0xdc [bridge]
[<00000000f2a0f0ff>] br_fdb_change_mac_address+0xb3/0x175 [bridge]
[<000000001de02dbd>] br_stp_change_bridge_id+0xf/0xff [bridge]
[<00000000ac0e32b1>] br_set_mac_address+0x76/0x99 [bridge]
[<000000006846a77f>] dev_set_mac_address+0x63/0x9b
[<00000000d30738fc>] __bond_release_one+0x3f6/0x455 [bonding]
[<00000000fc7ec01d>] bond_netdev_event+0x2f2/0x400 [bonding]
[<00000000305d7795>] notifier_call_chain+0x38/0x56
[<0000000028885d4a>] call_netdevice_notifiers+0x1e/0x23
[<000000008279477b>] rollback_registered_many+0x353/0x6a4
[<0000000018ef753a>] unregister_netdevice_many+0x17/0x6f
[<00000000ba854b7a>] rtnl_delete_link+0x3c/0x43
[<00000000adf8618d>] rtnl_dellink+0x1dc/0x20a
[<000000009b6395fd>] rtnetlink_rcv_msg+0x23d/0x268
Fixes: 4359881338 ("bridge: add local MAC address to forwarding table (v2)")
Reported-by: syzbot+2add91c08eb181fea1bf@syzkaller.appspotmail.com
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We return the maximum speed of all active ports. This matches how the link
speed would give an upper limit for traffic to/from any single peer if the
bridge were replaced with a hardware switch.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
xt_in() returns NULL in the output hook, skip the pkt_type change for
that case, redirection only makes sense in broute/prerouting hooks.
Reported-by: Tom Yan <tom.ty89@gmail.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Fixes: cf3cb246e2 ("bridge: ebtables: fix reception of frames DNAT-ed to bridge device/port")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When commit df1c0b8468 ("[BRIDGE]: Packets leaking out of
disabled/blocked ports.") introduced the port state tests in
br_fdb_update() it was to avoid learning/refreshing from STP BPDUs, it was
also used to avoid learning/refreshing from user-space with NTF_USE. Those
two tests are done for every packet entering the bridge if it's learning,
but for the fast-path we already have them checked in br_handle_frame() and
is unnecessary to do it again. Thus push the checks to the unlikely cases
and drop them from br_fdb_update(), the new nbp_state_should_learn() helper
is used to determine if the port state allows br_fdb_update() to be called.
The two places which need to do it manually are:
- user-space add call with NTF_USE set
- link-local packet learning done in __br_handle_local_finish()
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking over hw-learned entries is not a likely scenario so restore the
unlikely() use for the case of SW taking over externally learned
entries.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we setup the fdb flags prior to calling fdb_create() we can avoid
two atomic bitops when learning a new entry.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we modify br_fdb_update() to take flags directly we can get rid of
one test and one atomic bitop in the learning path.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to have separate arguments for each flag, just set the flags to
whatever was passed to fdb_create() before the fdb is published.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the offloaded field to a flag and use bitops.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the added_by_external_learn field to a flag and use bitops.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Straight-forward convert of the added_by_user field to bitops.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Straight-forward convert of the is_sticky field to bitops.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the is_static to bitops, make use of the combined
test_and_set/clear_bit to simplify expressions in fdb_add_entry.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds a new fdb flags field in the hole between the two cache
lines and uses it to convert is_local to bitops.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the iph field from the state structure, which is not
properly initialized. Instead, add a new field to make the "do we want
to set DF" be the state bit and move the code to set the DF flag from
ip_frag_next().
Joint work with Pablo and Linus.
Fixes: 19c3401a91 ("net: ipv4: place control buffer handling away from fragmentation iterators")
Reported-by: Patrick Schönthaler <patrick@notvads.ovh>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas found that some forwarded packets would be stuck
in FQ packet scheduler because their skb->tstamp contained
timestamps far in the future.
We thought we addressed this point in commit 8203e2d844
("net: clear skb->tstamp in forwarding paths") but there
is still an issue when/if a packet needs to be fragmented.
In order to meet EDT requirements, we have to make sure all
fragments get the original skb->tstamp.
Note that this original skb->tstamp should be zero in
forwarding path, but might have a non zero value in
output path if user decided so.
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Thomas Bartschies <Thomas.Bartschies@cvk.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a struct definition function in nf_conntrack_bridge.h which is
not specific to conntrack and is used elswhere in netfilter. Move it
into netfilter_bridge.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Include some headers in files which require them, and remove others
which are not required.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Three netfilter headers are only included once. Inline their contents
at those sites and remove them.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent at the end.
In fact, NLMSG_DONE is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 949f1e39a6 ("bridge: mdb: notify on router port add and del")
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A kernel panic can happen if a host has disabled IPv6 on boot and have to
process guest packets (coming from a bridge) using it's ip6tables.
IPv6 packets need to be dropped if the IPv6 module is not loaded, and the
host ip6tables will be used.
Signed-off-by: Leonardo Bras <leonardo@linux.ibm.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently this simplified code snippet fails:
br_vlan_get_pvid(netdev, &pvid);
br_vlan_get_info(netdev, pvid, &vinfo);
ASSERT(!(vinfo.flags & BRIDGE_VLAN_INFO_PVID));
It is intuitive that the pvid of a netdevice should have the
BRIDGE_VLAN_INFO_PVID flag set.
However I can't seem to pinpoint a commit where this behavior was
introduced. It seems like it's been like that since forever.
At a first glance it would make more sense to just handle the
BRIDGE_VLAN_INFO_PVID flag in __vlan_add_flags. However, as Nikolay
explains:
There are a few reasons why we don't do it, most importantly because
we need to have only one visible pvid at any single time, even if it's
stale - it must be just one. Right now that rule will not be violated
by this change, but people will try using this flag and could see two
pvids simultaneously. You can see that the pvid code is even using
memory barriers to propagate the new value faster and everywhere the
pvid is read only once. That is the reason the flag is set
dynamically when dumping entries, too. A second (weaker) argument
against would be given the above we don't want another way to do the
same thing, specifically if it can provide us with two pvids (e.g. if
walking the vlan list) or if it can provide us with a pvid different
from the one set in the vg. [Obviously, I'm talking about RCU
pvid/vlan use cases similar to the dumps. The locked cases are fine.
I would like to avoid explaining why this shouldn't be relied upon
without locking]
So instead of introducing the above change and making sure of the pvid
uniqueness under RCU, simply dynamically populate the pvid flag in
br_vlan_get_info().
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the vlan_proto of ingress bridge in network byteorder as userspace
expects. Otherwise this is inconsistent with NFT_META_PROTOCOL.
Fixes: 2a3a93ef0b ("netfilter: nft_meta_bridge: Add NFT_META_BRI_IIFVPROTO support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The ordering of arguments to the x_tables ADD_COUNTER macro
appears to be wrong in ebtables (cf. ip_tables.c, ip6_tables.c,
and arp_tables.c).
This causes data corruption in the ebtables userspace tools
because they get incorrect packet & byte counts from the kernel.
Fixes: d72133e628 ("netfilter: ebtables: use ADD_COUNTER macro")
Signed-off-by: Todd Seidelmann <tseidelmann@linode.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently this is needed only for user-space compatibility, so similar
object adds/deletes as the dumped ones would succeed. Later it can be
used for L2 mcast MAC add/delete.
v3: fix compiler warning (DaveM)
v2: don't send a notification when used from user-space, arm the group
timer if no ports are left after host entry del
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we dump only the port mdb entries but we can have host-joined
entries on the bridge itself and they should be treated as normal temp
mdbs, they're already notified:
$ bridge monitor all
[MDB]dev br0 port br0 grp ff02::8 temp
The group will not be shown in the bridge mdb output, but it takes 1 slot
and it's timing out. If it's only host-joined then the mdb show output
can even be empty.
After this patch we show the host-joined groups:
$ bridge mdb show
dev br0 port br0 grp ff02::8 temp
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to factor out the mdb fill portion in order to re-use it later for
the bridge mdb entries. No functional changes intended.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial patch to move the vlan comments in their proper places above the
vid 0 checks.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the bridge device's vlan init bugs come from the fact that its
default pvid is created at the wrong time, way too early in ndo_init()
before the device is even assigned an ifindex. It introduces a bug when the
bridge's dev_addr is added as fdb during the initial default pvid creation
the notification has ifindex/NDA_MASTER both equal to 0 (see example below)
which really makes no sense for user-space[0] and is wrong.
Usually user-space software would ignore such entries, but they are
actually valid and will eventually have all necessary attributes.
It makes much more sense to send a notification *after* the device has
registered and has a proper ifindex allocated rather than before when
there's a chance that the registration might still fail or to receive
it with ifindex/NDA_MASTER == 0. Note that we can remove the fdb flush
from br_vlan_flush() since that case can no longer happen. At
NETDEV_REGISTER br->default_pvid is always == 1 as it's initialized by
br_vlan_init() before that and at NETDEV_UNREGISTER it can be anything
depending why it was called (if called due to NETDEV_REGISTER error
it'll still be == 1, otherwise it could be any value changed during the
device life time).
For the demonstration below a small change to iproute2 for printing all fdb
notifications is added, because it contained a workaround not to show
entries with ifindex == 0.
Command executed while monitoring: $ ip l add br0 type bridge
Before (both ifindex and master == 0):
$ bridge monitor fdb
36:7e:8a:b3:56:ba dev * vlan 1 master * permanent
After (proper br0 ifindex):
$ bridge monitor fdb
e6:2a:ae:7a:b7:48 dev br0 vlan 1 master br0 permanent
v4: move only the default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
v3: send the correct v2 patch with all changes (stub should return 0)
v2: on error in br_vlan_init set br->vlgrp to NULL and return 0 in
the br_vlan_bridge_event stub when bridge vlans are disabled
[0] https://bugzilla.kernel.org/show_bug.cgi?id=204389
Reported-by: michael-dev <michael-dev@fami-braun.de>
Fixes: 5be5a2df40 ("bridge: Add filtering support for default_pvid")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In user-space there's no way to distinguish why an mdb entry was deleted
and that is a problem for daemons which would like to keep the mdb in
sync with remote ends (e.g. mlag) but would also like to converge faster.
In almost all cases we'd like to age-out the remote entry for performance
and convergence reasons except when fast-leave is enabled. In that case we
want explicit immediate remote delete, thus add mdb flag which is set only
when the entry is being deleted due to fast-leave.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When permanent entries were introduced by the commit below, they were
exempt from timing out and thus igmp leave wouldn't affect them unless
fast leave was enabled on the port which was added before permanent
entries existed. It shouldn't matter if fast leave is enabled or not
if the user added a permanent entry it shouldn't be deleted on igmp
leave.
Before:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
< join and leave 229.1.1.1 on eth4 >
$ bridge mdb show
$
After:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
< join and leave 229.1.1.1 on eth4 >
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
Fixes: ccb1c31a7a ("bridge: add flags to distinguish permanent mdb entires")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree:
1) memleak in ebtables from the error path for the 32/64 compat layer,
from Florian Westphal.
2) Fix inverted meta ifname/ifidx matching when no interface is set
on either from the input/output path, from Phil Sutter.
3) Remove goto label in nft_meta_bridge, also from Phil.
4) Missing include guard in xt_connlabel, from Masahiro Yamada.
5) Two patch to fix ipset destination MAC matching coming from
Stephano Brivio, via Jozsef Kadlecsik.
6) Fix set rename and listing concurrency problem, from Shijie Luo.
Patch also coming via Jozsef Kadlecsik.
7) ebtables 32/64 compat missing base chain policy in rule count,
from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ebtables doesn't include the base chain policies in the rule count,
so we need to add them manually when we call into the x_tables core
to allocate space for the comapt offset table.
This lead syzbot to trigger:
WARNING: CPU: 1 PID: 9012 at net/netfilter/x_tables.c:649
xt_compat_add_offset.cold+0x11/0x36 net/netfilter/x_tables.c:649
Reported-by: syzbot+276ddebab3382bbf72db@syzkaller.appspotmail.com
Fixes: 2035f3ff8e ("netfilter: ebtables: compat: un-break 32bit setsockopt when no rules are present")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On initialization failure we have to delete the local fdb which was
inserted due to the default pvid creation. This problem has been present
since the inception of default_pvid. Note that currently there are 2 cases:
1) in br_dev_init() when br_multicast_init() fails
2) if register_netdevice() fails after calling ndo_init()
This patch takes care of both since br_vlan_flush() is called on both
occasions. Also the new fdb delete would be a no-op on normal bridge
device destruction since the local fdb would've been already flushed by
br_dev_delete(). This is not an issue for ports since nbp_vlan_init() is
called last when adding a port thus nothing can fail after it.
Reported-by: syzbot+88533dc8b582309bf3ee@syzkaller.appspotmail.com
Fixes: 5be5a2df40 ("bridge: Add filtering support for default_pvid")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The label is used just once and the code it points at is not reused, no
point in keeping it.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nft_meta_get_eval()'s tendency to bail out setting NFT_BREAK verdict in
situations where required data is missing leads to unexpected behaviour
with inverted checks like so:
| meta iifname != eth0 accept
This rule will never match if there is no input interface (or it is not
known) which is not intuitive and, what's worse, breaks consistency of
iptables-nft with iptables-legacy.
Fix this by falling back to placing a value in dreg which never matches
(avoiding accidental matches), i.e. zero for interface index and an
empty string for interface name.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In compat_do_replace(), a temporary buffer is allocated through vmalloc()
to hold entries copied from the user space. The buffer address is firstly
saved to 'newinfo->entries', and later on assigned to 'entries_tmp'. Then
the entries in this temporary buffer is copied to the internal kernel
structure through compat_copy_entries(). If this copy process fails,
compat_do_replace() should be terminated. However, the allocated temporary
buffer is not freed on this path, leading to a memory leak.
To fix the bug, free the buffer before returning from compat_do_replace().
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The new nft_meta_bridge code fails to link as built-in when NF_TABLES
is a loadable module.
net/bridge/netfilter/nft_meta_bridge.o: In function `nft_meta_bridge_get_eval':
nft_meta_bridge.c:(.text+0x1e8): undefined reference to `nft_meta_get_eval'
net/bridge/netfilter/nft_meta_bridge.o: In function `nft_meta_bridge_get_init':
nft_meta_bridge.c:(.text+0x468): undefined reference to `nft_meta_get_init'
nft_meta_bridge.c:(.text+0x49c): undefined reference to `nft_parse_register'
nft_meta_bridge.c:(.text+0x4cc): undefined reference to `nft_validate_register_store'
net/bridge/netfilter/nft_meta_bridge.o: In function `nft_meta_bridge_module_exit':
nft_meta_bridge.c:(.exit.text+0x14): undefined reference to `nft_unregister_expr'
net/bridge/netfilter/nft_meta_bridge.o: In function `nft_meta_bridge_module_init':
nft_meta_bridge.c:(.init.text+0x14): undefined reference to `nft_register_expr'
net/bridge/netfilter/nft_meta_bridge.o:(.rodata+0x60): undefined reference to `nft_meta_get_dump'
net/bridge/netfilter/nft_meta_bridge.o:(.rodata+0x88): undefined reference to `nft_meta_set_eval'
This can happen because the NF_TABLES_BRIDGE dependency itself is just a
'bool'. Make the symbol a 'tristate' instead so Kconfig can propagate the
dependencies correctly.
Fixes: 30e103fe24 ("netfilter: nft_meta: move bridge meta keys into nft_meta_bridge")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Place NF_CONNTRACK_BRIDGE away from the NF_TABLES_BRIDGE dependency.
Fixes: 3c171f496e ("netfilter: bridge: add connection tracking system")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
This patch allows you to match on bridge vlan protocol, eg.
nft add rule bridge firewall zones counter meta ibrvproto 0x8100
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This new function allows you to fetch the bridge port vlan protocol.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch allows you to match on the bridge port pvid, eg.
nft add rule bridge firewall zones counter meta ibrpvid 10
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This new function allows you to fetch bridge pvid from packet path.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
nft_bridge_meta should not access the bridge internal API.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Separate bridge meta key from nft_meta to meta_bridge to avoid a
dependency between the bridge module and nft_meta when using the bridge
API available through include/linux/if_bridge.h
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Don't cache eth dest pointer before calling pskb_may_pull.
Fixes: cf0f02d04a ("[BRIDGE]: use llc for receiving STP packets")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would cache ether dst pointer on input in br_handle_frame_finish but
after the neigh suppress code that could lead to a stale pointer since
both ipv4 and ipv6 suppress code do pskb_may_pull. This means we have to
always reload it after the suppress code so there's no point in having
it cached just retrieve it directly.
Fixes: 057658cb33 ("bridge: suppress arp pkts on BR_NEIGH_SUPPRESS ports")
Fixes: ed842faeb2 ("bridge: suppress nd pkts on BR_NEIGH_SUPPRESS ports")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a pointer to the ipv6 hdr in br_ip6_multicast_query but we may
call pskb_may_pull afterwards and end up using a stale pointer.
So use the header directly, it's just 1 place where it's needed.
Fixes: 08b202b672 ("bridge br_multicast: IPv6 MLD support.")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Martin Weinelt <martin@linuxlounge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve conflict between d2912cb15b ("treewide: Replace GPLv2
boilerplate/reference with SPDX - rule 500") removing the GPL disclaimer
and fe03d47456 ("Update my email address") which updates Jozsef
Kadlecsik's email.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ip netns exec ns1 ip a a dev eth0 10.0.0.7/24
ip netns exec ns2 ip link a link eth0 name vlan type vlan id 200
ip netns exec ns2 ip a a dev vlan 10.0.0.8/24
ip l add dev br0 type bridge vlan_filtering 1
brctl addif br0 veth1
brctl addif br0 veth2
bridge vlan add dev veth1 vid 200 pvid untagged
bridge vlan add dev veth2 vid 200
A two fragment packet sent from ns2 contains the vlan tag 200. In the
bridge conntrack, this packet will defrag to one skb with fraglist.
When the packet is forwarded to ns1 through veth1, the first skb vlan
tag will be cleared by the "untagged" flags. But the vlan tag in the
second skb is still tagged, so the second fragment ends up with tag 200
to ns1. So if the first fragment packet doesn't contain the vlan tag,
all of the remain should not contain vlan tag.
Fixes: 3c171f496e ("netfilter: bridge: add connection tracking system")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Prevent a UAF in brnf_exit_net().
When unregister_net_sysctl_table() is called the ctl_hdr pointer will
obviously be freed and so accessing it righter after is invalid. Fix
this by stashing a pointer to the table we want to free before we
unregister the sysctl header.
Note that syzkaller falsely chased this down to the drm tree so the
Fixes tag that syzkaller requested would be wrong. This commit uses a
different but the correct Fixes tag.
/* Splat */
BUG: KASAN: use-after-free in br_netfilter_sysctl_exit_net
net/bridge/br_netfilter_hooks.c:1121 [inline]
BUG: KASAN: use-after-free in brnf_exit_net+0x38c/0x3a0
net/bridge/br_netfilter_hooks.c:1141
Read of size 8 at addr ffff8880a4078d60 by task kworker/u4:4/8749
CPU: 0 PID: 8749 Comm: kworker/u4:4 Not tainted 5.2.0-rc5-next-20190618 #17
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
01/01/2011
Workqueue: netns cleanup_net
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0xd4/0x306 mm/kasan/report.c:351
__kasan_report.cold+0x1b/0x36 mm/kasan/report.c:482
kasan_report+0x12/0x20 mm/kasan/common.c:614
__asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132
br_netfilter_sysctl_exit_net net/bridge/br_netfilter_hooks.c:1121 [inline]
brnf_exit_net+0x38c/0x3a0 net/bridge/br_netfilter_hooks.c:1141
ops_exit_list.isra.0+0xaa/0x150 net/core/net_namespace.c:154
cleanup_net+0x3fb/0x960 net/core/net_namespace.c:553
process_one_work+0x989/0x1790 kernel/workqueue.c:2269
worker_thread+0x98/0xe40 kernel/workqueue.c:2415
kthread+0x354/0x420 kernel/kthread.c:255
ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352
Allocated by task 11374:
save_stack+0x23/0x90 mm/kasan/common.c:71
set_track mm/kasan/common.c:79 [inline]
__kasan_kmalloc mm/kasan/common.c:489 [inline]
__kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:462
kasan_kmalloc+0x9/0x10 mm/kasan/common.c:503
__do_kmalloc mm/slab.c:3645 [inline]
__kmalloc+0x15c/0x740 mm/slab.c:3654
kmalloc include/linux/slab.h:552 [inline]
kzalloc include/linux/slab.h:743 [inline]
__register_sysctl_table+0xc7/0xef0 fs/proc/proc_sysctl.c:1327
register_net_sysctl+0x29/0x30 net/sysctl_net.c:121
br_netfilter_sysctl_init_net net/bridge/br_netfilter_hooks.c:1105 [inline]
brnf_init_net+0x379/0x6a0 net/bridge/br_netfilter_hooks.c:1126
ops_init+0xb3/0x410 net/core/net_namespace.c:130
setup_net+0x2d3/0x740 net/core/net_namespace.c:316
copy_net_ns+0x1df/0x340 net/core/net_namespace.c:439
create_new_namespaces+0x400/0x7b0 kernel/nsproxy.c:103
unshare_nsproxy_namespaces+0xc2/0x200 kernel/nsproxy.c:202
ksys_unshare+0x444/0x980 kernel/fork.c:2822
__do_sys_unshare kernel/fork.c:2890 [inline]
__se_sys_unshare kernel/fork.c:2888 [inline]
__x64_sys_unshare+0x31/0x40 kernel/fork.c:2888
do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 9:
save_stack+0x23/0x90 mm/kasan/common.c:71
set_track mm/kasan/common.c:79 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/common.c:451
kasan_slab_free+0xe/0x10 mm/kasan/common.c:459
__cache_free mm/slab.c:3417 [inline]
kfree+0x10a/0x2c0 mm/slab.c:3746
__rcu_reclaim kernel/rcu/rcu.h:215 [inline]
rcu_do_batch kernel/rcu/tree.c:2092 [inline]
invoke_rcu_callbacks kernel/rcu/tree.c:2310 [inline]
rcu_core+0xcc7/0x1500 kernel/rcu/tree.c:2291
__do_softirq+0x25c/0x94c kernel/softirq.c:292
The buggy address belongs to the object at ffff8880a4078d40
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 32 bytes inside of
512-byte region [ffff8880a4078d40, ffff8880a4078f40)
The buggy address belongs to the page:
page:ffffea0002901e00 refcount:1 mapcount:0 mapping:ffff8880aa400a80
index:0xffff8880a40785c0
flags: 0x1fffc0000000200(slab)
raw: 01fffc0000000200 ffffea0001d636c8 ffffea0001b07308 ffff8880aa400a80
raw: ffff8880a40785c0 ffff8880a40780c0 0000000100000004 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8880a4078c00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880a4078c80: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
> ffff8880a4078d00: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
^
ffff8880a4078d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880a4078e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Reported-by: syzbot+43a3fa52c0d9c5c94f41@syzkaller.appspotmail.com
Fixes: 22567590b2 ("netfilter: bridge: namespace bridge netfilter sysctls")
Signed-off-by: Christian Brauner <christian@brauner.io>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the /proc/sys/net/bridge folder is only created in the initial
network namespace. This patch ensures that the /proc/sys/net/bridge folder
is available in each network namespace if the module is loaded and
disappears from all network namespaces when the module is unloaded.
In doing so the patch makes the sysctls:
bridge-nf-call-arptables
bridge-nf-call-ip6tables
bridge-nf-call-iptables
bridge-nf-filter-pppoe-tagged
bridge-nf-filter-vlan-tagged
bridge-nf-pass-vlan-input-dev
apply per network namespace. This unblocks some use-cases where users would
like to e.g. not do bridge filtering for bridges in a specific network
namespace while doing so for bridges located in another network namespace.
The netfilter rules are afaict already per network namespace so it should
be safe for users to specify whether bridge devices inside a network
namespace are supposed to go through iptables et al. or not. Also, this can
already be done per-bridge by setting an option for each individual bridge
via Netlink. It should also be possible to do this for all bridges in a
network namespace via sysctls.
Cc: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This ports the sysctls to use struct brnf_net.
With this patch we make it possible to namespace the br_netfilter module in
the following patch.
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The kbuild documentation clearly shows that the documents
there are written at different times: some use markdown,
some use their own peculiar logic to split sections.
Convert everything to ReST without affecting too much
the author's style and avoiding adding uneeded markups.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in the day, skb_ensure_writable did not exist. By now, both functions
have the same precondition:
I. skb_make_writable will test in this order:
1. wlen > skb->len -> error
2. if not cloned and wlen <= headlen -> OK
3. If cloned and wlen bytes of clone writeable -> OK
After those checks, skb is either not cloned but needs to pull from
nonlinear area, or writing to head would also alter data of another clone.
In both cases skb_make_writable will then call __pskb_pull_tail, which will
kmalloc a new memory area to use for skb->head.
IOW, after successful skb_make_writable call, the requested length is in
linear area and can be modified, even if skb was cloned.
II. skb_ensure_writable will do this instead:
1. call pskb_may_pull. This handles case 1 above.
After this, wlen is in linear area, but skb might be cloned.
2. return if skb is not cloned
3. return if wlen byte of clone are writeable.
4. fully copy the skb.
So post-conditions are the same:
*len bytes are writeable in linear area without altering any payload data
of a clone, all header pointers might have been changed.
Only differences are that skb_ensure_writable is in the core, whereas
skb_make_writable lives in netfilter core and the inverted return value.
skb_make_writable returns 0 on error, whereas skb_ensure_writable returns
negative value.
For the normal cases performance is similar:
A. skb is not cloned and in linear area:
pskb_may_pull is inline helper, so neither function copies.
B. skb is cloned, write is in linear area and clone is writeable:
both funcions return with step 3.
This series removes skb_make_writable from the kernel.
While at it, pass the needed value instead, its less confusing that way:
There is no special-handling of "0-length" argument in either
skb_make_writable or skb_ensure_writable.
bridge already makes sure ethernet header is in linear area, only purpose
of the make_writable() is is to copy skb->head in case of cloned skbs.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
br_defrag() and br_fragment() indirections are added in case that IPv6
support comes as a module, to avoid pulling innecessary dependencies in.
The new fraglist iterator and fragment transformer APIs are used to
implement the refragmentation code.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic connection tracking support for the bridge,
including initial IPv4 support.
This patch register two hooks to deal with the bridge forwarding path,
one from the bridge prerouting hook to call nf_conntrack_in(); and
another from the bridge postrouting hook to confirm the entry.
The conntrack bridge prerouting hook defragments packets before passing
them to nf_conntrack_in() to look up for an existing entry, otherwise a
new entry is allocated and it is attached to the skbuff. The conntrack
bridge postrouting hook confirms new conntrack entries, ie. if this is
the first packet seen, then it adds the entry to the hashtable and (if
needed) it refragments the skbuff into the original fragments, leaving
the geometry as is if possible. Exceptions are linearized skbuffs, eg.
skbuffs that are passed up to nfqueue and conntrack helpers, as well as
cloned skbuff for the local delivery (eg. tcpdump), also in case of
bridge port flooding (cloned skbuff too).
The packet defragmentation is done through the ip_defrag() call. This
forces us to save the bridge control buffer, reset the IP control buffer
area and then restore it after call. This function also bumps the IP
fragmentation statistics, it would be probably desiderable to have
independent statistics for the bridge defragmentation/refragmentation.
The maximum fragment length is stored in the control buffer and it is
used to refragment the skbuff from the postrouting path.
The new fraglist splitter and fragment transformer APIs are used to
implement the bridge refragmentation code. The br_ip_fragment() function
drops the packet in case the maximum fragment size seen is larger than
the output port MTU.
This patchset follows the principle that conntrack should not drop
packets, so users can do it through policy via invalid state matching.
Like br_netfilter, there is no refragmentation for packets that are
passed up for local delivery, ie. prerouting -> input path. There are
calls to nf_reset() already in several spots in the stack since time ago
already, eg. af_packet, that show that skbuff fraglist handling from the
netif_rx path is supported already.
The helpers are called from the postrouting hook, before confirmation,
from there we may see packet floods to bridge ports. Then, although
unlikely, this may result in exercising the helpers many times for each
clone. It would be good to explore how to pass all the packets in a list
to the conntrack hook to do this handle only once for this case.
Thanks to Florian Westphal for handing me over an initial patchset
version to add support for conntrack bridge.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Postpone chain policy update to drop after transaction is complete,
from Florian Westphal.
2) Add entry to flowtable after confirmation to fix UDP flows with
packets going in one single direction.
3) Reference count leak in dst object, from Taehee Yoo.
4) Check for TTL field in flowtable datapath, from Taehee Yoo.
5) Fix h323 conntrack helper due to incorrect boundary check,
from Jakub Jankowski.
6) Fix incorrect rcu dereference when fetching basechain stats,
from Florian Westphal.
7) Missing error check when adding new entries to flowtable,
from Taehee Yoo.
8) Use version field in nfnetlink message to honor the nfgen_family
field, from Kristian Evensen.
9) Remove incorrect configuration check for CONFIG_NF_CONNTRACK_IPV6,
from Subash Abhinov Kasiviswanathan.
10) Prevent dying entries from being added to the flowtable,
from Taehee Yoo.
11) Don't hit WARN_ON() with malformed blob in ebtables with
trailing data after last rule, reported by syzbot, patch
from Florian Westphal.
12) Remove NFT_CT_TIMEOUT enumeration, never used in the kernel
code.
13) Fix incorrect definition for NFT_LOGLEVEL_MAX, from Florian
Westphal.
This batch comes with a conflict that can be fixed with this patch:
diff --cc include/uapi/linux/netfilter/nf_tables.h
index 7bdb234f3d8c,f0cf7b0f4f35..505393c6e959
--- a/include/uapi/linux/netfilter/nf_tables.h
+++ b/include/uapi/linux/netfilter/nf_tables.h
@@@ -966,6 -966,8 +966,7 @@@ enum nft_socket_keys
* @NFT_CT_DST_IP: conntrack layer 3 protocol destination (IPv4 address)
* @NFT_CT_SRC_IP6: conntrack layer 3 protocol source (IPv6 address)
* @NFT_CT_DST_IP6: conntrack layer 3 protocol destination (IPv6 address)
- * @NFT_CT_TIMEOUT: connection tracking timeout policy assigned to conntrack
+ * @NFT_CT_ID: conntrack id
*/
enum nft_ct_keys {
NFT_CT_STATE,
@@@ -991,6 -993,8 +992,7 @@@
NFT_CT_DST_IP,
NFT_CT_SRC_IP6,
NFT_CT_DST_IP6,
- NFT_CT_TIMEOUT,
+ NFT_CT_ID,
__NFT_CT_MAX
};
#define NFT_CT_MAX (__NFT_CT_MAX - 1)
That replaces the unused NFT_CT_TIMEOUT definition by NFT_CT_ID. If you prefer,
I can also solve this conflict here, just let me know.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently error return from kobject_init_and_add() is not followed by a
call to kobject_put(). This means there is a memory leak. We currently
set p to NULL so that kfree() may be called on it as a noop, the code is
arguably clearer if we move the kfree() up closer to where it is
called (instead of after goto jump).
Remove a goto label 'err1' and jump to call to kobject_put() in error
return from kobject_init_and_add() fixing the memory leak. Re-name goto
label 'put_back' to 'err1' now that we don't use err1, following current
nomenclature (err1, err2 ...). Move call to kfree out of the error
code at bottom of function up to closer to where memory was allocated.
Add comment to clarify call to kfree().
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If userspace provides a rule blob with trailing data after last target,
we trigger a splat, then convert ruleset to 64bit format (with trailing
data), then pass that to do_replace_finish() which then returns -EINVAL.
Erroring out right away avoids the splat plus unneeded translation and
error unwind.
Fixes: 81e675c227 ("netfilter: ebtables: add CONFIG_COMPAT support")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a simple cleanup addressing two coding style issues found by
checkpatch.pl in an earlier patch. It's submitted as a separate patch to
keep the original patch as it was generated by spatch.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) Add a selftest for icmp packet too big errors with conntrack, from
Florian Westphal.
2) Validate inner header in ICMP error message does not lie to us
in conntrack, also from Florian.
3) Initialize ct->timeout to calm down KASAN, from Alexander Potapenko.
4) Skip ICMP error messages from tunnels in IPVS, from Julian Anastasov.
5) Use a hash to expose conntrack and expectation ID, from Florian Westphal.
6) Prevent shift wrap in nft_chain_parse_hook(), from Dan Carpenter.
7) Fix broken ICMP ID randomization with NAT, also from Florian.
8) Remove WARN_ON in ebtables compat that is reached via syzkaller,
from Florian Westphal.
9) Fix broken timestamps since fb420d5d91 ("tcp/fq: move back to
CLOCK_MONOTONIC"), from Florian.
10) Fix logging of invalid packets in conntrack, from Andrei Vagin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It means userspace gave us a ruleset where there is some other
data after the ebtables target but before the beginning of the next rule.
Fixes: 81e675c227 ("netfilter: ebtables: add CONFIG_COMPAT support")
Reported-by: syzbot+659574e7bcc7f7eb4df7@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If vlan bridge binding is enabled, then the link state of a vlan device
that is an upper device of the bridge tracks the state of bridge ports
that are members of that vlan. But this can only be done when the link
state of the bridge is up. If it is down, then the link state of the
vlan devices must also be down. This is to maintain existing behavior
for when STP is enabled and there are no live ports, in which case the
link state for the bridge and any vlan devices is down.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If vlan bridge binding is enabled, then the link state of a vlan device
that is an upper device of the bridge should track the state of bridge
ports that are members of that vlan. So if a bridge port becomes or
stops being a member of a vlan, then update the link state of the
vlan device if necessary.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of vlan filtering on bridges, the bridge may also have the
corresponding vlan devices as upper devices. A vlan bridge binding mode
is added to allow the link state of the vlan device to track only the
state of the subset of bridge ports that are also members of the vlan,
rather than that of all bridge ports. This mode is set with a vlan flag
rather than a bridge sysfs so that the 8021q module is aware that it
should not set the link state for the vlan device.
If bridge vlan is configured, the bridge device event handling results
in the link state for an upper device being set, if it is a vlan device
with the vlan bridge binding mode enabled. This also sets a
vlan_bridge_binding flag so that subsequent UP/DOWN/CHANGE events for
the ports in that bridge result in a link state update of the vlan
device if required.
The link state of the vlan device is up if there is at least one bridge
port that is a vlan member that is admin & oper up, otherwise its oper
state is IF_OPER_LOWERLAYERDOWN.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the introduction of the vlan_stats_per_port option the netlink
export of it has been broken since I made a typo and used the ifla
attribute instead of the bridge option to retrieve its state.
Sysfs export is fine, only netlink export has been affected.
Fixes: 9163a0fc1f ("net: bridge: add support for per-port vlan stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the commit below was introduced it changed two visible things:
- the skb was no longer passed through the protocol handlers with the
original device
- the skb was passed up the stack with skb->dev = bridge
The first change broke af_packet sockets on bridge ports. For example we
use them for hostapd which listens for ETH_P_PAE packets on the ports.
We discussed two possible fixes:
- create a clone and pass it through NF_HOOK(), act on the original skb
based on the result
- somehow signal to the caller from the okfn() that it was called,
meaning the skb is ok to be passed, which this patch is trying to
implement via returning 1 from the bridge link-local okfn()
Note that we rely on the fact that NF_QUEUE/STOLEN would return 0 and
drop/error would return < 0 thus the okfn() is called only when the
return was 1, so we signal to the caller that it was called by preserving
the return value from nf_hook().
Fixes: 8626c56c82 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After merging the netfilter-next tree, today's linux-next build (powerpc
ppc44x_defconfig) failed like this:
In file included from net/bridge/br_input.c:19:
include/net/netfilter/nf_queue.h:16:23: error: field 'state' has incomplete type
struct nf_hook_state state;
^~~~~
Fixes: 971502d77f ("bridge: netfilter: unroll NF_HOOK helper in bridge input path")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This makes broute a normal ebtables table, hooking at PREROUTING.
The broute hook is removed.
It uses skb->cb to signal to bridge rx handler that the skb should be
routed instead of being bridged.
This change is backwards compatible with ebtables as no userspace visible
parts are changed.
This means we can also remove the !ops test in ebt_register_table,
it was only there for broute table sake.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Replace NF_HOOK() based invocation of the netfilter hooks with a private
copy of nf_hook_slow().
This copy has one difference: it can return the rx handler value expected
by the stack, i.e. RX_HANDLER_CONSUMED or RX_HANDLER_PASS.
This is needed by the next patch to invoke the ebtables
"broute" table via the standard netfilter hooks rather than the custom
"br_should_route_hook" indirection that is used now.
When the skb is to be "brouted", we must return RX_HANDLER_PASS from the
bridge rx input handler, but there is no way to indicate this via
NF_HOOK(), unless perhaps by some hack such as exposing bridge_cb in the
netfilter core or a percpu flag.
text data bss dec filename
3369 56 0 3425 net/bridge/br_input.o.before
3458 40 0 3498 net/bridge/br_input.o.after
This allows removal of the "br_should_route_hook" in the next patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reduce size of br_input_skb_cb from 24 to 16 bytes by
using bitfield for those values that can only be 0 or 1.
igmp is the igmp type value, so it needs to be at least u8.
Furthermore, the bridge currently relies on step-by-step initialization
of br_input_skb_cb fields as the skb passes through the stack.
Explicitly zero out the bridge input cb instead, this avoids having to
review/validate that no BR_INPUT_SKB_CB(skb)->foo test can see a
'random' value from previous protocol cb.
AFAICS all current fields are always set up before they are read again,
so this is not a bug fix.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
br_multicast_start_querier() walks over the port list but it can be
called from a timer with only multicast_lock held which doesn't protect
the port list, so use RCU to walk over it.
Fixes: c83b8fab06 ("bridge: Restart queries when last querier expires")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes rhashtables to use a bit_spin_lock on BIT(1) of the
bucket pointer to lock the hash chain for that bucket.
The benefits of a bit spin_lock are:
- no need to allocate a separate array of locks.
- no need to have a configuration option to guide the
choice of the size of this array
- locking cost is often a single test-and-set in a cache line
that will have to be loaded anyway. When inserting at, or removing
from, the head of the chain, the unlock is free - writing the new
address in the bucket head implicitly clears the lock bit.
For __rhashtable_insert_fast() we ensure this always happens
when adding a new key.
- even when lockings costs 2 updates (lock and unlock), they are
in a cacheline that needs to be read anyway.
The cost of using a bit spin_lock is a little bit of code complexity,
which I think is quite manageable.
Bit spin_locks are sometimes inappropriate because they are not fair -
if multiple CPUs repeatedly contend of the same lock, one CPU can
easily be starved. This is not a credible situation with rhashtable.
Multiple CPUs may want to repeatedly add or remove objects, but they
will typically do so at different buckets, so they will attempt to
acquire different locks.
As we have more bit-locks than we previously had spinlocks (by at
least a factor of two) we can expect slightly less contention to
go with the slightly better cache behavior and reduced memory
consumption.
To enhance type checking, a new struct is introduced to represent the
pointer plus lock-bit
that is stored in the bucket-table. This is "struct rhash_lock_head"
and is empty. A pointer to this needs to be cast to either an
unsigned lock, or a "struct rhash_head *" to be useful.
Variables of this type are most often called "bkt".
Previously "pprev" would sometimes point to a bucket, and sometimes a
->next pointer in an rhash_head. As these are now different types,
pprev is NULL when it would have pointed to the bucket. In that case,
'blk' is used, together with correct locking protocol.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mcast conversion to rhashtable this function has been unused, so
remove it.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be careful and always zero the whole br_ip struct when it is
used for matching since the rhashtable change. This patch fixes all the
places which didn't properly clear it which in turn might've caused
mismatches.
Thanks for the great bug report with reproducing steps and bisection.
Steps to reproduce (from the bug report):
ip link add br0 type bridge mcast_querier 1
ip link set br0 up
ip link add v2 type veth peer name v3
ip link set v2 master br0
ip link set v2 up
ip link set v3 up
ip addr add 3.0.0.2/24 dev v3
ip netns add test
ip link add v1 type veth peer name v1 netns test
ip link set v1 master br0
ip link set v1 up
ip -n test link set v1 up
ip -n test addr add 3.0.0.1/24 dev v1
# Multicast receiver
ip netns exec test socat
UDP4-RECVFROM:5588,ip-add-membership=224.224.224.224:3.0.0.1,fork -
# Multicast sender
echo hello | nc -u -s 3.0.0.2 224.224.224.224 5588
Reported-by: liam.mcbirnie@boeing.com
Fixes: 19e3a9c90c ("net: bridge: convert multicast to generic rhashtable")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can optimize the fdb convergence when a backup_port is present by not
immediately flushing the entries of the stopped port since traffic for
those entries will flow towards the backup_port.
There are 2 cases specifically that benefit most:
- when the stopped port comes up before the entries expire by themselves
- when there's an external entry refresh and they're kept while the
backup_port is operating (e.g. mlag)
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify this code by updating bridge multicast stats from
maybe_deliver().
Note that commit 6db6f0eae6 ("bridge: multicast to unicast"), in case
the port flag BR_MULTICAST_TO_UNICAST is set, never updates the previous
port pointer, therefore it is always going to be different from the
existing port in this deduplicated list iteration.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the br_port_exists() macro with its twin from netdevice.h
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of stubs is growing and has nothing to do with addrconf.
Move the definition of the stubs to a separate header file and update
users. In the move, drop the vxlan specific comment before ipv6_stub.
Code move only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to use eth_broadcast_addr() to assign broadcast address
insetad of memset().
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Commit 21d1196a35 ("ipv4: set transport header earlier"),
skb->transport_header has been always set before entering INET
netfilter. This patch is to set skb->transport_header for bridge
before entering INET netfilter by bridge-nf-call-iptables.
It also fixes an issue that sctp_error() couldn't compute a right
csum due to unset skb->transport_header.
Fixes: e6d8b64b34 ("net: sctp: fix and consolidate SCTP checksumming code")
Reported-by: Li Shuang <shuali@redhat.com>
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Add .release_ops to properly unroll .select_ops, use it from nft_compat.
After this change, we can remove list of extensions too to simplify this
codebase.
2) Update amanda conntrack helper to support v3.4, from Florian Tham.
3) Get rid of the obsolete BUGPRINT macro in ebtables, from
Florian Westphal.
4) Merge IPv4 and IPv6 masquerading infrastructure into one single module.
From Florian Westphal.
5) Patchset to remove nf_nat_l3proto structure to get rid of
indirections, from Florian Westphal.
6) Skip unnecessary conntrack timeout updates in case the value is
still the same, also from Florian Westphal.
7) Remove unnecessary 'fall through' comments in empty switch cases,
from Li RongQing.
8) Fix lookup to fixed size hashtable sets on big endian with 32-bit keys.
9) Incorrect logic to deactivate path of fixed size hashtable sets,
element was being tested to self.
10) Remove nft_hash_key(), the bitmap set is always selected for 16-bit
keys.
11) Use boolean whenever possible in IPVS codebase, from Andrea Claudi.
12) Enter close state in conntrack if RST matches exact sequence number,
from Florian Westphal.
13) Initialize dst_cache in tunnel extension, from wenxu.
14) Pass protocol as u16 to xt_check_match and xt_check_target, from
Li RongQing.
15) SCTP header is granted to be in a linear area from IPVS NAT handler,
from Xin Long.
16) Don't steal packets coming from slave VRF device from the
ip_sabotage_in() path, from David Ahern.
17) Fix unsafe update of basechain stats, from Li RongQing.
18) Make sure CONNTRACK_LOCKS is power of 2 to let compiler optimize
modulo operation as bitwise AND, from Li RongQing.
19) Use device_attribute instead of internal definition in the IDLETIMER
target, from Sami Tolvanen.
20) Merge redir, masq and IPv4/IPv6 NAT chain types, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup to a173f066c7 ("netfilter: bridge: Don't sabotage nf_hook
calls from an l3mdev"). Some packets (e.g., ndisc) do not have the skb
device flipped to the l3mdev (e.g., VRF) device. Update ip_sabotage_in
to not drop packets for slave devices too. Currently, neighbor
solicitation packets for 'dev -> bridge (addr) -> vrf' setups are getting
dropped. This patch enables IPv6 communications for bridges with an
address that are enslaved to a VRF.
Fixes: 73e20b761a ("net: vrf: Add support for PREROUTING rules on vrf device")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The proto in struct xt_match and struct xt_target is u16, when
calling xt_check_target/match, their proto argument is u8,
and will cause truncation, it is harmless to ip packet, since
ip proto is u8
if a etable's match/target has proto that is u16, will cause
the check failure.
and convert be16 to short in bridge/netfilter/ebtables.c
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Drop switchdev_ops.switchdev_port_attr_set. Drop the uses of this field
from all clients, which were migrated to use switchdev notification in
the previous patches.
Add a new function switchdev_port_attr_notify() that sends the switchdev
notifications SWITCHDEV_PORT_ATTR_SET and calls the blocking (process)
notifier chain.
We have one odd case within net/bridge/br_switchdev.c with the
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attribute identifier that
requires executing from atomic context, we deal with that one
specifically.
Drop __switchdev_port_attr_set() and update switchdev_port_attr_set()
likewise.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are however frequently triggered by syzkaller, so remove them.
ebtables userspace should never trigger any of these, so there is little
value in making them pr_debug (or ratelimited).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 5a2de63fd1 ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e26 ("net:
bridge: remove ipv6 zero address check in mcast queries")
The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.
As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de>
Fixes: 5a2de63fd1 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Fixes: 0fe5119e26 ("net: bridge: remove ipv6 zero address check in mcast queries")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all switchdev drivers have been converted to check the
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS flags and report flags that they
do not support accordingly, we can migrate the bridge code to try to set
that attribute first, check the results and then do the actual setting.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_ip4_multicast_mrd_rcv only return 0 and -ENOMSG,
no other negative value
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for you net-next
tree:
1) Missing NFTA_RULE_POSITION_ID netlink attribute validation,
from Phil Sutter.
2) Restrict matching on tunnel metadata to rx/tx path, from wenxu.
3) Avoid indirect calls for IPV6=y, from Florian Westphal.
4) Add two indirections to prepare merger of IPV4 and IPV6 nat
modules, from Florian Westphal.
5) Broken indentation in ctnetlink, from Colin Ian King.
6) Patches to use struct_size() from netfilter and IPVS,
from Gustavo A. R. Silva.
7) Display kernel splat only once in case of racing to confirm
conntrack from bridge plus nfqueue setups, from Chieh-Min Wang.
8) Skip checksum validation for layer 4 protocols that don't need it,
patch from Alin Nastac.
9) Sparse warning due to symbol that should be static in CLUSTERIP,
from Wei Yongjun.
10) Add new toggle to disable SDP payload translation when media
endpoint is reachable though the same interface as the signalling
peer, from Alin Nastac.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some protocols have other means to verify the payload integrity
(AH, ESP, SCTP) while others are incompatible with nf_ip(6)_checksum
implementation because checksum is either optional or might be
partial (UDPLITE, DCCP, GRE). Because nf_ip(6)_checksum was used
to validate the packets, ip(6)tables REJECT rules were not capable
to generate ICMP(v6) errors for the protocols mentioned above.
This commit also fixes the incorrect pseudo-header protocol used
for IPv4 packets that carry other transport protocols than TCP or
UDP (pseudo-header used protocol 0 iso the proper value).
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a dedicated NDO for getting a port's parent ID, get rid
of SWITCHDEV_ATTR_ID_PORT_PARENT_ID and convert all callers to use the
NDO exclusively. This is a preliminary change to getting rid of
switchdev_ops eventually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for getting rid of switchdev_ops, create a dedicated NDO
operation for getting the port's parent identifier. There are
essentially two classes of drivers that need to implement getting the
port's parent ID which are VF/PF drivers with a built-in switch, and
pure switchdev drivers such as mlxsw, ocelot, dsa etc.
We introduce a helper function: dev_get_port_parent_id() which supports
recursion into the lower devices to obtain the first port's parent ID.
Convert the bridge, core and ipv4 multicast routing code to check for
such ndo_get_port_parent_id() and call the helper function when valid
before falling back to switchdev_port_attr_get(). This will allow us to
convert all relevant drivers in one go instead of having to implement
both switchdev_port_attr_get() and ndo_get_port_parent_id() operations,
then get rid of switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next tree:
1) Introduce a hashtable to speed up object lookups, from Florian Westphal.
2) Make direct calls to built-in extension, also from Florian.
3) Call helper before confirming the conntrack as it used to be originally,
from Florian.
4) Call request_module() to autoload br_netfilter when physdev is used
to relax the dependency, also from Florian.
5) Allow to insert rules at a given position ID that is internal to the
batch, from Phil Sutter.
6) Several patches to replace conntrack indirections by direct calls,
and to reduce modularization, from Florian. This also includes
several follow up patches to deal with minor fallout from this
rework.
7) Use RCU from conntrack gre helper, from Florian.
8) GRE conntrack module becomes built-in into nf_conntrack, from Florian.
9) Replace nf_ct_invert_tuplepr() by calls to nf_ct_invert_tuple(),
from Florian.
10) Unify sysctl handling at the core of nf_conntrack, from Florian.
11) Provide modparam to register conntrack hooks.
12) Allow to match on the interface kind string, from wenxu.
13) Remove several exported symbols, not required anymore now after
a bit of de-modulatization work has been done, from Florian.
14) Remove built-in map support in the hash extension, this can be
done with the existing userspace infrastructure, from laura.
15) Remove indirection to calculate checksums in IPVS, from Matteo Croce.
16) Use call wrappers for indirection in IPVS, also from Matteo.
17) Remove superfluous __percpu parameter in nft_counter, patch from
Luc Van Oostenryck.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) The nftnl mutex is now per-netns, therefore use reference counter
for matches and targets to deal with concurrent updates from netns.
Moreover, place extensions in a pernet list. Patches from Florian Westphal.
2) Bail out with EINVAL in case of negative timeouts via setsockopt()
through ip_vs_set_timeout(), from ZhangXiaoxu.
3) Spurious EINVAL on ebtables 32bit binary with 64bit kernel, also
from Florian.
4) Reset TCP option header parser in case of fingerprint mismatch,
otherwise follow up overlapping fingerprint definitions including
TCP options do not work, from Fernando Fernandez Mancera.
5) Compilation warning in ipt_CLUSTER with CONFIG_PROC_FS unset.
From Anders Roxell.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike ip(6)tables ebtables only counts user-defined chains.
The effect is that a 32bit ebtables binary on a 64bit kernel can do
'ebtables -N FOO' only after adding at least one rule, else the request
fails with -EINVAL.
This is a similar fix as done in
3f1e53abff ("netfilter: ebtables: don't attempt to allocate 0-sized compat array").
Fixes: 7d7d7e0211 ("netfilter: compat: reject huge allocation requests")
Reported-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When multiple multicast routers are present in a broadcast domain then
only one of them will be detectable via IGMP/MLD query snooping. The
multicast router with the lowest IP address will become the selected and
active querier while all other multicast routers will then refrain from
sending queries.
To detect such rather silent multicast routers, too, RFC4286
("Multicast Router Discovery") provides a standardized protocol to
detect multicast routers for multicast snooping switches.
This patch implements the necessary MRD Advertisement message parsing
and after successful processing adds such routers to the internal
multicast router list.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next to snooping IGMP/MLD queries RFC4541, section 2.1.1.a) recommends
to snoop multicast router advertisements to detect multicast routers.
Multicast router advertisements are sent to an "all-snoopers"
multicast address. To be able to receive them reliably, we need to
join this group.
Otherwise other snooping switches might refrain from forwarding these
advertisements to us.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors ip_mc_check_igmp(), ipv6_mc_check_mld() and
their callers (more precisely, the Linux bridge) to not rely on
the skb_trimmed parameter anymore.
An skb with its tail trimmed to the IP packet length was initially
introduced for the following three reasons:
1) To be able to verify the ICMPv6 checksum.
2) To be able to distinguish the version of an IGMP or MLD query.
They are distinguishable only by their size.
3) To avoid parsing data for an IGMPv3 or MLDv2 report that is
beyond the IP packet but still within the skb.
The first case still uses a cloned and potentially trimmed skb to
verfiy. However, there is no need to propagate it to the caller.
For the second and third case explicit IP packet length checks were
added.
This hopefully makes ip_mc_check_igmp() and ipv6_mc_check_mld() easier
to read and verfiy, as well as easier to use.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Externally learned entries can be added by a user or by a switch driver
that is notifying the bridge driver about entries that were learned in
hardware.
In the first case, the entries are not marked with the 'added_by_user'
flag, which causes switch drivers to ignore them and not offload them.
The 'added_by_user' flag can be set on externally learned FDB entries
based on the 'swdev_notify' parameter in br_fdb_external_learn_add(),
which effectively means if the created / updated FDB entry was added by
a user or not.
Fixes: 816a3bed95 ("switchdev: Add fdb.added_by_user to switchdev notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following command:
iptables -D FORWARD -m physdev ...
causes connectivity loss in some setups.
Reason is that iptables userspace will probe kernel for the module revision
of the physdev patch, and physdev has an artificial dependency on
br_netfilter (xt_physdev use makes no sense unless a br_netfilter module
is loaded).
This causes the "phydev" module to be loaded, which in turn enables the
"call-iptables" infrastructure.
bridged packets might then get dropped by the iptables ruleset.
The better fix would be to change the "call-iptables" defaults to 0 and
enforce explicit setting to 1, but that breaks backwards compatibility.
This does the next best thing: add a request_module call to checkentry.
This was a stray '-D ... -m physdev' won't activate br_netfilter
anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The skb header should be set to ethernet header before using
is_skb_forwardable. Because the ethernet header length has been
considered in is_skb_forwardable(including dev->hard_header_len
length).
To reproduce the issue:
1, add 2 ports on linux bridge br using following commands:
$ brctl addbr br
$ brctl addif br eth0
$ brctl addif br eth1
2, the MTU of eth0 and eth1 is 1500
3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4)
from eth0 to eth1
So the expect result is packet larger than 1500 cannot pass through
eth0 and eth1. But currently, the packet passes through success, it
means eth1's MTU limit doesn't take effect.
Fixes: f6367b4660 ("bridge: use is_skb_forwardable in forward path")
Cc: bridge@lists.linux-foundation.org
Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will enable vetoing of FDB entries. Make it possible
to communicate details of why an FDB entry is not acceptable back to the
user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.
In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This is the first batch of Netfilter fixes for your net tree:
1) Fix endless loop in nf_tables rules netlink dump, from Phil Sutter.
2) Reference counter leak in object from the error path, from Taehee Yoo.
3) Selective rule dump requires table and chain.
4) Fix DNAT with nft_flow_offload reverse route lookup, from wenxu.
5) Use GFP_KERNEL_ACCOUNT in vmalloc allocation from ebtables, from
Shakeel Butt.
6) Set ifindex from route to fix interaction with VRF slave device,
also from wenxu.
7) Use nfct_help() to check for conntrack helper, IPS_HELPER status
flag is only set from explicit helpers via -j CT, from Henry Yen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo reported forwarding issues inside the linux bridge,
if the enslaved interfaces use the fq qdisc.
Similar to commit 8203e2d844 ("net: clear skb->tstamp in
forwarding paths"), we need to clear the tstamp field in
the bridge forwarding path.
Fixes: 80b14dee2b ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Reported-and-tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The [ip,ip6,arp]_tables use x_tables_info internally and the underlying
memory is already accounted to kmemcg. Do the same for ebtables. The
syzbot, by using setsockopt(EBT_SO_SET_ENTRIES), was able to OOM the
whole system from a restricted memcg, a potential DoS.
By accounting the ebt_table_info, the memory used for ebt_table_info can
be contained within the memcg of the allocating process. However the
lifetime of ebt_table_info is independent of the allocating process and
is tied to the network namespace. So, the oom-killer will not be able to
relieve the memory pressure due to ebt_table_info memory. The memory for
ebt_table_info is allocated through vmalloc. Currently vmalloc does not
handle the oom-killed allocating process correctly and one large
allocation can bypass memcg limit enforcement. So, with this patch,
at least the small allocations will be contained. For large allocations,
we need to fix vmalloc.
Reported-by: syzbot+7713f3aa67be76b1552c@syzkaller.appspotmail.com
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When adding / deleting VLANs to / from a bridge port, the bridge driver
first tries to propagate the information via switchdev and falls back to
the 8021q driver in case the underlying driver does not support
switchdev. This can result in a memory leak [1] when VXLAN and mlxsw
ports are enslaved to the bridge:
$ ip link set dev vxlan0 master br0
# No mlxsw ports are enslaved to 'br0', so mlxsw ignores the switchdev
# notification and the bridge driver adds the VLAN on 'vxlan0' via the
# 8021q driver
$ bridge vlan add vid 10 dev vxlan0 pvid untagged
# mlxsw port is enslaved to the bridge
$ ip link set dev swp1 master br0
# mlxsw processes the switchdev notification and the 8021q driver is
# skipped
$ bridge vlan del vid 10 dev vxlan0
This results in 'struct vlan_info' and 'struct vlan_vid_info' being
leaked, as they were allocated by the 8021q driver during VLAN addition,
but never freed as the 8021q driver was skipped during deletion.
Fix this by introducing a new VLAN private flag that indicates whether
the VLAN was added on the port by switchdev or the 8021q driver. If the
VLAN was added by the 8021q driver, then we make sure to delete it via
the 8021q driver as well.
[1]
unreferenced object 0xffff88822d20b1e8 (size 256):
comm "bridge", pid 2532, jiffies 4295216998 (age 1188.830s)
hex dump (first 32 bytes):
e0 42 97 ce 81 88 ff ff 00 00 00 00 00 00 00 00 .B..............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330
[<00000000e0178b02>] vlan_vid_add+0x661/0x920
[<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00
[<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90
[<000000003535392c>] br_vlan_info+0x132/0x410
[<00000000aedaa9dc>] br_afspec+0x75c/0x870
[<00000000f5716133>] br_setlink+0x3dc/0x6d0
[<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30
[<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80
[<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0
[<000000008be8d614>] rtnetlink_rcv+0x21/0x30
[<000000009ab2ca25>] netlink_unicast+0x52f/0x740
[<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50
[<000000005d1e2050>] sock_sendmsg+0xbe/0x120
[<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0
[<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270
unreferenced object 0xffff888227454308 (size 32):
comm "bridge", pid 2532, jiffies 4295216998 (age 1188.882s)
hex dump (first 32 bytes):
88 b2 20 2d 82 88 ff ff 88 b2 20 2d 82 88 ff ff .. -...... -....
81 00 0a 00 01 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330
[<0000000018050631>] vlan_vid_add+0x3e6/0x920
[<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00
[<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90
[<000000003535392c>] br_vlan_info+0x132/0x410
[<00000000aedaa9dc>] br_afspec+0x75c/0x870
[<00000000f5716133>] br_setlink+0x3dc/0x6d0
[<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30
[<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80
[<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0
[<000000008be8d614>] rtnetlink_rcv+0x21/0x30
[<000000009ab2ca25>] netlink_unicast+0x52f/0x740
[<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50
[<000000005d1e2050>] sock_sendmsg+0xbe/0x120
[<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0
[<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270
Fixes: d70e42b22d ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling DNAT'ed packets on a bridge device, the neighbour cache entry
from lookup was used without checking its state. It means that a cache entry
in the NUD_STALE state will be used directly instead of entering the NUD_DELAY
state to confirm the reachability of the neighbor.
This problem becomes worse after commit 2724680bce ("neigh: Keep neighbour
cache entries if number of them is small enough."), since all neighbour cache
entries in the NUD_STALE state will be kept in the neighbour table as long as
the number of cache entries does not exceed the value specified in gc_thresh1.
This commit validates the state of a neighbour cache entry before using
the entry.
Signed-off-by: JianJhen Chen <kchen@synology.com>
Reviewed-by: JinLin Chen <jlchen@synology.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts the bridge netfilter (calling iptables hooks from bridge)
facility to use the extension infrastructure.
The bridge_nf specific hooks in skb clone and free paths are removed, they
have been replaced by the skb_ext hooks that do the same as the bridge nf
allocations hooks did.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pointer is going to be removed soon, so use the existing helpers in
more places to avoid noise when the removal happens.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
function br_multicast_toggle now always return 0,
so the variable 'err' is unneeded.
Also cleanup dead branch in br_changelink.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements ndo_fdb_get for the bridge
fdb.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port device seeks approval of a potential new MAC address, make
sure that should the bridge device end up using this address, all
interested parties would agree with it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is attached to a bridge, the address of the bridge in
question may change as well. Even if it would not change at this
point (because the current bridge address is lower), it might end up
changing later as a result of detach of another port, which can't be
vetoed.
Therefore issue NETDEV_PRE_CHANGEADDR regardless of whether the address
will be used at this point or not, and make sure all involved parties
would agree with the change.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, bridge driver has extack argument available to
pass to switchdev. Therefore extend switchdev_port_obj_add() with this
argument, updating all callers, and passing the argument through to
switchdev_port_obj_notify().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_bridge_setlink has been updated in the previous patch to have extack
available, and changelink RTNL op has had this argument since the time
extack was added. Propagate both through the bridge driver to eventually
reach br_switchdev_port_vlan_add(), where it will be used by subsequent
patches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may not be able to implement a VLAN addition or reconfiguration.
In those cases it's desirable to explain to the user that it was
rejected (and why).
To that end, add extack argument to ndo_bridge_setlink. Adapt all users
to that change.
Following patches will use the new argument in the bridge driver.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver unoffloads all FDB entries en bloc, it's inefficient to
send the switchdev notification one by one. Add a helper that unsets the
offload flag on FDB entries on a given bridge port and VLAN.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge's default hash_max was 512 which is rather conservative, now that
we're using the generic rhashtable API which autoshrinks let's increase
it to 4096 and move it to a define in br_private.h.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the bridge multicast uses the generic rhashtable interface we
can drop the hash_elasticity option as that is already done for us and
it's hardcoded to a maximum of RHT_ELASTICITY (16 currently). Add a
warning about the obsolete option when the hash_elasticity is set.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge multicast code has been using a mix of RCU and RCU-bh flavors
sometimes in questionable way. Since we've moved to rhashtable just use
non-bh RCU everywhere. In addition this simplifies freeing of objects
and allows us to remove some unnecessary callback functions.
v3: new patch
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge multicast code currently uses a custom resizable hashtable
which predates the generic rhashtable interface. It has many
shortcomings compared and duplicates functionality that is presently
available via the generic rhashtable, so this patch removes the custom
rhashtable implementation in favor of the kernel's generic rhashtable.
The hash maximum is kept and the rhashtable's size is used to do a loose
check if it's reached in which case we revert to the old behaviour and
disable further bridge multicast processing. Also now we can support any
hash maximum, doesn't need to be a power of 2.
v3: add non-rcu br_mdb_get variant and use it where multicast_lock is
held to avoid RCU splat, drop hash_max function and just set it
directly
v2: handle when IGMP snooping is undefined, add br_mdb_init/uninit
placeholders
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the function only works for the bridge device itself, but
subsequent patches will need to be able to query the PVID of a given
bridge port, so extend the function.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have at least one bool option, we can export all of the
supported bool options via optmask when dumping them.
v2: new patch
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new boolopt API to add an option which disables learning from
link-local packets. The default is kept as before and learning is
enabled. This is a simple map from a boolopt bit to a bridge private
flag that is tested before learning.
v2: pass NULL for extack via sysfs
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have been adding many new bridge options, a big number of which are
boolean but still take up netlink attribute ids and waste space in the skb.
Recently we discussed learning from link-local packets[1] and decided
yet another new boolean option will be needed, thus introducing this API
to save some bridge nl space.
The API supports changing the value of multiple boolean options at once
via the br_boolopt_multi struct which has an optmask (which options to
set, bit per opt) and optval (options' new values). Future boolean
options will only be added to the br_boolopt_id enum and then will have
to be handled in br_boolopt_toggle/get. The API will automatically
add the ability to change and export them via netlink, sysfs can use the
single boolopt function versions to do the same. The behaviour with
failing/succeeding is the same as with normal netlink option changing.
If an option requires mapping to internal kernel flag or needs special
configuration to be enabled then it should be handled in
br_boolopt_toggle. It should also be able to retrieve an option's current
state via br_boolopt_get.
v2: WARN_ON() on unsupported option as that shouldn't be possible and
also will help catch people who add new options without handling
them for both set and get. Pass down extack so if an option desires
it could set it on error and be more user-friendly.
[1] https://www.spinics.net/lists/netdev/msg532698.html
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change added a null check on p->dev after p->dev was being
dereferenced by the ns_capable check on p->dev. It turns out that
neither the p->dev and p->br null checks are necessary, and can be
removed, which cleans up a static analyis warning.
As Nikolay Aleksandrov noted, these checks can be removed because:
"My reasoning of why it shouldn't be possible:
- On port add new_nbp() sets both p->dev and p->br before creating
kobj/sysfs
- On port del (trickier) del_nbp() calls kobject_del() before call_rcu()
to destroy the port which in turn calls sysfs_remove_dir() which uses
kernfs_remove() which deactivates (shouldn't be able to open new
files) and calls kernfs_drain() to drain current open/mmaped files in
the respective dir before continuing, thus making it impossible to
open a bridge port sysfs file with p->dev and p->br equal to NULL.
So I think it's safe to remove those checks altogether. It'd be nice to
get a second look over my reasoning as I might be missing something in
sysfs/kernfs call path."
Thanks to Nikolay Aleksandrov's suggestion to remove the check and
David Miller for sanity checking this.
Detected by CoverityScan, CID#751490 ("Dereference before null check")
Fixes: a5f3ea54f3 ("net: bridge: add support for raw sysfs port options")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow querying bridge port flags so that drivers capable of performing
VxLAN learning will update the bridge driver only if learning is enabled
on its bridge port corresponding to the VxLAN device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported a use-after-free of the global vlan context on port vlan
destruction. When I added per-port vlan stats I missed the fact that the
global vlan context can be freed before the per-port vlan rcu callback.
There're a few different ways to deal with this, I've chosen to add a
new private flag that is set only when per-port stats are allocated so
we can directly check it on destruction without dereferencing the global
context at all. The new field in net_bridge_vlan uses a hole.
v2: cosmetic change, move the check to br_process_vlan_info where the
other checks are done
v3: add change log in the patch, add private (in-kernel only) flags in a
hole in net_bridge_vlan struct and use that instead of mixing
user-space flags with private flags
Fixes: 9163a0fc1f ("net: bridge: add support for per-port vlan stats")
Reported-by: syzbot+04681da557a0e49a52e5@syzkaller.appspotmail.com
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes assumption than vlan_tci != 0 when tag is present.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently a check was added which prevents marking of routers with zero
source address, but for IPv6 that cannot happen as the relevant RFCs
actually forbid such packets:
RFC 2710 (MLDv1):
"To be valid, the Query message MUST
come from a link-local IPv6 Source Address, be at least 24 octets
long, and have a correct MLD checksum."
Same goes for RFC 3810.
And also it can be seen as a requirement in ipv6_mc_check_mld_query()
which is used by the bridge to validate the message before processing
it. Thus any queries with :: source address won't be processed anyway.
So just remove the check for zero IPv6 source address from the query
processing function.
Fixes: 5a2de63fd1 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on RFC 4541, 2.1.1. IGMP Forwarding Rules
The switch supporting IGMP snooping must maintain a list of
multicast routers and the ports on which they are attached. This
list can be constructed in any combination of the following ways:
a) This list should be built by the snooping switch sending
Multicast Router Solicitation messages as described in IGMP
Multicast Router Discovery [MRDISC]. It may also snoop
Multicast Router Advertisement messages sent by and to other
nodes.
b) The arrival port for IGMP Queries (sent by multicast routers)
where the source address is not 0.0.0.0.
We should not add the port to router list when receives query with source
0.0.0.0.
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
readability improvements for the formatted output, some LICENSES updates
including the addition of the ISC license, the removal of the unloved and
unmaintained 00-INDEX files, the deprecated APIs document from Kees, more
MM docs from Mike Rapoport, and the usual pile of typo fixes and
corrections.
-----BEGIN PGP SIGNATURE-----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=C0wt
-----END PGP SIGNATURE-----
Merge tag 'docs-4.20' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"This is a fairly typical cycle for documentation. There's some welcome
readability improvements for the formatted output, some LICENSES
updates including the addition of the ISC license, the removal of the
unloved and unmaintained 00-INDEX files, the deprecated APIs document
from Kees, more MM docs from Mike Rapoport, and the usual pile of typo
fixes and corrections"
* tag 'docs-4.20' of git://git.lwn.net/linux: (41 commits)
docs: Fix typos in histogram.rst
docs: Introduce deprecated APIs list
kernel-doc: fix declaration type determination
doc: fix a typo in adding-syscalls.rst
docs/admin-guide: memory-hotplug: remove table of contents
doc: printk-formats: Remove bogus kobject references for device nodes
Documentation: preempt-locking: Use better example
dm flakey: Document "error_writes" feature
docs/completion.txt: Fix a couple of punctuation nits
LICENSES: Add ISC license text
LICENSES: Add note to CDDL-1.0 license that it should not be used
docs/core-api: memory-hotplug: add some details about locking internals
docs/core-api: rename memory-hotplug-notifier to memory-hotplug
docs: improve readability for people with poorer eyesight
yama: clarify ptrace_scope=2 in Yama documentation
docs/vm: split memory hotplug notifier description to Documentation/core-api
docs: move memory hotplug description into admin-guide/mm
doc: Fix acronym "FEKEK" in ecryptfs
docs: fix some broken documentation references
iommu: Fix passthrough option documentation
...
This fixes a problem introduced by:
commit 2cde6acd49 ("netpoll: Fix __netpoll_rcu_free so that it can hold the rtnl lock")
When using netconsole on a bond, __netpoll_cleanup can asynchronously
recurse multiple times, each __netpoll_free_async call can result in
more __netpoll_free_async's. This means there is now a race between
cleanup_work queues on multiple netpoll_info's on multiple devices and
the configuration of a new netpoll. For example if a netconsole is set
to enable 0, reconfigured, and enable 1 immediately, this netconsole
will likely not work.
Given the reason for __netpoll_free_async is it can be called when rtnl
is not locked, if it is locked, we should be able to execute
synchronously. It appears to be locked everywhere it's called from.
Generalize the design pattern from the teaming driver for current
callers of __netpoll_free_async.
CC: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, an FDB entry only ceases being offloaded when it is deleted.
This changes with VxLAN encapsulation.
Devices capable of performing VxLAN encapsulation usually have only one
FDB table, unlike the software data path which has two - one in the
bridge driver and another in the VxLAN driver.
Therefore, bridge FDB entries pointing to a VxLAN device are only
offloaded if there is a corresponding entry in the VxLAN FDB.
Allow clearing the offload indication in case the corresponding entry
was deleted from the VxLAN FDB.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After per-port vlan stats, vlan stats should be released
when fail to add vlan
Fixes: 9163a0fc1f ("net: bridge: add support for per-port vlan stats")
CC: bridge@lists.linux-foundation.org
cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an option to have per-port vlan stats instead of the
default global stats. The option can be set only when there are no port
vlans in the bridge since we need to allocate the stats if it is set
when vlans are being added to ports (and respectively free them
when being deleted). Also bump RTNL_MAX_TYPE as the bridge is the
largest user of options. The current stats design allows us to add
these without any changes to the fast-path, it all comes down to
the per-vlan stats pointer which, if this option is enabled, will
be allocated for each port vlan instead of using the global bridge-wide
one.
CC: bridge@lists.linux-foundation.org
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update br_mdb_dump for strict data checking. If the flag is set,
the dump request is expected to have a br_port_msg struct as the
header. All elements of the struct are expected to be 0 and no
attributes can be appended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 13cefad2f2 ("net: bridge: convert and rename mcast disabled")
converted the 'multicast_disabled' field to an option bit named
'BROPT_MULTICAST_ENABLED'.
While the old field was implicitly initialized to 0, the new field is
not initialized, resulting in the bridge defaulting to multicast
disabled state and breaking existing applications.
Fix this by explicitly initializing the option.
Fixes: 13cefad2f2 ("net: bridge: convert and rename mcast disabled")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to explicitly zero is_sticky when creating a new fdb, otherwise
we might get a stale value for a new entry.
Fixes: 435f2e7cc0 ("net: bridge: add support for sticky fdb entries")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Further reduce the size of net_bridge with 8 bytes and reduce the number of
holes in it:
Before: holes: 5, sum holes: 15
After: holes: 3, sum holes: 7
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the last remaining bool option to a bit thus reducing the overall
net_bridge size further by 8 bytes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the neigh_suppress_enabled option to a bit.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the rest of the mcast options to bits. It also packs
the mcast options a little better by moving multicast_mld_version to an
existing hole, reducing the net_bridge size by 8 bytes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert mcast disabled to an option bit and while doing so convert the
logic to check if multicast is enabled instead. That is make the logic
follow the option value - if it's set then mcast is enabled and vice versa.
This avoids a few confusing places where we inverted the value that's being
set to follow the mcast_disabled logic.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert group_addr_set internal bridge opt to a bit.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No functional change, convert of nf_call_[ip|ip6|arp]tables to bits.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge options have usually been added as separate fields all over the
net_bridge struct taking up space and ending up in different cache lines.
Let's move them to a single bitfield to save up space and speedup lookups.
This patch adds a simple API for option modifying and retrieving using
bitops and converts the first user of the API - the bridge vlan options
(vlan_enabled and vlan_stats_enabled).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have a mix of opening brackets on new lines and on the same
line, let's move them all on the same line.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: ed842faeb2 ("bridge: suppress nd pkts on BR_NEIGH_SUPPRESS ports")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some documentation files received recent changes and are
pointing to wrong places.
Those references can easily fixed with the help of a
script:
$ ./scripts/documentation-file-ref-check --fix
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
For starters, the bridge netfilter code registers operations that
are invoked any time nh_hook is called. Specifically, ip_sabotage_in
watches for nested calls for NF_INET_PRE_ROUTING when a bridge is in
the stack.
Packet wise, the bridge netfilter hook runs first. br_nf_pre_routing
allocates nf_bridge, sets in_prerouting to 1 and calls NF_HOOK for
NF_INET_PRE_ROUTING. It's finish function, br_nf_pre_routing_finish,
then resets in_prerouting flag to 0 and the packet continues up the
stack. The packet eventually makes it to the VRF driver and it invokes
nf_hook for NF_INET_PRE_ROUTING in case any rules have been added against
the vrf device.
Because of the registered operations the call to nf_hook causes
ip_sabotage_in to be invoked. That function sees the nf_bridge on the
skb and that in_prerouting is not set. Thinking it is an invalid nested
call it steals (drops) the packet.
Update ip_sabotage_in to recognize that the bridge or one of its upper
devices (e.g., vlan) can be enslaved to a VRF (L3 master device) and
allow the packet to go through the nf_hook a second time.
Fixes: 73e20b761a ("net: vrf: Add support for PREROUTING rules on vrf device")
Reported-by: D'Souza, Nelson <ndsouza@ciena.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add support for entries which are "sticky", i.e. will not change their port
if they show up from a different one. A new ndm flag is introduced for that
purpose - NTF_STICKY. We allow to set it only to non-local entries.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The err is not modified after initalization, So remove it and make
it to be void function.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netfilter exposes standard hook priorities in case of ipv4, ipv6 and
arp but not in case of bridge.
This patch exposes the hook priority values of the bridge family (which are
different from the formerly mentioned) via uapi so that they can be used by
user-space applications just like the others.
Signed-off-by: Máté Eckl <ecklm94@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a new port attribute - IFLA_BRPORT_BACKUP_PORT, which
allows to set a backup port to be used for known unicast traffic if the
port has gone carrier down. The backup pointer is rcu protected and set
only under RTNL, a counter is maintained so when deleting a port we know
how many other ports reference it as a backup and we remove it from all.
Also the pointer is in the first cache line which is hot at the time of
the check and thus in the common case we only add one more test.
The backup port will be used only for the non-flooding case since
it's a part of the bridge and the flooded packets will be forwarded to it
anyway. To remove the forwarding just send a 0/non-existing backup port.
This is used to avoid numerous scalability problems when using MLAG most
notably if we have thousands of fdbs one would need to change all of them
on port carrier going down which takes too long and causes a storm of fdb
notifications (and again when the port comes back up). In a Multi-chassis
Link Aggregation setup usually hosts are connected to two different
switches which act as a single logical switch. Those switches usually have
a control and backup link between them called peerlink which might be used
for communication in case a host loses connectivity to one of them.
We need a fast way to failover in case a host port goes down and currently
none of the solutions (like bond) cannot fulfill the requirements because
the participating ports are actually the "master" devices and must have the
same peerlink as their backup interface and at the same time all of them
must participate in the bridge device. As Roopa noted it's normal practice
in routing called fast re-route where a precalculated backup path is used
when the main one is down.
Another use case of this is with EVPN, having a single vxlan device which
is backup of every port. Due to the nature of master devices it's not
currently possible to use one device as a backup for many and still have
all of them participate in the bridge (which is master itself).
More detailed information about MLAG is available at the link below.
https://docs.cumulusnetworks.com/display/DOCS/Multi-Chassis+Link+Aggregation+-+MLAG
Further explanation and a diagram by Roopa:
Two switches acting in a MLAG pair are connected by the peerlink
interface which is a bridge port.
the config on one of the switches looks like the below. The other
switch also has a similar config.
eth0 is connected to one port on the server. And the server is
connected to both switches.
br0 -- team0---eth0
|
-- switch-peerlink
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new alternative store callback for port sysfs options
which takes a raw value (buf) and can use it directly. It is needed for the
backup port sysfs support since we have to pass the device by its name.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating various bridge objects in /sys/class/net/... make sure
that they belong to the container's owner instead of global root (if
they belong to a container/namespace).
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the nft_reject_br_send_v4_tcp_reset(), a ttl is set by the
nf_reject_iphdr_put(). so, below code is unnecessary.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) Reject non-null terminated helper names from xt_CT, from Gao Feng.
2) Fix KASAN splat due to out-of-bound access from commit phase, from
Alexey Kodanev.
3) Missing conntrack hook registration on IPVS FTP helper, from Julian
Anastasov.
4) Incorrect skbuff allocation size in bridge nft_reject, from Taehee Yoo.
5) Fix inverted check on packet xmit to non-local addresses, also from
Julian.
6) Fix ebtables alignment compat problems, from Alin Nastac.
7) Hook mask checks are not correct in xt_set, from Serhey Popovych.
8) Fix timeout listing of element in ipsets, from Jozsef.
9) Cap maximum timeout value in ipset, also from Jozsef.
10) Don't allow family option for hash:mac sets, from Florent Fourcot.
11) Restrict ebtables to work with NFPROTO_BRIDGE targets only, this
Florian.
12) Another bug reported by KASAN in the rbtree set backend, from
Taehee Yoo.
13) Missing __IPS_MAX_BIT update doesn't include IPS_OFFLOAD_BIT.
From Gao Feng.
14) Missing initialization of match/target in ebtables, from Florian
Westphal.
15) Remove useless nft_dup.h file in include path, from C. Labbe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of br_fdb_find() need to hold the hash lock, which
br_fdb_find_port() doesn't do. However, since br_fdb_find_port() is not
doing any actual FDB manipulation, the hash lock is not really needed at
all. So convert to br_fdb_find_rcu(), surrounded by rcu_read_lock() /
_unlock() pair.
The device pointer copied from inside the FDB entry is then kept alive
by the RTNL lock, which br_fdb_find_port() asserts.
Fixes: 4d4fd36126 ("net: bridge: Publish bridge accessor functions")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reports following splat:
BUG: KMSAN: uninit-value in ebt_stp_mt_check+0x24b/0x450
net/bridge/netfilter/ebt_stp.c:162
ebt_stp_mt_check+0x24b/0x450 net/bridge/netfilter/ebt_stp.c:162
xt_check_match+0x1438/0x1650 net/netfilter/x_tables.c:506
ebt_check_match net/bridge/netfilter/ebtables.c:372 [inline]
ebt_check_entry net/bridge/netfilter/ebtables.c:702 [inline]
The uninitialised access is
xt_mtchk_param->nft_compat
... which should be set to 0.
Fix it by zeroing the struct beforehand, same for tgchk.
ip(6)tables targetinfo uses c99-style initialiser, so no change
needed there.
Reported-by: syzbot+da4494182233c23a5fcf@syzkaller.appspotmail.com
Fixes: 55917a21d0 ("netfilter: x_tables: add context to know if extension runs from nft_compat")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
-----BEGIN PGP SIGNATURE-----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=10u6
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20180605' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"Another reasonable chunk of audit changes for v4.18, thirteen patches
in total.
The thirteen patches can mostly be broken down into one of four
categories: general bug fixes, accessor functions for audit state
stored in the task_struct, negative filter matches on executable
names, and extending the (relatively) new seccomp logging knobs to the
audit subsystem.
The main driver for the accessor functions from Richard are the
changes we're working on to associate audit events with containers,
but I think they have some standalone value too so I figured it would
be good to get them in now.
The seccomp/audit patches from Tyler apply the seccomp logging
improvements from a few releases ago to audit's seccomp logging;
starting with this patchset the changes in
/proc/sys/kernel/seccomp/actions_logged should apply to both the
standard kernel logging and audit.
As usual, everything passes the audit-testsuite and it happens to
merge cleanly with your tree"
[ Heh, except it had trivial merge conflicts with the SELinux tree that
also came in from Paul - Linus ]
* tag 'audit-pr-20180605' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: Fix wrong task in comparison of session ID
audit: use existing session info function
audit: normalize loginuid read access
audit: use new audit_context access funciton for seccomp_actions_logged
audit: use inline function to set audit context
audit: use inline function to get audit context
audit: convert sessionid unset to a macro
seccomp: Don't special case audited processes when logging
seccomp: Audit attempts to modify the actions_logged sysctl
seccomp: Configurable separator for the actions_logged string
seccomp: Separate read and write code for actions_logged sysctl
audit: allow not equal op for audit by executable
audit: add syscall information to FEATURE_CHANGE records
the ebtables evaluation loop expects targets to return
positive values (jumps), or negative values (absolute verdicts).
This is completely different from what xtables does.
In xtables, targets are expected to return the standard netfilter
verdicts, i.e. NF_DROP, NF_ACCEPT, etc.
ebtables will consider these as jumps.
Therefore reject any target found due to unspec fallback.
v2: also reject watchers. ebtables ignores their return value, so
a target that assumes skb ownership (and returns NF_STOLEN) causes
use-after-free.
The only watchers in the 'ebtables' front-end are log and nflog;
both have AF_BRIDGE specific wrappers on kernel side.
Reported-by: syzbot+2b43f681169a2a0d306a@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On arm64, ebt_entry_{match,watcher,target} structs are 40 bytes long
while on 32-bit arm these structs have a size of 36 bytes.
COMPAT_XT_ALIGN() macro cannot be used here to determine the necessary
padding for the CONFIG_COMPAT because it imposes an 8-byte boundary
alignment, condition that is not found in 32-bit ebtables application.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In order to allocate icmpv6 skb, sizeof(struct ipv6hdr) should be used.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver might need to react to changes in settings of brentry VLANs.
Therefore send switchdev port notifications for these as well. Reuse
SWITCHDEV_OBJ_ID_PORT_VLAN for this purpose. Listeners should use
netif_is_bridge_master() on orig_dev to determine whether the
notification is about a bridge port or a bridge.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the code that deals with adding a preexisting VLAN to bridge CPU
port to a separate function. A follow-up patch introduces a need to roll
back operations in this block due to an error, and this split will make
the error-handling code clearer.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A call to switchdev_port_obj_add() or switchdev_port_obj_del() involves
initializing a struct switchdev_obj_port_vlan, a piece of code that
repeats on each call site almost verbatim. While in the current codebase
there is just one duplicated add call, the follow-up patches add more of
both add and del calls.
Thus to remove the duplication, extract the repetition into named
functions and reuse.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a new port flag - BR_ISOLATED. If it is set
then isolated ports cannot communicate between each other, but they can
still communicate with non-isolated ports. The same can be achieved via
ACLs but they can't scale with large number of ports and also the
complexity of the rules grows. This feature can be used to achieve
isolated vlan functionality (similar to pvlan) as well, though currently
it will be port-wide (for all vlans on the port). The new test in
should_deliver uses data that is already cache hot and the new boolean
is used to avoid an additional source port test in should_deliver.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
Recognizing that the audit context is an internal audit value, use an
access function to retrieve the audit context pointer for the task
rather than reaching directly into the task struct to get it.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: merge fuzz in auditsc.c and selinuxfs.c, checkpatch.pl fixes]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Fix handling of simultaneous open TCP connection in conntrack,
from Jozsef Kadlecsik.
2) Insufficient sanitify check of xtables extension names, from
Florian Westphal.
3) Skip unnecessary synchronize_rcu() call when transaction log
is already empty, from Florian Westphal.
4) Incorrect destination mac validation in ebt_stp, from Stephen
Hemminger.
5) xtables module reference counter leak in nft_compat, from
Florian Westphal.
6) Incorrect connection reference counting logic in IPVS
one-packet scheduler, from Julian Anastasov.
7) Wrong stats for 32-bits CPU in IPVS, also from Julian.
8) Calm down sparse error in netfilter core, also from Florian.
9) Use nla_strlcpy to fix compilation warning in nfnetlink_acct
and nfnetlink_cthelper, again from Florian.
10) Missing module alias in icmp and icmp6 xtables extensions,
from Florian Westphal.
11) Base chain statistics in nf_tables may be unset/null, from Florian.
12) Fix handling of large matchinfo size in nft_compat, this includes
one preparation for before this fix. From Florian.
13) Fix bogus EBUSY error when deleting chains due to incorrect reference
counting from the preparation phase of the two-phase commit protocol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mirroring offload in mlxsw needs to check that a given VLAN is allowed
to ingress the bridge device. br_vlan_get_info() is the function that is
used for this, however currently it only supports bridge port devices.
Extend it to support bridge masters as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The destination mac (destmac) is only valid if EBT_DESTMAC flag
is set. Fix by changing the order of the comparison to look for
the flag first.
Reported-by: syzbot+5c06e318fc558cc27823@syzkaller.appspotmail.com
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree, more relevant updates in this batch are:
1) Add Maglev support to IPVS. Moreover, store lastest server weight in
IPVS since this is needed by maglev, patches from from Inju Song.
2) Preparation works to add iptables flowtable support, patches
from Felix Fietkau.
3) Hand over flows back to conntrack slow path in case of TCP RST/FIN
packet is seen via new teardown state, also from Felix.
4) Add support for extended netlink error reporting for nf_tables.
5) Support for larger timeouts that 23 days in nf_tables, patch from
Florian Westphal.
6) Always set an upper limit to dynamic sets, also from Florian.
7) Allow number generator to make map lookups, from Laura Garcia.
8) Use hash_32() instead of opencode hashing in IPVS, from Vicent Bernat.
9) Extend ip6tables SRH match to support previous, next and last SID,
from Ahmed Abdelsalam.
10) Move Passive OS fingerprint nf_osf.c, from Fernando Fernandez.
11) Expose nf_conntrack_max through ctnetlink, from Florent Fourcot.
12) Several housekeeping patches for xt_NFLOG, x_tables and ebtables,
from Taehee Yoo.
13) Unify meta bridge with core nft_meta, then make nft_meta built-in.
Make rt and exthdr built-in too, again from Florian.
14) Missing initialization of tbl->entries in IPVS, from Cong Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not automatically bail out on sending notifications about activity on
non-user-added FDB entries. Instead, notify about this activity except
for cases where the activity itself originates in a notification, to
avoid sending duplicate notifications.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch enables sending notifications also for events on FDB
entries that weren't added by the user. Give the drivers the information
necessary to distinguish between the two origins of FDB entries.
To maintain the current behavior, have switchdev-implementing drivers
bail out on notifications about non-user-added FDB entries. In case of
mlxsw driver, allow a call to mlxsw_sp_span_respin() so that SPAN over
bridge catches up with the changed FDB.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While handling netdevice events, br_device_event() sometimes uses
br_stp_(disable|enable)_port which unconditionally send a notification,
but then a second notification for the same event is sent at the end of
the br_device_event() function. To avoid sending duplicate notifications
in such cases, check if one has already been sent (i.e.
br_stp_enable/disable_port have been called).
The patch is based on a change by Satish Ashok.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple new functions to allow querying FDB and vlan settings of a
bridge.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we set a bond slave's master to bridge via ioctl, we only check
the IFF_BRIDGE_PORT flag. Although we will find the slave's real master
at netdev_master_upper_dev_link() later, it already does some settings
and allocates some resources. It would be better to return as early
as possible.
v1 -> v2:
use netdev_master_upper_dev_get() instead of netdev_has_any_upper_dev()
to check if we have a master, because not all upper devs are masters,
e.g. vlan device.
Reported-by: syzbot+de73361ee4971b6e6f75@syzkaller.appspotmail.com
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use hlist_entry_safe() instead of open-coding it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It overcomplicates things for no reason.
nft_meta_bridge only offers retrieval of bridge port interface name.
Because of this being its own module, we had to export all nft_meta
functions, which we can then make static again (which even reduces
the size of nft_meta -- including bridge port retrieval...):
before:
text data bss dec hex filename
1838 832 0 2670 a6e net/bridge/netfilter/nft_meta_bridge.ko
6147 936 1 7084 1bac net/netfilter/nft_meta.ko
after:
5826 936 1 6763 1a6b net/netfilter/nft_meta.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ebt_get_target similar to {ip/ip6/arp}t_get_target.
and ebt_get_target_c similar to {ip/ip6/arp}t_get_target_c.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
EBT_MATCH and EBT_NOMATCH are used to change return value.
match functions(ebt_xxx.c) return false when received frame is not matched
and returns true when received frame is matched.
but, EBT_MATCH_ITERATE understands oppositely.
so, to change return value, EBT_MATCH and EBT_NOMATCH are used.
but, we can use operation '!' simply.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A ebt_free_table_info frees all of chainstacks.
It similar to xt_free_table_info. this inline function
reduces code line.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Dmitry reports 32bit ebtables on 64bit kernel got broken by
a recent change that returns -EINVAL when ruleset has no entries.
ebtables however only counts user-defined chains, so for the
initial table nentries will be 0.
Don't try to allocate the compat array in this case, as no user
defined rules exist no rule will need 64bit translation.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: 7d7d7e0211 ("netfilter: compat: reject huge allocation requests")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
As Roopa noted today the biggest source of problems when configuring
bridge and ports is that the bridge MTU keeps changing automatically on
port events (add/del/changemtu). That leads to inconsistent behaviour
and network config software needs to chase the MTU and fix it on each
such event. Let's improve on that situation and allow for the user to
set any MTU within ETH_MIN/MAX limits, but once manually configured it
is the user's responsibility to keep it correct afterwards.
In case the MTU isn't manually set - the behaviour reverts to the
previous and the bridge follows the minimum MTU.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the bridge was changed to automatically set maximum MTU on port
events (add/del/changemtu) when vlan filtering is enabled, but that
actually changes behaviour in a way which breaks some setups and can lead
to packet drops. In order to still allow that maximum to be set while being
compatible, we add the ability for the user to tune the bridge MTU up to
the maximum when vlan filtering is enabled, but that has to be done
explicitly and all port events (add/del/changemtu) lead to resetting that
MTU to the minimum as before.
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree. This batch comes with more input sanitization for xtables to
address bug reports from fuzzers, preparation works to the flowtable
infrastructure and assorted updates. In no particular order, they are:
1) Make sure userspace provides a valid standard target verdict, from
Florian Westphal.
2) Sanitize error target size, also from Florian.
3) Validate that last rule in basechain matches underflow/policy since
userspace assumes this when decoding the ruleset blob that comes
from the kernel, from Florian.
4) Consolidate hook entry checks through xt_check_table_hooks(),
patch from Florian.
5) Cap ruleset allocations at 512 mbytes, 134217728 rules and reject
very large compat offset arrays, so we have a reasonable upper limit
and fuzzers don't exercise the oom-killer. Patches from Florian.
6) Several WARN_ON checks on xtables mutex helper, from Florian.
7) xt_rateest now has a hashtable per net, from Cong Wang.
8) Consolidate counter allocation in xt_counters_alloc(), from Florian.
9) Earlier xt_table_unlock() call in {ip,ip6,arp,eb}tables, patch
from Xin Long.
10) Set FLOW_OFFLOAD_DIR_* to IP_CT_DIR_* definitions, patch from
Felix Fietkau.
11) Consolidate code through flow_offload_fill_dir(), also from Felix.
12) Inline ip6_dst_mtu_forward() just like ip_dst_mtu_maybe_forward()
to remove a dependency with flowtable and ipv6.ko, from Felix.
13) Cache mtu size in flow_offload_tuple object, this is safe for
forwarding as f87c10a8aa describes, from Felix.
14) Rename nf_flow_table.c to nf_flow_table_core.o, to simplify too
modular infrastructure, from Felix.
15) Add rt0, rt2 and rt4 IPv6 routing extension support, patch from
Ahmed Abdelsalam.
16) Remove unused parameter in nf_conncount_count(), from Yi-Hung Wei.
17) Support for counting only to nf_conncount infrastructure, patch
from Yi-Hung Wei.
18) Add strict NFT_CT_{SRC_IP,DST_IP,SRC_IP6,DST_IP6} key datatypes
to nft_ct.
19) Use boolean as return value from ipt_ah and from IPVS too, patch
from Gustavo A. R. Silva.
20) Remove useless parameters in nfnl_acct_overquota() and
nf_conntrack_broadcast_help(), from Taehee Yoo.
21) Use ipv6_addr_is_multicast() from xt_cluster, also from Taehee Yoo.
22) Statify nf_tables_obj_lookup_byhandle, patch from Fengguang Wu.
23) Fix typo in xt_limit, from Geert Uytterhoeven.
24) Do no use VLAs in Netfilter code, again from Gustavo.
25) Use ADD_COUNTER from ebtables, from Taehee Yoo.
26) Bitshift support for CONNMARK and MARK targets, from Jack Ma.
27) Use pr_*() and add pr_fmt(), from Arushi Singhal.
28) Add synproxy support to ctnetlink.
29) ICMP type and IGMP matching support for ebtables, patches from
Matthias Schiffer.
30) Support for the revision infrastructure to ebtables, from
Bernie Harris.
31) String match support for ebtables, also from Bernie.
32) Documentation for the new flowtable infrastructure.
33) Use generic comparison functions in ebt_stp, from Joe Perches.
34) Demodularize filter chains in nftables.
35) Register conntrack hooks in case nftables NAT chain is added.
36) Merge assignments with return in a couple of spots in the
Netfilter codebase, also from Arushi.
37) Document that xtables percpu counters are stored in the same
memory area, from Ben Hutchings.
38) Revert mark_source_chains() sanity checks that break existing
rulesets, from Florian Westphal.
39) Use is_zero_ether_addr() in the ipset codebase, from Joe Perches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
One module per supported filter chain family type takes too much memory
for very little code - too much modularization - place all chain filter
definitions in one single file.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use WARN_ON() instead since it should not happen that neither family
goes over NFPROTO_NUMPROTO nor there is already a chain of this type
already registered.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use nft_ prefix. By when I added chain types, I forgot to use the
nftables prefix. Rename enum nft_chain_type to enum nft_chain_types too,
otherwise there is an overlap.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of unnecessary const declarations, use the generic functions to
save a little object space.
$ size net/bridge/netfilter/ebt_stp.o*
text data bss dec hex filename
1250 144 0 1394 572 net/bridge/netfilter/ebt_stp.o.new
1344 144 0 1488 5d0 net/bridge/netfilter/ebt_stp.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently ebtables assumes that the revision number of all match
modules is 0, which is an issue when trying to use existing
xtables matches with ebtables. The solution is to modify ebtables
to allow extensions to specify a revision number, similar to
iptables. This gets passed down to the kernel, which is then able
to find the match module correctly.
To main binary backwards compatibility, the size of the ebt_entry
structures is not changed, only the size of the name field is
decreased by 1 byte to make room for the revision field.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Synchronous pernet_operations are not allowed anymore.
All are asynchronous. So, drop the structure member.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to use br_vlan_enabled() helper otherwise we'll break builds
without bridge vlans:
net/bridge//br_if.c: In function ‘br_mtu’:
net/bridge//br_if.c:458:8: error: ‘const struct net_bridge’ has no
member named ‘vlan_enabled’
if (br->vlan_enabled)
^
net/bridge//br_if.c:462:1: warning: control reaches end of non-void
function [-Wreturn-type]
}
^
scripts/Makefile.build:324: recipe for target 'net/bridge//br_if.o'
failed
Fixes: 419d14af9e ("bridge: Allow max MTU when multiple VLANs present")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the bridge is allowing multiple VLANs, some VLANs may have
different MTUs. Instead of choosing the minimum MTU for the
bridge interface, choose the maximum MTU of the bridge members.
With this the user only needs to set a larger MTU on the member
ports that are participating in the large MTU VLANS.
Signed-off-by: Chas Williams <3chas3@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have ICMPv6 type/code matches (which can be used to distinguish
different types of MLD packets). Add support for IPv4 IGMP matches in the
same way.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We already have ICMPv6 type/code matches. This adds support for IPv4 ICMP
matches in the same way.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
xtables uses ADD_COUNTER macro to increase
packet and byte count. ebtables also can use this.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ebt_among is special, it has a dynamic match size and is exempt
from the central size checks.
commit c4585a2823 ("bridge: ebt_among: add missing match size checks")
added validation for pool size, but missed fact that the macros
ebt_among_wh_src/dst can already return out-of-bound result because
they do not check value of wh_src/dst_ofs (an offset) vs. the size
of the match that userspace gave to us.
v2:
check that offset has correct alignment.
Paolo Abeni points out that we should also check that src/dst
wormhash arrays do not overlap, and src + length lines up with
start of dst (or vice versa).
v3: compact wormhash_sizes_valid() part
NB: Fixes tag is intentionally wrong, this bug exists from day
one when match was added for 2.6 kernel. Tag is there so stable
maintainers will notice this one too.
Tested with same rules from the earlier patch.
Fixes: c4585a2823 ("bridge: ebt_among: add missing match size checks")
Reported-by: <syzbot+bdabab6f1983a03fc009@syzkaller.appspotmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The last rule in the blob has next_entry offset that is same as total size.
This made "ebtables32 -A OUTPUT -d de:ad:be:ef:01:02" fail on 64 bit kernel.
Fixes: b718121685 ("netfilter: ebtables: CONFIG_COMPAT: don't trust userland offsets")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
should have no impact, function still always returns 0.
This patch is only to ease review.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
These pernet_operations use nf_log_set() and nf_log_unset()
in their methods:
nf_log_bridge_net_ops
nf_log_arp_net_ops
nf_log_ipv4_net_ops
nf_log_ipv6_net_ops
nf_log_netdev_net_ops
Nobody can send such a packet to a net before it's became
registered, nobody can send a packet after all netdevices
are unregistered. So, these pernet_operations are able
to be marked as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations use ebt_register_table() and
ebt_unregister_table() to act on the tables, which
are used as argument in ebt_do_table(), called from
ebtables hooks.
Since there are no net-related bridge packets in-flight,
when the init and exit methods are called, these
pernet_operations are safe to be executed in parallel
with any other.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Put back reference on CLUSTERIP configuration structure from the
error path, patch from Florian Westphal.
2) Put reference on CLUSTERIP configuration instead of freeing it,
another cpu may still be walking over it, also from Florian.
3) Refetch pointer to IPv6 header from nf_nat_ipv6_manip_pkt() given
packet manipulation may reallocation the skbuff header, from Florian.
4) Missing match size sanity checks in ebt_among, from Florian.
5) Convert BUG_ON to WARN_ON in ebtables, from Florian.
6) Sanity check userspace offsets from ebtables kernel, from Florian.
7) Missing checksum replace call in flowtable IPv4 DNAT, from Felix
Fietkau.
8) Bump the right stats on checksum error from bridge netfilter,
from Taehee Yoo.
9) Unset interface flag in IPv6 fib lookups otherwise we get
misleading routing lookup results, from Florian.
10) Missing sk_to_full_sk() in ip6_route_me_harder() from Eric Dumazet.
11) Don't allow devices to be part of multiple flowtables at the same
time, this may break setups.
12) Missing netlink attribute validation in flowtable deletion.
13) Wrong array index in nf_unregister_net_hook() call from error path
in flowtable addition path.
14) Fix FTP IPVS helper when NAT mangling is in place, patch from
Julian Anastasov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations only unregister nf hooks.
So, they are able to be marked as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations are similar to bond_net_ops. Exit method
unregisters all net bridge devices, and it looks like another
pernet_operations are not interested in foreign net bridge list.
So, it's possible to mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added on a port, a reference is taken on the
corresponding master VLAN entry. If it does not already exist, then it
is created and a reference taken.
However, in the second case a reference is not really taken when
CONFIG_REFCOUNT_FULL is enabled as refcount_inc() is replaced by
refcount_inc_not_zero().
Fix this by using refcount_set() on a newly created master VLAN entry.
Fixes: 2512775985 ("net, bridge: convert net_bridge_vlan.refcnt from atomic_t to refcount_t")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ip_rcv, IPSTATS_MIB_CSUMERRORS is increased when
checksum error is occurred.
bridge netfilter routine should increase IPSTATS_MIB_CSUMERRORS.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We need to make sure the offsets are not out of range of the
total size.
Also check that they are in ascending order.
The WARN_ON triggered by syzkaller (it sets panic_on_warn) is
changed to also bail out, no point in continuing parsing.
Briefly tested with simple ruleset of
-A INPUT --limit 1/s' --log
plus jump to custom chains using 32bit ebtables binary.
Reported-by: <syzbot+845a53d13171abf8bf29@syzkaller.appspotmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All of these conditions are not fatal and should have
been WARN_ONs from the get-go.
Convert them to WARN_ONs and bail out.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ebt_among is special, it has a dynamic match size and is exempt
from the central size checks.
Therefore it must check that the size of the match structure
provided from userspace is sane by making sure em->match_size
is at least the minimum size of the expected structure.
The module has such a check, but its only done after accessing
a structure that might be out of bounds.
tested with: ebtables -A INPUT ... \
--among-dst fe:fe:fe:fe:fe:fe
--among-dst fe:fe:fe:fe:fe:fe --among-src fe:fe:fe:fe:ff:f,fe:fe:fe:fe:fe:fb,fe:fe:fe:fe:fc:fd,fe:fe:fe:fe:fe:fd,fe:fe:fe:fe:fe:fe
--among-src fe:fe:fe:fe:ff:f,fe:fe:fe:fe:fe:fa,fe:fe:fe:fe:fe:fd,fe:fe:fe:fe:fe:fe,fe:fe:fe:fe:fe:fe
Reported-by: <syzbot+fe0b19af568972814355@syzkaller.appspotmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains large batch with Netfilter fixes for
your net tree, mostly due to syzbot report fixups and pr_err()
ratelimiting, more specifically, they are:
1) Get rid of superfluous unnecessary check in x_tables before vmalloc(),
we don't hit BUG there anymore, patch from Michal Hock, suggested by
Andrew Morton.
2) Race condition in proc file creation in ipt_CLUSTERIP, from Cong Wang.
3) Drop socket lock that results in circular locking dependency, patch
from Paolo Abeni.
4) Drop packet if case of malformed blob that makes backpointer jump
in x_tables, from Florian Westphal.
5) Fix refcount leak due to race in ipt_CLUSTERIP in
clusterip_config_find_get(), from Cong Wang.
6) Several patches to ratelimit pr_err() for x_tables since this can be
a problem where CAP_NET_ADMIN semantics can protect us in untrusted
namespace, from Florian Westphal.
7) Missing .gitignore update for new autogenerated asn1 state machine
for the SNMP NAT helper, from Zhu Lingshan.
8) Missing timer initialization in xt_LED, from Paolo Abeni.
9) Do not allow negative port range in NAT, also from Paolo.
10) Lock imbalance in the xt_hashlimit rate match mode, patch from
Eric Dumazet.
11) Initialize workqueue before timer in the idletimer match,
from Eric Dumazet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ebt_among still uses pr_err -- these errors indicate ebtables tool bug,
not a usage error.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now br_sysfs_if file flush doesn't have attr show. To read it will
cause kernel panic after users chmod u+r this file.
Xiong found this issue when running the commands:
ip link add br0 type bridge
ip link add type veth
ip link set veth0 master br0
chmod u+r /sys/devices/virtual/net/veth0/brport/flush
timeout 3 cat /sys/devices/virtual/net/veth0/brport/flush
kernel crashed with NULL a pointer dereference call trace.
This patch is to fix it by return -EINVAL when brport_attr->show
is null, just the same as the check for brport_attr->store in
brport_store().
Fixes: 9cf637473c ("bridge: add sysfs hook to flush forwarding table")
Reported-by: Xiong Zhou <xzhou@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With gcc-4.1.2.:
net/bridge/br_fdb.c: In function ‘br_fdb_sync_static’:
net/bridge/br_fdb.c:996: warning: ‘err’ may be used uninitialized in this function
Indeed, if the list is empty, err will be uninitialized, and will be
propagated up as the function return value.
Fix this by preinitializing err to zero.
Fixes: eb7935830d ("net: bridge: use rhashtable for fdbs")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return statements in functions returning bool should use
true/false instead of 1/0.
This issue was detected with the help of Coccinelle.
Fixes: 85b3526932 ("bridge: Fix build error when IGMP_SNOOPING is not enabled")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several reasons for this:
* Several modules maintain internal version numbers, that they print at
boot/module load time, that are not exposed to userspace, as a
primitive mechanism to make revision number control from the earlier
days of Netfilter.
* IPset shows the protocol version at boot/module load time, instead
display this via module description, as Jozsef suggested.
* Remove copyright notice at boot/module load time in two spots, the
Netfilter codebase is a collective development effort, if we would
have to display copyrights for each contributor at boot/module load
time for each extensions we have, we would probably fill up logs with
lots of useless information - from a technical standpoint.
So let's be consistent and remove them all.
Acked-by: Florian Westphal <fw@strlen.de>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Remove the infrastructure to register/unregister nft_af_info structure,
this structure stores no useful information anymore.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now that we have a single table list for each netns, we can get rid of
one pointer per family and the global afinfo list, thus, shrinking
struct netns for nftables that now becomes 64 bytes smaller.
And call __nft_release_afinfo() from __net_exit path accordingly to
release netnamespace objects on removal.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We already validate the hook through bitmask, so this check is
superfluous. When removing this, this patch is also fixing a bug in the
new flowtable codebase, since ctx->afi points to the table family
instead of the netdev family which is where the flowtable is really
hooked in.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This abstraction has no clients anymore, remove it.
This is what remains from previous authors, so correct copyright
statement after recent modifications and code removal.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We cannot make a direct call to nf_ip6_reroute() because that would result
in autoloading the 'ipv6' module because of symbol dependencies.
Therefore, define reroute indirection in nf_ipv6_ops where this really
belongs to.
For IPv4, we can indeed make a direct function call, which is faster,
given IPv4 is built-in in the networking code by default. Still,
CONFIG_INET=n and CONFIG_NETFILTER=y is possible, so define empty inline
stub for IPv4 in such case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We cannot make a direct call to nf_ip6_route() because that would result
in autoloading the 'ipv6' module because of symbol dependencies.
Therefore, define route indirection in nf_ipv6_ops where this really
belongs to.
For IPv4, we can indeed make a direct function call, which is faster,
given IPv4 is built-in in the networking code by default. Still,
CONFIG_INET=n and CONFIG_NETFILTER=y is possible, so define empty inline
stub for IPv4 in such case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is only used by nf_queue.c and this function comes with no symbol
dependencies with IPv6, it just refers to structure layouts. Therefore,
we can replace it by a direct function call from where it belongs.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We cannot make a direct call to nf_ip6_checksum_partial() because that
would result in autoloading the 'ipv6' module because of symbol
dependencies. Therefore, define checksum_partial indirection in
nf_ipv6_ops where this really belongs to.
For IPv4, we can indeed make a direct function call, which is faster,
given IPv4 is built-in in the networking code by default. Still,
CONFIG_INET=n and CONFIG_NETFILTER=y is possible, so define empty inline
stub for IPv4 in such case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We cannot make a direct call to nf_ip6_checksum() because that would
result in autoloading the 'ipv6' module because of symbol dependencies.
Therefore, define checksum indirection in nf_ipv6_ops where this really
belongs to.
For IPv4, we can indeed make a direct function call, which is faster,
given IPv4 is built-in in the networking code by default. Still,
CONFIG_INET=n and CONFIG_NETFILTER=y is possible, so define empty inline
stub for IPv4 in such case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
They don't belong to the family definition, move them to the filter
chain type definition instead.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since NFPROTO_INET is handled from the core, we don't need to maintain
extra infrastructure in nf_tables to handle the double hook
registration, one for IPv4 and another for IPv6.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of calling this function from the family specific variant, this
reduces the code size in the fast path for the netdev, bridge and inet
families. After this change, we must call nft_set_pktinfo() upfront from
the chain hook indirection.
Before:
text data bss dec hex filename
2145 208 0 2353 931 net/netfilter/nf_tables_netdev.o
After:
text data bss dec hex filename
2125 208 0 2333 91d net/netfilter/nf_tables_netdev.o
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
no need to define hook points if the family isn't supported.
Because we need these hooks for either nftables, arp/ebtables
or the 'call-iptables' hack we have in the bridge layer add two
new dependencies, NETFILTER_FAMILY_{ARP,BRIDGE}, and have the
users select them.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
struct net contains:
struct nf_hook_entries __rcu *hooks[NFPROTO_NUMPROTO][NF_MAX_HOOKS];
which store the hook entry point locations for the various protocol
families and the hooks.
Using array results in compact c code when doing accesses, i.e.
x = rcu_dereference(net->nf.hooks[pf][hook]);
but its also wasting a lot of memory, as most families are
not used.
So split the array into those families that are used, which
are only 5 (instead of 13). In most cases, the 'pf' argument is
constant, i.e. gcc removes switch statement.
struct net before:
/* size: 5184, cachelines: 81, members: 46 */
after:
/* size: 4672, cachelines: 73, members: 46 */
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use
%pM to print MAC
mac_pton() to convert it from ASCII to binary format, and
ether_addr_copy() to copy.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The early call to br_stp_change_bridge_id in bridge's newlink can cause
a memory leak if an error occurs during the newlink because the fdb
entries are not cleaned up if a different lladdr was specified, also
another minor issue is that it generates fdb notifications with
ifindex = 0. Another unrelated memory leak is the bridge sysfs entries
which get added on NETDEV_REGISTER event, but are not cleaned up in the
newlink error path. To remove this special case the call to
br_stp_change_bridge_id is done after netdev register and we cleanup the
bridge on changelink error via br_dev_delete to plug all leaks.
This patch makes netlink bridge destruction on newlink error the same as
dellink and ioctl del which is necessary since at that point we have a
fully initialized bridge device.
To reproduce the issue:
$ ip l add br0 address 00:11:22:33:44:55 type bridge group_fwd_mask 1
RTNETLINK answers: Invalid argument
$ rmmod bridge
[ 1822.142525] =============================================================================
[ 1822.143640] BUG bridge_fdb_cache (Tainted: G O ): Objects remaining in bridge_fdb_cache on __kmem_cache_shutdown()
[ 1822.144821] -----------------------------------------------------------------------------
[ 1822.145990] Disabling lock debugging due to kernel taint
[ 1822.146732] INFO: Slab 0x0000000092a844b2 objects=32 used=2 fp=0x00000000fef011b0 flags=0x1ffff8000000100
[ 1822.147700] CPU: 2 PID: 13584 Comm: rmmod Tainted: G B O 4.15.0-rc2+ #87
[ 1822.148578] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 1822.150008] Call Trace:
[ 1822.150510] dump_stack+0x78/0xa9
[ 1822.151156] slab_err+0xb1/0xd3
[ 1822.151834] ? __kmalloc+0x1bb/0x1ce
[ 1822.152546] __kmem_cache_shutdown+0x151/0x28b
[ 1822.153395] shutdown_cache+0x13/0x144
[ 1822.154126] kmem_cache_destroy+0x1c0/0x1fb
[ 1822.154669] SyS_delete_module+0x194/0x244
[ 1822.155199] ? trace_hardirqs_on_thunk+0x1a/0x1c
[ 1822.155773] entry_SYSCALL_64_fastpath+0x23/0x9a
[ 1822.156343] RIP: 0033:0x7f929bd38b17
[ 1822.156859] RSP: 002b:00007ffd160e9a98 EFLAGS: 00000202 ORIG_RAX: 00000000000000b0
[ 1822.157728] RAX: ffffffffffffffda RBX: 00005578316ba090 RCX: 00007f929bd38b17
[ 1822.158422] RDX: 00007f929bd9ec60 RSI: 0000000000000800 RDI: 00005578316ba0f0
[ 1822.159114] RBP: 0000000000000003 R08: 00007f929bff5f20 R09: 00007ffd160e8a11
[ 1822.159808] R10: 00007ffd160e9860 R11: 0000000000000202 R12: 00007ffd160e8a80
[ 1822.160513] R13: 0000000000000000 R14: 0000000000000000 R15: 00005578316ba090
[ 1822.161278] INFO: Object 0x000000007645de29 @offset=0
[ 1822.161666] INFO: Object 0x00000000d5df2ab5 @offset=128
Fixes: 30313a3d57 ("bridge: Handle IFLA_ADDRESS correctly when creating bridge device")
Fixes: 5b8d5429da ("bridge: netlink: register netdevice before executing changelink")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch the bridge used a fixed 256 element hash table which
was fine for small use cases (in my tests it starts to degrade
above 1000 entries), but it wasn't enough for medium or large
scale deployments. Modern setups have thousands of participants in a
single bridge, even only enabling vlans and adding a few thousand vlan
entries will cause a few thousand fdbs to be automatically inserted per
participating port. So we need to scale the fdb table considerably to
cope with modern workloads, and this patch converts it to use a
rhashtable for its operations thus improving the bridge scalability.
Tests show the following results (10 runs each), at up to 1000 entries
rhashtable is ~3% slower, at 2000 rhashtable is 30% faster, at 3000 it
is 2 times faster and at 30000 it is 50 times faster.
Obviously this happens because of the properties of the two constructs
and is expected, rhashtable keeps pretty much a constant time even with
10000000 entries (tested), while the fixed hash table struggles
considerably even above 10000.
As a side effect this also reduces the net_bridge struct size from 3248
bytes to 1344 bytes. Also note that the key struct is 8 bytes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
all of these can be compiled as a module, so use new
_module version to make sure module can no longer be removed
while callback/dump is in use.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first member of an IPSEC route bundle chain sets it's dst->path to
the underlying ipv4/ipv6 route that carries the bundle.
Stated another way, if one were to follow the xfrm_dst->child chain of
the bundle, the final non-NULL pointer would be the path and point to
either an ipv4 or an ipv6 route.
This is largely used to make sure that PMTU events propagate down to
the correct ipv4 or ipv6 route.
When we don't have the top of an IPSEC bundle 'dst->path == dst'.
Move it down into xfrm_dst and key off of dst->xfrm.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Found another missing port flag policy entry for IFLA_BRPORT_VLAN_TUNNEL
so add it now.
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the host joins or leaves a multicast group, use switchdev to add
an object to the hardware to forward traffic for the group to the
host.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The host can join or leave a multicast group on the brX interface, as
indicated by IGMP snooping. This is tracked within the bridge
multicast code. Send a notification when this happens, in the same way
a notification is sent when a port of the bridge joins/leaves a group
because of IGMP snooping.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The boolean mglist indicates the host has joined a particular
multicast group on the bridge interface. It is badly named, obscuring
what is means. Rename it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree, they are:
1) Speed up table replacement on busy systems with large tables
(and many cores) in x_tables. Now xt_replace_table() synchronizes by
itself by waiting until all cpus had an even seqcount and we use no
use seqlock when fetching old counters, from Florian Westphal.
2) Add nf_l4proto_log_invalid() and nf_ct_l4proto_log_invalid() to speed
up packet processing in the fast path when logging is not enabled, from
Florian Westphal.
3) Precompute masked address from configuration plane in xt_connlimit,
from Florian.
4) Don't use explicit size for set selection if performance set policy
is selected.
5) Allow to get elements from an existing set in nf_tables.
6) Fix incorrect check in nft_hash_deactivate(), from Florian.
7) Cache netlink attribute size result in l4proto->nla_size, from
Florian.
8) Handle NFPROTO_INET in nf_ct_netns_get() from conntrack core.
9) Use power efficient workqueue in conntrack garbage collector, from
Vincent Guittot.
10) Remove unnecessary parameter, in conntrack l4proto functions, also
from Florian.
11) Constify struct nf_conntrack_l3proto definitions, from Florian.
12) Remove all typedefs in nf_conntrack_h323 via coccinelle semantic
patch, from Harsha Sharma.
13) Don't store address in the rbtree nodes in xt_connlimit, they are
never used, from Florian.
14) Fix out of bound access in the conntrack h323 helper, patch from
Eric Sesterhenn.
15) Print symbols for the address returned with %pS in IPVS, from
Helge Deller.
16) Proc output should only display its own netns in IPVS, from
KUWAZAWA Takuya.
17) Small clean up in size_entry_mwt(), from Colin Ian King.
18) Use test_and_clear_bit from nf_nat_proto_clean() instead of separated
non-atomic test and then clear bit, from Florian Westphal.
19) Consolidate prefix length maps in ipset, from Aaron Conole.
20) Fix sparse warnings in ipset, from Jozsef Kadlecsik.
21) Simplify list_set_memsize(), from simran singhal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
buf is initialized to buf_start and then set on the next statement
to buf_start + offsets[i]. Clean this up to just initialize buf
to buf_start + offsets[i] to clean up the clang build warning:
"Value stored to 'buf' during its initialization is never read"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
switch to using the new timer_setup() and from_timer() api's.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switch to using the new timer_setup() and from_timer() api's.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan9303 driver defines eth_stp_addr as a synonym to
eth_reserved_addr_base to get the STP ethernet address 01:80:c2:00:00:00.
eth_reserved_addr_base is also used to define the start of Bridge Reserved
ethernet address range, which happen to be the STP address.
br_dev_setup refer to eth_reserved_addr_base as a definition of STP
address.
Clean up by:
- Move the eth_stp_addr definition to linux/etherdevice.h
- Use eth_stp_addr instead of eth_reserved_addr_base in br_dev_setup.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the bridge device doesn't generate any notifications upon vlan
modifications on itself because it doesn't use the generic bridge
notifications.
With the recent changes we know if anything was modified in the vlan config
thus we can generate a notification when necessary for the bridge device
so add support to br_ifinfo_notify() similar to how other combined
functions are done - if port is present it takes precedence, otherwise
notify about the bridge. I've explicitly marked the locations where the
notification should be always for the port by setting bridge to NULL.
I've also taken the liberty to rearrange each modified function's local
variables in reverse xmas tree as well.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an entry for IFLA_BRPORT_NEIGH_SUPPRESS to bridge port policies.
Fixes: 821f1b21ca ("bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch there was no way to tell if the vlan add operation
actually changed anything, thus we would always generate a notification
on adds. Let's make the notifications more precise and generate them
only if anything changed, so use the new bool parameter to signal that the
vlan was updated. We cannot return an error because there are valid use
cases that will be broken (e.g. overlapping range add) and also we can't
risk masking errors due to calls into drivers for vlan add which can
potentially return anything.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch we had cases that either sent notifications when there
were in fact no changes (e.g. non-existent vlan delete) or didn't send
notifications when there were changes (e.g. vlan add range with an error in
the middle, port flags change + vlan update error). This patch sends down
a boolean to the functions setlink/dellink use and if there is even a
single configuration change (port flag, vlan add/del, port state) then
we always send a notification. This is all done to keep backwards
compatibility with the opportunistic vlan delete, where one could
specify a vlan range that has missing vlans inside and still everything
in that range will be cleared, this is mostly used to clear the whole
vlan config with a single call, i.e. range 1-4094.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit dc709f3757 ("rtnetlink: bring NETDEV_CHANGEUPPER event
process back in rtnetlink_event"), rtnetlink_event would process the
NETDEV_CHANGEUPPER event and send a notification to userspace.
In add_del_if, it would generate NETDEV_CHANGEUPPER event by whether
netdev_master_upper_dev_link or netdev_upper_dev_unlink. There's
no need to call rtmsg_ifinfo to send the notification any more.
So this patch is to remove it from add_del_if also to avoid redundant
notifications.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
When vlan tunnels were introduced, vlan range errors got silently
dropped and instead 0 was returned always. Restore the previous
behaviour and return errors to user-space.
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an access function that, given a bridge netdevice, returns whether the
bridge device is currently an mrouter or not. The function uses the already
existing br_multicast_is_router function to check that.
This function is needed in order to allow ports that join an already
existing bridge to know the current mrouter state of the bridge device.
Together with the bridge device mrouter ports switchdev notifications, it
is possible to have full offloading of the semantics of the bridge device
mcast router state.
Due to the fact that the bridge multicast router status can change in
packet RX path, take the multicast_router bridge spinlock to protect the
read.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SWITCHDEV_ATTR_ID_BRIDGE_MROUTER switchdev notification type, used
to indicate whether the bridge is or isn't mrouter. Notify when the bridge
changes its state, similarly to the already existing bridged port mrouter
notifications.
The notification uses the switchdev_attr.u.mrouter boolean flag to indicate
the current bridge mrouter status. Thus, it only indicates whether the
bridge is currently used as an mrouter or not, and does not indicate the
exact mrouter state of the bridge (learning, permanent, etc.).
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids flooding and proxies ndisc packets
for BR_NEIGH_SUPPRESS ports.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids flooding and proxies arp packets
for BR_NEIGH_SUPPRESS ports.
Moves existing br_do_proxy_arp to br_do_proxy_suppress_arp
to support both proxy arp and neigh suppress.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new bridge port flag BR_NEIGH_SUPPRESS to
suppress arp and nd flood on bridge ports. It implements
rfc7432, section 10.
https://tools.ietf.org/html/rfc7432#section-10
for ethernet VPN deployments. It is similar to the existing
BR_PROXYARP* flags but has a few semantic differences to conform
to EVPN standard. Unlike the existing flags, this new flag suppresses
flood of all neigh discovery packets (arp and nd) to tunnel ports.
Supports both vlan filtering and non-vlan filtering bridges.
In case of EVPN, it is mainly used to avoid flooding
of arp and nd packets to tunnel ports like vxlan.
This patch adds netlink and sysfs support to set this bridge port
flag.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack arg to br_add_if. Add messages for a couple of failures
and pass arg to netdev_master_upper_dev_link.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack arg to netdev_upper_dev_link and netdev_master_upper_dev_link
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack to do_set_master and down to ndo_add_slave
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for ebt_in_hook to be triggered before ebt_table is assigned
resulting in a NULL-pointer dereference. Make sure hooks are
registered as the last step.
Fixes: aee12a0a37 ("ebtables: remove nf_hook_register usage")
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We need to be able to transparently forward most link-local frames via
tunnels (e.g. vxlan, qinq). Currently the bridge's group_fwd_mask has a
mask which restricts the forwarding of STP and LACP, but we need to be able
to forward these over tunnels and control that forwarding on a per-port
basis thus add a new per-port group_fwd_mask option which only disallows
mac pause frames to be forwarded (they're always dropped anyway).
The patch does not change the current default situation - all of the others
are still restricted unless configured for forwarding.
We have successfully tested this patch with LACP and STP forwarding over
VxLAN and qinq tunnels.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is a difference in netlink events received when an
interface is modified through bridge ioctl() or through netlink. This
patch generates additional events when an interface is added to or
removed from a bridge via ioctl().
When adding then removing an interface from a bridge with netlink, we
get:
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master bridge0 state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master bridge0 state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master bridge0 state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
Deleted 5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
When using ioctl():
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master bridge0 state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master bridge0 state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master bridge0 state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
Deleted 5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
Without this patch, the last netlink notification is not sent.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 00ba4cb36d.
Discussion with David Ahern determined that this change is
actually not needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when an interface is released from a bridge via
ioctl(), we get a RTM_DELLINK event through netlink:
Deleted 2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 6e:23:c2:54:3a:b3
Userspace has to interpret that as a removal from the bridge, not as a
complete removal of the interface. When an bridged interface is
completely removed, we get two events:
Deleted 2: dummy0: <BROADCAST,NOARP> mtu 1500 master bridge0 state DOWN
link/ether 6e:23:c2:54:3a:b3
Deleted 2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default
link/ether 6e:23:c2:54:3a:b3 brd ff:ff:ff:ff:ff:ff
In constrast, when an interface is released from a bond, we get a
RTM_NEWLINK with only the new characteristics (no master):
3: dummy1: <BROADCAST,NOARP,SLAVE,UP,LOWER_UP> mtu 1500 qdisc noqueue master bond0 state UNKNOWN group default
link/ether ae:dc:7a:8c:9a:3c brd ff:ff:ff:ff:ff:ff
3: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether ae:dc:7a:8c:9a:3c brd ff:ff:ff:ff:ff:ff
4: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether ae:dc:7a:8c:9a:3c brd ff:ff:ff:ff:ff:ff
3: dummy1: <BROADCAST,NOARP> mtu 1500 qdisc noqueue state DOWN group default
link/ether ae:dc:7a:8c:9a:3c brd ff:ff:ff:ff:ff:ff
3: dummy1: <BROADCAST,NOARP> mtu 1500 qdisc noqueue state DOWN group default
link/ether ca:c8:7b:66:f8:25 brd ff:ff:ff:ff:ff:ff
4: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether ae:dc:7a:8c:9a:3c brd ff:ff:ff:ff:ff:ff
Userland may be confused by the fact we say a link is deleted while
its characteristics are only modified. A first solution would have
been to turn the RTM_DELLINK event in del_nbp() into a RTM_NEWLINK
event. However, maybe some piece of userland is relying on this
RTM_DELLINK to detect when a bridged interface is released. Instead,
we also emit a RTM_NEWLINK event once the interface is
released (without master info).
Deleted 2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 8a:bb:e7:94:b1:f8
2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether 8a:bb:e7:94:b1:f8 brd ff:ff:ff:ff:ff:ff
This is done only when using ioctl(). When using Netlink, such an
event is already automatically emitted in do_setlink().
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using ifdef in the C file.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes CONFIG_NETFILTER_DEBUG and _ASSERT() macros as they
are no longer required. Replace _ASSERT() macros with WARN_ON().
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Basically, updates to the conntrack core, enhancements for
nf_tables, conversion of netfilter hooks from linked list to array to
improve memory locality and asorted improvements for the Netfilter
codebase. More specifically, they are:
1) Add expection to hashes after timer initialization to prevent
access from another CPU that walks on the hashes and calls
del_timer(), from Florian Westphal.
2) Don't update nf_tables chain counters from hot path, this is only
used by the x_tables compatibility layer.
3) Get rid of nested rcu_read_lock() calls from netfilter hook path.
Hooks are always guaranteed to run from rcu read side, so remove
nested rcu_read_lock() where possible. Patch from Taehee Yoo.
4) nf_tables new ruleset generation notifications include PID and name
of the process that has updated the ruleset, from Phil Sutter.
5) Use skb_header_pointer() from nft_fib, so we can reuse this code from
the nf_family netdev family. Patch from Pablo M. Bermudo.
6) Add support for nft_fib in nf_tables netdev family, also from Pablo.
7) Use deferrable workqueue for conntrack garbage collection, to reduce
power consumption, from Patch from Subash Abhinov Kasiviswanathan.
8) Add nf_ct_expect_iterate_net() helper and use it. From Florian
Westphal.
9) Call nf_ct_unconfirmed_destroy only from cttimeout, from Florian.
10) Drop references on conntrack removal path when skbuffs has escaped via
nfqueue, from Florian.
11) Don't queue packets to nfqueue with dying conntrack, from Florian.
12) Constify nf_hook_ops structure, from Florian.
13) Remove neededlessly branch in nf_tables trace code, from Phil Sutter.
14) Add nla_strdup(), from Phil Sutter.
15) Rise nf_tables objects name size up to 255 chars, people want to use
DNS names, so increase this according to what RFC 1035 specifies.
Patch series from Phil Sutter.
16) Kill nf_conntrack_default_on, it's broken. Default on conntrack hook
registration on demand, suggested by Eric Dumazet, patch from Florian.
17) Remove unused variables in compat_copy_entry_from_user both in
ip_tables and arp_tables code. Patch from Taehee Yoo.
18) Constify struct nf_conntrack_l4proto, from Julia Lawall.
19) Constify nf_loginfo structure, also from Julia.
20) Use a single rb root in connlimit, from Taehee Yoo.
21) Remove unused netfilter_queue_init() prototype, from Taehee Yoo.
22) Use audit_log() instead of open-coding it, from Geliang Tang.
23) Allow to mangle tcp options via nft_exthdr, from Florian.
24) Allow to fetch TCP MSS from nft_rt, from Florian. This includes
a fix for a miscalculation of the minimal length.
25) Simplify branch logic in h323 helper, from Nick Desaulniers.
26) Calculate netlink attribute size for conntrack tuple at compile
time, from Florian.
27) Remove protocol name field from nf_conntrack_{l3,l4}proto structure.
From Florian.
28) Remove holes in nf_conntrack_l4proto structure, so it becomes
smaller. From Florian.
29) Get rid of print_tuple() indirection for /proc conntrack listing.
Place all the code in net/netfilter/nf_conntrack_standalone.c.
Patch from Florian.
30) Do not built in print_conntrack() if CONFIG_NF_CONNTRACK_PROCFS is
off. From Florian.
31) Constify most nf_conntrack_{l3,l4}proto helper functions, from
Florian.
32) Fix broken indentation in ebtables extensions, from Colin Ian King.
33) Fix several harmless sparse warning, from Florian.
34) Convert netfilter hook infrastructure to use array for better memory
locality, joint work done by Florian and Aaron Conole. Moreover, add
some instrumentation to debug this.
35) Batch nf_unregister_net_hooks() calls, to call synchronize_net once
per batch, from Florian.
36) Get rid of noisy logging in ICMPv6 conntrack helper, from Florian.
37) Get rid of obsolete NFDEBUG() instrumentation, from Varsha Rao.
38) Remove unused code in the generic protocol tracker, from Davide
Caratti.
I think I will have material for a second Netfilter batch in my queue if
time allow to make it fit in this merge window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6bc506b4fb ("bridge: switchdev: Add forward mark support for
stacked devices") added the 'offload_fwd_mark' bit to the skb in order
to allow drivers to indicate to the bridge driver that they already
forwarded the packet in L2.
In case the bit is set, before transmitting the packet from each port,
the port's mark is compared with the mark stored in the skb's control
block. If both marks are equal, we know the packet arrived from a switch
device that already forwarded the packet and it's not re-transmitted.
However, if the packet is transmitted from the bridge device itself
(e.g., br0), we should clear the 'offload_fwd_mark' bit as the mark
stored in the skb's control block isn't valid.
This scenario can happen in rare cases where a packet was trapped during
L3 forwarding and forwarded by the kernel to a bridge device.
Fixes: 6bc506b4fb ("bridge: switchdev: Add forward mark support for stacked devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Yotam Gigi <yotamg@mellanox.com>
Tested-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends bridge fdb table tracepoints to also cover
learned fdb entries in the br_fdb_update path. Note that
unlike other tracepoints I have moved this to when the fdb
is modified because this is in the datapath and can generate
a lot of noise in the trace output. br_fdb_update is also called
from added_by_user context in the NTF_USE case which is already
traced ..hence the !added_by_user check.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few useful tracepoints to trace bridge forwarding
database updates.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this const as it is only passed to a const argument of the function
ebt_register_table.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts the storage and layout of netfilter hook entries from a
linked list to an array. After this commit, hook entries will be
stored adjacent in memory. The next pointer is no longer required.
The ops pointers are stored at the end of the array as they are only
used in the register/unregister path and in the legacy br_netfilter code.
nf_unregister_net_hooks() is slower than needed as it just calls
nf_unregister_net_hook in a loop (i.e. at least n synchronize_net()
calls), this will be addressed in followup patch.
Test setup:
- ixgbe 10gbit
- netperf UDP_STREAM, 64 byte packets
- 5 hooks: (raw + mangle prerouting, mangle+filter input, inet filter):
empty mangle and raw prerouting, mangle and filter input hooks:
353.9
this patch:
364.2
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The returns on some if statements are not indented correctly,
add in the missing tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This change allows us to later indicate to rtnetlink core that certain
doit functions should be called without acquiring rtnl_mutex.
This change should have no effect, we simply replace the last (now
unused) calcit argument with the new flag.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point no driver supports FDB add/del through switchdev object
but rather via notification chain, thus, it is removed.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer place these on a list so they can be const.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
With 802.1ad support the vlan_ingress code started checking for vlan
protocol mismatch which causes the current tag to be inserted and the
bridge vlan protocol & pvid to be set. The vlan tag insertion changes
the skb mac_header and thus the lookup mac dest pointer which was loaded
prior to calling br_allowed_ingress in br_handle_frame_finish is VLAN_HLEN
bytes off now, pointing to the last two bytes of the destination mac and
the first four of the source mac causing lookups to always fail and
broadcasting all such packets to all ports. Same thing happens for locally
originated packets when passing via br_dev_xmit. So load the dest pointer
after the vlan checks and possible skb change.
Fixes: 8580e2117c ("bridge: Prepare for 802.1ad vlan filtering support")
Reported-by: Anitha Narasimha Murthy <anitha@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains two Netfilter fixes for your net tree,
they are:
1) Fix memleak from netns release path of conntrack protocol trackers,
patch from Liping Zhang.
2) Uninitialized flags field in ebt_log, that results in unpredictable
logging format in ebtables, also from Liping.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
current code silently ignores change of port in the request
message. This patch makes sure the port is modified and
notification is sent to userspace.
Fixes: cf6b8e1eed ("bridge: add API to notify bridge driver of learned FBD on offloaded device")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. This batch contains connection tracking updates for the cleanup
iteration path, patches from Florian Westphal:
X) Skip unconfirmed conntracks in nf_ct_iterate_cleanup_net(), just set
dying bit to let the CPU release them.
X) Add nf_ct_iterate_destroy() to be used on module removal, to kill
conntrack from all namespace.
X) Restart iteration on hashtable resizing, since both may occur at
the same time.
X) Use the new nf_ct_iterate_destroy() to remove conntrack with NAT
mapping on module removal.
X) Use nf_ct_iterate_destroy() to remove conntrack entries helper
module removal, from Liping Zhang.
X) Use nf_ct_iterate_cleanup_net() to remove the timeout extension
if user requests this, also from Liping.
X) Add net_ns_barrier() and use it from FTP helper, so make sure
no concurrent namespace removal happens at the same time while
the helper module is being removed.
X) Use NFPROTO_MAX in layer 3 conntrack protocol array, to reduce
module size. Same thing in nf_tables.
Updates for the nf_tables infrastructure:
X) Prepare usage of the extended ACK reporting infrastructure for
nf_tables.
X) Remove unnecessary forward declaration in nf_tables hash set.
X) Skip set size estimation if number of element is not specified.
X) Changes to accomodate a (faster) unresizable hash set implementation,
for anonymous sets and dynamic size fixed sets with no timeouts.
X) Faster lookup function for unresizable hash table for 2 and 4
bytes key.
And, finally, a bunch of asorted small updates and cleanups:
X) Do not hold reference to netdev from ipt_CLUSTER, instead subscribe
to device events and look up for index from the packet path, this
is fixing an issue that is present since the very beginning, patch
from Xin Long.
X) Use nf_register_net_hook() in ipt_CLUSTER, from Florian Westphal.
X) Use ebt_invalid_target() whenever possible in the ebtables tree,
from Gao Feng.
X) Calm down compilation warning in nf_dup infrastructure, patch from
stephen hemminger.
X) Statify functions in nftables rt expression, also from stephen.
X) Update Makefile to use canonical method to specify nf_tables-objs.
From Jike Song.
X) Use nf_conntrack_helpers_register() in amanda and H323.
X) Space cleanup for ctnetlink, from linzhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2645 896 0 3541 dd5 net/bridge/br_sysfs_br.o
File size After adding 'const':
text data bss dec hex filename
2701 832 0 3533 dcd net/bridge/br_sysfs_br.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"struct nf_loginfo li;" is a local variable, so we should set the flags
to 0 explicitly, else, packets maybe truncated unexpectedly when copied
to the userspace.
Fixes: 7643507fe8 ("netfilter: xt_NFLOG: nflog-range does not truncate packets")
Cc: Vishwanath Pai <vpai@akamai.com>
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new helper function ebt_invalid_target instead of the old
macro INVALID_TARGET and other duplicated codes to enhance the readability.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new static FDB is added to the bridge a notification is sent to
the driver for offload. In case of successful offload the driver should
notify the bridge back, which in turn should mark the FDB as offloaded.
Currently, externally learned is equivalent for being offloaded which is
not correct due to the fact that FDBs which are added from user-space are
also marked as externally learned. In order to specify if an FDB was
successfully offloaded a new flag is introduced.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bridge doesn't notify the underlying devices about new
FDBs learned. The FDB sync is placed on the switchdev notifier chain
because devices may potentially learn FDB that are not directly related
to their ports, for example:
1. Mixed SW/HW bridge - FDBs that point to the ASICs external devices
should be offloaded as CPU traps in order to
perform forwarding in slow path.
2. EVPN - Externally learned FDBs for the vtep device.
Notification is sent only about static FDB add/del. This is done due
to fact that currently this is the only scenario supported by switch
drivers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation to moving the switchdev notifier chain
to be atomic. The FDB external learning should be called under rtnl
or rcu.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the flood, learning and learning_sync port attributes are
offloaded by setting the SELF flag. Add support for offloading the
flood and learning attribute through the bridge code. In case of
setting an unsupported flag on a offloded port the operation will
fail.
The learning_sync attribute doesn't have any software representation
and cannot be offloaded through the bridge code.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
We might call br_afspec() with p == NULL which is a valid use case if
the action is on the bridge device itself, but the bridge tunnel code
dereferences the p pointer without checking, so check if p is null
first.
Reported-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the transition of NO_STP -> KERNEL_STP was fixed by always calling
mod_timer in br_stp_start, it introduced a new regression which causes
the timer to be armed even when the bridge is down, and since we stop
the timers in its ndo_stop() function, they never get disabled if the
device is destroyed before it's upped.
To reproduce:
$ while :; do ip l add br0 type bridge hello_time 100; brctl stp br0 on;
ip l del br0; done;
CC: Xin Long <lucien.xin@gmail.com>
CC: Ivan Vecera <cera@cera.cz>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Fixes: 6d18c732b9 ("bridge: start hello_timer when enabling KERNEL_STP in br_stp_start")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During enslavement to a bridge, after the CHANGEUPPER is sent, the
multicast enabled state of the bridge isn't propagated down to the
offloading driver unless it's changed.
This patch allows such drivers to query the multicast enabled state from
the bridge, so that they'll be able to correctly configure their flood
tables during port enslavement.
In case multicast is disabled, unregistered multicast packets can be
treated as broadcast and be flooded through all the bridge ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's useful for drivers supporting bridge offload to be able to query
the bridge's VLAN filtering state.
Currently, upon enslavement to a bridge master, the offloading driver
will only learn about the bridge's VLAN filtering state after the bridge
device was already linked with its slave.
Being able to query the bridge's VLAN filtering state allows such
drivers to forbid enslavement in case resource couldn't be allocated for
a VLAN-aware bridge and also choose the correct initialization routine
for the enslaved port, which is dependent on the bridge type.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current bridge code incorrectly handles starting/stopping of hello and
hold timers during STP enable/disable.
1. Timers are stopped in br_stp_start() during NO_STP->USER_STP
transition. The timers are already stopped in NO_STP state so
this is confusing no-op.
2. During USER_STP->NO_STP transition the timers are started. This
does not make sense and is confusion because the timer should not be
active in NO_STP state.
Cc: davem@davemloft.net
Cc: sashok@cumulusnetworks.com
Cc: stephen@networkplumber.org
Cc: bridge@lists.linux-foundation.org
Cc: lucien.xin@gmail.com
Cc: nikolay@cumulusnetworks.com
Signed-off-by: Ivan Vecera <cera@cera.cz>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 76b91c32dd ("bridge: stp: when using userspace stp stop
kernel hello and hold timers"), bridge would not start hello_timer if
stp_enabled is not KERNEL_STP when br_dev_open.
The problem is even if users set stp_enabled with KERNEL_STP later,
the timer will still not be started. It causes that KERNEL_STP can
not really work. Users have to re-ifup the bridge to avoid this.
This patch is to fix it by starting br->hello_timer when enabling
KERNEL_STP in br_stp_start.
As an improvement, it's also to start hello_timer again only when
br->stp_enabled is KERNEL_STP in br_hello_timer_expired, there is
no reason to start the timer again when it's NO_STP.
Fixes: 76b91c32dd ("bridge: stp: when using userspace stp stop kernel hello and hold timers")
Reported-by: Haidong Li <haili@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) When using IPVS in direct-routing mode, normal traffic from the LVS
host to a back-end server is sometimes incorrectly NATed on the way
back into the LVS host. Patch to fix this from Julian Anastasov.
2) Calm down clang compilation warning in ctnetlink due to type
mismatch, from Matthias Kaehlcke.
3) Do not re-setup NAT for conntracks that are already confirmed, this
is fixing a problem that was introduced in the previous nf-next batch.
Patch from Liping Zhang.
4) Do not allow conntrack helper removal from userspace cthelper
infrastructure if already in used. This comes with an initial patch
to introduce nf_conntrack_helper_put() that is required by this fix.
From Liping Zhang.
5) Zero the pad when copying data to userspace, otherwise iptables fails
to remove rules. This is a follow up on the patchset that sorts out
the internal match/target structure pointer leak to userspace. Patch
from the same author, Willem de Bruijn. This also comes with a build
failure when CONFIG_COMPAT is not on, coming in the last patch of
this series.
6) SYNPROXY crashes with conntrack entries that are created via
ctnetlink, more specifically via conntrackd state sync. Patch from
Eric Leblond.
7) RCU safe iteration on set element dumping in nf_tables, from
Liping Zhang.
8) Missing sanitization of immediate date for the bitwise and cmp
expressions in nf_tables.
9) Refcounting logic for chain and objects from set elements does not
integrate into the nf_tables 2-phase commit protocol.
10) Missing sanitization of target verdict in ebtables arpreply target,
from Gao Feng.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This bit was introduced with commit 5a21232983 ("net: Support for
csum_bad in skbuff") to reduce the stack workload when processing RX
packets carrying a wrong Internet Checksum. Up to now, only one driver and
GRO core are setting it.
Suggested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it is allowed to set the default pvid of a bridge to a value
above VLAN_VID_MASK (0xfff). This patch adds a check to br_validate and
returns -EINVAL in case the pvid is out of bounds.
Reproduce by calling:
[root@test ~]# ip l a type bridge
[root@test ~]# ip l a type dummy
[root@test ~]# ip l s bridge0 type bridge vlan_filtering 1
[root@test ~]# ip l s bridge0 type bridge vlan_default_pvid 9999
[root@test ~]# ip l s dummy0 master bridge0
[root@test ~]# bridge vlan
port vlan ids
bridge0 9999 PVID Egress Untagged
dummy0 9999 PVID Egress Untagged
Fixes: 0f963b7592 ("bridge: netlink: add support for default_pvid")
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Tobias Jungel <tobias.jungel@bisdn.de>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The info->target comes from userspace and it would be used directly.
So we need to add the sanity check to make sure it is a valid standard
target, although the ebtables tool has already checked it. Kernel needs
to validate anything coming from userspace.
If the target is set as an evil value, it would break the ebtables
and cause a panic. Because the non-standard target is treated as one
offset.
Now add one helper function ebt_invalid_target, and we would replace
the macro INVALID_TARGET later.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When looking up an iptables rule, the iptables binary compares the
aligned match and target data (XT_ALIGN). In some cases this can
exceed the actual data size to include padding bytes.
Before commit f77bc5b23f ("iptables: use match, target and data
copy_to_user helpers") the malloc()ed bytes were overwritten by the
kernel with kzalloced contents, zeroing the padding and making the
comparison succeed. After this patch, the kernel copies and clears
only data, leaving the padding bytes undefined.
Extend the clear operation from data size to aligned data size to
include the padding bytes, if any.
Padding bytes can be observed in both match and target, and the bug
triggered, by issuing a rule with match icmp and target ACCEPT:
iptables -t mangle -A INPUT -i lo -p icmp --icmp-type 1 -j ACCEPT
iptables -t mangle -D INPUT -i lo -p icmp --icmp-type 1 -j ACCEPT
Fixes: f77bc5b23f ("iptables: use match, target and data copy_to_user helpers")
Reported-by: Paul Moore <pmoore@redhat.com>
Reported-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The attribute sizes for IFLA_BRPORT_MCAST_FLOOD and
IFLA_BRPORT_BCAST_FLOOD weren't accounted for in br_port_info_size()
when they were added. Do so now and also add the corresponding policy
entries:
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Mike Manning <mmanning@brocade.com>
Fixes: b6cb5ac833 ("net: bridge: add per-port multicast flood flag")
Fixes: 99f906e9ad ("bridge: add per-port broadcast flood flag")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS/OVS fixes for net
The following patchset contains a rather large batch of Netfilter, IPVS
and OVS fixes for your net tree. This includes fixes for ctnetlink, the
userspace conntrack helper infrastructure, conntrack OVS support,
ebtables DNAT target, several leaks in error path among other. More
specifically, they are:
1) Fix reference count leak in the CT target error path, from Gao Feng.
2) Remove conntrack entry clashing with a matching expectation, patch
from Jarno Rajahalme.
3) Fix bogus EEXIST when registering two different userspace helpers,
from Liping Zhang.
4) Don't leak dummy elements in the new bitmap set type in nf_tables,
from Liping Zhang.
5) Get rid of module autoload from conntrack update path in ctnetlink,
we don't need autoload at this late stage and it is happening with
rcu read lock held which is not good. From Liping Zhang.
6) Fix deadlock due to double-acquire of the expect_lock from conntrack
update path, this fixes a bug that was introduced when the central
spinlock got removed. Again from Liping Zhang.
7) Safe ct->status update from ctnetlink path, from Liping. The expect_lock
protection that was selected when the central spinlock was removed was
not really protecting anything at all.
8) Protect sequence adjustment under ct->lock.
9) Missing socket match with IPv6, from Peter Tirsek.
10) Adjust skb->pkt_type of DNAT'ed frames from ebtables, from
Linus Luessing.
11) Don't give up on evaluating the expression on new entries added via
dynset expression in nf_tables, from Liping Zhang.
12) Use skb_checksum() when mangling icmpv6 in IPv6 NAT as this deals
with non-linear skbuffs.
13) Don't allow IPv6 service in IPVS if no IPv6 support is available,
from Paolo Abeni.
14) Missing mutex release in error path of xt_find_table_lock(), from
Dan Carpenter.
15) Update maintainers files, Netfilter section. Add Florian to the
file, refer to nftables.org and change project status from Supported
to Maintained.
16) Bail out on mismatching extensions in element updates in nf_tables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. A large bunch of code cleanups, simplify the conntrack extension
codebase, get rid of the fake conntrack object, speed up netns by
selective synchronize_net() calls. More specifically, they are:
1) Check for ct->status bit instead of using nfct_nat() from IPVS and
Netfilter codebase, patch from Florian Westphal.
2) Use kcalloc() wherever possible in the IPVS code, from Varsha Rao.
3) Simplify FTP IPVS helper module registration path, from Arushi Singhal.
4) Introduce nft_is_base_chain() helper function.
5) Enforce expectation limit from userspace conntrack helper,
from Gao Feng.
6) Add nf_ct_remove_expect() helper function, from Gao Feng.
7) NAT mangle helper function return boolean, from Gao Feng.
8) ctnetlink_alloc_expect() should only work for conntrack with
helpers, from Gao Feng.
9) Add nfnl_msg_type() helper function to nfnetlink to build the
netlink message type.
10) Get rid of unnecessary cast on void, from simran singhal.
11) Use seq_puts()/seq_putc() instead of seq_printf() where possible,
also from simran singhal.
12) Use list_prev_entry() from nf_tables, from simran signhal.
13) Remove unnecessary & on pointer function in the Netfilter and IPVS
code.
14) Remove obsolete comment on set of rules per CPU in ip6_tables,
no longer true. From Arushi Singhal.
15) Remove duplicated nf_conntrack_l4proto_udplite4, from Gao Feng.
16) Remove unnecessary nested rcu_read_lock() in
__nf_nat_decode_session(). Code running from hooks are already
guaranteed to run under RCU read side.
17) Remove deadcode in nf_tables_getobj(), from Aaron Conole.
18) Remove double assignment in nf_ct_l4proto_pernet_unregister_one(),
also from Aaron.
19) Get rid of unsed __ip_set_get_netlink(), from Aaron Conole.
20) Don't propagate NF_DROP error to userspace via ctnetlink in
__nf_nat_alloc_null_binding() function, from Gao Feng.
21) Revisit nf_ct_deliver_cached_events() to remove unnecessary checks,
from Gao Feng.
22) Kill the fake untracked conntrack objects, use ctinfo instead to
annotate a conntrack object is untracked, from Florian Westphal.
23) Remove nf_ct_is_untracked(), now obsolete since we have no
conntrack template anymore, from Florian.
24) Add event mask support to nft_ct, also from Florian.
25) Move nf_conn_help structure to
include/net/netfilter/nf_conntrack_helper.h.
26) Add a fixed 32 bytes scratchpad area for conntrack helpers.
Thus, we don't deal with variable conntrack extensions anymore.
Make sure userspace conntrack helper doesn't go over that size.
Remove variable size ct extension infrastructure now this code
got no more clients. From Florian Westphal.
27) Restore offset and length of nf_ct_ext structure to 8 bytes now
that wraparound is not possible any longer, also from Florian.
28) Allow to get rid of unassured flows under stress in conntrack,
this applies to DCCP, SCTP and TCP protocols, from Florian.
29) Shrink size of nf_conntrack_ecache structure, from Florian.
30) Use TCP_MAX_WSCALE instead of hardcoded 14 in TCP tracker,
from Gao Feng.
31) Register SYNPROXY hooks on demand, from Florian Westphal.
32) Use pernet hook whenever possible, instead of global hook
registration, from Florian Westphal.
33) Pass hook structure to ebt_register_table() to consolidate some
infrastructure code, from Florian Westphal.
34) Use consume_skb() and return NF_STOLEN, instead of NF_DROP in the
SYNPROXY code, to make sure device stats are not fooled, patch
from Gao Feng.
35) Remove NF_CT_EXT_F_PREALLOC this kills quite some code that we
don't need anymore if we just select a fixed size instead of
expensive runtime time calculation of this. From Florian.
36) Constify nf_ct_extend_register() and nf_ct_extend_unregister(),
from Florian.
37) Simplify nf_ct_ext_add(), this kills nf_ct_ext_create(), from
Florian.
38) Attach NAT extension on-demand from masquerade and pptp helper
path, from Florian.
39) Get rid of useless ip_vs_set_state_timeout(), from Aaron Conole.
40) Speed up netns by selective calls of synchronize_net(), from
Florian Westphal.
41) Silence stack size warning gcc in 32-bit arch in snmp helper,
from Florian.
42) Inconditionally call nf_ct_ext_destroy(), even if we have no
extensions, to deal with the NF_NAT_MANIP_SRC case. Patch from
Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7e26bf45e4 ("net: bridge: allow SW learn to take over HW fdb
entries") added the ability to "take over an entry which was previously
learned via HW when it shows up from a SW port".
However, if an entry was learned via HW and then a control packet
(e.g., ARP request) was trapped to the CPU, the bridge driver will
update the entry and remove the externally learned flag, although the
entry is still present in HW. Instead, only clear the externally learned
flag in case of roaming.
Fixes: 7e26bf45e4 ("net: bridge: allow SW learn to take over HW fdb entries")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Arkadi Sharashevsky <arkadis@mellanox.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for l2 multicast flood control was added in commit b6cb5ac833
("net: bridge: add per-port multicast flood flag"). It allows broadcast
as it was introduced specifically for unknown multicast flood control.
But as broadcast is a special case of multicast, this may also need to
be disabled. For this purpose, introduce a flag to disable the flooding
of received l2 broadcasts. This approach is backwards compatible and
provides flexibility in filtering for the desired packet types.
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Mike Manning <mmanning@brocade.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to ip_register_table, pass nf_hook_ops to ebt_register_table().
This allows to handle hook registration also via pernet_ops and allows
us to avoid use of legacy register_hook api.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
During removing a bridge device, if the bridge is still up, a new mdb entry
still can be added in br_multicast_add_group() after all mdb entries are
removed in br_multicast_dev_del(). Like the path:
mld_ifc_timer_expire ->
mld_sendpack -> ...
br_multicast_rcv ->
br_multicast_add_group
The new mp's timer will be set up. If the timer expires after the bridge
is freed, it may cause use-after-free panic in br_multicast_group_expired.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
IP: [<ffffffffa07ed2c8>] br_multicast_group_expired+0x28/0xb0 [bridge]
Call Trace:
<IRQ>
[<ffffffff81094536>] call_timer_fn+0x36/0x110
[<ffffffffa07ed2a0>] ? br_mdb_free+0x30/0x30 [bridge]
[<ffffffff81096967>] run_timer_softirq+0x237/0x340
[<ffffffff8108dcbf>] __do_softirq+0xef/0x280
[<ffffffff8169889c>] call_softirq+0x1c/0x30
[<ffffffff8102c275>] do_softirq+0x65/0xa0
[<ffffffff8108e055>] irq_exit+0x115/0x120
[<ffffffff81699515>] smp_apic_timer_interrupt+0x45/0x60
[<ffffffff81697a5d>] apic_timer_interrupt+0x6d/0x80
Nikolay also found it would cause a memory leak - the mdb hash is
reallocated and not freed due to the mdb rehash.
unreferenced object 0xffff8800540ba800 (size 2048):
backtrace:
[<ffffffff816e2287>] kmemleak_alloc+0x67/0xc0
[<ffffffff81260bea>] __kmalloc+0x1ba/0x3e0
[<ffffffffa05c60ee>] br_mdb_rehash+0x5e/0x340 [bridge]
[<ffffffffa05c74af>] br_multicast_new_group+0x43f/0x6e0 [bridge]
[<ffffffffa05c7aa3>] br_multicast_add_group+0x203/0x260 [bridge]
[<ffffffffa05ca4b5>] br_multicast_rcv+0x945/0x11d0 [bridge]
[<ffffffffa05b6b10>] br_dev_xmit+0x180/0x470 [bridge]
[<ffffffff815c781b>] dev_hard_start_xmit+0xbb/0x3d0
[<ffffffff815c8743>] __dev_queue_xmit+0xb13/0xc10
[<ffffffff815c8850>] dev_queue_xmit+0x10/0x20
[<ffffffffa02f8d7a>] ip6_finish_output2+0x5ca/0xac0 [ipv6]
[<ffffffffa02fbfc6>] ip6_finish_output+0x126/0x2c0 [ipv6]
[<ffffffffa02fc245>] ip6_output+0xe5/0x390 [ipv6]
[<ffffffffa032b92c>] NF_HOOK.constprop.44+0x6c/0x240 [ipv6]
[<ffffffffa032bd16>] mld_sendpack+0x216/0x3e0 [ipv6]
[<ffffffffa032d5eb>] mld_ifc_timer_expire+0x18b/0x2b0 [ipv6]
This could happen when ip link remove a bridge or destroy a netns with a
bridge device inside.
With Nikolay's suggestion, this patch is to clean up bridge multicast in
ndo_uninit after bridge dev is shutdown, instead of br_dev_delete, so
that netif_running check in br_multicast_add_group can avoid this issue.
v1->v2:
- fix this issue by moving br_multicast_dev_del to ndo_uninit, instead
of calling dev_close in br_dev_delete.
(NOTE: Depends upon b6fe0440c6 ("bridge: implement missing ndo_uninit()"))
Fixes: e10177abf8 ("bridge: multicast: fix handling of temp and perm entries")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to redirect bridged frames to the bridge device itself or
a bridge port (brouting) via the dnat target then this currently fails:
The ethernet destination of the frame is dnat'ed to the MAC address of
the bridge device or port just fine. However, the IP code drops it in
the beginning of ip_input.c/ip_rcv() as the dnat target left
the skb->pkt_type as PACKET_OTHERHOST.
Fixing this by resetting skb->pkt_type to an appropriate type after
dnat'ing.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add netlink_ext_ack arg to rtnl_doit_func. Pass extack arg to nlmsg_parse
for doit functions that call it directly.
This is the first step to using extended error reporting in rtnetlink.
>From here individual subsystems can be updated to set netlink_ext_ack as
needed.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently we added support for SW fdbs to take over HW ones, but that
results in changing a user-visible fdb flag thus we need to send a
notification, also it's consistent with how HW takes over SW entries.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were simply overlapping changes. In the net/ipv4/route.c
case the code had simply moved around a little bit and the same fix
was made in both 'net' and 'net-next'.
In the net/sched/sch_generic.c case a fix in 'net' happened at
the same time that a new argument was added to qdisc_hash_add().
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter reported a kernel oops when executing the following command:
$ ip link add name test type bridge vlan_default_pvid 1
[13634.939408] BUG: unable to handle kernel NULL pointer dereference at
0000000000000190
[13634.939436] IP: __vlan_add+0x73/0x5f0
[...]
[13634.939783] Call Trace:
[13634.939791] ? pcpu_next_unpop+0x3b/0x50
[13634.939801] ? pcpu_alloc+0x3d2/0x680
[13634.939810] ? br_vlan_add+0x135/0x1b0
[13634.939820] ? __br_vlan_set_default_pvid.part.28+0x204/0x2b0
[13634.939834] ? br_changelink+0x120/0x4e0
[13634.939844] ? br_dev_newlink+0x50/0x70
[13634.939854] ? rtnl_newlink+0x5f5/0x8a0
[13634.939864] ? rtnl_newlink+0x176/0x8a0
[13634.939874] ? mem_cgroup_commit_charge+0x7c/0x4e0
[13634.939886] ? rtnetlink_rcv_msg+0xe1/0x220
[13634.939896] ? lookup_fast+0x52/0x370
[13634.939905] ? rtnl_newlink+0x8a0/0x8a0
[13634.939915] ? netlink_rcv_skb+0xa1/0xc0
[13634.939925] ? rtnetlink_rcv+0x24/0x30
[13634.939934] ? netlink_unicast+0x177/0x220
[13634.939944] ? netlink_sendmsg+0x2fe/0x3b0
[13634.939954] ? _copy_from_user+0x39/0x40
[13634.939964] ? sock_sendmsg+0x30/0x40
[13634.940159] ? ___sys_sendmsg+0x29d/0x2b0
[13634.940326] ? __alloc_pages_nodemask+0xdf/0x230
[13634.940478] ? mem_cgroup_commit_charge+0x7c/0x4e0
[13634.940592] ? mem_cgroup_try_charge+0x76/0x1a0
[13634.940701] ? __handle_mm_fault+0xdb9/0x10b0
[13634.940809] ? __sys_sendmsg+0x51/0x90
[13634.940917] ? entry_SYSCALL_64_fastpath+0x1e/0xad
The problem is that the bridge's VLAN group is created after setting the
default PVID, when registering the netdevice and executing its
ndo_init().
Fix this by changing the order of both operations, so that
br_changelink() is only processed after the netdevice is registered,
when the VLAN group is already initialized.
Fixes: b6677449df ("bridge: netlink: call br_changelink() during br_dev_newlink()")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Peter V. Saveliev <peter@svinota.eu>
Tested-by: Peter V. Saveliev <peter@svinota.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the bridge driver implements an ndo_init(), it was missing a
symmetric ndo_uninit(), causing the different de-initialization
operations to be scattered around its dellink() and destructor().
Implement a symmetric ndo_uninit() and remove the overlapping operations
from its dellink() and destructor().
This is a prerequisite for the next patch, as it allows us to have a
proper cleanup upon changelink() failure during the bridge's newlink().
Fixes: b6677449df ("bridge: netlink: call br_changelink() during br_dev_newlink()")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove & from function pointers to conform to the style found elsewhere
in the file. Done using the following semantic patch
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Arushi Singhal <arushisinghal19971997@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Unnecessary parantheses are also remove.
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NTF_EXT_LEARNED flag was added for switchdev and externally learned
entries, but it can also be used for entries learned via a software
in user-space which requires dynamic entries that do not expire.
One such case that we have is with quagga and evpn which need dynamic
entries but also require to age them themselves.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to take over an entry which was previously learned via HW when it
shows up from a SW port. This is analogous to how HW takes over SW learned
entries already.
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmmii.c
drivers/net/hyperv/netvsc.c
kernel/bpf/hashtab.c
Almost entirely overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your
net-next tree. A couple of new features for nf_tables, and unsorted
cleanups and incremental updates for the Netfilter tree. More
specifically, they are:
1) Allow to check for TCP option presence via nft_exthdr, patch
from Phil Sutter.
2) Add symmetric hash support to nft_hash, from Laura Garcia Liebana.
3) Use pr_cont() in ebt_log, from Joe Perches.
4) Remove some dead code in arp_tables reported via static analysis
tool, from Colin Ian King.
5) Consolidate nf_tables expression validation, from Liping Zhang.
6) Consolidate set lookup via nft_set_lookup().
7) Remove unnecessary rcu read lock side in bridge netfilter, from
Florian Westphal.
8) Remove unused variable in nf_reject_ipv4, from Tahee Yoo.
9) Pass nft_ctx struct to object initialization indirections, from
Florian Westphal.
10) Add code to integrate conntrack helper into nf_tables, also from
Florian.
11) Allow to check if interface index or name exists via
NFTA_FIB_F_PRESENT, from Phil Sutter.
12) Simplify resolve_normal_ct(), from Florian.
13) Use per-limit spinlock in nft_limit and xt_limit, from Liping Zhang.
14) Use rwlock in nft_set_rbtree set, also from Liping Zhang.
15) One patch to remove a useless printk at netns init path in ipvs,
and several patches to document IPVS knobs.
16) Use refcount_t for reference counter in the Netfilter/IPVS code,
from Elena Reshetova.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrei reported a false alarm of lockdep at net/bridge/br_fdb.c:109,
this is because in Andrei's case, a spin_bug() was already triggered
before this, therefore the debug_locks is turned off, lockdep_is_held()
is no longer accurate after that. We should use lockdep_assert_held_once()
instead of lockdep_is_held() to respect debug_locks.
Fixes: 410b3d48f5 ("bridge: fdb: add proper lock checks in searching functions")
Reported-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree, a
rather large batch of fixes targeted to nf_tables, conntrack and bridge
netfilter. More specifically, they are:
1) Don't track fragmented packets if the socket option IP_NODEFRAG is set.
From Florian Westphal.
2) SCTP protocol tracker assumes that ICMP error messages contain the
checksum field, what results in packet drops. From Ying Xue.
3) Fix inconsistent handling of AH traffic from nf_tables.
4) Fix new bitmap set representation with big endian. Fix mismatches in
nf_tables due to incorrect big endian handling too. Both patches
from Liping Zhang.
5) Bridge netfilter doesn't honor maximum fragment size field, cap to
largest fragment seen. From Florian Westphal.
6) Fake conntrack entry needs to be aligned to 8 bytes since the 3 LSB
bits are now used to store the ctinfo. From Steven Rostedt.
7) Fix element comments with the bitmap set type. Revert the flush
field in the nft_set_iter structure, not required anymore after
fixing up element comments.
8) Missing error on invalid conntrack direction from nft_ct, also from
Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas reports kernel oops during rmmod of the br_netfilter module.
Hannes debugged the oops down to a NULL rt6info->rt6i_indev.
Problem is that br_netfilter has the nasty concept of adding a fake
rtable to skb->dst; this happens in a br_netfilter prerouting hook.
A second hook (in bridge LOCAL_IN) is supposed to remove these again
before the skb is handed up the stack.
However, on module unload hooks get unregistered which means an
skb could traverse the prerouting hook that attaches the fake_rtable,
while the 'fake rtable remove' hook gets removed from the hooklist
immediately after.
Fixes: 34666d467c ("netfilter: bridge: move br_netfilter out of the core")
Reported-by: Andreas Karis <akaris@redhat.com>
Debugged-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
consider a bridge with mtu 9000, but end host sending smaller
packets to another host with mtu < 9000.
In this case, after reassembly, bridge+defrag would refragment,
and then attempt to send the reassembled packet as long as it
was below 9k.
Instead we have to cap by the largest fragment size seen.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
as comment says, the function is always called with rcu read lock held.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When we want to validate the expr's dependency or hooks, we must do two
things to accomplish it. First, write a X_validate callback function
and point ->validate to it. Second, call X_validate in init routine.
This is very common, such as fib, nat, reject expr and so on ...
It is a little ugly, since we will call X_validate in the expr's init
routine, it's better to do it in nf_tables_newexpr. So we can avoid to
do this again and again. After doing this, the second step listed above
is not useful anymore, remove them now.
Patch was tested by nftables/tests/py/nft-test.py and
nftables/tests/shell/run-tests.sh.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Logging output was changed when simple printks without KERN_CONT
are now emitted on a new line and KERN_CONT is required to continue
lines so use pr_cont.
Miscellanea:
o realign arguments
o use print_hex_dump instead of a local variant
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
1) Fix double-free in batman-adv, from Sven Eckelmann.
2) Fix packet stats for fast-RX path, from Joannes Berg.
3) Netfilter's ip_route_me_harder() doesn't handle request sockets
properly, fix from Florian Westphal.
4) Fix sendmsg deadlock in rxrpc, from David Howells.
5) Add missing RCU locking to transport hashtable scan, from Xin Long.
6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.
7) Fix race in NAPI handling between poll handlers and busy polling,
from Eric Dumazet.
8) TX path in vxlan and geneve need proper RCU locking, from Jakub
Kicinski.
9) SYN processing in DCCP and TCP need to disable BH, from Eric
Dumazet.
10) Properly handle net_enable_timestamp() being invoked from IRQ
context, also from Eric Dumazet.
11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.
12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
Melo.
13) Fix use-after-free in netvsc driver, from Dexuan Cui.
14) Fix max MTU setting in bonding driver, from WANG Cong.
15) xen-netback hash table can be allocated from softirq context, so use
GFP_ATOMIC. From Anoob Soman.
16) Fix MAC address change bug in bgmac driver, from Hari Vyas.
17) strparser needs to destroy strp_wq on module exit, from WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
strparser: destroy workqueue on module exit
sfc: fix IPID endianness in TSOv2
sfc: avoid max() in array size
rds: remove unnecessary returned value check
rxrpc: Fix potential NULL-pointer exception
nfp: correct DMA direction in XDP DMA sync
nfp: don't tell FW about the reserved buffer space
net: ethernet: bgmac: mac address change bug
net: ethernet: bgmac: init sequence bug
xen-netback: don't vfree() queues under spinlock
xen-netback: keep a local pointer for vif in backend_disconnect()
netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
netfilter: nf_conntrack_sip: fix wrong memory initialisation
can: flexcan: fix typo in comment
can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
can: gs_usb: fix coding style
can: gs_usb: Don't use stack memory for USB transfers
ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
ixgbe: update the rss key on h/w, when ethtool ask for it
...
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Even with multicast flooding turned off, IPv6 ND should still work so
that IPv6 connectivity is provided. Allow this by continuing to flood
multicast traffic originated by us.
Fixes: b6cb5ac833 ("net: bridge: add per-port multicast flood flag")
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Mike Manning <mmanning@brocade.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix error path order in nbp_vlan_init, so if switchdev_port_attr_set
call failes, the vlan_hash wouldn't be destroyed before inited.
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
added_by_external_learn fdb entries are added and expired by
external entities like switchdev driver or external controllers.
ageing is already disabled for such entries. Hence, don't
indicate expiry for such fdb entries.
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can simplify the logic of entries pointing to the bridge by
converging the fdb_delete_by functions, this would allow us to use the
same function for both cases since the fdb's dst is set to NULL if it is
pointing to the bridge thus we can always check for a port match.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid new errors add checks to br_fdb_find and fdb_find_rcu
functions. The first requires hash_lock, the second obviously RCU.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch we had 3 different fdb searching functions which was
confusing. This patch reduces all of them to one - fdb_find_rcu(), and
two flavors: br_fdb_find() which requires hash_lock and br_fdb_find_rcu
which requires RCU. This makes it clear what needs to be used, we also
remove two abusers of __br_fdb_get which called it under hash_lock and
replace them with br_fdb_find().
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload the mc router ports list, whenever it is being changed.
It is done because in some cases mc packets needs to be flooded to all
the ports in this list.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are three places where a port gets deleted from the mc router port
list. This patch join the actual deletion to one function.
It will be helpful for later patch that will offload changes in the mc
router ports list.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload multicast disabled flag, for more accurate mc flood behavior:
When it is on, the mdb should be ignored.
When it is off, unregistered mc packets should be flooded to mc router
ports.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug and cleans up tunnelid range size
calculation code by using consistent variable names
and checks in size calculation and fill functions.
tested for a few cases of vlan-vni range mappings:
(output from patched iproute2):
$bridge vlan showtunnel
port vid tunid
vxlan0 100-105 1000-1005
200 2000
210 2100
211-213 2100-2102
214 2104
216-217 2108-2109
219 2119
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiffies is volatile so read it once.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vtbegin should not be NULL in this function, Its already checked by the
caller.
this should silence the below smatch complaint:
net/bridge/br_netlink_tunnel.c:144 br_fill_vlan_tinfo_range()
error: we previously assumed 'vtbegin' could be null (see line 130)
net/bridge/br_netlink_tunnel.c
129
130 if (vtbegin && vtend && (vtend->vid - vtbegin->vid) > 0) {
^^^^^^^
Check for NULL.
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
Reported-By: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These checks should go after the attributes have been parsed otherwise
we're using tb uninitialized.
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error check on err is redundant as it is being checked
previously each time it has been updated. Remove this redundant
check.
Detected with CoverityScan, CID#140030("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing once per jiffy is enough to limit the bridge's false sharing.
After this change the bridge doesn't show up in the local load HitM stats.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fdb's used and updated fields are written to on every packet forward and
packet receive respectively. Thus if we are receiving packets from a
particular fdb, they'll cause false-sharing with everyone who has looked
it up (even if it didn't match, since mac/vid share cache line!). The
"used" field is even worse since it is updated on every packet forward
to that fdb, thus the standard config where X ports use a single gateway
results in 100% fdb false-sharing. Note that this patch does not prevent
the last scenario, but it makes it better for other bridge participants
which are not using that fdb (and are only doing lookups over it).
The point is with this move we make sure that only communicating parties
get the false-sharing, in a later patch we'll show how to avoid that too.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the fdb garbage collector to a workqueue which fires at least 10
milliseconds apart and cleans chain by chain allowing for other tasks
to run in the meantime. When having thousands of fdbs the system is much
more responsive. Most importantly remove the need to check if the
matched entry has expired in __br_fdb_get that causes false-sharing and
is completely unnecessary if we cleanup entries, at worst we'll get 10ms
of traffic for that entry before it gets deleted.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move around net_bridge so the vlan fields are in the beginning since
they're checked on every packet even if vlan filtering is disabled.
For the port move flags & vlan group to the beginning, so they're in the
same cache line with the port's state (both flags and state are checked
on each packet).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 18bfb924f0 ("net: introduce default neigh_construct/destroy
ndo calls for L2 upper devices") we added these ndos to stacked devices
such as team and bond, so that calls will be propagated to mlxsw.
However, previous commit removed the reliance on these ndos and no new
users of these ndos have appeared since above mentioned commit. We can
therefore safely remove this dead code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, they are:
1) Stash ctinfo 3-bit field into pointer to nf_conntrack object from
sk_buff so we only access one single cacheline in the conntrack
hotpath. Patchset from Florian Westphal.
2) Don't leak pointer to internal structures when exporting x_tables
ruleset back to userspace, from Willem DeBruijn. This includes new
helper functions to copy data to userspace such as xt_data_to_user()
as well as conversions of our ip_tables, ip6_tables and arp_tables
clients to use it. Not surprinsingly, ebtables requires an ad-hoc
update. There is also a new field in x_tables extensions to indicate
the amount of bytes that we copy to userspace.
3) Add nf_log_all_netns sysctl: This new knob allows you to enable
logging via nf_log infrastructure for all existing netnamespaces.
Given the effort to provide pernet syslog has been discontinued,
let's provide a way to restore logging using netfilter kernel logging
facilities in trusted environments. Patch from Michal Kubecek.
4) Validate SCTP checksum from conntrack helper, from Davide Caratti.
5) Merge UDPlite conntrack and NAT helpers into UDP, this was mostly
a copy&paste from the original helper, from Florian Westphal.
6) Reset netfilter state when duplicating packets, also from Florian.
7) Remove unnecessary check for broadcast in IPv6 in pkttype match and
nft_meta, from Liping Zhang.
8) Add missing code to deal with loopback packets from nft_meta when
used by the netdev family, also from Liping.
9) Several cleanups on nf_tables, one to remove unnecessary check from
the netlink control plane path to add table, set and stateful objects
and code consolidation when unregister chain hooks, from Gao Feng.
10) Fix harmless reference counter underflow in IPVS that, however,
results in problems with the introduction of the new refcount_t
type, from David Windsor.
11) Enable LIBCRC32C from nf_ct_sctp instead of nf_nat_sctp,
from Davide Caratti.
12) Missing documentation on nf_tables uapi header, from Liping Zhang.
13) Use rb_entry() helper in xt_connlimit, from Geliang Tang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- ingress hook:
- if port is a tunnel port, use tunnel info in
attached dst_metadata to map it to a local vlan
- egress hook:
- if port is a tunnel port, use tunnel info attached to
vlan to set dst_metadata on the skb
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to attach per vlan tunnel info dst
metadata. This enables bridge driver to map vlan to tunnel_info
at ingress and egress. It uses the kernel dst_metadata infrastructure.
The initial use case is vlan to vni bridging, but the api is generic
to extend to any tunnel_info in the future:
- Uapi to configure/unconfigure/dump per vlan tunnel data
- netlink functions to configure vlan and tunnel_info mapping
- Introduces bridge port flag BR_LWT_VLAN to enable attach/detach
dst_metadata to bridged packets on ports. off by default.
- changes to existing code is mainly refactor some existing vlan
handling netlink code + hooks for new vlan tunnel code
- I have kept the vlan tunnel code isolated in separate files.
- most of the netlink vlan tunnel code is handling of vlan-tunid
ranges (follows the vlan range handling code). To conserve space
vlan-tunid by default are always dumped in ranges if applicable.
Use case:
example use for this is a vxlan bridging gateway or vtep
which maps vlans to vn-segments (or vnis).
iproute2 example (patched and pruned iproute2 output to just show
relevant fdb entries):
example shows same host mac learnt on two vni's and
vlan 100 maps to vni 1000, vlan 101 maps to vni 1001
before (netdev per vni):
$bridge fdb show | grep "00:02:00:00:00:03"
00:02:00:00:00:03 dev vxlan1001 vlan 101 master bridge
00:02:00:00:00:03 dev vxlan1001 dst 12.0.0.8 self
00:02:00:00:00:03 dev vxlan1000 vlan 100 master bridge
00:02:00:00:00:03 dev vxlan1000 dst 12.0.0.8 self
after this patch with collect metdata in bridged mode (single netdev):
$bridge fdb show | grep "00:02:00:00:00:03"
00:02:00:00:00:03 dev vxlan0 vlan 101 master bridge
00:02:00:00:00:03 dev vxlan0 src_vni 1001 dst 12.0.0.8 self
00:02:00:00:00:03 dev vxlan0 vlan 100 master bridge
00:02:00:00:00:03 dev vxlan0 src_vni 1000 dst 12.0.0.8 self
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 69b34fb996 ("netfilter: xt_LOG: add net namespace support for
xt_LOG") disabled logging packets using the LOG target from non-init
namespaces. The motivation was to prevent containers from flooding
kernel log of the host. The plan was to keep it that way until syslog
namespace implementation allows containers to log in a safe way.
However, the work on syslog namespace seems to have hit a dead end
somewhere in 2013 and there are users who want to use xt_LOG in all
network namespaces. This patch allows to do so by setting
/proc/sys/net/netfilter/nf_log_all_netns
to a nonzero value. This sysctl is only accessible from init_net so that
one cannot switch the behaviour from inside a container.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The only caller of this new function is inside of an #ifdef checking
for CONFIG_BRIDGE_IGMP_SNOOPING, so we should move the implementation
there too, in order to avoid this harmless warning:
net/bridge/br_forward.c:177:13: error: 'maybe_deliver_addr' defined but not used [-Werror=unused-function]
Fixes: 6db6f0eae6 ("bridge: multicast to unicast")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements an optional, per bridge port flag and feature to deliver
multicast packets to any host on the according port via unicast
individually. This is done by copying the packet per host and
changing the multicast destination MAC to a unicast one accordingly.
multicast-to-unicast works on top of the multicast snooping feature of
the bridge. Which means unicast copies are only delivered to hosts which
are interested in it and signalized this via IGMP/MLD reports
previously.
This feature is intended for interface types which have a more reliable
and/or efficient way to deliver unicast packets than broadcast ones
(e.g. wifi).
However, it should only be enabled on interfaces where no IGMPv2/MLDv1
report suppression takes place. This feature is disabled by default.
The initial patch and idea is from Felix Fietkau.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[linus.luessing@c0d3.blue: various bug + style fixes, commit message]
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any bridge options specified during link creation (e.g. ip link add)
are ignored as br_dev_newlink() does not process them.
Use br_changelink() to do it.
Fixes: 1332351617 ("bridge: implement rtnl_link_ops->changelink")
Signed-off-by: Ivan Vecera <cera@cera.cz>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed type of csum field in struct igmpv3_query from __be16 to
__sum16 to eliminate type warning, made same change in struct
igmpv3_report for consistency.
Fixed up an ntohs() where htons() should have been used instead.
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In matches and targets that define a kernel-only tail to their
xt_match and xt_target data structs, add a field .usersize that
specifies up to where data is to be shared with userspace.
Performed a search for comment "Used internally by the kernel" to find
relevant matches and targets. Manually inspected the structs to derive
a valid offsetof.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Convert ebtables to copying entries, matches and targets one by one.
The solution is analogous to that of generic xt_(match|target)_to_user
helpers, but is applied to different structs.
Convert existing helpers ebt_make_XXXname helpers that overwrite
fields of an already copy_to_user'd struct with ebt_XXX_to_user
helpers that copy all relevant fields of the struct from scratch.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains accumulated Netfilter fixes for your
net tree:
1) Ensure quota dump and reset happens iff we can deliver numbers to
userspace.
2) Silence splat on incorrect use of smp_processor_id() from nft_queue.
3) Fix an out-of-bound access reported by KASAN in
nf_tables_rule_destroy(), patch from Florian Westphal.
4) Fix layer 4 checksum mangling in the nf_tables payload expression
with IPv6.
5) Fix a race in the CLUSTERIP target from control plane path when two
threads run to add a new configuration object. Serialize invocations
of clusterip_config_init() using spin_lock. From Xin Long.
6) Call br_nf_pre_routing_finish_bridge_finish() once we are done with
the br_nf_pre_routing_finish() hook. From Artur Molchanov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem:
br_nf_pre_routing_finish() calls itself instead of
br_nf_pre_routing_finish_bridge(). Due to this bug reverse path filter drops
packets that go through bridge interface.
User impact:
Local docker containers with bridge network can not communicate with each
other.
Fixes: c5136b15ea ("netfilter: bridge: add and use br_nf_hook_thresh")
Signed-off-by: Artur Molchanov <artur.molchanov@synesis.ru>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
802.1D [1] specifies that the bridges must use a short value to age out
dynamic entries in the Filtering Database for a period, once a topology
change has been communicated by the root bridge.
Add a bridge_ageing_time member in the net_bridge structure to store the
bridge ageing time value configured by the user (ioctl/netlink/sysfs).
If we are using in-kernel STP, shorten the ageing time value to twice
the forward delay used by the topology when the topology change flag is
set. When the flag is cleared, restore the configured ageing time.
[1] "8.3.5 Notifying topology changes ",
http://profesores.elo.utfsm.cl/~agv/elo309/doc/802.1D-1998.pdf
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a __br_set_topology_change helper to set the topology change value.
This can be later extended to add actions when the topology change flag
is set or cleared.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME switchdev attr is actually set
when initializing a bridge port, and when configuring the bridge ageing
time from ioctl/netlink/sysfs.
Add a __set_ageing_time helper to offload the ageing time to physical
switches, and add the SWITCHDEV_F_DEFER flag since it can be called
under bridge lock.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
