Change the API to select MAC default time stamping instead of the PHY.
Indeed the PHY is closer to the wire therefore theoretically it has less
delay than the MAC timestamping but the reality is different. Due to lower
time stamping clock frequency, latency in the MDIO bus and no PHC hardware
synchronization between different PHY, the PHY PTP is often less precise
than the MAC. The exception is for PHY designed specially for PTP case but
these devices are not very widespread. For not breaking the compatibility I
introduce a default_timestamp flag in phy_device that is set by the phy
driver to know we are using the old API behavior.
The phy_set_timestamp function is called at each call of phy_attach_direct.
In case of MAC driver using phylink this function is called when the
interface is turned up. Then if the interface goes down and up again the
last choice of timestamp will be overwritten by the default choice.
A solution could be to cache the timestamp status but it can bring other
issues. In case of SFP, if we change the module, it doesn't make sense to
blindly re-set the timestamp back to PHY, if the new module has a PHY with
mediocre timestamping capabilities.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHYs hwtstamp callback are still getting the timestamp config from
ifreq and using copy_from/to_user.
Get rid of these functions by using timestamp configuration in parameter.
This also allow to move on to kernel_hwtstamp_config and be similar to
net devices using the new ndo_hwstamp_get/set.
This adds the possibility to manipulate the timestamp configuration
from the kernel which was not possible with the copy_from/to_user.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek reports that a deadlock occurs with the AX88772A PHY used on the
ASIX USB network driver:
asix 1-1.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:003:10] driver [Asix Electronics AX88772A] (irq=POLL)
Asix Electronics AX88772A usb-001:003:10: attached PHY driver(mii_bus:phy_addr=usb-001:003:10, irq=POLL)
asix 1-1.4:1.0 eth0: register 'asix' at usb-12110000.usb-1.4, ASIX AX88772 USB 2.0 Ethernet, a2:99:b6💿11:eb
asix 1-1.4:1.0 eth0: configuring for phy/internal link mode
============================================
WARNING: possible recursive locking detected
6.6.0-rc1-00239-g8da77df649c4-dirty #13949 Not tainted
--------------------------------------------
kworker/3:3/71 is trying to acquire lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_start_aneg+0x1c/0x38
but task is already holding lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_state_machine+0x100/0x2b8
This is because we now consistently call phy_process_state_change()
while holding phydev->lock, but the AX88772A PHY driver then goes on
to call phy_start_aneg() which tries to grab the same lock - causing
deadlock.
Fix this by exporting the unlocked version, and use this in the PHY
driver instead.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: ef113a60d0 ("net: phy: call phy_error_precise() while holding the lock")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1qiEFs-007g7b-Lq@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The PSGMII interface is similar to QSGMII. The main difference
is that the PSGMII interface combines five SGMII lines into a
single link while in QSGMII only four lines are combined.
Similarly to the QSGMII, this interface mode might also needs
special handling within the MAC driver.
It is commonly used by Qualcomm with their QCA807x PHY series and
modern WiSoC-s.
Add definitions for the PHY layer to allow to express this type
of connection between the MAC and PHY.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux LEDs can be requested to perform hardware accelerated blinking
to indicate link, RX, TX etc. Pass the rules for blinking to the PHY
driver, if it implements the ops needed to determine if a given
pattern can be offloaded, to offload it, and what the current offload
is. Additionally implement the op needed to get what device the LED is
for.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20230808210436.838995-3-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 1e2dc14509 ("net: ethtool: Add helpers for reporting test results")
declared but never implemented these function.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230808144610.19096-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/core/dev_ioctl.c (built-in code) will want to call phy_mii_ioctl()
for hardware timestamping purposes. This is not directly possible,
because phy_mii_ioctl() is a symbol provided under CONFIG_PHYLIB.
Do something similar to what was done in DSA in commit 5a17818682
("net: dsa: replace NETDEV_PRE_CHANGE_HWTSTAMP notifier with a stub"),
and arrange some indirect calls to phy_mii_ioctl() through a stub
structure containing function pointers, that's provided by phylib as
built-in even when CONFIG_PHYLIB=m, and which phy_init() populates at
runtime (module insertion).
Note: maybe the ownership of the ethtool_phy_ops singleton is backwards,
and the methods exposed by that should be later merged into phylib_stubs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230801142824.1772134-12-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a separate function to read the BASE-T1 abilities. Some PHYs do not
indicate the availability of the extended BASE-T1 ability register, so
this function must be called separately.
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Dan Carpenter reported a signedness bug in genphy_loopback(). Andrew
reports that:
"It is common to get this wrong in general with PHY drivers. Dan
regularly posts fixes like this soon after a PHY driver patch it
merged. I really wish we could somehow get the compiler to warn when
the result from phy_read() is stored into a unsigned type. It would
save Dan a lot of work."
Let's make phy_read*_poll_timeout() immune to further issues when "val"
is an unsigned type by storing the read function's result in a signed
int as well as "val", and using the signed variable both to check for
an error and for propagating that error to the caller.
The advantage of this method is we don't change where the cast from
the signed return code to the user's variable occurs - so users will
see no change.
Previously Heiner changed phy_read_poll_timeout() to check for an error
before evaluating the user supplied condition, but didn't update
phy_read_mmd_poll_timeout(). Make that change there too.
Link: https://lore.kernel.org/r/d7bb312e-2428-45f6-b9b3-59ba544e8b94@kili.mountain
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1q4kX6-00BNuM-Mx@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When taking a network interface down (or removing a SFP module) after
the PHY has encountered an error, phy_stop() complains incorrectly
that it was called from HALTED state.
The reason this is incorrect is that the network driver will have
called phy_start() when the interface was brought up, and the fact
that the PHY has a problem bears no relationship to the administrative
state of the interface. Taking the interface administratively down
(which calls phy_stop()) is always the right thing to do after a
successful phy_start() call, whether or not the PHY has encountered
an error.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several places which open code comparing PHY IDs. Provide a
couple of helpers to assist with this, using a slightly simpler test
than the original:
- phy_id_compare() compares two arbitary PHY IDs and a mask of the
significant bits in the ID.
- phydev_id_compare() compares the bound phydev with the specified
PHY ID, using the bound driver's mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
6ead9c98ca ("net: fec: remove the xdp_return_frame when lack of tx BDs")
144470c88c ("net: fec: using the standard return codes when xdp xmit errors")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mdio_bus_init() is either used as a local module_init() entry,
or it gets called in phy_device.c. In the former case, there
is no declaration, which causes a warning:
drivers/net/phy/mdio_bus.c:1371:12: error: no previous prototype for 'mdio_bus_init' [-Werror=missing-prototypes]
Remove the #ifdef around the declaration to avoid the warning..
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230516194625.549249-4-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A few PHY drivers are currently attempting to not suspend the PHY when
Wake-on-LAN is enabled, however that code is not currently executing at
all due to an early check in phy_suspend().
This prevents PHY drivers from making an appropriate decisions and put
the hardware into a low power state if desired.
In order to allow the PHY drivers to opt into getting their ->suspend
routine to be called, add a PHY_ALWAYS_CALL_SUSPEND bit which can be
set. A boolean that tracks whether the PHY or the attached MAC has
Wake-on-LAN enabled is also provided for convenience.
If phydev::wol_enabled then the PHY shall not prevent its own
Wake-on-LAN detection logic from working and shall not prevent the
Ethernet MAC from receiving packets for matching.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux LEDs can be requested to perform hardware accelerated
blinking. Pass this to the PHY driver, if it implements the op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux LEDs can be software controlled via the brightness file in /sys.
LED drivers need to implement a brightness_set function which the core
will call. Implement an intermediary in phy_device, which will call
into the phy driver if it implements the necessary function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define common binding parsing for all PHY drivers with LEDs using
phylib. Parse the DT as part of the phy_probe and add LEDs to the
linux LED class infrastructure. For the moment, provide a dummy
brightness function, which will later be replaced with a call into the
PHY driver. This allows testing since the LED core might otherwise
reject an LED whose brightness cannot be set.
Add a dependency on LED_CLASS. It either needs to be built in, or not
enabled, since a modular build can result in linker errors.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fwnode_get_phy_node() does not motify the fwnode structure, so make
the argument const,
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cond sometimes is (val & MASK) what may result in a false positive
if val is a negative errno. We shouldn't evaluate cond if val < 0.
This has no functional impact here, but it's not nice.
Therefore switch order of the checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/6d8274ac-4344-23b4-d9a3-cad4c39517d4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With following patches:
commit 9b01c885be ("net: phy: c22: migrate to genphy_c45_write_eee_adv()")
commit 5827b16812 ("net: phy: c45: migrate to genphy_c45_write_eee_adv()")
we set the advertisement to potentially supported values. This behavior
may introduce new regressions on systems where EEE was disabled by
default (BIOS or boot loader configuration or by other ways.)
At same time, with this patches, we would overwrite EEE advertisement
configuration made over ethtool.
To avoid this issues, we need to cache initial and ethtool advertisement
configuration and store it for later use.
Fixes: 9b01c885be ("net: phy: c22: migrate to genphy_c45_write_eee_adv()")
Fixes: 5827b16812 ("net: phy: c45: migrate to genphy_c45_write_eee_adv()")
Fixes: 022c3f87f8 ("net: phy: add genphy_c45_ethtool_get/set_eee() support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add new genphy_c45_an_config_eee_aneg() function and replace some of
genphy_c45_write_eee_adv() calls. This will be needed by the next patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add replacement for phy_ethtool_get/set_eee() functions.
Current phy_ethtool_get/set_eee() implementation is great and it is
possible to make it even better:
- this functionality is for devices implementing parts of IEEE 802.3
specification beyond Clause 22. The better place for this code is
phy-c45.c
- currently it is able to do read/write operations on PHYs with
different abilities to not existing registers. It is better to
use stored supported_eee abilities to avoid false read/write
operations.
- the eee_active detection will provide wrong results on not supported
link modes. It is better to validate speed/duplex properties against
supported EEE link modes.
- it is able to support only limited amount of link modes. We have more
EEE link modes...
By refactoring this code I address most of this point except of the last
one. Adding additional EEE link modes will need more work.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be needed for genphy_c45_ethtool_get_eee() provided
by next patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic function for EEE abilities defined by IEEE 802.3
specification. For now following registers are supported:
- IEEE 802.3-2018 45.2.3.10 EEE control and capability 1 (Register 3.20)
- IEEE 802.3cg-2019 45.2.1.186b 10BASE-T1L PMA status register
(Register 1.2295)
Since I was not able to find any flag signaling support of these
registers, we should detect link mode abilities first and then based on
these abilities doing EEE link modes detection.
Results of EEE ability detection will be stored into new variable
phydev->supported_eee.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deciding if to probe of PHYs using C45 is now determine by if the bus
provides the C45 read method. This makes probe_capabilities redundant
so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some C22 PHYs do bad things when there are C45 transactions on the
bus. In order to handle this, the bus needs to be scanned first for
C22 at all addresses, and then C45 scanned for all addresses.
The Marvell pxa168 driver scans a specific address on the bus to find
its PHY. This is a C22 only device, so update it to use the c22
helper.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch adds support in phylib to read/write PLCA configuration for
Ethernet PHYs that support the OPEN Alliance "10BASE-T1S PLCA
Management Registers" specifications. These can be found at
https://www.opensig.org/about/specifications/
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the required connection between netlink ethtool and
phylib to resolve PLCA get/set config and get status messages.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the link modes for the IEEE 802.3cg Clause 147 10BASE-T1S
Ethernet PHY. According to the specifications, the 10BASE-T1S supports
Point-To-Point Full-Duplex, Point-To-Point Half-Duplex and/or
Point-To-Multipoint (AKA Multi-Drop) Half-Duplex operations.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring the PLCA Reconciliation Sublayer on
multi-drop PHYs that support IEEE802.3cg-2019 Clause 148 (e.g.,
10BASE-T1S). This patch adds the appropriate netlink interface
to ethtool.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently C22 and C45 transactions are mixed over a combined API calls
which make use of a special bit in the reg address to indicate if a
C45 transaction should be performed. This makes it impossible to know
if the bus driver actually supports C45. Additionally, many C22 only
drivers don't return -EOPNOTSUPP when asked to perform a C45
transaction, they mistaking perform a C22 transaction.
This is the first step to cleanly separate C22 from C45. To maintain
backwards compatibility until all drivers which are capable of
performing C45 are converted to this new API, the helper functions
will fall back to the older API if the new API is not
supported. Eventually this fallback will be removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Until now, it is not possible for a PHY driver to disable interrupts
during runtime. If a driver offers the .config_intr() as well as the
.handle_interrupt() ops, it is eligible for interrupt handling.
Introduce a new flag for the dev_flags property of struct phy_device, which
can be set by PHY driver to skip interrupt setup and fall back to polling
mode.
At the moment, this is used for the MaxLinear PHY which has broken
interrupt handling and there is a need to disable interrupts in some
cases.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Now that phylink no longer calls phy_get_rate_matching with
PHY_INTERFACE_MODE_NA, phys no longer need to support it. Remove the
documentation mandating support.
Fixes: 7642cc28fd ("net: phylink: fix PHY validation with rate adaption")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the external phy used by current mac interface is
managed by another mac interface, it means that this
network port cannot work independently, especially
when the system suspends and resumes, the following
trace may appear, so we should create a device link
between phy dev and mac dev.
WARNING: CPU: 0 PID: 24 at drivers/net/phy/phy.c:983 phy_error+0x20/0x68
Modules linked in:
CPU: 0 PID: 24 Comm: kworker/0:2 Not tainted 6.1.0-rc3-00011-g5aaef24b5c6d-dirty #34
Hardware name: Freescale i.MX6 SoloX (Device Tree)
Workqueue: events_power_efficient phy_state_machine
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x68/0x90
dump_stack_lvl from __warn+0xb4/0x24c
__warn from warn_slowpath_fmt+0x5c/0xd8
warn_slowpath_fmt from phy_error+0x20/0x68
phy_error from phy_state_machine+0x22c/0x23c
phy_state_machine from process_one_work+0x288/0x744
process_one_work from worker_thread+0x3c/0x500
worker_thread from kthread+0xf0/0x114
kthread from ret_from_fork+0x14/0x28
Exception stack(0xf0951fb0 to 0xf0951ff8)
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221130021216.1052230-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous attempt to augment carrier_down (see Link)
was not met with much enthusiasm so let's do the simple
thing of exposing what some devices already maintain.
Add a common ethtool statistic for link going down.
Currently users have to maintain per-driver mapping
to extract the right stat from the vendor-specific ethtool -S
stats. carrier_down does not fit the bill because it counts
a lot of software related false positives.
Add the statistic to the extended link state API to steer
vendors towards implementing all of it.
Implement for bnxt and all Linux-controlled PHYs. mlx5 and (possibly)
enic also have a counter for this but I leave the implementation
to their maintainers.
Link: https://lore.kernel.org/r/20220520004500.2250674-1-kuba@kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20221104190125.684910-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some PHYs can be linked with PSE (Power Sourcing Equipment), so search
for related nodes and attach it to the phydev.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass the supported PHY interface types to phylib if the PHY we are
connecting is inside a SFP, so that the PHY driver can select an
appropriate host configuration mode for their interface according to
the host capabilities.
For example the Marvell 88X3310 PHY inside RollBall SFP modules
defaults to 10gbase-r mode on host's side, and the marvell10g
driver currently does not change this setting. But a host may not
support 10gbase-r. For example Turris Omnia only supports sgmii,
1000base-x and 2500base-x modes. The PHY can be configured to use
those modes, but in order for the PHY driver to do that, it needs
to know which modes are supported.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).
This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.
For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.
802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 1000BASE-KX interface mode. This 1G backplane ethernet as described in
clause 70. Clause 73 autonegotiation is mandatory, and only full duplex
operation is supported.
Although at the PMA level this interface mode is identical to
1000BASE-X, it uses a different form of in-band autonegation. This
justifies a separate interface mode, since the interface mode (along
with the MLO_AN_* autonegotiation mode) sets the type of autonegotiation
which will be used on a link. This results in more than just electrical
differences between the link modes.
With regard to 1000BASE-X, 1000BASE-KX holds a similar position to
SGMII: same signaling, but different autonegotiation. PCS drivers
(which typically handle in-band autonegotiation) may only support
1000BASE-X, and not 1000BASE-KX. Similarly, the phy mode is used to
configure serdes phys with phy_set_mode_ext. Due to the different
electrical standards (SFI or XFI vs Clause 70), they will likely want to
use different configuration. Adding a phy interface mode for
1000BASE-KX helps simplify configuration in these areas.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some phy modes such as QSGMII multiplex several MAC<->PHY links on one
single physical interface. QSGMII used to be the only one supported, but
other modes such as QUSGMII also carry multiple links.
This helper allows getting the number of links that are multiplexed
on a given interface.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QUSGMII mode is a derivative of Cisco's USXGMII standard. This
standard is pretty similar to SGMII, but allows for faster speeds, and
has the build-in bits for Quad and Octa variants (like QSGMII).
The main difference with SGMII/QSGMII is that USXGMII/QUSGMII re-uses
the preamble to carry various information, named 'Extensions'.
As of today, the USXGMII standard only mentions the "PCH" extension,
which is used to convey timestamps, allowing in-band signaling of PTP
timestamps without having to modify the frame itself.
This commit adds support for that mode. When no extension is in use, it
behaves exactly like QSGMII, although it's not compatible with QSGMII.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c
9c5de246c1 ("net: sparx5: mdb add/del handle non-sparx5 devices")
fbb89d02e3 ("net: sparx5: Allow mdb entries to both CPU and ports")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Upon system sleep, mdio_bus_phy_suspend() stops the phy_state_machine(),
but subsequent interrupts may retrigger it:
They may have been left enabled to facilitate wakeup and are not
quiesced until the ->suspend_noirq() phase. Unwanted interrupts may
hence occur between mdio_bus_phy_suspend() and dpm_suspend_noirq(),
as well as between dpm_resume_noirq() and mdio_bus_phy_resume().
Retriggering the phy_state_machine() through an interrupt is not only
undesirable for the reason given in mdio_bus_phy_suspend() (freezing it
midway with phydev->lock held), but also because the PHY may be
inaccessible after it's suspended: Accesses to USB-attached PHYs are
blocked once usb_suspend_both() clears the can_submit flag and PHYs on
PCI network cards may become inaccessible upon suspend as well.
Amend phy_interrupt() to avoid triggering the state machine if the PHY
is suspended. Signal wakeup instead if the attached net_device or its
parent has been configured as a wakeup source. (Those conditions are
identical to mdio_bus_phy_may_suspend().) Postpone handling of the
interrupt until the PHY has resumed.
Before stopping the phy_state_machine() in mdio_bus_phy_suspend(),
wait for a concurrent phy_interrupt() to run to completion. That is
necessary because phy_interrupt() may have checked the PHY's suspend
status before the system sleep transition commenced and it may thus
retrigger the state machine after it was stopped.
Likewise, after re-enabling interrupt handling in mdio_bus_phy_resume(),
wait for a concurrent phy_interrupt() to complete to ensure that
interrupts which it postponed are properly rerun.
The issue was exposed by commit 1ce8b37241 ("usbnet: smsc95xx: Forward
PHY interrupts to PHY driver to avoid polling"), but has existed since
forever.
Fixes: 541cd3ee00 ("phylib: Fix deadlock on resume")
Link: https://lore.kernel.org/netdev/a5315a8a-32c2-962f-f696-de9a26d30091@samsung.com/
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # v2.6.33+
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/b7f386d04e9b5b0e2738f0125743e30676f309ef.1656410895.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dev_err_probe() function is quite useful to avoid boilerplate
related to -EPROBE_DEFER handling. Add a phydev_err_probe() helper to
simplify making use of that from phy drivers which otherwise use the
phydev_* helpers.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Export genphy_c45_baset1_read_status() to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move baset1 specific part of genphy_c45_read_pma() code to
separate function to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move baset1 specific part of genphy_c45_pma_setup_forced() code to
separate function to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is needed because the BASE-T1 uses different registers
for status, control and advertisement to those already
employed in the existing phy-c45 functions.
Where required, genphy_c45 functions will now check whether
the device supports BASE-T1 and use the specific registers
instead: 45.2.7.19 BASE-T1 AN control register,
45.2.7.20 BASE-T1 AN status, 45.2.7.21 BASE-T1 AN
advertisement register, 45.2.7.22 BASE-T1 AN LP Base
Page ability register, 45.2.1.185 BASE-T1 PMA/PMD control
register.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add entry for the 10base-T1L full duplex mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_read_master_slave function allows to configure the master/slave
for gigabit phys only. In order to use this function irrespective of
speed, moved the speed check to the genphy_read_status call.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After following the call tree of phy_set_max_speed(), it became clear
that this function never returns anything but 0, so we can change its
result type to *void* and drop the result checks from the three drivers
that actually bothered to do it...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMII has not been documented in the kernel, but information on this PHY
interface mode has been recently found. Document it, and correct the
recently introduced phylink handling for this interface mode.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1mmfVl-0075nP-14@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for a bitmap for phy interface modes, which includes:
- a macro to declare the interface bitmap
- an inline helper to zero the interface bitmap
- an inline helper to detect an empty interface bitmap
- inline helpers to do a bitwise AND and OR operations on two interface
bitmaps
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic fast retrain auto-negotiation function for C45 PHYs.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add API to read 802.3-c45 IDs so that C22/C45 mixed device can use
C45 APIs without failing ID checks.
Signed-off-by: Xu Liang <lxu@maxlinear.com>
Acked-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 25gbase-r phy interface mode
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract phy_id from compatible string. This will be used by
fwnode_mdiobus_register_phy() to create phy device using the
phy_id.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define fwnode_phy_find_device() to iterate an mdiobus and find the
phy device of the provided phy fwnode. Additionally define
device_phy_find_device() to find phy device of provided device.
Define fwnode_get_phy_node() to get phy_node using named reference.
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define fwnode_mdio_find_device() to get a pointer to the
mdio_device from fwnode passed to the function.
Refactor of_mdio_find_device() to use fwnode_mdio_find_device().
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "reverse RMII" protocol name is a personal invention, derived from
"reverse MII".
Just like MII, RMII is an asymmetric protocol in that a PHY behaves
differently than a MAC. In the case of RMII, for example:
- the 50 MHz clock signals are either driven by the MAC or by an
external oscillator (but never by the PHY).
- the PHY can transmit extra in-band control symbols via RXD[1:0] which
the MAC is supposed to understand, but a PHY isn't.
The "reverse MII" protocol is not standardized either, except for this
web document:
https://www.eetimes.com/reverse-media-independent-interface-revmii-block-architecture/#
In short, it means that the Ethernet controller speaks the 4-bit data
parallel protocol from the perspective of a PHY (it acts like a PHY).
This might mean that it implements clause 22 compatible registers,
although that is optional - the important bit is that its pins can be
connected to an MII MAC and it will 'just work'.
In this discussion thread:
https://lore.kernel.org/netdev/20210201214515.cx6ivvme2tlquge2@skbuf/
we agreed that it would be an abuse of terms to use the "RevMII" name
for anything than the 4-bit parallel MII protocol. But since all the
same concepts can be applied to the 2-bit Reduced MII protocol as well,
here we are introducing a "Reverse RMII" protocol. This means: "behave
like an RMII PHY".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the phydev::dev_flags bit allocation to allow bits 15:0 to
define PHY driver specific behavior, bits 23:16 to be reserved for now,
and bits 31:24 to hold generic PHY driver flags.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210526184617.3105012-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of loopback, in most cases we need to disable autoneg support
and force some speed configuration. Otherwise, depending on currently
active auto negotiated link speed, the loopback may or may not work.
This patch was tested with following PHYs: TJA1102, KSZ8081, KSZ9031,
AT8035, AR9331.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic PMA suspend and resume callback functions for C45 PHYs.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resume callback of the PHY driver is called after the one for the MAC
driver. The PHY driver resume callback calls phy_init_hw(), and this is
potentially problematic if the MAC driver calls phy_start() in its resume
callback. One issue was reported with the fec driver and a KSZ8081 PHY
which seems to become unstable if a soft reset is triggered during aneg.
The new flag allows MAC drivers to indicate that they take care of
suspending/resuming the PHY. Then the MAC PM callbacks can handle
any dependency between MAC and PHY PM.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add generic code to enable C45 PHY loopback into the common phy-c45.c
file. This will allow C45 PHY drivers aceess this by setting
.set_loopback.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flag and helper function to indicate that a PHY device is part of
an SFP module, which is set on attach. This can be used by PHY drivers
to handle SFP-specific quirks or behavior.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some internal PHY's have their events like link change reported by the
MAC interrupt. We have PHY_IGNORE_INTERRUPT to deal with this scenario.
I'm not too happy with this name. We don't ignore interrupts, typically
there is no interrupt exposed at a PHY level. So let's rename it to
PHY_MAC_INTERRUPT. This is in line with phy_mac_interrupt(), which is
called from the MAC interrupt handler to handle PHY events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.
Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.
This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
container_of() macro hides a local variable '__mptr' inside. This
becomes a problem when several container_of() are nested in each
other within single line or plain macros.
As C preprocessor doesn't support generating random variable names,
the sole solution is to avoid defining macros that consist only of
container_of() calls, or they will self-shadow '__mptr' each time:
In file included from ./include/linux/bitmap.h:10,
from drivers/net/phy/phy_device.c:12:
drivers/net/phy/phy_device.c: In function ‘phy_device_release’:
./include/linux/kernel.h:693:8: warning: declaration of ‘__mptr’ shadows a previous local [-Wshadow]
693 | void *__mptr = (void *)(ptr); \
| ^~~~~~
./include/linux/phy.h:647:26: note: in expansion of macro ‘container_of’
647 | #define to_phy_device(d) container_of(to_mdio_device(d), \
| ^~~~~~~~~~~~
./include/linux/mdio.h:52:27: note: in expansion of macro ‘container_of’
52 | #define to_mdio_device(d) container_of(d, struct mdio_device, dev)
| ^~~~~~~~~~~~
./include/linux/phy.h:647:39: note: in expansion of macro ‘to_mdio_device’
647 | #define to_phy_device(d) container_of(to_mdio_device(d), \
| ^~~~~~~~~~~~~~
drivers/net/phy/phy_device.c:217:8: note: in expansion of macro ‘to_phy_device’
217 | kfree(to_phy_device(dev));
| ^~~~~~~~~~~~~
./include/linux/kernel.h:693:8: note: shadowed declaration is here
693 | void *__mptr = (void *)(ptr); \
| ^~~~~~
./include/linux/phy.h:647:26: note: in expansion of macro ‘container_of’
647 | #define to_phy_device(d) container_of(to_mdio_device(d), \
| ^~~~~~~~~~~~
drivers/net/phy/phy_device.c:217:8: note: in expansion of macro ‘to_phy_device’
217 | kfree(to_phy_device(dev));
| ^~~~~~~~~~~~~
As they are declared in header files, these warnings are highly
repetitive and very annoying (along with the one from linux/pci.h).
Convert the related macros from linux/{mdio,phy}.h to static inlines
to avoid self-shadowing and potentially improve bug-catching.
No functional changes implied.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210116161246.67075-1-alobakin@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sparx-5 supports this mode and it is missing in the PHY core.
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kdoc does not like it when multiline comment follows the networking
style of starting right on the first line:
include/linux/phy.h:869: warning: Function parameter or member 'config_intr' not described in 'phy_driver'
Link: https://lore.kernel.org/r/20201215063750.3120976-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all the PHY drivers have been migrated to directly implement
the generic .handle_interrupt() callback for a seamless support of
shared IRQs and all the .config_inter() implementations clear any
pending interrupts, we can safely remove the two callbacks.
With this patch, phylib has a proper support for shared IRQs (and not
just for multi-PHY devices. A PHY driver must implement both the
.handle_interrupt() and .config_intr() callbacks for the IRQs to be
actually used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems there are cases where the interrupts are handled by another
entity (ie an IRQ controller embedded inside the PHY) and do not need
any other interraction from phylib. For this kind of PHYs, like the
RTL8366RB, add the genphy_handle_interrupt_no_ack() function which just
triggers the link state machine.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These functions are currently used by phy_interrupt() to either signal
an error condition or to trigger the link state machine. In an attempt
to actually support shared PHY IRQs, export these two functions so that
the actual PHY drivers can use them.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sphinx 3 now checks for duplicated function declarations:
.../Documentation/networking/kapi:143: ../include/linux/phy.h:163: WARNING: Duplicate C declaration, also defined in 'networking/kapi'.
Declaration is 'unsigned int phy_supported_speeds (struct phy_device *phy, unsigned int *speeds, unsigned int size)'.
.../Documentation/networking/kapi:143: ../include/linux/phy.h:1034: WARNING: Duplicate C declaration, also defined in 'networking/kapi'.
Declaration is 'int phy_read_mmd (struct phy_device *phydev, int devad, u32 regnum)'.
.../Documentation/networking/kapi:143: ../include/linux/phy.h:1076: WARNING: Duplicate C declaration, also defined in 'networking/kapi'.
Declaration is 'int __phy_read_mmd (struct phy_device *phydev, int devad, u32 regnum)'.
.../Documentation/networking/kapi:143: ../include/linux/phy.h:1088: WARNING: Duplicate C declaration, also defined in 'networking/kapi'.
Declaration is 'int phy_write_mmd (struct phy_device *phydev, int devad, u32 regnum, u16 val)'.
.../Documentation/networking/kapi:143: ../include/linux/phy.h:1100: WARNING: Duplicate C declaration, also defined in 'networking/kapi'.
Declaration is 'int __phy_write_mmd (struct phy_device *phydev, int devad, u32 regnum, u16 val)'.
It turns that both the C and the H files have the same
kernel-doc markup for the same functions. Let's drop the
at the header file, keeping the one closer to the code.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/75e9a357f9a716833d2094b04898754876365e68.1603791716.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add kerneldoc for the core PHY data structures, a few inline functions
and exported functions which are not already documented.
v2
Typos
g/phy/PHY/s
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing parameter documentation, or fixup wrong parameter names.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load new "reset-post-delay-us" value from MDIO properties,
and if configured to a greater then zero delay do a
flexible sleeping delay after MDIO bus reset deassert.
This allows devices to exit reset state before start
bus communication.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have moved the PHY ethtool statistics to be dynamically
registered, we no longer need to inline those for ethtool. This used to
be done to avoid cross symbol referencing and allow ethtool to be
decoupled from PHYLIB entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the W=1 warning that symbol 'genphy_c45_driver' was not
declared. Should it be static?
Declare it on the phy header file.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two managed helpers for mdiobus - devm_mdiobus_alloc()
and devm_mdiobus_register(). The idea behind devres is that the release
callback releases whatever resource the devm function allocates. In the
mdiobus case however there's no devres associated with the device by
devm_mdiobus_register(). Instead the release callback for
devm_mdiobus_alloc(): _devm_mdiobus_free() unregisters the device if
it is marked as managed.
This all seems wrong. The managed structure shouldn't need to know or
care about whether it's managed or not - and this is the case now for
struct mii_bus. The devres wrapper should be opaque to the managed
resource.
This changeset makes devm_mdiobus_alloc() and devm_mdiobus_register()
conform to common devres standards: devm_mdiobus_alloc() allocates a
devres structure and registers a callback that will call mdiobus_free().
__devm_mdiobus_register() allocated another devres and registers a
callback that will unregister the bus.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions should only be static inline if they're very short. This
devres helper is already over 10 lines and it will grow soon as we'll
be improving upon its approach. Pull it into mdio_devres.c.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function that will return the index in the array for the
passed in internal delay value. The helper requires the array, size and
delay value.
The helper will then return the index for the exact match or return the
index for the index to the closest smaller value.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We face an issue with rtl8211f, a pin is shared between INTB and PMEB,
and the PHY Register Accessible Interrupt is enabled by default, so
the INTB/PMEB pin is always active in polling mode case.
As Heiner pointed out "I was thinking about calling
phy_disable_interrupts() in phy_init_hw(), to have a defined init
state as we don't know in which state the PHY is if the PHY driver is
loaded. We shouldn't assume that it's the chip power-on defaults, BIOS
or boot loader could have changed this. Or in case of dual-boot
systems the other OS could leave the PHY in whatever state."
Make phy_disable_interrupts() non-static so that it could be used in
phy_init_hw() to have a defined init state.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shared PHYs (PHYs in the same hardware package) may have shared
registers and their drivers would usually need to share information.
There is currently a way to have a shared (part of the) init, by using
phy_package_init_once(). This patch extends the logic to share parts of
the probe to allow sharing the initialization of locks or resources
retrieval.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdiobus_scan logic is currently hardcoded to only
work with c22 devices. This works fairly well in most
cases, but its possible that a c45 device doesn't respond
despite being a standard phy. If the parent hardware
is capable, it makes sense to scan for c22 devices before
falling back to c45.
As we want this to reflect the capabilities of the STA,
lets add a field to the mii_bus structure to represent
the capability. That way devices can opt into the extended
scanning. Existing users should continue to default to c22
only scanning as long as they are zero'ing the structure
before use.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the device_ids[] array to allow all MMD IDs to be read rather
than just the first 8 MMDs, but only read the ID if the MDIO_STAT2
register reports that a device really is present here for these new
devices to maintain compatibility with our current behaviour. Note
that only a limited number of devices have MDIO_STAT2.
88X3310 PHY vendor MMDs do are marked as present in the
devices_in_package, but do not contain IEE 802.3 compatible register
sets in their lower space. This avoids reading incorrect values as MMD
identifiers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have two competing requirements for the devices_in_package field.
We want to use it as a bit array indicating which MMDs are present, but
we also want to know if the Clause 22 registers are present.
Since "devices in package" is a term used in the 802.3 specification,
keep this as the as-specified values read from the PHY, and introduce
a new member "mmds_present" to indicate which MMDs are actually
present in the PHY, derived from the "devices in package" value.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for probing MMDs above 7 for a valid devices-in-package
specifier, but only probe the vendor MMDs for this if they also report
that there the device is present in status register 2. This avoids
issues where the MMD is implemented, but does not provide IEEE 802.3
compliant registers (such as the MV88X3310 PHY.)
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.
If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a recurring pattern throughout some of the PHY code converting
a devad and regnum to our packed clause 45 representation. Rather than
having this scattered around the code, let's put a common translation
function in mdio.h, and provide some register accessors.
Convert the phylib core, phylink, bcm87xx and cortina to use these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function was introduced to allow for different handling of
link up and link down events particularly with regard to the
netif_carrier. The third argument do_carrier allowed the flag to
be left unchanged.
Since then the phylink has introduced an implementation that
completely ignores the third parameter since it never wants to
change the flag and the phylib always sets the third parameter
to true so the flag is always changed.
Therefore the third argument (i.e. do_carrier) is no longer
necessary and can be removed. This also means that the phylib
phy_link_down() function no longer needs its second argument.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY drivers can use these helpers for reporting the results. The
results get translated into netlink attributes which are added to the
pre-allocated skbuf.
v3:
Poison phydev->skb
Return -EMSGSIZE when ethnl_bcastmsg_put() fails
Return valid error code when nla_nest_start() fails
Use u8 for results
Actually put u32 length into message
v4:
s/ENOTSUPP/EOPNOTSUPP/g
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide infrastructure for PHY drivers to report the cable test
results. A netlink skb is associated to the phydev. Helpers will be
added which can add results to this skb. Once the test has finished
the results are sent to user space.
When netlink ethtool is not part of the kernel configuration stubs are
provided. It is also impossible to trigger a cable test, so the error
code returned by the alloc function is of no consequence.
v2:
Include the status complete in the netlink notification message
v4:
Replace -EINVAL with -EMSGSIZE
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some PHYs are not capable of generating interrupts when a cable test
finished. They do however support interrupts for normal operations,
like link up/down. As such, the PHY state machine would normally not
poll the PHY.
Add support for indicating the PHY state machine must poll the PHY
when performing a cable test.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Running a cable test is desruptive to normal operation of the PHY and
can take a 5 to 10 seconds to complete. The RTNL lock cannot be held
for this amount of time, and add a new state to the state machine for
running a cable test.
The driver is expected to implement two functions. The first is used
to start a cable test. Once the test has started, it should return.
The second function is called once per second, or on interrupt to
check if the cable test is complete, and to allow the PHY to report
the status.
v2:
Rename phy_cable_test_abort to phy_abort_cable_test
Return different extack when already running test
Use phy_init_hw() to reset the PHY
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are packages which contain multiple PHY devices, eg. a quad PHY
transceiver. Provide functions to allocate and free shared storage.
Usually, a quad PHY contains global registers, which don't belong to any
PHY. Provide convenience functions to access these registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
we don't need genphy_no_soft_reset() any longer. Not setting
callback soft_reset results in a no-op now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there's no special ordering requirement for mdiobus_unregister(),
then driver code can be simplified by using a device-managed version
of mdiobus_register(). Prerequisite is that bus allocation has been
done device-managed too. Else mdiobus_free() may be called whilst
bus is still registered, resulting in a BUG_ON(). Therefore let
devm_mdiobus_register() return -EPERM if bus was allocated
non-managed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it is sometimes necessary to poll a phy register by phy_read()
function until its value satisfies some condition. introduce
phy_read_poll_timeout() macros that do this.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it is sometimes necessary to poll a phy register by phy_read_mmd()
function until its value satisfies some condition. introduce
phy_read_mmd_poll_timeout() macros that do this.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far PHY drivers have to check whether a downshift occurred to be
able to notify the user. To make life of drivers authors a little bit
easier move the downshift notification to phylib. phy_check_downshift()
compares the highest mutually advertised speed with the actual value
of phydev->speed (typically read by the PHY driver from a
vendor-specific register) to detect a downshift.
v2:
- Add downshift hint to phy_print_status
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add APIs for modifying a MDIO device register, similar to the existing
phy_modify() group of functions, but at mdiobus level instead. Adapt
__phy_modify_changed() to use the new mdiobus level helper.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
did_interrupt() clears the interrupt, therefore handle_interrupt() can
not check which event triggered the interrupt. To overcome this
constraint and allow more flexibility for customer interrupt handlers,
let's decouple handle_interrupt() from parts of the phylib interrupt
handling. Custom interrupt handlers now have to implement the
did_interrupt() functionality in handle_interrupt() if needed.
Fortunately we have just one custom interrupt handler so far (in the
mscc PHY driver), convert it to the changed API.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we have the unfortunate situation that mdio_bus_phy_may_suspend()
is called in suspend AND resume path, assuming that function result is
the same. After the original change this is no longer the case,
resulting in broken resume as reported by Geert.
To fix this call mdio_bus_phy_may_suspend() in the suspend path only,
and let the phy_device store the info whether it was suspended by
MDIO bus PM.
Fixes: 503ba7c696 ("net: phy: Avoid multiple suspends")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On all PHY drivers that implement did_interrupt() reading the interrupt
status bits clears them. This means we may loose an interrupt that
is triggered between calling did_interrupt() and phy_clear_interrupt().
As part of the fix make it a requirement that did_interrupt() clears
the interrupt.
The Fixes tag refers to the first commit where the patch applies
cleanly.
Fixes: 49644e68f4 ("net: phy: add callback for custom interrupt handler to struct phy_driver")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears most ethernet drivers follow one of two main strategies
for mdio bus/phy management. A monolithic model where the net driver
itself creates, probes and uses the phy, and one where an external
mdio/phy driver instantiates the mdio bus/phy and the net driver
only attaches to a known phy. Usually in this latter model the phys
are discovered via DT relationships or simply phy name/address
hardcoding.
This is a shame because modern well behaved mdio buses are self
describing and can be probed. The mdio layer itself is fully capable
of this, yet there isn't a clean way for a standalone net driver
to attach and enumerate the discovered devices. This is because
outside of of_mdio_find_bus() there isn't a straightforward way
to acquire the mii_bus pointer.
So, lets add a mdio_find_bus which can return the mii_bus based
only on its name.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple of helpers to resolve negotiated flow control. Two helpers
are provided:
- linkmode_resolve_pause() which takes the link partner and local
advertisements, and decodes whether we should enable TX or RX pause
at the MAC. This is useful outside of phylib, e.g. in phylink.
- phy_get_pause(), which returns the TX/RX enablement status for the
current negotiation results of the PHY.
This allows us to centralise the flow control resolution, rather than
spreading it around.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new version of phy_do_ioctl that doesn't check whether net_device
is running. It will typically be used if suitable drivers attach the
PHY in probe already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We just added phy_do_ioctl, but it turned out that we need another
version of this function that doesn't check whether net_device is
running. So rename phy_do_ioctl to phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of network drivers has the same glue code to use phy_mii_ioctl
as ndo_do_ioctl handler. So let's add such a generic ndo_do_ioctl
handler to phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We maintain global statistics for an entire MDIO bus, as well as broken
down, per MDIO bus address statistics. Given that it is possible for
MDIO devices such as switches to access MDIO bus addresses for which
there is not a mdio_device instance created (therefore not a a
corresponding device directory in sysfs either), we also maintain
per-address statistics under the statistics folder. The layout looks
like this:
/sys/class/mdio_bus/../statistics/
transfers
errrors
writes
reads
transfers_<addr>
errors_<addr>
writes_<addr>
reads_<addr>
When a mdio_device instance is registered, a statistics/ folder is
created with the tranfers, errors, writes and reads attributes which
point to the appropriate MDIO bus statistics structure.
Statistics are 64-bit unsigned quantities and maintained through the
u64_stats_sync.h helper functions.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a reference to MACsec ops in the phy_device, to allow
PHYs to support offloading MACsec operations. The phydev lock will be
held while calling those helpers.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the macsec_context structure. It will be used
in the kernel to exchange information between the common MACsec
implementation (macsec.c) and the MACsec hardware offloading
implementations. This structure contains pointers to MACsec specific
structures which contain the actual MACsec configuration, and to the
underlying device (phydev for now).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The information about the PHY attached to the PHYLINK instance is useful
but is missing the IRQ prints that phy_attached_info() adds.
phy_attached_info() is a bit long and it would not be possible to use
phylink_info() anyway.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent discussion has revealed that the use of PHY_INTERFACE_MODE_10GKR
is incorrect. Add a 10GBASE-R definition, document both the -R and -KR
versions, and the fact that 10GKR was used incorrectly.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the stack supports time stamping in PHY devices. However,
there are newer, non-PHY devices that can snoop an MII bus and provide
time stamps. In order to support such devices, this patch introduces
a new interface to be used by both PHY and non-PHY devices.
In addition, the one and only user of the old PHY time stamping API is
converted to the new interface.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some parts of the networking stack and at least one driver test fields
within the 'struct phy_device' in order to query time stamping
capabilities and to invoke time stamping methods. This patch adds a
functional interface around the time stamping fields. This will allow
insulating the callers from future changes to the details of the time
stamping implemenation.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY IDs are 32-bit unsigned quantities. Ensure that they are always
treated as such, and not passed around as "int"s.
Fixes: 13d0ab6750 ("net: phy: check return code when requesting PHY driver module")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two drivers and generic code which contain exactly the same
code to read the status of a PHY operating without autonegotiation
enabled. Rather than duplicate this code, provide a helper to read
this information.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for restarting autonegotiation(), similar to the clause 45
variant. Use it in __genphy_config_aneg()
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to make locking/unlocking the MDIO bus easier.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no users of phy_ethtool_sset() in the kernel anymore, and
as of commit 3c1bcc8614 ("net: ethernet: Convert phydev advertize
and supported from u32 to link mode"), the implementation is slightly
buggy - it doesn't correctly check the masked advertising mask as it
used to.
Remove it, and update the phy documentation to refer to its replacement
function.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Add core phylib help for supporting SFP sockets on PHYs. This provides
a mechanism to inform the SFP layer about PHY up/down events, and also
unregister the SFP bus when the PHY is going away.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for clause 37 1000Base-X auto-negotiation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Tao Ren <taoren@fb.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the update of phylib's software pause mode state from
genphy_read_status(), so that we can re-use this functionality with
PHYs that have alternative ways to read the negotiation results.
Tested-by: tinywrkb <tinywrkb@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move reading the link partner advertisement out of genphy_read_status()
into its own separate function. This will allow re-use of this code by
PHY drivers that are able to read the resolved status from the PHY.
Tested-by: tinywrkb <tinywrkb@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 34786005ec ("net: phy: prevent PHYs w/o Clause 22 regs from calling
genphy_config_aneg") introduced a check that aborts phy_config_aneg()
if the phy is a C45 phy.
This causes phy_state_machine() to call phy_error() so that the phy
ends up in PHY_HALTED state.
Instead of returning -EOPNOTSUPP, call genphy_c45_config_aneg()
(analogous to the C22 case) so that the state machine can run
correctly.
genphy_c45_config_aneg() closely resembles mv3310_config_aneg()
in drivers/net/phy/marvell10g.c, excluding vendor specific
configurations for 1000BaseT.
Fixes: 22b56e8270 ("net: phy: replace genphy_10g_driver with genphy_c45_driver")
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all users have been removed we can remove genphy_config_init.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far phy_speed_down/up can be used up to 1Gbps only. Remove this
restriction by using new helper __phy_speed_down. New member adv_old
in struct phy_device is used by phy_speed_up to restore the advertised
modes before calling phy_speed_down. Don't simply advertise what is
supported because a user may have intentionally removed modes from
advertisement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
phy_speed_down_core provides most of the functionality for
phy_speed_down. It makes use of new helper phy_resolve_min_speed that is
based on the sorting of the settings[] array. In certain cases it may be
helpful to be able to exclude legacy half duplex modes, therefore
prepare phy_resolve_min_speed() for it.
v2:
- rename __phy_speed_down to phy_speed_down_core
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Add helper function phy_modify_paged_changed, behavios is the same
as for phy_modify_changed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated PHY in 2.5Gbps chip RTL8125 is the first (known to me)
PHY that uses standard Clause 22 for all modes up to 1Gbps and adds
2.5Gbps control using vendor-specific registers. To use phylib for
the standard part little extensions are needed:
- Move most of genphy_config_aneg to a new function
__genphy_config_aneg that takes a parameter whether restarting
auto-negotiation is needed (depending on whether content of
vendor-specific advertisement register changed).
- Don't clear phydev->lp_advertising in genphy_read_status so that
we can set non-C22 mode flags before.
Basically both changes mimic the behavior of the equivalent Clause 45
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables phy_basic_ports_array, phy_fibre_port_array and
phy_all_ports_features_array are declared static and marked
EXPORT_SYMBOL_GPL(), which is at best an odd combination.
Because the variables were decided to be a part of API, this commit
removes the static attributes and adds the declarations to the header.
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DWMAC4 is capable to support clause 45 mdio communication.
This patch enable the feature on stmmac_mdio_write() and
stmmac_mdio_read() by following phy_write_mmd() and
phy_read_mmd() mdiobus read write implementation format.
Reviewed-by: Li, Yifan <yifan2.li@intel.com>
Signed-off-by: Kweh Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
