Add qpic_common.c file which hold all the common
qpic APIs which will be used by both qpic raw nand
driver and qpic spi nand driver.
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SkyHigh S35ML01G300, S35ML01G301, S35ML02G300, and S35ML04G300 are 1Gb,
2Gb, and 4Gb SLC SPI NAND flash family. This family of devices has
on-die ECC which parity bits are stored to hidden area. In this family
the on-die ECC cannot be disabled so raw access needs to be prevented.
Link: https://www.skyhighmemory.com/download/SPI_S35ML01_04G3_002_19205.pdf?v=P
Co-developed-by: KR Kim <kr.kim@skyhighmemory.com>
Signed-off-by: KR Kim <kr.kim@skyhighmemory.com>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SkyHigh spinand device has ECC enable bit in configuration register but
it must be always enabled. If ECC is disabled, read and write ops
results in undetermined state. For such devices, a way to avoid raw
access is needed.
Introduce SPINAND_NO_RAW_ACCESS flag to advertise the device does not
support raw access. In such devices, the on-die ECC engine ops returns
error to I/O request in raw mode.
Checking and marking BBM need to be cared as special case, by adding
fallback mechanism that tries read/write OOB with ECC enabled.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
misc issues got fixed.
SPI-NAND changes:
A load of fixes to Winbond manufacturer driver have been done, plus a
structure constification.
Raw NAND changes:
The GPMI driver has been improved on the power management side.
The Davinci driver has been cleaned up.
A leak in the Atmel driver plus some typos in the core have been fixed.
SPI NOR changes:
Introduce byte swap support for 8D-8D-8D mode and a user for it:
macronix. SPI NOR flashes may swap the bytes on a 16-bit boundary when
configured in Octal DTR mode. For such cases the byte order is
propagated through SPI MEM to the SPI controllers so that the
controllers swap the bytes back at runtime. This avoids breaking the
boot sequence because of the endianness problems that appear when the
bootloaders use 1-1-1 and the kernel uses 8D-8D-8D with byte swap
support. Along with the SPI MEM byte swap support we queue a patch for
the SPI MXIC controller that swaps the bytes back at runtime.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmc/WusACgkQJWrqGEe9
VoR0Zgf/admMDFN51dtkz950bnOkZfot/4uLgUQCDenhbugHrom7KWQ6+oh1+HSN
9EAjLoLNQzq4vxKx1WoI/99iJO86zg/DiyVD3nQidv9JkqHRDp2t13ZLclr4gGyW
Kh1lDQ+9GwpB8CQQnxVaPL39NjjqR3RiEfEP/1fVgGYQvCt4yedhVsDT3WThJeVb
1n7l54RBpZji88mT0chFB9CoSLnzrYZFh2MvzJaW/i1v02yZLXHFxFiKiKo+WysY
FGQTY3x0j20H2Ib8RSP7ECegvNb1HtfIxAPsTIqDBGbrA+ahvBr0J/XxX3NbV3RT
Ee4rXqL257zH9dC9Rr1LJAZCqiyx7w==
=p+y9
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD device changes:
- switch platform_driver back to remove()
- misc fixes
SPI-NAND changes:
- a load of fixes to Winbond manufacturer driver
- structure constification
Raw NAND changes:
- improve the power management of the GPMI driver
- Davinci driver clean-ups
- fix leak in the Atmel driver
- fix some typos in the core
SPI NOR changes:
- Introduce byte swap support for 8D-8D-8D mode and a user for it:
macronix.
SPI NOR flashes may swap the bytes on a 16-bit boundary when
configured in Octal DTR mode. For such cases the byte order is
propagated through SPI MEM to the SPI controllers so that the
controllers swap the bytes back at runtime. This avoids breaking
the boot sequence because of the endianness problems that appear
when the bootloaders use 1-1-1 and the kernel uses 8D-8D-8D with
byte swap support. Along with the SPI MEM byte swap support we
queue a patch for the SPI MXIC controller that swaps the bytes back
at runtime"
* tag 'mtd/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (25 commits)
mtd: spi-nor: core: replace dummy buswidth from addr to data
mtd: spi-nor: winbond: add "w/ and w/o SFDP" comment
mtd: spi-nor: spansion: Use nor->addr_nbytes in octal DTR mode in RD_ANY_REG_OP
mtd: Switch back to struct platform_driver::remove()
mtd: cfi_cmdset_0002: remove redundant assignment to variable ret
mtd: spinand: Constify struct nand_ecc_engine_ops
MAINTAINERS: add mailing list for GPMI NAND driver
mtd: spinand: winbond: Sort the devices
mtd: spinand: winbond: Ignore the last ID characters
mtd: spinand: winbond: Fix 512GW, 01GW, 01JW and 02JW ECC information
mtd: spinand: winbond: Fix 512GW and 02JW OOB layout
mtd: nand: raw: gpmi: improve power management handling
mtd: nand: raw: gpmi: switch to SYSTEM_SLEEP_PM_OPS
mtd: rawnand: davinci: use generic device property helpers
mtd: rawnand: davinci: break the line correctly
mtd: rawnand: davinci: order headers alphabetically
mtd: rawnand: atmel: Fix possible memory leak
mtd: rawnand: Correct multiple typos in comments
mtd: hyperbus: rpc-if: Add missing MODULE_DEVICE_TABLE
mtd: spi-nor: add support for Macronix Octal flash
...
'struct nand_ecc_engine_ops' are not modified in these drivers.
Constifying this structure moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
Update the prototype of mxic_ecc_get_pipelined_ops() accordingly.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
16709 1374 16 18099 46b3 drivers/mtd/nand/ecc-mxic.o
After:
=====
text data bss dec hex filename
16789 1294 16 18099 46b3 drivers/mtd/nand/ecc-mxic.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/72597e9de2320a4109be2112e696399592edacd4.1729271136.git.christophe.jaillet@wanadoo.fr
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Add two flags for inserting the Plane Select bit into the column
address during the write_to_cache and the read_from_cache operation.
Add the SPINAND_HAS_PROG_PLANE_SELECT_BIT flag for serial NAND flash
that require inserting the Plane Select bit into the column address
during the write_to_cache operation.
Add the SPINAND_HAS_READ_PLANE_SELECT_BIT flag for serial NAND flash
that require inserting the Plane Select bit into the column address
during the read_from_cache operation.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240909092643.2434479-2-linchengming884@gmail.com
This helper function will soon be used from a vendor driver, let's
export it through the spinand.h header. No need for any export, as there
is currently no reason for any module to need it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240826101412.20644-6-miquel.raynal@bootlin.com
A regular page read consist in:
- Asking one page of content from the NAND array to be loaded in the
chip's SRAM,
- Waiting for the operation to be done,
- Retrieving the data (I/O phase) from the chip's SRAM.
When reading several sequential pages, the above operation is repeated
over and over. There is however a way to optimize these accesses, by
enabling continuous reads. The feature requires the NAND chip to have a
second internal SRAM area plus a bit of additional internal logic to
trigger another internal transfer between the NAND array and the second
SRAM area while the I/O phase is ongoing. Once the first I/O phase is
done, the host can continue reading more data, continuously, as the chip
will automatically switch to the second SRAM content (which has already
been loaded) and in turns trigger the next load into the first SRAM area
again.
From an instruction perspective, the command op-codes are different, but
the same cycles are required. The only difference is that after a
continuous read (which is stopped by a CS deassert), the host must
observe a delay of tRST. However, because there is no guarantee in Linux
regarding the actual state of the CS pin after a transfer (in order to
speed-up the next transfer if targeting the same device), it was
necessary to manually end the continuous read with a configuration
register write operation.
Continuous reads have two main drawbacks:
* They only work on full pages (column address ignored)
* Only the main data area is pulled, out-of-band bytes are not
accessible. Said otherwise, the feature can only be useful with on-die
ECC engines.
Performance wise, measures have been performed on a Zynq platform using
Macronix SPI-NAND controller with a Macronix chip (based on the
flash_speed tool modified for testing sequential reads):
- 1-1-1 mode: performances improved from +3% (2-pages) up to +10% after
a dozen pages.
- 1-1-4 mode: performances improved from +15% (2-pages) up to +40% after
a dozen pages.
This series is based on a previous work from Macronix engineer Jaime
Liao.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20240826101412.20644-5-miquel.raynal@bootlin.com
In order to be able to iterate easily across eraseblocks rather than
pages, let's introduce a block iterator inspired from the page iterator.
The main usage of this iterator will be for continuous/sequential reads,
where it is interesting to use a single request rather than split the
requests in smaller chunks (ie. pages) that can be hardly optimized.
So a "continuous" boolean get's added for this purpose.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240826101412.20644-3-miquel.raynal@bootlin.com
Soon a helper for iterating over blocks will be needed (for continuous
read purposes). In order to clarify the intend of this helper, let's
rename it with the "page" wording inside.
While at it, improve the doc and fix a typo.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20240826101412.20644-2-miquel.raynal@bootlin.com
In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240503184230.2927283-1-andriy.shevchenko@linux.intel.com
UBI:
- Add Zhihao Cheng as reviewer
- Attach via device tree
- Add NVMEM layer
- Various fastmap related fixes
UBIFS:
- Add Zhihao Cheng as reviewer
- Convert to folios
- Various fixes (memory leaks in error paths, function prototypes)
-----BEGIN PGP SIGNATURE-----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=70g8
-----END PGP SIGNATURE-----
Merge tag 'ubifs-for-linus-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
"UBI:
- Add Zhihao Cheng as reviewer
- Attach via device tree
- Add NVMEM layer
- Various fastmap related fixes
UBIFS:
- Add Zhihao Cheng as reviewer
- Convert to folios
- Various fixes (memory leaks in error paths, function prototypes)"
* tag 'ubifs-for-linus-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs: (34 commits)
mtd: ubi: fix NVMEM over UBI volumes on 32-bit systems
mtd: ubi: provide NVMEM layer over UBI volumes
mtd: ubi: populate ubi volume fwnode
mtd: ubi: introduce pre-removal notification for UBI volumes
mtd: ubi: attach from device tree
mtd: ubi: block: use notifier to create ubiblock from parameter
dt-bindings: mtd: ubi-volume: allow UBI volumes to provide NVMEM
dt-bindings: mtd: add basic bindings for UBI
ubifs: Queue up space reservation tasks if retrying many times
ubifs: ubifs_symlink: Fix memleak of inode->i_link in error path
ubifs: dbg_check_idx_size: Fix kmemleak if loading znode failed
ubi: Correct the number of PEBs after a volume resize failure
ubi: fix slab-out-of-bounds in ubi_eba_get_ldesc+0xfb/0x130
ubi: correct the calculation of fastmap size
ubifs: Remove unreachable code in dbg_check_ltab_lnum
ubifs: fix function pointer cast warnings
ubifs: fix sort function prototype
ubi: Check for too small LEB size in VTBL code
MAINTAINERS: Add Zhihao Cheng as UBI/UBIFS reviewer
ubifs: Convert populate_page() to take a folio
...
The main series brought is an update of the Broadcom support to support
all BCMBCA SoCs and their specificity (ECC, write protection,
configuration straps), plus a few misc fixes and changes in the main
driver. Device tree updates are also part of this PR, initially because
of a misunderstanding on my side.
The STM32_FMC2 controller driver is also upgraded to properly support
MP1 and MP25 SoCs.
A new compatible is added for an Atmel flavor.
Among all these feature changes, there is as well a load of continuous
read related fixes, avoiding more corner conditions and clarifying the
logic. Finally a few miscellaneous fixes are made to the core, the
lpx32xx_mlc, fsl_lbc, Meson and Atmel controller driver, as well as
final one in the Hynix vendor driver.
SPI-NAND
The ESMT support has been extended to match 5 bytes ID to avoid
collisions. Winbond support on its side receives support for W25N04KV
chips.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmXzgv4ACgkQJWrqGEe9
VoTwUAgAqwzuaAbhMuHABS2IJnn9KZHCo4f2goXhtrtRP2oDSgzsT8Yke2vfJTIx
KBtjWRYdp5n8GRSmDmO1n/oNnKdjkzbOhP0ow8aZqhKYtjQ7O0xxd4gxQu3gCoVz
ypWq3tpMkKH0MyD8d+HulFhldMmyGv5BqXeioLi2azeALCbpgVcGAHaMxUlRB/p3
iM3GtBr9hUbai6HlynnPsiAAmyUc1gvGGHJ8t2ShjaW5LzK7uBqJLhSVizfP8I6g
N6l0C+KKwFmXlprtgMcg/HjW2QWKOyeqrhmgTzcJIHRiPjySnmfOVeHBLu6y+1wl
MC3BC5kHNSmOfuU76/93LUQUwkWvUA==
=TaNQ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.9' into mtd/next
Raw NAND
The main series brought is an update of the Broadcom support to support
all BCMBCA SoCs and their specificity (ECC, write protection,
configuration straps), plus a few misc fixes and changes in the main
driver. Device tree updates are also part of this PR, initially because
of a misunderstanding on my side.
The STM32_FMC2 controller driver is also upgraded to properly support
MP1 and MP25 SoCs.
A new compatible is added for an Atmel flavor.
Among all these feature changes, there is as well a load of continuous
read related fixes, avoiding more corner conditions and clarifying the
logic. Finally a few miscellaneous fixes are made to the core, the
lpx32xx_mlc, fsl_lbc, Meson and Atmel controller driver, as well as
final one in the Hynix vendor driver.
SPI-NAND
The ESMT support has been extended to match 5 bytes ID to avoid
collisions. Winbond support on its side receives support for W25N04KV
chips.
Introduce a new notification type UBI_VOLUME_SHUTDOWN to inform users
that a volume is just about to be removed.
This is needed because users (such as the NVMEM subsystem) expect that
at the time their removal function is called, the parenting device is
still available (for removal of sysfs nodes, for example, in case of
NVMEM which otherwise WARNs on volume removal).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
While reviewing the hyperbus sfdp proposal the following problem was
noticed:
In file included from ./include/linux/mtd/gen_probe.h:10,
from drivers/mtd/hyperbus/hyperbus-sfdp.c:6:
./include/linux/mtd/flashchip.h:77:9: error: unknown type name ‘wait_queue_head_t’
77 | wait_queue_head_t wq; /* Wait on here when we're waiting for the chip
| ^~~~~~~~~~~~~~~~~
It is good practice to directly include all headers used, it avoids
implicit dependencies and spurious breakage if someone rearranges
headers and causes the implicit include to vanish.
Explicitly include <linux/wait.h> in include/linux/mtd/flashchip.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240205100955.149755-1-tudor.ambarus@linaro.org
E.g. ESMT chips will return an identification code with a length of 5
bytes. In order to prevent ambiguity, flash chips would actually need to
return IDs that are up to 17 or more bytes long due to JEDEC's
continuation scheme. I understand that if a manufacturer ID is located
in bank N of JEDEC's database (there are currently 16 banks), N - 1
continuation codes (7Fh) need to be added to the identification code
(comprising of manufacturer ID and device ID). However, most flash chip
manufacturers don't seem to implement this (correctly).
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Tested-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240125200108.24374-2-ezra@easyb.ch
The most meaningful change being the conversion of the brcmnand driver
to the ->exec_op() API, this series brought additional changes to the
core in order to help controller drivers to handle themselves the WP pin
during destructive operations when relevant.
As always, there is as well a whole bunch of miscellaneous W=1 fixes,
together with a few runtime fixes (double free, timeout value, OOB
layout, missing register initialization) and the usual load of remove
callbacks turned into void (which led to switch the txx9ndfmc driver to
use module_platform_driver()).
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmWCs3IACgkQJWrqGEe9
VoTmRAf/XkCofpATQRzhvFFQXZhCNP/EAKnRM2Ubc7rnwscVWNX/0XyvN7wyy185
tYoJf/MuFFwLEsXz05EU+PDQKr3t2QGCRhxL/ATIIVeQUAJtNqrpkg+f0m+PX2+D
upCmhqS+uBpD4X67K59pi4qBtRCDC1uuenZgWF+7oNfJmvHIx9aF5+wgEZGv3TaC
3WZ9kNb+BcM0TuTxQYC/ehHMsN1dF7zpUUVj4cz++ZnBrQIZx2SwROiAb7MUxkLE
9QCsoBhurDGwF7CRULEm92AQ1SdFD3r0fsv+Y3+YVY+YTJCXnYR33qJuoRgqUaz1
y5ZwCRbkB2AOuP1k1cMyo/hqy7rECw==
=nfPx
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.8' into mtd/next
* Raw NAND
The most meaningful change being the conversion of the brcmnand driver
to the ->exec_op() API, this series brought additional changes to the
core in order to help controller drivers to handle themselves the WP pin
during destructive operations when relevant.
As always, there is as well a whole bunch of miscellaneous W=1 fixes,
together with a few runtime fixes (double free, timeout value, OOB
layout, missing register initialization) and the usual load of remove
callbacks turned into void (which led to switch the txx9ndfmc driver to
use module_platform_driver()).
The ONFI specification states that devices do not need to support
sequential reads across LUN boundaries. In order to prevent such event
from happening and possibly failing, let's introduce the concept of
"pause" in the sequential read to handle these cases. The first/last
pages remain the same but any time we cross a LUN boundary we will end
and restart (if relevant) the sequential read operation.
Cc: stable@vger.kernel.org
Fixes: 003fe4b954 ("mtd: rawnand: Support for sequential cache reads")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/linux-mtd/20231215123208.516590-2-miquel.raynal@bootlin.com
Allow NAND controller to be responsible for write protect pin
handling during fast path and exec_op destructive operation
when controller_wp flag is set.
Signed-off-by: David Regan <dregan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231125012438.15191-2-dregan@broadcom.com
Erase and program operations need the write protect (wp) pin to be
de-asserted to take effect. Add the concept of destructive
operation and pass the information to exec_op() so controllers know
when they should de-assert this pin without having to decode
the command opcode.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: David Regan <dregan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231125012438.15191-1-dregan@broadcom.com
remove callbacks to return void. Comes next (in number of changes) Kees'
additional structures annotations to improve the sanitizers. The usual
amount of cleanups apply.
About the more substancial contribution, one main function of the
partitions core could return an error which was not checked, this is now
fixed. On the bindings side, fixed partitions can now have a compression
property. Finally, an erroneous situation is now always avoided in the
MAP RAM driver.
* CFI
A several years old byte swap has been fixed.
* NAND
The subsystem has, as usual, seen a bit of cleanup being done this
cycle, typically return values of platform_get_irq() and
devm_kasprintf(). There is also a better ECC check in the Arasan
driver. This comes with smaller misc changes.
In the SPI-NAND world there is now support for Foresee F35SQA002G,
Winbond W25N and XTX XT26 chips.
* SPI NOR
For SPI NOR we cleaned the flash info entries in order to have
them slimmer and self explanatory. In order to make the entries
as slim as possible, we introduced sane default values so that
the actual flash entries don't need to specify them. We now use
a flexible macro to specify the flash ID instead of the previous
INFOx() macros that had hardcoded ID lengths.
Instead of:
- { "w25q512nwm", INFO(0xef8020, 0, 64 * 1024, 0)
- OTP_INFO(256, 3, 0x1000, 0x1000) },
We now use:
+ .id = SNOR_ID(0xef, 0x80, 0x20),
+ .name = "w25q512nwm",
+ .otp = SNOR_OTP(256, 3, 0x1000, 0x1000),
We also removed some flash entries: the very old Catalyst
SPI EEPROMs that were introduced once with the SPI-NOR subsystem,
and a Fujitsu MRAM. Both should use the at25 EEPROM driver.
The latter even has device tree bindings for the at25 driver.
We made sure that the conversion didn't introduce any unwanted
changes by comparing the .rodata segment before and after the
conversion. The patches landed in linux-next immediately after
v6.6-rc2, we haven't seen any regressions yet.
Apart of the autumn cleaning we introduced a new flash entry,
at25ff321a, and added block protection support for mt25qu512a.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmVGJNgACgkQJWrqGEe9
VoQ5ggf/flUHU7RI02T7HNwkHayq/NOgaGIUkUZEwdfEBd6/8nLzpDeh9UuQCBvO
izOdRSiDDhcav6YsKs+7UKnonY0uZ5VwB3cjRcgWzsI/nyARs5CeV8VJxqxiGYqU
25rZVVVoNr/4eV6kb9Sx0yUTLobidlNKtpv0w0hLFoVu+eb35RzE/MHaYmialM87
W4W/aHxJH/Nsz9hi13FWE4CpbRYbg2hEBsQhaQV/Uvf4htxYZ+H0ItZGMm/Lsjk4
31eCbgH4yOP2DaQi5KRtvZauKMptqWOo+3ymjDGDi7soQe2qRa5BFsH8cz9/2lDk
hxLk/mGKB4jfnkAaOv5dc0CTcYsnuQ==
=V+qH
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"The main set of changes is related to Uwe's work converting platform
remove callbacks to return void. Comes next (in number of changes)
Kees' additional structures annotations to improve the sanitizers. The
usual amount of cleanups apply.
About the more substancial contribution, one main function of the
partitions core could return an error which was not checked, this is
now fixed. On the bindings side, fixed partitions can now have a
compression property. Finally, an erroneous situation is now always
avoided in the MAP RAM driver.
CFI:
- A several years old byte swap has been fixed.
NAND:
- The subsystem has, as usual, seen a bit of cleanup being done this
cycle, typically return values of platform_get_irq() and
devm_kasprintf(). There is also a better ECC check in the Arasan
driver. This comes with smaller misc changes.
- In the SPI-NAND world there is now support for Foresee F35SQA002G,
Winbond W25N and XTX XT26 chips.
SPI NOR:
- For SPI NOR we cleaned the flash info entries in order to have them
slimmer and self explanatory. In order to make the entries as slim
as possible, we introduced sane default values so that the actual
flash entries don't need to specify them. We now use a flexible
macro to specify the flash ID instead of the previous INFOx()
macros that had hardcoded ID lengths.
Instead of:
{ "w25q512nwm", INFO(0xef8020, 0, 64 * 1024, 0)
OTP_INFO(256, 3, 0x1000, 0x1000) },
We now use:
.id = SNOR_ID(0xef, 0x80, 0x20),
.name = "w25q512nwm",
.otp = SNOR_OTP(256, 3, 0x1000, 0x1000),
- We also removed some flash entries: the very old Catalyst SPI
EEPROMs that were introduced once with the SPI-NOR subsystem, and a
Fujitsu MRAM. Both should use the at25 EEPROM driver. The latter
even has device tree bindings for the at25 driver.
- We made sure that the conversion didn't introduce any unwanted
changes by comparing the .rodata segment before and after the
conversion. The patches landed in linux-next immediately after
v6.6-rc2, we haven't seen any regressions yet.
- Apart of the autumn cleaning we introduced a new flash entry,
at25ff321a, and added block protection support for mt25qu512a"
* tag 'mtd/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (91 commits)
mtd: cfi_cmdset_0001: Byte swap OTP info
mtd: rawnand: meson: check return value of devm_kasprintf()
mtd: rawnand: intel: check return value of devm_kasprintf()
mtd: rawnand: sh_flctl: Convert to module_platform_driver()
mtd: spi-nor: micron-st: use SFDP table for mt25qu512a
mtd: spi-nor: micron-st: enable lock/unlock for mt25qu512a
mtd: rawnand: Remove unused of_gpio.h inclusion
mtd: spinand: Add support for XTX XT26xxxDxxxxx
mtd: spinand: winbond: add support for serial NAND flash
mtd: rawnand: cadence: Annotate struct cdns_nand_chip with __counted_by
mtd: rawnand: Annotate struct mtk_nfc_nand_chip with __counted_by
mtd: spinand: add support for FORESEE F35SQA002G
mtd: rawnand: rockchip: Use struct_size()
mtd: rawnand: arasan: Include ECC syndrome along with in-band data while checking for ECC failure
mtd: Use device_get_match_data()
mtd: spi-nor: nxp-spifi: Convert to platform remove callback returning void
mtd: spi-nor: hisi-sfc: Convert to platform remove callback returning void
mtd: maps: sun_uflash: Convert to platform remove callback returning void
mtd: maps: sa1100-flash: Convert to platform remove callback returning void
mtd: maps: pxa2xx-flash: Convert to platform remove callback returning void
...
this cycle, typically return values of platform_get_irq() and
devm_kasprintf(), plus structure annotations for sanitizers. There is
also a better ECC check in the Arasan driver. This comes with smaller
misc changes.
In the SPI-NAND world there is now support for Foresee F35SQA002G,
Winbond W25N and XTX XT26 chips.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmVGIQoACgkQJWrqGEe9
VoTPOggAjxm9yHRE6kQh5QT1mLaU9VMchyl7+/rwxOc4TA3TLIcgACIjz0BDHTSu
+VBB+XzL5pV2Nxn2ixepIyiNsACFgNKJ6+5toQomCEgQSKyNXUghE29G6HZ8Mydr
+/o2GZy7nBoVtgnSjAto3tSwM9T5aE9rovJXp+sXjBkPdmUvH0vQs1EPqiHzlF1w
PBuaQYecODLli6/9Mlt2Los5BRUNzdRaHXFUI9Cr7+u37ZIA0McAtrSbFeEX+A1T
DRB2cPzosHK0IQ+093Rh9KNRPqhPB3KYaEf7/+VjuZxjzbjeeDT8Hhic9PJPcvSz
6CWta2A4g5nxUDArb2ZO9bTkw2es7Q==
=nCq+
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.7' into mtd/next
The raw NAND subsystem has, as usual, seen a bit of cleanup being done
this cycle, typically return values of platform_get_irq() and
devm_kasprintf(), plus structure annotations for sanitizers. There is
also a better ECC check in the Arasan driver. This comes with smaller
misc changes.
In the SPI-NAND world there is now support for Foresee F35SQA002G,
Winbond W25N and XTX XT26 chips.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Both the JEDEC and ONFI specification say that read cache sequential
support is an optional command. This means that we not only need to
check whether the individual controller supports the command, we also
need to check the parameter pages for both ONFI and JEDEC NAND flashes
before enabling sequential cache reads.
This fixes support for NAND flashes which don't support enabling cache
reads, i.e. Samsung K9F4G08U0F or Toshiba TC58NVG0S3HTA00.
Sequential cache reads are now only available for ONFI and JEDEC
devices, if individual vendors implement this, it needs to be enabled
per vendor.
Tested on i.MX6Q with a Samsung NAND flash chip that doesn't support
sequential reads.
Fixes: 003fe4b954 ("mtd: rawnand: Support for sequential cache reads")
Cc: stable@vger.kernel.org
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230922141717.35977-1-r.czerwinski@pengutronix.de
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct cfi_private.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230915201206.never.107-kees@kernel.org
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct lpddr_private.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230915201159.never.112-kees@kernel.org
* Fix -Wvoid-pointer-to-enum-cast warning
* Export 'nand_exit_status_op()'
* dt-bindings: Fix nand-controller.yaml license
Raw NAND controller driver changes:
* Omap, Omap2, Samsung, Atmel, fsl_upm, lpc32xx_slc, lpc32xx_mlc, STM32_FMC2,
sh_ftlctl, MXC, Sunxi:
- Use devm_platform_get_and_ioremap_resource()
* Orion, vf610_nfc, Sunxi, STM32_FMC2, MTK, mpc5121, lpc32xx_slc, Intel,
FSMC, Arasan:
- Use helper function devm_clk_get_optional_enabled()
* Brcmnand:
- Use devm_platform_ioremap_resource_byname()
- Propagate init error -EPROBE_DEFER up
- Propagate error and simplify ternary operators
- Fix mtd oobsize
- Fix potential out-of-bounds access in oob write
- Fix crash during the panic_write
- Fix potential false time out warning
- Fix ECC level field setting for v7.2 controller
* fsmc: Handle clk prepare error in fsmc_nand_resume()
* Marvell: Add support for AC5 SoC
* Meson:
- Support for 512B ECC step size
- Fix build error
- Use NAND core API to check status
- dt-bindings:
* Make ECC properties dependent
* Support for 512B ECC step size
* Drop unneeded quotes
* Oxnas: Remove driver and bindings
* Qcom:
- Conversion to ->exec_op()
- Removal of the legacy interface
- Two full series of improvements/misc fixes
* Use the BIT() macro
* Use u8 instead of uint8_t
* Fix alignment with open parenthesis
* Fix the spacing
* Fix wrong indentation
* Fix a typo
* Early structure initialization
* Fix address parsing within ->exec_op()
* Remove superfluous initialization of "ret"
* Rename variables in qcom_op_cmd_mapping()
* Handle unsupported opcode in qcom_op_cmd_mapping()
* Fix the opcode check in qcom_check_op()
* Use EOPNOTSUPP instead of ENOTSUPP
* Wrap qcom_nand_exec_op() to 80 columns
* Unmap sg_list and free desc within submic_descs()
* Simplify the call to nand_prog_page_end_op()
* Do not override the error no of submit_descs()
* Sort includes alphabetically
* Clear buf_count and buf_start in raw read
* Add read/read_start ops in exec_op path
* vf610_nfc: Do not check 0 for platform_get_irq()
SPI-NAND changes:
* gigadevice: Add support for GD5F1GQ{4,5}RExxH
* esmt: Add support for F50D2G41KA
* toshiba: Add support for T{C,H}58NYG{0,2}S3HBAI4 and TH58NYG3S0HBAI6
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmTsYbAACgkQJWrqGEe9
VoQTsQf+MA+rMfIoyOSLwaFm0Z5UPwIuhleumNgkV2yoC2H42ugz7+Qo4ZS8iHjY
qBUWA/PF4s5snF8A/x4uSEUkdT6etuJ58uKy53304C6cx7RXLtfc7qJfs6fQVLqL
O6uO/EPdUkmiIbdXcRQRiAUDRHEFMPVEHd5pECB0l/qbiNLWQWRFUsmaP6kBZnm1
y7xPfxJo3GuMKJMWnMg+kcoQ7hhIvd0FRztL6VT4SV/et/nfCYjAVXOpViZ8e3+d
tq5yp+WatcBL9tGFSV3IyLW5Z+x1oVDoOIoTk/hWdHsITaHBxXBb8Llc6Eh7GYCD
5mj/renycHEv2Wc2v93z7W3XtnY77Q==
=Pp9B
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.6' into mtd/next
Raw NAND core changes:
* Fix -Wvoid-pointer-to-enum-cast warning
* Export 'nand_exit_status_op()'
* dt-bindings: Fix nand-controller.yaml license
Raw NAND controller driver changes:
* Omap, Omap2, Samsung, Atmel, fsl_upm, lpc32xx_slc, lpc32xx_mlc, STM32_FMC2,
sh_ftlctl, MXC, Sunxi:
- Use devm_platform_get_and_ioremap_resource()
* Orion, vf610_nfc, Sunxi, STM32_FMC2, MTK, mpc5121, lpc32xx_slc, Intel,
FSMC, Arasan:
- Use helper function devm_clk_get_optional_enabled()
* Brcmnand:
- Use devm_platform_ioremap_resource_byname()
- Propagate init error -EPROBE_DEFER up
- Propagate error and simplify ternary operators
- Fix mtd oobsize
- Fix potential out-of-bounds access in oob write
- Fix crash during the panic_write
- Fix potential false time out warning
- Fix ECC level field setting for v7.2 controller
* fsmc: Handle clk prepare error in fsmc_nand_resume()
* Marvell: Add support for AC5 SoC
* Meson:
- Support for 512B ECC step size
- Fix build error
- Use NAND core API to check status
- dt-bindings:
* Make ECC properties dependent
* Support for 512B ECC step size
* Drop unneeded quotes
* Oxnas: Remove driver and bindings
* Qcom:
- Conversion to ->exec_op()
- Removal of the legacy interface
- Two full series of improvements/misc fixes
* Use the BIT() macro
* Use u8 instead of uint8_t
* Fix alignment with open parenthesis
* Fix the spacing
* Fix wrong indentation
* Fix a typo
* Early structure initialization
* Fix address parsing within ->exec_op()
* Remove superfluous initialization of "ret"
* Rename variables in qcom_op_cmd_mapping()
* Handle unsupported opcode in qcom_op_cmd_mapping()
* Fix the opcode check in qcom_check_op()
* Use EOPNOTSUPP instead of ENOTSUPP
* Wrap qcom_nand_exec_op() to 80 columns
* Unmap sg_list and free desc within submic_descs()
* Simplify the call to nand_prog_page_end_op()
* Do not override the error no of submit_descs()
* Sort includes alphabetically
* Clear buf_count and buf_start in raw read
* Add read/read_start ops in exec_op path
* vf610_nfc: Do not check 0 for platform_get_irq()
SPI-NAND changes:
* gigadevice: Add support for GD5F1GQ{4,5}RExxH
* esmt: Add support for F50D2G41KA
* toshiba: Add support for T{C,H}58NYG{0,2}S3HBAI4 and TH58NYG3S0HBAI6
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When underlying device is removed mtd core will crash
in case user space is holding open handle.
Need to use proper refcounting so device is release
only when has no users.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230620131905.648089-2-alexander.usyskin@intel.com
Instead of propagating the fmode_t, just use a bool to track if a mtd
block device was opened for writing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20230608110258.189493-23-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Convert to platform remove callback returning void
* Fix spelling mistake waifunc() -> waitfunc()
Raw NAND controller driver changes:
* imx: Remove unused is_imx51_nfc and imx53_nfc functions
* omap2: Drop obsolete dependency on COMPILE_TEST
* orion: Use devm_platform_ioremap_resource()
* qcom:
- Use of_property_present() for testing DT property presence
- Use devm_platform_get_and_ioremap_resource()
* stm32_fmc2: Depends on ARCH_STM32 instead of MACH_STM32MP157
* tmio: Remove reference to config MTD_NAND_TMIO in the parsers
Raw NAND manufacturer driver changes:
* hynix: Fix up bit 0 of sdr_timing_mode
SPI-NAND changes:
* Add support for ESMT F50x1G41LB
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmRANGgACgkQJWrqGEe9
VoRo+wf9EfUFJA84za9m0c51OBDw+yZBpwnHi8zIJ3Rhf19ALluYgxBqsXkR8sYd
gFT3RUnjHsUypnH6Qi0ZBfSQuuH0/Io76TYW+n9ABWSL7zvupyt6biP8l8Rh016X
Y/0Ftxwa5lUkTrZ4w3DdYnPFsAzxfwRFFVPj4mTGK1c/FG8RbyWtyOO2/J0VI+7M
41IR/HKQoaNNnrt+CmxBxqcRuP/nJvwTg//EXetJHlP7pyL8WXw/qQaQxVPfBGYr
U++MGOKIQgZC+ojPTcnSPLLzeo5jaz0lpLFEkcjYjHI8csSB81cIRkUkjIJs02d/
U8fOctks4ipzhoGzHQ+uRGVZ6pyyTw==
=qHKn
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.4' into mtd/next
Raw NAND core changes:
* Convert to platform remove callback returning void
* Fix spelling mistake waifunc() -> waitfunc()
Raw NAND controller driver changes:
* imx: Remove unused is_imx51_nfc and imx53_nfc functions
* omap2: Drop obsolete dependency on COMPILE_TEST
* orion: Use devm_platform_ioremap_resource()
* qcom:
- Use of_property_present() for testing DT property presence
- Use devm_platform_get_and_ioremap_resource()
* stm32_fmc2: Depends on ARCH_STM32 instead of MACH_STM32MP157
* tmio: Remove reference to config MTD_NAND_TMIO in the parsers
Raw NAND manufacturer driver changes:
* hynix: Fix up bit 0 of sdr_timing_mode
SPI-NAND changes:
* Add support for ESMT F50x1G41LB
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some SPI NOR controllers that used this method were moved to
drivers/spi/. We don't accept new support for the existing SPI NOR
controllers drivers under drivers/mtd/spi-nor/controllers/ and we
encourage their owners to move the drivers under drivers/spi/.
Make spi_nor_restore() private as we're going to use it just in core.c.
Link: https://lore.kernel.org/r/20230331074606.3559258-8-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
On devices featuring several banks, the Read While Write (RWW) feature
is here to improve the overall performance when performing parallel
reads and writes at different locations (different banks). The following
constraints have to be taken into account:
1#: A single operation can be performed in a given bank.
2#: Only a single program or erase operation can happen on the entire
chip (common hardware limitation to limit costs)
3#: Reads must remain serialized even though reads crossing bank
boundaries are allowed.
4#: The I/O bus is unique and thus is the most constrained resource, all
spi-nor operations requiring access to the spi bus (through the spi
controller) must be serialized until the bus exchanges are over. So
we must ensure a single operation can be "sent" at a time.
5#: Any other operation that would not be either a read or a write or an
erase is considered requiring access to the full chip and cannot be
parallelized, we then need to ensure the full chip is in the idle
state when this occurs.
All these constraints can easily be managed with a proper locking model:
1#: Is enforced by a bitfield of the in-use banks, so that only a single
operation can happen in a specific bank at any time.
2#: Is handled by the ongoing_pe boolean which is set before any write
or erase, and is released only at the very end of the
operation. This way, no other destructive operation on the chip can
start during this time frame.
3#: An ongoing_rd boolean allows to track the ongoing reads, so that
only one can be performed at a time.
4#: An ongoing_io boolean is introduced in order to capture and serialize
bus accessed. This is the one being released "sooner" than before,
because we only need to protect the chip against other SPI accesses
during the I/O phase, which for the destructive operations is the
beginning of the operation (when we send the command cycles and
possibly the data), while the second part of the operation (the
erase delay or the programmation delay) is when we can do something
else in another bank.
5#: Is handled by the three booleans presented above, if any of them is
set, the chip is not yet ready for the operation and must wait.
All these internal variables are protected by the existing lock, so that
changes in this structure are atomic. The serialization is handled with
a wait queue.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230328154105.448540-8-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
JFFS2:
- Fix memory corruption in error path
- Spelling and coding style fixes
UBI:
- Switch to BLK_MQ_F_BLOCKING in ubiblock
- Wire up partent device (for sysfs)
- Multiple UAF bugfixes
- Fix for an infinite loop in WL error path
UBIFS:
- Fix for multiple memory leaks in error paths
- Fixes for wrong space accounting
- Minor cleanups
- Spelling and coding style fixes
-----BEGIN PGP SIGNATURE-----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=fTYq
-----END PGP SIGNATURE-----
Merge tag 'ubifs-for-linus-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull jffs2, ubi and ubifs updates from Richard Weinberger:
"JFFS2:
- Fix memory corruption in error path
- Spelling and coding style fixes
UBI:
- Switch to BLK_MQ_F_BLOCKING in ubiblock
- Wire up partent device (for sysfs)
- Multiple UAF bugfixes
- Fix for an infinite loop in WL error path
UBIFS:
- Fix for multiple memory leaks in error paths
- Fixes for wrong space accounting
- Minor cleanups
- Spelling and coding style fixes"
* tag 'ubifs-for-linus-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs: (36 commits)
ubi: block: Fix a possible use-after-free bug in ubiblock_create()
ubifs: make kobj_type structures constant
mtd: ubi: block: wire-up device parent
mtd: ubi: wire-up parent MTD device
ubi: use correct names in function kernel-doc comments
ubi: block: set BLK_MQ_F_BLOCKING
jffs2: Fix list_del corruption if compressors initialized failed
jffs2: Use function instead of macro when initialize compressors
jffs2: fix spelling mistake "neccecary"->"necessary"
ubifs: Fix kernel-doc
ubifs: Fix some kernel-doc comments
UBI: Fastmap: Fix kernel-doc
ubi: ubi_wl_put_peb: Fix infinite loop when wear-leveling work failed
ubi: Fix UAF wear-leveling entry in eraseblk_count_seq_show()
ubi: fastmap: Fix missed fm_anchor PEB in wear-leveling after disabling fastmap
ubifs: ubifs_releasepage: Remove ubifs_assert(0) to valid this process
ubifs: ubifs_writepage: Mark page dirty after writing inode failed
ubifs: dirty_cow_znode: Fix memleak in error handling path
ubifs: Re-statistic cleaned znode count if commit failed
ubi: Fix permission display of the debugfs files
...
* Check the data only read pattern only once
* Prepare the late addition of supported operation checks
* Support for sequential cache reads
* Fix nand_chip kdoc
Raw NAND changes:
* Fsl_elbc: Propagate HW ECC settings to HW
* Marvell: Add missing layouts
* Pasemi: Don't use static data to track per-device state
* Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
* tmio_nand: Remove driver
* vf610_nfc: Use regular comments for functions
SPI-NAND changes:
* Add support for AllianceMemory AS5F34G04SND
* Macronix: use scratch buffer for DMA operation
NAND ECC changes:
* Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmP3L4MACgkQJWrqGEe9
VoSVKgf+PUOBlR6U/QaNlzavYsTOz1Hgc9MjuC32CtStED8/uKfEG9odBRw1Fp+I
fNpgVnaWrU7KpW9yzsMTLQy//6lI/Hjn4KUMqKcsBmN3dOvzca60YrbehWLlrARb
exRDFvwuw6qZ0jRYMsKC9jsKhvU69TXnAWCdC+TSWRwfXci5dfjm3HxMNpRvT+PQ
q3sWqFMGj+omLOr/R+sBzhSV0WU1FpQsG9NB6I0VbFiJGy9YMMaI2tr/TKJyYeqM
CM0T3tccjKAajJ9i9qKIPZnRYWQYx/FyJ5Uyg6DRxjeoVjsFhGom1pQbH/2eHVs6
iND3n1yQCsnPaR/D7yRZgiTERQzqdw==
=psZR
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.3' into mtd/next
NAND core changes:
* Check the data only read pattern only once
* Prepare the late addition of supported operation checks
* Support for sequential cache reads
* Fix nand_chip kdoc
Raw NAND changes:
* Fsl_elbc: Propagate HW ECC settings to HW
* Marvell: Add missing layouts
* Pasemi: Don't use static data to track per-device state
* Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
* tmio_nand: Remove driver
* vf610_nfc: Use regular comments for functions
SPI-NAND changes:
* Add support for AllianceMemory AS5F34G04SND
* Macronix: use scratch buffer for DMA operation
NAND ECC changes:
* Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
ubiblock devices were previously only identifyable by their name, but
not connected to their parent UBI volume device e.g. in sysfs.
Properly parent ubiblock device as descendant of a UBI volume device
to reflect device model hierachy.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Describe the continuous read nand_chip fields to avoid the following
htmldocs warning:
include/linux/mtd/rawnand.h:1325: warning: Function parameter or member
'cont_read' not described in 'nand_chip'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 003fe4b954 ("mtd: rawnand: Support for sequential cache reads")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230116094735.11483-1-miquel.raynal@bootlin.com
Add support for sequential cache reads for controllers using the generic
core helpers for their fast read/write helpers.
Sequential reads may reduce the overhead when accessing physically
continuous data by loading in cache the next page while the previous
page gets sent out on the NAND bus.
The ONFI specification provides the following additional commands to
handle sequential cached reads:
* 0x31 - READ CACHE SEQUENTIAL:
Requires the NAND chip to load the next page into cache while keeping
the current cache available for host reads.
* 0x3F - READ CACHE END:
Tells the NAND chip this is the end of the sequential cache read, the
current cache shall remain accessible for the host but no more
internal cache loading operation is required.
On the bus, a multi page read operation is currently handled like this:
00 -- ADDR1 -- 30 -- WAIT_RDY (tR+tRR) -- DATA1_IN
00 -- ADDR2 -- 30 -- WAIT_RDY (tR+tRR) -- DATA2_IN
00 -- ADDR3 -- 30 -- WAIT_RDY (tR+tRR) -- DATA3_IN
Sequential cached reads may instead be achieved with:
00 -- ADDR1 -- 30 -- WAIT_RDY (tR) -- \
31 -- WAIT_RDY (tRCBSY+tRR) -- DATA1_IN \
31 -- WAIT_RDY (tRCBSY+tRR) -- DATA2_IN \
3F -- WAIT_RDY (tRCBSY+tRR) -- DATA3_IN
Below are the read speed test results with regular reads and
sequential cached reads, on NXP i.MX6 VAR-SOM-SOLO in mapping mode with
a NAND chip characterized with the following timings:
* tR: 20 µs
* tRCBSY: 5 µs
* tRR: 20 ns
and the following geometry:
* device size: 2 MiB
* eraseblock size: 128 kiB
* page size: 2 kiB
============= Normal read @ 33MHz =================
mtd_speedtest: eraseblock read speed is 15633 KiB/s
mtd_speedtest: page read speed is 15515 KiB/s
mtd_speedtest: 2 page read speed is 15398 KiB/s
===================================================
========= Sequential cache read @ 33MHz ===========
mtd_speedtest: eraseblock read speed is 18285 KiB/s
mtd_speedtest: page read speed is 15875 KiB/s
mtd_speedtest: 2 page read speed is 16253 KiB/s
===================================================
We observe an overall speed improvement of about 5% when reading
2 pages, up to 15% when reading an entire block. This is due to the
~14us gain on each additional page read (tR - (tRCBSY + tRR)).
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
Tested-by: Liao Jaime <jaimeliao.tw@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20230112093637.987838-4-miquel.raynal@bootlin.com
Instead of checking if a pattern is supported each time we need it,
let's create a bitfield that only the core would be allowed to fill at
startup time. The core and the individual drivers may then use it in
order to check what operation they should use. This bitfield is supposed
to grow over time.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Liao Jaime <jaimeliao.tw@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20230112093637.987838-2-miquel.raynal@bootlin.com
When MTD or MTD_CFI_GEOMETRY is disabled, the spi-intel driver
fails to build, as it includes the shared CFI header:
include/linux/mtd/cfi.h:62:2: error: #warning No CONFIG_MTD_CFI_Ix selected. No NOR chip support can work. [-Werror=cpp]
62 | #warning No CONFIG_MTD_CFI_Ix selected. No NOR chip support can work.
linux/mtd/spi-nor.h does not actually need to include cfi.h, so
remove the inclusion here to fix the warning. This uncovers a
missing #include in spi-nor/core.c so add that there to
prevent a different build issue.
Fixes: e23e5a05d1 ("mtd: spi-nor: intel-spi: Convert to SPI MEM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Tokunori Ikegami <ikegami.t@gmail.com>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221220141352.1486360-1-arnd@kernel.org
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmOJ59AACgkQS1VPR6WN
FOnzOQf/WLBTNFtPcJoS7cdjlh4fuGySDUKuLifOX+Tmk/ki3XFCZR98cESgb5m+
hCyFDeER/qfdOK9ObT3K1GBS6x7zx8YkskbucjAU0vlIsr2ZHCjNpNiAHrADsKjR
579N0Xwh2ibh7uVJ1xvsPwObdAc8P/tjGHHWF6hGEZzIPYXJVce+qDktkkLfbZ/P
Fik6+y3h68wW/0kDNt/gNmNcb5Z3fjxySs21Np5sy7bUtVVBjHWLo0OpjNadDH9M
m6AkhFA5h9OVl5E4jHBpxc4NvlAa5f6520vESpieseNJiIMWo0W/eSkVsframFew
ILdtXCHjkbS6kgvSpUViobMFsgCjaA==
=Yi2q
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.2' into mtd/next
SPI NOR core changes:
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Fix merge conflict in the jedec,spi-nor bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
At the moment, we print the JEDEC ID that is stored in our database. The
generic flash support won't have such an entry in our database. To find
out the JEDEC ID later we will have to cache it. There is also another
advantage: If the flash is found in the database, the ID could be
truncated because the ID of the entry is used which can be shorter. Some
flashes still holds valuable information in the bytes after the JEDEC ID
and come in handy during debugging of when coping with INFO6() entries.
These are not accessible for now.
Save a copy of the ID bytes after reading and display it via debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-4-michael@walle.cc
Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and features,
the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0GQmA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylyVQCeNJjZ3hy+Wz8WkPSY+NkehuIhyCIAnjXMOJP8
5G/JQ+rpcclr7VOXlS66
=zVkU
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and
features, the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (411 commits)
w1: Split memcpy() of struct cn_msg flexible array
spmi: pmic-arb: increase SPMI transaction timeout delay
spmi: pmic-arb: block access for invalid PMIC arbiter v5 SPMI writes
spmi: pmic-arb: correct duplicate APID to PPID mapping logic
spmi: pmic-arb: add support to dispatch interrupt based on IRQ status
spmi: pmic-arb: check apid against limits before calling irq handler
spmi: pmic-arb: do not ack and clear peripheral interrupts in cleanup_irq
spmi: pmic-arb: handle spurious interrupt
spmi: pmic-arb: add a print in cleanup_irq
drivers: spmi: Directly use ida_alloc()/free()
MAINTAINERS: add TI ECAP driver info
counter: ti-ecap-capture: capture driver support for ECAP
Documentation: ABI: sysfs-bus-counter: add frequency & num_overflows items
dt-bindings: counter: add ti,am62-ecap-capture.yaml
counter: Introduce the COUNTER_COMP_ARRAY component type
counter: Consolidate Counter extension sysfs attribute creation
counter: Introduce the Count capture component
counter: 104-quad-8: Add Signal polarity component
counter: Introduce the Signal polarity component
counter: interrupt-cnt: Implement watch_validate callback
...
MTD subsystem API allows interacting with MTD devices (e.g. reading,
writing, handling bad blocks). So far a random driver could get MTD
device only by its name (get_mtd_device_nm()). This change allows
getting them also by a DT node.
This API is required for drivers handling DT defined MTD partitions in a
specific way (e.g. U-Boot (sub)partition with environment variables).
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220916122100.170016-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend struct mtd_req_stats with two new fields holding the number of
corrected bitflips and uncorrectable errors detected during a read
operation. This is a prerequisite for ultimately passing those counters
to user space, where they can be useful to applications for making
better-informed choices about moving data around.
Unlike 'max_bitflips' (which is set - in a common code path - to the
return value of a function called while the MTD device's mutex is held),
these counters have to be maintained in each MTD driver which defines
the '_read_oob' callback because the statistics need to be calculated
while the MTD device's mutex is held.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220629125737.14418-4-kernel@kempniu.pl
mtd_read_oob() callers are currently oblivious to the details of ECC
errors detected during the read operation - they only learn (through the
return value) whether any corrected bitflips or uncorrectable errors
occurred. More detailed ECC information can be useful to user-space
applications for making better-informed choices about moving data
around.
Extend struct mtd_oob_ops with a pointer to a newly-introduced struct
mtd_req_stats and set its 'max_bitflips' field to the maximum number of
bitflips found in a single ECC step during the read operation performed
by mtd_read_oob(). This is a prerequisite for ultimately passing that
value back to user space.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220629125737.14418-2-kernel@kempniu.pl
- move SECT_4K_PMC flag out of the core as it's a vendor specific flag
- s/addr_width/addr_nbytes: address width means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes.
- do not change nor->addr_nbytes at SFDP parsing time. At the SFDP parsing
time we should not change members of struct spi_nor, but instead fill
members of struct spi_nor_flash_parameters which could later on be used
by the callers.
- track flash's internal address mode so that we can use 4B opcodes
together with opcodes that don't have a 4B opcode correspondent.
SPI NOR manufacturer drivers changes:
- esmt: Rename "f25l32qa" flash name to "f25l32qa-2s".
- micron-st: Skip FSR reading if SPI controller does not support it to
allow flashes that support FSR to work even when attached to such SPI
controllers.
- spansion: Add s25hl-t/s25hs-t IDs and fixups.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmLjfRkACgkQS1VPR6WN
FOn9BQf/bCkxIpGY64RoV5CLNuDj+d4nAlqa7YaL7ftkHvgpEJd8x540dWxYnTsW
FzOReFnZRtb4yjFAlOmYyqYhFuhWjDV4fmjWkeZwLqNM4GN80wKF3btf4V06gp5S
Levjgmqiz/qBsrz9QYdDcB8YLVMOgInQLV8fNrBaG2oLAdskrzXaAukzkmvwnrHM
iVQFZVLfP20qJOnoeahGJ7QObx2A8E9B2APXl9lOCTiVwuDwbFhkKQ3Vf7EqeOS1
BTwSRplAia/JvV+AsESQIL7C4I/xjDbIQ/UD9XsWD7yHo7f8FNi0fxrQ+j8HSnz9
49Ho+csCSV3MMqwnzQT6ciDzzd2zag==
=MJ3w
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.20' into mtd/next
SPI NOR core changes:
- move SECT_4K_PMC flag out of the core as it's a vendor specific flag
- s/addr_width/addr_nbytes: address width means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes.
- do not change nor->addr_nbytes at SFDP parsing time. At the SFDP parsing
time we should not change members of struct spi_nor, but instead fill
members of struct spi_nor_flash_parameters which could later on be used
by the callers.
- track flash's internal address mode so that we can use 4B opcodes
together with opcodes that don't have a 4B opcode correspondent.
SPI NOR manufacturer drivers changes:
- esmt: Rename "f25l32qa" flash name to "f25l32qa-2s".
- micron-st: Skip FSR reading if SPI controller does not support it to
allow flashes that support FSR to work even when attached to such SPI
controllers.
- spansion: Add s25hl-t/s25hs-t IDs and fixups.
Address width was an unfortunate name, as it means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes. s/addr_width/addr_nbytes throughout the entire SPI NOR
framework.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-2-tudor.ambarus@microchip.com
The only thing that could theoretically fail in that function is
mtd_device_unregister(). However it's not supposed to fail and when
used correctly it doesn't. So wail loudly if it does anyhow.
This matches how other drivers (e.g. nand/raw/nandsim.c) use
mtd_device_unregister().
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-2-u.kleine-koenig@pengutronix.de
* Call of_platform_populate() for MTD partitions
* Check devicetree alias for index
* mtdoops:
- Add a timestamp to the mtdoops header.
- Create a header structure for the saved mtdoops.
- Fix the size of the header read buffer.
* mtdblock: Warn if opened on NAND
* Bindings:
- reserved-memory: Support MTD/block device
- jedec,spi-nor: remove unneeded properties
- Extend fixed-partitions binding
- Add Sercomm (Suzhou) Corporation vendor prefix
MTD driver changes:
* st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
* phram:
- Allow cached mappings
- Allow probing via reserved-memory
* maps: ixp4xx: Drop driver
* bcm47xxpart: Print correct offset on read error
CFI driver changes:
* Rename chip_ready variables
* Add S29GL064N ID definition
* Use chip_ready() for write on S29GL064N
* Move and rename chip_check/chip_ready/chip_good_for_write
NAND core changes:
* Print offset instead of page number for bad blocks
Raw NAND controller drivers:
* Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
* CS553X: simplify the return expression of cs553x_write_ctrl_byte()
* Davinci: Remove redundant unsigned comparison to zero
* Denali: Use managed device resources
* GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
* Intel: Fix possible null-ptr-deref in ebu_nand_probe()
* MPC5121: Check before clk_disable_unprepare() not needed
* Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
* OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
* Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
* Rockchip: Check before clk_disable_unprepare() not needed
* TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
* Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
* Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
* XTX: Add support for XT26G0xA
SPI NOR core changes:
* Read back written SR value to make sure the write was done correctly.
* Introduce a common function for Read ID that manufacturer drivers can
use to verify the Octal DTR switch worked correctly.
* Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
* Clarify rdsr dummy cycles documentation.
* Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
* Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
* Move spi_nor_write_ear() to Winbond module since only Winbond flashes
use it.
* Rework Micron and Cypress Octal DTR enable methods to improve
readability.
* Use the common Read ID function to verify switch to Octal DTR mode for
Micron and Cypress flashes.
* Skip polling status on volatile register writes for Micron and Cypress
flashes since the operation is instant.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmKHhXEACgkQJWrqGEe9
VoQ4FQgAwTWnv7Eps8ngxlOE1WW1Kx+XUFCYN7mUKmDycgRKWWqF0OUu3pU6T3Si
XoOixajzsPC7AJtXbbGKUkH3UtqapCZ/OVxMJzY1S1zKVgS72ChvPth+rNOA5H6f
wkwCRYBCm51hYAlOQeRoFtwLEpOP17KTZw9Jn/u5RVwbQedQnzPj5sb6PddejjF4
9nlk2auJHzENBEEBG3WLRNgvGep8mNNFarzWB4iWrMcG0w1EgBksbIdshoBmu7vj
nKcDJbyA81DqX+8d56BfAFih8H2yCXZmhUzMK+zqnNkd1NuPnDDnrQYFKmKm2hAg
3bIMIzi+8dl/m0TY6BHPHj8oIYpjYA==
=P95J
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Call of_platform_populate() for MTD partitions
- Check devicetree alias for index
- mtdoops:
- Add a timestamp to the mtdoops header.
- Create a header structure for the saved mtdoops.
- Fix the size of the header read buffer.
- mtdblock: Warn if opened on NAND
- Bindings:
- reserved-memory: Support MTD/block device
- jedec,spi-nor: remove unneeded properties
- Extend fixed-partitions binding
- Add Sercomm (Suzhou) Corporation vendor prefix
MTD driver changes:
- st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
- phram:
- Allow cached mappings
- Allow probing via reserved-memory
- maps: ixp4xx: Drop driver
- bcm47xxpart: Print correct offset on read error
CFI driver changes:
- Rename chip_ready variables
- Add S29GL064N ID definition
- Use chip_ready() for write on S29GL064N
- Move and rename chip_check/chip_ready/chip_good_for_write
NAND core changes:
- Print offset instead of page number for bad blocks
Raw NAND controller drivers:
- Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
- CS553X: simplify the return expression of cs553x_write_ctrl_byte()
- Davinci: Remove redundant unsigned comparison to zero
- Denali: Use managed device resources
- GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
- Intel: Fix possible null-ptr-deref in ebu_nand_probe()
- MPC5121: Check before clk_disable_unprepare() not needed
- Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
- OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
- Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
- Rockchip: Check before clk_disable_unprepare() not needed
- TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
- Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
- Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
- XTX: Add support for XT26G0xA
SPI NOR core changes:
- Read back written SR value to make sure the write was done
correctly.
- Introduce a common function for Read ID that manufacturer drivers
can use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond
flashes use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
readability.
- Use the common Read ID function to verify switch to Octal DTR mode
for Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and
Cypress flashes since the operation is instant"
* tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (68 commits)
mtd: st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
dt-bindings: mtd: partitions: Extend fixed-partitions binding
dt-bindings: Add Sercomm (Suzhou) Corporation vendor prefix
mtd: phram: Allow cached mappings
mtd: call of_platform_populate() for MTD partitions
mtd: rawnand: renesas: Use runtime PM instead of the raw clock API
dt-bindings: mtd: renesas: Fix the NAND controller description
mtd: rawnand: mpc5121: Check before clk_disable_unprepare() not needed
mtd: rawnand: rockchip: Check before clk_disable_unprepare() not needed
mtd: nand: MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
mtd: rawnand: cs553x: simplify the return expression of cs553x_write_ctrl_byte()
mtd: rawnand: kioxia: Add support for TH58NVG3S0HBAI4
mtd: spi-nor: debugfs: fix format specifier
mtd: spi-nor: support eon en25qh256a variant
mtd: spi-nor: winbond: add support for W25Q512NW-IM
mtd: spi-nor: expose internal parameters via debugfs
mtd: spi-nor: export spi_nor_hwcaps_pp2cmd()
mtd: spi-nor: move spi_nor_write_ear() to winbond module
mtd: spi-nor: amend the rdsr dummy cycles documentation
mtd: cfi_cmdset_0002: Rename chip_ready variables
...
* Print offset instead of page number for bad blocks
Raw NAND controller drivers:
* Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
* CS553X: simplify the return expression of cs553x_write_ctrl_byte()
* Davinci: Remove redundant unsigned comparison to zero
* Denali: Use managed device resources
* GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
* Intel: Fix possible null-ptr-deref in ebu_nand_probe()
* MPC5121: Check before clk_disable_unprepare() not needed
* Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
* OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
* Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
* Rockchip: Check before clk_disable_unprepare() not needed
* TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
* Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
* Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
* XTX: Add support for XT26G0xA
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmKD51AACgkQJWrqGEe9
VoQJ8AgAo8qjO5QQmd76v1q1Regxxl7RsH7hr7r9gJfgTwzhQC/xIyTiorcVPG7B
UDNu4Dwe3OAPbmU54TQNS/AMQkgHGMcIRTVut8+oL+ZnjYl+gv261GxmsfxaK/Hu
Vvvq9X0iyaKpZfyq3uksbsxiXbwMn4fHT7Reaimc9Thw+XKD7AcYWCuFb9GAWfaf
XQUVLg6y4Qk4BR9ZpYAx2v5FH4amJV9RKKTIqiymwcjnBZjYOI29wgKwY1hX+3bm
2Wu4wcccWhDzlV0Casf/hIGBydKx3omV+cJHLtmx7s+dqPvYSUGuvR2nbq5wuMqp
ZcAYeRhGEAYMYcMB/QuKmh4g/Js26w==
=QyqB
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.19' into mtd/next
NAND core:
* Print offset instead of page number for bad blocks
Raw NAND controller drivers:
* Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
* CS553X: simplify the return expression of cs553x_write_ctrl_byte()
* Davinci: Remove redundant unsigned comparison to zero
* Denali: Use managed device resources
* GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
* Intel: Fix possible null-ptr-deref in ebu_nand_probe()
* MPC5121: Check before clk_disable_unprepare() not needed
* Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
* OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
* Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
* Rockchip: Check before clk_disable_unprepare() not needed
* TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
* Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
* Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
* XTX: Add support for XT26G0xA
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Read back written SR value to make sure the write was done correctly.
- Introduce a common function for Read ID that manufacturer drivers can
use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond flashes
use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
readability.
- Use the common Read ID function to verify switch to Octal DTR mode for
Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and Cypress
flashes since the operation is instant.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQTlUWNzXGEo3bFmyIR4drqP028CQUCYoH1/QAKCRAR4drqP028
CXQeAP9hAfNGV55cOsd+z+3+xOxKeAYN/PC7UmXSvFgJZKYEqgEA/UF+SwsrOTyd
x+5UwNSOvrUX404j6ROP0kH4/kzARAY=
=Krne
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.19' into mtd/next
SPI NOR core changes:
- Read back written SR value to make sure the write was done correctly.
- Introduce a common function for Read ID that manufacturer drivers can
use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond flashes
use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
readability.
- Use the common Read ID function to verify switch to Octal DTR mode for
Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and Cypress
flashes since the operation is instant.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no way to gather all information to verify support for a new
flash chip. Also if you want to convert an existing flash chip to the
new SFDP parsing, there is not enough information to determine if the
flash will work like before. To ease this development, expose internal
parameters via the debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429102018.2361038-2-michael@walle.cc
The "Extended Address Register" is winbond specific. If the flash is
larger than 16MiB and is used in 3 byte address mode, it is used to set
the remaining address bits. Move the write_ear() function, the opcode
macros and the spimem op template into the winbond module and rename
them accordingly.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429100153.2338501-1-michael@walle.cc
Since commit dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to
check correct value") buffered writes fail on S29GL064N. This is
because, on S29GL064N, reads return 0xFF at the end of DQ polling for
write completion, where as, chip_good() check expects actual data
written to the last location to be returned post DQ polling completion.
Fix is to revert to using chip_good() for S29GL064N which only checks
for DQ lines to settle down to determine write completion.
Link: https://lore.kernel.org/r/b687c259-6413-26c9-d4c9-b3afa69ea124@pengutronix.de/
Fixes: dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")
Cc: stable@vger.kernel.org
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220323170458.5608-3-ikegami.t@gmail.com
* Also parse the default nand-ecc-engine property if available
* Make mtk_ecc.c a separated module
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmJpa+MACgkQJWrqGEe9
VoTVPwf+PjOPS9MH+3wQkEsqwHtJyC9dvfTRWNSkzJEos0710jl6peeWjo1ift1A
4JLMI3TGHWbNqBykpSLxZPVc6X/toGoMz6/2OussnYQBYgXjLNOgWQqS4kZZmK7D
BARpke8TTqglJyat7NpGNo1EGWA4EtYqwvoPT+H0LMLQbe/NQD0k4RaRNpw+BwPq
gaBHZf/CmN4oG0QrPPvS7jrm0dgWrQgTqRf9zzOnml3m22q3PGMnmY1A1CunBsFn
HK+GxYUOeemPc40mET+U1x6O0+VNlxW2KQ+fZoNHnljd55zq1Cp4mXfr7KuFgfDK
4xMAAoI5cMp8kpLLVUBlD4uzOj3fow==
=FBXD
-----END PGP SIGNATURE-----
Merge tag 'mtd/mtk-spi-nand-for-5.19' into nand/next
Mediatek ECC changes:
* Also parse the default nand-ecc-engine property if available
* Make mtk_ecc.c a separated module
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit 46b5889cc2 ("mtd: implement proper partition handling")
started using "mtd_get_master_ofs()" in mtd callbacks to determine
memory offsets by means of 'part' field from mtd_info, what previously
was smashed accessing 'master' field in the mtd_set_dev_defaults() method.
That provides wrong offset what causes hardware access errors.
Just make 'part', 'master' as separate fields, rather than using
union type to avoid 'part' data corruption when mtd_set_dev_defaults()
is called.
Fixes: 46b5889cc2 ("mtd: implement proper partition handling")
Signed-off-by: Oleksandr Ocheretnyi <oocheret@cisco.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220417184649.449289-1-oocheret@cisco.com
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmI021sACgkQJWrqGEe9
VoTEcggAiFXD+oR0VXTsykiNDiopsAUZwLPGuqk8gvD4ozOYCoAEoYrtnBM6Uybz
W6Hu6Eow/ri1H+uVygUw3RYa4TpxrZrmZnJ1YimXxZjbLYjgE3FS9vzh2l4Bu3yo
fkkQH+nFvk9qVIK8qolAny+LWl37gkSnCd6mPPksYaG5Ds1n1ZgyTZVUz5TOWAjG
QAWUQQfO1iu7+u4CXa9JRTkCf55bT6v6c9Ryq6MA+ok6jVRN6Cj9WhxHtCB5vmOH
Ndmu4V8BqaNKg39ltolqSPuwt3GEh707LRr+YakfnaOM7Sf8E/evn/THSkHwY/yn
bAjpU1gvS13nJ++s8nHwIhHKhoYjTg==
=4Uke
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.18' into mtd/next
Raw NAND core changes:
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmInffUACgkQS1VPR6WN
FOn9fwf/SCIvgoScBNeQjW4cGTmh11oO+O8i2umibq0pQDLrNF6Ul7ykY6Fdm4Dc
+Ce7c4Vp0O+DRphIkaK5MtNgRmXMOQbqUKcNAQftFS0wCtJ+QVQzOvkVGS3jQA74
KVEY3Jiup3Q5qknBg0r890ENwRLmcGJaPi5DAO+uHcf6ItTpwjv3z6C2ZUeiH6UK
PMSwZgd86dwwH2eU4G5EoAjA+nqOcVvH0V1F49DFsGZ3kkmUS6nMNnSpb5SykszT
4uq+7+c3E2UOC0TlUkyX/xTv4DoZZDi6qqVEaV14bELL1a0FdltjKyIuWTds1Tei
rwPhEOkqOpSnBVjlUWb7icwef21NWg==
=QFe+
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.18' into mtd/next
SPI NOR core changes:
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
partid and partname debugfs files were used just by SPI NOR, but they were
replaced by sysfs entries. Since these debugfs files are no longer used in
mtd, remove dead code. The directory is kept as it is used by nandsim,
mtdswap and docg3.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220225144656.634682-1-tudor.ambarus@microchip.com
The clear status register flags is only available on spansion flashes.
Move all the functions around that into the spanion module.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-29-michael@walle.cc
The flag status register is only available on micron flashes. Move all
the functions around that into the micron module.
This is almost a mechanical move except for the spi_nor_fsr_ready()
which now also checks the normal status register. Previously, this was
done in spi_nor_ready().
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-25-michael@walle.cc
Mechanically move all the xilinx functions to its own module.
Then register the new flash specific ready() function.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-22-michael@walle.cc
that can be used by SPI controllers to manage SPI NANDs as well as
possibly by parallel NAND controllers. In particular, it brings support
for Macronix ECC engine that can be used with Macronix SPI controller.
The changes touch the NAND core, the NAND ECC core, the spi-mem layer, a
SPI controller driver and add a new NAND ECC driver, as well as a number
of binding updates.
Binding changes:
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmIPpwcACgkQJWrqGEe9
VoRbnwgAgW9tSKGp1B6eA3Xf7Or0SZfmC6H0scV8kfQ2i9OnMOuYMAGs+7whNrcx
Dvb9IfFOMra7umid98EI58YhLsu4IMDtc79Lp04HGY/emjZh47FpAEXZ/vr/45e9
lclUEmjHwUVJ5+XvFwnPLpIWiM0xeL3CN2rAi76uI5sII+Hxt6KkV7L9+N9IjhcA
GsG/8/A16ihbNjVrHoN+ofwmmZkySXvhK7IIg93Tv+VoJCBnn0eEDgtRXvsGoDuq
2xD87MEAhnXw+q9LtSSUwmA/uUCR2RscidGQ+LML0PwKDVUZhzBV8sNrNoPQy374
51XXDCkSF8NRK+FVXIUFTEctdVrE1A==
=UuhB
-----END PGP SIGNATURE-----
Merge tag 'mtd/spi-mem-ecc-for-5.18' into mtd/next
Topic branch bringing-in changes related to the support of ECC engines
that can be used by SPI controllers to manage SPI NANDs as well as
possibly by parallel NAND controllers. In particular, it brings support
for Macronix ECC engine that can be used with Macronix SPI controller.
The changes touch the NAND core, the NAND ECC core, the spi-mem layer, a
SPI controller driver and add a new NAND ECC driver, as well as a number
of binding updates.
Binding changes:
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Some SPI-NAND chips do not have a proper on-die ECC engine providing
error correction/detection. This is particularly an issue on embedded
devices with limited resources because all the computations must
happen in software, unless an external hardware engine is provided.
These external engines are new and can be of two categories: external
or pipelined. Macronix is providing both, the former being already
supported. The second, however, is very SoC implementation dependent
and must be instantiated by the SPI host controller directly.
An entire subsystem has been contributed to support these engines which
makes the insertion into another subsystem such as SPI quite
straightforward without the need for a lot of specific functions.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20220202144536.393792-1-miquel.raynal@bootlin.com
In order for pipelined ECC engines to be able to enable/disable the ECC
engine only when needed and avoid races when future parallel-operations
will be supported, we need to provide the information about the use of
the ECC engine in the direct mapping hooks. As direct mapping
configurations are meant to be static, it is best to create two new
mappings: one for regular 'raw' accesses and one for accesses involving
correction. It is up to the driver to use or not the new ECC enable
boolean contained in the spi-mem operation.
As dirmaps are not free (they consume a few pages of MMIO address space)
and because these extra entries are only meant to be used by pipelined
engines, let's limit their use to this specific type of engine and save
a bit of memory with all the other setups.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-9-miquel.raynal@bootlin.com
Introduce the support for another possible configuration: the ECC
engine may work as DMA master (pipelined) and move itself the data
to/from the NAND chip into the buffer, applying the necessary
corrections/computations on the fly.
This driver offers an ECC engine implementation that must be
instatiated from a SPI controller driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-17-miquel.raynal@bootlin.com
In a pipelined engine situation, we might either have the host which
internally has support for error correction, or have it using an
external hardware block for this purpose. In the former case, the host
is also the ECC engine. In the latter case, it is not. In order to get
the right pointers on the right devices (for example: in order to devm_*
allocate variables), let's introduce this helper which can safely be
called by pipelined ECC engines in order to retrieve the right device
structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-16-miquel.raynal@bootlin.com
Prevent rawnand access while in a suspended state.
Commit 013e6292aa ("mtd: rawnand: Simplify the locking") allows the
rawnand layer to return errors rather than waiting in a blocking wait.
Tested on a iMX6ULL.
Fixes: 013e6292aa ("mtd: rawnand: Simplify the locking")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220208085213.1838273-1-sean@geanix.com
Reduce the number of exported symbols by replacing:
- mtd_expert_analysis_warning (the error string)
- mtd_expert_analysis_mode (the boolean)
with a single helper:
- mtd_check_expert_analysis_mode
Calling this helper will both check/return the content of the internal
boolean -which is not exported anymore- and as well conditionally
WARN_ONCE() the user, like it was done before.
While on this function, make the error string local to the helper and
set it const. Only export this helper when CONFIG_DEBUG_FS is defined to
limit the growth of the Linux kernel size only for a debug feature on
production kernels.
Mechanically update all the consumers.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220128113414.1121924-1-miquel.raynal@bootlin.com
Introduce nand_to_ecc_ctx() which will allow to easily jump to the
private pointer of an ECC context given a NAND device. This is very
handy, from the prepare or finish ECC hook, to get the internal context
out of the NAND device object.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-14-miquel.raynal@bootlin.com
Add the necessary helpers to register/unregister hardware ECC engines
that will be called from ECC engine drivers.
Also add helpers to get the right engine from the user
perspective. Keep a reference of the in use ECC engine in order to
prevent modules to be unloaded. Put the reference when the engine gets
retired.
A static list of hardware (only) ECC engines is setup to keep track of
the registered engines.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-13-miquel.raynal@bootlin.com
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller drivers:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmHO9D0ACgkQJWrqGEe9
VoRglwf/SsGcY+7vlBM1VSbUMIF/j5/xuigHIW6AxiN/hu672GMVi7nP7aHg4t3m
DpO5X6ngYFHyW79uksRfwSun/JF1mOqF4De9zhs+cy8hlV12tgEmUNB3cbv4kuFQ
e/N8/mlNrNJ2oQ1C3G3HWe3sngh2vrkhuG49t7M2TJaGAo7V4RW3z9+glNpWMb7m
YIj6gXPjPx7vuEWv80GBUcWNKBzNdRVkrQnj3C2I/ZCslnwYWBLBQxX/U9/KDkPH
7i7MgeknAlV0G/W4TfnNSAKiWOcmWdbmuJ/lOWv4+skdXoMb0/rlC6kvJqOLvbF6
2nUrc9yFTwkNfVTGJm5eWJ0yDUHMgA==
=DQck
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.17' into mtd/next
Raw NAND core:
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller drivers:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Add Pratyush as SPI NOR co-maintainer.
- Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
- Rework the flash_info flags and clarify where one should be used.
- Initialize all flash parameters based on JESD216 SFDP where possible.
Flash parameters and settings that are SFDP discoverable should not be
duplicated via flash_info flags at flash declaration.
- Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer drivers changes:
- Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP standard,
or the SFDP tables which define those flash parameters are not defined
by the flash.
- Fix mtd size for s3an flashes.
- Write 2 bytes when disabling Octal DTR mode: 1 byte long transactions are
not allowed in 8D-8D-8D mode.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmHMJxcACgkQS1VPR6WN
FOk1Ywf9GrDTrGx8Brg08qC7m2ExIiyRBFnUL4yeD9/d8p0vqqGryXeyjbaVutHR
fKf/SFrrP+gmcJS7wx4EttafgV8MPMiV1ICu/vyq2JsOlKekSEk38BXpfNOXzsgQ
UPE92AW8+BTgoL5XohnHqHrFqs+FEHAa3jCEpntWoShznZMhZ6IDwZbVlrHJC5Ts
C0S0S45X5aFgOXdNC4B0UrxAu0OryxL+vjjzG3Jl1g8GbrC/vkbR5vkMXaVgZiie
RpZtsbkcYm9vhUxOgMY+rRi4mwiTxy5Z2/Vg4Jr8nQOurO/aIvC9IZVIS4zbFOTk
08WtqtexR5S/+GCGIijJ+0BlS58hgg==
=tiIB
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.17' into mtd/next
SPI NOR core changes:
- Add Pratyush as SPI NOR co-maintainer.
- Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
- Rework the flash_info flags and clarify where one should be used.
- Initialize all flash parameters based on JESD216 SFDP where possible.
Flash parameters and settings that are SFDP discoverable should not be
duplicated via flash_info flags at flash declaration.
- Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer drivers changes:
- Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP standard,
or the SFDP tables which define those flash parameters are not defined
by the flash.
- Fix mtd size for s3an flashes.
- Write 2 bytes when disabling Octal DTR mode: 1 byte long transactions are
not allowed in 8D-8D-8D mode.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When developping NAND controller drivers or when debugging filesystem
corruptions, it is quite common to need hacking locally into the
MTD/NAND core in order to get access to the content of the bad
blocks. Instead of having multiple implementations out there let's
provide a simple yet effective specific MTD-wide debugfs entry to fully
disable these checks on purpose.
A warning is added to inform the user when this mode gets enabled.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211118114659.1282855-1-miquel.raynal@bootlin.com
Commit d24dbd7541 ("mtd: maps: Get rid of the latch-addr-flash driver")
removed the last user of <linux/mtd/latch-addr-flash.h> but left the header
file behind. Nothing uses this file, delete it now.
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211102220203.940290-7-corbet@lwn.net
Move the function nand_read_page_hwecc_oob_first() (previously
nand_davinci_read_page_hwecc_oob_first()) to nand_base.c, and export it
as a GPL symbol, so that it can be used by more modules.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-4-paul@crapouillou.net
nor->page_size duplicated what nor->params->page_size indicates
for no good reason. page_size is a flash parameter of fixed value
and it is better suited to be found in nor->params->page_size.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20211029172633.886453-5-tudor.ambarus@microchip.com
All uses of MTD_MAX_{OOBFREE,ECCPOS}_ENTRIES_LARGE have been removed as
commit ef5eeea6e9 ("mtd: nand: brcm: switch to mtd_ooblayout_ops") and
commit aab616e31d ("mtd: kill the nand_ecclayout struct") replaced
struct nand_ecclayout by the new mtd_ooblayout_ops interface. Remove
these two macros therefore.
Reported-by: Yi Yang <yiyang13@huawei.com>
Signed-off-by: GONG, Ruiqi <gongruiqi1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210830083356.31702-1-gongruiqi1@huawei.com
* Convert list_for_each to entry variant
* Use MTD_DEVICE_ATTR_RO/RW() helper macros
* Remove unnecessary OOM messages
* Potential NULL dereference in mtd_otp_size()
* Fix freeing of otp_info buffer
* Create partname and partid debug files for child MTDs
* tests:
- Remove redundant assignment to err
- Fix error return code in mtd_oobtest_init()
* Add OTP NVMEM provider support
* Allow specifying of_node
* Convert sysfs sprintf/snprintf family to sysfs_emit
Bindings changes:
* Convert ti,am654-hbmc.txt to YAML schema
* spi-nor: add otp property
* Add OTP bindings
* add YAML schema for the generic MTD bindings
* Add brcm,trx-magic
MTD device drivers changes:
* Add support for microchip 48l640 EERAM
* Remove superfluous "break"
* sm_ftl:
- Fix alignment of block comment
* nftl:
- Return -ENOMEM when kmalloc failed
* nftlcore:
- Remove set but rewrite variables
* phram:
- Fix error return code in phram_setup()
* plat-ram:
- Remove redundant dev_err call in platram_probe()
MTD parsers changes:
* Qcom:
- Fix leaking of partition name
* Redboot:
- Fix style issues
- Seek fis-index-block in the right node
* trx:
- Allow to use TRX parser on Mediatek SoCs
- Allow to specify brcm, trx-magic in DT
Raw NAND core:
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
SPI NOR core changes:
* Ability to dump SFDP tables via sysfs
* Support for erasing OTP regions on Winbond and similar flashes
* Few API doc updates and fixes
* Locking support for MX25L12805D
SPI NOR controller drivers changes:
* Use SPI_MODE_X_MASK in nxp-spifi
* Intel Alder Lake-M SPI serial flash support
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmDcT+IACgkQJWrqGEe9
VoT5Sgf/dt92XA5K2SYNh58KPUwemB9DtkukmniGjo9AqSQwuzHxik3ITHBbFvwP
cSj5PAGoI+zpc+VQz+XuZF1Bsmxaqhy5c0aaJ9TZai2W6keB91in7nJPAhmAI5o2
4zhtAZ9qKp4pOwhFqn6jTd5+l38ok50go3HB4Ibw4UlLuvbUEv11DUcXGKnaAadH
tmXZALf65YAJVruPb4yw+cv7BVVgOPQL8C8ILtsrue7Zgya3JT1205Zbfdjo+X0v
Kl2gh7gGh1YLqzuLLBDUiDnfLIfiu/WTnPqxtqCULR9cLG4oXybXHZe9OsrP8E+P
T68+K8VvT5LKbGh47/OoUfLvrDguCA==
=XVaS
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- Convert list_for_each to entry variant
- Use MTD_DEVICE_ATTR_RO/RW() helper macros
- Remove unnecessary OOM messages
- Potential NULL dereference in mtd_otp_size()
- Fix freeing of otp_info buffer
- Create partname and partid debug files for child MTDs
- tests:
- Remove redundant assignment to err
- Fix error return code in mtd_oobtest_init()
- Add OTP NVMEM provider support
- Allow specifying of_node
- Convert sysfs sprintf/snprintf family to sysfs_emit
Bindings changes:
- Convert ti,am654-hbmc.txt to YAML schema
- spi-nor: add otp property
- Add OTP bindings
- add YAML schema for the generic MTD bindings
- Add brcm,trx-magic
MTD device drivers changes:
- Add support for microchip 48l640 EERAM
- Remove superfluous "break"
- sm_ftl:
- Fix alignment of block comment
- nftl:
- Return -ENOMEM when kmalloc failed
- nftlcore:
- Remove set but rewrite variables
- phram:
- Fix error return code in phram_setup()
- plat-ram:
- Remove redundant dev_err call in platram_probe()
MTD parsers changes:
- Qcom:
- Fix leaking of partition name
- Redboot:
- Fix style issues
- Seek fis-index-block in the right node
- trx:
- Allow to use TRX parser on Mediatek SoCs
- Allow to specify brcm, trx-magic in DT
Raw NAND core:
- Allow SDR timings to be nacked
- Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing
set.
- Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
- Update dead URL
- Silence static checker warning in nand_setup_interface()
- BBT:
- Fix corner case in bad block table handling
- onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
- Atmel:
- Ensure the data interface is supported.
- Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
- brcmnand:
- Convert bindings to json-schema
- OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
- PL35X:
- New driver
- QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
- Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in
marvell_nfc_resume()
- R852:
- Use DEVICE_ATTR_RO() helper macro
- MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
- HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
- Light reorganisation for the introduction of a core resume handler
- Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
- Macronix:
- Add support for serial NAND flash
SPI NOR core changes:
- Ability to dump SFDP tables via sysfs
- Support for erasing OTP regions on Winbond and similar flashes
- Few API doc updates and fixes
- Locking support for MX25L12805D
SPI NOR controller drivers changes:
- Use SPI_MODE_X_MASK in nxp-spifi
- Intel Alder Lake-M SPI serial flash support"
* tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (125 commits)
mtd: spi-nor: remove redundant continue statement
mtd: rawnand: omap: Add larger page NAND chips support
mtd: rawnand: omap: Various style fixes
mtd: rawnand: omap: Check return values
mtd: rawnand: omap: Rename a macro
mtd: rawnand: omap: Aggregate the HW configuration of the ELM
mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller
dt-bindings: mtd: pl353-nand: Describe this hardware controller
MAINTAINERS: Add PL353 NAND controller entry
mtd: rawnand: qcom: avoid writing to obsolete register
mtd: rawnand: marvell: Minor documentation correction
mtd: rawnand: r852: use DEVICE_ATTR_RO() helper macro
mtd: spinand: add SPI-NAND MTD resume handler
mtd: spinand: Add spinand_init_flash() helper
mtd: spinand: add spinand_read_cfg() helper
mtd: rawnand: marvell: add missing clk_disable_unprepare() on error in marvell_nfc_resume()
mtd: rawnand: arasan: Finer grain NV-DDR configuration
mtd: rawnand: arasan: Rename the data interface register
mtd: rawnand: onfi: Fix endianness when reading NV-DDR values
mtd: rawnand: arasan: Use the right DMA mask
...
- Ability to dump SFDP tables via sysfs
- Support for erasing OTP regions on Winbond and similar flashes
- Few API doc updates and fixes
- Locking support for MX25L12805D
SPI NOR controller drivers changes:
- Use SPI_MODE_X_MASK in nxp-spifi
- Intel Alder Lake-M SPI serial flash support
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAmDVedQQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW45dXB/9Cn4xhHr73JZX54XDXQIgR7cFGbgXzZI+W
nrzLsCCpt0RrVwYQBXv8f6IY7u4uEgH+dhsXMruY+gYDh+NJoj9REMRr3PwWhH5o
R/ajQsDsBuGmtQ+I8RDpHYCQaNtgHqpnBQ+qmErbdK3FMxOyQ9gQkDC5097NDu4e
QXTaMJbRHsxTt8U7qRO/3XIEW10GHq33gftBcZD/DrKcTIO9GT6GGi9aGN9YPsv4
zDpjgOjZyqzJndgHavTQKxVC9csuQIUFcA2fgHO3rEaiF/TLUXemJAmrEMziVDS2
7c8KgtAssHRJdjCqUn6A0/JomNdxFzGPVN2bWf4/aLgnacXmn0Xe
=acH1
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.14' into mtd/next
SPI NOR core changes:
- Ability to dump SFDP tables via sysfs
- Support for erasing OTP regions on Winbond and similar flashes
- Few API doc updates and fixes
- Locking support for MX25L12805D
SPI NOR controller drivers changes:
- Use SPI_MODE_X_MASK in nxp-spifi
- Intel Alder Lake-M SPI serial flash support
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmDS290ACgkQJWrqGEe9
VoS77wgAgKnqfFwbqzdSecVmXai9roSNHi/aMpVJvvLHSTCV35iCcNNtrz0Jno56
t/8twVPPZUI6f3vPXk5+NjKRCb8Oif3oU+tNxqG6mwzrBRf5R80pYCMm+HGPWZaK
+MolqGAbgFO088DTK5fGNtmbnb5fPT174RKRBGEH5NgK5M1q95uF8fIjBXDcjVe2
hvAyoqqC7i/bp40sxRtglgBpYYz+KUjCX11JvJPa5IuVU+8ezZSKJLSo5/CtgIKJ
mRQ8p8myiUjZngcnebjTrAA5AwQ13ai9ofKG0pHkdxwOq4lSRNgKou0Hk5+oq+s0
BFEuXnUrdnJNU7+XV+kAqBoT6WOFzg==
=I/9X
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Raw NAND core:
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
Due to possible mode switching to 8D-8D-8D, it might not be possible to
read the SFDP after the initial probe. To be able to dump the SFDP via
sysfs afterwards, make a complete copy of it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Make use of spi-mem poll status APIs to let advanced controllers
optimize wait operations.
This should also fix the high CPU usage for system that don't have
a dedicated STATUS poll block logic.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210518162754.15940-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
New chips may feature a lot of CS because of their extended length. As
many controllers have been designed a decade ago, they usually only
feature just a couple. This does not mean that the entire range of
these chips cannot be accessed: it is just a matter of adding more
GPIO CS in the hardware design. A DT property has been added to
describe the CS array: cs-gpios.
Here is the code parsing it this new property, allocating what needs to
be, requesting the GPIOs and returning an array with the additional
available CS. The first entries of this array are left empty and are
reserved for native CS.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-3-miquel.raynal@bootlin.com
The struct gpio_desc is declared in the middle of the rawnand.h header,
right before the first function using it (nand_gpio_waitrdy). Before
adding a new function and to make it clear: move the declaration to the
top of the file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-2-miquel.raynal@bootlin.com
Until now the parameter of the ADDR_TIMING_MODE feature was just the
ONFI timing mode (from 0 to 5) because we were only supporting the SDR
data interface. In the same byte, bits 4 and 5 indicate which data
interface is being configured so use them to set the right mode and also
read them back to ensure the right timing has been setup on the chip's
side.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-17-miquel.raynal@bootlin.com
Most timings related to the bus timings are different between SDR and
NV-DDR. However, we identified 9 individual timings which are more
related to the NAND chip internals. These are common between the two
interface types. Fortunately, only these common timings are being shared
through the NAND core and its ->exec_op() interface, which allows the
writing of a simple macro checking the interface type and depending on
it, returning either the relevant SDR timing or the NV-DDR timing. This
is the purpose of the NAND_COMMON_TIMING_PS() macro.
As all this is evaluated at build time, one will immediately be notified
in case a non common timing is being accessed through this macro.
Two handy macros are also inserted at the same time, which use
PSEC_TO_NSEC or PSEC_TO_MSEC so that it is very easy to return timings
in milli-, nano- or pico-seconds, as usually requested by the internal
API.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-14-miquel.raynal@bootlin.com
Same logic as for the SDR path, let's create a
onfi_fill_nvddr_interface_config() helper to fill an interface
configuration structure with NV-DDR timings, given a specific ONFI mode.
There is one additional thing to do compared to SDR mode: tCAD timing
can be fast or slow and this depends on an ONFI parameter page bit. By
default the slow value is declared in the timings structure definition,
but this helper can shrink it down if necessary.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-12-miquel.raynal@bootlin.com
