After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/ufs to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241119182856.55743-2-u.kleine-koenig@baylibre.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some early UFSHCI 4.0 controllers support the UFSHCI 3.0 register set.
The UFSHCD_QUIRK_BROKEN_LSDBS_CAP quirk must be set for these controllers.
Commit b92e5937e3 ("scsi: ufs: core: Move code out of an if-statement")
changed the behavior for these controllers from working fine into
"ufshcd_add_scsi_host: failed to initialize (legacy doorbell mode not
supported)". Fix this by setting the "broken LSDBS" quirk for the
SM8650 development board.
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Closes: https://lore.kernel.org/linux-scsi/0c0bc528-fdc2-4106-bc99-f23ae377f6f5@linaro.org/
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Fixes: b92e5937e3 ("scsi: ufs: core: Move code out of an if-statement")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241106181011.4132974-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add fixup_dev_quirk vops in QCOM UFS platforms and provide an initial
vendor-specific device quirk table to add UFS device specific quirks which
are enabled only for specified UFS devices.
- Add DELAY_BEFORE_LPM quirk for Skhynix UFS devices to introduce a delay
before VCC is powered off in QCOM platforms.
- Add DELAY_AFTER_LPM quirk for Toshiba UFS devices to introduce a delay
after the VCC power rail is turned off in QCOM platforms.
- Move UFS_DEVICE_QUIRK_HOST_PA_TACTIVATE quirk from
ufs_qcom_apply_dev_quirks to ufs_qcom_dev_fixups.
Signed-off-by: Manish Pandey <quic_mapa@quicinc.com>
Link: https://lore.kernel.org/r/20240903131546.1141-1-quic_mapa@quicinc.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These are mostly minor updates. There are two drivers (lpfc and
mpi3mr) which missed the initial pull and a core change to retry a
start/stop unit which affect suspend/resume.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZvh4QiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQajAQDx561I
cgbPZjZkSOYp+qJowaphyySZ1SS8pfMlVAIiXQEAs4SqhIN8e9QWpgI0bA7X7xtB
UiOUsIHPHM+BFU6kbJQ=
=qjsp
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"These are mostly minor updates.
There are two drivers (lpfc and mpi3mr) which missed the initial
pull and a core change to retry a start/stop unit which affect
suspend/resume"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
scsi: lpfc: Update lpfc version to 14.4.0.5
scsi: lpfc: Support loopback tests with VMID enabled
scsi: lpfc: Revise TRACE_EVENT log flag severities from KERN_ERR to KERN_WARNING
scsi: lpfc: Ensure DA_ID handling completion before deleting an NPIV instance
scsi: lpfc: Fix kref imbalance on fabric ndlps from dev_loss_tmo handler
scsi: lpfc: Restrict support for 32 byte CDBs to specific HBAs
scsi: lpfc: Update phba link state conditional before sending CMF_SYNC_WQE
scsi: lpfc: Add ELS_RSP cmd to the list of WQEs to flush in lpfc_els_flush_cmd()
scsi: mpi3mr: Update driver version to 8.12.0.0.50
scsi: mpi3mr: Improve wait logic while controller transitions to READY state
scsi: mpi3mr: Update MPI Headers to revision 34
scsi: mpi3mr: Use firmware-provided timestamp update interval
scsi: mpi3mr: Enhance the Enable Controller retry logic
scsi: sd: Fix off-by-one error in sd_read_block_characteristics()
scsi: pm8001: Do not overwrite PCI queue mapping
scsi: scsi_debug: Remove a useless memset()
scsi: pmcraid: Convert comma to semicolon
scsi: sd: Retry START STOP UNIT commands
scsi: mpi3mr: A performance fix
scsi: ufs: qcom: Update MODE_MAX cfg_bw value
...
Commit 8db8f6ce55 ("scsi: ufs: qcom: Add missing interconnect bandwidth
values for Gear 5") updated the ufs_qcom_bw_table for Gear 5. However, it
missed updating the cfg_bw value for the max mode.
Hence update the cfg_bw value for the max mode for UFS 4.x devices.
Fixes: 8db8f6ce55 ("scsi: ufs: qcom: Add missing interconnect bandwidth values for Gear 5")
Cc: stable@vger.kernel.org
Signed-off-by: Manish Pandey <quic_mapa@quicinc.com>
Link: https://lore.kernel.org/r/20240903063709.4335-1-quic_mapa@quicinc.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SM8550 SoC has the UFSHCI 4.0 compliant UFS controller and only supports
legacy single doorbell mode without MCQ. But due to a hardware bug, it
reports 1 in the 'Legacy Queue & Single Doorbell Support (LSDBS)' field of
the Controller Capabilities register. This field is supposed to read as 0
if legacy single doorbell mode is supported and 1 otherwise.
Starting with commit 0c60eb0cc3 ("scsi: ufs: core: Check LSDBS cap when
!mcq"), ufshcd driver is now relying on the LSDBS field to decide when to
use the legacy doorbell mode if MCQ is not supported. And this ends up
breaking UFS on SM8550:
ufshcd-qcom 1d84000.ufs: ufshcd_init: failed to initialize (legacy doorbell mode not supported)
ufshcd-qcom 1d84000.ufs: error -EINVAL: Initialization failed with error -22
So use the UFSHCD_QUIRK_BROKEN_LSDBS_CAP quirk for SM8550 SoC so that the
ufshcd driver could use legacy doorbell mode correctly.
Fixes: 0c60eb0cc3 ("scsi: ufs: core: Check LSDBS cap when !mcq")
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240816-ufs-bug-fix-v3-2-e6fe0e18e2a3@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable suspending clk scaling on no request for Qualcomm SoC.
Signed-off-by: Ram Prakash Gupta <quic_rampraka@quicinc.com>
Link: https://lore.kernel.org/r/20240627083756.25340-3-quic_rampraka@quicinc.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With ARCH=arm64, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/ufs/host/ufs-qcom.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240625-md-drivers-ufs-host-v2-1-59a56974b05a@quicinc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (ufs, lpfc, qla2xxx, mpi3mr, libsas).
The major update (which causes a conflict with block, see below) is
Christoph removing the queue limits and their associated block
helpers. The remaining patches are assorted minor fixes and
deprecated function updates plus a bit of constification.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZkOnWyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYe7AP93XRN/
xnccJbSTTUL4FFGobq2CYXv58Na+FM/b/+/kEAD+PNi0LmHDdDTOaFUblMd9l4lj
mpvYLRvJ6ifnHX6WXAg=
=PVnL
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, qla2xxx, mpi3mr, libsas).
The major update (which causes a conflict with block, see below) is
Christoph removing the queue limits and their associated block
helpers.
The remaining patches are assorted minor fixes and deprecated function
updates plus a bit of constification"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
scsi: mpi3mr: Sanitise num_phys
scsi: lpfc: Copyright updates for 14.4.0.2 patches
scsi: lpfc: Update lpfc version to 14.4.0.2
scsi: lpfc: Add support for 32 byte CDBs
scsi: lpfc: Change lpfc_hba hba_flag member into a bitmask
scsi: lpfc: Introduce rrq_list_lock to protect active_rrq_list
scsi: lpfc: Clear deferred RSCN processing flag when driver is unloading
scsi: lpfc: Update logging of protection type for T10 DIF I/O
scsi: lpfc: Change default logging level for unsolicited CT MIB commands
scsi: target: Remove unused list 'device_list'
scsi: iscsi: Remove unused list 'connlist_err'
scsi: ufs: exynos: Add support for Tensor gs101 SoC
scsi: ufs: exynos: Add some pa_dbg_ register offsets into drvdata
scsi: ufs: exynos: Allow max frequencies up to 267Mhz
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_TIMER_TICK_SELECT option
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_UFSPR_SECURE option
scsi: ufs: dt-bindings: exynos: Add gs101 compatible
scsi: qla2xxx: Fix debugfs output for fw_resource_count
scsi: qedf: Ensure the copied buf is NUL terminated
scsi: bfa: Ensure the copied buf is NUL terminated
...
UFS spec version 2.1 was published more than 10 years ago. It is
vanishingly unlikely that even there are out there platforms that uses
earlier host controllers, let alone that those ancient platforms will ever
run a V6.10 kernel. To be extra cautious, leave out removal of UFSHCI 2.0
support from this patch, and just remove support of host controllers prior
to UFS2.0.
This patch removes some legacy tuning calls that no longer apply.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240410183720.908-2-avri.altman@wdc.com
Acked-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Let's add the checks to warn the user if the ICC scaling is not supported
for the gear/lane values and also fallback to the max value if that's the
case.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240403-ufs-icc-fix-v2-2-958412a5eb45@linaro.org
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These entries are necessary to scale the interconnect bandwidth while
operating in Gear 5.
Cc: Amit Pundir <amit.pundir@linaro.org>
Fixes: 03ce80a1bb ("scsi: ufs: qcom: Add support for scaling interconnects")
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240403-ufs-icc-fix-v2-1-958412a5eb45@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Andrew Halaney <ahalaney@redhat.com> says:
Please review with care as I'm not all that confident in this subject.
UFS has a lot of mb() variants used, most with comments saying "ensure
this takes effect before continuing". mb()'s aren't really the way to
guarantee that, a read back is the best method.
Some of these though I think could go a step further and remove the
mb() variant without a read back. As far as I can tell there's no real
reason to ensure it takes effect in most cases (there's no delay() or
anything afterwards, and eventually another readl()/writel() happens
which is by definition ordered). Some of the patches in this series do
that if I was confident it was safe (or a reviewer pointed out prior
that they thought it was safe to do so).
Thanks in advance for the help,
Andrew
Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-0-181252004586@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the CGC enable bit is written and then an mb() is used to ensure
that completes before continuing.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
https://youtu.be/i6DayghhA8Q?si=MiyxB5cKJXSaoc01&t=1678
Let's do that to ensure the bit hits the device. Because the mb()'s purpose
wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Fixes: 81c0fc51b7 ("ufs-qcom: add support for Qualcomm Technologies Inc platforms")
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-5-181252004586@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the QUNIPRO_SEL bit is written to and then an mb() is used to
ensure that completes before continuing.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
https://youtu.be/i6DayghhA8Q?si=MiyxB5cKJXSaoc01&t=1678
But, there's really no reason to even ensure completion before
continuing. The only requirement here is that this write is ordered to this
endpoint (which readl()/writel() guarantees already). For that reason the
mb() can be dropped altogether without anything forcing completion.
Fixes: f06fcc7155 ("scsi: ufs-qcom: add QUniPro hardware support and power optimizations")
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-4-181252004586@redhat.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the testbus configuration is written and completed with an mb().
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
https://youtu.be/i6DayghhA8Q?si=MiyxB5cKJXSaoc01&t=1678
But, there's really no reason to even ensure completion before
continuing. The only requirement here is that this write is ordered to this
endpoint (which readl()/writel() guarantees already). For that reason the
mb() can be dropped altogether without anything forcing completion.
Fixes: 9c46b86762 ("scsi: ufs-qcom: dump additional testbus registers")
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-3-181252004586@redhat.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently after writing to REG_UFS_SYS1CLK_1US a mb() is used to ensure
that write has gone through to the device.
mb() ensures that the write completes, but completion doesn't mean that it
isn't stored in a buffer somewhere. The recommendation for ensuring this
bit has taken effect on the device is to perform a read back to force it to
make it all the way to the device. This is documented in device-io.rst and
a talk by Will Deacon on this can be seen over here:
https://youtu.be/i6DayghhA8Q?si=MiyxB5cKJXSaoc01&t=1678
Let's do that to ensure the bit hits the device. Because the mb()'s purpose
wasn't to add extra ordering (on top of the ordering guaranteed by
writel()/readl()), it can safely be removed.
Fixes: f06fcc7155 ("scsi: ufs-qcom: add QUniPro hardware support and power optimizations")
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240329-ufs-reset-ensure-effect-before-delay-v5-2-181252004586@redhat.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Only a couple of driver updates this time (lpfc and mpt3sas) plus the
usual assorted minor fixes and updates. The major core update is a
set of patches moving retries out of the drivers and into the core.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZfWpoCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXRgAP9EJN6k
lA+f8he/ckzfJu000zv55uwKeZhI1ytgNnQUGwEAzv7Yetcqra18spuEnHRvxnW9
+lxUGh6revfrO/sc5Ho=
=ONSb
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Only a couple of driver updates this time (lpfc and mpt3sas) plus the
usual assorted minor fixes and updates. The major core update is a set
of patches moving retries out of the drivers and into the core"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (84 commits)
scsi: core: Constify the struct device_type usage
scsi: libfc: replace deprecated strncpy() with memcpy()
scsi: lpfc: Replace deprecated strncpy() with strscpy()
scsi: bfa: Fix function pointer type mismatch for state machines
scsi: bfa: Fix function pointer type mismatch for hcb_qe->cbfn
scsi: bfa: Remove additional unnecessary struct declarations
scsi: csiostor: Avoid function pointer casts
scsi: qla1280: Remove redundant assignment to variable 'mr'
scsi: core: Make scsi_bus_type const
scsi: core: Really include kunit tests with SCSI_LIB_KUNIT_TEST
scsi: target: tcm_loop: Make tcm_loop_lld_bus const
scsi: scsi_debug: Make pseudo_lld_bus const
scsi: iscsi: Make iscsi_flashnode_bus const
scsi: fcoe: Make fcoe_bus_type const
scsi: lpfc: Copyright updates for 14.4.0.0 patches
scsi: lpfc: Update lpfc version to 14.4.0.0
scsi: lpfc: Change lpfc_vport load_flag member into a bitmask
scsi: lpfc: Change lpfc_vport fc_flag member into a bitmask
scsi: lpfc: Protect vport fc_nodes list with an explicit spin lock
scsi: lpfc: Change nlp state statistic counters into atomic_t
...
The MSM8996 DT doesn't provide frequency limits for the core_clk_unipro
clock, which results in miscalculation of the cycles_in_1us value. Provide
the backwards-compatible default to support existing MSM8996 DT files.
Fixes: b4e13e1ae9 ("scsi: ufs: qcom: Add multiple frequency support for MAX_CORE_CLK_1US_CYCLES")
Cc: Nitin Rawat <quic_nitirawa@quicinc.com>
Cc: stable@vger.kernel.org # 6.7.x
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240218-msm8996-fix-ufs-v3-1-40aab49899a3@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch all the users of the platform MSI domain over to invoke the new
interfaces which branch to the original platform MSI functions when the
irqdomain associated to the caller device does not yet provide MSI parent
functionality.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240127161753.114685-7-apatel@ventanamicro.com
On sa8775p-ride, probing the HBA will go through the
UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH path although the power info is
the same during the second init.
The REINIT quirk only applies starting with controller v4. For these,
ufs_qcom_get_hs_gear() reads the highest supported gear when setting the
host_params. After the negotiation, if the host and device are on the same
gear, it is the highest gear supported between the two. Skip REINIT to save
some time.
Signed-off-by: Eric Chanudet <echanude@redhat.com>
Link: https://lore.kernel.org/r/20240123192854.1724905-4-echanude@redhat.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The comments that currently are within the hw_ver < 4 conditional are
misleading. They really apply to various branches of the conditionals there
and incorrectly state that the phy_gear value can increase.
Right now the logic is to:
- Default to max supported gear for phy_gear
- Set phy_gear to minimum value if version < 4 since those versions only
support one PHY init sequence (and therefore don't need reinit)
- Set phy_gear to the optimal value if the device version is already
populated in the controller registers on boot
Let's move some of the comment to outside the if statement and clean up the
bit left about switching to a higher gear on reinit. This way the comment
more accurately reflects the logic.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240123-ufs-reinit-comments-v1-1-ff2b3532d7fe@redhat.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Final round of fixes that came in too late to send in the first
request. It's 9 bug fixes and one version update (because of a bug
fix) and one set of PCI ID additions. There's one bug fix in the core
which is really a one liner (except that an additional sdev pointer
was added for convenience) and the rest are in drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZavlICYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSIpAP9Ynm64
sxlwxmaRv9uzf6+Nbadesve0UWCPHHYjIxtNBwD/SV6wgn/WdJqO1rONR8w3RknL
ZFShKw5QmiKXVDmDJTg=
=WSYQ
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Final round of fixes that came in too late to send in the first
request.
It's nine bug fixes and one version update (because of a bug fix) and
one set of PCI ID additions. There's one bug fix in the core which is
really a one liner (except that an additional sdev pointer was added
for convenience) and the rest are in drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: core: Add TMF to tmr_list handling
scsi: core: Kick the requeue list after inserting when flushing
scsi: fnic: unlock on error path in fnic_queuecommand()
scsi: fcoe: Fix unsigned comparison with zero in store_ctlr_mode()
scsi: mpi3mr: Fix mpi3mr_fw.c kernel-doc warnings
scsi: smartpqi: Bump driver version to 2.1.26-030
scsi: smartpqi: Fix logical volume rescan race condition
scsi: smartpqi: Add new controller PCI IDs
scsi: ufs: qcom: Remove unnecessary goto statement from ufs_qcom_config_esi()
scsi: ufs: core: Remove the ufshcd_hba_exit() call from ufshcd_async_scan()
scsi: ufs: core: Simplify power management during async scan
Updates to the usual drivers (ufs, mpi3mr, mpt3sas, lpfc, fnic,
hisi_sas, arcmsr, ) plus the usual assorted minor fixes and updates.
This time around there's only a single line update to the core, so
nothing major and barely anything minor.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZZ7roSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisha3lAQC5BAGM
7OKk39iOtsKdq8uxYAhYx871sNtwBp8+BSk1FgEAhy1hg7fgCnOvl7chbSNDR6p/
mW11fYi4j2UvxECT2tg=
=/tvT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, mpi3mr, mpt3sas, lpfc, fnic,
hisi_sas, arcmsr, ) plus the usual assorted minor fixes and updates.
This time around there's only a single line update to the core, so
nothing major and barely anything minor"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (135 commits)
scsi: ufs: core: Simplify ufshcd_auto_hibern8_update()
scsi: ufs: core: Rename ufshcd_auto_hibern8_enable() and make it static
scsi: ufs: qcom: Fix ESI vector mask
scsi: ufs: host: Fix kernel-doc warning
scsi: hisi_sas: Correct the number of global debugfs registers
scsi: hisi_sas: Rollback some operations if FLR failed
scsi: hisi_sas: Check before using pointer variables
scsi: hisi_sas: Replace with standard error code return value
scsi: hisi_sas: Set .phy_attached before notifing phyup event HISI_PHYE_PHY_UP_PM
scsi: ufs: core: Add sysfs node for UFS RTC update
scsi: ufs: core: Add UFS RTC support
scsi: ufs: core: Add ufshcd_is_ufs_dev_busy()
scsi: ufs: qcom: Remove unused definitions
scsi: ufs: qcom: Use ufshcd_rmwl() where applicable
scsi: ufs: qcom: Remove support for host controllers older than v2.0
scsi: ufs: qcom: Simplify ufs_qcom_{assert/deassert}_reset
scsi: ufs: qcom: Initialize cycles_in_1us variable in ufs_qcom_set_core_clk_ctrl()
scsi: ufs: qcom: Sort includes alphabetically
scsi: ufs: qcom: Remove unused ufs_qcom_hosts struct array
scsi: ufs: qcom: Use dev_err_probe() to simplify error handling of devm_gpiod_get_optional()
...
There is only one place where goto is used, and it is unnecessary to check
the ret value through 'goto out' because the ret value is already true.
Therefore, remove the goto statement and integrate the '!ret' condition
into the existing code.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20231219082740.27644-1-cw9316.lee@samsung.com
Reviewed-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit 031312dbc6 ("scsi: ufs: ufs-qcom: Remove unnecessary goto
statements") the error handling was accidentally changed, resulting in the
error of ufs_qcom_clk_scale_*() calls not being returned.
This is the case I checked:
ufs_qcom_clk_scale_notify ->
'ufs_qcom_clk_scale_up_/down_pre_change' error ->
return 0;
Make sure those errors are properly returned.
Fixes: 031312dbc6 ("scsi: ufs: ufs-qcom: Remove unnecessary goto statements")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20231215003812.29650-1-cw9316.lee@samsung.com
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While cleaning up the code to use ufshcd_rmwl() helper, the ESI vector mask
was changed incorrectly. Fix it and also define a proper macro for the
value together with FIELD_PREP().
Reported-by: Andrew Halaney <ahalaney@redhat.com>
Fixes: 0e9f4375db ("scsi: ufs: qcom: Use ufshcd_rmwl() where applicable")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231214125532.55109-1-manivannan.sadhasivam@linaro.org
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> says:
Hello,
This series has code some cleanups to the Qcom UFS driver. No
functional change. In this version, I've removed code supporting
legacy controllers ver < 2.0, as the respective platforms were never
supported in upstream.
Tested on: RB5 development board based on Qcom SM8250 SoC.
Link: https://lore.kernel.org/r/20231208065902.11006-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of using both ufshcd_readl() and ufshcd_writel() to read/modify/
write a register, let's make use of the existing helper.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-17-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The legacy platforms making use of host controllers older than version 2.0
are not supported in upstream. So there is no need to carry code to support
them.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-16-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case the "core_clk_unipro" clock is not provided, "cycles_in_1us"
variable will be used as uninitialized. So initialize it with 0.
Issue reported by Smatch tool:
drivers/ufs/host/ufs-qcom.c:1336 ufs_qcom_set_core_clk_ctrl() error: uninitialized symbol 'cycles_in_1us'.
drivers/ufs/host/ufs-qcom.c:1341 ufs_qcom_set_core_clk_ctrl() error: uninitialized symbol 'cycles_in_1us'.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-14-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufs_qcom_hosts array is assigned, but not used anywhere. So let's remove
it.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-12-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As done in other places, let's use dev_err_probe() to simplify the error
handling while acquiring the device reset gpio using
devm_gpiod_get_optional().
While at it, let's reword the error message to make it clear that the
failure is due to acquiring "device reset gpio".
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-11-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
devm_kzalloc() will itself print the error message on failure. So let's get
rid of the redundant error message in ufs_qcom_init().
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-10-manivannan.sadhasivam@linaro.org
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If ufs_qcom_power_up_sequence() fails, then it makes no sense to enable the
lane clocks and continue ufshcd_hba_enable(). So let's check the return
value of ufs_qcom_power_up_sequence().
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-9-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Even though core_reset is optional, a failure during assert/deassert should
be considered fatal, if core_reset is available. So fail
ufs_qcom_power_up_sequence() if an error happens during reset and also get
rid of the redundant warning as the ufs_qcom_host_reset() function itself
prints error messages.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-8-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of duplicating the enable/disable IRQ part, let's export the
helpers available in ufshcd driver and make use of them. This also fixes
the possible redundant IRQ disable before asserting reset (when IRQ was
already disabled).
Fixes: 4a791574a0 ("scsi: ufs: ufs-qcom: Disable interrupt in reset path")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-7-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
core_reset is optional, so there is no need to warn the user if it is not
available.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-6-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are many instances where the variable assignments are not needed.
Remove them.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-5-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return value should be -ENODEV indicating that the resource is not
provided in DT, not -ENOMEM. Fix it!
Fixes: c263b4ef73 ("scsi: ufs: core: mcq: Configure resource regions")
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-4-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the function returns -EINVAL if algorithm other than AES-256-XTS
is requested. But the correct error code is -EOPNOTSUPP. Fix it!
Cc: Abel Vesa <abel.vesa@linaro.org>
Fixes: 56541c7c44 ("scsi: ufs: ufs-qcom: Switch to the new ICE API")
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-3-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Lane clock handling can be simplified by using the clk_bulk APIs. So let's
make use of them. This also get's rid of the clock validation in the driver
as kernel should just rely on the firmware (DT/ACPI) to provide the clocks
required for proper functioning.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231208065902.11006-2-manivannan.sadhasivam@linaro.org
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Start from HW ver 5, a spare register in UFS host controller is added and
used to indicate the UFS device version. The spare register is populated by
bootloader for now, but in future it will be populated by HW automatically
during link startup with its best efforts in any boot stage prior to Linux.
During host driver init, read the spare register, if it is not populated
with a UFS device version, go ahead with the dual init mechanism. If a UFS
device version is in there, use the UFS device version together with host
controller's HW version to decide the proper PHY gear which should be used
to configure the UFS PHY without going through the second init.
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-9-git-send-email-quic_cang@quicinc.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ufs_qcom_power_up_sequence(), check return value of phy_set_mode_ext()
and stop proceeding if phy_set_mode_ext() fails.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-8-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since HW ver 4, max HS gear can be get from UFS host controller's register,
use the max HS gear as the initial PHY gear instead of UFS_HS_G2, so that
we don't need to update the hard code for newer targets in future.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-7-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Qcom UFS hosts, with HW ver 5, can only support up to HS-G5 Rate-A due to
HW limitations. If the HS-G5 PHY gear is used, update host_params->hs_rate
to Rate-A, so that the subsequent power mode changes shall stick to Rate-A.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-6-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During host driver init, the phy_gear is set to the minimum supported gear
(HS_G2). Then, during the first power mode change, the negotiated gear, say
HS-G4, is updated to the phy_gear variable so that in the second init the
updated phy_gear can be used to program the PHY.
But the current code only allows update the phy_gear to a higher value. If
one wants to start the first init with the maximum support gear, say HS-G4,
the phy_gear is not updated to HS-G3 if the device only supports HS-G3.
The original check added there is intend to make sure the phy_gear won't be
updated when gear is scaled down (during clock scaling). Update the check
so that one can start the first init with the maximum support gear without
breaking the original fix by checking the ufshcd_state, that is, allow
update to phy_gear only if power mode change is invoked from
ufshcd_probe_hba().
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-5-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Setup host power mode and its limitations during UFS host driver init to
avoid repetitive work during every power mode change.
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Co-developed-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-4-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ufs_qcom_pwr_change_notify(), host_params.hs_rate has been set to
PA_HS_MODE_B by ufshcd_init_host_param(), hence remove the duplicated line
of work. Meanwhile, removed the macro UFS_QCOM_LIMIT_HS_RATE as it is only
used here.
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-3-git-send-email-quic_cang@quicinc.com
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Structure ufs_dev_params is actually used in UFS host drivers to declare
host specific power mode parameters, like ufs_<vendor>_params or host_cap,
which makes the code not very straightforward to read. Rename the structure
ufs_dev_params to ufs_host_params and unify the declarations in all drivers
to host_params.
In addition, rename the two functions ufshcd_init_pwr_dev_param() and
ufshcd_get_pwr_dev_param() which work based on the ufs_host_params to
ufshcd_init_host_params() and ufshcd_negotiate_pwr_params() respectively to
avoid confusions.
This change does not change any functionalities or logic.
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1701520577-31163-2-git-send-email-quic_cang@quicinc.com
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "attr" pointer points to an offset into the "host" struct so it can't
be NULL. Delete the if statement and pull the code in a tab.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/fe3b8fcd-64a7-4887-bddd-32239a88a6a3@moroto.mountain
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To
improve here there is a quest to make the remove callback return void. In
the first step of this quest all drivers are converted to .remove_new()
which already returns void. Eventually after all drivers are converted,
.remove_new() is renamed to .remove().
All platform drivers below drivers/ufs/ unconditionally return zero in
their remove callback and so can be converted trivially to the variant
returning void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230917145722.1131557-1-u.kleine-koenig@pengutronix.de
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "hs_gear" variable is used to cache the gear setting for the PHY that
will be used during ufs_qcom_power_up_sequence(). But it creates ambiguity
with the gear setting used by the ufshcd driver.
So let's rename it to "phy_gear" to make it explicit that this variable
caches the gear setting for the PHY.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230908145329.154024-2-manivannan.sadhasivam@linaro.org
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Tested-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "hs_gear" variable is used to program the PHY settings (submode) during
ufs_qcom_power_up_sequence(). Currently, it is being updated every time the
agreed gear changes. Due to this, if the gear got downscaled before suspend
(runtime/system), then while resuming, the PHY settings for the lower gear
will be applied first and later when scaling to max gear with REINIT, the
PHY settings for the max gear will be applied.
This adds a latency while resuming and also really not needed as the PHY
gear settings are backwards compatible i.e., we can continue using the PHY
settings for max gear with lower gear speed.
So let's update the "hs_gear" variable _only_ when the agreed gear is
greater than the current one. This guarantees that the PHY settings will be
changed only during probe time and fatal error condition.
Due to this, UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH can now be skipped
when the PM operation is in progress.
Cc: stable@vger.kernel.org
Fixes: 96a7141da3 ("scsi: ufs: core: Add support for reinitializing the UFS device")
Reported-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230908145329.154024-1-manivannan.sadhasivam@linaro.org
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Tested-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SYS1CLK_1US represents the required number of system 1-clock cycles for one
microsecond. UFS Host Controller V4.0 and above mandates to write
SYS1CLK_1US_REG register and also these timer configuration needs to be
called from clk scaling pre ops as per HPG.
Refactor ufs_qcom_cfg_timers and add the below code support to align
with HPG.
a)Configure SYS1CLK_1US_REG for UFS V4 and above.
b)Introduce a new argument is_pre_scale_up for ufs_qcom_cfg_timers
to configure SYS1CLK_1US for max freq during prescale and link startup
condition.
c)Move ufs_qcom_cfg_timers from clk scaling post change ops
to clk scaling pre change ops.
Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20230905052400.13935-6-quic_nitirawa@quicinc.com
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently CORE_CLK_1US_CYCLES, PA_VS_CORE_CLK_40NS_CYCLES are configured
in clk scaling post change ops. This is not aligning to HPG.
Move this to clk scaling pre change ops to align completely with hardware
specification.
Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20230905052400.13935-5-quic_nitirawa@quicinc.com
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PA_VS_CORE_CLK_40NS_CYCLES attribute represents the required number of
Qunipro core clock for 40 nanoseconds. For UFS host controller V4 and above
PA_VS_CORE_CLK_40NS_CYCLES needs to be programmed as per frequency of
unipro core clk of UFS host controller.
Add Support to configure PA_VS_CORE_CLK_40NS_CYCLES for Controller V4 and
above to align with the hardware specification and to avoid functionality
issues like h8 enter/exit failure, command timeout.
Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20230905052400.13935-4-quic_nitirawa@quicinc.com
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Qualcomm UFS Controller V4 and above supports multiple unipro frequencies
like 403MHz, 300MHz, 202MHz, 150 MHz, 75Mhz, 37.5 MHz. Current code
supports only 150MHz and 75MHz which have performance impact due to low UFS
controller frequencies.
For targets which supports frequencies other than 150 MHz and 75 Mhz, needs
an update of MAX_CORE_CLK_1US_CYCLES to match the configured frequency to
avoid functionality issues. Add multiple frequency support for
MAX_CORE_CLK_1US_CYCLES based on the frequency configured.
Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20230905052400.13935-3-quic_nitirawa@quicinc.com
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS Controller V4 and above, the register layout for DME_VS_CORE_CLK_CTRL
register has changed. MAX_CORE_CLK_1US_CYCLES offset has changed from 0 to
0x10 and length of attrbute is changed from 8bit to 12bit.
Add support to configure MAX_CORE_CLK_1US_CYCLES for UFS V4 and above as
per new register layout.
Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20230905052400.13935-2-quic_nitirawa@quicinc.com
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The qunipro_g4_sel clear is also needed for new platforms with major
version > 5. Fix the version check to take this into account.
Fixes: 9c02aa24bf ("scsi: ufs: ufs-qcom: Clear qunipro_g4_sel for HW version major 5")
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230821-topic-sm8x50-upstream-ufs-major-5-plus-v2-1-f42a4b712e58@linaro.org
Reviewed-by: "Bao D. Nguyen" <quic_nguyenb@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche <bvanassche@acm.org> says:
Hi Martin,
This patch includes the following changes, none of which should change the
functionality of the UFS host controller driver:
- Improve the kernel-doc headers further.
- Fix multiple W=2 compiler warnings.
- Simplify ufshcd_abort_all().
- Simplify the code for creating and parsing UFS Transport Protocol (UTP)
headers.
Please consider this patch series for the next merge window.
Thanks,
Bart.
Link: https://lore.kernel.org/r/20230727194457.3152309-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use 'Return:' to document the return value instead of 'Returns' as required
by the kernel-doc documentation.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230727194457.3152309-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Qcom SoCs require scaling the interconnect paths for proper working of the
peripherals connected through interconnects. Even for accessing the UFS
controller, someone should setup the interconnect paths. So far, the
bootloaders used to setup the interconnect paths before booting Linux as
they need to access the UFS storage for things like fetching boot firmware.
But with the advent of multi boot options, bootloader nowadays like in
SA8540p SoC do not setup the interconnect paths at all.
So trying to configure UFS in the absence of the interconnect path
configuration results in a boot crash.
To fix this issue, and also to dynamically scale the interconnects (UFS-DDR
and CPU-UFS), interconnect API support is added to the Qcom UFS driver.
With this support, the interconnect paths are scaled dynamically based on
the gear configuration.
During the early stage of ufs_qcom_init(), ufs_qcom_icc_init() will setup
the paths to max bandwidth to allow configuring the UFS registers. Touching
the registers without configuring the icc paths would result in a crash.
However, we don't really need to set max vote for the icc paths as any
minimal vote would suffice. But the max value would allow initialization to
be done faster. After init, the bandwidth will get updated using
ufs_qcom_icc_update_bw() based on the gear and lane configuration.
The bandwidth values defined in ufs_qcom_bw_table struct are taken from
Qcom downstream vendor devicetree source and are calculated as per the
UFS3.1 Spec, Section 6.4.1, HS Gear Rates. So it is fixed across platforms.
Cc: Brian Masney <bmasney@redhat.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230731145020.41262-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent change removed the only user of a local variable that needs to now
also be removed:
drivers/ufs/host/ufs-qcom.c: In function 'ufs_qcom_mcq_esi_handler':
drivers/ufs/host/ufs-qcom.c:1652:31: error: unused variable 'host' [-Werror=unused-variable]
Fixes: 8f2b78652d ("scsi: ufs: qcom: Get queue ID from MSI index in ESI handler")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/llvm/64c00cd4.630a0220.6ad79.0eac@mx.google.com/
Link: https://lore.kernel.org/r/20230724122029.1430482-1-arnd@kernel.org
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Devfreq uses the default DEVFREQ_TIMER_DEFERRABLE mode which uses the
deferred timer for scheduling the devfreq load monitor function. This
causes the load monitoring to be done only with non-idle CPUs and not
making use of the idle CPUs.
Hence, use the DEVFREQ_TIMER_DELAYED mode which uses the delayed timer
thereby making use of idle CPUs as well for load monitoring.
Co-developed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20230720093446.30697-1-quic_nitirawa@quicinc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
platform_msi_domain_alloc_irqs() does not always get consecutive IRQ
numbers, hence queue IDs calculated out from IRQ numbers may be incorrect
if we assume IRQ numbers are consecutive. Fix this by passing msi_desc to
ESI handler to use msi_desc->msi_index as queue ID.
Co-developed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Ziqi Chen <quic_ziqichen@quicinc.com>
Link: https://lore.kernel.org/r/1689062349-77385-1-git-send-email-quic_ziqichen@quicinc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that there is a new dedicated ICE driver, drop the ufs-qcom-ice and use
the new ICE api provided by the Qualcomm soc driver ice. The platforms that
already have ICE support will use the API as library since there will not
be a devicetree node, but instead they have reg range. In this case, the
of_qcom_ice_get will return an ICE instance created for the consumer's
device. But if there are platforms that do not have ice reg in the consumer
devicetree node and instead provide a dedicated ICE devicetree node, the
of_qcom_ice_get will look up the device based on qcom,ice property and will
get the ICE instance registered by the probe function of the ice driver.
The ICE clock is now handle by the new driver. This is done by enabling it
on the creation of the ICE instance and then enabling/disabling it on UFS
runtime resume/suspend.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230612192847.1599416-3-abel.vesa@linaro.org
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All UFS host drivers call ufshcd_shutdown(). Hence, instead of calling
ufshcd_shutdown() from the host driver .shutdown() callback, inline that
function into ufshcd_wl_shutdown().
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230524203659.1394307-5-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation for adding MCQ error handler support, update the MCQ code to
use the ufshcd_mcq_poll_cqe_lock() in interrupt context instead of using
ufshcd_mcq_poll_cqe_nolock(). This is to keep synchronization between MCQ
interrupt and error handler contexts because both need to access the MCQ
hardware in separate contexts.
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Link: https://lore.kernel.org/r/6ae727ad2a4040469b8f0632b55e0577d80da11b.1685396241.git.quic_nguyenb@quicinc.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Tested-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver can be built on ACPI and its .of_match_table uses
of_match_ptr(), thus annotate the actual table as maybe unused.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230310214435.275127-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Smatch static checker reported:
drivers/ufs/host/ufs-qcom.c:1469
ufs_qcom_mcq_config_resource() info: returning a literal zero is
cleaner
Fix the above warning by returning in place instead of a jump to a label.
Also remove the usage of devm_kfree() as it's unnecessary in this function.
Fixes: c263b4ef73 ("scsi: ufs: core: mcq: Configure resource regions")
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Link: https://lore.kernel.org/r/3ebd2582af74b81ef7b57149f57c6a3bf0963953.1677721229.git.quic_asutoshd@quicinc.com
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix an error case in ufs_qcom_mcq_config_resource(), where the return value
is set to 0 before passing it to PTR_ERR.
This led to Smatch warning:
drivers/ufs/host/ufs-qcom.c:1455 ufs_qcom_mcq_config_resource() warn:
passing zero to 'PTR_ERR'
Fixes: c263b4ef73 ("scsi: ufs: core: mcq: Configure resource regions")
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Link: https://lore.kernel.org/r/94ca99b327af634799ce5f25d0112c28cd00970d.1677721072.git.quic_asutoshd@quicinc.com
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "dev_req_params" pointer points to inside the middle of a struct so it
can't be NULL. Removing this impossible condition is nice because now we
don't need to consider the correct error code for that situation.
Link: https://lore.kernel.org/r/Y/yA3niWUcGYgBU8@kili
Fixes: f06fcc7155 ("scsi: ufs-qcom: add QUniPro hardware support and power optimizations")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add freeze, thaw, and restore callbacks for hibernate and restore
functionality.
Link: https://lore.kernel.org/r/20230202161045.3956-2-quic_ahari@quicinc.com
Signed-off-by: Anjana Hari <quic_ahari@quicinc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On SM8550, depending on the Qunipro, we can run with G5 or G4. For now,
when the major version is 5 or above, we go with G5. Therefore, we need to
specifically tell UFS HC that.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The newly added MSI support is mostly hidden inside of an #ifdef,
except for one line that now causes a build failure when MSI
is disabled:
drivers/ufs/host/ufs-qcom.c: In function 'ufs_qcom_remove':
drivers/ufs/host/ufs-qcom.c:1698:9: error: implicit declaration of function 'platform_msi_domain_free_irqs' [-Werror=i]
1698 | platform_msi_domain_free_irqs(hba->dev);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Above that, the symbol that guards the other call was recently removed, so
that is all dead code at the moment.
Remove the incorrect #ifdef and instead of a Kconfig dependency to only
allow building the driver when CONFIG_GENERIC_MSI_IRQ is enabled. This
symbol is always present when PCI_MSI or ARM_GIC_V3_ITS are enabled, both
of which should be present on kernels that can run on Qualcomm SoCs.
The 'select RESET_CONTROLLER' in combination with this dependency
unfortunately causes a dependency loop and this is a user-visible symbol,
so it's better to change both to 'depends on'.
Link: https://lore.kernel.org/r/20230126211831.2274211-1-arnd@kernel.org
Fixes: 519b6274a7 ("scsi: ufs: qcom: Add MCQ ESI config vendor specific ops")
Fixes: 13e7accb81 ("genirq: Get rid of GENERIC_MSI_IRQ_DOMAIN")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add MCQ ESI config vendor specific ops.
Co-developed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for completing requests from Completion Queue. Some host
controllers support vendor specific registers that provide a bitmap of all
CQs which have at least one completed CQE. Add this support. The MCQ
specification doesn't provide the Task Tag or its equivalent in the
Completion Queue Entry. So use an indirect method to find the Task Tag
from the Completion Queue Entry.
Co-developed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Runtime and operation registers are defined per Submission and Completion
queue. The location of these registers is not defined in the spec; meaning
the offsets and stride may vary for different HC vendors. Establish the
stride, base address, and doorbell address offsets from vendor host driver
and program it.
Co-developed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFS device defines the supported queuedepth by bqueuedepth which has a
max value of 256. The HC defines MAC (Max Active Commands) that defines
the max number of commands that in flight to the UFS device. Calculate and
configure the nutrs based on both these values.
Co-developed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Define the MCQ resources and add support to ioremap the resource regions.
Co-developed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Asutosh Das <quic_asutoshd@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Starting from Qcom UFS version 4.0, vendor specific REG_UFS_PARAM0 register
can be used to determine the maximum gear supported by the controller.
Suggested-by: Can Guo <quic_cang@quicinc.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Starting from Qualcomm UFS version 4, the UFS device needs to be
reinitialized after switching to maximum gear by the UFS core. Hence, add
support for it by enabling the UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH
quirk, implementing reinit_notify() callback and using the agreed gear
speed for setting the PHY mode.
Suggested-by: Can Guo <quic_cang@quicinc.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the preparation of adding support for new gears, move the logic that
finds the gear for each platform to a new function. This helps with code
readability and also allows the logic to be used in other places of the
driver in future.
While at it, make it clear that this driver only supports symmetric gear
setting (hs_tx_gear == hs_rx_gear).
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make use of dev_err_probe() for printing the probe error.
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the reset assert and deassert callbacks, the supplied "id" is not used
at all and only the HBA reset is performed all the time. So there is no
reason to use a WARN_ON() on the "id".
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A goto statement in an error path is useful if the function needs to do
cleanup other than returning the error code. But in this driver, goto
statements are used for just returning the error code in many places. This
really makes it hard to read the code.
Get rid of those goto statements and just return the error code directly.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
dev_err() statements are better to use than pr_err(), so switch to those.
In a similar vein, the check on the dev_req_params pointer here is not
needed, the two places this function is called never pass in a NULL
pointer, so instead of using dev_err() there just remove it.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This bitmask is unconditionally set in the current driver, so all
conditionals using it can be considered bit rot.
Let's take the current default conditional path everywhere and remove
dbg_print_en from the driver.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current implementation has abstractions that don't give any benefits.
The print_fn callback (and its only callback implementation,
ufs_qcom_dump_regs_wrapper()) was only used by
ufs_qcom_print_hw_debug_reg_all() and just multiplies len by 4 before
calling ufshcd_dump_regs().
ufs_qcom_print_hw_debug_reg_all() is only called by
ufs_qcom_dump_dbg_regs().
There's no real gain in those abstractions, so let's just do the work
directly in ufs_qcom_dump_dbg_regs() (the dbg_register_dump callback).
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code path is only called through one function, and the HBA struct is
already accessed in ufshcd_vops_dbg_register_dump() prior to calling so
there is no way for it to be NULL.
Likewise, the print_fn callback is always supplied within this driver and
is always provided.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Asutosh Das <quic_asutoshd@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mediatek UFS does not want to toggle write booster during clock scaling.
Permit host driver to disable wb toggling during clock scaling.
Introduce a flag UFSHCD_CAP_WB_WITH_CLK_SCALING to decouple WB and clock
scaling. UFSHCD_CAP_WB_WITH_CLK_SCALING is only valid when
UFSHCD_CAP_CLK_SCALING is set. Just like UFSHCD_CAP_HIBERN8_WITH_CLK_GATING
is valid only when UFSHCD_CAP_CLK_GATING set.
Set UFSHCD_CAP_WB_WITH_CLK_SCALING for qcom to compatible legacy design at
the same time.
Link: https://lore.kernel.org/r/20220804025422.18803-1-peter.wang@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
