Lane clock handling can be simplified by using the clk_bulk APIs. So let's
make use of them. This also get's rid of the clock validation in the driver
as kernel should just rely on the firmware (DT/ACPI) to provide the clocks
required for proper functioning.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-2-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Start from HW ver 5, a spare register in UFS host controller is added and
used to indicate the UFS device version. The spare register is populated by
bootloader for now, but in future it will be populated by HW automatically
during link startup with its best efforts in any boot stage prior to Linux.
During host driver init, read the spare register, if it is not populated
with a UFS device version, go ahead with the dual init mechanism. If a UFS
device version is in there, use the UFS device version together with host
controller's HW version to decide the proper PHY gear which should be used
to configure the UFS PHY without going through the second init.
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-9-git-send-email-quic_cang@quicinc.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ufs_qcom_power_up_sequence(), check return value of phy_set_mode_ext()
and stop proceeding if phy_set_mode_ext() fails.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-8-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since HW ver 4, max HS gear can be get from UFS host controller's register,
use the max HS gear as the initial PHY gear instead of UFS_HS_G2, so that
we don't need to update the hard code for newer targets in future.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-7-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Qcom UFS hosts, with HW ver 5, can only support up to HS-G5 Rate-A due to
HW limitations. If the HS-G5 PHY gear is used, update host_params->hs_rate
to Rate-A, so that the subsequent power mode changes shall stick to Rate-A.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-6-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During host driver init, the phy_gear is set to the minimum supported gear
(HS_G2). Then, during the first power mode change, the negotiated gear, say
HS-G4, is updated to the phy_gear variable so that in the second init the
updated phy_gear can be used to program the PHY.
But the current code only allows update the phy_gear to a higher value. If
one wants to start the first init with the maximum support gear, say HS-G4,
the phy_gear is not updated to HS-G3 if the device only supports HS-G3.
The original check added there is intend to make sure the phy_gear won't be
updated when gear is scaled down (during clock scaling). Update the check
so that one can start the first init with the maximum support gear without
breaking the original fix by checking the ufshcd_state, that is, allow
update to phy_gear only if power mode change is invoked from
ufshcd_probe_hba().
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-5-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Setup host power mode and its limitations during UFS host driver init to
avoid repetitive work during every power mode change.
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Co-developed-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-4-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ufs_qcom_pwr_change_notify(), host_params.hs_rate has been set to
PA_HS_MODE_B by ufshcd_init_host_param(), hence remove the duplicated line
of work. Meanwhile, removed the macro UFS_QCOM_LIMIT_HS_RATE as it is only
used here.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-3-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Structure ufs_dev_params is actually used in UFS host drivers to declare
host specific power mode parameters, like ufs_<vendor>_params or host_cap,
which makes the code not very straightforward to read. Rename the structure
ufs_dev_params to ufs_host_params and unify the declarations in all drivers
to host_params.
In addition, rename the two functions ufshcd_init_pwr_dev_param() and
ufshcd_get_pwr_dev_param() which work based on the ufs_host_params to
ufshcd_init_host_params() and ufshcd_negotiate_pwr_params() respectively to
avoid confusions.
This change does not change any functionalities or logic.
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-2-git-send-email-quic_cang@quicinc.com
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
OPP support added by commit 72208ebe18 ("scsi: ufs: core: Add support for
parsing OPP") doesn't update the min_freq and max_freq of each clock in
'struct ufs_clk_info'.
But these values are used by the host drivers internally for controller
configuration. When the OPP support is enabled in devicetree, these values
will be 0, causing boot issues on the respective platforms.
So add support to parse the min_freq and max_freq of all clocks while
parsing the OPP table.
Fixes: 72208ebe18 ("scsi: ufs: core: Add support for parsing OPP")
Co-developed-by: Manish Pandey <quic_mapa@quicinc.com>
Signed-off-by: Manish Pandey <quic_mapa@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20231208131331.12596-1-quic_nitirawa@quicinc.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
OPP framework can be used to scale the clocks along with other entities
such as regulators, performance state etc... So let's add support for
parsing OPP from devicetree. OPP support in devicetree is added through the
"operating-points-v2" property which accepts the OPP table defining clock
frequency, regulator voltage, power domain performance state etc...
Since the UFS controller requires multiple clocks to be controlled for
proper working, devm_pm_opp_set_config() has been used which supports
scaling multiple clocks through custom ufshcd_opp_config_clks() callback.
It should be noted that the OPP support is not compatible with the old
"freq-table-hz" property. So only one can be used at a time even though
the UFS core supports both.
Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231012172129.65172-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "attr" pointer points to an offset into the "host" struct so it can't
be NULL. Delete the if statement and pull the code in a tab.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/fe3b8fcd-64a7-4887-bddd-32239a88a6a3@moroto.mountain
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The acpi_evaluate_dsm_typed() provides a way to check the type of the
object evaluated by _DSM call. Use it instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231002135125.2602895-1-andriy.shevchenko@linux.intel.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The DMA alignment for the Exynos controller follows directly from the PRDT
segment size configured in ufs-exynos.c. Hence, move the DMA alignment code
into the Exynos driver source code.
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230921192335.676924-3-bvanassche@acm.org
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To
improve here there is a quest to make the remove callback return void. In
the first step of this quest all drivers are converted to .remove_new()
which already returns void. Eventually after all drivers are converted,
.remove_new() is renamed to .remove().
All platform drivers below drivers/ufs/ unconditionally return zero in
their remove callback and so can be converted trivially to the variant
returning void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230917145722.1131557-1-u.kleine-koenig@pengutronix.de
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nitin Rawat <quic_nitirawa@quicinc.com> says:
This patch series adds programming support for Qualcomm UFS V4 and
above to align avoid with Hardware Specification. This patch series
will address stability and performance issues.
In this patch series below changes are taken care.
1) Register layout for DME_VS_CORE_CLK_CTRL has changed for v4 and above.
2) Adds Support to configure PA_VS_CORE_CLK_40NS_CYCLES attibute for UFS V4
and above.
3) Adds Support to configure multiple unipro frequencies like 403MHz,
300MHz, 202MHz, 150 MHz, 75Mhz, 37.5 MHz for Qualcomm UFS Controller V4
and above.
4) Allow configuration of SYS1CLK_1US_REG for UFS V4 and above.
Link: https://lore.kernel.org/r/20230905052400.13935-1-quic_nitirawa@quicinc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "hs_gear" variable is used to cache the gear setting for the PHY that
will be used during ufs_qcom_power_up_sequence(). But it creates ambiguity
with the gear setting used by the ufshcd driver.
So let's rename it to "phy_gear" to make it explicit that this variable
caches the gear setting for the PHY.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230908145329.154024-2-manivannan.sadhasivam@linaro.org
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Tested-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "hs_gear" variable is used to program the PHY settings (submode) during
ufs_qcom_power_up_sequence(). Currently, it is being updated every time the
agreed gear changes. Due to this, if the gear got downscaled before suspend
(runtime/system), then while resuming, the PHY settings for the lower gear
will be applied first and later when scaling to max gear with REINIT, the
PHY settings for the max gear will be applied.
This adds a latency while resuming and also really not needed as the PHY
gear settings are backwards compatible i.e., we can continue using the PHY
settings for max gear with lower gear speed.
So let's update the "hs_gear" variable _only_ when the agreed gear is
greater than the current one. This guarantees that the PHY settings will be
changed only during probe time and fatal error condition.
Due to this, UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH can now be skipped
when the PM operation is in progress.
Cc: stable@vger.kernel.org
Fixes: 96a7141da3 ("scsi: ufs: core: Add support for reinitializing the UFS device")
Reported-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230908145329.154024-1-manivannan.sadhasivam@linaro.org
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Tested-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SYS1CLK_1US represents the required number of system 1-clock cycles for one
microsecond. UFS Host Controller V4.0 and above mandates to write
SYS1CLK_1US_REG register and also these timer configuration needs to be
called from clk scaling pre ops as per HPG.
Refactor ufs_qcom_cfg_timers and add the below code support to align
with HPG.
a)Configure SYS1CLK_1US_REG for UFS V4 and above.
b)Introduce a new argument is_pre_scale_up for ufs_qcom_cfg_timers
to configure SYS1CLK_1US for max freq during prescale and link startup
condition.
c)Move ufs_qcom_cfg_timers from clk scaling post change ops
to clk scaling pre change ops.
Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20230905052400.13935-6-quic_nitirawa@quicinc.com
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently CORE_CLK_1US_CYCLES, PA_VS_CORE_CLK_40NS_CYCLES are configured
in clk scaling post change ops. This is not aligning to HPG.
Move this to clk scaling pre change ops to align completely with hardware
specification.
Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20230905052400.13935-5-quic_nitirawa@quicinc.com
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PA_VS_CORE_CLK_40NS_CYCLES attribute represents the required number of
Qunipro core clock for 40 nanoseconds. For UFS host controller V4 and above
PA_VS_CORE_CLK_40NS_CYCLES needs to be programmed as per frequency of
unipro core clk of UFS host controller.
Add Support to configure PA_VS_CORE_CLK_40NS_CYCLES for Controller V4 and
above to align with the hardware specification and to avoid functionality
issues like h8 enter/exit failure, command timeout.
Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20230905052400.13935-4-quic_nitirawa@quicinc.com
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Qualcomm UFS Controller V4 and above supports multiple unipro frequencies
like 403MHz, 300MHz, 202MHz, 150 MHz, 75Mhz, 37.5 MHz. Current code
supports only 150MHz and 75MHz which have performance impact due to low UFS
controller frequencies.
For targets which supports frequencies other than 150 MHz and 75 Mhz, needs
an update of MAX_CORE_CLK_1US_CYCLES to match the configured frequency to
avoid functionality issues. Add multiple frequency support for
MAX_CORE_CLK_1US_CYCLES based on the frequency configured.
Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20230905052400.13935-3-quic_nitirawa@quicinc.com
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS Controller V4 and above, the register layout for DME_VS_CORE_CLK_CTRL
register has changed. MAX_CORE_CLK_1US_CYCLES offset has changed from 0 to
0x10 and length of attrbute is changed from 8bit to 12bit.
Add support to configure MAX_CORE_CLK_1US_CYCLES for UFS V4 and above as
per new register layout.
Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20230905052400.13935-2-quic_nitirawa@quicinc.com
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bindings do not allow vdd-hba-max-microamp property and the driver does not
use it (does not control load of vdd-hba supply). Skip looking for this
property to avoid misleading dmesg messages:
ufshcd-qcom 1d84000.ufs: ufshcd_populate_vreg: unable to find vdd-hba-max-microamp
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230906113302.201888-1-krzysztof.kozlowski@linaro.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The qunipro_g4_sel clear is also needed for new platforms with major
version > 5. Fix the version check to take this into account.
Fixes: 9c02aa24bf ("scsi: ufs: ufs-qcom: Clear qunipro_g4_sel for HW version major 5")
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230821-topic-sm8x50-upstream-ufs-major-5-plus-v2-1-f42a4b712e58@linaro.org
Reviewed-by: "Bao D. Nguyen" <quic_nguyenb@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert ufshcd_pltfrm_init() over to use dev_err_probe() to avoid the
following log message on bootup due to an -EPROBE_DEFER return code:
ufshcd-qcom 1d84000.ufs: Initialization failed
While this line is changed, let's also go ahead and add the error code to
the message as well.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/20230814184352.200531-3-bmasney@redhat.com
Reviewed-by: "Bao D. Nguyen" <quic_nguyenb@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To ensure that the PCI based QEMU UFS device properly works with Linux,
register the device ID (0x0013) and vendor ID (0x1b36) of QEMU UFS device.
QEMU UFS will enable testing of the UFS driver inside a virtual machine on
systems without UFS host controller. It can also be used to preemptively
implement and test new features before the real device is created.
The new QEMU UFS device can be found at:
https://lore.kernel.org/qemu-devel/20230727155239.GA979354@fedora
Signed-off-by: Jeuk Kim <jeuk20.kim@samsung.com>
Link: https://lore.kernel.org/r/20230807013726epcms2p1c604cb8e98680aebebb7cc5ab2d580f5@epcms2p1
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Should use devm_kzalloc() for struct ufs_renesas_priv because the
.initialized should be false as default.
Fixes: d69520288e ("scsi: ufs: ufs-renesas: Add support for Renesas R-Car UFS controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20230803081812.1446282-1-yoshihiro.shimoda.uh@renesas.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche <bvanassche@acm.org> says:
Hi Martin,
This patch includes the following changes, none of which should change the
functionality of the UFS host controller driver:
- Improve the kernel-doc headers further.
- Fix multiple W=2 compiler warnings.
- Simplify ufshcd_abort_all().
- Simplify the code for creating and parsing UFS Transport Protocol (UTP)
headers.
Please consider this patch series for the next merge window.
Thanks,
Bart.
Link: https://lore.kernel.org/r/20230727194457.3152309-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use 'Return:' to document the return value instead of 'Returns' as required
by the kernel-doc documentation.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230727194457.3152309-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Qcom SoCs require scaling the interconnect paths for proper working of the
peripherals connected through interconnects. Even for accessing the UFS
controller, someone should setup the interconnect paths. So far, the
bootloaders used to setup the interconnect paths before booting Linux as
they need to access the UFS storage for things like fetching boot firmware.
But with the advent of multi boot options, bootloader nowadays like in
SA8540p SoC do not setup the interconnect paths at all.
So trying to configure UFS in the absence of the interconnect path
configuration results in a boot crash.
To fix this issue, and also to dynamically scale the interconnects (UFS-DDR
and CPU-UFS), interconnect API support is added to the Qcom UFS driver.
With this support, the interconnect paths are scaled dynamically based on
the gear configuration.
During the early stage of ufs_qcom_init(), ufs_qcom_icc_init() will setup
the paths to max bandwidth to allow configuring the UFS registers. Touching
the registers without configuring the icc paths would result in a crash.
However, we don't really need to set max vote for the icc paths as any
minimal vote would suffice. But the max value would allow initialization to
be done faster. After init, the bandwidth will get updated using
ufs_qcom_icc_update_bw() based on the gear and lane configuration.
The bandwidth values defined in ufs_qcom_bw_table struct are taken from
Qcom downstream vendor devicetree source and are calculated as per the
UFS3.1 Spec, Section 6.4.1, HS Gear Rates. So it is fixed across platforms.
Cc: Brian Masney <bmasney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230731145020.41262-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since there are enums available for UFS gears, let's add enums for lanes as
well to maintain uniformity.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230731145020.41262-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent change removed the only user of a local variable that needs to now
also be removed:
drivers/ufs/host/ufs-qcom.c: In function 'ufs_qcom_mcq_esi_handler':
drivers/ufs/host/ufs-qcom.c:1652:31: error: unused variable 'host' [-Werror=unused-variable]
Fixes: 8f2b78652d ("scsi: ufs: qcom: Get queue ID from MSI index in ESI handler")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/llvm/64c00cd4.630a0220.6ad79.0eac@mx.google.com/
Link: https://lore.kernel.org/r/20230724122029.1430482-1-arnd@kernel.org
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Devfreq uses the default DEVFREQ_TIMER_DEFERRABLE mode which uses the
deferred timer for scheduling the devfreq load monitor function. This
causes the load monitoring to be done only with non-idle CPUs and not
making use of the idle CPUs.
Hence, use the DEVFREQ_TIMER_DELAYED mode which uses the delayed timer
thereby making use of idle CPUs as well for load monitoring.
Co-developed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20230720093446.30697-1-quic_nitirawa@quicinc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus. As
part of that merge prepping Arm DT support 13 years ago, they "temporarily"
include each other. They also include platform_device.h and of.h. As a
result, there's a pretty much random mix of those include files used
throughout the tree. In order to detangle these headers and replace the
implicit includes with struct declarations, users need to explicitly
include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714175018.4064957-1-robh@kernel.org
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no need to call the dev_err() function directly to print a custom
message when handling an error from either the platform_get_irq() or
platform_get_irq_byname() functions as both are going to display an
appropriate error message in case of a failure.
./drivers/ufs/host/ufs-mediatek.c:864:3-10: line 864 is redundant because platform_get_irq() already prints an error
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=5846
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230712064832.44188-1-yang.lee@linux.alibaba.com
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
platform_msi_domain_alloc_irqs() does not always get consecutive IRQ
numbers, hence queue IDs calculated out from IRQ numbers may be incorrect
if we assume IRQ numbers are consecutive. Fix this by passing msi_desc to
ESI handler to use msi_desc->msi_index as queue ID.
Co-developed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Ziqi Chen <quic_ziqichen@quicinc.com>
Link: https://lore.kernel.org/r/1689062349-77385-1-git-send-email-quic_ziqichen@quicinc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When TI UFS host controller driver is built as kernel module it is not
getting auto-loaded due to missing aliases in modules.
Add device tree related aliases.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230710094801.183149-1-u-kumar1@ti.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add UFS MCQ vops and IRQ handler for MediaTek platform. PM flow is fixed
accordingly.
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Link: https://lore.kernel.org/r/20230701124442.10489-3-powen.kao@mediatek.com
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When RESET_CONTROLLER is not set, kconfig complains about missing
dependencies for RESET_TI_SYSCON, so add the missing dependency just as is
done above for SCSI_UFS_QCOM.
Silences this kconfig warning:
WARNING: unmet direct dependencies detected for RESET_TI_SYSCON
Depends on [n]: RESET_CONTROLLER [=n] && HAS_IOMEM [=y]
Selected by [m]:
- SCSI_UFS_MEDIATEK [=m] && SCSI_UFSHCD [=y] && SCSI_UFSHCD_PLATFORM [=y] && ARCH_MEDIATEK [=y]
Fixes: de48898d0c ("scsi: ufs-mediatek: Create reset control device_link")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: lore.kernel.org/r/202306020859.1wHg9AaT-lkp@intel.com
Link: https://lore.kernel.org/r/20230701052348.28046-1-rdunlap@infradead.org
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Peter Wang <peter.wang@mediatek.com>
Cc: Paul Gazzillo <paul@pgazz.com>
Cc: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Cc: linux-scsi@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add PCI ID to support Intel Arrow Lake, same as MTL (Intel Meteor Lake).
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230613170327.61186-1-adrian.hunter@intel.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that there is a new dedicated ICE driver, drop the ufs-qcom-ice and use
the new ICE api provided by the Qualcomm soc driver ice. The platforms that
already have ICE support will use the API as library since there will not
be a devicetree node, but instead they have reg range. In this case, the
of_qcom_ice_get will return an ICE instance created for the consumer's
device. But if there are platforms that do not have ice reg in the consumer
devicetree node and instead provide a dedicated ICE devicetree node, the
of_qcom_ice_get will look up the device based on qcom,ice property and will
get the ICE instance registered by the probe function of the ice driver.
The ICE clock is now handle by the new driver. This is done by enabling it
on the creation of the ICE instance and then enabling/disabling it on UFS
runtime resume/suspend.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230612192847.1599416-3-abel.vesa@linaro.org
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable UFSHCD_QUIRK_MCQ_BROKEN_RTC for MediaTek host.
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Link: https://lore.kernel.org/r/20230612085817.12275-5-powen.kao@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable UFSHCD_QUIRK_MCQ_BROKEN_INTR for MediaTek host.
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Link: https://lore.kernel.org/r/20230612085817.12275-4-powen.kao@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All UFS host drivers call ufshcd_shutdown(). Hence, instead of calling
ufshcd_shutdown() from the host driver .shutdown() callback, inline that
function into ufshcd_wl_shutdown().
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230524203659.1394307-5-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation for adding MCQ error handler support, update the MCQ code to
use the ufshcd_mcq_poll_cqe_lock() in interrupt context instead of using
ufshcd_mcq_poll_cqe_nolock(). This is to keep synchronization between MCQ
interrupt and error handler contexts because both need to access the MCQ
hardware in separate contexts.
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Link: https://lore.kernel.org/r/6ae727ad2a4040469b8f0632b55e0577d80da11b.1685396241.git.quic_nguyenb@quicinc.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Tested-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do not open code SZ_x.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20230531070009.4593-1-avri.altman@wdc.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Keoseong Park <keosung.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is already a test for "if (val == state)" earlier so it's not
possible here. Delete the dead code.
Fixes: 9006e3986f ("scsi: ufs-mediatek: Do not gate clocks if auto-hibern8 is not entered yet")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/68fce64f-4970-45f1-807e-6c0eecdfcdc2@kili.mountain
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr() does not make any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here).
drivers/ufs/host/ufs-hisi.c:561:34: error: ‘ufs_hisi_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230310214435.275127-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr() does not make any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here).
drivers/ufs/host/ufs-exynos.c:1738:34: error: ‘exynos_ufs_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230310214435.275127-2-krzysztof.kozlowski@linaro.org
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver can be built on ACPI and its .of_match_table uses
of_match_ptr(), thus annotate the actual table as maybe unused.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230310214435.275127-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Smatch static checker reported:
drivers/ufs/host/ufs-qcom.c:1469
ufs_qcom_mcq_config_resource() info: returning a literal zero is
cleaner
Fix the above warning by returning in place instead of a jump to a label.
Also remove the usage of devm_kfree() as it's unnecessary in this function.
Fixes: c263b4ef73 ("scsi: ufs: core: mcq: Configure resource regions")
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Link: https://lore.kernel.org/r/3ebd2582af74b81ef7b57149f57c6a3bf0963953.1677721229.git.quic_asutoshd@quicinc.com
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix an error case in ufs_qcom_mcq_config_resource(), where the return value
is set to 0 before passing it to PTR_ERR.
This led to Smatch warning:
drivers/ufs/host/ufs-qcom.c:1455 ufs_qcom_mcq_config_resource() warn:
passing zero to 'PTR_ERR'
Fixes: c263b4ef73 ("scsi: ufs: core: mcq: Configure resource regions")
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Link: https://lore.kernel.org/r/94ca99b327af634799ce5f25d0112c28cd00970d.1677721072.git.quic_asutoshd@quicinc.com
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "dev_req_params" pointer points to inside the middle of a struct so it
can't be NULL. Removing this impossible condition is nice because now we
don't need to consider the correct error code for that situation.
Link: https://lore.kernel.org/r/Y/yA3niWUcGYgBU8@kili
Fixes: f06fcc7155 ("scsi: ufs-qcom: add QUniPro hardware support and power optimizations")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates that missed the first pull, mostly because of needing more
soak time. Driver updates (zfcp, ufs, mpi3mr, plus two ipr bug
fixes), an enclosure services (ses) update (mostly bug fixes) and
other minor bug fixes and changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZAJf2SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWYeAP9u6umX
5Trq6mtfdPyhSxIhgD6AwJDgVkeApSKAHZRu0AD/dfMTQmeaJory4LD4JW+uAgVl
yFPVz9VPlKTiaM2lwUI=
=BKzr
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Updates that missed the first pull, mostly because of needing more
soak time.
Driver updates (zfcp, ufs, mpi3mr, plus two ipr bug fixes), an
enclosure services (ses) update (mostly bug fixes) and other minor bug
fixes and changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
scsi: zfcp: Trace when request remove fails after qdio send fails
scsi: zfcp: Change the type of all fsf request id fields and variables to u64
scsi: zfcp: Make the type for accessing request hashtable buckets size_t
scsi: ufs: core: Simplify ufshcd_execute_start_stop()
scsi: ufs: core: Rely on the block layer for setting RQF_PM
scsi: core: Extend struct scsi_exec_args
scsi: lpfc: Fix double word in comments
scsi: core: Remove the /proc/scsi/${proc_name} directory earlier
scsi: core: Fix a source code comment
scsi: cxgbi: Remove unneeded version.h include
scsi: qedi: Remove unneeded version.h include
scsi: mpi3mr: Remove unneeded version.h include
scsi: mpi3mr: Fix missing mrioc->evtack_cmds initialization
scsi: mpi3mr: Use number of bits to manage bitmap sizes
scsi: mpi3mr: Remove unnecessary memcpy() to alltgt_info->dmi
scsi: mpi3mr: Fix issues in mpi3mr_get_all_tgt_info()
scsi: mpi3mr: Fix an issue found by KASAN
scsi: mpi3mr: Replace 1-element array with flex-array
scsi: ipr: Work around fortify-string warning
scsi: ipr: Make ipr_probe_ioa_part2() return void
...
As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmPtSN8ACgkQmmx57+YA
GNkOSw/+JS5tElm/ZP7c3uWYp6uwvcb0jUlKW/U3aCtPiPEcYDLEqIEXwcNdaDMh
m4rW3GYlW0IRL3FsyuYkSLx+EIIUIfs40wldYXJOqRDj0XasndiloIwltOQJGfd9
C/UVM0FpJdxMJrcBMFgwLLQCIbAVnhHP34i6ppDRgxW/MfTeiCaaG6fnS70iv6mC
oh2N7FoZSKDtTrFtlR5TqFiK5v/W1CgNJVuglkFB0ceFpjyBpp/8AT0FGS887xCz
IYSTqm4Q/79vaZXI1Y2oog257cgdwsVqgPrnK5CuSFhTnAcJMCekiFelHq8Yhyuk
Rw7j/B3KO3AOaxmR75c6SZdeZ+VHgUMRC/RKe3fay0sm3Zea2kAIPXA6Zn+r/cxb
8M94V59qBz+f8XmpXRTK1UR3s3EbwFIuNyuDIkeorMtpSKtvqJXmZxGDwNIfXr2F
/voo++MKjzdtdxdW/D/5Tc9DC0Pyb4HLi0EYj2QCzA03njmfLDF1w73NfzMec+GD
R1zAd3FEbiJQx8Hin0PSPjYXpfMnkjkGAEcE9N9Ralg4ewNWAxfOFsAhHKTZNssL
pitTAvHR/+dXtvkX7FUi2l/6fqn8nJUrg/xRazPPp3scRbpuk8m6P4MNr3/lsaHk
HTQ/hYwDdecWLvKXjw5y9yIr3yhLmPPcloTVIIFFjsM0t8b+d9E=
=p6Xp
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv"
* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
power: supply: Introduce Qualcomm PMIC GLINK power supply
soc: apple: rtkit: Do not copy the reg state structure to the stack
soc: sunxi: SUN20I_PPU should depend on PM
memory: renesas-rpc-if: Remove redundant division of dummy
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
...
Fix the following compilation error when CONFIG_PM is set to 'n':
drivers/ufs/host/ufs-mediatek.c: In function `ufs_mtk_runtime_suspend`:
drivers/ufs/host/ufs-mediatek.c:1623:8: error: implicit declaration of
function `ufshcd_runtime_suspend`; did you mean `ufs_mtk_runtime_suspend`?
[-Werror=implicit-function-declaration]
1623 | ret = ufshcd_runtime_suspend(dev);
| ^~~~~~~~~~~~~~~~~~~~~~
| ufs_mtk_runtime_suspend
drivers/ufs/host/ufs-mediatek.c: In function `ufs_mtk_runtime_resume`:
drivers/ufs/host/ufs-mediatek.c:1638:9: error: implicit declaration of function
`ufshcd_runtime_resume`; did you mean `ufs_mtk_runtime_resume`?
[-Werror=implicit-function-declaration]
1638 | return ufshcd_runtime_resume(dev);
| ^~~~~~~~~~~~~~~~~~~~~
| ufs_mtk_runtime_resume
At top level:
drivers/ufs/host/ufs-mediatek.c:1632:12: error: `ufs_mtk_runtime_resume`
defined but not used [-Werror=unused-function]
1632 | static int ufs_mtk_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~
drivers/ufs/host/ufs-mediatek.c:1618:12: error: `ufs_mtk_runtime_suspend`
defined but not used [-Werror=unused-function]
1618 | static int ufs_mtk_runtime_suspend(struct device *dev)
Link: https://lore.kernel.org/r/20230220142431.54589-1-frank.li@vivo.com
Reported-by: k2ci <kernel-bot@kylinos.cn>
Reported-by: Shida Zhang <zhangshida@kylinos.cn>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The TC G210 driver only supports devices declared in the device tree.
Hence make this driver dependent on CONFIG_OF. This patch fixes the
following compiler error:
drivers/ufs/host/tc-dwc-g210-pltfrm.c:36:34: error: ‘tc_dwc_g210_pltfm_match’ defined but not used [-Werror=unused-const-variable=]
36 | static const struct of_device_id tc_dwc_g210_pltfm_match[] = {
|
Link: https://lore.kernel.org/r/20230209184914.2762172-1-bvanassche@acm.org
Cc: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move include/linux/qcom_scm.h to include/linux/firmware/qcom/qcom_scm.h.
This removes 1 of a few remaining Qualcomm-specific headers into a more
approciate subdirectory under include/.
Suggested-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Reviewed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Acked-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230203210956.3580811-1-quic_eberman@quicinc.com
Add freeze, thaw, and restore callbacks for hibernate and restore
functionality.
Link: https://lore.kernel.org/r/20230202161045.3956-2-quic_ahari@quicinc.com
Signed-off-by: Anjana Hari <quic_ahari@quicinc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On SM8550, depending on the Qunipro, we can run with G5 or G4. For now,
when the major version is 5 or above, we go with G5. Therefore, we need to
specifically tell UFS HC that.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The newly added MSI support is mostly hidden inside of an #ifdef,
except for one line that now causes a build failure when MSI
is disabled:
drivers/ufs/host/ufs-qcom.c: In function 'ufs_qcom_remove':
drivers/ufs/host/ufs-qcom.c:1698:9: error: implicit declaration of function 'platform_msi_domain_free_irqs' [-Werror=i]
1698 | platform_msi_domain_free_irqs(hba->dev);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Above that, the symbol that guards the other call was recently removed, so
that is all dead code at the moment.
Remove the incorrect #ifdef and instead of a Kconfig dependency to only
allow building the driver when CONFIG_GENERIC_MSI_IRQ is enabled. This
symbol is always present when PCI_MSI or ARM_GIC_V3_ITS are enabled, both
of which should be present on kernels that can run on Qualcomm SoCs.
The 'select RESET_CONTROLLER' in combination with this dependency
unfortunately causes a dependency loop and this is a user-visible symbol,
so it's better to change both to 'depends on'.
Link: https://lore.kernel.org/r/20230126211831.2274211-1-arnd@kernel.org
Fixes: 519b6274a7 ("scsi: ufs: qcom: Add MCQ ESI config vendor specific ops")
Fixes: 13e7accb81 ("genirq: Get rid of GENERIC_MSI_IRQ_DOMAIN")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prepare for enabling DMA clustering and also for supporting PAGE_SIZE !=
4096 by declaring explicitly that the maximum segment size is 4096 bytes
for Exynos UFS host controllers. Add this code in
exynos_ufs_hce_enable_notify() such that it happens after scsi_host_alloc()
and before __scsi_init_queue() is called by the LUN scanning code.
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The Exynos UFS controller only supports scatter/gather list elements that
are aligned on a 4 KiB boundary. Fix DMA alignment in case PAGE_SIZE !=
4096. Rename UFSHCD_QUIRK_ALIGN_SG_WITH_PAGE_SIZE into
UFSHCD_QUIRK_4KB_DMA_ALIGNMENT.
Cc: Kiwoong Kim <kwmad.kim@samsung.com>
Fixes: 2b2bfc8aa5 ("scsi: ufs: Introduce a quirk to allow only page-aligned sg entries")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add MCQ ESI config vendor specific ops.
Co-developed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for completing requests from Completion Queue. Some host
controllers support vendor specific registers that provide a bitmap of all
CQs which have at least one completed CQE. Add this support. The MCQ
specification doesn't provide the Task Tag or its equivalent in the
Completion Queue Entry. So use an indirect method to find the Task Tag
from the Completion Queue Entry.
Co-developed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Runtime and operation registers are defined per Submission and Completion
queue. The location of these registers is not defined in the spec; meaning
the offsets and stride may vary for different HC vendors. Establish the
stride, base address, and doorbell address offsets from vendor host driver
and program it.
Co-developed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFS device defines the supported queuedepth by bqueuedepth which has a
max value of 256. The HC defines MAC (Max Active Commands) that defines
the max number of commands that in flight to the UFS device. Calculate and
configure the nutrs based on both these values.
Co-developed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Define the MCQ resources and add support to ioremap the resource regions.
Co-developed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> says:
This series adds HS-G4 support to the Qcom UFS driver and PHY driver.
The newer Qcom platforms support configuring the UFS controller and
PHY in dual gears (i.e., controller/PHY can be configured to run in
two gear speeds). This is accomplished by adding two different PHY
init sequences to the PHY driver and the UFS driver requesting the one
that's required based on the platform configuration.
Initially the ufs-qcom driver will use the default gear G2 for
enumerating the UFS device. Afer enumeration, the max gear supported
by both the controller and device would be found out and that will be
used thereafter. But for using the max gear after enumeration, the
ufs-qcom driver requires the UFS device to be reinitialized. For this
purpose, a separate quirk has been introduced in the UFS core along
with a callback and those will be used by the ufs-qcom driver.
This series has been tested on following platforms:
* Qcom RB5 development platform powered by SM8250 SoC
* SM8450 based dev board
* Qdrive3/sa8540p-ride board based on SC8280XP (derivative)
Link: https://lore.kernel.org/r/20221222141001.54849-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Starting from Qcom UFS version 4.0, vendor specific REG_UFS_PARAM0 register
can be used to determine the maximum gear supported by the controller.
Suggested-by: Can Guo <quic_cang@quicinc.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Starting from Qualcomm UFS version 4, the UFS device needs to be
reinitialized after switching to maximum gear by the UFS core. Hence, add
support for it by enabling the UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH
quirk, implementing reinit_notify() callback and using the agreed gear
speed for setting the PHY mode.
Suggested-by: Can Guo <quic_cang@quicinc.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the preparation of adding support for new gears, move the logic that
finds the gear for each platform to a new function. This helps with code
readability and also allows the logic to be used in other places of the
driver in future.
While at it, make it clear that this driver only supports symmetric gear
setting (hs_tx_gear == hs_rx_gear).
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On newer UFS revisions, the register at offset 0xD0 is called,
REG_UFS_PARAM0. Since the existing register, RETRY_TIMER_REG is not used
anywhere, it is safe to use the new name.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make use of dev_err_probe() for printing the probe error.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use bitfield macros where appropriate to simplify the driver.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the reset assert and deassert callbacks, the supplied "id" is not used
at all and only the HBA reset is performed all the time. So there is no
reason to use a WARN_ON() on the "id".
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A goto statement in an error path is useful if the function needs to do
cleanup other than returning the error code. But in this driver, goto
statements are used for just returning the error code in many places. This
really makes it hard to read the code.
Get rid of those goto statements and just return the error code directly.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add driver code for Unisoc UFS host controller, along with UFS
initialization.
Signed-off-by: Zhe Wang <zhe.wang1@unisoc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche <bvanassche@acm.org> says:
The patches in this series are a first step towards integrating
support in the upstream kernel for the UFS controller in the Pixel 6
and 7.
[mkp: resolve conflict with RPMB series]
Link: https://lore.kernel.org/r/20221208234358.252031-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify the UFSHCD core to allow 'struct ufshcd_sg_entry' to be
variable-length. The default is the standard length, but variants can
override ufs_hba::sg_entry_size with a larger value if there are
vendor-specific fields following the standard ones.
This is needed to support inline encryption with ufs-exynos (FMP).
Cc: Eric Biggers <ebiggers@google.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
[ bvanassche: edited commit message and introduced CONFIG_SCSI_UFS_VARIABLE_SG_ENTRY_SIZE ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
dev_err() statements are better to use than pr_err(), so switch to those.
In a similar vein, the check on the dev_req_params pointer here is not
needed, the two places this function is called never pass in a NULL
pointer, so instead of using dev_err() there just remove it.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This bitmask is unconditionally set in the current driver, so all
conditionals using it can be considered bit rot.
Let's take the current default conditional path everywhere and remove
dbg_print_en from the driver.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current implementation has abstractions that don't give any benefits.
The print_fn callback (and its only callback implementation,
ufs_qcom_dump_regs_wrapper()) was only used by
ufs_qcom_print_hw_debug_reg_all() and just multiplies len by 4 before
calling ufshcd_dump_regs().
ufs_qcom_print_hw_debug_reg_all() is only called by
ufs_qcom_dump_dbg_regs().
There's no real gain in those abstractions, so let's just do the work
directly in ufs_qcom_dump_dbg_regs() (the dbg_register_dump callback).
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code path is only called through one function, and the HBA struct is
already accessed in ufshcd_vops_dbg_register_dump() prior to calling so
there is no way for it to be NULL.
Likewise, the print_fn callback is always supplied within this driver and
is always provided.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (target, ufs, smartpqi, lpfc). There are
some core changes, mostly around reworking some of our user context
assumptions in device put and moving some code around. The remaining
updates are bug fixes and minor changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCY5jjrSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishR9iAPwN++uF
BNlCD36duS8LslKQMPAmFxWt3d/4RWAHsXj2WQEAtu9q8K9PSe1ueb4y+rAEG4oj
2AUQhR3v9ciWBBKlDog=
=JYJC
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (target, ufs, smartpqi, lpfc).
There are some core changes, mostly around reworking some of our user
context assumptions in device put and moving some code around.
The remaining updates are bug fixes and minor changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (138 commits)
scsi: sg: Fix get_user() in call sg_scsi_ioctl()
scsi: megaraid_sas: Fix some spelling mistakes in comment
scsi: core: Use SCSI_SCAN_INITIAL in do_scsi_scan_host()
scsi: core: Use SCSI_SCAN_RESCAN in __scsi_add_device()
scsi: ufs: ufs-mediatek: Remove unnecessary return code
scsi: ufs: core: Fix the polling implementation
scsi: libsas: Do not export sas_ata_wait_after_reset()
scsi: hisi_sas: Fix SATA devices missing issue during I_T nexus reset
scsi: libsas: Add smp_ata_check_ready_type()
scsi: Revert "scsi: hisi_sas: Don't send bcast events from HW during nexus HA reset"
scsi: Revert "scsi: hisi_sas: Drain bcast events in hisi_sas_rescan_topology()"
scsi: ufs: ufs-mediatek: Modify the return value
scsi: ufs: ufs-mediatek: Remove unneeded code
scsi: device_handler: alua: Call scsi_device_put() from non-atomic context
scsi: device_handler: alua: Revert "Move a scsi_device_put() call out of alua_check_vpd()"
scsi: snic: Fix possible UAF in snic_tgt_create()
scsi: qla2xxx: Initialize vha->unknown_atio_[list, work] for NPIV hosts
scsi: qla2xxx: Remove duplicate of vha->iocb_work initialization
scsi: fcoe: Fix transport not deattached when fcoe_if_init() fails
scsi: sd: Use 16-byte SYNCHRONIZE CACHE on ZBC devices
...
Modify to remove unnecessary 'return 0' code.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20221121003338.11034-1-cw9316.lee@samsung.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Be consistent with the rest of driver wrt. functions returning bool.
91: return !!(host->caps & UFS_MTK_CAP_BOOST_CRYPT_ENGINE);
98: return !!(host->caps & UFS_MTK_CAP_VA09_PWR_CTRL);
105: return !!(host->caps & UFS_MTK_CAP_BROKEN_VCC);
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20221118045242.2770-1-cw9316.lee@samsung.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove unnecessary if/goto code.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20221118044136.921-1-cw9316.lee@samsung.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (qla2xxx, lpfc, ufs, hisi_sas, mpi3mr,
mpt3sas, target); the biggest change (from my biased viewpoint) being
that the mpi3mr now attached to the SAS transport class, making it the
first fusion type device to do so. Beyond the usual bug fixing and
security class reworks, there aren't a huge number of core changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCY0B74yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishW2NAP9CPp2R
7NRmSyxcyVYvtCNUW3WxXh65Gn+KgArmg8XucgEAhUBX1fSjOzpERWEU+UaXitbE
Rb+FbjxSc5YxR+nJ/Qc=
=0Wlp
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (qla2xxx, lpfc, ufs, hisi_sas, mpi3mr,
mpt3sas, target). The biggest change (from my biased viewpoint) being
that the mpi3mr now attached to the SAS transport class, making it the
first fusion type device to do so.
Beyond the usual bug fixing and security class reworks, there aren't a
huge number of core changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername()
scsi: mpi3mr: Remove unnecessary cast
scsi: stex: Properly zero out the passthrough command structure
scsi: mpi3mr: Update driver version to 8.2.0.3.0
scsi: mpi3mr: Fix scheduling while atomic type bug
scsi: mpi3mr: Scan the devices during resume time
scsi: mpi3mr: Free enclosure objects during driver unload
scsi: mpi3mr: Handle 0xF003 Fault Code
scsi: mpi3mr: Graceful handling of surprise removal of PCIe HBA
scsi: mpi3mr: Schedule IRQ kthreads only on non-RT kernels
scsi: mpi3mr: Support new power management framework
scsi: mpi3mr: Update mpi3 header files
scsi: mpt3sas: Revert "scsi: mpt3sas: Fix ioc->base_readl() use"
scsi: mpt3sas: Revert "scsi: mpt3sas: Fix writel() use"
scsi: wd33c93: Remove dead code related to the long-gone config WD33C93_PIO
scsi: core: Add I/O timeout count for SCSI device
scsi: qedf: Populate sysfs attributes for vport
scsi: pm8001: Replace one-element array with flexible-array member
scsi: 3w-xxxx: Replace one-element array with flexible-array member
scsi: hptiop: Replace one-element array with flexible-array member in struct hpt_iop_request_ioctl_command()
...
devm_ioremap_resource() already prints an error message. Remove the
redundant dev_err() call.
Link: https://lore.kernel.org/r/20220923101217.18345-1-shangxiaojing@huawei.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mediatek UFS does not want to toggle write booster during clock scaling.
Permit host driver to disable wb toggling during clock scaling.
Introduce a flag UFSHCD_CAP_WB_WITH_CLK_SCALING to decouple WB and clock
scaling. UFSHCD_CAP_WB_WITH_CLK_SCALING is only valid when
UFSHCD_CAP_CLK_SCALING is set. Just like UFSHCD_CAP_HIBERN8_WITH_CLK_GATING
is valid only when UFSHCD_CAP_CLK_GATING set.
Set UFSHCD_CAP_WB_WITH_CLK_SCALING for qcom to compatible legacy design at
the same time.
Link: https://lore.kernel.org/r/20220804025422.18803-1-peter.wang@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide clk-scaling feature in MediaTek UFS platforms.
MediaTek platform supports clk-scaling by switching parent clock mux of
UFSHCI main clocks: ufs_sel.
The driver needs to prevent changing the rate of ufs_sel because its parent
PLL clock may be shared between multiple IPs. In order to achieve this
goal, the maximum and minimum clock rates of ufs_sel defined in dts should
match the rate of "ufs_sel_max_src" and "ufs_sel_min_src" respectively.
Link: https://lore.kernel.org/r/20220802235437.4547-6-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If clk-scaling is enabled, performance scaling can be bound to the decision
of clk-scaling to avoid unnecessary boosting.
In addition, fix missing initialization of pm-qos request.
Link: https://lore.kernel.org/r/20220802235437.4547-5-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dump more proprietary UFSHCI status registers for easier issue breakdown.
Link: https://lore.kernel.org/r/20220802235437.4547-4-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove redundant #include of header file <linux/sched/clock.h>.
Link: https://lore.kernel.org/r/20220802235437.4547-2-stanley.chu@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mostly small bug fixes and trivial updates. The major new core update
is a change to the way device, target and host reference counting is
done to try to make it more robust (this change has soaked for a while
to try to winkle out any bugs).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYveemSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisheaiAP9DPQ70
7hEdak6evXUwlWwlVBvEFAfZlzpHN+uNzUCvpgD+N61RSPhHV1hXu12sVMmjMNEb
pow+ee47Mc0t/OO68jA=
=1yQh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Mostly small bug fixes and trivial updates.
The major new core update is a change to the way device, target and
host reference counting is done to try to make it more robust (this
change has soaked for a while to try to winkle out any bugs)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: pm8001: Fix typo 'the the' in comment
scsi: megaraid_sas: Remove redundant variable cmd_type
scsi: FlashPoint: Remove redundant variable bm_int_st
scsi: zfcp: Fix missing auto port scan and thus missing target ports
scsi: core: Call blk_mq_free_tag_set() earlier
scsi: core: Simplify LLD module reference counting
scsi: core: Make sure that hosts outlive targets
scsi: core: Make sure that targets outlive devices
scsi: ufs: ufs-pci: Correct check for RESET DSM
scsi: target: core: De-RCU of se_lun and se_lun acl
scsi: target: core: Fix race during ACL removal
scsi: ufs: core: Correct ufshcd_shutdown() flow
scsi: ufs: core: Increase the maximum data buffer size
scsi: lpfc: Check the return value of alloc_workqueue()
struct fsd_ufs_drvs is not used outside this file, so make it static. This
fixes sparse warning:
drivers/ufs/host/ufs-exynos.c:1721:28: sparse: sparse:
symbol 'fsd_ufs_drvs' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20220811161053.54081-1-alim.akhtar@samsung.com
Fixes: 216f74e805 ("scsi: ufs: host: ufs-exynos: Add support for FSD UFS HCI")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (ufs, qla2xx, target, lpfc, smartpqi,
mpi3mr). The main driver change that might cause issues on down the
road is the conversion of some of our oldest surviving drivers to the
DMA API (should only affect m68k). The only major core change is the
rework of async resume; the rest are either completely trivial or for
updating deprecated APIs.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYuvakyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfvOAP4m0N6b
e3JwoBtB1c0JMKv6G4gka8suEG8p5f4khDu8wwD+LfGUCzG49Y5Ts7rByXfEiGgO
krSdwsAZiV6yKg/HuPw=
=Ak9L
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, qla2xx, target, lpfc, smartpqi,
mpi3mr).
The main driver change that might cause issues on down the road is the
conversion of some of our oldest surviving drivers to the DMA API
(should only affect m68k).
The only major core change is the rework of async resume; the rest are
either completely trivial or for updating deprecated APIs"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (195 commits)
scsi: target: Remove XDWRITEREAD emulated support
scsi: megaraid: Remove the static variable initialisation
scsi: ch: Do not initialise statics to 0
scsi: ufs: core: Fix spelling mistake "Cannnot" -> "Cannot"
scsi: target: iscsi: Do not require target authentication
scsi: target: iscsi: Allow AuthMethod=None
scsi: target: iscsi: Support base64 in CHAP
scsi: target: iscsi: Add support for extended CDB AHS
scsi: ufs: dt-bindings: Add SC8280XP binding
scsi: target: iscsi: Fix clang -Wformat warnings
scsi: ufs: core: Read device property for ref clock
scsi: libsas: Resume SAS host for phy reset or enable via sysfs
scsi: hisi_sas: Modify v3 HW SATA completion error processing
scsi: hisi_sas: Relocate DMA unmap of SMP task
scsi: hisi_sas: Remove unnecessary variable to hold DMA map elements
scsi: hisi_sas: Call hisi_sas_slave_configure() from slave_configure_v3_hw()
scsi: mpi3mr: Delete a stray tab
scsi: mpi3mr: Unlock on error path
scsi: mpi3mr: Reduce VD queue depth on detecting throttling
scsi: mpi3mr: Resource Based Metering
...
dsm_fns is a bitmap, and it is 0-indexed according to the check in
__intel_dsm function. But common initialization was checking it as if it
was 1-indexed. This patch corrects the discrepancy. This change won't break
any existing calls to the function, since before the change both bits 0 and
1 were checked and needed to be set.
Link: https://lore.kernel.org/r/20220728111748.v3.1.I22460c4f4a9ccf2c96c3f9bb392b409926d80b2f@changeid
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Daniil Lunev <dlunev@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ufshcd_populate_vreg(), we should hold the reference returned by
of_parse_phandle() and then use it to call of_node_put() for refcount
balance.
Link: https://lore.kernel.org/r/20220719071529.1081166-1-windhl@126.com
Fixes: aa49761309 ("ufs: Add regulator enable support")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since commit 1599069a62 ("phy: core: Warn when phy_power_on is called
before phy_init"), the following warning has been reported:
phy_power_on was called before phy_init
To address this, we need to remove phy_power_on from exynos_ufs_phy_init()
and move it after phy_init. phy_power_off and phy_exit are also necessary
in exynos_ufs_remove().
Link: https://lore.kernel.org/r/20220706020255.151177-4-chanho61.park@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Checks information about tx_lanes, but is not used.
Since commit 1e1e465c6d ("scsi/ufs: qcom: Remove ufs_qcom_phy_*() calls
from host"), tx_lanes is deprecated.
As a result, ufs_qcom_link_startup_notify -> POST_CHANGE action does
nothing. If it is not going to be updated, it can be removed.
Link: https://lore.kernel.org/r/20220627235545.16943-1-cw9316.lee@samsung.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NULL pointer access issue was found for the regulator released
by ufs_mtk_vreg_fix_vccq(). Simply fix this issue by clearing
the released vreg pointer in ufs_hba struct.
Link: https://lore.kernel.org/r/20220623035052.18802-9-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Alice Chao <alice.chao@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add pm-qos request to support performance boosting in MediaTek UFS
platforms.
At the same time, adjust the order of function calls to be symmetric during
the low-power control flow.
Link: https://lore.kernel.org/r/20220623035052.18802-8-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add interfaces for controlling the host power to optimize the power
consumption in MediaTek UFS platforms.
Link: https://lore.kernel.org/r/20220623035052.18802-7-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In MediaTek UFS platforms, UniPro will not return reset confirm if it is in
POWERDOWN state thus hang issue may happen while disabling UFSHCI. Simply
disable this feature before UniPro leaves POWERDOWN state.
Link: https://lore.kernel.org/r/20220623035052.18802-6-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add "PRE_CHANGE" and "POST_CHANGE" information for ref-clk control to
precisely configure the low-power state of the parent of ref-clk.
Link: https://lore.kernel.org/r/20220623035052.18802-5-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFSHCI hosts in MediaTek UFS platform need workaround to prevent host
hang issue by setting CLK_CG bit before host is enabled.
This operation shall have no side effect on those platforms which do not
support this bit.
Link: https://lore.kernel.org/r/20220623035052.18802-4-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MediaTek decides to always add delays before and after VCC is turned-off.
Link: https://lore.kernel.org/r/20220623035052.18802-3-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix build warnings:
1.
../drivers/ufs/host/ufs-mediatek.c:1375:5: error: no previous prototype for function 'ufs_mtk_system_suspend' [-Werror,-Wmissing-prototypes]
int ufs_mtk_system_suspend(struct device *dev)
^
../drivers/ufs/host/ufs-mediatek.c:1375:1: note: declare 'static' if the function is not intended to be used outside of this translation unit
int ufs_mtk_system_suspend(struct device *dev)
^
static
2.
../drivers/ufs/host/ufs-mediatek.c:702:50: error: format specifies type 'unsigned long' but the argument has type 'int' [-Werror,-Wformat]
snprintf(vcc_name, MAX_VCC_NAME, "vcc-ufs%lu", ver);
~~~ ^~~
%d
Link: https://lore.kernel.org/r/20220623035052.18802-2-stanley.chu@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For code safety, constify pointers to data which is not modified.
Link: https://lore.kernel.org/r/20220623102432.108059-3-krzysztof.kozlowski@linaro.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If CONFIG_PM_SLEEP is not set.
make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu-, will fail:
drivers/ufs/host/ufs-mediatek.c: In function ‘ufs_mtk_vreg_fix_vcc’:
drivers/ufs/host/ufs-mediatek.c:688:46: warning: format ‘%u’ expects argument of type ‘unsigned int’, but argument 4 has type ‘long unsigned int’ [-Wformat=]
snprintf(vcc_name, MAX_VCC_NAME, "vcc-opt%u", res.a1);
~^ ~~~~~~
%lu
drivers/ufs/host/ufs-mediatek.c: In function ‘ufs_mtk_system_suspend’:
drivers/ufs/host/ufs-mediatek.c:1371:8: error: implicit declaration of function ‘ufshcd_system_suspend’; did you mean ‘ufs_mtk_system_suspend’? [-Werror=implicit-function-declaration]
ret = ufshcd_system_suspend(dev);
^~~~~~~~~~~~~~~~~~~~~
ufs_mtk_system_suspend
drivers/ufs/host/ufs-mediatek.c: In function ‘ufs_mtk_system_resume’:
drivers/ufs/host/ufs-mediatek.c:1386:9: error: implicit declaration of function ‘ufshcd_system_resume’; did you mean ‘ufs_mtk_system_resume’? [-Werror=implicit-function-declaration]
return ufshcd_system_resume(dev);
^~~~~~~~~~~~~~~~~~~~
ufs_mtk_system_resume
cc1: some warnings being treated as errors
The declaration of func "ufshcd_system_suspend()" depends on
CONFIG_PM_SLEEP, so the function wrapper ufs_mtk_system_suspend() should
wrapped by CONFIG_PM_SLEEP too.
Link: https://lore.kernel.org/r/20220619115432.205504-1-renzhijie2@huawei.com
Fixes: 3fd23b8dfb ("scsi: ufs: ufs-mediatek: Fix the timing of configuring device regulators")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some MediaTek UFS platforms support different VCCQx power rails, for
example, both 1.2v and 1.8v VCCQx, in a single kernel image.
To optimize the system power consumption, provide a way to disable and
release the unused power rail during the device probing.
Link: https://lore.kernel.org/r/20220616053725.5681-12-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Support multiple VCC sources in MediaTek UFS platforms.
Two options are provided and distinguished by specific device tree
attributes as below examples,
[Option 1: By numbering]
mediatek,ufs-vcc-by-num;
vcc-opt1-supply = <&mt6373_vbuck4_ufs>;
vcc-opt2-supply = <&mt6363_vemc>;
[Option 2: By UFS version]
mediatek,ufs-vcc-by-ver;
vcc-ufs3-supply = <&mt6373_vbuck4_ufs>;
Link: https://lore.kernel.org/r/20220616053725.5681-11-stanley.chu@mediatek.com
Signed-off-by: Alice Chao <alice.chao@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export below regulator functions to allow vendors to
customize regulator configuration in their own platforms.
int ufshcd_populate_vreg(struct device *dev, const char *name,
struct ufs_vreg **out_vreg);
int ufshcd_get_vreg(struct device *dev, struct ufs_vreg *vreg);
Link: https://lore.kernel.org/r/20220616053725.5681-10-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide the facility to configure parents of VCCQx power rails as low-power
or full-power mode in MediaTek UFS platforms.
Link: https://lore.kernel.org/r/20220616053725.5681-9-stanley.chu@mediatek.com
Signed-off-by: Alice Chao <alice.chao@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide flexible number of parameters for UFS SMC calls to be used in a
subsequent commit.
Link: https://lore.kernel.org/r/20220616053725.5681-8-stanley.chu@mediatek.com
Signed-off-by: Alice Chao <alice.chao@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow VCCQ to enter low-power mode, and also remove the restriction of VCC
because VCCQ/VCCQ2 can be changed to low-power mode even if VCC stays on
while the device is not in active power mode.
Link: https://lore.kernel.org/r/20220616053725.5681-7-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Device regulatrs are allowed to enter low-power mode if neither device is
not in active mode, nor VCC does not keep on.
Fix this by adding conditions before LPM decision.
Link: https://lore.kernel.org/r/20220616053725.5681-6-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the LPM configurations of device regulators may not work since
VCC is not disabled yet while ufs_mtk_vreg_set_lpm() is executed.
Fix this by changing the timing of invoking ufs_mtk_vreg_set_lpm().
Link: https://lore.kernel.org/r/20220616053725.5681-5-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some MediaTek SoC chips need special flow for power mode change, especially
for chips supporting HS-G5.
Enable the workaround by setting the host-specific capability.
Link: https://lore.kernel.org/r/20220616053725.5681-4-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: CC Chou <cc.chou@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Dennis Yu <tun-yu.yu@mediatek.com>
Signed-off-by: Peter Wang <peter.want@medaitek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS core already uses RX_MIN_ACTIVATETIME_CAPABILITY macro, let's use the
same in driver as well instead of having a different macro name for the
same offset.
Link: https://lore.kernel.org/r/20220615121204.16642-2-alim.akhtar@samsung.com
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove #defines as those are not used anywhere in the driver file.
Link: https://lore.kernel.org/r/20220615121204.16642-1-alim.akhtar@samsung.com
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Constify the drv data because it should not be modified (used by multiple
devices).
Link: https://lore.kernel.org/r/20220613101429.114449-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adds support of UFS HCI which is found in Tesla Full Self-Driving (FSD)
SoC.
Link: https://lore.kernel.org/r/20220610104119.66401-7-alim.akhtar@samsung.com
Co-developed-by: Bharat Uppal <bharat.uppal@samsung.com>
Signed-off-by: Bharat Uppal <bharat.uppal@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bit[3] of HCI_CLKSTOP_CTRL register is for enabling/disabling MPHY APB
clock. Lets add it to CLK_STOP_MASK, so that the same can be controlled
during clock masking/unmasking.
Link: https://lore.kernel.org/r/20220610104119.66401-6-alim.akhtar@samsung.com
Tested-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Split the drivers/scsi/ufs directory into 'core' and 'host' directories
under the drivers/ufs/ directory. Move shared header files into the
include/ufs/ directory. This separation makes it clear which header files
UFS drivers are allowed to include (include/ufs/*.h) and which header files
UFS drivers are not allowed to include (drivers/ufs/core/*.h).
Update the MAINTAINERS file. Add myself as a UFS reviewer.
Link: https://lore.kernel.org/r/20220511212552.655341-1-bvanassche@acm.org
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Keoseong Park <keosung.park@samsung.com>
Tested-by: Bean Huo <beanhuo@micron.com>
Tested-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
