The Parade PS8830 is a USB4, DisplayPort and Thunderbolt 4 retimer,
controlled over I2C. It usually sits between a USB/DisplayPort PHY
and the Type-C connector, and provides orientation and altmode handling.
The boards that use this retimer are the ones featuring the Qualcomm
Snapdragon X Elite SoCs.
Add a driver with support for the following modes:
- DisplayPort 4-lanes
- DisplayPort 2-lanes + USB3
- USB3
There is another variant of this retimer which is called PS8833. It seems
to be really similar to the PS8830, so future-proof this driver by
naming it ps883x.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250206-x1e80100-ps8830-v6-2-60b1e49cfa8d@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212202913.23443-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Merrifield SoC uses these endpoints for tracing and they cannot
be re-allocated if being used because the side band flow control signals
are hard wired to certain endpoints:
• 1 High BW Bulk IN (IN#1) (RTIT)
• 1 1KB BW Bulk IN (IN#8) + 1 1KB BW Bulk OUT (Run Control) (OUT#8)
In device mode, since RTIT (EP#1) and EXI/RunControl (EP#8) uses
External Buffer Control (EBC) mode, these endpoints are to be mapped to
EBC mode (to be done by EXI target driver). Additionally TRB for RTIT
and EXI are maintained in STM (System Trace Module) unit and the EXI
target driver will as well configure the TRB location for EP #1 IN
and EP#8 (IN and OUT). Since STM/PTI and EXI hardware blocks manage
these endpoints and interface to OTG3 controller through EBC interface,
there is no need to enable any events (such as XferComplete etc)
for these end points.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The snps,reserved-endpoints property lists the reserved endpoints
that shouldn't be used for normal transfers. Add support for that
to the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare the gadget driver to handle the reserved endpoints that will be
not allocated at the initialisation time.
While at it, add a warning where the NULL endpoint should never happen.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A manual EC sysjump will restart the PPM and break communication with
the UCSI driver by disabling notifications in the initial PPM state.
Update cros_ec_ucsi to listen for PPM init events and treat them as a
system resume to re-establish communication with the PPM (ChromeOS EC).
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Łukasz Bartosik <ukaszb@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20250204024600.4138776-3-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As PD2.0 spec ("6.5.6.2 PSSourceOffTimer")，the PSSourceOffTimer is
used by the Policy Engine in Dual-Role Power device that is currently
acting as a Sink to timeout on a PS_RDY Message during a Power Role
Swap sequence. This condition leads to a Hard Reset for USB Type-A and
Type-B Plugs and Error Recovery for Type-C plugs and return to USB
Default Operation.
Therefore, after PSSourceOffTimer timeout, the tcpm state machine should
switch from PR_SWAP_SNK_SRC_SINK_OFF to ERROR_RECOVERY. This can also
solve the test items in the USB power delivery compliance test:
TEST.PD.PROT.SNK.12 PR_Swap – PSSourceOffTimer Timeout
[1] https://usb.org/document-library/usb-power-delivery-compliance-test-specification-0/USB_PD3_CTS_Q4_2025_OR.zip
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable <stable@kernel.org>
Signed-off-by: Jos Wang <joswang@lenovo.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Amit Sunil Dhamne <amitsd@google.com>
Link: https://lore.kernel.org/r/20250213134921.3798-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The role switch registration and set_role() can happen in parallel as they
are invoked independent of each other. There is a possibility that a driver
might spend significant amount of time in usb_role_switch_register() API
due to the presence of time intensive operations like component_add()
which operate under common mutex. This leads to a time window after
allocating the switch and before setting the registered flag where the set
role notifications are dropped. Below timeline summarizes this behavior
Thread1 | Thread2
usb_role_switch_register() |
| |
---> allocate switch |
| |
---> component_add() | usb_role_switch_set_role()
| | |
| | --> Drop role notifications
| | since sw->registered
| | flag is not set.
| |
--->Set registered flag.|
To avoid this, set the registered flag early on in the switch register
API.
Fixes: b787a3e781 ("usb: roles: don't get/set_role() when usb_role_switch is unregistered")
Cc: stable <stable@kernel.org>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250206193950.22421-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The behaviour of kthread_create_worker() was recently changed to align
with the one of kthread_create(). The kthread worker is created but not
awaken by default. This is to allow the use of kthread_affine_preferred()
and kthread_bind[_mask]() with kthread workers. In order to keep the
old behaviour and wake the kthread up, kthread_run_worker() must be
used. All the pre-existing users have been converted, except for UVC
that was introduced in the same merge window as the API change.
This results in hangs:
INFO: task UVCG:82 blocked for more than 491 seconds.
Tainted: G T 6.13.0-rc2-00014-gb04e317b5226 #1
task:UVCG state:D stack:0 pid:82
Call Trace:
__schedule
schedule
schedule_preempt_disabled
kthread
? kthread_flush_work
ret_from_fork
ret_from_fork_asm
entry_INT80_32
Fix this with converting UVCG kworker to the new API.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202502121025.55bfa801-lkp@intel.com
Fixes: f0bbfbd16b ("usb: gadget: uvc: rework to enqueue in pump worker from encoded queue")
Cc: stable <stable@kernel.org>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20250212135514.30539-1-frederic@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Teclast disk used on Huawei hisi platforms doesn't work well,
losing connectivity intermittently if LPM is enabled.
Add quirk disable LPM to resolve the issue.
Signed-off-by: Lei Huang <huanglei@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250212093829.7379-1-huanglei814@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_del() can lead to new work being scheduled in gadget->work
workqueue. This is observed, for example, with the dwc3 driver with the
following call stack:
device_del()
gadget_unbind_driver()
usb_gadget_disconnect_locked()
dwc3_gadget_pullup()
dwc3_gadget_soft_disconnect()
usb_gadget_set_state()
schedule_work(&gadget->work)
Move flush_work() after device_del() to ensure the workqueue is cleaned
up.
Fixes: 5702f75375 ("usb: gadget: udc-core: move sysfs_notify() to a workqueue")
Cc: stable <stable@kernel.org>
Signed-off-by: Roy Luo <royluo@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250204233642.666991-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When usb_control_msg is used in the get_bMaxPacketSize0 function, the
USB pipe does not include the endpoint device number. This can cause
failures when a usb hub port is reinitialized after encountering a bad
cable connection. As a result, the system logs the following error
messages:
usb usb2-port1: cannot reset (err = -32)
usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
usb usb2-port1: attempt power cycle
usb 2-1: new high-speed USB device number 5 using ci_hdrc
usb 2-1: device descriptor read/8, error -71
The problem began after commit 85d07c5562 ("USB: core: Unite old
scheme and new scheme descriptor reads"). There
usb_get_device_descriptor was replaced with get_bMaxPacketSize0. Unlike
usb_get_device_descriptor, the get_bMaxPacketSize0 function uses the
macro usb_rcvaddr0pipe, which does not include the endpoint device
number. usb_get_device_descriptor, on the other hand, used the macro
usb_rcvctrlpipe, which includes the endpoint device number.
By modifying the get_bMaxPacketSize0 function to use usb_rcvctrlpipe
instead of usb_rcvaddr0pipe, the issue can be resolved. This change will
ensure that the endpoint device number is included in the USB pipe,
preventing reinitialization failures. If the endpoint has not set the
device number yet, it will still work because the device number is 0 in
udev.
Cc: stable <stable@kernel.org>
Fixes: 85d07c5562 ("USB: core: Unite old scheme and new scheme descriptor reads")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250203105840.17539-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a frequent timeout during controller enter/exit from halt state
after toggling the run_stop bit by SW. This timeout occurs when
performing frequent role switches between host and device, causing
device enumeration issues due to the timeout. This issue was not present
when USB2 suspend PHY was disabled by passing the SNPS quirks
(snps,dis_u2_susphy_quirk and snps,dis_enblslpm_quirk) from the DTS.
However, there is a requirement to enable USB2 suspend PHY by setting of
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY bits when controller starts
in gadget or host mode results in the timeout issue.
This commit addresses this timeout issue by ensuring that the bits
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY are cleared before starting
the dwc3_gadget_run_stop sequence and restoring them after the
dwc3_gadget_run_stop sequence is completed.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250201163903.459-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fastboot tool for communicating with Android bootloaders does not
work reliably with this device if USB 2 Link Power Management (LPM)
is enabled.
Various fastboot commands are affected, including the
following, which usually reproduces the problem within two tries:
fastboot getvar kernel
getvar:kernel FAILED (remote: 'GetVar Variable Not found')
This issue was hidden on many systems up until commit 63a1f84549
("xhci: stored cached port capability values in one place") as the xhci
driver failed to detect USB 2 LPM support if USB 3 ports were listed
before USB 2 ports in the "supported protocol capabilities".
Adding the quirk resolves the issue. No drawbacks are expected since
the device uses different USB product IDs outside of fastboot mode, and
since fastboot commands worked before, until LPM was enabled on the
tested system by the aforementioned commit.
Based on a patch from Forest <forestix@nom.one> from which most of the
code and commit message is taken.
Cc: stable <stable@kernel.org>
Reported-by: Forest <forestix@nom.one>
Closes: https://lore.kernel.org/hk8umj9lv4l4qguftdq1luqtdrpa1gks5l@sonic.net
Tested-by: Forest <forestix@nom.one>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250206151836.51742-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Renesas R-Car D3 USB Download mode quirk and update comments
on all the other Renesas R-Car USB Download mode quirks to discern
them from each other. This follows R-Car Series, 3rd Generation
reference manual Rev.2.00 chapter 19.2.8 USB download mode .
Fixes: 6d853c9e41 ("usb: cdc-acm: Add DISABLE_ECHO for Renesas USB Download mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250209145708.106914-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we receive an initial fragment of size 8 bytes which specifies a wLength
of 1 byte (so the reassembled message is supposed to be 9 bytes long), and
we then receive a second fragment of size 9 bytes (which is not supposed to
happen), we currently wrongly bypass the fragment reassembly code but still
pass the pointer to the acm->notification_buffer to
acm_process_notification().
Make this less wrong by always going through fragment reassembly when we
expect more fragments.
Before this patch, receiving an overlong fragment could lead to `newctrl`
in acm_process_notification() being uninitialized data (instead of data
coming from the device).
Cc: stable <stable@kernel.org>
Fixes: ea2583529c ("cdc-acm: reassemble fragmented notifications")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the first fragment is shorter than struct usb_cdc_notification, we can't
calculate an expected_size. Log an error and discard the notification
instead of reading lengths from memory outside the received data, which can
lead to memory corruption when the expected_size decreases between
fragments, causing `expected_size - acm->nb_index` to wrap.
This issue has been present since the beginning of git history; however,
it only leads to memory corruption since commit ea2583529c
("cdc-acm: reassemble fragmented notifications").
A mitigating factor is that acm_ctrl_irq() can only execute after userspace
has opened /dev/ttyACM*; but if ModemManager is running, ModemManager will
do that automatically depending on the USB device's vendor/product IDs and
its other interfaces.
Cc: stable <stable@kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Renesas HCs require firmware upload to work, this is handled by the
xhci_pci_renesas driver. Other variants of those chips load firmware from
a SPI flash and are ready to work with xhci_pci alone.
A refactor merged in v6.12 broke the latter configuration so that users
are finding their hardware ignored by the normal driver and are forced to
enable the firmware loader which isn't really necessary on their systems.
Let xhci_pci work with those chips as before when the firmware loader is
disabled by kernel configuration.
Fixes: 25f51b76f9 ("xhci-pci: Make xhci-pci-renesas a proper modular driver")
Cc: stable <stable@kernel.org>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219616
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219726
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Tested-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://lore.kernel.org/r/20250128104529.58a79bfc@foxbook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids and a couple of related cleanups of
the device id table.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZ64AAwAKCRALxc3C7H1l
CEf5AP9m/cucRzOid2mOQiCYpD5zhMn/MZnH/AFB647nN2dFZwD/Rgs64qk2ZZUI
49XbIl6SeoLWp2CdUS/M7ra+jKqa3AE=
=OkGu
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.14-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.14-rc3
Here are some new modem device ids and a couple of related cleanups of
the device id table.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.14-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: drop MeiG Smart defines
USB: serial: option: fix Telit Cinterion FN990A name
USB: serial: option: add Telit Cinterion FN990B compositions
USB: serial: option: add MeiG Smart SLM828
The names RESERVE and RELEASE are not only used in <scsi/scsi_proto.h> but
also elsewhere in the kernel:
$ git grep -nHE 'define[[:blank:]]*(RESERVE|RELEASE)[[:blank:]]'
drivers/input/joystick/walkera0701.c:13:#define RESERVE 20000
drivers/s390/char/tape_std.h:56:#define RELEASE 0xD4 /* 3420 NOP, 3480 REJECT */
drivers/s390/char/tape_std.h:58:#define RESERVE 0xF4 /* 3420 NOP, 3480 REJECT */
Additionally, while the names of the symbolic constants RESERVE_10 and
RELEASE_10 include the command length, the command length is not included
in the RESERVE and RELEASE names. Address both issues by renaming the
RESERVE and RELEASE constants into RESERVE_6 and RELEASE_6 respectively.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20250210205031.2970833-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several MeiG Smart modems apparently use the same product id, making the
defines even less useful.
Drop them in favour of using comments consistently to make the id table
slightly less unwieldy.
Cc: stable@vger.kernel.org
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The correct name for FN990 is FN990A so use it in order to avoid
confusion with FN990B.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
While the MIDI jacks are configured correctly, and the MIDIStreaming
endpoint descriptors are filled with the correct information,
bNumEmbMIDIJack and bLength are set incorrectly in these descriptors.
This does not matter when the numbers of in and out ports are equal, but
when they differ the host will receive broken descriptors with
uninitialized stack memory leaking into the descriptor for whichever
value is smaller.
The precise meaning of "in" and "out" in the port counts is not clearly
defined and can be confusing. But elsewhere the driver consistently
uses this to match the USB meaning of IN and OUT viewed from the host,
so that "in" ports send data to the host and "out" ports receive data
from it.
Cc: stable <stable@kernel.org>
Fixes: c8933c3f79 ("USB: gadget: f_midi: allow a dynamic number of input and output ports")
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20250130195035.3883857-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dwc2_hsotg_udc_start(), e.g. when binding composite driver, "of_node"
is set to hsotg->dev->of_node.
It causes errors when binding the gadget driver several times, on
stm32mp157c-ev1 board. Below error is seen:
"pin PA10 already requested by 49000000.usb-otg; cannot claim for gadget.0"
The first time, no issue is seen as when registering the driver, of_node
isn't NULL:
-> gadget_dev_desc_UDC_store
-> usb_gadget_register_driver_owner
-> driver_register
...
-> really_probe -> pinctrl_bind_pins (no effect)
Then dwc2_hsotg_udc_start() sets of_node.
The second time (stop the gadget, reconfigure it, then start it again),
of_node has been set, so the probing code tries to acquire pins for the
gadget. These pins are hold by the controller, hence the error.
So clear gadget.dev.of_node in udc_stop() routine to avoid the issue.
Fixes: 7d7b22928b ("usb: gadget: s3c-hsotg: Propagate devicetree to gadget drivers")
Cc: stable <stable@kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20250124173325.2747710-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Robert Morris created a test program which can cause
usb_hub_to_struct_hub() to dereference a NULL or inappropriate
pointer:
Oops: general protection fault, probably for non-canonical address
0xcccccccccccccccc: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
CPU: 7 UID: 0 PID: 117 Comm: kworker/7:1 Not tainted 6.13.0-rc3-00017-gf44d154d6e3d #14
Hardware name: FreeBSD BHYVE/BHYVE, BIOS 14.0 10/17/2021
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_hub_adjust_deviceremovable+0x78/0x110
...
Call Trace:
<TASK>
? die_addr+0x31/0x80
? exc_general_protection+0x1b4/0x3c0
? asm_exc_general_protection+0x26/0x30
? usb_hub_adjust_deviceremovable+0x78/0x110
hub_probe+0x7c7/0xab0
usb_probe_interface+0x14b/0x350
really_probe+0xd0/0x2d0
? __pfx___device_attach_driver+0x10/0x10
__driver_probe_device+0x6e/0x110
driver_probe_device+0x1a/0x90
__device_attach_driver+0x7e/0xc0
bus_for_each_drv+0x7f/0xd0
__device_attach+0xaa/0x1a0
bus_probe_device+0x8b/0xa0
device_add+0x62e/0x810
usb_set_configuration+0x65d/0x990
usb_generic_driver_probe+0x4b/0x70
usb_probe_device+0x36/0xd0
The cause of this error is that the device has two interfaces, and the
hub driver binds to interface 1 instead of interface 0, which is where
usb_hub_to_struct_hub() looks.
We can prevent the problem from occurring by refusing to accept hub
devices that violate the USB spec by having more than one
configuration or interface.
Reported-and-tested-by: Robert Morris <rtm@csail.mit.edu>
Cc: stable <stable@kernel.org>
Closes: https://lore.kernel.org/linux-usb/95564.1737394039@localhost/
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/c27f3bf4-63d8-4fb5-ac82-09e3cd19f61c@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/gadget/udc/renesas_usb3.c: In function 'renesas_usb3_probe':
drivers/usb/gadget/udc/renesas_usb3.c:2638:73: warning: '%d'
directive output may be truncated writing between 1 and 11 bytes into a
region of size 6 [-Wformat-truncation=]
2638 | snprintf(usb3_ep->ep_name, sizeof(usb3_ep->ep_name), "ep%d", i);
^~~~~~~~~~~~~~~~~~~~~~~~ ^~ ^
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501201409.BIQPtkeB-lkp@intel.com/
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250122081231.47594-1-guoren@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c141ecc3ce ("of: Warn when of_property_read_bool() is
used on non-boolean properties") a warning is raised if this function
is used for property detection. of_property_present() is the correct
helper for this.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20250120144251.580981-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation sets the wMaxPacketSize of bulk in/out
endpoints to 1024 bytes at the end of the f_midi_bind function. However,
in cases where there is a failure in the first midi bind attempt,
consider rebinding. This scenario may encounter an f_midi_bind issue due
to the previous bind setting the bulk endpoint's wMaxPacketSize to 1024
bytes, which exceeds the ep->maxpacket_limit where configured dwc3 TX/RX
FIFO's maxpacket size of 512 bytes for IN/OUT endpoints in support HS
speed only.
Here the term "rebind" in this context refers to attempting to bind the
MIDI function a second time in certain scenarios. The situations where
rebinding is considered include:
* When there is a failure in the first UDC write attempt, which may be
caused by other functions bind along with MIDI.
* Runtime composition change : Example : MIDI,ADB to MIDI. Or MIDI to
MIDI,ADB.
This commit addresses this issue by resetting the wMaxPacketSize before
endpoint claim. And here there is no need to reset all values in the usb
endpoint descriptor structure, as all members except wMaxPacketSize and
bEndpointAddress have predefined values.
This ensures that restores the endpoint to its expected configuration,
and preventing conflicts with value of ep->maxpacket_limit. It also
aligns with the approach used in other function drivers, which treat
endpoint descriptors as if they were full speed before endpoint claim.
Fixes: 46decc82ff ("usb: gadget: unconditionally allocate hs/ss descriptor in bind operation")
Cc: stable@vger.kernel.org
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Link: https://lore.kernel.org/r/20250118060134.927-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'struct musb_fifo_cfg' are not modified in these drivers.
Constifying these structures moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
64381 5537 202 70120 111e8 drivers/usb/musb/musb_core.o
After:
=====
text data bss dec hex filename
64957 4929 202 70088 111c8 drivers/usb/musb/musb_core.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/26e6f3e25dc8e785d0034dd7e59918e455563e60.1737234596.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_probe to silence EPROBE_DEFER error on boot on i.MX8ULP:
[ 0.127301] mxs_phy 29910000.usb-phy: can't get the clock, err=-517
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Link: https://lore.kernel.org/r/20250203-defer_usb2-v3-1-428182286ce3@atmark-techno.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is easier to keep all command-specific quirks in a single place. Move
them to ucsi_gram_sync_control() as the code now allows us to return
modified messages data.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250120-ucsi-merge-commands-v2-3-462a1ec22ecc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is easier to keep all command-specific quirks in a single place. Move
them to ucsi_ccg_sync_control() as the code now allows us to return
modified messages data.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250120-ucsi-merge-commands-v2-2-462a1ec22ecc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the drivers emulate or handle some of the commands in the
platform-specific way. The code ends up being split between several
callbacks, which complicates emulation.
In preparation to reworking such drivers, move read_cci() and
read_message_in() calls into ucsi_sync_control_common().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Łukasz Bartosik <ukaszb@chromium.org>
Link: https://lore.kernel.org/r/20250120-ucsi-merge-commands-v2-1-462a1ec22ecc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"maxim,max3421" DT compatible is missing its SPI device ID entry, not
allowing module autoloading and leading to the following message:
"SPI driver max3421-hcd has no spi_device_id for maxim,max3421"
Fix this by adding the spi_device_id table.
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Link: https://lore.kernel.org/r/20250128195114.56321-1-alexander.stein@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 88785982a1 ("media: vb2: use lock if wait_prepare/finish
are NULL") it is no longer needed to set the wait_prepare/finish
vb2_ops callbacks as long as the lock field in vb2_queue is set.
Since the vb2_ops_wait_prepare/finish callbacks already rely on that field,
we can safely drop these callbacks.
This simplifies the code and this is a step towards the goal of deleting
these callbacks.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2fb746b8-31c4-44e0-bf7b-7a0758edf52a@xs4all.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the UCSI commands UCSI_SET_NEW_CAM,
UCSI_GET_ERROR_STATUS, UCSI_GET_CAM_CS, and UCSI_GET_LPM_PPM_INFO
support in debugfs to enhance PD/TypeC debugging capability.
Signed-off-by: Madhu M <madhu.m@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250118172455.701348-2-madhu.m@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename the SET_UOM UCSI command to SET_CCOM as per the UCSI 3.0 spec.
Signed-off-by: Madhu M <madhu.m@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250118172455.701348-1-madhu.m@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of driver core and debugfs updates for 6.14-rc1.
It's coming late in the merge cycle as there are a number of merge
conflicts with your tree now, and I wanted to make sure they were
working properly. To resolve them, look in linux-next, and I will send
the "fixup" patch as a response to the pull request.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at least
one user that does have a regression with these, but Al is working on
tracking down the fix for it. In my use (and everyone else's linux-next
use), it does not seem like a big issue at the moment.
Here's a short list of the things in here:
- driver core bindings for PCI, platform, OF, and some i/o functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing things
in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon".
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ5koPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymFHACfT5acDKf2Bov2Lc/5u3vBW/R6ChsAnj+LmgVI
hcDSPodj4szR40RRnzBd
=u5Ey
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the big set of driver core and debugfs updates for 6.14-rc1.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at
least one user that does have a regression with these, but Al is
working on tracking down the fix for it. In my use (and everyone
else's linux-next use), it does not seem like a big issue at the
moment.
Here's a short list of the things in here:
- driver core rust bindings for PCI, platform, OF, and some i/o
functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing
things in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon""
* tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
rust: device: Use as_char_ptr() to avoid explicit cast
rust: device: Replace CString with CStr in property_present()
devcoredump: Constify 'struct bin_attribute'
devcoredump: Define 'struct bin_attribute' through macro
rust: device: Add property_present()
saner replacement for debugfs_rename()
orangefs-debugfs: don't mess with ->d_name
octeontx2: don't mess with ->d_parent or ->d_parent->d_name
arm_scmi: don't mess with ->d_parent->d_name
slub: don't mess with ->d_name
sof-client-ipc-flood-test: don't mess with ->d_name
qat: don't mess with ->d_name
xhci: don't mess with ->d_iname
mtu3: don't mess wiht ->d_iname
greybus/camera - stop messing with ->d_iname
mediatek: stop messing with ->d_iname
netdevsim: don't embed file_operations into your structs
b43legacy: make use of debugfs_get_aux()
b43: stop embedding struct file_operations into their objects
carl9170: stop embedding file_operations into their objects
...
Here is the USB and Thunderbolt driver updates for 6.14-rc1. Nothing
huge in here, just lots of new hardware support and updates for existing
drivers. Changes here are:
- big gadget f_tcm driver update
- other gadget driver updates and fixes
- thunderbolt driver updates for new hardware and capabilities and
lots more debugging functionality to handle it when things aren't
working well.
- xhci driver updates
- new USB-serial device updates
- typec driver updates, including a chrome platform driver (acked by
the subsystem maintainers)
- other small driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ5fI8A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloPwCguHSvL8FM6Xwaxc/hdfalwI4c49AAnRECaMhR
mA1owvXgrKO3hjDHo2Sg
=Z5yt
-----END PGP SIGNATURE-----
Merge tag 'usb-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the USB and Thunderbolt driver updates for 6.14-rc1. Nothing
huge in here, just lots of new hardware support and updates for
existing drivers. Changes here are:
- big gadget f_tcm driver update
- other gadget driver updates and fixes
- thunderbolt driver updates for new hardware and capabilities and
lots more debugging functionality to handle it when things aren't
working well.
- xhci driver updates
- new USB-serial device updates
- typec driver updates, including a chrome platform driver (acked by
the subsystem maintainers)
- other small driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (123 commits)
usb: hcd: Bump local buffer size in rh_string()
Revert "usb: gadget: u_serial: Disable ep before setting port to null to fix the crash caused by port being null"
usb: typec: tcpci: Prevent Sink disconnection before vPpsShutdown in SPR PPS
usb: xhci: tegra: Fix OF boolean read warning
usb: host: xhci-plat: add support compatible ID PNP0D15
usb: typec: ucsi: Add a macro definition for UCSI v1.0
usb: dwc3: core: Defer the probe until USB power supply ready
usbip: Correct format specifier for seqnum from %d to %u
usbip: Fix seqnum sign extension issue in vhci_tx_urb
dt-bindings: usb: snps,dwc3: Split core description
usb: quirks: Add NO_LPM quirk for TOSHIBA TransMemory-Mx device
usb: dwc3: gadget: Reinitiate stream for all host NoStream behavior
USB: Use str_enable_disable-like helpers
USB: gadget: Use str_enable_disable-like helpers
USB: phy: Use str_enable_disable-like helpers
USB: typec: Use str_enable_disable-like helpers
USB: host: Use str_enable_disable-like helpers
USB: Replace own str_plural with common one
USB: serial: quatech2: fix null-ptr-deref in qt2_process_read_urb()
usb: phy: Remove API devm_usb_put_phy()
...
Updates to the usual drivers (ufs, lpfc, fnic, qla2xx, mpi3mr) The
major core change is the renaming of the slave_ methods plus a bit of
constification. The rest are minor updates and fixes.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZ5ZQKSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQMdAQCyVlDZ
v/3EFCuC4U1l70mMu8t+F4RPvqYxM3QPCi5dDQEA751YN/kaqxeXZDqGUKCAOE3K
Nl4XFTfLEkDVrQFFqPc=
=9sV8
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, fnic, qla2xx, mpi3mr).
The major core change is the renaming of the slave_ methods plus a bit
of constification. The rest are minor updates and fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (103 commits)
scsi: fnic: Propagate SCSI error code from fnic_scsi_drv_init()
scsi: fnic: Test for memory allocation failure and return error code
scsi: fnic: Return appropriate error code from failure of scsi drv init
scsi: fnic: Return appropriate error code for mem alloc failure
scsi: fnic: Remove always-true IS_FNIC_FCP_INITIATOR macro
scsi: fnic: Fix use of uninitialized value in debug message
scsi: fnic: Delete incorrect debugfs error handling
scsi: fnic: Remove unnecessary else to fix warning in FDLS FIP
scsi: fnic: Remove extern definition from .c files
scsi: fnic: Remove unnecessary else and unnecessary break in FDLS
scsi: mpi3mr: Fix possible crash when setting up bsg fails
scsi: ufs: bsg: Set bsg_queue to NULL after removal
scsi: ufs: bsg: Delete bsg_dev when setting up bsg fails
scsi: st: Don't set pos_unknown just after device recognition
scsi: aic7xxx: Fix build 'aicasm' warning
scsi: Revert "scsi: ufs: core: Probe for EXT_IID support"
scsi: storvsc: Ratelimit warning logs to prevent VM denial of service
scsi: scsi_debug: Constify sdebug_driver_template
scsi: documentation: Corrections for struct updates
scsi: driver-api: documentation: Change what is added to docbook
...
- Use usleep_range() instead of msleep() in acpi_os_sleep() to reduce
excessive delays due to timer inaccuracy, mostly affecting system
suspend and resume (Rafael Wysocki).
- Use str_enabled_disabled() string helpers in the ACPI tables parsing
code to make it easier to follow (Sunil V L).
- Update device properties parsing on systems using ACPI so that
data firmware nodes resulting from _DSD evaluation are treated
as available in firmware nodes walks (Sakari Ailus).
- Fix missing guid_t declaration in linux/prmt.h (Robert Richter).
- Update the GHES handling code to follow the global panic= policy
instead of overriding it by force-rebooting the system after a
fatal HW error has been reported (Borislav Petkov).
- Update messages printed by the ACPI battery driver to always
refer to driver extensions as "hooks" to avoid confusion with
similar functionality in the power supply subsystem in the
future (Thomas Weißschuh).
- Fix .probe() error path cleanup in the ACPI fan driver to avoid
memory leaks (Joe Hattori).
- Constify 'struct bin_attribute' in some places in the ACPI subsystem
and mark it as __ro_after_init in one place to prevent binary blob
attributes from being updated (Thomas Weißschuh)
- Add empty stubs for several ACPI-related symbols so that they can be
used when CONFIG_ACPI is unset and use them for removing unnecessary
conditional compilation from the ipu-bridge driver (Ricardo Ribalda).
-----BEGIN PGP SIGNATURE-----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=B/1O
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"The most significant change here is replacing msleep() in
acpi_os_sleep() with usleep_range() to reduce spurious sleep time due
to timer inaccuracy which may spectacularly reduce the duration of
system suspend and resume transitions on some systems.
All of the other changes fall into the fixes and cleanups category
this time.
Specifics:
- Use usleep_range() instead of msleep() in acpi_os_sleep() to reduce
excessive delays due to timer inaccuracy, mostly affecting system
suspend and resume (Rafael Wysocki)
- Use str_enabled_disabled() string helpers in the ACPI tables
parsing code to make it easier to follow (Sunil V L)
- Update device properties parsing on systems using ACPI so that data
firmware nodes resulting from _DSD evaluation are treated as
available in firmware nodes walks (Sakari Ailus)
- Fix missing guid_t declaration in linux/prmt.h (Robert Richter)
- Update the GHES handling code to follow the global panic= policy
instead of overriding it by force-rebooting the system after a
fatal HW error has been reported (Borislav Petkov)
- Update messages printed by the ACPI battery driver to always refer
to driver extensions as "hooks" to avoid confusion with similar
functionality in the power supply subsystem in the future (Thomas
Weißschuh)
- Fix .probe() error path cleanup in the ACPI fan driver to avoid
memory leaks (Joe Hattori)
- Constify 'struct bin_attribute' in some places in the ACPI
subsystem and mark it as __ro_after_init in one place to prevent
binary blob attributes from being updated (Thomas Weißschuh)
- Add empty stubs for several ACPI-related symbols so that they can
be used when CONFIG_ACPI is unset and use them for removing
unnecessary conditional compilation from the ipu-bridge driver
(Ricardo Ribalda)"
* tag 'acpi-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
APEI: GHES: Have GHES honor the panic= setting
ACPI: PRM: Fix missing guid_t declaration in linux/prmt.h
ACPI: tables: Use string choice helpers
ACPI: property: Consider data nodes as being available
media: ipu-bridge: Remove unneeded conditional compilations
ACPI: bus: implement acpi_device_hid when !ACPI
ACPI: bus: implement for_each_acpi_consumer_dev when !ACPI
ACPI: header: implement acpi_device_handle when !ACPI
ACPI: bus: implement acpi_get_physical_device_location when !ACPI
ACPI: bus: implement for_each_acpi_dev_match when !ACPI
ACPI: bus: change the prototype for acpi_get_physical_device_location
ACPI: fan: cleanup resources in the error path of .probe()
ACPI: battery: Rename extensions to hook in messages
ACPI: OSL: Use usleep_range() in acpi_os_sleep()
ACPI: sysfs: Constify 'struct bin_attribute'
ACPI: BGRT: Constify 'struct bin_attribute'
ACPI: BGRT: Mark bin_attribute as __ro_after_init
1) Per-CPU kthreads must stay affine to a single CPU and never execute
relevant code on any other CPU. This is currently handled by smpboot
code which takes care of CPU-hotplug operations. Affinity here is
a correctness constraint.
2) Some kthreads _have_ to be affine to a specific set of CPUs and can't
run anywhere else. The affinity is set through kthread_bind_mask()
and the subsystem takes care by itself to handle CPU-hotplug
operations. Affinity here is assumed to be a correctness constraint.
3) Per-node kthreads _prefer_ to be affine to a specific NUMA node. This
is not a correctness constraint but merely a preference in terms of
memory locality. kswapd and kcompactd both fall into this category.
The affinity is set manually like for any other task and CPU-hotplug
is supposed to be handled by the relevant subsystem so that the task
is properly reaffined whenever a given CPU from the node comes up.
Also care should be taken so that the node affinity doesn't cross
isolated (nohz_full) cpumask boundaries.
4) Similar to the previous point except kthreads have a _preferred_
affinity different than a node. Both RCU boost kthreads and RCU
exp kworkers fall into this category as they refer to "RCU nodes"
from a distinctly distributed tree.
Currently the preferred affinity patterns (3 and 4) have at least 4
identified users, with more or less success when it comes to handle
CPU-hotplug operations and CPU isolation. Each of which do it in its own
ad-hoc way.
This is an infrastructure proposal to handle this with the following API
changes:
_ kthread_create_on_node() automatically affines the created kthread to
its target node unless it has been set as per-cpu or bound with
kthread_bind[_mask]() before the first wake-up.
- kthread_affine_preferred() is a new function that can be called right
after kthread_create_on_node() to specify a preferred affinity
different than the specified node.
When the preferred affinity can't be applied because the possible
targets are offline or isolated (nohz_full), the kthread is affine
to the housekeeping CPUs (which means to all online CPUs most of the
time or only the non-nohz_full CPUs when nohz_full= is set).
kswapd, kcompactd, RCU boost kthreads and RCU exp kworkers have been
converted, along with a few old drivers.
Summary of the changes:
* Consolidate a bunch of ad-hoc implementations of kthread_run_on_cpu()
* Introduce task_cpu_fallback_mask() that defines the default last
resort affinity of a task to become nohz_full aware
* Add some correctness check to ensure kthread_bind() is always called
before the first kthread wake up.
* Default affine kthread to its preferred node.
* Convert kswapd / kcompactd and remove their halfway working ad-hoc
affinity implementation
* Implement kthreads preferred affinity
* Unify kthread worker and kthread API's style
* Convert RCU kthreads to the new API and remove the ad-hoc affinity
implementation.
-----BEGIN PGP SIGNATURE-----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=g8In
-----END PGP SIGNATURE-----
Merge tag 'kthread-for-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks
Pull kthread updates from Frederic Weisbecker:
"Kthreads affinity follow either of 4 existing different patterns:
1) Per-CPU kthreads must stay affine to a single CPU and never
execute relevant code on any other CPU. This is currently handled
by smpboot code which takes care of CPU-hotplug operations.
Affinity here is a correctness constraint.
2) Some kthreads _have_ to be affine to a specific set of CPUs and
can't run anywhere else. The affinity is set through
kthread_bind_mask() and the subsystem takes care by itself to
handle CPU-hotplug operations. Affinity here is assumed to be a
correctness constraint.
3) Per-node kthreads _prefer_ to be affine to a specific NUMA node.
This is not a correctness constraint but merely a preference in
terms of memory locality. kswapd and kcompactd both fall into this
category. The affinity is set manually like for any other task and
CPU-hotplug is supposed to be handled by the relevant subsystem so
that the task is properly reaffined whenever a given CPU from the
node comes up. Also care should be taken so that the node affinity
doesn't cross isolated (nohz_full) cpumask boundaries.
4) Similar to the previous point except kthreads have a _preferred_
affinity different than a node. Both RCU boost kthreads and RCU
exp kworkers fall into this category as they refer to "RCU nodes"
from a distinctly distributed tree.
Currently the preferred affinity patterns (3 and 4) have at least 4
identified users, with more or less success when it comes to handle
CPU-hotplug operations and CPU isolation. Each of which do it in its
own ad-hoc way.
This is an infrastructure proposal to handle this with the following
API changes:
- kthread_create_on_node() automatically affines the created kthread
to its target node unless it has been set as per-cpu or bound with
kthread_bind[_mask]() before the first wake-up.
- kthread_affine_preferred() is a new function that can be called
right after kthread_create_on_node() to specify a preferred
affinity different than the specified node.
When the preferred affinity can't be applied because the possible
targets are offline or isolated (nohz_full), the kthread is affine to
the housekeeping CPUs (which means to all online CPUs most of the time
or only the non-nohz_full CPUs when nohz_full= is set).
kswapd, kcompactd, RCU boost kthreads and RCU exp kworkers have been
converted, along with a few old drivers.
Summary of the changes:
- Consolidate a bunch of ad-hoc implementations of
kthread_run_on_cpu()
- Introduce task_cpu_fallback_mask() that defines the default last
resort affinity of a task to become nohz_full aware
- Add some correctness check to ensure kthread_bind() is always
called before the first kthread wake up.
- Default affine kthread to its preferred node.
- Convert kswapd / kcompactd and remove their halfway working ad-hoc
affinity implementation
- Implement kthreads preferred affinity
- Unify kthread worker and kthread API's style
- Convert RCU kthreads to the new API and remove the ad-hoc affinity
implementation"
* tag 'kthread-for-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks:
kthread: modify kernel-doc function name to match code
rcu: Use kthread preferred affinity for RCU exp kworkers
treewide: Introduce kthread_run_worker[_on_cpu]()
kthread: Unify kthread_create_on_cpu() and kthread_create_worker_on_cpu() automatic format
rcu: Use kthread preferred affinity for RCU boost
kthread: Implement preferred affinity
mm: Create/affine kswapd to its preferred node
mm: Create/affine kcompactd to its preferred node
kthread: Default affine kthread to its preferred NUMA node
kthread: Make sure kthread hasn't started while binding it
sched,arm64: Handle CPU isolation on last resort fallback rq selection
arm64: Exclude nohz_full CPUs from 32bits el0 support
lib: test_objpool: Use kthread_run_on_cpu()
kallsyms: Use kthread_run_on_cpu()
soc/qman: test: Use kthread_run_on_cpu()
arm/bL_switcher: Use kthread_run_on_cpu()
-----BEGIN PGP SIGNATURE-----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=EXYs
-----END PGP SIGNATURE-----
Merge tag 'for-6.14/block-20250118' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe pull requests via Keith:
- Target support for PCI-Endpoint transport (Damien)
- TCP IO queue spreading fixes (Sagi, Chaitanya)
- Target handling for "limited retry" flags (Guixen)
- Poll type fix (Yongsoo)
- Xarray storage error handling (Keisuke)
- Host memory buffer free size fix on error (Francis)
- MD pull requests via Song:
- Reintroduce md-linear (Yu Kuai)
- md-bitmap refactor and fix (Yu Kuai)
- Replace kmap_atomic with kmap_local_page (David Reaver)
- Quite a few queue freeze and debugfs deadlock fixes
Ming introduced lockdep support for this in the 6.13 kernel, and it
has (unsurprisingly) uncovered quite a few issues
- Use const attributes for IO schedulers
- Remove bio ioprio wrappers
- Fixes for stacked device atomic write support
- Refactor queue affinity helpers, in preparation for better supporting
isolated CPUs
- Cleanups of loop O_DIRECT handling
- Cleanup of BLK_MQ_F_* flags
- Add rotational support for null_blk
- Various fixes and cleanups
* tag 'for-6.14/block-20250118' of git://git.kernel.dk/linux: (106 commits)
block: Don't trim an atomic write
block: Add common atomic writes enable flag
md/md-linear: Fix a NULL vs IS_ERR() bug in linear_add()
block: limit disk max sectors to (LLONG_MAX >> 9)
block: Change blk_stack_atomic_writes_limits() unit_min check
block: Ensure start sector is aligned for stacking atomic writes
blk-mq: Move more error handling into blk_mq_submit_bio()
block: Reorder the request allocation code in blk_mq_submit_bio()
nvme: fix bogus kzalloc() return check in nvme_init_effects_log()
md/md-bitmap: move bitmap_{start, end}write to md upper layer
md/raid5: implement pers->bitmap_sector()
md: add a new callback pers->bitmap_sector()
md/md-bitmap: remove the last parameter for bimtap_ops->endwrite()
md/md-bitmap: factor behind write counters out from bitmap_{start/end}write()
md: Replace deprecated kmap_atomic() with kmap_local_page()
md: reintroduce md-linear
partitions: ldm: remove the initial kernel-doc notation
blk-cgroup: rwstat: fix kernel-doc warnings in header file
blk-cgroup: fix kernel-doc warnings in header file
nbd: fix partial sending
...
Merge ACPI battery and fan drivers updates and miscellaneous ACPI
chanages for 6.14:
- Update messages printed by the ACPI battery driver to always
refer to driver extensions as "hooks" to avoid confusion with
similar functionality in the power supply subsystem in the
future (Thomas Weißschuh).
- Fix .probe() error path cleanup in the ACPI fan driver to avoid
memory leaks (Joe Hattori).
- Constify 'struct bin_attribute' in some places in the ACPI subsystem
and mark it as __ro_after_init in one place to prevent binary blob
attributes from being updated (Thomas Weißschuh)
- Add empty stubs for several ACPI-related symbols so that they can be
used when CONFIG_ACPI is unset and use them for removing unnecessary
conditional compilation from the ipu-bridge driver (Ricardo Ribalda).
* acpi-battery:
ACPI: battery: Rename extensions to hook in messages
* acpi-fan:
ACPI: fan: cleanup resources in the error path of .probe()
* acpi-misc:
media: ipu-bridge: Remove unneeded conditional compilations
ACPI: bus: implement acpi_device_hid when !ACPI
ACPI: bus: implement for_each_acpi_consumer_dev when !ACPI
ACPI: header: implement acpi_device_handle when !ACPI
ACPI: bus: implement acpi_get_physical_device_location when !ACPI
ACPI: bus: implement for_each_acpi_dev_match when !ACPI
ACPI: bus: change the prototype for acpi_get_physical_device_location
ACPI: sysfs: Constify 'struct bin_attribute'
ACPI: BGRT: Constify 'struct bin_attribute'
ACPI: BGRT: Mark bin_attribute as __ro_after_init
GCC is not happy about the buffer size:
drivers/usb/core/hcd.c:441:48: error: ‘%s’ directive output may be truncated writing up to 64 bytes into a region of size between 35 and 99 [-Werror=format-truncation=]
441 | snprintf (buf, sizeof buf, "%s %s %s", init_utsname()->sysname,
| ^~
442 | init_utsname()->release, hcd->driver->description);
| ~~~~~~~~~~~~~~~~~~~~~~~
Bump the size to get it enough for the possible strings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250116160543.216913-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Source can drop its output voltage to the minimum of the requested
PPS APDO voltage range when it is in Current Limit Mode. If this voltage
falls within the range of vPpsShutdown, the Source initiates a Hard
Reset and discharges Vbus. However, currently the Sink may disconnect
before the voltage reaches vPpsShutdown, leading to unexpected behavior.
Prevent premature disconnection by setting the Sink's disconnect
threshold to the minimum vPpsShutdown value. Additionally, consider the
voltage drop due to IR drop when calculating the appropriate threshold.
This ensures a robust and reliable interaction between the Source and
Sink during SPR PPS Current Limit Mode operation.
Fixes: 4288debeaa ("usb: typec: tcpci: Fix up sink disconnect thresholds for PD")
Cc: stable <stable@kernel.org>
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250114142435.2093857-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit c141ecc3ce ("of: Warn when of_property_read_bool() is
used on non-boolean properties") was added, the following warning is
observed for the Tegra XHCI driver ...
OF: /bus@0/usb@3610000: Read of boolean property 'power-domains' with
a value.
Previously, of_property_read_bool() was used to determine if a property
was present but has now been replaced by of_property_present(). The
warning is meant to prevent new users but this user existed before the
change was made. Fix this by updating the Tegra XHCI driver to use
of_property_present() function to determine if the 'power-domains'
property is present.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20250116153829.477360-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support compatible ID PNP0D15 which declare that the xHCI
controller doesn't support standard debug capability.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20250116125141.25856-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many platforms from Qualcomm(before X elite) still use UCSI v1.0,
part of them hardcoded the version number to dsdt, add this for them.
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250113175131.590683-1-mitltlatltl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, DWC3 driver attempts to acquire the USB power supply only
once during the probe. If the USB power supply is not ready at that
time, the driver simply ignores the failure and continues the probe,
leading to permanent non-functioning of the gadget vbus_draw callback.
Address this problem by delaying the dwc3 driver initialization until
the USB power supply is registered.
Fixes: 6f0764b5ad ("usb: dwc3: add a power supply for current control")
Cc: stable <stable@kernel.org>
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250115044548.2701138-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The seqnum field in USBIP protocol is an unsigned value.
So we fix the format specifier from %d to %u to correctly
display the value.
Signed-off-by: Xiong Nandi <xndchn@gmail.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20241231161539.20192-3-xndchn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The atomic_inc_return function returns an int, while priv->seqnum is an
unsigned long. So we must cast the result to u32 to prevent potential
sign extension and size mismatch issues.
Signed-off-by: Xiong Nandi <xndchn@gmail.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20241231161539.20192-2-xndchn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 6.14-rc1, including:
- fix a long-standing NULL-deref issue in quatech2
- add support for hardware flow control to ch341
Included is also a related clean up.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZ4oQHgAKCRALxc3C7H1l
CCEJAQDUWUamPwhyoeqzb1xO93Sbym6TTXSP+WlZqoBxrEAAJQD/ZnF5l0JxYmmO
DJ8UX5IF/H66psT0gBcjlbYoVC3UkQE=
=uRTH
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.14-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Merge usb-serial updates from Johan:
USB-serial updates for 6.14-rc1
Here are the USB-serial updates for 6.14-rc1, including:
- fix a long-standing NULL-deref issue in quatech2
- add support for hardware flow control to ch341
Included is also a related clean up.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.14-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: quatech2: fix null-ptr-deref in qt2_process_read_urb()
USB: serial: ch341: use fix-width types consistently
USB: serial: ch341: add hardware flow control RTS/CTS
TOSHIBA TransMemory-Mx is a good performence flash device, but it
doesn't work well with LPM on Huawei hisi platform, so let's disable
LPM to resolve the issue.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Link: https://lore.kernel.org/r/20250113085619.44371-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are too many different host behaviors when it comes to NoStream
handling, and not everyone follows the USB and xHCI spec. The DWC3
driver attempts to do some guess work to interop with different hosts,
but it can't cover everything. Let's keep it simple and treat every host
the same: just retry on NoStream after a 100ms of no response delay.
Note that some hosts cannot handle frequent retries. This may affect
performance on certain defective hosts, but NoStream is a rare
occurrence and interoperability is more important.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/b92ae94c86f01f165d5f178b7767898573b6dc75.1736819308.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-6-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-5-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-4-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-3-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-2-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses a null-ptr-deref in qt2_process_read_urb() due to
an incorrect bounds check in the following:
if (newport > serial->num_ports) {
dev_err(&port->dev,
"%s - port change to invalid port: %i\n",
__func__, newport);
break;
}
The condition doesn't account for the valid range of the serial->port
buffer, which is from 0 to serial->num_ports - 1. When newport is equal
to serial->num_ports, the assignment of "port" in the
following code is out-of-bounds and NULL:
serial_priv->current_port = newport;
port = serial->port[serial_priv->current_port];
The fix checks if newport is greater than or equal to serial->num_ports
indicating it is out-of-bounds.
Reported-by: syzbot <syzbot+506479ebf12fe435d01a@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=506479ebf12fe435d01a
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Cc: <stable@vger.kernel.org> # 3.5
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
We need the debugfs / driver-core fixes in here as well for testing and
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Static devm_usb_phy_match() is only called by API devm_usb_put_phy(), and
the API has no caller now.
Remove the API and the static function.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250112-remove_api-v1-1-49cc8f792ac9@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As PD2.0 spec ("8.3.3.2.3 PE_SRC_Send_Capabilities state"), after the
Source receives the GoodCRC Message from the Sink in response to the
Source_Capabilities message, it should start the SenderResponseTimer,
after the timer times out, the state machine transitions to the
HARD_RESET state.
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Signed-off-by: Jos Wang <joswang@lenovo.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250105135245.7493-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When inserting a USB device, examining hcd->rsrc_start can be
helpful in identifying which hcd is mounted, as the physical
address represented here is typically unique.
The following code snippet demonstrates this:
struct usb_hcd *hcd = bus_to_hcd(udev->bus);
unsigned long long usb_hcd_addr = (unsigned long long)hcd->rsrc_start;
However, this approach has limitations now. For USB hosts with an
MMIO interface, the effectiveness of this method is restricted to
USB 2.0.
Because commit 3429e91a66 ("usb: host: xhci: add platform driver
support") assigned res->start to hcd->rsrc_start. But
shared_hcd->rsrc_start remains unassigned, which is also necessary
in certain scenarios.
Fixes: 3429e91a66 ("usb: host: xhci: add platform driver support")
Co-developed-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://lore.kernel.org/r/186B9F56972457B4+20250107133854.172309-1-wangyuli@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 533561a8aa ("usb: dwc3: omap: Use
devm_regulator_get_optional()") assumed NULL was returned, but
devm_regulator_get_optional() returns -ENODEV rather than NULL like
other *_get_optional() functions.
Fixes: 533561a8aa ("usb: dwc3: omap: Use devm_regulator_get_optional()")
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250109170748.3852439-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based kernel configuration guards.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250109152055.52931-1-rgallaispou@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the system begins to enter suspend mode, dwc3_suspend() is called
by PM suspend. There is a problem that if someone interrupt the system
suspend process between dwc3_suspend() and pm_suspend() of its parent
device, PM suspend will be canceled and attempt to resume suspended
devices so that dwc3_resume() will be called. However, dwc3 and its
parent device (like the power domain or glue driver) may already be
suspended by runtime PM in fact. If this sutiation happened, the
pm_runtime_set_active() in dwc3_resume() will return an error since
parent device was suspended. This can lead to unexpected behavior if
DWC3 proceeds to execute dwc3_resume_common().
EX.
RPM suspend: ... -> dwc3_runtime_suspend()
-> rpm_suspend() of parent device
...
PM suspend: ... -> dwc3_suspend() -> pm_suspend of parent device
^ interrupt, so resume suspended device
... <- dwc3_resume() <-/
^ pm_runtime_set_active() returns error
To prevent the problem, this commit will skip dwc3_resume_common() and
return the error if pm_runtime_set_active() fails.
Fixes: 68c26fe581 ("usb: dwc3: set pm runtime active before resume common")
Cc: stable <stable@kernel.org>
Signed-off-by: Ray Chi <raychi@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250106082240.3822059-1-raychi@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure isn't used outside this file and can be marked const so
that it gets moved to read-only memory.
Cc: Pavan Holla <pholla@chromium.org>
Cc: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Cc: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Łukasz Bartosik <ukaszb@chromium.org>
Link: https://lore.kernel.org/r/20250109220655.1677506-3-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Match the locking order used by the core block code by only freezing
the queue after taking the limits lock using the
queue_limits_commit_update_frozen helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20250110054726.1499538-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Here are some new modem and cp210x device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZ4EjZAAKCRALxc3C7H1l
CESsAQDHu+J6v93wA+pC62aKYY3kYaf7tRFI8sL+TyoG3GJnLwD/enxl0eg8JBsT
fBejnDz1KG8xcspkaAvoMHOfii2Qhww=
=0r69
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.13-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.13-rc7
Here are some new modem and cp210x device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.13-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Neoway N723-EA support
USB: serial: option: add MeiG Smart SRM815
USB: serial: cp210x: add Phoenix Contact UPS Device
kthread_create() creates a kthread without running it yet. kthread_run()
creates a kthread and runs it.
On the other hand, kthread_create_worker() creates a kthread worker and
runs it.
This difference in behaviours is confusing. Also there is no way to
create a kthread worker and affine it using kthread_bind_mask() or
kthread_affine_preferred() before starting it.
Consolidate the behaviours and introduce kthread_run_worker[_on_cpu]()
that behaves just like kthread_run(). kthread_create_worker[_on_cpu]()
will now only create a kthread worker without starting it.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Use Linux fix-width types consistently and drop a related unnecessary
cast.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds support for enabling and disabling RTS/CTS hardware flow
control.
Tested using CH341A and CH340E.
Fixes part of the following bug report:
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197109
Signed-off-by: Lode Willems <me@lodewillems.com>
[ johan: prepare index argument once, drop casts ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The error handling for the case `con_index == 0` should involve dropping
the pm usage counter, as ucsi_ccg_sync_control() gets it at the
beginning. Fix it.
Cc: stable <stable@kernel.org>
Fixes: e56aac6e5a ("usb: typec: fix potential array underflow in ucsi_ccg_sync_control()")
Signed-off-by: GONG Ruiqi <gongruiqi1@huawei.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250107015750.2778646-1-gongruiqi1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes data corruption when accessing the internal SD card in mass
storage mode.
I am actually not too sure why. I didn't figure a straightforward way to
reproduce the issue, but i seem to get garbage when issuing a lot (over 50)
of large reads (over 120 sectors) are done in a quick succession. That is,
time seems to matter here -- larger reads are fine if they are done with
some delay between them.
But I'm not great at understanding this sort of things, so I'll assume
the issue other, smarter, folks were seeing with similar phones is the
same problem and I'll just put my quirk next to theirs.
The "Software details" screen on the phone is as follows:
V 04.06
07-08-13
RM-849
(c) Nokia
TL;DR version of the device descriptor:
idVendor 0x0421 Nokia Mobile Phones
idProduct 0x06c2
bcdDevice 4.06
iManufacturer 1 Nokia
iProduct 2 Nokia 208
The patch assumes older firmwares are broken too (I'm unable to test, but
no biggie if they aren't I guess), and I have no idea if newer firmware
exists.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250101212206.2386207-1-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should do reverse selection of other components from
CONFIG_USB_F_MIDI2 which is tristate, instead of
CONFIG_USB_CONFIGFS_F_MIDI2 which is bool, for satisfying subtle
module dependencies.
Fixes: 8b645922b2 ("usb: gadget: Add support for USB MIDI 2.0 function driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20250101131124.27599-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cable_match(), as matching function of device_find_child(), matches
a device with device type @typec_cable_dev_type, and its task can be
simplified by the recently introduced API device_match_type().
partner_match() is similar with cable_match() but with a different
device type @typec_partner_dev_type.
Remove both functions and use the API plus respective device type instead.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241224-const_dfc_done-v5-12-6623037414d4@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Constify the following API:
struct device *device_find_child(struct device *dev, void *data,
int (*match)(struct device *dev, void *data));
To :
struct device *device_find_child(struct device *dev, const void *data,
device_match_t match);
typedef int (*device_match_t)(struct device *dev, const void *data);
with the following reasons:
- Protect caller's match data @*data which is for comparison and lookup
and the API does not actually need to modify @*data.
- Make the API's parameters (@match)() and @data have the same type as
all of other device finding APIs (bus|class|driver)_find_device().
- All kinds of existing device match functions can be directly taken
as the API's argument, they were exported by driver core.
Constify the API and adapt for various existing usages.
BTW, various subsystem changes are squashed into this commit to meet
'git bisect' requirement, and this commit has the minimal and simplest
changes to complement squashing shortcoming, and that may bring extra
code improvement.
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Uwe Kleine-König <ukleinek@kernel.org> # for drivers/pwm
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20241224-const_dfc_done-v5-4-6623037414d4@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implementation of a UCSI transport driver for ChromeOS.
This driver will be loaded if the ChromeOS EC implements a PPM.
Signed-off-by: Pavan Holla <pholla@chromium.org>
Co-developed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Co-developed-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Łukasz Bartosik <ukaszb@chromium.org>
Link: https://lore.kernel.org/r/20241231131047.1757434-3-ukaszb@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'vbus-supply' regulator is optional, so use
devm_regulator_get_optional() instead of checking for property presence
first.
While here, rework the error handling to use dev_err_probe() which
handles deferred probe correctly without an error message.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241231164456.262581-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC hosts can pass 24 bits of data with a command completion event TRB
as the completion code only uses 8 bits of the 32 bit status field.
Only Configure Endpoint, and Get Extended Property commands utilize
this "command completion parameter" 24 bit field.
For other command completion events the xHC should keep it RsvdZ.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a command is queued to the final usable TRB of a ring segment, the
enqueue pointer is advanced to the subsequent link TRB and no further.
If the command is later aborted, when the abort completion is handled
the dequeue pointer is advanced to the first TRB of the next segment.
If no further commands are queued, xhci_handle_stopped_cmd_ring() sees
the ring pointers unequal and assumes that there is a pending command,
so it calls xhci_mod_cmd_timer() which crashes if cur_cmd was NULL.
Don't attempt timer setup if cur_cmd is NULL. The subsequent doorbell
ring likely is unnecessary too, but it's harmless. Leave it alone.
This is probably Bug 219532, but no confirmation has been received.
The issue has been independently reproduced and confirmed fixed using
a USB MCU programmed to NAK the Status stage of SET_ADDRESS forever.
Everything continued working normally after several prevented crashes.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219532
Fixes: c311e391a7 ("xhci: rework command timeout and cancellation,")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve dbc transfer rate performance by copying the received data to
the tty buffer directly in the request complete callback function if
possible.
Only defer it in case there is already pending deferred work, tty is
throttled, or we fail copy the data to the tty buffer
The request complete callback is already called by a workqueue.
This is part 3/3 of a dbc performance improvement series that roughly
triples dbc performace when using adb push and pull over dbc.
Max/min push rate after patches is 210/118 MB/s, pull rate 171/133 MB/s,
tested with large files (300MB-9GB) by Łukasz Bartosik
Cc: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Queue event polling work with 0 delay in case there are pending transfers
queued up. This is part 2 of a 3 part series that roughly triples dbc
performace when using adb push and pull over dbc.
Max/min push rate after patches is 210/118 MB/s, pull rate 171/133 MB/s,
tested with large files (300MB-9GB) by Łukasz Bartosik
First performance improvement patch was commit 31128e7492
("xhci: dbc: add dbgtty request to end of list once it completes")
Cc: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set TARGET_SCF_ACK_KREF flag and allow f_tcm to take the BOT command
reference. A usb request may be canceled, the f_tcm knows this. Let it
decides if the command should be freed. This is the same as how the UAS
interface is done.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/e791c639e91b5d91a8787f5d6902e8c58f1dc172.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle target_core_fabric_ops TASK MANAGEMENT functions and their
response. If a TASK MANAGEMENT command is received, the driver will
interpret the function TMF_*, translate to TMR_*, and fire off a command
work executing target_submit_tmr(). On completion, it will handle the
TASK MANAGEMENT response through uasp_send_tm_response().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/50339586e36509dadb9c208b3314530993e673b6.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the transfer is cancelled due to a disconnect or driver tear down
(error code -ESHUTDOWN), then just free the command. However, if it got
cancelled due to other reasons, then send a sense CHECK CONDITION status
with TCM_CHECK_CONDITION_ABORT_CMD status to host notifying the delivery
failure. Note that this is separate from TASK MANAGEMENT function abort
task command, which will require a separate response IU.
See UAS-r04 section 8.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f2ae293c1fc39df4d242a2f724584bf4ec105ece.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There may be different reasons for the transfer to be cancelled. Don't
blindly free the command without checking its status. We may still need
to properly respond to cancelled command. Check and only free the
command on endpoint disable.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/6c4ae2b4c2a9037bdcb6f909e173a94b11f04657.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't just wait for the data write completion and execute the target
command. We need to verify if the request completed successfully and not
just sending invalid data. The verification is done in the write request
completion routine. Queue the same work of the command to execute the
target_execute_cmd() on data write.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9f6b1c6946cf49eeba0173e405678b9b7786636b.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To properly respond to host sending more commands than the number of
streams the device advertises, the device needs to be able to reject the
command with a response. Allocate an extra request to handle 1 more
command than the number of streams.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/256f2ec8f5e042ab692d9593144fa75f3d3ce94b.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resubmit command on completion to fetch more commands and service them
in parallel. Increase the number of work in a queue. Each work will be
for each command allowing them to be processed concurrently. Also, set
them to be unbounded by cpu to improve performance.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/933cf7191b672bf4cfbea4df19af1b08dc1baca9.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can handle multiple commands concurently. Each command services a
stream id. At the moment, the driver will handle 32 outstanding streams,
which is equivalent to 32 commands. Make sure to allocate a matching
number of commands to the number of streams.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/2d806120dcc10c88fef21865b7bc1d2b6604fe42.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Host can assign stream ID value greater than number of streams
allocated. The tcm function needs to keep track of which stream is
available to assign the stream ID. This patch doesn't track that, but at
least it makes sure that there's no Oops if the host send tag with a
value greater than the number of supported streams.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d57b7dfd228199cef811206b1b83ec649f742752.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only allocate up to UASP_SS_EP_COMP_NUM_STREAMS number of session tags.
We should not be using more than UASP_SS_EP_COMP_NUM_STREAMS of tags due
to the number of commands limit we imposed. Each command uses a unique
tag. Any more than that is unnecessary. By limiting it, we can detect an
issue in our driver immediately should we run out of session tags.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/017016ffcab2f3c284d863fc42483b83dbd21b35.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the default bMaxBurst is 0. Set default bMaxBurst to 15 (i.e.
16 bursts) to Data IN and OUT endpoints to improve performance. It
should be fine for a controller that supports less than 16 bursts. It
should be able to negotiate properly with the host at packet level for
the end of burst.
If the controller can't handle a burst of 16, and high performance isn't
important, the user can use BOT protocol from mass_storage gadget driver
instead.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9d6265db4d138e542f281988362bc4392b034d43.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some old builds of Microsoft Windows 10 UASP class driver reject UASP
device with stream count of 2^4. To keep compatibility with both Linux
and Windows, let's increase the stream count to 2^5. Also, internal
tests show that stream count of 2^5 increases performance slightly.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/23bf7f5cb04da691fd6ba0a77babee9ad3195f44.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The active property of port altmode should be writable (to prevent or
allow partner altmodes from entering) and needs to be part of
typec_altmode_desc so we can initialize the port to an inactive state if
desired.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241213153543.v5.3.I794566684ab2965e209f326b08232006eff333f8@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mode in struct typec_altmode is used to indicate the index of the
altmode on a port, partner or plug. It is used in enter mode VDMs but
doesn't make much sense for matching against altmode drivers or for
matching partner to port altmodes.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241213153543.v5.1.Ie0d37646f18461234777d88b4c3e21faed92ed4f@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UDC state in sysfs (/sys/class/udc/<udc>/state) should accurately
reflect the current state of the USB Device Controller.
Currently, the UDC state is not handled consistently during gadget
disconnection. While the disconnect interrupt path correctly sets the
state to "not-attached", manual deconfiguration leaves the state in
"configured", misrepresenting the actual situation.
This commit ensures consistent UDC state handling by setting the state to
"not-attached" after manual deconfiguration. This accurately reflects the
UDC's state and provides a consistent behavior regardless of the
disconnection method.
Signed-off-by: Roy Luo <royluo@google.com>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Tested-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20241223042536.1465299-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241222-sysfs-const-bin_attr-usbip-v1-1-20d611a9bfa4@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241222-sysfs-const-bin_attr-usb-v1-1-19a137c0f20a@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes issue where memory will fail to be allocated for larger bulk
transfers, ~1 MB or more. This occurs because userland libraries, such
as libusb, send the entire USB data buffer when SG support is detected.
The assumption is that the driver knows how to properly split the data
up before sending it out.
By hardcoding a limit, bigger transfers that exceed the SG tablesize
limit of 32 will be unable to use SG. This results in an attempt to
allocate contiguous pages which, unsurprisingly, will fail too and
returns an ENOMEM. It looks like other drivers that support SG allow for
any length of SG lists. Accepting any SG size allows the driver to
properly handle large bulk transfer situations.
Tested bulk read and write operations using the following devices:
- Logitech Webcam Pro 9000 - USB 2.0
- SanDisk Ultra - USB 3.0
- Logitech M500s Mouse
Signed-off-by: Jason Long <jasonlongball@gmail.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20241218161344.202637-1-jasonlongball@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds a new AMS for responding to a "Get_Revision" request.
Revision message consists of the following fields:
+----------------------------------------------------+
| Header | RMDO |
| No. of data objects = 1 | |
+----------------------------------------------------+
While RMDO consists of:
* B31..28 Revision Major
* B27..24 Revision Minor
* B23..20 Version Major
* B19..16 Version Minor
* B15..0 Reserved, shall be set to zero.
As per the PD spec ("8.3.3.16.2.1 PR_Give_Revision State"), a request is
only expected when an explicit contract is established and the port is
in ready state. This AMS is only supported for PD >= 3.0.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20241210-get_rev_upstream-v2-3-d0094e52d48f@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for parsing "pd-revision" DT property in TCPM and store PD
revision and version supported by the Type-C connnector.
It should be noted that the PD revision is the maximum possible revision
supported by the port. This is different from the 2 bit revision set in
PD msg headers. The purpose of the 2 bit revision value is to negotiate
between Rev 2.X & 3.X spec rev as part of contract negotiation, while
this is used for Get_Revision AMS after a contract is in place.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20241210-get_rev_upstream-v2-2-d0094e52d48f@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TI HD3SS3220 Type-C controller supports configuring
its role preference when operating as a dual-role port
through the SOURCE_PREF field of the General Control Register.
The previous driver behavior was to set the role preference
based on the dr_set typec_operation.
However, the controller does not support swapping the data role
on an active connection due to its lack of Power Delivery support.
Remove previous dr_set typec_operation, and support setting
the role preference based on the corresponding fwnode property,
as well as the try_role typec_operation.
Signed-off-by: Oliver Facklam <oliver.facklam@zuehlke.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241211-usb-typec-controller-enhancements-v3-3-e4bc1b6e1441@zuehlke.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TI HD3SS3220 Type-C controller supports configuring the port type
it will operate as through the MODE_SELECT field of the General
Control Register.
Configure the port type based on the fwnode property "power-role"
during probe, if present. If the property is absent, leave the
operation mode at the default, which is defined by the PORT pin
of the chip.
Support configuring the port type through the port_type_set
typec_operation as well.
The MODE_SELECT field can only be changed when the controller is in
unattached state, so follow the sequence recommended by the datasheet to:
1. disable termination on CC pins to disable the controller
2. change the mode
3. re-enable termination
This will effectively cause a connected device to disconnect
for the duration of the mode change.
Signed-off-by: Oliver Facklam <oliver.facklam@zuehlke.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241211-usb-typec-controller-enhancements-v3-2-e4bc1b6e1441@zuehlke.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TI HD3SS3220 Type-C controller supports configuring its advertised
power operation mode over I2C using the CURRENT_MODE_ADVERTISE field
of the Connection Status Register.
Configure this power mode based on the existing (optional) property
"typec-power-opmode" of /schemas/connector/usb-connector.yaml
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Oliver Facklam <oliver.facklam@zuehlke.com>
Link: https://lore.kernel.org/r/20241211-usb-typec-controller-enhancements-v3-1-e4bc1b6e1441@zuehlke.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit addresses an issue related to below kernel panic where
panic_on_warn is enabled. It is caused by the unnecessary use of WARN_ON
in functionsfs_bind, which easily leads to the following scenarios.
1.adb_write in adbd 2. UDC write via configfs
================= =====================
->usb_ffs_open_thread() ->UDC write
->open_functionfs() ->configfs_write_iter()
->adb_open() ->gadget_dev_desc_UDC_store()
->adb_write() ->usb_gadget_register_driver_owner
->driver_register()
->StartMonitor() ->bus_add_driver()
->adb_read() ->gadget_bind_driver()
<times-out without BIND event> ->configfs_composite_bind()
->usb_add_function()
->open_functionfs() ->ffs_func_bind()
->adb_open() ->functionfs_bind()
<ffs->state !=FFS_ACTIVE>
The adb_open, adb_read, and adb_write operations are invoked from the
daemon, but trying to bind the function is a process that is invoked by
UDC write through configfs, which opens up the possibility of a race
condition between the two paths. In this race scenario, the kernel panic
occurs due to the WARN_ON from functionfs_bind when panic_on_warn is
enabled. This commit fixes the kernel panic by removing the unnecessary
WARN_ON.
Kernel panic - not syncing: kernel: panic_on_warn set ...
[ 14.542395] Call trace:
[ 14.542464] ffs_func_bind+0x1c8/0x14a8
[ 14.542468] usb_add_function+0xcc/0x1f0
[ 14.542473] configfs_composite_bind+0x468/0x588
[ 14.542478] gadget_bind_driver+0x108/0x27c
[ 14.542483] really_probe+0x190/0x374
[ 14.542488] __driver_probe_device+0xa0/0x12c
[ 14.542492] driver_probe_device+0x3c/0x220
[ 14.542498] __driver_attach+0x11c/0x1fc
[ 14.542502] bus_for_each_dev+0x104/0x160
[ 14.542506] driver_attach+0x24/0x34
[ 14.542510] bus_add_driver+0x154/0x270
[ 14.542514] driver_register+0x68/0x104
[ 14.542518] usb_gadget_register_driver_owner+0x48/0xf4
[ 14.542523] gadget_dev_desc_UDC_store+0xf8/0x144
[ 14.542526] configfs_write_iter+0xf0/0x138
Fixes: ddf8abd259 ("USB: f_fs: the FunctionFS driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Akash M <akash.m5@samsung.com>
Link: https://lore.kernel.org/r/20241219125221.1679-1-akash.m5@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's USB error when tegra board is shutting down:
[ 180.919315] usb 2-3: Failed to set U1 timeout to 0x0,error code -113
[ 180.919995] usb 2-3: Failed to set U1 timeout to 0xa,error code -113
[ 180.920512] usb 2-3: Failed to set U2 timeout to 0x4,error code -113
[ 186.157172] tegra-xusb 3610000.usb: xHCI host controller not responding, assume dead
[ 186.157858] tegra-xusb 3610000.usb: HC died; cleaning up
[ 186.317280] tegra-xusb 3610000.usb: Timeout while waiting for evaluate context command
The issue is caused by disabling LPM on already suspended ports.
For USB2 LPM, the LPM is already disabled during port suspend. For USB3
LPM, port won't transit to U1/U2 when it's already suspended in U3,
hence disabling LPM is only needed for ports that are not suspended.
Cc: Wayne Chang <waynec@nvidia.com>
Cc: stable <stable@kernel.org>
Fixes: d920a2ed86 ("usb: Disable USB3 LPM at shutdown")
Signed-off-by: Kai-Heng Feng <kaihengf@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20241206074817.89189-1-kaihengf@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When device_add(&udev->dev) succeeds and a later call fails,
usb_new_device() does not properly call device_del(). As comment of
device_add() says, 'if device_add() succeeds, you should call
device_del() when you want to get rid of it. If device_add() has not
succeeded, use only put_device() to drop the reference count'.
Found by code review.
Cc: stable <stable@kernel.org>
Fixes: 9f8b17e643 ("USB: make usbdevices export their device nodes instead of using a separate class")
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241218071346.2973980-1-make_ruc2021@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tcpci_irq() may meet below NULL pointer dereference issue:
[ 2.641851] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
[ 2.641951] status 0x1, 0x37f
[ 2.650659] Mem abort info:
[ 2.656490] ESR = 0x0000000096000004
[ 2.660230] EC = 0x25: DABT (current EL), IL = 32 bits
[ 2.665532] SET = 0, FnV = 0
[ 2.668579] EA = 0, S1PTW = 0
[ 2.671715] FSC = 0x04: level 0 translation fault
[ 2.676584] Data abort info:
[ 2.679459] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
[ 2.684936] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 2.689980] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 2.695284] [0000000000000010] user address but active_mm is swapper
[ 2.701632] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[ 2.707883] Modules linked in:
[ 2.710936] CPU: 1 UID: 0 PID: 87 Comm: irq/111-2-0051 Not tainted 6.12.0-rc6-06316-g7f63786ad3d1-dirty #4
[ 2.720570] Hardware name: NXP i.MX93 11X11 EVK board (DT)
[ 2.726040] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 2.732989] pc : tcpci_irq+0x38/0x318
[ 2.736647] lr : _tcpci_irq+0x14/0x20
[ 2.740295] sp : ffff80008324bd30
[ 2.743597] x29: ffff80008324bd70 x28: ffff800080107894 x27: ffff800082198f70
[ 2.750721] x26: ffff0000050e6680 x25: ffff000004d172ac x24: ffff0000050f0000
[ 2.757845] x23: ffff000004d17200 x22: 0000000000000001 x21: ffff0000050f0000
[ 2.764969] x20: ffff000004d17200 x19: 0000000000000000 x18: 0000000000000001
[ 2.772093] x17: 0000000000000000 x16: ffff80008183d8a0 x15: ffff00007fbab040
[ 2.779217] x14: ffff00007fb918c0 x13: 0000000000000000 x12: 000000000000017a
[ 2.786341] x11: 0000000000000001 x10: 0000000000000a90 x9 : ffff80008324bd00
[ 2.793465] x8 : ffff0000050f0af0 x7 : ffff00007fbaa840 x6 : 0000000000000031
[ 2.800589] x5 : 000000000000017a x4 : 0000000000000002 x3 : 0000000000000002
[ 2.807713] x2 : ffff80008324bd3a x1 : 0000000000000010 x0 : 0000000000000000
[ 2.814838] Call trace:
[ 2.817273] tcpci_irq+0x38/0x318
[ 2.820583] _tcpci_irq+0x14/0x20
[ 2.823885] irq_thread_fn+0x2c/0xa8
[ 2.827456] irq_thread+0x16c/0x2f4
[ 2.830940] kthread+0x110/0x114
[ 2.834164] ret_from_fork+0x10/0x20
[ 2.837738] Code: f9426420 f9001fe0 d2800000 52800201 (f9400a60)
This may happen on shared irq case. Such as two Type-C ports share one
irq. After the first port finished tcpci_register_port(), it may trigger
interrupt. However, if the interrupt comes by chance the 2nd port finishes
devm_request_threaded_irq(), the 2nd port interrupt handler will run at
first. Then the above issue happens due to tcpci is still a NULL pointer
in tcpci_irq() when dereference to regmap.
devm_request_threaded_irq()
<-- port1 irq comes
disable_irq(client->irq);
tcpci_register_port()
This will restore the logic to the state before commit (77e85107a7 "usb:
typec: tcpci: support edge irq").
However, moving tcpci_register_port() earlier creates a problem when use
edge irq because tcpci_init() will be called before
devm_request_threaded_irq(). The tcpci_init() writes the ALERT_MASK to
the hardware to tell it to start generating interrupts but we're not ready
to deal with them yet, then the ALERT events may be missed and ALERT line
will not recover to high level forever. To avoid the issue, this will also
set ALERT_MASK register after devm_request_threaded_irq() return.
Fixes: 77e85107a7 ("usb: typec: tcpci: support edge irq")
Cc: stable <stable@kernel.org>
Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20241218095328.2604607-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Considering that in some extreme cases, when performing the
unbinding operation, gserial_disconnect has cleared gser->ioport,
which triggers gadget reconfiguration, and then calls gs_read_complete,
resulting in access to a null pointer. Therefore, ep is disabled before
gserial_disconnect sets port to null to prevent this from happening.
Call trace:
gs_read_complete+0x58/0x240
usb_gadget_giveback_request+0x40/0x160
dwc3_remove_requests+0x170/0x484
dwc3_ep0_out_start+0xb0/0x1d4
__dwc3_gadget_start+0x25c/0x720
kretprobe_trampoline.cfi_jt+0x0/0x8
kretprobe_trampoline.cfi_jt+0x0/0x8
udc_bind_to_driver+0x1d8/0x300
usb_gadget_probe_driver+0xa8/0x1dc
gadget_dev_desc_UDC_store+0x13c/0x188
configfs_write_iter+0x160/0x1f4
vfs_write+0x2d0/0x40c
ksys_write+0x7c/0xf0
__arm64_sys_write+0x20/0x30
invoke_syscall+0x60/0x150
el0_svc_common+0x8c/0xf8
do_el0_svc+0x28/0xa0
el0_svc+0x24/0x84
Fixes: c1dca562be ("usb gadget: split out serial core")
Cc: stable <stable@kernel.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Link: https://lore.kernel.org/r/TYUPR06MB621733B5AC690DBDF80A0DCCD2042@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current implementation of ci_hdrc_imx_driver does not decrement the
refcount of the device obtained in usbmisc_get_init_data(). Add a
put_device() call in .remove() and in .probe() before returning an
error.
This bug was found by an experimental static analysis tool that I am
developing.
Cc: stable <stable@kernel.org>
Fixes: f40017e0f3 ("chipidea: usbmisc_imx: Add USB support for VF610 SoCs")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20241216015539.352579-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation of the ucsi glink client connector_status()
callback is only relying on the state of the gpio. This means that even
when the cable is unplugged, the orientation propagated to the switches
along the graph is "orientation normal", instead of "orientation none",
which would be the correct one in this case.
One of the Qualcomm DP-USB PHY combo drivers, which needs to be aware of
the orientation change, is relying on the "orientation none" to skip
the reinitialization of the entire PHY. Since the ucsi glink client
advertises "orientation normal" even when the cable is unplugged, the
mentioned PHY is taken down and reinitialized when in fact it should be
left as-is. This triggers a crash within the displayport controller driver
in turn, which brings the whole system down on some Qualcomm platforms.
Propagating "orientation none" from the ucsi glink client on the
connector_status() callback hides the problem of the mentioned PHY driver
away for now. But the "orientation none" is nonetheless the correct one
to be used in this case.
So propagate the "orientation none" instead when the connector status
flags says cable is disconnected.
Fixes: 76716fd5bf ("usb: typec: ucsi: glink: move GPIO reading into connector_status callback")
Cc: stable <stable@kernel.org> # 6.10
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241212-usb-typec-ucsi-glink-add-orientation-none-v2-1-db5a50498a77@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c033563220
("usb: gadget: configfs: Attach arbitrary strings to cdev")
a user can provide extra string descriptors to a USB gadget via configfs.
For "manufacturer", "product", "serialnumber", setting the string via
configfs ignores a trailing LF.
For the arbitrary strings the LF was not ignored.
This patch ignores a trailing LF to make this consistent with the existing
behavior for "manufacturer", ... string descriptors.
Fixes: c033563220 ("usb: gadget: configfs: Attach arbitrary strings to cdev")
Cc: stable <stable@kernel.org>
Signed-off-by: Ingo Rohloff <ingo.rohloff@lauterbach.com>
Link: https://lore.kernel.org/r/20241212154114.29295-1-ingo.rohloff@lauterbach.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the regression introduced by commit d8c6edfa3f ("USB:
usblp: don't call usb_set_interface if there's a single alt"),
which causes that unsupported protocols can also be set via
ioctl when the num_altsetting of the device is 1.
Move the check for protocol support to the earlier stage.
Fixes: d8c6edfa3f ("USB: usblp: don't call usb_set_interface if there's a single alt")
Cc: stable <stable@kernel.org>
Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
Link: https://lore.kernel.org/r/20241212143852.671889-1-jerrysteve1101@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently afunc_bind sets std_ac_if_desc.bNumEndpoints to 1 if
controls (mute/volume) are enabled. During next afunc_bind call,
bNumEndpoints would be unchanged and incorrectly set to 1 even
if the controls aren't enabled.
Fix this by resetting the value of bNumEndpoints to 0 on every
afunc_bind call.
Fixes: eaf6cbe099 ("usb: gadget: f_uac2: add volume and mute support")
Cc: stable <stable@kernel.org>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20241211115915.159864-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The source of quirk XHCI_SKIP_PHY_INIT comes from xhci_plat_priv.quirks or
software node property. This will set skip_phy_initialization if software
node also has XHCI_SKIP_PHY_INIT property.
Fixes: a6cd2b3fa8 ("usb: host: xhci-plat: Parse xhci-missing_cas_quirk and apply quirk")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20241209111423.4085548-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Runtime PM documentation (Section 5) mentions, during remove()
callbacks, drivers should undo the runtime PM changes done in
probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc. Hence add missing
function to disable autosuspend on dwc3-am62 driver unbind.
Fixes: e8784c0aec ("drivers: usb: dwc3: Add AM62 USB wrapper driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241209105728.3216872-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before writing a new value to the register, the old value needs to be
masked out for the new value to be programmed as intended, because at
least in some cases the reset value of that field is 0xf (max value).
At the moment, the dwc3 core initialises the threshold to the maximum
value (0xf), with the option to override it via a DT. No upstream DTs
seem to override it, therefore this commit doesn't change behaviour for
any upstream platform. Nevertheless, the code should be fixed to have
the desired outcome.
Do so.
Fixes: 80caf7d21a ("usb: dwc3: add lpm erratum support")
Cc: stable@vger.kernel.org # 5.10+ (needs adjustment for 5.4)
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241209-dwc3-nyet-fix-v2-1-02755683345b@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cc1 and cc2 status returned by tcpci_get_cc() may be TYPEC_CC_OPEN
or TYPEC_CC_RA. So don't assume it's just TYPEC_CC_RD or TYPEC_CC_RP_*.
This will let local port present Rd on CC only when cc1/cc2 status is
TYPEC_CC_RP_*.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241211105753.1205312-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If controller looses power during PM suspend then re-initialize
it. We use the DEBUG_CFG register to track if controller lost power
or was reset in PM suspend.
Move all initialization code into dwc3_ti_init() so it can be re-used.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241212-am62-dwc3-io-ddr-v3-1-10b95cd7e9c0@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds documentation for two USB functions:
- usb_otg_state_string(), which returns a human-readable name for OTG
states and
- usb_get_dr_mode_from_string(), which returns the dual role mode for a
given string.
Signed-off-by: Lucy Mielke <lucymielke@icloud.com>
Link: https://lore.kernel.org/r/6nvegfmo6d5ak4soaf5nyifsaasfts4qlsnnpsd4sgpnikc2jd@amfmgdr5n3bi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function pmc_mux_port_debugfs_init() the buffer for
the name of the port is limited to six bytes. That makes the
compiler think that the output of "port%d" may be truncated.
That can't actually happen as the interface can support
maximum of eight ports. To make the compiler happy just
increase the buffer to where the warning goes away.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412031437.vX580pxx-lkp@intel.com/
Cc: Rajat Khandelwal <rajat.khandelwal@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241205113919.1182673-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It generally is not OK to use acpi_status and/or AE_ error codes
without CONFIG_ACPI and they really only should be used in
drivers/acpi/ (and not everywhere in there for that matter).
So acpi_get_physical_device_location() needs to be redefined to return
something different from acpi_status (preferably bool) in order to be
used in !CONFIG_ACPI code.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://patch.msgid.link/20241216-fix-ipu-v5-1-3d6b35ddce7b@chromium.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The source and destination rings were incorrectly assigned during the ring
linking process. The "source" ring, which contains the new segments,
was not spliced into the "destination" ring, leading to incorrect ring
expansion.
Fixes: fe688e5006 ("usb: xhci: refactor xhci_link_rings() to use source and destination rings")
Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Closes: https://lore.kernel.org/lkml/CAAJw_ZtppNqC9XA=-WVQDr+vaAS=di7jo15CzSqONeX48H75MA@mail.gmail.com/
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241217102122.2316814-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC hosts from several vendors have the same issue where endpoints start
so slowly that a later queued 'Stop Endpoint' command may complete before
endpoint is up and running.
The 'Stop Endpoint' command fails with context state error as the endpoint
still appears as stopped.
See commit 42b7581376 ("usb: xhci: Limit Stop Endpoint retries") for
details
CC: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241217102122.2316814-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZ1vuXQAKCRALxc3C7H1l
CLJ0AQDSkSckl0A6kriR/xOSDWv2uIC+insL1LC5njr/JJrv7wD/WoRWIHEllqVN
JLdKbJ2Vim+2BG16DsW8/mpVldkaLAY=
=wuzL
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.13-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.13-rc3
Here are some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.13-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit FE910C04 rmnet compositions
USB: serial: option: add MediaTek T7XX compositions
USB: serial: option: add Netprisma LCUK54 modules for WWAN Ready
USB: serial: option: add MeiG Smart SLM770A
USB: serial: option: add TCL IK512 MBIM & ECM
Here are some small USB driver fixes for some reported issues. Included
in here are:
- typec driver bugfixes
- u_serial gadget driver bugfix for much reported and discussed issue
- dwc2 bugfixes
- midi gadget driver bugfix
- ehci-hcd driver bugfix
- other small bugfixes
All of these have been in linux-next for over a week with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ12Wwg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymbWgCeKUCeGFlUanDHY1nHq72FSMiHpcUAoIvzBTx1
yUEhvtuYYZ/NBzfKI+8h
=WeQD
-----END PGP SIGNATURE-----
Merge tag 'usb-6.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are some small USB driver fixes for some reported issues.
Included in here are:
- typec driver bugfixes
- u_serial gadget driver bugfix for much reported and discussed issue
- dwc2 bugfixes
- midi gadget driver bugfix
- ehci-hcd driver bugfix
- other small bugfixes
All of these have been in linux-next for over a week with no reported
issues"
* tag 'usb-6.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: ucsi: Fix connector status writing past buffer size
usb: typec: ucsi: Fix completion notifications
usb: dwc2: Fix HCD port connection race
usb: dwc2: hcd: Fix GetPortStatus & SetPortFeature
usb: dwc2: Fix HCD resume
usb: gadget: u_serial: Fix the issue that gs_start_io crashed due to accessing null pointer
usb: misc: onboard_usb_dev: skip suspend/resume sequence for USB5744 SMBus support
usb: dwc3: xilinx: make sure pipe clock is deselected in usb2 only mode
usb: core: hcd: only check primary hcd skip_phy_initialization
usb: gadget: midi2: Fix interpretation of is_midi1 bits
usb: dwc3: imx8mp: fix software node kernel dump
usb: typec: anx7411: fix OF node reference leaks in anx7411_typec_switch_probe()
usb: typec: anx7411: fix fwnode_handle reference leak
usb: host: max3421-hcd: Correctly abort a USB request.
dt-bindings: phy: imx8mq-usb: correct reference to usb-switch.yaml
usb: ehci-hcd: fix call balance of clocks handling routines
Improve naming consistency with the .sdev_prep() and .sdev_destroy()
methods by renaming .device_configure() into .sdev_configure().
Cc: Christoph Hellwig <hch@lst.de>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-3-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename .slave_alloc() into .sdev_init() and .slave_destroy() into
.sdev_destroy(). The new names make it clear that these are actions on
SCSI devices. Make this change in the SCSI core, SCSI drivers and also
in the ATA drivers. No functionality has been changed.
This patch has been created as follows:
* Change the text "slave_alloc" into "sdev_init" in all source files
except those in drivers/net/ and Documentation/.
* Change the text "slave_destroy" into "sdev_destroy" in all source
files except those in drivers/net/ and Documentation/.
* Rename lpfc_no_slave() into lpfc_no_sdev().
* Manually adjust whitespace where necessary to restore vertical
alignment (dc395x driver and include/linux/libata.h).
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The meaning of this value is already used in several places,
but with constant values and comments to explain it separately.
It's better to have a central place to do this then use the macro
in those places for better readability.
Signed-off-by: Dingyan Li <18500469033@163.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241030083858.46907-1-18500469033@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OPM PPM LPM
| 1.send cmd | |
|-------------------------->| |
| |-- |
| | | 2.set busy bit in CCI |
| |<- |
| 3.notify the OPM | |
|<--------------------------| |
| | 4.send cmd to be executed |
| |-------------------------->|
| | |
| | 5.cmd completed |
| |<--------------------------|
| | |
| |-- |
| | | 6.set cmd completed |
| |<- bit in CCI |
| | |
| 7.notify the OPM | |
|<--------------------------| |
| | |
| 8.handle notification | |
| from point 3, read CCI | |
|<--------------------------| |
| | |
When the PPM receives command from the OPM (p.1) it sets the busy bit
in the CCI (p.2), sends notification to the OPM (p.3) and forwards the
command to be executed by the LPM (p.4). When the PPM receives command
completion from the LPM (p.5) it sets command completion bit in the CCI
(p.6) and sends notification to the OPM (p.7). If command execution by
the LPM is fast enough then when the OPM starts handling the notification
from p.3 in p.8 and reads the CCI value it will see command completion bit
set and will call complete(). Then complete() might be called again when
the OPM handles notification from p.7.
This fix replaces test_bit() with test_and_clear_bit()
in ucsi_notify_common() in order to call complete() only
once per request.
This fix also reinitializes completion variable in
ucsi_sync_control_common() before a command is sent.
Fixes: 584e8df589 ("usb: typec: ucsi: extract common code for command handling")
Cc: stable@vger.kernel.org
Signed-off-by: Łukasz Bartosik <ukaszb@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241203102318.3386345-1-ukaszb@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Raspberry Pis without onboard USB hub frequent device reconnects
can trigger a interrupt storm after DWC2 entered host clock gating.
This is caused by a race between _dwc2_hcd_suspend() and the port
interrupt, which sets port_connect_status. The issue occurs if
port_connect_status is still 1, but there is no connection anymore:
usb 1-1: USB disconnect, device number 25
dwc2 3f980000.usb: _dwc2_hcd_suspend: port_connect_status: 1
dwc2 3f980000.usb: Entering host clock gating.
Disabling IRQ #66
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.12.0-gc1bb81b13202-dirty #322
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1d01f20 to 0xc1d01f68)
1f20: 0004ef3c 00000001 00000000 00000000 c1d09780 c1f6bb5c c1d04e54 c1c60ca8
1f40: c1d04e94 00000000 00000000 c1d092a8 c1f6af20 c1d01f70 c1211b98 c1212f40
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<e3a25c00>] dwc2_handle_common_intr
[<58bf98a3>] usb_hcd_irq
Disabling IRQ #66
So avoid this by reading the connection status directly.
Fixes: 113f86d0c3 ("usb: dwc2: Update partial power down entering by system suspend")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-4-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Rasperry Pis without onboard USB hub the power cycle during
power connect init only disable the port but never enabled it again:
usb usb1-port1: attempt power cycle
The port relevant part in dwc2_hcd_hub_control() is skipped in case
port_connect_status = 0 under the assumption the core is or will be soon
in device mode. But this assumption is wrong, because after ClearPortFeature
USB_PORT_FEAT_POWER the port_connect_status will also be 0 and
SetPortFeature (incl. USB_PORT_FEAT_POWER) will be a no-op.
Fix the behavior of dwc2_hcd_hub_control() by replacing the
port_connect_status check with dwc2_is_device_mode().
Link: https://github.com/raspberrypi/linux/issues/6247
Fixes: 7359d482eb ("staging: HCD files for the DWC2 driver")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-3-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Raspberry Pi can suffer on interrupt storms on HCD resume. The dwc2
driver sometimes misses to enable HCD_FLAG_HW_ACCESSIBLE before re-enabling
the interrupts. This causes a situation where both handler ignore a incoming
port interrupt and force the upper layers to disable the dwc2 interrupt
line. This leaves the USB interface in a unusable state:
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 6.10.0-rc3
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1b01f20 to 0xc1b01f68)
1f20: 0005c0d4 00000001 00000000 00000000 c1b09780 c1d6b32c c1b04e54 c1a5eae8
1f40: c1b04e90 00000000 00000000 00000000 c1d6a8a0 c1b01f70 c11d2da8 c11d4160
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<f539e0f4>] dwc2_handle_common_intr
[<75cd278b>] usb_hcd_irq
Disabling IRQ #66
So enable the HCD_FLAG_HW_ACCESSIBLE flag in case there is a port
connection.
Fixes: c74c26f6e3 ("usb: dwc2: Fix partial power down exiting by system resume")
Closes: https://lore.kernel.org/linux-usb/3fd0c2fb-4752-45b3-94eb-42352703e1fd@gmx.net/T/
Link: https://lore.kernel.org/all/5e8cbce0-3260-2971-484f-fc73a3b2bd28@synopsys.com/
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-2-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Considering that in some extreme cases,
when u_serial driver is accessed by multiple threads,
Thread A is executing the open operation and calling the gs_open,
Thread B is executing the disconnect operation and calling the
gserial_disconnect function,The port->port_usb pointer will be set to NULL.
E.g.
Thread A Thread B
gs_open() gadget_unbind_driver()
gs_start_io() composite_disconnect()
gs_start_rx() gserial_disconnect()
... ...
spin_unlock(&port->port_lock)
status = usb_ep_queue() spin_lock(&port->port_lock)
spin_lock(&port->port_lock) port->port_usb = NULL
gs_free_requests(port->port_usb->in) spin_unlock(&port->port_lock)
Crash
This causes thread A to access a null pointer (port->port_usb is null)
when calling the gs_free_requests function, causing a crash.
If port_usb is NULL, the release request will be skipped as it
will be done by gserial_disconnect.
So add a null pointer check to gs_start_io before attempting
to access the value of the pointer port->port_usb.
Call trace:
gs_start_io+0x164/0x25c
gs_open+0x108/0x13c
tty_open+0x314/0x638
chrdev_open+0x1b8/0x258
do_dentry_open+0x2c4/0x700
vfs_open+0x2c/0x3c
path_openat+0xa64/0xc60
do_filp_open+0xb8/0x164
do_sys_openat2+0x84/0xf0
__arm64_sys_openat+0x70/0x9c
invoke_syscall+0x58/0x114
el0_svc_common+0x80/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x38/0x68
Fixes: c1dca562be ("usb gadget: split out serial core")
Cc: stable@vger.kernel.org
Suggested-by: Prashanth K <quic_prashk@quicinc.com>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Acked-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/TYUPR06MB62178DC3473F9E1A537DCD02D2362@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB5744 SMBus initialization is done once in probe() and doing it in resume
is not supported so avoid going into suspend and reset the HUB.
There is a sysfs property 'always_powered_in_suspend' to implement this
feature but since default state should be set to a working configuration
so override this property value.
It fixes the suspend/resume testcase on Kria KR260 Robotics Starter Kit.
Fixes: 6782311d04 ("usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support")
Cc: stable@vger.kernel.org
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1733165302-1694891-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the USB3 PHY is not defined in the Linux device tree, there could
still be a case where there is a USB3 PHY active on the board and enabled
by the first stage bootloader. If serdes clock is being used then the USB
will fail to enumerate devices in 2.0 only mode.
To solve this, make sure that the PIPE clock is deselected whenever the
USB3 PHY is not defined and guarantees that the USB2 only mode will work
in all cases.
Fixes: 9678f3361a ("usb: dwc3: xilinx: Skip resets and USB3 register settings for USB2.0 mode")
Cc: stable@vger.kernel.org
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/1733163111-1414816-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit 53a2d95df8 ("usb: core: add phy notify connect and
disconnect"), phy initialization will be skipped even when shared hcd
doesn't set skip_phy_initialization flag. However, the situation is
changed after the commit. The hcd.c will initialize phy when add shared
hcd. This behavior is unexpected for some platforms which will handle phy
initialization by themselves. To avoid the issue, this will only check
skip_phy_initialization flag of primary hcd since shared hcd normally
follow primary hcd setting.
Fixes: 53a2d95df8 ("usb: core: add phy notify connect and disconnect")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20241105090120.2438366-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UMP Function Block info m1.0 field (represented by is_midi1 sysfs
entry) is an enumeration from 0 to 2, while the midi2 gadget driver
incorrectly copies it to the corresponding snd_ump_block_info.flags
bits as-is. This made the wrong bit flags set when m1.0 = 2.
This patch corrects the wrong interpretation of is_midi1 bits.
Fixes: 29ee7a4ddd ("usb: gadget: midi2: Add configfs support")
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20241127070213.8232-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unbind and bind the device again, kernel will dump below warning:
[ 173.972130] sysfs: cannot create duplicate filename '/devices/platform/soc/4c010010.usb/software_node'
[ 173.981564] CPU: 2 UID: 0 PID: 536 Comm: sh Not tainted 6.12.0-rc6-06344-g2aed7c4a5c56 #144
[ 173.989923] Hardware name: NXP i.MX95 15X15 board (DT)
[ 173.995062] Call trace:
[ 173.997509] dump_backtrace+0x90/0xe8
[ 174.001196] show_stack+0x18/0x24
[ 174.004524] dump_stack_lvl+0x74/0x8c
[ 174.008198] dump_stack+0x18/0x24
[ 174.011526] sysfs_warn_dup+0x64/0x80
[ 174.015201] sysfs_do_create_link_sd+0xf0/0xf8
[ 174.019656] sysfs_create_link+0x20/0x40
[ 174.023590] software_node_notify+0x90/0x100
[ 174.027872] device_create_managed_software_node+0xec/0x108
...
The '4c010010.usb' device is a platform device created during the initcall
and is never removed, which causes its associated software node to persist
indefinitely.
The existing device_create_managed_software_node() does not provide a
corresponding removal function.
Replace device_create_managed_software_node() with the
device_add_software_node() and device_remove_software_node() pair to ensure
proper addition and removal of software nodes, addressing this issue.
Fixes: a9400f1979 ("usb: dwc3: imx8mp: add 2 software managed quirk properties for host mode")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241126032841.2458338-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The refcounts of the OF nodes obtained by of_get_child_by_name() calls
in anx7411_typec_switch_probe() are not decremented. Replace them with
device_get_named_child_node() calls and store the return values to the
newly created fwnode_handle fields in anx7411_data, and call
fwnode_handle_put() on them in the error path and in the unregister
functions.
Fixes: e45d7337dc ("usb: typec: anx7411: Use of_get_child_by_name() instead of of_find_node_by_name()")
Cc: stable@vger.kernel.org
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241126014909.3687917-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An fwnode_handle and usb_role_switch are obtained with an incremented
refcount in anx7411_typec_port_probe(), however the refcounts are not
decremented in the error path. The fwnode_handle is also not decremented
in the .remove() function. Therefore, call fwnode_handle_put() and
usb_role_switch_put() accordingly.
Fixes: fe6d8a9c8e ("usb: typec: anx7411: Add Analogix PD ANX7411 support")
Cc: stable@vger.kernel.org
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241121023429.962848-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the current USB request was aborted, the spi thread would not respond
to any further requests. This is because the "curr_urb" pointer would
not become NULL, so no further requests would be taken off the queue.
The solution here is to set the "urb_done" flag, as this will cause the
correct handling of the URB. Also clear interrupts that should only be
expected if an URB is in progress.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable <stable@kernel.org>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20241124221430.1106080-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the clocks priv->iclk and priv->fclk were not enabled in ehci_hcd_sh_probe,
they should not be disabled in any path.
Conversely, if they was enabled in ehci_hcd_sh_probe, they must be disabled
in all error paths to ensure proper cleanup.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: 63c8455222 ("usb: ehci-hcd: Add support for SuperH EHCI.")
Cc: stable@vger.kernel.org # ff30bd6a66: sh: clk: Fix clk_enable() to return 0 on NULL clk
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241121114700.2100520-1-mordan@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a device is inserted into the USB port and an S4 wakeup is initiated,
after the USB-hub initialization is completed, it will automatically enter
suspend mode. Upon detecting a device on the USB port, it will proceed with
resume and set the hcd to the HCD_FLAG_WAKEUP_PENDING state. During the S4
wakeup process, peripherals are put into suspend mode, followed by task
recovery. However, upon detecting that the hcd is in the
HCD_FLAG_WAKEUP_PENDING state, it will return an EBUSY status, causing the
S4 suspend to fail and subsequent task recovery to not proceed.
-
[ 27.594598][ 1] PM: pci_pm_freeze(): hcd_pci_suspend+0x0/0x28 returns -16
[ 27.594601][ 1] PM: dpm_run_callback(): pci_pm_freeze+0x0/0x100 returns -16
[ 27.603420][ 1] ehci-pci 0000:00:04.1: pci_pm_freeze+0x0/0x100 returned 0 after 3 usecs
[ 27.612233][ 1] ehci-pci 0000:00:05.1: pci_pm_freeze+0x0/0x100 returned -16 after 17223 usecs
[ 27.810067][ 1] PM: Device 0000:00:05.1 failed to quiesce async: error -16
[ 27.816988][ 1] PM: quiesce of devices aborted after 1833.282 msecs
[ 27.823302][ 1] PM: start quiesce of devices aborted after 1839.975 msecs
......
[ 31.303172][ 1] PM: recover of devices complete after 3473.039 msecs
[ 31.309818][ 1] PM: Failed to load hibernation image, recovering.
[ 31.348188][ 1] PM: Basic memory bitmaps freed
[ 31.352686][ 1] OOM killer enabled.
[ 31.356232][ 1] Restarting tasks ... done.
[ 31.360609][ 1] PM: resume from hibernation failed (0)
[ 31.365800][ 1] PM: Hibernation image not present or could not be loaded.
The "do_wakeup" is determined based on whether the controller's
power/wakeup attribute is set. The current issue necessitates considering
the type of suspend that is occurring. If the suspend type is either
PM_EVENT_FREEZE or PM_EVENT_QUIESCE, then "do_wakeup" should be set to
false.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410151722.rfjtknRz-lkp@intel.com/
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Duan Chenghao <duanchenghao@kylinos.cn>
Link: https://lore.kernel.org/r/20241024024038.26157-1-duanchenghao@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coverity from Synopsys complains "Illegal address computation (OVERRUN)"
on status_reg.
After below code executed,
port_index = wIndex & 0xff;
port_index -= (port_index > 0);
the static analysis tool see the value of port_index is now between 0 and
254 (inclusive).
However, ehci_def.h define port_status as below:
#define HCS_N_PORTS_MAX 15
u32 port_status[HCS_N_PORTS_MAX];
So the tool think illegal array pointer may be obtained.
status_reg = &ehci->regs->port_status[port_index];
This will follow "846cbf98cbef USB: EHCI: Improve port index sanitizing" to
improve port index sanitizing.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20241202083453.704533-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STAR 9001346572 addresses a USB 2.0 endpoint blocking issue in host mode
for controller versions DWC_usb31 1.70a and 1.80a. This issue affects
devices on both high-speed and full-speed bus instances. When all
endpoint caches are filled and a single active endpoint receives
continuous NAK responses, data transfers to other endpoints may get
blocked.
To resolve this, for controller versions DWC_usb31 1.70a and 1.80a, the
GUCTL3 bit[16] (USB2.0 Internal Retry Disable) is set to 1. This bit
disables the USB2.0 internal retry feature and ensures proper eviction
handling in the host controller endpoind cache. The GUCTL3[16] register
function is available only from DWC_usb31 version 1.70a.
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241129173422.20063-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two Kconfig "comment" calls render in /proc/config.gz as split
sections:
#
# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#
#
# also be needed; see USB_STORAGE Help for more info
#
"make menuconfig" renders the comments as:
*** NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may ***
*** also be needed; see USB_STORAGE Help for more info ***
Kconfig doesn't support splitting a comment cleanly over two lines, so
just collapse it into a single oversize comment.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241127232830.26923-2-ddiss@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sg (scatter-gather list pointer) member of the dwc3_request struct
is no longer used and should be removed. This patch eliminates the unused
member, cleaning up the struct.
This change improves code clarity and avoids maintaining unnecessary
members in the structure.
Reviewed-by: Ricardo B. Marliere <rbm@suse.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/all/20241118194006.77c7b126@canb.auug.org.au/
Signed-off-by: Luis Felipe Hernandez <luis.hernandez093@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241120154604.51815-1-luis.hernandez093@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The header clearly states that it does not want to be included directly,
only via 'device.h'. 'platform_device.h' works equally well. Remove the
direct inclusion.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241118072917.3853-15-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cdd30ebb1b ("module: Convert symbol namespace to string
literal") only converted MODULE_IMPORT_NS() and EXPORT_SYMBOL_NS(),
leaving DEFAULT_SYMBOL_NAMESPACE as a macro expansion.
This commit converts DEFAULT_SYMBOL_NAMESPACE in the same way to avoid
annoyance for the default namespace as well.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add generic support for built-in boot DTB files
- Enable TAB cycling for dialog buttons in nconfig
- Fix issues in streamline_config.pl
- Refactor Kconfig
- Add support for Clang's AutoFDO (Automatic Feedback-Directed
Optimization)
- Add support for Clang's Propeller, a profile-guided optimization.
- Change the working directory to the external module directory for M=
builds
- Support building external modules in a separate output directory
- Enable objtool for *.mod.o and additional kernel objects
- Use lz4 instead of deprecated lz4c
- Work around a performance issue with "git describe"
- Refactor modpost
-----BEGIN PGP SIGNATURE-----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=GDKD
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add generic support for built-in boot DTB files
- Enable TAB cycling for dialog buttons in nconfig
- Fix issues in streamline_config.pl
- Refactor Kconfig
- Add support for Clang's AutoFDO (Automatic Feedback-Directed
Optimization)
- Add support for Clang's Propeller, a profile-guided optimization.
- Change the working directory to the external module directory for M=
builds
- Support building external modules in a separate output directory
- Enable objtool for *.mod.o and additional kernel objects
- Use lz4 instead of deprecated lz4c
- Work around a performance issue with "git describe"
- Refactor modpost
* tag 'kbuild-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (85 commits)
kbuild: rename .tmp_vmlinux.kallsyms0.syms to .tmp_vmlinux0.syms
gitignore: Don't ignore 'tags' directory
kbuild: add dependency from vmlinux to resolve_btfids
modpost: replace tdb_hash() with hash_str()
kbuild: deb-pkg: add python3:native to build dependency
genksyms: reduce indentation in export_symbol()
modpost: improve error messages in device_id_check()
modpost: rename alias symbol for MODULE_DEVICE_TABLE()
modpost: rename variables in handle_moddevtable()
modpost: move strstarts() to modpost.h
modpost: convert do_usb_table() to a generic handler
modpost: convert do_of_table() to a generic handler
modpost: convert do_pnp_device_entry() to a generic handler
modpost: convert do_pnp_card_entries() to a generic handler
modpost: call module_alias_printf() from all do_*_entry() functions
modpost: pass (struct module *) to do_*_entry() functions
modpost: remove DEF_FIELD_ADDR_VAR() macro
modpost: deduplicate MODULE_ALIAS() for all drivers
modpost: introduce module_alias_printf() helper
modpost: remove unnecessary check in do_acpi_entry()
...
Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the 2 simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups that
can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog
As mentioned above, there is 2 merge conflicts with your tree, one is
where the file is removed (easy enough to resolve), the second is a
build time error, that has been found in linux-next and the fix can be
seen here:
https://lore.kernel.org/r/20241107212645.41252436@canb.auug.org.au
Other than that, the changes here have been in linux-next with no other
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ0lEog8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym+0ACgw6wN+LkLVIHWhxTq5DYHQ0QCxY8AoJrRIcKe
78h0+OU3OXhOy8JGz62W
=oI5S
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the two simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups
that can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog"
* tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Fix a potential abuse of seq_printf() format string in drivers
cpu: Remove spurious NULL in attribute_group definition
s390/con3215: Remove spurious NULL in attribute_group definition
perf: arm-ni: Remove spurious NULL in attribute_group definition
driver core: Constify bin_attribute definitions
sysfs: attribute_group: allow registration of const bin_attribute
firmware_loader: Fix possible resource leak in fw_log_firmware_info()
drivers: core: fw_devlink: Fix excess parameter description in docstring
driver core: class: Correct WARN() message in APIs class_(for_each|find)_device()
cacheinfo: Use of_property_present() for non-boolean properties
cdx: Fix cdx_mmap_resource() after constifying attr in ->mmap()
drivers: core: fw_devlink: Make the error message a bit more useful
phy: tegra: xusb: Set fwnode for xusb port devices
drm: display: Set fwnode for aux bus devices
driver core: fw_devlink: Stop trying to optimize cycle detection logic
driver core: Constify attribute arguments of binary attributes
sysfs: bin_attribute: add const read/write callback variants
sysfs: implement all BIN_ATTR_* macros in terms of __BIN_ATTR()
sysfs: treewide: constify attribute callback of bin_attribute::llseek()
sysfs: treewide: constify attribute callback of bin_attribute::mmap()
...
Here is the big set of USB and Thunderbolt changes for 6.13-rc1.
Overall, a pretty slow development cycle, the majority of the work going
into the debugfs interface for the thunderbolt (i.e. USB4) code, to help
with debugging the myrad ways that hardware vendors get their interfaces
messed up. Other than that, here's the highlights:
- thunderbolt changes and additions to debugfs interfaces
- lots of device tree updates for new and old hardware
- UVC configfs gadget updates and new apis for features
- xhci driver updates and fixes
- dwc3 driver updates and fixes
- typec driver updates and fixes
- lots of other small updates and fixes, full details in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ0lBqA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynTXQCfSs0ldBqZoINU/22q8BUg7ybb+pcAoL5EbbEm
b2igfp6YIEWAtUkactmO
=gwwq
-----END PGP SIGNATURE-----
Merge tag 'usb-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.13-rc1.
Overall, a pretty slow development cycle, the majority of the work
going into the debugfs interface for the thunderbolt (i.e. USB4) code,
to help with debugging the myrad ways that hardware vendors get their
interfaces messed up. Other than that, here's the highlights:
- thunderbolt changes and additions to debugfs interfaces
- lots of device tree updates for new and old hardware
- UVC configfs gadget updates and new apis for features
- xhci driver updates and fixes
- dwc3 driver updates and fixes
- typec driver updates and fixes
- lots of other small updates and fixes, full details in the shortlog
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (148 commits)
usb: typec: tcpm: Add support for sink-bc12-completion-time-ms DT property
dt-bindings: usb: maxim,max33359: add usage of sink bc12 time property
dt-bindings: connector: Add time property for Sink BC12 detection completion
usb: dwc3: gadget: Remove dwc3_request->needs_extra_trb
usb: dwc3: gadget: Cleanup SG handling
usb: dwc3: gadget: Fix looping of queued SG entries
usb: dwc3: gadget: Fix checking for number of TRBs left
usb: dwc3: ep0: Don't clear ep0 DWC3_EP_TRANSFER_STARTED
Revert "usb: gadget: composite: fix OS descriptors w_value logic"
usb: ehci-spear: fix call balance of sehci clk handling routines
USB: make to_usb_device_driver() use container_of_const()
USB: make to_usb_driver() use container_of_const()
USB: properly lock dynamic id list when showing an id
USB: make single lock for all usb dynamic id lists
drivers/usb/storage: refactor min with min_t
drivers/usb/serial: refactor min with min_t
drivers/usb/musb: refactor min/max with min_t/max_t
drivers/usb/mon: refactor min with min_t
drivers/usb/misc: refactor min with min_t
drivers/usb/host: refactor min/max with min_t/max_t
...
tps65010, have undergone minor code improvements to enhance consistency and
fix race conditions.
- The syscon driver now utilizes the regmap max_register_is_0 capability
for consistent register map configuration across syscons of all sizes.
- New device support has been added for QCS8300, qcs615, SA8255p, and
samsung,s2dos05, expanding the range of compatible hardware.
- The cros_ec driver now supports loading cros_ec_ucsi on supported ECs
and avoids loading the charger with UCSI, streamlining functionality.
- The bd96801 driver now utilizes the more modern maple tree register
cache, improving performance.
- The da9052-spi driver has undergone a fix to change the read-mask to
write-mask, preventing potential issues.
- Unused declarations in max77693 have been removed, and support for
samsung,s2dos05 has been added, enhancing code clarity and device compatibility.
- Error handling in cs42l43 has been fixed to avoid unbalanced regulator
put and ensure proper synchronization during driver removal.
- The wcd934x driver now uses MODULE_DEVICE_TABLE() instead of
MODULE_ALIAS(), improving code consistency.
- Documentation for qcom,tcsr, syscon, and atmel-smc has been updated
and reorganized for better clarity and maintainability.
- The intel_soc_pmic_bxtwc driver has undergone significant improvements,
including the use of IRQ domains for various devices, fixing IRQ domain names
duplication, and code refactoring for better consistency and maintainability.
- The ipaq-micro driver has received a fix for a missing break statement in
the default case, enhancing code robustness.
- Support for the AXP323 PMIC has been added to the axp20x driver, along
with ensuring a clear relationship between IDs and model names, and allowing
multiple regulators, broadening hardware compatibility.
- The cs42l43 driver now disables IRQs during suspend for improved power
management.
- The adp5585 driver has reduced its dependencies by dropping the obsolete
dependency on COMPILE_TEST.
- Initial support for the MT6328 PMIC has been added to the mt6397 driver,
expanding the range of supported hardware.
- The rtc-bd70528 driver has been simplified by dropping the IC name from
IRQ, improving code readability.
- Documentation for qcom,spmi-pmic, ti,twl, and zii,rave-sp has been
updated to enhance clarity and incorporate new features.
- The rt5033 driver has received a fix for a missing regmap_del_irq_chip()
in the error handling path.
- New device support has been added for MSM8917, and the
intel_soc_pmic_crc driver now supports non-ACPI instantiated i2c_client.
- The 88pm886 driver has added support for the RTC cell, and the tqmx86
driver has improved its GPIO IRQ setup and added I2C IRQ support,
increasing functionality.
- The sprd,sc2731 DT schema has been updated and converted to YAML format
for better readability and maintainability.
-----BEGIN PGP SIGNATURE-----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=YP3r
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
- Several drivers, including atmel-flexcom/rk8xx-core, palmas, and
tps65010, have undergone minor code improvements to enhance
consistency and fix race conditions.
- The syscon driver now utilizes the regmap max_register_is_0
capability for consistent register map configuration across syscons
of all sizes.
- New device support has been added for QCS8300, qcs615, SA8255p, and
samsung,s2dos05, expanding the range of compatible hardware.
- The cros_ec driver now supports loading cros_ec_ucsi on supported ECs
and avoids loading the charger with UCSI, streamlining functionality.
- The bd96801 driver now utilizes the more modern maple tree register
cache, improving performance.
- The da9052-spi driver has undergone a fix to change the read-mask to
write-mask, preventing potential issues.
- Unused declarations in max77693 have been removed, and support for
samsung,s2dos05 has been added, enhancing code clarity and device
compatibility.
- Error handling in cs42l43 has been fixed to avoid unbalanced
regulator put and ensure proper synchronization during driver
removal.
- The wcd934x driver now uses MODULE_DEVICE_TABLE() instead of
MODULE_ALIAS(), improving code consistency.
- Documentation for qcom,tcsr, syscon, and atmel-smc has been updated
and reorganized for better clarity and maintainability.
- The intel_soc_pmic_bxtwc driver has undergone significant
improvements, including the use of IRQ domains for various devices,
fixing IRQ domain names duplication, and code refactoring for better
consistency and maintainability.
- The ipaq-micro driver has received a fix for a missing break
statement in the default case, enhancing code robustness.
- Support for the AXP323 PMIC has been added to the axp20x driver,
along with ensuring a clear relationship between IDs and model names,
and allowing multiple regulators, broadening hardware compatibility.
- The cs42l43 driver now disables IRQs during suspend for improved
power management.
- The adp5585 driver has reduced its dependencies by dropping the
obsolete dependency on COMPILE_TEST.
- Initial support for the MT6328 PMIC has been added to the mt6397
driver, expanding the range of supported hardware.
- The rtc-bd70528 driver has been simplified by dropping the IC name
from IRQ, improving code readability.
- Documentation for qcom,spmi-pmic, ti,twl, and zii,rave-sp has been
updated to enhance clarity and incorporate new features.
- The rt5033 driver has received a fix for a missing
regmap_del_irq_chip() in the error handling path.
- New device support has been added for MSM8917, and the
intel_soc_pmic_crc driver now supports non-ACPI instantiated
i2c_client.
- The 88pm886 driver has added support for the RTC cell, and the tqmx86
driver has improved its GPIO IRQ setup and added I2C IRQ support,
increasing functionality.
- The sprd,sc2731 DT schema has been updated and converted to YAML
format for better readability and maintainability.
* tag 'mfd-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (62 commits)
dt-bindings: mfd: bd71828: Use charger resistor in mOhm instead of MOhm
dt-bindings: mfd: sprd,sc2731: Convert to YAML
mfd: tqmx86: Add I2C IRQ support
mfd: tqmx86: Make IRQ setup errors non-fatal
mfd: tqmx86: Refactor GPIO IRQ setup
mfd: tqmx86: Improve gpio_irq module parameter description
mfd: tqmx86: Add board definitions for TQMx120UC, TQMx130UC and TQMxE41S
mfd: 88pm886: Add the RTC cell
dt-bindings: mfd: Add Realtek RTL9300 switch peripherals
mfd: intel_soc_pmic_crc: Add support for non ACPI instantiated i2c_client
mfd: intel_soc_pmic_*: Consistently use filename as driver name
dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8917
mfd: rt5033: Fix missing regmap_del_irq_chip()
mfd: cgbc-core: Fix error handling paths in cgbc_init_device()
dt-bindings: mfd: aspeed: Support for AST2700
mfd: Switch back to struct platform_driver::remove()
dt-bindings: mfd: qcom,spmi-pmic: Document PMICs added in SM8750
mfd: rtc: bd7xxxx Drop IC name from IRQ
mfd: mt6397: Add initial support for MT6328
mfd: adp5585: Drop obsolete dependency on COMPILE_TEST
...
GPIOLIB core:
- use the new mem_is_zero() instead of memchr_inv(s, 0, n)
- don't store debounce period twice needlessly
- clean-up debugfs handling
- remove leftover comments referring to no longer used spinlocks
- unduplicate some operations like SRCU locks and initializing GPIO descriptors
- constify the sysfs class struct
- use lock guards in GPIO sysfs code
- update GPIO uAPI internal flags all at once atomically for consistency with
other places
- modify the behavior of the sysfs interface by no longer exporting lines that
are named inside the driver code or board files with the sysfs links bearing
the line names as this has for many years been largely unused due to the
prevalence of DT, ACPI and firmware nodes over board files and made the API
inconsistent
- for GPIO interrupt providers: free irqs that are still requested by users
when removing the chip
GPIO uAPI:
- notify user-space about changes to GPIO lines' state (requested, released,
reconfigured) triggered from the kernel as well (until now we'd only do
this for changes triggered from user-space)
- to that end: modify the internal workings of the notification mechanism by
switching to an atomic notifier which allows us to send events from atomic
context
- also to that end store the debounce period in the GPIO descriptor struct
and not in the character device context struct
- while at it, also cover the corner-case of users introducing changes over
sysfs while others watch them via the character device
- don't report GPIO lines requested as interrupts as "used" to user-space as it
can still request them as GPIOs
New drivers:
- add a driver for the GPIO functionality of the MFD Congatec Board Controller
- add a driver for the PolarFire GPIO controller
- add a driver supporting the GPIOs on FTDI FT2232H
Driver improvements:
- use generic device property accessors instead of OF-specific ones across
many GPIO drivers (mpc8xxx, vf610, eic-sprd, davinci, ts4900, xilinx, mvebu)
- use devres helpers to simplify error paths and either shrink or entirely
remove the driver's remove() callback (grgpio, amdpt, menz127, max730x,
ftgpio010, 74x164, ljca)
- use helper variables to store the address of pdev->dev and avoid some
line-breaks
- use device_for_each_child_node_scoped() to avoid having to put the fwnode
on breaks or errors (gpio-sim, gpio-dwapb, gpiolib-acpi)
- use a scoped bitmap to simplify the code and drop goto labels in
gpio-aggregator
- drop unneeded Kconfig dependencies on OF_GPIO (grgpio, mveby, xilinx)
- add support for new models to gpio-aspeed, gpio-rockchip and gpio-dwapb
- clean-up ACPI handling and some other bits in gpio-xgene-sb
- replace deprecated PCI functions in pcie-idio-24 and pci-idio-16
- allow to build davinci and mvebu drivers with COMPILE_TEST=y
- remove dead code in gpio-mb86s7x
- switch back to using platform_driver::remove() (after the conversion to
remove_new()) across the GPIO drivers
- remove remaining uses of GPIOF_ACTIVE_LOW across the tree and drop this
deprecated symbol
- convert the gpio-altera driver to no longer pull in the deprecated
legacy-of-mm-gpiochip.h header
- use of_property_present() instead of of_property_read_bool() in gpiolib-of
and gpio-rockchip
- allow to build the tegra186 driver on Tegra234 platforms in Kconfig
Late fixes:
- add a missing return value check after devm_kasprintf() to gpio-grgpio
DT bindings:
- document the ngpios property of gpio-mmio
- add support for a new aspeed model
- fix the example for st,nomadik-gpio
Other:
- kernel doc and comments tweaks
- fix typos in TODO
- reorder headers alphabetically in some drivers
- fix incorrect format specifiers in gpio tools
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEFp3rbAvDxGAT0sefEacuoBRx13IFAmc7INQACgkQEacuoBRx
13Kotg/8DDkhZ01Qc2uR817DjCdbalS0TDr4FYn/XusyeBEgNgQDm/TcfmIMiU4M
Dazb7pOXfEc4VJqPTSpvqsTwTyMLN1pi58ZXZZA760rf8O8O+8c/cogVk36QK+IB
3LX/w7JFFME6cC3kZ+mV3a6Cdxb4UIQdv1rWtLX8MjCiJ5+ax33VS0pe67n8sOft
A6LeYwFr1ngk9NDg+OrFzExMTCGqk4aUYWiLd8ki3bw5ZMYzLwuenWLONQo3HOP5
QuWQV+wF913mjB53omiZ8heJ7hN3ez071W4rXXPGXn5sAGipqJKWk6Nvx1wRZapD
d+6XozBLGNEIcPvWJAWDfxnHmEjVpFyhavc9Id569DcQ0WVLm+CFPkNmp4mgOoOB
k8f6R2CA2lheIKTRUk/Lt+Cu2+Za/07bM/WsxL6x/oCXZwL6NA5P+8VoNcBCDKrF
PVUz7Jad6FVHkxySqwX4clHLW173pqyG47RJ7KxVv7g6g+YNW0WCM7crS+czRWIq
KUT9sumw1dEFlYZ9IGZTuP/Pvur8f17powkS8VuYJ02N1yq3OhQZb52NX8stsmkW
P6CsdZe9KRoGQUJp9nYVE5j09oz1gqqdbLdn4Byqg6G50w2U1mLNaWE1rtWLtcTx
h7npUNOaX44JafnClFJvv1R9ovkuzgTaymEL4qo3QB6COHdvjlA=
=ON7q
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"Three new drivers, support for some new models in existing ones and
lots of various tweaks and improvements across the board (switching to
using recommended APIs, code shrink and simplification, etc.).
Also a new feature in the character device uAPI where we now notify
the user-space about changes triggered by in-kernel users as well, not
only when they were done by other user-space agents.
Summary:
GPIOLIB core:
- use the new mem_is_zero() instead of memchr_inv(s, 0, n)
- don't store debounce period twice needlessly
- clean-up debugfs handling
- remove leftover comments referring to no longer used spinlocks
- unduplicate some operations like SRCU locks and initializing GPIO
descriptors
- constify the sysfs class struct
- use lock guards in GPIO sysfs code
- update GPIO uAPI internal flags all at once atomically for
consistency with other places
- modify the behavior of the sysfs interface by no longer exporting
lines that are named inside the driver code or board files with the
sysfs links bearing the line names as this has for many years been
largely unused due to the prevalence of DT, ACPI and firmware nodes
over board files and made the API inconsistent
- for GPIO interrupt providers: free irqs that are still requested by
users when removing the chip
GPIO uAPI:
- notify user-space about changes to GPIO lines' state (requested,
released, reconfigured) triggered from the kernel as well (until
now we'd only do this for changes triggered from user-space)
- to that end: modify the internal workings of the notification
mechanism by switching to an atomic notifier which allows us to
send events from atomic context
- also to that end store the debounce period in the GPIO descriptor
struct and not in the character device context struct
- while at it, also cover the corner-case of users introducing
changes over sysfs while others watch them via the character device
- don't report GPIO lines requested as interrupts as "used" to
user-space as it can still request them as GPIOs
New drivers:
- GPIO part of the MFD Congatec Board Controller
- PolarFire GPIO controller
- GPIOs on FTDI FT2232H
Driver improvements:
- use generic device property accessors instead of OF-specific ones
across many GPIO drivers (mpc8xxx, vf610, eic-sprd, davinci,
ts4900, xilinx, mvebu)
- use devres helpers to simplify error paths and either shrink or
entirely remove the driver's remove() callback (grgpio, amdpt,
menz127, max730x, ftgpio010, 74x164, ljca)
- use helper variables to store the address of pdev->dev and avoid
some line-breaks
- use device_for_each_child_node_scoped() to avoid having to put the
fwnode on breaks or errors (gpio-sim, gpio-dwapb, gpiolib-acpi)
- use a scoped bitmap to simplify the code and drop goto labels in
gpio-aggregator
- drop unneeded Kconfig dependencies on OF_GPIO (grgpio, mveby,
xilinx)
- add support for new models to gpio-aspeed, gpio-rockchip and
gpio-dwapb
- clean-up ACPI handling and some other bits in gpio-xgene-sb
- replace deprecated PCI functions in pcie-idio-24 and pci-idio-16
- allow to build davinci and mvebu drivers with COMPILE_TEST=y
- remove dead code in gpio-mb86s7x
- switch back to using platform_driver::remove() (after the
conversion to remove_new()) across the GPIO drivers
- remove remaining uses of GPIOF_ACTIVE_LOW across the tree and drop
this deprecated symbol
- convert the gpio-altera driver to no longer pull in the deprecated
legacy-of-mm-gpiochip.h header
- use of_property_present() instead of of_property_read_bool() in
gpiolib-of and gpio-rockchip
- allow to build the tegra186 driver on Tegra234 platforms in Kconfig
Late fixes:
- add a missing return value check after devm_kasprintf() to
gpio-grgpio
DT bindings:
- document the ngpios property of gpio-mmio
- add support for a new aspeed model
- fix the example for st,nomadik-gpio
Other:
- kernel doc and comments tweaks
- fix typos in TODO
- reorder headers alphabetically in some drivers
- fix incorrect format specifiers in gpio tools"
* tag 'gpio-updates-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (98 commits)
gpio: tegra186: Allow to enable driver on Tegra234
gpio: grgpio: Add NULL check in grgpio_probe
tools: gpio: Fix several incorrect format specifiers
gpio: mpfs: add CoreGPIO support
gpio: rockchip: support new version GPIO
gpio: rockchip: change the GPIO version judgment logic
gpio: rockchip: explan the format of the GPIO version ID
gpiolib: cdev: use !mem_is_zero() instead of memchr_inv(s, 0, n)
MAINTAINERS: add gpio driver to PolarFire entry
gpio: Get rid of GPIOF_ACTIVE_LOW
USB: gadget: pxa27x_udc: Avoid using GPIOF_ACTIVE_LOW
pcmcia: soc_common: Avoid using GPIOF_ACTIVE_LOW
leds: gpio: Avoid using GPIOF_ACTIVE_LOW
Input: gpio_keys_polled - avoid using GPIOF_ACTIVE_LOW
Input: gpio_keys - avoid using GPIOF_ACTIVE_LOW
gpio: Use of_property_present() for non-boolean properties
gpio: mpfs: add polarfire soc gpio support
gpio: altera: Drop legacy-of-mm-gpiochip.h header
gpio: pcie-idio-24: Replace deprecated PCI functions
gpio: pci-idio-16: Replace deprecated PCI functions
...
Add support for parsing DT time property "sink-bc12-completion-time-ms".
This timer is used to relax the PD state machine during Sink attach to
allow completion of Battery Charging (BC1.2) charger type detection in
TCPC before PD negotiations. BC1.2 detection is a hardware mechanism to
detect charger port type that is run by some controllers (such as
"maxim,max33359") in parallel to Type-C connection state machines.
This is to ensure that BC1.2 completes before PD is enabled as running
BC1.2 in parallel with PD negotiation results in delays violating timer
constraints in PD spec.
This is an optional timer and will not add any delay unless explicitly
set.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241103034402.2460252-4-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current logic in dwc3 driver is tracking req->num_queued_sgs and
req->sg. But they can be checked base on the num_pending_sgs and
num_trbs. They are redundant and can complicate the SG logic. Let's
remove them.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/96c7bf8f6b3e91e607d5b78ea51cb1d00c614eaf.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3_request->num_queued_sgs is decremented on completion. If a
partially completed request is handled, then the
dwc3_request->num_queued_sgs no longer reflects the total number of
num_queued_sgs (it would be cleared).
Correctly check the number of request SG entries remained to be prepare
and queued. Failure to do this may cause null pointer dereference when
accessing non-existent SG entry.
Cc: stable@vger.kernel.org
Fixes: c96e6725db ("usb: dwc3: gadget: Correct the logic for queuing sgs")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d07a7c4aa0fcf746cdca0515150dbe5c52000af7.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check whether the TRB ring is full or empty in dwc3_calc_trbs_left()
is insufficient. It assumes there are active TRBs if there's any request
in the started_list. However, that's not the case for requests with a
large SG list.
That is, if we have a single usb request that requires more TRBs than
the total TRBs in the TRB ring, the queued TRBs will be available when
all the TRBs in the ring are completed. But the request is only
partially completed and remains in the started_list. With the current
logic, the TRB ring is empty, but dwc3_calc_trbs_left() returns 0.
Fix this by additionally checking for the request->num_trbs for active
TRB count.
Cc: stable@vger.kernel.org
Fixes: 51f1954ad8 ("usb: dwc3: gadget: Fix dwc3_calc_trbs_left()")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/708dc62b56b77da1f704cc2ae9b6ddb1f2dbef1f.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver cannot issue the End Transfer command to the SETUP transfer.
Don't clear DWC3_EP_TRANSFER_STARTED flag to make sure that the driver
won't send Start Transfer command again, which can cause no-resource
error. For example this can occur if the host issues a reset to the
device.
Cc: stable@vger.kernel.org
Fixes: 76cb323f80 ("usb: dwc3: ep0: clear all EP0 flags")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d3d618185fd614bb7426352a9fc1199641d3b5f5.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ec6ce7075e.
Fix installation of WinUSB driver using OS descriptors. Without the
fix the drivers are not installed correctly and the property
'DeviceInterfaceGUID' is missing on host side.
The original change was based on the assumption that the interface
number is in the high byte of wValue but it is in the low byte,
instead. Unfortunately, the fix is based on MS documentation which is
also wrong.
The actual USB request for OS descriptors (using USB analyzer) looks
like:
Offset 0 1 2 3 4 5 6 7
0x000 C1 A1 02 00 05 00 0A 00
C1: bmRequestType (device to host, vendor, interface)
A1: nas magic number
0002: wValue (2: nas interface)
0005: wIndex (5: get extended property i.e. nas interface GUID)
008E: wLength (142)
The fix was tested on Windows 10 and Windows 11.
Cc: stable@vger.kernel.org
Fixes: ec6ce7075e ("usb: gadget: composite: fix OS descriptors w_value logic")
Signed-off-by: Michal Vrastil <michal.vrastil@hidglobal.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Peter korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20241113235433.20244-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the clock sehci->clk was not enabled in spear_ehci_hcd_drv_probe,
it should not be disabled in any path.
Conversely, if it was enabled in spear_ehci_hcd_drv_probe, it must be disabled
in all error paths to ensure proper cleanup.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: 7675d6ba43 ("USB: EHCI: make ehci-spear a separate driver")
Cc: stable@vger.kernel.org
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241114230310.432213-1-mordan@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 6.13-rc1, including:
- improved support for quirky pl2303 hxd devices
- make sure ftdi_sio TIOCGSERIAL returns consistent data
Everything has been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZzdTXQAKCRALxc3C7H1l
COSGAP0U6gSnhn9V6cSzz9WVJwfAAifKkBB6ZvPORmOX4f5nMwEAtEEQJQtdCXD6
d/9/9hEF1Xot5nhKfOTtFMbwWM+rtgI=
=gbhm
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.13-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 6.13-rc1
Here are the USB-serial updates for 6.13-rc1, including:
- improved support for quirky pl2303 hxd devices
- make sure ftdi_sio TIOCGSERIAL returns consistent data
Everything has been in linux-next with no reported issues.
* tag 'usb-serial-6.13-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: Fix atomicity violation in get_serial_info()
USB: serial: pl2303: account for deficits of clones
Turns out that we have some const pointers being passed to
to_usb_device_driver() but were not catching this. Change the macro to
properly propagate the const-ness of the pointer so that we will notice
when we try to write to memory that we shouldn't be writing to.
This requires fixing up the usb_driver_applicable() function as well,
because it can handle a const * to struct usb_driver.
Cc: Johan Hovold <johan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111342-lagoon-reapprove-5e49@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out that we have some const pointers being passed to
to_usb_driver() but were not catching this. Change the macro to
properly propagate the const-ness of the pointer so that we will notice
when we try to write to memory that we shouldn't be writing to.
This requires fixing up the usb_match_dynamic_id() function as well,
because it can handle a const * to struct usb_driver.
Cc: Johan Hovold <johan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111339-shaky-goldsmith-b233@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When walking the list of dynamic ids for a driver, no lock was being
held, which meant that an id could be removed or added while the list
was being iterated. Fix this up by properly grabing the lock while we
walk the list.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111324-tubby-facecloth-d4a0@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a number of places where we accidentally pass in a constant
structure to later cast it off to a dynamic one, and then attempt to
grab a lock on it, which is not a good idea. To help resolve this, move
the dynamic id lock out of the dynamic id structure for the driver and
into one single lock for all USB dynamic ids. As this lock should never
have any real contention (it's only every accessed when a device is
added or removed, which is always serialized) there should not be any
difference except for some memory savings.
Note, this just converts the existing use of the dynamic id lock to the
new static lock, there is one place that is accessing the dynamic id
list without grabbing the lock, that will be fixed up in a follow-on
change.
Cc: Johan Hovold <johan@kernel.org>
Cc: Herve Codina <herve.codina@bootlin.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111322-kindly-finalist-d247@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure type safety by using min_t() instead of min().
Also add the explicit `unsigned int` as scripts/checkpatch.pl warns about:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20241112155817.3512577-5-snovitoll@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few places in the kernel where PCI IDs for different Cadence
USB controllers are being used. Besides different naming, they duplicate
each other. Make this all in order by providing common definitions via
PCI IDs database and use in all users. While doing that, rename
definitions as Roger suggested.
Suggested-by: Roger Quadros <rogerq@kernel.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20241112160125.2340972-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently if the maximum-speed is set to Super Speed for a 3.1 Gen2
capable controller, the FORCE_GEN1 bit of LLUCTL register is set only
for one SuperSpeed port (or the first port) present. Modify the logic
to set the FORCE_GEN1 bit for all ports if speed is being limited to
Gen-1.
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241112182018.199392-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing implementation of the TxFIFO resizing logic only supports
scenarios where more than one port RAM is used. However, there is a need
to resize the TxFIFO in USB2.0-only mode where only a single port RAM is
available. This commit introduces the necessary changes to support
TxFIFO resizing in such scenarios by adding a missing check for single
port RAM.
This fix addresses certain platform configurations where the existing
TxFIFO resizing logic does not work properly due to the absence of
support for single port RAM. By adding this missing check, we ensure
that the TxFIFO resizing logic works correctly in all scenarios,
including those with a single port RAM.
Fixes: 9f607a309f ("usb: dwc3: Resize TX FIFOs to meet EP bursting requirements")
Cc: stable@vger.kernel.org # 6.12.x: fad16c82: usb: dwc3: gadget: Refine the logic for resizing Tx FIFOs
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241112044807.623-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "command" variable can be controlled by the user via debugfs. The
worry is that if con_index is zero then "&uc->ucsi->connector[con_index
- 1]" would be an array underflow.
Fixes: 170a6726d0 ("usb: typec: ucsi: add support for separate DP altmode devices")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/c69ef0b3-61b0-4dde-98dd-97b97f81d912@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some Lenovo platforms, the patch works around problems with ov2740
sensor initialization, which manifest themself like below:
[ 4.540476] ov2740 i2c-INT3474:01: error -EIO: failed to find sensor
[ 4.542066] ov2740 i2c-INT3474:01: probe with driver ov2740 failed with error -5
or
[ 7.742633] ov2740 i2c-INT3474:01: chip id mismatch: 2740 != 0
[ 7.742638] ov2740 i2c-INT3474:01: error -ENXIO: failed to find sensor
and also by random failures of video stream start.
Issue can be reproduced by this script:
n=0
k=0
while [ $n -lt 50 ] ; do
sudo modprobe -r ov2740
sleep `expr $RANDOM % 5`
sudo modprobe ov2740
if media-ctl -p | grep -q ov2740 ; then
let k++
fi
let n++
done
echo Success rate $k/$n
Without the patch, success rate is approximately 15 or 50 tries.
With the patch it does not fail.
This problem is some hardware or firmware malfunction, that can not be
easy debug and fix. While setting small autosuspend delay is not perfect
workaround as user can configure it to any value, it will prevent
the failures by default.
Additionally setting small autosuspend delay should have positive effect
on power consumption as for most ljca workloads device is used for just
a few milliseconds flowed by long periods of at least 100ms of inactivity
(usually more).
Fixes: acd6199f19 ("usb: Add support for Intel LJCA device")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com> # ThinkPad X1 Yoga Gen 8, ov2740
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://lore.kernel.org/r/20241112075514.680712-2-stanislaw.gruszka@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not mark interface as ready to suspend when we are still waiting
for response messages from the device.
Fixes: acd6199f19 ("usb: Add support for Intel LJCA device")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com> # ThinkPad X1 Yoga Gen 8, ov2740
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://lore.kernel.org/r/20241112075514.680712-1-stanislaw.gruszka@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dtbinding have imx7ulp and imx8ulp compatible with imx7d before. And
then the dtb follow the dtbinding. However, the driver doesn't add imx8ulp
compatible now. To make imx8ulp work well, this will add support for it.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20241111090916.1534047-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GET_CAPABILITY size is wrong. The definitions for the
command sizes are for bitfieds and therefore in bits, not
bytes.
This fixes an issue that prevents the interface from being
registered with UCSI versions older than 2.0 because the
command size exceeds the MESSAGE_IN field size.
Fixes: 226ff2e681 ("usb: typec: ucsi: Convert connector specific commands to bitmaps")
Reported-by: Abel Vesa <abel.vesa@linaro.org>
Closes: https://lore.kernel.org/linux-usb/Zy864W7sysWZbCTd@linaro.org/
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241111100220.1743872-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a possibility that a request's callback could be invoked from
usb_ep_queue() (call trace below, supplemented with missing calls):
req->complete from usb_gadget_giveback_request
(drivers/usb/gadget/udc/core.c:999)
usb_gadget_giveback_request from musb_g_giveback
(drivers/usb/musb/musb_gadget.c:147)
musb_g_giveback from rxstate
(drivers/usb/musb/musb_gadget.c:784)
rxstate from musb_ep_restart
(drivers/usb/musb/musb_gadget.c:1169)
musb_ep_restart from musb_ep_restart_resume_work
(drivers/usb/musb/musb_gadget.c:1176)
musb_ep_restart_resume_work from musb_queue_resume_work
(drivers/usb/musb/musb_core.c:2279)
musb_queue_resume_work from musb_gadget_queue
(drivers/usb/musb/musb_gadget.c:1241)
musb_gadget_queue from usb_ep_queue
(drivers/usb/gadget/udc/core.c:300)
According to the docstring of usb_ep_queue(), this should not happen:
"Note that @req's ->complete() callback must never be called from within
usb_ep_queue() as that can create deadlock situations."
In fact, a hardware lockup might occur in the following sequence:
1. The gadget is initialized using musb_gadget_enable().
2. Meanwhile, a packet arrives, and the RXPKTRDY flag is set, raising an
interrupt.
3. If IRQs are enabled, the interrupt is handled, but musb_g_rx() finds an
empty queue (next_request() returns NULL). The interrupt flag has
already been cleared by the glue layer handler, but the RXPKTRDY flag
remains set.
4. The first request is enqueued using usb_ep_queue(), leading to the call
of req->complete(), as shown in the call trace above.
5. If the callback enables IRQs and another packet is waiting, step (3)
repeats. The request queue is empty because usb_g_giveback() removes the
request before invoking the callback.
6. The endpoint remains locked up, as the interrupt triggered by hardware
setting the RXPKTRDY flag has been handled, but the flag itself remains
set.
For this scenario to occur, it is only necessary for IRQs to be enabled at
some point during the complete callback. This happens with the USB Ethernet
gadget, whose rx_complete() callback calls netif_rx(). If called in the
task context, netif_rx() disables the bottom halves (BHs). When the BHs are
re-enabled, IRQs are also enabled to allow soft IRQs to be processed. The
gadget itself is initialized at module load (or at boot if built-in), but
the first request is enqueued when the network interface is brought up,
triggering rx_complete() in the task context via ioctl(). If a packet
arrives while the interface is down, it can prevent the interface from
receiving any further packets from the USB host.
The situation is quite complicated with many parties involved. This
particular issue can be resolved in several possible ways:
1. Ensure that callbacks never enable IRQs. This would be difficult to
enforce, as discovering how netif_rx() interacts with interrupts was
already quite challenging and u_ether is not the only function driver.
Similar "bugs" could be hidden in other drivers as well.
2. Disable MUSB interrupts in musb_g_giveback() before calling the callback
and re-enable them afterwars (by calling musb_{dis,en}able_interrupts(),
for example). This would ensure that MUSB interrupts are not handled
during the callback, even if IRQs are enabled. In fact, it would allow
IRQs to be enabled when releasing the lock. However, this feels like an
inelegant hack.
3. Modify the interrupt handler to clear the RXPKTRDY flag if the request
queue is empty. While this approach also feels like a hack, it wastes
CPU time by attempting to handle incoming packets when the software is
not ready to process them.
4. Flush the Rx FIFO instead of calling rxstate() in musb_ep_restart().
This ensures that the hardware can receive packets when there is at
least one request in the queue. Once IRQs are enabled, the interrupt
handler will be able to correctly process the next incoming packet
(eventually calling rxstate()). This approach may cause one or two
packets to be dropped (two if double buffering is enabled), but this
seems to be a minor issue, as packet loss can occur when the software is
not yet ready to process them. Additionally, this solution makes the
gadget driver compliant with the rule mentioned in the docstring of
usb_ep_queue().
There may be additional solutions, but from these four, the last one has
been chosen as it seems to be the most appropriate, as it addresses the
"bad" behavior of the driver.
Fixes: baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
Cc: stable@vger.kernel.org
Signed-off-by: Hubert Wiśniewski <hubert.wisniewski.25632@gmail.com>
Link: https://lore.kernel.org/r/4ee1ead4525f78fb5909a8cbf99513ad0082ad21.camel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of checking if any of the USB-C ports have orientation GPIO and
thus is orientation-aware, check for the GPIO for the port being
registered. There are no boards that are affected by this change at this
moment, so the patch is not marked as a fix, but it might affect other
boards in future.
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241109-ucsi-glue-fixes-v2-2-8b21ff4f9fbe@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI connector's indices start from 1 up to 3, PMIC_GLINK_MAX_PORTS.
Correct the condition in the pmic_glink_ucsi_connector_status()
callback, fixing Type-C orientation reporting for the third USB-C
connector.
Fixes: 76716fd5bf ("usb: typec: ucsi: glink: move GPIO reading into connector_status callback")
Cc: stable@vger.kernel.org
Reported-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241109-ucsi-glue-fixes-v2-1-8b21ff4f9fbe@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After an initial range change on the insigned int alt being > 1
the only possible values for alt are 0 or 1. Therefore the else
statement for values other than 0 or 1 is redundant and can be
removed. Replace the else if (all == 1) check with just an else.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/5f54ffd0-b5fe-4203-a626-c166becad362@gmail.com
Link: https://lore.kernel.org/r/20241107133348.22762-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for a long-standing use-after-free in an io_edgeport debug
printk and some new modem device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZy29qQAKCRALxc3C7H1l
CKN8AP9hD+7glW6sf0JDJ3zcN9vPIn1NLqALMil7Ga8hrmy2wQD/ff/mBrJqugF+
pQ1nFCQzLR2LtQEWRm/5ebb9yeaE1gE=
=3wbn
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.12-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 6.12-rc7
Here's a fix for a long-standing use-after-free in an io_edgeport debug
printk and some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.12-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: add support for Sierra Wireless EM86xx
USB: serial: io_edgeport: fix use after free in debug printk
USB: serial: option: add Quectel RG650V
USB: serial: option: add Fibocom FG132 0x0112 composition
Our static checker found a bug where set_serial_info() uses a mutex, but
get_serial_info() does not. Fortunately, the impact of this is relatively
minor. It doesn't cause a crash or any other serious issues. However, if a
race condition occurs between set_serial_info() and get_serial_info(),
there is a chance that the data returned by get_serial_info() will be
inconsistent.
Fixes: 3ae36bed3a ("fdti_sio: switch to ->[sg]et_serial()")
Signed-off-by: Qiu-ji Chen <chenqiuji666@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
That allows the fields in those command data structures to
be easily validated. If an unsupported field is accessed, a
warning is generated.
This will not force UCSI version checks to be made in every
place where these data structures are accessed, but it will
make it easier to pinpoint issues that are caused by the
unconditional accesses to those fields, and perhaps more
importantly, allow those issues to be noticed immediately.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241106150605.1017744-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are apparently incomplete clones of the HXD type chip in use.
Those return -EPIPE on GET_LINE_REQUEST and BREAK_REQUEST. Avoid
flooding the kernel log with those errors. Detect them during startup
and then use the line_settings cache instead of GET_LINE_REQUEST. Signal
missing break support via -ENOTTY.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
[ johan: fix macro prefix, drop oom error message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Stop Endpoint command on an already stopped endpoint fails and may be
misinterpreted as a known hardware bug by the completion handler. This
results in an unnecessary delay with repeated retries of the command.
Avoid queuing this command when endpoint state flags indicate that it's
stopped or halted and the command will fail. If commands are pending on
the endpoint, their completion handlers will process cancelled TDs so
it's done. In case of waiting for external operations like clearing TT
buffer, the endpoint is stopped and cancelled TDs can be processed now.
This eliminates practically all unnecessary retries because an endpoint
with pending URBs is maintained in Running state by the driver, unless
aforementioned commands or other operations are pending on it. This is
guaranteed by xhci_ring_ep_doorbell() and by the fact that it is called
every time any of those operations completes.
The only known exceptions are hardware bugs (the endpoint never starts
at all) and Stream Protocol errors not associated with any TRB, which
cause an endpoint reset not followed by restart. Sounds like a bug.
Generally, these retries are only expected to happen when the endpoint
fails to start for unknown/no reason, which is a worse problem itself,
and fixing the bug eliminates the retries too.
All cases were tested and found to work as expected. SET_DEQ_PENDING
was produced by patching uvcvideo to unlink URBs in 100us intervals,
which then runs into this case very often. EP_HALTED was produced by
restarting 'cat /dev/ttyUSB0' on a serial dongle with broken cable.
EP_CLEARING_TT by the same, with the dongle on an external hub.
Fixes: fd9d55d190 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-34-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_invalidate_cancelled_tds() may not work correctly if the hardware
is modifying endpoint or stream contexts at the same time by executing
a Set TR Dequeue command. And even if it worked, it would be unable to
queue Set TR Dequeue for the next stream, failing to clear xHC cache.
On stream endpoints, a chain of Set TR Dequeue commands may take some
time to execute and we may want to cancel more TDs during this time.
Currently this leads to Stop Endpoint completion handler calling this
function without testing for SET_DEQ_PENDING, which will trigger the
aforementioned problems when it happens.
On all endpoints, a halt condition causes Reset Endpoint to be queued
and an error status given to the class driver, which may unlink more
URBs in response. Stop Endpoint is queued and its handler may execute
concurrently with Set TR Dequeue queued by Reset Endpoint handler.
(Reset Endpoint handler calls this function too, but there seems to
be no possibility of it running concurrently with Set TR Dequeue).
Fix xhci_invalidate_cancelled_tds() to work correctly under a pending
Set TR Dequeue. Bail out of the function when SET_DEQ_PENDING is set,
then make the completion handler call the function again and also call
xhci_giveback_invalidated_tds(), which needs to be called next.
This seems to fix another potential bug, where the handler would call
xhci_invalidate_cancelled_tds(), which may clear some deferred TDs if
a sanity check fails, and the TDs wouldn't be given back promptly.
Said sanity check seems to be wrong and prone to false positives when
the endpoint halts, but fixing it is beyond the scope of this change,
besides ensuring that cleared TDs are given back properly.
Fixes: 5ceac4402f ("xhci: Handle TD clearing for multiple streams case")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-33-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some host controllers fail to atomically transition an endpoint to the
Running state on a doorbell ring and enter a hidden "Restarting" state,
which looks very much like Stopped, with the important difference that
it will spontaneously transition to Running anytime soon.
A Stop Endpoint command queued in the Restarting state typically fails
with Context State Error and the completion handler sees the Endpoint
Context State as either still Stopped or already Running. Even a case
of Halted was observed, when an error occurred right after the restart.
The Halted state is already recovered from by resetting the endpoint.
The Running state is handled by retrying Stop Endpoint.
The Stopped state was recognized as a problem on NEC controllers and
worked around also by retrying, because the endpoint soon restarts and
then stops for good. But there is a risk: the command may fail if the
endpoint is "stopped for good" already, and retries will fail forever.
The possibility of this was not realized at the time, but a number of
cases were discovered later and reproduced. Some proved difficult to
deal with, and it is outright impossible to predict if an endpoint may
fail to ever start at all due to a hardware bug. One such bug (albeit
on ASM3142, not on NEC) was found to be reliably triggered simply by
toggling an AX88179 NIC up/down in a tight loop for a few seconds.
An endless retries storm is quite nasty. Besides putting needless load
on the xHC and CPU, it causes URBs never to be given back, paralyzing
the device and connection/disconnection logic for the whole bus if the
device is unplugged. User processes waiting for URBs become unkillable,
drivers and kworker threads lock up and xhci_hcd cannot be reloaded.
For peace of mind, impose a timeout on Stop Endpoint retries in this
case. If they don't succeed in 100ms, consider the endpoint stopped
permanently for some reason and just give back the unlinked URBs. This
failure case is rare already and work is under way to make it rarer.
Start this work today by also handling one simple case of race with
Reset Endpoint, because it costs just two lines to implement.
Fixes: fd9d55d190 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-32-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code which it is referencing does not exist in the same function,
or the file for that matter. Since it was added [1], the Interrupter
Moderation Interval can be changed within xhci addon, e.g. PCI
xhci_pci_setup().
[1], commit 0ebbab3742 ("USB: xhci: Ring allocation and initialization.")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-31-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add xhci_dequeue_td() helper function to reduce code duplication.
Function xhci_dequeue_td() advances the dequeue pointer past the specified
Transfer Descriptor (TD) and releases the TD.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-30-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function is modified to return 'void' instead of an integer since it
invariably returns '0'. Additionally, multiple functions which only
return xhci_td_cleanup() are also refactored to return void.
This change eliminates the need for callers to handle a return value that
does not convey meaningful information and improve code readability, as it
becomes immediately clear that the function does not produce a significant
output.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-29-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function td_to_noop() does not utilize arguments 'xhci' and 'ep_ring'.
These unused arguments are removed to clean up the code.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-28-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant TRB cycle reset, the TRB cycle is already set to zero by
the preceding memset(), making the explicit reset unnecessary.
Clarify ring loop start point. Change the loop start from the dequeue
segment to the start segment. Both approaches achieve the same result,
but starting from the start segment makes it clearer that the entire ring
is being zeroed out.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-27-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'max_interrupters' contains the maximum supported interrupters
or the maximum interrupters the user has requested. Thus, it should be
used instead of HCS_MAX_INTRS().
User set 'max_interrupters' value is validated in xhci_gen_setup(),
otherwise 'max_interrupters' value is 'HCS_MAX_INTRS(xhci->hcs_params1)'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-26-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This quirk is old and seldom seen, as a result the trace is changed
to debug message and only printed when the quirk is set.
Move it into xhci_gen_setup() where the majority of quirks are set.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-25-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old names:
* start_seg - last_trb_seg
* first_trb - last_trb
New names:
* start_seg - end_seg
* start_trb - end_trb
A Transfer Descriptor (TD) in the xhci driver is a data structure that
represents a single transaction to be performed by the USB host controller.
This transaction is defined by TRBs from 'start_trb' in 'start_seg' to
'end_trb' in 'end_seg'.
The terms "start" and "end" were chosen over "first" and "last" for ease
of searching within the codebase. The ring structure uses 'first_seg' and
'last_seg', while the TD structure uses 'start_seg' and 'end_seg'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-24-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definitions of vendor IDs follow the pattern PCI_VENDOR_ID_#vendor,
while device IDs — PCI_DEVICE_ID_#vendor_#device.
Update the ETRON device IDs to follow the above mentioned pattern.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit f8f80be501 ("xhci: Use soft retry to recover faster from
transaction errors"), unplugging USB device while enumeration results in
errors like this:
[ 364.855321] xhci_hcd 0000:0b:00.0: ERROR Transfer event for disabled endpoint slot 5 ep 2
[ 364.864622] xhci_hcd 0000:0b:00.0: @0000002167656d70 67f03000 00000021 0c000000 05038001
[ 374.934793] xhci_hcd 0000:0b:00.0: Abort failed to stop command ring: -110
[ 374.958793] xhci_hcd 0000:0b:00.0: xHCI host controller not responding, assume dead
[ 374.967590] xhci_hcd 0000:0b:00.0: HC died; cleaning up
[ 374.973984] xhci_hcd 0000:0b:00.0: Timeout while waiting for configure endpoint command
Seems that Etorn xHCI host can not perform Soft Retry correctly, apply
XHCI_NO_SOFT_RETRY quirk to disable Soft Retry and then issue is gone.
This patch depends on commit a4a251f8c2 ("usb: xhci: do not perform
Soft Retry for some xHCI hosts").
Fixes: f8f80be501 ("xhci: Use soft retry to recover faster from transaction errors")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Performing a stability stress test on a USB3.0 2.5G ethernet adapter
results in errors like this:
[ 91.441469] r8152 2-3:1.0 eth3: get_registers -71
[ 91.458659] r8152 2-3:1.0 eth3: get_registers -71
[ 91.475911] r8152 2-3:1.0 eth3: get_registers -71
[ 91.493203] r8152 2-3:1.0 eth3: get_registers -71
[ 91.510421] r8152 2-3:1.0 eth3: get_registers -71
The r8152 driver will periodically issue lots of control-IN requests
to access the status of ethernet adapter hardware registers during
the test.
This happens when the xHCI driver enqueue a control TD (which cross
over the Link TRB between two ring segments, as shown) in the endpoint
zero's transfer ring. Seems the Etron xHCI host can not perform this
TD correctly, causing the USB transfer error occurred, maybe the upper
driver retry that control-IN request can solve problem, but not all
drivers do this.
| |
-------
| TRB | Setup Stage
-------
| TRB | Link
-------
-------
| TRB | Data Stage
-------
| TRB | Status Stage
-------
| |
To work around this, the xHCI driver should enqueue a No Op TRB if
next available TRB is the Link TRB in the ring segment, this can
prevent the Setup and Data Stage TRB to be breaked by the Link TRB.
Check if the XHCI_ETRON_HOST quirk flag is set before invoking the
workaround in xhci_queue_ctrl_tx().
Fixes: d0e96f5a71 ("USB: xhci: Control transfer support.")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes the hub driver does not recognize the USB device connected
to the external USB2.0 hub when the system resumes from S4.
After the SetPortFeature(PORT_RESET) request is completed, the hub
driver calls the HCD reset_device callback, which will issue a Reset
Device command and free all structures associated with endpoints
that were disabled.
This happens when the xHCI driver issue a Reset Device command to
inform the Etron xHCI host that the USB device associated with a
device slot has been reset. Seems that the Etron xHCI host can not
perform this command correctly, affecting the USB device.
To work around this, the xHCI driver should obtain a new device slot
with reference to commit 651aaf36a7 ("usb: xhci: Handle USB transaction
error on address command"), which is another way to inform the Etron
xHCI host that the USB device has been reset.
Add a new XHCI_ETRON_HOST quirk flag to invoke the workaround in
xhci_discover_or_reset_device().
Fixes: 2a8f82c4ce ("USB: xhci: Notify the xHC when a device is reset.")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Combine two if statements, because these hosts have the same
quirk flags applied.
[Mathias: has stable tag because other fixes in series depend on this]
Fixes: 91f7a1524a ("xhci: Apply broken streams quirk to Etron EJ188 xHCI host")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A ring consists of a list of segments, each containing a specific number of
TRBs. The xhci driver allocates and initializes ring segments and TRBs in
the same functions. This combined allocation and initialization process
leads to an issue where, after hibernation (S4 state), the xhci driver
frees all its memory and re-creates the rings, segments, and TRBs from
scratch.
Move all default ring segment initialization into function
xhci_initialize_ring_segments(). This function can be called to
reinitialize a ring without freeing and reallocating it.
Since xhci_alloc_segments_for_ring() no longer initializes segment TRBs,
xhci_initialize_ring_segments() is added to xhci_ring_expansion(). This
results in the last segment of the source ring having the 'LINK_TOGGLE'
bit set. Therefore, if the last source ring segment is not the last in
the destination ring, the 'LINK_TOGGLE' bit must be cleared.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for splitting ring segments allocation and initialization by
reworking the xhci_link_segments() function. Segment linking and ring type
checks are moved out of xhci_link_segments(), and the function is renamed
to "xhci_set_link_trb()".
The goal is to keep ring linking within xhci_alloc_segments_for_ring() and
move initialization into a separate function.
Additionally, reorder and simplify xhci_set_link_trb() for better
readability.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the xhci_link_rings() function to accept two rings: a source ring
and a destination ring. Previously, the function accepted a ring and a
segment list as arguments, now the function splices the source ring segment
list into the destination ring. This new approach reduces the number of
arguments and simplifies the code, making it easier to follow.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The segment list is only relevant within the context of the ring.
Thus, it is more logical to pass the ring itself when freeing all segments
from a ring, rather than passing the ring list.
Rename the function to "xhci_ring_segments_free" to align with the naming
convention of xhci_segment_free().
To make the freeing process more intuitive, free segments sequentially
from start to end (i.e., 0, 1, 2, 3, ...) instead of freeing the first
segment last (i.e., 1, 2, 3, ... 0).
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function xhci_alloc_segments_for_ring() currently takes 7 arguments,
5 of which are components of the 'xhci_ring' struct. Refactor the function
to accept a pointer to the 'xhci_ring' struct instead of passing these
components separately.
The change reduces the number of arguments, making the function signature
cleaner and easier to understand.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TRB cycle bit indicates TRB ownership by the Host Controller (HC) or
Host Controller Driver (HCD). New rings are initialized with 'cycle_state'
equal to one, and all its TRBs' cycle bits are set to zero. When handling
ring expansion, set the source ring cycle bits to the same value as the
destination ring.
Move the cycle bit setting from xhci_segment_alloc() to xhci_link_rings(),
and remove the 'cycle_state' argument from xhci_initialize_ring_info().
The xhci_segment_alloc() function uses kzalloc_node() to allocate segments,
ensuring that all TRB cycle bits are initialized to zero.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add macro to streamline and standardize the iteration over ring
segment list.
xhci_for_each_ring_seg(): Iterates over the entire ring segment list.
The xhci_free_segments_for_ring() function's while loop has not been
updated to use the new macro. This function has some underlying issues,
and as a result, it will be handled separately in a future patch.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ring data structure of each xHCI endpoint might stop sending
data due to the virt endpoint state.
Show the virt endpoint state within the endpoint context via debugfs
to facilitate debugging.
Co-developed-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A successful 'Set TR Deq' command writes a new dequeue pointer to the
stream context for stream rings, show the content of the stream ctx
at command completion.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Show stream id, stream context type (SCT), ring dequeue pointer and
the DMA address of the stream context during stream allocation
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't trace ring pointers every time driver increases enqueue pointer
after queuing a TRB, or dequeue pointer after handling an event.
These xhci_inc_deq: and xhci_inc_enq: trace entries fill up the trace and
provides little useful info now that the TRB DMA address is printed with
the TRB itself.
Only trace ring during xhci_inc_enq() and xhci_inc_deq() in case we move
to a new ring segment.
Also don't show both segment and TRB addess in trace.
Segment is just TRB with 0xfff masked off.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA address of a queued TRB is essential when looking at traces as
both transfer events and command completion events refer to the command
or transfer based on its DMA address.
Previously the TRB address was figured out from xhci_inc_enq and
xhci_inc_deq trace entries seen after queuing or handlong a TRB.
Now that DMA address is shown in TRB tracing we can get rid of most of the
xhci_inc_enq and xhci_inc_deq traces thus decreasing trace size.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is supposed to sum the lengths of all transfer TRBs in
a TD up to a point, but it starts summing at the current dequeue since
it only ever gets called on the first pending TD.
This won't work when there are cancelled TDs at the beginning of the
ring. The function tries to exclude No-Ops from the count, but not all
cancelled TDs are No-Op'ed - not those the HW stopped on.
The absolutely obvious fix is to start counting at the TD's first TRB.
And remove the now-useless 'ring' parameter, and 'xhci' too.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function has two parameters which it doesn't use and hasn't ever
used. One caller even puts NULL there, knowing it will work anyway.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In addition to Normal TRB fields the Isoch TRBs have a SIA flag,
Frame ID, TLBPC and TBC fields.
Add these fields to tracing output
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The is_bin_visible() callbacks should not modify the struct
bin_attribute passed as argument.
Enforce this by marking the argument as const.
As there are not many callback implementers perform this change
throughout the tree at once.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20241103-sysfs-const-bin_attr-v2-5-71110628844c@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "*cmd" variable can be controlled by the user via debugfs. That means
"new_cam" can be as high as 255 while the size of the uc->updated[] array
is UCSI_MAX_ALTMODES (30).
The call tree is:
ucsi_cmd() // val comes from simple_attr_write_xsigned()
-> ucsi_send_command()
-> ucsi_send_command_common()
-> ucsi_run_command() // calls ucsi->ops->sync_control()
-> ucsi_ccg_sync_control()
Fixes: 170a6726d0 ("usb: typec: ucsi: add support for separate DP altmode devices")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/325102b3-eaa8-4918-a947-22aca1146586@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device was already runtime suspended then during system suspend
we cannot access the device registers else it will crash.
Also we cannot access any registers after dwc3_core_exit() on some
platforms so move the dwc3_enable_susphy() call to the top.
Cc: stable@vger.kernel.org # v5.15+
Reported-by: William McVicker <willmcvicker@google.com>
Closes: https://lore.kernel.org/all/ZyVfcUuPq56R2m1Y@google.com
Fixes: 705e3ce37b ("usb: dwc3: core: Fix system suspend on TI AM62 platforms")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241104-am62-lpm-usb-fix-v1-1-e93df73a4f0d@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the read of USB_PDPHY_RX_ACKNOWLEDGE_REG failed, then hdr_len and
txbuf_len are uninitialized. This commit stops to print uninitialized
value and misleading/false data.
Cc: stable@vger.kernel.org
Fixes: a4422ff221 (" usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Signed-off-by: Rex Nie <rex.nie@jaguarmicro.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20241030133632.2116-1-rex.nie@jaguarmicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6ed05c68cb ("usb: musb: sunxi: Explicitly release USB PHY on
exit") will cause that usb phy @glue->xceiv is accessed after released.
1) register platform driver @sunxi_musb_driver
// get the usb phy @glue->xceiv
sunxi_musb_probe() -> devm_usb_get_phy().
2) register and unregister platform driver @musb_driver
musb_probe() -> sunxi_musb_init()
use the phy here
//the phy is released here
musb_remove() -> sunxi_musb_exit() -> devm_usb_put_phy()
3) register @musb_driver again
musb_probe() -> sunxi_musb_init()
use the phy here but the phy has been released at 2).
...
Fixed by reverting the commit, namely, removing devm_usb_put_phy()
from sunxi_musb_exit().
Fixes: 6ed05c68cb ("usb: musb: sunxi: Explicitly release USB PHY on exit")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241029-sunxi_fix-v1-1-9431ed2ab826@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of (of|device)_property_read_bool() for non-boolean properties
is deprecated in favor of of_property_present() when testing for
property presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241104190820.277702-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here as well, and this resolves a merge
conflict in:
drivers/usb/typec/tcpm/tcpm.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20241101150730.090dc30f@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit fde192511b ("kconfig: remove tristate choice support"),
all choice blocks are now boolean. There is no longer a need to specify
the choice type explicitly.
Most choice blocks already use "prompt". Before the next commit removes
support for the "bool" syntax in choice entries, this commit converts
the remaining "bool" occurences under drivers/usb/.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The TUSB1046-DCI is a USB-C linear redriver crosspoint switch, which can
mux SuperSpeed lanes from a Type-C connector to a USB3.0 data lane or up to
4 display port lanes.
Add support for driving the TUSB1046 as a Type-C orientation switch and
DisplayPort altmode multiplexer.
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241024-tusb1046-v2-2-d031b1a43e6d@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some PCIe-to-USB controllers such as TI's TUSB73x0 3.0 xHCI host
controller supports controlling the PWRONx polarity via the USB control
register (E0h). Add support for device tree property
ti,pwron-active-high which indicates PWRONx to be active high and
configure the E0h register accordingly. This enables the software
control for the TUSB73x0's PWRONx outputs with an inverted polarity from
the default configuration which could be used as USB EN signals for the
other hubs or devices.
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20241029072444.8827-3-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_gpio.h is deprecated and subject to remove. The drivers in question
don't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20241031103818.2451816-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "dev_dbg(&urb->dev->dev, ..." which happens after usb_free_urb(urb)
is a use after free of the "urb" pointer. Store the "dev" pointer at the
start of the function to avoid this issue.
Fixes: 984f686832 ("USB: serial: io_edgeport.c: remove dbg() usage")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
PD3.1 spec ("8.3.3.3.3 PE_SNK_Wait_for_Capabilities State") mandates
that the policy engine perform a hard reset when SinkWaitCapTimer
expires. Instead the code explicitly does a GET_SOURCE_CAP when the
timer expires as part of SNK_WAIT_CAPABILITIES_TIMEOUT. Due to this the
following compliance test failures are reported by the compliance tester
(added excerpts from the PD Test Spec):
* COMMON.PROC.PD.2#1:
The Tester receives a Get_Source_Cap Message from the UUT. This
message is valid except the following conditions: [COMMON.PROC.PD.2#1]
a. The check fails if the UUT sends this message before the Tester
has established an Explicit Contract
...
* TEST.PD.PROT.SNK.4:
...
4. The check fails if the UUT does not send a Hard Reset between
tTypeCSinkWaitCap min and max. [TEST.PD.PROT.SNK.4#1] The delay is
between the VBUS present vSafe5V min and the time of the first bit
of Preamble of the Hard Reset sent by the UUT.
For the purpose of interoperability, restrict the quirk introduced in
https://lore.kernel.org/all/20240523171806.223727-1-sebastian.reichel@collabora.com/
to only non self-powered devices as battery powered devices will not
have the issue mentioned in that commit.
Cc: stable@vger.kernel.org
Fixes: 122968f8dd ("usb: typec: tcpm: avoid resets for missing source capability messages")
Reported-by: Badhri Jagan Sridharan <badhri@google.com>
Closes: https://lore.kernel.org/all/CAPTae5LAwsVugb0dxuKLHFqncjeZeJ785nkY4Jfd+M-tCjHSnQ@mail.gmail.com/
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241024022233.3276995-1-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For devm_usb_put_phy(), its comment says it needs to invoke usb_put_phy()
to release the phy, but it does not do that actually, so it can not fully
undo what the API devm_usb_get_phy() does, that is wrong, fixed by using
devres_release() instead of devres_destroy() within the API.
Fixes: cedf860237 ("usb: phy: move bulk of otg/otg.c to phy/phy.c")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241020-usb_phy_fix-v1-1-7f79243b8e1e@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow the advice in Documentation/filesystems/sysfs.rst:
show() should only use sysfs_emit() or sysfs_emit_at() when formatting
the value to be returned to user space.
Signed-off-by: Jiayi Li <lijiayi@kylinos.cn>
Link: https://lore.kernel.org/r/20241023085429.2865488-1-lijiayi@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for DT time properties to allow users to define platform
specific timing deadlines of certain timers rather than using hardcoded
ones. For values that have not been explicitly defined in DT using this
property, default values will be set therefore, making this change
backward compatible.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241022-pd-dt-time-props-v1-2-fea96f51b302@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current logic is rigid, setting num_fifos to fixed values.
3 for any maxburst greater than 1.
tx_fifo_resize_max_num for maxburst greater than 6.
Additionally, it did not differentiate much between bulk and
isochronous transfers, applying similar logic to both.
The updated logic is more flexible and specifically designed to meet
the unique requirements of both bulk and isochronous transfers. We
have made every effort to satisfy all needs and requirements, verified
on our specific platform and application.
Bulk Transfers: Ensures that num_fifos is optimized by considering both
the maxburst and DT property "tx-fifo-max-num" for super speed and
above. For high-speed and below bulk endpoints, a 2K TxFIFO allocation
is used to meet efficient data transfer needs, considering
FIFO-constrained platforms.
Isochronous Transfers: Ensures that num_fifos is sufficient by
considering the maximum packet multiplier for HS and below and maxburst
for Super-speed and above eps, along with a constraint with the DT
property "tx-fifo-max-num".
This change aims to optimize the allocation of Tx FIFOs for both bulk
and isochronous endpoints, potentially improving data transfer efficiency
and overall performance. It also enhances support for all use cases,
which can be tweaked with DT parameters and the endpoint’s maxburst and
maxpacket. This structured approach ensures that the appropriate number
of FIFOs is allocated based on the endpoint type and USB speed.
Signed-off-by: Akash Kumar <quic_akakum@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241017064423.7056-1-quic_akakum@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That command is executed from several locations in the
driver, so providing a dedicated helper function for it.
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241017091112.1178509-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the __free() macro for 'altmodes_node' to automatically release the
node when it goes out of scope, removing the need for explicit calls to
fwnode_handle_put().
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241021-typec-class-fwnode_handle_put-v2-2-3281225d3d27@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'altmodes_node' fwnode_handle is never released after it is no
longer required, which leaks the resource.
Add the required call to fwnode_handle_put() when 'altmodes_node' is no
longer required.
Cc: stable@vger.kernel.org
Fixes: 7b458a4c5d ("usb: typec: Add typec_port_register_altmodes()")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20241021-typec-class-fwnode_handle_put-v2-1-3281225d3d27@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If drm_dp_hpd_bridge_register() fails, the probe function returns
without removing the fwnode via fwnode_handle_put(), leaking the
resource.
Jump to fwnode_remove if drm_dp_hpd_bridge_register() fails to remove
the fwnode acquired with device_get_named_child_node().
Cc: stable@vger.kernel.org
Fixes: 7d9f1b72b2 ("usb: typec: qcom-pmic-typec: switch to DRM_AUX_HPD_BRIDGE")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241020-qcom_pmic_typec-fwnode_remove-v2-2-7054f3d2e215@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The right function to release a fwnode acquired via
device_get_named_child_node() is fwnode_handle_put(), and not
fwnode_remove_software_node(), as no software node is being handled.
Replace the calls to fwnode_remove_software_node() with
fwnode_handle_put() in qcom_pmic_typec_probe() and
qcom_pmic_typec_remove().
Cc: stable@vger.kernel.org
Fixes: a4422ff221 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241020-qcom_pmic_typec-fwnode_remove-v2-1-7054f3d2e215@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a boot hang issue triggered when a USB3 device is incorrectly assumed
to be tunneled over USB4, thus attempting to create a device link between
the USB3 "consumer" device and the USB4 "supplier" Host Interface before
the USB4 side is properly bound to a driver.
This could happen if xhci isn't capable of detecting tunneled devices,
but ACPI tables contain all info needed to assume device is tunneled.
i.e. udev->tunnel_mode == USB_LINK_UNKNOWN.
It turns out that even for actual tunneled USB3 devices it can't be
assumed that the thunderbolt driver providing the tunnel is loaded
before the tunneled USB3 device is created.
The tunnel can be created by BIOS and remain in use by thunderbolt/USB4
host driver once it loads.
Solve this by making the device link "stateless", which doesn't create
a driver presence order dependency between the supplier and consumer
drivers.
It still guarantees correct suspend/resume and shutdown ordering.
cc: Mario Limonciello <mario.limonciello@amd.com>
Fixes: f1bfb4a6fe ("usb: acpi: add device link between tunneled USB3 device and USB4 Host Interface")
Tested-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241024131355.3836538-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit d483f034f0 ("usb: dwc2: Skip clock gating on Broadcom SoCs")
introduced a regression on Raspberry Pi 3 B Plus, which prevents
enumeration of the onboard Microchip LAN7800 in case no external USB device
is connected during boot.
Fixes: d483f034f0 ("usb: dwc2: Skip clock gating on Broadcom SoCs")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241025103621.4780-2-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the aborting of a command, the software receives a command
completion event for the command ring stopped, with the TRB pointing
to the next TRB after the aborted command.
If the command we abort is located just before the Link TRB in the
command ring, then during the 'command ring stopped' completion event,
the xHC gives the Link TRB in the event's cmd DMA, which causes a
mismatch in handling command completion event.
To address this situation, move the 'command ring stopped' completion
event check slightly earlier, since the specific command it stopped
on isn't of significant concern.
Fixes: 7f84eef0da ("USB: xhci: No-op command queueing and irq handler.")
Cc: stable@vger.kernel.org
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241022155631.1185-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use pm_runtime_put in the remove function and pm_runtime_get to disable
RPM on platforms that don't support runtime D3, as re-enabling it through
sysfs auto power control may cause the controller to malfunction. This
can lead to issues such as hotplug devices not being detected due to
failed interrupt generation.
Fixes: a5d6264b63 ("xhci: Enable RPM on controllers that support low-power states")
Cc: stable <stable@kernel.org>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241024133718.723846-1-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids.
Everything has been in linux-next over night with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZxIyrQAKCRALxc3C7H1l
CCgGAQDkVANkAOTEq8zOfpaULkWkMJXMRzd28YrkCqlgJfbkYQEAjTWtz8F48Ne7
V9CYj/dbNULlQ0Q+kqKqGBcKdZrq2AI=
=/sNu
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.12-rc4' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.12-rc4
Here are some new modem device ids.
Everything has been in linux-next over night with no reported issues.
* tag 'usb-serial-6.12-rc4' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit FN920C04 MBIM compositions
USB: serial: option: add support for Quectel EG916Q-GL
Treat each completed full size write to /dev/ttyDBC0 as a separate usb
transfer. Make sure the size of the TRBs matches the size of the tty
write by first queuing as many max packet size TRBs as possible up to
the last TRB which will be cut short to match the size of the tty write.
This solves an issue where userspace writes several transfers back to
back via /dev/ttyDBC0 into a kfifo before dbgtty can find available
request to turn that kfifo data into TRBs on the transfer ring.
The boundary between transfer was lost as xhci-dbgtty then turned
everyting in the kfifo into as many 'max packet size' TRBs as possible.
DbC would then send more data to the host than intended for that
transfer, causing host to issue a babble error.
Refuse to write more data to kfifo until previous tty write data is
turned into properly sized TRBs with data size boundaries matching tty
write size
Tested-by: Uday M Bhat <uday.m.bhat@intel.com>
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some host controllers fail to produce the final completion event on an
isochronous TD which experienced an error mid TD. We deal with it by
flagging such TDs and checking if the next event points at the flagged
TD or at the next one, and giving back the flagged TD if the latter.
This is not enough, because the next TD may be missed by the xHC. Or
there may be no next TD but a ring underrun. We also need to get such
TD quickly out of the way, or errors on later TDs may be handled wrong.
If the next TD experiences a Missed Service Error, we will set the skip
flag on the endpoint and then attempt skipping TDs when yet another
event arrives. In such scenario, we ought to report the 'error mid TD'
transfer as such rather than skip it.
Another problem case are Stopped events. If we see one after an error
mid TD, we naively assume that it's a Force Stopped Event because it
doesn't match the pending TD, but in reality it might be an ordinary
Stopped event for the next TD, which we fail to recognize and handle.
Fix this by moving error mid TD handling before the whole TD skipping
loop. Remove unnecessary conditions, always give back the TD if the new
event points to any TRB outside it or if the pointer is NULL, as may be
the case in Ring Underrun and Overrun events on 1st gen hardware. Only
if the pending TD isn't flagged, consider other actions like skipping.
As a side effect of reordering with skip and FSE cases, error mid TD is
reordered with last_td_was_short check. This is harmless, because the
two cases are mutually exclusive - only one can happen in any given run
of handle_tx_event().
Tested on the NEC host and a USB camera with flaky cable. Dynamic debug
confirmed that Transaction Errors are sometimes seen, sometimes mid-TD,
sometimes followed by Missed Service. In such cases, they were finished
properly before skipping began.
[Rebase on 6.12-rc1 -Mathias]
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid xHC host from processing a cancelled URB by always turning
cancelled URB TDs into no-op TRBs before queuing a 'Set TR Deq' command.
If the command fails then xHC will start processing the cancelled TD
instead of skipping it once endpoint is restarted, causing issues like
Babble error.
This is not a complete solution as a failed 'Set TR Deq' command does not
guarantee xHC TRB caches are cleared.
Fixes: 4db356924a ("xhci: turn cancelled td cleanup to its own function")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stream contex type (SCT) bitfield is used both in the stream context
data structure, and in the 'Set TR Dequeue pointer' command TRB.
In both cases it uses bits 3:1
The SCT_FOR_TRB(p) macro used to set the stream context type (SCT) field
for the 'Set TR Dequeue pointer' command TRB incorrectly shifts the value
1 bit left before masking the three bits.
Fix this by first masking and rshifting, just like the similar
SCT_FOR_CTX(p) macro does
This issue has not been visibile as the lost bit 3 is only used with
secondary stream arrays (SSA). Xhci driver currently only supports using
a primary stream array with Linear stream addressing.
Fixes: 95241dbdf8 ("xhci: Set SCT field for Set TR dequeue on streams")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer has been encountering "task hung" problems ever
since the dummy-hcd driver was changed to use hrtimers instead of
regular timers. It turns out that the problems are caused by a subtle
difference between the timer_pending() and hrtimer_active() APIs.
The changeover blindly replaced the first by the second. However,
timer_pending() returns True when the timer is queued but not when its
callback is running, whereas hrtimer_active() returns True when the
hrtimer is queued _or_ its callback is running. This difference
occasionally caused dummy_urb_enqueue() to think that the callback
routine had not yet started when in fact it was almost finished. As a
result the hrtimer was not restarted, which made it impossible for the
driver to dequeue later the URB that was just enqueued. This caused
usb_kill_urb() to hang, and things got worse from there.
Since hrtimers have no API for telling when they are queued and the
callback isn't running, the driver must keep track of this for itself.
That's what this patch does, adding a new "timer_pending" flag and
setting or clearing it at the appropriate times.
Reported-by: syzbot+f342ea16c9d06d80b585@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/6709234e.050a0220.3e960.0011.GAE@google.com/
Tested-by: syzbot+f342ea16c9d06d80b585@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: a7f3813e58 ("usb: gadget: dummy_hcd: Switch to hrtimer transfer scheduler")
Cc: Marcello Sylvester Bauer <sylv@sylv.io>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/2dab644e-ef87-4de8-ac9a-26f100b2c609@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expose xhci_stop_endpoint_sync() which is a synchronous variant of
xhci_queue_stop_endpoint(). This is useful for client drivers that are
using the secondary interrupters, and need to stop the current endpoint
session.
This does not go through the normal xhci_handle_cmd_stop_ep() command
completion handler, because it utilizes the completion path to achieve
synchronous behavior. Users of this API are primarily intended to be
clients that maintain their own transfer rings, such as in the case of USB
audio offload.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20241015212915.1206789-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the streamoff call was triggered by some previous disconnect
or userspace application shutdown the uvc_function_setup_continue
should not be called and the state should not be overwritten.
For this situation the set_alt(0) was never called and the streaming ep
has no USB_GADGET_DELAYED_STATUS pending.
Since the state then was already updated before we also omit the state
update.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-9-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is adding trace events for each request that is being
enqueued into the hw and will be completed. This way it is possible
to track the fill status of the gadget hardware and find potential
issues.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-8-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We set the minimum amount of v4l2 buffers that is possibly be pending
to UVCG_STREAMING_MIN_BUFFERS which is two. This way the driver will
always have at least one frame pending to be encoded while the other
is being enqueued in the hardware.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-7-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compressed formats generate content depending amount of data that is set
in the vb2 buffer by the payload_size. When streaming those formats it
is better to scatter that smaller data over all requests. This patch is
doing that by introducing the calculated req_payload_size which is
updated by each frame. It the uses this amount of data to fill the
isoc requests instead of the video->req_size.
For uncompressed formats it will not make a difference since the payload
size will be equal to the imagesize. Therefore the code will have no
effecta as req_payload_size will be equal to req_size.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-6-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is removing the initial imprecise and limited calculation of
requests needed to be used from the queue_setup callback. It instead
introduces the uvc_video_prep_requests function which is called
immediately before the request allocation.
With the information of the usb frame interval length it is possible to
calculate the number of requests needed during one frame duration.
Based on the calculated number of requests and the imagesize we
calculate the actual size per request. This calculation has the benefit
that the frame data is equally distributed over all allocated requests.
When the req_size is not in the range for the actually configured
max_req_size configured for the overall bandwidth we fallback
to use the max_req_size instead.
Since this calculations are only important for isoc transfers we just
use max_request_size for bulk and skip it.
As video->req_size will be recalculated on every video_enable resetting
it to 0 is not necessary anymore.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-5-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uvc gadget driver is lacking the information which frame interval
was set by the host. We add this information by implementing the g_parm
and s_parm callbacks.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-4-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We install an kthread with pfifo priority that is iterating over all
prepared requests and keeps the isoc queue busy. This way it will be
scheduled with the same priority as the interrupt handler.
As the kthread is triggered with video_enable it will immediately
queue some zero length requests into the hw if there is no buffer data
available. It also watches the level of needed zero length requests in
the hardware not to fall under the UVCG_REQ_MAX_ZERO_COUNT threshold.
This way we can drop the function uvc_video_ep_queue_initial_requests
entirely.
By using the kthread to do the actual request handling the interrupt
handler will not be running into the time consuming and eventually
locking work of actually enqueueing the requests back into its own
pipeline. This work can now even be scheduled on another cpu.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-3-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The complete handler will at least be called after 16 requests have
completed, but will still handle all finisher requests. Since we have
to maintain a costant filling in the isoc queue we ensure this by
adding zero length requests.
By counting the amount enqueued requests we can ensure that the queue is
never underrun and only need to get active if the queue is running
critical. This patch is setting 32 as the critical level, which
is twice the request amount that is needed to create interrupts.
To properly solve the amount of zero length requests that needs to
be held in the hardware after one interrupt needs to be measured
and depends on the runtime of the first enqueue run after the interrupt
triggered. For now we just use twice the amount of requests between an
interrupt.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-2-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the req_free list will updated if enqueuing one request was not
possible it will be added back to the free list. With every available
free request in the queue it is a valid case for the pump worker to use
it and continue the pending bufferdata into requests for the req_ready
list.
Fixes: 6acba0345b ("usb:gadget:uvc Do not use worker thread to pump isoc usb requests")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-1-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI does not share the contents of the Enter_USB Message
that was used, so the active mode still has to be always
determined from the enumerated USB device. However, after
UCSI v2.0 it is possible to check separately is USB4 the
active mode.
So with USB2 and USB3 the mode is always determined from the
result of the USB enumeration, and when USB4 USB Mode is
active, UCSI driver can assign the mode directly.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241016131834.898599-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB capabilities can be extracted from the response to
the Get Connector Capability command. USB2 and USB3 support
can be checked from the Operation Mode field, and USB4
support from the Extended Operation Mode field.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8450-HDK
Link: https://lore.kernel.org/r/20241016131834.898599-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This attribute file shows the supported USB modes (USB 2.0,
USB 3.0 and USB4) of the partner, and the currently active
mode.
The active mode is determined primarily by checking the
speed of the enumerated USB device. When USB Power Delivery
is supported, the active USB mode should be always the mode
that was used with the Enter_USB Message, regardless of the
result of the USB enumeration. The port drivers can
separately assign the mode with a dedicated API.
If USB Power Delivery Identity is supplied for the partner
device, the supported modes are extracted from it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241016131834.898599-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This attribute file, named "usb_capability", will show the
supported USB modes, which are USB 2.0, USB 3.2 and USB4.
These modes are defined in the USB Type-C (R2.0) and USB
Power Delivery (R3.0 V2.0) Specifications.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241016131834.898599-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbdev_mmap() creates VMAs which can only be used through
usbdev_do_ioctl(), which requires FMODE_WRITE; so usbdev_mmap() is only
useful with FMODE_WRITE.
On typical Linux systems, files at /dev/bus/usb/*/* are mode 0664, so
UIDs without any special privileges can't use usbdev_do_ioctl(), but
they can still execute the usbdev_mmap() codepath.
Check for FMODE_WRITE in usbdev_mmap() to reduce attack surface a little
bit.
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20241016-usbdev-mmap-require-write-v1-1-6f8256414d5c@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for frame-based frame format, which can be used to support
multiple formats like H264 or H265, in addition to MJPEG and YUV frames.
The frame-based format is set to H264 by default, but it can be updated
to other formats by modifying the GUID through the guid configfs
attribute. Different structures are used for all three formats, as
H264 has a different structure compared to MJPEG and uncompressed
formats. These structures will be passed to the frame make function
based on the active format, using a common frame structure with
additional parameters needed only for frame-based formats. These
parameters are handled at runtime in the UVC driver.
Signed-off-by: Akash Kumar <quic_akakum@quicinc.com>
Link: https://lore.kernel.org/r/20240927152138.31416-1-quic_akakum@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The configfs store callback should return the number of bytes consumed
not the total number of bytes we actually stored. These could differ if
for example the passed in string had a newline we did not store.
If the returned value does not match the number of bytes written the
writer might assume a failure or keep trying to write the remaining bytes.
For example the following command will hang trying to write the final
newline over and over again (tested on bash 2.05b):
echo foo > function_name
Fixes: 993a44fa85 ("usb: gadget: f_uac2: allow changing interface name via configfs")
Cc: stable <stable@kernel.org>
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Link: https://lore.kernel.org/r/20241006232637.4267-1-kgroeneveld@lenbrook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 6d73572206 ("usb: dwc3: core: Prevent phy suspend during init"),
system suspend is broken on AM62 TI platforms.
Before that commit, both DWC3_GUSB3PIPECTL_SUSPHY and DWC3_GUSB2PHYCFG_SUSPHY
bits (hence forth called 2 SUSPHY bits) were being set during core
initialization and even during core re-initialization after a system
suspend/resume.
These bits are required to be set for system suspend/resume to work correctly
on AM62 platforms.
Since that commit, the 2 SUSPHY bits are not set for DEVICE/OTG mode if gadget
driver is not loaded and started.
For Host mode, the 2 SUSPHY bits are set before the first system suspend but
get cleared at system resume during core re-init and are never set again.
This patch resovles these two issues by ensuring the 2 SUSPHY bits are set
before system suspend and restored to the original state during system resume.
Cc: stable@vger.kernel.org # v6.9+
Fixes: 6d73572206 ("usb: dwc3: core: Prevent phy suspend during init")
Link: https://lore.kernel.org/all/1519dbe7-73b6-4afc-bfe3-23f4f75d772f@kernel.org/
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20241011-am62-lpm-usb-v3-1-562d445625b5@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If USB virtualizatoin is enabled, USB2 ports are shared between all
Virtual Functions. The USB2 port number owned by an USB2 root hub in
a Virtual Function may be less than total USB2 phy number supported
by the Tegra XUSB controller.
Using total USB2 phy number as port number to check all PORTSC values
would cause invalid memory access.
[ 116.923438] Unable to handle kernel paging request at virtual address 006c622f7665642f
...
[ 117.213640] Call trace:
[ 117.216783] tegra_xusb_enter_elpg+0x23c/0x658
[ 117.222021] tegra_xusb_runtime_suspend+0x40/0x68
[ 117.227260] pm_generic_runtime_suspend+0x30/0x50
[ 117.232847] __rpm_callback+0x84/0x3c0
[ 117.237038] rpm_suspend+0x2dc/0x740
[ 117.241229] pm_runtime_work+0xa0/0xb8
[ 117.245769] process_scheduled_works+0x24c/0x478
[ 117.251007] worker_thread+0x23c/0x328
[ 117.255547] kthread+0x104/0x1b0
[ 117.259389] ret_from_fork+0x10/0x20
[ 117.263582] Code: 54000222 f9461ae8 f8747908 b4ffff48 (f9400100)
Cc: stable@vger.kernel.org # v6.3+
Fixes: a30951d31b ("xhci: tegra: USB2 pad power controls")
Signed-off-by: Henry Lin <henryl@nvidia.com>
Link: https://lore.kernel.org/r/20241014042134.27664-1-henryl@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 programming guide mentions that when operating in USB2.0 speeds,
if GUSB2PHYCFG[6] or GUSB2PHYCFG[8] is set, it must be cleared prior
to issuing commands and may be set again after the command completes.
But currently while issuing EndXfer command without CmdIOC set, we
wait for 1ms after GUSB2PHYCFG is restored. This results in cases
where EndXfer command doesn't get completed and causes SMMU faults
since requests are unmapped afterwards. Hence restore GUSB2PHYCFG
after waiting for EndXfer command completion.
Cc: stable@vger.kernel.org
Fixes: 1d26ba0944 ("usb: dwc3: Wait unconditionally after issuing EndXfer command")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240924093208.2524531-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This line is overwriting the result of the above switch-case.
This fixes the tcpm driver getting stuck in a "Sink TX No Go" loop.
Fixes: a4422ff221 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241005144146.2345-1-jonathan@marek.ca
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the extra semicolon after the
do {} while (0) in UVC_COPY_DESCRIPTOR macro.
Fix the following checkpatch.pl warning
WARNING: do {} while (0) macros should not be semicolon terminated
+#define UVC_COPY_DESCRIPTOR(mem, dst, desc) \
+ do { \
+ memcpy(mem, desc, (desc)->bLength); \
+ *(dst)++ = mem; \
+ mem += (desc)->bLength; \
+ } while (0);
Signed-off-by: Abhishek Tamboli <abhishektamboli9@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Link: https://lore.kernel.org/r/20241013142511.9946-1-abhishektamboli9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI _DSM methods are needed only for UCSI write operations and for reading
CCI during RESET_PPM operation. So, remove _DSM calls from other places.
While there, remove the Zenbook quirk also since the default behavior
now aligns with the Zenbook quirk. With this change, GET_CONNECTOR_STATUS
returns at least 6 seconds faster than before in Arrowlake-S platforms.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Reviewed-by: Christian A. Ehrhardt <lk@c--e.de>
Link: https://lore.kernel.org/r/20240830084342.460109-1-saranya.gopal@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While design wise the idea of converting the driver to use
the hierarchy of the IRQ chips is correct, the implementation
has (inherited) flaws. This was unveiled when platform_get_irq()
had started WARN() on IRQ 0 that is supposed to be a Linux
IRQ number (also known as vIRQ).
Rework the driver to respect IRQ domain when creating each MFD
device separately, as the domain is not the same for all of them.
Fixes: 9c6235c863 ("mfd: intel_soc_pmic_bxtwc: Add bxt_wcove_usbc device")
Fixes: d2061f9cc3 ("usb: typec: add driver for Intel Whiskey Cove PMIC USB Type-C PHY")
Fixes: 57129044f5 ("mfd: intel_soc_pmic_bxtwc: Use chained IRQs for second level IRQ chips")
Reported-by: Zhang Ning <zhangn1985@outlook.com>
Closes: https://lore.kernel.org/r/TY2PR01MB3322FEDCDC048B7D3794F922CDBA2@TY2PR01MB3322.jpnprd01.prod.outlook.com
Tested-by: Zhang Ning <zhangn1985@outlook.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20241005193029.1929139-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
Here are some small USB fixes for some reported problems for 6.12-rc3.
Include in here is:
- fix for yurex driver that was caused in -rc1
- build error fix for usbg network filesystem code
- onboard_usb_dev build fix
- dwc3 driver fixes for reported errors
- gadget driver fix
- new USB storage driver quirk
- xhci resume bugfix
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZwu6fw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yly6QCfdXwmKEqG4H7xonERzmEkP9/sYtoAnAsafKV5
5pWgy7Jw+WH1s1L7IzGy
=xrG1
-----END PGP SIGNATURE-----
Merge tag 'usb-6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for some reported problems for 6.12-rc3.
Include in here is:
- fix for yurex driver that was caused in -rc1
- build error fix for usbg network filesystem code
- onboard_usb_dev build fix
- dwc3 driver fixes for reported errors
- gadget driver fix
- new USB storage driver quirk
- xhci resume bugfix
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
net/9p/usbg: Fix build error
USB: yurex: kill needless initialization in yurex_read
Revert "usb: yurex: Replace snprintf() with the safer scnprintf() variant"
usb: xhci: Fix problem with xhci resume from suspend
usb: misc: onboard_usb_dev: introduce new config symbol for usb5744 SMBus support
usb: dwc3: core: Stop processing of pending events if controller is halted
usb: dwc3: re-enable runtime PM after failed resume
usb: storage: ignore bogus device raised by JieLi BR21 USB sound chip
usb: gadget: core: force synchronous registration
[Syzbot reported two possible deadlocks]
The first possible deadlock is:
WARNING: possible recursive locking detected
6.12.0-rc1-syzkaller-00027-g4a9fe2a8ac53 #0 Not tainted
--------------------------------------------
syz-executor363/2651 is trying to acquire lock:
ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_release+0x15d/0x2c0 drivers/usb/misc/chaoskey.c:322
but task is already holding lock:
ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_release+0x7f/0x2c0 drivers/usb/misc/chaoskey.c:299
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(chaoskey_list_lock);
lock(chaoskey_list_lock);
*** DEADLOCK ***
The second possible deadlock is:
WARNING: possible circular locking dependency detected
6.12.0-rc1-syzkaller-00027-g4a9fe2a8ac53 #0 Not tainted
------------------------------------------------------
kworker/0:2/804 is trying to acquire lock:
ffffffff899dadb0 (minor_rwsem){++++}-{3:3}, at: usb_deregister_dev+0x7c/0x1e0 drivers/usb/core/file.c:186
but task is already holding lock:
ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_disconnect+0xa8/0x2a0 drivers/usb/misc/chaoskey.c:235
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (chaoskey_list_lock){+.+.}-{3:3}:
__mutex_lock_common kernel/locking/mutex.c:608 [inline]
__mutex_lock+0x175/0x9c0 kernel/locking/mutex.c:752
chaoskey_open+0xdd/0x220 drivers/usb/misc/chaoskey.c:274
usb_open+0x186/0x220 drivers/usb/core/file.c:47
chrdev_open+0x237/0x6a0 fs/char_dev.c:414
do_dentry_open+0x6cb/0x1390 fs/open.c:958
vfs_open+0x82/0x3f0 fs/open.c:1088
do_open fs/namei.c:3774 [inline]
path_openat+0x1e6a/0x2d60 fs/namei.c:3933
do_filp_open+0x1dc/0x430 fs/namei.c:3960
do_sys_openat2+0x17a/0x1e0 fs/open.c:1415
do_sys_open fs/open.c:1430 [inline]
__do_sys_openat fs/open.c:1446 [inline]
__se_sys_openat fs/open.c:1441 [inline]
__x64_sys_openat+0x175/0x210 fs/open.c:1441
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
-> #0 (minor_rwsem){++++}-{3:3}:
check_prev_add kernel/locking/lockdep.c:3161 [inline]
check_prevs_add kernel/locking/lockdep.c:3280 [inline]
validate_chain kernel/locking/lockdep.c:3904 [inline]
__lock_acquire+0x250b/0x3ce0 kernel/locking/lockdep.c:5202
lock_acquire.part.0+0x11b/0x380 kernel/locking/lockdep.c:5825
down_write+0x93/0x200 kernel/locking/rwsem.c:1577
usb_deregister_dev+0x7c/0x1e0 drivers/usb/core/file.c:186
chaoskey_disconnect+0xb7/0x2a0 drivers/usb/misc/chaoskey.c:236
usb_unbind_interface+0x1e8/0x970 drivers/usb/core/driver.c:461
device_remove drivers/base/dd.c:569 [inline]
device_remove+0x122/0x170 drivers/base/dd.c:561
__device_release_driver drivers/base/dd.c:1273 [inline]
device_release_driver_internal+0x44a/0x610 drivers/base/dd.c:1296
bus_remove_device+0x22f/0x420 drivers/base/bus.c:576
device_del+0x396/0x9f0 drivers/base/core.c:3864
usb_disable_device+0x36c/0x7f0 drivers/usb/core/message.c:1418
usb_disconnect+0x2e1/0x920 drivers/usb/core/hub.c:2304
hub_port_connect drivers/usb/core/hub.c:5361 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5661 [inline]
port_event drivers/usb/core/hub.c:5821 [inline]
hub_event+0x1bed/0x4f40 drivers/usb/core/hub.c:5903
process_one_work+0x9c5/0x1ba0 kernel/workqueue.c:3229
process_scheduled_works kernel/workqueue.c:3310 [inline]
worker_thread+0x6c8/0xf00 kernel/workqueue.c:3391
kthread+0x2c1/0x3a0 kernel/kthread.c:389
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(chaoskey_list_lock);
lock(minor_rwsem);
lock(chaoskey_list_lock);
lock(minor_rwsem);
*** DEADLOCK ***
[Analysis]
The first is AA lock, it because wrong logic, it need a unlock.
The second is AB lock, it needs to rearrange the order of lock usage.
Fixes: 422dc0a4d1 ("USB: chaoskey: fail open after removal")
Reported-by: syzbot+685e14d04fe35692d3bc@syzkaller.appspotmail.com
Reported-by: syzbot+1f8ca5ee82576ec01f12@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=685e14d04fe35692d3bc
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Tested-by: syzbot+685e14d04fe35692d3bc@syzkaller.appspotmail.com
Reported-by: syzbot+5f1ce62e956b7b19610e@syzkaller.appspotmail.com
Tested-by: syzbot+5f1ce62e956b7b19610e@syzkaller.appspotmail.com
Tested-by: syzbot+1f8ca5ee82576ec01f12@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/tencent_84EB865C89862EC22EE94CB3A7C706C59206@qq.com
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 86b20af11e.
This patch leads to passing 0 to simple_read_from_buffer()
as a fifth argument, turning the read method into a nop.
The change is fundamentally flawed, as it breaks the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20241007094004.242122-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I have a ASUS PN51 S mini pc that has two xhci devices. One from AMD,
and other from ASMEDIA. The one from ASMEDIA have problems when resume
from suspend, and keep broken until unplug the power cord. I use this
kernel parameter: xhci-hcd.quirks=128 and then it works ok. I make a
path to reset only the ASMEDIA xhci.
Signed-off-by: Jose Alberto Reguero <jose.alberto.reguero@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240919184202.22249-1-jose.alberto.reguero@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce new kernel config symbol for Microchip usb5744 SMBus programming
support. Since usb5744 i2c initialization routine uses i2c SMBus APIs these
APIs should only be invoked when kernel has I2C support. This new kernel
config describes the dependency on I2C kernel support and fix the below
build issues when USB_ONBOARD_DEV=y and CONFIG_I2C=m.
riscv64-linux-ld: drivers/usb/misc/onboard_usb_dev.o:
undefined reference to `i2c_find_device_by_fwnode'
drivers/usb/misc/onboard_usb_dev.c:408:(.text+0xb24): undefined
reference to `i2c_smbus_write_block_data'
<snip>
Parsing of the i2c-bus bus handle is not put under usb5744 kernel config
check as the intention is to report an error when DT is configured for
usb5744 SMBus support and kernel has USB_ONBOARD_DEV_USB5744 disabled.
Fixes: 6782311d04 ("usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Suggested-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409140539.3Axwv38m-lkp@intel.com/
Acked-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Link: https://lore.kernel.org/r/1727529992-476088-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit addresses an issue where events were being processed when
the controller was in a halted state. To fix this issue by stop
processing the events as the event count was considered stale or
invalid when the controller was halted.
Fixes: fc8bb91bc8 ("usb: dwc3: implement runtime PM")
Cc: stable@kernel.org
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240916231813.206-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dwc3_resume_common() returns an error, runtime pm is left in
suspended and disabled state in dwc3_resume(). Since the device
is suspended, its parent devices (like the power domain or glue
driver) could also be suspended and may have released resources
that dwc requires. Consequently, calling dwc3_suspend_common() in
this situation could result in attempts to access unclocked or
unpowered registers.
To prevent these problems, runtime PM should always be re-enabled,
even after failed resume attempts. This ensures that
dwc3_suspend_common() is skipped in such cases.
Fixes: 68c26fe581 ("usb: dwc3: set pm runtime active before resume common")
Cc: stable@vger.kernel.org
Signed-off-by: Roy Luo <royluo@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240913232145.3507723-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
JieLi tends to use SCSI via USB Mass Storage to implement their own
proprietary commands instead of implementing another USB interface.
Enumerating it as a generic mass storage device will lead to a Hardware
Error sense key get reported.
Ignore this bogus device to prevent appearing a unusable sdX device
file.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241001083407.8336-1-uwu@icenowy.me
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Registering a gadget driver is expected to complete synchronously and
immediately after calling driver_register() this function checks that
the driver has bound so as to return an error.
Set PROBE_FORCE_SYNCHRONOUS to ensure this is the case even when
asynchronous probing is set as the default.
Fixes: fc274c1e99 ("USB: gadget: Add a new bus for gadgets")
Cc: stable@vger.kernel.org
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Link: https://lore.kernel.org/r/20240913102325.2826261-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
chaoskey_open() takes the lock only to increase the
counter of openings. That means that the mutual exclusion
with chaoskey_disconnect() cannot prevent an increase
of the counter and chaoskey_open() returning a success.
If that race is hit, chaoskey_disconnect() will happily
free all resources associated with the device after
it has dropped the lock, as it has read the counter
as zero.
To prevent this race chaoskey_open() has to check
the presence of the device under the lock.
However, the current per device lock cannot be used,
because it is a part of the data structure to be
freed. Hence an additional global mutex is needed.
The issue is as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+422188bce66e76020e55@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=422188bce66e76020e55
Fixes: 66e3e59189 ("usb: Add driver for Altus Metrum ChaosKey device (v2)")
Rule: add
Link: https://lore.kernel.org/stable/20241002132201.552578-1-oneukum%40suse.com
Link: https://lore.kernel.org/r/20241002132201.552578-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IO yurex_write() needs to wait for in order to have a device
ready for writing again can take a long time time.
Consequently the sleep is done in an interruptible state.
Therefore others waiting for yurex_write() itself to finish should
use mutex_lock_interruptible.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Rule: add
Link: https://lore.kernel.org/stable/20240924084415.300557-1-oneukum%40suse.com
Link: https://lore.kernel.org/r/20240924084415.300557-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iowarrior_read() uses the iowarrior dev structure, but does not use any
lock on the structure. This can cause various bugs including data-races,
so it is more appropriate to use a mutex lock to safely protect the
iowarrior dev structure. When using a mutex lock, you should split the
branch to prevent blocking when the O_NONBLOCK flag is set.
In addition, it is unnecessary to check for NULL on the iowarrior dev
structure obtained by reading file->private_data. Therefore, it is
better to remove the check.
Fixes: 946b960d13 ("USB: add driver for iowarrior devices.")
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Link: https://lore.kernel.org/r/20240919103403.3986-1-aha310510@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reorganize kerneldoc parameter names to match the parameter
order in the function header.
Problems identified using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20240930112121.95324-19-Julia.Lawall@inria.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Impove device mode ISO transfer error tolerant by reprime the corresponding
endpoint.
The recovery steps when error occurs:
- Delete the error dTD from dQH and giveback request to user.
- Do reprime if dQH is not empty.
- Do prime when new dTD is queued if dQH is empty
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240926022906.473319-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, ATDTW semaphore is used to safety link new dTD to dQH. But this
code has a bug when the endpoint is already in error before polling ATDTW
or just met error during polling ATDTW. In that cases, ATDTW will never
turn to 1 and the cpu will busy loop there.
When the endpoint met error, ENDPTSTAT will be cleared by HW. Therefore,
ENDPTSTAT should also be considered during this process. In case of
endpoint error, the current dTD should not be pushed to the head of dQH
since some dTDs may be still not executed. Therefore, the link logic is
also improved accordingly.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240926022906.473319-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per USBSTS register description about UEI:
When completion of a USB transaction results in an error condition, this
bit is set by the Host/Device Controller. This bit is set along with the
USBINT bit, if the TD on which the error interrupt occurred also had its
interrupt on complete (IOC) bit set.
UI is set only when IOC set. Add checking UEI to fix miss call
isr_tr_complete_handler() when IOC have not set and transfer error happen.
Acked-by: Peter Chen <peter.chen@kernel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240926022906.473319-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chipidea controller doesn't fully support sglist, such as it can not
transfer data spanned more dTDs to form a bus packet, so it can only work
on very limited cases.
The limitations as below:
1. the end address of the first sg buffer must be 4KB aligned.
2. the start and end address of the middle sg buffer must be 4KB aligned.
3. the start address of the first sg buffer must be 4KB aligned.
However, not all the use cases violate these limitations. To make the
controller compatible with most of the cases, this will try to bounce the
problem sglist entries which can be found by sglist_get_invalid_entry().
Then a bounced line buffer (the size will roundup to page size) will be
allocated to replace the remaining problem sg entries. The data will be
copied between problem sg entries and bounce buffer according to the
transfer direction. The bounce buffer will be freed when the request
completed.
Acked-by: Peter Chen <peter.chen@kernel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240923081203.2851768-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To let the device controller work properly on short packet limitations,
one usb request should only correspond to one dTD. Then every dTD will
set IOC. In theory, each dTD support up to 20KB data transfer if the
offset is 0. Due to we cannot predetermine the offset, this will limit
the usb request length to max 16KB. This should be fine since most of
the user transfer data based on this size policy.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240923081203.2851768-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the imx deivice controller has below limitations:
1. can't generate short packet interrupt if IOC not set in dTD. So if one
request span more than one dTDs and only the last dTD set IOC, the usb
request will pending there if no more data comes.
2. the controller can't accurately deliver data to differtent usb requests
in some cases due to short packet. For example: one usb request span 3
dTDs, then if the controller received a short packet the next packet
will go to 2nd dTD of current request rather than the first dTD of next
request.
3. can't build a bus packet use multiple dTDs. For example: controller
needs to send one packet of 512 bytes use dTD1 (200 bytes) + dTD2
(312 bytes), actually the host side will see 200 bytes short packet.
Based on these limits, add CI_HDRC_HAS_SHORT_PKT_LIMIT flag and use it on
imx platforms.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240923081203.2851768-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/usb to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240924084329.53094-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240920153430.503212-17-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function strcpy() is depreciated and potentially unsafe. It performs
no bounds checking on the destination buffer. This could result in
linear overflows beyond the end of the buffer, leading to all kinds of
misbehaviors. The safe replacement is strscpy() [1].
this fixes checkpatch warning:
WARNING: Prefer strscpy over strcpy
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strcpy [1]
Signed-off-by: Abdul Rahim <abdul.rahim@myyahoo.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20240914231756.503521-1-abdul.rahim@myyahoo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get matching data in one step by switching to use i2c_get_match_data().
As a positive side effect the matching data is qualified as a constant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240926122944.1251923-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the scoped variant of `device_for_each_child_node()` to
automatically handle early exits.
This prevents memory leaks if new error paths are introduced,
as no explicit refcount decrement via `fwnode_handle_put()` is needed.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240925-ucsi_glink-scoped-v2-1-a661585fff35@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed some confusing typos that were currently identified with codespell,
the details are as follows:
-in the code comments:
drivers/usb/dwc3/core.c:1406: feild ==> field
drivers/usb/dwc3/core.h:84: boundries ==> boundaries
drivers/usb/dwc3/ep0.c:148: issueing ==> issuing
drivers/usb/dwc3/host.c:38: temperary ==> temporarily
Also fixed a syntax problem in the comments.
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Link: https://lore.kernel.org/r/20240930022526.7255-1-shenlichuan@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup of
the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART engine
that that chip seems to have. Hopefully it's in a better state now,
but hardware designers still seem to come up with more ways to make
broken UARTS 40+ years after this all should have finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZvUz1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymAhwCcCw/6BX3aKGTyx7ZxeMRc/mjbSLIAoMUv6bGT
6H04ZvcSd63ZotAWeZsn
=PWB8
-----END PGP SIGNATURE-----
Merge tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup
of the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART
engine that that chip seems to have. Hopefully it's in a better
state now, but hardware designers still seem to come up with more
ways to make broken UARTS 40+ years after this all should have
finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems"
* tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: samsung: Fix serial rx on Apple A7-A9
tty: serial: samsung: Fix A7-A11 serial earlycon SError
tty: serial: samsung: Use bit manipulation macros for APPLE_S5L_*
tty: rp2: Fix reset with non forgiving PCIe host bridges
serial: 8250_aspeed_vuart: Enable module autoloading
serial: qcom-geni: fix polled console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix console corruption
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix fifo polling timeout
tty: hvc: convert comma to semicolon
mxser: convert comma to semicolon
serial: 8250_bcm2835aux: Fix clock imbalance in PM resume
serial: sc16is7xx: convert bitmask definitions to use BIT() macro
serial: sc16is7xx: fix copy-paste errors in EFR_SWFLOWx_BIT constants
serial: sc16is7xx: remove SC16IS7XX_MSR_DELTA_MASK
serial: xilinx_uartps: Make cdns_rs485_supported static
...
Here is the large set of USB and Thunderbolt changes for 6.12-rc1.
Nothing "major" in here, except for a new 9p network gadget that has
been worked on for a long time (all of the needed acks are here.) Other
than that, it's the usual set of:
- Thunderbolt / USB4 driver updates and additions for new hardware
- dwc3 driver updates and new features added
- xhci driver updates
- typec driver updates
- USB gadget updates and api additions to make some gadgets more
configurable by userspace
- dwc2 driver updates
- usb phy driver updates
- usbip feature additions
- other minor USB driver updates
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZvU0/g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykGcACfSqouxRg8FRtq+nIKHWXI9lOTnVcAoKd9PAgq
1i7yCNopPEPEW8sjz1GX
=mY+S
-----END PGP SIGNATURE-----
Merge tag 'usb-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the large set of USB and Thunderbolt changes for 6.12-rc1.
Nothing "major" in here, except for a new 9p network gadget that has
been worked on for a long time (all of the needed acks are here)
Other than that, it's the usual set of:
- Thunderbolt / USB4 driver updates and additions for new hardware
- dwc3 driver updates and new features added
- xhci driver updates
- typec driver updates
- USB gadget updates and api additions to make some gadgets more
configurable by userspace
- dwc2 driver updates
- usb phy driver updates
- usbip feature additions
- other minor USB driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (145 commits)
sub: cdns3: Use predefined PCI vendor ID constant
sub: cdns2: Use predefined PCI vendor ID constant
USB: misc: yurex: fix race between read and write
USB: misc: cypress_cy7c63: check for short transfer
USB: appledisplay: close race between probe and completion handler
USB: class: CDC-ACM: fix race between get_serial and set_serial
usb: r8a66597-hcd: make read-only const arrays static
usb: typec: ucsi: Fix busy loop on ASUS VivoBooks
usb: dwc3: rtk: Clean up error code in __get_dwc3_maximum_speed()
usb: storage: ene_ub6250: Fix right shift warnings
usb: roles: Improve the fix for a false positive recursive locking complaint
locking/mutex: Introduce mutex_init_with_key()
locking/mutex: Define mutex_init() once
net/9p/usbg: fix CONFIG_USB_GADGET dependency
usb: xhci: fix loss of data on Cadence xHC
usb: xHCI: add XHCI_RESET_ON_RESUME quirk for Phytium xHCI host
usb: dwc3: imx8mp: disable SS_CON and U3 wakeup for system sleep
usb: dwc3: imx8mp: add 2 software managed quirk properties for host mode
usb: host: xhci-plat: Parse xhci-missing_cas_quirk and apply quirk
usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support
...
Highlights:
- asus-wmi: Add support for vivobook fan profiles
- dell-laptop: Add knobs to change battery charge settings
- lg-laptop: Add operation region support
- intel-uncore-freq: Add support for efficiency latency control
- intel/ifs: Add SBAF test support
- intel/pmc: Ignore all LTRs during suspend
- platform/surface: Support for arm64 based Surface devices
- wmi: Pass event data directly to legacy notify handlers
- x86/platform/geode: switch GPIO buttons and LEDs to software properties
- bunch of small cleanups, fixes, hw-id additions, etc.
The following is an automated git shortlog grouped by driver:
Documentation:
- admin-guide: pm: Add efficiency vs. latency tradeoff to uncore documentation
ISST:
- Simplify isst_misc_reg() and isst_misc_unreg()
MAINTAINERS:
- adjust file entry in INTEL MID PLATFORM
- Add Intel MID section
Merge tag 'hwmon-for-v6.11-rc7' into review-hans:
- Merge tag 'hwmon-for-v6.11-rc7' into review-hans
Merge tag 'platform-drivers-x86-v6.11-3' into review-hans:
- Merge tag 'platform-drivers-x86-v6.11-3' into review-hans
acer-wmi:
- Use backlight power constants
asus-laptop:
- Use backlight power constants
asus-nb-wmi:
- Use backlight power constants
asus-wmi:
- don't fail if platform_profile already registered
- add debug print in more key places
- Use backlight power constants
- add support for vivobook fan profiles
dell-laptop:
- remove duplicate code w/ battery function
- Add knobs to change battery charge settings
dt-bindings:
- platform: Add Surface System Aggregator Module
- serial: Allow embedded-controller as child node
eeepc-laptop:
- Use backlight power constants
eeepc-wmi:
- Use backlight power constants
fujitsu-laptop:
- Use backlight power constants
hid-asus:
- use hid for brightness control on keyboard
ideapad-laptop:
- Make the scope_guard() clear of its scope
- move ACPI helpers from header to source file
- Use backlight power constants
int3472:
- Use str_high_low()
- Use GPIO_LOOKUP() macro
- make common part a separate module
intel-hid:
- Use string_choices API instead of ternary operator
intel/pmc:
- Ignore all LTRs during suspend
- Remove unused param idx from pmc_for_each_mode()
intel_scu_ipc:
- Move intel_scu_ipc.h out of arch/x86/include/asm
intel_scu_wdt:
- Move intel_scu_wdt.h to x86 subfolder
lenovo-ymc:
- Ignore the 0x0 state
lg-laptop:
- Add operation region support
oaktrail:
- Use backlight power constants
panasonic-laptop:
- Add support for programmable buttons
platform/mellanox:
- mlxbf-pmc: fix lockdep warning
platform/olpc:
- Remove redundant null pointer checks in olpc_ec_setup_debugfs()
platform/surface:
- Add OF support
platform/x86/amd:
- pmf: Add quirk for TUF Gaming A14
platform/x86/amd/pmf:
- Update SMU metrics table for 1AH family series
- Relocate CPU ID macros to the PMF header
- Add support for notifying Smart PC Solution updates
platform/x86/intel-uncore-freq:
- Add efficiency latency control to sysfs interface
- Add support for efficiency latency control
- Do not present separate package-die domain
platform/x86/intel/ifs:
- Fix SBAF title underline length
- Add SBAF test support
- Add SBAF test image loading support
- Refactor MSR usage in IFS test code
platform/x86/intel/pmc:
- Show live substate requirements
platform/x86/intel/pmt:
- Use PMT callbacks
platform/x86/intel/vsec:
- Add PMT read callbacks
platform/x86/intel/vsec.h:
- Move to include/linux
samsung-laptop:
- Use backlight power constants
serial-multi-instantiate:
- Don't require both I2C and SPI
thinkpad_acpi:
- Fix uninitialized symbol 's' warning
- Add Thinkpad Edge E531 fan support
touchscreen_dmi:
- add nanote-next quirk
trace:
- platform/x86/intel/ifs: Add SBAF trace support
wmi:
- Call both legacy and WMI driver notify handlers
- Merge get_event_data() with wmi_get_notify_data()
- Remove wmi_get_event_data()
- Pass event data directly to legacy notify handlers
x86-android-tablets:
- Adjust Xiaomi Pad 2 bottom bezel touch buttons LED
- Fix spelling in the comments
x86/platform/geode:
- switch GPIO buttons and LEDs to software properties
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmbq2tYUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9xKYAgAoXZt1MjBDA1mP813i4bj8CYQHWO+
YnugVhEccucxgC6sBGzQeRLBNuG/VaBN6tyJ1pKYMpWV5gSthq1Iop+DZbno2ciM
QAnSSzioHB/dhYBXuKmZatkMsKLjLjtfcexUed9DfwKapqFl3XQMb6cEYasM37hH
197K4yAFF3oqQImlACwQDxN1q3eCG6bdIbEAByZW7yH644IC5zH8/CiFjTCwUx/F
aFIHQlLLzt1kjhD8AbRHhRcsGbzG2ejHsC3yrQddEJSOkInDO8baR0aDyhBTUFPE
lztuekFfaJ1Xcyoc/Zf4pi3ab1Djt+Htck3CHLO/xcl0YYMlM5vcs1QlhQ==
=sAk7
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform drivers updates from Hans de Goede:
- asus-wmi: Add support for vivobook fan profiles
- dell-laptop: Add knobs to change battery charge settings
- lg-laptop: Add operation region support
- intel-uncore-freq: Add support for efficiency latency control
- intel/ifs: Add SBAF test support
- intel/pmc: Ignore all LTRs during suspend
- platform/surface: Support for arm64 based Surface devices
- wmi: Pass event data directly to legacy notify handlers
- x86/platform/geode: switch GPIO buttons and LEDs to software
properties
- bunch of small cleanups, fixes, hw-id additions, etc.
* tag 'platform-drivers-x86-v6.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (65 commits)
MAINTAINERS: adjust file entry in INTEL MID PLATFORM
platform/x86: x86-android-tablets: Adjust Xiaomi Pad 2 bottom bezel touch buttons LED
platform/mellanox: mlxbf-pmc: fix lockdep warning
platform/x86/amd: pmf: Add quirk for TUF Gaming A14
platform/x86: touchscreen_dmi: add nanote-next quirk
platform/x86: asus-wmi: don't fail if platform_profile already registered
platform/x86: asus-wmi: add debug print in more key places
platform/x86: intel_scu_wdt: Move intel_scu_wdt.h to x86 subfolder
platform/x86: intel_scu_ipc: Move intel_scu_ipc.h out of arch/x86/include/asm
MAINTAINERS: Add Intel MID section
platform/x86: panasonic-laptop: Add support for programmable buttons
platform/olpc: Remove redundant null pointer checks in olpc_ec_setup_debugfs()
platform/x86: intel/pmc: Ignore all LTRs during suspend
platform/x86: wmi: Call both legacy and WMI driver notify handlers
platform/x86: wmi: Merge get_event_data() with wmi_get_notify_data()
platform/x86: wmi: Remove wmi_get_event_data()
platform/x86: wmi: Pass event data directly to legacy notify handlers
platform/x86: thinkpad_acpi: Fix uninitialized symbol 's' warning
platform/x86: x86-android-tablets: Fix spelling in the comments
platform/x86: ideapad-laptop: Make the scope_guard() clear of its scope
...
* power-supply core
- introduce power_supply_show_enum_with_available() helper
- change usb_types from an array into a bitmask
- fix early usage of power_supply_property_is_writeable() resulting
in sysfs files not being writable
- fix missing temp1_max_alarm attribute in power-supply's hwmon devices
* drivers
- max1720x: expose nvmem device
- brcmstb: cleanup driver to use latest APIs
- max77693: expose input and charging current limit
- max17042_battery: fix state of charge reading for devices without
current sensing
- axp20x_battery: add AXP717 support
- axp20x_battery: fix min/max voltage properties
- axp20x_usb_power: add AXP717 support
- axp20x_usb_power: add DT based input current limit
* Documentation updates
* misc. minor cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=UKRL
-----END PGP SIGNATURE-----
Merge tag 'for-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- introduce power_supply_show_enum_with_available() helper
- change usb_types from an array into a bitmask
- fix early usage of power_supply_property_is_writeable() resulting
in sysfs files not being writable
- fix missing temp1_max_alarm attribute in power-supply's hwmon
devices
Drivers:
- max1720x: expose nvmem device
- brcmstb: cleanup driver to use latest APIs
- max77693: expose input and charging current limit
- max17042_battery: fix state of charge reading for devices without
current sensing
- axp20x_battery: add AXP717 support
- axp20x_battery: fix min/max voltage properties
- axp20x_usb_power: add AXP717 support
- axp20x_usb_power: add DT based input current limit
Documentation updates
Misc minor cleanups and fixes"
* tag 'for-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (38 commits)
power: supply: hwmon: Fix missing temp1_max_alarm attribute
power: supply: Drop use_cnt check from power_supply_property_is_writeable()
power: supply: ab8500: Constify struct kobj_type
power: supply: max1720x: fix a double free on error in probe()
power: supply: axp20x_battery: add support for AXP717
power: supply: axp20x_usb_power: Add support for AXP717
dt-bindings: power: supply: axp20x: Add AXP717 compatible
dt-bindings: power: supply: axp20x: Add AXP717 compatible
power: supply: axp20x_usb_power: Fix spelling mistake "reqested" -> "requested"
power: supply: Change usb_types from an array into a bitmask
power: supply: sysfs: Move power_supply_show_enum_with_available() up
power: supply: sysfs: Add power_supply_show_enum_with_available() helper
power: supply: rt9467-charger: Remove "usb_type" property write support
power: supply: ucs1002: Adjust ucs1002_set_usb_type() to accept string values
power: supply: "usb_type" property may be written to
power: supply: max1720x: add read support for nvmem
mfd: axp20x: Add ADC, BAT, and USB cells for AXP717
power: supply: core: constify psy_tzd_ops
power: reset: brcmstb: Do not go into infinite loop if reset fails
power: reset: brcmstb: Use devm_register_sys_off_handler()
...
The PCI vendor ID for Cadence is defined in pci_ids.h. Use it.
While at it, move to PCI_DEVICE() macro and usual pattern for
PCI class and device IDs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240913131710.3630560-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PCI vendor ID for Cadence is defined in pci_ids.h. Use it.
While at it, move to PCI_DEVICE() macro and usual pattern for
PCI class and device IDs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240913132125.3630860-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a small window during probing when IO is running
but the backlight is not registered. Processing events
during that time will crash. The completion handler
needs to check for a backlight before scheduling work.
The bug is as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240912123317.1026049-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TIOCGSERIAL is an ioctl. Thus it must be atomic. It returns
two values. Racing with set_serial it can return an inconsistent
result. The mutex must be taken.
In terms of logic the bug is as old as the driver. In terms of
code it goes back to the conversion to the get_serial and
set_serial methods.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Fixes: 99f75a1fcd ("cdc-acm: switch to ->[sg]et_serial()")
Link: https://lore.kernel.org/r/20240912141916.1044393-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't populate the read-only const arrays fifoaddr, fifosel and fifoctr
on the stack at run time, instead make them static.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240912132345.589397-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the busy indicator is set, all other fields in CCI should be
clear according to the spec. However, some UCSI implementations do
not follow this rule and report bogus data in CCI along with the
busy indicator. Ignore the contents of CCI if the busy indicator is
set.
If a command timeout is hit it is possible that the EVENT_PENDING
bit is cleared while connector work is still scheduled which can
cause the EVENT_PENDING bit to go out of sync with scheduled connector
work. Check and set the EVENT_PENDING bit on entry to
ucsi_handle_connector_change() to fix this.
Finally, check UCSI_CCI_BUSY before the return code of ->sync_control.
This ensures that the command is cancelled even if ->sync_control
returns an error (most likely -ETIMEDOUT).
Reported-by: Anurag Bijea <icaliberdev@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219108
Bisected-by: Christian Heusel <christian@heusel.eu>
Tested-by: Anurag Bijea <icaliberdev@gmail.com>
Fixes: de52aca4d9 ("usb: typec: ucsi: Never send a lone connector change ack")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240912074132.722855-1-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The __get_dwc3_maximum_speed() function returns an enum type which, in
this context here, is basically unsigned int. On error cases, it's
supposed to return USB_SPEED_UNKNOWN, but it was accidentally changed to
return negative error codes in commit f93e96c544 ("usb: dwc3: rtk: use
scoped device node handling to simplify error paths").
There is only one caller and because of the way that the types work out,
returning negative error codes is not a problem. They will be treated
as greater than USB_SPEED_HIGH and ignored as invalid. So this patch
does not affect run time behavior, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/865e56dc-37cc-47b1-8d35-9047ecb1984a@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change bl_len from u16 to u32 to accommodate the necessary bit shifts.
Fix the following smatch warnings:
drivers/usb/storage/ene_ub6250.c:1509 ms_scsi_read_capacity() warn:
right shifting more than type allows 16 vs 24
drivers/usb/storage/ene_ub6250.c:1510 ms_scsi_read_capacity() warn:
right shifting more than type allows 16 vs 16
Signed-off-by: Abhishek Tamboli <abhishektamboli9@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240912145247.15544-1-abhishektamboli9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve commit fc88bb1161 ("usb: roles: add lockdep class key to struct
usb_role_switch") as follows:
* Move the lock class key declaration just above the mutex declaration such
that the declaration order of these objects matches their initialization
order.
* Destroy the mutex and lock class key just before these objects are
freed. This makes it easier to verify that the destruction calls happen
after the last use of these objects.
* Instead of switching the mutex key to the dynamic lock class key after
initialization of the mutex has completed, initialize the mutex with the
dynamic lock class key.
Cc: Amit Sunil Dhamne <amitsd@google.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240912223956.3554086-4-bvanassche@acm.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams should flush their TRB cache, re-read TRBs, and start executing
TRBs from the beginning of the new dequeue pointer after a 'Set TR Dequeue
Pointer' command.
Cadence controllers may fail to start from the beginning of the dequeue
TRB as it doesn't clear the Opaque 'RsvdO' field of the stream context
during 'Set TR Dequeue' command. This stream context area is where xHC
stores information about the last partially executed TD when a stream
is stopped. xHC uses this information to resume the transfer where it left
mid TD, when the stream is restarted.
Patch fixes this by clearing out all RsvdO fields before initializing new
Stream transfer using a 'Set TR Dequeue Pointer' command.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: stable@vger.kernel.org
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB95386A40146E3EC64086F409DD9D2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SS_CON and U3 wakeup need 'ref_clk' on. iMX8MP turn off it while system
sleep, So disable these wakeup source and only enable DP/DM wakeup source
for host mode.
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240906-dwc-mp-v5-3-ea8ec6774e7b@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 2 software manage quirk properties (xhci-missing-cas-quirk and
xhci-skip-phy-init-quirk) for xhci host.
dwc3 driver have PHY management to cover both device and host mode, so add
xhci-skip-phy-init-quirk to skip PHY management from HCD core.
Cold Attach Status (CAS) bit can't be set at i.MX8MP after resume from
suspend state. So set xhci-missing-cas-quirk.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240906-dwc-mp-v5-2-ea8ec6774e7b@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parse software managed property 'xhci-skip-phy-init-quirk' and
'xhci-skip-phy-init-quirk' to apply related quirk. It allows usb glue layer
driver apply these quirk.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240906-dwc-mp-v5-1-ea8ec6774e7b@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb5744 supports SMBus Configuration and it may be configured via the
SMBus slave interface during the hub start-up configuration stage.
To program it driver uses i2c-bus phandle (added in commit '02be19e914b8
dt-bindings: usb: Add support for Microchip usb5744 hub controller') to
get i2c client device and then based on usb5744 compatible check calls
usb5744 i2c default initialization sequence.
Apart from the USB command attach, prevent the hub from suspend.
when the USB Attach with SMBus (0xAA56) command is issued to the hub,
the hub is getting enumerated and then it puts in a suspend mode.
This causes the hub to NAK any SMBus access made by the SMBus Master
during this period and not able to see the hub's slave address while
running the "i2c probe" command.
Prevent the MCU from putting the HUB in suspend mode through register
write. The BYPASS_UDC_SUSPEND bit (Bit 3) of the RuntimeFlags2
register at address 0x411D controls this aspect of the hub. The
BYPASS_UDC_SUSPEND bit in register 0x411Dh must be set to ensure that the
MCU is always enabled and ready to respond to SMBus runtime commands.
This register needs to be written before the USB attach command is issued.
The byte sequence is as follows:
Slave addr: 0x2d 00 00 05 00 01 41 1D 08
Slave addr: 0x2d 99 37 00
Slave addr: 0x2d AA 56 00
Also since usb5744 i2c initialization routine uses i2c SMBus APIs invoke
these APIs only when i2c driver is enabled in the kernel configuration.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1725732196-70975-3-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce dedicated field 'power_on_delay_us' in onboard platform data
and update its delay for USB5744 configuration. Hub itself requires some
delay after reset to get to state where configuration data is going to
be accepted. Without delay upcoming support for configuration via SMBUS
is reporting a failure on the first SMBus write.
i2c 2-002d: error -ENXIO: BYPASS_UDC_SUSPEND bit configuration failed
Similar delay is likely also required for default configuration but
because there is enough time (code execution) between reset and usage
of the hub any issue is not visible but it doesn't mean delay shouldn't
be reflected.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Suggested-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1725732196-70975-2-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc2_handle_usb_suspend_intr() function disables gadget clocks in USB
peripheral mode when no other power-down mode is available (introduced by
commit 0112b7ce68 ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")).
However, the dwc2_drd_role_sw_set() USB role update handler attempts to
read DWC2 registers if the USB role has changed while the USB is in suspend
mode (when the clocks are gated). This causes the system to hang.
Release the gadget clocks before handling the USB role update.
Fixes: 0112b7ce68 ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")
Cc: stable@vger.kernel.org
Signed-off-by: Tomas Marek <tomas.marek@elrest.cz>
Link: https://lore.kernel.org/r/20240906055025.25057-1-tomas.marek@elrest.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix changes incorrect usb_request->status returned during disabling
endpoints. Before fix the status returned during dequeuing requests
while disabling endpoint was ECONNRESET.
Patch change it to ESHUTDOWN.
Patch fixes issue detected during testing UVC gadget.
During stopping streaming the class starts dequeuing usb requests and
controller driver returns the -ECONNRESET status. After completion
requests the class or application "uvc-gadget" try to queue this
request again. Changing this status to ESHUTDOWN cause that UVC assumes
that endpoint is disabled, or device is disconnected and stops
re-queuing usb requests.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: stable@vger.kernel.org
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB9538E8CA7A2096AAF6A3718FDD9E2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPCI USB PHY - PTN5110 could be used with SOCs that only support
the edge-triggered GPIO interrupts such as TI's K3 device AM69.
Move the interrupt configuration to the firmware which would
allow to accommodate edge triggered interrupts for such SOCs.
In order to support the edge interrupts, register irq line in advance
and keep track of occurrence during port registering.
When the edge interrupts are used, it is observed that some of the
interrupts are missed when tcpci_irq() is serving the current
interrupt. Therefore, check the status register at the end of
tcpci_irq() and re-run the function if the status is not clear
i.e. pending interrupt.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240905065328.7116-1-parth105105@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The combination of dev_err() and the returned error code could be
replaced by dev_err_probe() in driver's probe function. Let's,
converting to dev_err_probe() to make code more simple.
Signed-off-by: Lin Ruifeng <linruifeng4@huawei.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20240907081351.19879-1-linruifeng4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a new pl2303 device id.
This one has been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZuEzcQAKCRALxc3C7H1l
CGeZAQDn3AvDVGqJJ4kBZC1ldLo4aOz6z5+njmoL2cZyQ3d5iwD9F0e10fd2FA6a
fxm3gt5cJEtbs+kt8V6LhIXbTqtMJA0=
=CgUW
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.12-rc1-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial device id for 6.12-rc1
Here's a new pl2303 device id.
This one has been in linux-next with no reported issues.
* tag 'usb-serial-6.12-rc1-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: pl2303: add device id for Macrosilicon MS3020
Here are the USB-serial updates for 6.12-rc1, including:
- fix kobil_sct initial terminal settings
- set driver owner when registering drivers
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZuEywAAKCRALxc3C7H1l
CFAWAP4muwo7gSV//umprCKbXlFGnsfS7rpDuwusRNTZFjGTPAEAs/n0htTNoFo2
RKKnRcZBk7O6Do6eByIQGuEhCYZjgAw=
=iXi0
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.12-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 6.12-rc1
Here are the USB-serial updates for 6.12-rc1, including:
- fix kobil_sct initial terminal settings
- set driver owner when registering drivers
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.12-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: kobil_sct: restore initial terminal settings
USB: serial: drop driver owner initialization
USB: serial: set driver owner when registering drivers
This is a platform/x86 library that is mostly being used by other
drivers not directly under arch/x86 anyway (with the exception of the
Intel MID setup code) so it makes sense that it lives under the
platform_data/x86/ directory instead.
No functional changes intended.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240909124952.1152017-3-andriy.shevchenko@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We need the USB fixes in here as well, and this also resolves the merge
conflict in:
drivers/usb/typec/ucsi/ucsi.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the device id for the Macrosilicon MS3020 which is a
PL2303HXN based device.
Signed-off-by: Junhao Xie <bigfoot@classfun.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Allow creators of seconday interrupters to specify the interrupt
moderation interval value in nanoseconds when creating the interrupter.
If not sure what value to use then use the xhci driver default
xhci->imod_interval
Suggested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI xHC host should be stopped and xhci driver memory freed before putting
host to PCI D3 state during PCI remove callback.
Hosts with XHCI_SPURIOUS_WAKEUP quirk did this the wrong way around
and set the host to D3 before calling usb_hcd_pci_remove(dev), which will
access the host to stop it, and then free xhci.
Fixes: f1f6d9a8b5 ("xhci: don't dereference a xhci member after removing xhci")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce an initial check for an empty list prior to entering the while
loop. Which enables, the implementation of distinct warnings to
differentiate between scenarios where the list is initially empty and
when it has been emptied during processing skipped isoc TDs.
These adjustments not only simplifies the large while loop, but also
facilitates future enhancements to the handle_tx_event() function.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HCD does not allocate or request interrupt for the xhci driver, but HCD
does free and sync xhci interrupts in some cases. Add comment detailing
in which cases HCD will free/sync xhci interrupts.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'sbrn' is used to store the Serial Bus Release Number, which is
then only used for a debug message. Thus, 'sbrn' can be a local variable
and assigned after the primary HCD check. The SBRN debug message is only
printed when a primary HCD is setup.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Completion codes 'COMP_SUCCESS' and 'COMP_SHORT_PACKET' are the most
frequently encountered completion codes. Typically, these codes do not
trigger a default debug message but rather a warning that indicates a
potential issue. This behavior is consistent across all transfer types
with the exception of Bulk transfers. To reduce unnecessary log clutter,
remove the Bulk 'COMP_SHORT_PACKET' debug message.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The removed debug messages trigger each time an isoc frame is handled.
In case of an error, a dedicated debug message exists.
For example, a 60fps USB camera will trigger the debug message every 0.6s.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we move the requests from the read_queue to the end of the
read_pool list, avoiding looping and using the same one request all
the time.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't flush all pending DbC data requests when an endpoint halts.
An endpoint may halt and xHC DbC triggers a STALL error event if there's
an issue with a bulk data transfer. The transfer should restart once xHC
DbC receives a ClearFeature(ENDPOINT_HALT) request from the host.
Once xHC DbC restarts it will start from the TRB pointed to by dequeue
field in the endpoint context, which might be the same TRB we got the
STALL event for. Turn the TRB to a no-op in this case to make sure xHC
DbC doesn't reuse and tries to retransmit this same TRB after we already
handled it, and gave its corresponding data request back.
Other STALL events might be completely bogus.
Lukasz Bartosik discovered that xHC DbC might issue spurious STALL events
if hosts sends a ClearFeature(ENDPOINT_HALT) request to non-halted
endpoints even without any active bulk transfers.
Assume STALL event is spurious if it reports 0 bytes transferred, and
the endpoint stopped on the STALLED TRB.
Don't give back the data request corresponding to the TRB in this case.
The halted status is per endpoint. Track it with a per endpoint flag
instead of the driver invented DbC wide DS_STALLED state.
DbC remains in DbC-Configured state even if endpoints halt. There is no
Stalled state in the DbC Port state Machine (xhci section 7.6.6)
Reported-by: Łukasz Bartosik <ukaszb@chromium.org>
Closes: https://lore.kernel.org/linux-usb/20240725074857.623299-1-ukaszb@chromium.org/
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bit_types array just hold a list of valid enum power_supply_usb_type
values which map to 0 - 9. This can easily be represented as a bitmap.
This reduces the size of struct power_supply_desc and further reduces
the data section size by drivers no longer needing to store the array.
This also unifies how usb_types are handled with charge_behaviours,
which allows power_supply_show_usb_type() to be removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240831142039.28830-7-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Cable PD Revision field in GET_CABLE_PROPERTY was
introduced in UCSI v2.1, so adding check for that.
The cable properties are also not used anywhere after the
cable is registered, so removing the cable_prop member
from struct ucsi_connector while at it.
Fixes: 38ca416597 ("usb: typec: ucsi: Register cables based on GET_CABLE_PROPERTY")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240903130945.3395291-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Partner PD Revision field in GET_CONNECTOR_CAPABILITY
data structure was introduced in UCSI v2.1. In
ucsi_check_connector_capability() the version was assumed to
be 2.0, and in ucsi_register_partner() the field is accessed
completely unconditionally.
Fixing the version in ucsi_check_connector_capability(), and
replacing the unconditional pd_revision assignment with a
direct call to ucsi_check_connector_capability() in
ucsi_register_port(). After this the revision is also
checked only if there is a PD contract.
Fixes: b9fccfdb4e ("usb: typec: ucsi: Get PD revision for partner")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240830111645.2134301-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fix addresses STAR 9001285599, which only affects DWC_usb3 version
3.20a. The timer value for PM_LC_TIMER in DWC_usb3 3.20a for the Link
ECN changes is incorrect. If the PM TIMER ECN is enabled via GUCTL2[19],
the link compliance test (TD7.21) may fail. If the ECN is not enabled
(GUCTL2[19] = 0), the controller will use the old timer value (5us),
which is still acceptable for the link compliance test. Therefore, clear
GUCTL2[19] to pass the USB link compliance test: TD 7.21.
Cc: stable@vger.kernel.org
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240829094502.26502-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When operating in High-Speed, it is observed that DSTS[USBLNKST] doesn't
update link state immediately after receiving the wakeup interrupt. Since
wakeup event handler calls the resume callbacks, there is a chance that
function drivers can perform an ep queue, which in turn tries to perform
remote wakeup from send_gadget_ep_cmd(STARTXFER). This happens because
DSTS[[21:18] wasn't updated to U0 yet, it's observed that the latency of
DSTS can be in order of milli-seconds. Hence avoid calling gadget_wakeup
during startxfer to prevent unnecessarily issuing remote wakeup to host.
Fixes: c36d8e947a ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: stable@vger.kernel.org
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240828064302.3796315-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We move the func_utils.h header to include/linux/usb to be
able to compile function drivers outside of the
drivers/usb/gadget/function directory.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240116-ml-topic-u9p-v12-1-9a27de5160e0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Describe the power management relationship between a tunneled USB3 device
and the tunnel providing USB4 host with a device link as the relationship
between them is not evident from normal device hierarchy.
Tunneling capable ports have an ACPI _DSD object pointing to the USB4
Host Interface that is used to establish USB3 3.x tunnels
Set the link directly between tunneled USB3 devices and USB4 Host
Interface to ensure that the USB4 host can runtime suspend if no tunneled
USB 3.x devices exist.
Current Thunderbolt code sets a link between USB4 Host Interface and USB3
xHCI host which prevents USB4 Host Interface from runtime suspending even
if the USB3 host is only serving native USB devices.
See commit b2be2b05cf ("thunderbolt: Create device links from ACPI
description") for details.
As the device link is only set for USB3 devices that are already tunneled
we know that USB4 Host Interface exists and is bound to its driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240830152630.3943215-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 'tunnel_mode' enum to usb device structure to describe if a USB3
link is tunneled over USB4, or connected directly using native USB2/USB3
protocols.
Tunneled devices depend on USB4 NHI host to maintain the tunnel.
Knowledge about tunneled devices is important to ensure correct
suspend and resume order between USB4 hosts and tunneled devices.
i.e. make sure tunnel is up before the USB device using it resumes.
USB hosts such as xHCI may have vendor specific ways to detect tunneled
connections. This 'tunnel_mode' parameter can be set by USB3 host driver
during hcd->driver->update_device(hcd, udev) callback.
tunnel_mode can be set to:
USB_LINK_UNKNOWN = 0
USB_LINK_NATIVE
USB_LINK_TUNNELED
USB_LINK_UNKNOWN is used in case host is not capable of detecting
tunneled links.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240830152630.3943215-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Knowledge about tunneled devices is useful in order to correctly describe
the relationship between tunneled USB3 device and USB4 Host Interface,
ensuring proper suspend and resume order, and to be able to power down
Thunderbolt if there is no need for tunneling.
Intel hosts share if a USB3 connection is native or tunneled via vendor
specific "SPR eSS PORT" registers.
These vendor registers are available if host supports a vendor specific
SPR shadow extended capability with ID 206. Registers are per USB3 port
and 0x20 apart.
Knowing the tunneling status of the device connected to roothub is enough
as all its children will have the same status.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240830152630.3943215-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace kthread_create/wake_up_process() with kthread_run()
to simplify the code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://lore.kernel.org/r/20240903014249.3098082-1-lihongbo22@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bInterfaceProtocol is hardcoded to USB_CDC_ACM_PROTO_AT_V25TER. This
will lead to problems with ModemManger which will gladly try to probe
that port as a modem if the gadget also has a network function.
ModemManager will try to send AT commands to the ACM port. Make the
bInterfaceProtocol configurable. For this, track the number of instances
and only allow write to the property if there are no intances (yet).
This will also set bFunctionProtocol to the same value, see commit
5c8db070b4 ("USB: Change acm_iad_descriptor bFunctionProtocol to
USB_CDC_ACM_PROTO_AT_V25TER") for more details.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20240825180446.3757073-1-mwalle@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_clk_get() and clk_prepare_enable() can be replaced by helper
function devm_clk_get_enabled(). Let's use devm_clk_get_enabled() to
simplify code and avoid calling clk_disable_unprepare().
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240902123020.29267-3-zhangzekun11@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The issue is that before entering the crash kernel, the DWC USB controller
did not perform operations such as resetting the interrupt mask bits.
After entering the crash kernel,before the USB interrupt handler
registration was completed while loading the DWC USB driver,an GINTSTS_SOF
interrupt was received.This triggered the misroute_irq process within the
GIC handling framework,ultimately leading to the misrouting of the
interrupt,causing it to be handled by the wrong interrupt handler
and resulting in the issue.
Summary:In a scenario where the kernel triggers a panic and enters
the crash kernel,it is necessary to ensure that the interrupt mask
bit is not enabled before the interrupt registration is complete.
If an interrupt reaches the CPU at this moment,it will certainly
not be handled correctly,especially in cases where this interrupt
is reported frequently.
Please refer to the Crashkernel dmesg information as follows
(the message on line 3 was added before devm_request_irq is
called by the dwc2_driver_probe function):
[ 5.866837][ T1] dwc2 JMIC0010:01: supply vusb_d not found, using dummy regulator
[ 5.874588][ T1] dwc2 JMIC0010:01: supply vusb_a not found, using dummy regulator
[ 5.882335][ T1] dwc2 JMIC0010:01: before devm_request_irq irq: [71], gintmsk[0xf300080e], gintsts[0x04200009]
[ 5.892686][ C0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.0-jmnd1.2_RC #18
[ 5.900327][ C0] Hardware name: CMSS HyperCard4-25G/HyperCard4-25G, BIOS 1.6.4 Jul 8 2024
[ 5.908836][ C0] Call trace:
[ 5.911965][ C0] dump_backtrace+0x0/0x1f0
[ 5.916308][ C0] show_stack+0x20/0x30
[ 5.920304][ C0] dump_stack+0xd8/0x140
[ 5.924387][ C0] pcie_xxx_handler+0x3c/0x1d8
[ 5.930121][ C0] __handle_irq_event_percpu+0x64/0x1e0
[ 5.935506][ C0] handle_irq_event+0x80/0x1d0
[ 5.940109][ C0] try_one_irq+0x138/0x174
[ 5.944365][ C0] misrouted_irq+0x134/0x140
[ 5.948795][ C0] note_interrupt+0x1d0/0x30c
[ 5.953311][ C0] handle_irq_event+0x13c/0x1d0
[ 5.958001][ C0] handle_fasteoi_irq+0xd4/0x260
[ 5.962779][ C0] __handle_domain_irq+0x88/0xf0
[ 5.967555][ C0] gic_handle_irq+0x9c/0x2f0
[ 5.971985][ C0] el1_irq+0xb8/0x140
[ 5.975807][ C0] __setup_irq+0x3dc/0x7cc
[ 5.980064][ C0] request_threaded_irq+0xf4/0x1b4
[ 5.985015][ C0] devm_request_threaded_irq+0x80/0x100
[ 5.990400][ C0] dwc2_driver_probe+0x1b8/0x6b0
[ 5.995178][ C0] platform_drv_probe+0x5c/0xb0
[ 5.999868][ C0] really_probe+0xf8/0x51c
[ 6.004125][ C0] driver_probe_device+0xfc/0x170
[ 6.008989][ C0] device_driver_attach+0xc8/0xd0
[ 6.013853][ C0] __driver_attach+0xe8/0x1b0
[ 6.018369][ C0] bus_for_each_dev+0x7c/0xdc
[ 6.022886][ C0] driver_attach+0x2c/0x3c
[ 6.027143][ C0] bus_add_driver+0xdc/0x240
[ 6.031573][ C0] driver_register+0x80/0x13c
[ 6.036090][ C0] __platform_driver_register+0x50/0x5c
[ 6.041476][ C0] dwc2_platform_driver_init+0x24/0x30
[ 6.046774][ C0] do_one_initcall+0x50/0x25c
[ 6.051291][ C0] do_initcall_level+0xe4/0xfc
[ 6.055894][ C0] do_initcalls+0x80/0xa4
[ 6.060064][ C0] kernel_init_freeable+0x198/0x240
[ 6.065102][ C0] kernel_init+0x1c/0x12c
Signed-off-by: Shawn Shao <shawn.shao@jaguarmicro.com>
Link: https://lore.kernel.org/r/20240830031709.134-1-shawn.shao@jaguarmicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_ioremap_resource() wrapper instead of two calls, which
together with returning directly instead of useless goto, allows to
nicely simplify the probe() function.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-10-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Obtain the device node reference with scoped/cleanup.h to reduce error
handling and make the code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-9-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_ioremap_resource() wrapper instead of two calls. This
allows also dropping local 'res' variable.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-8-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Obtain the device node reference with scoped/cleanup.h to reduce error
handling and make the code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-7-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
