DWC_usb32 v1.00a and later can use SET_EP_PRIME command to reinitiate a
stream. Use the command to handle NoStream rejection instead of ending
and restarting the endpoint.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Overview of stream transfer requirement:
* A transfer will have a set of TRBs of the same stream ID.
* A transfer is started with a stream ID in START_TRANSFER command.
* A new stream will only start when the previous completes.
Overview of stream events:
* A "prime" from host indicates that its endpoints are active
(buffers prepared and ready to receive/transmit data). The controller
automatically initiates stream if it sees this.
* A "NoStream" rejection event indicates that the host isn't ready.
Host will put the endpoint back to idle state. Device may need to
reinitiate the stream to start transfer again.
* A Stream Found event means host accepted device initiated stream.
Nothing needs to be done from driver.
To initiate a stream, the driver will issue START_TRANSFER command with
a stream ID. To reinitiate the stream, the driver must issue
END_TRANSFER and restart the transfer with START_TRANSFER command with
the same stream ID.
This implementation handles device-initated streams (e.g. UASP driver).
It also handles some hosts' quirky behavior where they only prime each
endpoint once.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Don't prepare TRBs beyond a transfer. In DWC_usb32, its transfer burst
capability may try to read and use TRBs beyond the active transfer. For
other controllers, they don't process the next transfer TRBs until the
current transfer is completed. Explicitly prevent preparing TRBs ahead
for all controllers.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If a transfer is in-progress, any new request should not kick off
another transfer. The driver needs to wait for the current transfer to
complete before starting off the next transfer. Introduce a new flag
DWC3_EP_WAIT_TRANSFER_COMPLETE for this.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In DWC3, to prepare TRBs for streams, all the TRBs of a transfer will
use the same stream ID. To start a new stream, the driver needs to wait
for the current transfer to complete or ended (by END_TRANFER command).
As a result, inform the controller of the last TRB of a transfer so that
it knows when a transfer completes and start a new transfer of a new
stream.
Even though the transfer completion handling can be applied for other
non-isoc endpoints, only do it for streams due to its requirement.
It's better to keep the controller's TRB cache full than waiting for
transfer completion and starting a new transfer.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
To switch from one stream to another, this requires the driver to start
a new transfer with a specific stream ID. For a transfer to complete,
the driver needs to indicate the last TRB of a transfer, and it needs to
enable XferComplete event to handle completed TRBs of a transfer. Let's
enable this event only for stream capable endpoints.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
To prepare for handling of XferComplete event, let's refactor and split
up dwc3_gadget_endpoint_transfer_in_progress() to handle TRBs completion
for different events. The handling of TRBs completion will be the same,
but the status of XferComplete event is different than XferInProgress.
No functional change in this commit.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
While handling TRBs completion, if a END_TRANSFER command isn't
completed, don't kick new transfer or issue END_TRANSFER command.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
DWC_usb32 supports MDWIDTH value larger than 255 and up to 1023. The
field HWPARAMS6[9:8] stores the upper 2-bit values of the DWC_usb32's
MDWIDTH. Check that parameter and properly get the MDWIDTH for
DWC_usb32.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Synopsys introduces a new controller DWC_usb32. It supports dual-lane
and speed up to 20 Gbps, and the DWC3 driver will drive this controller.
Currently the driver uses a single field dwc->revision to ID both
DWC_usb3 and DWC_usb31 and their version number. This was sufficient for
two IPs, but this method doesn't work with additional IPs. As a result,
let's separate the dwc->revision field to 2 separate fields: ip and
revision. The ip field now stores the ID of the controller's IP while
the revision field stores the controller's version number.
This new scheme enforces DWC3 to compare the revision within the same IP
only. As a result, we must update all the revision check of the
controller to check its corresponding IP.
To help with this enforcement, we create a few macros to help with
the common version checks:
DWC3_IP_IS(IP)
DWC3_VER_IS(IP, VERSION)
DWC3_VER_IS_PRIOR(IP, VERSION)
DWC3_VER_IS_WITHIN(IP, LOWER_VERSION, UPPER_VERSION)
DWC3_VER_TYPE_IS_WITHIN(IP, VERSION,
LOWER_VERSION_TYPE,
UPPER_VERSION_TYPE)
The DWC_usb32 controller operates using the same programming model and
with very similar configurations as its previous controllers. Please
note that the various IP and revision checks in this patch match the
current checks for DWC_usb31 version 1.90a. Additional configurations
that are unique to DWC_usb32 are applied separately.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/dwc3/drd.c:85:3-24: WARNING: Assignment of 0/1 to bool
variable
drivers/usb/dwc3/drd.c:59:2-23: WARNING: Assignment of 0/1 to bool
variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There is now a dedicated driver for these SoCs making the old compatible
obsolete.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In order to add support for the Amlogic GXL/GXM USB Glue, this adds
the corresponding :
- PHY names
- clock names
- USB2 PHY init and mode set
- regmap setup
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
On the Amlogic GXL/GXM SoCs, the OTG PHY status signals are always
connected to the DWC3 controller, thus crashing the controller when
switching to OTG mode when port is not populated with a device/cable to
Host.
Amlogic added a bit to disconnect the OTG PHY status signals from the DWC3
to be used when switching the OTG PHY as Device to the DWC2 controller.
The drawback is that it makes the DWC3 port state machine stall and needs
a full reset of the DWC3 controller to get connect status to the port
connected to the OTG PHY, but not the other one.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Refactor the USB init code patch to handle the Amlogic GXL/GXM needing
to initialize the OTG port as Peripheral mode for the DWC2 IP to probe
correctly.
A secondary, post_init callback is added to setup the OTG PHY mode after
powering up the PHYs and before probing the DWC2 and DWC3 controllers.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If there are still pending requests because no TRB was available,
prepare more when started requests are completed.
Introduce dwc3_gadget_ep_should_continue() to check for incomplete and
pending requests to resume updating new TRBs to the controller's TRB
cache.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Calling into the role switch API requires that these functions
are loaded, if they are in a loadable module and dwc3 itself
is built-in, this produces a link error:
drivers/usb/dwc3/drd.o: In function `dwc3_usb_role_switch_get':
drd.c:(.text+0x26): undefined reference to `usb_role_switch_get_drvdata'
drivers/usb/dwc3/drd.o: In function `dwc3_usb_role_switch_set':
drd.c:(.text+0x97): undefined reference to `usb_role_switch_get_drvdata'
drivers/usb/dwc3/drd.o: In function `dwc3_drd_init':
drd.c:(.text+0x1ca7): undefined reference to `usb_role_switch_register'
drivers/usb/dwc3/drd.o: In function `dwc3_drd_exit':
drd.c:(.text+0x1e92): undefined reference to `usb_role_switch_unregister'
Select the USB_ROLE_SWITCH symbol from dwc3 in that configuration.
Fixes: 0339f7fbc8 ("usb: dwc3: fix up for role switch API change")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Intel Merrifield provides a DR support via PMIC which has its own
extcon driver.
Add a property string to link to that driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The check for the HWO flag in dwc3_gadget_ep_reclaim_trb_sg()
causes us to break out of the loop before we call
dwc3_gadget_ep_reclaim_completed_trb(), which is what likely
should be clearing the HWO flag.
This can cause odd behavior where we never reclaim all the trbs
in the sg list, so we never call giveback on a usb req, and that
will causes transfer stalls.
This effectively resovles the adb stalls seen on HiKey960
after userland changes started only using AIO in adbd.
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Josh Gao <jmgao@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org #4.20+
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the driver issued START_TRANSFER and received a no-resource status,
then generally there are a few reasons for this:
1) The driver did not allocate resource for the endpoint during
power-on-reset initialization.
2) The transfer resource was reset. At this moment, we don't do this in
the driver, but it occurs when the driver issues START_CONFIG cmd to ep0
with resource index=2.
3) The driver issues the START_TRANSFER command to an already started
endpoint. Usually, this is because the END_TRANSFER command hasn't
completed yet.
Print out a warning to help debug this issue in the driver.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
After a number of unsuccessful start isoc attempts due to bus-expiry
status, issue END_TRANSFER command and retry on the next XferNotReady
event.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
As long as the START_TRANSFER command completes, it provides the
resource index of the endpoint. Use this when we need to issue
END_TRANSFER command to an isoc endpoint to retry with a new
XferNotReady event.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If dwc3 fails to issue START_TRANSFER/UPDATE_TRANSFER command, then we
should properly end an active transfer and give back all the started
requests. However if it's for an isoc endpoint, the failure maybe due to
bus-expiry status. In this case, don't give back the requests and wait
for the next retry.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the driver is configured to use DRD role-switch, let the drd code
path decide the default dr_mode.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the driver is configured to use DRD role-switch, it's not OTG. There
won't be OTG irq to free. Check for dwc->otg_irq before freeing it.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Refactor the USB2 PHY init code patch to handle the Amlogic GXL/GXM
not having the PHY mode control registers in the Glue but in the PHY
registers.
The Amlogic GXL/GXM will call phy_set_mode() instead of programming the
PHY mode control registers, thus add two new callbacks to the SoC match
data.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The dwc3_meson_g12a_usb_init function can return an error, check it.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In order to support the Amlogic GXL/GXM SoCs, the reset line must
be handled as shared since also used by the PHYs.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
On the Amlogic GXL/GXM SoCs, only the USB control registers are available,
the PHY mode being handled in the PHY registers.
Thus, handle the PHY mode registers in separate regmaps and prepare
support for Amlogic GXL/GXM SoCs by moving the regmap setup in a callback
set in the SoC match data.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
To handle the variable USB2 PHY counts on GXL and GXM SoCs, add the
possible PHY names for each SoC in the compatible match data.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hanjie Lin <hanjie.lin@amlogic.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The flow from function dwc3_gadget_ep_dequeue() is not easy to follow.
Refactor it for easier read. No functional change in this commit.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Remove 2 unnecessary checks:
1) A request in the started_list must have its trb field set. So
checking for req->trb is unnecessary.
2) An endpoint must have started (and have not ended) for the request to
still be in the started_list. There's no point to check if the endpoint
is started. We had this check because previously the driver didn't
handle the endpoint's started/ended flags for END_TRANSFER command
properly. See commit 9f45581f5e ("usb: dwc3: gadget: early giveback
if End Transfer already completed").
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If a request is dequeued, the transfer is cancelled. Give back all
the started requests.
In most scenarios, the function driver dequeues all requests of a
transfer when there's a failure. If the function driver follows this,
then it's fine. If not, then we'd be skipping TRBs at different points
within the dequeue and enqueue pointers, making dequeue/enqueue pointers
useless. To enforce and make sure that we're properly skipping TRBs,
cancel all the started requests and give back all the cancelled requests
to the function drivers.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
DWC3 must not issue CLEAR_STALL command to control endpoints. The
controller automatically clears the STALL when it receives the SETUP
token. Also, when the driver receives ClearFeature(halt_ep), DWC3 must
stop any active transfer from the endpoint and give back all the
requests to the function drivers.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The DRD module calls dwc3_set_mode() on role switches, i.e. when a device is
being plugged in. In order to support continuous runtime power management when
plugging in / unplugging a cable, we need to call pm_runtime_get_sync() in
this path.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to DesignWare USB3 DRD Core Support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
A request may not be completed because not all the TRBs are prepared for
it. This happens when we run out of available TRBs. When some TRBs are
completed, the driver needs to prepare the rest of the TRBs for the
request. The check dwc3_gadget_ep_request_completed() shouldn't be
checking the amount of data received but rather the number of pending
TRBs. Revise this request completion check.
Cc: stable@vger.kernel.org
Fixes: e0c42ce590 ("usb: dwc3: gadget: simplify IOC handling")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The controller always supports link recovery for device in SS and SSP.
Remove the speed limit check. Also, when the device is in RESUME or
RESET state, it means the controller received the resume/reset request.
The driver must send the link recovery to acknowledge the request. They
are valid states for the driver to send link recovery.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Fixes: ee5cd41c91 ("usb: dwc3: Update speed checks for SuperSpeedPlus")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Currently the calculation of max packet size limit for IN endpoints is
too restrictive. This prevents a matching of a capable hardware endpoint
during configuration. Below is the minimum recommended HW configuration
to support a particular endpoint setup from the databook:
For OUT endpoints, the databook recommended the minimum RxFIFO size to
be at least 3x MaxPacketSize + 3x setup packets size (8 bytes each) +
clock crossing margin (16 bytes).
For IN endpoints, the databook recommended the minimum TxFIFO size to be
at least 3x MaxPacketSize for endpoints that support burst. If the
endpoint doesn't support burst or when the device is operating in USB
2.0 mode, a minimum TxFIFO size of 2x MaxPacketSize is recommended.
Base on these recommendations, we can calculate the MaxPacketSize limit
of each endpoint. This patch revises the IN endpoint MaxPacketSize limit
and also sets the MaxPacketSize limit for OUT endpoints.
Reference: Databook 3.30a section 3.2.2 and 3.2.3
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Change the macro name DWC3_GTXFIFOSIZ_TXFDEF to DWC3_GTXFIFOSIZ_TXFDEP
to match with the register name GTXFIFOSIZ.TXFDEP.
Fixes: 457e84b662 ("usb: dwc3: gadget: dynamically re-size TxFifos")
Fixes: 0cab8d26d6 ("usb: dwc3: Update DWC_usb31 GTXFIFOSIZ reg fields")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
After merging the usb-gadget tree, today's linux-next build (arm
multi_v7_defconfig) failed like this:
drivers/usb/dwc3/drd.c: In function 'dwc3_setup_role_switch':
drivers/usb/dwc3/drd.c:551:23: error: assignment to 'usb_role_switch_set_t' {aka 'int (*)(struct usb_role_switch *, enum usb_role)'} from incompatible pointer type 'int (*)(struct device *, enum usb_role)' [-Werror=incompatible-pointer-types]
551 | dwc3_role_switch.set = dwc3_usb_role_switch_set;
| ^
drivers/usb/dwc3/drd.c:552:23: error: assignment to 'usb_role_switch_get_t' {aka 'enum usb_role (*)(struct usb_role_switch *)'} from incompatible pointer type 'enum usb_role (*)(struct device *)' [-Werror=incompatible-pointer-types]
552 | dwc3_role_switch.get = dwc3_usb_role_switch_get;
| ^
Caused by commit
8a0a137997 ("usb: dwc3: Registering a role switch in the DRD code.")
interacting with commit
bce3052f0c ("usb: roles: Provide the switch drivers handle to the switch in the API")
from the usb tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20200316143752.473f1073@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lots of changes on dwc3 this time, most of them from Thinh fixing a
bunch of really old mishaps on the driver.
DWC2 got support for STM32MP15 and a couple RockChip SoCs while DWC3
learned about Amlogic A1 family.
Apart from these, we have a few spelling fixes and other minor
non-critical fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----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=L9gx
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.7 merge window
Lots of changes on dwc3 this time, most of them from Thinh fixing a
bunch of really old mishaps on the driver.
DWC2 got support for STM32MP15 and a couple RockChip SoCs while DWC3
learned about Amlogic A1 family.
Apart from these, we have a few spelling fixes and other minor
non-critical fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'usb-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (41 commits)
dt-bindings: usb: add documentation for aspeed usb-vhub
ARM: dts: aspeed-g4: add vhub port and endpoint properties
ARM: dts: aspeed-g5: add vhub port and endpoint properties
ARM: dts: aspeed-g6: add usb functions
usb: gadget: aspeed: add ast2600 vhub support
usb: gadget: aspeed: read vhub properties from device tree
usb: gadget: aspeed: support per-vhub usb descriptors
usb: gadget: f_phonet: Replace zero-length array with flexible-array member
usb: gadget: composite: Inform controller driver of self-powered
usb: gadget: amd5536udc: fix spelling mistake "reserverd" -> "reserved"
udc: s3c-hsudc: Silence warning about supplies during deferred probe
usb: dwc2: Silence warning about supplies during deferred probe
dt-bindings: usb: dwc2: add compatible property for rk3368 usb
dt-bindings: usb: dwc2: add compatible property for rk3328 usb
usb: gadget: add raw-gadget interface
usb: dwc2: Implement set_selfpowered()
usb: dwc3: qcom: Replace <linux/clk-provider.h> by <linux/of_clk.h>
usb: dwc3: core: don't do suspend for device mode if already suspended
usb: dwc3: Rework resets initialization to be more flexible
usb: dwc3: Rework clock initialization to be more flexible
...
The DWC3 USB driver is not a clock provider, and just needs to call
of_clk_get_parent_count().
Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If dwc->dev in device mode already runtime suspended, don't do it again
for system suspend.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The dwc3 core binding specifies one reset.
However some variants of the hardware may have more. Previously
this was handled by using the dwc3-of-simple glue driver, but
that resulted in a proliferation of bindings for for every
variant, when the only difference was the clocks and resets
lists.
So this patch reworks the reading of the resets to fetch all the
resets specified in the dts together.
This patch was recommended by Rob Herring <robh@kernel.org>
as an alternative to creating multiple bindings for each variant
of hardware.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The dwc3 core binding specifies three clocks:
ref, bus_early, and suspend
which are all controlled in the driver together.
However some variants of the hardware my not have all three
clks, or some may have more. Usually this was handled by using
the dwc3-of-simple glue driver, but that resulted in a
proliferation of bindings for for every variant, when the only
difference was the clocks and resets lists.
So this patch reworks the reading of the clks from the dts to
use devm_clk_bulk_get_all() will will fetch all the clocks
specified in the dts together.
This patch was recommended by Rob Herring <robh@kernel.org>
as an alternative to creating multiple bindings for each variant
of hardware.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Support the new role-switch-default-mode binding for configuring
the default role the controller assumes as when the usb role is
USB_ROLE_NONE
This patch was split out from a larger patch originally by
Yu Chen <chenyu56@huawei.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The Type-C drivers use USB role switch API to inform the
system about the negotiated data role, so registering a role
switch in the DRD code in order to support platforms with
USB Type-C connectors.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In certain circumstances, the XHCI SuperSpeed instance in park mode
can fail to recover, thus on Amlogic G12A/G12B/SM1 SoCs when there is high
load on the single XHCI SuperSpeed instance, the controller can crash like:
xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
xhci-hcd xhci-hcd.0.auto: Host halt failed, -110
xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
hub 2-1.1:1.0: hub_ext_port_status failed (err = -22)
xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
usb 2-1.1-port1: cannot reset (err = -22)
Setting the PARKMODE_DISABLE_SS bit in the DWC3_USB3_GUCTL1 mitigates
the issue. The bit is described as :
"When this bit is set to '1' all SS bus instances in park mode are disabled"
Synopsys explains:
The GUCTL1.PARKMODE_DISABLE_SS is only available in
dwc_usb3 controller running in host mode.
This should not be set for other IPs.
This can be disabled by default based on IP, but I recommend to have a
property to enable this feature for devices that need this.
CC: Dongjin Kim <tobetter@gmail.com>
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Reported-by: Tim <elatllat@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When skipping TRBs, we need to account for wrapping around the ring
buffer and not modifying some invalid TRBs. Without this fix, dwc3 won't
be able to check for available TRBs.
Cc: stable <stable@vger.kernel.org>
Fixes: 7746a8dfb3 ("usb: dwc3: gadget: extract dwc3_gadget_ep_skip_trbs()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We track END_TRANSFER command completion. Don't clear transfer
started/ended flag prematurely. Otherwise, we'd run into the problem
with restarting transfer before END_TRANSFER command finishes.
Fixes: 6d8a019614 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The main comment in the file mistakenly marked with kernel doc annotation
which makes the parser unhappy:
.../dwc3/host.c:16: warning: Function parameter or member 'dwc' not described in 'dwc3_host_get_irq'
Drop kernel doc annotation from host.c module.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The ACPI companion of the adapter has to be set for xHCI controller
code to read and attach the ports described in the ACPI table.
Use ACPI_COMPANION_SET macro to set this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Exynos5422 DWC3 module support two clk USBD300 and SCLK_USBD300
so add missing code to enable/disable code and suspend clk, for this
add a new compatible samsung,exynos5420-dwusb3 to help configure
dwc3 code and dwc3 suspend clock. Suspend clock controls the PHY power
change from P0 to P1/P2/P3 during U0 to U1/U2/U3 transition.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Clang warns:
../drivers/usb/dwc3/dwc3-meson-g12a.c:421:6: warning: variable 'ret' is
used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
if (priv->otg_mode == USB_DR_MODE_OTG) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/usb/dwc3/dwc3-meson-g12a.c:455:9: note: uninitialized use
occurs here
return ret;
^~~
../drivers/usb/dwc3/dwc3-meson-g12a.c:421:2: note: remove the 'if' if
its condition is always true
if (priv->otg_mode == USB_DR_MODE_OTG) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/usb/dwc3/dwc3-meson-g12a.c:415:9: note: initialize the
variable 'ret' to silence this warning
int ret, irq;
^
= 0
1 warning generated.
It is not wrong, ret is only used when that if statement is true. Just
directly return 0 at the end to avoid this.
Fixes: 729149c53f04 ("usb: dwc3: Add Amlogic A1 DWC3 glue")
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://groups.google.com/d/msg/clang-built-linux/w5iBENco_m4/PPuXreAxBQAJ
Link: https://github.com/ClangBuiltLinux/linux/issues/869
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Adds support for Amlogic A1 USB Control Glue HW.
The Amlogic A1 SoC Family embeds 1 USB Controllers:
- a DWC3 IP configured as Host for USB2 and USB3
A glue connects the controllers to the USB2 PHY of A1 SoC.
Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
By printing enqueue/dequeue pointers, we can make sure that our TRB
handling is correct. We've had a recent situation where we were not
always dequeueing all TRBs in an SG list and this helped figure out
what the problem was.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The USB role callback functions had a parameter pointing to
the parent device (struct device) of the switch. The
assumption was that the switch parent is always the
controller. Firstly, that may not be true in every case, and
secondly, it prevents us from supporting devices that supply
multiple muxes.
Changing the first parameter of usb_role_switch_set_t and
usb_role_switch_get_t from struct device to struct
usb_role_switch.
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If scatter-gather operation is allowed, a large USB request is split
into multiple TRBs. For preparing TRBs for sg list, driver iterates
over the list and creates TRB for each sg and mark the chain bit to
false for the last sg. The current IOMMU driver is clubbing the list
of sgs which shares a page boundary into one and giving it to USB driver.
With this the number of sgs mapped it not equal to the the number of sgs
passed. Because of this USB driver is not marking the chain bit to false
since it couldn't iterate to the last sg. This patch addresses this issue
by marking the chain bit to false if it is the last mapped sg.
At a practical level, this patch resolves USB transfer stalls
seen with adb on dwc3 based db845c, pixel3 and other qcom
hardware after functionfs gadget added scatter-gather support
around v4.20.
Credit also to Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
who implemented a very similar fix to this issue.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org> #4.20+
Signed-off-by: Pratham Pratap <prathampratap@codeaurora.org>
[jstultz: Slight tweak to remove sg_is_last() usage, reworked
commit message, minor comment tweak]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200302214443.55783-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3 USB driver is not a clock provider, and just needs to call
of_clk_get_parent_count().
Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200212101853.9349-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the string formatting is mixing up the offset of ret and
len. Re-work the code to use just len, remove ret and use scnprintf
instead of snprintf and len position accumulation where required.
Remove the -ve return check since scnprintf never returns a failure
-ve size. Also break overly long lines to clean up checkpatch
warnings.
Addresses-Coverity: ("Unused value")
Fixes: 1381a5113c ("usb: dwc3: debug: purge usage of strcat")
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The current code in dwc3_gadget_ep_reclaim_completed_trb() will
check for IOC/LST bit in the event->status and returns if
IOC/LST bit is set. This logic doesn't work if multiple TRBs
are queued per request and the IOC/LST bit is set on the last
TRB of that request.
Consider an example where a queued request has multiple queued
TRBs and IOC/LST bit is set only for the last TRB. In this case,
the core generates XferComplete/XferInProgress events only for
the last TRB (since IOC/LST are set only for the last TRB). As
per the logic in dwc3_gadget_ep_reclaim_completed_trb()
event->status is checked for IOC/LST bit and returns on the
first TRB. This leaves the remaining TRBs left unhandled.
Similarly, if the gadget function enqueues an unaligned request
with sglist already in it, it should fail the same way, since we
will append another TRB to something that already uses more than
one TRB.
To aviod this, this patch changes the code to check for IOC/LST
bits in TRB->ctrl instead.
At a practical level, this patch resolves USB transfer stalls seen
with adb on dwc3 based HiKey960 after functionfs gadget added
scatter-gather support around v4.20.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org>
Tested-by: Tejas Joglekar <tejas.joglekar@synopsys.com>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
[jstultz: forward ported to mainline, reworded commit log, reworked
to only check trb->ctrl as suggested by Felipe]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Here is the big USB and Thunderbolt and PHY driver updates for 5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code has
begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFTNw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynpKQCgrh2FoobS2x0oFg/OUHdjokQV/BYAoJGWLOmt
8S5cnsCuLq3w5qpCcBva
=PMGd
-----END PGP SIGNATURE-----
Merge tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
Add support for reference properties in sofrware nodes (Dmitry
Torokhov) and a basic test for property entries along with fixes
on top of it (Dmitry Torokhov, Qian Cai, Alan Maguire).
-----BEGIN PGP SIGNATURE-----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=wnoj
-----END PGP SIGNATURE-----
Merge tag 'devprop-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"Add support for reference properties in sofrware nodes (Dmitry
Torokhov) and a basic test for property entries along with fixes on
top of it (Dmitry Torokhov, Qian Cai, Alan Maguire)"
* tag 'devprop-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
software node: introduce CONFIG_KUNIT_DRIVER_PE_TEST
usb: dwc3: use proper initializers for property entries
drivers/base/test: fix global-out-of-bounds error
software node: add basic tests for property entries
software node: remove separate handling of references
platform/x86: intel_cht_int33fe: use inline reference properties
software node: implement reference properties
software node: allow embedding of small arrays into property_entry
software node: replace is_array with is_inline
There is one more Comet Lake PCH variant, CML-V, that has
its own PCI ID.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200117093033.48616-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had a 100us delay to synchronize the END_TRANSFER command completion
before giving back requests to the function drivers. Now, the controller
driver can handle cancelled TRBs with the requests' cancelled_list and
it can also wait until the END_TRANSFER completion before starting new
transfers. Synchronization can simply base on the controller's command
completion interrupt. The 100us delay is no longer needed. Remove this
arbitrary delay.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the END_TRANSFER command hasn't completed yet, then don't send the
START_TRANSFER command. The controller may not be able to start if
that's the case. Some controller revisions depend on this. See
commit 76a638f8ac ("usb: dwc3: gadget: wait for End Transfer to
complete"). Let's only send START_TRANSFER command after the
END_TRANSFER command had completed.
Fixes: 3aec99154d ("usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the END_TRANSFER command is sent but not completed, any request
dequeue during this time will cause the driver to issue the END_TRANSFER
command. The driver needs to submit the command only once to stop the
controller from processing further. The controller may take more time to
process the same command multiple times unnecessarily. Let's add a flag
DWC3_EP_END_TRANSFER_PENDING to check for this condition.
Fixes: 3aec99154d ("usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VBUS should be turned off when leaving the host mode.
Set GCTL_PRTCAP to device mode in teardown to de-assert DRVVBUS pin to
turn off VBUS power.
Fixes: 5f94adfeed ("usb: dwc3: core: refactor mode initialization to its own function")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Send a no-action link state change request before the actual request
so DWC3 can send the same request whenever we call
dwc3_gadget_set_link_state().
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DWC3 receives disconnect event, it needs to set the link state to
RX_Detect.
DWC_usb3 3.30a programming guide 4.1.7
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DCTL.ULSTCHNGREQ is a write-only field. When doing a read-modify-write
to DCTL, the driver must make sure that there's no unintended link state
change request from whatever is read from DCTL.ULSTCHNGREQ. Set link
state change to no-action when the driver writes to DCTL.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200104152107.11407-9-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not be reaching into property entries and initialize them by
hand, but rather use proper initializer macros. This way we can alter
internal representation of property entries with no visible changes to
their users.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The original ID that was added for Comet Lake PCH was
actually for the -LP (low power) variant even though the
constant for it said CMLH. Changing that while at it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191212093713.60614-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear ep0's DWC3_EP_TRANSFER_STARTED flag if the END_TRANSFER command is
completed. Otherwise, we can't start control transfer again after
END_TRANSFER.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Normally the END_TRANSFER command completion handler will clear the
DWC3_EP_TRANSFER_STARTED flag. However, if the command was sent without
interrupt on completion, then the flag will not be cleared. Make sure to
clear the flag in this case.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the condition to kick the transfer without
giving back the requests when either request has remaining data
or when there are pending SGs. The && check was introduced during
spliting up the dwc3_gadget_ep_cleanup_completed_requests() function.
Fixes: f38e35dd84 ("usb: dwc3: gadget: split dwc3_gadget_ep_cleanup_completed_requests()")
Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191121132914.29368-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have TI's glue layer for the Cadence USB3 controller going
upstream. Tegra's XUDC driver is also going upstream with this pull
request.
Apart from these two big features, we have a bunch of patches switching
over to devm_platform_ioremap_resource() in order to simplify code a
little; and a non-critical fix for DWC3 usage via kexec.
-----BEGIN PGP SIGNATURE-----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=Xyc8
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.5
We have TI's glue layer for the Cadence USB3 controller going
upstream. Tegra's XUDC driver is also going upstream with this pull
request.
Apart from these two big features, we have a bunch of patches switching
over to devm_platform_ioremap_resource() in order to simplify code a
little; and a non-critical fix for DWC3 usage via kexec.
* tag 'usb-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (44 commits)
usb: dwc3: of-simple: add a shutdown
usb: cdns3: Add TI specific wrapper driver
dt-bindings: usb: Add binding for the TI wrapper for Cadence USB3 controller
usb: mtu3: fix race condition about delayed_status
usb: gadget: Add UDC driver for tegra XUSB device mode controller
usb: dwc3: debug: Remove newline printout
usb: dwc2: use a longer core rest timeout in dwc2_core_reset()
usb: gadget: udc: lpc32xx: Use devm_platform_ioremap_resource() in lpc32xx_udc_probe()
USB: gadget: udc: clean up an indentation issue
usb: gadget: Quieten gadget config message
phy: renesas: rcar-gen3-usb2: Use platform_get_irq_optional() for optional irq
usb: gadget: Remove set but not used variable 'opts' in msg_do_config
usb: gadget: Remove set but not used variable 'opts' in acm_ms_do_config
usb: mtu3: add a new function to do status stage
usb: gadget: configfs: fix concurrent issue between composite APIs
usb: gadget: f_tcm: Provide support to get alternate setting in tcm function
usb: gadget: Correct NULL pointer checking in fsl gadget
usb: fsl: Remove unused variable
USB: dummy-hcd: use usb_urb_dir_in instead of usb_pipein
USB: dummy-hcd: increase max number of devices to 32
...
Now the USB gadget subsystem can use the USB debugfs root directory,
so move dwc3's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1573541519-28488-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disabling an endpoint which has cancelled requests, we should
make sure to giveback requests that are currently pending in the
cancelled list, otherwise we may fall into a situation where command
completion interrupt fires after endpoint has been disabled, therefore
causing a splat.
Fixes: fec9095bde "usb: dwc3: gadget: remove wait_end_transfer"
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191031090713.1452818-1-felipe.balbi@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case we're loading a new kernel via kexec, let's make sure to
cleanup the dwc3 address space correctly. This means that we should
run the same steps from driver remove, so just extract a reusable
function for both cases.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
layerscape board sometimes reported some usb call trace, that is due to
kernel sent LPM tokerns automatically when it has no pending transfers
and think that the link is idle enough to enter L1, which procedure will
ask usb register has a recovery,then kernel will compare USBx_GFLADJ and
set GFLADJ_30MHZ, GFLADJ_30MHZ_REG until GFLADJ_30MHZ is equal 0x20, if
the conditions were met then issue occur, but whatever the conditions
whether were met that usb is all need keep GFLADJ_30MHZ of value is 0x20
(xhci spec ask use GFLADJ_30MHZ to adjust any offset from clock source
that generates the clock that drives the SOF counter, 0x20 is default
value of it)That is normal logic, so need remove the call trace.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc3_pci_probe a call to platform_device_alloc allocates a device
which is correctly put in case of error except one case: when the call to
platform_device_add_properties fails it directly returns instead of
going to error handling. This commit replaces return with the goto.
Fixes: 1a7b12f69a ("usb: dwc3: pci: Supply device properties via driver data")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After many randconfig builds, one configuration caused a link
error with dwc3-meson-g12a lacking the regmap-mmio code:
drivers/usb/dwc3/dwc3-meson-g12a.o: In function `dwc3_meson_g12a_probe':
dwc3-meson-g12a.c:(.text+0x9f): undefined reference to `__devm_regmap_init_mmio_clk'
Add the select statement that we have for all other users
of that dependency.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The newline from the unknown link state tracepoint doesn't follow the
other tracepoints, and it looks unsightly. Let's remove it.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For DRD controllers, the programming guide recommended that
GUSB3PIPECTL.SUSPENDABLE and GUSB2PHYCFG.SUSPHY to be cleared after
power-on reset and only set after the controller initialization is
completed. This can be done after device soft-reset in dwc3_core_init().
This patch makes sure to clear GUSB3PIPECTL.SUSPENDABLE and
GUSB2PHYCFG.SUSPHY before core initialization and only set them after
the device soft-reset is completed.
Reference: DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section
1.2.49 and 1.2.45
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()"), platform_get_irq() will call dev_err() itself on
failure, so there is no need for the driver to also do this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191005210449.3926-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3 code to get the "peripheral" / "host" / "otg" IRQ first tries
platform_get_irq_byname() and then falls back to the IRQ at index 0 if
the platform_get_irq_byname().
In this case we do not want platform_get_irq_byname() to print an error
on failure, so switch to platform_get_irq_byname_optional() instead which
does not print an error.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205037
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191005210449.3926-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190923154956.6868-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calls to USB2 generic PHY calibrate() method has been moved to HCD core,
which now successfully handles generic PHYs and their calibration after
every HCD reset. This fixes all the timing issues related to PHY
calibration done directly from DWC3 driver: incorrect operation after
system suspend/resume or USB3.0 detection failure when XHCI-plat driver
compiled as separate module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Jochen Sprickerhof <jochen@sprickerhof.de>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20190829053028.32438-3-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With only 45 non-merge commits, we have a small merge window from the
Gadget perspective.
The biggest change here is the addition of the Cadence USB3 DRD
Driver. All other changes are small, non-critical fixes or smaller new
features like the improvement to BESL handling in dwc3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=KUJN
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: Changes for v5.4 merge window
With only 45 non-merge commits, we have a small merge window from the
Gadget perspective.
The biggest change here is the addition of the Cadence USB3 DRD
Driver. All other changes are small, non-critical fixes or smaller new
features like the improvement to BESL handling in dwc3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* tag 'usb-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (45 commits)
usb: gadget: net2280: Add workaround for AB chip Errata 11
usb: gadget: net2280: Move all "ll" registers in one structure
usb: dwc3: gadget: Workaround Mirosoft's BESL check
usb:cdns3 Fix for stuck packets in on-chip OUT buffer.
usb: cdns3: Add Cadence USB3 DRD Driver
usb: common: Simplify usb_decode_get_set_descriptor function.
usb: common: Patch simplify usb_decode_set_clear_feature function.
usb: common: Separated decoding functions from dwc3 driver.
dt-bindings: add binding for USBSS-DRD controller.
usb: gadget: composite: Set recommended BESL values
usb: dwc3: gadget: Set BESL config parameter
usb: dwc3: Separate field holding multiple properties
usb: gadget: Export recommended BESL values
usb: phy: phy-fsl-usb: Make structure fsl_otg_initdata constant
usb: udc: lpc32xx: silence fall-through warning
usb: dwc3: meson-g12a: fix suspend resume regulator unbalanced disables
usb: udc: lpc32xx: remove set but not used 3 variables
usb: gadget: udc: core: Fix segfault if udc_bind_to_driver() for pending driver fails
usb: dwc3: st: Add of_dev_put() in probe function
usb: dwc3: st: Add of_node_put() before return in probe function
...
While testing our host system using Microsoft's usb stack against our
gadget for various BESL values, we found an issue with their usb stack
when the recommended baseline BESL value is 0 (125us) or when the deep
BESL is 1 or less. The Windows host will issue a usb reset immediately
after it receives the extended BOS descriptor and the enumeration will
fail after a few attempts.
To keep compatibility with Microsoft's host usb stack, let's workaround
this issue by using the recommended baseline BESL of 1 (or 150us)
and clamp the deep BESL value within 2 to 15.
This was tested against Windows 10 build 18956.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Patch moves some decoding functions from driver/usb/dwc3/debug.h driver
to driver/usb/common/debug.c file. These moved functions include:
dwc3_decode_get_status
dwc3_decode_set_clear_feature
dwc3_decode_set_address
dwc3_decode_get_set_descriptor
dwc3_decode_get_configuration
dwc3_decode_set_configuration
dwc3_decode_get_intf
dwc3_decode_set_intf
dwc3_decode_synch_frame
dwc3_decode_set_sel
dwc3_decode_set_isoch_delay
dwc3_decode_ctrl
These functions are used also in inroduced cdns3 driver.
All functions prefixes were changed from dwc3 to usb.
Also, function's parameters has been extended according to the name
of fields in standard SETUP packet.
Additionally, patch adds usb_decode_ctrl function to
include/linux/usb/ch9.h file.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When operating with LPM signals, the controller asserts the deep
low-power signal (utmi_l1_suspend_n) to the phy when the BESL value of
the LPM token is equal to or greater than DCTL.HIRD_Thres[3:0] (and
with DCTL.HIRD_Thres[4] set). Otherwise, the shallow low-power signal
(utmi_sleep_n) is asserted. Set the recommended deep BESL equal to the
controller's DCTL.HIRD_Thres[3:0] setting, and set the baseline BESL
to 0 for the shallow low-power signal. This maximizes the opportunity
for L1 residency and optimizes power savings.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc->hird_threshold field should store "snps,hird_threshold" property
only and not a combination of multiple properties. Remove the value of
"snps,is-utmi-l1-suspend" property from the field dwc->hird_threshold.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When going in suspend, in Device mode, then resuming back leads
to the following:
unbalanced disables for USB_PWR_EN
WARNING: CPU: 0 PID: 163 at ../drivers/regulator/core.c:2590 _regulator_disable+0x104/0x180
Hardware name: Amlogic Meson G12A U200 Development Board (DT)
[...]
pc : _regulator_disable+0x104/0x180
lr : _regulator_disable+0x104/0x180
[...]
Call trace:
_regulator_disable+0x104/0x180
regulator_disable+0x40/0x78
dwc3_meson_g12a_otg_mode_set+0x84/0xb0
dwc3_meson_g12a_irq_thread+0x58/0xb8
irq_thread_fn+0x28/0x80
irq_thread+0x118/0x1b8
kthread+0xf4/0x120
ret_from_fork+0x10/0x18
This disables the regulator if enabled on suspend, and the reverse on
resume.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reported-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In function st_dwc3_probe, variable child_pdev takes the value returned
by of_find_device_by_node, which gets a device pointer but does not put
it. If child_pdev is not put before the probe function returns, it may
cause a reference leak. Hence put child_pdev after its last usage.
Issue found with Coccinelle.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The local variable child in the function st_dwc3_probe takes the return
value of of_get_child_by_name, which gets a node and does not put it. If
the function returns without releasing child, this could cause a memory
error. Hence put child as soon as there is no more use for it. Also
create a new label, err_node_put, just before label undo_softreset; so
that err_node_put puts child. In between initialisation of child and its
first put, modify all statements that go to undo_softreset to now go to
err_node_put instead, from where they can fall through to
undo_softreset.
Issue found with Coccinelle.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts
commit 6a4290cc28 ("usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.")
We don't yet support any of the OTG mechanisms (HNP/SRP/ADP)
and are not setting gadget->otg_caps, so don't set gadget->is_otg
flag.
If we do then we end up publishing a OTG1.0 descriptor in
the gadget descriptor which causes device enumeration to fail
if we are connected to a host with CONFIG_USB_OTG enabled.
Host side log without this patch
[ 96.720453] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 96.901391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 96.907552] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.060447] usb 1-1: new high-speed USB device number 3 using xhci-hcd
[ 97.241378] usb 1-1: Dual-Role OTG device on non-HNP port
[ 97.247536] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.253606] usb usb1-port1: attempt power cycle
[ 97.960449] usb 1-1: new high-speed USB device number 4 using xhci-hcd
[ 98.141383] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.147540] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.300453] usb 1-1: new high-speed USB device number 5 using xhci-hcd
[ 98.481391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.487545] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.493532] usb usb1-port1: unable to enumerate USB device
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use clk_bulk_prepare_enable() and clk_bulk_disable_unprepare() to
simplify code a bit. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devres to get clocks and drop explicit clock freeing. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 08f871a3ac ("usb: dwc3: host: convey the PHYs to xhci") added
forwarding of the generic PHYs from DWC3 core to the instantiated XHCI-plat
device. However XHCI(-plat) driver never gained support for generic PHYs,
thus the lookup added by that commit is never used. In meantime the commit
d64ff406e5 ("usb: dwc3: use bus->sysdev for DMA configuration")
incorrectly changed the device used for creating lookup, making the lookup
useless and generic PHYs inaccessible from XHCI device.
However since commit 178a0bce05 ("usb: core: hcd: integrate the PHY
wrapper into the HCD core") USB HCD already handles generic PHYs acquired
from the HCD's 'sysdev', which in this case is DWC3 core device. This means
that creating any custom lookup entries for XHCI driver is no longer needed
and can be simply removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Starting from DWC_usb31 version 1.90a and later, the DCTL.CSFRST bit
will not be cleared until after all the internal clocks are synchronized
during soft-reset. This may take a little more than 50ms. Set the
polling rate at 20ms instead.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This enum is only used in drivers/usb/dwc3/dwc3-omap3.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use use device_property_count_u32() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20190802130408.20336-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-47-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch moves some decoding functions from driver/usb/dwc3/debug.h driver
to driver/usb/gadget/debug.c file. These moved functions include:
dwc3_decode_get_status
dwc3_decode_set_clear_feature
dwc3_decode_set_address
dwc3_decode_get_set_descriptor
dwc3_decode_get_configuration
dwc3_decode_set_configuration
dwc3_decode_get_intf
dwc3_decode_set_intf
dwc3_decode_synch_frame
dwc3_decode_set_sel
dwc3_decode_set_isoch_delay
dwc3_decode_ctrl
These functions are used also in inroduced cdns3 driver.
All functions prefixes were changed from dwc3 to usb.
Also, function's parameters has been extended according to the name
of fields in standard SETUP packet.
Additionally, patch adds usb_decode_ctrl function to
include/linux/usb/gadget.h file.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The member @lock of dwc3_ep struct is only initialized,
and not used elsewhere, so remove it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget applications may have a requirement to disable the U1 and U2
entry based on the usecase. Below are few usecases where the disabling
U1/U2 entries may be possible.
Usecase 1:
When combining dwc3 with an redriver for a USB Type-C device solution, it
sometimes have problems with leaving U1/U2 for certain hosts, resulting in
link training errors and reconnects. For this U1/U2 state entries may be
avoided.
Usecase 2:
When performing performance benchmarking on mass storage gadget the
U1 and U2 entries can be disabled.
Usecase 3:
When periodic transfers like ISOC transfers are used with bInterval
of 1 which doesn't require the link to enter into U1 or U2 state entry
(since ping is issued from host for every uframe interval). In this
case the U1 and U2 entry can be disabled.
Disablement of U1/U2 can be done by setting U1DevExitLat and U2DevExitLat
values to 0 in the BOS descriptor. Host on seeing 0 value for U1DevExitLat
and U2DevExitLat, it doesn't send SET_SEL requests to the gadget. There
may be some hosts which may send SET_SEL requests even after seeing 0 in
the UxDevExitLat of BOS descriptor. To aviod U1/U2 entries for these type
of hosts, dwc3 controller can be programmed to reject those U1/U2 requests
by not enabling ACCEPTUxENA bits in DCTL register.
This patch updates the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use of_clk_get_parent_count() instead of open coding.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The required clocks needs to be enabled before the first register
access. After commit fe8abf332b ("usb: dwc3: support clocks and resets
for DWC3 core"), this happens when the dwc3_core_is_valid function is
called, but the mentioned commit adds that call in the wrong place,
before the clocks are enabled. So, move that call after the
clk_bulk_enable() to ensure the clocks are enabled and the reset
deasserted.
I detected this while, as experiment, I tried to move the clocks and resets
from the glue layer to the DWC3 core on a Samsung Chromebook Plus.
That was not detected before because, in most cases, the glue layer
initializes SoC-specific things and then populates the child "snps,dwc3"
with those clocks already enabled.
Fixes: b873e2d0ea ("usb: dwc3: Do core validation early on probe")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_qcom_clk_init() is called with of_count_phandle_with_args() as an
argument. If of_count_phandle_with_args() returns an error, the number
of clocks will be a negative value and will lead to undefined behaviour.
Ensure we check for an error before attempting to blindly use the value.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When booting with Device Tree, the current default boot configuration
table option, the request to boot via 'host mode' comes from the
'dr_mode' property. A property of the same name can be used inside
ACPI tables too. However it is missing from the SDM845's ACPI tables
so we have to supply this information using Platform Device Properties
instead.
This does not change the behaviour of any currently supported devices.
The property is only set on ACPI enabled platforms, thus for H/W
booting DT, unless a 'dr_mode' property is present, the default is
still OTG (On-The-Go) as per [0]. Any new ACPI devices added will
also be able to over-ride this implementation by providing a 'dr_mode'
property in their ACPI tables. In cases where 'dr_mode' is omitted
from the tables AND 'host mode' should not be the default (very
unlikely), then we will have to add some way of choosing between them
at run time - most likely by ACPI HID.
[0] Documentation/devicetree/bindings/usb/generic.txt
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In Linux, the DWC3 core exists as its own independent platform device.
Thus when describing relationships in Device Tree, the current default
boot configuration table option, the DWC3 core often resides as a child
of the platform specific node. Both of which are given their own
address space descriptions and the drivers can be mostly agnostic to
each other.
However, other Operating Systems have taken a more monolithic approach,
which is evident in the configuration ACPI tables for the Qualcomm
Snapdragon SDM850, where all DWC3 (core and platform) components are
described under a single IO memory region.
To ensure successful booting using the supplied ACPI tables, we need to
devise a way to chop up the address regions provided and subsequently
register the DWC3 core with the resultant information, which is
precisely what this patch aims to achieve.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add support for the OTG ID change interrupt to switch between Host
and Device mode.
Tested on the Hardkernel Odroid-N2 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=YFiQ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This has two exciting community drivers for ARM Mali accelerators.
Since ARM has never been open source friendly on the GPU side of the
house, the community has had to create open source drivers for the
Mali GPUs. Lima covers the older t4xx and panfrost the newer 6xx/7xx
series. Well done to all involved and hopefully this will help ARM
head in the right direction.
There is also now the ability if you don't have any of the legacy
drivers enabled (pre-KMS) to remove all the pre-KMS support code from
the core drm, this saves 10% or so in codesize on my machine.
i915 also enable Icelake/Elkhart Lake Gen11 GPUs by default, vboxvideo
moves out of staging.
There are also some rcar-du patches which crossover with media tree
but all should be acked by Mauro.
Summary:
uapi changes:
- Colorspace connector property
- fourcc - new YUV formts
- timeline sync objects initially merged
- expose FB_DAMAGE_CLIPS to atomic userspace
new drivers:
- vboxvideo: moved out of staging
- aspeed: ASPEED SoC BMC chip display support
- lima: ARM Mali4xx GPU acceleration driver support
- panfrost: ARM Mali6xx/7xx Midgard/Bitfrost acceleration driver support
core:
- component helper docs
- unplugging fixes
- devm device init
- MIPI/DSI rate control
- shmem backed gem objects
- connector, display_info, edid_quirks cleanups
- dma_buf fence chain support
- 64-bit dma-fence seqno comparison fixes
- move initial fb config code to core
- gem fence array helpers for Lima
- ability to remove legacy support code if no drivers requires it (removes 10% of drm.ko size)
- lease fixes
ttm:
- unified DRM_FILE_PAGE_OFFSET handling
- Account for kernel allocations in kernel zone only
panel:
- OSD070T1718-19TS panel support
- panel-tpo-td028ttec1 backlight support
- Ronbo RB070D30 MIPI/DSI
- Feiyang FY07024DI26A30-D MIPI-DSI panel
- Rocktech jh057n00900 MIPI-DSI panel
i915:
- Comet Lake (Gen9) PCI IDs
- Updated Icelake PCI IDs
- Elkhartlake (Gen11) support
- DP MST property addtions
- plane and watermark fixes
- Icelake port sync and VEBOX disable fixes
- struct_mutex usage reduction
- Icelake gamma fix
- GuC reset fixes
- make mmap more asynchronous
- sound display power well race fixes
- DDI/MIPI-DSI clocks for Icelake
- Icelake RPS frequency changing support
- Icelake workarounds
amdgpu:
- Use HMM for userptr
- vega20 experimental smu11 support
- RAS support for vega20
- BACO support for vega12 + fixes for vega20
- reworked IH interrupt handling
- amdkfd RAS support
- Freesync improvements
- initial timeline sync object support
- DC Z ordering fixes
- NV12 planes support
- colorspace properties for planes=
- eDP opts if eDP already initialized
nouveau:
- misc fixes
etnaviv:
- misc fixes
msm:
- GPU zap shader support expansion
- robustness ABI addition
exynos:
- Logging cleanups
tegra:
- Shared reset fix
- CPU cache maintenance fix
cirrus:
- driver rewritten using simple helpers
meson:
- G12A support
vmwgfx:
- Resource dirtying management improvements
- Userspace logging improvements
virtio:
- PRIME fixes
rockchip:
- rk3066 hdmi support
sun4i:
- DSI burst mode support
vc4:
- load tracker to detect underflow
v3d:
- v3d v4.2 support
malidp:
- initial Mali D71 support in komeda driver
tfp410:
- omap related improvement
omapdrm:
- drm bridge/panel support
- drop some omap specific panels
rcar-du:
- Display writeback support"
* tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm: (1507 commits)
drm/msm/a6xx: No zap shader is not an error
drm/cma-helper: Fix drm_gem_cma_free_object()
drm: Fix timestamp docs for variable refresh properties.
drm/komeda: Mark the local functions as static
drm/komeda: Fixed warning: Function parameter or member not described
drm/komeda: Expose bus_width to Komeda-CORE
drm/komeda: Add sysfs attribute: core_id and config_id
drm: add non-desktop quirk for Valve HMDs
drm/panfrost: Show stored feature registers
drm/panfrost: Don't scream about deferred probe
drm/panfrost: Disable PM on probe failure
drm/panfrost: Set DMA masks earlier
drm/panfrost: Add sanity checks to submit IOCTL
drm/etnaviv: initialize idle mask before querying the HW db
drm: introduce a capability flag for syncobj timeline support
drm: report consistent errors when checking syncobj capibility
drm/nouveau/nouveau: forward error generated while resuming objects tree
drm/nouveau/fb/ramgk104: fix spelling mistake "sucessfully" -> "successfully"
drm/nouveau/i2c: Disable i2c bus access after ->fini()
drm/nouveau: Remove duplicate ACPI_VIDEO_NOTIFY_PROBE definition
...
The macro name DWC3_DCTL_LPM_ERRATA is uninformative and does not do
masking. Remove DWC3_DCTL_LPM_ERRATA_MASK and rename
DWC3_DCTL_LPM_ERRATA to DWC3_DCTL_NYET_THRES with proper masking.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The max possible value for DCTL.LPM_NYET_THRES is 15 and not 255. Change
the default value to 15.
Cc: stable@vger.kernel.org
Fixes: 80caf7d21a ("usb: dwc3: add lpm erratum support")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 is missing the printing of control request GET_STATUS(device)
tracepoint. This patch prints that.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The setting of the dr_mode may need to check the controller's revision.
The revision is set in the dwc3_core_is_valid(), which comes after
dr_mode setting. Let's move it closer to the start of the dwc3_probe()
function and before calling dwc3_get_dr_mode().
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All DWC3 controllers are LPM capable. Report that in the
usb_gadget.lpm_capable for the gadget driver to properly output the
bcdUSB value in the descriptor.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_gadget_suspend() is called under dwc->lock spinlock. In such context
calling synchronize_irq() is not allowed. Move the problematic call out
of the protected block to fix the following kernel BUG during system
suspend:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:112
in_atomic(): 1, irqs_disabled(): 128, pid: 1601, name: rtcwake
6 locks held by rtcwake/1601:
#0: f70ac2a2 (sb_writers#7){.+.+}, at: vfs_write+0x130/0x16c
#1: b5fe1270 (&of->mutex){+.+.}, at: kernfs_fop_write+0xc0/0x1e4
#2: 7e597705 (kn->count#60){.+.+}, at: kernfs_fop_write+0xc8/0x1e4
#3: 8b3527d0 (system_transition_mutex){+.+.}, at: pm_suspend+0xc4/0xc04
#4: fc7f1c42 (&dev->mutex){....}, at: __device_suspend+0xd8/0x74c
#5: 4b36507e (&(&dwc->lock)->rlock){....}, at: dwc3_gadget_suspend+0x24/0x3c
irq event stamp: 11252
hardirqs last enabled at (11251): [<c09c54a4>] _raw_spin_unlock_irqrestore+0x6c/0x74
hardirqs last disabled at (11252): [<c09c4d44>] _raw_spin_lock_irqsave+0x1c/0x5c
softirqs last enabled at (9744): [<c0102564>] __do_softirq+0x3a4/0x66c
softirqs last disabled at (9737): [<c0128528>] irq_exit+0x140/0x168
Preemption disabled at:
[<00000000>] (null)
CPU: 7 PID: 1601 Comm: rtcwake Not tainted
5.0.0-rc3-next-20190122-00039-ga3f4ee4f8a52 #5252
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c01110f0>] (unwind_backtrace) from [<c010d120>] (show_stack+0x10/0x14)
[<c010d120>] (show_stack) from [<c09a4d04>] (dump_stack+0x90/0xc8)
[<c09a4d04>] (dump_stack) from [<c014c700>] (___might_sleep+0x22c/0x2c8)
[<c014c700>] (___might_sleep) from [<c0189d68>] (synchronize_irq+0x28/0x84)
[<c0189d68>] (synchronize_irq) from [<c05cbbf8>] (dwc3_gadget_suspend+0x34/0x3c)
[<c05cbbf8>] (dwc3_gadget_suspend) from [<c05bd020>] (dwc3_suspend_common+0x154/0x410)
[<c05bd020>] (dwc3_suspend_common) from [<c05bd34c>] (dwc3_suspend+0x14/0x2c)
[<c05bd34c>] (dwc3_suspend) from [<c051c730>] (platform_pm_suspend+0x2c/0x54)
[<c051c730>] (platform_pm_suspend) from [<c05285d4>] (dpm_run_callback+0xa4/0x3dc)
[<c05285d4>] (dpm_run_callback) from [<c0528a40>] (__device_suspend+0x134/0x74c)
[<c0528a40>] (__device_suspend) from [<c052c508>] (dpm_suspend+0x174/0x588)
[<c052c508>] (dpm_suspend) from [<c0182134>] (suspend_devices_and_enter+0xc0/0xe74)
[<c0182134>] (suspend_devices_and_enter) from [<c0183658>] (pm_suspend+0x770/0xc04)
[<c0183658>] (pm_suspend) from [<c0180ddc>] (state_store+0x6c/0xcc)
[<c0180ddc>] (state_store) from [<c09a9a70>] (kobj_attr_store+0x14/0x20)
[<c09a9a70>] (kobj_attr_store) from [<c02d6800>] (sysfs_kf_write+0x4c/0x50)
[<c02d6800>] (sysfs_kf_write) from [<c02d594c>] (kernfs_fop_write+0xfc/0x1e4)
[<c02d594c>] (kernfs_fop_write) from [<c02593d8>] (__vfs_write+0x2c/0x160)
[<c02593d8>] (__vfs_write) from [<c0259694>] (vfs_write+0xa4/0x16c)
[<c0259694>] (vfs_write) from [<c0259870>] (ksys_write+0x40/0x8c)
[<c0259870>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xed55ffa8 to 0xed55fff0)
...
Fixes: 01c10880d2 ("usb: dwc3: gadget: synchronize_irq dwc irq in suspend")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we read an array of integers from device properties,
the temporary buffer is allocated.
However, in case of dwc3_set_incr_burst_type() it's not freed.
Free allocated buffer immediately after use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that the bulk API has a "get all of the clocks" helper to match
what this code wants, there's little reason not to switch over.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Adds support for Amlogic G12A USB Control Glue HW.
The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only
A glue connects these both controllers to 2 USB2 PHYs, and optionnally
to an USB3+PCIE Combo PHY shared with the PCIE controller.
The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.
This drivers supports the on-probe setup of the OTG mode, and manually
via a debugfs interface. The IRQ mode change detect is yet to be added
in a future patchset, mainly due to lack of hardware to validate on.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Keep EXTCON support optional, as some platforms do not need it.
Do the same for USB_DWC3_OMAP while we're at it.
Fixes: 3def4031b3 ("usb: dwc3: add EXTCON dependency for qcom")
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This contains a fix for the usage of shared resets that previously
generated a WARN on boot. In addition, there's a fix for CPU cache
maintenance of GEM buffers allocated using get_pages().
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAly4k7gTHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoUqkD/oC21pwikg0nYh1LoiH7GbmA3NPm56o
Ei0cx9p8KyHUT0ongxmr0wfvyfCjwCqlFPWJOZrFOXjUmIupUooTbsqnAiHwEQE8
6m2FaZXRpYc8VYk7+uW4u1MhmWr7fStuxVs/GKVZBK7jaxn3MXouL6fP3cOc8QK1
GZdek2hxMDkvK1PnDc0MRx+COxsi3pMRL8hwBj++1EWPh3SGuOBsaj8S9dxXwSXH
TrNCIpGV6BOL6y9g9uDGmqDM6lef90Dx0mRneuWK3pQoCbQJDMUsdVuNEKYI+wqZ
hrfG9TZWeamK42OSX5GDM/DJwtb2K1z58Z410dlmc1IK9Inw7LcpYDHdoZQSmBgv
5KwYgeqjQSYV9Ok1D0SY3grdroufg6PSHuE+VgD4SpQ4pbBrBvPUqxpi4icY0re9
Td3FBzHzEMB14QWXIKWXfG7fd9pAKSesxaRaI3G9mtJrI1kIeRa3/0z8MQtSwbOg
fxAZYXkCS2aeo9h6Owmhqm/lgYuv/SJ/1NOwLVJ6tgoI1rN0ukMe2OCPCOFmY7AJ
ehiVBfXY7bjVYW3yhCUdm4w5ju/lmO5g2N4nqdpmcpvOz4QZE0aviPqcA5hiMfMQ
5WKakqrJ1NGVMTQtKJxGgUq3BXEFqnMpKUkUMT+KVQinMjZOEu1klxlg4ScyZVdd
Ly0z3PjsUbv+6g==
=nA5m
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.2-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.2-rc1
This contains a fix for the usage of shared resets that previously
generated a WARN on boot. In addition, there's a fix for CPU cache
maintenance of GEM buffers allocated using get_pages().
(airlied: contains a merge from a shared tegra tree)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190418151447.9430-1-thierry.reding@gmail.com
In order to be able to request an array of reset controls in acquired or
released mode, add the acquired flag to of_reset_control_array_get() and
pass the flag to subsequent calls of __of_reset_control_get().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
In case the "linux,extcon-name" property is defined but device itself
is not ready, defer the probe.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
-----BEGIN PGP SIGNATURE-----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=4fTL
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.1 merge window
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
* tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (40 commits)
usb: phy: twl6030-usb: fix possible use-after-free on remove
usb: misc: usbtest: add super-speed isoc support
usb: dwc3: Reset num_trbs after skipping
usb: dwc3: gadget: don't enable interrupt when disabling endpoint
fotg210-udc: pass struct device to DMA API functions
fotg210-udc: remove a bogus dma_sync_single_for_device call
usb: gadget: Change Andrzej Pietrasiewicz's e-mail address
usb: f_fs: Avoid crash due to out-of-scope stack ptr access
usb: dwc3: haps: Workaround matching VID PID
usb: gadget: f_fs: preserve wMaxPacketSize across usb_ep_autoconfig() call
usb: gadget: move non-super speed code out of usb_ep_autoconfig_ss()
usb: gadget: function: sync f_uac1 ac header baInterfaceNr
usb: dwc2: gadget: Add scatter-gather mode
usb: gadget: fix various indentation issues
usb: dwc2: Fix EP TxFIFO number setting
udc: net2280: Fix net2280_disable
USB: gadget: Improve kerneldoc for usb_ep_dequeue()
usb: dwc3: debug: purge usage of strcat
usb: dwc3: trace: pass trace buffer size to decoding functions
usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING
...
Currently req->num_trbs is not reset after the TRBs are skipped and
processed from the cancelled list. The gadget driver may reuse the
request with an invalid req->num_trbs, and DWC3 will incorrectly skip
trbs. To fix this, simply reset req->num_trbs to 0 after skipping
through all of them.
Fixes: c3acd59014 ("usb: dwc3: gadget: use num_trbs when skipping TRBs on ->dequeue()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since we're disabling the endpoint anyway, we don't worry about
getting endpoint command completion interrupt.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
i.MX6QP and i.MX7D platform use a PCIe controller with the same VID and
PID as this USB controller. The system may incorrectly match this driver
to that PCIe controller. To workaround this, specifically use class type
USB with PCI device ID to prevent incorrect driver matching.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of assuming that our buffer is big enough, let's pass the
buffer size around so printing functions can make sure they won't
overflow the buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we modified the code to fix a race condition, it's clear that
DWC3_EP_END_TRANSFER_PENDING is unnecessary, considering that
DWC3_EP_TRANSFER_STARTED will remain set until End Transfer completes.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is a rare race condition that may happen during a Disconnect
Interrupt if we have a started request that happens to be
dequeued *after* completion of End Transfer command. If that happens,
that request will be left waiting for completion of an End Transfer
command that will never happen.
If End Transfer command has already completed before, we are safe to
giveback the request straight away.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have a proper flag for testing that we have a valid transfer in
flight, let's use that instead.
This patch is in preparation to fix a rare race condition that happens
upon Disconnect Interrupt.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We must wait until End Transfer completes in order to clear
DWC3_EP_TRANSFER_STARTED, otherwise we may confuse the driver.
This patch is in preparation to fix a rare race condition that happens
upon Disconnect Interrupt.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If clk_prepare_enable() fails in dwc3_exynos_probe() or in
dwc3_exynos_resume(), exynos->clks[0] is left undisabled
because of usage preincrement in while condition.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 9f2168367a ("usb: dwc3: exynos: Rework clock handling and prepare for new variants")
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For OUT endpoints, zero-length transfers require MaxPacketSize buffer as
per the DWC_usb3 programming guide 3.30a section 4.2.3.3.
This patch fixes this by explicitly checking zero length
transfer to correctly pad up to MaxPacketSize.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we have req->status, we don't need this extra flag
anymore. It's safe to remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Queueing the same request twice can introduce hard-to-debug
problems. At least one function driver - Android's f_mtp.c - is known
to cause this problem.
While that function is out-of-tree, this is a problem that's easy
enough to avoid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch starts tracking dwc3_request status. A following patch will
build on top of this to prevent a request from being queued twice.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The AM654 SoC contains a DWC3 controller with TI specific
wrapper. Add support for that.
Unlike the Keystone 2 case, for AM654 We don't need to
process any IRQs for basic USB operation.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On v3.10a in dual-role mode, if port is in device mode
and gadget driver isn't loaded, the OTG event interrupts don't
come through.
It seems that if the core is configured to be OTG2.0 only,
then we can't leave the DCFG.DEVSPD at Super-speed (default)
if we expect OTG to work properly. It must be set to High-speed.
Fix this issue by configuring DCFG.DEVSPD to the supported
maximum speed at gadget init. Device tree still needs to provide
correct supported maximum speed for this to work.
This issue wasn't present on v2.40a but is seen on v3.10a.
It doesn't cause any side effects on v2.40a.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a MSM8998 specific DT compatible so that we can properly bind to the
device and enable the USB controller.
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles. Add
the correct GPL-2.0 identifier to them to make scanning tools happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the link_state is uninitialized and the default value is 0(U0)
before the first time we start the udc, and after we start the udc then
stop the udc, the link_state will be undefined.
We may have the following warnings if we start the udc again with
an undefined link_state:
WARNING: CPU: 0 PID: 327 at drivers/usb/dwc3/gadget.c:294 dwc3_send_gadget_ep_cmd+0x304/0x308
dwc3 100e0000.hidwc3_0: wakeup failed --> -22
[...]
Call Trace:
[<c010f270>] (unwind_backtrace) from [<c010b3d8>] (show_stack+0x10/0x14)
[<c010b3d8>] (show_stack) from [<c034a4dc>] (dump_stack+0x84/0x98)
[<c034a4dc>] (dump_stack) from [<c0118000>] (__warn+0xe8/0x100)
[<c0118000>] (__warn) from [<c0118050>](warn_slowpath_fmt+0x38/0x48)
[<c0118050>] (warn_slowpath_fmt) from [<c0442ec0>](dwc3_send_gadget_ep_cmd+0x304/0x308)
[<c0442ec0>] (dwc3_send_gadget_ep_cmd) from [<c0445e68>](dwc3_ep0_start_trans+0x48/0xf4)
[<c0445e68>] (dwc3_ep0_start_trans) from [<c0446750>](dwc3_ep0_out_start+0x64/0x80)
[<c0446750>] (dwc3_ep0_out_start) from [<c04451c0>](__dwc3_gadget_start+0x1e0/0x278)
[<c04451c0>] (__dwc3_gadget_start) from [<c04452e0>](dwc3_gadget_start+0x88/0x10c)
[<c04452e0>] (dwc3_gadget_start) from [<c045ee54>](udc_bind_to_driver+0x88/0xbc)
[<c045ee54>] (udc_bind_to_driver) from [<c045f29c>](usb_gadget_probe_driver+0xf8/0x140)
[<c045f29c>] (usb_gadget_probe_driver) from [<bf005424>](gadget_dev_desc_UDC_store+0xac/0xc4 [libcomposite])
[<bf005424>] (gadget_dev_desc_UDC_store [libcomposite]) from[<c023d8e0>] (configfs_write_file+0xd4/0x160)
[<c023d8e0>] (configfs_write_file) from [<c01d51e8>] (__vfs_write+0x1c/0x114)
[<c01d51e8>] (__vfs_write) from [<c01d5ff4>] (vfs_write+0xa4/0x168)
[<c01d5ff4>] (vfs_write) from [<c01d6d40>] (SyS_write+0x3c/0x90)
[<c01d6d40>] (SyS_write) from [<c0107400>] (ret_fast_syscall+0x0/0x3c)
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
OUT endpoint requests may somtimes have this flag set when
preparing to be submitted to HW indicating that there is an
additional TRB chained to the request for alignment purposes.
If that request is removed before the controller can execute the
transfer (e.g. ep_dequeue/ep_disable), the request will not go
through the dwc3_gadget_ep_cleanup_completed_request() handler
and will not have its needs_extra_trb flag cleared when
dwc3_gadget_giveback() is called. This same request could be
later requeued for a new transfer that does not require an
extra TRB and if it is successfully completed, the cleanup
and TRB reclamation will incorrectly process the additional TRB
which belongs to the next request, and incorrectly advances the
TRB dequeue pointer, thereby messing up calculation of the next
requeust's actual/remaining count when it completes.
The right thing to do here is to ensure that the flag is cleared
before it is given back to the function driver. A good place
to do that is in dwc3_gadget_del_and_unmap_request().
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: stable@vger.kernel.org
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We see dwc3 endpoint stopped by unwanted irq during
suspend resume test, which is caused dwc3 ep can't be started
with error "No Resource".
Here, add synchronize_irq before suspend to sync the
pending IRQ handlers complete.
Signed-off-by: Bo He <bo.he@intel.com>
Signed-off-by: Yu Wang <yu.y.wang@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move Synopsys HAPS platform device IDs to pci_ids.h so that both
drivers/pci/quirks.c and dwc3-haps driver can reference these IDs.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.
There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.
Apart from these, we have the usual set of non-critical fixes and new
features all over the place.
-----BEGIN PGP SIGNATURE-----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=n8VS
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB changes for v4.21
So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.
There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.
Apart from these, we have the usual set of non-critical fixes and new
features all over the place.
* tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (56 commits)
usb: dwc2: Fix disable all EP's on disconnect
usb: dwc3: gadget: Disable CSP for stream OUT ep
usb: dwc2: disable power_down on Amlogic devices
Revert "usb: dwc3: pci: Use devm functions to get the phy GPIOs"
USB: gadget: udc: s3c2410_udc: convert to DEFINE_SHOW_ATTRIBUTE
usb: mtu3: fix dbginfo in qmu_tx_zlp_error_handler
usb: dwc3: trace: add missing break statement to make compiler happy
usb: dwc3: gadget: Report isoc transfer frame number
usb: gadget: Introduce frame_number to usb_request
usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro
usb: renesas_usbhs: Remove dummy runtime PM callbacks
usb: dwc2: host: use hrtimer for NAK retries
usb: mtu3: clear SOFTCONN when clear USB3_EN if work as HS mode
usb: mtu3: enable SETUPENDISR interrupt
usb: mtu3: fix the issue about SetFeature(U1/U2_Enable)
usb: mtu3: enable hardware remote wakeup from L1 automatically
usb: mtu3: remove QMU checksum
usb/mtu3: power down device ip at setup
usb: dwc2: Disable power down feature on Samsung SoCs
usb: dwc3: Correct the logic for checking TRB full in __dwc3_prepare_one_trb()
...
In stream mode, when fast-forwarding TRBs, the stream number
is not cleared causing the new stream to not get assigned. So
we don't want controller to carry on transfers when short packet
is received. So disable the CSP for stream capable endpoint.
This is based on the 3.30a Programming guide, where table 3-1
device descriptor structure field definitions says for CSP bit
If this bit is 0, the controller generates an XferComplete event
and remove the stream. So if we keep CSP as 1 then switching between
streams would not happen as in stream mode, when fast-forwarding
TRBs, the stream number is not cleared causing the new stream to not get
assigned.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 211f658b7b ("usb: dwc3: pci: Use devm functions to get
the phy GPIOs") changed the code to claim the PHY GPIOs permanently
for Intel Baytrail devices.
This causes issues when the actual PHY driver attempts to claim the
same GPIO descriptors. For example, tusb1210 now fails to probe with:
tusb1210: probe of dwc3.0.auto.ulpi failed with error -16 (EBUSY)
dwc3-pci needs to turn on the PHY once before dwc3 is loaded, but
usually the PHY driver will then hold the GPIOs to turn off the
PHY when requested (e.g. during suspend).
To fix the problem, this reverts the commit to restore the old
behavior to put the GPIOs immediately after usage.
Link: https://www.spinics.net/lists/linux-usb/msg174681.html
Cc: stable@vger.kernel.org
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The missed break statement in the outer switch makes the code fall through
always and thus always same value will be printed.
Besides that, compiler warns about missed fall through marker:
drivers/usb/dwc3/./trace.h: In function ‘trace_raw_output_dwc3_log_trb’:
drivers/usb/dwc3/./trace.h:246:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (pcm) {
^~~~~~
Add the missing break statement to work correctly without compilation
warnings.
Fixes: fa8d965d73 ("usb: dwc3: trace: pretty print high-bandwidth transfers too")
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implement the new frame_number API to report the isochronous interval
frame number. This patch checks and reports the interval in which the
isoc transfer was transmitted or received via the Isoc-First TRB SOF
number field.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Availability of TRB's is calculated using dwc3_calc_trbs_left(), which
determines total available TRB's based on the HWO bit set in a TRB.
In the present code, __dwc3_prepare_one_trb() is called with a TRB which
needs to be prepared for transfer. This __dwc3_prepare_one_trb() calls
dwc3_calc_trbs_left() to determine total available TRBs and set IOC bit
if the total available TRBs are zero. Since the present working TRB (which
is passed as an argument to __dwc3_prepare_one_trb() ) doesn't yet have
the HWO bit set before calling dwc3_calc_trbs_left(), there are chances
that dwc3_calc_trbs_left() wrongly calculates this present working TRB
as free(since the HWO bit is not yet set) and returns the total available
TRBs as greater than zero (including the present working TRB). This could
be a problem.
This patch corrects the above mentioned problem in __dwc3_prepare_one_trb()
by increementing the dep->trb_enqueue at the last (after preparing the TRB)
instead of increementing at the start and setting the IOC bit only if the
total available TRBs returned by dwc3_calc_trbs_left() is 1 . Since we are
increementing the dep->trb_enqueue at the last, the present working TRB is
also considered as available by dwc3_calc_trbs_left() and non zero value is
returned . So, according to the modified logic, when the total available
TRBs is equal to 1 that means the total available TRBs in the pool are 0.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Tested-by: Tejas Joglekar <tejas.joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The stream capable endpoints require stream id to be given
when issuing START TRANSFER. While issuing no-op trb the
stream id is not yet known, so don't issue no-op trb's on
stream capable endpoints.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For stream capable endpoints, stream id related information
needs to be updated into DEPCMD while issuing START TRANSFER.
This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget driver may take an unbounded amount of time to queue requests
after XferNotReady. This is important for isochronous endpoints which
need to be started for a specific (micro-)frame.
If we fail to start a transfer for isochronous endpoint, let's try
queueing to a future interval and see if that helps. We will stop trying
if we fail a start transfer for 5 intervals in the future.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Running out of requests on isochronous endpoints is part of normal
operation. We don't really need to know about it every time it
happens.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
They are much more useful in hexadecimal than in decimal. Moreover,
generic commands are already logged in hex.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sometimes, errors happen when kicking transfers from
__dwc3_gadget_start_isoc(). In those cases, we need to pass along the
error so gadget driver can make informed decisions.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we have a list of cancelled requests, we can skip over TRBs
when END_TRANSFER command completes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Whenever we have a request in flight, we can move it to the cancelled
list and later simply iterate over that list and skip over any TRBs we
find.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Extract the logic for skipping over TRBs to its own function. This
makes the code slightly more readable and makes it easier to move this
call to its final resting place as a following patch.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we track how many TRBs a request uses, it's easier to skip
over them in case of a call to usb_ep_dequeue(). Let's do so and
simplify the code a bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Both flags are used for the same purpose in dwc3: appending an extra
TRB at the end to deal with controller requirements. By combining both
flags into one, we make it clear that the situation is the same and
that they should be treated equally.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DWC_usb31 version 1.70a-ea06 and prior, for highspeed and fullspeed
isochronous IN, BIT[15:14] of the 16-bit microframe number reported by
the XferNotReady event are invalid. The driver uses this number to
schedule the isochronous transfer and passes it to the START TRANSFER
command. Because this number is invalid, the command may fail. If
BIT[15:14] matches the internal 16-bit microframe, the START TRANSFER
command will pass and the transfer will start at the scheduled time, if
it is off by 1, the command will still pass, but the transfer will start
2 seconds in the future. For all other conditions, the START TRANSFER
command will fail with bus-expiry.
In order to workaround this issue, we can test for the correct
combination of BIT[15:14] by sending START TRANSFER commands with
different values of BIT[15:14]: 'b00, 'b01, 'b10, and 'b11. Each
combination is 2^14 uframe apart (or 2 seconds). 4 seconds into the
future will result in a bus-expiry status. As the result, within the 4
possible combinations for BIT[15:14], there will be 2 successful and 2
failure START COMMAND status. One of the 2 successful command status
will result in a 2-second delay start. The smaller BIT[15:14] value is
the correct combination.
Since there are only 4 outcomes and the results are ordered, we can
simply test 2 START TRANSFER commands with BIT[15:14] combinations 'b00
and 'b01 to deduce the smaller successful combination.
Let test0 = test status for combination 'b00 and test1 = test status for
'b01 of BIT[15:14]. The correct combination is as follow:
if test0 fails and test1 passes, BIT[15:14] is 'b01
if test0 fails and test1 fails, BIT[15:14] is 'b10
if test0 passes and test1 fails, BIT[15:14] is 'b11
if test0 passes and test1 passes, BIT[15:14] is 'b00
Synopsys STAR 9001202023: Wrong microframe number for isochronous IN
endpoints.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a new field to dwc3 structure to track VERSIONTYPE. The VERSIONTYPE
is represented in ASCII in the 32-bit VERSIONTYPE register. In
DWC_usb31, sub releases for each version are tracked with VERSIONTYPE
such as "ea01" and "ea02".
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb31 and DWC_usb3 v3.30a and higher do not support OTG mode. If
the controller supports DRD but the dr_mode is not specified or set to
OTG, then set the mode to peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allow extcon device, found by name, to provide DR status for USB.
This is needed, for example, in case of Intel Merrifield platform,
where the Intel Basin Cove PMIC provides an extcon device to communicate
the detected role.
Note, that the "linux,extcon-name" property name is only for kernel
internal use by X86/ACPI platform code and as such is not documented
in the device tree bindings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Switch to device property for 'extcon' handling.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's not very useful to repeat a bunch of probe deferral errors. And
it's also not very useful to log "failed" without telling the error
code.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support the option to disable USB2 LPM. Set xhci "usb2-lpm-disable"
property via "snps,usb2-lpm-disable" property.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
GUSB2PHYCFG.ENBLSLPM enables the controller to assert low power signals
to the PHY. Unless disabled via device property, explicitly set
GUSB2PHYCFG.ENBLSLPM as it may not be set by default.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Current implementation only prints/sets the link state for peripheral
mode only. Check and prevent printing bogus link state if the current
mode of operation is not peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Highspeed device and below has different state names than superspeed and
higher. Add proper checks and printouts of link states for highspeed and
below.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To dump internal LSP and endpoint state debug registers, we must write
to GDBGLSPMUX register. This patch correctly dump LSP and endpoint
states from the debug registers.
If the controller is in device mode, all LSP and endpoint state
registers will be dumped via the debugfs attribute "lsp_dump". In host
mode, the user has to write the LSP number to "lsp_dump" to dump a
specific LSP selection.
Fixes: 80b776340c ("usb: dwc3: Dump LSP and BMU debug info")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
TxFIFO and RxFIFO from GDBGFIFOSPACE are fifo depths in MDWIDTH. Convert
them into bytes for easier read.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Tx/RxFIFO types in the GDBGFIFOSPACE.FIFO_QUEUE_SELECT are not
queue. Properly rename them.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit ffb80fc672.
Turns out that commit is wrong. Host controllers are allowed to use
Clear Feature HALT as means to sync data toggle between host and
periperal.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When chaining ISOC TRBs together, only the first ISOC TRB should be of
type ISOC_FIRST, all others should be of type ISOC. This patch fixes
that.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc3_pci_quirks() function, gpiod lookup table is only registered for
baytrail SOC. But in dwc3_pci_remove(), we try to unregistered it
without any checks. This leads to NULL pointer de-reference exception in
gpiod_remove_lookup_table() when unloading the module for non baytrail
SOCs. This patch fixes this issue.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms
without ACPI GPIO resources")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Current check for the last extra TRB for zero and unaligned transfers
does not account for isoc OUT. The last TRB of the Buffer Descriptor for
isoc OUT transfers will be retired with HWO=0. As a result, we won't
return early. The req->remaining will be updated to include the BUFSIZ
count of the extra TRB, and the actual number of transferred bytes
calculation will be wrong.
To fix this, check whether it's a short or zero packet and the last TRB
chain bit to return early.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If dwc3_core_init_mode() fails with deferred probe,
next probe fails on sysfs with
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:11.0/dwc3.0.auto/dwc3.0.auto.ulpi'
To avoid this failure, clean up ULPI device.
Cc: <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
'optimizations' was misspelled as 'optmizations'. Fixed it. It is a
coding style change which should have no impact on runtime execution of code.
Signed-off-by: Faisal Mehmood <f.m3hm00d@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint
command.
Current implementation only save and restore GUSB2PHYCFG.SUSPHY
configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and
GUSB2PHYCFG.SUSPHY settings. Restore them after the command is
completed.
DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Like the omap back-end, we get a link error with CONFIG_EXTCON=m
when building the qcom back-end into the kernel:
drivers/usb/dwc3/dwc3-qcom.o: In function `dwc3_qcom_probe':
dwc3-qcom.c:(.text+0x13dc): undefined reference to `extcon_get_edev_by_phandle'
dwc3-qcom.c:(.text+0x1b18): undefined reference to `devm_extcon_register_notifier'
dwc3-qcom.c:(.text+0x1b9c): undefined reference to `extcon_get_state'
Do the same thing as OMAP and add an explicit dependency on
EXTCON.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 variant found in Exynos5433 SoCs requires keeping all DRD30/UHOST30
clocks enabled all the time the driver does any access to DWC3 registers,
otherwise external abort happens. So far DWC3 hardware module worked with
samsung,exynos5250-dwusb3 compatible only by luck when built into kernel:
all DRD30 clocks were left enabled by bootloader and later kept enabled
by the DRD PHY driver. However, if one tried to use Exnos DWC3 driver as
a module or performed system suspend/resume cycle, external abort
happened. This patch finally fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add per-variant list of clocks and manage them all together in
the single array. This is a preparation for adding new variants
of Exynos SoCs. No functional changes for existing Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All supported Exynos variants provide respective generic PHY framework
based drivers for controlling USB PHYs, so there is no point
creating fake USB PHYs based on platform devices. While removing useless
code, remove calls to runtime PM, which have no effect.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
NET2280 got a fix to an old patch attempting to fix locking for gadget
framework callbacks.
DWC2 fixed a bug where driver was attempting to access registers before
clocks were enabled.
DWC3 got a fix for ULPI clock configuration on Baytrail devices.
FOTG210 plugged a memory leak and Renesas USB3 fixed ep0 maxpacket size.
-----BEGIN PGP SIGNATURE-----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=bEhk
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.19-rc2
NET2280 got a fix to an old patch attempting to fix locking for gadget
framework callbacks.
DWC2 fixed a bug where driver was attempting to access registers before
clocks were enabled.
DWC3 got a fix for ULPI clock configuration on Baytrail devices.
FOTG210 plugged a memory leak and Renesas USB3 fixed ep0 maxpacket size.
In case of error, the function pcim_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 7740d04d90 ("usb: dwc3: pci: Enable ULPI Refclk on platforms where the firmware does not")
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
An incorrect #ifdef caused a pair of harmless warnings when CONFIG_PM_SLEEP
is disabled:
drivers/usb/dwc3/dwc3-of-simple.c:223:12: error: 'dwc3_of_simple_resume' defined but not used [-Werror=unused-function]
static int dwc3_of_simple_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~
drivers/usb/dwc3/dwc3-of-simple.c:213:12: error: 'dwc3_of_simple_suspend' defined but not used [-Werror=unused-function]
static int dwc3_of_simple_suspend(struct device *dev)
Since the #ifdef method is generally hard to get right, use
a simpler __maybe_unused annotation here to let the compiler
drop the unused functions silently. This also improves
compile-time coverage.
Fixes: 76251db865 ("usb: dwc3: of-simple: reset host controller at suspend/resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
-----BEGIN PGP SIGNATURE-----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=HiNz
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.19
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
endpoint->maxpacket is not updated after setting the
usb_set_maxpacket_limit() on endpoint enable. The MaxPacketSize can be
different than the endpoint->maxpacket_limit.
DWC3 has been consistently using MaxPacketSize from the endpoint's
descriptor, so let's keep it consistent and use the MaxPacketSize from
the endpoint's descriptor instead.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By default when core sees any transaction error (CRC or overflow) it
replies with terminating retry ACK (Retry=1 and Nump == 0).
Enabling this Auto Retry feature in controller will make the core send
a non-terminanting ACK upon such transaction errors. That is, ACK TP
with Retry=1 and Nump != 0.
Doing so will give controller a chance to recover from transient error
conditions.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc_usb31 does not support OTG mode. If the controller supports DRD but
the dr_mode is not specified or set to OTG, then set the mode to
peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On Intel Edison board the OTG function is enabled, thus,
USB can switch to the host mode.
Allow that by changing dr_mode property to "otg" for Intel Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For now all PCI enumerated dwc3 devices require some properties
to be present. This allows us to unconditionally append them and supply
via driver_data.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable the undefined length INCR burst type and set INCRx.
Different platform may has the different burst size type.
In order to get best performance, we need to tune the burst
size to one special value, instead of the default value.
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add the macro definition for global soc bus configuration
register 0
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Describe 'wakeup_work' field of struct dwc3_pci to avoid a warning:
drivers/usb/dwc3/dwc3-pci.c:59: warning: Function parameter or member 'wakeup_work' not described in 'dwc3_pci'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit ff3f0789b3 ("usb: dwc3: use BIT() macro where possible")
changed DWC3_DEPCFG_STREAM_EVENT_EN from bit 13 to bit 12.
Spotted this cleanup typo while looking at diffs between 4.9.35 and
4.14.16 for a separate issue.
Fixes: ff3f0789b3 ("usb: dwc3: use BIT() macro where possible")
Signed-off-by: Erich E. Hoover <ehoover@sweptlaser.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we power off the SoC logic rail in S3, we can find that the Type-C
PHY can't initialize correctly after system resume. We need to toggle
the USB3-OTG reset before trying to initialize the PHY, or else it
times out.
phy phy-ff800000.phy.9: phy poweron failed --> -110
dwc3 fe900000.dwc3: failed to initialize core
dwc3: probe of fe900000.dwc3 failed with error -110
Note that the RK3399 TRM suggests that we should keep the whole usb3
controller in reset for the duration of the Type-C PHY initialization.
However, it's hard to assert the reset in the current framework of
reset. We're still skeptical about that, and we haven't yet found a
case where this seems to have mattered. This approach is much easier, it
simply holds the USB3-OTG reset while device is supended.
The dwc3 core is going to reinitialize the controller at suspend/resume
anyway (including a "soft reset"), so it should be safe to do this.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Even though we only use them once, it is better to not put/release
the GPIOs immediately after use, so that others cannot claim them.
Use devm functions to get the phy GPIOs, so that they will be
automatically released when were unbound from the device and
remove the gpio_put calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On some Bay Trail (BYT) systems the firmware does not enable the
ULPI Refclk.
This commit adds a helper which checks and if necessary enabled the Refclk
and calls this helper for BYT machines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Bay Trail / BYT SoCs do not have a builtin device-mode phy, instead
they require an external ULPI phy for device-mode.
Only some BYT devices have an external phy, but even on those devices
device-mode is not working because the dwc3 does not see the phy.
The problem is that the ACPI fwnode for the dwc3 does not contain the
expected GPIO resources for the GPIOs connected to the chip-select and
reset pins of the phy.
I've found the workaround which some Android x86 kernels use for this:
https://github.com/BORETS24/Kernel-for-Asus-Zenfone-2/blob/master/arch/x86/platform/intel-mid/device_libs/pci/platform_usb_otg.c
Which boils down to hardcoding the GPIOs for these devices.
The good news it that all boards (*) use the same GPIOs.
This commit fixes the ULPI phy not woring by adding a gpiod_lookup_table
call which adds a hardcoded mapping for BYT devices. Note that the mapping
added by gpiod_add_lookup_table is a fallback mapping, so boards which
properly provide GPIO resources in the ACPI firmware-node resources
will not use this.
*) Except for the first revision of the evalulation-kit, which normal users
don't have
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This driver is to be used for Synopsys PCIe-base HAPS platform. Move the
the HAPS support from dwc3-pci to this driver.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Variable maxpacket is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'maxpacket' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #ifdef guards around these are wrong, resulting in warnings
in certain configurations:
drivers/usb/dwc3/dwc3-qcom.c:244:12: error: 'dwc3_qcom_resume' defined but not used [-Werror=unused-function]
static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
^~~~~~~~~~~~~~~~
drivers/usb/dwc3/dwc3-qcom.c:223:12: error: 'dwc3_qcom_suspend' defined but not used [-Werror=unused-function]
static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
This replaces the guards with __maybe_unused annotations to shut up
the warnings and give better compile time coverage.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix to return error code -ENODEV from the get device failed error
handling case instead of 0, as done elsewhere in this function.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit fe8abf332b ("usb: dwc3: support clocks and resets for DWC3 core")
adds support for handling clocks and resets in the DWC3 core, so that for
platforms following the standard devicetree bindings this does not need
to be duplicated in all the different glue layers.
These changes intended for devicetree based platforms introduce an
uncoditional clk_bulk_get() in the core probe path. This leads to the
following error being logged on x86/ACPI systems:
[ 26.276783] dwc3 dwc3.3.auto: Failed to get clk 'ref': -2
This commits wraps the clk_bulk_get() in an if (dev->of_node) check so
that it only is done on devicetree instantiated devices, fixing this
error.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The clocks have already been explicitly disabled and put as part of
remove() so the runtime suspend callback must not be run when balancing
the runtime PM usage count before returning.
Fixes: 16adc674d0 ("usb: dwc3: add generic OF glue layer")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that a "#define DEBUG" was left in on the recent patch
landed for the Qualcomm DWC3 glue driver. Let's remove it.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc3_ep_dequeue() waits for completion of End Transfer command using
wait_event_lock_irq(), which will release the dwc3->lock while waiting
and reacquire after completion. This allows a potential race condition
with ep_disable() which also removes all requests from started_list
and pending_list.
The check for NULL r->trb should catch this but currently it exits to
the wrong 'out1' label which calls dwc3_gadget_giveback(). Since its
list entry was already removed, if CONFIG_DEBUG_LIST is enabled a
'list_del corruption' bug is thrown since its next/prev pointers are
already LIST_POISON1/2. If r->trb is NULL it should simply exit to
'out0'.
Fixes: cf3113d893 ("usb: dwc3: gadget: properly increment dequeue pointer on ep_dequeue")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes the following sparse warning:
drivers/usb/dwc3/gadget.c:169:6: warning:
symbol 'dwc3_gadget_del_and_unmap_request' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix sparse warning
Fixes: 5f0b74e548 ("USB: dwc3: get extcon device by OF graph bindings")
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We dont' need to touch req->direction or req->epnum from
ep_queue(). It's enough that we initialize both fields from
alloc_request() and just keep them for the entire lifetime of the
request.
No functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of *always* calling dwc3_gadget_ep_get_transfer_index() after
sending a Start Transfer command, we can call it once from
dwc3_send_gadget_ep_cmd() itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of returning resource index number just to assign it to a
field inside 'dep' which was passed as argument, we can assing
dep->resource_index from inside dwc3_gadget_ep_get_transfer_index()
itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we have many started requests and one of them in the middle is
completed with Missed Isoc, let's not End Transfer as that would
result in us loosing (possibly) many more intervals.
Instead, let's allow the controller to go through its list of started
requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
XferNotReady and XferInProgress give us the uFrame number we're
currently in. Printing that out on tracepoints may help us find bugs
in transfer scheduling.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Avoid a prototype when the function can be defined earlier. No
functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of having a prototype for a function that's defined a few
lines down, let's just move definition to the place where prototype
was.
No functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In a few places, the argument is completely unnecessary. On places
where it's needed, we can get it from dep->dwc.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Those two arguments refer to a single bitfield in the register. In
order to simplify the code, we can combine them into a single argument
and expect caller to pass the correct action argument at all times.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will only have event status of IOC when IOC bit is set in
TRB. There's no need to check both bits.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We know that only OUT endpoints can trigger SHORT. We also know that
count MUST be > 0 whenever SHORT triggers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will make it easier to figure out the reason for the event. That
information really helps debugging certain problems.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We are trying to kick transfers on Isochronous endpoints in a more
controlled manner now. And this ended up rendering this piece of code
unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of having one big loop, let's split it down into two smaller
handlers: one for linear buffers and one for scatterlist.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After all the previous changes, it's now a lot clearer how isoc
transfers should be managed. We don't need to try to End Transfers
from ep_queue since that's already done by cleanup_requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now, this part of the code is duplicated and brings no extra value to
the driver. Let's remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we get an event with status set to Missed Isoc, this means we
have missed an isochronous interval and should issue End Transfer
command and wait for the following XferNotReady.
Let's do that early, rather than late.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By now, it has the same semantics as DWC3_EP_TRANSFER_STARTED, but
that has a much more descriptive name.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will need an up-to-date frame_number from XferInProgress too when
future patches improve our handling of Isoc endpoints.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The core requires the extra two bits of information for properly
scheduling Isochronous transfers. This means that we can't rely on
__dwc3_gadget_get_frame(). Let's always cache uFrame number from
XferNotReady instead.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Endpoint handlers need to know about endpoints, not dwc. If they
really need access to dwc (e.g. for printing error messages) we have a
reference to it tucked inside the endpoint.
This patch has no functional changes, it's simply moving things around.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We *KNOW* which events we enable for which endpoint types and
we *KNOW* when they'll trigger. The endpoint type checks are
pointless.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch simply renames two functions to more descriptive names so
that it's easier to understand what they're doing.
Cleanup only, no functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of constantly calling kick transfer everything some event
shows up, let's just rely on the fact that we send Update Transfer
every time a new request is queued.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we're making sure we don't have XferComplete events, we can
rename this function to what it actually handles:
dwc3_gadget_endpoint_transfer_in_progress()
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
XferComplete is enabled only for the default control pipe, let's make
that clear in the code.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't use XferNotReady for anything other than Default Control
Pipe, which is handled in ep0.c, and Isochronous endpoints. Let's make
that clear in the code.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Interrupt endpoints behave much like Bulk endpoints with the exception
that they are periodic. We can pre-issue Start Transfer exactly as we
do for Bulk endpoints.
While at that, remove one trailing blank line which is unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The present code correctly fetches the req which were previously not
queued from the started_list but fails to continue queuing from the sg
where it previously stopped queuing (because of the unavailable TRB's).
This patch correct's the code to continue queuing from the correct sg
present in the sglist.
For example, consider 5 sgs in req. Because of limited TRB's among the
5 sgs only 3 got queued. This patch corrects the code to start queuing
from correct sg i.e 4th sg when the TRBs are available.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The code logic in dwc3_prepare_one_trb() incorrectly uses the address
and length fields present in req packet for mapping TRB's instead of
using the address and length fields of scattergather lists. This patch
correct's the code to use sg->address and sg->length when scattergather
lists are present.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
extcon device is used to detect host/device connection. Since extcon
OF property is deprecated, alternative method should be added.
This method uses OF graph bindings to locate extcon.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Historically, the clocks and resets are handled on the glue layer
side instead of the DWC3 core. For simple cases, dwc3-of-simple.c
takes care of arbitrary number of clocks and resets. The DT node
structure typically looks like as follows:
dwc3-glue {
compatible = "foo,dwc3";
clocks = ...;
resets = ...;
...
dwc3 {
compatible = "snps,dwc3";
...
};
}
By supporting the clocks and the reset in the dwc3/core.c, it will
be turned into a single node:
dwc3 {
compatible = "foo,dwc3", "snps,dwc3";
clocks = ...;
resets = ...;
...
}
This commit adds the binding of clocks and resets specific to this IP.
The number of clocks should generally be the same across SoCs, it is
just some SoCs either tie clocks together or do not provide software
control of some of the clocks.
I took the clock names from the Synopsys datasheet: "ref" (ref_clk),
"bus_early" (bus_clk_early), and "suspend" (suspend_clk).
I found only one reset line in the datasheet, hence the reset-names
property is omitted.
Those clocks are required for new platforms. Enforcing the new
binding breaks existing platforms since they specify clocks (and
resets) in their glue layer node, but nothing in the core node.
I listed such exceptional cases in the DT binding. The driver
code has been relaxed to accept no clock. This change is based
on the discussion [1].
I inserted reset_control_deassert() and clk_bulk_enable() before the
first register access, i.e. dwc3_cache_hwparams().
[1] https://patchwork.kernel.org/patch/10284265/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It is not a good idea to directly modify the resource of a platform
device. Modify its local copy, and pass it to devm_ioremap_resource()
so that we do not need to restore it in the failure path and the remove
hook.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some PHY drivers (e.g. for Qualcomm QUSB2 and QMP PHYs) support
runtime PM to reduce PHY power consumption during bus_suspend.
Add changes to let core auto-suspend PHYs on host bus-suspend
using GUSB2PHYCFG register if needed for a platform. Also perform
PHYs runtime suspend/resume and let platform glue drivers e.g.
dwc3-qcom handle remote wakeup during bus suspend by waking up
devices on receiving wakeup event from PHY.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 controller on Qualcomm SOCs has a Qscratch wrapper.
Some of its uses are described below resulting in need to
have a separate glue driver instead of using dwc3-of-simple:
- It exposes register interface to override vbus-override
and lane0-pwr-present signals going to hardware. These
must be updated in peripheral mode for DWC3 if vbus lines
are not connected to hardware block. Otherwise RX termination
in SS mode or DP pull-up is not applied by device controller.
- pwr_events_irq_stat support to check if USB2 PHY is in L2 state
before glue driver proceeds with suspend.
- Support for wakeup interrupts lines that are asserted whenever
there is any wakeup event on USB3 or USB2 bus.
- Support to replace pip3 clock going to DWC3 with utmi clock
for hardware configuration where SSPHY is not used with DWC3.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add compatible string to use this generic glue layer to support
Allwinner H6 platform's dwc3 controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is a requirement which has always existed but, somehow, wasn't
reflected in the documentation and problems weren't found until now
when Tuba Yavuz found a possible deadlock happening between dwc3 and
f_hid. She described the situation as follows:
spin_lock_irqsave(&hidg->write_spinlock, flags); // first acquire
/* we our function has been disabled by host */
if (!hidg->req) {
free_ep_req(hidg->in_ep, hidg->req);
goto try_again;
}
[...]
status = usb_ep_queue(hidg->in_ep, hidg->req, GFP_ATOMIC);
=>
[...]
=> usb_gadget_giveback_request
=>
f_hidg_req_complete
=>
spin_lock_irqsave(&hidg->write_spinlock, flags); // second acquire
Note that this happens because dwc3 would call ->complete() on a
failed usb_ep_queue() due to failed Start Transfer command. This is,
anyway, a theoretical situation because dwc3 currently uses "No
Response Update Transfer" command for Bulk and Interrupt endpoints.
It's still good to make this case impossible to happen even if the "No
Reponse Update Transfer" command is changed.
Reported-by: Tuba Yavuz <tuba@ece.ufl.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quite a lot happened in this cycle, with a total of 95 non-merge
commits. The most interesting parts are listed below:
Synopsys has been adding better support for USB 3.1 to dwc3. The same
series also sets g_mass_storage's max speed to SSP.
Roger Quadros (TI) added support for dual-role using the OTG block
available in some dwc3 implementations, this makes sure that AM437x
can swap roles in runtime.
We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to
the work of Martin Blumenstingl.
We also have a ton of changes in dwc2 (51% of all changes, in
fact). The most interesting part there is the support for
Hibernation (a Synopsys PM feature).
Apart from these, we have our regular set of non-critical fixes all
over the place.
-----BEGIN PGP SIGNATURE-----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=F6OC
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: changes for v4.17 merge window
Quite a lot happened in this cycle, with a total of 95 non-merge
commits. The most interesting parts are listed below:
Synopsys has been adding better support for USB 3.1 to dwc3. The same
series also sets g_mass_storage's max speed to SSP.
Roger Quadros (TI) added support for dual-role using the OTG block
available in some dwc3 implementations, this makes sure that AM437x
can swap roles in runtime.
We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to
the work of Martin Blumenstingl.
We also have a ton of changes in dwc2 (51% of all changes, in
fact). The most interesting part there is the support for
Hibernation (a Synopsys PM feature).
Apart from these, we have our regular set of non-critical fixes all
over the place.
On TI's AM437x, the DWC3 controller looses state after a
system suspend/resume. We are re-initializing the controller
but we miss restoring the PRTCAP register. This causes
USB host to break on AM437x after a system suspend/resume.
Fix this by restoring the PRTCAP register on system resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb3 speed can only be set up to SuperSpeed. Limit the setting to
SuperSpeed only should the value be higher. Otherwise, the controller
will read an invalid speed value and set the device to an incorrect
speed.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check and configure TX/RX threshold for DWC_usb31. Update dwc3 structure
with new fields to store these threshold configurations.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb31 controller has a different UsbRxPktCnt bit fields from
GRXTHRCFG register. Check for DWC_usb31 IP revision to read the
appropriate value.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb31 controller has different GTXFIFOSIZE bit field for TXFDEF.
Check for DWC_usb31 IP revision to read the appropriate bit fields.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Update two GTXFIFOSIZ bit fields for the DWC_usb31 controller. TXFDEP
is a 15-bit value instead of 16-bit value, and bit 15 is TXFRAMNUM.
The GTXFIFOSIZ register for DWC_usb31 is as follows:
+-------+-----------+----------------------------------+
| BITS | Name | Description |
+=======+===========+==================================+
| 31:16 | TXFSTADDR | Transmit FIFOn RAM Start Address |
| 15 | TXFRAMNUM | Asynchronous/Periodic TXFIFO |
| 14:0 | TXFDEP | TXFIFO Depth |
+-------+-----------+----------------------------------+
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
From DWC_usb31 programming guide section 1.3.2, once DWC3_DCTL_CSFTRST
bit is cleared, we must wait at least 50ms before accessing the PHY
domain (synchronization delay).
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Platform device is allocated before adding resources. Make sure to
properly cleanup on error case.
Cc: <stable@vger.kernel.org>
Fixes: f1c7e71081 ("usb: dwc3: convert to pcim_enable_device()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If building a kernel without FTRACE but with TRACING, dwc3.ko fails to
link due to missing trace events. Fix this by using the correct
Kconfig symbol on Makefile.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In
dwc3_request *r = NULL;
r = A;
the first assignment has no effect. Remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the following test we get stuck by sleeping forever in _dwc3_set_mode()
after which dual-role switching doesn't work.
On dra7-evm's dual-role port,
- Load g_zero gadget driver and enumerate to host
- suspend to mem
- disconnect USB cable to host and connect otg cable with Pen drive in it.
- resume system
- we sleep indefinitely in _dwc3_set_mode due to.
dwc3_gadget_exit()->usb_del_gadget_udc()->udc_stop()->
dwc3_gadget_stop()->wait_event_lock_irq()
To fix this instead of waiting indefinitely with wait_event_lock_irq()
we use wait_event_interruptible_lock_irq_timeout() and print
and error message if there was a timeout.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is useful on platforms (e.g. TI AM437x) that don't
have ID available on a GPIO but do have the OTG block.
We can obtain the ID state via the OTG block and use it
for dual-role switching.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't support PRTCAP == OTG yet, so prevent user from
setting it via debugfs.
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Amlogic Meson GXL and AXG SoCs come with a (host-only) dwc3 USB
controller. To use this controller a clock has to be enabled and a reset
line has to be pulsed.
Enabling the clock works identical to other SoCs. However, the reset
line has to be pulsed (using reset_control_reset) instead of using a
level reset (reset_control_{assert,deassert}).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some SoCs (such as Amlogic Meson GXL for example) share the reset line
with other components (in case of the Meson GXL example there's a shared
reset line between the USB2 PHYs, USB3 PHYs and the dwc3 controller).
Additionally SoC implementations may prefer a reset pulse over level
resets.
For now this falls back to the old defaults, which are:
- reset lines are exclusive
- level resets are being used
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To reproduce the lock up do the following
- connect otg host adapter and a USB device to the dual-role port
so that it is in host mode.
- suspend to mem.
- disconnect otg adapter.
- resume the system.
If we call dwc3_host_exit() before tasks are thawed
xhci_plat_remove() seems to lock up at the second usb_remove_hcd() call.
To work around this we queue the _dwc3_set_mode() work on
the system_freezable_wq.
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: <stable@vger.kernel.org> # v4.12+
Suggested-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In order for ULPI PHYs to work, dwc3_phy_setup() and dwc3_ulpi_init()
must be doene before dwc3_core_get_phy().
commit 541768b08a ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
broke this.
The other issue is that dwc3_core_get_phy() and dwc3_ulpi_init() should
be called only once during the life cycle of the driver. However,
as dwc3_core_init() is called during system suspend/resume it will
result in multiple calls to dwc3_core_get_phy() and dwc3_ulpi_init()
which is wrong.
Fix this by moving dwc3_ulpi_init() out of dwc3_phy_setup()
into dwc3_core_ulpi_init(). Use a flag 'ulpi_ready' to ensure that
dwc3_core_ulpi_init() is called only once from dwc3_core_init().
Use another flag 'phys_ready' to call dwc3_core_get_phy() only once from
dwc3_core_init().
Fixes: 541768b08a ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
Fixes: f54edb539c ("usb: dwc3: core: initialize ULPI before trying to get the PHY")
Cc: linux-stable <stable@vger.kernel.org> # >= v4.13
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The FIFO/Queue type values are incorrect. Correct them according to
DWC_usb3 programming guide section 1.2.27 (or DWC_usb31 section 1.2.25).
Additionally, this patch includes ProtocolStatusQ and AuxEventQ types.
Fixes: cf6d867d3b ("usb: dwc3: core: add fifo space helper")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The USB cable state can change during suspend/resume
so be sure to check and update the extcon state.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 689bf72c6e ("usb: dwc3: Don't reinitialize core during
host bus-suspend/resume") updated suspend/resume routines to not
power_off and reinit PHYs/core for host mode.
It broke platforms that rely on DWC3 core to power_off PHYs to
enter low power state on system suspend.
Perform dwc3_core_exit/init only during host mode system_suspend/
resume to addresses power regression from above mentioned patch
and also allow USB session to stay connected across
runtime_suspend/resume in host mode. While at it also replace
existing checks for HOST only dr_mode with current_dr_role to
have similar core driver behavior for both Host-only and DRD+Host
configurations.
Fixes: 689bf72c6e ("usb: dwc3: Don't reinitialize core during host bus-suspend/resume")
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In this function, we init the USB2 and USB3 PHYs, but if soft reset
times out, we don't unwind this.
Noticed by inspection.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 tracks TRB counter for each ep0 direction separately. In control
read transfer completion handler, the driver needs to reset the TRB
enqueue counter for ep0 IN direction. Currently the driver only resets
the TRB counter for control OUT endpoint. Check for the data direction
and properly reset the TRB counter from correct control endpoint.
Cc: stable@vger.kernel.org
Fixes: c2da2ff006 ("usb: dwc3: ep0: don't use ep0in for transfers")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There are 2 control endpoint structures for DWC3. However, the driver
only updates the OUT direction control endpoint structure during
ConnectDone event. DWC3 driver needs to update the endpoint max packet
size for control IN endpoint as well. If the max packet size is not
properly set, then the driver will incorrectly calculate the data
transfer size and fail to send ZLP for HS/FS 3-stage control read
transfer.
The fix is simply to update the max packet size for the ep0 IN direction
during ConnectDone event.
Cc: stable@vger.kernel.org
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_of_simple_dev_pm_ops has never been used since commit a0d8c4cfdf
("usb: dwc3: of-simple: set dev_pm_ops"), but this commit has brought
and oops when unbind the device due this sequence:
dwc3_of_simple_remove
-> clk_disable ...
-> pm_runtime_put_sync
-> dwc3_of_simple_runtime_suspend
-> clk_disable (again)
This double call to clk_core_disable causes a kernel oops like this:
WARNING: CPU: 1 PID: 4022 at drivers/clk/clk.c:656 clk_core_disable+0x78/0x80
CPU: 1 PID: 4022 Comm: bash Not tainted 4.15.0-rc4+ #44
Hardware name: Google Kevin (DT)
pstate: 80000085 (Nzcv daIf -PAN -UAO)
pc : clk_core_disable+0x78/0x80
lr : clk_core_disable_lock+0x20/0x38
sp : ffff00000bbf3a90
...
Call trace:
clk_core_disable+0x78/0x80
clk_disable+0x1c/0x30
dwc3_of_simple_runtime_suspend+0x30/0x50
pm_generic_runtime_suspend+0x28/0x40
This patch fixes the unbalanced clk disable call by setting the num_clocks
variable to zero once the clocks were disabled.
Fixes: a0d8c4cfdf ("usb: dwc3: of-simple: set dev_pm_ops")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
*) Fix in exynos5-usbdrd to enumerate SuperSpeed devices on Odroid XU3
*) Fix in Broadcom USB PHY to get Dell Low Speed keyboards working
*) Fix in Broadcom USB PHY to power down the PHY when XHCI disabled
to save power
*) Fix in Broadcom USB PHY to prevent abort in DRD mode
*) Fix in Broadcom USB PHY to use the correct dt properties
*) Fix in Mediatek PHY to detect device connection
*) Make getting resource optional for Mediatek V1 TPHY
*) Cleanup in Mediatek PHY
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=f9so
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.16
*) Fix in exynos5-usbdrd to enumerate SuperSpeed devices on Odroid XU3
*) Fix in Broadcom USB PHY to get Dell Low Speed keyboards working
*) Fix in Broadcom USB PHY to power down the PHY when XHCI disabled
to save power
*) Fix in Broadcom USB PHY to prevent abort in DRD mode
*) Fix in Broadcom USB PHY to use the correct dt properties
*) Fix in Mediatek PHY to detect device connection
*) Make getting resource optional for Mediatek V1 TPHY
*) Cleanup in Mediatek PHY
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Not many changes here, the most important being an improvement for TI's
AM57xx and DRA7xx devices which allows them to disable a metastability
workaround in situations where we know what's going on.
Other than that, we have a set of changes on Renesas UDC to make the
code a little easier to read and maintain while also better supporting
extcon framework.
The u_serial adaptation layer learned to use kfifo instead of cooking
its own FIFO implementation.
DWC3 learned to decode a few more USB requests on the trace output.
-----BEGIN PGP SIGNATURE-----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=uwh/
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.16 merge window
Not many changes here, the most important being an improvement for TI's
AM57xx and DRA7xx devices which allows them to disable a metastability
workaround in situations where we know what's going on.
Other than that, we have a set of changes on Renesas UDC to make the
code a little easier to read and maintain while also better supporting
extcon framework.
The u_serial adaptation layer learned to use kfifo instead of cooking
its own FIFO implementation.
DWC3 learned to decode a few more USB requests on the trace output.
Adding phy calibration sequence for USB 3.0 DRD PHY present on
Exynos5420/5800 systems.
This calibration facilitates setting certain PHY parameters viz.
the Loss-of-Signal (LOS) Detector Threshold Level, as well as
Tx-Vboost-Level for Super-Speed operations.
Additionally we also set proper time to wait for RxDetect measurement,
for desired PHY reference clock, so as to solve issue with enumeration
of few USB 3.0 devices, like Samsung SUM-TSB16S 3.0 USB drive
on the controller.
We are using CR_port for this purpose to send required data
to override the LOS values.
On testing with USB 3.0 devices on USB 3.0 port present on
SMDK5420, and peach-pit boards should see following message:
usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
and without this patch, should see below shown message:
usb 1-1: new high-speed USB device number 2 using xhci-hcd
[Also removed unnecessary extra lines in the register macro definitions]
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
[adapted to use phy_calibrate as entry point]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some platforms (e.g. TI's DRA7 USB2 instance) have more trouble
with the metastability workaround as it supports only
a High-Speed PHY and the PHY can enter into an Erratic state [1]
when the controller is set in SuperSpeed mode as part of
the metastability workaround.
This causes upto 2 seconds delay in enumeration on DRA7's USB2
instance in gadget mode.
If these platforms can be better off without the workaround,
provide a device tree property to suggest that so the workaround
is avoided.
[1] Device mode enumeration trace showing PHY Erratic Error.
irq/90-dwc3-969 [000] d... 52.323145: dwc3_event: event (00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.560646: dwc3_event: event (00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.798144: dwc3_event: event (00000901): Erratic Error [U0]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes the following warnings:
drivers/usb/dwc3/io.h:43:31: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/dwc3/io.h:43:31: expected void *base
drivers/usb/dwc3/io.h:43:31: got void [noderef] <asn:2>*
drivers/usb/dwc3/io.h:62:32: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/dwc3/io.h:62:32: expected void *base
drivers/usb/dwc3/io.h:62:32: got void [noderef] <asn:2>*
This fixes the noisiest ones as they get emitted multiple times.
A few warnings remain, for which the proper fix is less clear.
No behaviour change is expected.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of keeping our own isoch_delay, let's make use of the newly
introduced isoch_delay member in struct usb_gadget. The benefit here
is that we would be using a generic "API" which other UDCs can use,
resulting in a common setup for gadget drivers who may be interested
in Isoch Delay value.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For isochronous endpoints with ep->mult less than 3, PCM1 value of
trb->size in set incorrectly.
For ep->mult = 2, this is set to 0/-1 and for ep->mult = 1, this is
set to -2. This is because the initial mult is set to ep->mult - 1
instead of 2.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_of_simple_dev_pm_ops has never been used since the initial support
by commit 16adc674d0 ("usb: dwc3: add generic OF glue layer").
I guess it just missed to set .pm struct member.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If of_clk_get() fails, the clean-up of already initialized clocks should be
the same as when clk_prepare_enable() fails. Thus a clk_disable_unprepare()
for each clock should be called before the clk_put().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 16adc674d0 ("usb: dwc3: ep0: fix setup_packet_pending initialization")
Signed-off-by: Andreas Platschek <andreas.platschek@opentech.at>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver currently notifies only USB2 PHY on USB mode change.
Extend this to USB3 PHY so that PHY drivers based on the
mode can release system resources - clocks, regulators etc.
Additionally Qualcomm QMP and QUSB2 PHY drivers need to
override VBUS signal in PHY wrapper in device mode as USB
VBUS line is not connected to PHYs. Also, remove NULL checks
for PHY when calling phy_set_mode as PHY ops already check this.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Driver currently resumes and increments pm usage_count
of its child device (dwc3 main) from its runtime_resume
handler. This requires dwc3 runtime_resume to perform
pm_runtime_put to decrement the pm usage_count. However
runtime_put from dwc3 happens for non pci drivers
(e.g. dwc3-if-simple.c) as well which results in dwc3
pm usage_count becoming negative after couple of
runtime suspend resume iterations. Fix this by
performing runtime_get/put from dwc3-pci driver only
using workqueue.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Driver powers-off PHYs and reinitializes DWC3 core and gadget on
resume. While this works fine for gadget mode but in host
mode there is not re-initialization of host stack. Also, resetting
bus as part of bus_suspend/resume is not correct which could affect
(or disconnect) connected devices.
Fix this by not reinitializing core on suspend/resume in host mode
for HOST only and OTG/drd configurations.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add support to get a list of resets available for the device.
These resets must be kept de-asserted until the device is
in use.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
[p.zabel@pengutronix.de: switch to hidden reset control array]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move clock handling after of_platform_depopulate to achieve
a sequence that is reverse of the probe sequence.
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Many variables in ep0 are set but never used, so should be removed.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that all the information we need sits in struct dwc3_ep, we can
start taking only a pointer to struct dwc3_ep as an argument. This
allows us to clean the code up a bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is more possibility for sharing code if we just realise that now
__dwc3_gadget_kic_transfer() knows to break out early if there are no
TRBs left.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will let us call __dwc3_gadget_kick_transfer()
unconditionally. No functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add compatible string to use this generic glue layer to support
Spreadtrum SC9860 platform's dwc3 controller.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we don't assign a TRB to ep0 requests, we won't be able to unmap
the request later on resulting in starvation of DMA resources.
Fixes: 4a71fcb8ac ("usb: dwc3: gadget: only unmap requests from DMA if mapped")
Reported-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Not a big pull request this time around. Only 49 non-merge
commits. This pull request is, however, all over the place. Most of
the changes are in the bdc driver adding support for USB Phy layer and
PM.
Renesas adds support for R-Car H3 ES2.0 and R-Car M3-W SoCs.
Also here is PM_RUNTIME support for dwc3-keystone.
UDC Core got a DMA unmap fix to make sure we only unmap requests that
were, indeed, mapped.
Other than these, we have a lot of cleanups, many of them adding
'const' to several places.
-----BEGIN PGP SIGNATURE-----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=FSil
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.14 merge window
Not a big pull request this time around. Only 49 non-merge
commits. This pull request is, however, all over the place. Most of
the changes are in the bdc driver adding support for USB Phy layer and
PM.
Renesas adds support for R-Car H3 ES2.0 and R-Car M3-W SoCs.
Also here is PM_RUNTIME support for dwc3-keystone.
UDC Core got a DMA unmap fix to make sure we only unmap requests that
were, indeed, mapped.
Other than these, we have a lot of cleanups, many of them adding
'const' to several places.
The header clk-provider.h is there for clock drivers (providers) to
include, not client drivers (consumers). That said,
of_clk_get_parent_count() is a helper function for clock providers, not
a clk API for consumers.
Let's replace of_clk_get_parent_count() with of_count_phandle_with_args()
call, so that we can remove the include of clk-provider.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dev_pm_ops is not supposed to change at runtime. Marking it
constant.
Signed-off-by: Doug Wilson <doug.wilson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For 66AK2Gx there is a requirement to use PM Runtime to properly manage
clocks and the power domains. Therefore, add PM runtime support. Remove
legacy clock api's calls since other users of this driver worked without
these clock apis calls.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
platform_get_irq() returns an error code, but the dwc3-omap driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dev_pm_ops is not supposed to change at runtime. Marking it constant.
Signed-off-by: Doug Wilson <doug.wilson@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The PIDs for Isochronous data transfers are incorrect
for high bandwidth IN endpoints when the request length
is less than EP wMaxPacketSize.
As per spec correct PIDs for ISOC data transfers are:
1) For request length <= maxpacket
- DATA0,
2) For maxpacket < length <= (2 * maxpacket)
- DATA1, DATA0
3) For (2 * maxpacket) < length <= (3 * maxpacket)
- DATA2, DATA1, DATA0.
But driver always sets PCM fields based on wMaxPacketSize
due to which DATA2 happens even for small requests.
Fix this by setting the PCM field of trb->size depending
on request length rather than fixing it to the value
depending on wMaxPacketSize.
Ideally it shouldn't give any issues as dwc3 will send
0-length packet for next IN token if host sends (even
after receiving a short packet). Windows seems to ignore
this but with MacOS frame loss observed when using f_uvc.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A recent optimization was made so that a request put on the
pending_list wouldn't get mapped for DMA until just before
preparing a TRB for it. However, this poses a problem in case
the request is dequeued or the endpoint is disabled before the
mapping is done as that would lead to dwc3_gadget_giveback()
unconditionally calling usb_gadget_unmap_request_for_dev() with
an invalid request->dma handle. Depending on the platform's DMA
implementation the unmap operation could result in a panic.
Since we know a successful mapping is a prerequisite for getting
a TRB, the unmap can be conditionally called only when req->trb
is non-NULL.
Fixes: cdb55b39fa ("usb: dwc3: gadget: lazily map requests for DMA")
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
IRQ_NOAUTOEN cannot be used with shared IRQs, since commit 04c848d398
("genirq: Warn when IRQ_NOAUTOEN is used with shared interrupts") and
kernel now throws a warn dump. But OMAP DWC3 driver uses this flag. As
per commit 12a7f17fac ("usb: dwc3: omap: fix race of pm runtime with
irq handler in probe") that introduced this flag, PM runtime can race
with IRQ handler when deferred probing happens due to extcon,
therefore IRQ_NOAUTOEN needs to be set so that irq is not enabled until
extcon is registered.
Remove setting of IRQ_NOAUTOEN and move the registration of
shared irq to a point after dwc3_omap_extcon_register() and
of_platform_populate(). This avoids possibility of probe deferring and
above said race condition.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit f54edb539c ("usb: dwc3: core: initialize ULPI before trying to
get the PHY") moved call to dwc3_core_get_phy() from dwc3_probe() to
dwc3_core_init() after dwc3_core_soft_reset(). But
dwc3_core_soft_reset() calls phy_init(), therefore dwc3_core_get_phy()
needs to be called before dwc3_core_soft_reset().
Fix this by moving call to dwc3_core_get_phy() before
dwc3_core_soft_reset().
This fixes the following abort seen on DRA7xx platforms
[ 24.769118] usb usb2: SerialNumber: xhci-hcd.1.auto
[ 24.781144] hub 2-0:1.0: USB hub found
[ 24.787836] hub 2-0:1.0: 1 port detected
[ 24.809939] Unhandled fault: imprecise external abort (0x1406) at 0x00000000
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for
the Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that
can wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which
allows the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of
RCU which doesn't allow sleeping in the read-side critical
sections, but which in turn is expected to be allowed by the
IRQ bus locking infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance"
P-state selection algorithm is in use by making it avoid
registering scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in
intel_pstate by changing the values that correspond to
different symbolic hint names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1
on AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the
imx6q driver and clean up the sfi, exynos5440 and intel_pstate
drivers (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila,
Rafael Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski,
Mikko Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix
a minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Wsph
-----END PGP SIGNATURE-----
Merge tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The big ticket items here are the rework of suspend-to-idle in order
to add proper support for power button wakeup from it on recent Dell
laptops and the rework of interfaces exporting the current CPU
frequency on x86.
In addition to that, support for a few new pieces of hardware is
added, the PCI/ACPI device wakeup infrastructure is simplified
significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
bus locking infrastructure.
Also, there are some functional improvements for intel_pstate, tools
updates and small fixes and cleanups all over.
Specifics:
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for the
Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that can
wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which allows
the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of RCU
which doesn't allow sleeping in the read-side critical sections,
but which in turn is expected to be allowed by the IRQ bus locking
infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance" P-state
selection algorithm is in use by making it avoid registering
scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in intel_pstate
by changing the values that correspond to different symbolic hint
names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
driver and clean up the sfi, exynos5440 and intel_pstate drivers
(Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski)"
* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
PM: hibernate: constify attribute_group structures.
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
PM / Domains: Fix missing default_power_down_ok comment
PM / Domains: Fix unsafe iteration over modified list of domains
PM / Domains: Fix unsafe iteration over modified list of domain providers
PM / Domains: Fix unsafe iteration over modified list of device links
PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
PM / Domains: Call driver's noirq callbacks
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
PM / QoS: constify *_attribute_group.
PM / AVS: rockchip-io: add io selectors and supplies for rk3228
powercap/RAPL: prevent overridding bits outside of the mask
PM / sysfs: Constify attribute groups
...
Here is the big patchset of USB and PHY driver updates for 4.13-rc1.
On the PHY side, they decided to move files around to "make things
easier" in their tree. Hopefully that wasn't a mistake, but in
linux-next testing, we haven't had any reported problems.
There's the usual set of gadget and xhci and musb updates in here as
well, along with a number of smaller updates for a raft of different USB
drivers. Full details in the shortlog, nothing really major.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpavQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymJrgCgp8Pso8bs+bnIknUSQFSguWd3wM0AnA8X3NHf
lrdCuqw+2oxGOQrecacz
=5L4Q
-----END PGP SIGNATURE-----
Merge tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big patchset of USB and PHY driver updates for 4.13-rc1.
On the PHY side, they decided to move files around to "make things
easier" in their tree. Hopefully that wasn't a mistake, but in
linux-next testing, we haven't had any reported problems.
There's the usual set of gadget and xhci and musb updates in here as
well, along with a number of smaller updates for a raft of different
USB drivers. Full details in the shortlog, nothing really major.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (173 commits)
Add USB quirk for HVR-950q to avoid intermittent device resets
USB hub_probe: rework ugly goto-into-compound-statement
usb: host: ohci-pxa27x: Handle return value of clk_prepare_enable
USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
usbip: Fix uninitialized variable bug in vhci
usb: core: read USB ports from DT in the usbport LED trigger driver
dt-bindings: leds: document new trigger-sources property
usb: typec: ucsi: Add ACPI driver
usb: typec: Add support for UCSI interface
usb: musb: compress return logic into one line
USB: serial: propagate late probe errors
USB: serial: refactor port endpoint setup
usb: musb: tusb6010_omap: Convert to DMAengine API
ARM: OMAP2+: DMA: Add slave map entries for 24xx external request lines
usb: musb: tusb6010: Handle DMA TX completion in DMA callback as well
usb: musb: tusb6010_omap: Allocate DMA channels upfront
usb: musb: tusb6010_omap: Create new struct for DMA data/parameters
usb: musb: tusb6010_omap: Use one musb_ep_select call in tusb_omap_dma_program
usb: musb: tusb6010: Add MUSB_G_NO_SKB_RESERVE to quirks
usb: musb: Add quirk to avoid skb reserve in gadget mode
...
The run_wake flag in struct dev_pm_info is used to indicate whether
or not the device is capable of generating remote wakeup signals at
run time (or in the system working state), but the distinction
between runtime remote wakeup and system wakeup signaling has always
been rather artificial. The only practical reason for it to exist
at the core level was that ACPI and PCI treated those two cases
differently, but that's not the case any more after recent changes.
For this reason, get rid of the run_wake flag and, when applicable,
use device_set_wakeup_capable() and device_can_wakeup() instead of
device_set_run_wake() and device_run_wake(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
-----BEGIN PGP SIGNATURE-----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=v6a5
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: changes for v4.13 merge window
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
clk_prepare_enable() can fail here and we must check its return value.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The commit 47d3946ea2
usb: dwc3: refactor gadget endpoint count calculation
refactored dwc3_gadget_init_endpoints() and in particular changed in or
out endpoint numbering to be through. It's not always convenient and
makes code a slightly harder to read.
Introduce a new temporary variable to make it easier to understand what
is going on inside the function.
While doing that, rename local variables as follows:
u8 num -> u8 total
int num -> int kbytes
Replace implicit direction check via epnum with explicit use of
direction variable.
While here, replace %d to %u when compounding endpoint name since we are
using unsigned type.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If don't reorder initialization like this, we will never be able to
get a reference to ULPI PHYs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If PHY is suspended by the time we want to issue ULPI transfers, we
will observe timeouts on the ULPI interface. In order to avoid such
issue, let's make sure PHY is resumed before issuing a ULPI transfer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use this method to make sure we don't try to connect on speeds not
supported by the gadget driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Instead, we can require caller to pass a buffer for the function to
use. This cleans things quite a bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of going for a 512 byte buffer and using snprintf(), let's
rely on helps __string() and __assign_str() where possible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of printing out enqueue and dequeue pointer value as a header
to the output, let's mark the TRBs in question with 'E' and 'D'. The
output looks slightly easier to read.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
%p will leak kernel pointers, so let's not expose the information on
dmesg and instead use %pK. %pK will only show the actual addresses if
explicitly enabled under /proc/sys/kernel/kptr_restrict.
Cc: <stable@vger.kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.
When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).
On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some functions might want to have very, very long request queues. We
can't make any assumptions about how many requests we *are* able to
map, so instead of mapping requests early, let's map them late. This
way, functions can queue as many requests as they'd like but we won't
take DMA resources until they are needed.
Also, we can now stop processing requests when we run out of DMA
resources but still keep requests in the queue for late processing.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't need a big fat warning with stack dump at all. Running out of
TRBs is a normal condition and we will have more TRBs available as
soon as some transfers complete.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Function devm_clk_get() returns an ERR_PTR when it fails. However, in
function kdwc3_probe(), its return value is not checked, which may
result in a bad memory access bug. This patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc3 driver can overwite its previous events if its top-half IRQ
handler (TH) gets invoked again before processing the events in the
cache. We see this as a hang in the file transfer and the host will
attempt to reset the device. TH gets the event count and deasserts the
interrupt line by writing DWC3_GEVNTSIZ_INTMASK to DWC3_GEVNTSIZ. If
there's a new event coming between reading the event count and interrupt
deassertion, dwc3 will lose previous pending events. More generally, we
will see 0 event count, which should not affect anything.
This shouldn't be possible in the current dwc3 implementation. However,
through testing and reading the PCIe trace, the TH occasionally still
gets invoked one more time after HW interrupt deassertion. (With PCIe
legacy interrupts, TH is called repeatedly as long as the interrupt line
is asserted). We suspect that there is a small detection delay in the
SW.
To avoid this issue, Check DWC3_EVENT_PENDING flag to determine if the
events are processed in the bottom-half IRQ handler. If not, return
IRQ_HANDLED and don't process new event.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 08a36b5438 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
caused a small change in the way ISO transfer is handled in the case
when XferInProgress event happens on Isoc EP with an active transfer.
This caused a performance degradation of 50%. e.g. using g_webcam on DUT
and luvcview on host the video frame rate dropped from 16fps to 8fps
@high-speed.
Make the ISO transfer handling equivalent to that prior to that commit
to get back the original ISO performance numbers.
Fixes: 08a36b5438 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Intel Cannonlake PCH has the same DWC3 than Intel
Sunrisepoint. Add the new IDs to the supported devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here is the big USB patchset for 4.12-rc1.
Lots of good stuff here, after many many many attempts, the kernel
finally has a working typeC interface, many thanks to the Heikki and
Guenter and others who have taken the time to get this merged. It
wasn't an easy path for them at all.
There's also a staging driver that uses this new api, which is why it's
coming in through this tree.
Along with that, there's the usual huge number of changes for gadget
drivers, xhci, and other stuff. Johan also finally refactored pretty
much every driver that was looking at USB endpoints to do it in a common
way, which will help prevent any "badly-formed" devices from causing
problems in drivers. That too wasn't a simple task.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvEIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yny4gCePCXxnrQdMWE+IMXf1H1hMubLkVkAn0ZWgQkq
BspgO7ZmGb+9Fpf6YvNz
=nwAu
-----END PGP SIGNATURE-----
Merge tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.12-rc1.
Lots of good stuff here, after many many many attempts, the kernel
finally has a working typeC interface, many thanks to Heikki and
Guenter and others who have taken the time to get this merged. It
wasn't an easy path for them at all.
There's also a staging driver that uses this new api, which is why
it's coming in through this tree.
Along with that, there's the usual huge number of changes for gadget
drivers, xhci, and other stuff. Johan also finally refactored pretty
much every driver that was looking at USB endpoints to do it in a
common way, which will help prevent any "badly-formed" devices from
causing problems in drivers. That too wasn't a simple task.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
staging: typec: Fairchild FUSB302 Type-c chip driver
staging: typec: Type-C Port Controller Interface driver (tcpci)
staging: typec: USB Type-C Port Manager (tcpm)
usb: host: xhci: remove #ifdef around PM functions
usb: musb: don't mark of_dev_auxdata as initdata
usb: misc: legousbtower: Fix buffers on stack
USB: Revert "cdc-wdm: fix "out-of-sync" due to missing notifications"
usb: Make sure usb/phy/of gets built-in
USB: storage: e-mail update in drivers/usb/storage/unusual_devs.h
usb: host: xhci: print correct command ring address
usb: host: xhci: delete sp_dma_buffers for scratchpad
usb: host: xhci: using correct specification chapter reference for DCBAAP
xhci: switch to pci_alloc_irq_vectors
usb: host: xhci-plat: set resume_quirk() for R-Car controllers
usb: host: xhci-plat: add resume_quirk()
usb: host: xhci-plat: enable clk in resume timing
usb: host: plat: Enable xHCI plat runtime PM
USB: serial: ftdi_sio: add device ID for Microsemi/Arrow SF2PLUS Dev Kit
USB: serial: constify static arrays
usb: fix some references for /proc/bus/usb
...
Core changes
- Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
This was a much discussed change. It affects use cases where people
write drivers that might or might not be using GPIO resources.
I have decided that this is the lesser evil right now.
- Make gpiod_count() behave consistently across different hardware
descriptions.
- Fix the syntax around open drain/open source to not infer active
high/low semantics.
New drivers
- A new single-register fixed-direction framework driver for hardware
that have lines controlled by a single register that just work in
one direction (out or in), including IRQ support.
- Support the Fintek F71889A GPIO SuperIO controller.
- Support the National NI 169445 MMIO GPIO.
- Support for the X-Gene derivative of the DWC GPIO controller
- Support for the Rohm BD9571MWV-M PMIC GPIO controller.
- Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
and replace both the Gemini and the Moxa ART custom drivers with
this driver.
Driver improvements
- A whole slew of drivers have their spinlocks chaned to raw spinlocks
as they provide irqchips, and thus we are progressing on realtime
compliance.
- Use devm_irq_alloc_descs() in a slew of drivers, getting managed
resources.
- Support for the embedded PWM controller inside the MVEBU driver.
- Debounce, open source and open drain support for the Aspeed driver.
- Misc smaller fixes like spelling and syntax and whatnot.
-----BEGIN PGP SIGNATURE-----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=DGPb
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.12 kernel cycle.
Core changes:
- Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
This was a much discussed change. It affects use cases where people
write drivers that might or might not be using GPIO resources. I
have decided that this is the lesser evil right now.
- Make gpiod_count() behave consistently across different hardware
descriptions.
- Fix the syntax around open drain/open source to not infer active
high/low semantics.
New drivers:
- A new single-register fixed-direction framework driver for hardware
that have lines controlled by a single register that just work in
one direction (out or in), including IRQ support.
- Support the Fintek F71889A GPIO SuperIO controller.
- Support the National NI 169445 MMIO GPIO.
- Support for the X-Gene derivative of the DWC GPIO controller
- Support for the Rohm BD9571MWV-M PMIC GPIO controller.
- Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
and replace both the Gemini and the Moxa ART custom drivers with
this driver.
Driver improvements:
- A whole slew of drivers have their spinlocks chaned to raw
spinlocks as they provide irqchips, and thus we are progressing on
realtime compliance.
- Use devm_irq_alloc_descs() in a slew of drivers, getting managed
resources.
- Support for the embedded PWM controller inside the MVEBU driver.
- Debounce, open source and open drain support for the Aspeed driver.
- Misc smaller fixes like spelling and syntax and whatnot"
* tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: f7188x: Add a missing break
gpio: omap: return error if requested debounce time is not possible
gpio: Add ROHM BD9571MWV-M PMIC GPIO driver
gpio: gpio-wcove: fix GPIO IRQ status mask
gpio: DT bindings, move tca9554 from pcf857x to pca953x
gpio: move tca9554 from pcf857x to pca953x
gpio: arizona: Correct check whether the pin is an input
gpio: Add XRA1403 DTS binding documentation
dt-bindings: add exar to vendor prefixes list
gpio: gpio-wcove: fix irq pending status bit width
gpio: dwapb: use dwapb_read instead of readl_relaxed
gpio: aspeed: Add open-source and open-drain support
gpio: aspeed: Add debounce support
gpio: aspeed: dt: Add optional clocks property
gpio: aspeed: dt: Fix description alignment in bindings document
gpio: mvebu: Add limited PWM support
gpio: Use unsigned int for interrupt numbers
gpio: f7188x: Add F71889A GPIO support.
gpio: core: Decouple open drain/source flag with active low/high
gpio: arizona: Correct handling for reading input GPIOs
...
With 51 non-merge commits, this is one of the smallest USB Gadget pull
requests. Apart from your expected set of non-critical fixes, and
other miscellaneous items, we have most of the changes in dwc3 (52.5%)
with all other UDCs following with 34.8%.
As for the actual changes, the most important of them are all the
recent changes to reduce memory footprint of dwc3, bare minimum
dual-role support on dwc3 and reworked endpoint count and
initialization routines.
-----BEGIN PGP SIGNATURE-----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=wYOI
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.12
With 51 non-merge commits, this is one of the smallest USB Gadget pull
requests. Apart from your expected set of non-critical fixes, and
other miscellaneous items, we have most of the changes in dwc3 (52.5%)
with all other UDCs following with 34.8%.
As for the actual changes, the most important of them are all the
recent changes to reduce memory footprint of dwc3, bare minimum
dual-role support on dwc3 and reworked endpoint count and
initialization routines.
If dr_mode is "otg" then support dual role mode of operation.
Currently this mode is only supported when an extcon handle is
present in the dwc3 device tree node. This is needed to
get the ID status events of the port.
We're using a workqueue to manage the dual-role state transitions
as the extcon notifier (dwc3_drd_notifier) is called in an atomic
context by extcon_sync() and this doesn't go well with
usb_del_gadget_udc() causing a lockdep and softirq warning.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We can't have both Host and Peripheral roles active at the same time
because of one detail on DWC3: it shares the same memory area for both
Host and Peripheral registers.
When swapping roles we must reinitialize the new role every
time. Let's make sure this works for our debugfs interface.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Each role is mutually exclusive, the | operator is unnecessary. Remove
it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We're going to use this member to track which role we're currently
playing, that way we can more easily implement dual-role swap in
upcoming patches.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's much simpler to just add one extra TRB chained to previous TRB to
handle ZLP. This helps us reduce pointless allocations and simplifies
the code a little bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just like we did for all other endpoint types, let's rely on a chained
TRB pointing to ep0_bounce_addr in order to align transfer size. This
will make the code simpler.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of constantly recomputing how dwc and epnum relate to dep,
just pass dep as argument.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we pass TRB's own address on bpl/bph fields, we can get our SETUP
packet as immediate data on the TRB itself, without having to allocate
extra memory for it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In order to improve usability a tiny bit, we will return strings that
match what our tracepoints return.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When writing, we expect the "otg" string. When showing, we return
"OTG". Let's downcase that word to avoid confusion.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To avoid checkpatch warnings with new patches let's
start using the BIT() macro wherever possible.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The gadget wants to set the starting microframe for the first ISOC TRB
to 4 microframes in the future, but it does so by multiplying the
dep->interval. This only works if dep->interval = 1. For other intervals
it will put it 4 *intervals* in the future which may be way too much.
Fix so that it always adds just one interval or at least 4 microframes.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Change goto labels to meaningful names from a series of errNs.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A previous patch in the series reduces the number of callsites of
dwc3_gadget_init_hw_endpoints from two to one. This patch removes the
redundant step of wrappering one function in the other, which can be done
by adding a parameter to dwc3_gadget_init_endpoints and moving the
linked-list initialization of dwc->gadet.ep_list.
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
- DWC_USB3_NUM indicates the number of Device mode single directional
endpoints, including OUT and IN endpoint 0.
- DWC_USB3_NUM_IN_EPS indicates the maximum number of Device mode IN
endpoints active at any time, including control endpoint 0.
It's possible to configure RTL such that DWC_USB3_NUM_EPS is equal to
DWC_USB3_NUM_IN_EPS.
dwc3-core calculates the number of OUT endpoints as DWC_USB3_NUM minus
DWC_USB3_NUM_IN_EPS. If RTL has been configured with DWC_USB3_NUM_IN_EPS
equal to DWC_USB3_NUM then dwc3-core will calculate the number of OUT
endpoints as zero.
For example a from dwc3_core_num_eps() shows:
[ 1.565000] /usb0@f01d0000: found 8 IN and 0 OUT endpoints
This patch refactors the endpoint calculation down to one variable
dwc->num_eps taking care to maintain the current mapping of endpoints for
fixed FPGA configurations as described in Table 4-7 of version 2.60a of the
DWC USB3 databook.
The endpoint mapping will then be EP-OUT, EP-IN etc, up to DWC_USB3_NUM.
If DWC_USB3_NUM is odd then OUT will take the extra endpoint.
Suggested-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We must make sure that our macros are safe against expressions passed
as arguments. We have seen one problem where GTXFIFOSIZ(n) was failing
when passed the expression (epnum >> 1) as argument. The problem was
caused by operator precedence between >> and *.
To make sure macros are safe, we just wrap argument with () when using
it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_log_msg trace class isn't used any more. Suggest to remove it.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This bit is only supposed to be used with known
buggy PHYs, however some platforms might erroneously
set it. In order to avoid it, let's make sure this
bit is always cleared. If some PHY needs this, we
will need to add a quirk flag.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This resolves a merge issue in the gadget code, and we want the USB
fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to use managed variant of acpi_dev_add_driver_gpios() to simplify
error path and fix potentially wrong assignment if ->probe() fails.
While here, add a debug message in case assignment fails to allow user
see the cause of a potential issue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the case of bounced ep0 requests, we must delay DMA operation until
after ->complete() otherwise we might overwrite contents of req->buf.
This caused problems with RNDIS gadget.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
a lot of embeded system SOC (e.g. freescale T2080) have both
PCI and USB modules. But USB module is controlled by registers directly,
it have no relationship with PCI module.
when say N here it will not build PCI related code in USB driver.
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes, we might get a completion for a TRB which is left with HWO
bit. Even in these cases, we should increment req->remaining to
properly report total transferred size. I noticed this while debuggin
a separate problem seen with MSC tests from USBCV. Sometimes we would
erroneously report a completion for a 512-byte transfer when, in
reality, we transferred 0 bytes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We need to break from all cases if we want to treat
each one of them separately.
Reported-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Fixes: d2728fb3e0 ("usb: dwc3: omap: Pass VBUS and ID events transparently")
Cc: <stable@vger.kernel.org> #v4.8+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On TI platforms (dra7, am437x), the DWC3_DSTS_DEVCTRLHLT bit is not set
after the device controller is stopped via DWC3_DCTL_RUN_STOP.
If we don't disconnect and stop the gadget, it stops working after a
system resume with the trace below.
There is no point in preventing gadget disconnect and gadget stop during
system suspend/resume as we're going to suspend in any case, whether
DEVCTRLHLT timed out or not.
[ 141.727480] ------------[ cut here ]------------
[ 141.732349] WARNING: CPU: 1 PID: 2135 at drivers/usb/dwc3/gadget.c:2384 dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3]
[ 141.744299] Modules linked in: usb_f_ss_lb g_zero libcomposite xhci_plat_hcd xhci_hcd usbcore dwc3 evdev udc_core m25p80 usb_common spi_nor snd_soc_davinci_mcasp snd_soc_simple_card snd_soc_edma snd_soc_tlv3e
[ 141.792163] CPU: 1 PID: 2135 Comm: irq/456-dwc3 Not tainted 4.10.0-rc8 #1138
[ 141.799547] Hardware name: Generic DRA74X (Flattened Device Tree)
[ 141.805940] [<c01101b4>] (unwind_backtrace) from [<c010c31c>] (show_stack+0x10/0x14)
[ 141.814066] [<c010c31c>] (show_stack) from [<c04a0918>] (dump_stack+0xac/0xe0)
[ 141.821648] [<c04a0918>] (dump_stack) from [<c013708c>] (__warn+0xd8/0x104)
[ 141.828955] [<c013708c>] (__warn) from [<c0137164>] (warn_slowpath_null+0x20/0x28)
[ 141.836902] [<c0137164>] (warn_slowpath_null) from [<bf27784c>] (dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3])
[ 141.848329] [<bf27784c>] (dwc3_stop_active_transfer.constprop.4 [dwc3]) from [<bf27ab14>] (__dwc3_gadget_ep_disable+0x64/0x528 [dwc3])
[ 141.861034] [<bf27ab14>] (__dwc3_gadget_ep_disable [dwc3]) from [<bf27c27c>] (dwc3_gadget_ep_disable+0x3c/0xc8 [dwc3])
[ 141.872280] [<bf27c27c>] (dwc3_gadget_ep_disable [dwc3]) from [<bf23b428>] (usb_ep_disable+0x11c/0x18c [udc_core])
[ 141.883160] [<bf23b428>] (usb_ep_disable [udc_core]) from [<bf342774>] (disable_ep+0x18/0x54 [usb_f_ss_lb])
[ 141.893408] [<bf342774>] (disable_ep [usb_f_ss_lb]) from [<bf3437b0>] (disable_endpoints+0x18/0x50 [usb_f_ss_lb])
[ 141.904168] [<bf3437b0>] (disable_endpoints [usb_f_ss_lb]) from [<bf343814>] (disable_source_sink+0x2c/0x34 [usb_f_ss_lb])
[ 141.915771] [<bf343814>] (disable_source_sink [usb_f_ss_lb]) from [<bf329a9c>] (reset_config+0x48/0x7c [libcomposite])
[ 141.927012] [<bf329a9c>] (reset_config [libcomposite]) from [<bf329afc>] (composite_disconnect+0x2c/0x54 [libcomposite])
[ 141.938444] [<bf329afc>] (composite_disconnect [libcomposite]) from [<bf23d7dc>] (usb_gadget_udc_reset+0x10/0x34 [udc_core])
[ 141.950237] [<bf23d7dc>] (usb_gadget_udc_reset [udc_core]) from [<bf276d70>] (dwc3_gadget_reset_interrupt+0x64/0x698 [dwc3])
[ 141.962022] [<bf276d70>] (dwc3_gadget_reset_interrupt [dwc3]) from [<bf27952c>] (dwc3_thread_interrupt+0x618/0x1a3c [dwc3])
[ 141.973723] [<bf27952c>] (dwc3_thread_interrupt [dwc3]) from [<c01a7ce8>] (irq_thread_fn+0x1c/0x54)
[ 141.983215] [<c01a7ce8>] (irq_thread_fn) from [<c01a7fbc>] (irq_thread+0x120/0x1f0)
[ 141.991247] [<c01a7fbc>] (irq_thread) from [<c015ba14>] (kthread+0xf8/0x138)
[ 141.998641] [<c015ba14>] (kthread) from [<c01078f0>] (ret_from_fork+0x14/0x24)
[ 142.006213] ---[ end trace b4ecfe9f175b9a9c ]---
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The utmi mode is unsigned according the dt-bindings.
Fix sparse issue (-Wtypesign):
drivers/usb/dwc3/dwc3-omap.c:391:50: warning: incorrect type in argument 3 (different signedness)
drivers/usb/dwc3/dwc3-omap.c:391:50: expected unsigned int [usertype] *out_value
drivers/usb/dwc3/dwc3-omap.c:391:50: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If request was already started, this means we had to
stop the transfer. With that we also need to ignore
all TRBs used by the request, however TRBs can only
be modified after completion of END_TRANSFER
command. So what we have to do here is wait for
END_TRANSFER completion and only after that jump
over TRBs by clearing HWO and incrementing dequeue
pointer.
Note that we have 2 possible types of transfers
here:
i) Linear buffer request
ii) SG-list based request
SG-list based requests will have r->num_pending_sgs
set to a valid number (> 0). Linear requests,
normally use a single TRB.
For each of these two cases, if r->unaligned flag is
set, one extra TRB has been used to align transfer
size to wMaxPacketSize.
All of these cases need to be taken into
consideration so we don't mess up our TRB ring
pointers.
Tested-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some gadget drivers are bad, bad boys. We notice
that ADB was passing bad Burst Size which caused top
bits of param0 to be overwritten which confused DWC3
when running this command.
In order to avoid future issues, we're going to make
sure values passed by macros are always safe for the
controller. Note that ADB still needs a fix to *not*
pass bad values.
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Mohamed Abbas <mohamed.abbas@intel.com>
Sugested-by: Adam Andruszak <adam.andruszak@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
-----BEGIN PGP SIGNATURE-----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=gk8j
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v4.11
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
dwc3 revisions <=3.00a have a limitation where Port Disable command
doesn't work. Set the quirk-broken-port-ped property for such
controllers so XHCI core can do the necessary workaround.
[rogerq@ti.com] Updated code from platform data to device property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of assuming all IN endpoints support 1024
bytes, let's read the actual value from HW and pass
that to gadget API.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
At least macOS seems to be sending
ClearFeature(ENDPOINT_HALT) to endpoints which
aren't Halted. This makes DWC3's CLEARSTALL command
time out which causes several issues for the driver.
Instead, let's just return 0 and bail out early.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When handing the SETUP packet by composite_setup(), we will release the
dwc->lock. If we get the 'USB_GADGET_DELAYED_STATUS' result from setup
function, which means we need to delay handling the STATUS phase.
But during the lock release period, maybe the request for handling delay
STATUS phase has been queued into list before we set 'dwc->delayed_status'
flag or entering 'EP0_STATUS_PHASE' phase, then we will miss the chance
to handle the STATUS phase. Thus we should check if the request for delay
STATUS phase has been enqueued when entering 'EP0_STATUS_PHASE' phase in
dwc3_ep0_xfernotready(), if so, we should handle it.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch uses the resource-managed extcon API for extcon_register_notifier()
and replaces the deprecated extcon API as following:
- extcon_get_cable_state_() -> extcon_get_state()
Cc: linux-omap@vger.kernel.org
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of passing quirk_ep_out_aligned_size, we can use one extra TRB
to align transfer to wMaxPacketSize.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allocate a coherent buffer of 1024 bytes (size of a single superspeed
bulk packet) to serve as bounce buffer for an extra TRB needed to align
transfers to wMaxPacketSize.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This new internal function will be used to solve a minor issue with dwc3
which exists in regards to short packets with OUT endpoints. Currently
we're asking gadget driver to *always* send us aligned requests; however
if we have enough TRBs we can easily append one extra TRB chained to the
previous and keep a throw away 1024 byte buffer around for that.
The actual fix will come in a separate patch, this is merely in
preparation for such fix.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We are already passing struct dwc3_request * to dwc3_prepare_one_trb(),
because of that there's no need to extract dma address and length in the
caller. We can let dwc3_prepare_one_trb() itself handle that part.
This simplifies the prototype of the function by removing two arguments.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Exynos is DT-only, so there's no need for a platform MODALIAS.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3-exynos prints debug message when suspend clock is not specified.
The suspend clock is optional and driver can work without it.
This debug message doesn't add any value and leads to confusion and
concern. Remove it.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Axius clock error path returns without disabling clock and suspend clock.
Fix it to disable them before returning error.
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DCFG.DEVSPD == 0x3 is not valid and we need to set
DCFG.DEVSPD to 0x1 for full speed mode. Same goes for
DSTS.CONNECTSPD.
Old databooks had 0x3 for full speed in 48MHz mode for
USB1.1 transceivers which was never supported. Newer databooks
don't mention 0x3 at all.
Cc: John Youn <John.Youn@synopsys.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Intel Gemini Lake SoC has the same DWC3 than Broxton. Add
the new ID to the supported Devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Calling platform_device_add_properties() replaces existing properties so
the "linux,sysdev_is_parent" property doesn't get set. Add this property
to each platform.
Fixes: d64ff406e5 ("usb: dwc3: use bus->sysdev for DMA configuration")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now races can happen between interrupt handler execution and PM runtime in
error handling code path in probe and in dwc3_omap_remove() which will lead
to system crash:
in probe:
...
err1:
pm_runtime_put_sync(dev);
^^ PM runtime can race with IRQ handler when deferred probing happening
due to extcon
pm_runtime_disable(dev);
return ret;
in dwc3_omap_remove:
...
dwc3_omap_disable_irqs(omap);
^^ IRQs are disabled in HW, but handler may still run
of_platform_depopulate(omap->dev);
pm_runtime_put_sync(&pdev->dev);
^^ PM runtime can race with IRQ handler
pm_runtime_disable(&pdev->dev);
return 0;
So, OMAP DWC3 IRQ need to be disabled before calling
pm_runtime_put() in probe and in dwc3_omap_remove().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case EP disabled pass only EPCPLT command
to be handled. In other case we could hit
Bug like below.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000003
IP:
[<ffffffff81673428>] dwc3_thread_interrupt+0x11c8/0x1790
while dep->endpoint.desc is NULL.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb_get_dr_mode() expects the device-property to be spelled
"dr_mode" not "dr-mode".
Spelling it properly fixes the following warning showing up in dmesg:
[ 8704.500545] dwc3 dwc3.2.auto: Configuration mismatch. dr_mode forced to gadget
Signed-off-by: Hans de Goede <hdegoede@redhat.com
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we're handling so many transfers at a time
and for some dwc3 revisions LPM events *must* be
enabled, we can fall into a situation where too many
events fire and we start receiving Overflow events.
Let's do what XHCI does and allocate a full page for
the Event Ring, this will avoid any future issues.
Cc: <stable@vger.kernel.org> # v4.9
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit 0416e494ce ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced") introduced a bug
where we would leak DMA resources which would cause
us to starve the system of them resulting in failing
DMA transfers.
Fix the bug by making sure that we always unmap EP0
requests since those are *always* mapped.
Fixes: 0416e494ce ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced")
Cc: <stable@vger.kernel.org>
Tested-by: Tomasz Medrek <tomaszx.medrek@intel.com>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Let's call dwc3_ep0_prepare_one_trb() explicitly
because there are occasions where we will need more
than one TRB to handle an EP0 transfer.
A follow-up patch will fix one bug related to
multiple-TRB Data Phases when it comes to
mapping/unmapping requests for DMA.
Cc: <stable@vger.kernel.org>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For now this is just a cleanup patch, no functional
changes. We will be using the new function to fix a
bug introduced long ago by commit 0416e494ce
("usb: dwc3: ep0: correct cache sync issue in case
of ep0_bounced") and further worsened by commit
c0bd5456a4 ("usb: dwc3: ep0: handle non maxpacket
aligned transfers > 512")
Cc: <stable@vger.kernel.org>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----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=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
The dma mask is correctly set up by the DT probe function, no
need to override it any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dma ops for dwc3 devices are not set properly. So, use a
physical device sysdev, which will be inherited from parent,
to set the hardware / firmware parameters like dma.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Building with W=1, we get a warning about harmless empty statements:
drivers/usb/dwc3/ep0.c: In function 'dwc3_ep0_handle_intf':
drivers/usb/dwc3/ep0.c:491:4: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
Instead of adding empty braces which would introduce checkpatch.pl
warnings, we're just removing the code which doesn't do anything and
making sure we return 0 so USBCV tool is happy.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_pci_dsm() is only needed if (PM || PM_SLEEP),
we should make sure it's not defined if neither of
those is defined.
This fixes a randconfig build warning.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is a workaround for STAR 9000961433 which affects only version
3.00a of the DWC_usb3 core. This prevents the controller interrupt from
being masked while handling events. Enabling interrupt moderation allows
us to work around this issue because once the GEVNTCOUNT.count is
written the IRQ is immediately deasserted and won't be asserted again
until GEVNTCOUNT.EHB is cleared.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implement interrupt moderation which allows the interrupt rate to be
throttled. To enable this feature the dwc->imod_interval must be set to
1 or greater. This value specifies the minimum inter-interrupt interval,
in 250 ns increments. A value of 0 disables interrupt moderation.
This applies for DWC_usb3 version 3.00a and higher and for DWC_usb31
version 1.20a and higher.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that all the infrastructure is in place, we can
clear events in the top-half handler in order to
bring IRQ line low ASAP.
This is also a necessary step in order to implement
workaround for known erratum in follow-up patches.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Let's start copying events from evt->buf to
evt->cache and use evt->cache for processing events.
A follow-up patch will be added to clear events in
the top-half handler in order to bring IRQ line low
as soon as possible.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of always accessing the macro directly,
let's rely on evt->length which is the actual length
of current event buffer. While unlikely, we could
change event buffer's size at any time.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This extra buffer will be used so we can copy
triggered events from our event buffer to this cache
and process all of them later in bottom half
handler.
We need this in order to implement a workaround for
a known erratum in recent DWC3 release.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_soft_reset() is doing the same thing as
dwc3_core_soft_reset(). Let's remove
dwc3_soft_reset() since that's not needed anymore.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a function to check properties and call it from probe. This will
allow us to add check code without bloating the probe function. This
needs to be done after dwc3_get_properties() and dwc3_core_init() so
that all the properties and hardware configs are available.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a helper function to check if we are running on a DWC_usb3 core.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The register programming code in dwc2_updated_ram_clk_sel() will never
be executed. And in fact the entire function can be removed as there is
no way to override the default value of GCTL.RAMCLKSEL. Remove the
function and add a comment explaining where GCTL.RAMCLKSEL should be
programmed if needed in the future.
This fixes dead code warnings in coverity.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The __dwc3_gadget_endpoint_enable() function has access to the endpoint
descriptors via the usb_ep. So we don't need to pass them in as
arguments. The descriptors should be set by the caller prior to calling
usb_ep_enable().
Signed-off-by: John Youn <johnyoun@synopsys.com>
[felipe.balbi@linux.intel.com : minor improvements]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Seems last time we hit few issues where
we get trb_left = 0, mainly because of
HWO bit still set in previous TRB.
Add warn on once to catch/fix such
problems much faster.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After we kick_transfer we should clean
DWC3_EP_PENDING_REQUEST endpoint flag.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use pre-increment and set -ETIMEDOUT correctly.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case STARTTRANSFER will fail, clean TRB.
Seems HW in such case don't clean HWO bit.
So, without this cleanup prev_trb still have
HWO bit set.
In my case (without patch), after first START failed:
- dep->enqueue == 1
- dep->dequeue == 1
- prev_trb still have HWO set
- left_trb() == 0
No way to send more data.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we will fail to STARTTRANSFER we should
also decrement queued_requests.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Finally get rid of dwc3_trace() hack. If any other
message is truly needed, we should add proper
tracepoints for them instead of hacking around with
dwc3_trace() or similar.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of using a simple trace_printk() wrapper,
let's add an actual tracepoint and print further
details about the endpoint being operated upon.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Intel's BXT devices need to execute a _DSM method
during {runtime_,}{suspend,resume} in order to get a
chunk of dwc3 to power gate and save some extra
power.
Let's do that now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We'll be tracking a little more information for PCI
drivers, it's about time we add a private structure
for that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we get a half-way processed request, we should
make sure to try to prepare further TRBs for it or
for any possibly queued up request held in our
pending_list. This will make sure our controller is
kept busy for as long as possible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Say we have three requests prepared to the HW (reqA,
reqB, and reqC). All of them are composed of
SG-lists with several entries and they all requests
interrupt only on last TRBs of the SG-list.
When we get interrupt for reqA, it could be that
reqB is already half-way transferred and some of its
TRBs will have HWO already cleared.
It's okay to free up TRBs without HWO bit set, but
we need to guarantee we don't giveback a request
that's half-way transferred as that will confuse
gadget drivers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In cases where we're given an SG-list which is
longer than the amount of currently available TRBs,
we will be left with the same request on
started_list and we should prioritize that request
over possible new requests on pending_list. That's
a way to guarantee requests complete in order.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will give us a simpler way of figuring out how
many bytes were left in each TRB. It's useful for
cases where we queue only part of an SG-list due to
amount of available TRBs at the time of kicking the
transfer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If XferNotReady comes before usb_ep_queue() we will
set our PENDING request flag and wait for a
request. However, originally, we were assuming
usb_ep_queue() would always happen before our first
XferNotReady and that causes a corner case where we
could try to issue ENDTRANSFER command before
STARTTRANSFER.
Let's fix that by tracking endpoints which have been
started.
Reported-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of just delaying for 100us, we should
actually wait for End Transfer Command Complete
interrupt before moving on. Note that this should
only be done if we're dealing with one of the core
revisions that actually require the interrupt before
moving on.
[ felipe.balbi@linux.intel.com: minor improvements ]
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The combo of list_empty() check and return list_first_entry()
can be replaced with list_first_entry_or_null().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we change the USB function with configfs dynamically, we possibly
met this situation: one core is doing the control transfer, another core
is trying to unregister the USB gadget from userspace, we must wait for
completing this control tranfer, or it will hang the controller to set
the DEVCTRLHLT flag.
[ felipe.balbi@linux.intel.com: several fixes to the patch
- call complete() before starting following SETUP transfer
- add a macro for ep0_in_setup's timeout
- change commit subject slightly
- break lines at 72 characters (git adds an 8-character tab)
- avoid changes to dwc3_gadget_run_stop() ]
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
That function is unnecessarily called from
dwc3_gadget_reset_interrupt(). Gadget drivers (and
thus, functions) are required to dequeue all pending
requests when they get notified about a USB Bus
Reset.
Trying to make sure there are no pending requests
only serves the purpose of working around possibly
bad gadgets.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This helper will be responsible for reading and
parsing our properties. No functional changes in
this patch, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This little helper will be used to setup anything
related to GCTL register. There are no functional
changes, this is a cleanup only patch.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This little helper will be used to make sure we're
dealing with a valid Synopsys DWC3 or DWC3.1 core.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For the usb31 IP and from version 2.90a of the usb3 IP, the core
supports HW exit from L1 in HS. Enable it, otherwise the controller may
never exit from LPM to do a transfer.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Member @mem in struct dwc3 is not used in any places. Clean up it.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should never kill the machine just because some
USB endpoint type is wrong. WARN about it and move
on.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't need to know about short packets unless
gadget driver told us it's not ok to see them on the
bus. In the normal situation we can continue
processing the list of requests if we get a Short
packet.
Also, note that we're making sure ISP is only set
for OUT endpoints, where that setting is valid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
CSP bit is only valid for OUT endpoints. Synopsys
databook is unclear if HW ignores CSP for IN
endpoints (chances are, it does) but to avoid
problems, let's make sure to set CSP only when valid
to do so.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By extracting smaller functions from
dwc3_ep0_handle_feature(), it becomes far easier to
understand what's going on. Cleanup only, no
functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We want to reduce the usage of dwc3_trace() in favor
of proper tracepoints which can be enabled/disabled
by the user. Let's start with our register
accessors.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We shouldn't have any glue layer which doesn't
compile everywhere. In order to make sure this is
always the case, make sure COMPILE_TEST is properly
added at dependency list of a config entry.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't need dwc3_trace() unless we're building a
kernel with CONFIG_FTRACE. This patch reduces
dwc3.ko text size a bit while also removing overhead
of dwc3_trace() calls.
text data bss dec hex filename
50796 581 0 51377 c8b1 drivers/usb/dwc3/dwc3.o
43961 581 0 44542 adfe drivers/usb/dwc3/dwc3.o.patched
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We can offset the latency of a full Start Transfer
command - where we _must_ poll for its completion -
to usb_ep_enable() time. This means that once
requests start showing up from the gadget driver, we
can rely on No Response Update Transfer command -
where we don't need to poll for completion.
This patch, starts implementing this method for Bulk
endpoints, even though, technically, we could extend
it to all other endpoints in future commits.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of periodic transfers, let's pretty print
the size field as a multiplier followed by length,
such as :
3x 1024
instead of:
33555456
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With this extra piece of information, it will be
easier to find mismatches between driver and HW.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will be using dwc3_ep0_state_string() from within
our tracepoints, so we need to move that helper to
debug.h in order for it to be accessible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Removing some trace prints which were made redundant
when we started decoding events and TRBs completely
within their respective trace points.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 can tell us which phase of a setup transfer
we're getting into. Let's decode it from the event
to make it easier to debug.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link State Change events are only needed for
debugging and to apply certain workarounds on known
errata. Let's save a few cycles by disabling these
events completely on working revisions of the core.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There might be situations where a Start Transfer
command might fail, if that ever happens, instead of
simply removing the request from our list, we should
give the request back to the gadget driver,
otherwise we might eventually starve it from requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No Response Update Transfer is a special type of
Update Transfer command which can be used whenever
we're not relying on XferNotReady to prepare
transfers. With this, we don't need to wait for
CMDACT to be cleared and issue further commands to
the endpoint straight away.
Let's start using this version to skip the long-ish
wait.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The cmd argument we pass to
dwc3_send_gadget_ep_cmd() could contain extra
arguments embedded. When checking for StartTransfer
command, we need to make sure to match only lower 4
bits which contain the actual command and ignore the
rest.
Reported-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of High-Speed, High-Bandwidth endpoints, we
need to tell DWC3 that we have more than one packet
per interval. We do that by setting PCM1 field of
Isochronous-First TRB.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3-st uses pinctrl_pm_select_*_state() however it
doesn't include the necessary header. Fix the build
break caused by that, by simply including the
missing header.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In commit 2abd9d5fa6 ("usb: dwc3: ep0: Add chained TRB support"), the
size of the memory allocated with 'dma_alloc_coherent()' has been modified
but the corresponding calls to 'dma_free_coherent()' have not been updated
accordingly.
This has been spotted with coccinelle, using the following script:
////////////////////
@r@
expression x0, x1, y0, y1, z0, z1, t0, t1, ret;
@@
* ret = dma_alloc_coherent(x0, y0, z0, t0);
...
* dma_free_coherent(x1, y1, ret, t1);
@script:python@
y0 << r.y0;
y1 << r.y1;
@@
if y1.find(y0) == -1:
print "WARNING: sizes look different: '%s' vs '%s'" % (y0, y1)
////////////////////
Fixes: 2abd9d5fa6 ("usb: dwc3: ep0: Add chained TRB support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We cannot pre-start isochronous endpoints because we
rely on the micro-frame number passed via
XferNotReady command for proper Isochronous
scheduling.
Fixes: 08a36b5438 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some requests could be accounted for multiple
times. Let's fix that so each and every requests is
accounted for only once.
Cc: <stable@vger.kernel.org> # v4.8
Fixes: 55a0237f8f ("usb: dwc3: gadget: use allocated/queued reqs for LST bit")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
-----BEGIN PGP SIGNATURE-----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=vTFa
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.9 merge window
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
Add necessary compatible flag for Cavium's DWC3 so
dwc3-of-simple will probe.
Tested-by: Steven J. Hill <Steven.Hill@cavium.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of erroring out when we don't have clocks,
let's just avoid any calls to the clk API.
Tested-by: Steven J. Hill <Steven.Hill@cavium.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc3_of_simple_remove() we are using clk_unprepare() before doing
any clk_disable(). If we enable Common CLK framework (CCF) and try to
unbind dwc3-of-simple driver, we see kernel WARN messages.
This patch fixes this kernel warning by using clk_disable_unprepare()
instead of clk_unprepare().
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 50c763f8c1 ("usb: dwc3: Set the ClearPendIN bit on Clear
Stall EP command") sets ClearPendIN bit for all IN endpoints of
v2.60a+ cores. This causes ClearStall command fails on 2.60+ cores
operating in HighSpeed mode.
In page 539 of 2.60a specification:
"When issuing Clear Stall command for IN endpoints in SuperSpeed
mode, the software must set the "ClearPendIN" bit to '1' to
clear any pending IN transcations, so that the device does not
expect any ACK TP from the host for the data sent earlier."
It's obvious that we only need to apply this rule to those IN
endpoints that currently operating in SuperSpeed mode.
Fixes: 50c763f8c1 ("usb: dwc3: Set the ClearPendIN bit on Clear Stall EP command")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cleaning up the loop in dwc3_cleanup_done_reqs() introduced a
gcc warning if built with "-Wmaybe-uninitialized":
drivers/usb/dwc3/gadget.c: In function 'dwc3_endpoint_transfer_complete':
drivers/usb/dwc3/gadget.c:2015:9: 'trb' may be used uninitialized in this function [-Wmaybe-uninitialized]
I believe it is a false positive and we always have a valid 'trb'
pointer at the end of the function, but neither I nor the compiler
are able to prove that.
This works around the warning by computing a flag earlier in the function
when it's guaranteed to be valid, which tells the compiler that it's
safe and makes it easier to understand to me.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 31162af447 ("usb: dwc3: gadget: avoid while (1) loop on completion")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When building a kernel with CONFIG_PM_SLEEP=n, we
get the following warning:
drivers/usb/dwc3/dwc3-pci.c:253:12: warning: 'dwc3_pci_pm_dummy' defined but not used
In order to fix this, we should only define
dwc3_pci_pm_dummy() when CONFIG_PM_SLEEP is defined.
Fixes: f6c274e11e ("usb: dwc3: pci: runtime_resume child device")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch follows the similar fix in dwc2. See
commit 5268ed9d2e ("usb: dwc2: Fix dr_mode validation")
Currently, the dr_mode is only checked against the module configuration.
It also needs to be checked against the hardware capablities.
The driver now checks if both the module configuration and hardware are
capable of the dr_mode value. If not, then it will issue a warning and
fall back to a supported value. If it is unable to fall back to a
suitable value, then the probe will fail.
Behavior summary:
module : actual
HW config dr_mode : dr_mode
---------------------------------
host host any : host
host dev any : INVALID
host otg any : host
dev host any : INVALID
dev dev any : dev
dev otg any : dev
otg host any : host
otg dev any : dev
otg otg any : dr_mode
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ulpi_register_interface() accepts a const struct ulpi_ops and dwc3
doesn't perform any changes to this struct at runtime, so there's no
reason it shouldn't be constant.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With the removal of the old {read|write} operations, we can now safely
rename the new api operations {read|write}_dev to use the shorter and
clearer names {read|write}, respectively.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The old read, write callbacks in struct ulpi_ops have been deprecated
in favor of new callbacks that pass the parent device directly.
Replace the used callbacks in dwc3's ulpi component with the new api.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit 6f8245b4e3 ("usb: dwc3: gadget: always decrement
by 1").
We can't always decrement this value.
We should decrement only if the calculation of free slots results in a
LINK TRB being among one of the free slots (dequeue < enqueue).
Otherwise, if the LINK TRB is not among the free slots then it should
not be decremented.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case our TRB ring is full, we can avoid trying to
kick transfers which won't start and just add requests
to the queue.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ENDXFER polling is available on version 3.10a and later of the
DWC_usb3 (USB 3.0) controller. With this feature, the software can poll
the CMDACT bit in the DEPCMD register after issuing an ENDXFER command.
This feature is enabled by writing GUCTL2[14].
This feature is NOT available on the DWC_usb31 (USB 3.1) IP.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add revision number constants for the 3.00a and 3.10a releases.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When dwc3 core enters into suspend mode, the system (especially for mobile
device) may power off the dwc3 controller for power saving, that will cause
dwc3 controller lost the mode operation when resuming dwc3 core.
Thus we can move the mode setting into dwc3_core_init() function to avoid this
issue.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rockchip platform merely enable usb3 clocks and
populate its children. So we can use this generic
glue layer to support Rockchip dwc3.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support to configure the UTMI+ PHY with an 8- or 16-bit
interface via DT. The UTMI+ PHY interface is a hardware
capability, and it's platform dependent. Normally, the
PHYIF can be configured during coreconsultant.
But for some specific USB cores(e.g. rk3399 SoC DWC3),
the default PHYIF configuration value is false, so we
need to reconfigure it by software.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Upon transfer completion after a full ring, let's
add more TRBs to our ring in order to complete our
request successfully.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There was a typo when generating endpoint name which
would be very confusing when debugging. Fix it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the ring is full and we are processing a big
sglist, then let's interrupt so we can, later, add
more TRBs to the ring.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These two fields will be used in a follow-up patch
to track how many entries of request's sglist we
have already processed. The reason is that if a
gadget driver sends an sglist with more entries then
we can fit in the ring, we will have to continue
processing remaining afterwards.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We know that we have to iterate over the list of
started requests. Instead of looping forever, we can
rely on list_for_each_entry(). Likewise, instead of
a do {} while loop over all, maybe available,
scatterlist entries, we can detect if $this request
uses scatterlist and rely on for_each_sg().
This makes the code easier to follow while making
sure that we will *always* break out of the loop.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Many of the comments in that function are really
outdated and don't match what the driver is
doing. Moreover, recent patches combined programming
model for all non-control endpoints, this gives us
an opportunity to get rid of our special cases in
__dwc3_gadget_ep_queue().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We always need to decrement our index by at least
one. Simplify the implementation by using a
temporary local variable and making sure that we
will always decrement one extra if tmp == 0.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of waiting until giveback before
incrementing the dequeue pointer, we can increment
it from dwc3_cleanup_done_reqs(), that way we avoid
an extra loop over all TRBs during giveback.
While at that, also avoid using req->first_trb_index
as that's completely unnecessary. A follow-up patch
will clean up further uses of that and remove the
field altogether.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The only endpoint which actually requires LST bit
and XferComplete is ep0/1. Let's save some time by
completely removing LST bit support and
XferComplete.
This simplifies and consolidates endpoint handling
for all other 3 transfer types while also avoiding
extra interrupts.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
__dwc3_gadget_wakeup() is called while holding a spinlock, then depends on
jiffies in order to timeout while polling the USB core for a link state
update. In the case the wakeup failed, the timeout will never happen and
will also cause the cpu to stall until rcu_preempt kicks in.
This switches to a "decrement variable and wait" timeout scheme.
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After going through runtime_suspend/runtime_resume
cycle once we would be left with an unbalanced
pm_runtime_get() call. Fix that by making sure that
we try to suspend right after resuming so things are
balanced and device can runtime_suspend again.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
During runtime_resume of dwc3-pci.c, we need to
runtime suspend our child device (which is dwc3
proper) otherwise nothing will happen.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
stop consuming TRBs when we reach one with HWO bit
already set. This will prevent us from prematurely
retiring a TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Synopsys Databook 2.60a, section 8.3.4,
it's stated that:
The LST bit should be set to 0 (isochronous
transfers normally continue until the
endpoint is removed entirely, at which time
an End Transfer command is used to stop the
transfer).
This patch makes sure that detail is observed and
fixes a regression with Android Audio playback
caused by recent changes to DWC3 gadget.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add missing platform_set_drvdata() in dwc3_of_simple_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Intel Kabylake PCH has the same DWC3 than Intel
Sunrisepoint. Add the new ID to the supported devices.
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we stop earlier due to short packet, we will
not be able to giveback all TRBs.
Cc: <stable@vger.kernel.org>
Cc: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 has one interesting peculiarity with chained
transfers. If we setup N chained transfers and we
get a short packet before processing all N TRBs,
DWC3 will (conditionally) issue a XferComplete or
XferInProgress event and retire all TRBs from the
one which got a short packet to the last without
clearing their HWO bits.
This means SW must clear HWO bit manually, which
this patch is doing.
Cc: <stable@vger.kernel.org>
Cc: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When using SG lists, we would end up setting
request->actual to:
num_mapped_sgs * (request->length - count)
Let's fix that up by incrementing request->actual
only once.
Cc: <stable@vger.kernel.org>
Reported-by: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The whole Kconfig entries of the USB subsystem are surrounded with
"if USB_SUPPORT" ... "endif", so CONFIG_USB_SUPPORT=y is surely met
when these two Kconfig options are visible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PpU9
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-4.7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull more MFD fixes from Lee Jones:
"Apologies for missing these from the first pull request.
Final patches fixing Reset API change"
* tag 'mfd-fixes-4.7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
usb: dwc3: st: Use explicit reset_control_get_exclusive() API
phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
phy: miphy28lp: Inform the reset framework that our reset line may be shared
Looks like we lost all changes related to
commit 9522def400 ("usb: dwc3: core: cleanup IRQ resources") in host.c
when Felipe's next branch was merged into Greg's next branch.
Fixes 215db94818 ("Merge tag 'usb-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're making all reset line users specify whether their lines are
shared with other IP or they operate them exclusively. In this case
the line is exclusively used only by this IP, so use the *_exclusive()
API accordingly.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Use new reset_*_get_shared() variant to prevent reset line obtainment failure
- Fixes: 0b52297 ("reset: Add support for shared reset controls")
- Fix unintentional switch() fall-through into error path
- Fix uninitialised variable compiler warning
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mo7m
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
"Contained are some standard fixes and unusually an extension to the
Reset API. Some of those changes are required to fix a bug introduced
in -rc1, which introduces extra 'reset line checks' i.e. whether the
line is shared or not. If a line is shared and the new *_shared() API
is not used, the request fails with an error. This breaks USB in v4.7
for ST's platforms.
Admittedly, there are some patches contained in our (MFD/Reset)
immutable branch which are not true -fixes, but there isn't anything I
can do about that. Rest assured though, there aren't any API
'changes'. Everything is the same from the consumer's perspective.
- Use new reset_*_get_shared() variant to prevent reset line
obtainment failure (Fixes commit 0b52297f22: "reset: Add support
for shared reset controls")
- Fix unintentional switch() fall-through into error path
- Fix uninitialised variable compiler warning"
* tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: da9053: Fix compiler warning message for uninitialised variable
mfd: max77620: Fix FPS switch statements
phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
usb: dwc3: st: Inform the reset framework that our reset line may be shared
usb: host: ehci-st: Inform the reset framework that our reset line may be shared
usb: host: ohci-st: Inform the reset framework that our reset line may be shared
reset: TRIVIAL: Add line break at same place for similar APIs
reset: Supply *_shared variant calls when using *_optional APIs
reset: Supply *_shared variant calls when using of_* API
reset: Ensure drivers are explicit when requesting reset lines
reset: Reorder inline reset_control_get*() wrappers
On the STiH410 B2120 development board the MiPHY28lp shares its reset
line with the Synopsys DWC3 SuperSpeed (SS) USB 3.0 Dual-Role-Device
(DRD). New functionality in the reset subsystems forces consumers to
be explicit when requesting shared/exclusive reset lines.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here's the big pull request for Peripheral stack and
all related drivers.
This time around with 109 non-merge commits mostly
concentrated on drivers/usb/gadget/udc (41.5%) and
drivers/usb/dwc3 (28.1%).
There's a big rework on dwc3's transfer handling
which gave us almost 3x faster USB3 speeds with Mass
Storage on a particular test scenario I measured. We
are also removing platform_data from dwc3 after
converting all users to built-in properties instead.
For the Gadget API, we're just adding tracepoints to
aid debugging activities.
Other than these, there's the usual set of spelling
fixes, minor bug fixes and sparse warnings cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PT1e
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.8 merge window
Here's the big pull request for Peripheral stack and
all related drivers.
This time around with 109 non-merge commits mostly
concentrated on drivers/usb/gadget/udc (41.5%) and
drivers/usb/dwc3 (28.1%).
There's a big rework on dwc3's transfer handling
which gave us almost 3x faster USB3 speeds with Mass
Storage on a particular test scenario I measured. We
are also removing platform_data from dwc3 after
converting all users to built-in properties instead.
For the Gadget API, we're just adding tracepoints to
aid debugging activities.
Other than these, there's the usual set of spelling
fixes, minor bug fixes and sparse warnings cleanups.
This should allow xhci to remove handling of platform data.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It had changed to be suspend event for BIT6 in DEVT register from
version 2.30a and above. Thus this patch introduces one suspend
event handler to handle the suspend event.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implementations might use different IRQs for
host, gadget so use named interrupt resources
to allow device tree to specify the interrupts.
Following are the interrupt names
Peripheral Interrupt - peripheral
HOST Interrupt - host
Maintain backward compatibility for a single named
interrupt ("dwc3_usb3") for all interrupts as well as
unnamed interrupt at index 0 for all interrupts.
As platform_get_irq() variants are used, tackle
the -EPROBE_DEFER case as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It will be crash to stop gadget when the dwc3 device had been into suspend
state, thus we need to check if the dwc3 device had been into suspend state
when UDC try to stop gadget.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Because of recent changes to transfer handling on
DWC3, we will not get XferComplete unless we
completely fill up our TRB ring. This means that we
might get a Reset or Disconnect without getting a
XferComplete first.
In order to correctly release our allocated Transfer
Resource, we must issue ENDTRANSFER command whenever
dep->resource_index is valid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If there is a failure after pm_runtime_enable/get_sync()
we need to call pm_runtime_disable/put_sync().
Otherwise it will lead to an unbalanced pm_runtime_enable() on the
subsequent probe if the earlier probe bailed out due to -EPROBE_DEFER.
pm_runtime_get_sync() can fail as well so deal with that case too.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
it's clear now that when is_on=true, we must loop
until DWC3_DSTS_DEVCTRLHLT clears; while when
is_on=false we must loop until DWC3_DSTS_DEVCTRLHLT
gets set.
Instead of adding actual if() statements, we can
rely on XOR operation to evaluate to true only when
the above conditions apply. Then, we can move the
break condition back to the while() statement
together with our timeout check and the resulting
code is very compact and simpler to read.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of looping forever and forcing a return if
timeout reaches zero, we can just use timeout and
loop's break condition directly.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
testing shows that udelay() is unnecessary as
controller reaches Halted state almost
instantenously as can be seen by our timeout
variable never actually decrementing.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We shouldn't change a host-only dwc3 to gadget-only
if driver is built as gadget-only. Fix that up here.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's know that Intel's SoCs' dwc3 integration is
peripheral-only since Intel implements its own
portmux for role-swapping. In order to prevent dwc3
from ever registering and XHCI platform_device,
let's just set dr-mode to peripheral-only on Intel
SoCs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
'modify' is what the current action is called. Let's
rename it so it matches databook. While at that,
also make sure to add support 'init' action too.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now we can try to issue Update Transfer every time
gadget driver queues a new request. This will make
sure we keep controller's queue busy for as long as
possible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Let's only set LST bit when we run out of space in
our TRB ring. For all other cases, we keep LST bit
unset which will prevent constant allocation and
deallocation of endpoint transfer resources.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of relying on empty list of queued requests,
let's rely on the fact that we have a TRB being
processed right now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will be using this information to change how we
figure out when we need LST bit. For now, just
update our counters.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to SNPS databook, we need to pass transfer
resource on update transfer command, let's do it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No more users for it.
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This should allow the core driver to drop handling of
platform data and expect the platform specific details to
always come from properties.
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Huang Rui <ray.huang@amd.com>
CC: John Youn <John.Youn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
when passing strings to trace, we don't need the
trailing newline character. Trace already appends a
newline character automatically.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Don't make any decisions regarding VBUS session based on ID
status. That is best left to the OTG core.
Pass ID and VBUS events independent of each other so that OTG
core knows exactly what to do.
This makes dual-role with extcon work with OTG irq on OMAP platforms.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
TRM [1] recommends that POWERPRESENT bit must not be
set and left at it's default value of 0.
[1] OMAP542x TRM - http://www.ti.com/lit/pdf/swpu249
Section 23.11.4.5.1 Mailbox VBUS/ID Management
"Because PIPE powerpresent has a different meaning in host and in device mode,
and because of the redundancy with the UTMI signals, the controller ORes
together the appropriate PIPE and UTMI inputs to create its internal
VBUS status. For that reason, it is recommended to leave field
USBOTGSS_UTMI_OTG_STATUS[9] POWERPRESENT at its default value (=0), and only to
fill in the USB2 VBUS status fields in the same register."
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On OMAPs, OTG events come on the same IRQ so we need to share
this IRQ with the OTG device driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We intend to share this interrupt with the OTG driver an to ensure
that irqflags match for the shared interrupt handlers we use
request_threaded_irq()
If we don't use request_treaded_irq() then forced threaded irq will
set IRQF_ONESHOT and this won't match with the OTG IRQ handler's
IRQ flags.
NOTE: OTG IRQ handler is yet to be added. This is a preparatory step.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
GUCTL1 reg has some useful functions which can be
written by user. For rockchip platform, we set
GUCTL1.DEV_FORCE_20_CLK_FOR_30_CLK (bit26, applicable
for the core is programmed to operate in 2.0 device
only) to 1 in bootrom, and after start the kernel,
we want to check whether this bit can be reset to
default 0 after the core reset. Dump GUCTL1 reg from
debugfs is more convenient for us.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The DWC3_USB31_REVISION_110A macro uses an invalid constant name in its
definition. This is currently not used.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Correct the use of the DWC3_DSTS_XXX_SPEED and DWC3_DCFG_XXX_SPEED
macros. The wrong set of macros were being used in a few places.
This is only a cosmetic change as the values for both sets are
identical.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
From sparse:
warning: cast truncates bits from constant value (100 becomes 0)
The DWC3_TRB_NUM constant is too big for u8. Do the calculation a
slightly different way that should still be optimized out for the case
where DWC3_TRB_NUM == 256.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the trb->enqueue == trb->dequeue, then it could be full or empty.
This could also happen at TRB index 0, so modify the check to handle
that condition. At index 0, the previous TRB is the one just before the
link TRB.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The TRBs left calculation didn't account for the link TRB taking up one
spot.
If the trb_dequeue < trb_enqueue, then the result includes the link
TRB slot so it must be adjusted.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current calculation takes dep->trb_dequeue - dep->trb_enqueue to
find the TRB space left.
If you enqueue 1, that results in:
(u8) 0 - (u8) 1 = 0xff = 255 TRBs left.
This is correct if DWC3_TRB_NUM == 256.
If DWC3_TRB_NUM is less than 256 (but still a power of 2) you need to
mod the result by DWC3_TRB_NUM.
For example the same calculation with DWC3_TRB_NUM = 8, results in:
255 % 6 = 7 TRBs left.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If trbs_left == 0, we don't have any space left in the TRB ring so don't
prepare anything.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Clears out all the TRBs in the ring to clean up any stale data that
might be in them from the previous time the endpoint was enabled.
Also removed the existing clear of the LINK trb since the entire ring is
cleard just before.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the skipping of the link TRBS built-in to the increment operation.
This simplifies the code wherever we increment the trb index and ensures
that we never end up pointing to a link trb.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sparse complains even though it looks ok. Probably it cannot detect that
the wValue, wIndex, and wLength are declared __le16 due to the macro
magic.
Redeclare them as CPU endianness and make the conversion on assignment.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cleans up the sparse warning:
warning: dubious: x | !y
Since we do want a bitwise OR here, don't use a logical (true/false)
value. Probably is not a real issue but it cleans up the warning.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
u2sel and u2pel should be __le16. Doesn't fix any issue.
Found with sparse.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The wIndex passed in here is CPU endianness, but the function expects
little endian.
Found with sparse.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just like we did for endpoint commands, let's have a
single trace output for the command and its
status. This will improve trace readability
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just like we did for endpoint commands, let's use a
single return point for generic commands as
well. This aids readability.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of printing command's status with a separate
trace printout, let's print it within a single call.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of having infinite loop and always checking
timeout value as a break condition, we can just
decrement timeout inside while's condition.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
I really thought this would be useful, but as it
turns out, it creates more problems than fixes. The
amount of times we had to fix this because some
other commit shuffled things around and ended up
regressing this tiny little string manupulation...
Might as well remove it, since it has a negligible
added benefit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Improve trb tracing by showing trb flags, interrupts
trb type.
trb flags:
- h - hardware owner of descriptor
- l - last TRB
- c - chain buffers
- s - continue on short packet
interrupt flags:
- s - interrupt on short packet
- c - interrupt on complete
Capital letter means that bit is set, while
lowercase letter means bit is cleared.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will allow us to process several endpoints at a
time by making sure that we lock only shared
resources.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allow for dwc3-pci to reach D3 and enable pm_runtime
by providing dummy PM hooks. Without them, PCI
subsystem won't put device to D3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this patch implements the most basic pm_runtime
support for dwc3. Whenever USB cable is dettached,
then we will allow core to runtime_suspend.
Runtime suspending will involve completely tearing
down event buffers and require a full soft-reset of
the IP.
Note that a further optimization could be
implemented once we decide to support hibernation,
which is to allow runtime_suspend with cable
connected when bus is in U3. That's subject to a
separate patch, however.
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
when we call dwc3_gadget_giveback(), we end up
releasing our controller's lock. Another thread
could get scheduled and disable the endpoint,
subsequently setting dep->endpoint.desc to NULL.
In that case, we would end up dereferencing a NULL
pointer which would result in a Kernel Oops. Let's
avoid the problem by simply returning early if we
have a NULL descriptor.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit f3af36511e ("usb: dwc3: gadget: always
enable IOC on bulk/interrupt transfers") ended up
regressing Isochronous endpoints by clearing
DWC3_EP_BUSY flag too early, which resulted in
choppy audio playback over USB.
Fix that by partially reverting original commit and
making sure that we check for isochronous endpoints.
Fixes: f3af36511e ("usb: dwc3: gadget: always enable IOC
on bulk/interrupt transfers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As a micro-power optimization, let's only resume the
USB2 PHY if we're working on <=HIGHSPEED. If we're
gonna work on SUPERSPEED or SUPERSPEED+, there's no
point in resuming the USB2 PHY.
Fixes: 2b0f11df84 ("usb: dwc3: gadget: clear SUSPHY bit before ep cmds")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
by holding gadget's IRQ number in dwc->irq_gadget,
it'll be simpler to free_irq() and disable the IRQ
in case an IRQ fires while we are runtime suspended.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
now that we have re-factored dwc3_core_init() and
dwc3_core_exit() we can use them for suspend/resume
operations.
This will help us avoid some common mistakes when
patching code when we have duplicated pieces of code
doing the same thing.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The idea of this patch is for dwc3_core_init() to
abstract all the details about how to initialize
dwc3 and dwc3_core_exit() to do the same for
teardown.
With this, we can simplify suspend/resume operations
by a large margin and always know that we're going
to start dwc3 from a known starting point.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this patch is in preparation for some further
re-factoring in dwc3 initialization. No functional
changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By adding a pointer to endpoint registers' base
address, we can avoid using our controller-wide
struct dwc3 pointer for everything. At some point
this will allow us to have per-endpoint locks which
will, in turn, let us queue requests to separate
endpoints in parallel.
Because of this change our debugfs interface and io
accessors need to be changed accordingly.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In all call sites of dwc3_send_gadget_ep_cmd() we
already had a valid dep pointer, so instead of
passing dwc and dep->number, which would be used to
fetch the same pointer we already had, just pass dep
directly.
In other words, we're changing:
struct dwc3_ep *dep = dwc[dep->number];
to just passing struct dwc3_ep *dep as argument.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of using burst size to configure NUMP, we
should be using RxFIFO Size instead. DWC3 is smart
enough to know that it shouldn't burst in case burst
size is 0.
Reported-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To aid code readability, we're gonna split
__dwc3_gadget_kick_transfer() into its constituent
parts: scatter gather and linear buffers.
That way, it's easier to follow the code and focus
debug effort when one or the other fails.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of returning -EINVAL when someone calls
__dwc3_gadget_wakeup() in speeds > highspeed, let's
return 0. There are no problems for the driver for
calling it in superspeed as we cleanly just return.
This avoids an annoying WARN_ONCE() always
triggering during superspeed enumeration with LPM
enabled.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we send an endpoint command, we want that to
complete as soon as possible, so let's remove the
unnecessary udelay(1) call.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
sg_is_last() and list_is_last() will encode the
required information for the driver to make
decisions WRT CHN and LST bits.
While at that, also replace '1' with 'true' for
consistency.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
as it turns out, we don't need the extra 'start_new'
argument as that can be inferred from DWC3_EP_BUSY
flag.
Because of that, we can simplify
__dwc3_gadget_kick_transfer() by quite a bit, even
allowing us to prepare more TRBs unconditionally.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we're updating transfers, we can also prepare as
many TRBs as we can fit in the ring. Let's start
doing that.
This patch 'solves' a limitation of how many TRBs we
can prepare when we're getting close the end of the
ring. Instead driver to prepare only up to end of
the ring, we check if we have space to wrap around
the ring properly.
Note that this only happens when our enqueue and
dequeue pointers are equal (which is the case for
bulk endpoints after an XferComplete event).
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of trying hard to stay connected to the
host, it's best (and far easier) to disconnect from
the host already.
Anything relying on KEEP_CONNECT will just have that
ignored, but we don't have proper hibernation
implementation yet, so there are no regressions.
In any case, hibernation is only useful for runtime
PM, not system sleep.
While at that, also remove dwc3.dcfg which has been
rendered unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we will be re-using it for suspend/resume, so
instead of duplicating code, let's just re-factor
the functions so they can be re-used.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As of core revision 2.60a the recommended programming model is to set
the ClearPendIN bit when issuing a Clear Stall EP command for IN
endpoints. This is to prevent an issue where some (non-compliant) hosts
may not send ACK TPs for pending IN transfers due to a mishandled error
condition. Synopsys STAR 9000614252.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set USB3_FORCE_VBUSVALID when configured for USB_DR_MODE_PERIPHERAL
mode, as it is required to have a working setup.
This worked on the internal driver by relying on the reset
value of the syscfg register as the bits aren't explicity cleared
and set like the upstream driver.
Also add a comment about what setting this bit means.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3-exynos has two problems during init if the regulators are slow
to come up (for instance if the I2C bus driver is not on the initramfs)
and return probe deferral. First, every time this happens, the driver
leaks the USB phys created; they need to be deallocated on error.
Second, since the phy devices are created before the regulators fail,
this means that there's a new device to re-trigger deferred probing,
which causes it to essentially go into a busy loop of re-probing the
device until the regulators come up.
Move the phy creation to after the regulators have succeeded, and also
fix cleanup on failure. On my ODROID XU4 system (with Debian's initramfs
which doesn't contain the I2C driver), this reduces the number of probe
attempts (for each of the two controllers) from more than 2000 to eight.
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Fixes: d720f057fd ("usb: dwc3: exynos: add nop transceiver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the original DWC3_DCFG_NUMP() was always zero. It looks like the
intent was to shift first and then do the mask.
Fixes: 2a58f9c12b ('usb: dwc3: gadget: disable automatic calculation of ACK TP NUMP')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXIek2AAoJEIaOsuA1yqRE2+cP/iZzzRshn6atj4b0BaRzyk6k
acK6YNs8pBgJMt9FaVWhDOlCfa/8hg5W+6Z5Ovpx4WPyJdZbYkoxJ0ZJGKYjYZ/y
U8hUxpTJ2s2wZKXRKchzT90hQvNlHdg3u2okP2GK0Oa17/idcQf2w1+0Cscm/dqN
Ur5HgukLe31/MrcPr49OuLkahSPfHUQlOn8i4AZyBTh9L8ouzKDCvzUt2ABoCRLE
wPcMegJhks7FQ5fksXtLsfqhqAoHpYHlsZQcH35iV8wPdtSueAtZ8tS6t445XbX9
vEsFq1ovpBMYfl/dwV6RBZiQTjZiGWaIdjOZMUcpbD03yXE2IC6l+mtE/wuhlnHu
J0Rr4YmfS4g++J1+380NQGoreOBZ2u7pujQ4TAy399zsLD8LR3zOQK5IErILSfpO
m6p3ElkGuAyHJKmo4CysSspXnnNGBp/fuTkYdPM9IJRJCe0YwnF/zsQd0OrNZ/Pm
39f6woE2aBQaEzdn+3Nya9B2IWYi6SIheQXPg0HETX/hujZHJv1x758VO6+c7aeq
nlhRlxSe8u8DKryBG43+F+myHaIz1p0Y2O3MzIlvRv0yw87QevJ4pAWptdMITaMh
YpgSjDPw5y2z91AhK/Fv+AXswKaoWBc6EEzBirW6hQWllSp+7qWloA6vYXkdHDr7
QajUBeXzNgXF8JfIos5H
=7szP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.7 merge window
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
Now that we calculate DCFG.NUMP, we can disable
dwc3's automatic calculation so we maximize our
chances of very high throughtput through the use of
bursts.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
NumP field of DCFG register is used on NumP field of
ACK TP header and it tells the host how many packets
an endpoint can receive before waiting for
synchronization.
Documentation says it should be set to anything
<=bMaxBurst. Interestingly, however, this setting is
not per-endpoint how it should be (different
endpoints could have different burst sizes), but
things seem to work okay right now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
if Start Transfer command fails, let's try a little
harder to figure out why the command failed and give
slightly better return codes. This will be usefulf
or isochronous endpoints, at least, which could
decide to retry a given request.
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For convenience, passing the dwc3 platform device as a
parameter to dwc3_pci_quirks() function.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Setting the ACPI companion before calling dwc3_pci_quirks.
The ACPI companion will be set unconditionally as the
primary fwnode, overriding any previously set primary
fwnode. This will make sure that any build-in properties
added to the platform device will be added as the secondary
fwnode in cases where also ACPI companion exists.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case host sends us an unsupported test mode, we
*must* stall this request. This will tell the host
that the selector is invalid and we won't put the
controller in unsupported test modes which could
have undetermined side-effects.
Signed-off-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's a bunch of information in the debug register
set from dwc3 which is useful in some debugging
scenarios. Let's dump them out in endpoint-specific
directories and designated files.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This helper will be used later to convert trb type
into a human-readable string for debugfs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this helper will be used, initially, to dump space
of different queues and fifos in dwc3 to
debugfs. Later, it'll be used to issue remote wakeup
when we want to start a transfer and there's
something in a TX FIFO.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Debugfs init failure is not so important. We can continue our job on
this failure. Also no break need for debugfs_create_file call failure.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[felipe.balbi@linux.intel.com :
- remove out-of-memory message, we get that from OOM.
- switch dev_err() to dev_dbg() ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dma_status bit flag is set but never really used
so get rid of it.
Reported-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It makes no sense to interrupt in the middle of
chained transfer. This patch just makes sure we
don't do that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of limiting link TRB only to Isoc endpoints,
let's use it for all endpoint types, this way we are
more likely to transfer more data before a
XferComplete event.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By moving our % DWC3_NUM_TRB operation to the
increment helpers, the rest of the driver can be
simplified.
It's also a good practice to make sure we will have
a single place dealing with details about how to
increment our enqueue and dequeue pointers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add three little helpers which will aid in making
the code slightly easier to read. One helper
increments enqueue pointer, another increments
dequeue pointer and the last one tests if we're
dealing with the last TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of using a bitwise and, let's rely on the %
operator since that's a lot more clear. Also, GCC
will optimize % 256 to nothing anyway.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We *know* that we have 1 PAGE (4096 bytes) for our
TRB poll. We also know the size of each TRB and know
that we can fit 256 of them in one PAGE. By using a
u8 type we can make sure that:
enqueue++ % 256;
gets optimized to an increment only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This makes it clear that we're dealing with a queue
of TRBs. No functional changes. While at that, also
rename start_slot to first_trb_index for similar
reasons.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The DWC3 OMAP driver supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-omap.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some freescale QorIQ platforms require to disable receiver detection
in P3 for correct detection of USB devices. If GUSB3PIPECTL(DISRXDETINP3)
is set, Core will change PHY power state to P2 and then perform receiver
detection. After receiver detection, Core will change PHY power state to
P3. Same quirk would be added in dts file in future patches.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook says we should move link to U0
before issuing a Start Transfer command. We could
require the gadget driver to call
usb_gadget_wakeup() however I feel that changing all
gadget drivers to keep track of Link State and
conditionally call usb_gadget_wakeup() would be far
too much work. For now we will handle this at the
UDC level, but at some point composite.c should be
one handling this.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook 2.60a has a note that if we're
sending an endpoint command we _must_ make sure that
DWC3_GUSB2PHY(n).SUSPHY bit is cleared.
This patch implements that particular detail.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_send_gadget_ep_cmd() had three return
points. That becomes a pain to track when we need to
debug something or if we need to add more code
before returning.
Let's combine all three return points into a single
one just by introducing a local 'ret' variable.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we don't plan on using multiple event buffers, but
if we find a good use case for it, this little trick
will help us avoid a loop in hardirq handler looping
for each and every event buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget controller might not be always active during system
suspend/resume as gadget driver might not have yet been loaded or
might have been unloaded prior to system suspend.
Check if we're active and only then perform
necessary actions during suspend/resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc->regset is allocated on dwc3_debugfs_init, and should
be released on init failure or dwc3_debugfs_exit. Btw,
The line "dwc->root = NULL" is unnecessary, so remove it.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[ felipe.balbi@linux.intel.com : add another err label for the new
error condition ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we need to power off the PHY during suspend and
power it back on during resume.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: fix call to usb_phy_set_suspend() in dwc3_suspend()]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Even if pm_runtime_get*() fails, we *MUST* call
pm_runtime_put_sync() before disabling PM.
While at it, remove superfluous dwc3_omap_disable_irqs()
in error path.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: patch description updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we will be using a single event buffer and that
renders ev_buffs array unnecessary. Let's remove it
in favor of a single pointer to a single event
buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We never, ever route any of the other event buffers
so we might as well drop support for them.
Until someone has a real, proper benefit for
multiple event buffers, we will rely on a single
one. This also helps reduce memory footprint of
dwc3.ko which won't allocate memory for the extra
event buffers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
request_list and req_queued were, well, weird naming
choices.
Let's give those better names and call them,
respectively, pending_list and started_list. These
new names better reflect what these lists are
supposed to do.
While at that also rename req->queued to req->started.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
previously we were using a maximum of 32 TRBs per
endpoint. With each TRB being 16 bytes long, we were
using 512 bytes of memory for each endpoint.
However, SLAB/SLUB will always allocate PAGE_SIZE
chunks. In order to better utilize the memory we
allocate and to allow deeper queues for gadgets
which would benefit from it (g_ether comes to mind),
let's increase the maximum to 256 TRBs which rounds
up to 4096 bytes for each endpoint.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
CSP bit of TRB Control is useful for protocols such
CDC EEM/ECM/NCM where we're transferring in blocks
of MTU-sized requests (usually MTU is 1500 bytes).
We know we will always have a short packet after two
(for HS) wMaxPacketSize packets and, usually, we
will have a long(-ish) queue of requests (for our
g_ether gadget, we have at least 10
requests).
Instead of always stopping the queue processing to
interrupt, giveback and restart, let's tell dwc3 to
interrupt but continue processing following request
if we have anything already pending in the queue.
This gave me a considerable improvement of 40% on my
test setup.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
That FIFO resizing logic was added to support OMAP5
ES1.0 which had a bogus default FIFO size. I can't
remember the exact size of default FIFO, but it was
less than one bulk superspeed packet (<1024) which
would prevent USB3 from ever working on OMAP5 ES1.0.
However, OMAP5 ES1.0 support has been dropped by
commit aa2f4b16f8 ("ARM: OMAP5: id: Remove ES1.0
support") which renders FIFO resizing unnecessary.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Keystone 2 supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-keystone.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Cc: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
BXT-M is a Intel Broxton SoC based platform with unique PCI ID.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We were exitting the function before actually
renaming anything. While at that, also always leave
control endpoint un-renamed.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's a requirement that we release controller's lock
while calling gadget API function pointers. This
patch just fixes that long standing bug.
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Synopsys Databook, we shouldn't be
relying on GCTL.CORESOFTRESET bit as that's only for
debugging purposes. Instead, let's use DCTL.CSFTRST
if we're OTG or PERIPHERAL mode.
Host side block will be reset by XHCI driver if
necessary. Note that this reduces amount of time
spent on dwc3_probe() by a long margin.
We're still gonna wait for reset to finish for a
long time (default to 1ms max), but tests show that
the reset polling loop executed at most 19 times
(modprobe dwc3 && modprobe -r dwc3 executed 1000
times in a row).
Suggested-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
new device support in terms of LoC, but there has been some cleanup
in the core as well as the usual minor clk additions to various
drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a minor
refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABCAAGBQJW8fPZAAoJENidgRMleOc9sc0P/2b4k8FiFwjMXiiXI1rcEjiz
ZjeVxzyAcwBiYoL8a2XONd+pihjLNcAbDbjk8SGUzmKDDz7elQbrhby/6o1dPlW/
fQEQFa8Xa8zhZgidO1AFc1DmIcPg/u/Z58wHbjIcqDjvzKA63213Ud34NJsRtF6y
+EJrIUZiTtj5q1pJgDmqlOv6ImmQtgW/AN51vNXCNNCyS9OsSgQm0DK5/f485HNc
2y5NE5hpijso69HFet5chuT3DiDLz/0dxmgCm/w9CRRzkHxYl3lxV/v07B+rZBo5
cWplFfvJqX7PvQtcP0sPPzZUfGT/vOeTboWprQwI4R3RObS18xLqlq6DEvOTmnqW
Jh+9uNBq4+kwSz5GcYjpwvj7+W0FPgIaBVRHrEW9qeXkgDpYloPtnEt8C8GmO6Bt
O0bgIzETq9mnRTA+VesIfjmTa4IYRDDUoDwGTw5CnW3jaZmtYJh8GhgZulMfPfyK
vfWQkY2OesXFwct0rU8tFiswTPeTRgXqL3AsPYjTPAHx1kfBpvfOQTCzzT7eSBr7
jykd9EXsXrYb/rpIxW7j6KjPpaWu+EouK06wc4TIBGrrWVTIV0ZvybzOBgf0FnpS
UDx87OyQb8x9TDMrfKf6bmJyly8y1dXkutFYY4XKIGUydlXIf0kn7AnIXW6SR7mX
fTEdLFMZ03ViCojtah5r
=bZFY
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The clk changes for this release cycle are mostly dominated by new
device support in terms of LoC, but there has been some cleanup in the
core as well as the usual minor clk additions to various drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a
minor refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction
dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (197 commits)
clk: bcm2835: fix check of error code returned by devm_ioremap_resource()
clk: renesas: div6: use RENESAS for #define
clk: renesas: Rename header file renesas.h
clk: max77{686,802}: Remove CLK_IS_ROOT
clk: versatile: Remove CLK_IS_ROOT
clk: sunxi: Remove use of variable length array
clk: fixed-rate: Remove CLK_IS_ROOT
clk: qcom: Remove CLK_IS_ROOT
doc: dt: add documentation for lpc1850-creg-clk driver
clk: add lpc18xx creg clk driver
clk: lpc32xx: fix compilation warning
clk: xgene: Add missing parenthesis when clearing divider value
clk: mb86s7x: Remove CLK_IS_ROOT
clk: x86: Remove clkdev.h and clk.h includes
clk: x86: Remove CLK_IS_ROOT
clk: mvebu: Remove CLK_IS_ROOT
clk: renesas: move drivers to renesas directory
clk: si5{14,351,70}: Remove CLK_IS_ROOT
clk: scpi: Remove CLK_IS_ROOT
clk: s2mps11: Remove CLK_IS_ROOT
...
Check that dwc->maximum_speed is set to a valid value. Also add an error
when we use it later if we encounter an invalid value.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Enable SuperSpeedPlus by programming the DCFG.speed and after
enumerating, set gadget->speed appropriately.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the maximum_speed is not set, set it to a known value, either
SuperSpeed or SuperSpeedPlus based on the type of controller we are
using. If we are on DWC_usb31 controller, check the PHY interface to see
if it is capable of SuperSpeedPlus.
Also this check is moved after dwc3_core_init() so that we can check
dwc->revision.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Update various places where the speed is checked so that it takes into
account SuperSpeedPlus properly.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Update various registers fields definitions for the DWC_usb31 controller
for SuperSpeedPlus support.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add a convenience function to check if the controller is DWC_usb31.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The check for < 0 is impossible now that
of_clk_get_parent_count() returns an unsigned int. Simplify the
code and update the types.
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda61871 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda61871 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch is needed in order to pass one test case
defined in the OTG Automated Compliance Test specification.
Specification location:
http://www.usb.org/developers/onthego/otgeh_compliance_plan_1_2.pdf
This test case uses PET Tool, and PET Tool is one USB hardware
equipment provided by MQP Electronics.
Test case id is 6.8.3 B-UUT Bypass Capacitance.
We must set this otg flag in order to be able to return OTG
descriptor during enumeration, otherwise this test case with
failed with below error: "Get OTG descriptor request stalled".
Signed-off-by: Jianqiang Tang <jianqiang.tang@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
if we have a !PM kernel build, our runtime
suspend/resume callbacks will be left defined but
unused. Add a ifdef CONFIG_PM guard.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the request->length is zero, a ZLP should already be sent due to that
and another ZLP is not needed to terminate the transfer.
Fixes: 04c03d10e5 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
