On the Renesas RZ/G3S, when doing suspend to RAM, the uart_suspend_port()
is called. The uart_suspend_port() calls 3 times the
struct uart_port::ops::tx_empty() before shutting down the port.
According to the documentation, the struct uart_port::ops::tx_empty()
API tests whether the transmitter FIFO and shifter for the port is
empty.
The Renesas RZ/G3S SCIFA IP reports the number of data units stored in the
transmit FIFO through the FDR (FIFO Data Count Register). The data units
in the FIFOs are written in the shift register and transmitted from there.
The TEND bit in the Serial Status Register reports if the data was
transmitted from the shift register.
In the previous code, in the tx_empty() API implemented by the sh-sci
driver, it is considered that the TX is empty if the hardware reports the
TEND bit set and the number of data units in the FIFO is zero.
According to the HW manual, the TEND bit has the following meaning:
0: Transmission is in the waiting state or in progress.
1: Transmission is completed.
It has been noticed that when opening the serial device w/o using it and
then switch to a power saving mode, the tx_empty() call in the
uart_port_suspend() function fails, leading to the "Unable to drain
transmitter" message being printed on the console. This is because the
TEND=0 if nothing has been transmitted and the FIFOs are empty. As the
TEND=0 has double meaning (waiting state, in progress) we can't
determined the scenario described above.
Add a software workaround for this. This sets a variable if any data has
been sent on the serial console (when using PIO) or if the DMA callback has
been called (meaning something has been transmitted). In the tx_empty()
API the status of the DMA transaction is also checked and if it is
completed or in progress the code falls back in checking the hardware
registers instead of relying on the software variable.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241125115856.513642-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parport_serial driver uses subset of WCH IDs that are present in 8250_pci.
Share them via pci_ids.h and switch parport_serial to use defined constants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20241204031114.1029882-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two sites of the same brand: wch.cn and wch-ic.com.
They are property of the same company, but it appears that they
managed to get two different PCI vendor IDs. Rename them accordingly
using standard pattern, i.e. PCI_VENDOR_ID_...
While at it, move to PCI_VDEVICE() in the ID tables.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20241204031114.1029882-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_init_port() assings 0xFF for the unset or unknown port
IO type, use predefined constant for that instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20241125103305.1614986-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using memcpy() prevents the compiler from doing any checking on the
types of the passed pointer parameters. Copy the structure using struct
assignment instead, to increase type-safety.
No change in generated code on all relevant architectures
(arm/arm64/riscv/sh).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/e097e5c11afe5bd4c01135779c9a40e707ef6374.1733243287.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The request_irq name parameter should be the device name, not the driver
name. This leads to more informative information in /proc/interrupts.
Before this patch:
$ cat /proc/interrupts
...
40: 123 0 GIC-0 72 Level altera_jtaguart
After this patch:
$ cat /proc/interrupts
...
40: 6 0 GIC-0 72 Level ff200100.fpga-juart0
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20241203132556.14182-1-tklauser@distanz.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cdd30ebb1b ("module: Convert symbol namespace to string
literal") only converted MODULE_IMPORT_NS() and EXPORT_SYMBOL_NS(),
leaving DEFAULT_SYMBOL_NAMESPACE as a macro expansion.
This commit converts DEFAULT_SYMBOL_NAMESPACE in the same way to avoid
annoyance for the default namespace as well.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is a small set of tty and serial driver updates for 6.13-rc1.
Nothing major at all this time, only some small changes:
- few device tree binding updates
- 8250_exar serial driver updates
- imx serial driver updates
- sprd_serial driver updates
- other tiny serial driver updates, full details in the shortlog
All of these have been in linux-next for a while with one reported
issue, but that commit has now been reverted.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ0s3DA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykmgQCeIDU0GHWFuzEiZNmsO5bLN8AcoFQAn1rlOaHu
9lOOf7xVSCUBU0GgynI5
=SEtJ
-----END PGP SIGNATURE-----
Merge tag 'tty-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is a small set of tty and serial driver updates for 6.13-rc1.
Nothing major at all this time, only some small changes:
- few device tree binding updates
- 8250_exar serial driver updates
- imx serial driver updates
- sprd_serial driver updates
- other tiny serial driver updates, full details in the shortlog
All of these have been in linux-next for a while with one reported
issue, but that commit has now been reverted"
* tag 'tty-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (37 commits)
Revert "serial: sh-sci: Clean sci_ports[0] after at earlycon exit"
serial: amba-pl011: fix build regression
dt-bindings: serial: Add a new compatible string for ums9632
serial: sprd: Add support for sc9632
tty/serial/altera_uart: unwrap error log string
tty/serial/altera_jtaguart: unwrap error log string
serial: amba-pl011: Fix RX stall when DMA is used
tty: ldsic: fix tty_ldisc_autoload sysctl's proc_handler
serial: 8250_fintek: Add support for F81216E
serial: sh-sci: Clean sci_ports[0] after at earlycon exit
tty: atmel_serial: Fix typo retreives to retrieves
tty: atmel_serial: Use devm_platform_ioremap_resource()
serial: 8250: omap: Move pm_runtime_get_sync
tty: serial: samsung: Add Exynos8895 compatible
dt-bindings: serial: samsung: Add samsung,exynos8895-uart compatible
serial: 8250_dw: Add Sophgo SG2044 quirk
dt-bindings: serial: snps-dw-apb-uart: Add Sophgo SG2044 uarts
dt-bindings: serial: snps,dw-apb-uart: merge duplicate compatible entry.
altera_jtaguart: Use dev_err() to report error attaching IRQ
altera_uart: Use dev_err() to report error attaching IRQ handler
...
This reverts commit 3791ea69a4.
It was reported to cause boot-time issues, so revert it for now.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 3791ea69a4 ("serial: sh-sci: Clean sci_ports[0] after at earlycon exit")
Cc: stable <stable@kernel.org>
Cc: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=2Otz
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Make pci_stop_dev() and pci_destroy_dev() safe so concurrent
callers can't stop a device multiple times, even as we migrate from
the global pci_rescan_remove_lock to finer-grained locking (Keith
Busch)
- Improve pci_walk_bus() implementation by making it recursive and
moving locking up to avoid need for a 'locked' parameter (Keith
Busch)
- Unexport pci_walk_bus_locked(), which is only used internally by
the PCI core (Keith Busch)
- Detect some Thunderbolt chips that are built-in and hence
'trustworthy' by a heuristic since the 'ExternalFacingPort' and
'usb4-host-interface' ACPI properties are not quite enough (Esther
Shimanovich)
Resource management:
- Use PCI bus addresses (not CPU addresses) in 'ranges' properties
when building dynamic DT nodes so systems where PCI and CPU
addresses differ work correctly (Andrea della Porta)
- Tidy resource sizing and assignment with helpers to reduce
redundancy (Ilpo Järvinen)
- Improve pdev_sort_resources() 'bogus alignment' warning to be more
specific (Ilpo Järvinen)
Driver binding:
- Convert driver .remove_new() callbacks to .remove() again to finish
the conversion from returning 'int' to being 'void' (Sergio
Paracuellos)
- Export pcim_request_all_regions(), a managed interface to request
all BARs (Philipp Stanner)
- Replace pcim_iomap_regions_request_all() with
pcim_request_all_regions(), and pcim_iomap_table()[n] with
pcim_iomap(n), in the following drivers: ahci, crypto qat, crypto
octeontx2, intel_th, iwlwifi, ntb idt, serial rp2, ALSA korg1212
(Philipp Stanner)
- Remove the now unused pcim_iomap_regions_request_all() (Philipp
Stanner)
- Export pcim_iounmap_region(), a managed interface to unmap and
release a PCI BAR (Philipp Stanner)
- Replace pcim_iomap_regions(mask) with pcim_iomap_region(n), and
pcim_iounmap_regions(mask) with pcim_iounmap_region(n), in the
following drivers: fpga dfl-pci, block mtip32xx, gpio-merrifield,
cavium (Philipp Stanner)
Error handling:
- Add sysfs 'reset_subordinate' to reset the entire hierarchy below a
bridge; previously Secondary Bus Reset could only be used when
there was a single device below a bridge (Keith Busch)
- Warn if we reset a running device where the driver didn't register
pci_error_handlers notification callbacks (Keith Busch)
ASPM:
- Disable ASPM L1 before touching L1 PM Substates to follow the spec
closer and avoid a CPU load timeout on some platforms (Ajay
Agarwal)
- Set devices below Intel VMD to D0 before enabling ASPM L1 Substates
as required per spec for all L1 Substates changes (Jian-Hong Pan)
Power management:
- Enable starfive controller runtime PM before probing host bridge
(Mayank Rana)
- Enable runtime power management for host bridges (Krishna chaitanya
chundru)
Power control:
- Use of_platform_device_create() instead of of_platform_populate()
to create pwrctl platform devices so we can control it based on the
child nodes (Manivannan Sadhasivam)
- Create pwrctrl platform devices only if there's a relevant power
supply property (Manivannan Sadhasivam)
- Add device link from the pwrctl supplier to the PCI dev to ensure
pwrctl drivers are probed before the PCI dev driver; this avoids a
race where pwrctl could change device power state while the PCI
driver was active (Manivannan Sadhasivam)
- Find pwrctl device for removal with of_find_device_by_node()
instead of searching all children of the parent (Manivannan
Sadhasivam)
- Rename 'pwrctl' to 'pwrctrl' to match new bandwidth controller
('bwctrl') and hotplug files (Bjorn Helgaas)
Bandwidth control:
- Add read/modify/write locking for Link Control 2, which is used to
manage Link speed (Ilpo Järvinen)
- Extract Link Bandwidth Management Status check into
pcie_lbms_seen(), where it can be shared between the bandwidth
controller and quirks that use it to help retrain failed links
(Ilpo Järvinen)
- Re-add Link Bandwidth notification support with updates to address
the reasons it was previously reverted (Alexandru Gagniuc, Ilpo
Järvinen)
- Add pcie_set_target_speed() and related functionality so drivers
can manage PCIe Link speed based on thermal or other constraints
(Ilpo Järvinen)
- Add a thermal cooling driver to throttle PCIe Links via the
existing thermal management framework (Ilpo Järvinen)
- Add a userspace selftest for the PCIe bandwidth controller (Ilpo
Järvinen)
PCI device hotplug:
- Add hotplug controller driver for Marvell OCTEON multi-function
device where function 0 has a management console interface to
enable/disable and provision various personalities for the other
functions (Shijith Thotton)
- Retain a reference to the pci_bus for the lifetime of a pci_slot to
avoid a use-after-free when the thunderbolt driver resets USB4 host
routers on boot, causing hotplug remove/add of downstream docks or
other devices (Lukas Wunner)
- Remove unused cpcihp struct cpci_hp_controller_ops.hardware_test
(Guilherme Giacomo Simoes)
- Remove unused cpqphp struct ctrl_dbg.ctrl (Christophe JAILLET)
- Use pci_bus_read_dev_vendor_id() instead of hand-coded presence
detection in cpqphp (Ilpo Järvinen)
- Simplify cpqphp enumeration, which is already simple-minded and
doesn't handle devices below hot-added bridges (Ilpo Järvinen)
Virtualization:
- Add ACS quirk for Wangxun FF5xxx NICs, which don't advertise an ACS
capability but do isolate functions as though PCI_ACS_RR and
PCI_ACS_CR were set, so the functions can be in independent IOMMU
groups (Mengyuan Lou)
TLP Processing Hints (TPH):
- Add and document TLP Processing Hints (TPH) support so drivers can
enable and disable TPH and the kernel can save/restore TPH
configuration (Wei Huang)
- Add TPH Steering Tag support so drivers can retrieve Steering Tag
values associated with specific CPUs via an ACPI _DSM to improve
performance by directing DMA writes closer to their consumers (Wei
Huang)
Data Object Exchange (DOE):
- Wait up to 1 second for DOE Busy bit to clear before writing a
request to the mailbox to avoid failures if the mailbox is still
busy from a previous transfer (Gregory Price)
Endpoint framework:
- Skip attempts to allocate from endpoint controller memory window if
the requested size is larger than the window (Damien Le Moal)
- Add and document pci_epc_mem_map() and pci_epc_mem_unmap() to
handle controller-specific size and alignment constraints, and add
test cases to the endpoint test driver (Damien Le Moal)
- Implement dwc pci_epc_ops.align_addr() so pci_epc_mem_map() can
observe DWC-specific alignment requirements (Damien Le Moal)
- Synchronously cancel command handler work in endpoint test before
cleaning up DMA and BARs (Damien Le Moal)
- Respect endpoint page size in dw_pcie_ep_align_addr() (Niklas
Cassel)
- Use dw_pcie_ep_align_addr() in dw_pcie_ep_raise_msi_irq() and
dw_pcie_ep_raise_msix_irq() instead of open coding the equivalent
(Niklas Cassel)
- Avoid NULL dereference if Modem Host Interface Endpoint lacks
'mmio' DT property (Zhongqiu Han)
- Release PCI domain ID of Endpoint controller parent (not controller
itself) and before unregistering the controller, to avoid
use-after-free (Zijun Hu)
- Clear secondary (not primary) EPC in pci_epc_remove_epf() when
removing the secondary controller associated with an NTB (Zijun Hu)
Cadence PCIe controller driver:
- Lower severity of 'phy-names' message (Bartosz Wawrzyniak)
Freescale i.MX6 PCIe controller driver:
- Fix suspend/resume support on i.MX6QDL, which has a hardware
erratum that prevents use of L2 (Stefan Eichenberger)
Intel VMD host bridge driver:
- Add 0xb60b and 0xb06f Device IDs for client SKUs (Nirmal Patel)
MediaTek PCIe Gen3 controller driver:
- Update mediatek-gen3 DT binding to require the exact number of
clocks for each SoC (Fei Shao)
- Add support for DT 'max-link-speed' and 'num-lanes' properties to
restrict the link speed and width (AngeloGioacchino Del Regno)
Microchip PolarFlare PCIe controller driver:
- Add DT and driver support for using either of the two PolarFire
Root Ports (Conor Dooley)
NVIDIA Tegra194 PCIe controller driver:
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
Qualcomm PCIe controller driver:
- Add qcom SAR2130P DT binding with an additional clock (Dmitry
Baryshkov)
- Enable MSI interrupts if 'global' IRQ is supported, since a
previous commit unintentionally masked them (Manivannan Sadhasivam)
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
- Add DT binding and driver support for IPQ9574, with Synopsys IP
v5.80a and Qcom IP 1.27.0 (devi priya)
- Move the OPP "operating-points-v2" table from the
qcom,pcie-sm8450.yaml DT binding to qcom,pcie-common.yaml, where it
can be used by other Qcom platforms (Qiang Yu)
- Add 'global' SPI interrupt for events like link-up, link-down to
qcom,pcie-x1e80100 DT binding so we can start enumeration when the
link comes up (Qiang Yu)
- Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned
to support this (Qiang Yu)
- Add ops_1_21_0 for SC8280X family SoC, which doesn't use the
'iommu-map' DT property and doesn't need BDF-to-SID translation
(Qiang Yu)
Rockchip PCIe controller driver:
- Define ROCKCHIP_PCIE_AT_SIZE_ALIGN to replace magic 256 endpoint
.align value (Damien Le Moal)
- When unmapping an endpoint window, compute the region index instead
of searching for it, and verify that the address was mapped (Damien
Le Moal)
- When mapping an endpoint window, verify that the address hasn't
been mapped already (Damien Le Moal)
- Implement pci_epc_ops.align_addr() for rockchip-ep (Damien Le Moal)
- Fix MSI IRQ data mapping to observe the alignment constraint, which
fixes intermittent page faults in memcpy_toio() and memcpy_fromio()
(Damien Le Moal)
- Rename rockchip_pcie_parse_ep_dt() to
rockchip_pcie_ep_get_resources() for consistency with similar DT
interfaces (Damien Le Moal)
- Skip the unnecessary link train in rockchip_pcie_ep_probe() and do
it only in the endpoint start operation (Damien Le Moal)
- Implement pci_epc_ops.stop_link() to disable link training and
controller configuration (Damien Le Moal)
- Attempt link training at 5 GT/s when both partners support it
(Damien Le Moal)
- Add a handler for PERST# signal so we can detect host-initiated
resets and start link training after PERST# is deasserted (Damien
Le Moal)
Synopsys DesignWare PCIe controller driver:
- Clear outbound address on unmap so dw_pcie_find_index() won't match
an ATU index that was already unmapped (Damien Le Moal)
- Use of_property_present() instead of of_property_read_bool() when
testing for presence of non-boolean DT properties (Rob Herring)
- Advertise 1MB size if endpoint supports Resizable BARs, which was
inadvertently lost in v6.11 (Niklas Cassel)
TI J721E PCIe driver:
- Add PCIe support for J722S SoC (Siddharth Vadapalli)
- Delay PCIE_T_PVPERL_MS (100 ms), not just PCIE_T_PERST_CLK_US (100
us), before deasserting PERST# to ensure power and refclk are
stable (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Set the 'ti,keystone-pcie' mode so v3.65a devices work in Root
Complex mode (Kishon Vijay Abraham I)
- Try to avoid unrecoverable SError for attempts to issue config
transactions when the link is down; this is racy but the best we
can do (Kishon Vijay Abraham I)
Miscellaneous:
- Reorganize kerneldoc parameter names to match order in function
signature (Julia Lawall)
- Fix sysfs reset_method_store() memory leak (Todd Kjos)
- Simplify pci_create_slot() (Ilpo Järvinen)
- Fix incorrect printf format specifiers in pcitest (Luo Yifan)"
* tag 'pci-v6.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (127 commits)
PCI: rockchip-ep: Handle PERST# signal in EP mode
PCI: rockchip-ep: Improve link training
PCI: rockship-ep: Implement the pci_epc_ops::stop_link() operation
PCI: rockchip-ep: Refactor endpoint link training enable
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() MSI-X hiding
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() memory allocations
PCI: rockchip-ep: Rename rockchip_pcie_parse_ep_dt()
PCI: rockchip-ep: Fix MSI IRQ data mapping
PCI: rockchip-ep: Implement the pci_epc_ops::align_addr() operation
PCI: rockchip-ep: Improve rockchip_pcie_ep_map_addr()
PCI: rockchip-ep: Improve rockchip_pcie_ep_unmap_addr()
PCI: rockchip-ep: Use a macro to define EP controller .align feature
PCI: rockchip-ep: Fix address translation unit programming
PCI/pwrctrl: Rename pwrctrl functions and structures
PCI/pwrctrl: Rename pwrctl files to pwrctrl
PCI/pwrctl: Remove pwrctl device without iterating over all children of pwrctl parent
PCI/pwrctl: Ensure that pwrctl drivers are probed before PCI client drivers
PCI/pwrctl: Create pwrctl device only if at least one power supply is present
PCI/pwrctl: Use of_platform_device_create() to create pwrctl devices
tools: PCI: Fix incorrect printf format specifiers
...
These are a number of unrelated cleanups, generally simplifying the
architecture specific header files:
- A series from Al Viro simplifies asm/vga.h, after it turns out that
most of it can be generalized.
- A series from Julian Vetter adds a common version of
memcpy_{to,from}io() and memset_io() and changes most architectures
to use that instead of their own implementation
- A series from Niklas Schnelle concludes his work to make PC
style inb()/outb() optional
- Nicolas Pitre contributes improvements for the generic do_div()
helper
- Christoph Hellwig adds a generic version of page_to_phys()
and phys_to_page(), replacing the slightly different architecture
specific definitions.
- Uwe Kleine-Koenig has a minor cleanup for ioctl definitions
-----BEGIN PGP SIGNATURE-----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=zEHk
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"These are a number of unrelated cleanups, generally simplifying the
architecture specific header files:
- A series from Al Viro simplifies asm/vga.h, after it turns out that
most of it can be generalized.
- A series from Julian Vetter adds a common version of
memcpy_{to,from}io() and memset_io() and changes most architectures
to use that instead of their own implementation
- A series from Niklas Schnelle concludes his work to make PC style
inb()/outb() optional
- Nicolas Pitre contributes improvements for the generic do_div()
helper
- Christoph Hellwig adds a generic version of page_to_phys() and
phys_to_page(), replacing the slightly different architecture
specific definitions.
- Uwe Kleine-Koenig has a minor cleanup for ioctl definitions"
* tag 'asm-generic-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (24 commits)
empty include/asm-generic/vga.h
sparc: get rid of asm/vga.h
asm/vga.h: don't bother with scr_mem{cpy,move}v() unless we need to
vt_buffer.h: get rid of dead code in default scr_...() instances
tty: serial: export serial_8250_warn_need_ioport
lib/iomem_copy: fix kerneldoc format style
hexagon: simplify asm/io.h for !HAS_IOPORT
loongarch: Use new fallback IO memcpy/memset
csky: Use new fallback IO memcpy/memset
arm64: Use new fallback IO memcpy/memset
New implementation for IO memcpy and IO memset
watchdog: Add HAS_IOPORT dependency for SBC8360 and SBC7240
__arch_xprod64(): make __always_inline when optimizing for performance
ARM: div64: improve __arch_xprod_64()
asm-generic/div64: optimize/simplify __div64_const32()
lib/math/test_div64: add some edge cases relevant to __div64_const32()
asm-generic: add an optional pfn_valid check to page_to_phys
asm-generic: provide generic page_to_phys and phys_to_page implementations
asm-generic/io.h: Remove I/O port accessors for HAS_IOPORT=n
tty: serial: handle HAS_IOPORT dependencies
...
-----BEGIN PGP SIGNATURE-----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=89Bg
-----END PGP SIGNATURE-----
Merge tag 'printk-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Print more precise information about the printk log buffer memory
usage.
- Make sure that the sysrq title is shown on the console even when
deferred.
- Do not enable earlycon by `console=` which is meant to disable the
default console.
* tag 'printk-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: add dummy printk_force_console_enter/exit helpers
tty: sysrq: Use printk_force_console context on __handle_sysrq
printk: Introduce FORCE_CON flag
printk: Improve memory usage logging during boot
init: Don't proxy `console=` to earlycon
- Tree wide:
* Make nr_irqs static to the core code and provide accessor functions
to remove existing and prevent future aliasing problems with local
variables or function arguments of the same name.
- Core code:
* Prevent freeing an interrupt in the devres code which is not managed
by devres in the first place.
* Use seq_put_decimal_ull_width() for decimal values output in
/proc/interrupts which increases performance significantly as it
avoids parsing the format strings over and over.
* Optimize raising the timer and hrtimer soft interrupts by using the
'set bit only' variants instead of the combined version which checks
whether ksoftirqd should be woken up. The latter is a pointless
exercise as both soft interrupts are raised in the context of the
timer interrupt and therefore never wake up ksoftirqd.
* Delegate timer/hrtimer soft interrupt processing to a dedicated thread
on RT.
Timer and hrtimer soft interrupts are always processed in ksoftirqd
on RT enabled kernels. This can lead to high latencies when other
soft interrupts are delegated to ksoftirqd as well.
The separate thread allows to run them seperately under a RT
scheduling policy to reduce the latency overhead.
- Drivers:
* New drivers or extensions of existing drivers to support Renesas
RZ/V2H(P), Aspeed AST27XX, T-HEAD C900 and ATMEL sam9x7 interrupt
chips
* Support for multi-cluster GICs on MIPS.
MIPS CPUs can come with multiple CPU clusters, where each CPU cluster
has its own GIC (Generic Interrupt Controller). This requires to
access the GIC of a remote cluster through a redirect register block.
This is encapsulated into a set of helper functions to keep the
complexity out of the actual code paths which handle the GIC details.
* Support for encrypted guests in the ARM GICV3 ITS driver
The ITS page needs to be shared with the hypervisor and therefore
must be decrypted.
* Small cleanups and fixes all over the place
-----BEGIN PGP SIGNATURE-----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=JqxC
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2024-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt subsystem updates from Thomas Gleixner:
"Tree wide:
- Make nr_irqs static to the core code and provide accessor functions
to remove existing and prevent future aliasing problems with local
variables or function arguments of the same name.
Core code:
- Prevent freeing an interrupt in the devres code which is not
managed by devres in the first place.
- Use seq_put_decimal_ull_width() for decimal values output in
/proc/interrupts which increases performance significantly as it
avoids parsing the format strings over and over.
- Optimize raising the timer and hrtimer soft interrupts by using the
'set bit only' variants instead of the combined version which
checks whether ksoftirqd should be woken up. The latter is a
pointless exercise as both soft interrupts are raised in the
context of the timer interrupt and therefore never wake up
ksoftirqd.
- Delegate timer/hrtimer soft interrupt processing to a dedicated
thread on RT.
Timer and hrtimer soft interrupts are always processed in ksoftirqd
on RT enabled kernels. This can lead to high latencies when other
soft interrupts are delegated to ksoftirqd as well.
The separate thread allows to run them seperately under a RT
scheduling policy to reduce the latency overhead.
Drivers:
- New drivers or extensions of existing drivers to support Renesas
RZ/V2H(P), Aspeed AST27XX, T-HEAD C900 and ATMEL sam9x7 interrupt
chips
- Support for multi-cluster GICs on MIPS.
MIPS CPUs can come with multiple CPU clusters, where each CPU
cluster has its own GIC (Generic Interrupt Controller). This
requires to access the GIC of a remote cluster through a redirect
register block.
This is encapsulated into a set of helper functions to keep the
complexity out of the actual code paths which handle the GIC
details.
- Support for encrypted guests in the ARM GICV3 ITS driver
The ITS page needs to be shared with the hypervisor and therefore
must be decrypted.
- Small cleanups and fixes all over the place"
* tag 'irq-core-2024-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
irqchip/riscv-aplic: Prevent crash when MSI domain is missing
genirq/proc: Use seq_put_decimal_ull_width() for decimal values
softirq: Use a dedicated thread for timer wakeups on PREEMPT_RT.
timers: Use __raise_softirq_irqoff() to raise the softirq.
hrtimer: Use __raise_softirq_irqoff() to raise the softirq
riscv: defconfig: Enable T-HEAD C900 ACLINT SSWI drivers
irqchip: Add T-HEAD C900 ACLINT SSWI driver
dt-bindings: interrupt-controller: Add T-HEAD C900 ACLINT SSWI device
irqchip/stm32mp-exti: Use of_property_present() for non-boolean properties
irqchip/mips-gic: Fix selection of GENERIC_IRQ_EFFECTIVE_AFF_MASK
irqchip/mips-gic: Prevent indirect access to clusters without CPU cores
irqchip/mips-gic: Multi-cluster support
irqchip/mips-gic: Setup defaults in each cluster
irqchip/mips-gic: Support multi-cluster in for_each_online_cpu_gic()
irqchip/mips-gic: Replace open coded online CPU iterations
genirq/irqdesc: Use str_enabled_disabled() helper in wakeup_show()
genirq/devres: Don't free interrupt which is not managed by devres
irqchip/gic-v3-its: Fix over allocation in itt_alloc_pool()
irqchip/aspeed-intc: Add AST27XX INTC support
dt-bindings: interrupt-controller: Add support for ASPEED AST27XX INTC
...
When CONFIG_DMA_ENGINE is disabled, the driver now fails to build:
drivers/tty/serial/amba-pl011.c: In function 'pl011_unthrottle_rx':
drivers/tty/serial/amba-pl011.c:1822:16: error: 'struct uart_amba_port' has no member named 'using_rx_dma'
1822 | if (uap->using_rx_dma) {
| ^~
drivers/tty/serial/amba-pl011.c:1823:20: error: 'struct uart_amba_port' has no member named 'dmacr'
1823 | uap->dmacr |= UART011_RXDMAE;
| ^~
drivers/tty/serial/amba-pl011.c:1824:32: error: 'struct uart_amba_port' has no member named 'dmacr'
1824 | pl011_write(uap->dmacr, uap, REG_DMACR);
| ^~
Add the missing #ifdef check around these field accesses, matching
what other parts of this driver do.
Fixes: 2bcacc1c87 ("serial: amba-pl011: Fix RX stall when DMA is used")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202411140617.nkjeHhsK-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20241115110021.744332-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the platform's new project uart ip upgrade,
the new project's timeout interrupt needs to use bit17
while other projects' timeout interrupt needs to use
bit13, using private data to adapt and be compatible
with all projects.
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Link: https://lore.kernel.org/r/20241113110516.2166328-2-Wenhua.Lin@unisoc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function pl011_throttle_rx() calls pl011_stop_rx() to disable RX, which
also disables the RX DMA by clearing the RXDMAE bit of the DMACR
register. However, to properly unthrottle RX when DMA is used, the
function pl011_unthrottle_rx() is expected to set the RXDMAE bit of
the DMACR register, which it currently lacks. This causes RX to stall
after the throttle API is called.
Set RXDMAE bit in the DMACR register while unthrottling RX if RX DMA is
used.
Fixes: 211565b100 ("serial: pl011: UPSTAT_AUTORTS requires .throttle/unthrottle")
Cc: stable@vger.kernel.org
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241113092629.60226-1-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The F81216E is a LPC/eSPI to 4 UART Super I/O and is mostly compatible with
the F81216H, but does not support RS-485 auto-direction delays on any port.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20241110111703.15494-1-fbrozovic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The early_console_setup() function initializes the sci_ports[0].port with
an object of type struct uart_port obtained from the object of type
struct earlycon_device received as argument by the early_console_setup().
It may happen that later, when the rest of the serial ports are probed,
the serial port that was used as earlycon (e.g., port A) to be mapped to a
different position in sci_ports[] and the slot 0 to be used by a different
serial port (e.g., port B), as follows:
sci_ports[0] = port A
sci_ports[X] = port B
In this case, the new port mapped at index zero will have associated data
that was used for earlycon.
In case this happens, after Linux boot, any access to the serial port that
maps on sci_ports[0] (port A) will block the serial port that was used as
earlycon (port B).
To fix this, add early_console_exit() that clean the sci_ports[0] at
earlycon exit time.
Fixes: 0b0cced19a ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241106120118.1719888-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the request port function by using a single call
to devm_platform_ioremap_resource().
This will also enhance the printing from /proc/iomem:
cat /proc/iomem | grep flexcom ; cat /proc/iomem | grep serial
f0004000-f00041ff : f0004000.flexcom flexcom@f0004000
f8020000-f80201ff : f8020000.flexcom flexcom@f8020000
f0004200-f00043ff : f0004200.serial serial@200
f8020200-f80203ff : f8020200.serial serial@200
fffff200-fffff3ff : fffff200.serial serial@fffff200
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Tested-by: Andrei Simion <andrei.simion@microchip.com>
Reviewed-by: Hari Prasath Gujulan Elango <hari.prasathge@microchip.com>
Link: https://lore.kernel.org/r/20241105131946.22449-1-mihai.sain@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently in omap_8250_shutdown, the dma->rx_running flag is
set to zero in omap_8250_rx_dma_flush. Next pm_runtime_get_sync
is called, which is a runtime resume call stack which can
re-set the flag. When the call omap_8250_shutdown returns, the
flag is expected to be UN-SET, but this is not the case. This
is causing issues the next time UART is re-opened and
omap_8250_rx_dma is called. Fix by moving pm_runtime_get_sync
before the omap_8250_rx_dma_flush.
cc: stable@vger.kernel.org
Fixes: 0e31c8d173 ("tty: serial: 8250_omap: add custom DMA-RX callback")
Signed-off-by: Bin Liu <b-liu@ti.com>
[Judith: Add commit message]
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20241031172315.453750-1-jm@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial driver data for Exynos8895 SoC. The main difference from
other platforms is that fifosize is only specified via the
samsung,uart-fifosize DT property.
Signed-off-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241023090902.538040-3-ivo.ivanov.ivanov1@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SG2044 relys on an internal divisor when calculating bitrate, which
means a wrong clock for the most common bitrates. So add a quirk for
this uart device to skip the set rate call and only relys on the
internal UART divisor.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Link: https://lore.kernel.org/r/20241024062105.782330-4-inochiama@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of multiple Altera JTAG UART ports available on the system, the
error message will contain information about the port for which
attaching the IRQ handler failed.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20241029130307.5003-1-tklauser@distanz.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of multiple Altera UART ports available on the system, the error
message will contain information about the port for which attaching the
IRQ handler failed.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20241029130258.4679-1-tklauser@distanz.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pcim_iomap_table() and pcim_iomap_regions_request_all() have been
deprecated by the PCI subsystem in commit e354bb84a4 ("PCI: Deprecate
pcim_iomap_table(), pcim_iomap_regions_request_all()").
Replace these functions with their successors, pcim_iomap() and
pcim_request_all_regions().
Link: https://lore.kernel.org/r/20241030112743.104395-9-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
The newly added function is used from a loadable module, so it has
to be exported the same way as the other function in this file:
ERROR: modpost: "serial_8250_warn_need_ioport" [drivers/tty/serial/8250/8250_pci.ko] undefined!
Fixes: 7c7e6c8924 ("tty: serial: handle HAS_IOPORT dependencies")
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
compile time. We thus need to add HAS_IOPORT as dependency for those
drivers using them unconditionally. Some 8250 serial drivers support
MMIO only use, so fence only the parts requiring I/O ports and print an
error message if a device can't be supported with the current
configuration.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-18-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-17-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-16-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-15-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-14-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-13-bvanassche@acm.org
Remove the old exar_ee_read() and associated helper functions.
Remove defines that are no longer needed after the switch to using the
eeprom_93cx6 driver.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/ed756c48965a95ce3384ebb7fe2441b4928b4510.1727880931.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the custom 93cx6 EEPROM read functions with the eeprom_93cx6
driver. This removes duplicate code and improves code readability.
Replace exar_ee_read() calls with eeprom_93cx6_read() or
eeprom_93cx6_multiread().
Add "select EEPROM_93CX6" to config SERIAL_8250_EXAR to ensure
eeprom_93cx6 driver is also compiled when 8250_exar driver is selected.
Note: Old exar_ee_read() and associated functions are removed in next
patch in this series.
Link to mailing list discussion with Andy Shevchenko for reference.
Link: https://lore.kernel.org/linux-serial/Ztr5u2wEt8VF1IdI@black.fi.intel.com/
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/1bf2214ae27130ca58b9e779c4d65a0e5db06fc1.1727880931.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the unnecessary "_sys" infix from the suspend PM ops.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-10-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial drivers should not be dropping characters themselves, but at
least drop the unused 'drop' parameter from the receive handler for now.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the unnecessary WARN() in case the TTY buffers are ever full in
favour of a rate limited dev_err() which doesn't kill the machine when
panic_on_warn is set.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-8-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The receiver is supposed to be enabled in the startup() callback and not
in set_termios() which is called also during console setup.
This specifically avoids accepting input before the port has been opened
(and interrupts enabled), something which can also break the GENI
firmware (cancel fails and after abort, the "stale" counter handling
appears to be broken so that later input is not processed until twelve
chars have been received).
There also does not appear to be any need to keep the receiver disabled
while updating the port settings.
Since commit 6f3c3cafb1 ("serial: qcom-geni: disable interrupts during
console writes") the calls to manipulate the secondary interrupts, which
were done without holding the port lock, can also lead to the receiver
being left disabled when set_termios() races with the console code (e.g.
when init opens the tty during boot). This can manifest itself as a
serial getty not accepting input.
The calls to stop and start rx in set_termios() can similarly race with
DMA completion and, for example, cause the DMA buffer to be unmapped
twice or the mapping to be leaked.
Fix this by only enabling the receiver during startup and while holding
the port lock to avoid racing with the console code.
Fixes: 6f3c3cafb1 ("serial: qcom-geni: disable interrupts during console writes")
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 6.3
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to wait for the DMA transfer to complete when cancelling the
rx command on stop_rx(). This specifically prevents the DMA completion
interrupt from firing after rx has been restarted, something which can
lead to an IOMMU fault and hosed rx when the interrupt handler unmaps
the DMA buffer for the new command:
qcom_geni_serial 988000.serial: serial engine reports 0 RX bytes in!
arm-smmu 15000000.iommu: FSR = 00000402 [Format=2 TF], SID=0x563
arm-smmu 15000000.iommu: FSYNR0 = 00210013 [S1CBNDX=33 WNR PLVL=3]
Bluetooth: hci0: command 0xfc00 tx timeout
Bluetooth: hci0: Reading QCA version information failed (-110)
Also add the missing state machine reset which is needed in case
cancellation fails.
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable@vger.kernel.org # 6.3
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A commit adding back the stopping of tx on port shutdown failed to add
back the locking which had also been removed by commit e83766334f
("tty: serial: qcom_geni_serial: No need to stop tx/rx on UART
shutdown").
Holding the port lock is needed to serialise against the console code,
which may update the interrupt enable register and access the port
state.
Fixes: d8aca2f968 ("tty: serial: qcom-geni-serial: stop operations in progress at shutdown")
Fixes: 947cc4ecc0 ("serial: qcom-geni: fix soft lockup on sw flow control and suspend")
Cc: stable@vger.kernel.org # 6.3
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 35781d8356.
Hibernation is not supported on Qualcomm platforms with mainline
kernels yet a broken vendor implementation for the GENI serial driver
made it upstream.
This is effectively dead code that cannot be tested and should just be
removed, but if these paths were ever hit for an open non-console port
they would crash the machine as the driver would fail to enable clocks
during restore() (i.e. all ports would have to be closed by drivers and
user space before hibernating the system to avoid this as a comment in
the code hinted at).
The broken implementation also added a random call to enable the
receiver in the port setup code where it does not belong and which
enables the receiver prematurely for console ports.
Fixes: 35781d8356 ("tty: serial: qcom-geni-serial: Add support for Hibernation feature")
Cc: stable@vger.kernel.org # 6.2
Cc: Aniket Randive <quic_arandive@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The polled console (KGDB/KDB) implementation must not call port setup
unconditionally as the port may already be in use by the console or a
getty.
Only make sure that the receiver is enabled, but do not enable any
device interrupts.
Fixes: d8851a96ba ("tty: serial: qcom-geni-serial: Add a poll_init() function")
Cc: stable@vger.kernel.org # 6.4
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sending data using DMA at high baudrate (4 Mbdps in local test case) to
a device with small RX buffer which keeps asserting RTS after every received
byte, it is possible that the iMX UART driver would not recognize the falling
edge of RTS input signal and get stuck, unable to transmit any more data.
This condition happens when the following sequence of events occur:
- imx_uart_mctrl_check() is called at some point and takes a snapshot of UART
control signal status into sport->old_status using imx_uart_get_hwmctrl().
The RTSS/TIOCM_CTS bit is of interest here (*).
- DMA transfer occurs, the remote device asserts RTS signal after each byte.
The i.MX UART driver recognizes each such RTS signal change, raises an
interrupt with USR1 register RTSD bit set, which leads to invocation of
__imx_uart_rtsint(), which calls uart_handle_cts_change().
- If the RTS signal is deasserted, uart_handle_cts_change() clears
port->hw_stopped and unblocks the port for further data transfers.
- If the RTS is asserted, uart_handle_cts_change() sets port->hw_stopped
and blocks the port for further data transfers. This may occur as the
last interrupt of a transfer, which means port->hw_stopped remains set
and the port remains blocked (**).
- Any further data transfer attempts will trigger imx_uart_mctrl_check(),
which will read current status of UART control signals by calling
imx_uart_get_hwmctrl() (***) and compare it with sport->old_status .
- If current status differs from sport->old_status for RTS signal,
uart_handle_cts_change() is called and possibly unblocks the port
by clearing port->hw_stopped .
- If current status does not differ from sport->old_status for RTS
signal, no action occurs. This may occur in case prior snapshot (*)
was taken before any transfer so the RTS is deasserted, current
snapshot (***) was taken after a transfer and therefore RTS is
deasserted again, which means current status and sport->old_status
are identical. In case (**) triggered when RTS got asserted, and
made port->hw_stopped set, the port->hw_stopped will remain set
because no change on RTS line is recognized by this driver and
uart_handle_cts_change() is not called from here to unblock the
port->hw_stopped.
Update sport->old_status in __imx_uart_rtsint() accordingly to make
imx_uart_mctrl_check() detect such RTS change. Note that TIOCM_CAR
and TIOCM_RI bits in sport->old_status do not suffer from this problem.
Fixes: ceca629e0b ("[ARM] 2971/1: i.MX uart handle rts irq")
Cc: stable <stable@kernel.org>
Reviewed-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20241002184133.19427-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implements the necessary callbacks to switch the imx console driver to
perform as an nbcon console.
Add implementations for the nbcon consoles (write_atomic, write_thread,
driver_enter, driver_exit) and add CON_NBCON to the initial flags.
The legacy code is kept in order to easily switch back to legacy mode
by defining CONFIG_SERIAL_IMX_LEGACY_CONSOLE.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Link: https://lore.kernel.org/r/20240913-serial-imx-nbcon-v3-1-4c627302335b@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx7ulp/imx8ulp/imx8qxp lpuart IP support 7-bits format and have no
limitation on parity when CS7. Remove this limitation and add 7-bits
format support on imx7ulp/imx8ulp/imx8qxp.
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Link: https://lore.kernel.org/r/20241008094418.439706-1-ziniu.wang_1@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When specifying flag SER_RS485_RTS_ON_SEND in RS485 configuration,
we get the following warning after commit 4afeced55b ("serial: core:
fix sanitizing check for RTS settings"):
invalid RTS setting, using RTS_AFTER_SEND instead
This results in SER_RS485_RTS_AFTER_SEND being set and the
driver always write to the register field SC16IS7XX_EFCR_RTS_INVERT_BIT,
which breaks some hardware using these chips.
The hardware supports both RTS_ON_SEND and RTS_AFTER_SEND modes, so fix
this by announcing support for RTS_ON_SEND.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Suggested-by: Konstantin Pugin <ria.freelander@gmail.com>
Link: https://lore.kernel.org/lkml/20240422133219.2710061-2-ria.freelander@gmail.com
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Tested-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20241007162716.3122912-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes several typos in the comments within the tty/8250
directory to improve readability and code documentation.
Detected using codespell.
Signed-off-by: Yu Jiaoliang <yujiaoliang@vivo.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240929100931.530620-1-yujiaoliang@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not obvious from the first glance that the list of the CTI EEPROM
offsets covers three different models, let's group them accordingly for
better readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240920154430.3323820-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Comments regarding status of port.lock on internal functions is useful when
reviewing correct handling of registers that must be protected by this
lock.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Link: https://lore.kernel.org/r/20240913-serial-imx-lockfix-v1-2-4d102746c89d@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/tty/serial to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241007205803.444994-7-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Today we are proxying the `console=` command line args to the
`param_setup_earlycon()` handler. This is done because the following are
equivalent:
console=uart[8250],mmio,<addr>[,options]
earlycon=uart[8250],mmio,<addr>[,options]
Both invocations enable an early `bootconsole`. `console=uartXXXX` is
just an alias for `earlycon=uartXXXX`.
In addition, when `earlycon=` (empty value) or just `earlycon`
(no value) is specified on the command line, we enable the earlycon
`bootconsole` specified by the SPCR table or the DT.
The problem arises when `console=` (empty value) is specified on the
command line. It's intention is to disable the `console`, but what
happens instead is that the SPRC/DT console gets enabled.
This happens because we are proxying the `console=` (empty value)
parameter to the `earlycon` handler. The `earlycon` handler then sees
that the parameter value is empty, so it enables the SPCR/DT
`bootconsole`.
This change makes it so that the `console` or `console=` parameters no
longer enable the SPCR/DT `bootconsole`. I also cleans up the hack in
`main.c` that would forward the `console` parameter to the `earlycon`
handler.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Tested-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20240911123507.v2.1.Id08823b2f848237ae90ce5c5fa7e027e97c33ad3@changeid
Signed-off-by: Petr Mladek <pmladek@suse.com>
Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup of
the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART engine
that that chip seems to have. Hopefully it's in a better state now,
but hardware designers still seem to come up with more ways to make
broken UARTS 40+ years after this all should have finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZvUz1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymAhwCcCw/6BX3aKGTyx7ZxeMRc/mjbSLIAoMUv6bGT
6H04ZvcSd63ZotAWeZsn
=PWB8
-----END PGP SIGNATURE-----
Merge tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup
of the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART
engine that that chip seems to have. Hopefully it's in a better
state now, but hardware designers still seem to come up with more
ways to make broken UARTS 40+ years after this all should have
finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems"
* tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: samsung: Fix serial rx on Apple A7-A9
tty: serial: samsung: Fix A7-A11 serial earlycon SError
tty: serial: samsung: Use bit manipulation macros for APPLE_S5L_*
tty: rp2: Fix reset with non forgiving PCIe host bridges
serial: 8250_aspeed_vuart: Enable module autoloading
serial: qcom-geni: fix polled console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix console corruption
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix fifo polling timeout
tty: hvc: convert comma to semicolon
mxser: convert comma to semicolon
serial: 8250_bcm2835aux: Fix clock imbalance in PM resume
serial: sc16is7xx: convert bitmask definitions to use BIT() macro
serial: sc16is7xx: fix copy-paste errors in EFR_SWFLOWx_BIT constants
serial: sc16is7xx: remove SC16IS7XX_MSR_DELTA_MASK
serial: xilinx_uartps: Make cdns_rs485_supported static
...
Apple's older A7-A9 SoCs seems to use bit 3 in UTRSTAT as RXTO, which is
enabled by bit 11 in UCON.
Access these bits in addition to the original RXTO and RXTO enable bits,
to allow serial rx to function on A7-A9 SoCs. This change does not
appear to affect the A10 SoC and up.
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Nick Chan <towinchenmi@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20240911050741.14477-4-towinchenmi@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apple's earlier SoCs, like A7-A11, requires 32-bit writes for the serial
port. Otherwise, a SError happens when writing to UTXH (+0x20). This only
manifested in earlycon as reg-io-width in the device tree is consulted
for normal serial writes.
Change the iotype of the port to UPIO_MEM32, to allow the serial port to
function on A7-A11 SoCs. This change does not appear to affect Apple M1 and
above.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Tested-by: Janne Grunau <j@jannau.net>
Signed-off-by: Nick Chan <towinchenmi@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20240911050741.14477-3-towinchenmi@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write to RP2_GLOBAL_CMD followed by an immediate read of
RP2_GLOBAL_CMD in rp2_reset_asic() is intented to flush out the write,
however by then the device is already in reset and cannot respond to a
memory cycle access.
On platforms such as the Raspberry Pi 4 and others using the
pcie-brcmstb.c driver, any memory access to a device that cannot respond
is met with a fatal system error, rather than being substituted with all
1s as is usually the case on PC platforms.
Swapping the delay and the read ensures that the device has finished
resetting before we attempt to read from it.
Fixes: 7d9f49afa4 ("serial: rp2: New driver for Comtrol RocketPort 2 cards")
Cc: stable <stable@kernel.org>
Suggested-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240906225435.707837-1-florian.fainelli@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240903131503.961178-1-liaochen4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The polled UART operations are used by the kernel debugger (KDB, KGDB),
which can interrupt the kernel at any point in time. The current
Qualcomm GENI implementation does not really work when there is on-going
serial output as it inadvertently "hijacks" the current tx command,
which can result in both the initial debugger output being corrupted as
well as the corruption of any on-going serial output (up to 4k
characters) when execution resumes:
0190: abcdefghijklmnopqrstuvwxyz0123456789 0190: abcdefghijklmnopqrstuvwxyz0123456789
0191: abcdefghijklmnop[ 50.825552] sysrq: DEBUG
qrstuvwxyz0123456789 0191: abcdefghijklmnopqrstuvwxyz0123456789
Entering kdb (current=0xffff53510b4cd280, pid 640) on processor 2 due to Keyboard Entry
[2]kdb> go
omlji3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t72r2rp
o9n976k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawavu:t7t8s8s8r2r2q0q0p
o9n9n8ml6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav v u:u:t9t0s4s4rq0p
o9n9n8m8m7l7l6k6k5j5j40q0p p o
o9n9n8m8m7l7l6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t8t9s4s4r4r4q0q0p
Fix this by making sure that the polled output implementation waits for
the tx fifo to drain before cancelling any on-going longer transfers. As
the polled code cannot take any locks, leave the state variables as they
are and instead make sure that the interrupt handler always starts a new
tx command when there is data in the write buffer.
Since the debugger can interrupt the interrupt handler when it is
writing data to the tx fifo, it is currently not possible to fully
prevent losing up to 64 bytes of tty output on resume.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 4.17
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable the GENI interrupts during console writes to reduce the risk of
having interrupt handlers spinning on the port lock on other cores for
extended periods of time.
This can, for example, reduce the total amount of time spent in the
interrupt handler during boot of the x1e80100 CRD by up to a factor nine
(e.g. from 274 ms to 30 ms) while the worst case processing time drops
from 19 ms to 8 ms.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-8-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm serial console implementation is broken and can lose
characters when the serial port is also used for tty output.
Specifically, the console code only waits for the current tx command to
complete when all data has already been written to the fifo. When there
are on-going longer transfers this often means that console output is
lost when the console code inadvertently "hijacks" the current tx
command instead of starting a new one.
This can, for example, be observed during boot when console output that
should have been interspersed with init output is truncated:
[ 9.462317] qcom-snps-eusb2-hsphy fde000.phy: Registered Qcom-eUSB2 phy
[ OK ] Found device KBG50ZNS256G KIOXIA Wi[ 9.471743ndows.
[ 9.539915] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
Add a new state variable to track how much data has been written to the
fifo and use it to determine when the fifo and shift register are both
empty. This is needed since there is currently no other known way to
determine when the shift register is empty.
This in turn allows the console code to interrupt long transfers without
losing data.
Note that the oops-in-progress case is similarly broken as it does not
cancel any active command and also waits for the wrong status flag when
attempting to drain the fifo (TX_FIFO_NOT_EMPTY_EN is only set when
cancelling a command leaves data in the fifo).
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Fixes: a1fee899e5 ("tty: serial: qcom_geni_serial: Fix softlock")
Fixes: 9e957a1550 ("serial: qcom-geni: Don't cancel/abort if we can't get the port lock")
Cc: stable@vger.kernel.org # 4.17
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-7-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a small modification the qcom_geni_serial_poll_bit() function
could be used to poll more than just a single bit. Let's generalize
it. We'll make the qcom_geni_serial_poll_bit() into just a wrapper of
the general function.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240610152420.v4.5.Ic6411eab8d9d37acc451705f583fb535cd6dadb2@changeid
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "offset" passed in should be unsigned since it's always a positive
offset from our memory mapped IO.
The "field" should be u32 since we're anding it with a 32-bit value
read from the device.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240610152420.v4.4.I24a0de52dd7336908df180fa6b698e001f3aff82@changeid
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 663abb1a7a ("tty: serial: qcom_geni_serial: Fix UART hang")
addressed an issue with stalled tx after the console code interrupted
the last bytes of a tx command by reenabling the watermark interrupt if
there is data in write buffer. This can however break software flow
control by re-enabling tx after the user has stopped it.
Address the original issue by not clearing the CMD_DONE flag after
polling for command completion. This allows the interrupt handler to
start another transfer when the CMD_DONE interrupt has not been disabled
due to flow control.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Fixes: 663abb1a7a ("tty: serial: qcom_geni_serial: Fix UART hang")
Cc: stable@vger.kernel.org # 4.17
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The qcom_geni_serial_poll_bit() can be used to wait for events like
command completion and is supposed to wait for the time it takes to
clear a full fifo before timing out.
As noted by Doug, the current implementation does not account for start,
stop and parity bits when determining the timeout. The helper also does
not currently account for the shift register and the two-word
intermediate transfer register.
A too short timeout can specifically lead to lost characters when
waiting for a transfer to complete as the transfer is cancelled on
timeout.
Instead of determining the poll timeout on every call, store the fifo
timeout when updating it in set_termios() and make sure to take the
shift and intermediate registers into account. Note that serial core has
already added a 20 ms margin to the fifo timeout.
Also note that the current uart_fifo_timeout() interface does
unnecessary calculations on every call and did not exist in earlier
kernels so only store its result once. This facilitates backports too as
earlier kernels can derive the timeout from uport->timeout, which has
since been removed.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 4.17
Reported-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that bit definition comments were cleaned up, convert bitmask
definitions to use BIT() macro for clarity.
Convert SC16IS7XX_IIR_ID_MASK to use GENMASK() macro -
- while at that, realign comments.
Compose SC16IS7XX_LSR_BRK_ERROR_MASK using aforementioned constants,
instead of open-coding it, and remove now unneeded comments.
Signed-off-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/8b45a01e-7cc5-4d53-b467-c6680bc51ef4@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Comments attached to bits 0 and 1 incorrectly referenced bits 2 and 3,
which don't match the datasheet - fix them.
At the same time remove comments for individual constants, as they add
nothing to the definitions themselves.
Signed-off-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/2986a485-935d-4ab2-9a16-4a85288aa15a@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sparse tool complains as follows:
drivers/tty/serial/xilinx_uartps.c:222:21: warning:
symbol 'cdns_rs485_supported' was not declared. Should it be static?
This symbol is not used outside xilinx_uartps.c, so marks it static.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20240819120107.3884973-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce uart_port_set_cons() as a wrapper to set @cons of a
uart_port. The wrapper sets @cons under the port lock in order
to prevent @cons from disappearing while another context is
holding the port lock. This is necessary for a follow-up
commit relating to the port lock wrappers, which rely on @cons
not changing between lock and unlock.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Tested-by: Théo Lebrun <theo.lebrun@bootlin.com> # EyeQ5, AMBA-PL011
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240820063001.36405-12-john.ogness@linutronix.de
Signed-off-by: Petr Mladek <pmladek@suse.com>
This reverts commit 68e6939ea9.
Kevin reported that this causes a crash during suspend on platforms that
dont use PM domains.
Link: https://lore.kernel.org/r/7ha5hgpchq.fsf@baylibre.com
Cc: Thomas Richard <thomas.richard@bootlin.com>
Fixes: 68e6939ea9 ("serial: 8250_omap: Set the console genpd always on if no console suspend")
Cc: stable <stable@kernel.org>
Reported-by: Kevin Hilman <khilman@kernel.org>
Signed-off-by: Griffin Kroah-Hartman <griffin@kroah.com>
Link: https://lore.kernel.org/r/20240814111747.82371-1-griffin@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guards can help to make the code more readable. So use it wherever they
do so.
On many places labels and 'ret' locals are eliminated completely.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240808103549.429349-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definition of the PM operations opens code the existing macro,
replace it with the DEFINE_SIMPLE_DEV_PM_OPS() for setting the driver's
PM routines.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240813081954.1408792-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify comment style and fix indentation in some cases.
While at it, add that it supports ACPI enumerated non-PNP devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240812154901.1068407-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it clear that it supports two cases, pure platform device and ACPI.
With this in mind, split serial8250_probe() to two functions and rename
the ACPI case accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240812154901.1068407-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tidy up ACPI ID table:
- remove explicit driver_data initializer
- drop comma in the terminator entry
- use C comment style
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240812154901.1068407-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UPF_IOREMAP is for serial core to map the resource on behalf of the
driver. No need to perform this explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240812154901.1068407-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the wakeup-source property is present, enable wakeup from this
device.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20240807141227.1093006-6-msp@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver sets wakeup enable by default. But not all UARTs are meant to
be wakeup enabled. Change the default to be wakeup capable but not
enabled. The user can enable wakeup when needed.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20240807141227.1093006-5-msp@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If devm_request_irq fails, the code does not cleanup many things that
were setup before. Instead of directly returning ret we should jump to
err.
Fixes: fef4f60031 ("serial: 8250: omap: Fix life cycle issues for interrupt handlers")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20240807141227.1093006-4-msp@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This field seems to be unused for quite some time already. Remove it.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20240807141227.1093006-3-msp@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt handler routines and helpers are casting the 'void *'
pointer to 'struct exynos_uart_port *' all over the place.
There is no need for that, we can do the casting once and keep passing
the 'struct exynos_uart_port *', simplifying the code and saving a few
lines of code.
No functional changes.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240808-samsung-tty-cleanup-v3-2-494412f49f4b@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'irq' argument is not used in any of the callees, we can just drop
it and simplify the code.
No functional changes.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240808-samsung-tty-cleanup-v3-1-494412f49f4b@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In RS485 mode, the RTS pin is driven high by hardware when the transmitter
is operating. This behaviour cannot be changed. This means that the driver
should claim that it supports SER_RS485_RTS_ON_SEND and not
SER_RS485_RTS_AFTER_SEND.
Otherwise, when configuring the port with the SER_RS485_RTS_ON_SEND, one
get the following warning:
kern.warning kernel: atmel_usart_serial atmel_usart_serial.2.auto:
ttyS1 (1): invalid RTS setting, using RTS_AFTER_SEND instead
which is contradictory with what's really happening.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Cc: stable <stable@kernel.org>
Tested-by: Alexander Dahl <ada@thorsis.com>
Fixes: af47c491e3 ("serial: atmel: Fill in rs485_supported")
Link: https://lore.kernel.org/r/20240808060637.19886-1-othacehe@gnu.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With "earlycon initcall_debug=1 loglevel=8" in bootargs, kernel
sometimes boot hang. It is because normal console still is not ready,
but runtime suspend is called, so early console putchar will hang
in waiting TRDE set in UARTSTAT.
The lpuart driver has auto suspend delay set to 3000ms, but during
uart_add_one_port, a child device serial ctrl will added and probed with
its pm runtime enabled(see serial_ctrl.c).
The runtime suspend call path is:
device_add
|-> bus_probe_device
|->device_initial_probe
|->__device_attach
|-> pm_runtime_get_sync(dev->parent);
|-> pm_request_idle(dev);
|-> pm_runtime_put(dev->parent);
So in the end, before normal console ready, the lpuart get runtime
suspended. And earlycon putchar will hang.
To address the issue, mark last busy just after pm_runtime_enable,
three seconds is long enough to switch from bootconsole to normal
console.
Fixes: 43543e6f53 ("tty: serial: fsl_lpuart: Add runtime pm support")
Cc: stable <stable@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20240808140325.580105-1-peng.fan@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
quot_frac is unused in serial8250_do_set_divisor() since commit
b2b4b8ed3c (serial: 8250_exar: Move custom divisor support out from
8250_port). So no point to pass it.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240805102046.307511-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coverity reports (as CID 1536978) that uart_poll_init() passes
uninitialized pm_state to uart_change_pm(). It is in case the first 'if'
takes the true branch (does "goto out;").
Fix this and simplify the function by simple guard(mutex). The code
needs no labels after this at all. And it is pretty clear that the code
has not fiddled with pm_state at that point.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Fixes: 5e227ef2aa (serial: uart_poll_init() should power on the UART)
Cc: stable@vger.kernel.org
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240805102046.307511-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit af224ca2df (serial: core: Prevent unsafe uart port access, part
3) added few uport == NULL checks. It added one to uart_shutdown(), so
the commit assumes, uport can be NULL in there. But right after that
protection, there is an unprotected "uart_port_dtr_rts(uport, false);"
call. That is invoked only if HUPCL is set, so I assume that is the
reason why we do not see lots of these reports.
Or it cannot be NULL at this point at all for some reason :P.
Until the above is investigated, stay on the safe side and move this
dereference to the if too.
I got this inconsistency from Coverity under CID 1585130. Thanks.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240805102046.307511-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first element in uart_8250_port is a structure, so initializing
it to 0 causes a warning on newer compilers:
drivers/tty/serial/8250/8250_platform.c: In function 'serial8250_platform_probe':
drivers/tty/serial/8250/8250_platform.c:111:40: error: excess elements in struct initializer [-Werror]
111 | struct uart_8250_port uart = { 0 };
Use the modern empty {} initializer instead that works on all
supported compilers.
Fixes: d9e5a0ce2f ("serial: 8250_platform: Enable generic 16550A platform devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20240807075751.2206508-2-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The acpi_platform_serial_table[] array is defined globally without
an #ifdef check for CONFIG_ACPI, so ACPI_PTR() makes no sense
here:
drivers/tty/serial/8250/8250_platform.c:271:36: error: 'acpi_platform_serial_table' defined but not used [-Werror=unused-const-variable=]
271 | static const struct acpi_device_id acpi_platform_serial_table[] = {
Fixes: d9e5a0ce2f ("serial: 8250_platform: Enable generic 16550A platform devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Link: https://lore.kernel.org/r/20240807075751.2206508-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, 8250_platform driver is used only for devices with fixed
serial ports (plat_serial8250_port). Extend this driver for any generic
16550A platform devices which can be probed using standard hardware
discovery mechanisms like ACPI.
This is required in particular for RISC-V which has non-PNP generic
16550A compatible UART that needs to be enumerated as ACPI platform
device.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Link: https://lore.kernel.org/r/20240730051218.767580-1-sunilvl@ventanamicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds suspend/resume support for the 8250_bcm2835aux
driver to provide power management support on attached
devices.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20240728130029.78279-7-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 3a50365d8c ("serial: 8250: Add OF support for Xscale
variant"), 8250_of can support the xscale variant. Now, let's add
the earlycon support for xscale too.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20240711160720.3488-3-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two other drivers that bind to "mrvl,mmp-uart": the 8250_of
and the 8250_pxa. The previous one is generic and the latter is binded
to ARCH_PXA || ARCH_MMP. Now we may have pxa programming compatible
HW to support, making use of the generic 8250_of seems a good idea.
However, there's no earlycon support if we go with this solution. So
move the mmp|pxa-uart earlycon code to core 8250_early.c.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20240711160720.3488-2-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously 8250_dma used a circular xmit->buf as DMA output buffer. This
causes messages that wrap around in the circular buffer to be
transmitted using 2 DMA transfers. Depending on baud rate and processor
load this can cause an interchar gap in the middle of the message. On
the receiving end the gap may cause a short receive timeout, possibly
long enough to terminate a DMA transfer, but too short to restart a
receive DMA transfer in time thus causing a receive buffer overrun.
This is especially a problem for devices with high speed UARTs (HSU)
where even deep 64 byte FIFO's are not sufficient to handle interrupt
latency.
The circular buffer has now been replaced by kfifo which requires a SG
list with a single entry, which still causes 2 dma transfers when a wrap
around occurs. Fix this by allowing up to 2 entries in the sgl.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240716214055.102269-1-ftoth@exalondelft.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based kernel configuration guards.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Link: https://lore.kernel.org/r/20240716180010.126987-1-rgallaispou@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When enabling access to the special register set, Receiver time-out and
RHR interrupts can happen. In this case, the IRQ handler will try to read
from the FIFO thru the RHR register at address 0x00, but address 0x00 is
mapped to DLL register, resulting in erroneous FIFO reading.
Call graph example:
sc16is7xx_startup(): entry
sc16is7xx_ms_proc(): entry
sc16is7xx_set_termios(): entry
sc16is7xx_set_baud(): DLH/DLL = $009C --> access special register set
sc16is7xx_port_irq() entry --> IIR is 0x0C
sc16is7xx_handle_rx() entry
sc16is7xx_fifo_read(): --> unable to access FIFO (RHR) because it is
mapped to DLL (LCR=LCR_CONF_MODE_A)
sc16is7xx_set_baud(): exit --> Restore access to general register set
Fix the problem by claiming the efr_lock mutex when accessing the Special
register set.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240723125302.1305372-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes, when a packet is received on channel A at almost the same time
as a packet is about to be transmitted on channel B, we observe with a
logic analyzer that the received packet on channel A is transmitted on
channel B. In other words, the Tx buffer data on channel B is corrupted
with data from channel A.
The problem appeared since commit 4409df5866 ("serial: sc16is7xx: change
EFR lock to operate on each channels"), which changed the EFR locking to
operate on each channel instead of chip-wise.
This commit has introduced a regression, because the EFR lock is used not
only to protect the EFR registers access, but also, in a very obscure and
undocumented way, to protect access to the data buffer, which is shared by
the Tx and Rx handlers, but also by each channel of the IC.
Fix this regression first by switching to kfifo_out_linear_ptr() in
sc16is7xx_handle_tx() to eliminate the need for a shared Rx/Tx buffer.
Secondly, replace the chip-wise Rx buffer with a separate Rx buffer for
each channel.
Fixes: 4409df5866 ("serial: sc16is7xx: change EFR lock to operate on each channels")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240723125302.1305372-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling ioctl TIOCSSERIAL with an invalid baud_base can
result in uartclk being zero, which will result in a
divide by zero error in uart_get_divisor(). The check for
uartclk being zero in uart_set_info() needs to be done
before other settings are made as subsequent calls to
ioctl TIOCSSERIAL for the same port would be impacted if
the uartclk check was done where uartclk gets set.
Oops: divide error: 0000 PREEMPT SMP KASAN PTI
RIP: 0010:uart_get_divisor (drivers/tty/serial/serial_core.c:580)
Call Trace:
<TASK>
serial8250_get_divisor (drivers/tty/serial/8250/8250_port.c:2576
drivers/tty/serial/8250/8250_port.c:2589)
serial8250_do_set_termios (drivers/tty/serial/8250/8250_port.c:502
drivers/tty/serial/8250/8250_port.c:2741)
serial8250_set_termios (drivers/tty/serial/8250/8250_port.c:2862)
uart_change_line_settings (./include/linux/spinlock.h:376
./include/linux/serial_core.h:608 drivers/tty/serial/serial_core.c:222)
uart_port_startup (drivers/tty/serial/serial_core.c:342)
uart_startup (drivers/tty/serial/serial_core.c:368)
uart_set_info (drivers/tty/serial/serial_core.c:1034)
uart_set_info_user (drivers/tty/serial/serial_core.c:1059)
tty_set_serial (drivers/tty/tty_io.c:2637)
tty_ioctl (drivers/tty/tty_io.c:2647 drivers/tty/tty_io.c:2791)
__x64_sys_ioctl (fs/ioctl.c:52 fs/ioctl.c:907
fs/ioctl.c:893 fs/ioctl.c:893)
do_syscall_64 (arch/x86/entry/common.c:52
(discriminator 1) arch/x86/entry/common.c:83 (discriminator 1))
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
Reported-by: syzkaller <syzkaller@googlegroups.com>
Cc: stable@vger.kernel.org
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Rule: add
Link: https://lore.kernel.org/stable/1721148848-9784-1-git-send-email-george.kennedy%40oracle.com
Link: https://lore.kernel.org/r/1721219078-3209-1-git-send-email-george.kennedy@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases to
get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions. It's not all that useful for a "write a whole driver
in rust" type of thing, but the firmware bindings do help out the
phy rust drivers, and the driver core bindings give a solid base on
which others can start their work. There is still a long way to go
here before we have a multitude of rust drivers being added, but
it's a great first step.
- driver core const api changes. This reached across all bus types,
and there are some fix-ups for some not-common bus types that
linux-next and 0-day testing shook out. This work is being done to
help make the rust bindings more safe, as well as the C code, moving
toward the end-goal of allowing us to put driver structures into
read-only memory. We aren't there yet, but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZqH+aQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoOQCfVBdLcBjEDAGh3L8qHRGMPy4rV2EAoL/r+zKm
cJEYtJpGtWX6aAtugm9E
=ZyJV
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases
to get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions.
It's not all that useful for a "write a whole driver in rust" type
of thing, but the firmware bindings do help out the phy rust
drivers, and the driver core bindings give a solid base on which
others can start their work.
There is still a long way to go here before we have a multitude of
rust drivers being added, but it's a great first step.
- driver core const api changes.
This reached across all bus types, and there are some fix-ups for
some not-common bus types that linux-next and 0-day testing shook
out.
This work is being done to help make the rust bindings more safe,
as well as the C code, moving toward the end-goal of allowing us to
put driver structures into read-only memory. We aren't there yet,
but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
ARM: sa1100: make match function take a const pointer
sysfs/cpu: Make crash_hotplug attribute world-readable
dio: Have dio_bus_match() callback take a const *
zorro: make match function take a const pointer
driver core: module: make module_[add|remove]_driver take a const *
driver core: make driver_find_device() take a const *
driver core: make driver_[create|remove]_file take a const *
firmware_loader: fix soundness issue in `request_internal`
firmware_loader: annotate doctests as `no_run`
devres: Correct code style for functions that return a pointer type
devres: Initialize an uninitialized struct member
devres: Fix memory leakage caused by driver API devm_free_percpu()
devres: Fix devm_krealloc() wasting memory
driver core: platform: Switch to use kmemdup_array()
driver core: have match() callback in struct bus_type take a const *
MAINTAINERS: add Rust device abstractions to DRIVER CORE
device: rust: improve safety comments
MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer
MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER
firmware: rust: improve safety comments
...
Here is a small set of tty and serial driver updates for 6.11-rc1. Not
much happened this cycle, unlike the previous kernel release which had
lots of "excitement" in this part of the kernel. Included in here are
the following changes:
- dt binding updates for new platforms
- 8250 driver updates
- various small serial driver fixes and updates
- printk/console naming and matching attempt #2 (was reverted for
6.10-final, should be good to go this time around, acked by the
relevant maintainers).
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZppbCQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymV1ACeIY5kgipqY7w4d3/7PcpKMiftrisAn0hr6csj
Gan+k3cuVGlasGkaQ5/B
=35VK
-----END PGP SIGNATURE-----
Merge tag 'tty-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is a small set of tty and serial driver updates for 6.11-rc1. Not
much happened this cycle, unlike the previous kernel release which had
lots of "excitement" in this part of the kernel. Included in here are
the following changes:
- dt binding updates for new platforms
- 8250 driver updates
- various small serial driver fixes and updates
- printk/console naming and matching attempt #2 (was reverted for
6.10-final, should be good to go this time around, acked by the
relevant maintainers).
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (22 commits)
Documentation: kernel-parameters: Add DEVNAME:0.0 format for serial ports
serial: core: Add serial_base_match_and_update_preferred_console()
printk: Add match_devname_and_update_preferred_console()
serial: sc16is7xx: hardware reset chip if reset-gpios is defined in DT
dt-bindings: serial: sc16is7xx: add reset-gpios
dt-bindings: serial: vt8500-uart: convert to json-schema
serial: 8250_platform: Explicitly show we initialise ISA ports only once
tty: add missing MODULE_DESCRIPTION() macros
dt-bindings: serial: mediatek,uart: add MT7988
serial: sh-sci: Add support for RZ/V2H(P) SoC
dt-bindings: serial: Add documentation for Renesas RZ/V2H(P) (R9A09G057) SCIF support
dt-bindings: serial: renesas,scif: Make 'interrupt-names' property as required
dt-bindings: serial: renesas,scif: Validate 'interrupts' and 'interrupt-names'
dt-bindings: serial: renesas,scif: Move ref for serial.yaml at the end
riscv: dts: starfive: jh7110: Add the core reset and jh7110 compatible for uarts
serial: 8250_dw: Use reset array API to get resets
dt-bindings: serial: snps-dw-apb-uart: Add one more reset signal for StarFive JH7110 SoC
serial: 8250: Extract platform driver
serial: 8250: Extract RSA bits
serial: imx: stop casting struct uart_port to struct imx_port
...
Let's add serial_base_match_and_update_preferred_console() for consoles
using DEVNAME:0.0 style naming.
The earlier approach to add it caused issues in the kernel command line
ordering as we were calling __add_preferred_console() again for the
deferred consoles.
Signed-off-by: Tony Lindgren <tony.lindgren@linux.intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Tested-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20240703100615.118762-3-tony.lindgren@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm GENI serial driver did not handle buffer flushing and used
to print discarded characters when the circular buffer was cleared.
Since commit 1788cf6a91 ("tty: serial: switch from circ_buf to kfifo")
this instead resulted in a hard lockup due to
qcom_geni_serial_send_chunk_fifo() spinning indefinitely in the
interrupt handler.
The underlying bugs have now been fixed, but make sure to output NUL
characters instead of killing the machine if a similar driver bug is
ever reintroduced.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240704101805.30612-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm GENI serial driver does not handle buffer flushing and used
to continue printing discarded characters when the circular buffer was
cleared. Since commit 1788cf6a91 ("tty: serial: switch from circ_buf
to kfifo") this instead results in a hard lockup due to
qcom_geni_serial_send_chunk_fifo() spinning indefinitely in the
interrupt handler.
This is easily triggered by interrupting a command such as dmesg in a
serial console but can also happen when stopping a serial getty on
reboot.
Implement the flush_buffer() callback and use it to cancel any active TX
command when the write buffer has been emptied.
Reported-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/lkml/20240610222515.3023730-1-dianders@chromium.org/
Fixes: 1788cf6a91 ("tty: serial: switch from circ_buf to kfifo")
Fixes: a1fee899e5 ("tty: serial: qcom_geni_serial: Fix softlock")
Cc: stable@vger.kernel.org # 5.0
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240704101805.30612-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stop_tx() callback is used to implement software flow control and
must not discard data as the Qualcomm GENI driver is currently doing
when there is an active TX command.
Cancelling an active command can also leave data in the hardware FIFO,
which prevents the watermark interrupt from being enabled when TX is
later restarted. This results in a soft lockup and is easily triggered
by stopping TX using software flow control in a serial console but this
can also happen after suspend.
Fix this by only stopping any active command, and effectively clearing
the hardware fifo, when shutting down the port. When TX is later
restarted, a transfer command may need to be issued to discard any stale
data that could prevent the watermark interrupt from firing.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 4.17
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240704101805.30612-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a process is killed while writing to a /dev/ttymxc* device in RS485
mode, we observe that the RTS signal is left high, thus making it
impossible for other devices to transmit anything.
Moreover, the ->tx_state variable is left in state SEND, which means
that when one next opens the device and configures baud rate etc., the
initialization code in imx_uart_set_termios dutifully ensures the RTS
pin is pulled down, but since ->tx_state is already SEND, the logic in
imx_uart_start_tx() does not in fact pull the pin high before
transmitting, so nothing actually gets on the wire on the other side
of the transceiver. Only when that transmission is allowed to complete
is the state machine then back in a consistent state.
This is completely reproducible by doing something as simple as
seq 10000 > /dev/ttymxc0
and hitting ctrl-C, and watching with a logic analyzer.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: stable <stable@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240625184206.508837-1-linux@rasmusvillemoes.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Errata i2310[0] says, Erroneous timeout can be triggered,
if this Erroneous interrupt is not cleared then it may leads
to storm of interrupts.
Commit 9d141c1e61 ("serial: 8250_omap: Implementation of Errata i2310")
which added the workaround but missed ensuring RX FIFO is really empty
before applying the errata workaround as recommended in the errata text.
Fix this by adding back check for UART_OMAP_RX_LVL to be 0 for
workaround to take effect.
[0] https://www.ti.com/lit/pdf/sprz536 page 23
Fixes: 9d141c1e61 ("serial: 8250_omap: Implementation of Errata i2310")
Cc: stable@vger.kernel.org
Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
Closes: https://lore.kernel.org/all/e96d0c55-0b12-4cbf-9d23-48963543de49@ti.com/
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240625160725.2102194-1-u-kumar1@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit a81dbd0463 ("serial: imx: set receiver level before
starting uart") we set the receiver level to its default value. This
caused a regression when using SDMA, where the receiver level is 9
instead of 8 (default). This change will first check if the receiver
level is zero and only then set it to the default. This still avoids the
interrupt storm when the receiver level is zero.
Fixes: a81dbd0463 ("serial: imx: set receiver level before starting uart")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Link: https://lore.kernel.org/r/20240703112543.148304-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the match() callback, the struct device_driver * should not be
changed, so change the function callback to be a const *. This is one
step of many towards making the driver core safe to have struct
device_driver in read-only memory.
Because the match() callback is in all busses, all busses are modified
to handle this properly. This does entail switching some container_of()
calls to container_of_const() to properly handle the constant *.
For some busses, like PCI and USB and HV, the const * is cast away in
the match callback as those busses do want to modify those structures at
this point in time (they have a local lock in the driver structure.)
That will have to be changed in the future if they wish to have their
struct device * in read-only-memory.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Alex Elder <elder@kernel.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/2024070136-wrongdoer-busily-01e8@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmaB0NweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGkvwH/36UJRk/o6wvXnyH
E6QjCSWo2226APyWks22NjtC3I/8Iqdvkneuh6wG0qL2sXAB078EMjUq5R81bF8H
wWFBJwetjYTp8GEyLioMEb2wCH/J3R29dLFC4UYTplafXRGP6//xcpJaKmTxcgdR
31IzvTPXbApZ7L3k1U6rA2bK9PNKcFCOvZlrNMUCuwMrabymHsDfOUt1DqXyg2xp
zjqiWYBwlklozmgawSWt/mdEgkWuTcAbg+KyqDVQF59s9aj/OOwZ0j+HACq5V8CM
quTPIAYL6CC9p7uxa69lGr/sgC0Is/BZLPX7RTZAwCgarGvnX+1HUsjDcaFCtrVg
O6fPUV8=
=pgUx
-----END PGP SIGNATURE-----
Merge 6.10-rc6 into tty-next
This resolves the merge issues in the 8250 code due to some reverts in
6.10-rc6 in the console changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 787a1cabac.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a0f32e2dd9.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a8b04cfe7d.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 4547cd76f0.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b20172ca6b.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When bcm63xx-uart was converted to uart_port_tx_limited(), it implicitly
added a call to stop_tx(). This causes garbage to be put out on the
serial console. To fix this, pass UART_TX_NOSTOP in flags, and manually
call stop_tx() ourselves analogue to how a similar issue was fixed in
commit 7be50f2e8f ("serial: mxs-auart: fix tx").
Fixes: d11cc8c3c4 ("tty: serial: use uart_port_tx_limited()")
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Doug Brown <doug@schmorgal.com>
Link: https://lore.kernel.org/r/20240606195632.173255-4-doug@schmorgal.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the receiver level to something > 0 before calling imx_uart_start_rx
in rs485_config. This is necessary to avoid an interrupt storm that
might prevent the system from booting. This was seen on an i.MX7 device
when the rs485-rts-active-low property was active in the device tree.
Fixes: 6d215f83e5 ("serial: imx: warn user when using unsupported configuration")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Link: https://lore.kernel.org/r/20240621153829.183780-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the colfires have up to 5 UARTs but MCF54418 has up-to 10 !
Change the maximum value authorized.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@yoseli.org>
Cc: stable <stable@kernel.org>
Fixes: 2545cf6e94 ("m68knommu: allow 4 coldfire serial ports")
Link: https://lore.kernel.org/r/20240620-upstream-uart-v1-1-a9d0d95fb19e@yoseli.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normally, the number of ports is indicated by the third digit of the
device ID on Moxa PCI serial boards. For example, `0x1121` indicates a
device with 2 ports.
However, `CP116E_A_A` and `CP116E_A_B` are exceptions; they have 8
ports, but the third digit of the device ID is `6`.
This patch introduces a function to retrieve the number of ports on Moxa
PCI serial boards, addressing the issue described above.
Fixes: 37058fd5d2 ("tty: serial: 8250: Add support for MOXA Mini PCIe boards")
Cc: stable <stable@kernel.org>
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240617063058.18866-1-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some boards connect a GPIO to the reset pin, and the reset pin needs
to be set up correctly before accessing the chip.
Add a function to handle the chip reset. If the reset-gpios is defined
in the DT, do hardware reset through this GPIO, otherwise do software
reset as before.
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20240618112620.152848-2-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_isa_init_ports() uses home grown approach to make itself
a singleton. Instead, explicitly show that we initialise ISA ports
once by providing a helper function which calls the original function
via DO_ONCE() macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240606184841.3102545-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/8250/8250_base.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/8250/8250_pxa.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/8250/serial_cs.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/esp32_uart.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/esp32_acm.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/owl-uart.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/n_hdlc.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/n_gsm.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/ttynull.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/goldfish.o
Add all missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240607-md-drivers-tty-v1-1-50a7efb8bed8@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial support for RZ/V2H(P) SoC with earlycon.
The SCIF interface in the Renesas RZ/V2H(P) is similar to that available
in the RZ/G2L (R9A07G044) SoC, with the following differences:
- RZ/V2H(P) SoC has three additional interrupts: one for Tx end/Rx ready
and two for Rx and Tx buffer full, all of which are edge-triggered.
- RZ/V2H(P) supports asynchronous mode, whereas RZ/G2L supports both
synchronous and asynchronous modes.
- There are differences in the configuration of certain registers such
as SCSMR, SCFCR, and SCSPTR between the two SoCs.
To handle these differences on RZ/V2H(P) SoC SCIx_RZV2H_SCIF_REGTYPE
is added.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240604170513.522631-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoCs like StarFive JH7110 require two or more resets.
So change to use the reset array API to get resets.
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Link: https://lore.kernel.org/r/20240604084729.57239-3-hal.feng@starfivetech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmZvTbAeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGVksIAJEn4a9IVM8FNCJy
Dxo0BItD1/qJ5mLDptqUFRKlxInjbojofz5CyoeIeXb0DwRfB16ALXqNXAkd3APi
saoOpfjFsg2H2OqL9CHdkzWcJEAq2lDnL0zaOjumeDVu/EyeT+tC4e4hq1e6Bm0E
fPC5ms2b+07DF9Rg6/DW8yPbdM5n6Mz1bRd3fQOIgvpM3yGOyGztEBgTRub/ZUgH
5pNJauknFAZgdiWhgNpc+lPWYZbgHKULQPhUBPdVhDIXPtQNUlKgNTQc6+L0Nmbb
K1sG1q7FLeMJOTFGQfD4r26X5DNQUi894q/9SX8X7rcrECdJKcw2WjVyB4myADpf
ae2gP+A=
=XjWP
-----END PGP SIGNATURE-----
Merge tag 'v6.10-rc4' into tty-next
We need the tty/serial fixes in here as well
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d492164381
("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
removed Kconfig SPI_MASTER or I2C dependency for SERIAL_SC16IS7XX (core).
This removal was done because I inadvertently misinterpreted some review
comments.
Because of that, the driver question now pops up if both I2C and
SPI_MASTER are disabled.
Re-add Kconfig SPI_MASTER or I2C dependency to fix the problem.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d492164381 ("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240603152601.3689319-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d492164381
("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
renamed SERIAL_SC16IS7XX_CORE by SERIAL_SC16IS7XX. This means that some
configs should have been updated when I submitted the original patch, but
unfortunately they were not. Geert mentioned for example:
arch/mips/configs/cu1??0-neo_defconfig
Rename SERIAL_SC16IS7XX to SERIAL_SC16IS7XX_CORE so that existing configs
will still work correctly.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d492164381 ("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240603152601.3689319-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently, suspend testing on sc7180-trogdor based devices has started
to sometimes fail with messages like this:
port a88000.serial:0.0: PM: calling pm_runtime_force_suspend+0x0/0xf8 @ 28934, parent: a88000.serial:0
port a88000.serial:0.0: PM: dpm_run_callback(): pm_runtime_force_suspend+0x0/0xf8 returns -16
port a88000.serial:0.0: PM: pm_runtime_force_suspend+0x0/0xf8 returned -16 after 33 usecs
port a88000.serial:0.0: PM: failed to suspend: error -16
I could reproduce these problems by logging in via an agetty on the
debug serial port (which was _not_ used for kernel console) and
running:
cat /var/log/messages
...and then (via an SSH session) forcing a few suspend/resume cycles.
Tracing through the code and doing some printf()-based debugging shows
that the -16 (-EBUSY) comes from the recently added
serial_port_runtime_suspend().
The idea of the serial_port_runtime_suspend() function is to prevent
the port from being _runtime_ suspended if it still has bytes left to
transmit. Having bytes left to transmit isn't a reason to block
_system_ suspend, though. If a serdev device in the kernel needs to
block system suspend it should block its own suspend and it can use
serdev_device_wait_until_sent() to ensure bytes are sent.
The DEFINE_RUNTIME_DEV_PM_OPS() used by the serial_port code means
that the system suspend function will be pm_runtime_force_suspend().
In pm_runtime_force_suspend() we can see that before calling the
runtime suspend function we'll call pm_runtime_disable(). This should
be a reliable way to detect that we're called from system suspend and
that we shouldn't look for busyness.
Fixes: 43066e3222 ("serial: port: Don't suspend if the port is still busy")
Cc: stable@vger.kernel.org
Reviewed-by: Tony Lindgren <tony.lindgren@linux.intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240531080914.v3.1.I2395e66cf70c6e67d774c56943825c289b9c13e4@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FIFO is 64 bytes, but the FCR is configured to fire the TX interrupt
when the FIFO is half empty (bit 3 = 0). Thus, we should only write 32
bytes when a TX interrupt occurs.
This fixes a problem observed on the PXA168 that dropped a bunch of TX
bytes during large transmissions.
Fixes: ab28f51c77 ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: Doug Brown <doug@schmorgal.com>
Link: https://lore.kernel.org/r/20240519191929.122202-1-doug@schmorgal.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d9666dfb31.
The container of the struct dw8250_port_data is private to the actual
driver. In particular, 8250_lpss and 8250_dw use different data types
that are assigned to the UART port private_data. Hence, it must not
be used outside the specific driver.
Fix the mistake made in the past by moving the respective definitions
to the specific driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240514190730.2787071-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The container of the struct dw8250_port_data is private to the actual
driver. In particular, 8250_lpss and 8250_dw use different data types
that are assigned to the UART port private_data. Hence, it must not
be used outside the specific driver.
Currently the only cpr_val is required by the common code, make it
be available via struct dw8250_port_data.
This fixes the UART breakage on Intel Galileo boards.
Fixes: 593dea000b ("serial: 8250: dw: Allow to use a fallback CPR value if not synthesized")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240514190730.2787071-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract platform driver to a separate module for better maintenance
and to reduce churn on 8250_core part changes when it's solely related
to the former. No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Sunil V L <sunilvl@ventanamicro.com>
Tested-by: Sunil V L <sunilvl@ventanamicro.com>
Link: https://lore.kernel.org/r/20240506140308.4040735-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract RSA bits to a separate module for better maintenance
and to reduce a churn on 8250_core part changes when it's solely
related to the former. No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240506140308.4040735-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct imx_port does have a struct uart_port as its first member, so
the current code works, but it is not how kernel code is usually
written.
Similar to many other serial drivers, introduce and use a
to_imx_port() helper based on container_of(). No functional change.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240528094022.2161066-1-linux@rasmusvillemoes.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add `__free` function attribute to `ap` and `match` pointer
initialisations which ensure that the pointers are freed as soon as they
go out of scope, thus removing the need to manually free them using
`of_node_put`.
This also removes the need for the `goto` statement and the `rc`
variable.
Suggested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Shresth Prasad <shresthprasad7@gmail.com>
Link: https://lore.kernel.org/r/20240518114051.18125-3-shresthprasad7@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small TTY and Serial driver fixes that missed the
6.9-final merge window, but have been in my tree for weeks (my fault,
travel caused me to miss this.)
These fixes include:
- more n_gsm fixes for reported problems
- 8520_mtk driver fix
- 8250_bcm7271 driver fix
- sc16is7xx driver fix
All of these have been in linux-next for weeks without any reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZlBGKQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylOkwCfUOa00YQt3jJwBEC9bQUprW1z95MAoKW00V5g
UJgQ7+1d+o4bT/ib5xpj
=/O0m
-----END PGP SIGNATURE-----
Merge tag 'tty-6.10-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small TTY and Serial driver fixes that missed the
6.9-final merge window, but have been in my tree for weeks (my fault,
travel caused me to miss this)
These fixes include:
- more n_gsm fixes for reported problems
- 8520_mtk driver fix
- 8250_bcm7271 driver fix
- sc16is7xx driver fix
All of these have been in linux-next for weeks without any reported
problems"
* tag 'tty-6.10-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sc16is7xx: fix bug in sc16is7xx_set_baud() when using prescaler
serial: 8250_bcm7271: use default_mux_rate if possible
serial: 8520_mtk: Set RTS on shutdown for Rx in-band wakeup
tty: n_gsm: fix missing receive state reset after mode switch
tty: n_gsm: fix possible out-of-bounds in gsm0_receive()
Here is the big set of tty/serial driver changes for 6.10-rc1. Included
in here are:
- Usual good set of api cleanups and evolution by Jiri Slaby to make
the serial interfaces move out of the 1990's by using kfifos instead
of hand-rolling their own logic.
- 8250_exar driver updates
- max3100 driver updates
- sc16is7xx driver updates
- exar driver updates
- sh-sci driver updates
- tty ldisc api addition to help refuse bindings
- other smaller serial driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZk4Cvg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymqpwCgnHU1NeBBUsvoSDOLk5oApIQ4jVgAn102jWlw
3dNDhA4i3Ay/mZdv8/Kj
=TI+P
-----END PGP SIGNATURE-----
Merge tag 'tty-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty/serial driver changes for 6.10-rc1.
Included in here are:
- Usual good set of api cleanups and evolution by Jiri Slaby to make
the serial interfaces move out of the 1990's by using kfifos
instead of hand-rolling their own logic.
- 8250_exar driver updates
- max3100 driver updates
- sc16is7xx driver updates
- exar driver updates
- sh-sci driver updates
- tty ldisc api addition to help refuse bindings
- other smaller serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (113 commits)
serial: Clear UPF_DEAD before calling tty_port_register_device_attr_serdev()
serial: imx: Raise TX trigger level to 8
serial: 8250_pnp: Simplify "line" related code
serial: sh-sci: simplify locking when re-issuing RXDMA fails
serial: sh-sci: let timeout timer only run when DMA is scheduled
serial: sh-sci: describe locking requirements for invalidating RXDMA
serial: sh-sci: protect invalidating RXDMA on shutdown
tty: add the option to have a tty reject a new ldisc
serial: core: Call device_set_awake_path() for console port
dt-bindings: serial: brcm,bcm2835-aux-uart: convert to dtschema
tty: serial: uartps: Add support for uartps controller reset
arm64: zynqmp: Add resets property for UART nodes
dt-bindings: serial: cdns,uart: Add optional reset property
serial: 8250_pnp: Switch to DEFINE_SIMPLE_DEV_PM_OPS()
serial: 8250_exar: Keep the includes sorted
serial: 8250_exar: Make type of bit the same in exar_ee_*_bit()
serial: 8250_exar: Use BIT() in exar_ee_read()
serial: 8250_exar: Switch to use dev_err_probe()
serial: 8250_exar: Return directly from switch-cases
serial: 8250_exar: Decrease indentation level
...
-----BEGIN PGP SIGNATURE-----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=xjoS
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Skip E820 checks for MCFG ECAM regions for new (2016+) machines,
since there's no requirement to describe them in E820 and some
platforms require ECAM to work (Bjorn Helgaas)
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific (Damien
Le Moal)
- Remove last user and pci_enable_device_io() (Heiner Kallweit)
- Wait for Link Training==0 to avoid possible race (Ilpo Järvinen)
- Skip waiting for devices that have been disconnected while
suspended (Ilpo Järvinen)
- Clear Secondary Status errors after enumeration since Master Aborts
and Unsupported Request errors are an expected part of enumeration
(Vidya Sagar)
MSI:
- Remove unused IMS (Interrupt Message Store) support (Bjorn Helgaas)
Error handling:
- Mask Genesys GL975x SD host controller Replay Timer Timeout
correctable errors caused by a hardware defect; the errors cause
interrupts that prevent system suspend (Kai-Heng Feng)
- Fix EDR-related _DSM support, which previously evaluated revision 5
but assumed revision 6 behavior (Kuppuswamy Sathyanarayanan)
ASPM:
- Simplify link state definitions and mask calculation (Ilpo
Järvinen)
Power management:
- Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports, where BIOS
apparently doesn't know how to put them back in D0 (Mario
Limonciello)
CXL:
- Support resetting CXL devices; special handling required because
CXL Ports mask Secondary Bus Reset by default (Dave Jiang)
DOE:
- Support DOE Discovery Version 2 (Alexey Kardashevskiy)
Endpoint framework:
- Set endpoint BAR to be 64-bit if the driver says that's all the
device supports, in addition to doing so if the size is >2GB
(Niklas Cassel)
- Simplify endpoint BAR allocation and setting interfaces (Niklas
Cassel)
Cadence PCIe controller driver:
- Drop DT binding redundant msi-parent and pci-bus.yaml (Krzysztof
Kozlowski)
Cadence PCIe endpoint driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
Freescale Layerscape PCIe controller driver:
- Convert DT binding to YAML (Frank Li)
MediaTek MT7621 PCIe controller driver:
- Add DT binding missing 'reg' property for child Root Ports
(Krzysztof Kozlowski)
- Fix theoretical string truncation in PHY name (Sergio Paracuellos)
NVIDIA Tegra194 PCIe controller driver:
- Return success for endpoint probe instead of falling through to the
failure path (Vidya Sagar)
Renesas R-Car PCIe controller driver:
- Add DT binding missing IOMMU properties (Geert Uytterhoeven)
- Add DT binding R-Car V4H compatible for host and endpoint mode
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
- Add DT binding missing maxItems to ep-gpios (Krzysztof Kozlowski)
- Set the Subsystem Vendor ID, which was previously zero because it
was masked incorrectly (Rick Wertenbroek)
Synopsys DesignWare PCIe controller driver:
- Restructure DBI register access to accommodate devices where this
requires Refclk to be active (Manivannan Sadhasivam)
- Remove the deinit() callback, which was only need by the
pcie-rcar-gen4, and do it directly in that driver (Manivannan
Sadhasivam)
- Add dw_pcie_ep_cleanup() so drivers that support PERST# can clean
up things like eDMA (Manivannan Sadhasivam)
- Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to make it parallel
to dw_pcie_ep_init() (Manivannan Sadhasivam)
- Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to
reflect the actual functionality (Manivannan Sadhasivam)
- Call dw_pcie_ep_init_registers() directly from all the glue
drivers, not just those that require active Refclk from the host
(Manivannan Sadhasivam)
- Remove the "core_init_notifier" flag, which was an obscure way for
glue drivers to indicate that they depend on Refclk from the host
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Add DT binding J784S4 SoC Device ID (Siddharth Vadapalli)
- Add DT binding J722S SoC support (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Add DT binding missing num-viewport, phys and phy-name properties
(Jan Kiszka)
Miscellaneous:
- Constify and annotate with __ro_after_init (Heiner Kallweit)
- Convert DT bindings to YAML (Krzysztof Kozlowski)
- Check for kcalloc() failure in of_pci_prop_intr_map() (Duoming
Zhou)"
* tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Do not wait for disconnected devices when resuming
x86/pci: Skip early E820 check for ECAM region
PCI: Remove unused pci_enable_device_io()
ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io()
PCI: Update pci_find_capability() stub return types
PCI: Remove PCI_IRQ_LEGACY
scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY
scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
dt-bindings: PCI: rockchip,rk3399-pcie: Add missing maxItems to ep-gpios
Revert "genirq/msi: Provide constants for PCI/IMS support"
Revert "x86/apic/msi: Enable PCI/IMS"
Revert "iommu/vt-d: Enable PCI/IMS"
Revert "iommu/amd: Enable PCI/IMS"
Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support"
...
Nine patches this cycle and they split into just three topics:
1. Adopt coccinelle's recommendation to adopt str_plural().
2. A set of seven patches to refactor kdb_read() to improve both code clarity
and it's discipline with respect to fixed size buffers. This isn't just a
refactor. Between them these also fix a cursor movement redraw problem and
two buffer overflows (one latent and one real, albeit difficult to
tickle).
3. Fix an NMI-safety problem when enqueuing kdb's keyboard reset code.
I wrote eight of the nine patches in this collection so many thanks to Doug
Anderson for the reviews. The changes that affects drivers/tty/serial is
acked by Greg KH.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=vVUC
-----END PGP SIGNATURE-----
Merge tag 'kgdb-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux
Pull kgdb updates from Daniel Thompson:
"Nine patches this cycle and they split into just three topics:
- Adopt coccinelle's recommendation to adopt str_plural()
- A set of seven patches to refactor kdb_read() to improve both code
clarity and its discipline with respect to fixed size buffers.
This isn't just a refactor. Between them these also fix a cursor
movement redraw problem and two buffer overflows (one latent and
one real, albeit difficult to tickle).
- Fix an NMI-safety problem when enqueuing kdb's keyboard reset code
I wrote eight of the nine patches in this collection so many thanks to
Doug Anderson for the reviews. The changes that affects
drivers/tty/serial is acked by Greg KH"
* tag 'kgdb-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
serial: kgdboc: Fix NMI-safety problems from keyboard reset code
kdb: Simplify management of tmpbuffer in kdb_read()
kdb: Replace double memcpy() with memmove() in kdb_read()
kdb: Use format-specifiers rather than memset() for padding in kdb_read()
kdb: Merge identical case statements in kdb_read()
kdb: Fix console handling when editing and tab-completing commands
kdb: Use format-strings rather than '\0' injection in kdb_read()
kdb: Fix buffer overflow during tab-complete
kdb: Use str_plural() to fix Coccinelle warning
I had investigated dropping support for alpha EV5 and earlier a while
ago after noticing that this is the only supported CPU family
in the kernel without native byte access and that Debian has already
dropped support for this generation last year [1] in order to
improve performance for the newer machines.
This topic came up again when Paul E. McKenney noticed that
parts of the RCU code already rely on byte access and do not
work on alpha EV5 reliably, so we decided on using my series to
avoid the problem entirely.
Al Viro did another series for alpha to address all the known build
issues. I rebased his patches without any further changes and included
it as a baseline for my work here to avoid conflicts and allow
backporting the fixes to stable kernels for the now removed hardware
support as well.
-----BEGIN PGP SIGNATURE-----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=0Sgm
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-alpha' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull alpha updates from Arnd Bergmann:
"I had investigated dropping support for alpha EV5 and earlier a while
ago after noticing that this is the only supported CPU family in the
kernel without native byte access and that Debian has already dropped
support for this generation last year [1] in order to improve
performance for the newer machines.
This topic came up again when Paul McKenney noticed that parts of the
RCU code already rely on byte access and do not work on alpha EV5
reliably, so we decided on using my series to avoid the problem
entirely.
Al Viro did another series for alpha to address all the known build
issues. I rebased his patches without any further changes and included
it as a baseline for my work here to avoid conflicts and allow
backporting the fixes to stable kernels for the now removed hardware
support as well"
[ I dearly loved alpha back in the days, but the lack of byte and word
operations was a horrible mistake and made everything worse -
including very much the crazy IO contortions that resulted from it.
It certainly wasn't the only mistake in the architecture, but it's the
first-order issue.
So while it's a bit sad to see the support for my first alpha go away,
if you want to run museum hardware, maybe you should use museum
kernels.. - Linus ]
* tag 'asm-generic-alpha' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
alpha: drop pre-EV56 support
alpha: cabriolet: remove EV5 CPU support
alpha: remove LCA and APECS based machines
alpha: sable: remove early machine support
alpha: remove DECpc AXP150 (Jensen) support
alpha: trim the unused stuff from asm-offsets.c
alpha: jensen, t2 - make __EXTERN_INLINE same as for the rest
alpha: core_lca: take the unused functions out
alpha: missing includes
alpha: sys_sio: fix misspelled ifdefs
alpha: don't make functions public without a reason
alpha: add clone3() support
alpha: fix modversions for strcpy() et.al.
alpha: sort scr_mem{cpy,move}w() out
If a serdev_device_driver is already loaded for a serdev_tty_port when it
gets registered by tty_port_register_device_attr_serdev() then that
driver's probe() method will be called immediately.
The serdev_device_driver's probe() method should then be able to call
serdev_device_open() successfully, but because UPF_DEAD is still dead
serdev_device_open() will fail with -ENXIO in this scenario:
serdev_device_open()
ctrl->ops->open() /* this callback being ttyport_open() */
tty->ops->open() /* this callback being uart_open() */
tty_port_open()
port->ops->activate() /* this callback being uart_port_activate() */
Find bit UPF_DEAD is set in uport->flags and fail with errno -ENXIO.
Fix this be clearing UPF_DEAD before tty_port_register_device_attr_serdev()
note this only moves up the UPD_DEAD clearing a small bit, before:
tty_port_register_device_attr_serdev();
mutex_unlock(&tty_port.mutex);
uart_port.flags &= ~UPF_DEAD;
mutex_unlock(&port_mutex);
after:
uart_port.flags &= ~UPF_DEAD;
tty_port_register_device_attr_serdev();
mutex_unlock(&tty_port.mutex);
mutex_unlock(&port_mutex);
Reported-by: Weifeng Liu <weifeng.liu.z@gmail.com>
Closes: https://lore.kernel.org/platform-driver-x86/20240505130800.2546640-1-weifeng.liu.z@gmail.com/
Tested-by: Weifeng Liu <weifeng.liu.z@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240509141549.63704-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the default TX trigger level of 2 in non-DMA mode (meaning that an
interrupt is generated when less than 2 characters are left in the
FIFO), we have observed frequent buffer underruns at 115200 Baud on an
i.MX8M Nano. This can cause communication issues if the receiving side
expects a continuous transfer.
Increasing the level to 8 makes the UART trigger an interrupt earlier,
giving the kernel enough time to refill the FIFO, at the cost of
triggering one interrupt per ~24 instead of ~30 bytes of transmitted
data (as the i.MX UART has a 32 byte FIFO).
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240508133744.35858-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_pnp sets drvdata to line + 1 if the probe is successful. The users
of drvdata are in remove, suspend and resume callbacks, none of which
will be called if probe failed. The line acquired from drvdata can
never be zero in those functions and the checks for that can be
removed.
Eliminate also +/-1 step because all users of line subtract 1 from the
value.
These might have been leftover from legacy PM callbacks that could
be called without probe being successful.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240506121202.11253-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hrtimer for RXDMA timeout was unconditionally restarted in the RXDMA
complete handler ignoring the fact that setting up DMA may fail and PIO
is used instead. Explicitly stop the timer when DMA is completed and
only restart it when setting up DMA was successful. This makes the
intention of the timer much clearer, the driver easier to understand and
simplifies assumptions about the timer. The latter avoids race
conditions if these assumptions were not met or confused.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240506114016.30498-9-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using a high speed clock with a low baud rate, the 4x prescaler is
automatically selected if required. In that case, sc16is7xx_set_baud()
properly configures the chip registers, but returns an incorrect baud
rate by not taking into account the prescaler value. This incorrect baud
rate is then fed to uart_update_timeout().
For example, with an input clock of 80MHz, and a selected baud rate of 50,
sc16is7xx_set_baud() will return 200 instead of 50.
Fix this by first changing the prescaler variable to hold the selected
prescaler value instead of the MCR bitfield. Then properly take into
account the selected prescaler value in the return value computation.
Also add better documentation about the divisor value computation.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240430200431.4102923-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a scenario when resuming from some power saving states
with no_console_suspend where console output can be generated
before the 8250_bcm7271 driver gets the opportunity to restore
the baud_mux_clk frequency. Since the baud_mux_clk is at its
default frequency at this time the output can be garbled until
the driver gets the opportunity to resume.
Since this is only an issue with console use of the serial port
during that window and the console isn't likely to use baud
rates that require alternate baud_mux_clk frequencies, allow the
driver to select the default_mux_rate if it is accurate enough.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240424222559.1844045-1-opendmb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Rx in-band wakeup is enabled, set RTS to true in mtk8250_shutdown()
so the connected device can still send message and trigger IRQ when the
system is suspended.
Fixes: 18c9d4a3c2 ("serial: When UART is suspended, set RTS to false")
Cc: stable <stable@kernel.org>
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Link: https://lore.kernel.org/r/20240424130619.2924456-1-treapking@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the UART port is used as a console, no_console_suspend is
available in bootargs and UART port is part of a software-controlled power
domain we need to call device_set_awake_path(). This lets the power
domain core code know that this domain should not be powered off
during system suspend. Otherwise, the UART port power domain is turned off,
nothing is printed while suspending and the suspend/resume process is
blocked. This was detected on the Renesas RZ/G3S SoC while adding support
for power domains.
Based on code investigation (on v6.9-rc5), this issue is present on other
SoCs (e.g., Renesas R-Mobile A1 [1], IMX8QXP [2]) and different SoCs have
particular implementation to handle it. Due to this the patch added the
call of device_set_awake_path() in uart_suspend_port() instead of having
it in the platform specific UART driver.
[1] drivers/pmdomain/renesas/rmobile-sysc.c:116
[2] drivers/pmdomain/imx/scu-pd.c:357
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tony Lindgren <tony.lindgren@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240430095930.2806067-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for an optional reset for the uartps controller using
the reset driver. If the uartps node contains the "resets" property,
then cdns_uart_startup performs uartps controller non-pulse out of reset
and reset in exit path.
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Link: https://lore.kernel.org/r/20240425062358.1347684-4-manikanta.guntupalli@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SIMPLE_DEV_PM_OPS() is deprecated, replace it with the
DEFINE_SIMPLE_DEV_PM_OPS() and use pm_sleep_ptr() for setting
the driver's PM routines.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240422083237.207447-1-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make type of bit parameter and returned one the same in exar_ee_*_bit().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-13-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use BIT() in exar_ee_read() like other functions do.
While at it, explain the EEPROM type and the dummy bit requirement.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-12-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to use dev_err_probe() to simplify the error path and
unify a message template.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-11-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two similar switch-cases which use different style.
Unify them and one more to return from the cases directly.
While at it, add missing default in another switch-case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may reuse ->setup() for the same purpose as it was done before.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use PCI_SUBVENDOR_ID_IBM for subvendor ID instead of vendor one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel doc validator is not happy:
warning: Function parameter or struct member 'pcidev' not described in 'cti_get_port_type_xr17c15x_xr17v25x'
warning: Function parameter or struct member 'pcidev' not described in 'cti_get_port_type_fpga'
warning: Function parameter or struct member 'pcidev' not described in 'cti_get_port_type_xr17v35x'
Add missed descriptions.
Fixes: f7ce070629 ("serial: exar: add CTI specific setup code")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI core may return positive codes for the specific errors.
There is a special API to convert them to negative stanrard ones.
Use that API to avoid returning positive values as error codes.
Fixes: f7ce070629 ("serial: exar: add CTI specific setup code")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is one of the hackiest Alpha machines, and the only one without
PCI support. Removing this allows cleaning up code in eise and tty
drivers in addition to the architecture code.
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently, when kdb is compiled with keyboard support, then we will use
schedule_work() to provoke reset of the keyboard status. Unfortunately
schedule_work() gets called from the kgdboc post-debug-exception
handler. That risks deadlock since schedule_work() is not NMI-safe and,
even on platforms where the NMI is not directly used for debugging, the
debug trap can have NMI-like behaviour depending on where breakpoints
are placed.
Fix this by using the irq work system, which is NMI-safe, to defer the
call to schedule_work() to a point when it is safe to call.
Reported-by: Liuye <liu.yeC@h3c.com>
Closes: https://lore.kernel.org/all/20240228025602.3087748-1-liu.yeC@h3c.com/
Cc: stable@vger.kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240424-kgdboc_fix_schedule_work-v2-1-50f5a490aec5@linaro.org
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-7-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want the tty fixes in here as well, and it resolves a merge conflict
in:
drivers/tty/serial/serial_core.c
as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The -next commit f8fef2fa41 (tty: msm_serial: use
dmaengine_prep_slave_sg()), switched to using dma_map_sg(). But the
return value of dma_map_sg() is special: it returns number of elements
mapped. And not a standard error value.
The commit also forgot to reset dma->tx_sg in case of this failure.
Fix both these mistakes.
Thanks to Marek who helped debugging this.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20240419080931.30949-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-Fix several "missing identifier name" warnings from checkpatch in
struct exar8250_platform and struct exar8250_board.
Example:
WARNING: function definition argument <arg> should also have an
identifier name
- Fix space before tab warning from checkpatch:
WARNING: please, no space before tabs
+ * 0^I^I2 ^IMode bit 0$
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/f7fa6c16cb5f2c8c1c7cb7d29f80bc7be53f91ab.1713382717.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a large patch but is only additions. All changes and removals
are made in previous patches in this series.
- Add CTI board_init and port setup functions for each UART type
- Add CTI_EXAR_DEVICE() and CTI_PCI_DEVICE() macros
- Add support for reading a word from the Exar EEPROM.
- Add support for configuring and setting a single MPIO
- Add various helper functions for CTI boards.
- Add osc_freq to struct exar8250
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/ae4a66e7342b686cb8d4b15317585dfb37222cf4.1713382717.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add an optional "board_init()" function pointer to struct exar8250_board
which is called once during probe prior to setting up the ports. It will
be used in subsequent patches of this series.
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/0e72a3154114c733283ff273bc1e31456ee101f4.1713382717.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preparatory patch removing existing Connect Tech setup code and
CONNECT_DEVICE macro.
Subsequent patches in this series will add in new UART family specific
setup code and new device definition macros to allow for supporting CTI
serial cards with Exar PCI IDs and CTI PCI IDs.
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/06a04b6c683ca20c50646cc0836be869c2dacd87.1713382717.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an UART is opened that still has .throttled set from a previous
open, the RX interrupt is enabled but the irq handler doesn't consider
it. This easily results in a stuck irq with the effect to occupy the CPU
in a tight loop.
So reset the throttle state in .startup() to ensure that RX irqs are
handled.
Fixes: d1ec8a2eab ("serial: stm32: update throttle and unthrottle ops for dma mode")
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/a784f80d3414f7db723b2ec66efc56e1ad666cbf.1713344161.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is a stuck irq that the handler doesn't address, returning
IRQ_HANDLED unconditionally makes it impossible for the irq core to
detect the problem and disable the irq. So only return IRQ_HANDLED if
an event was handled.
A stuck irq is still problematic, but with this change at least it only
makes the UART nonfunctional instead of occupying the (usually only) CPU
by 100% and so stall the whole machine.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5f92603d0dfd8a5b8014b2b10a902d91e0bb881f.1713344161.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 16550a serial port based on the ACPI table requires obtaining the
reg-shift attribute. In the ACPI scenario, If the reg-shift property
is not configured like in DTS, the 16550a serial driver cannot read or
write controller registers properly during initialization.
Signed-off-by: Guanbing Huang <albanhuang@tencent.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bing Fan <tombinfan@tencent.com>
Tested-by: Linheng Du <dylanlhdu@tencent.com>
Link: https://lore.kernel.org/r/4726ecea8f7bfbfe42501b4f6ad9fe5b38994574.1713234515.git.albanhuang@tencent.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function __uart_read_properties doesn't cover PNP devices, so add IRQ
processing for PNP devices in the branch.
Signed-off-by: Guanbing Huang <albanhuang@tencent.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bing Fan <tombinfan@tencent.com>
Tested-by: Linheng Du <dylanlhdu@tencent.com>
Link: https://lore.kernel.org/r/7f4ca31ef1cab4c6ecad22fafd82117686b696be.1713234515.git.albanhuang@tencent.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dw8250_serial_inq() uses unsigned int variable to store 8-bit value.
Due to that it needs a cast which can be avoided by switching to use
u8 instead of unsigned int.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240412173937.187442-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By waiting at most 1 second for USR2_TXDC to be set, we avoid a potential
deadlock.
In case of the timeout, there is not much we can do, so we simply ignore
the transmitter state and optimistically try to continue.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/919647898c337a46604edcabaf13d42d80c0915d.1712837613.git.esben@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After conversion to the kfifo, it becomes possible to extract two helper
functions for better maintenance and code deduplication. Do it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240409174057.1104262-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pengfei Xu reports, that the -next commit 1788cf6a91 (tty: serial:
switch from circ_buf to kfifo) tries to emit a WARNING and that leads to
lockdep errors. Obviously we cannot print anything from uart_put_char()!
This WARN_ON_ONCE() was/is a debug aid to check if the condition in
uart_put_char() can happen at all. Pengfei Xu confirmed it can. Unlike
me and kbuild bot in my queue.
Second, I completely forgot about it, so I did not remove it in the
final version, nor mentioned it in the commit log.
Drop it now as we are all good. And we even have stack traces (and a
reproducer)!
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/20240416071904.21440-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek reports, that the -next commit 1788cf6a91 (tty: serial: switch
from circ_buf to kfifo) broke meson_uart and qcom_geni_serial. The
commit mistakenly advanced the kfifo twice: once by
uart_fifo_get()/kfifo_out() and second time by uart_xmit_advance().
To advance the fifo only once, drop the superfluous uart_xmit_advance()
from both.
To count the TX statistics properly, use uart_fifo_out() in
qcom_geni_serial (meson_uart_start_tx() already uses that).
I checked all other uses of uart_xmit_advance() and they appear correct:
either they are finishing DMA transfers or are after peek/linear_ptr
(i.e. they do not advance fifo).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 1788cf6a91 ("tty: serial: switch from circ_buf to kfifo")
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20240416054825.6211-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are seeing start_tx being called after port shutdown as noted by Jiri.
This happens because we are missing the startup and shutdown related
functions for the serial base port.
Let's fix the issue by adding startup and shutdown functions for the
serial base port to block tx flushing for the serial base port when the
port is not in use.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Cc: stable <stable@kernel.org>
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240411055848.38190-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Jiri rightfully pointed out the current to_max3100_port() macro
implementation is fragile in a sense that it expects the variable
name to be port, otherwise it blow up the build.
Change this to be static inline to prevent bad compilation.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240410141135.1378948-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable tmout is being assigned a value that is never read, it is
being re-assinged in the following for-loop statement. The assignment
is redundant and can be removed.
Cleans up clang scan warning:
drivers/tty/serial/omap-serial.c:1096:3: warning: Value stored to 'tmout'
is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240411085537.306020-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to inline serial_base_add_isa_preferred_console() based on
CONFIG_SERIAL_8250_CONSOLE and not based on CONFIG_SERIAL_CORE_CONSOLE.
Otherwise we can get the follwoing error as noted by Stephen:
ERROR: modpost: "serial_base_add_isa_preferred_console"
[drivers/tty/serial/8250/8250.ko] undefined!
We also have a duplicate inlined serial_base_add_isa_preferred_console(),
in serial_base_bus.c added by the same commit by accident, let's drop it.
Fixes: a8b04cfe7d ("serial: 8250: Add preferred console in serial8250_isa_init_ports()")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240411080622.11929-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since each I2C/SPI probe function can modify sc16is7xx_regcfg at the same
time, change structure to be constant and do the required modifications on
a local copy.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240409154253.3043822-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before, sc16is7xx_lines was checked for a free (zero) bit first, and then
later it was set only if UART port registration succeeded. Now that
sc16is7xx_lines is shared for the I2C and SPI drivers, there is a
possibility that the two drivers can simultaneously try to reserve the same
line bit at the same time.
To prevent this, make sure line allocation is reserved atomically, and use
a new variable to hold the status of UART port registration.
Now that we no longer need to search if a bit is set, it is now possible
to simplify sc16is7xx_lines allocation by using the IDA framework.
Link: https://lore.kernel.org/all/20231212150302.a9ec5d085a4ba65e89ca41af@hugovil.com/
Link: https://lore.kernel.org/all/CAHp75VebCZckUrNraYQj9k=Mrn2kbYs1Lx26f5-8rKJ3RXeh-w@mail.gmail.com/
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240409154253.3043822-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the common code from sc16is7xx driver and move the I2C and SPI bus
parts into interface-specific source files.
sc16is7xx becomes the core functions which can support multiple bus
interfaces like I2C and SPI.
No functional changes intended.
Also simplify and improve Kconfig entries.
- Capitalize SPI keyword for consistency
- Display list of supported ICs each on a separate line (and aligned) to
facilitate locating a specific IC model
- Add Manufacturer name at start of description string
- Add UART keyword to description string
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240409154253.3043822-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to check for previous port registration in
sc16is7xx_remove() because if sc16is7xx_probe() succeeded, we are
guaranteed to have successfully registered both ports. We can thus
unconditionally clear the line allocation bit in sc16is7xx_lines.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240409154253.3043822-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace incorrect include with the proper one for sched_set_fifo()
declaration.
Fixes: 28d2f209cd ("sched,serial: Convert to sched_set_fifo()")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240409154253.3043822-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case that no RTS GPIO is available do not use a dedicated nullified
serial_rs485 struct to disable RS485 support, but simply delete the
SER_RS485_ENABLED flag in the ports rs485_supported struct.
This make the structure superfluous and it can be removed.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240407002709.16224-5-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core already checks the RS485 RTS settings for sanity, so remove
the superfluous check in serial8250_em485_config().
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240407002709.16224-4-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable dmacr is only used if DMA is enabled, so move it into the
CONFIG_DMA_ENGINE conditional.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240407002709.16224-3-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to earlier code changes function pl011_get_rs485_mode() is now merely
a wrapper for uart_get_rs485_mode() which does not add any further
functionality. So remove it and instead call uart_get_rs485_mode()
directly.
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240407002709.16224-2-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using container_of() explicitly, introduce a helper macro.
This saves a lot of lines of code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240409144721.638326-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SIMPLE_DEV_PM_OPS() is deprecated, replace it with the
DEFINE_SIMPLE_DEV_PM_OPS() and use pm_sleep_ptr() for setting
the driver's PM routines.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240409144721.638326-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MODULE_ALIAS() in most cases is a pure hack to avoid placing ID tables.
Replace it with the respective ID tables.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240409144721.638326-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct uart_port has a copy of the IRQ that is also stored
in the private data structure. Remove the duplication in the latter
one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240409144721.638326-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The circular buffer is NULLified in uart_tty_port_shutdown()
under the spin lock. However, the PM or other timer based callbacks
may still trigger after this event without knowning that buffer pointer
is not valid. Since the serial code is a bit inconsistent in checking
the buffer state (some rely on the head-tail positions, some on the
buffer pointer), it's better to have both aligned, i.e. buffer pointer
to be NULL and head-tail possitions to be the same, meaning it's empty.
This will prevent asynchronous calls to dereference NULL pointer as
reported recently in 8250 case:
BUG: kernel NULL pointer dereference, address: 00000cf5
Workqueue: pm pm_runtime_work
EIP: serial8250_tx_chars (drivers/tty/serial/8250/8250_port.c:1809)
...
? serial8250_tx_chars (drivers/tty/serial/8250/8250_port.c:1809)
__start_tx (drivers/tty/serial/8250/8250_port.c:1551)
serial8250_start_tx (drivers/tty/serial/8250/8250_port.c:1654)
serial_port_runtime_suspend (include/linux/serial_core.h:667 drivers/tty/serial/serial_port.c:63)
__rpm_callback (drivers/base/power/runtime.c:393)
? serial_port_remove (drivers/tty/serial/serial_port.c:50)
rpm_suspend (drivers/base/power/runtime.c:447)
The proposed change will prevent ->start_tx() to be called during
suspend on shut down port.
Fixes: 43066e3222 ("serial: port: Don't suspend if the port is still busy")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202404031607.2e92eebe-lkp@intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240404150034.41648-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: wangkaiyuan <wangkaiyuan@inspur.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240318064216.1765-1-wangkaiyuan@inspur.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: wangkaiyuan <wangkaiyuan@inspur.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240318064036.1656-1-wangkaiyuan@inspur.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mitigation was intended to stop the irq completely. That may be
better than a hard lock-up but it turns out that you get a crash anyway
if you're using pmac_zilog as a serial console:
ttyPZ0: pmz: rx irq flood !
BUG: spinlock recursion on CPU#0, swapper/0
That's because the pr_err() call in pmz_receive_chars() results in
pmz_console_write() attempting to lock a spinlock already locked in
pmz_interrupt(). With CONFIG_DEBUG_SPINLOCK=y, this produces a fatal
BUG splat. The spinlock in question is the one in struct uart_port.
Even when it's not fatal, the serial port rx function ceases to work.
Also, the iteration limit doesn't play nicely with QEMU, as can be
seen in the bug report linked below.
A web search for other reports of the error message "pmz: rx irq flood"
didn't produce anything. So I don't think this code is needed any more.
Remove it.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@kernel.org
Cc: linux-m68k@lists.linux-m68k.org
Link: https://github.com/vivier/qemu-m68k/issues/44
Link: https://lore.kernel.org/all/1078874617.9746.36.camel@gaston/
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@kernel.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/e853cf2c762f23101cd2ddec0cc0c2be0e72685f.1712568223.git.fthain@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver complains that PCI IDs are not needed for some of the LAVA cards:
[ 0.297252] serial 0000:04:00.0: Redundant entry in serial pci_table.
[ 0.297252] Please send the output of lspci -vv, this
[ 0.297252] message (0x1407,0x0120,0x0000,0x0000), the
[ 0.297252] manufacturer and name of serial board or
[ 0.297252] modem board to <linux-serial@vger.kernel.org>.
Do as suggested.
Reported-by: Jimmy A <jimand04@hotmail.com>
Closes: https://lore.kernel.org/r/VI1P194MB052751BE157EFE9CEAB75725CE362@VI1P194MB0527.EURP194.PROD.OUTLOOK.COM
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240403224152.945099-1-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 45a3a8ef81 ("serial: core: Revert checks for tx runtime PM state")
caused a regression for Sun Ultra 60 for the sunsab driver as reported by
Nick Bowler <nbowler@draconx.ca>.
We need to add back the check runtime PM enabled state for serial port
controller device, I wrongly assumed earlier we could just remove it.
Fixes: 45a3a8ef81 ("serial: core: Revert checks for tx runtime PM state")
Cc: stable <stable@kernel.org>
Reported-by: Nick Bowler <nbowler@draconx.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240325071649.27040-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart_handle_cts_change() function in serial_core expects the caller
to hold uport->lock. For example, I have seen the below kernel splat,
when the Bluetooth driver is loaded on an i.MX28 board.
[ 85.119255] ------------[ cut here ]------------
[ 85.124413] WARNING: CPU: 0 PID: 27 at /drivers/tty/serial/serial_core.c:3453 uart_handle_cts_change+0xb4/0xec
[ 85.134694] Modules linked in: hci_uart bluetooth ecdh_generic ecc wlcore_sdio configfs
[ 85.143314] CPU: 0 PID: 27 Comm: kworker/u3:0 Not tainted 6.6.3-00021-gd62a2f068f92 #1
[ 85.151396] Hardware name: Freescale MXS (Device Tree)
[ 85.156679] Workqueue: hci0 hci_power_on [bluetooth]
(...)
[ 85.191765] uart_handle_cts_change from mxs_auart_irq_handle+0x380/0x3f4
[ 85.198787] mxs_auart_irq_handle from __handle_irq_event_percpu+0x88/0x210
(...)
Cc: stable@vger.kernel.org
Fixes: 4d90bb147e ("serial: core: Document and assert lock requirements for irq helpers")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240320121530.11348-1-emil.kronborg@protonmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e5d6bd25f9 ("serial: 8250_dw: Do not reclock if already at
correct rate") breaks the dw UARTs on Intel Bay Trail (BYT) and
Cherry Trail (CHT) SoCs.
Before this change the RTL8732BS Bluetooth HCI which is found
connected over the dw UART on both BYT and CHT boards works properly:
Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_fw.bin
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_config-OBDA8723.bin
Bluetooth: hci0: RTL: cfg_sz 64, total sz 24508
Bluetooth: hci0: RTL: fw version 0x365d462e
where as after this change probing it fails:
Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_fw.bin
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_config-OBDA8723.bin
Bluetooth: hci0: RTL: cfg_sz 64, total sz 24508
Bluetooth: hci0: command 0xfc20 tx timeout
Bluetooth: hci0: RTL: download fw command failed (-110)
Revert the changes to fix this regression.
Fixes: e5d6bd25f9 ("serial: 8250_dw: Do not reclock if already at correct rate")
Cc: stable@vger.kernel.org
Cc: Peter Collingbourne <pcc@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Peter Collingbourne <pcc@google.com>
Link: https://lore.kernel.org/r/20240317214123.34482-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Goto the clean up path to clean up a couple clocks before returning
on this error path.
Fixes: 0087b9e694 ("serial: 8250_lpc18xx: Switch to use uart_read_port_properties()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/92646c10-e0b5-4117-a9ac-ce9987d33ce3@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no code using max3100_work() before the definition of it.
Remove unneeded forward declaration.
While at it, move max3100_dowork() and max3100_timeout() down in
the code to be after actual max3100_work() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-15-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While there is no user of this callback in the kernel, it also breaks
the relationship in the driver model. The correct implementation should
be done via GPIO or regulator framework.
Remove custom HW shutdown support for good and, if needed, we will
implement it correctly later on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no user of the struct plat_max3100 outside the driver.
Inline its contents into the driver. While at it, drop outdated
example in the comment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse is not happy about misuse of bitwise types:
.../max3100.c:194:13: warning: incorrect type in assignment (different base types)
.../max3100.c:194:13: expected unsigned short [addressable] [usertype] etx
.../max3100.c:194:13: got restricted __be16 [usertype]
.../max3100.c:202:15: warning: cast to restricted __be16
Fix this by choosing proper types for the respective variables.
Fixes: 7831d56b0a ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The removal of the last MAX3100 device triggers the removal of
the driver. However, code doesn't update the respective global
variable and after insmod — rmmod — insmod cycle the kernel
oopses:
max3100 spi-PRP0001:01: max3100_probe: adding port 0
BUG: kernel NULL pointer dereference, address: 0000000000000408
...
RIP: 0010:serial_core_register_port+0xa0/0x840
...
max3100_probe+0x1b6/0x280 [max3100]
spi_probe+0x8d/0xb0
Update the actual state so next time UART driver will be registered
again.
Hugo also noticed, that the error path in the probe also affected
by having the variable set, and not cleared. Instead of clearing it
move the assignment after the successfull uart_register_driver() call.
Fixes: 7831d56b0a ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240402195306.269276-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_handle_cts_change() has to be called with port lock taken,
Since we run it in a separate work, the lock may not be taken at
the time of running. Make sure that it's taken by explicitly doing
that. Without it we got a splat:
WARNING: CPU: 0 PID: 10 at drivers/tty/serial/serial_core.c:3491 uart_handle_cts_change+0xa6/0xb0
...
Workqueue: max3100-0 max3100_work [max3100]
RIP: 0010:uart_handle_cts_change+0xa6/0xb0
...
max3100_handlerx+0xc5/0x110 [max3100]
max3100_work+0x12a/0x340 [max3100]
Fixes: 7831d56b0a ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART's input clock rate can change at runtime but this is not
handled by the driver.
Add a clock_notifier callback that updates the divisors when the input
clock is updated. The serial8250_update_uartclk() is used to do so.
PRE_RATE_CHANGE and ABORT_RATE_CHANGE notifications are ignored, only
the POST_RATE_CHANGE is used. Not using PRE_RATE_CHANGE notification can
result in a few corrupted bytes during frequency transitions but, IMHO,
it can be acceptable in many use cases.
It has been tested on a DAVINCI/OMAP-L138 processor.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20240405120552.35991-1-bastien.curutchet@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are considerations to drop platform_driver_probe() as a concept
that isn't relevant any more today. It comes with an added complexity
that makes many users hold it wrong. (E.g. this driver should have
marked the driver struct with __refdata to prevent the below mentioned
false positive section mismatch warning.)
This fixes a W=1 build warning:
WARNING: modpost: drivers/tty/serial/pmac_zilog: section mismatch in reference: pmz_driver+0x8 (section: .data) -> pmz_detach (section: .exit.text)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5ea3174616abc9fa256f115b4fb175d289ac1754.1711748999.git.u.kleine-koenig@pengutronix.de
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver is using "sifive,fu540-c000-uart0" as a binding. The device
tree and documentation states "sifive,fu540-c000-uart" instead. This
means the binding is not matched and not used.
This did not cause any problems because the alternative binding, used in
the device tree, "sifive,uart0" is not handling the hardware any
different.
Align the binding in the driver with the documentation.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240307090950.eLELkuyK@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it directly, replace it
with what is really being used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240307114243.3642832-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
