Currently, the transfer polling interval is set to 1ms, which is the
frame rate of full-speed and low-speed USB. The USB 2.0 specification
introduces microframes (125 microseconds) to improve the timing
precision of data transfers.
Reducing the transfer interval to 1 microframe increases data throughput
for high-speed and super-speed USB communication
Signed-off-by: Marcello Sylvester Bauer <marcello.bauer@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/6295dbb84ca76884551df9eb157cce569377a22c.1712843963.git.sylv@sylv.io
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dummy_hcd transfer scheduler assumes that the internal kernel timer
frequency is set to 1000Hz to give a polling interval of 1ms. Reducing
the timer frequency will result in an anti-proportional reduction in
transfer performance. Switch to a hrtimer to decouple this association.
Signed-off-by: Marcello Sylvester Bauer <marcello.bauer@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/57a1c2180ff74661600e010c234d1dbaba1d0d46.1712843963.git.sylv@sylv.io
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().
Note that the upper limit of ida_simple_get() is exclusive, but the one of
ida_alloc_max() is inclusive. So a -1 has been added when needed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/7cd361e2b377a5373968fa7deee4169229992a1e.1713107386.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fsl_ep_queue() is only called by usb_ep_queue() (as ep->ops->queue()).
So _ep isn't NULL.
As ep->ops->queue = fsl_ep_queue, the ep was initialized by
struct_ep_setup() and so ep->udc isn't NULL either.
Drop the check for _ep being NULL and assign udc earlier to prevent
following an uninitialized pointer in the two dev_vdbg()s in lines 878
and 882. This fixes a compiler warning when using clang and
CONFIG_USB_GADGET_VERBOSE=y.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404050227.TTvcCPBu-lkp@intel.com/
Fixes: 6025f20f16 ("usb: gadget: fsl-udc: Replace custom log wrappers by dev_{err,warn,dbg,vdbg}")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240405055812.694123-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver_desc variable is only used in some configurations:
drivers/usb/gadget/udc/omap_udc.c:113:19: error: unused variable 'driver_desc' [-Werror,-Wunused-const-variable]
Since there is only ever one user of it, just open-code the string in place
and remove the global variable and the macro behind it. This also helps
grep for the MODULE_DESCRIPTION string.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240403080702.3509288-26-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ncm function is working and then stop usb0 interface for link down,
eth_stop() is called. At this piont, accidentally if usb transport error
should happen in usb_ep_enable(), 'in_ep' and/or 'out_ep' may not be enabled.
After that, ncm_disable() is called to disable for ncm unbind
but gether_disconnect() is never called since 'in_ep' is not enabled.
As the result, ncm object is released in ncm unbind
but 'dev->port_usb' associated to 'ncm->port' is not NULL.
And when ncm bind again to recover netdev, ncm object is reallocated
but usb0 interface is already associated to previous released ncm object.
Therefore, once usb0 interface is up and eth_start_xmit() is called,
released ncm object is dereferrenced and it might cause use-after-free memory.
[function unlink via configfs]
usb0: eth_stop dev->port_usb=ffffff9b179c3200
--> error happens in usb_ep_enable().
NCM: ncm_disable: ncm=ffffff9b179c3200
--> no gether_disconnect() since ncm->port.in_ep->enabled is false.
NCM: ncm_unbind: ncm unbind ncm=ffffff9b179c3200
NCM: ncm_free: ncm free ncm=ffffff9b179c3200 <-- released ncm
[function link via configfs]
NCM: ncm_alloc: ncm alloc ncm=ffffff9ac4f8a000
NCM: ncm_bind: ncm bind ncm=ffffff9ac4f8a000
NCM: ncm_set_alt: ncm=ffffff9ac4f8a000 alt=0
usb0: eth_open dev->port_usb=ffffff9b179c3200 <-- previous released ncm
usb0: eth_start dev->port_usb=ffffff9b179c3200 <--
eth_start_xmit()
--> dev->wrap()
Unable to handle kernel paging request at virtual address dead00000000014f
This patch addresses the issue by checking if 'ncm->netdev' is not NULL at
ncm_disable() to call gether_disconnect() to deassociate 'dev->port_usb'.
It's more reasonable to check 'ncm->netdev' to call gether_connect/disconnect
rather than check 'ncm->port.in_ep->enabled' since it might not be enabled
but the gether connection might be established.
Signed-off-by: Norihiko Hama <Norihiko.Hama@alpsalpine.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240327023550.51214-1-Norihiko.Hama@alpsalpine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of bailing when fences have already been installed on the
DMABUF, wait for them (with a timeout) when doing a blocking operation.
This fixes the issue where userspace would submit a DMABUF with fences
already installed, with the (correct) expectation that it would just
work.
Fixes: 7b07a2a7ca ("usb: gadget: functionfs: Add DMABUF import interface")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20240402110951.16376-3-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A "read" fence was installed when the DMABUF was to be written to,
and a "write" fence was installed when the DMABUF was to be read from.
Besides, dma_resv_usage_rw() should only be used when waiting for
fences.
Fixes: 7b07a2a7ca ("usb: gadget: functionfs: Add DMABUF import interface")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20240402110951.16376-2-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible trigger below warning message from mass storage function,
WARNING: CPU: 6 PID: 3839 at drivers/usb/gadget/udc/core.c:294 usb_ep_queue+0x7c/0x104
pc : usb_ep_queue+0x7c/0x104
lr : fsg_main_thread+0x494/0x1b3c
Root cause is mass storage function try to queue request from main thread,
but other thread may already disable ep when function disable.
As there is no function failure in the driver, in order to avoid effort
to fix warning, change WARN_ON_ONCE() in usb_ep_queue() to pr_debug().
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240315020144.2715575-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The size given to strscpy() is not consistent with the destination buffer
that is used. The size is related to 'driver' and the buffer is
'mixername'.
sizeof(card->mixername) is 80 and sizeof(card->driver) is 16, so in
theory this could lead to unneeded string truncation.
In practice, this is not the case because g_audio_setup() has only 2
callers. 'card_name' is either "UAC1_Gadget" or "UAC2_Gadget".
Anyway, using the correct size is cleaner and more future proof.
In order to be less verbose, use the new 2-argument version of strscpy()
which computes auto-magically the size of the destination.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/bf8a9353319566624f653531b80e5caf3d346ba1.1711176700.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
udc device and gadget device are tightly coupled, yet there's no good
way to corelate the two. Add a sysfs link in udc that points to the
corresponding gadget device.
An example use case: userspace configures a f_midi configfs driver and
bind the udc device, then it tries to locate the corresponding midi
device, which is a child device of the gadget device. The gadget device
that's associated to the udc device has to be identified in order to
index the midi device. Having a sysfs link would make things much
easier.
Signed-off-by: Roy Luo <royluo@google.com>
Link: https://lore.kernel.org/r/20240307030922.3573161-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Apple CarLife iAP gadget has a descriptor in userspace with two
alternate settings. The host sends the set_alt request to configure
alt_setting 0 or 1, and this is verified by the subsequent get_alt
request.
This patch implements and sets the get_alt callback. Without the
get_alt callback, composite.c abruptly concludes the
USB_REQ_GET/SET_INTERFACE request, assuming only one alt setting
for the endpoint.
unlike the uvc and ncm, f_fs gadget is fully implemented in userspace,
and driver just reset the eps and generate the event. so no additional
adaptaion associated with this change is not required in set_alt callback
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Link: https://lore.kernel.org/r/20240301124708.120394-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting the guid via configfs it is possible to test if
its value is one of the kernel supported ones by calling
uvc_format_by_guid on it. If the result is NULL, we know the
guid is unsupported and can be ignored.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240221-uvc-gadget-configfs-guid-v1-1-f0678ca62ebb@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting uncompressed formats, the values of bytesperline and
sizeimage can already be determined by using the v4l2_fill_pixfmt helper
function. We change the try_fmt function to use the helper instead.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240221-uvc-gadget-uncompressed-v1-1-f55e97287cae@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt changes for 6.9-rc1. Lots of
tiny changes and forward progress to support new hardware and better
support for existing devices. Included in here are:
- Thunderbolt (i.e. USB4) updates for newer hardware and uses as more
people start to use the hardware
- default USB authentication mode Kconfig and documentation update to
make it more obvious what is going on
- USB typec updates and enhancements
- usual dwc3 driver updates
- usual xhci driver updates
- function USB (i.e. gadget) driver updates and additions
- new device ids for lots of drivers
- loads of other small updates, full details in the shortlog
All of these, including a "last minute regression fix" have been in
linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZfwpzA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymS9QCdEuF6KJFLOrDrGS4NbZNSUPIVF6oAn350r4NX
CMZah37Dfr1VDCOOV4gQ
=HACL
-----END PGP SIGNATURE-----
Merge tag 'usb-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.9-rc1. Lots
of tiny changes and forward progress to support new hardware and
better support for existing devices. Included in here are:
- Thunderbolt (i.e. USB4) updates for newer hardware and uses as more
people start to use the hardware
- default USB authentication mode Kconfig and documentation update to
make it more obvious what is going on
- USB typec updates and enhancements
- usual dwc3 driver updates
- usual xhci driver updates
- function USB (i.e. gadget) driver updates and additions
- new device ids for lots of drivers
- loads of other small updates, full details in the shortlog
All of these, including a "last minute regression fix" have been in
linux-next with no reported issues"
* tag 'usb-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (185 commits)
usb: usb-acpi: Fix oops due to freeing uninitialized pld pointer
usb: gadget: net2272: Use irqflags in the call to net2272_probe_fin
usb: gadget: tegra-xudc: Fix USB3 PHY retrieval logic
phy: tegra: xusb: Add API to retrieve the port number of phy
USB: gadget: pxa27x_udc: Remove unused of_gpio.h
usb: gadget/snps_udc_plat: Remove unused of_gpio.h
usb: ohci-pxa27x: Remove unused of_gpio.h
usb: sl811-hcd: only defined function checkdone if QUIRK2 is defined
usb: Clarify expected behavior of dev_bin_attrs_are_visible()
xhci: Allow RPM on the USB controller (1022:43f7) by default
usb: isp1760: remove SLAB_MEM_SPREAD flag usage
usb: misc: onboard_hub: use pointer consistently in the probe function
usb: gadget: fsl: Increase size of name buffer for endpoints
usb: gadget: fsl: Add of device table to enable module autoloading
usb: typec: tcpm: add support to set tcpc connector orientatition
usb: typec: tcpci: add generic tcpci fallback compatible
dt-bindings: usb: typec-tcpci: add tcpci fallback binding
usb: gadget: fsl-udc: Replace custom log wrappers by dev_{err,warn,dbg,vdbg}
usb: core: Set connect_type of ports based on DT node
dt-bindings: usb: Add downstream facing ports to realtek binding
...
This release sees some exciting changes from David Lechner which
implements some optimisations that have been talked about for a long
time which allows client drivers to pre-prepare SPI messages for
repeated or low latency use. This lets us move work out of latency
sensitive paths and avoid repeating work for frequently performed
operations. As well as being useful in itself this will also be used in
future to allow controllers to directly trigger SPI operations (eg, from
interrupts).
Otherwise this release has mostly been focused on cleanups, plus a
couple of new devices:
- Support for pre-optimising messages.
- A big set of updates from Uwe Kleine-König moving drivers to use APIs
with more modern terminology for controllers.
- Major overhaul of the s3c64xx driver.
- Support for Google GS101 and Samsung Exynos850.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmXvHx0ACgkQJNaLcl1U
h9ATVQf/WafEp7ddJ23bRaHZx/gBCMgv8N6mN7OBnzB2pMIGL56SPf9fGAmCUQKt
mne6fDg6/RpydG/72TFppUjRFLN9CwoJjJfQIXMgOqYuPaMEnrj1wbcXar3MeeX2
8hS1u7wKwhOuuwLmoqqMOTKyGUj2mHsBOTOo0vm4WM1s9IHhY5TG2clYv1A+KZbj
kSHE5m7YnBLwimwu0+hsXnRNHZUGKVksQ/9t7AD7/7L8aPj9jPqu1EjTS1/6IDB0
QDVyW7Z6hX7YoUx48gp+j/UFJ7ZyxTajy+0wvzPHou3KJARgFfNZWT2XvvYcpA0/
yqcpbCUwZ1AETXHcmly7YwNpPV9LBg==
=+Xw/
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This release sees some exciting changes from David Lechner which
implements some optimisations that have been talked about for a long
time which allows client drivers to pre-prepare SPI messages for
repeated or low latency use. This lets us move work out of latency
sensitive paths and avoid repeating work for frequently performed
operations. As well as being useful in itself this will also be used
in future to allow controllers to directly trigger SPI operations (eg,
from interrupts).
Otherwise this release has mostly been focused on cleanups, plus a
couple of new devices:
- Support for pre-optimising messages
- A big set of updates from Uwe Kleine-König moving drivers to use
APIs with more modern terminology for controllers
- Major overhaul of the s3c64xx driver
- Support for Google GS101 and Samsung Exynos850"
* tag 'spi-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (122 commits)
spi: Introduce SPI_INVALID_CS and is_valid_cs()
spi: Fix types of the last chip select storage variables
spi: Consistently use BIT for cs_index_mask
spi: Exctract spi_dev_check_cs() helper
spi: Exctract spi_set_all_cs_unused() helper
spi: s3c64xx: switch exynos850 to new port config data
spi: s3c64xx: switch gs101 to new port config data
spi: s3c64xx: deprecate fifo_lvl_mask, rx_lvl_offset and port_id
spi: s3c64xx: get rid of the OF alias ID dependency
spi: s3c64xx: introduce s3c64xx_spi_set_port_id()
spi: s3c64xx: let the SPI core determine the bus number
spi: s3c64xx: allow FIFO depth to be determined from the compatible
spi: s3c64xx: retrieve the FIFO depth from the device tree
spi: s3c64xx: determine the fifo depth only once
spi: s3c64xx: allow full FIFO masks
spi: s3c64xx: define a magic value
spi: dt-bindings: introduce FIFO depth properties
spi: axi-spi-engine: use struct_size() macro
spi: axi-spi-engine: use __counted_by() attribute
spi: axi-spi-engine: remove p from struct spi_engine_message_state
...
Currently the variable irqflags is being set but is not being used,
it appears it should be used in the call to net2272_probe_fin
rather than IRQF_TRIGGER_LOW being used. Kudos to Uwe Kleine-König
for suggesting the fix.
Cleans up clang scan build warning:
drivers/usb/gadget/udc/net2272.c:2610:15: warning: variable 'irqflags'
set but not used [-Wunused-but-set-variable]
Fixes: ceb80363b2 ("USB: net2272: driver for PLX NET2272 USB device controller")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240307181734.2034407-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit resolves an issue in the tegra-xudc USB gadget driver that
incorrectly fetched USB3 PHY instances. The problem stemmed from the
assumption of a one-to-one correspondence between USB2 and USB3 PHY
names and their association with physical USB ports in the device tree.
Previously, the driver associated USB3 PHY names directly with the USB3
instance number, leading to mismatches when mapping the physical USB
ports. For instance, if using USB3-1 PHY, the driver expect the
corresponding PHY name as 'usb3-1'. However, the physical USB ports in
the device tree were designated as USB2-0 and USB3-0 as we only have
one device controller, causing a misalignment.
This commit rectifies the issue by adjusting the PHY naming logic.
Now, the driver correctly correlates the USB2 and USB3 PHY instances,
allowing the USB2-0 and USB3-1 PHYs to form a physical USB port pair
while accurately reflecting their configuration in the device tree by
naming them USB2-0 and USB3-0, respectively.
The change ensures that the PHY and PHY names align appropriately,
resolving the mismatch between physical USB ports and their associated
names in the device tree.
Fixes: b4e19931c9 ("usb: gadget: tegra-xudc: Support multiple device modes")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20240307030328.1487748-3-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The custom log wrappers ERR, WARNING, DBG and VDBG don't add anything
useful that cannot easily be done with dev_err() and friends. Replace
the custom stuff by the well known functions from printk.h.
Also drop some dead code in a #if 0 block.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240304165404.807787-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While connecting to a Linux host with CDC_NCM_NTB_DEF_SIZE_TX
set to 65536, it has been observed that we receive short packets,
which come at interval of 5-10 seconds sometimes and have block
length zero but still contain 1-2 valid datagrams present.
According to the NCM spec:
"If wBlockLength = 0x0000, the block is terminated by a
short packet. In this case, the USB transfer must still
be shorter than dwNtbInMaxSize or dwNtbOutMaxSize. If
exactly dwNtbInMaxSize or dwNtbOutMaxSize bytes are sent,
and the size is a multiple of wMaxPacketSize for the
given pipe, then no ZLP shall be sent.
wBlockLength= 0x0000 must be used with extreme care, because
of the possibility that the host and device may get out of
sync, and because of test issues.
wBlockLength = 0x0000 allows the sender to reduce latency by
starting to send a very large NTB, and then shortening it when
the sender discovers that there’s not sufficient data to justify
sending a large NTB"
However, there is a potential issue with the current implementation,
as it checks for the occurrence of multiple NTBs in a single
giveback by verifying if the leftover bytes to be processed is zero
or not. If the block length reads zero, we would process the same
NTB infintely because the leftover bytes is never zero and it leads
to a crash. Fix this by bailing out if block length reads zero.
Cc: stable@vger.kernel.org
Fixes: 427694cfaa ("usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240228115441.2105585-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need it here for the USB fixes, and it resolves a merge conflict as
reported in linux-next in drivers/usb/roles/class.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the gadget_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240218-device_cleanup-usb-v1-3-77423c4da262@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is observed sometimes when tethering is used over NCM with Windows 11
as host, at some instances, the gadget_giveback has one byte appended at
the end of a proper NTB. When the NTB is parsed, unwrap call looks for
any leftover bytes in SKB provided by u_ether and if there are any pending
bytes, it treats them as a separate NTB and parses it. But in case the
second NTB (as per unwrap call) is faulty/corrupt, all the datagrams that
were parsed properly in the first NTB and saved in rx_list are dropped.
Adding a few custom traces showed the following:
[002] d..1 7828.532866: dwc3_gadget_giveback: ep1out:
req 000000003868811a length 1025/16384 zsI ==> 0
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb toprocess: 1025
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb seq: 0xce67
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x400
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb ndp_len: 0x10
[002] d..1 7828.532869: ncm_unwrap_ntb: K: Parsed NTB with 1 frames
In this case, the giveback is of 1025 bytes and block length is 1024.
The rest 1 byte (which is 0x00) won't be parsed resulting in drop of
all datagrams in rx_list.
Same is case with packets of size 2048:
[002] d..1 7828.557948: dwc3_gadget_giveback: ep1out:
req 0000000011dfd96e length 2049/16384 zsI ==> 0
[002] d..1 7828.557949: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.557950: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x800
Lecroy shows one byte coming in extra confirming that the byte is coming
in from PC:
Transfer 2959 - Bytes Transferred(1025) Timestamp((18.524 843 590)
- Transaction 8391 - Data(1025 bytes) Timestamp(18.524 843 590)
--- Packet 4063861
Data(1024 bytes)
Duration(2.117us) Idle(14.700ns) Timestamp(18.524 843 590)
--- Packet 4063863
Data(1 byte)
Duration(66.160ns) Time(282.000ns) Timestamp(18.524 845 722)
According to Windows driver, no ZLP is needed if wBlockLength is non-zero,
because the non-zero wBlockLength has already told the function side the
size of transfer to be expected. However, there are in-market NCM devices
that rely on ZLP as long as the wBlockLength is multiple of wMaxPacketSize.
To deal with such devices, it pads an extra 0 at end so the transfer is no
longer multiple of wMaxPacketSize.
Cc: <stable@vger.kernel.org>
Fixes: 9f6ce4240a ("usb: gadget: f_ncm.c added")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240205074650.200304-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When upgrading from 6.1 LTS to 6.6 LTS, I noticed the ethernet gadget
stopped working on Palm TE.
Commit 8825acd7cc ("ARM: omap1: remove dead code") deleted Palm TE from
machine_without_vbus_sense(), although the board is still used. Fix that.
Fixes: 8825acd7cc ("ARM: omap1: remove dead code")
Cc: stable <stable@kernel.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240217192042.GA372205@darkstar.musicnaut.iki.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an frame was transmitted incomplete to the host, we set the
UVC_STREAM_ERR bit in the header for the last request that is going
to be queued. This way the host will know that it should drop the
frame instead of trying to display the corrupted content.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-error-tag-v1-2-37659a3877fe@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the request that was missed was zero bytes long, it
is likely that the overall transferred frame was not affected.
So don't flag the frame incomplete in that case.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-error-tag-v1-1-37659a3877fe@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We refactor the complete handler since the return path with the
locking are really difficult to follow. Just simplify the function by
switching the logic return it on an disabled endpoint early. This way
the second level of indentation can be removed.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-gadget-cleanup-v1-3-de6d78780459@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pump function is running in an while(1) loop. The only case this
loop will be escaped is the two breaks. In both cases the req is valid.
Therefor the check for an not set req can be dropped and setting the req
to NULL does also has never any effect.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-gadget-cleanup-v1-1-de6d78780459@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces three new ioctls. They all should be called on a
data endpoint (ie. not ep0). They are:
- FUNCTIONFS_DMABUF_ATTACH, which takes the file descriptor of a DMABUF
object to attach to the endpoint.
- FUNCTIONFS_DMABUF_DETACH, which takes the file descriptor of the
DMABUF to detach from the endpoint. Note that closing the endpoint's
file descriptor will automatically detach all attached DMABUFs.
- FUNCTIONFS_DMABUF_TRANSFER, which requests a data transfer from / to
the given DMABUF. Its argument is a structure that packs the DMABUF's
file descriptor, the size in bytes to transfer (which should generally
be set to the size of the DMABUF), and a 'flags' field which is unused
for now.
Before this ioctl can be used, the related DMABUF must be attached
with FUNCTIONFS_DMABUF_ATTACH.
These three ioctls enable the FunctionFS code to transfer data between
the USB stack and a DMABUF object, which can be provided by a driver
from a completely different subsystem, in a zero-copy fashion.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20240130122340.54813-4-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new 'sg_was_mapped' field to the struct usb_request. This field
can be used to indicate that the scatterlist associated to the USB
transfer has already been mapped into the DMA space, and it does not
have to be done internally.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20240130122340.54813-2-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 8caab75fd2 ("spi: Generalize SPI "master" to "controller"")
some functions and struct members were renamed. To not break all drivers
compatibility macros were provided.
To be able to remove these compatibility macros push the renaming into
this driver.
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5caf03b6f321a9870aabb9282f1f22211d052740.1707324794.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
When a USB gadget is configured through configfs with 1 or more f_fs
functions, then the logic setting up the gadget configuration has to wait
until the user space code (typically separate applications) responsible for
those functions have written their descriptors before the gadget can be
activated.
The f_fs instance already knows if this has been done, so expose it through
a "ready" attribute in configfs for easier synchronization.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240126203208.2482573-1-peter@korsgaard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When write UDC to empty and unbind gadget driver from gadget device, it is
possible that there are many queue failures for mass storage function.
The root cause is mass storage main thread alaways try to queue request to
receive a command from host if running flag is on, on platform like dwc3,
if pull down called, it will not queue request again and return
-ESHUTDOWN, but it not affect running flag of mass storage function.
Check return code from mass storage function and clear running flag if it
is -ESHUTDOWN, also indicate start in/out transfer failure to break loops.
Cc: stable <stable@kernel.org>
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240123034829.3848409-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent commit [1] added support for changing max segment size of the NCM
interface via configfs. But the value of segment size value stored in
ncm_opts need to be converted to little endian before saving it in
ecm_desc. Also while initialising the value of segment size in opts during
instance allocation, the value ETH_FRAME_LEN needs to be assigned directly
without any conversion as ETH_FRAME_LEN and the variable max_segment_size
are native endian. The current implementaion modifies it into little endian
thus breaking things for big endian targets.
Fix endianness while assigning these variables.
While at it, fix up some stray spaces in comments added in code.
[1]: https://lore.kernel.org/all/20231221153216.18657-1-quic_kriskura@quicinc.com/
Fixes: 1900daeefd ("usb: gadget: ncm: Add support to update wMaxSegmentSize via configfs")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240118154910.8765-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaedng8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yndHACfX3SA2ipK5umpMsWOoLMCBV6VyrwAn3t+FPd/
z4mNiCuNUhbEnU7RinK0
=k/E9
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
A moderately busy release for SPI, the main core update was the merging
of support for multiple chip selects, used in some flash configurations.
There were also big overhauls for the AXI SPI Engine and PL022 drivers,
plus some new device support for ST.
There's a few patches for other trees, API updates to allow the
multiple chip select support and one of the naming modernisations
touched a controller embedded in the USB code.
- Support for multiple chip selects.
- A big overhaul for the AXI SPI engine driver, modernising it and
adding a bunch of new features.
- Modernisation of the PL022 driver, fixing some issues with submitting
messages while in atomic context in the process.
- Many drivers were converted to use new APIs which avoid outdated
terminology for devices and controllers.
- Support for ST Microelectronics STM32F7 and STM32MP25, and Renesas
RZ/Five.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmWbHmMACgkQJNaLcl1U
h9CpSwf+O981469g1twyEpq5PJlNgdXmrKUpezcC18X4DLXmlf5hoCsHUFIU2DuX
oBZuUQVp1KaEzJ4LX1giAOTuhfwPAItGR+/JMs6VxT/V0MMCHaNYcU5zLHXacDFL
URU7hyyhxUp9PzGNI/IEQH2DPv3QVX8Z1CVQQNQpnTsvbpBEF/osxB3SdWg65Y4J
B9nEW5hnyDsjxQVzjwCMFsy1vJeaBkP++zdPhPGE4RaNcweX+hksVRWVJ3DqUuJC
u4IyO5Hmduqmyjyc7MEV6lekecnyHc72WIzFXJpy0FOW0CstOQD59D5Fnbdvbb9i
mm3IJ1Vh/oepZBNPAmHCPqMEAqr5ZQ==
=49Kh
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A moderately busy release for SPI, the main core update was the
merging of support for multiple chip selects, used in some flash
configurations. There were also big overhauls for the AXI SPI Engine
and PL022 drivers, plus some new device support for ST.
There's a few patches for other trees, API updates to allow the
multiple chip select support and one of the naming modernisations
touched a controller embedded in the USB code.
- Support for multiple chip selects.
- A big overhaul for the AXI SPI engine driver, modernising it and
adding a bunch of new features.
- Modernisation of the PL022 driver, fixing some issues with
submitting messages while in atomic context in the process.
- Many drivers were converted to use new APIs which avoid outdated
terminology for devices and controllers.
- Support for ST Microelectronics STM32F7 and STM32MP25, and Renesas
RZ/Five"
* tag 'spi-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (83 commits)
spi: stm32: add st,stm32mp25-spi compatible supporting STM32MP25 soc
dt-bindings: spi: stm32: add st,stm32mp25-spi compatible
spi: stm32: use dma_get_slave_caps prior to configuring dma channel
spi: axi-spi-engine: fix struct member doc warnings
spi: pl022: update description of internal_cs_control()
spi: pl022: delete description of cur_msg
spi: dw: Remove Intel Thunder Bay SOC support
spi: dw: Remove Intel Thunder Bay SOC support
spi: sh-msiof: Enforce fixed DTDL for R-Car H3
spi: ljca: switch to use devm_spi_alloc_host()
spi: cs42l43: switch to use devm_spi_alloc_host()
spi: zynqmp-gqspi: switch to use modern name
spi: zynq-qspi: switch to use modern name
spi: xtensa-xtfpga: switch to use modern name
spi: xlp: switch to use modern name
spi: xilinx: switch to use modern name
spi: xcomm: switch to use modern name
spi: uniphier: switch to use modern name
spi: topcliff-pch: switch to use modern name
spi: wpcm-fiu: switch to use devm_spi_alloc_host()
...
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZZUxRQAKCRCRxhvAZXjc
ov/QAQDzvge3oQ9MEymmOiyzzcF+HhAXBr+9oEsYJjFc1p0TsgEA61gXjZo7F1jY
KBqd6znOZCR+Waj0kIVJRAo/ISRBqQc=
=0bRl
-----END PGP SIGNATURE-----
Merge tag 'vfs-6.8.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull misc vfs updates from Christian Brauner:
"This contains the usual miscellaneous features, cleanups, and fixes
for vfs and individual fses.
Features:
- Add Jan Kara as VFS reviewer
- Show correct device and inode numbers in proc/<pid>/maps for vma
files on stacked filesystems. This is now easily doable thanks to
the backing file work from the last cycles. This comes with
selftests
Cleanups:
- Remove a redundant might_sleep() from wait_on_inode()
- Initialize pointer with NULL, not 0
- Clarify comment on access_override_creds()
- Rework and simplify eventfd_signal() and eventfd_signal_mask()
helpers
- Process aio completions in batches to avoid needless wakeups
- Completely decouple struct mnt_idmap from namespaces. We now only
keep the actual idmapping around and don't stash references to
namespaces
- Reformat maintainer entries to indicate that a given subsystem
belongs to fs/
- Simplify fput() for files that were never opened
- Get rid of various pointless file helpers
- Rename various file helpers
- Rename struct file members after SLAB_TYPESAFE_BY_RCU switch from
last cycle
- Make relatime_need_update() return bool
- Use GFP_KERNEL instead of GFP_USER when allocating superblocks
- Replace deprecated ida_simple_*() calls with their current ida_*()
counterparts
Fixes:
- Fix comments on user namespace id mapping helpers. They aren't
kernel doc comments so they shouldn't be using /**
- s/Retuns/Returns/g in various places
- Add missing parameter documentation on can_move_mount_beneath()
- Rename i_mapping->private_data to i_mapping->i_private_data
- Fix a false-positive lockdep warning in pipe_write() for watch
queues
- Improve __fget_files_rcu() code generation to improve performance
- Only notify writer that pipe resizing has finished after setting
pipe->max_usage otherwise writers are never notified that the pipe
has been resized and hang
- Fix some kernel docs in hfsplus
- s/passs/pass/g in various places
- Fix kernel docs in ntfs
- Fix kcalloc() arguments order reported by gcc 14
- Fix uninitialized value in reiserfs"
* tag 'vfs-6.8.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (36 commits)
reiserfs: fix uninit-value in comp_keys
watch_queue: fix kcalloc() arguments order
ntfs: dir.c: fix kernel-doc function parameter warnings
fs: fix doc comment typo fs tree wide
selftests/overlayfs: verify device and inode numbers in /proc/pid/maps
fs/proc: show correct device and inode numbers in /proc/pid/maps
eventfd: Remove usage of the deprecated ida_simple_xx() API
fs: super: use GFP_KERNEL instead of GFP_USER for super block allocation
fs/hfsplus: wrapper.c: fix kernel-doc warnings
fs: add Jan Kara as reviewer
fs/inode: Make relatime_need_update return bool
pipe: wakeup wr_wait after setting max_usage
file: remove __receive_fd()
file: stop exposing receive_fd_user()
fs: replace f_rcuhead with f_task_work
file: remove pointless wrapper
file: s/close_fd_get_file()/file_close_fd()/g
Improve __fget_files_rcu() code generation (and thus __fget_light())
file: massage cleanup of files that failed to open
fs/pipe: Fix lockdep false-positive in watchqueue pipe_write()
...
When handling error status from uvcg_video_usb_req_queue,
uvc_video_complete currently calls uvcg_queue_cancel with
video->req_lock held. uvcg_queue_cancel internally locks
queue->irqlock, which nests queue->irqlock inside
video->req_lock. This isn't a functional bug at the
moment, but does open up possibilities for ABBA
deadlocks in the future.
This patch fixes the accidental nesting by dropping
video->req_lock before calling uvcg_queue_cancel.
Fixes: 6acba0345b ("usb:gadget:uvc Do not use worker thread to pump isoc usb requests")
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20240104215009.2252452-2-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a path that may lead to freed memory being referenced,
causing kernel panics.
The kernel panic has the following stack trace:
Workqueue: uvcgadget uvcg_video_pump.c51fb85fece46625450f86adbf92c56c.cfi_jt
pstate: 60c00085 (nZCv daIf +PAN +UAO -TCO BTYPE=--)
pc : __list_del_entry_valid+0xc0/0xd4
lr : __list_del_entry_valid+0xc0/0xd4
Call trace:
__list_del_entry_valid+0xc0/0xd4
uvc_video_free_request+0x60/0x98
uvcg_video_pump+0x1cc/0x204
process_one_work+0x21c/0x4b8
worker_thread+0x29c/0x574
kthread+0x158/0x1b0
ret_from_fork+0x10/0x30
The root cause is that uvcg_video_usb_req_queue frees the uvc_request
if is_enabled is false and returns an error status. video_pump also
frees the associated request if uvcg_video_usb_req_queue returns an
error status, leading to double free and accessing garbage memory.
To fix the issue, this patch removes freeing logic from
uvcg_video_usb_req_queue, and lets the callers to the function handle
queueing errors as they see fit.
Fixes: 6acba0345b ("usb:gadget:uvc Do not use worker thread to pump isoc usb requests")
Tested-by: Avichal Rakesh <arakesh@google.com>
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20240104215009.2252452-1-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 6.7-rc1, there was a netif_device_detach call added to the
gether_disconnect function. This clears the __LINK_STATE_PRESENT bit of
the netif device and suppresses pings (ICMP messages) and TCP connection
requests from the connected host. If userspace temporarily disconnects
the gadget, such as by temporarily removing configuration in the gadget
configfs interface, network activity should continue to be processed
when the gadget is re-connected. Mirror the netif_device_detach call
with a netif_device_attach call in gether_connect to fix re-connecting
gadgets.
Link: 6002e51b70/main/postmarketos-base-ui/rootfs-usr-lib-NetworkManager-dispatcher.d-50-tethering.sh
Cc: stable <stable@kernel.org>
Fixes: f49449fbc2 ("usb: gadget: u_ether: Replace netif_stop_queue with netif_device_detach")
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Tested-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20231218164532.411125-2-mailingradian@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3c5b006f3e.
gadget_is_{super|dual}speed() API check UDC controller capitblity. It
should pass down highest speed endpoint descriptor to UDC controller. So
UDC controller driver can reserve enough resource at check_config(),
especially mult and maxburst. So UDC driver (such as cdns3) can know need
at least (mult + 1) * (maxburst + 1) * wMaxPacketSize internal memory for
this uvc functions.
Cc: <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-5-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The max segment size is currently limited to the ethernet frame length of
the kernel which happens to be 1514 at this point in time. However the NCM
specification limits it to 64K for sixtenn bit NTB's. For peer to peer
connections, increasing the segment size gives better throughput.
Add support to configure this value before configfs symlink is created.
Also since the NTB Out/In buffer sizes are fixed at 16384 bytes, limit the
segment size to an upper cap of 8000 to allow at least a minimum of 2 MTU
sized datagrams to be aggregated.
Set the default MTU size for the ncm interface during function bind before
network interface is registered allowing MTU to be set in parity with
wMaxSegmentSize.
Update gadget documentation describing the new configfs property.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/20231221153216.18657-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 588b9e8560 ("usb: gadget: uvc: add v4l2 enumeration api calls")
has rendered the precomposed (aka legacy) webcam gadget unloadable.
uvc_alloc() since then has depended on certain config groups being
available in configfs tree related to the UVC function. However, legacy
gadgets do not create anything in configfs, so uvc_alloc() must fail
with -ENOENT no matter what.
This patch mimics the required configfs hierarchy to satisfy the code which
inspects formats and frames found in uvcg_streaming_header.
This has been tested with guvcview on the host side, using vivid as a
source of video stream on the device side and using the userspace program
found at https://gitlab.freedesktop.org/camera/uvc-gadget.git.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Fixes: 588b9e8560 ("usb: gadget: uvc: add v4l2 enumeration api calls")
Link: https://lore.kernel.org/r/20231215131614.29132-1-andrzej.p@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When compiling with gcc version 14.0.0 20231206 (experimental)
and CONFIG_FORTIFY_SOURCE=y, I've noticed the following warning:
...
In function 'fortify_memcpy_chk',
inlined from '__ffs_func_bind_do_os_desc' at drivers/usb/gadget/function/f_fs.c:2934:3:
./include/linux/fortify-string.h:588:25: warning: call to '__read_overflow2_field'
declared with attribute warning: detected read beyond size of field (2nd parameter);
maybe use struct_group()? [-Wattribute-warning]
588 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This call to 'memcpy()' is interpreted as an attempt to copy both
'CompatibleID' and 'SubCompatibleID' of 'struct usb_ext_compat_desc'
from an address of the first one, which causes an overread warning.
Since we actually want to copy both of them at once, use the
convenient 'struct_group()' and 'sizeof_field()' here.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://lore.kernel.org/r/20231214090428.27292-1-dmantipov@yandex.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231213164246.1021885-7-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Cristian Birsan <cristian.birsan@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231213164246.1021885-6-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Daniel Scally <dan.scally@ideasonboard.com>
Cc: Andrzej Pietrasiewicz <andrzejtp2010@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20231213164246.1021885-5-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: James Gruber <jimmyjgruber@gmail.com>
Cc: Yadwinder Singh <yadi.brar01@gmail.com>
Cc: Jaswinder Singh <jaswinder.singh@linaro.org>
Cc: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231213164246.1021885-4-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Cc: Julian Scheel <julian@jusst.de>
Cc: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231213164246.1021885-3-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231213164246.1021885-2-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 89ff3dfac6 ("usb: gadget: f_hid: fix f_hidg lifetime vs
cdev") has introduced a bug that leads to hid device corruption after
the replug operation.
Reverse device managed memory allocation for the report descriptor
to fix the issue.
Tested:
This change was tested on the AMD EthanolX CRB server with the BMC
based on the OpenBMC distribution. The BMC provides KVM functionality
via the USB gadget device:
- before: KVM page refresh results in a broken USB device,
- after: KVM page refresh works without any issues.
Fixes: 89ff3dfac6 ("usb: gadget: f_hid: fix f_hidg lifetime vs cdev")
Cc: stable@vger.kernel.org
Signed-off-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Link: https://lore.kernel.org/r/20231206080744.253-2-aladyshev22@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() has the documented, but still rather strange trait of
returning the length of the data that *would have been* written to the
array if space were available, rather than the arguably more useful
length of data *actually* written, it is usually considered wise to use
something else instead in order to avoid confusion.
In the case of sysfs call-backs, new wrappers exist that do just that.
This patch replaces just one use of snprintf() found in the sysfs
.show() call-back with the new sysfs_emit() helper.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Dmitry Bogdanov <d.bogdanov@yadro.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231130105459.3208986-6-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() has the documented, but still rather strange trait of
returning the length of the data that *would have been* written to the
array if space were available, rather than the arguably more useful
length of data *actually* written, it is usually considered wise to use
something else instead in order to avoid confusion.
In the case of sysfs call-backs, new wrappers exist that do just that.
This patch replaces just one use of snprintf() found in the sysfs
.show() call-back with the new sysfs_emit() helper.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231130105459.3208986-5-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The KOBJ_CHANGE uevent is sent before gadget unbind is actually
executed, resulting in inaccurate uevent emitted at incorrect timing
(the uevent would have USB_UDC_DRIVER variable set while it would
soon be removed).
Move the KOBJ_CHANGE uevent to the end of the unbind function so that
uevent is sent only after the change has been made.
Fixes: 2ccea03a8f ("usb: gadget: introduce UDC Class")
Cc: stable@vger.kernel.org
Signed-off-by: Roy Luo <royluo@google.com>
Link: https://lore.kernel.org/r/20231128221756.2591158-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ever since the eventfd type was introduced back in 2007 in commit
e1ad7468c7 ("signal/timer/event: eventfd core") the eventfd_signal()
function only ever passed 1 as a value for @n. There's no point in
keeping that additional argument.
Link: https://lore.kernel.org/r/20231122-vfs-eventfd-signal-v2-2-bd549b14ce0c@kernel.org
Acked-by: Xu Yilun <yilun.xu@intel.com>
Acked-by: Andrew Donnellan <ajd@linux.ibm.com> # ocxl
Acked-by: Eric Farman <farman@linux.ibm.com> # s390
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Christian Brauner <brauner@kernel.org>
When we use an async work queue to perform the function of pumping
usb requests to the usb controller, it is possible that amongst other
factors, thread scheduling affects at what cadence we're able to pump
requests. This could mean isoc usb requests miss their uframes - resulting
in video stream flickers on the host device.
To avoid this, we make the async_wq thread only produce isoc usb_requests
with uvc buffers encoded into them. The process of queueing to the
endpoint is done by the uvc_video_complete() handler. In case no
usb_requests are ready with encoded information, we just queue a zero
length request to the endpoint from the complete handler.
For bulk endpoints the async_wq thread still queues usb requests to the
endpoint.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jayant Chowdhary <jchowdhary@google.com>
Suggested-by: Avichal Rakesh <arakesh@google.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231120062026.3759463-1-jchowdhary@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the uvc gadget driver allocates all uvc_requests as one array
and deallocates them all when the video stream stops. This includes
de-allocating all the usb_requests associated with those uvc_requests.
This can lead to use-after-free issues if any of those de-allocated
usb_requests were still owned by the usb controller.
This is patch 2 of 2 in fixing the use-after-free issue. It adds a new
flag to uvc_video to track when frames and requests should be flowing.
When disabling the video stream, the flag is tripped and, instead
of de-allocating all uvc_requests and usb_requests, the gadget
driver only de-allocates those usb_requests that are currently
owned by it (as present in req_free). Other usb_requests are left
untouched until their completion handler is called which takes care
of freeing the usb_request and its corresponding uvc_request.
Now that uvc_video does not depends on uvc->state, this patch removes
unnecessary upates to uvc->state that were made to accommodate uvc_video
logic. This should ensure that uvc gadget driver never accidentally
de-allocates a usb_request that it doesn't own.
Link: https://lore.kernel.org/7cd81649-2795-45b6-8c10-b7df1055020d@google.com
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Suggested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20231109004104.3467968-4-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch refactors the video disable logic in uvcg_video_enable
into its own separate function 'uvcg_video_disable'. This function
is now used anywhere uvcg_video_enable(video, 0) was used.
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Suggested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20231109004104.3467968-3-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the uvc gadget driver allocates all uvc_requests as one array
and deallocates them all when the video stream stops. This includes
de-allocating all the usb_requests associated with those uvc_requests.
This can lead to use-after-free issues if any of those de-allocated
usb_requests were still owned by the usb controller.
This patch is 1 of 2 patches addressing the use-after-free issue.
Instead of bulk allocating all uvc_requests as an array, this patch
allocates uvc_requests one at a time, which should allows for similar
granularity when deallocating the uvc_requests. This patch has no
functional changes other than allocating each uvc_request separately,
and similarly freeing each of them separately.
Link: https://lore.kernel.org/7cd81649-2795-45b6-8c10-b7df1055020d@google.com
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Suggested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20231109004104.3467968-2-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the set_alt callback immediately disables the endpoint and queues
the v4l2 streamoff event. However, as the streamoff event is processed
asynchronously, it is possible that the video_pump thread attempts to queue
requests to an already disabled endpoint.
This change moves disabling usb endpoint to the end of streamoff event
callback. As the endpoint's state can no longer be used, video_pump is
now guarded by uvc->state as well. To be consistent with the actual
streaming state, uvc->state is now toggled between CONNECTED and STREAMING
from the v4l2 event callback only.
Link: https://lore.kernel.org/20230615171558.GK741@pendragon.ideasonboard.com/
Link: https://lore.kernel.org/20230531085544.253363-1-dan.scally@ideasonboard.com/
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20231109004104.3467968-1-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strlcpy() reads the entire source buffer first. This read may exceed
the destination size limit. This is both inefficient and can lead
to linear read overflows if a source string is not NUL-terminated[1].
Additionally, it returns the size of the source string, not the
resulting size of the destination string. In an effort to remove strlcpy()
completely[2], replace strlcpy() here with strscpy().
In the unlikely (impossible?) case where opts->id was larger than
PAGE_SIZE, this will now correctly report truncation errors.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy [1]
Link: https://github.com/KSPP/linux/issues/89 [2]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Will McVicker <willmcvicker@google.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Zhang Qilong <zhangqilong3@huawei.com>
Cc: Linyu Yuan <quic_linyyuan@quicinc.com>
Cc: John Keeping <john@keeping.me.uk>
Cc: Azeem Shaikh <azeemshaikh38@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20231116191452.work.902-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231120215830.71071-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231120215830.71071-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231120215830.71071-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231120215830.71071-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231120215830.71071-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SPI_MASTER_HALF_DUPLEX is the legacy name of a definition
for a half duplex flag. Since all others had been replaced with
the respective SPI_CONTROLLER prefix get rid of the last one
as well. There is no functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # for input
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20231113111249.3982461-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for new
hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio, spi,
and i2c drivers for that type of device (all acked by the respective
subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems, EXCEPT for some merge conflicts that you will run
into in your tree. 2 of them are in device-tree files, which will be
trivial to resolve (accept both sides), and the last in the
drivers/gpio/gpio-ljca.c file, in the remove callback, resolution should
be pretty trivial (take the version in this branch), see here:
https://lore.kernel.org/all/20231016134159.11d8f849@canb.auug.org.au/
for details, or I can provide a resolved merge point if needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZUStew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxgQCggUyfGo+JVV8XZVu5A9KwT6nr7mUAmwUgFxhZ
khK77t0KqF4hjXryeaHa
=iPd+
-----END PGP SIGNATURE-----
Merge tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for
new hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio,
spi, and i2c drivers for that type of device (all acked by the
respective subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
usb: gadget: uvc: Add missing initialization of ssp config descriptor
usb: storage: set 1.50 as the lower bcdDevice for older "Super Top" compatibility
usb: raw-gadget: report suspend, resume, reset, and disconnect events
usb: raw-gadget: don't disable device if usb_ep_queue fails
usb: raw-gadget: properly handle interrupted requests
usb:cdnsp: remove TRB_FLUSH_ENDPOINT command
usb: gadget: aspeed_udc: Convert to platform remove callback returning void
dt-bindings: usb: fsa4480: Add compatible for OCP96011
usb: typec: fsa4480: Add support to swap SBU orientation
dt-bindings: usb: fsa4480: Add data-lanes property to endpoint
usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm()
Revert "dt-bindings: usb: Add bindings for multiport properties on DWC3 controller"
Revert "dt-bindings: usb: qcom,dwc3: Add bindings for SC8280 Multiport"
thunderbolt: Fix one kernel-doc comment
usb: gadget: f_ncm: Always set current gadget in ncm_bind()
usb: core: Remove duplicated check in usb_hub_create_port_device
usb: typec: tcpm: Add additional checks for contaminant
arm64: dts: rockchip: rk3588s: Add USB3 host controller
usb: dwc3: add optional PHY interface clocks
dt-bindings: usb: add rk3588 compatible to rockchip,dwc3
...
Updates to the usual drivers (ufs, megaraid_sas, lpfc, target, ibmvfc,
scsi_debug) plus the usual assorted minor fixes and updates. The
major change this time around is a prep patch for rethreading of the
driver reset handler API not to take a scsi_cmd structure which starts
to reduce various drivers' dependence on scsi_cmd in error handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZUORLiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQ4WAQDDIhzp
/PiJBBtt0U9ii/lYqRLrOVnN0extKEgEGO+FbwEAssKgs+5Jn/7XCgdpSrx8Co3/
0cPXrZGxs7tFpFWLZjM=
=AlRU
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, megaraid_sas, lpfc, target, ibmvfc,
scsi_debug) plus the usual assorted minor fixes and updates.
The major change this time around is a prep patch for rethreading of
the driver reset handler API not to take a scsi_cmd structure which
starts to reduce various drivers' dependence on scsi_cmd in error
handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (132 commits)
scsi: ufs: core: Leave space for '\0' in utf8 desc string
scsi: ufs: core: Conversion to bool not necessary
scsi: ufs: core: Fix race between force complete and ISR
scsi: megaraid: Fix up debug message in megaraid_abort_and_reset()
scsi: aic79xx: Fix up NULL command in ahd_done()
scsi: message: fusion: Initialize return value in mptfc_bus_reset()
scsi: mpt3sas: Fix loop logic
scsi: snic: Remove useless code in snic_dr_clean_pending_req()
scsi: core: Add comment to target_destroy in scsi_host_template
scsi: core: Clean up scsi_dev_queue_ready()
scsi: pmcraid: Add missing scsi_device_put() in pmcraid_eh_target_reset_handler()
scsi: target: core: Fix kernel-doc comment
scsi: pmcraid: Fix kernel-doc comment
scsi: core: Handle depopulation and restoration in progress
scsi: ufs: core: Add support for parsing OPP
scsi: ufs: core: Add OPP support for scaling clocks and regulators
scsi: ufs: dt-bindings: common: Add OPP table
scsi: scsi_debug: Add param to control sdev's allow_restart
scsi: scsi_debug: Add debugfs interface to fail target reset
scsi: scsi_debug: Add new error injection type: Reset LUN failed
...
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R. Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)
-----BEGIN PGP SIGNATURE-----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=0iVF
-----END PGP SIGNATURE-----
Merge tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"One of the more voluminous set of changes is for adding the new
__counted_by annotation[1] to gain run-time bounds checking of
dynamically sized arrays with UBSan.
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R.
Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem
Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas
Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees
Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)"
* tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (56 commits)
hwmon: (acpi_power_meter) replace open-coded kmemdup_nul
reset: Annotate struct reset_control_array with __counted_by
kexec: Annotate struct crash_mem with __counted_by
virtio_console: Annotate struct port_buffer with __counted_by
ima: Add __counted_by for struct modsig and use struct_size()
MAINTAINERS: Include stackleak paths in hardening entry
string: Adjust strtomem() logic to allow for smaller sources
hardening: x86: drop reference to removed config AMD_IOMMU_V2
randstruct: Fix gcc-plugin performance mode to stay in group
mailbox: zynqmp: Annotate struct zynqmp_ipi_pdata with __counted_by
drivers: thermal: tsens: Annotate struct tsens_priv with __counted_by
irqchip/imx-intmux: Annotate struct intmux_data with __counted_by
KVM: Annotate struct kvm_irq_routing_table with __counted_by
virt: acrn: Annotate struct vm_memory_region_batch with __counted_by
hwmon: Annotate struct gsc_hwmon_platform_data with __counted_by
sparc: Annotate struct cpuinfo_tree with __counted_by
isdn: kcapi: replace deprecated strncpy with strscpy_pad
isdn: replace deprecated strncpy with strscpy
NFS/flexfiles: Annotate struct nfs4_ff_layout_segment with __counted_by
nfs41: Annotate struct nfs4_file_layout_dsaddr with __counted_by
...
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZTppYgAKCRCRxhvAZXjc
okIHAP9anLz1QDyMLH12ASuHjgBc0Of3jcB6NB97IWGpL4O21gEA46ohaD+vcJuC
YkBLU3lXqQ87nfu28ExFAzh10hG2jwM=
=m4pB
-----END PGP SIGNATURE-----
Merge tag 'vfs-6.7.ctime' of gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs
Pull vfs inode time accessor updates from Christian Brauner:
"This finishes the conversion of all inode time fields to accessor
functions as discussed on list. Changing timestamps manually as we
used to do before is error prone. Using accessors function makes this
robust.
It does not contain the switch of the time fields to discrete 64 bit
integers to replace struct timespec and free up space in struct inode.
But after this, the switch can be trivially made and the patch should
only affect the vfs if we decide to do it"
* tag 'vfs-6.7.ctime' of gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs: (86 commits)
fs: rename inode i_atime and i_mtime fields
security: convert to new timestamp accessors
selinux: convert to new timestamp accessors
apparmor: convert to new timestamp accessors
sunrpc: convert to new timestamp accessors
mm: convert to new timestamp accessors
bpf: convert to new timestamp accessors
ipc: convert to new timestamp accessors
linux: convert to new timestamp accessors
zonefs: convert to new timestamp accessors
xfs: convert to new timestamp accessors
vboxsf: convert to new timestamp accessors
ufs: convert to new timestamp accessors
udf: convert to new timestamp accessors
ubifs: convert to new timestamp accessors
tracefs: convert to new timestamp accessors
sysv: convert to new timestamp accessors
squashfs: convert to new timestamp accessors
server: convert to new timestamp accessors
client: convert to new timestamp accessors
...
In case the uvc gadget is super speed plus, the corresponding config
descriptor wasn't initialized. As a result, the host will not recognize
the devices when using super speed plus connection.
This patch initializes them to super speed descriptors.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shuzhen Wang <shuzhenwang@google.com>
Link: https://lore.kernel.org/r/20231027183440.1994315-1-shuzhenwang@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update USB_RAW_IOCTL_EVENT_FETCH to also report suspend, resume, reset,
and disconnect events.
This allows the code that emulates a USB device via Raw Gadget to handle
these events. For example, the device can restart enumeration when it
gets reset.
Also do not print a WARNING when the event queue overflows. With these new
events being queued, the queue might overflow if the device emulation code
stops fetching events.
Also print debug messages when a non-control event is received.
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/d610b629a5f32fb76c24012180743f7f0f1872c0.1698350424.git.andreyknvl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During device operation, the host might decide to reset a device emulated
via Raw Gadget. In this case, if the device emulation code has endpoint
requests queued, usb_ep_queue will fail with -ESHUTDOWN. Currently, this
disables the Raw Gadget device and makes the emulation code unable to
proceed.
Do not disable the Raw Gadget device if usb_ep_queue fails.
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/3c5df3dddb67623b4aeb11c5546370363e65d8e2.1698350424.git.andreyknvl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, if a USB request that was queued by Raw Gadget is interrupted
(via a signal), wait_for_completion_interruptible returns -ERESTARTSYS.
Raw Gadget then attempts to propagate this value to userspace as a return
value from its ioctls. However, when -ERESTARTSYS is returned by a syscall
handler, the kernel internally restarts the syscall.
This doesn't allow userspace applications to interrupt requests queued by
Raw Gadget (which is required when the emulated device is asked to switch
altsettings). It also violates the implied interface of Raw Gadget that a
single ioctl must only queue a single USB request.
Instead, make Raw Gadget do what GadgetFS does: check whether the request
was interrupted (dequeued with status == -ECONNRESET) and report -EINTR to
userspace.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Cc: stable <stable@kernel.org>
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/0db45b1d7cc466e3d4d1ab353f61d63c977fbbc5.1698350424.git.andreyknvl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
ast_udc_remove() is one of these functions that return an error code
after doing only a partial cleanup. Replace the core's error message by
a more drastic one and still convert the driver to .remove_new().
Note the only semantic change here is the changed error message.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231026221701.2521483-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, gadget assignment to the net device occurred exclusively
during the initial binding attempt.
Nevertheless, the gadget pointer could change during bind/unbind
cycles due to various conditions, including the unloading/loading
of the UDC device driver or the detachment/reconnection of an
OTG-capable USB hub device.
This patch relocates the gether_set_gadget() function out from
ncm_opts->bound condition check, ensuring that the correct gadget
is assigned during each bind request.
The provided logs demonstrate the consistency of ncm_opts throughout
the power cycle, while the gadget may change.
* OTG hub connected during boot up and assignment of gadget and
ncm_opts pointer
[ 2.366301] usb 2-1.5: New USB device found, idVendor=2996, idProduct=0105
[ 2.366304] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.366306] usb 2-1.5: Product: H2H Bridge
[ 2.366308] usb 2-1.5: Manufacturer: Aptiv
[ 2.366309] usb 2-1.5: SerialNumber: 13FEB2021
[ 2.427989] usb 2-1.5: New USB device found, VID=2996, PID=0105
[ 2.428959] dabridge 2-1.5:1.0: dabridge 2-4 total endpoints=5, 0000000093a8d681
[ 2.429710] dabridge 2-1.5:1.0: P(0105) D(22.06.22) F(17.3.16) H(1.1) high-speed
[ 2.429714] dabridge 2-1.5:1.0: Hub 2-2 P(0151) V(06.87)
[ 2.429956] dabridge 2-1.5:1.0: All downstream ports in host mode
[ 2.430093] gadget 000000003c414d59 ------> gadget pointer
* NCM opts and associated gadget pointer during First ncm_bind
[ 34.763929] NCM opts 00000000aa304ac9
[ 34.763930] NCM gadget 000000003c414d59
* OTG capable hub disconnecte or assume driver unload.
[ 97.203114] usb 2-1: USB disconnect, device number 2
[ 97.203118] usb 2-1.1: USB disconnect, device number 3
[ 97.209217] usb 2-1.5: USB disconnect, device number 4
[ 97.230990] dabr_udc deleted
* Reconnect the OTG hub or load driver assaign new gadget pointer.
[ 111.534035] usb 2-1.1: New USB device found, idVendor=2996, idProduct=0120, bcdDevice= 6.87
[ 111.534038] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 111.534040] usb 2-1.1: Product: Vendor
[ 111.534041] usb 2-1.1: Manufacturer: Aptiv
[ 111.534042] usb 2-1.1: SerialNumber: Superior
[ 111.535175] usb 2-1.1: New USB device found, VID=2996, PID=0120
[ 111.610995] usb 2-1.5: new high-speed USB device number 8 using xhci-hcd
[ 111.630052] usb 2-1.5: New USB device found, idVendor=2996, idProduct=0105, bcdDevice=21.02
[ 111.630055] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 111.630057] usb 2-1.5: Product: H2H Bridge
[ 111.630058] usb 2-1.5: Manufacturer: Aptiv
[ 111.630059] usb 2-1.5: SerialNumber: 13FEB2021
[ 111.687464] usb 2-1.5: New USB device found, VID=2996, PID=0105
[ 111.690375] dabridge 2-1.5:1.0: dabridge 2-8 total endpoints=5, 000000000d87c961
[ 111.691172] dabridge 2-1.5:1.0: P(0105) D(22.06.22) F(17.3.16) H(1.1) high-speed
[ 111.691176] dabridge 2-1.5:1.0: Hub 2-6 P(0151) V(06.87)
[ 111.691646] dabridge 2-1.5:1.0: All downstream ports in host mode
[ 111.692298] gadget 00000000dc72f7a9 --------> new gadget ptr on connect
* NCM opts and associated gadget pointer during second ncm_bind
[ 113.271786] NCM opts 00000000aa304ac9 -----> same opts ptr used during first bind
[ 113.271788] NCM gadget 00000000dc72f7a9 ----> however new gaget ptr, that will not set
in net_device due to ncm_opts->bound = true
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Link: https://lore.kernel.org/r/20231020153324.82794-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-14-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases, like with multiple LUN targets or where the target has to
respond to transport level requests from the receiving context it can be
better to defer cmd submission to a helper thread. If the backend driver
blocks on something like request/tag allocation it can block the entire
target submission path and other LUs and transport IO on that session.
In other cases like single LUN targets with storage that can support all
the commands that the target can queue, then it's best to submit the cmd
to the backend from the target's cmd receiving context.
Subsequent commits will allow the user to config what they prefer, but
drivers like loop can't directly submit because they can be called from a
context that can't sleep. And, drivers like vhost-scsi can support direct
submission, but need to keep their default behavior of deferring execution
to avoid possible regressions where the backend can block.
Make the drivers tell LIO core if they support direct submissions and their
current default, so we can prevent users from misconfiguring the system and
initialize devices correctly.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230928020907.5730-2-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231009211356.3242037-16-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces the usage of netif_stop_queue with netif_device_detach
in the u_ether driver. The netif_device_detach function not only stops all
tx queues by calling netif_tx_stop_all_queues but also marks the device as
removed by clearing the __LINK_STATE_PRESENT bit.
This change helps notify user space about the disconnection of the device
more effectively, compared to netif_stop_queue, which only stops a single
transmit queue.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Link: https://lore.kernel.org/r/20231006155646.12938-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3a63f86c6a.
Based on review comments, it was applied too soon and needs more work.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20231005081716.GA13853@pendragon.ideasonboard.com
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 52a39f2cf6.
Based on review comments, it was applied too soon and needs more work.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20231005081716.GA13853@pendragon.ideasonboard.com
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit bb00788bd6.
Based on review comments, it was applied too soon and needs more work.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20231005081716.GA13853@pendragon.ideasonboard.com
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add "c_terminal_type" and "p_terminal_type" configfs entries
in order to allow the user to change the capture and playback terminal
type codes.
These fields affect the type of audio device that Windows detects, so
being able to modify this is useful when it would be advantageous for
a gadget to be detected as something other than a generic
speaker/microphone.
The fields default to microphone for the capture type field and speaker
for the playback type field as was the case before.
Signed-off-by: James Gruber <jimmyjgruber@gmail.com>
Link: https://lore.kernel.org/r/20230914222746.155126-1-jimmyjgruber@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct f_midi.
Additionally, since the element count member must be set before accessing
the annotated flexible array member, move its initialization earlier.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: John Keeping <john@keeping.me.uk>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Hulk Robot <hulkci@huawei.com>
Cc: Allen Pais <allen.lkml@gmail.com>
Cc: Will McVicker <willmcvicker@google.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Zhang Qilong <zhangqilong3@huawei.com>
Cc: linux-usb@vger.kernel.org
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915195938.never.611-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct ffs_buffer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: John Keeping <john@keeping.me.uk>
Cc: Udipto Goswami <quic_ugoswami@quicinc.com>
Cc: Linyu Yuan <quic_linyyuan@quicinc.com>
Cc: linux-usb@vger.kernel.org
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915195849.never.275-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Return USB_GADGET_DELAYED_STATUS from the setup() callback for 0-length
transfers as a workaround to stop some UDC drivers (e.g. dwc3) from
automatically proceeding with the status stage.
This workaround should be removed once all UDC drivers are fixed to
always delay the status stage until a response is queued to EP0.
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/a8d2b91f9890dc21daa359183e84879ff4525180.1693237258.git.andreyknvl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return USB_GADGET_DELAYED_STATUS from the setup() callback for 0-length
transfers as a workaround to stop some UDC drivers (e.g. dwc3) from
automatically proceeding with the status stage.
This workaround should be removed once all UDC drivers are fixed to
always delay the status stage until a response is queued to EP0.
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/c56077322f0d3fc6d504092a266cb89d75701087.1693237258.git.andreyknvl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uvc_video_enable function is calling cancel_work_sync which will be
blocking as long as new requests will be queued with the while loop. To
ensure an earlier stop in the pumping loop in this particular case we
rework the worker to requeue itself on every requests. Since the worker
is already running prioritized, the scheduling overhad did not have real
impact on the performance.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230911140530.2995138-4-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uvc_video_enable function of the uvc-gadget driver is dequeing and
immediately deallocs all requests on its disable codepath. This is not
save since the dequeue function is async and does not ensure that the
requests are left unlinked in the controller driver.
By adding the ep_free_request into the completion path of the requests
we ensure that the request will be properly deallocated.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230911140530.2995138-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the uvc-video gadget driver is using the v4l2 interface,
the streamon and streamoff can be triggered at any times. To ensure
that the pump worker will be closed as soon the userspace is
calling streamoff we synchronize the state of the gadget ensuring
the pump worker to bail out.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230911140530.2995138-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the event gadget_connect call (which invokes pullup) fails,
propagate the error to udc bind operation which in turn sends the
error to configfs. The userspace can then retry enumeration if
it chooses to.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230927073027.27952-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When NCM is used with hosts like Windows PC, it is observed that there are
multiple NTB's contained in one usb request giveback. Since the driver
unwraps the obtained request data assuming only one NTB is present, we
loose the subsequent NTB's present resulting in data loss.
Fix this by checking the parsed block length with the obtained data
length in usb request and continue parsing after the last byte of current
NTB.
Cc: stable@vger.kernel.org
Fixes: 9f6ce4240a ("usb: gadget: f_ncm.c added")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20230927105858.12950-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
Here is the big set of USB, Thunderbolt, and PHY driver updates for
6.6-rc1. Included in here are:
- PHY driver additions and cleanups
- Thunderbolt minor additions and fixes
- USB MIDI 2 gadget support added
- dwc3 driver updates and additions
- Removal of some old USB wireless code that was missed when that
codebase was originally removed a few years ago, cleaning up some
core USB code paths
- USB core potential use-after-free fixes that syzbot from different
people/groups keeps tripping over
- typec updates and additions
- gadget fixes and cleanups
- loads of smaller USB core and driver cleanups all over the place
Full details are in the shortlog. All of these have been in linux-next
for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPIAOQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn80gCgybzMp0YnSildFetSC8lUJTnzjQcAn3KWzb75
Zt72jxGl4ZOXHEpozG4O
=FLrK
-----END PGP SIGNATURE-----
Merge tag 'usb-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt / PHY driver updates from Greg KH:
"Here is the big set of USB, Thunderbolt, and PHY driver updates for
6.6-rc1. Included in here are:
- PHY driver additions and cleanups
- Thunderbolt minor additions and fixes
- USB MIDI 2 gadget support added
- dwc3 driver updates and additions
- Removal of some old USB wireless code that was missed when that
codebase was originally removed a few years ago, cleaning up some
core USB code paths
- USB core potential use-after-free fixes that syzbot from different
people/groups keeps tripping over
- typec updates and additions
- gadget fixes and cleanups
- loads of smaller USB core and driver cleanups all over the place
Full details are in the shortlog. All of these have been in linux-next
for a while with no reported problems"
* tag 'usb-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
platform/chrome: cros_ec_typec: Configure Retimer cable type
tcpm: Avoid soft reset when partner does not support get_status
usb: typec: tcpm: reset counter when enter into unattached state after try role
usb: typec: tcpm: set initial svdm version based on pd revision
USB: serial: option: add FOXCONN T99W368/T99W373 product
USB: serial: option: add Quectel EM05G variant (0x030e)
usb: dwc2: add pci_device_id driver_data parse support
usb: gadget: remove max support speed info in bind operation
usb: gadget: composite: cleanup function config_ep_by_speed_and_alt()
usb: gadget: config: remove max speed check in usb_assign_descriptors()
usb: gadget: unconditionally allocate hs/ss descriptor in bind operation
usb: gadget: f_uvc: change endpoint allocation in uvc_function_bind()
usb: gadget: add a inline function gether_bitrate()
usb: gadget: use working speed to calcaulate network bitrate and qlen
dt-bindings: usb: samsung,exynos-dwc3: Add Exynos850 support
usb: dwc3: exynos: Add support for Exynos850 variant
usb: gadget: udc-xilinx: fix incorrect type in assignment warning
usb: gadget: udc-xilinx: fix cast from restricted __le16 warning
usb: gadget: udc-xilinx: fix restricted __le16 degrades to integer warning
USB: dwc2: hande irq on dead controller correctly
...
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZOXTKAAKCRCRxhvAZXjc
oifJAQCzi/p+AdQu8LA/0XvR7fTwaq64ZDCibU4BISuLGT2kEgEAuGbuoFZa0rs2
XYD/s4+gi64p9Z01MmXm2XO1pu3GPg0=
=eJz5
-----END PGP SIGNATURE-----
Merge tag 'v6.6-vfs.ctime' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs timestamp updates from Christian Brauner:
"This adds VFS support for multi-grain timestamps and converts tmpfs,
xfs, ext4, and btrfs to use them. This carries acks from all relevant
filesystems.
The VFS always uses coarse-grained timestamps when updating the ctime
and mtime after a change. This has the benefit of allowing filesystems
to optimize away a lot of metadata updates, down to around 1 per
jiffy, even when a file is under heavy writes.
Unfortunately, this has always been an issue when we're exporting via
NFSv3, which relies on timestamps to validate caches. A lot of changes
can happen in a jiffy, so timestamps aren't sufficient to help the
client decide to invalidate the cache.
Even with NFSv4, a lot of exported filesystems don't properly support
a change attribute and are subject to the same problems with timestamp
granularity. Other applications have similar issues with timestamps
(e.g., backup applications).
If we were to always use fine-grained timestamps, that would improve
the situation, but that becomes rather expensive, as the underlying
filesystem would have to log a lot more metadata updates.
This introduces fine-grained timestamps that are used when they are
actively queried.
This uses the 31st bit of the ctime tv_nsec field to indicate that
something has queried the inode for the mtime or ctime. When this flag
is set, on the next mtime or ctime update, the kernel will fetch a
fine-grained timestamp instead of the usual coarse-grained one.
As POSIX generally mandates that when the mtime changes, the ctime
must also change the kernel always stores normalized ctime values, so
only the first 30 bits of the tv_nsec field are ever used.
Filesytems can opt into this behavior by setting the FS_MGTIME flag in
the fstype. Filesystems that don't set this flag will continue to use
coarse-grained timestamps.
Various preparatory changes, fixes and cleanups are included:
- Fixup all relevant places where POSIX requires updating ctime
together with mtime. This is a wide-range of places and all
maintainers provided necessary Acks.
- Add new accessors for inode->i_ctime directly and change all
callers to rely on them. Plain accesses to inode->i_ctime are now
gone and it is accordingly rename to inode->__i_ctime and commented
as requiring accessors.
- Extend generic_fillattr() to pass in a request mask mirroring in a
sense the statx() uapi. This allows callers to pass in a request
mask to only get a subset of attributes filled in.
- Rework timestamp updates so it's possible to drop the @now
parameter the update_time() inode operation and associated helpers.
- Add inode_update_timestamps() and convert all filesystems to it
removing a bunch of open-coding"
* tag 'v6.6-vfs.ctime' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (107 commits)
btrfs: convert to multigrain timestamps
ext4: switch to multigrain timestamps
xfs: switch to multigrain timestamps
tmpfs: add support for multigrain timestamps
fs: add infrastructure for multigrain timestamps
fs: drop the timespec64 argument from update_time
xfs: have xfs_vn_update_time gets its own timestamp
fat: make fat_update_time get its own timestamp
fat: remove i_version handling from fat_update_time
ubifs: have ubifs_update_time use inode_update_timestamps
btrfs: have it use inode_update_timestamps
fs: drop the timespec64 arg from generic_update_time
fs: pass the request_mask to generic_fillattr
fs: remove silly warning from current_time
gfs2: fix timestamp handling on quota inodes
fs: rename i_ctime field to __i_ctime
selinux: convert to ctime accessor functions
security: convert to ctime accessor functions
apparmor: convert to ctime accessor functions
sunrpc: convert to ctime accessor functions
...
Take ecm_bind() for example, it call gadget_is_{*}speed() API to show
gadget max support speed, it is not much help, remove the API usage here
is safe.
Similar change apply to acm,eem,loopback,ncm,obex,rndis,serial,
sourcesink,subset functions.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/20230803091053.9714-8-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When call this function, gadget already have working speed, if it is
USB_SPEED_SUPER_PLUS, in theroy gadget_is_superspeed_plus() checking
should be true, so there is no need to call it. it is same for other
working speed.
Remove all gadget_is_{*}speed_plus() API call to clean it up.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/20230803091053.9714-7-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_assign_descriptors() usally called inside function bind operation,
and gadget still have no working connection speed, let's support all
speed at this point, it may possible allocate extra memory to store
descriptors, but it is small and acceptable.
Remove gadget_is_{*}speed() API checking to allow support all speed.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/20230803091053.9714-6-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take f_midi_bind() for example, when composite layer call it, it will
allocate hs descriptor by calling gadget_is_dualspeed() API to check
gadget max support speed capability, but most other gadget function didn't
do like this.
To follow other function drivers, it is safe to remove the check which
mean support all possible link speed by default in function driver.
Similar change apply to midi2 and uvc.
Also in midi and midi2, as there is no descriptor difference between
super speed and super speed plus, follow other gadget function drivers,
do not allocate descriptor for super speed plus, composite layer will
handle it properly.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/20230803091053.9714-5-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when call uvc_function_bind(), gadget still have no connection speed,
just follow other gadget function, use fs endpoint descriptor to allocate
a video endpoint, remove gadget_is_{super|dual}speed() API call.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/20230803091053.9714-4-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function ecm_bitrate(), it is not support report bit rate for super
speed plus mode, but it can use same bit rate value defined in ncm and
rndis.
Add a common inline function gether_bitrate() which report different for
all possible speeds, it can be used by ecm, ncm and rndis, also remove
old function from them.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/20230803091053.9714-3-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take ecm_bitrate() as example, it will be called after gadget device
link speed negotiation, consider code
if (gadget_is_superspeed(g) && g->speed == USB_SPEED_SUPER),
if a gadget device link speed is USB_SPEED_SUPER,
gadget_is_superspeed(g) must be true, or not it is a wrong
configuration of gadget max support speed.
Remove gadget_is_superspeed(g) checking should be safe, and remove other
similar operation in ncm, rndis, u_ether.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/20230803091053.9714-2-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bitwise attribute is used by the sparse utility to make sure the
variable is converted to the local processor type before other (unsafe)
operations are performed on the variable. Fix the below sparse warnings
type casted with __le16:
warning: incorrect type in assignment (different base types)
expected unsigned short [usertype]
got restricted __le16 [usertype]
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/all/202209020044.CX2PfZzM-lkp@intel.com/
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20230822063201.16929-4-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a "variable set but not used" warning in f_mass_storage.c. rc is
used if verbose debugging is enabled but not otherwise.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: d5e2b67aae ("USB: g_mass_storage: template f_mass_storage.c file created")
Link: https://lore.kernel.org/r/cfed16c7-aa46-494b-ba84-b0e0dc99be3a@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here. Remove of_match_ptr() and CONFIG_OF.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230809084849.2410477-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avichal Rakesh reported a kernel panic that occurred when the UVC
gadget driver was removed from a gadget's configuration. The panic
involves a somewhat complicated interaction between the kernel driver
and a userspace component (as described in the Link tag below), but
the analysis did make one thing clear: The Gadget core should
accomodate gadget drivers calling usb_gadget_deactivate() as part of
their unbind procedure.
Currently this doesn't work. gadget_unbind_driver() calls
driver->unbind() while holding the udc->connect_lock mutex, and
usb_gadget_deactivate() attempts to acquire that mutex, which will
result in a deadlock.
The simple fix is for gadget_unbind_driver() to release the mutex when
invoking the ->unbind() callback. There is no particular reason for
it to be holding the mutex at that time, and the mutex isn't held
while the ->bind() callback is invoked. So we'll drop the mutex
before performing the unbind callback and reacquire it afterward.
We'll also add a couple of comments to usb_gadget_activate() and
usb_gadget_deactivate(). Because they run in process context they
must not be called from a gadget driver's ->disconnect() callback,
which (according to the kerneldoc for struct usb_gadget_driver in
include/linux/usb/gadget.h) may run in interrupt context. This may
help prevent similar bugs from arising in the future.
Reported-and-tested-by: Avichal Rakesh <arakesh@google.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 286d9975a8 ("usb: gadget: udc: core: Prevent soft_connect_store() race")
Link: https://lore.kernel.org/linux-usb/4d7aa3f4-22d9-9f5a-3d70-1bd7148ff4ba@google.com/
Cc: Badhri Jagan Sridharan <badhri@google.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/48b2f1f1-0639-46bf-bbfc-98cb05a24914@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NULL initialization of the pointers assigned by kzalloc() first is
not necessary, because if the kzalloc() failed, the pointers will be
assigned NULL, otherwise it works as usual. so remove it.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230804093253.91647-2-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a warning reported by coccinelle:
./drivers/usb/gadget/udc/renesas_usbf.c:3381:3-8:
No need to set .owner here. The core will do it.
The module_platform_driver() will set "THIS_MODULE" to driver.owner
when register a driver for platform-level devices, so it is redundant
initialization to set driver.owner in udc_driver statement. Remove it
to silence the warning.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Acked-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230803032838.3045730-1-lizetao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When platform_get_irq() fails, it may return -EPROBE_DEFER, which
suggested deferred probing, it is very important to propagate it
upstream. We cannot override it with other error code.
Commit ce753ad154 ("platform: finally disallow IRQ0 in
platform_get_irq() and its ilk") makes sure IRQ0 is not returned.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Link: https://lore.kernel.org/r/20230804110005.97061-1-wangzhu9@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here for testing and for other patches to be
applied on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the error path in f_midi2_block_opts_create(), mutex_unlock() is missed,
fix it by move the unlock after 'out' label.
Fixes: 29ee7a4ddd ("usb: gadget: midi2: Add configfs support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230728085120.3192474-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Link: https://lore.kernel.org/r/20230726113816.888-8-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230726113816.888-7-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230726113816.888-6-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230726113816.888-5-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch allows users to set up MIDI 1.0 ports more flexibly.
Namely, instead of the fixed mapping only from FB 0, now multiple
block definitions are applied to build up the MIDI 1.0 mapping.
The each block config has midi1_first_group and midi1_num_groups
attributes, and those specify which Groups are used for MIDI 1.0.
Those fields must be within the UMP Groups defined in the block
itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-8-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new ALSA control element to watch the current operation mode
(MIDI 1.0 or MIDI 2.0). It's a read-only control that reflects the
current value of altsetting, and 0 means unused, 1 for MIDI 1.0
(altset 0) and 2 for MIDI 2.0 (altset 1).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-7-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch extends MIDI 2.0 function driver to add more proper support
for MIDI 1.0 interface. Before this patch, the driver only exposes
the USB descriptor of a MIDI 1.0 interface in altset 0 while no actual
I/O is running for it. This patch enables the actual I/O for the
altset 0; the backend UMP rawmidi is translated from/to the MIDI 1.0
USB commands.
For converting to USB MIDI 1.0 data protocol, a helper function is
copied from the existing f_midi driver, in addition to a few other UMP
Core helper functions. For the MIDI 1.0 OUT (that is, input for
gadget), the incoming USB MIDI 1.0 packet is translated to UMP packets
via UMP Core helper, and tossed to the attached UMP rawmidi. It's a
relatively straightforward. OTOH, for MIDI 1.0 IN (i.e. output for
gadget), it's a bit more complex: we need to convert a source UMP
packet once to the standard MIDI 1.0 byte stream, and convert it again
to USB MIDI 1.0 packets, then send them out.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-5-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch extends MIDI 2.0 function driver to deal with more MIDI1
Jacks depending on the given Block configuration.
For MIDI 1.0, we take the configuration given in Function Block 0, and
create MIDI Jacks and Endpoints depending on the definition there.
That is, when more UMP Groups are defined in the Block 0, the
corresponding MIDI1 Jacks will be created.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-4-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the support of configfs to MIDI 2.0 function driver
for users to allow configuring the UMP Endpoint and Function Blocks
more flexibly. The configuration is in a tree form. The top-most
contains some card-level configurations. UMP Endpoints are defined in
subdirectories (ep.0, ep.1, etc) that contain Endpoint-specific
configurations such as ep_name, etc. And, UMP Function Blocks are
defined in the subdirectories (block.0, block.1, etc) under EP
subdirectory. As default, the driver creates a single UMP Endpoint
(ep.0) and a single Function Block (block.0) to work in a minimalistic
manner. User can modify those attributes freely to fit with the
demands.
When multiple Function Blocks are required, user can create another
directory as block.1, block.2, and so on (up to block.31). A block.*
directory can be deleted dynamically, too. A caveat is that the block
number has to be continuous.
Similarly, when multiple UMP Endpoints are required, user can create
another directory as ep.1, ep.2, up to ep.3.
Also, some driver behavior can be controlled in the card top-level
configs. e.g. you can pass process_ump=0 to disable the processing of
UMP Stream messages. This would be equivalent with the older MIDI 2.0
spec that doesn't support UMP v1.1 features.
The configfs interface checks upper- / lower-bound of input values,
and more sanity checks are performed at binding.
Attributes can't be changed any longer once when the instance is
linked to UDC.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-3-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the support for USB MIDI 2.0 gadget function driver.
The driver emulates a USB MIDI 2.0 interface with one or more UMP
Endpoints, where each of UMP Endpoint is a pair of MIDI Endpoints for
handling MIDI 2.0 UMP packets. When the function driver is bound, the
driver creates an ALSA card object with UMP rawmidi devices. This is
a kind of loop-back where the incoming and upcoming UMP packets
from/to the MIDI 2.0 UMP Endpoints are transferred as-is. In
addition, legacy (MIDI 1.0) rawmidi devices are created, so that
legacy applications can work in the gadget side, too.
When a USB MIDI 2.0 gadget interface appears, the connected host can
use it with the snd-usb-audio driver where MIDI 2.0 support is
enabled. Both gadget and connected hosts will have the similar UMP
Endpoint and Function Block (or Group Terminal Block) information.
Slight differences are the direction and UI-hint bits; it's due to the
nature of gadget driver, and the input/output direction is swapped in
both sides (the input for gadget is the output for host, and vice
versa).
The driver supports the brand-new UMP v1.1 feature, including the UMP
Stream message handling for providing UMP Endpoint and Function Block
information as well as dealing with the MIDI protocol switch. The
driver responds to UMP Stream messages by itself. OTOH, MIDI-CI
message handling isn't implemented in the kernel driver; it should be
processed in the user-space through the loopback UMP device.
As of this patch, the whole configuration is fixed, providing only one
bidirectional UMP Endpoint containing a single FB/GTB with a single
UMP Group. The configuration will be dynamically changeable in the
following patches.
The traditional MIDI 1.0 is still provided in the altset 0 (which is
mandatory per spec). But it's only about the configuration, and no
actual I/O will be running for the altset 0 as of this patch. The
proper support MIDI 1.0 altset will follow in later patches, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-2-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718143027.1064731-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should verify the bound of the array to assure that host
may not manipulate the index to point past endpoint array.
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20230628081511.186850-1-make_ruc2021@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The legacy gadget driver omitted calling usb_gadget_check_config()
to ensure that the USB device controller (UDC) has adequate resources,
including sufficient endpoint numbers and types, to support the given
configuration.
Previously, usb_add_config() was solely invoked by the legacy gadget
driver. Adds the necessary usb_gadget_check_config() after the bind()
operation to fix the issue.
Fixes: dce49449e0 ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230707230015.494999-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f08aa7c80d.
The reverted commit was based on static analysis and a misunderstanding
of how PTR_ERR() and NULLs are supposed to work. When a function
returns both pointer errors and NULL then normally the NULL means
"continue operating without a feature because it was deliberately
turned off". The NULL should not be treated as a failure. If a driver
cannot work when that feature is disabled then the KConfig should
enforce that the function cannot return NULL. We should not need to
test for it.
In this driver, the bug means that probe cannot succeed when CONFIG_PM
is disabled.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: f08aa7c80d ("usb: gadget: tegra-xudc: Fix error check in tegra_xudc_powerdomain_init()")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/ZKQoBa84U/ykEh3C@moroto
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In later patches, we're going to change how the inode's ctime field is
used. Switch to using accessor functions instead of raw accesses of
inode->i_ctime.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Message-Id: <20230705190309.579783-18-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Here is the big set of USB and Thunderbolt driver updates for 6.5-rc1.
Included in here are:
- Lots of USB4/Thunderbolt additions and updates for new hardware
types and fixes as people are starting to get access to the hardware
in the wild
- new gadget controller driver, cdns2, added
- new typec drivers added
- xhci driver updates
- typec driver updates
- usbip driver fixes
- usb-serial driver updates and fixes
- lots of smaller USB driver updates
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZKKcVw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynEIQCgzJgnMCB81mirXlY1ZpCSDFqN8KIAnjRc27/1
vnUzldMQGY/FiS549gD9
=G3yz
-----END PGP SIGNATURE-----
Merge tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for 6.5-rc1.
Included in here are:
- Lots of USB4/Thunderbolt additions and updates for new hardware
types and fixes as people are starting to get access to the
hardware in the wild
- new gadget controller driver, cdns2, added
- new typec drivers added
- xhci driver updates
- typec driver updates
- usbip driver fixes
- usb-serial driver updates and fixes
- lots of smaller USB driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: host: xhci-plat: Set XHCI_STATE_REMOVING before resuming XHCI HC
usb: host: xhci: Do not re-initialize the XHCI HC if being removed
usb: typec: nb7vpq904m: fix CONFIG_DRM dependency
usbip: usbip_host: Replace strlcpy with strscpy
usb: dwc3: gadget: Propagate core init errors to UDC during pullup
USB: serial: option: add LARA-R6 01B PIDs
usb: ulpi: Make container_of() no-op in to_ulpi_dev()
usb: gadget: legacy: fix error return code in gfs_bind
usb: typec: fsa4480: add support for Audio Accessory Mode
usb: typec: fsa4480: rework mux & switch setup to handle more states
usb: typec: ucsi: call typec_set_mode on non-altmode partner change
USB: gadget: f_hid: make hidg_class a static const structure
USB: gadget: f_printer: make usb_gadget_class a static const structure
USB: mon: make mon_bin_class a static const structure
USB: gadget: udc: core: make udc_class a static const structure
USB: roles: make role_class a static const structure
dt-bindings: usb: dwc3: Add interrupt-names property support for wakeup interrupt
dt-bindings: usb: Add StarFive JH7110 USB controller
dt-bindings: usb: dwc3: Add IPQ9574 compatible
usb: cdns2: Fix spelling mistake in a trace message "Wakupe" -> "Wakeup"
...
These are mostly minor cleanups and bugfixes that address harmless
problems.
The largest branch is a conversion of the omap platform
to use GPIO descriptors throughout the tree, for any devices that
are not fully converted to devicetree.
The Samsung Exynos platform gains back support for the Exynos4212
chip that was previously unused and removed but is now used for
the Samsung Galaxy Tab3.
-----BEGIN PGP SIGNATURE-----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=z6FU
-----END PGP SIGNATURE-----
Merge tag 'soc-arm-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"These are mostly minor cleanups and bugfixes that address harmless
problems.
The largest branch is a conversion of the omap platform to use GPIO
descriptors throughout the tree, for any devices that are not fully
converted to devicetree.
The Samsung Exynos platform gains back support for the Exynos4212 chip
that was previously unused and removed but is now used for the Samsung
Galaxy Tab3"
* tag 'soc-arm-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
ARM: omap2: Fix copy/paste bug
MAINTAINERS: Replace my email address
Input: ads7846 - fix pointer cast warning
Input: ads7846 - Fix usage of match data
ARM: omap2: Fix checkpatch issues
arm: omap1: replace printk() with pr_err macro
ARM: omap: Fix checkpatch issues
ARM: s3c: Switch i2c drivers back to use .probe()
ARM: versatile: mark mmc_status() static
ARM: spear: include "pl080.h" for pl080_get_signal() prototype
ARM: sa1100: address missing prototype warnings
ARM: pxa: fix missing-prototypes warnings
ARM: orion5x: fix d2net gpio initialization
ARM: omap2: fix missing tick_broadcast() prototype
ARM: omap1: add missing include
ARM: lpc32xx: add missing include
ARM: imx: add missing include
ARM: highbank: add missing include
ARM: ep93xx: fix missing-prototype warnings
ARM: davinci: fix davinci_cpufreq_init() declaration
...
Now that the driver core allows for struct class to be in read-only
memory, move the hidg_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at load time.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230620094412.508580-11-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, move the usb_gadget_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at load time.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230620094412.508580-10-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, move the udc_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at load time.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230620094412.508580-8-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_udc_connect_control(), soft_connect_store() and
usb_gadget_deactivate() can potentially race against each other to invoke
usb_gadget_connect()/usb_gadget_disconnect(). To prevent this, guard
udc->started, gadget->allow_connect, gadget->deactivate and
gadget->connect with connect_lock so that ->pullup() is only invoked when
the gadget is bound, started and not deactivated. The routines
usb_gadget_connect_locked(), usb_gadget_disconnect_locked(),
usb_udc_connect_control_locked(), usb_gadget_udc_start_locked(),
usb_gadget_udc_stop_locked() are called with this lock held.
An earlier version of this commit was reverted due to the crash reported in
https://lore.kernel.org/all/ZF4BvgsOyoKxdPFF@francesco-nb.int.toradex.com/.
commit 16737e78d190 ("usb: gadget: udc: core: Offload usb_udc_vbus_handler processing")
addresses the crash reported.
Cc: stable@vger.kernel.org
Fixes: 628ef0d273 ("usb: udc: add usb_udc_vbus_handler")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Message-ID: <20230609010227.978661-2-badhri@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_udc_vbus_handler() can be invoked from interrupt context by irq
handlers of the gadget drivers, however, usb_udc_connect_control() has
to run in non-atomic context due to the following:
a. Some of the gadget driver implementations expect the ->pullup
callback to be invoked in non-atomic context.
b. usb_gadget_disconnect() acquires udc_lock which is a mutex.
Hence offload invocation of usb_udc_connect_control()
to workqueue.
UDC should not be pulled up unless gadget driver is bound. The new flag
"allow_connect" is now set by gadget_bind_driver() and cleared by
gadget_unbind_driver(). This prevents work item to pull up the gadget
even if queued when the gadget driver is already unbound.
Cc: stable@vger.kernel.org
Fixes: 1016fc0c09 ("USB: gadget: Fix obscure lockdep violation for udc_mutex")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Message-ID: <20230609010227.978661-1-badhri@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch adds the series of tracepoints that can be used for
debugging issues detected in driver.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Message-ID: <20230602102644.77470-4-pawell@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces the main part of Cadence USBHS driver
to Linux kernel.
To reduce the patch size a little bit, the header file gadget.h was
intentionally added as separate patch.
The Cadence USB 2.0 Controller is a highly configurable IP Core which
supports both full and high speed data transfer.
The current driver has been validated with FPGA platform. We have
support for PCIe bus, which is used on FPGA prototyping.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Message-ID: <20230602102644.77470-3-pawell@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fsg_lun_is_open() test can be eliminated and the code merged with
the preceding conditional, because the LUN won't be open if
cfg->filename wasn't set. Similarly, the error_lun label will never be
reached with an open lun (non-null filp) so remove the unnecessary
fsg_lun_close() call.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Message-ID: <20230607215401.22563-1-ddiss@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch elaborates on some of the edge cases handled by
video_pump around setting no_interrupt flag, and brings the
code style in line with rest of the file.
Link: https://lore.kernel.org/20230602151916.GH26944@pendragon.ideasonboard.com/
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Message-ID: <20230602220455.313801-1-arakesh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add an identifier in the read_fn function declaration because based on
commit ca0d8929e7 ("checkpatch: add warning for unnamed function
definition arguments") it is the preferred coding style even C standard
allows both formats.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Message-ID: <20230607072959.2334046-1-piyush.mehta@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If gs_close has cleared port->port.tty and gs_start_io is called
afterwards, then the function tty_wakeup will attempt to access the value
of the pointer port->port.tty which will cause a null pointer
dereference error.
To avoid this, add a null pointer check to gs_start_io before attempting
to access the value of the pointer port->port.tty.
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Message-ID: <20230602070009.1353946-1-khtsai@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently {modprobe, bind} after {rmmod, unbind} results in probe failure.
genirq: Flags mismatch irq 22. 00000004 (85070400.usb3drd) vs. 00000004 (85070400.usb3drd)
renesas_usb3: probe of 85070000.usb3peri failed with error -16
The reason is, it is trying to register an interrupt handler for the same
IRQ twice. The devm_request_irq() was called with the parent device.
So the interrupt handler won't be unregistered when the usb3-peri device
is unbound.
Fix this issue by replacing "parent dev"->"dev" as the irq resource
is managed by this driver.
Fixes: 9cad72dfc5 ("usb: gadget: Add support for RZ/V2M USB3DRD driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Message-ID: <20230530161720.179927-1-biju.das.jz@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "udc" pointer was never set in the probe() function so it will
lead to a NULL dereference in udc_pci_remove() when we do:
usb_del_gadget_udc(&udc->gadget);
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/ZG+A/dNpFWAlCChk@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While exercising the unbind path, with the current implementation
the functionfs_unbind would be calling which waits for the ffs->mutex
to be available, however within the same time ffs_ep0_read is invoked
& if no setup packets are pending, it will invoke function
wait_event_interruptible_exclusive_locked_irq which by definition waits
for the ev.count to be increased inside the same mutex for which
functionfs_unbind is waiting.
This creates deadlock situation because the functionfs_unbind won't
get the lock until ev.count is increased which can only happen if
the caller ffs_func_unbind can proceed further.
Following is the illustration:
CPU1 CPU2
ffs_func_unbind() ffs_ep0_read()
mutex_lock(ffs->mutex)
wait_event(ffs->ev.count)
functionfs_unbind()
mutex_lock(ffs->mutex)
mutex_unlock(ffs->mutex)
ffs_event_add()
<deadlock>
Fix this by moving the event unbind before functionfs_unbind
to ensure the ev.count is incrased properly.
Fixes: 6a19da1110 ("usb: gadget: f_fs: Prevent race during ffs_ep0_queue_wait")
Cc: stable <stable@kernel.org>
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20230525092854.7992-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ISOC transfers expect a certain cadence of requests being queued. Not
keeping up with the expected rate of requests results in missed ISOC
transfers (EXDEV). The application layer may or may not produce video
frames to match this expectation, so uvc gadget driver must handle cases
where the application is not queuing up buffers fast enough to fulfill
ISOC requirements.
Currently, uvc gadget driver waits for new video buffer to become available
before queuing up usb requests. With this patch the gadget driver queues up
0 length usb requests whenever there are no video buffers available. The
USB controller's complete callback is used as the limiter for how quickly
the 0 length packets will be queued. Video buffers are still queued as
soon as they become available.
Link: https://lore.kernel.org/CAMHf4WKbi6KBPQztj9FA4kPvESc1fVKrC8G73-cs6tTeQby9=w@mail.gmail.com/
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20230508231103.1621375-1-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When serial console over USB is enabled, gs_console_connect
queues gs_console_work, where it acquires the spinlock and
queues the usb request, and this request goes to gadget layer.
Now consider a situation where gadget layer prints something
to dmesg, this will eventually call gs_console_write() which
requires cons->lock. And this causes spinlock recursion. Avoid
this by excluding usb_ep_queue from the spinlock.
spin_lock_irqsave //needs cons->lock
gs_console_write
.
.
_printk
__warn_printk
dev_warn/pr_err
.
.
[USB Gadget Layer]
.
.
usb_ep_queue
gs_console_work
__gs_console_push // acquires cons->lock
process_one_work
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/1683638872-6885-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consider a case where gserial_disconnect has already cleared
gser->ioport. And if gserial_suspend gets called afterwards,
it will lead to accessing of gser->ioport and thus causing
null pointer dereference.
Avoid this by adding a null pointer check. Added a static
spinlock to prevent gser->ioport from becoming null after
the newly added null pointer check.
Fixes: aba3a8d01d ("usb: gadget: u_serial: add suspend resume callbacks")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/1683278317-11774-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here and this resolves merge conflicts in:
drivers/usb/dwc3/gadget.c
drivers/usb/gadget/udc/core.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-45-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-44-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-43-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230517230239.187727-42-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230517230239.187727-41-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20230517230239.187727-40-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20230517230239.187727-39-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-38-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-37-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-36-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-35-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-34-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20230517230239.187727-33-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-32-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-31-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-30-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230517230239.187727-29-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-28-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230517230239.187727-27-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-26-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-25-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PXA platform has a number of configurations that end up with
a warning like these when building with W=1:
drivers/hwmon/max1111.c:83:5: error: no previous prototype for 'max1111_read_channel' [-Werror=missing-prototypes]
arch/arm/mach-pxa/reset.c:86:6: error: no previous prototype for 'pxa_restart' [-Werror=missing-prototypes]
arch/arm/mach-pxa/mfp-pxa2xx.c:254:5: error: no previous prototype for 'keypad_set_wake' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa25x.c:70:14: error: no previous prototype for 'pxa25x_get_clk_frequency_khz' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa25x.c:325:12: error: no previous prototype for 'pxa25x_clocks_init' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa27x.c:74:14: error: no previous prototype for 'pxa27x_get_clk_frequency_khz' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa27x.c:102:6: error: no previous prototype for 'pxa27x_is_ppll_disabled' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa27x.c:470:12: error: no previous prototype for 'pxa27x_clocks_init' [-Werror=missing-prototypes]
arch/arm/mach-pxa/pxa27x.c:44:6: error: no previous prototype for 'pxa27x_clear_otgph' [-Werror=missing-prototypes]
arch/arm/mach-pxa/pxa27x.c:58:6: error: no previous prototype for 'pxa27x_configure_ac97reset' [-Werror=missing-prototypes]
arch/arm/mach-pxa/spitz_pm.c:170:15: error: no previous prototype for 'spitzpm_read_devdata' [-Werror=missing-prototypes]
The problem is that there is a declaration for each of these, but
it's only seen by the caller and not the callee. Moving these
into appropriate header files ensures that both use the same
calling conventions and it avoids the warnings.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230516153109.514251-11-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In the event, gadget_connect call (which invokes pullup) fails,
propagate the error to udc bind operation which inturn sends the
error to configfs. The userspace can then retry enumeartion if
it chooses to.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230510075252.31023-3-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CDC-ECM specification [1] requires to send the host MAC address as
an uppercase hexadecimal string in chapter "5.4 Ethernet Networking
Functional Descriptor":
The Unicode character is chosen from the set of values 30h through
39h and 41h through 46h (0-9 and A-F).
However, snprintf(.., "%pm", ..) generates a lowercase MAC address
string. While most host drivers are tolerant to this, UsbNcm.sys on
Windows 10 is not. Instead it uses a different MAC address with all
bytes set to zero including and after the first byte containing a
lowercase letter. On Windows 11 Microsoft fixed it, but apparently they
did not backport the fix.
This change fixes the issue by upper-casing the MAC to comply with the
specification.
[1]: https://www.usb.org/document-library/class-definitions-communication-devices-12, file ECM120.pdf
Fixes: bcd4a1c40b ("usb: gadget: u_ether: construct with default values and add setters/getters")
Cc: stable@vger.kernel.org
Signed-off-by: Konrad Gräfe <k.graefe@gateware.de>
Link: https://lore.kernel.org/r/20230505143640.443014-1-k.graefe@gateware.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
Here is the large set of USB and Thunderbolt changes for 6.4-rc1.
"biggest" thing in here is the removal of two obsolete drivers, u132-hcd
and ftdi-elan, making this a net-removal of code overall.
Other than the driver removals, included in here are:
- Thunderbolt updates for new hardware and features
- xhci driver updates and fixes
- dwc3 driver updates and fixes
- gadget core and driver updates and features added
- mtu3 driver updates
- dwc2 driver fixes and updates
- usb-serial driver updates
- typec driver updates and fixes
- platform remove callback changes
- dts updates and conversions
- other small changes
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEqC+g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynP6QCg0MnpRjOSFyAB0t9LWFng4rRikj4AoIpxvs2T
GbU7NdPHU3fddq0KB+Nd
=M+Ib
-----END PGP SIGNATURE-----
Merge tag 'usb-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the large set of USB and Thunderbolt changes for 6.4-rc1.
The "biggest" thing in here is the removal of two obsolete drivers,
u132-hcd and ftdi-elan, making this a net-removal of code overall.
Other than the driver removals, included in here are:
- Thunderbolt updates for new hardware and features
- xhci driver updates and fixes
- dwc3 driver updates and fixes
- gadget core and driver updates and features added
- mtu3 driver updates
- dwc2 driver fixes and updates
- usb-serial driver updates
- typec driver updates and fixes
- platform remove callback changes
- dts updates and conversions
- other small changes
All have been in linux-next for a while with no reported problems"
* tag 'usb-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (177 commits)
usb: dwc3: gadget: Refactor EP0 forced stall/restart into a separate API
usb: dwc3: gadget: Execute gadget stop after halting the controller
media: radio-shark: Add endpoint checks
USB: sisusbvga: Add endpoint checks
USB: core: Add routines for endpoint checks in old drivers
usb: dwc3: gadget: Stall and restart EP0 if host is unresponsive
dt-bindings: usb: snps,dwc3: Add 'snps,parkmode-disable-hs-quirk' quirk
usb: dwc3: core: add support for disabling High-speed park mode
dt-bindings: usb: ci-hdrc-usb2: allow multiple PHYs
usb: mtu3: add optional clock xhci_ck and frmcnt_ck
dt-bindings: usb: mtu3: add two optional clocks
usb: mtu3: expose role-switch control to userspace
usb: mtu3: unlock @mtu->lock just before giving back request
usb: mtu3: fix kernel panic at qmu transfer done irq handler
usb: mtu3: use boolean return value
usb: mtu3: give back request when rx error happens
usb: chipidea: fix missing goto in `ci_hdrc_probe`
usb: gadget: udc: core: Prevent redundant calls to pullup
usb: gadget: udc: core: Invoke usb_gadget_connect only when started
usb: typec: ucsi: don't print PPM init deferred errors
...
Updates to the usual drivers (megaraid_sas, scsi_debug, lpfc, target,
mpi3mr, hisi_sas, arcmsr). The major core change is the
constification of the host templates (which touches everything) along
with other minor fixups and clean ups.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZEmJACYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishU4FAP0WYhFC
rkbY203/+ErUuwvOKum0VwJKUowCaUD0MBwScAD+Ok/NWobmjdXUBbPUbvVkr+hE
8B/xs9hodX+1fVJcVG0=
=fS/j
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (megaraid_sas, scsi_debug, lpfc, target,
mpi3mr, hisi_sas, arcmsr).
The major core change is the constification of the host templates
(which touches everything) along with other minor fixups and clean
ups"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (207 commits)
scsi: ufs: mcq: Use pointer arithmetic in ufshcd_send_command()
scsi: ufs: mcq: Annotate ufshcd_inc_sq_tail() appropriately
scsi: cxlflash: s/semahpore/semaphore/
scsi: lpfc: Silence an incorrect device output
scsi: mpi3mr: Use IRQ save variants of spinlock to protect chain frame allocation
scsi: scsi_debug: Fix missing error code in scsi_debug_init()
scsi: hisi_sas: Work around build failure in suspend function
scsi: lpfc: Fix ioremap issues in lpfc_sli4_pci_mem_setup()
scsi: mpt3sas: Fix an issue when driver is being removed
scsi: mpt3sas: Remove HBA BIOS version in the kernel log
scsi: target: core: Fix invalid memory access
scsi: scsi_debug: Drop sdebug_queue
scsi: scsi_debug: Only allow sdebug_max_queue be modified when no shosts
scsi: scsi_debug: Use scsi_host_busy() in delay_store() and ndelay_store()
scsi: scsi_debug: Use blk_mq_tagset_busy_iter() in stop_all_queued()
scsi: scsi_debug: Use blk_mq_tagset_busy_iter() in sdebug_blk_mq_poll()
scsi: scsi_debug: Dynamically allocate sdebug_queued_cmd
scsi: scsi_debug: Use scsi_block_requests() to block queues
scsi: scsi_debug: Protect block_unblock_all_queues() with mutex
scsi: scsi_debug: Change shost list lock to a mutex
...
usb_gadget_connect calls gadget->ops->pullup without checking whether
gadget->connected was previously set. Make this symmetric to
usb_gadget_disconnect by returning early if gadget->connected is
already set.
Fixes: 5a1da544e5 ("usb: gadget: core: do not try to disconnect gadget if it is not connected")
Cc: stable@vger.kernel.org
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20230407030741.3163220-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_udc_connect_control does not check to see if the udc has already
been started. This causes gadget->ops->pullup to be called through
usb_gadget_connect when invoked from usb_udc_vbus_handler even before
usb_gadget_udc_start is called. Guard this by checking for udc->started
in usb_udc_connect_control before invoking usb_gadget_connect.
Guarding udc->vbus, udc->started, gadget->connect, gadget->deactivate
related functions with connect_lock. usb_gadget_connect_locked,
usb_gadget_disconnect_locked, usb_udc_connect_control_locked,
usb_gadget_udc_start_locked, usb_gadget_udc_stop_locked are called with
this lock held as they can be simulataneously invoked from different code
paths.
Adding an additional check to make sure udc is started(udc->started)
before pullup callback is invoked.
Fixes: 628ef0d273 ("usb: udc: add usb_udc_vbus_handler")
Cc: stable@vger.kernel.org
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20230407030741.3163220-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several USB drivers use of_platform_* functions which are declared in
of_platform.h. of_platform.h gets implicitly included by of_device.h,
but that is going to be removed soon. Nothing else depends on of_device.h
so it can be dropped.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230410232639.1561152-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'ret' variable in the function tegra_xudc_gadget_vbus_draw() is not
needed and so remove this variable.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230405181854.42355-2-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ac82b56bda ("usb: gadget: tegra-xudc: Add vbus_draw support")
populated the vbus_draw callback for the Tegra XUDC driver. The function
tegra_xudc_gadget_vbus_draw(), that was added by this commit, assumes
that the pointer 'curr_usbphy' has been initialised, which is not always
the case because this is only initialised when the USB role is updated.
Fix this crash, by checking that the 'curr_usbphy' is valid before
dereferencing.
Fixes: ac82b56bda ("usb: gadget: tegra-xudc: Add vbus_draw support")
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230405181854.42355-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here for testing, and this resolves two merge
conflicts, one pointed out by linux-next:
drivers/usb/dwc3/dwc3-pci.c
drivers/usb/host/xhci-pci.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iov_iter for ep_read_iter can be ITER_UBUF with io_uring.
In that case dup_iter() does not have to allocate iov and it can
return NULL. Fix the assumption by checking for iter_is_ubuf()
other wise ep_read_iter can treat this as failure and return -ENOMEM.
Fixes: 1e23db450c ("io_uring: use iter_ubuf for single range imports")
Signed-off-by: Sandeep Dhavale <dhavale@google.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/20230401060509.3608259-3-dhavale@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iov_iter for ffs_epfile_read_iter can be ITER_UBUF with io_uring.
In that case dup_iter() does not have to allocate anything and it
can return NULL. ffs_epfile_read_iter treats this as a failure and
returns -ENOMEM. Fix it by checking if iter_is_ubuf().
Fixes: 1e23db450c ("io_uring: use iter_ubuf for single range imports")
Signed-off-by: Sandeep Dhavale <dhavale@google.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/20230401060509.3608259-2-dhavale@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When host sends suspend notification to the device, handle
the suspend callbacks in the function driver. Depending on
the remote wakeup capability the device can either trigger a
remote wakeup or wait for the host initiated resume to resume
data transfer.
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1679694482-16430-7-git-send-email-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When host sends function suspend feature selector to the device,
inspect the received packet and trigger function suspend or
function resume accordingly. Inspect the remote wakeup bit and
arm the function for remote wakeup if it is wakeup capable. Also
host queries the function wakeup capability through a get status
request before sending function resume. Handle such requests in
composite layer.
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1679694482-16430-6-git-send-email-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3.2 spec section 9.2.5.4 quotes that a function may signal that
it wants to exit from Function Suspend by sending a Function
Wake Notification to the host if it is enabled for function
remote wakeup. Add an api in composite layer that can be used
by the function drivers to support this feature. Also expose
a gadget op so that composite layer can trigger a wakeup request
to the UDC driver.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Link: https://lore.kernel.org/r/1679694482-16430-4-git-send-email-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wakeup bit in the bmAttributes field indicates whether the device
is configured for remote wakeup. But this field should be allowed to
set only if the UDC supports such wakeup mechanism. So configure this
field based on UDC capability. Also inform the UDC whether the device
is configured for remote wakeup by implementing a gadget op.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Link: https://lore.kernel.org/r/1679694482-16430-2-git-send-email-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the Processing Unit and Camera Terminal descriptors defined in
the UVC Gadget we currently hard-code values into their bmControls
fields, which enumerates which controls the gadget is able to
support. This isn't appropriate since only the userspace companion
program to the kernel driver will know which controls are supported.
Make the configfs attributes that point to those fields read/write
so userspace can set them to appropriate values.
Document the new behaviour at the same time so the functionality is
clear.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230309105825.216745-1-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes here, and the USB gadget update for future
development patches to be based on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Christie <michael.christie@oracle.com> says:
The following patches apply over Martin's 6.4 branches and Linus's tree.
They fix a couple regressions in iscsit that occur when there are TMRs
executing and a connection is closed. It also includes Dimitry's fixes in
related code paths for cmd cleanup when ERL2 is used and the write pending
hang during conn cleanup.
This version of the patchset brings it back to just regressions and fixes
for bugs we have a lot of users hitting. I'm going to fix isert and get it
hooked into iscsit properly in a second patchset, because this one was
getting so large. I've also moved my cleanup type of patches for a 3rd
patchset.
Link: https://lore.kernel.org/r/20230319015620.96006-1-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow target_get_sess_cmd() users to pass in the cmd counter they want to
use. Right now we pass in the session's cmd counter but in a subsequent
commit iSCSI will switch from per session to per conn.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230319015620.96006-4-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In renesas_usb3_probe, role_work is bound with renesas_usb3_role_work.
renesas_usb3_start will be called to start the work.
If we remove the driver which will call usbhs_remove, there may be
an unfinished work. The possible sequence is as follows:
CPU0 CPU1
renesas_usb3_role_work
renesas_usb3_remove
usb_role_switch_unregister
device_unregister
kfree(sw)
//free usb3->role_sw
usb_role_switch_set_role
//use usb3->role_sw
The usb3->role_sw could be freed under such circumstance and then
used in usb_role_switch_set_role.
This bug was found by static analysis. And note that removing a
driver is a root-only operation, and should never happen in normal
case. But the root user may directly remove the device which
will also trigger the remove function.
Fix it by canceling the work before cleanup in the renesas_usb3_remove.
Fixes: 39facfa01c ("usb: gadget: udc: renesas_usb3: Add register of usb role switch")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20230320062931.505170-1-zyytlz.wz@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clang with W=1 reports
drivers/usb/gadget/udc/renesas_usbf.c:548:20: error: unused function
'usbf_ep_dma_reg_clrset' [-Werror,-Wunused-function]
static inline void usbf_ep_dma_reg_clrset(struct usbf_ep *ep, uint offset,
^
This function is not used, so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230319155910.1706294-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core can properly handle constant struct bus_type,
move all of the USB subsystem struct bus_type structures as const,
placing them into read-only memory which can not be modified at runtime.
Cc: Johan Hovold <johan@kernel.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230313182918.1312597-36-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove callouts that are identical to the default implementations in TCM
Core.
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Link: https://lore.kernel.org/r/20230313181110.20566-8-d.bogdanov@yadro.com
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It looks like the driver copied'n'pasted almost random set of
headers for its code. Rectify it a bit by removing of_gpio.h
that is not only unused, but also will be removed in the future
completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230313155310.80022-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/usb/gadget/udc/max3420_udc.c:1312:34: error: ‘max3420_udc_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230311173624.263189-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/usb/gadget/udc/renesas_usb3.c:2811:34: error: ‘usb3_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230311173624.263189-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/usb/gadget/udc/rzv2m_usb3drd.c:120:34: error: ‘rzv2m_usb3drd_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230311173624.263189-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144728.1545786-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the USB gadget framework supports only version 1.0 of the MS OS
descriptor. OS desc has a field bcdVersion indicating its version, with
v1.0 represented by the value 0x100. However, __ffs_do_os_desc_header()
was expecting the incorrect value 0x1, so allow the correct value 0x100.
The bcdVersion field of the descriptor that is actually sent to the host
is set by composite_setup() (in composite.c) to the fixed value 0x100.
Therefore, it can be understood that __ffs_do_os_desc_header() is only
performing a format check of the OS desc passed to functionfs. If a value
other than 0x100 is accepted, there is no effect on communication over
the USB bus. Indeed, until now __ffs_do_os_desc_header() has only accepted
the incorrect value 0x1, but there was no problem with the communication
over the USB bus.
However, this can be confusing for functionfs userspace drivers. Since
bcdVersion=0x100 is used in actual communication, functionfs should accept
the value 0x100.
Note that the correct value for bcdVersion in OS desc v1.0 is 0x100, but
to avoid breaking old userspace drivers, the value 0x1 is also accepted as
an exception. At this time, a message is output to notify the user to fix
the userspace driver.
Signed-off-by: Yuta Hayama <hayama@lineo.co.jp>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Link: https://lore.kernel.org/r/290f96db-1877-5137-373a-318e7b4f2dde@lineo.co.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
