Add support for adding GPIs to the event FIFO. This is done by adding
irq_chip support. Like this, one can use the input gpio_keys driver as a
"frontend" device and input handler.
As part of this change, we now implement .request() and .free() as we can't
blindly consume all available pins as GPIOs (example: some pins can be
used for forming a keymap matrix).
Also note that the number of pins can now be obtained from the parent,
top level device. Hence the 'max_gpio' variable can be removed.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-15-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
The ADP558x family supports a built in keypad matrix decoder which can
be added as an Input device. In order to both support the Input and the
GPIO device, we need to create a bitmap of the supported pins and track
their usage since they can either be used as GPIOs (GPIs) or as part of
the keymap.
We also need to mark special pins busy in case some features are being
used (ex: pwm or reset events).
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-14-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
The ADP558x family of devices can be programmed to respond to some
especial events, In case of the unlock events, one can lock the keypad
and use KEYS or GPIs events to unlock it. For the reset events, one can
again use a combinations of GPIs/KEYs in order to generate an event that
will trigger the device to generate an output reset pulse.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-13-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
These devices are capable of generate FIFO based events based on KEY or
GPI presses. Add support for handling these events. This is in
preparation of adding full support for keymap and gpis based events.
Reviewed-by: Lee Jones <lee@kernel.org>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-12-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for the adp5589 I/O expander. From a PWM point of view it is
pretty similar to adp5585. Main difference is the address
of registers meaningful for configuring the PWM.
Acked-by: Uwe Kleine-König <ukleinek@kernel.org>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-10-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
Support the adp5589 I/O expander which supports up to 19 pins. We need
to add a chip_info based struct since accessing register "banks"
and "bits" differs between devices.
Also some register addresses are different.
While at it move ADP558X_GPIO_MAX defines to the main header file and
rename them. That information will be needed by the top level device in
a following change.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-9-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
There are some differences in the register map between the devices.
Hence, add a register structure per device. This will be needed in
following patches.
On top of that adp5585_fill_regmap_config() is renamed and reworked so
that the current struct adp5585_info act as template (they indeed
contain all the different data between variants) which can then be
complemented depending on the device (as identified by the id register).
This is done like this since a lot of the data is pretty much the same
between variants of the same device.
Reviewed-by: Lee Jones <lee@kernel.org>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-8-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
The only thing changing between variants is the regmap default
registers. Hence, instead of having a regmap configuration for every
variant (duplicating lots of fields), add a chip info type of structure
with a regmap ID to identify which defaults to use and populate
regmap_config at runtime given a template plus the id. Also note that
between variants, the defaults can be the same which means the chip info
structure can be used in more than one compatible.
This will also make it simpler adding new chips with more variants.
Also note that the chip info structures are deliberately not const as
they will also contain lots of members that are the same between the
different devices variants and so we will fill those at runtime.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20250701-dev-adp5589-fw-v7-6-b1fcfe9e9826@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
The ADP5585 is a 10/11 input/output port expander with a built in keypad
matrix decoder, programmable logic, reset generator, and PWM generator.
This driver supports the chip by modelling it as an MFD device, with two
child devices for the GPIO and PWM functions.
The driver is derived from an initial implementation from NXP, available
in commit 8059835bee19 ("MLK-25917-1 mfd: adp5585: add ADI adp5585 core
support") in their BSP kernel tree. It has been extensively rewritten.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240722121100.2855-3-laurent.pinchart@ideasonboard.com
Signed-off-by: Lee Jones <lee@kernel.org>
