Expose the auxiliary clock data so it can be read from the vDSO.
Architectures not using the generic vDSO time framework,
namely SPARC64, are not supported.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250701-vdso-auxclock-v1-11-df7d9f87b9b8@linutronix.de
The upcoming auxiliary clocks need this hook, too.
To separate the architecture hooks from the timekeeper internals, refactor
the hook to only operate on a single vDSO clock.
While at it, use a more robust #define for the hook override.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250701-vdso-auxclock-v1-3-df7d9f87b9b8@linutronix.de
The logic to configure a 'struct vdso_clock' from a
'struct tk_read_base' is copied two times.
Split it into a shared function to reduce the duplication,
especially as another user will be added for auxiliary clocks.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250701-vdso-auxclock-v1-2-df7d9f87b9b8@linutronix.de
Lei Chen raised an issue with CLOCK_MONOTONIC_COARSE seeing time
inconsistencies. Lei tracked down that this was being caused by the
adjustment:
tk->tkr_mono.xtime_nsec -= offset;
which is made to compensate for the unaccumulated cycles in offset when the
multiplicator is adjusted forward, so that the non-_COARSE clockids don't
see inconsistencies.
However, the _COARSE clockid getter functions use the adjusted xtime_nsec
value directly and do not compensate the negative offset via the
clocksource delta multiplied with the new multiplicator. In that case the
caller can observe time going backwards in consecutive calls.
By design, this negative adjustment should be fine, because the logic run
from timekeeping_adjust() is done after it accumulated approximately
multiplicator * interval_cycles
into xtime_nsec. The accumulated value is always larger then the
mult_adj * offset
value, which is subtracted from xtime_nsec. Both operations are done
together under the tk_core.lock, so the net change to xtime_nsec is always
always be positive.
However, do_adjtimex() calls into timekeeping_advance() as well, to
apply the NTP frequency adjustment immediately. In this case,
timekeeping_advance() does not return early when the offset is smaller
then interval_cycles. In that case there is no time accumulated into
xtime_nsec. But the subsequent call into timekeeping_adjust(), which
modifies the multiplicator, subtracts from xtime_nsec to correct for the
new multiplicator.
Here because there was no accumulation, xtime_nsec becomes smaller than
before, which opens a window up to the next accumulation, where the
_COARSE clockid getters, which don't compensate for the offset, can
observe the inconsistency.
This has been tried to be fixed by forwarding the timekeeper in the case
that adjtimex() adjusts the multiplier, which resets the offset to zero:
757b000f7b ("timekeeping: Fix possible inconsistencies in _COARSE clockids")
That works correctly, but unfortunately causes a regression on the
adjtimex() side. There are two issues:
1) The forwarding of the base time moves the update out of the original
period and establishes a new one.
2) The clearing of the accumulated NTP error is changing the behaviour as
well.
User-space expects that multiplier/frequency updates are in effect, when the
syscall returns, so delaying the update to the next tick is not solving the
problem either.
Commit 757b000f7b was reverted so that the established expectations of
user space implementations (ntpd, chronyd) are restored, but that obviously
brought the inconsistencies back.
One of the initial approaches to fix this was to establish a separate
storage for the coarse time getter nanoseconds part by calculating it from
the offset. That was dropped on the floor because not having yet another
state to maintain was simpler. But given the result of the above exercise,
this solution turns out to be the right one. Bring it back in a slightly
modified form.
Thus introduce timekeeper::coarse_nsec and store that nanoseconds part in
it, switch the time getter functions and the VDSO update to use that value.
coarse_nsec is set on operations which forward or initialize the timekeeper
and after time was accumulated during a tick. If there is no accumulation
the timestamp is unchanged.
This leaves the adjtimex() behaviour unmodified and prevents coarse time
from going backwards.
[ jstultz: Simplified the coarse_nsec calculation and kept behavior so
coarse clockids aren't adjusted on each inter-tick adjtimex
call, slightly reworked the comments and commit message ]
Fixes: da15cfdae0 ("time: Introduce CLOCK_REALTIME_COARSE")
Reported-by: Lei Chen <lei.chen@smartx.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <jstultz@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/all/20250419054706.2319105-1-jstultz@google.com
Closes: https://lore.kernel.org/lkml/20250310030004.3705801-1-lei.chen@smartx.com/
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be an array of VDSO clocks.
Now that all preparatory changes are in place:
Split the clock related struct members into a separate struct
vdso_clock. Make sure all users are aware, that vdso_time_data is no longer
initialized as an array and vdso_clock is now the array inside
vdso_data. Remove the vdso_clock define, which mapped it to vdso_time_data
for the transition.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-19-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be array of VDSO clocks. At the moment,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
To prepare for the rework of the data structures, replace the struct
vdso_time_data pointer with a struct vdso_clock pointer where applicable.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-12-c1b5c69a166f@linutronix.de
All users of the time releated parts of the vDSO are now using the generic
storage implementation. Remove the therefore unnecessary compatibility
accessor functions and symbols.
Co-developed-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250204-vdso-store-rng-v3-18-13a4669dfc8c@linutronix.de
Historically each architecture defined their own way to store the vDSO
data page. Add a generic mechanism to provide storage for that page.
Furthermore this generic storage will be extended to also provide
uniform storage for *non*-time-related data, like the random state or
architecture-specific data. These will have their own pages and data
structures, so rename 'vdso_data' into 'vdso_time_data' to make that
split clear from the name.
Also introduce a new consistent naming scheme for the symbols related to
the vDSO, which makes it clear if the symbol is accessible from
userspace or kernel space and the type of data behind the symbol.
The generic fault handler contains an optimization to prefault the vvar
page when the timens page is accessed. This was lifted from s390 and x86.
Co-developed-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250204-vdso-store-rng-v3-5-13a4669dfc8c@linutronix.de
- The final step to get rid of auto-rearming posix-timers
posix-timers are currently auto-rearmed by the kernel when the signal
of the timer is ignored so that the timer signal can be delivered once
the corresponding signal is unignored.
This requires to throttle the timer to prevent a DoS by small intervals
and keeps the system pointlessly out of low power states for no value.
This is a long standing non-trivial problem due to the lock order of
posix-timer lock and the sighand lock along with life time issues as
the timer and the sigqueue have different life time rules.
Cure this by:
* Embedding the sigqueue into the timer struct to have the same life
time rules. Aside of that this also avoids the lookup of the timer
in the signal delivery and rearm path as it's just a always valid
container_of() now.
* Queuing ignored timer signals onto a seperate ignored list.
* Moving queued timer signals onto the ignored list when the signal is
switched to SIG_IGN before it could be delivered.
* Walking the ignored list when SIG_IGN is lifted and requeue the
signals to the actual signal lists. This allows the signal delivery
code to rearm the timer.
This also required to consolidate the signal delivery rules so they are
consistent across all situations. With that all self test scenarios
finally succeed.
- Core infrastructure for VFS multigrain timestamping
This is required to allow the kernel to use coarse grained time stamps
by default and switch to fine grained time stamps when inode attributes
are actively observed via getattr().
These changes have been provided to the VFS tree as well, so that the
VFS specific infrastructure could be built on top.
- Cleanup and consolidation of the sleep() infrastructure
* Move all sleep and timeout functions into one file
* Rework udelay() and ndelay() into proper documented inline functions
and replace the hardcoded magic numbers by proper defines.
* Rework the fsleep() implementation to take the reality of the timer
wheel granularity on different HZ values into account. Right now the
boundaries are hard coded time ranges which fail to provide the
requested accuracy on different HZ settings.
* Update documentation for all sleep/timeout related functions and fix
up stale documentation links all over the place
* Fixup a few usage sites
- Rework of timekeeping and adjtimex(2) to prepare for multiple PTP clocks
A system can have multiple PTP clocks which are participating in
seperate and independent PTP clock domains. So far the kernel only
considers the PTP clock which is based on CLOCK TAI relevant as that's
the clock which drives the timekeeping adjustments via the various user
space daemons through adjtimex(2).
The non TAI based clock domains are accessible via the file descriptor
based posix clocks, but their usability is very limited. They can't be
accessed fast as they always go all the way out to the hardware and
they cannot be utilized in the kernel itself.
As Time Sensitive Networking (TSN) gains traction it is required to
provide fast user and kernel space access to these clocks.
The approach taken is to utilize the timekeeping and adjtimex(2)
infrastructure to provide this access in a similar way how the kernel
provides access to clock MONOTONIC, REALTIME etc.
Instead of creating a duplicated infrastructure this rework converts
timekeeping and adjtimex(2) into generic functionality which operates
on pointers to data structures instead of using static variables.
This allows to provide time accessors and adjtimex(2) functionality for
the independent PTP clocks in a subsequent step.
- Consolidate hrtimer initialization
hrtimers are set up by initializing the data structure and then
seperately setting the callback function for historical reasons.
That's an extra unnecessary step and makes Rust support less straight
forward than it should be.
Provide a new set of hrtimer_setup*() functions and convert the core
code and a few usage sites of the less frequently used interfaces over.
The bulk of the htimer_init() to hrtimer_setup() conversion is already
prepared and scheduled for the next merge window.
- Drivers:
* Ensure that the global timekeeping clocksource is utilizing the
cluster 0 timer on MIPS multi-cluster systems.
Otherwise CPUs on different clusters use their cluster specific
clocksource which is not guaranteed to be synchronized with other
clusters.
* Mostly boring cleanups, fixes, improvements and code movement
-----BEGIN PGP SIGNATURE-----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=2VC6
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2024-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"A rather large update for timekeeping and timers:
- The final step to get rid of auto-rearming posix-timers
posix-timers are currently auto-rearmed by the kernel when the
signal of the timer is ignored so that the timer signal can be
delivered once the corresponding signal is unignored.
This requires to throttle the timer to prevent a DoS by small
intervals and keeps the system pointlessly out of low power states
for no value. This is a long standing non-trivial problem due to
the lock order of posix-timer lock and the sighand lock along with
life time issues as the timer and the sigqueue have different life
time rules.
Cure this by:
- Embedding the sigqueue into the timer struct to have the same
life time rules. Aside of that this also avoids the lookup of
the timer in the signal delivery and rearm path as it's just a
always valid container_of() now.
- Queuing ignored timer signals onto a seperate ignored list.
- Moving queued timer signals onto the ignored list when the
signal is switched to SIG_IGN before it could be delivered.
- Walking the ignored list when SIG_IGN is lifted and requeue the
signals to the actual signal lists. This allows the signal
delivery code to rearm the timer.
This also required to consolidate the signal delivery rules so they
are consistent across all situations. With that all self test
scenarios finally succeed.
- Core infrastructure for VFS multigrain timestamping
This is required to allow the kernel to use coarse grained time
stamps by default and switch to fine grained time stamps when inode
attributes are actively observed via getattr().
These changes have been provided to the VFS tree as well, so that
the VFS specific infrastructure could be built on top.
- Cleanup and consolidation of the sleep() infrastructure
- Move all sleep and timeout functions into one file
- Rework udelay() and ndelay() into proper documented inline
functions and replace the hardcoded magic numbers by proper
defines.
- Rework the fsleep() implementation to take the reality of the
timer wheel granularity on different HZ values into account.
Right now the boundaries are hard coded time ranges which fail
to provide the requested accuracy on different HZ settings.
- Update documentation for all sleep/timeout related functions
and fix up stale documentation links all over the place
- Fixup a few usage sites
- Rework of timekeeping and adjtimex(2) to prepare for multiple PTP
clocks
A system can have multiple PTP clocks which are participating in
seperate and independent PTP clock domains. So far the kernel only
considers the PTP clock which is based on CLOCK TAI relevant as
that's the clock which drives the timekeeping adjustments via the
various user space daemons through adjtimex(2).
The non TAI based clock domains are accessible via the file
descriptor based posix clocks, but their usability is very limited.
They can't be accessed fast as they always go all the way out to
the hardware and they cannot be utilized in the kernel itself.
As Time Sensitive Networking (TSN) gains traction it is required to
provide fast user and kernel space access to these clocks.
The approach taken is to utilize the timekeeping and adjtimex(2)
infrastructure to provide this access in a similar way how the
kernel provides access to clock MONOTONIC, REALTIME etc.
Instead of creating a duplicated infrastructure this rework
converts timekeeping and adjtimex(2) into generic functionality
which operates on pointers to data structures instead of using
static variables.
This allows to provide time accessors and adjtimex(2) functionality
for the independent PTP clocks in a subsequent step.
- Consolidate hrtimer initialization
hrtimers are set up by initializing the data structure and then
seperately setting the callback function for historical reasons.
That's an extra unnecessary step and makes Rust support less
straight forward than it should be.
Provide a new set of hrtimer_setup*() functions and convert the
core code and a few usage sites of the less frequently used
interfaces over.
The bulk of the htimer_init() to hrtimer_setup() conversion is
already prepared and scheduled for the next merge window.
- Drivers:
- Ensure that the global timekeeping clocksource is utilizing the
cluster 0 timer on MIPS multi-cluster systems.
Otherwise CPUs on different clusters use their cluster specific
clocksource which is not guaranteed to be synchronized with
other clusters.
- Mostly boring cleanups, fixes, improvements and code movement"
* tag 'timers-core-2024-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (140 commits)
posix-timers: Fix spurious warning on double enqueue versus do_exit()
clocksource/drivers/arm_arch_timer: Use of_property_present() for non-boolean properties
clocksource/drivers/gpx: Remove redundant casts
clocksource/drivers/timer-ti-dm: Fix child node refcount handling
dt-bindings: timer: actions,owl-timer: convert to YAML
clocksource/drivers/ralink: Add Ralink System Tick Counter driver
clocksource/drivers/mips-gic-timer: Always use cluster 0 counter as clocksource
clocksource/drivers/timer-ti-dm: Don't fail probe if int not found
clocksource/drivers:sp804: Make user selectable
clocksource/drivers/dw_apb: Remove unused dw_apb_clockevent functions
hrtimers: Delete hrtimer_init_on_stack()
alarmtimer: Switch to use hrtimer_setup() and hrtimer_setup_on_stack()
io_uring: Switch to use hrtimer_setup_on_stack()
sched/idle: Switch to use hrtimer_setup_on_stack()
hrtimers: Delete hrtimer_init_sleeper_on_stack()
wait: Switch to use hrtimer_setup_sleeper_on_stack()
timers: Switch to use hrtimer_setup_sleeper_on_stack()
net: pktgen: Switch to use hrtimer_setup_sleeper_on_stack()
futex: Switch to use hrtimer_setup_sleeper_on_stack()
fs/aio: Switch to use hrtimer_setup_sleeper_on_stack()
...
timekeeper_lock protects updates of timekeeper (tk_core). It is also used
by vdso_update_begin/end() and not only internally by the timekeeper code.
As long as there is only a single timekeeper, this works fine. But when
the timekeeper infrastructure will be reused for per ptp clock timekeepers,
timekeeper_lock needs to be part of tk_core..
Therefore encapuslate locking/unlocking of timekeeper_lock and make the
lock static.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <jstultz@google.com>
Link: https://lore.kernel.org/all/20241009-devel-anna-maria-b4-timers-ptp-timekeeping-v2-8-554456a44a15@linutronix.de
No implementation of this hook uses the passed in timekeeper anymore.
This avoids including a non-VDSO header while building the VDSO, which can
lead to compilation errors.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/all/20241010-vdso-generic-arch_update_vsyscall-v1-1-7fe5a3ea4382@linutronix.de
Add vdso_data::max_cycles in preparation to use it to detect potential
multiplication overflow.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240325064023.2997-7-adrian.hunter@intel.com
Architectures can have the requirement to add additional architecture
specific data to the VDSO data page which needs to be updated independent
of the timekeeper updates.
To protect these updates vs. concurrent readers and a conflicting update
through timekeeping, provide helper functions to make such updates safe.
vdso_update_begin() takes the timekeeper_lock to protect against a
potential update from timekeeper code and increments the VDSO sequence
count to signal data inconsistency to concurrent readers. vdso_update_end()
makes the sequence count even again to signal data consistency and drops
the timekeeper lock.
[ Sven: Add interrupt disable handling to the functions ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200804150124.41692-3-svens@linux.ibm.com
If the current clocksource is not VDSO capable there is no point in
updating the high resolution parts of the VDSO data.
Replace the architecture specific check with a check for a VDSO capable
clocksource and skip the update if there is none.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lkml.kernel.org/r/20200207124403.563379423@linutronix.de
Now that all architectures are converted to use the generic storage the
helpers and conditionals can be removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lkml.kernel.org/r/20200207124403.470699892@linutronix.de
All architectures which use the generic VDSO code have their own storage
for the VDSO clock mode. That's pointless and just requires duplicate code.
Provide generic storage for it. The new Kconfig symbol is intermediate and
will be removed once all architectures are converted over.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lkml.kernel.org/r/20200207124403.028046322@linutronix.de
The low resolution parts of the VDSO, i.e.:
clock_gettime(CLOCK_*_COARSE), clock_getres(), time()
can be used even if there is no VDSO capable clocksource.
But if an architecture opts out of the VDSO data update then this
information becomes stale. This affects ARM when there is no architected
timer available. The lack of update causes userspace to use stale data
forever.
Make the update of the low resolution parts unconditional and only skip
the update of the high resolution parts if the architecture requests it.
Fixes: 44f57d788e ("timekeeping: Provide a generic update_vsyscall() implementation")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200114185946.765577901@linutronix.de
The function name suggests that this is a boolean checking whether the
architecture asks for an update of the VDSO data, but it works the other
way round. To spare further confusion invert the logic.
Fixes: 44f57d788e ("timekeeping: Provide a generic update_vsyscall() implementation")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200114185946.656652824@linutronix.de
The update of the VDSO data is depending on __arch_use_vsyscall() returning
True. This is a leftover from the attempt to map the features of various
architectures 1:1 into generic code.
The usage of __arch_use_vsyscall() in the actual vsyscall implementations
got dropped and replaced by the requirement for the architecture code to
return U64_MAX if the global clocksource is not usable in the VDSO.
But the __arch_use_vsyscall() check in the update code stayed which causes
the VDSO data to be stale or invalid when an architecture actually
implements that function and returns False when the current clocksource is
not usable in the VDSO.
As a consequence the VDSO implementations of clock_getres(), time(),
clock_gettime(CLOCK_.*_COARSE) operate on invalid data and return bogus
information.
Remove the __arch_use_vsyscall() check from the VDSO update function and
update the VDSO data unconditionally.
[ tglx: Massaged changelog and removed the now useless implementations in
asm-generic/ARM64/MIPS ]
Fixes: 44f57d788e ("timekeeping: Provide a generic update_vsyscall() implementation")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1571887709-11447-1-git-send-email-chenhc@lemote.com
The VDSO update for CLOCK_BOOTTIME has a overflow issue as it shifts the
nanoseconds based boot time offset left by the clocksource shift. That
overflows once the boot time offset becomes large enough. As a consequence
CLOCK_BOOTTIME in the VDSO becomes a random number causing applications to
misbehave.
Fix it by storing a timespec64 representation of the offset when boot time
is adjusted and add that to the MONOTONIC base time value in the vdso data
page. Using the timespec64 representation avoids a 64bit division in the
update code.
Fixes: 44f57d788e ("timekeeping: Provide a generic update_vsyscall() implementation")
Reported-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1908221257580.1983@nanos.tec.linutronix.de
On 32-bit x86 when building with clang-9, the 'division' loop gets turned
back into an inefficient division that causes a link error:
kernel/time/vsyscall.o: In function `update_vsyscall':
vsyscall.c:(.text+0xe3): undefined reference to `__udivdi3'
Use the existing __iter_div_u64_rem() function which is used to address the
same issue in other places.
Fixes: 44f57d788e ("timekeeping: Provide a generic update_vsyscall() implementation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lkml.kernel.org/r/20190710130206.1670830-1-arnd@arndb.de
The new generic VDSO library allows to unify the update_vsyscall[_tz]()
implementations.
Provide a generic implementation based on the x86 code and the bindings
which need to be implemented in architecture specific code.
[ tglx: Moved it into kernel/time where it belongs. Removed the pointless
line breaks in the stub functions. Massaged changelog ]
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Shijith Thotton <sthotton@marvell.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Mark Salyzyn <salyzyn@android.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Huw Davies <huw@codeweavers.com>
Link: https://lkml.kernel.org/r/20190621095252.32307-4-vincenzo.frascino@arm.com
