esp32s3 variant of the esp32 UART has limited baudrate divisor range
that does not allow it to use 9600 and lower rates with 40MHz input
clock. Use clock prescaler present in this UART variant to help with
that.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20231018191252.1551972-1-jcmvbkbc@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AR7 is going to be removed from the Kernel, so remove its type
definition from 8250 code. As with previous removals, I checked with
Debian Code Search that 'PORT_AR7' is not used in userspace.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
uart_get_baud_rate has input parameters 'min' and 'max' limiting the
range of acceptable baud rates from the caller's perspective. If neither
current or old termios structures have acceptable baud rate setting and
9600 is not in the min/max range either the function returns 0 and
issues a warning.
However for a UART that does not support speed of 9600 baud this is
expected behavior.
Clarify that 0 can be (and always could be) returned from the
uart_get_baud_rate. Don't issue a warning in that case.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20231010085926.1021667-2-jcmvbkbc@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zynq UG585 states, in chapter B.33, for XUARTPS_CR_STARTBRK:
It can only be set if STPBRK (Stop transmitter break) is not high
This fixes tcsendbreak, which otherwise does not actually break.
Signed-Off-By: Julien Malik <julien.malik@unseenlabs.fr>
Link: https://lore.kernel.org/r/20230624210323.88455-1-julien.malik@unseenlabs.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the tty/serial fixes in here as well for testing, and this
resolves merge conflicts in:
drivers/tty/serial/serial_core.c
as reported in linux-next
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new Amlogic S4 SoC does not have a always-on uart, so add
OF_EARLYCON_DECLARE for it.
Amlogic T7 will use this as fallback.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231009121151.4509-1-tanure@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maximilian reported that surface_serial_hub serdev tx does not work during
system suspend. During system suspend, runtime PM gets disabled in
__device_suspend_late(), and tx is unable to wake-up the serial core port
device that we use to check if tx is safe to start. Johan summarized the
regression noting that serdev tx no longer always works as earlier when the
serdev device is runtime PM active.
The serdev device and the serial core controller devices are siblings of
the serial port hardware device. The runtime PM usage count from serdev
device does not propagate to the serial core device siblings, it only
propagates to the parent.
In addition to the tx issue for suspend, testing for the serial core port
device can cause an unnecessary delay in enabling tx while waiting for the
serial core port device to wake-up. The serial core port device wake-up is
only needed to flush pending tx when the serial port hardware device was
in runtime PM suspended state.
To fix the regression, we need to check the runtime PM state of the parent
serial port hardware device for tx instead of the serial core port device.
As the serial port device drivers may or may not implement runtime PM, we
need to also add a check for pm_runtime_enabled().
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: stable <stable@kernel.org>
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231005075644.25936-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this check ever triggers
static int uart_get_info(struct tty_port *port, struct serial_struct *retinfo)
{
uport = uart_port_check(state);
if (!uport)
goto out;
then all those sysfs users will print stack contents to userspace.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Link: https://lore.kernel.org/r/967b9ef1-fb36-48bf-9e6a-1b99af24c052@p183
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify uart_get_rs485_mode() by using temporary variable for
the GPIO descriptor. With that, use proper type for the flags
of the GPIO descriptor.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231003142346.3072929-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's drop the use of pm_runtime_irq_safe() for 8250_omap. The use of
pm_runtime_irq_safe() is not nice as it takes a permanent usage count on
the parent device.
We can finally drop pm_runtime_irq_safe() safely as the kernel now knows
when the uart port tx is active. This changed with commit 84a9582fd2
("serial: core: Start managing serial controllers to enable runtime PM").
For serial port rx, we already use Linux generic wakeirqs for 8250_omap.
To drop pm_runtime_irq_safe(), we need to add handling for shallow idle
state where the port hardware may already be awake and an IO interrupt
happens. We also need to replace the serial8250_rpm sync calls in the
interrupt handlers with async runtime PM calls.
Note that omap8250_irq() calls omap_8250_dma_handle_irq(), so we don't
need separate runtime PM calls in omap_8250_dma_handle_irq().
While at it, let's also add the missing line break to the end of
omap8250_runtime_resume() to group the calls.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231004062650.64487-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We now get errors on system suspend if no_console_suspend is set as
reported by Thomas. The errors started with commit 20a41a6261 ("serial:
8250_omap: Use force_suspend and resume for system suspend").
Let's fix the issue by checking for console_suspend_enabled in the system
suspend and resume path.
Note that with this fix the checks for console_suspend_enabled in
omap8250_runtime_suspend() become useless. We now keep runtime PM usage
count for an attached kernel console starting with commit bedb404e91
("serial: 8250_port: Don't use power management for kernel console").
Fixes: 20a41a6261 ("serial: 8250_omap: Use force_suspend and resume for system suspend")
Cc: stable <stable@kernel.org>
Cc: Udit Kumar <u-kumar1@ti.com>
Reported-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230926061319.15140-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 44b27aec9d ("serial: core, 8250: set RS485 termination GPIO in
serial core") enabled support for RS485 termination GPIOs behind i2c
expanders by setting the GPIO outside of the critical section protected
by the port spinlock. Access to the i2c expander may sleep, which
caused a splat with the port spinlock held.
Commit 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in
driver-specific way") erroneously regressed that by spinlocking the
GPIO manipulation again.
Fix by moving uart_rs485_config() (the function manipulating the GPIO)
outside of the spinlocked section and acquiring the spinlock inside of
uart_rs485_config() for the invocation of ->rs485_config() only.
This gets us one step closer to pushing the spinlock down into the
->rs485_config() callbacks which actually need it. (Some callbacks
do not want to be spinlocked because they perform sleepable register
accesses, see e.g. sc16is7xx_config_rs485().)
Stack trace for posterity:
Voluntary context switch within RCU read-side critical section!
WARNING: CPU: 0 PID: 56 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch
Call trace:
rcu_note_context_switch
__schedule
schedule
schedule_timeout
wait_for_completion_timeout
bcm2835_i2c_xfer
__i2c_transfer
i2c_transfer
i2c_transfer_buffer_flags
regmap_i2c_write
_regmap_raw_write_impl
_regmap_bus_raw_write
_regmap_write
_regmap_update_bits
regmap_update_bits_base
pca953x_gpio_set_value
gpiod_set_raw_value_commit
gpiod_set_value_nocheck
gpiod_set_value_cansleep
uart_rs485_config
uart_add_one_port
pl011_register_port
pl011_probe
Fixes: 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Suggested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.1+
Link: https://lore.kernel.org/r/f3a35967c28b32f3c6432d0aa5936e6a9908282d.1695307688.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert driver to be property provider agnostic and allow it to be
used on non-OF platforms.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230927160153.2717788-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many SoCs do not integrate DMA for the amba pl011 UART, causing
the following message on boot:
uart-pl011 80074000.serial: no DMA platform data
The UART still works in PIO, so better not to print such message that
may confuse people by causing them to think that there is something wrong
with the UART.
Change the message to debug level.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20230928145842.466933-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lockdep complains about possible circular locking dependencies when the
i.MX SDMA driver issues console messages under its spinlock. While the
SDMA driver calls back into the UART when issuing a message, the i.MX
UART driver will never call back into the SDMA driver for this UART,
because DMA is explicitly not used for UARTs providing the console.
To avoid the lockdep warnings put the UART port lock for console devices
into a separate subclass.
This fixes possible deadlock warnings like the following which was
provoked by adding a printk to the i.MX SDMA driver at a place where the
driver holds its spinlock.
======================================================
WARNING: possible circular locking dependency detected
6.6.0-rc3-00045-g517852be693b-dirty #110 Not tainted
------------------------------------------------------
swapper/0/0 is trying to acquire lock:
c1818e04 (console_owner){-...}-{0:0}, at: console_flush_all+0x1c4/0x634
but task is already holding lock:
c44649e0 (&vc->lock){-...}-{3:3}, at: sdma_int_handler+0xc4/0x368
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&vc->lock){-...}-{3:3}:
_raw_spin_lock_irqsave+0x4c/0x68
sdma_prep_dma_cyclic+0x1a8/0x21c
imx_uart_startup+0x44c/0x5d4
uart_startup+0x120/0x2b0
uart_port_activate+0x44/0x98
tty_port_open+0x80/0xd0
uart_open+0x18/0x20
tty_open+0x120/0x664
chrdev_open+0xc0/0x214
do_dentry_open+0x1d0/0x544
path_openat+0xbb0/0xea0
do_filp_open+0x5c/0xd4
do_sys_openat2+0xb8/0xf0
sys_openat+0x8c/0xd8
ret_fast_syscall+0x0/0x1c
-> #1 (&port_lock_key){-.-.}-{3:3}:
_raw_spin_lock_irqsave+0x4c/0x68
imx_uart_console_write+0x164/0x1a0
console_flush_all+0x220/0x634
console_unlock+0x64/0x164
vprintk_emit+0xb0/0x390
vprintk_default+0x24/0x2c
_printk+0x2c/0x5c
register_console+0x244/0x478
serial_core_register_port+0x5c4/0x618
imx_uart_probe+0x4e0/0x7d4
platform_probe+0x58/0xb0
really_probe+0xc4/0x2e0
__driver_probe_device+0x84/0x1a0
driver_probe_device+0x2c/0x108
__driver_attach+0x94/0x17c
bus_for_each_dev+0x7c/0xd0
bus_add_driver+0xc4/0x1cc
driver_register+0x7c/0x114
imx_uart_init+0x20/0x40
do_one_initcall+0x7c/0x3c4
kernel_init_freeable+0x17c/0x228
kernel_init+0x14/0x140
ret_from_fork+0x14/0x24
-> #0 (console_owner){-...}-{0:0}:
__lock_acquire+0x14b0/0x29a0
lock_acquire.part.0+0xb4/0x264
console_flush_all+0x20c/0x634
console_unlock+0x64/0x164
vprintk_emit+0xb0/0x390
vprintk_default+0x24/0x2c
_printk+0x2c/0x5c
sdma_int_handler+0xcc/0x368
__handle_irq_event_percpu+0x94/0x2d0
handle_irq_event+0x38/0xd0
handle_fasteoi_irq+0x98/0x248
handle_irq_desc+0x1c/0x2c
gic_handle_irq+0x6c/0x90
generic_handle_arch_irq+0x2c/0x64
__irq_svc+0x90/0xbc
cpuidle_enter_state+0x1a0/0x4f4
cpuidle_enter+0x30/0x40
do_idle+0x210/0x2b4
cpu_startup_entry+0x28/0x2c
rest_init+0xd0/0x184
arch_post_acpi_subsys_init+0x0/0x8
other info that might help us debug this:
Chain exists of:
console_owner --> &port_lock_key --> &vc->lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&vc->lock);
lock(&port_lock_key);
lock(&vc->lock);
lock(console_owner);
*** DEADLOCK ***
3 locks held by swapper/0/0:
#0: c44649e0 (&vc->lock){-...}-{3:3}, at: sdma_int_handler+0xc4/0x368
#1: c1818d50 (console_lock){+.+.}-{0:0}, at: vprintk_default+0x24/0x2c
#2: c1818d08 (console_srcu){....}-{0:0}, at: console_flush_all+0x44/0x634
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.6.0-rc3-00045-g517852be693b-dirty #110
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x60/0x90
dump_stack_lvl from check_noncircular+0x184/0x1b8
check_noncircular from __lock_acquire+0x14b0/0x29a0
__lock_acquire from lock_acquire.part.0+0xb4/0x264
lock_acquire.part.0 from console_flush_all+0x20c/0x634
console_flush_all from console_unlock+0x64/0x164
console_unlock from vprintk_emit+0xb0/0x390
vprintk_emit from vprintk_default+0x24/0x2c
vprintk_default from _printk+0x2c/0x5c
_printk from sdma_int_handler+0xcc/0x368
sdma_int_handler from __handle_irq_event_percpu+0x94/0x2d0
__handle_irq_event_percpu from handle_irq_event+0x38/0xd0
handle_irq_event from handle_fasteoi_irq+0x98/0x248
handle_fasteoi_irq from handle_irq_desc+0x1c/0x2c
handle_irq_desc from gic_handle_irq+0x6c/0x90
gic_handle_irq from generic_handle_arch_irq+0x2c/0x64
generic_handle_arch_irq from __irq_svc+0x90/0xbc
Exception stack(0xc1801ee8 to 0xc1801f30)
1ee0: ffffffff ffffffff 00000001 00030349 00000000 00000012
1f00: 00000000 d7e45f4b 00000012 00000000 d7e16d63 c1810828 00000000 c1801f38
1f20: c108125c c1081260 60010013 ffffffff
__irq_svc from cpuidle_enter_state+0x1a0/0x4f4
cpuidle_enter_state from cpuidle_enter+0x30/0x40
cpuidle_enter from do_idle+0x210/0x2b4
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from rest_init+0xd0/0x184
rest_init from arch_post_acpi_subsys_init+0x0/0x8
Reported-by: Tim van der Staaij <Tim.vanderstaaij@zigngroup.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20230928064320.711603-1-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct pci1xxxx_8250.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Cc: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922175242.work.442-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sealevel XR17V35X based cards utilize DTR to control RS-485 Enable, but
the current implementation of 8250_exar uses RTS for the auto-RS485-Enable
mode of the XR17V35X UARTs. This patch implements DTR Auto-RS485 on
Sealevel cards.
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenkoa@linux.intel.com>
Link: https://lore.kernel.org/r/4b8ad8ab6728742464c4e048fdeecb2b40522aef.camel@sealevel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_clk_get_optional_enabled() to simplify the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230919195513.3197930-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the error messages format unified by switching to use
dev_err_probe() where it makes sense.
This also helps simplifing the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230918103648.1185663-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-75-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-74-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-73-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-72-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-71-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-70-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-69-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-68-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-67-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-66-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-65-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-64-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-63-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-62-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-61-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-60-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-59-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-58-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-57-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-56-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-55-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-54-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-53-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-52-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-51-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-50-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-49-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-48-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-47-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-46-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-45-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-44-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-43-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-42-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-41-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-40-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-39-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-38-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-37-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-36-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-35-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-34-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-33-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-32-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-31-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-30-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-29-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-28-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-27-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-26-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-25-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-24-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-23-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-22-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-21-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-20-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-19-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-18-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-17-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-16-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-15-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-14-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-13-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-12-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-11-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-10-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-9-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-8-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-7-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-6-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-5-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-4-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Three of the four entries of imx_uart_devdata[] use .uts_reg =
IMX21_UTS. The difference in the .devtype member isn't relevant, the
only thing that matters is if is equal to IMX1_UART.
So use an entry with .devtype = IMX21_UART on all platforms but i.MX1.
There is no need to have the dev types in an array, so split them up in
two separate variables.
The fsl,imx53-uart devinfo can go away because in the binding and also
the dts files all fsl,imx53-uart devices also are compatible to
fsl,imx21-uart. That's not the case for fsl,imx6q-uart (which is a bit
strange IMHO), so the fsl,imx6q-uart must stay around.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230911085451.628798-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace 740/750/760 with generic terms like 74x/75x/76x to account for
variants like 741, 752 and 762.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230905151300.15365-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform_get_irq might be failed and return a negative result. So
there should have an error handling code.
Fixed this by adding an error handling code.
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Link: https://lore.kernel.org/r/tencent_234B0AACD06350E10D7548C2E086A9166305@qq.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sort drivers in alphabetic order in Makefile to make it easier to find
the correct line. In case the CONFIG and filenames disagree, sort using
the filename (ignore 8250 prefix while sorting).
In addition, place 8250_early separately above the drivers.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230912103558.20123-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sort drivers in alphabetic order in Makefile to make it easier to find
the correct line. In case the CONFIG and filenames disagree, sort using
the filename (but ignoring "serial" prefixes).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230912103558.20123-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_exar includes linux/8250_pci.h and depends on SERIAL_8250_PCI.
Neither is necessary so this patch removes the include and changes
the depends on to SERIAL_8250 && PCI (taken from SERIAL_8250_PCI).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230915094336.13278-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_mid uses FL_*BASE* from linux/8250_pci.h and nothing else. The
code can be simplified by directly defining BARs within the driver
instead.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230915094336.13278-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe process may generate EPROBE_DEFER. In this case
dev_err_probe() can still record err information. Otherwise
it may pollute logs on that occasion.
This also helps simplifing code and standardizing the error output.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230912165607.402580-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe process may generate EPROBE_DEFER. In this case
dev_err_probe() can still record err information. Otherwise
it may pollute logs on that occasion.
This also helps simplifing code and standardizing the error output.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230912165540.402504-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART_IIR_64BYTE_FIFO is always being used in conjunction with
UART_IIR_FIFO_ENABLED. Introduce a joined UART_IIR_FIFO_ENABLED_16750
definition and use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230911144308.4169752-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for break control to the stm32 serial driver.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230906151547.840302-1-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This macro is not used anywhere.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230905181649.134720-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add check for ioremap() and return the error if it fails in order to
guarantee the success of ioremap().
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Acked-by: Jacky Huang <ychuang3@nuvoton.com>
Link: https://lore.kernel.org/r/20230915071106.3347-1-nichen@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the leaf driver wants to use IRQ polling (irq = 0) and
IIR register shows that an interrupt happened in the 8250 hardware
the IRQ data can be NULL. In such a case we need to skip the wake
event as we came to this path from the timer interrupt and quite
likely system is already awake.
Without this fix we have got an Oops:
serial8250: ttyS0 at I/O 0x3f8 (irq = 0, base_baud = 115200) is a 16550A
...
BUG: kernel NULL pointer dereference, address: 0000000000000010
RIP: 0010:serial8250_handle_irq+0x7c/0x240
Call Trace:
? serial8250_handle_irq+0x7c/0x240
? __pfx_serial8250_timeout+0x10/0x10
Fixes: 0ba9e3a13c ("serial: 8250: Add missing wakeup event reporting")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230831222555.614426-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Itanium architecture is obsolete, and an informal survey [0] reveals
that any residual use of Itanium hardware in production is mostly HP-UX
or OpenVMS based. The use of Linux on Itanium appears to be limited to
enthusiasts that occasionally boot a fresh Linux kernel to see whether
things are still working as intended, and perhaps to churn out some
distro packages that are rarely used in practice.
None of the original companies behind Itanium still produce or support
any hardware or software for the architecture, and it is listed as
'Orphaned' in the MAINTAINERS file, as apparently, none of the engineers
that contributed on behalf of those companies (nor anyone else, for that
matter) have been willing to support or maintain the architecture
upstream or even be responsible for applying the odd fix. The Intel
firmware team removed all IA-64 support from the Tianocore/EDK2
reference implementation of EFI in 2018. (Itanium is the original
architecture for which EFI was developed, and the way Linux supports it
deviates significantly from other architectures.) Some distros, such as
Debian and Gentoo, still maintain [unofficial] ia64 ports, but many have
dropped support years ago.
While the argument is being made [1] that there is a 'for the common
good' angle to being able to build and run existing projects such as the
Grid Community Toolkit [2] on Itanium for interoperability testing, the
fact remains that none of those projects are known to be deployed on
Linux/ia64, and very few people actually have access to such a system in
the first place. Even if there were ways imaginable in which Linux/ia64
could be put to good use today, what matters is whether anyone is
actually doing that, and this does not appear to be the case.
There are no emulators widely available, and so boot testing Itanium is
generally infeasible for ordinary contributors. GCC still supports IA-64
but its compile farm [3] no longer has any IA-64 machines. GLIBC would
like to get rid of IA-64 [4] too because it would permit some overdue
code cleanups. In summary, the benefits to the ecosystem of having IA-64
be part of it are mostly theoretical, whereas the maintenance overhead
of keeping it supported is real.
So let's rip off the band aid, and remove the IA-64 arch code entirely.
This follows the timeline proposed by the Debian/ia64 maintainer [5],
which removes support in a controlled manner, leaving IA-64 in a known
good state in the most recent LTS release. Other projects will follow
once the kernel support is removed.
[0] https://lore.kernel.org/all/CAMj1kXFCMh_578jniKpUtx_j8ByHnt=s7S+yQ+vGbKt9ud7+kQ@mail.gmail.com/
[1] https://lore.kernel.org/all/0075883c-7c51-00f5-2c2d-5119c1820410@web.de/
[2] https://gridcf.org/gct-docs/latest/index.html
[3] https://cfarm.tetaneutral.net/machines/list/
[4] https://lore.kernel.org/all/87bkiilpc4.fsf@mid.deneb.enyo.de/
[5] https://lore.kernel.org/all/ff58a3e76e5102c94bb5946d99187b358def688a.camel@physik.fu-berlin.de/
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
("refactor Kconfig to consolidate KEXEC and CRASH options").
- kernel.h slimming work from Andy Shevchenko ("kernel.h: Split out a
couple of macros to args.h").
- gdb feature work from Kuan-Ying Lee ("Add GDB memory helper
commands").
- vsprintf inclusion rationalization from Andy Shevchenko
("lib/vsprintf: Rework header inclusions").
- Switch the handling of kdump from a udev scheme to in-kernel handling,
by Eric DeVolder ("crash: Kernel handling of CPU and memory hot
un/plug").
- Many singleton patches to various parts of the tree
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZO2GpAAKCRDdBJ7gKXxA
juW3AQD1moHzlSN6x9I3tjm5TWWNYFoFL8af7wXDJspp/DWH/AD/TO0XlWWhhbYy
QHy7lL0Syha38kKLMXTM+bN6YQHi9AU=
=WJQa
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2023-08-28-22-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- An extensive rework of kexec and crash Kconfig from Eric DeVolder
("refactor Kconfig to consolidate KEXEC and CRASH options")
- kernel.h slimming work from Andy Shevchenko ("kernel.h: Split out a
couple of macros to args.h")
- gdb feature work from Kuan-Ying Lee ("Add GDB memory helper
commands")
- vsprintf inclusion rationalization from Andy Shevchenko
("lib/vsprintf: Rework header inclusions")
- Switch the handling of kdump from a udev scheme to in-kernel
handling, by Eric DeVolder ("crash: Kernel handling of CPU and memory
hot un/plug")
- Many singleton patches to various parts of the tree
* tag 'mm-nonmm-stable-2023-08-28-22-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (81 commits)
document while_each_thread(), change first_tid() to use for_each_thread()
drivers/char/mem.c: shrink character device's devlist[] array
x86/crash: optimize CPU changes
crash: change crash_prepare_elf64_headers() to for_each_possible_cpu()
crash: hotplug support for kexec_load()
x86/crash: add x86 crash hotplug support
crash: memory and CPU hotplug sysfs attributes
kexec: exclude elfcorehdr from the segment digest
crash: add generic infrastructure for crash hotplug support
crash: move a few code bits to setup support of crash hotplug
kstrtox: consistently use _tolower()
kill do_each_thread()
nilfs2: fix WARNING in mark_buffer_dirty due to discarded buffer reuse
scripts/bloat-o-meter: count weak symbol sizes
treewide: drop CONFIG_EMBEDDED
lockdep: fix static memory detection even more
lib/vsprintf: declare no_hash_pointers in sprintf.h
lib/vsprintf: split out sprintf() and friends
kernel/fork: stop playing lockless games for exe_file replacement
adfs: delete unused "union adfs_dirtail" definition
...
This reverts commit 6a4197f976
New SoC will use ttyS0 instead of ttyAML, so T7 SoC doesn't need a
OF_EARLYCON_DECLARE.
Fixes: 6a4197f976 ("tty: serial: meson: Add a earlycon for the T7 SoC")
Signed-off-by: Lucas Tanure <tanure@linux.com>
Link: https://lore.kernel.org/r/20230827082944.5100-1-tanure@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 BCM7271 UART is not a direct match to PORT_16550A and other
generic ports do not match its hardware capabilities. PORT_ALTR matches
the rx trigger levels, but its vendor configurations are not compatible.
Unfortunately this means we need to create another port to fully capture
the hardware capabilities of the BCM7271 UART.
To alleviate some latency pressures, we default the rx trigger level to 8.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/1692643978-16570-1-git-send-email-justin.chen@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retrieve rs485 devicetree properties on registration of sc16is7xx ports in
case they are attached to an rs485 transceiver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configuring a pin as an output pin with a value of logic 0, we
end up as having a value of logic 1 on the output pin. Setting a
logic 0 a second time (or more) after that will correctly output a
logic 0 on the output pin.
By default, all GPIO pins are configured as inputs. When we enter
sc16is7xx_gpio_direction_output() for the first time, we first set the
desired value in IOSTATE, and then we configure the pin as an output.
The datasheet states that writing to IOSTATE register will trigger a
transfer of the value to the I/O pin configured as output, so if the
pin is configured as an input, nothing will be transferred.
Therefore, set the direction first in IODIR, and then set the desired
value in IOSTATE.
This is what is done in NXP application note AN10587.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 679875d1d8 ("sc16is7xx: Separate GPIOs from modem control lines")
and commit 21144bab4f ("sc16is7xx: Handle modem status lines")
changed the function of the GPIOs pins to act as modem control
lines without any possibility of selecting GPIO function.
As a consequence, applications that depends on GPIO lines configured
by default as GPIO pins no longer work as expected.
Also, the change to select modem control lines function was done only
for channel A of dual UART variants (752/762). This was not documented
in the log message.
Allow to specify GPIO or modem control line function in the device
tree, and for each of the ports (A or B).
Do so by using the new device-tree property named
"nxp,modem-control-line-ports" (property added in separate patch).
When registering GPIO chip controller, mask-out GPIO pins declared as
modem control lines according to this new DT property.
Fixes: 679875d1d8 ("sc16is7xx: Separate GPIOs from modem control lines")
Fixes: 21144bab4f ("sc16is7xx: Handle modem status lines")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230807214556.540627-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c8f71b49ee ("serial: sc16is7xx: setup GPIO controller later
in probe") moved GPIO setup code later in probe function. Doing so
also required to move ports cleanup code (out_ports label) after the
GPIO cleanup code.
After these moves, the out_thread label becomes misplaced and makes
part of the cleanup code illogical.
This patch remove the now obsolete out_thread label and make GPIO
setup code jump to out_ports label if it fails.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230807214556.540627-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sc16is7xx_config_rs485() function is called only for the second
port (index 1, channel B), causing initialization problems for the
first port.
For the sc16is7xx driver, port->membase and port->mapbase are not set,
and their default values are 0. And we set port->iobase to the device
index. This means that when the first device is registered using the
uart_add_one_port() function, the following values will be in the port
structure:
port->membase = 0
port->mapbase = 0
port->iobase = 0
Therefore, the function uart_configure_port() in serial_core.c will
exit early because of the following check:
/*
* If there isn't a port here, don't do anything further.
*/
if (!port->iobase && !port->mapbase && !port->membase)
return;
Typically, I2C and SPI drivers do not set port->membase and
port->mapbase.
The max310x driver sets port->membase to ~0 (all ones). By
implementing the same change in this driver, uart_configure_port() is
now correctly executed for all ports.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there's no irq(this can be due to various reasons, for example,
no irq from HW support, or we just want to use poll solution, and so
on), falling back to poll is still better than no support at all.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20230806092056.2467-3-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In tegra_uart_hw_init(), the return value of clk_prepare_enable() should
be checked since it might fail.
Fixes: e9ea096dd2 ("serial: tegra: add serial driver")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Link: https://lore.kernel.org/r/20230817105406.228674-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the Sifive Uart is not used as the wake up source, suspend the uart
before the system enter the suspend state to prevent it woken up by
unexpected uart interrupt. Resume the uart once the system woken up.
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Reviewed-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20230815090216.2575971-1-nick.hu@sifive.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new Amlogic T7 SoC does not have a always-on uart,
so add OF_EARLYCON_DECLARE for it.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230814080128.143613-2-tanure@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In shutdown, RX DMA channel is terminated. If the DMA RX callback is
scheduled but not yet executed, while a new RX DMA transfer is started, the
callback can be executed, and then disturb the ongoing RX DMA transfer.
To avoid such a case, call dmaengine_synchronize in shutdown, after the
DMA RX channel is terminated.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-7-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's rather advised to rely on DMA pause / resume instead of
clearing/setting DMA request enable bit for the same purpose. Some DMA
request/acknowledge race may encountered by doing so. We prefer to use
dmaengine_pause and resume instead to pause a dma transfer when it is
necessary.
Create two new functions (stm32_usart_rx_dma_pause, stm32_usart_rx_dma
_resume) to handle dma error when pausing/resuming.
And rename stm32_usart_start_rx_dma_cyclic() to
stm32_usart_rx_dma_start_or_resume() and use this function to resume an
rx dma transfer. If resume fail, stm32_usart_rx_dma_start_or_resume can
create a new transfer to continue.
It is also safer to close DMA before reset DMAR in stm32_usart_shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-6-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create new function "stm32_usart_dma_pause_resume" that called dmaengine_
pause/resume and in case of error, terminate dma transaction.
Two other functions are created to facilitate the use of stm32_usart_dma
_pause_resume : stm32_usart_tx_dma_pause, stm32_usart_tx_dma_resume.
Equivalent functions for rx will be added in future patch.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-5-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename stm32_usart_rx_dma_enabled to stm32_usart_rx_dma_started in order
to match with stm32_usart_tx_dma_started.
Modify argument of stm32_usart_rx_dma_started from uart_port structure to
stm32_port structure to match with stm32_usart_tx_dma_started.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-4-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMAT is a configuration bit so it should be set at the startup of uart
port and not when a DMA transfer begins.
This patch move set of DMAT into set_termios and remove DMAT reset except
in shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's rather advised to rely on DMA pause / resume instead of
clearing/setting DMA request enable bit for the same purpose. Some DMA
request/acknowledge race may encountered by doing so. We prefer to use
dmaengine_pause and resume instead to pause a dma transfer when it is
necessary.
It is also safer to close DMA before reset DMAT in stm32_usart_shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to fix the serial core port DEVNAME to use a port id of the
hardware specific controller port instance instead of the port->line.
For example, the 8250 driver sets up a number of serial8250 ports
initially that can be inherited by the hardware specific driver. At that
the port->line no longer decribes the port's relation to the serial core
controller instance.
Let's fix the issue by assigning port->port_id for each serial core
controller port instance.
Fixes: 7d695d8376 ("serial: core: Fix serial_base_match() after fixing controller port name")
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811103648.2826-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is not always held when calling serial8250_clear_IER().
When an oops is in progress, the lock is tried to be taken and when it
is not, a warning is issued:
WARNING: CPU: 0 PID: 1 at drivers/tty/serial/8250/8250_port.c:707 +0x57/0x60
Modules linked in:
CPU: 0 PID: 1 Comm: init Not tainted 6.5.0-rc5-1.g225bfb7-default+ #774 00f1be860db663ed29479b8255d3b01ab1135bd3
Hardware name: QEMU Standard PC ...
RIP: 0010:serial8250_clear_IER+0x57/0x60
...
Call Trace:
<TASK>
serial8250_console_write+0x9e/0x4b0
console_flush_all+0x217/0x5f0
...
Therefore, remove the annotation as it doesn't hold for all invocations.
The other option would be to make the lockdep test conditional on
'oops_in_progress' or pass 'locked' from serial8250_console_write(). I
don't think, that is worth it.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Cc: John Ogness <john.ogness@linutronix.de>
Fixes: d0b309a5d3 (serial: 8250: synchronize and annotate UART_IER access)
Link: https://lore.kernel.org/r/20230811064340.13400-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TX is handled by primary sequencer. After cancelling primary command, poll
primary sequencer's irq status instead of that of secondary.
While at it, also remove a couple of redundant lines that read from IRQ_EN
register and write back same.
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Link: https://lore.kernel.org/r/1691578393-9891-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter reports boot issues with duplicate sysfs entries for multiport
drivers. Let's go back to using port->line for now to fix the regression.
With this change, the serial core port device names are not correct for the
hardware specific 8250 single port drivers, but that's a cosmetic issue for
now.
Fixes: d962de6ae5 ("serial: core: Fix serial core port id to not use port->line")
Reported-by: Guenter Roeck <groeck7@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230806062052.47737-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unloading a hardware specific 8250 driver can produce error "Unable to
handle kernel paging request at virtual address" about ten seconds after
unloading the driver. This happens on uart_hangup() calling
uart_change_pm().
Turns out commit 04e82793f0 ("serial: 8250: Reinit port->pm on port
specific driver unbind") was only a partial fix. If the hardware specific
driver has initialized port->pm function, we need to clear port->pm too.
Just reinitializing port->ops does not do this. Otherwise serial8250_pm()
will call port->pm() instead of serial8250_do_pm().
Fixes: 04e82793f0 ("serial: 8250: Reinit port->pm on port specific driver unbind")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230804131553.52927-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After fixing the serial core port device to use port->port_id instead of
port->line, unloading a hardware specific 8250 port driver started
producing an error for "sysfs: cannot create duplicate filename".
This is happening as we are wrongly initializing port->port_id to zero
when adding back serial8250_isa_devs instances, and the serial8250:0.0
sysfs entry may already exist. For serial8250 devices, we typically have
multiple devices mapped to a single driver instance. For the
serial8250_isa_devs instances, the port->port_id is the same as port->line.
Let's fix the issue by re-initializing port_id when adding back the
serial8250_isa_devs instances in serial8250_unregister_port().
Fixes: d962de6ae5 ("serial: core: Fix serial core port id to not use port->line")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230804123546.25293-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kmemleak reports issues for serial8250 ports after the hardware specific
driver takes over on boot as noted by Tomi.
The kerneldoc for device_initialize() says we must call device_put()
after calling device_initialize(). We are calling device_put() on the
error path, but are missing it from the device remove path. This causes
release() to never get called for the devices on remove.
Let's add the missing put_device() calls for both serial ctrl and
port devices.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Reported-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20230804090909.51529-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpm_uart_map_pram() and cpm_uart_unmap_pram() are very
similar for CPM1 and CPM2.
On CPM1 cpm_uart_map_pram() uses of_iomap() while CPM2 uses
of_address_to_resource()/ioremap(). CPM2 version will also
work on CPM1.
On CPM2 cpm_uart_map_pram() and cpm_uart_unmap_pram() has a special
handling for SMC. Just gate it by an IS_ENABLED(CONFIG_CPM2).
So move the CPM2 version into cpm_uart_core.c which is the only
user of those two fonctions and refactor to also handle CPM1 as
mentionned above.
PROFF_SMC_SIZE is only defined for SMC2 and used only there. To make
it simple, just use the numerical value 64, this is the only place
it is used and anyway there's already the same numerical value for
the alignment.
Use cpm_muram_alloc() instead of cpm_dpalloc() macro.
Then cpm_uart_cpm1.c and cpm_uart_cpm2.c are now empty and go away.
Replace printk(KERN_WARN by pr_warn( to make checkpatch happier.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/44a266106c421319aa8e700c2db52d5dcd652c0f.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpm_uart_freebuf() is identical for CPM1 and CPM2.
cpm_uart_allocbuf() only has a small difference between CPM1 and CPM2
as shown below:
CPM1:
if (is_con) {
/* was hostalloc but changed cause it blows away the */
/* large tlb mapping when pinning the kernel area */
mem_addr = (u8 *) cpm_dpram_addr(cpm_dpalloc(memsz, 8));
dma_addr = (u32)cpm_dpram_phys(mem_addr);
} else
mem_addr = dma_alloc_coherent(pinfo->port.dev, memsz, &dma_addr,
GFP_KERNEL);
CPM2:
if (is_con) {
mem_addr = kzalloc(memsz, GFP_NOWAIT);
dma_addr = virt_to_bus(mem_addr);
}
else
mem_addr = dma_alloc_coherent(pinfo->port.dev, memsz, &dma_addr,
GFP_KERNEL);
Refactor this by using IS_ENABLED(CONFIG_CPM1)
and move both functions in cpm_uart_core.c as they are used only there.
While doing this, add the necessary casts to silence sparse for the CPM1
part. This is because a dma alloc is not expected to be an iomem but
for CPM1 as we use DPRAM this is seen as iomem.
Also replace calls to cpm_dpxxxx() by relevant cpm_muram_xxxx() calls.
This is needed at least for cpm_dpram_phys() which is only defined
for CPM1. Just do the same for all so that cpm_dpxxxx() macros can get
droped in the future.
To silence checkpatch, replace printk(KERN_ERR by pr_err( and display
function name instead of hard coded filename. Also replace
mem_addr == NULL by !mem_addr.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/606dfdd258a4f2f2882e2e189bef37526bb3b499.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CPMFCR_EB is the same as SMC_EB and is defined
for both CPM1 and CPM2.
CPMFCR_GBL is defined as 0 for CPM1.
Therefore the CPM2 version of cpm_set_scc_fcr() and
cpm_set_smc_fcr() can be used on both CPM1 and CPM2.
And cpm_set_brg() is already identical and just a
wrapper of cpm_setbrg().
In addition those three fonctions are only called once
from cpm_uart_core.c, so just replace the calls with
the content of the CPM2 versions of them.
And DPRAM_BASE is identical so can go in cpm_uart.h. While
moving it, use cpm_muram_addr() directly instead of the
cpm_dpram_addr() macro and remove __force tag which isn't needed.
Then cpm_uart_cpm1.h and cpm_uart_cpm2.h go away.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/6920e61fd362961ae1aeda897c8bfe1efacdc9dc.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_baudrate() is just a trivial wrapper to get_baudrate().
Use get_baudrate() directly and remove assignment in if condition.
And also remove uart_clock() which is not used since
commit 0b2a2e5b77 ("cpm_uart: Remove !CONFIG_PPC_CPM_NEW_BINDING
code")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/4d497386f576a3df768e44a04f9bb512e424c311.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpm_uart_init_portdesc()
smc1_lineif()
smc2_lineif()
scc1_lineif()
scc2_lineif()
scc3_lineif()
scc4_lineif()
Those functions were removed by commit 0b2a2e5b77 ("cpm_uart: Remove
!CONFIG_PPC_CPM_NEW_BINDING code"). Remove stale prototypes.
UART_SMC{1..2} and UART_SCC{1..4} and SCC_WAIT_CLOSING macros are not
used anymore since the above commit.
cpm_uart_ports[] isn't used outside cpm_uart_core.c since the
same commit, so make it static.
cpm_uart_init_smc() and cpm_uart_init_scc() don't need a forward
declaration.
FLAG_DISCARDING and IS_DISCARDING have never been used since at
least 2.6.12 and the start of git repository for kernel.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/96ef20ae1df056d1b7967871ba6e27e5b5aaeea6.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module_mcb_driver() will set "THIS_MODULE" to driver.owner when
register a mcb_driver driver, so it is redundant initialization to set
driver.owner in mcb_driver statement. Remove it for clean code.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230804100843.100348-1-lizetao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a warning reported by coccinelle:
./drivers/tty/serial/8250/8250_men_mcb.c:226:6-19: WARNING:
Unsigned expression compared with zero: data -> line [ i ] < 0
The array "line" of serial_8250_men_mcb_data is used to record the
registered serial port. When register a port failed, it will return
an error code, but the type of "line" is "unsigned int", causing
the error code to reverse. Modify the type of "data -> line" to solve
this problem.
Fixes: 2554e6ba28 ("8250_men_mcb: Read num ports from register data.")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230803142053.1308926-1-lizetao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The data->line[i] is defined as unsigned int type, if(data->line[i] < 0)
is invalid, so replace data->line[i] with res.
./drivers/tty/serial/8250/8250_men_mcb.c:223:6-19: WARNING: Unsigned expression compared with zero: data->line[i] < 0.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=6088
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230803084753.51253-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least freeze, restore and thaw need to be set in order for the driver
to support system hibernation. The existing suspend/resume functions can
be reused since those functions don't touch the device's power state or
wakeup capability. Use the helper macros SET_SYSTEM_SLEEP_PM_OPS and
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for symmetry with similar drivers.
Signed-off-by: Anton Eliasson <anton.eliasson@axis.com>
Link: https://lore.kernel.org/r/20230803-samsung_tty_pm_ops-v1-1-1ea7be72194d@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit a85a6c86c2 ("driver core: platform: Clarify that
IRQ 0 is invalid"), there is no possible for
platform_get_irq() to return 0. Use the return value
from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230803091712.596987-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a warning reported by coccinelle:
./drivers/tty/serial/ma35d1_serial.c:791:3-8:
No need to set .owner here. The core will do it.
The module_platform_driver() will set "THIS_MODULE" to driver.owner
when register a driver for platform-level devices, so it is redundant
initialization to set driver.owner in ma35d1serial_driver statement.
Remove it to silence the warning.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230803032353.3045221-1-lizetao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While fixing DEVNAME to be more usable, I broke serial_base_match() as the
ctrl and port prefix for device names seemed unnecessary.
The prefixes are still needed by serial_base_match() to probe the serial
base controller port, and serial tx is now broken.
Let's fix the issue by checking against dev->type and drv->name instead
of the prefixes that are no longer in the DEVNAME.
Fixes: 1ef2c2df11 ("serial: core: Fix serial core controller port name to show controller id")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202308021529.35b3ad6c-oliver.sang@intel.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230803071034.25571-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are missing the serial core controller id for the serial core port
name. Let's fix the issue for sane sysfs output, and to avoid issues
addressing serial ports later on.
And as we're now showing the controller id, the "ctrl" and "port" prefix
for the DEVNAME become useless, we can just drop them. Let's standardize on
DEVNAME:0 for controller name, where 0 is the controller id. And
DEVNAME:0.0 for port name, where 0.0 are the controller id and port id.
This makes the sysfs output nicer, on qemu for example:
$ ls /sys/bus/serial-base/devices
00:04:0 serial8250:0 serial8250:0.2
00:04:0.0 serial8250:0.1 serial8250:0.3
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230725054216.45696-4-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core port id should be serial core controller specific port
instance, which is not always the port->line index.
For example, 8250 driver maps a number of legacy ports, and when a
hardware specific device driver takes over, we typically have one
driver instance for each port. Let's instead add port->port_id to
keep track serial ports mapped to each serial core controller instance.
Currently this is only a cosmetic issue for the serial core port device
names. The issue can be noticed looking at /sys/bus/serial-base/devices
for example though. Let's fix the issue to avoid port addressing issues
later on.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230725054216.45696-3-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not read the data register to clear the error flags for lpuart32
platforms, the additional read may cause the receive FIFO underflow
since the DMA has already read the data register.
Actually all lpuart32 platforms support write 1 to clear those error
bits, let's use this method to better clear the error flags.
Fixes: 42b68768e5 ("serial: fsl_lpuart: DMA support for 32-bit variant")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230801022304.24251-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'status' is assigned a result from readl(). There is no need for the
variable to be 'unsigned long'. readl() returns 32bit values.
Provided, this is a Nios II driver (32-bit), there is no change in
semantics. This only makes the type explicit.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20230731080244.2698-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart code currently does the following in uart_write() and
uart_flush_buffer():
if (cond) {
WARN_ON(1);
return;
}
It can be rewritten to more obvious and more readable:
if (WARN_ON(cond))
return;
Do so.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230731080244.2698-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small TTY and serial driver fixes for 6.5-rc4 for some
reported problems. Included in here is:
- TIOCSTI fix for braille readers
- documentation fix for minor numbers
- MAINTAINERS update for new serial files in -rc1
- minor serial driver fixes for reported problems
All of these have been in linux-next with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZMZCMQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym8fQCdGtm3DH+/BVKEebLUBlTb2Gz3xrIAnjeDVdP3
8Yztt4MNSYi7gvOMHQi5
=e8rX
-----END PGP SIGNATURE-----
Merge tag 'tty-6.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small TTY and serial driver fixes for 6.5-rc4 for some
reported problems. Included in here is:
- TIOCSTI fix for braille readers
- documentation fix for minor numbers
- MAINTAINERS update for new serial files in -rc1
- minor serial driver fixes for reported problems
All of these have been in linux-next with no reported problems"
* tag 'tty-6.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_dw: Preserve original value of DLF register
tty: serial: sh-sci: Fix sleeping in atomic context
serial: sifive: Fix sifive_serial_console_setup() section
Documentation: devices.txt: reconcile serial/ucc_uart minor numers
MAINTAINERS: Update TTY layer for lists and recently added files
tty: n_gsm: fix UAF in gsm_cleanup_mux
TIOCSTI: always enable for CAP_SYS_ADMIN
Each of the 4 PCI functions on ASIX AX99100 PCIe to Multi I/O
Controller can be configured as a single-port serial port controller.
The subvendor id is 0x1000 when configured as serial port and MSI
interrupts are supported.
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230724083933.3173513-4-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The global pointer 'sprd_port' may not zero when sprd_probe returns
failure, that is a risk for sprd_port to be accessed afterward, and
may lead to unexpected errors.
For example:
There are two UART ports, UART1 is used for console and configured in
kernel command line, i.e. "console=";
The UART1 probe failed and the memory allocated to sprd_port[1] was
released, but sprd_port[1] was not set to NULL;
In UART2 probe, the same virtual address was allocated to sprd_port[2],
and UART2 probe process finally will go into sprd_console_setup() to
register UART1 as console since it is configured as preferred console
(filled to console_cmdline[]), but the console parameters (sprd_port[1])
belong to UART2.
So move the sprd_port[] assignment to where the port already initialized
can avoid the above issue.
Fixes: b7396a38fb ("tty/serial: Add Spreadtrum sc9836-uart driver support")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20230725064053.235448-1-chunyan.zhang@unisoc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the IOControl register bits description in the page 31 of
the product datasheet, we know the bit 3 of IOControl register is
softreset, this bit will self-clearing once the reset finish.
In the probe, the softreset bit is set, and when we read this register
from debugfs/regmap interface, we found the softreset bit is still
setting, this confused us for a while. Finally we found this register
is cached, to read the real value from register, we could put it
into the regmap_volatile().
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20230724034727.17335-1-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
in asc_init_port, clk_prepare_enable may fail, therefore, the
return value of clk_prepare_enable should be checked.
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Link: https://lore.kernel.org/r/20230717144733.24194-1-ruc_gongyuanjun@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Macroses for name generation are not useful. They hide the real place
for object declaration. Instead, use direct names such as
'meson_uart_driver_*' and 'meson_serial_console_*' for all objects.
Additionally, rename 'MESON_SERIAL_CONSOLE_DEFINE()' to
'MESON_SERIAL_CONSOLE()', and 'MESON_UART_DRIVER_DEFINE()' to
'MESON_UART_DRIVER()' to simplify the code.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230728071522.17503-1-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ioremap() fails, it returns NULL pointer, not ERR_PTR(), fix the
return value check and call release_mem_region() to release resource.
Fixes: c563831ba8 ("8250_men_mcb: Make UART config auto configurable")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20230728085723.3195044-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preserve the original value of the Divisor Latch Fraction (DLF) register.
When the DLF register is modified without preservation, it can disrupt
the baudrate settings established by firmware or bootloader, leading to
data corruption and the generation of unreadable or distorted characters.
Fixes: 701c5e73b2 ("serial: 8250_dw: add fractional divisor support")
Cc: stable <stable@kernel.org>
Signed-off-by: Ruihong Luo <colorsu1922@gmail.com>
Link: https://lore.kernel.org/stable/20230713004235.35904-1-colorsu1922%40gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230713004235.35904-1-colorsu1922@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is called indirectly from the platform driver probe
function. Even if the driver is built in, it may be probed after
free_initmem() due to deferral or unbinding/binding via sysfs.
Thus the function cannot be marked as __init.
Fixes: 45c054d081 ("tty: serial: add driver for the SiFive UART")
Cc: stable <stable@kernel.org>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20230624060159.3401369-1-samuel.holland@sifive.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-15-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-14-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-13-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-12-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-11-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-10-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20230712062853.11007-9-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-8-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-7-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-6-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-5-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-4-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-3-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-2-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-1-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the clock-rate debug printk more readable by using an equal sign
instead of a dash as separator between names and values and adding some
spaces:
qcom_geni_serial 988000.serial: desired_rate = 1843200, clk_rate = 7372800, clk_div = 4
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230714130214.14552-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The operating-performance-point vote needs to be dropped when shutting
down the port to avoid wasting power by keeping resources like power
domains in an unnecessarily high performance state (e.g. when a UART
connected Bluetooth controller is not in use).
Fixes: a5819b548a ("tty: serial: qcom_geni_serial: Use OPP API to set clk/perf state")
Cc: stable@vger.kernel.org # 5.9
Cc: Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230714130214.14552-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add IDLE interrupt support for receive dma on imx7ulp/imx8ulp/imx8qxp
platforms to replace the receive dma timer function, because the receive
dma timer has bigger latency than idle interrupt triggering, which may
cause the Bluetooth Firmware download timeout on Android platform(it
has a limited FW download time window).
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230710013857.7396-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the lpuart32_int() below lpuart_copy_rx_to_tty(), this is a
preparation patch for the next patch to avoid the function declaration,
no actual functional changes.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230710013857.7396-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mrvl,pxa-uart already supports earlycon and both compatible strings use
the same driver, so there's no reason for mmp-uart to not have earlycon
as well.
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20230721210042.21535-2-duje.mihanovic@skole.hr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement separate uart_data to ensure proper devname value for the A1
SoC family. Use 'ttyS' devname, as required by the A1 architecture,
instead of the legacy gx architecture.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230705181833.16137-6-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to use the correct devname value for the S4 SoC family, it
is imperative that we implement separate uart_data. Unlike the legacy
g12a architecture, the S4 architecture should employ the use of 'ttyS'
devname.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230705181833.16137-5-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is worth noting that the devname ttyS is a widely recognized tty name
and is commonly used by many uart device drivers. Given the established
usage and compatibility concerns, it may not be feasible to change the
devname for older SoCs. However, for new definitions, it is acceptable
and even recommended to use a new devname to help ensure clarity and
avoid any potential conflicts on lower or upper software levels.
For more information please refer to IRC discussion at [1].
Links:
[1]: https://libera.irclog.whitequark.org/linux-amlogic/2023-07-03
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Link: https://lore.kernel.org/r/20230705181833.16137-4-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Actually, the meson_uart module is already a platform_driver, but it is
currently registered manually and the uart core registration is run
outside the probe() scope, which results in some restrictions. For
instance, it is not possible to communicate with the OF subsystem
because it requires an initialized device object.
To address this issue, apply module_platform_driver() instead of direct
module init/exit routines. Additionally, move uart_register_driver() to
the driver probe(), and destroy manual console registration because it's
already run in the uart_register_driver() flow.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230705181833.16137-3-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_probe() helper for error checking and standard logging.
It makes the driver's probe() function a little bit shorter.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230705181833.16137-2-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART ports created by this driver were not usable out of
the box, so let the configuration be handled by the 8250 UART
subsystem. This makes the implementation simpler and the UART
port more usable.
The 8250 UART subsystem will take care of requesting the memory
resources, but the driver needs to first read the register where
the num ports is set, so a request of the resource is needed
before registering the UART port.
Co-developed-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Javier Rodriguez <josejavier.rodriguez@duagon.com>
Link: https://lore.kernel.org/r/20230705131423.30552-4-josejavier.rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IP Core Z025 and Z057 have a register where the amount of UART
ports is specified. Such register is located at offset 0x40.
This patch fixes the way the UART ports is calculated by reading
the actual register. Additionally a refactor was needed to achieve
this so we can keep track of the UART line and its offset which
also improves the remove callback.
Co-developed-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Javier Rodriguez <josejavier.rodriguez@duagon.com>
Link: https://lore.kernel.org/r/20230705131423.30552-3-josejavier.rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some F215 FPGA multifunction boards announce themselves as 215.
This leads to a misconfigured clockrate. The F215 is the same board
as G215 but with different cPCI interface so make them get the same
configuration
Co-developed-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Javier Rodriguez <josejavier.rodriguez@duagon.com>
Link: https://lore.kernel.org/r/20230705131423.30552-2-josejavier.rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the Tegra serial driver is probe before clocks are available then the
following error is seen on boot:
serial-tegra 3100000.serial: Couldn't get the clock
This has been observed on Jetson AGX Orin. Fix this by calling
dev_err_probe() instead of dev_err() to avoid printing an error on probe
deferral.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20230703113759.75608-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # for imx
Link: https://lore.kernel.org/r/20230724205440.767071-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the Qualcomm interconnect defines rather than magic numbers for the
icc tags also in the restore() PM callback.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230711160516.30502-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reconcile devices.txt with serial/ucc_uart.c regarding device number
assignments. ucc_uart.c supports 4 ports and uses minor devnums
46-49, so update devices.txt with that info.
Then update ucc_uart.c's reference to the location of the devices.txt
list in the kernel source tree.
Fixes: d7584ed2b9 ("[POWERPC] qe-uart: add support for Freescale QUICCEngine UART")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Timur Tabi <timur@kernel.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-serial@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Link: https://lore.kernel.org/r/20230724063341.28198-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The local 'flag' variable carries only TTY_NORMAL. So use that constant
directly and drop the variable.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230712081811.29004-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* move the declaration of flg (with the initializer) to the loop, so
there is no need to reset it to TTY_NORMAL by an 'else' branch.
* use TTY_NORMAL as initializer above, not a magic zero constant
* remove the outer 'if' from this construct:
if (S & (A | B)) {
if (S & A)
X;
if (S & B)
Y;
}
* drop unlikely() as I doubt it has any benefits here. If it does,
provide numbers.
All four make the code easier to read.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Vineet Gupta <vgupta@kernel.org>
Acked-by: Vineet Gupta <vgupta@kernel.org>
Link: https://lore.kernel.org/r/20230712081811.29004-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__uart_start() does not need a tty struct. It works only with
uart_state. So pass the latter directly.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230712081811.29004-8-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both the character and flag are 8-bit values. So switch from unsigned
ints to u8s. The drivers will be cleaned up in the next round.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230712081811.29004-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Propagate u8 from the sysrq code further up to serial's
uart_handle_sysrq_char() and friends.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230712081811.29004-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The runtime PM state should not be changed by drivers that do not
implement runtime PM even if it happens to work around a bug in PM core.
With the wake irq arming now fixed, drop the bogus runtime PM state
update which left the device in active state (and could potentially
prevent a parent device from suspending).
Fixes: f3974413cf ("tty: serial: qcom_geni_serial: Wakeup IRQ cleanup")
Cc: 5.6+ <stable@vger.kernel.org> # 5.6+
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is the big set of tty/serial driver updates for 6.5-rc1.
Included in here are:
- tty_audit code cleanups from Jiri
- more 8250 cleanups from Ilpo
- samsung_tty driver bugfixes
- 8250 lock port updates
- usual fsl_lpuart driver updates and fixes
- other small serial driver fixes and updates, full details in the
shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZKKVTQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl+wACgwWX8fdrkBHASPVkcYOn8xa27E08AnjNz2Y8K
vvOII6EEYKwFjEkjAoIX
=By18
-----END PGP SIGNATURE-----
Merge tag 'tty-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty/serial driver updates for 6.5-rc1.
Included in here are:
- tty_audit code cleanups from Jiri
- more 8250 cleanups from Ilpo
- samsung_tty driver bugfixes
- 8250 lock port updates
- usual fsl_lpuart driver updates and fixes
- other small serial driver fixes and updates, full details in the
shortlog
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
tty_audit: make data of tty_audit_log() const
tty_audit: make tty pointers in exposed functions const
tty_audit: make icanon a bool
tty_audit: invert the condition in tty_audit_log()
tty_audit: use kzalloc() in tty_audit_buf_alloc()
tty_audit: use TASK_COMM_LEN for task comm
Revert "8250: add support for ASIX devices with a FIFO bug"
serial: atmel: don't enable IRQs prematurely
tty: serial: Add Nuvoton ma35d1 serial driver support
tty: serial: fsl_lpuart: add earlycon for imx8ulp platform
tty: serial: imx: fix rs485 rx after tx
selftests: tty: add selftest for tty timestamp updates
tty: tty_io: update timestamps on all device nodes
tty: fix hang on tty device with no_room set
serial: core: fix -EPROBE_DEFER handling in init
serial: 8250_omap: Use force_suspend and resume for system suspend
tty: serial: samsung_tty: Use abs() to simplify some code
tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() when iterating clk
tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() in case of error
serial: 8250: Apply FSL workarounds also without SERIAL_8250_CONSOLE
...
Here are a small set of changes for 6.5-rc1 for some driver core
changes. Included in here are:
- device property cleanups to make it easier to write "agnostic"
drivers when regards to the firmware layer underneath them (DT vs.
ACPI)
- debugfs documentation updates
- devres additions
- sysfs documentation and changes to handle empty directory creation
logic better
- tiny kernfs optimizations
- other tiny changes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZKKSEQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoowCfT+Joha+cz4edAFUvd55lKPPJJFsAoNiprHmX
di37sirvn6vo54Hk0Nyq
=qqTo
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are a small set of changes for 6.5-rc1 for some driver core
changes. Included in here are:
- device property cleanups to make it easier to write "agnostic"
drivers when regards to the firmware layer underneath them (DT vs.
ACPI)
- debugfs documentation updates
- devres additions
- sysfs documentation and changes to handle empty directory creation
logic better
- tiny kernfs optimizations
- other tiny changes
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: Skip empty folders creation
sysfs: Improve readability by following the kernel coding style
drivers: fwnode: fix fwnode_irq_get[_byname]()
ata: ahci_platform: Make code agnostic to OF/ACPI
device property: Implement device_is_compatible()
ACPI: Move ACPI_DEVICE_CLASS() to mod_devicetable.h
base/node: Use 'property' to identify an access parameter
driver core: device.h: add some missing kerneldocs
kernfs: fix missing kernfs_idr_lock to remove an ID from the IDR
isa: Remove unnecessary checks
MAINTAINERS: add entry for auxiliary bus
debugfs: Correct the 'debugfs_create_str' docs
serial: qcom_geni: Comment use of devm_krealloc rather than devm_krealloc_array
iio: adc: Use devm_krealloc_array
hwmon: pmbus: Use devm_krealloc_array
brings some order to the documentation directory, declutters the top-level
directory, and makes the documentation organization more closely match that
of the source.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAmSbDRwPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Y0b0H/A69Yxns1Bf465rNNINREaWWzJzIPGyJax9F
7x2zYphL2BLmDysHDvBpP858ytA4qzmqS7TopI1zjqTS6Uh4qTfsQTWNfk536Oyi
XOkKONPAqzuk4Pvsam4t46lMb5xqkyy7FcsZSp25ona7t8nLiTkoxTWIabvFziFN
F7qJ/u/Uzck53FgR2Xtss4vrkcWDTgva5SzQUhoxGfEqjEOoQi7CfqLQC468wfOt
/XlBCnTRPnZ6bFiD/9QHU+D0setWVBs0IJHH2ogDlx/FHOvp83haJHVRFNYpx0Gd
UY72gEbovzYauKMaa6azBo+1Tje6tTu6wfV3ZAG8UJYe/vJkdUw=
=EBMZ
-----END PGP SIGNATURE-----
Merge tag 'docs-arm-move' of git://git.lwn.net/linux
Pull arm documentation move from Jonathan Corbet:
"Move the Arm architecture documentation under Documentation/arch/.
This brings some order to the documentation directory, declutters the
top-level directory, and makes the documentation organization more
closely match that of the source"
* tag 'docs-arm-move' of git://git.lwn.net/linux:
dt-bindings: Update Documentation/arm references
docs: update some straggling Documentation/arm references
crypto: update some Arm documentation references
mips: update a reference to a moved Arm Document
arm64: Update Documentation/arm references
arm: update in-source documentation references
arm: docs: Move Arm documentation to Documentation/arch/
This reverts commit eb26dfe8aa.
Commit eb26dfe8aa ("8250: add support for ASIX devices with a FIFO
bug") merged on Jul 13, 2012 adds a quirk for PCI_VENDOR_ID_ASIX
(0x9710). But that ID is the same as PCI_VENDOR_ID_NETMOS defined in
1f8b061050c7 ("[PATCH] Netmos parallel/serial/combo support") merged
on Mar 28, 2005. In pci_serial_quirks array, the NetMos entry always
takes precedence over the ASIX entry even since it was initially
merged, code in that commit is always unreachable.
In my tests, adding the FIFO workaround to pci_netmos_init() makes no
difference, and the vendor driver also does not have such workaround.
Given that the code was never used for over a decade, it's safe to
revert it.
Also, the real PCI_VENDOR_ID_ASIX should be 0x125b, which is used on
their newer AX99100 PCIe serial controllers released on 2016. The FIFO
workaround should not be intended for these newer controllers, and it
was never implemented in vendor driver.
Fixes: eb26dfe8aa ("8250: add support for ASIX devices with a FIFO bug")
Cc: stable <stable@kernel.org>
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230619155743.827859-1-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The atmel_complete_tx_dma() function disables IRQs at the start
of the function by calling spin_lock_irqsave(&port->lock, flags);
There is no need to disable them a second time using the
spin_lock_irq() function and, in fact, doing so is a bug because
it will enable IRQs prematurely when we call spin_unlock_irq().
Just use spin_lock/unlock() instead without disabling or enabling
IRQs.
Fixes: 08f738be88 ("serial: at91: add tx dma support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/cb7c39a9-c004-4673-92e1-be4e34b85368@moroto.mountain
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds UART and console driver for Nuvoton ma35d1 Soc.
It supports full-duplex communication, FIFO control, and
hardware flow control.
Command line set "console=ttyNVT0,115200", NVT means
Nuvoton MA35 UART port. The UART driver probe will
create path named "/dev/ttyNVTx".
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230619032330.233796-2-ychuang570808@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal
active high") RS485 reception no longer works after a transmission.
The following scenario shows the problem:
1) Open a port in RS485 mode
2) Receive data from remote (OK)
3) Transmit data to remote (OK)
4) Receive data from remote (Nothing received)
In RS485 mode, imx_uart_start_tx() calls imx_uart_stop_rx() and, when the
transmission is complete, imx_uart_stop_tx() calls imx_uart_start_rx().
Since the above commit imx_uart_stop_rx() now sets the loopback bit but
imx_uart_start_rx() does not clear it causing the hardware to remain in
loopback mode and not receive external data.
Fix this by moving the existing loopback disable code to a helper function
and calling it from imx_uart_start_rx() too.
Fixes: 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230616104838.2729694-1-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Arm documentation has moved to Documentation/arch/arm; update the
last remaining references to match.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # for pwm
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The -EPROBE_DEFER error path in serial_base_device_init() is a bit
awkward. Before the call to device_initialize(dev) then we need to
manually release all the device resources. And after the call then we
need to call put_device() to release the resources. Doing either one
wrong will result in a leak or a use after free.
So let's wait to return -EPROBE_DEFER until after the call to
device_initialize(dev) so that way callers do not have to handle
-EPROBE_DEFER as a special case. Now callers can just use put_device()
for clean up.
The second issue with the -EPROBE_DEFER path is that deferring is not
supposed to be a fatal error, but instead it's normal part of the
init process and the kernel recovers from it automatically. That means
we should not print an error message but just a debug message on this
path.
Fixes: 539914240a ("serial: core: Fix probing serial_base_bus devices")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Message-ID: <18318adb-ab2c-4dcc-9f96-498a13d16b80@moroto.mountain>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not rely on autosuspend timeout for system suspend. Instead,
let's use force_suspend and force_resume functions. Otherwise the serial
port controller device may not be idled on suspend.
As we are doing a register write on suspend to configure the serial port,
we still need to runtime PM resume the port on suspend.
While at it, let's switch to pm_runtime_resume_and_get() and check for
errors returned. And let's add the missing line break before return to the
suspend function while at it.
Fixes: 09d8b2bdbc ("serial: 8250: omap: Provide ability to enable/disable UART as wakeup source")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Message-ID: <20230614045922.4798-1-tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the best clk is searched, we iterate over all possible clk.
If we find a better match, the previous one, if any, needs to be freed.
If a better match has already been found, we still need to free the new
one, otherwise it leaks.
Cc: <stable@vger.kernel.org> # v3.3+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Fixes: 5f5a7a5578 ("serial: samsung: switch to clkdev based clock lookup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Message-ID: <cf3e0053d2fc7391b2d906a86cd01a5ef15fb9dc.1686412569.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If clk_get_rate() fails, the clk that has just been allocated needs to be
freed.
Cc: <stable@vger.kernel.org> # v3.3+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Fixes: 5f5a7a5578 ("serial: samsung: switch to clkdev based clock lookup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Message-ID: <e4baf6039368f52e5a5453982ddcb9a330fc689e.1686412569.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LS1028A is using DMA with LPUART. Having RX watermark set to 1, means
DMA transactions are started only after receiving the second character.
On other platforms with newer LPUART IP, Receiver Idle Empty function
initiates the DMA request after the receiver is idling for 4 characters.
But this feature is missing on LS1028A, which is causing a 1-character
delay in the RX direction on this platform.
Set RX watermark to 0 to initiate RX DMA after each character.
Link: https://lore.kernel.org/linux-serial/20230607103459.1222426-1-robert.hodaszi@digi.com/
Fixes: 9ad9df8447 ("tty: serial: fsl_lpuart: Fix the wrong RXWATER setting for rx dma case")
Cc: stable <stable@kernel.org>
Signed-off-by: Robert Hodaszi <robert.hodaszi@digi.com>
Message-ID: <20230609121334.1878626-1-robert.hodaszi@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The need to handle the FSL variant of 8250 in a special way is also
present without console support. So soften the dependency for
SERIAL_8250_FSL from SERIAL_8250_CONSOLE to SERIAL_8250. To handle
SERIAL_8250=m, the FSL code can be modular, too, thus SERIAL_8250_FSL
becomes tristate.
Compiling 8250_fsl as a module requires adding a module license so this
is added, too. While add it also add a appropriate module description.
As then SERIAL_OF_PLATFORM=y + SERIAL_8250_FSL=m is a valid combination
(if COMPILE_TEST is enabled on a platform that is neither PPC, ARM nor
ARM64), the check in 8250_of.c must be weakened a bit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Message-ID: <20230609133932.786117-3-u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The put_device() function will call serial_base_ctrl_release() or
serial_base_port_release() so these kfrees() are a double free bug.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Message-ID: <ZH7tsTmWY5b/4m+6@moroto>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the error interrupt is never acknowledged, so once active it
will stay active indefinitely, causing the handler to be called in an
infinite loop.
Fixes: 2f0fc4159a ("SERIAL: Lantiq: Add driver for MIPS Lantiq SOCs.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Bernhard Seibold <mail@bernhard-seibold.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Message-ID: <20230602133029.546-1-mail@bernhard-seibold.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_mtk driver's runtime PM support has some issues:
- The bus clock is enabled (through runtime PM callback) later than a
register write
- runtime PM resume callback directly called in probe, but no
pm_runtime_set_active() call is present
- UART PM function calls the callbacks directly, _and_ calls runtime
PM API
- runtime PM callbacks try to do reference counting, adding yet another
count between runtime PM and clocks
This fragile setup worked in a way, but broke recently with runtime PM
support added to the serial core. The system would hang when the UART
console was probed and brought up.
Tony provided some potential fixes [1][2], though they were still a bit
complicated. The 8250_dw driver, which the 8250_mtk driver might have
been based on, has a similar structure but simpler runtime PM usage.
Simplify clock sequencing and runtime PM support in the 8250_mtk driver.
Specifically, the clock is acquired enabled and assumed to be active,
unless toggled through runtime PM suspend/resume. Reference counting is
removed and left to the runtime PM core. The serial pm function now
only calls the runtime PM API.
[1] https://lore.kernel.org/linux-serial/20230602092701.GP14287@atomide.com/
[2] https://lore.kernel.org/linux-serial/20230605061511.GW14287@atomide.com/
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Message-ID: <20230606091747.2031168-1-wenst@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes the property name read in the driver according to the YAML.
According to device-tree documentation, property names should not
include underscores.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Message-ID: <20230604083558.16661-1-rgallaispou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checking for NULL is incorrect as serial_base_ctrl_add() uses ERR_PTR().
Let's also pass any returned error along, there's no reason to translate
all errors to -ENODEV.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230602070007.59268-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a physical serial port device driver uses arch_initcall() we fail to
probe the serial_base_bus devices and the serial port tx fails. This is
because as serial_base_bus uses module_initcall().
Let's fix the issue by changing serial_base_bus to use arch_initcall().
Let's also return an error if a driver attempts to call uart_add_one_port()
too early.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/linux-serial/20230601132012.GB14287@atomide.com/T/#m6a40440fc04d551d27b147da8602e065c982a115
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230601141445.11321-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 84a9582fd2 ("serial: core: Start managing serial controllers to
enable runtime PM") required the caller to hold port_mutex rather than
taking it locally. However the mutex_unlock() call wasn't removed
causing the mutex to be dropped unexpectly. Remove the call to
mutex_unlock() (and fix up the early return) to restore correct
behaviour.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Steven Price <steven.price@arm.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230601105548.29965-1-steven.price@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to enable runtime PM for serial port device drivers in a generic
way. To do this, we want to have the serial core layer manage the
registered physical serial controller devices.
To manage serial controllers, let's set up a struct bus and struct device
for the serial core controller as suggested by Greg and Jiri. The serial
core controller devices are children of the physical serial port device.
The serial core controller device is needed to support multiple different
kind of ports connected to single physical serial port device.
Let's also set up a struct device for the serial core port. The serial
core port instances are children of the serial core controller device.
With the serial core port device we can now flush pending TX on the
runtime PM resume as suggested by Johan.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230525113034.46880-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new uart_write() function is only called from suspend/resume code, causing
a build warning when those are left out:
drivers/tty/serial/8250/8250_omap.c:169:13: error: 'uart_write' defined but not used [-Werror=unused-function]
Remove the #ifdefs and use the modern pm_ops/pm_sleep_ops and their wrappers
to let the compiler see where it's used but still drop the dead code.
Fixes: 398cecc248 ("serial: 8250: omap: Fix imprecise external abort for omap_8250_pm()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230517202012.634386-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After working quite a bit on erratic behaviour of the MPC83xx UART I
(think I) understood the problem. Expand the description accoringly to
conserve the knowledge for the future.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230524122754.481816-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a COMPILE_TEST configuration, the cpm_uart driver uses symbols from
the cpm_uart_cpm2.c file. This file is compiled only when CONFIG_CPM2 is
set.
Without this dependency, the linker fails with some missing symbols for
COMPILE_TEST configuration that needs SERIAL_CPM without enabling CPM2.
This lead to:
depends on CPM2 || CPM1 || (PPC32 && CPM2 && COMPILE_TEST)
This dependency does not make sense anymore and can be simplified
removing all the COMPILE_TEST part.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305160221.9XgweObz-lkp@intel.com/
Fixes: e3e7b13bff ("serial: allow COMPILE_TEST for some drivers")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230523085902.75837-3-herve.codina@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPUART IP now has two known bugs, one is that CTS has higher priority
than the break signal, which causes the break signal sending through
UARTCTRL_SBK may impacted by the CTS input if the HW flow control is
enabled. It exists on all platforms we support in this driver.
So we add a workaround patch for this issue: commit c4c81db5cf
("tty: serial: fsl_lpuart: disable the CTS when send break signal").
Another IP bug is i.MX8QM LPUART may have an additional break character
being sent after SBK was cleared. It may need to add some delay between
clearing SBK and re-enabling CTS to ensure that the SBK latch are
completely cleared.
But we found that during the delay period before CTS is enabled, there
is still a risk that Bluetooth data in TX FIFO may be sent out during
this period because of break off and CTS disabled(even if BT sets CTS
line deasserted, data is still sent to BT).
Due to this risk, we have to drop the CTS-disabling workaround for SBK
bugs, use TXINV seems to be a better way to replace SBK feature and
avoid above risk. Also need to disable the transmitter to prevent any
data from being sent out during break, then invert the TX line to send
break. Then disable the TXINV when turn off break and re-enable
transmitter.
Fixes: c4c81db5cf ("tty: serial: fsl_lpuart: disable the CTS when send break signal")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230519094751.28948-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current config comment for SERIAL_8250_FINTEK implies that this
option is only needed when one wants to support RS485. As it turns
out we also need to enable this option for RS232 support to function
correctly on some variants.
For example for variants such as the F71869AD attempting to use
multiple RS232 ports simultaneously without this option enabled can
result in data corruption.
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Link: https://lore.kernel.org/r/20230521075046.3539376-1-james.hilliard1@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coverity reports the Unchecked return value (CHECKED_RETURN) warning:
Calling dmaengine_tx_status without checking return value.
So here add the return value check for dmaengine_tx_status() function to
make coverity happy.
Fixes: cf9aa72d2f ("tty: serial: fsl_lpuart: optimize the timer based EOP logic")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230522025111.3747-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230525210147.734737-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART_IER register is modified twice by each console write
(serial8250_console_write()) under the port lock. Any driver code that
accesses UART_IER must do so with the port locked in order to ensure
consistent values, even when for read accesses.
Add locking, lockdep notation, and/or comments everywhere UART_IER is
accessed. The added locking is not fixing a real problem because it
occurs where the console is not active. However, adding the locking
to these non-critical paths greatly simplifies UART_IER access
tracking by establishing a general policy that all UART_IER access
is performed with the port locked.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230525093159.223817-9-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap8250_irq() accesses UART_IER. This register is modified twice
by each console write (serial8250_console_write()) under the port
lock. omap8250_irq() must also take the port lock to guanentee
synchronized access to UART_IER.
Since the port lock is already being taken for the stop_rx() callback
and since it is safe to call cancel_delayed_work() while holding the
port lock, simply extend the port lock region to include UART_IER
access.
Fixes: 1fe0e1fa32 ("serial: 8250_omap: Handle optional overrun-throttle-ms property")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230525093159.223817-8-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap8250_restore_regs() accesses UART_IER. This register is
modified twice by each console write (serial8250_console_write())
under the port lock. However, not all calls to omap8250_restore_regs()
are under the port lock.
Add the missing port locking around omap8250_restore_regs() calls. Add
lockdep notation to the omap8250_restore_regs().
Note that this is not fixing a real problem because the serial devices
are resumed before console printing is enabled.
However, adding this locking allows for clean locking semantics
for omap8250_restore_regs() so that lockdep can be used to identify
possible problems in the future. It also simplifies synchronization
of UART_IER in general by not needing to rely on such implementation
details.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230525093159.223817-7-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rx_dma() callback (omap_8250_rx_dma) accesses UART_IER. This
register is modified twice by each console write
(serial8250_console_write()) under the port lock. However, not
all calls to the rx_dma() callback are under the port lock.
Add the missing port locking around rx_dma() callback calls. Add
lockdep notation to the omap_8250_rx_dma().
Note that this is not fixing a real problem because:
1. Currently DMA is forced off for 8250_omap consoles.
2. The serial devices are resumed before console printing is enabled.
However, adding this locking allows for clean locking semantics
for the rx_dma() callback so that lockdep can be used to identify
possible problems in the future. It also simplifies synchronization
of UART_IER in general by not needing to rely on implementation
details such as 1 and 2.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230525093159.223817-6-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only user of the start_rx() callback (qcom_geni) directly calls
its own stop_rx() callback. Since stop_rx() requires that the
port->lock is taken and interrupts are disabled, the start_rx()
callback has the same requirement.
Fixes: cfab87c2c2 ("serial: core: Introduce callback for start_rx and do stop_rx in suspend only if this callback implementation is present.")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230525093159.223817-5-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uarts_ops stop_rx() callback expects that the port->lock is
taken and interrupts are disabled.
Fixes: 1fe0e1fa32 ("serial: 8250_omap: Handle optional overrun-throttle-ms property")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230525093159.223817-4-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uarts_ops stop_rx() callback expects that the port->lock is
taken and interrupts are disabled.
Fixes: c9d2325cdb ("serial: core: Do stop_rx in suspend path for console if console_suspend is disabled")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230525093159.223817-3-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_ops startup() callback is called without interrupts
disabled and without port->lock locked, relatively late during the
boot process (from the call path of console_on_rootfs()). If the
device is a console, it was already previously registered and could
be actively printing messages.
The console printing function serial8250_console_write() modifies
the interrupt register (UART_IER) under the port->lock with the
pattern: read, clear, restore.
Since some startup() callbacks are modifying UART_IER without the
port->lock locked, it is possible that the value intended to be
written by the startup() callback will get overwritten and be
lost.
CPU0 CPU1
serial8250_console_write omap_8250_startup
-------------------------- -----------------
spin_lock(port->lock)
oldval = read(UART_IER)
uart_console_write()
write(newval, UART_IER)
write(oldval, UART_IER)
spin_unlock(port->lock)
Add port->lock synchronization to the 8250 startup() callbacks
where they need to access UART_IER. This avoids racing with
serial8250_console_write().
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230525093159.223817-2-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver have a race, experienced only with PREEMPT_RT patchset:
CPU0 | CPU1
==================================================================
qcom_geni_serial_probe |
uart_add_one_port |
| serdev_drv_probe
| qca_serdev_probe
| serdev_device_open
| uart_open
| uart_startup
| qcom_geni_serial_startup
| enable_irq
| __irq_startup
| WARN_ON()
| IRQ not activated
request_threaded_irq |
irq_domain_activate_irq |
The warning:
894000.serial: ttyHS1 at MMIO 0x894000 (irq = 144, base_baud = 0) is a MSM
serial serial0: tty port ttyHS1 registered
WARNING: CPU: 7 PID: 107 at kernel/irq/chip.c:241 __irq_startup+0x78/0xd8
...
qcom_geni_serial 894000.serial: serial engine reports 0 RX bytes in!
Adding UART port triggers probe of child serial devices - serdev and
eventually Qualcomm Bluetooth hci_qca driver. This opens UART port
which enables the interrupt before it got activated in
request_threaded_irq(). The issue originates in commit f3974413cf
("tty: serial: qcom_geni_serial: Wakeup IRQ cleanup") and discussion on
mailing list [1]. However the above commit does not explain why the
uart_add_one_port() is moved above requesting interrupt.
[1] https://lore.kernel.org/all/5d9f3dfa.1c69fb81.84c4b.30bf@mx.google.com/
Fixes: f3974413cf ("tty: serial: qcom_geni_serial: Wakeup IRQ cleanup")
Cc: <stable@vger.kernel.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230505152301.2181270-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports:
drivers/tty/serial/8250/8250_bcm7271.c:1120 brcmuart_probe() warn:
'baud_mux_clk' from clk_prepare_enable() not released on lines: 1032.
The issue is fixed by using a managed clock.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Reported-by: XuDong Liu <m202071377@hust.edu.cn>
Link: https://lore.kernel.org/lkml/20230424125100.4783-1-m202071377@hust.edu.cn/
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230427181916.2983697-3-opendmb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports:
drivers/tty/serial/arc_uart.c:631 arc_serial_probe() warn:
'port->membase' from of_iomap() not released on lines: 631.
In arc_serial_probe(), if uart_add_one_port() fails,
port->membase is not released, which would cause a resource leak.
To fix this, I replace of_iomap with devm_platform_ioremap_resource.
Fixes: 8dbe1d5e09 ("serial/arc: inline the probe helper")
Signed-off-by: Ke Zhang <m202171830@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230428031636.44642-1-m202171830@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With W=1:
drivers/tty/serial/8250/8250_port.c:679: warning: Function parameter or member 'termios' not described in 'serial8250_em485_config'
Fix this by documenting the parameter.
Fixes: ae50bb2752 ("serial: take termios_rwsem for ->rs485_config() & pass termios as param")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/2bd1e62be1d5d33333002910372feecc6d52e78f.1682071013.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Advantech PCI-1611U card
Advantech provides opensource drivers for this and many others card
based on legacy copy of 8250_pci driver called adv950
https://www.advantech.com/emt/support/details/driver?id=1-TDOIMJ
It is hard to maintain to run as out of tree module on newer kernels.
Just adding PCI ID to kernel 8250_pci works perfect.
Signed-off-by: Vitaliy Tomin <tomin@iszf.irk.ru>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230423034512.2671157-1-tomin@iszf.irk.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Possibly the last PCI controller-based (i.e. not a soft/winmodem)
dial-up modem one can still buy.
Looks to have a stock XR17C154 PCI UART chip for communication, but for
some reason when provisioning the PCI IDs they swapped the vendor and
subvendor IDs. Otherwise this card would have worked out of the box.
Searching online, some folks seem to not have this issue and others do,
so it is possible only some batches of cards have this error.
Create a new macro to handle the switched IDs and add support here.
Signed-off-by: Andrew Davis <afd@ti.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230420160209.28221-1-afd@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value is only ever used as a return value for remove callbacks
of platform drivers. This return value is ignored by the driver core.
(The only effect is an error message, but uart_remove_one_port() already
emitted one in this case.)
So the return value isn't used at all and uart_remove_one_port() can be
changed to return void without any loss. Also this better matches the
Linux device model as remove functions are not supposed to fail.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512173810.131447-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Returning early from stm32_usart_serial_remove() results in a resource
leak as several cleanup functions are not called. The driver core ignores
the return value and there is no possibility to clean up later.
uart_remove_one_port() only returns non-zero if there is some
inconsistency (i.e. stm32_usart_driver.state[port->line].uart_port == NULL).
This should never happen, and even if it does it's a bad idea to exit
early in the remove callback without cleaning up.
This prepares changing the prototype of struct platform_driver::remove to
return void. See commit 5c5a7680e6 ("platform: Provide a remove callback
that returns no value") for further details about this quest.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512173810.131447-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As unmapped registers are at the tail of the array, the ARRAY_SIZE()
condition will catch them just fine. No need to define special
value for them.
Convert the arrays to u8 as all entiries are now positive.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230511121029.13128-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A non-trivial amount of RT288x/Au1xxx code is encapsulated into
ifdeffery in 8250_port / 8250_early and some if UPIO_AU blocks.
Create a separate file from them.
Also handle errors properly in the cases where RT288x/Au1xxx code is
not configured.
It seems that 0x1000 mapsize is likely overkill but I've kept it the
same as previously (the value was shrunk to that value in commit
b2b13cdfd0 ("SERIAL 8250: Fixes for Alchemy UARTs.")). Seemingly, the
driver only needs to access register at 0x28 for the divisor latch.
The Kconfig side is a bit tricky. As SERIAL_8250_RT288X is bool it can
only be =y. It is possible to have SERIAL_8250=m + SERIAL_8250_RT288X=y
which required altering when 8250/ is included or the rt288x would not
be built.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230511121029.13128-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add mapsize, bugs, and divisor latch read/write functions
(->dl_read/write()) into plat_serial8250_port to carry the setup
necessary for RT288x/Au1xxx devices over to uart port.
Document the added members with kerneldoc style but do not enable
kerneldoc yet as there are many fields which remain undocumented.
While at it, convert .bugs in struct uart_8250_port to u16 to match it
with the type used in struct plat_serial8250_port.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230511121029.13128-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Divisor latch read/write functions currently handle the value is int.
As the value is related to HW context, u32 makes much more sense than a
signed type.
While at it, name the parameters in the callback signature.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230511121029.13128-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already allocate CONFIG_SERIAL_8250_NR_UARTS, but only allow using
CONFIG_SERIAL_8250_RUNTIME_UARTS uarts unless nr_uarts module params
is set. This causes issues for using distro kernels on SoCs with a
large number of serial ports.
Let's allow up to CONFIG_SERIAL_8250_NR_UARTS instead. To do this, we init
the ports as needed if the initial uarts was too low. This way there's no
need to set the value for CONFIG_SERIAL_8250_RUNTIME_UARTS to some SoC
specific higher value. Typically the default value of 4 can be used as
set for legacy reasons.
Note that limiting the number of intial uarts still works as before
unless a serial console on a higher port is specified. In this case we
will increase the nr_ports up to the console port specified.
Suggested-by: Andrew Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230508111903.39339-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unbinding the console uart, we want to power down the uart hardware
on remove. For the console uart, the normal shutdown path will never get
called as the cons_filp stays open. Let's rearrange the dma related
functions a bit so we can call driver shutdown also on console uart rebind.
Currently we set up->dma on probe, but that causes issues calling
omap_8250_shutdown() on remove. The dma startup will not get called on
the next rebind as we still have up->dma set from probe.
Note that serial8250_release_dma() already checks for dma so we can
remove the check for it in 8205_omap driver.
With these changes we also avoid hogging dma virtual channels for the
unused uarts that may be limited on some devices.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230508082014.23083-5-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have the struct uart_8250_port instance recycled on device rebind while
the struct omap8250_priv instance is not. For the console uart,
__tty_hangup() does not call tty->ops->hangup() as cons_filp stays open,
and uart shutdown won't get called. This means we have a stale
priv->wakeirq handler around after unbind, and port->irq is not freed on
unbind.
There's no need to claim the interrupts on startup. We can fix this and
simplify the driver a bit by claiming the interrupts in probe, and clearing
them on remove. For the device interrupt, we can use devm_request_irq().
To do this, we change omap8250_irq() to use struct omap8250_priv data
directly so we don't have to wait for the assigned port from
serial8250_register_8250_port().
We must also drop IRQF_SHARED to set IRQ_NOAUTOEN to avoid spurious
interrupts until the port has been registered. There's no need for
IRQF_SHARED for 8250_omap, the serial port interrupt lines are dedicated
lines.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230508082014.23083-4-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We must idle the uart only after serial8250_unregister_port(). Otherwise
unbinding the uart via sysfs while doing cat on the port produces an
imprecise external abort:
mem_serial_in from omap_8250_pm+0x44/0xf4
omap_8250_pm from uart_hangup+0xe0/0x194
uart_hangup from __tty_hangup.part.0+0x37c/0x3a8
__tty_hangup.part.0 from uart_remove_one_port+0x9c/0x22c
uart_remove_one_port from serial8250_unregister_port+0x60/0xe8
serial8250_unregister_port from omap8250_remove+0x6c/0xd0
omap8250_remove from platform_remove+0x28/0x54
Turns out the driver needs to have runtime PM functional before the
driver probe calls serial8250_register_8250_port(). And it needs
runtime PM after driver remove calls serial8250_unregister_port().
On probe, we need to read registers before registering the port in
omap_serial_fill_features_erratas(). We do that with custom uart_read()
already.
On remove, after serial8250_unregister_port(), we need to write to the
uart registers to idle the device. Let's add a custom uart_write() for
that.
Currently the uart register access depends on port->membase to be
initialized, which won't work after serial8250_unregister_port().
Let's use priv->membase instead, and use it for runtime PM related
functions to remove the dependency to port->membase for early and
late register access.
Note that during use, we need to check for a valid port in the runtime PM
related functions. This is needed for the optional wakeup configuration.
We now need to set the drvdata a bit earlier so it's available for the
runtime PM functions.
With the port checks in runtime PM functions, the old checks for priv in
omap8250_runtime_suspend() and omap8250_runtime_resume() functions are no
longer needed and are removed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230508082014.23083-3-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If serial8250_register_8250_port() fails, the SoC can hang as the
deferred PMQoS work will still run as is not flushed and removed.
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230508082014.23083-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART011_CR_RXE is set in pl011_startup() during normal initialization, and
cleared by pl011_disable_uart() during port shutdown.
You can use a none-console port in poll mode like kgdboc does with
tty_find_polling_driver() after a port shutdown. But pl011_startup() is not
called in tty_find_polling_driver(). So you need to set UART011_CR_RXE to
reenable receive function.
Not sure setting UART011_CR_RXE in pl011_set_termios() is a good idea
through.
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Link: https://lore.kernel.org/r/20230501070909.1144547-1-xiehongyu1@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA transfer may end prematurely due to the DMA Rx timeout even during an
active transfer because a constant timeout does not accurately simulate an
EOP (End Of Package) event. This patch uses a timer to simulate the
hardware EOP event. The timer should only complete a DMA transfer once the
idle period satisfies a specified interval which is baud rate dependent.
The problem has been observed with low baud rates but could occur also
with high baud rates.
Make the DMA Rx timeout baud rate dependent and check the DMA residue count
before copying data to the TTY buffer. If the residue count remains
unchanged since the last interrupt, that indicates no new data was
received. In this case, the DMA should complete as an EOP event. Otherwise,
new data was received during the interval and the EOP condition is not met
so restart the DMA Rx timeout
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230510203359.1353469-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of tty/serial driver updates for 6.4-rc1.
Nothing major, just lots of tiny, constant, forward development. This
includes:
- obligatory n_gsm updates and feature additions
- 8250_em driver updates
- sh-sci driver updates
- dts cleanups and updates
- general cleanups and improvements by Ilpo and Jiri
- other small serial driver core fixes and driver updates
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEqB7w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylQuwCgwU9bGoihDtFsoFYUra/FKPPoC88Anj6t1a1f
X5HZmADnwrFNNq/jP4vH
=FeNF
-----END PGP SIGNATURE-----
Merge tag 'tty-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty/serial driver updates for 6.4-rc1.
Nothing major, just lots of tiny, constant, forward development. This
includes:
- obligatory n_gsm updates and feature additions
- 8250_em driver updates
- sh-sci driver updates
- dts cleanups and updates
- general cleanups and improvements by Ilpo and Jiri
- other small serial driver core fixes and driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (87 commits)
n_gsm: Use array_index_nospec() with index that comes from userspace
tty: vt: drop checks for undefined VT_SINGLE_DRIVER
tty: vt: distribute EXPORT_SYMBOL()
tty: vt: simplify some cases in tioclinux()
tty: vt: reformat tioclinux()
tty: serial: sh-sci: Fix end of transmission on SCI
tty: serial: sh-sci: Add support for tx end interrupt handling
tty: serial: sh-sci: Fix TE setting on SCI IP
tty: serial: sh-sci: Add RZ/G2L SCIFA DMA rx support
tty: serial: sh-sci: Add RZ/G2L SCIFA DMA tx support
serial: max310x: fix IO data corruption in batched operations
serial: core: Disable uart_start() on uart_remove_one_port()
serial: 8250: Reinit port->pm on port specific driver unbind
serial: 8250: Add missing wakeup event reporting
tty: serial: fsl_lpuart: use UARTMODIR register bits for lpuart32 platform
tty: serial: fsl_lpuart: adjust buffer length to the intended size
serial: fix TIOCSRS485 locking
serial: make SiFive serial drivers depend on ARCH_ symbols
tty: synclink_gt: don't allocate and pass dummy flags
tty: serial: simplify qcom_geni_serial_send_chunk_fifo()
...
Merge ACPI bus type driver changes, ACPI backlight driver updates and a
series of cleanups related to of.h for 6.4-rc1:
- Ensure that ACPI notify handlers are not running after removal and
clean up code in acpi_sb_notify() (Rafael Wysocki).
- Remove register_backlight_delay module option and code and remove
quirks for false-positive backlight control support advertised on
desktop boards (Hans de Goede).
- Replace irqdomain.h include with struct declarations in ACPI headers
and update several pieces of code previously including of.h
implicitly through those headers (Rob Herring).
* acpi-bus:
ACPI: bus: Ensure that notify handlers are not running after removal
ACPI: bus: Add missing braces to acpi_sb_notify()
* acpi-video:
ACPI: video: Remove desktops without backlight DMI quirks
ACPI: video: Remove register_backlight_delay module option and code
* acpi-misc:
ACPI: Replace irqdomain.h include with struct declarations
fpga: lattice-sysconfig-spi: Add explicit include for of.h
tpm: atmel: Add explicit include for of.h
virtio-mmio: Add explicit include for of.h
pata: ixp4xx: Add explicit include for of.h
ata: pata_macio: Add explicit include of irqdomain.h
serial: 8250_tegra: Add explicit include for of.h
net: rfkill-gpio: Add explicit include for of.h
staging: iio: resolver: ad2s1210: Add explicit include for of.h
iio: adc: ad7292: Add explicit include for of.h
We need to set TE to "0" (i.e., disable serial transmission) to
get the expected behavior of the end of serial transmission.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-6-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section
23.3.7 Serial Data Transmission (Asynchronous Mode), it is mentioned
that, set the SCR.TIE bit to 0 and SCR.TEIE bit to 1, after the last
data to be transmitted are written to the TDR.
This will generate tx end interrupt and in the handler set SCR.TE and
SCR.TEIE to 0.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section
23.3.7 Serial Data Transmission (Asynchronous Mode) it is mentioned
that the TE (transmit enable) must be set after setting TIE (transmit
interrupt enable) or these 2 bits are set to 1 simultaneously by a
single instruction. So set these 2 bits in single instruction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-4-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked. Similarly clearing DMARS register makes signal to work as
interrupt signal and subsequent interrupt requests to the interrupt
controller are unmasked.
Add SCIFA DMA rx support for RZ/G2L alike SoCs by disabling RXI line
interrupt and setting DMARS registers by DMA api for DMA transfer request.
Apart from this, we must set FIFO trigger to 1 for the expected behavior
of the receive transmission.
While at it replace the parameter irq to s->irqs[SCIx_RXI_IRQ] in
disable_irq_nosync() to match enable_irq() in sci_dma_rx_reenable_irq().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked. Similarly clearing DMARS register makes signal to work as
interrupt signal and subsequent interrupt requests to the interrupt
controller are unmasked.
Add SCIFA DMA tx support for RZ/G2L alike SoCs by disabling TXI line
interrupt and setting DMARS registers by DMA api for DMA transfer request.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After upgrading from 5.16 to 6.1, our board with a MAX14830 started
producing lots of garbage data over UART. Bisection pointed out commit
285e76fc04 as the culprit. That patch tried to replace hand-written
code which I added in 2b4bac48c1 ("serial: max310x: Use batched reads
when reasonably safe") with the generic regmap infrastructure for
batched operations.
Unfortunately, the `regmap_raw_read` and `regmap_raw_write` which were
used are actually functions which perform IO over *multiple* registers.
That's not what is needed for accessing these Tx/Rx FIFOs; the
appropriate functions are the `_noinc_` versions, not the `_raw_` ones.
Fix this regression by using `regmap_noinc_read()` and
`regmap_noinc_write()` along with the necessary `regmap_config` setup;
with this patch in place, our board communicates happily again. Since
our board uses SPI for talking to this chip, the I2C part is completely
untested.
Fixes: 285e76fc04 ("serial: max310x: use regmap methods for SPI batch operations")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/79db8e82aadb0e174bc82b9996423c3503c8fb37.1680732084.git.jan.kundrat@cesnet.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While rebinding a uart device in a loop I noticed we may see a tx related
race on uart_remove_one_port():
uart_write from n_tty_write
n_tty_write from file_tty_write.constprop.0
file_tty_write.constprop.0 from vfs_write
vfs_write from ksys_write
ksys_write from ret_fast_syscall
Let's disallow tx on port->UPF_DEAD. This flag gets set before we start
tearing down the port in uart_remove_one_port().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230419115423.59957-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we unbind a serial port hardware specific 8250 driver, the generic
serial8250 driver takes over the port. After that we see an oops about 10
seconds later. This can produce the following at least on some TI SoCs:
Unhandled fault: imprecise external abort (0x1406)
Internal error: : 1406 [#1] SMP ARM
Turns out that we may still have the serial port hardware specific driver
port->pm in use, and serial8250_pm() tries to call it after the port
specific driver is gone:
serial8250_pm [8250_base] from uart_change_pm+0x54/0x8c [serial_base]
uart_change_pm [serial_base] from uart_hangup+0x154/0x198 [serial_base]
uart_hangup [serial_base] from __tty_hangup.part.0+0x328/0x37c
__tty_hangup.part.0 from disassociate_ctty+0x154/0x20c
disassociate_ctty from do_exit+0x744/0xaac
do_exit from do_group_exit+0x40/0x8c
do_group_exit from __wake_up_parent+0x0/0x1c
Let's fix the issue by calling serial8250_set_defaults() in
serial8250_unregister_port(). This will set the port back to using
the serial8250 default functions, and sets the port->pm to point to
serial8250_pm.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230418101407.12403-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An 8250 UART configured as a wake-up source would not have reported
itself through sysfs as being the source of wake-up, correct that.
Fixes: b3b708fa27 ("wake up from a serial port")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230414170241.2016255-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For lpuart32 platforms, UARTMODIR register is used instead of UARTMODEM.
So here should configure the corresponding UARTMODIR register bits to
avoid confusion.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230414022111.20896-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the fls function definition provided below, we should not
subtract 1 to obtain the correct buffer length:
fls(0) = 0, fls(1) = 1, fls(0x80000000) = 32.
Fixes: 5887ad43ee ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20230410195555.1003900-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RS485 multipoint addressing support for some reason added a new
ADDRB termios cflag which is (only!) updated from one of the RS485
ioctls.
Make sure to take the termios rw semaphore for the right ioctl (i.e.
set, not get).
Fixes: ae50bb2752 ("serial: take termios_rwsem for ->rs485_config() & pass termios as param")
Cc: stable@vger.kernel.org # 6.0
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20230412124811.11217-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the
use of such symbols on other architectures, convert the SiFive serial
driver Kconfig entries from the SOC_ symbols to ARCH_ instead.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230406-carnival-aspirate-fcf69a30078c@spud
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* use memcpy() instead of the loop (removes c variable)
* use remaining parameter directly (removes chunk variable)
The code is simpler and easier to follow.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230420093514.13055-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With linux/acpi.h no longer implicitly including of.h, add an explicit
include of of.h to fix the following error:
drivers/tty/serial/8250/8250_tegra.c:68:15: error: implicit declaration of function 'of_alias_get_id' [-Werror=implicit-function-declaration]
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
SCI IP on RZ/G2L alike SoCs do not need regshift compared to other SCI
IPs on the SH platform. Currently, it does regshift and configuring Rx
wrongly. Drop adding regshift for RZ/G2L alike SoCs.
Fixes: dfc80387ae ("serial: sh-sci: Compute the regshift value for SCI ports")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230321114753.75038-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For serdev framework, tty->dev is a NULL pointer, lpuart_uport_is_active
calling device_may_wakeup() may cause kernel NULL pointer crash, so here
add the NULL pointer check before using it.
Fixes: 4f5cb8c5e9 ("tty: serial: fsl_lpuart: enable wakeup source for lpuart")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230323110923.24581-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to avoid
checking for transmission complete when UARTCTRL_SBK is asserted,
otherwise the lpuart32_tx_empty may never get TIOCSER_TEMT.
Commit 2411fd94ceaa("tty: serial: fsl_lpuart: skip waiting for
transmission complete when UARTCTRL_SBK is asserted") only fix it in
lpuart32_set_termios(), here also fix it in lpuart32_tx_empty().
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230323054415.20363-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede reported Bluetooth adapters (HCIs) connected over an UART
connection failed due corrupted Rx payload. The problem was narrowed
down to DMA Rx starting on UART_IIR_THRI interrupt. The problem occurs
despite LSR having DR bit set, which is precondition for attempting to
start DMA Rx in the first place.
From a debug patch:
[x.807834] 8250irq: iir=cc lsr+saved=60 received=0/15 ier=0f dma_t/rx/err=0/0/0
[x.808676] 8250irq: iir=c2 lsr+saved=61 received=0/0 ier=0f dma_t/rx/err=0/0/0
[x.808776] 8250irq: iir=cc lsr+saved=60 received=1/12 ier=0d dma_t/rx/err=0/1/0
[x.808870] Bluetooth: hci0: Frame reassembly failed (-84)
In the debug snippet, received field indicates 1 byte was transferred
over DMA and 12 bytes after that with the non-DMA Rx. The sole byte DMA
handled was corrupted (gets zeroed) which leads to the HCI failure.
This problem became apparent after commit e8ffbb71f7 ("serial: 8250:
use THRE & __stop_tx also with DMA") changed Tx stop behavior. Tx stop
is now triggered from a THRI interrupt.
Despite that this problem looks like a HW bug, this fix is not adding
UART_BUG_xx flag to the driver beucase it seems useful in general to
avoid starting DMA when there are only a few bytes to transfer.
Skipping DMA for small transfers avoids the extra overhead DMA incurs.
Thus, don't setup DMA Rx on UART_IIR_THRI but leave it to a subsequent
interrupt which has Rx a related IIR value.
By returning false from handle_rx_dma(), the DMA vs non-DMA decision is
postponed until either UART_IIR_RDI (FIFO threshold worth of bytes
awaiting) or UART_IIR_TIMEOUT (inter-character timeout) triggers at a
later time which allows better to discern whether the number of bytes
warrants starting DMA or not.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Fixes: e8ffbb71f7 ("serial: 8250: use THRE & __stop_tx also with DMA")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230317103034.12881-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fourth interrupt on SCI port is transmit end interrupt compared to
the break interrupt on other port types. So, shuffle the interrupts to fix
the transmit end interrupt handler.
Fixes: e1d0be6161 ("sh-sci: Add h8300 SCI")
Cc: stable <stable@kernel.org>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230317150403.154094-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a potential race before THRE/TEMT deasserts when DMA Tx is
starting up (or the next batch of continuous Tx is being submitted).
This can lead to misdetecting Tx empty condition.
It is entirely normal for THRE/TEMT to be set for some time after the
DMA Tx had been setup in serial8250_tx_dma(). As Tx side is definitely
not empty at that point, it seems incorrect for serial8250_tx_empty()
claim Tx is empty.
Fix the race by also checking in serial8250_tx_empty() whether there's
DMA Tx active.
Note: This fix only addresses in-kernel race mainly to make using
TCSADRAIN/FLUSH robust. Userspace can still cause other races but they
seem userspace concurrency control problems.
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230317113318.31327-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit b984d7b56d ("MIPS: sibyte: Remove unused config option
SIBYTE_BCM1x55"), an #if in the Broadcom SiByte DUART driver can be
simplified.
Simplify the prepreprocessor condition after config SIBYTE_BCM1x55 removal.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230323071053.417-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty framework can support polling console to allow operation
in situations where interrupts are turned off. Adding polling mode
support allows using KGDB over serial console,
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/20230322223956.84647-1-arend.vanspriel@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The direction field in the DMA config is deprecated. The sh-sci driver
sets {src,dst}_{addr,addr_width} based on the DMA direction and
it results in dmaengine_slave_config() failure as RZ DMAC driver
validates {src,dst}_addr_width values independent of DMA direction.
Fix this issue by passing both {src,dst}_{addr,addr_width}
values independent of DMA direction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230322074717.6057-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1ea35b3557 ("ARM: s3c: remove s3c24xx specific hacks"), allows
simplifying the whole config logic for SERIAL_SAMSUNG_UARTS, and did this
config simplification. However, it misses that SERIAL_SAMSUNG_UARTS_4's
effect was just to control SERIAL_SAMSUNG_UARTS, and with the commit's
change, the config SERIAL_SAMSUNG_UARTS_4 has no remaining effect and can
be deleted.
Remove this obsolete config SERIAL_SAMSUNG_UARTS_4.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230317071538.29366-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On sc7180 Chromebooks, I did the following:
* Didn't enable earlycon in the kernel command line.
* Didn't enable serial console in the kernel command line.
* Didn't enable an agetty or any other client of "/dev/ttyMSM0".
* Added "kgdboc=ttyMSM0" to the kernel command line.
After I did that, I tried to enter kdb with this command over an ssh
session:
echo g > /proc/sysrq-trigger
When I did that the system just hung.
Although I thought I'd tested this scenario before, I couldn't go back
and find a time when it was working. Previous testing must have relied
on either the UART acting as the kernel console or an agetty running.
It turns out to be pretty easy to fix: we can just use
qcom_geni_serial_port_setup() as the .poll_init() function. This,
together with the patch ("serial: uart_poll_init() should power on the
UART"), allows the debugger to work even if there are no other users
of the serial port.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316132027.RESEND.2.Ie678853bb101091afe78cc8c22344bf3ff3aed74@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Qualcomm devices which use the "geni" serial driver, kdb/kgdb won't
be very happy if you use it but the resources of the port haven't been
powered on. Today kdb/kgdb rely on someone else powering the port
on. This could be the normal kernel console or an agetty running.
Let's fix this to explicitly power things on when setting up a polling
driver.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316132027.RESEND.1.I106c39498d8094c6f5e7ada42c7db17aa5c64e48@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the tty/serial fixes in here and it resolves a merge conflict
with:
drivers/tty/serial/8250/8250_em.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty and serial driver fixes for 6.3-rc3 to resolve
some reported issues.
They include:
- 8250 driver Kconfig issue pointed out by you that showed up in -rc1
- qcom-geni serial driver fixes
- various 8250 driver fixes for reported problems
- fsl_lpuart driver fixes
- serdev fix for regression in -rc1
- vt.c bugfix
All have been in linux-next for over a week with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZBcinQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynIYACgjP49Xy1N6hDLZJgKxvnPLmvnhY4AoKM8CkHI
zbWudA1fBqsYLFtxNKaQ
=/Ond
-----END PGP SIGNATURE-----
Merge tag 'tty-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.3-rc3 to resolve
some reported issues.
They include:
- 8250 driver Kconfig issue pointed out by you that showed up in -rc1
- qcom-geni serial driver fixes
- various 8250 driver fixes for reported problems
- fsl_lpuart driver fixes
- serdev fix for regression in -rc1
- vt.c bugfix
All have been in linux-next for over a week with no reported problems"
* tag 'tty-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: vt: protect KD_FONT_OP_GET_TALL from unbound access
serial: qcom-geni: drop bogus uart_write_wakeup()
serial: qcom-geni: fix mapping of empty DMA buffer
serial: qcom-geni: fix DMA mapping leak on shutdown
serial: qcom-geni: fix console shutdown hang
serdev: Set fwnode for serdev devices
tty: serial: fsl_lpuart: fix race on RX DMA shutdown
serial: 8250_pci1xxxx: Disable SERIAL_8250_PCI1XXXX config by default
serial: 8250_fsl: fix handle_irq locking
serial: 8250_em: Fix UART port type
serial: 8250: ASPEED_VUART: select REGMAP instead of depending on it
tty: serial: fsl_lpuart: skip waiting for transmission complete when UARTCTRL_SBK is asserted
Revert "tty: serial: fsl_lpuart: adjust SERIAL_FSL_LPUART_CONSOLE config dependency"
The arbitration of the UART DMA is mishandled for a few
exceptional cases when probing and releasing the driver.
It is possible that the DMA register spaces are not defined in
device tree for an instance of the driver, so attempts to access
the registers in brcmuart_arbitration() would use NULL pointers.
It is also possible for the probe function to return an error
while still holding the UART DMA. This would prevent the UART
DMA from being claimed by an instance that could use it.
These errors are addressed by only releasing the UART DMA if it
is held by this instance (i.e. priv->dma_enabled == 1) and
directing early error paths in probe to this common release_dma
handling.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230309190224.687380-1-opendmb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hw_stopped in uart_change_line_settings() stores old hw_stopped, thus
rename it appropriately.
Alter logic to check first if the hw_stopped was changed, and then pick
which function to call if it was because the logic is more obvious that
way.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert hw_stopped in uart_port to bool because its more appropriate
type for how it is used.
Also convert the local variable in uart_change_line_settings() caching
old hw_stopped to bool.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_change_speed() changes more than just speed so rename it to more
generic uart_change_line_settings().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compare against B0 rather than assume B0 equals zero, which is true for
all archs but explicit B0 makes the code more obvious.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here).
drivers/tty/serial/sprd_serial.c:1242:34: error: ‘serial_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230310222957.315848-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/tty/serial/sh-sci.c:3144:34: error: ‘of_sci_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230310222957.315848-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230310144727.1545699-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230310144727.1545630-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/lkml/20221118224540.619276-572-uwe@kleine-koenig.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Drop the bogus uart_write_wakeup() from when setting up a new DMA
transfer, which does not free up any more space in the ring buffer.
Any pending writers will be woken up when the transfer completes.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that there is data in the ring buffer before trying to set up
a zero-length DMA transfer.
This specifically fixes the following warning when unmapping the empty
buffer on the sc8280xp-crd:
WARNING: CPU: 0 PID: 138 at drivers/iommu/dma-iommu.c:1046 iommu_dma_unmap_page+0xbc/0xd8
...
Call trace:
iommu_dma_unmap_page+0xbc/0xd8
dma_unmap_page_attrs+0x30/0x1c8
geni_se_tx_dma_unprep+0x28/0x38
qcom_geni_serial_isr+0x358/0x75c
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix what appears to be a copy-paste error that can lead to a leaked DMA
mapping on close() and failure to restart TX after the port is reopened.
Note that rx_dma_addr is generally NULL when
qcom_geni_serial_stop_tx_dma() is called as part of shutdown() (but
tx_dma_addr need not be).
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit added back the calls top stop tx and rx to shutdown()
which had previously been removed by commit e83766334f ("tty: serial:
qcom_geni_serial: No need to stop tx/rx on UART shutdown") in order to
be able to use kgdb after stopping the getty.
Not only did this again break kgdb, but it also broke serial consoles
more generally by hanging TX when stopping the getty during reboot.
The underlying problem has been there since the driver was first merged
and fixing it is going to be a bit involved so simply stop calling the
broken stop functions during shutdown for consoles for now.
Fixes: d8aca2f968 ("tty: serial: qcom-geni-serial: stop operations in progress at shutdown")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per RZ/V2M hardware manual(Rev.1.30 Jun, 2022), UART IP has a
restriction as mentioned below.
40.6.1 Point for Caution when Changing the Register Settings:
When changing the settings of the following registers, a PRESETn master
reset or FIFO reset + SW reset (FCR[2],FCR[1], HCR0[7]) must be input to
re-initialize them.
Target Registers: FCR, LCR, MCR, DLL, DLM, HCR0.
Add serial8250_em_reg_update() and serial8250_em_serial_out_helper() to
handle this restriction. serial8250_em_serial_out_helper() is identical to
previous serial8250_em_serial_out() except that UART_FCR macro is removed
from serial8250_em_serial_out_helper() as it is now handled by serial8250_
em_serial_out().
DLL/DLM register can be updated only by setting LCR[7]. So the
updation of LCR[7] will perform reset for DLL/DLM register changes.
EMMA mobile has the same register set as RZ/V2M and this patch is tested on
EMEV2 board. So, there is no harm in applying the same restriction here as
well as the HW manual for EMMA mobile is not updated for a long time.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-8-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART_FCR shares the same offset with UART_IIR. We cannot use UART_FCR
in serial8250_em_serial_in() as it overlaps with UART_IIR.
Define UART_FCR_EM macro with a high value to avoid overlapping
with existing UART_* register defines and define another macro
UART_FCR_EM_HW for the real offset.
Use these macros in serial8250_em_serial{_in/_out} function to
read/write FCR register.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-7-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify clk handling in probe() by replacing devm_clk_get()->devm_
clk_get_enabled(). This replaces the usage of clk_prepare_enable/clk_
disable_unprepare() in probe()/remove(). After that sclk is no
longer required in struct serial8250_em_priv and is replaced by a
local variable sclk in probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-6-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify probe() by using dev_err_probe() instead of dev_err() and
add a local variable 'dev' to replace '&pdev->dev'.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per HW manual for EMEV2 "R19UH0040EJ0400 Rev.4.00", the UART
IP found on EMMA mobile SoC is Register-compatible with the
general-purpose 16750 UART chip. Fix UART port type as 16750 and
enable 64-bytes fifo support.
Fixes: 22886ee968 ("serial8250-em: Emma Mobile UART driver V2")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amlogic Meson G12A (and later) SoCs also have the "divide XTAL by 2" bit
as the S4 UART controllers. Add a new compatible string for these SoCs
and enable the has_xtal_div2 flag for them.
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230307222651.2106615-3-martin.blumenstingl@googlemail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stm32_usart_transmit_chars() may be called with empty or stopped
transmit queue, and no XON/OFF character pending. This can happen at
the end of transmission, where this last call is used to either handle
the XON/XOFF x_char, or disable TX interrupt if queue is empty or
stopped.
If that occurs, do not assert the RS485 RTS/DE GPIO anymore, as the
GPIO would remain asserted past the end of transmission and that would
block the RS485 bus after the transmission.
Only assert the RS485 RTS/DE GPIO if there is either pending XON/XOFF
x_char, or at least one character in running transmit queue.
Fixes: d7c7671616 ("serial: stm32: Use TC interrupt to deassert GPIO RTS in RS485 mode")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230223042252.95480-2-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point in casting a struct uart_port to a struct imx_port
just to access the first member of the latter (a struct uart_port).
This introduces no code changes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230302115417.1860210-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From time to time DMA completion can come in the middle of DMA shutdown:
<process ctx>: <IRQ>:
lpuart32_shutdown()
lpuart_dma_shutdown()
del_timer_sync()
lpuart_dma_rx_complete()
lpuart_copy_rx_to_tty()
mod_timer()
lpuart_dma_rx_free()
When the timer fires a bit later, sport->dma_rx_desc is NULL:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
pc : lpuart_copy_rx_to_tty+0xcc/0x5bc
lr : lpuart_timer_func+0x1c/0x2c
Call trace:
lpuart_copy_rx_to_tty
lpuart_timer_func
call_timer_fn
__run_timers.part.0
run_timer_softirq
__do_softirq
__irq_exit_rcu
irq_exit
handle_domain_irq
gic_handle_irq
call_on_irq_stack
do_interrupt_handler
...
To fix this fold del_timer_sync() into lpuart_dma_rx_free() after
dmaengine_terminate_sync() to make sure timer will not be re-started in
lpuart_copy_rx_to_tty() <= lpuart_dma_rx_complete().
Fixes: 4a8588a1cf ("serial: fsl_lpuart: delete timer on shutdown")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20230309134302.74940-2-alexander.sverdlin@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 handle_irq callback is not just called from the interrupt
handler but also from a timer callback when polling (e.g. for ports
without an interrupt line). Consequently the callback must explicitly
disable interrupts to avoid a potential deadlock with another interrupt
in polled mode.
Fix up the two paths in the freescale callback that failed to re-enable
interrupts when polling.
Fixes: 853a9ae29e ("serial: 8250: fix handle_irq locking")
Cc: stable@vger.kernel.org # 5.13
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y/xYzqp4ogmOF5t0@kili
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230227085046.24282-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per HW manual for EMEV2 "R19UH0040EJ0400 Rev.4.00", the UART
IP found on EMMA mobile SoC is Register-compatible with the
general-purpose 16750 UART chip. Fix UART port type as 16750 and
enable 64-bytes fifo support.
Fixes: 22886ee968 ("serial8250-em: Emma Mobile UART driver V2")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: 8d310c9107 ("drivers/tty/serial/8250: Make Aspeed VUART SIRQ polarity configurable")
Cc: stable <stable@kernel.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Oskar Senft <osk@google.com>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20230226053953.4681-9-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to skip
waiting for transmission complete when UARTCTRL_SBK is asserted,
otherwise the kernel may stuck here.
And actually set_termios() adds transmission completion waiting to avoid
data loss or data breakage when changing the baud rate, but we don't
need to worry about this when queuing break characters.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230223093941.31790-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5779a072c2.
This results in a link error of
ld: drivers/tty/serial/earlycon.o: in function `parse_options':
drivers/tty/serial/earlycon.c:99: undefined reference to `uart_parse_earlycon'
When the config is in this state
CONFIG_SERIAL_CORE=m
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_EARLYCON=y
CONFIG_SERIAL_FSL_LPUART=m
CONFIG_SERIAL_FSL_LPUART_CONSOLE=y
Fixes: 5779a072c2 ("tty: serial: fsl_lpuart: adjust SERIAL_FSL_LPUART_CONSOLE config dependency")
Cc: stable <stable@kernel.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230226173846.236691-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work falls
into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be moved
into read-only memory (i.e. const) The recent work with Rust has
pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only making
things safer overall. This is the contuation of that work (started
last release with kobject changes) in moving struct bus_type to be
constant. We didn't quite make it for this release, but the
remaining patches will be finished up for the release after this
one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/ipdg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynL3gCgwzbcWu0So3piZyLiJKxsVo9C2EsAn3sZ9gN6
6oeFOjD3JDju3cQsfGgd
=Su6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/itAw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykJbQCfWv/J4ZElO108iHBU5mJCDagUDBgAnAtLLN6A
SEAnnokGCDtA/BNIXeES
=luRi
-----END PGP SIGNATURE-----
Merge tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
tty: n_gsm: add keep alive support
serial: imx: remove a redundant check
dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
tty: n_gsm: add TIOCMIWAIT support
tty: n_gsm: add RING/CD control support
tty: n_gsm: mark unusable ioctl structure fields accordingly
serial: imx: get rid of registers shadowing
serial: imx: refine local variables in rxint()
serial: imx: stop using USR2 in FIFO reading loop
serial: imx: remove redundant USR2 read from FIFO reading loop
serial: imx: do not break from FIFO reading loop prematurely
serial: imx: do not sysrq broken chars
serial: imx: work-around for hardware RX flood
serial: imx: factor-out common code to imx_uart_soft_reset()
serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
serial: 8250_pci1xxxx: Add driver for quad-uart support
serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
tty: pcn_uart: fix memory leak with using debugfs_lookup()
...
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate subsystem
trees, but the majority is in the same branch, in order to better handle
dependencies between the patches and avoid breaking bisection.
Unfortunately that leads to merge conflicts against other changes in the
subsystem trees, but they should all be trivial to resolve by removing
the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed. The
only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users.
-----BEGIN PGP SIGNATURE-----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=WejQ
-----END PGP SIGNATURE-----
Merge tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
cpp_check reports
drivers/tty/serial/imx.c:1207:15: style: Condition 'r_bytes>0' is always true [knownConditionTrueFalse]
if (r_bytes > 0) {
r_byte is set to
r_bytes = rx_ring->head - rx_ring->tail;
The head - tail calculation is also done by the earlier check
if (rx_ring->head <= sg_dma_len(sgl) &&
rx_ring->head > rx_ring->tail) {
so r_bytes will always be > 0, so the second check is not needed.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Link: https://lore.kernel.org/r/20230211154550.2130670-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move include/linux/qcom-geni-se.h to include/linux/soc/qcom/geni-se.h.
This removes 1 of a few remaining Qualcomm-specific headers into a more
approciate subdirectory under include/.
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Reviewed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Link: https://lore.kernel.org/r/20230203210133.3552796-1-quic_eberman@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neither registers shadowing is functionally needed as all the registers are
read-write, nor the shadowing makes much sense for speed-up, as most speed
critical reads/writes (of data Rx/Tx registers) are not shadowed anyway.
Moreover, the shadowing code is obviously pure overhead on the write path.
Get rid of the shadowing code and variables due to above considerations.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201141603.4205-1-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'rx' is chip register, similar to 'usr2', so let it be of 'u32' type as
well.
Move 'flg' to be FIFO read loop local as it's not used outside.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-8-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chip provides all the needed bits in the URXD0 register that we read
anyway for data, so get rid of reading USR2 and use only URXD0 bits
instead.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-7-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to read USR2 twice at every loop iteration: get rid of the
second read.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-6-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to prematurely break out of FIFO reading loop, and it
might cause needless reenters into ISR, so keep reading until FIFO is
empty.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-5-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not call uart_handle_sysrq_char() if we got any receive error along with
the character, as we don't want random junk to be considered a sysrq.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-4-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check if hardware Rx flood is in progress, and issue soft reset to UART to
stop the flood.
A way to reproduce the flood (checked on iMX6SX) is: open iMX UART at 9600
8N1, and from external source send 0xf0 char at 115200 8N1. In about 90% of
cases this starts a flood of "receiving" of 0xff characters by the iMX UART
that is terminated by any activity on RxD line, or could be stopped by
issuing soft reset to the UART (just stop/start of RX does not help). Note
that in essence what we did here is sending isolated start bit about 2.4
times shorter than it is to be if issued on the UART configured baud rate.
There was earlier attempt to fix similar issue in: 'commit
b38cb7d257 ("serial: imx: Disable new features of autobaud detection")',
but apparently it only gets harder to reproduce the issue after that
commit.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-3-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We perform soft reset in 2 places, slightly differently for no sufficient
reasons, so move more generic variant to a function, and re-use the code.
Out of 2 repeat counters, 10 and 100, select 10, as the code works at
interrupts disabled, and in practice the reset happens immediately.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-2-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx's quad-uart function has the capability to wake up UART
from suspend state. Enable wakeup before entering into suspend and
disable wakeup on resume.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-5-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx uart supports RS485 mode of operation in the hardware with
auto-direction control with configurable delay for releasing RTS after
the transmission. This patch adds support for the RS485 mode.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-4-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx is a PCIe switch with a multi-function endpoint on one of
its downstream ports. Quad-uart is one of the functions in the
multi-function endpoint. This driver loads for the quad-uart and
enumerates single or multiple instances of uart based on the PCIe
subsystem device ID.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-3-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230202141221.2293012-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There maybe pending USR interrupt before requesting irq, however
uart_add_one_port has not executed, so there will be kernel panic:
[ 0.795668] Unable to handle kernel NULL pointer dereference at virtual addre
ss 0000000000000080
[ 0.802701] Mem abort info:
[ 0.805367] ESR = 0x0000000096000004
[ 0.808950] EC = 0x25: DABT (current EL), IL = 32 bits
[ 0.814033] SET = 0, FnV = 0
[ 0.816950] EA = 0, S1PTW = 0
[ 0.819950] FSC = 0x04: level 0 translation fault
[ 0.824617] Data abort info:
[ 0.827367] ISV = 0, ISS = 0x00000004
[ 0.831033] CM = 0, WnR = 0
[ 0.833866] [0000000000000080] user address but active_mm is swapper
[ 0.839951] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[ 0.845953] Modules linked in:
[ 0.848869] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.1+g56321e101aca #1
[ 0.855617] Hardware name: Freescale i.MX8MP EVK (DT)
[ 0.860452] pstate: 000000c5 (nzcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.867117] pc : __imx_uart_rxint.constprop.0+0x11c/0x2c0
[ 0.872283] lr : imx_uart_int+0xf8/0x1ec
The issue only happends in the inmate linux when Jailhouse hypervisor
enabled. The test procedure is:
while true; do
jailhouse enable imx8mp.cell
jailhouse cell linux xxxx
sleep 10
jailhouse cell destroy 1
jailhouse disable
sleep 5
done
And during the upper test, press keys to the 2nd linux console.
When `jailhouse cell destroy 1`, the 2nd linux has no chance to put
the uart to a quiese state, so USR1/2 may has pending interrupts. Then
when `jailhosue cell linux xx` to start 2nd linux again, the issue
trigger.
In order to disable irqs before requesting them, both UCR1 and UCR2 irqs
should be disabled, so here fix that, disable the Ageing Timer interrupt
in UCR2 as UCR1 does.
Fixes: 8a61f0c70a ("serial: imx: Disable irqs before requesting them")
Suggested-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Link: https://lore.kernel.org/r/20230206013016.29352-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous 'commit 846651eca0 ("serial: fsl_lpuart: RS485 RTS
polariy is inverse")' only fixed the inverse issue on lpuart 8bit
platforms.
This is a follow-up patch to fix the RS485 polarity inverse
issue on lpuart 32bit platforms.
Fixes: 03895cf41d ("tty: serial: fsl_lpuart: Add support for RS-485")
Reported-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20230207162420.3647904-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The relevant history introducing serial_lsr_in() looks as follows:
$ git log --graph --oneline --boundary 9fafe733514b..df36f3e3fbb7 -- drivers/tty/serial/8250/8250_port.c
* df36f3e3fb Merge tag 'v5.19-rc3' into tty-next
|\
| * be03b0651f serial: 8250: Store to lsr_save_flags after lsr read
* | ...
* | bdb70c424d serial: 8250: Create serial_lsr_in()
* | ce338e4477 serial: 8250: Store to lsr_save_flags after lsr read
* | ...
|/
o 9fafe73351 tty: remove CMSPAR ifdefs
So the patch "serial: 8250: Store to lsr_save_flags after lsr read" was
introduced twice and in one branch it was followed up by commit
bdb70c424d ("serial: 8250: Create serial_lsr_in()") which moved
explicit lsr_saved_flags handling into a new function serial_lsr_in().
When the two branches were merged in commit df36f3e3fb, we got both,
serial_lsr_in() and the explicit lsr_saved_flags handling.
So drop the explicit lsr_saved_flags handling.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230202104501.264686-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As DMA Rx can be completed from two places, it is possible that DMA Rx
completes before DMA completion callback had a chance to complete it.
Once the previous DMA Rx has been completed, a new one can be started
on the next UART interrupt. The following race is possible
(uart_unlock_and_check_sysrq_irqrestore() replaced with
spin_unlock_irqrestore() for simplicity/clarity):
CPU0 CPU1
dma_rx_complete()
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma_flush()
__dma_rx_complete()
dma->rx_running = 0
// Complete DMA Rx
spin_unlock_irqrestore(&port->lock)
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma()
dma->rx_running = 1
// Setup a new DMA Rx
spin_unlock_irqrestore(&port->lock)
spin_lock_irqsave(&port->lock)
// sees dma->rx_running = 1
__dma_rx_complete()
dma->rx_running = 0
// Incorrectly complete
// running DMA Rx
This race seems somewhat theoretical to occur for real but handle it
correctly regardless. Check what is the DMA status before complething
anything in __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__dma_rx_complete() is called from two places:
- Through the DMA completion callback dma_rx_complete()
- From serial8250_rx_dma_flush() after IIR_RLSI or IIR_RX_TIMEOUT
The former does not hold port's lock during __dma_rx_complete() which
allows these two to race and potentially insert the same data twice.
Extend port's lock coverage in dma_rx_complete() to prevent the race
and check if the DMA Rx is still pending completion before calling
into __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting an interrupt with IRQF_ONESHOT will run the primary handler
in the hard-IRQ context even in the force-threaded mode. The
force-threaded mode is used by PREEMPT_RT in order to avoid acquiring
sleeping locks (spinlock_t) in hard-IRQ context. This combination
makes it impossible and leads to "sleeping while atomic" warnings.
Use one interrupt handler for both handlers (primary and secondary)
and drop the IRQF_ONESHOT flag which is not needed.
Fixes: e359b4411c ("serial: stm32: fix threaded interrupt handling")
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Valentin Caron <valentin.caron@foss.st.com> # V3
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230120160332.57930-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct liteuart_port keeps tracking of UART ID which is also
saved in the struct uart_port as line member. Drop the former one
and use the latter everywhere.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20230123192604.81452-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe we need to call all devm_*() first followed by
non-devm_*() calls. This is due to reversed clean up that
may happen in a wrong order otherwise. The driver currently
allocates xarray before calling
devm_platform_get_and_ioremap_resource(). While it's not an
issue in this certain case, it's still better to be pedantic.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gabriel Somlo <somlo@cmu.edu>
Link: https://lore.kernel.org/r/20230123191741.79751-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lpuart of imx8ulp is basically the same as imx7ulp, but it supports
some new features based on imx7ulp, such as it can assert the DMA
request on EOP(end-of-packet).
Here add lpuart support for imx8ulp, and rx_watermark is set to 3 as
imx8ulp RX FIFO depth is 8.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-7-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RTS watermark support for LPUART. The RX RTS_B output negates when
the number of empty words in the receive FIFO is greater or equal to
RTSWATER. Here set the RTSWATER to half of the rxfifo_size.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-6-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the growth of rx watermark, it's useful to enable the Receiver Idle
Empty function, it can assert the RDRF(Receive Data Register Full Flag)
when the receiver is idle for a number of idle characters and the FIFO
is not empty. It will generate a DMA request or interrupt, which can
avoid receive data being trapped in the RX FIFO since the number of
words received is less than the watermark.
Here set the RXIDEN as 0x3 which enable the RDRF assertion due to
partially filled FIFO when receiver is idle for 4 characters.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-5-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RXWATER value must be greater than 0 according to the LPUART
reference manual. And when the number of datawords in the receive
FIFO is greater than RXWATER, an interrupt or a DMA request is
generated, so no need to set the different value for lpuart interrupt
case and dma case. Here delete the wrong RXWATER setting for dma case
directly.
Fixes: 42b68768e5 ("serial: fsl_lpuart: DMA support for 32-bit variant")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since imx8qxp RX FIFO depth is 64 datawords, it will be better to set
the rx watermark as 31, which means when the number of datawords in the
receive FIFO(>= 32) is greater than the watermark, an interrupt or a DMA
request is generated.
Also keep the console rx watermark as 1 to make sure it responsive.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add rx_watermark parameter for struct lpuart_port to make the receive
watermark configurable for different platforms.
No function changed.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lpuart32_setup_watermark_enable() will configure the UART FIFO and
watermark, also enable the receiver and transmitter, this should be done
after the rx/tx dma steup ready.
Also add lpuart32_hw_disable() to make sure the receiver/transmitter and
interrupts are disabled during the dma steup.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130054107.9119-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Goto to the correct rollback label instead of directly returning.
Fixes: 5602cf99dc ("serial: liteuart: add IRQ support for the RX path")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20230123173857.40695-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for
serial engine DMA") renamed rx_fifo member to rf_buf which caused a
build failure when b8caf69a69 ("tty: serial: qcom-geni-serial: fix
slab-out-of-bounds on RX FIFO buffer") from tty-linus was merged into
tty-next.
Fix the member variable name.
Fixes: 7a6aa989f2 ("Merge 6.2-rc5 into tty-next")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230123173857.40695-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty and serial driver fixes for 6.2-rc5 that resolve
a number of tiny reported issues and some new device ids. They include:
- new device id for the exar serial driver
- speakup tty driver bugfix
- atmel serial driver baudrate fixup
- stm32 serial driver bugfix and then revert as the bugfix broke the
build. That will come back in a later pull request once it is all
worked out properly.
- amba-pl011 serial driver rs486 mode bugfix
- qcom_geni serial driver bugfix
Most of these have been in linux-next with no reported problems (well,
other than the build breakage which generated the revert), the new
device id passed 0-day testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY8wDQA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynGegCguB+ZpDHKt9wccrGP3h/dwT2MAm8AnAqG4bmy
Yw/cHHPt9gx+AW6RBtAL
=EymN
-----END PGP SIGNATURE-----
Merge tag 'tty-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.2-rc5 that
resolve a number of tiny reported issues and some new device ids. They
include:
- new device id for the exar serial driver
- speakup tty driver bugfix
- atmel serial driver baudrate fixup
- stm32 serial driver bugfix and then revert as the bugfix broke the
build. That will come back in a later pull request once it is all
worked out properly.
- amba-pl011 serial driver rs486 mode bugfix
- qcom_geni serial driver bugfix
Most of these have been in linux-next with no reported problems (well,
other than the build breakage which generated the revert), the new
device id passed 0-day testing"
* tag 'tty-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: exar: Add support for Sealevel 7xxxC serial cards
Revert "serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler"
tty: serial: qcom_geni: avoid duplicate struct member init
serial: atmel: fix incorrect baudrate setup
tty: fix possible null-ptr-defer in spk_ttyio_release
serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler
serial: amba-pl011: fix high priority character transmission in rs486 mode
serial: pch_uart: Pass correct sg to dma_unmap_sg()
tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer
Add support for Sealevel 7xxxC serial cards.
This patch:
* Adds IDs to recognize 7xxxC cards from Sealevel Systems.
* Updates exar_pci_probe() to set nr_ports to last two bytes of primary
dev ID for these cards.
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2301191440010.22558@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f24771b62a as it is
reported to break the build.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/202301200130.ttBiTzfO-lkp@intel.com
Fixes: f24771b62a ("serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler")
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Valentin Caron <valentin.caron@foss.st.com> # V3
Cc: Marek Vasut <marex@denx.de>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When -Woverride-init is enabled in a build, gcc points out that
qcom_geni_serial_pm_ops contains conflicting initializers:
drivers/tty/serial/qcom_geni_serial.c:1586:20: error: initialized field overwritten [-Werror=override-init]
1586 | .restore = qcom_geni_serial_sys_hib_resume,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/tty/serial/qcom_geni_serial.c:1586:20: note: (near initialization for 'qcom_geni_serial_pm_ops.restore')
drivers/tty/serial/qcom_geni_serial.c:1587:17: error: initialized field overwritten [-Werror=override-init]
1587 | .thaw = qcom_geni_serial_sys_hib_resume,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Open-code the initializers with the version that was already used,
and use the pm_sleep_ptr() method to deal with unused ones,
in place of the __maybe_unused annotation.
Fixes: 35781d8356 ("tty: serial: qcom-geni-serial: Add support for Hibernation feature")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20221215165453.1864836-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ba47f97a18 ("serial: core: remove baud_rates when serial console
setup") changed uart_set_options to select the correct baudrate
configuration based on the absolute error between requested baudrate and
available standard baudrate settings.
Prior to that commit the baudrate was selected based on which predefined
standard baudrate did not exceed the requested baudrate.
This change of selection logic was never reflected in the atmel serial
driver. Thus the comment left in the atmel serial driver is no longer
accurate.
Additionally the manual rounding up described in that comment and applied
via (quot - 1) requests an incorrect baudrate. Since uart_set_options uses
tty_termios_encode_baud_rate to determine the appropriate baudrate flags
this can cause baudrate selection to fail entirely because
tty_termios_encode_baud_rate will only select a baudrate if relative error
between requested and selected baudrate does not exceed +/-2%.
Fix that by requesting actual, exact baudrate used by the serial.
Fixes: ba47f97a18 ("serial: core: remove baud_rates when serial console setup")
Cc: stable <stable@kernel.org>
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20230109072940.202936-1-t.schramm@manjaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a Device Feature List (DFL) bus driver for the Altera
16550 implementation of UART.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Marco Pagani <marpagan@redhat.com>
Link: https://lore.kernel.org/r/20230115151447.1353428-5-matthew.gerlach@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert various parameter names for ->dtr_rts() and related functions
from onoff, on, and raise to active.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-12-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert uart_handle_cts_change() to bool which is more appropriate
than unsigned int.
Rename status to active to better describe what the parameter means.
While at it, make the comment about the active parameter easier to
parse.
Cleanup callsites from operations that are not necessary with bool.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-10-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert status parameter for ->dcd_change() and
uart_handle_dcd_change() to bool which matches to how the parameter is
used.
Rename status to active to better describe what the parameter means.
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the raise/on parameter in ->dtr_rts() to bool through the
callchain. The parameter is used like bool. In USB serial, there
remains a few implicit bool -> larger type conversions because some
devices use u8 in their control messages.
In moxa_tiocmget(), dtr variable was reused for line status which
requires int so use a separate variable for status.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return boolean from ->carrier_raised() instead of 0 and 1. Make the
return type change also to tty_port_carrier_raised() that makes the
->carrier_raised() call (+ cd variable in moxa into which its return
value is stored).
Also cleans up a few unnecessary constructs related to this change:
return xx ? 1 : 0;
-> return xx;
if (xx)
return 1;
return 0;
-> return xx;
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert init_hw parameter in uart_startup() and uart_port_startup() to
bool as code treats them like bool.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the devm_clk_get() may return ERR_PTR, its return value needs to be
checked to avoid invalid poineter dereference.
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221125093832.33386-1-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a RX_DURING_TX GPIO is defined by the DT property "rs485-rx-during-tx-gpios"
this patch switches this GPIO accordingly to the RS485 flag RX_DURING_TX in user
space. Controlled by this GPIO, now the hardware is responsible for connecting
or disconnecting RX during TX.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20221202104127.122761-4-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a RX_DURING_TX GPIO is defined by the DT property "rs485-rx-during-tx-gpios"
this patch switches this GPIO accordingly to the RS485 flag RX_DURING_TX in user
space. In addition, the i.MX UART receiver is no longer turned on and off during
sending, because now the hardware is responsible for connecting or disconnecting
RX during TX controlled by this GPIO.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20221202104127.122761-3-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides a generic GPIO variable for outputting the state
of RS485 RX_DURING_TX. The GPIO is defined by the devicetree property
"rs485-rx-during-tx-gpios". To use it in a low level serial driver,
the evaluation of this variable must be implemented there accordingly.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20221202104127.122761-2-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing clk_disable_unprepare() before return from
tegra_uart_hw_init() in the error handling path.
When request_irq() fails in tegra_uart_startup(), 'tup->uart_clk'
has been enabled, fix it by adding clk_disable_unprepare().
Fixes: cc9ca4d958 ("serial: tegra: Only print FIFO error message when an error occurs")
Fixes: d781ec21ba ("serial: tegra: report clk rate errors")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Link: https://lore.kernel.org/r/20221126020852.113378-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO controller component of the sc16is7xx driver is setup too
early, which can result in a race condition where another device tries
to utilise the GPIO lines before the sc16is7xx device has finished
initialising.
This issue manifests itself as an Oops when the GPIO lines are configured:
Unable to handle kernel read from unreadable memory at virtual address
...
pc : sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
lr : sc16is7xx_gpio_direction_output+0x4c/0x108 [sc16is7xx]
...
Call trace:
sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
gpiod_direction_output_raw_commit+0x64/0x318
gpiod_direction_output+0xb0/0x170
create_gpio_led+0xec/0x198
gpio_led_probe+0x16c/0x4f0
platform_drv_probe+0x5c/0xb0
really_probe+0xe8/0x448
driver_probe_device+0xe8/0x138
__device_attach_driver+0x94/0x118
bus_for_each_drv+0x8c/0xe0
__device_attach+0x100/0x1b8
device_initial_probe+0x28/0x38
bus_probe_device+0xa4/0xb0
deferred_probe_work_func+0x90/0xe0
process_one_work+0x1c4/0x480
worker_thread+0x54/0x430
kthread+0x138/0x150
ret_from_fork+0x10/0x1c
This patch moves the setup of the GPIO controller functions to later in the
probe function, ensuring the sc16is7xx device has already finished
initialising by the time other devices try to make use of the GPIO lines.
The error handling has also been reordered to reflect the new
initialisation order.
Co-developed-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Isaac True <isaac.true@canonical.com>
Link: https://lore.kernel.org/r/20221130105529.698385-1-isaac.true@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ucc_uart_probe(), we have added proper of_node_put() in the failure
paths. However, we miss it before we free *qe_port* in the remove() function.
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20221205085437.1163682-1-windhl@126.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The qcom-geni-serial driver currently only works in SE FIFO mode. This
limits the UART speed to around 180 kB/s. In order to achieve higher
speeds we need to use SE DMA mode.
Keep the console port working in FIFO mode but extend the code to use DMA
for the high-speed port.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-15-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of checking the device compatible in probe(), assign the
device-specific data to struct of_device_id. We'll use it later when
providing SE DMA support.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-13-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value of the handle_rx() callback is never checked. Drop it.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-12-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shuffle the code a bit, drop unneeded variables, make types of others
more consistent and use uart_xmit_advance() instead of handling
tail->xmit manually.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-11-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qcom_geni_serial_handle_tx() is pretty big, let's move the code that
handles the actual writing of data to a separate function which makes
sense in preparation for introducing a dma variant of handle_tx().
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-10-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove stray newlines around #ifdefs for consistency with the rest
of the driver code.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-7-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The member we want to resolve in struct qcom_geni_serial_port is called
uport so we don't need an additional redundant parameter in this macro.
While at it: turn the macro into a static inline function.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-6-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop all unused symbols from the driver.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-4-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we shuffle the code a bit, we can drop all forward definitions of
various static functions.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-3-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't stop transmissions in progress at shutdown. This is fine with
FIFO SE mode but with DMA (support for which we'll introduce later) it
causes trouble so fix it now.
Fixes: e83766334f ("tty: serial: qcom_geni_serial: No need to stop tx/rx on UART shutdown")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-2-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment in imx_uart_shutdown() says to disable the break condition,
but it doesn't actually do that, here fix this by disabling UCR1_SNDBRK
when closing the uart port like other uart drivers do.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221214031137.28815-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Need to disable the break condition for lpuart driver when closing
the uart port like other uart drivers do.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221214031137.28815-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPUART IP has a bug that it treats the CTS as higher priority than the
break signal, which cause the break signal sending through UARTCTRL_SBK
may impacted by the CTS input if the HW flow control is enabled.
Add this workaround patch to fix the IP bug, we can disable CTS before
asserting SBK to avoid any interference from CTS, and re-enable it when
break off.
Such as for the bluetooth chip power save feature, host can let the BT
chip get into sleep state by sending a UART break signal, and wake it up
by turning off the UART break. If the BT chip enters the sleep mode
successfully, it will pull up the CTS line, if the BT chip is woken up,
it will pull down the CTS line. If without this workaround patch, the
UART TX pin cannot send the break signal successfully as it affected by
the BT CTS pin. After adding this patch, the BT power save feature can
work well.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221214031137.28815-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LPUART Status Register needs to be cleared when closing the uart
port to get a clean environment when reopening the uart.
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221125101953.18753-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UARTBAUD_RDMAE and UARTBAUD_TDMAE are enabled in lpuart32_startup(), but
lpuart32_shutdown() not disable them, only free the dma ring buffer and
release the dma channels, so here disable the Rx/Tx DMA first in
lpuart32_shutdown().
Fixes: 42b68768e5 ("serial: fsl_lpuart: DMA support for 32-bit variant")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221125101953.18753-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the lpuart driver, the Idle Line Interrupt Enable now is only needed
for the CPU mode, so enable the UARTCTRL_ILIE at the correct place, and
clear it when shutdown.
Also need to configure the suitable UARTCTRL_IDLECFG, now the value is
0x7, represent 128 idle characters will trigger the Idle Line Interrupt.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221125101953.18753-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use magic literals & comments but define a real field instead
for UART_IIR_FIFO_ENABLED and name also the values.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221125130509.8482-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add UART_MSR_STATUS_BITS for CD, RI, DSR & CTS. Use names for the
literal.
Don't make the define for combined flags part of UAPI.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221125130509.8482-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of literal 0x0f, add a define for enabling all IER bits the
8250 driver is interested in.
Don't make the define for combined flags part of UAPI.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221125130509.8482-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Karol Gugala <kgugala@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Cc: Gabriel Somlo <gsomlo@gmail.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20221125142756.3e51a28d@endymion.delvare
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The polling liteuart_putchar() function is only called from methods
conditionally enabled by CONFIG_SERIAL_LITEUART_CONSOLE. Move its
definition closer to the console code where it is dependent on the
same config option.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-15-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch the TX path to IRQ-driven operation, while maintaining support
for polling mode via the poll timer.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-14-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for IRQ-driven RX. Support for the TX path will be added
in a separate commit.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-13-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move definitions for liteuart_[stop|start]_tx(), liteuart_stop_rx(),
and liteuart_putchar() to a more convenient location in preparation
for adding IRQ support. This patch contains no functional changes.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-12-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the rx loop into its own dedicated function, and (for now)
call it from the poll timer. This is in preparation for adding irq
support to the receive path.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-11-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `status` variable will always be `1` when passed into the call
to `uart_insert_char()`, so it can be eliminated altogether.
Use `u8` as the type for `ch`, as it matches the return type of
the `litex_read8()` call which produces its value.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-10-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simply provide the hard-coded TTY_NORMAL flag to uart_insert_char()
directly -- no need to dedicate a variable for that exclusive purpose.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-9-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While receiving characters, it is necessary to acknowledge each one
by writing to the EV_PENDING register's EV_RX bit. Ensure we do not
also gratuitously set the EV_TX bit in the process.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-8-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling tty_flip_buffer_push() for each individual received character
is overkill. Move it out of the rx loop, and only call it once per
set of characters received together.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-7-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove regshift and iobase port fields, since they are unused
by the driver.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-5-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove stub uart_ops methods that are not called unconditionally
from serial_core.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-4-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that earlycon semihost driver works on RISC-V too, let's use a
much more generic name for the driver.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Tested-by: Sergey Matyukevich <sergey.matyukevich@syntacore.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Link: https://lore.kernel.org/r/20221209150437.795918-4-bmeng@tinylab.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms, namely AMD Picasso, use non standard uart clocks (48M),
witch makes it impossible to use with earlycon.
Let the user select its own frequency.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123-serial-clk-v3-1-49c516980ae0@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting an interrupt with IRQF_ONESHOT will run the primary handler
in the hard-IRQ context even in the force-threaded mode. The
force-threaded mode is used by PREEMPT_RT in order to avoid acquiring
sleeping locks (spinlock_t) in hard-IRQ context. This combination
makes it impossible and leads to "sleeping while atomic" warnings.
Use one interrupt handler for both handlers (primary and secondary)
and drop the IRQF_ONESHOT flag which is not needed.
Fixes: e359b4411c ("serial: stm32: fix threaded interrupt handling")
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Valentin Caron <valentin.caron@foss.st.com> # V3
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230112180417.25595-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In RS485 mode the transmission of a high priority character fails since it
is written to the data register before the transmitter is enabled. Fix this
in pl011_tx_chars() by enabling RS485 transmission before writing the
character.
Fixes: 8d47923772 ("serial: amba-pl011: add RS485 support")
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20230108181735.10937-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A local variable sg is used to store scatterlist pointer in
pch_dma_tx_complete(). The for loop doing Tx byte accounting before
dma_unmap_sg() alters sg in its increment statement. Therefore, the
pointer passed into dma_unmap_sg() won't match to the one given to
dma_map_sg().
To fix the problem, use priv->sg_tx_p directly in dma_unmap_sg()
instead of the local variable.
Fixes: da3564ee02 ("pch_uart: add multi-scatter processing")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230103093435.4396-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver's probe allocates memory for RX FIFO (port->rx_fifo) based on
default RX FIFO depth, e.g. 16. Later during serial startup the
qcom_geni_serial_port_setup() updates the RX FIFO depth
(port->rx_fifo_depth) to match real device capabilities, e.g. to 32.
The RX UART handle code will read "port->rx_fifo_depth" number of words
into "port->rx_fifo" buffer, thus exceeding the bounds. This can be
observed in certain configurations with Qualcomm Bluetooth HCI UART
device and KASAN:
Bluetooth: hci0: QCA Product ID :0x00000010
Bluetooth: hci0: QCA SOC Version :0x400a0200
Bluetooth: hci0: QCA ROM Version :0x00000200
Bluetooth: hci0: QCA Patch Version:0x00000d2b
Bluetooth: hci0: QCA controller version 0x02000200
Bluetooth: hci0: QCA Downloading qca/htbtfw20.tlv
bluetooth hci0: Direct firmware load for qca/htbtfw20.tlv failed with error -2
Bluetooth: hci0: QCA Failed to request file: qca/htbtfw20.tlv (-2)
Bluetooth: hci0: QCA Failed to download patch (-2)
==================================================================
BUG: KASAN: slab-out-of-bounds in handle_rx_uart+0xa8/0x18c
Write of size 4 at addr ffff279347d578c0 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.1.0-rt5-00350-gb2450b7e00be-dirty #26
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
dump_backtrace.part.0+0xe0/0xf0
show_stack+0x18/0x40
dump_stack_lvl+0x8c/0xb8
print_report+0x188/0x488
kasan_report+0xb4/0x100
__asan_store4+0x80/0xa4
handle_rx_uart+0xa8/0x18c
qcom_geni_serial_handle_rx+0x84/0x9c
qcom_geni_serial_isr+0x24c/0x760
__handle_irq_event_percpu+0x108/0x500
handle_irq_event+0x6c/0x110
handle_fasteoi_irq+0x138/0x2cc
generic_handle_domain_irq+0x48/0x64
If the RX FIFO depth changes after probe, be sure to resize the buffer.
Fixes: f9d690b6ec ("tty: serial: qcom_geni_serial: Allocate port->rx_fifo buffer in probe")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221221164022.1087814-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A remove callback just returning 0 is equivalent to no remove callback
at all. So drop the useless function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221212212037.3773636-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several mutexes are taken while setting up console serial ports. In
particular, the tty_port->mutex and @console_mutex are taken:
serial_pnp_probe
serial8250_register_8250_port
uart_add_one_port (locks tty_port->mutex)
uart_configure_port
register_console (locks @console_mutex)
In order to synchronize kgdb's tty_find_polling_driver() with
register_console(), commit 6193bc9084 ("tty: serial: kgdboc:
synchronize tty_find_polling_driver() and register_console()") takes
the @console_mutex. However, this leads to the following call chain
(with locking):
platform_probe
kgdboc_probe
configure_kgdboc (locks @console_mutex)
tty_find_polling_driver
uart_poll_init (locks tty_port->mutex)
uart_set_options
This is clearly deadlock potential due to the reverse lock ordering.
Since uart_set_options() requires holding @console_mutex in order to
serialize early initialization of the serial-console lock, take the
@console_mutex in uart_poll_init() instead of configure_kgdboc().
Since configure_kgdboc() was using @console_mutex for safe traversal
of the console list, change it to use the SRCU iterator instead.
Add comments to uart_set_options() kerneldoc mentioning that it
requires holding @console_mutex (aka the console_list_lock).
Fixes: 6193bc9084 ("tty: serial: kgdboc: synchronize tty_find_polling_driver() and register_console()")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
[pmladek@suse.com: Export console_srcu_read_lock_is_held() to fix build kgdboc as a module.]
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20230112161213.1434854-1-john.ogness@linutronix.de
A number of device drivers reference CONFIG_ARM_S3C24XX_CPUFREQ or
similar symbols that are no longer available with the platform gone,
though the drivers themselves are still used on newer platforms,
so remove these hacks.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here is the "big" set of tty/serial driver changes for 6.2-rc1.
As in previous kernel releases, nothing big here at all, just some small
incremental serial/tty layer cleanups and some individual driver
additions and fixes. Highlights are:
- serial helper macros from Jiri Slaby to reduce the amount of
duplicated code in serial drivers
- api cleanups and consolidations from Ilpo Järvinen in lots of serial
drivers
- the usual set of n_gsm fixes from Daniel Starke as that code gets
exercised more
- TIOCSTI is finally able to be disabled if requested (security
hardening feature from Kees Cook)
- fsl_lpuart driver fixes and features added
- other small serial driver additions and fixes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wt5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynSiACffLCC9SFnP1ClJJh73OpCN11alDAAoIfMct2A
/zrJ4on7o0YQU1Ilg2+k
=eD/I
-----END PGP SIGNATURE-----
Merge tag 'tty-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver changes for 6.2-rc1.
As in previous kernel releases, nothing big here at all, just some
small incremental serial/tty layer cleanups and some individual driver
additions and fixes. Highlights are:
- serial helper macros from Jiri Slaby to reduce the amount of
duplicated code in serial drivers
- api cleanups and consolidations from Ilpo Järvinen in lots of
serial drivers
- the usual set of n_gsm fixes from Daniel Starke as that code gets
exercised more
- TIOCSTI is finally able to be disabled if requested (security
hardening feature from Kees Cook)
- fsl_lpuart driver fixes and features added
- other small serial driver additions and fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (97 commits)
serial: atmel: don't stop the transmitter when doing PIO
serial: atmel: cleanup atmel_start+stop_tx()
tty: serial: fsl_lpuart: switch to new dmaengine_terminate_* API
serial: sunsab: Fix error handling in sunsab_init()
serial: altera_uart: fix locking in polling mode
serial: pch: Fix PCI device refcount leak in pch_request_dma()
tty: serial: fsl_lpuart: Use pm_ptr() to avoid need to make pm __maybe_unused
tty: serial: fsl_lpuart: Add runtime pm support
tty: serial: fsl_lpuart: enable wakeup source for lpuart
serdev: Replace poll loop by readx_poll_timeout() macro
tty: synclink_gt: unwind actions in error path of net device open
serial: stm32: move dma_request_chan() before clk_prepare_enable()
dt-bindings: serial: xlnx,opb-uartlite: Drop 'contains' from 'xlnx,use-parity'
serial: pl011: Do not clear RX FIFO & RX interrupt in unthrottle.
serial: amba-pl011: avoid SBSA UART accessing DMACR register
tty: serial: altera_jtaguart: remove struct altera_jtaguart
tty: serial: altera_jtaguart: use uart_port::read_status_mask
tty: serial: altera_jtaguart: remove unused altera_jtaguart::sigs
tty: serial: altera_jtaguart: remove flag from altera_jtaguart_rx_chars()
n_tty: Rename tail to old_tail in n_tty_read()
...
-----BEGIN PGP SIGNATURE-----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=1PTZ
-----END PGP SIGNATURE-----
Merge tag 'printk-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Add NMI-safe SRCU reader API. It uses atomic_inc() instead of
this_cpu_inc() on strong load-store architectures.
- Introduce new console_list_lock to synchronize a manipulation of the
list of registered consoles and their flags.
This is a first step in removing the big-kernel-lock-like behavior of
console_lock(). This semaphore still serializes console->write()
calbacks against:
- each other. It primary prevents potential races between early
and proper console drivers using the same device.
- suspend()/resume() callbacks and init() operations in some
drivers.
- various other operations in the tty/vt and framebufer
susbsystems. It is likely that console_lock() serializes even
operations that are not directly conflicting with the
console->write() callbacks here. This is the most complicated
big-kernel-lock aspect of the console_lock() that will be hard
to untangle.
- Introduce new console_srcu lock that is used to safely iterate and
access the registered console drivers under SRCU read lock.
This is a prerequisite for introducing atomic console drivers and
console kthreads. It will reduce the complexity of serialization
against normal consoles and console_lock(). Also it should remove the
risk of deadlock during critical situations, like Oops or panic, when
only atomic consoles are registered.
- Check whether the console is registered instead of enabled on many
locations. It was a historical leftover.
- Cleanly force a preferred console in xenfb code instead of a dirty
hack.
- A lot of code and comment clean ups and improvements.
* tag 'printk-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (47 commits)
printk: htmldocs: add missing description
tty: serial: sh-sci: use setup() callback for early console
printk: relieve console_lock of list synchronization duties
tty: serial: kgdboc: use console_list_lock to trap exit
tty: serial: kgdboc: synchronize tty_find_polling_driver() and register_console()
tty: serial: kgdboc: use console_list_lock for list traversal
tty: serial: kgdboc: use srcu console list iterator
proc: consoles: use console_list_lock for list iteration
tty: tty_io: use console_list_lock for list synchronization
printk, xen: fbfront: create/use safe function for forcing preferred
netconsole: avoid CON_ENABLED misuse to track registration
usb: early: xhci-dbc: use console_is_registered()
tty: serial: xilinx_uartps: use console_is_registered()
tty: serial: samsung_tty: use console_is_registered()
tty: serial: pic32_uart: use console_is_registered()
tty: serial: earlycon: use console_is_registered()
tty: hvc: use console_is_registered()
efi: earlycon: use console_is_registered()
tty: nfcon: use console_is_registered()
serial_core: replace uart_console_enabled() with uart_console_registered()
...
When setting up the early console, the setup() callback of the
regular console is used. It is called manually before registering
the early console instead of providing a setup() callback for the
early console. This is probably because the early setup needs a
different @options during the early stage.
The issue here is that the setup() callback is called without the
console_list_lock held and functions such as uart_set_options()
expect that.
Rather than manually calling the setup() function before registering,
provide an early console setup() callback that will use the different
early options. This ensures that the error checking, ordering, and
locking context when setting up the early console are correct.
Since this early console can only be registered via the earlyprintk=
parameter, the @options argument of the setup() callback will always
be NULL. Rather than simply ignoring the argument, add a WARN_ON()
to get our attention in case the setup() callback semantics should
change in the future.
Note that technically the current implementation works because it is
only used in early boot. And since the early console setup is
performed before registering, it cannot race with anything and thus
does not need any locking. However, longterm maintenance is easier
when drivers rely on the subsystem API rather than manually
implementing steps that could cause breakage in the future.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-41-john.ogness@linutronix.de
kgdboc_earlycon_init() uses the console_lock to ensure that no consoles
are unregistered until the kgdboc_earlycon is setup. The console_list_lock
should be used instead because list synchronization responsibility will
be removed from the console_lock in a later change.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-39-john.ogness@linutronix.de
Calling tty_find_polling_driver() can lead to uart_set_options() being
called (via the poll_init() callback of tty_operations) to configure the
uart. But uart_set_options() can also be called by register_console()
(via the setup() callback of console).
Take the console_list_lock to synchronize against register_console() and
also use it for console list traversal. This also ensures the console list
cannot change until the polling console has been chosen.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-38-john.ogness@linutronix.de
configure_kgdboc() uses the console_lock for console list iteration. Use
the console_list_lock instead because list synchronization responsibility
will be removed from the console_lock in a later change.
The SRCU iterator could have been used here, but a later change will
relocate the locking of the console_list_lock to also provide
synchronization against register_console().
Note, the console_lock is still needed to serialize the device()
callback with other console operations.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-37-john.ogness@linutronix.de
Use srcu console list iteration for safe console list traversal.
Note that this is a preparatory change for when console_lock no
longer provides synchronization for the console list.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-36-john.ogness@linutronix.de
It is not reliable to check for CON_ENABLED in order to identify if a
console is registered. Use console_is_registered() instead.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-30-john.ogness@linutronix.de
It is not reliable to check for CON_ENABLED in order to identify if a
console is registered. Use console_is_registered() instead.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-29-john.ogness@linutronix.de
It is not reliable to check for CON_ENABLED in order to identify if a
console is registered. Use console_is_registered() instead.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-28-john.ogness@linutronix.de
It is not reliable to check for CON_ENABLED in order to identify if a
console is registered. Use console_is_registered() instead.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-27-john.ogness@linutronix.de
All users of uart_console_enabled() really want to know if a console
is registered. It is not reliable to check for CON_ENABLED in order
to identify if a console is registered. Use console_is_registered()
instead.
A _locked() variant is provided because uart_set_options() is always
called with the console_list_lock held and must check if a console
is registered in order to synchronize with kgdboc.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-23-john.ogness@linutronix.de
kgdboc_earlycon_init() uses the console_lock to ensure that no consoles
are unregistered until the kgdboc_earlycon is setup. This is necessary
because the trapping of the exit() callback assumes that the exit()
callback is not called before the trap is setup.
Explicitly document this non-typical console_lock usage.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-9-john.ogness@linutronix.de
Unprotected list walks are not necessarily safe.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-2-john.ogness@linutronix.de
Writing ATMEL_US_TXDIS to ATMEL_US_CR makes the transmitter NOT to send
the just queued character. This means when the character is last and
uart calls ops->stop_tx(), the character is not sent at all.
The usart datasheet is not much specific on this, it just says the
transmitter is stopped. But apparently, the character is dropped. So
we should stop the transmitter only for DMA and PDC transfers to not
send any more characters. For PIO, this is unexpected and deviates from
other drivers. In particular, the below referenced commit broke TX as it
added a call to ->stop_tx() after the very last character written to the
transmitter.
So fix this by limiting the write of ATMEL_US_TXDIS to DMA transfers
only.
Even there, I don't know if it is correctly implemented. Are all the
queued characters sent once ->start_tx() is called? Anyone tested flow
control -- be it hard (RTSCTS) or the soft (XOFF/XON) one?
Fixes: 2d141e683e ("tty: serial: use uart_port_tx() helper")
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: linux-arm-kernel@lists.infradead.org
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123082736.24566-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define local variables holding information about whether pdc or dma is
used in the HW. These are retested several times by calls to
atmel_use_pdc_tx() and atmel_use_dma_tx(). So to make the code more
readable, simply cache the values.
This is also a preparatory patch for the next one (where is_pdc is used
once more in atmel_stop_tx()).
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: linux-arm-kernel@lists.infradead.org
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123082736.24566-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221123023619.30173-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunsab_init() returns the platform_driver_register() directly without
checking its return value, if platform_driver_register() failed, the
allocated sunsab_ports is leaked.
Fix by free sunsab_ports and set it to NULL when platform_driver_register()
failed.
Fixes: c4d37215a8 ("[SERIAL] sunsab: Convert to of_driver framework.")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221123061212.52593-1-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since altera_uart_interrupt() may also be called from
a poll timer in "serving_softirq" context, use
spin_[lock_irqsave|unlock_irqrestore] variants, which
are appropriate for both softirq and hardware interrupt
contexts.
Fixes: 2f8b9c15cd ("altera_uart: Add support for polling mode (IRQ-less)")
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20221122200426.888349-1-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As comment of pci_get_slot() says, it returns a pci_device with its
refcount increased. The caller must decrement the reference count by
calling pci_dev_put().
Since 'dma_dev' is only used to filter the channel in filter(), we can
call pci_dev_put() before exiting from pch_request_dma(). Add the
missing pci_dev_put() for the normal and error path.
Fixes: 3c6a483275 ("Serial: EG20T: add PCH_UART driver")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221122114559.27692-1-wangxiongfeng2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use pm_ptr() to remove the need to mark the pm functions as
__maybe_unused when the kernel is built without CONFIG_PM support.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221110113859.8485-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPUART supports both synchronous wakeup and asynchronous wakeup(wakeup
the system when the UART clocks are shut-off), the synchronous wakeup is
configured by UARTCTRL_RIE interrupt, and the asynchronous wakeup is
configured by UARTBAUD_RXEDGIE interrupt.
Add lpuart_uport_is_active() to determine if the uart port needs to get
into the suspend states, also add lpuart_suspend_noirq() and
lpuart_resume_noirq() to enable and disable the wakeup irq bits if the
uart port needs to be set as wakeup source.
When use lpuart with DMA mode, it still needs to switch to the cpu mode
in .suspend() that enable cpu interrupts RIE and RXEDGIE as wakeup
source, after system resume back, needs to setup DMA again, .resume()
will share the HW setup code with .startup(), so abstract the same code
to the api like lpuart32_hw_setup().
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221110113859.8485-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dma_request_chan() returns a PROBE_DEFER error, clk_disable_unprepare()
will be called and USART clock will be disabled. But early console can be
still active on the same USART.
While moving dma_request_chan() before clk_prepare_enable(), the clock
won't be taken in case of a DMA PROBE_DEFER error, and so it doesn't need
to be disabled. Then USART is still clocked for early console.
Fixes: a7770a4bfc ("serial: stm32: defer probe for dma devices")
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20221118170602.1057863-1-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clearing the RX FIFO will cause data loss.
Copy the pl011_enabl_interrupts implementation, and remove the clear
interrupt and FIFO part of the code.
Fixes: 211565b100 ("serial: pl011: UPSTAT_AUTORTS requires .throttle/unthrottle")
Signed-off-by: delisun <delisun@pateo.com.cn>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221110020108.7700-1-delisun@pateo.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083 b901f001 794038a0 8b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
[1] https://developer.arm.com/documentation/den0094/c/?lang=en
[2] https://lists.xenproject.org/archives/html/xen-devel/2022-11/msg00543.html
Fixes: 0dd1e247fd (drivers: PL011: add support for the ARM SBSA generic UART)
Signed-off-by: Jiamei Xie <jiamei.xie@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20221117103237.86856-1-jiamei.xie@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It contains only struct uart_port, so no need for another structure.
Remove it and convert the rest to use struct uart_port directly.
Cc: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20221115071724.5185-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of self-defined struct altera_jtaguart::imr, use preexisting
uart_port::read_status_mask.
Note that imr was ulong. But there is no reason for that, its values are
uints. And readl/writel's are used to read it/write to it.
Cc: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20221115071724.5185-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TTY_NORMAL is the only value it contains, so remove the variable and use
the constant instead.
Cc: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20221115071724.5185-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a number of small tty and serial driver fixes for 6.1-rc6.
They all resolve reported problems:
- kernel doc build problems with the -rc1 serial driver
documentation update
- n_gsm reported problems
- imx serial driver missing callback
- lots of tiny 8250 driver fixes for reported issues.
All of these have been in linux-next for over a week with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY3fJoQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynycACgozhFjiUOjim8J0qUR943mlhTp/kAn0BVsKSk
PD8gi6Wk5SAybCpHxpsD
=Bqke
-----END PGP SIGNATURE-----
Merge tag 'tty-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty and serial driver fixes for 6.1-rc6.
They all resolve reported problems:
- kernel doc build problems with the -rc1 serial driver documentation
update
- n_gsm reported problems
- imx serial driver missing callback
- lots of tiny 8250 driver fixes for reported issues.
All of these have been in linux-next for over a week with no reported
problems"
* tag 'tty-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
docs/driver-api/miscellaneous: Remove kernel-doc of serial_core.c
serial: 8250: Flush DMA Rx on RLSI
serial: 8250_lpss: Use 16B DMA burst with Elkhart Lake
serial: 8250_lpss: Configure DMA also w/o DMA filter
serial: 8250: Fall back to non-DMA Rx if IIR_RDI occurs
tty: n_gsm: fix sleep-in-atomic-context bug in gsm_control_send
Revert "tty: n_gsm: replace kicktimer with delayed_work"
Revert "tty: n_gsm: avoid call of sleeping functions from atomic context"
serial: imx: Add missing .thaw_noirq hook
tty: serial: fsl_lpuart: don't break the on-going transfer when global reset
serial: 8250: omap: Flush PM QOS work on remove
serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove()
serial: 8250_omap: remove wait loop from Errata i202 workaround
serial: 8250: omap: Fix missing PM runtime calls for omap8250_set_mctrl()
serial: 8250: 8250_omap: Avoid RS485 RTS glitch on ->set_termios()
Returning true from handle_rx_dma() without flushing DMA first creates
a data ordering hazard. If DMA Rx has handled any character at the
point when RLSI occurs, the non-DMA path handles any pending characters
jumping them ahead of those characters that are pending under DMA.
Fixes: 75df022b5f ("serial: 8250_dma: Fix RX handling")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configure DMA to use 16B burst size with Elkhart Lake. This makes the
bus use more efficient and works around an issue which occurs with the
previously used 1B.
The fix was initially developed by Srikanth Thokala and Aman Kumar.
This together with the previous config change is the cleaned up version
of the original fix.
Fixes: 0a9410b981 ("serial: 8250_lpss: Enable DMA on Intel Elkhart Lake")
Cc: <stable@vger.kernel.org> # serial: 8250_lpss: Configure DMA also w/o DMA filter
Reported-by: Wentong Wu <wentong.wu@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the platform doesn't use DMA device filter (as is the case with
Elkhart Lake), whole lpss8250_dma_setup() setup is skipped. This
results in skipping also *_maxburst setup which is undesirable.
Refactor lpss8250_dma_setup() to configure DMA even if filter is not
setup.
Cc: stable <stable@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DW UART sometimes triggers IIR_RDI during DMA Rx when IIR_RX_TIMEOUT
should have been triggered instead. Since IIR_RDI has higher priority
than IIR_RX_TIMEOUT, this causes the Rx to hang into interrupt loop.
The problem seems to occur at least with some combinations of
small-sized transfers (I've reproduced the problem on Elkhart Lake PSE
UARTs).
If there's already an on-going Rx DMA and IIR_RDI triggers, fall
graciously back to non-DMA Rx. That is, behave as if IIR_RX_TIMEOUT had
occurred.
8250_omap already considers IIR_RDI similar to this change so its
nothing unheard of.
Fixes: 75df022b5f ("serial: 8250_dma: Fix RX handling")
Cc: <stable@vger.kernel.org>
Co-developed-by: Srikanth Thokala <srikanth.thokala@intel.com>
Signed-off-by: Srikanth Thokala <srikanth.thokala@intel.com>
Co-developed-by: Aman Kumar <aman.kumar@intel.com>
Signed-off-by: Aman Kumar <aman.kumar@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 801954d121 ("serial: 8250: 8250_omap: Support native RS485")
calculates RS485 delays from the baudrate. The baudrate is generated
with either a 16x or 13x divisor. The divisor is set in the Mode
Definition Register 1 (MDR1).
The commit erroneously assumes that the register stores the divisor as
a bitmask and uses a logical AND to differentiate between 16x and 13x
divisors. However the divisor is really stored as a 3-bit mode
(see lines 363ff in include/uapi/linux/serial_reg.h).
The logical AND operation is performed with UART_OMAP_MDR1_16X_MODE,
which is defined as 0x0 and hence yields false. So the commit always
assumes a 13x divisor. Fix by using an equal comparison. This works
because we never set any of the other 5 bits in the register. (They
pertain to IrDA mode, which is not supported by the driver).
Fixes: 801954d121 ("serial: 8250: 8250_omap: Support native RS485")
Link: https://lore.kernel.org/linux-serial/202211070440.8hWunFUN-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/7d5b04da13d89b8708b9543a0b125f2b6062a77b.1667977259.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A problem about 8250_bcm7271 create debugfs failed is triggered with the
following log given:
[ 324.516635] debugfs: Directory 'bcm7271-uart' with parent '/' already present!
The reason is that brcmuart_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of 8250_bcm7271 can never be created later.
brcmuart_init()
debugfs_create_dir() # create debugfs directory
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when platform_driver_register() returns error.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221109072110.117291-2-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA Rx completes, the current behavior is to just exit the DMA
completion handler without future actions. If the transfer is still
on-going, UART will trigger an interrupt and that eventually rearms the
DMA Rx. The extra interrupt round-trip has an inherent latency cost
that increases the risk of FIFO overrun. In such situations, the
latency margin tends to already be less due to FIFO not being empty.
Add check into DMA Rx completion handler to detect if LSR has DR (Data
Ready) still set. DR indicates there will be more characters pending
and DMA Rx can be rearmed right away to handle them.
Cc: Gilles BULOZ <gilles.buloz@kontron.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221107102126.56481-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the two instances of this typo present in the MSM and VT8500 serial
drivers.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20221104103719.2234098-1-j.neuschaefer@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lpuart_global_reset() shouldn't break the on-going transmit engine, need
to recover the on-going data transfer after reset.
This can help earlycon here, since commit 60f361722a ("serial:
fsl_lpuart: Reset prior to registration") moved lpuart_global_reset()
before uart_add_one_port(), earlycon is writing during global reset,
as global reset will disable the TX and clear the baud rate register,
which caused the earlycon cannot work any more after reset, needs to
restore the baud rate and re-enable the transmitter to recover the
earlycon write.
Also move the lpuart_global_reset() down, then we can reuse the
lpuart32_tx_empty() without declaration.
Fixes: bd5305dcab ("tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221024085844.22786-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use str_enabled_disabled() helper instead of open coding the same.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221017171633.65275-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default polarity of RS485 DE signal is active high. This driver does
not handle such case properly. Currently, when a pin is multiplexed as a
UART CTS_B on boot, this pin is pulled HIGH by the i.MX UART CTS circuit,
which activates DE signal on the RS485 transceiver and thus behave as if
the RS485 was transmitting data, so the system blocks the RS485 bus when
it starts and until user application takes over. This behavior is not OK.
The problem consists of two separate parts.
First, the i.MX UART IP requires UCR1 UARTEN and UCR2 RXEN to be set for
UCR2 CTSC and CTS bits to have any effect. The UCR2 CTSC bit permits the
driver to set CTS (RTS_B or RS485 DE signal) to either level sychronous
to the internal UART IP clock. Compared to other options, like GPIO CTS
control, this has the benefit of being synchronous to the UART IP clock
and thus without glitches or bus delays. The reason for the CTS design
is likely because when the Receiver is disabled, the UART IP can never
indicate that it is ready to receive data by assering CTS signal, so
the CTS is always pulled HIGH by default.
When the port is closed by user space, imx_uart_stop_rx() clears UCR2
RXEN bit, and imx_uart_shutdown() clears UCR1 UARTEN bit. This disables
UART Receiver and UART itself, and forces CTS signal HIGH, which leads
to the RS485 bus being blocked because RS485 DE is incorrectly active.
The proposed solution for this problem is to keep the Receiver running
even after the port is closed, but in loopback mode. This disconnects
the RX FIFO input from the RXD external signal, and since UCR2 TXEN is
cleared, the UART Transmitter is disabled, so nothing can feed data in
the RX FIFO. Because the Receiver is still enabled, the UCR2 CTSC and
CTS bits still have effect and the CTS (RS485 DE) control is retained.
Note that in case of RS485 DE signal active low, there is no problem and
no special handling is necessary. The CTS signal defaults to HIGH, thus
the RS485 is by default set to Receive and the bus is not blocked.
Note that while there is the possibility to control CTS using GPIO with
either CTS polarity, this has the downside of not being synchronous to
the UART IP clock and thus glitchy and susceptible to slow DE switching.
Second, on boot, before the UART driver probe callback is called, the
driver core triggers pinctrl_init_done() and configures the IOMUXC to
default state. At this point, UCR1 UARTEN and UCR2 RXEN are both still
cleared, but UART CTS_B (RS485 DE) is configured as CTS function, thus
the RTS signal is pulled HIGH by the UART IP CTS circuit.
One part of the solution here is to enable UCR1 UARTEN and UCR2 RXEN and
UTS loopback in this driver probe callback, thus unblocking the CTSC and
CTS control early on. But this is still too late, since the pin control
is already configured and CTS has been pulled HIGH for a short period
of time.
When Linux kernel boots and this driver is bound, the pin control is set
to special "init" state if the state is available, and driver can switch
the "default" state afterward when ready. This state can be used to set
the CTS line as a GPIO in DT temporarily, and a GPIO hog can force such
GPIO to LOW, thus keeping the RS485 DE line LOW early on boot. Once the
driver takes over and UCR1 UARTEN and UCR2 RXEN and UTS loopback are all
enabled, the driver can switch to "default" pin control state and control
the CTS line as function instead. DT binding example is below:
"
&gpio6 {
rts-init-hog {
gpio-hog;
gpios = <5 0>;
output-low;
line-name = "rs485-de";
};
};
&uart5 { /* DHCOM UART2 */
pinctrl-0 = <&pinctrl_uart5>;
pinctrl-1 = <&pinctrl_uart5_init>;
pinctrl-names = "default", "init";
...
};
pinctrl_uart5_init: uart5-init-grp {
fsl,pins = <
...
MX6QDL_PAD_CSI0_DAT19__GPIO6_IO05 0x30b1
>;
};
pinctrl_uart5: uart5-grp {
fsl,pins = <
...
MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B 0x30b1
>;
};
"
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220929144400.13571-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rebinding 8250_omap in a loop will at some point produce a warning for
kernel/power/qos.c:296 cpu_latency_qos_update_request() with error
"cpu_latency_qos_update_request called for unknown object". Let's flush
the possibly pending PM QOS work scheduled from omap8250_runtime_suspend()
before we disable runtime PM.
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221028110044.54719-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On remove, we get an error for "Runtime PM usage count underflow!". I guess
this driver is mostly built-in, and this issue has gone unnoticed for a
while. Somehow I did not catch this issue with my earlier fix done with
commit 4e0f5cc650 ("serial: 8250_omap: Fix probe and remove for PM
runtime").
Fixes: 4e0f5cc650 ("serial: 8250_omap: Fix probe and remove for PM runtime")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Depends-on: dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
Link: https://lore.kernel.org/r/20221028105813.54290-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were occasionally seeing the "Errata i202: timedout" on an AM335x
board when repeatedly opening and closing a UART connected to an active
sender. As new input may arrive at any time, it is possible to miss the
"RX FIFO empty" condition, forcing the loop to wait until it times out.
Nothing in the i202 Advisory states that such a wait is even necessary;
other FIFO clear functions like serial8250_clear_fifos() do not wait
either. For this reason, it seems safe to remove the wait, fixing the
mentioned issue.
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20221013112339.2540767-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are cases where omap8250_set_mctrl() may get called after the
UART has already autoidled causing an asynchronous external abort.
This can happen on ttyport_open():
mem_serial_in from omap8250_set_mctrl+0x38/0xa0
omap8250_set_mctrl from uart_update_mctrl+0x4c/0x58
uart_update_mctrl from uart_dtr_rts+0x60/0xa8
uart_dtr_rts from tty_port_block_til_ready+0xd0/0x2a8
tty_port_block_til_ready from uart_open+0x14/0x1c
uart_open from ttyport_open+0x64/0x148
And on ttyport_close():
omap8250_set_mctrl from uart_update_mctrl+0x3c/0x48
uart_update_mctrl from uart_dtr_rts+0x54/0x9c
uart_dtr_rts from tty_port_shutdown+0x78/0x9c
tty_port_shutdown from tty_port_close+0x3c/0x74
tty_port_close from ttyport_close+0x40/0x58
It can also happen on disassociate_ctty() calling uart_shutdown()
that ends up calling omap8250_set_mctrl().
Let's fix the issue by adding missing PM runtime calls to
omap8250_set_mctrl(). To do this, we need to add __omap8250_set_mctrl()
that can be called from both omap8250_set_mctrl(), and from runtime PM
resume path when restoring the registers.
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Reported-by: Romain Naour <romain.naour@smile.fr>
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Depends-on: dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
Link: https://lore.kernel.org/r/20221024063613.25943-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RS485-enabled UART ports on TI Sitara SoCs with active-low polarity
exhibit a Transmit Enable glitch on ->set_termios():
omap8250_restore_regs(), which is called from omap_8250_set_termios(),
sets the TCRTLR bit in the MCR register and clears all other bits,
including RTS. If RTS uses active-low polarity, it is now asserted
for no reason.
The TCRTLR bit is subsequently cleared by writing up->mcr to the MCR
register. That variable is always zero, so the RTS bit is still cleared
(incorrectly so if RTS is active-high).
(up->mcr is not, as one might think, a cache of the MCR register's
current value. Rather, it only caches a single bit of that register,
the AFE bit. And it only does so if the UART supports the AFE bit,
which OMAP does not. For details see serial8250_do_set_termios() and
serial8250_do_set_mctrl().)
Finally at the end of omap8250_restore_regs(), the MCR register is
restored (and RTS deasserted) by a call to up->port.ops->set_mctrl()
(which equals serial8250_set_mctrl()) and serial8250_em485_stop_tx().
So there's an RTS glitch between setting TCRTLR and calling
serial8250_em485_stop_tx(). Avoid by using a read-modify-write
when setting TCRTLR.
While at it, drop a redundant initialization of up->mcr. As explained
above, the variable isn't used by the driver and it is already
initialized to zero because it is part of the static struct
serial8250_ports[] declared in 8250_core.c. (Static structs are
initialized to zero per section 6.7.8 nr. 10 of the C99 standard.)
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/6554b0241a2c7fd50f32576fdbafed96709e11e8.1664278942.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
JZ4750/55/60 (but not JZ4760b) have an optional /2 divider between the
EXT oscillator and some peripherals including UART, which will
be enabled if using a 24 MHz oscillator, and disabled when
using a 12 MHz oscillator.
This behavior relies on hardware differences: most boards (if not all)
with those SoCs have 12 or 24 MHz oscillators but many peripherals want
12Mhz to operate properly (AIC and USB-PHY at least).
The 16MHz threshold looks arbitrary but used in vendor's bootloader code
for enable the divider.
The patch doesn't affect JZ4760's behavior as it is subject for another
patchset with re-classification of all supported ingenic UARTs.
Link: https://github.com/carlos-wong/uboot_jz4755/blob/master/cpu/mips/jz_serial.c#L158
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221031184041.1338129-3-lis8215@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Read the DMA status before terminating the DMA, as doing so deletes
the DMA desc.
Also, to get the correct transfer status information, pause the DMA
using dmaengine_pause() before reading the DMA status.
Fixes: e9ea096dd2 ("serial: tegra: add serial driver")
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Signed-off-by: Kartik <kkartik@nvidia.com>
Link: https://lore.kernel.org/r/1666105086-17326-1-git-send-email-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-34-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-29-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-23-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-22-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-18-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-By: Richard GENOUD <richard.genoud@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-12-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take advantage of the new uart_xmit_advance() helper.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent TI Sitara SoCs such as AM64/AM65 have gained the ability to
automatically assert RTS when data is transmitted, obviating the need
to emulate this functionality in software.
The feature is controlled through new DIR_EN and DIR_POL bits in the
Mode Definition Register 3. For details see page 8783 and 8890 of the
AM65 TRM: https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Bin Liu <b-liu@ti.com>
Tested-by: Zeng Chao <chao.zeng@siemens.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/e9f25f5c9200a35d3162973c2b45d6b892cc9bf2.1665906869.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added changes to support the hibernation feature for serial UART.
Added support for freeze, restore and thaw callbacks to put the
device into hibernation.
Signed-off-by: Aniket Randive <quic_arandive@quicinc.com>
Link: https://lore.kernel.org/r/1665123780-20557-1-git-send-email-quic_arandive@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_port_tx_limited() is a new helper to send characters to the device.
Use it in these drivers.
mux.c also needs to define tx_done(). But I'm not sure if the driver
really wants to wait for all the characters to dismiss from the HW fifo
at this code point. Hence I marked this as FIXME.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: linux-riscv@lists.infradead.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221004104927.14361-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the aim of dropping direct selects of drivers from Kconfig.socs,
default the SiFive serial drivers to enabled if SOC_CANAAN.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221005171348.167476-4-conor@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the aim of dropping direct selects of drivers from Kconfig.socs,
default the SiFive serial drivers to the value of SOC_SIFIVE.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221005171348.167476-3-conor@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file name of this driver is misleading - it handles various serial
ports on parisc machines, not just such on the GSC bus.
Rename the file to make this clearer.
Suggested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Although the name of the driver 8250_gsc.c suggests that it handles
only serial ports on the GSC bus, it does handle serial ports listed
in the parisc machine inventory as well, e.g. the serial ports in a
C8000 PCI-only workstation.
Change the dependency to CONFIG_PARISC, so that the driver gets included
in the kernel even if CONFIG_GSC isn't set.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
* Convert the PDC console to an early console
* Unbreak mmap() of graphics card memory due to PAGE_SPECIAL pgtable flag
* Reduce the size of the alternative tables
* Align stifb graphics card memory size to 4MB
* Spelling fixes
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCY0mnYAAKCRD3ErUQojoP
X1z3AQC204Pq725WM3rgEomIqFjk8QaU2UFcNQ74a52V3AUiiQD8C0DFmWDbssUv
ZE5uC+ySlNd1hLkL3QYxrbbwuL+y+Q0=
=YvFZ
-----END PGP SIGNATURE-----
Merge tag 'parisc-for-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"Fixes:
- When we added basic vDSO support in kernel 5.18 we introduced a bug
which prevented a mmap() of graphic card memory. This is because we
used the DMB (data memory break trap bit) page flag as special-bit,
but missed to clear that bit when loading the TLB.
- Graphics card memory size was not correctly aligned
- Spelling fixes (from Colin Ian King)
Enhancements:
- PDC console (which uses firmware calls) now rewritten as early
console
- Reduced size of alternative tables"
* tag 'parisc-for-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix spelling mistake "mis-match" -> "mismatch" in eisa driver
parisc: Fix userspace graphics card breakage due to pgtable special bit
parisc: fbdev/stifb: Align graphics memory size to 4MB
parisc: Convert PDC console to an early console
parisc: Reduce kernel size by packing alternative tables
Rewrite the PDC console to become an early console.
Beside the fact that now boot information is visible until another
(text- or graphics) console takes over, this benefits as well machines
with a yet-unsupported STI console and kgdb.
Signed-off-by: Helge Deller <deller@gmx.de>
Here is the big set of TTY and Serial driver updates for 6.1-rc1.
Lots of cleanups in here, no real new functionality this time around,
with the diffstat being that we removed more lines than we added!
Included in here are:
- termios unification cleanups from Al Viro, it's nice to
finally get this work done
- tty serial transmit cleanups in various drivers in preparation
for more cleanup and unification in future releases (that work
was not ready for this release.)
- n_gsm fixes and updates
- ktermios cleanups and code reductions
- dt bindings json conversions and updates for new devices
- some serial driver updates for new devices
- lots of other tiny cleanups and janitorial stuff. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0BSdA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylucQCfaXIrYuh2AHcb6+G+Nqp1xD2BYaEAoIdLyOCA
a2yziLrDF6us2oav6j4x
=Wv+X
-----END PGP SIGNATURE-----
Merge tag 'tty-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of TTY and Serial driver updates for 6.1-rc1.
Lots of cleanups in here, no real new functionality this time around,
with the diffstat being that we removed more lines than we added!
Included in here are:
- termios unification cleanups from Al Viro, it's nice to finally get
this work done
- tty serial transmit cleanups in various drivers in preparation for
more cleanup and unification in future releases (that work was not
ready for this release)
- n_gsm fixes and updates
- ktermios cleanups and code reductions
- dt bindings json conversions and updates for new devices
- some serial driver updates for new devices
- lots of other tiny cleanups and janitorial stuff. Full details in
the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (102 commits)
serial: cpm_uart: Don't request IRQ too early for console port
tty: serial: do unlock on a common path in altera_jtaguart_console_putc()
tty: serial: unify TX space reads under altera_jtaguart_tx_space()
tty: serial: use FIELD_GET() in lqasc_tx_ready()
tty: serial: extend lqasc_tx_ready() to lqasc_console_putchar()
tty: serial: allow pxa.c to be COMPILE_TESTed
serial: stm32: Fix unused-variable warning
tty: serial: atmel: Add COMMON_CLK dependency to SERIAL_ATMEL
serial: 8250: Fix restoring termios speed after suspend
serial: Deassert Transmit Enable on probe in driver-specific way
serial: 8250_dma: Convert to use uart_xmit_advance()
serial: 8250_omap: Convert to use uart_xmit_advance()
MAINTAINERS: Solve warning regarding inexistent atmel-usart binding
serial: stm32: Deassert Transmit Enable on ->rs485_config()
serial: ar933x: Deassert Transmit Enable on ->rs485_config()
tty: serial: atmel: Use FIELD_PREP/FIELD_GET
tty: serial: atmel: Make the driver aware of the existence of GCLK
tty: serial: atmel: Only divide Clock Divisor if the IP is USART
tty: serial: atmel: Separate mode clearing between UART and USART
dt-bindings: serial: atmel,at91-usart: Add gclk as a possible USART clock
...
The main changes this time are for the organization of the Kconfig
files, introducing per-vendor top-level options on arm64 to match
those on arm32, and making the platform selection on arm32 more
uniform, in particular for the remaining StrongARM platforms that
still have a couple of special cases compared to the more recent
ones.
I also did a cleanup of the old Footbridge platform, which was
the last holdout for the phys_to_dma()/dma_to_phys() interface
that is now completely gone from arm32, completing work started
by Christoph Hellwig.
-----BEGIN PGP SIGNATURE-----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=xsKV
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"The main changes this time are for the organization of the Kconfig
files, introducing per-vendor top-level options on arm64 to match
those on arm32, and making the platform selection on arm32 more
uniform, in particular for the remaining StrongARM platforms that
still have a couple of special cases compared to the more recent ones.
I also did a cleanup of the old Footbridge platform, which was the
last holdout for the phys_to_dma()/dma_to_phys() interface that is now
completely gone from arm32, completing work started by Christoph
Hellwig"
* tag 'arm-soc-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
ARM: aspeed: Kconfig: Fix indentation
ARM: Drop CMDLINE_* dependency on ATAGS
ARM: Drop CMDLINE_FORCE dependency on !ARCH_MULTIPLATFORM
ARM: s3c: remove orphan declarations from arch/arm/mach-s3c/devs.h
pxa: Drop if with an always false condition
ARM: orion: fix include path
ARM: shmobile: Drop selecting SOC_BUS
arm64: renesas: Drop selecting SOC_BUS
ARM: disallow PCI with MMU=n again
ARM: footbridge: remove custom DMA address handling
MAINTAINERS: Add BCM4908 maintainer to BCMBCA entry
ARM: footbridge: move isa-dma support into footbridge
ARM: footbridge: remove leftover from personal-server
ARM: footbridge: remove addin mode
arm64: Kconfig.platforms: Group NXP platforms together
arm64: Kconfig.platforms: Re-organized Broadcom menu
ARM: make ARCH_MULTIPLATFORM user-visible
ARM: fix XIP_KERNEL dependencies
ARM: Kconfig: clean up platform selection
ARM: simplify machdirs/platdirs handling
...
The drivers branch for 6.1 is a bit larger than for most releases. Most
of the changes come from SoC maintainers for the drivers/soc subsystem:
- A new driver for error handling on the NVIDIA Tegra
'control backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip
SoCs, various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM
driver, the Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas,
Tegra, Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers that
merge updates this way:
- Various updates and new drivers in the memory controller
subsystem for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A
v1.1 specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem
-----BEGIN PGP SIGNATURE-----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=WX9J
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"The drivers branch for 6.1 is a bit larger than for most releases.
Most of the changes come from SoC maintainers for the drivers/soc
subsystem:
- A new driver for error handling on the NVIDIA Tegra 'control
backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip SoCs,
various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM driver, the
Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas, Tegra,
Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers
that merge updates this way:
- Various updates and new drivers in the memory controller subsystem
for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A v1.1
specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem"
* tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (149 commits)
ARM: remove check for CONFIG_DEBUG_LL_SER3
firmware/psci: Add debugfs support to ease debugging
firmware/psci: Print a warning if PSCI doesn't accept PC mode
dt-bindings: memory: snps,dw-umctl2-ddrc: Extend schema with IRQs/resets/clocks props
dt-bindings: memory: snps,dw-umctl2-ddrc: Replace opencoded numbers with macros
dt-bindings: memory: snps,dw-umctl2-ddrc: Use more descriptive device name
dt-bindings: memory: synopsys,ddrc-ecc: Detach Zynq DDRC controller support
soc: sunxi: sram: Add support for the D1 system control
soc: sunxi: sram: Export the LDO control register
soc: sunxi: sram: Save a pointer to the OF match data
soc: sunxi: sram: Return void from the release function
soc: apple: rtkit: Add apple_rtkit_poll
soc: imx: add i.MX93 media blk ctrl driver
soc: imx: add i.MX93 SRC power domain driver
soc: imx: imx8m-blk-ctrl: Use genpd_xlate_onecell
soc: imx: imx8mp-blk-ctrl: handle PCIe PHY resets
soc: imx: imx8m-blk-ctrl: add i.MX8MP VPU blk ctrl
soc: imx: add i.MX8MP HDMI blk ctrl HDCP/HRV_MWR
soc: imx: add icc paths for i.MX8MP hsio/hdmi blk ctrl
soc: imx: add icc paths for i.MX8MP media blk ctrl
...
The following message is seen during boot and the activation of
console port gets delayed until normal serial ports activation.
[ 0.001346] irq: no irq domain found for pic@930 !
The console port doesn't need irq, perform irq reservation later,
during cpm_uart probe.
While at it, don't use NO_IRQ but 0 which is the value returned
by irq_of_parse_and_map() in case of error. By chance powerpc's
NO_IRQ has value 0 but on some architectures it is -1.
Fixes: 14d893fc68 ("powerpc/8xx: Convert CPM1 interrupt controller to platform_device")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/8bed0f30c2e9ef16ae64fb1243a16d54a48eb8da.1664526717.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
port->lock is unlocked in each branch in altera_jtaguart_console_putc(),
so do it before the "if". "status" needs not be under the lock, as the
register was already read.
Cc: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20220927111819.18516-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TX space reads from the control register are performed in various forms
on 4 places in altera_jtaguart. Unify all those and do the read and
masking on a single place.
The new helper altera_jtaguart_tx_space() uses FIELD_GET(), so we can
drop ALTERA_JTAGUART_CONTROL_WSPACE_OFF now.
Cc: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20220927111819.18516-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FIELD_GET() can do the job smarter and more readable. We don't even need
ASCFSTAT_TXFREEOFF. So switch to the former and remove the latter.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220927111819.18516-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is one more place where lqasc_tx_ready() can be used now:
lqasc_console_putchar(). So replace the open-coded variant by the
helper.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220927111819.18516-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no issue compiling pxa.c even in the SERIAL_8250=y case. So to
cover it in the usual configurations, add "|| COMPILE_TEST" there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220927110528.12815-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_SERIAL_EARLYCON and CONFIG_OF are both not set,
gcc warns about unused variable:
drivers/tty/serial/stm32-usart.c:83:32: error: ‘stm32h7_info’ defined but not used [-Werror=unused-variable]
static struct stm32_usart_info stm32h7_info = {
^~~~~~~~~~~~
drivers/tty/serial/stm32-usart.c:61:32: error: ‘stm32f7_info’ defined but not used [-Werror=unused-variable]
static struct stm32_usart_info stm32f7_info = {
^~~~~~~~~~~~
drivers/tty/serial/stm32-usart.c:40:32: error: ‘stm32f4_info’ defined but not used [-Werror=unused-variable]
static struct stm32_usart_info stm32f4_info = {
^~~~~~~~~~~~
cc1: all warnings being treated as errors
Mark these variables as __maybe_unused to fix this.
Fixes: c7039ce904 ("serial: stm32: make info structs static to avoid sparse warnings")
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Link: https://lore.kernel.org/r/20220926025826.44145-1-renzhijie2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver makes use of `__clk_is_enabled()` in order to
know whether a `clk_disable_unprepare()` is needed or not on the
GCLK, a new dependency has been introduced: COMMON_CLK. If this
`CONFIG_COMMON_CLK` is not enabled, whatever config may have this
driver enabled without COMMON_CLK then an undefined reference to
`__clk_is_enabled()` will be issued by the linker.
Thus, make sure that, unless `CONFIG_COMMON_CLK` is enabled, this
driver is not compiled.
Fixes: 5e3ce1f261 ("tty: serial: atmel: Make the driver aware of the existence of GCLK")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220926143244.485578-1-sergiu.moga@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit edc6afc549 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Since commit 027b57170b ("serial: core: Fix initializing and restoring
termios speed") termios speed is available also in struct console.
So properly restore also c_ispeed and c_ospeed members after suspend to fix
restoring termios speed which is not represented by Bnnn constant.
Fixes: 4516d50aab ("serial: 8250: Use canary to restart console after suspend")
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220924104324.4035-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a UART port is newly registered, uart_configure_port() seeks to
deassert RS485 Transmit Enable by setting the RTS bit in port->mctrl.
However a number of UART drivers interpret a set RTS bit as *assertion*
instead of deassertion: Affected drivers include those using
serial8250_em485_config() (except 8250_bcm2835aux.c) and some using
mctrl_gpio (e.g. imx.c).
Since the interpretation of the RTS bit is driver-specific, it is not
suitable as a means to centrally deassert Transmit Enable in the serial
core. Instead, the serial core must call on drivers to deassert it in
their driver-specific way. One way to achieve that is to call
->rs485_config(). It implicitly deasserts Transmit Enable.
So amend uart_configure_port() and uart_resume_port() to invoke
uart_rs485_config(). That allows removing calls to uart_rs485_config()
from drivers' ->probe() hooks and declaring the function static.
Skip any invocation of ->set_mctrl() if RS485 is enabled. RS485 has no
hardware flow control, so the modem control lines are irrelevant and
need not be touched. When leaving RS485 mode, reset the modem control
lines to the state stored in port->mctrl. That way, UARTs which are
muxed between RS485 and RS232 transceivers drive the lines correctly
when switched to RS232. (serial8250_do_startup() historically raises
the OUT1 modem signal because otherwise interrupts are not signaled on
ancient PC UARTs, but I believe that no longer applies to modern,
RS485-capable UARTs and is thus safe to be skipped.)
imx.c modifies port->mctrl whenever Transmit Enable is asserted and
deasserted. Stop it from doing that so port->mctrl reflects the RS232
line state.
8250_omap.c deasserts Transmit Enable on ->runtime_resume() by calling
->set_mctrl(). Because that is now a no-op in RS485 mode, amend the
function to call serial8250_em485_stop_tx().
fsl_lpuart.c retrieves and applies the RS485 device tree properties
after registering the UART port. Because applying now happens on
registration in uart_configure_port(), move retrieval of the properties
ahead of uart_add_one_port().
Link: https://lore.kernel.org/all/20220329085050.311408-1-matthias.schiffer@ew.tq-group.com/
Link: https://lore.kernel.org/all/8f538a8903795f22f9acc94a9a31b03c9c4ccacb.camel@ginzinger.com/
Fixes: d3b3404df3 ("serial: Fix incorrect rs485 polarity on uart open")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2de36eba3fbe11278d5002e4e501afe0ceaca039.1663863805.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_xmit_advance() provides a common way on how to advance
the Tx queue. Use it for the sake of unification and robustness.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220909091102.58941-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_xmit_advance() provides a common way on how to advance
the Tx queue. Use it for the sake of unification and robustness.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220909091258.68886-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The STM32 USART can control RS-485 Transmit Enable in hardware. Since
commit 7df5081cbf ("serial: stm32: Add RS485 RTS GPIO control"),
it can alternatively be controlled in software. That was done to allow
RS-485 even if the RTS pin is unavailable because it's pinmuxed to a
different function.
However the commit neglected to deassert Transmit Enable upon invocation
of the ->rs485_config() callback. Fix it.
Avoid forward declarations by moving stm32_usart_tx_empty(),
stm32_usart_rs485_rts_enable() and stm32_usart_rs485_rts_disable()
further up in the driver.
Fixes: 7df5081cbf ("serial: stm32: Add RS485 RTS GPIO control")
Cc: stable@vger.kernel.org # v5.9+
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/6059eab35dba394468335ef640df8b0050fd9dbd.1662886616.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the PWM driver was changed to disable clocks if no PWMs are enabled,
it ended up also disabling the shared parent with the UART, since the
UART doesn't do any clock enablement on its own.
To avoid these surprises, switch to clk_get_enabled().
Fixes: ace41d7564 ("pwm: sifive: Ensure the clk is enabled exactly once per running PWM")
Cc: stable <stable@kernel.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Link: https://lore.kernel.org/r/20220920160017.7315-1-olof@lixom.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_omap uses em485, fill in rs485_supported accordingly. This makes
RS485 work with 8250_omap again, which was broken with the introduction
of the RS485 config sanitization.
Fixes: be2e2cb1d2 ("serial: Sanitize rs485_struct")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220916110955.161099-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit bd5305dcab ("tty: serial: fsl_lpuart: do software reset
for imx7ulp and imx8qxp"), certain i.MX UARTs are reset after they've
already been registered. Register state may thus be clobbered after
user space has begun to open and access the UART.
Avoid by performing the reset prior to registration.
Fixes: bd5305dcab ("tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp")
Cc: stable@vger.kernel.org # v5.15+
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/72fb646c1b0b11c989850c55f52f9ff343d1b2fa.1662884345.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert all open-coded instances of bitfields retrieval/setting
to FIELD_PREP/FIELD_GET where possible.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220922113347.144383-10-sergiu.moga@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, the atmel serial driver did not take into account the
possibility of using the more customizable generic clock as its
baudrate generator. Unless there is a Fractional Part available to
increase accuracy, there is a high chance that we may be able to
generate a baudrate closer to the desired one by using the GCLK as the
clock source. Now, depending on the error rate between
the desired baudrate and the actual baudrate, the serial driver will
fallback on the generic clock. The generic clock must be provided
in the DT node of the serial that may need a more flexible clock source.
Furthermore, define the bit that represents the choice of having GCLK
as a baudrate source clock inside the USCLKS bitmask of the Mode Register
of USART IP's.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Link: https://lore.kernel.org/r/20220922113347.144383-9-sergiu.moga@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the driver only divides the clock divisor if the
IP handled at that point is USART, since UART IP's do not support
implicit peripheral clock division. Instead, in the case of UART,
go with the highest possible clock divisor.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220922113347.144383-8-sergiu.moga@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When clearing the mode of the serial IP inside the atmel_set_termios()
method, make sure that the difference between the bitfields placement
of the UART IP's and USART IP's is taken into account, as some of
them overlap with each other. For example, ATMEL_UA_BRSRCCK overlaps
with ATMEL_US_NBSTOP and ATMEL_US_USCLKS overlaps with ATMEL_UA_FILTER.
Furthermore, add definitions for the Baud Rate Source Clock and the
Filter bitfields of the Mode Register of UART IP's, since they were
missing.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Link: https://lore.kernel.org/r/20220922113347.144383-7-sergiu.moga@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Invoking TIOCVHANGUP on 8250_mid port on Ice Lake-D and then reopening
the port triggers these faults during serial8250_do_startup():
DMAR: DRHD: handling fault status reg 3
DMAR: [DMA Write NO_PASID] Request device [00:1a.0] fault addr 0x0 [fault reason 0x05] PTE Write access is not set
If the IRQ hasn't been set up yet, the UART will have zeroes in its MSI
address/data registers. Disabling the IRQ at the interrupt controller
won't stop the UART from performing a DMA write to the address programmed
in its MSI address register (zero) when it wants to signal an interrupt.
The UARTs (in Ice Lake-D) implement PCI 2.1 style MSI without masking
capability, so there is no way to mask the interrupt at the source PCI
function level, except disabling the MSI capability entirely, but that
would cause it to fall back to INTx# assertion, and the PCI specification
prohibits disabling the MSI capability as a way to mask a function's
interrupt service request.
The MSI address register is zeroed by the hangup as the irq is freed.
The interrupt is signalled during serial8250_do_startup() performing a
THRE test that temporarily toggles THRI in IER. The THRE test currently
occurs before UART's irq (and MSI address) is properly set up.
Refactor serial8250_do_startup() such that irq is set up before the
THRE test. The current irq setup code is intermixed with the timer
setup code. As THRE test must be performed prior to the timer setup,
extract it into own function and call it only after the THRE test.
The ->setup_timer() needs to be part of the struct uart_8250_ops in
order to not create circular dependency between 8250 and 8250_base
modules.
Fixes: 40b36daad0 ("[PATCH] 8250 UART backup timer")
Reported-by: Lennert Buytenhek <buytenh@arista.com>
Tested-by: Lennert Buytenhek <buytenh@arista.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220922070005.2965-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oxford Semiconductor PCIe (Tornado) 950 serial port devices need to
operate in the enhanced mode via the EFR register for the Divide-by-M
N/8 baud rate generator prescaler to be used in their native UART mode.
Otherwise the prescaler is fixed at 1 causing grossly incorrect baud
rates to be programmed.
Accessing the EFR register requires 16550A features to have been probed
for, so request this to happen regardless of SERIAL_8250_16550A_VARIANTS
by setting UPF_FULL_PROBE in port flags.
Fixes: 366f6c955d ("serial: 8250: Add proper clock handling for OxSemi PCIe devices")
Cc: stable@vger.kernel.org # v5.19+
Reported-by: Anders Blomdell <anders.blomdell@control.lth.se>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209210005040.41633@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A SERIAL_8250_16550A_VARIANTS configuration option has been recently
defined that lets one request the 8250 driver not to probe for 16550A
device features so as to reduce the driver's device startup time in
virtual machines.
Some actual hardware devices require these features to have been fully
determined however for their driver to work correctly, so define a flag
to let drivers request full 16550A feature probing on a device-by-device
basis if required regardless of the SERIAL_8250_16550A_VARIANTS option
setting chosen.
Fixes: dc56ecb81a ("serial: 8250: Support disabling mdelay-filled probes of 16550A variants")
Cc: stable@vger.kernel.org # v5.6+
Reported-by: Anders Blomdell <anders.blomdell@control.lth.se>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209202357520.41633@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This non-trivial code is doubled in transmit_chars(), so it deserves its
own function. This will make next patches easier.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220920052049.20507-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mpc52xx_uart_int_rx_chars() returns unsigned int.
mpc52xx_uart_int_tx_chars() returns int.
The both results are binary ORed to the "keepgoing" variable. Unify all
three to bool as the only interesting value is whether we should keep
looping (true/false).
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220920052049.20507-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The condition in __serial_lpc32xx_tx()'s loop is barely readable.
Extract it to a separate function. This will make the cleanup in the
next patches easier too.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220920052049.20507-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The condition in lqasc_tx_chars()'s loop is barely readable. Extract it
to a separate function. This will make the cleanup in the next patches
easier too.
(Put it before lqasc_start_tx(), so that we can use it there later.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220920052049.20507-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both altera_uart_{r,t}x_chars() need only uart_port, not altera_uart. So
pass the former from altera_uart_interrupt() directly.
Apart it maybe saves a dereference, this makes the transition of
altera_uart_tx_chars() easier to follow in the next patch.
Cc: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220920052049.20507-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "stop TX" path in altera_uart_tx_chars() is open-coded, so:
* use uart_circ_empty() to check if the buffer is empty, and
* when true, call altera_uart_stop_tx().
Cc: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220920052049.20507-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make vt8500_tx_empty() more readable by introducing a new local variable
and move the function before handle_tx(). That way we can reuse it in
there too.
Cc: <linux-arm-kernel@lists.infradead.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220920052049.20507-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This error path needs to unwind instead of just returning directly.
Fixes: 03a8482c17 ("drivers: serial: jsm: Enable support for Digi Classic adapters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YyxFh1+lOeZ9WfKO@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial-omap driver requires an rts-gpio for RS-485 to work.
Historically it has allowed enabling RS-485 even if no rts-gpio was
specified in the device tree.
That doesn't make any sense, so disable RS-485 on probe if rts-gpio is
missing and disallow user space from enabling it.
Three NULL pointer checks for up->rts_gpiod can be dropped as a result,
simplifying the driver slightly.
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/f191dcca0d8ea03598c463fc0d3fba8941ff2275.1662888075.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The machine was removed a while ago, and the checks are
now useless.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In suspend/resume routines, icc flags are hardcoded.
Replace the hardcodes with macros available from header.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Link: https://lore.kernel.org/r/1662564702-7253-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UAPI serial_core.h is guaranteed to be included by in-kernel
one (with the same name). Individual drivers do not need to include
it explicitly. Remove it from the driver.
Note, it's a single driver in the entire kernel that does this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220830152313.14650-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever the atmel_rs485_config() driver method would be called,
the USART mode is reset to normal mode before even checking if
RS485 flag is set, thus resulting in losing the previous USART
mode in the case where the checking fails.
Some tools, such as `linux-serial-test`, lead to the driver calling
this method when doing the setup of the serial port: after setting the
port mode (Hardware Flow Control, Normal Mode, RS485 Mode, etc.),
`linux-serial-test` tries to enable/disable RS485 depending on
the commandline arguments that were passed.
Example of how this issue could reveal itself:
When doing a serial communication with Hardware Flow Control through
`linux-serial-test`, the tool would lead to the driver roughly doing
the following:
- set the corresponding bit to 1 (ATMEL_US_USMODE_HWHS bit in the
ATMEL_US_MR register) through the atmel_set_termios() to enable
Hardware Flow Control
- disable RS485 through the atmel_config_rs485() method
Thus, when the latter is called, the mode will be reset and the
previously set bit is unset, leaving USART in normal mode instead of
the expected Hardware Flow Control mode.
This fix ensures that this reset is only done if the checking for
RS485 succeeds and that the previous mode is preserved otherwise.
Fixes: e8faff7330 ("ARM: 6092/1: atmel_serial: support for RS485 communications")
Cc: stable <stable@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Link: https://lore.kernel.org/r/20220824142902.502596-1-sergiu.moga@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the user initializes the uart port, and waits for the transmit
engine to complete in lpuart32_set_termios(), if the UART TX fifo has
dirty data and the UARTMODIR enable the flow control, the TX fifo may
never be empty. So here we should disable the flow control first to make
sure the transmit engin can complete.
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220821101527.10066-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The setting of RS485 RTS polarity is inverse in the current driver.
When the property of 'rs485-rts-active-low' is enabled in the dts node,
the RTS signal should be LOW during sending. Otherwise, if there is no
such a property, the RTS should be HIGH during sending.
Fixes: 03895cf41d ("tty: serial: fsl_lpuart: Add support for RS-485")
Cc: stable <stable@kernel.org>
Signed-off-by: Nicolas Diaz <nicolas.diaz@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20220805144529.604856-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The number of bits can be calculated using tty_get_frame_size(), no
need for the driver to do it on its own.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220830084925.5608-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver features a custom frame length calculation but the result is
never used. Remove it.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220830084925.5608-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The number of bits can be calculated using tty_get_frame_size(), no
need for the driver to do it on its own. Change bits to unsigned and
baud too since we're touching the declarations line anyway (the
respective core functions are typed unsigned).
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220830084925.5608-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The number of bits can be calculated using helpers in core, no need for
the driver to do it on its own.
The mode register is programmed with frame bits minus 1, rearrange the
comments related to that "feature" closer to the actual write.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220830084925.5608-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The number of bits can be calculated using tty_get_frame_size(), no
need for the driver to do it on its own.
Also remove a comment on number of bits that doesn't match the code nor
the comment on ucc_uart_pram's rx_length ("minus 1" part differs). That
comment seems a verbatim copy of that in cpm_uart/cpm_uart_core.c
anyway so perhaps it was just copied over w/o much thinking.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220830084925.5608-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Testing also CIRC_CNT() with CIRC_CNT_TO_END() is unnecessary because
to latter alone covers all necessary cases.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220823141839.165244-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to and tail with UART_XMIT_SIZE - 1 because tail is
already on valid range.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220823141839.165244-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Testing also CIRC_CNT() with CIRC_CNT_TO_END() is unnecessary because
to latter alone covers all necessary cases.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220823141839.165244-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There should be no reason to adjust old ktermios which is going to get
discarded anyway.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There should be no reason to adjust old ktermios which is going to get
discarded anyway.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assume previously used termios has a valid baudrate and use
it directly.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_clk_get_enabled() helper:
- calls devm_clk_get()
- calls clk_prepare_enable() and registers what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code, the error handling paths and avoid the need of
a dedicated function used with devm_add_action_or_reset().
That said, meson_uart_probe_clock() is now more or less the same as
devm_clk_get_enabled(), so use this function directly instead.
This also fixes an (unlikely) unchecked devm_add_action_or_reset() error.
Based on my test with allyesconfig, this reduces the .o size from:
text data bss dec hex filename
16350 5016 128 21494 53f6 drivers/tty/serial/meson_uart.o
down to:
15415 4784 128 20327 4f67 drivers/tty/serial/meson_uart.o
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/3f18638cb3cf08ed8817addca1402ed5e3bd3602.1661328361.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to check non-zeroness first and then clear. Just set to zero
unconditionally.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/3b885e7f-1372-3aa9-febd-34566ba25e3d@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A number of places want to clear IER with the same CAP_UUE trick.
Create a helper for that.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816120759.11552-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the limitation of SERIAL_FSL_LPUART=y,
as we may need enable this console while SERIAL_FSL_LPUART=m.
Signed-off-by: Jindong Yue <jindong.yue@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220802101613.30879-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Plain global GPIO numbering schema is deprecated and is being removed
from the kernel. Convert this driver to use a new GPIO descriptor based
schema.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220806225643.40897-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core already provides a helper to check if the given port
is an enabled console. Utilize it instead of open coded variant.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220806225643.40897-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the implementations can read only 32 bits because of
the interface limitations of the port they are connected to.
Add a parameter reg-io-width for supporting such platforms.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Link: https://lore.kernel.org/r/20220826120559.2122-3-shubhrajyoti.datta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the clk_enable return value.
If clocks are not enabled the register accesses could hang the
system so error out instead.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/20220729114748.18332-8-shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a potential infinite loop while waiting for the
the TXFULL to deassert. Adds the error message and timeout to
avoid infinite loop if it fails to get the TX fifo not full.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/20220729114748.18332-7-shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the ignore_status is not considered in the isr.
Add a check to add the ignore_status.
Fixes: 61ec901698 ("tty/serial: add support for Xilinx PS UART")
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/20220729114748.18332-5-shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialise the read status in probe.
It will be checked in the isr so to have the default values lets initialise
in probe.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/20220729114748.18332-4-shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on recommended guidance Copyright term should be also present in
front of (c). That's why aligned drivers to match this pattern.
It helps automated tools with source code scanning.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/20220729114748.18332-3-shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If clocks are not enabled the register access may hang the system.
Check for the clock enable return value and bail out if not enabled.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/20220729114748.18332-2-shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With Broadcom Broadband arch ARCH_BCMBCA supported in the kernel, this
patch series migrate the ARCH_BCM4908 symbol to ARCH_BCMBCA. Hence
replace ARCH_BCM4908 with ARCH_BCMBCA in subsystem Kconfig files.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> (for watchdog)
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (for drivers/pci)
Acked-by: Wolfram Sang <wsa@kernel.org> (for i2c)
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> (for reset)
Link: https://lore.kernel.org/r/20220803175455.47638-7-william.zhang@broadcom.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Here is the big set of tty and serial driver changes for 6.0-rc1.
It was delayed from last week as I wanted to make sure the last commit
here got some good testing in linux-next and elsewhere as it seemed to
show up only late in testing for some reason.
Nothing major here, just lots of cleanups from Jiri and Ilpo to make the
tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo). Also
included in here is the obligatory n_gsm updates from Daniel Starke and
lots of tiny driver updates and minor fixes and tweaks for other smaller
serial drivers.
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYvD8qA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylfEQCdGiYLQkWUUarhnlocHo+kSm5vkvsAnicZg7Sl
IQBeAidA3dZEQO0lLlM5
=t7Yh
-----END PGP SIGNATURE-----
Merge tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.0-rc1.
It was delayed from last week as I wanted to make sure the last commit
here got some good testing in linux-next and elsewhere as it seemed to
show up only late in testing for some reason.
Nothing major here, just lots of cleanups from Jiri and Ilpo to make
the tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo).
Also included in here is the obligatory n_gsm updates from Daniel
Starke and lots of tiny driver updates and minor fixes and tweaks for
other smaller serial drivers.
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
tty: serial: qcom-geni-serial: Fix %lu -> %u in print statements
tty: amiserial: Fix comment typo
tty: serial: document uart_get_console()
tty: serial: serial_core, reformat kernel-doc for functions
Documentation: serial: link uart_ops properly
Documentation: serial: move GPIO kernel-doc to the functions
Documentation: serial: dedup kernel-doc for uart functions
Documentation: serial: move uart_ops documentation to the struct
dt-bindings: serial: snps-dw-apb-uart: Document Rockchip RV1126
serial: mvebu-uart: uart2 error bits clearing
tty: serial: fsl_lpuart: correct the count of break characters
serial: stm32: make info structs static to avoid sparse warnings
serial: fsl_lpuart: zero out parity bit in CS7 mode
tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.
serial: 8250_bcm2835aux: Add missing clk_disable_unprepare()
tty: vt: initialize unicode screen buffer
serial: remove VR41XX serial driver
serial: 8250: lpc18xx: Remove redundant sanity check for RS485 flags
serial: 8250_dwlib: remove redundant sanity check for RS485 flags
dt_bindings: rs485: Correct delay values
...
- Add support for syscall stack randomization.
- Add support for atomic operations to the 32 & 64-bit BPF JIT.
- Full support for KASAN on 64-bit Book3E.
- Add a watchdog driver for the new PowerVM hypervisor watchdog.
- Add a number of new selftests for the Power10 PMU support.
- Add a driver for the PowerVM Platform KeyStore.
- Increase the NMI watchdog timeout during live partition migration, to avoid timeouts
due to increased memory access latency.
- Add support for using the 'linux,pci-domain' device tree property for PCI domain
assignment.
- Many other small features and fixes.
Thanks to: Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira Rajeev, Bagas
Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas, Greg Kroah-Hartman, Greg Kurz,
Haowen Bai, Hari Bathini, Jason A. Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg
Haefliger, Kajol Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch, Naveen N. Rao, Nayna
Jain, Nicholas Piggin, Ning Qiang, Pali Rohár, Petr Mladek, Rashmica Gupta, Sachin Sant,
Scott Cheloha, Segher Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, Zhouyi Zhou.
-----BEGIN PGP SIGNATURE-----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=tRkm
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add support for syscall stack randomization
- Add support for atomic operations to the 32 & 64-bit BPF JIT
- Full support for KASAN on 64-bit Book3E
- Add a watchdog driver for the new PowerVM hypervisor watchdog
- Add a number of new selftests for the Power10 PMU support
- Add a driver for the PowerVM Platform KeyStore
- Increase the NMI watchdog timeout during live partition migration, to
avoid timeouts due to increased memory access latency
- Add support for using the 'linux,pci-domain' device tree property for
PCI domain assignment
- Many other small features and fixes
Thanks to Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira
Rajeev, Bagas Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas,
Greg Kroah-Hartman, Greg Kurz, Haowen Bai, Hari Bathini, Jason A.
Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg Haefliger, Kajol
Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch,
Naveen N. Rao, Nayna Jain, Nicholas Piggin, Ning Qiang, Pali Rohár,
Petr Mladek, Rashmica Gupta, Sachin Sant, Scott Cheloha, Segher
Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, and Zhouyi Zhou.
* tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (191 commits)
powerpc/64e: Fix kexec build error
EDAC/ppc_4xx: Include required of_irq header directly
powerpc/pci: Fix PHB numbering when using opal-phbid
powerpc/64: Init jump labels before parse_early_param()
selftests/powerpc: Avoid GCC 12 uninitialised variable warning
powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
powerpc/xive: Fix refcount leak in xive_get_max_prio
powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
powerpc/perf: Include caps feature for power10 DD1 version
powerpc: add support for syscall stack randomization
powerpc: Move system_call_exception() to syscall.c
powerpc/powernv: rename remaining rng powernv_ functions to pnv_
powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
powerpc/powernv: Avoid crashing if rng is NULL
selftests/powerpc: Fix matrix multiply assist test
powerpc/signal: Update comment for clarity
powerpc: make facility_unavailable_exception 64s
powerpc/platforms/83xx/suspend: Remove write-only global variable
powerpc/platforms/83xx/suspend: Prevent unloading the driver
powerpc/platforms/83xx/suspend: Reorder to get rid of a forward declaration
...
There are three independent sets of changes:
- Sai Prakash Ranjan adds tracing support to the asm-generic
version of the MMIO accessors, which is intended to help
understand problems with device drivers and has been part
of Qualcomm's vendor kernels for many years.
- A patch from Sebastian Siewior to rework the handling of
IRQ stacks in softirqs across architectures, which is
needed for enabling PREEMPT_RT.
- The last patch to remove the CONFIG_VIRT_TO_BUS option and
some of the code behind that, after the last users of this
old interface made it in through the netdev, scsi, media and
staging trees.
-----BEGIN PGP SIGNATURE-----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=aTR0
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three independent sets of changes:
- Sai Prakash Ranjan adds tracing support to the asm-generic version
of the MMIO accessors, which is intended to help understand
problems with device drivers and has been part of Qualcomm's vendor
kernels for many years
- A patch from Sebastian Siewior to rework the handling of IRQ stacks
in softirqs across architectures, which is needed for enabling
PREEMPT_RT
- The last patch to remove the CONFIG_VIRT_TO_BUS option and some of
the code behind that, after the last users of this old interface
made it in through the netdev, scsi, media and staging trees"
* tag 'asm-generic-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
uapi: asm-generic: fcntl: Fix typo 'the the' in comment
arch/*/: remove CONFIG_VIRT_TO_BUS
soc: qcom: geni: Disable MMIO tracing for GENI SE
serial: qcom_geni_serial: Disable MMIO tracing for geni serial
asm-generic/io: Add logging support for MMIO accessors
KVM: arm64: Add a flag to disable MMIO trace for nVHE KVM
lib: Add register read/write tracing support
drm/meson: Fix overflow implicit truncation warnings
irqchip/tegra: Fix overflow implicit truncation warnings
coresight: etm4x: Use asm-generic IO memory barriers
arm64: io: Use asm-generic high level MMIO accessors
arch/*: Disable softirq stacks on PREEMPT_RT.
When we multiply an unsigned int by a u32 we still end up with an
unsigned int. That means we should specify "%u" not "%lu" in the
format code.
NOTE: this fix was chosen instead of somehow promoting the value to
"unsigned long" since the max baud rate from the earlier call to
uart_get_baud_rate() is 4000000 and the max sampling rate is 32.
4000000 * 32 = 0x07a12000, not even close to overflowing 32-bits.
Fixes: c474c77571 ("tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.")
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220802132250.1.Iea061e14157a17e114dbe2eca764568a02d6b889@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management
to allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and
use the firmware interfaces for system power control and for
power capping.
-----BEGIN PGP SIGNATURE-----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=0dZI
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC drivers from Arnd Bergmann:
"The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management to
allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and use
the firmware interfaces for system power control and for power
capping"
* tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (125 commits)
soc: a64fx-diag: disable modular build
dt-bindings: soc: qcom: qcom,smd-rpm: add power-controller
dt-bindings: soc: qcom: aoss: document qcom,sm8450-aoss-qmp
dt-bindings: soc: qcom,rpmh-rsc: simplify qcom,tcs-config
ARM: mach-qcom: Add support for MSM8909
dt-bindings: arm: cpus: Document "qcom,msm8909-smp" enable-method
soc: qcom: spm: Add CPU data for MSM8909
dt-bindings: soc: qcom: spm: Add MSM8909 CPU compatible
soc: qcom: rpmpd: Add compatible for MSM8909
dt-bindings: power: qcom-rpmpd: Add MSM8909 power domains
soc: qcom: smd-rpm: Add compatible for MSM8909
dt-bindings: soc: qcom: smd-rpm: Add MSM8909
soc: qcom: icc-bwmon: Remove unnecessary print function dev_err()
soc: fujitsu: Add A64FX diagnostic interrupt driver
soc: qcom: socinfo: Fix the id of SA8540P SoC
soc: qcom: Make QCOM_RPMPD depend on PM
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
...
This was the only function mentioned in the text, but was neither linked
nor documented. So document and link it, so that hyperlinking works in
the text.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220728061056.20799-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are many annotated functions in serial_core.c, but they do not
completely conform to the kernel-doc style. So reformat them and link
them from the Documentation.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220728061056.20799-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO uart functions are documented in Documentation. Move and
transform this documentation into kernel-doc directly in the code and
reference it in Documentation using kernel-doc:.
This makes it easier to update, maintain and check by the build.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220728061056.20799-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the serial (uart_*) functions are documented twice. Once as
kernel-doc along their sources and once in Documentation. So deduplicate
these texts, merge them into kernel-doc in the sources, and link them
using kernel-doc: from the Documentation.
To be properly linked and rendered, tabulators had to be removed from
the comments.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220728061056.20799-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LPUART can't distinguish between a break signal and a framing error,
so need to count the break characters if there is a framing error and
received data is zero instead of the parity error.
Fixes: 5541a9bacf ("serial: fsl_lpuart: handle break and make sysrq work")
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220725050115.12396-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The info structs are local only to the stm32-usart.c driver and are
triggering sparse warnings about being undecalred. Move these into
the main driver code and make them static to avoid the following
warnings:
drivers/tty/serial/stm32-usart.h:42:25: warning: symbol 'stm32f4_info' was not declared. Should it be static?
drivers/tty/serial/stm32-usart.h:63:25: warning: symbol 'stm32f7_info' was not declared. Should it be static?
drivers/tty/serial/stm32-usart.h:85:25: warning: symbol 'stm32h7_info' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Link: https://lore.kernel.org/r/20220721212430.453192-1-ben-linux@fluff.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LPUART hardware doesn't zero out the parity bit on the received
characters. This behavior won't impact the use cases of CS8 because
the parity bit is the 9th bit which is not currently used by software.
But the parity bit for CS7 must be zeroed out by software in order to
get the correct raw data.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20220714185858.615373-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the logic around call to clk_round_rate(), for some corner conditions,
get_clk_div_rate() could return an sub-optimal clock rate. Also, if an
exact clock rate was not found lowest clock was being returned.
Search for suitable clock rate in 2 steps
a) exact match or within 2% tolerance
b) within 5% tolerance
This also takes care of corner conditions.
Fixes: c2194bc999 ("tty: serial: qcom-geni-serial: Remove uart frequency table. Instead, find suitable frequency with call to clk_round_rate")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Link: https://lore.kernel.org/r/1657911343-1909-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error path when get clock frequency fails in bcm2835aux_serial
driver does not correctly disable the clock.
This flaw was found using a static analysis tool "Hulk Robot", which
reported the following warning when analyzing linux-next/master:
drivers/tty/serial/8250/8250_bcm2835aux.c:
warning: clk_disable_unprepare_missing.cocci
The cocci script checks for the existence of clk_disable_unprepare()
paired with clk_prepare_enable().
Add the missing clk_disable_unprepare() to the error path.
Fixes: fcc446c8aa ("serial: 8250_bcm2835aux: Add ACPI support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Guo Mengqi <guomengqi3@huawei.com>
Link: https://lore.kernel.org/r/20220715023312.37808-1-guomengqi3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d3164e2f3b ("MIPS: Remove VR41xx support") removed support
for MIPS VR41xx platform, so remove exclusive drivers for this
platform, too.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20220715140322.135825-1-tsbogend@alpha.franken.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before the drivers rs485_config() function is called the serial core
already ensures that only one of both options RTS on send or RTS after send
is set. So remove the concerning sanity check in the driver function to
avoid redundancy.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-9-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before the drivers rs485_config() function is called the serial core
already ensures that only one of both options RTS on send or RTS after send
is set. So remove the concerning sanity check in the driver function to
avoid redundancy.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-8-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the RTS delays set via device tree are not clamped to a maximum
value although the device tree bindings documentation for RS485 claims that
only a maximum of 1000 msecs is allowed.
So clamp the values to avoid arbitrary high delay settings. However clamp
the values to 100 instead of 1000 msecs to be consistent which the maximum
that is allowed when setting the delays from userspace via the UART ioctl
TIOCSRS485.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-6-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the sanitizing of RS485 delays out of uart_sanitize_serial_rs485()
into the new function uart_sanitize_serial_rs485_delays().
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-5-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In serial8250_em485_config() the termination GPIO is set with the uart_port
spinlock held. This is an issue if setting the GPIO line can sleep (e.g.
since the concerning GPIO expander is connected via SPI or I2C).
Fix this by setting the termination line outside of the uart_port spinlock
in the serial core and using gpiod_set_value_cansleep() which instead of
gpiod_set_value() allows it to sleep.
Beside fixing the termination GPIO line setting for the 8250 driver this
change also makes setting the termination GPIO generic for all UART
drivers.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-4-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ar933x_config_rs485() the check for the RTS GPIO is not needed since in
case the GPIO is not available at driver init ar933x_no_rs485 is assigned
to port->rs485_supported and this function is never called. So remove the
check.
Also in uart_set_rs485_config() the serial core already assigns the passed
serial_rs485 struct to the uart port. So remove the assignment in the
drivers rs485_config() function to avoid redundancy.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-3-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RS485 is not possible without an RTS GPIO regardless of whether RS485 is
enabled at boot time or not. So correct the concerning check in the probe()
function.
Fixes: e849145e1f ("serial: ar933x: Fill in rs485_supported")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-2-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9cabe26e65 ("serial: 8250_bcm7271: UART errors after resuming
from S2") prevented an early enabling of RTS during resume, but it did
not actively restore the RTS state after resume.
Fixes: 9cabe26e65 ("serial: 8250_bcm7271: UART errors after resuming from S2")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220714031316.404918-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With PSLVERR_RESP_EN parameter set to 1, the device generates an error
response when an attempt to read an empty RBR with FIFO enabled.
This happens when LCR writes are ignored when UART is busy.
dw8250_check_lcr() in retries to update LCR, invokes dw8250_force_idle()
to clear and reset FIFO and eventually reads UART_RX causing the error.
Avoid this by not reading RBR/UART_RX when no data is available.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: VAMSHI GAJJELA <vamshigajjela@google.com>
Link: https://lore.kernel.org/r/20220713131722.2316829-1-vamshigajjela@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
S3C2410_UCON is a 32bit register, so it must be read with rd_regl()
instead of rd_reg(), otherwise the upper bits will be zeroed. Fix this.
Fixes: 72a43046b6 ("tty: serial: samsung_tty: loopback mode support")
Tested-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220712140745.30362-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Aspeed Virtual UART is only present on Aspeed BMC platforms. Hence
add a dependency on ARCH_ASPEED, to prevent asking the user about this
driver when configuring a kernel without Aspeed BMC support.
Reviewed-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/259138c372d433005b4871789ef9ee8d15320307.1657528861.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for some of the Brainboxes PCIe (PX) range of
serial cards, including the PX-101, PX-235/PX-246,
PX-203/PX-257, PX-260/PX-701, PX-310, PX-313,
PX-320/PX-324/PX-376/PX-387, PX-335/PX-346, PX-368, PX-420,
PX-803 and PX-846.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/AM5PR0202MB2564669252BDC59BF55A6E87C4879@AM5PR0202MB2564.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
-----BEGIN PGP SIGNATURE-----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=O/9g
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=yTZT
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom SoC drivers updatse for 5.20, please
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
* tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux:
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
phy: brcm-sata: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
i2c: brcmstb: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
ata: ahci_brcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
soc: bcm: bcm2835-power: Bypass power_on/off() calls
soc: bcm: bcm2835-power: Add support for BCM2711's RPiVid ASB
soc: bcm: bcm2835-power: Resolve ASB register macros
soc: bcm: bcm2835-power: Refactor ASB control
mfd: bcm2835-pm: Add support for BCM2711
mfd: bcm2835-pm: Use 'reg-names' to get resources
soc: bcm: brcmstb: biuctrl: Add missing of_node_put()
soc: bcm: brcmstb: pm: pm-arm: fix typo in comment
Link: https://lore.kernel.org/r/20220711164451.3542127-6-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Prepare for the BCM63138 ARCH_BCM_63XX migration to ARCH_BCMBCA. Make
SERIAL_BCM63XX depending on ARCH_BCMBCA.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
When DT provides rs485-term, set termination flag as supported.
Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220704094515.6831-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Embed rs485_supported to uart_port to allow serial core to tweak it as
needed.
Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220704094515.6831-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Freescale 8250 implementations have the problem that a single long
break results in one irq per character frame time. The code in
fsl8250_handle_irq() that is supposed to handle that uses the BI bit in
lsr_saved_flags to detect such a situation and then skip the second
received character. However it also stores other error bits and so after
a single frame error the character received in the next irq handling is
passed to the upper layer with a frame error, too.
So after a spike on the data line (which is correctly recognized as a
frame error) the following valid character is thrown away, because the
driver reports a frame error for that one, too.
To weaken this problem restrict saving LSR to only the BI bit.
Note however that the handling is still broken:
- lsr_saved_flags is updated using orig_lsr which is the LSR content
for the first received char, but there might be more in the FIFO, so
a character is thrown away that is received later and not necessarily
the one following the break.
- The doubled break might be the 2nd and 3rd char in the FIFO, so the
workaround doesn't catch these, because serial8250_rx_chars() doesn't
handle the workaround.
- lsr_saved_flags might have set UART_LSR_BI at the entry of
fsl8250_handle_irq() which doesn't originate from
fsl8250_handle_irq()'s "up->lsr_saved_flags |= orig_lsr &
UART_LSR_BI;" but from e.g. from serial8250_tx_empty().
- For a long or a short break this isn't about two characters, but more
or only a single one.
Fixes: 9deaa53ac7 ("serial: add irq handler for Freescale 16550 errata.")
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220704085119.55900-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per RZ/N1 peripheral user manual(r01uh0752ej0100-rzn1-peripheral.pdf)
rev 1.0.0 Mar,2019, the value for 8_WORD_BURST is 4(b2,b1=2’b10).
This patch fixes the macro as per the user manual.
Fixes: aa63d786ce ("serial: 8250: dw: Add support for DMA flow controlling devices")
Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220630083909.4294-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions tty_termios_encode_baud_rate() and uart_update_timeout() should
be called with the baudrate value which was set to hardware. Linux then
report exact values via ioctl(TCGETS2) to userspace.
Change mvebu_uart_baud_rate_set() function to return baudrate value which
was set to hardware and propagate this value to above mentioned functions.
With this change userspace would see precise value in termios c_ospeed
field.
Fixes: 68a0db1d7d ("serial: mvebu-uart: add function to change baudrate")
Cc: stable <stable@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220628100922.10717-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When console is enabled, univ8250_console_setup() calls
serial8250_console_setup() before .dev is set to uart_port. Therefore,
it will not call pm_runtime_get_sync(). Later, when the actual driver
is going to take over univ8250_console_exit() is called. As .dev is
already set, serial8250_console_exit() makes pm_runtime_put_sync() call
with usage count being zero triggering PM usage count warning
(extra debug for univ8250_console_setup(), univ8250_console_exit(), and
serial8250_register_ports()):
[ 0.068987] univ8250_console_setup ttyS0 nodev
[ 0.499670] printk: console [ttyS0] enabled
[ 0.717955] printk: console [ttyS0] printing thread started
[ 1.960163] serial8250_register_ports assigned dev for ttyS0
[ 1.976830] printk: console [ttyS0] disabled
[ 1.976888] printk: console [ttyS0] printing thread stopped
[ 1.977073] univ8250_console_exit ttyS0 usage:0
[ 1.977075] serial8250 serial8250: Runtime PM usage count underflow!
[ 1.977429] dw-apb-uart.6: ttyS0 at MMIO 0x4010006000 (irq = 33, base_baud = 115200) is a 16550A
[ 1.977812] univ8250_console_setup ttyS0 usage:2
[ 1.978167] printk: console [ttyS0] printing thread started
[ 1.978203] printk: console [ttyS0] enabled
To fix the issue, call pm_runtime_get_sync() in
serial8250_register_ports() as soon as .dev is set for an uart_port
if it has console enabled.
This problem became apparent only recently because 82586a7215 ("PM:
runtime: Avoid device usage count underflows") added the warning
printout. I confirmed this problem also occurs with v5.18 (w/o the
warning printout, obviously).
Fixes: bedb404e91 ("serial: 8250_port: Don't use power management for kernel console")
Cc: stable <stable@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/b4f428e9-491f-daf2-2232-819928dc276e@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If port->mapbase = NULL in serial8250_request_std_resource() , it need
return a error code instead of 0. If uart_set_info() fail to request new
regions by serial8250_request_std_resource() but the return value of
serial8250_request_std_resource() is 0, The system incorrectly considers
that the resource application is successful and does not attempt to
restore the old setting. A null pointer reference is triggered when the
port resource is later invoked.
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220628083515.64138-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code lacks clearing of previous DEAT/DEDT values. Thus, changing
values on the fly results in garbage delays tending towards the maximum
value as more and more bits are ORed together. (Leaving RS485 mode
would have cleared the old values though).
Fixes: 1bcda09d29 ("serial: stm32: add support for RS485 hardware control mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220627150753.34510-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Place dw8250_serial_out() before dw8250_serial_out38x() so that it can
be called from dw8250_serial_out38x() to do the actual write.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220628134234.53771-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of open-coding, use BIT(), GENMASK(), and FIELD_GET() helpers.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220630100536.41329-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop CONFIG_PM and CONFIG_PM_SLEEP ifdeffery while converting dw8250_pm_ops
to use new PM macros. Since we are using runtime PM, wrap dw8250_pm_ops into
pm_ptr().
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220630100507.31113-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the sake of better maintenance, sort included headers alphabetically.
While at it, split the serial group of headers which makes clear the
subsystem the driver belongs to.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220630093816.28271-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the earlycon parameter is given twice, the kernel will spit out a
WARN() in register_console() because it was already registered. The
non-dt variant setup_earlycon() already handles that gracefully. The dt
variant of_setup_earlycon() doesn't. Add the check there and add the
-EALREADY handling in early_init_dt_scan_chosen_stdout().
FWIW, this doesn't happen if CONFIG_ACPI_SPCR_TABLE is set. In that case
the registration is delayed until after earlycon parameter(s) are
parsed.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220628120705.200617-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing LSR requires port lock because it mutates lsr_saved_flags
in serial_lsr_in().
Fixes: 197eb5c416 ("serial: 8250_dw: Use serial_lsr_in() in dw8250_handle_irq()")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/c5879db7-bee9-93f-526e-872a292442@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Internal loopback mode can be supported by setting
UCON register's Loopback Mode bit. The mode & bit can be supported
since s3c2410 and later SoCs. The prefix of LOOPBACK / BIT(5) naming
should be also changed to S3C2410_ in order to avoid confusion.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220629004141.51484-1-chanho61.park@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Regarding Exynos Auto v9 SoC, it supports uarts up to 12. However, the
maximum number of the ports has been derived from
CONFIG_SERIAL_SAMSUNG_UARTS and tightly coupled with the config for
previous Samsung SoCs such as s3c24xx and s3c64xx. To overcome this
limitation, this changes the usage of the definition to UART_NR which is
widely used from other serial drivers. This also defines the value to 12
only for ARM64 SoCs to not affect the change to previous arm32 SoCs.
Instead of enumerating all the ports as predefined arrays, this
introduces s3c24xx_serial_init_port_default that is initializing the
structure as the default value.
Reviewed-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220629005538.60132-1-chanho61.park@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e8ffbb71f7 ("serial: 8250: use THRE & __stop_tx also with
DMA") changed __dma_tx_complete() to enable THRI that is cleared in
__stop_tx() once THRE is asserted as UART runs out bits to transmit. It
is possible, however, that more data arrives in between in which case
serial8250_tx_dma() resumes Tx. THRI is not supposed to be on during
DMA Tx because DMA is based on completion handler, therefore THRI must
be cleared unconditionally in serial8250_tx_dma().
When Tx is about to start, another race window exists with
serial8250_handle_irq() leading to a call into __stop_tx() while the
Tx has already been resumed:
__tx_complete():
-> spin_lock(port->lock)
-> dma->tx_running = 0
-> serial8250_set_THRI()
-> spin_unlock(port->lock)
uart_start():
serial8250_handle_irq():
-> spin_lock(port->lock)
-> serial8250_tx_dma():
-> dma->tx_running = 1
-> spin_unlock(port->lock)
-> spin_lock(port->lock)
-> __stop_tx()
Close this race by checking !dma->tx_running before calling into
__stop_tx().
Fixes: e8ffbb71f7 ("serial: 8250: use THRE & __stop_tx also with DMA")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220615090651.15340-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver must provide throttle and unthrottle in uart_ops when it
sets UPSTAT_AUTORTS. Add them using existing stop_rx &
enable_interrupts functions.
Fixes: 2a76fa2830 (serial: pl011: Adopt generic flag to store auto RTS status)
Cc: stable <stable@kernel.org>
Cc: Lukas Wunner <lukas@wunner.de>
Reported-by: Nuno Gonçalves <nunojpg@gmail.com>
Tested-by: Nuno Gonçalves <nunojpg@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220614075637.8558-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The src_maxburst and dst_maxburst have been changed to 1 but the settings
of the UCON register aren't changed yet. They should be changed as well
according to the dmaengine slave config.
Fixes: aa2f80e752 ("serial: samsung: fix maxburst parameter for DMA transactions")
Cc: stable <stable@kernel.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220627065113.139520-1-chanho61.park@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ffd381445e ("serial: 8250: dw: Move the USR register to pdata")
caused NULL-pointer dereference when booting with ACPI by unconditional
usage of the recently added pdata.
In order to fix that and prevent similar issues in future, hook the
default version of this structure in dw8250_acpi_match table.
While at it, sort all entries alphabetically.
Fixes: ffd381445e ("serial: 8250: dw: Move the USR register to pdata")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20220620121046.1307412-1-mw@semihalf.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 9th bit multipoint addressing mode for DW UART. 9th bit addressing
can be used only when HW RS485 is available.
Updating RAR (receive address register) is bit tricky because busy
indication is not be available when DW UART is strictly 16550
compatible, which is the case with the hardware I was testing with. RAR
should not be updated while receive is in progress which is now
achieved by deasserting RE and waiting for one frame (in case rx would
be in progress, the driver seems to have no way of knowing it w/o busy
indication). Because of this complexity, it's better to avoid doing it
unless really needed.
Co-developed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Raymond Tan <raymond.tan@intel.com>
Co-developed-by: Lakshmi Sowjanya <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Lakshmi Sowjanya <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for RS-485 multipoint addressing using 9th bit [*]. The
addressing mode is configured through ->rs485_config().
ADDRB in termios indicates 9th bit addressing mode is enabled. In this
mode, 9th bit is used to indicate an address (byte) within the
communication line. ADDRB can only be enabled/disabled through
->rs485_config() that is also responsible for setting the destination and
receiver (filter) addresses.
Add traps to detect unwanted changes to struct serial_rs485 layout using
static_assert().
[*] Technically, RS485 is just an electronic spec and does not itself
specify the 9th bit addressing mode but 9th bit seems at least
"semi-standard" way to do addressing with RS485.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be able to alter ADDRB within ->rs485_config(), take termios_rwsem
before calling ->rs485_config() and pass termios.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use 32-bit reads in order to not lose higher bits of DW UART regs. This
change does not fix any known issue as the high bits are not used for
anything related to 8250 driver (dw8250_readl_ext and dw8250_writel_ext
used within the dwlib are already doing
readl/writel/ioread32be/iowrite32be anyway).
This change is necessary to enables 9th bit address mode. DW UART
reports address frames with BIT(8) of LSR.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DW flags address received as BIT(8) in LSR. In order to not lose that
on read, enlarge lsr_saved_flags to u16.
Adjust lsr/status variables and related call chains to use u16.
Technically, some of these type conversion would not be needed but it
doesn't hurt to be consistent.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per file BOTH_EMPTY defines are littering our source code here and
there. Define once in serial.h and create helper for the check
too.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both UART_XMIT_SIZE and SERIAL_XMIT_SIZE are defined. Make them all
UART_XMIT_SIZE.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use C99 array initializer insteads of comments and make unmapped checks
more obvious.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using UART_* to name defines is a bit problematic. When trying to do
unrelated cleanup which also involved tweaking header inclusion logic,
caused UART_CSR from serial_reg.h to leak into msm's namespace which is
also among msm defines. Thus, rename all UART_* ones to MSM_UART_* to
eliminate possibility of collisions.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create static inline instead of define as it provides type safety and
is safer wrt. macros expansion.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for clk_prepare_enable() at the beginning of
atmel_console_setup() and clk_disable_unprepare() at the end of
atmel_console_setup() as the clock is already enabled when calling
atmel_console_setup() and its disablement is done at the end
of probe.
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220616140024.2081238-4-claudiu.beznea@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_clk_get() for serial clock instead of clk_get()/clk_put().
With this move the clk_get in driver's probe function.
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220616140024.2081238-3-claudiu.beznea@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop using legacy PM ops and switch using dev_pm_ops. Along with
it #ifdef CONFIG_PM are removed and __maybe_unused and pm_ptr() used
instead. Coding style recommends (at chapter Conditional Compilation)
to avoid using preprocessor conditional and use __maybe_unused
instead.
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220616140024.2081238-2-claudiu.beznea@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In soc_info(), of_find_node_by_type() will return a node pointer
with refcount incremented. We should use of_node_put() when it is
not used anymore.
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220618060850.4058525-1-windhl@126.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In tegra_uart_init(), of_find_matching_node() will return a node
pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220615111747.3963930-1-windhl@126.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 31f6bd7fad ("serial: Store character timing information
to uart_port"), per frame timing information is available on uart_port.
Uart port's timeout can be derived from frame_time by multiplying with
fifosize.
Most callers of uart_poll_timeout are not made under port's lock. To be
on the safe side, make sure frame_time is only accessed once. As
fifo_size is effectively a constant, it shouldn't cause any issues.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220613113905.22962-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch mpc5xxx_get_bus_frequency() to use fwnode in order to help
cleaning up other parts of the kernel from OF specific code.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # for i2c-mpc
Acked-by: Wolfram Sang <wsa@kernel.org> # for the I2C part
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for mscan/mpc5xxx_can
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220507100147.5802-2-andriy.shevchenko@linux.intel.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmKvgdceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0qMH/RnVz4BvYXVWWc1t
+4NT9N20pNzrByzUxSBsrLfL5BNIt9fNjrS0WLs4HlzExbiixvKIBHPkDZoCo1gQ
wxoqpJf2BMxmdXH46/wWdSszbdPk33eLM/MfYE2QfnmtYsDSLZQMzOUAcdh6qD53
ty9br3IM/g4ixCwxKRt3NNixjin4wTTxR5ZD2E5k0JAaT+4FW5llRvq92dA1UOq7
JeGRLkc2l0211MFLo0vtuPOyWMIQL8t98rKTzevwoVY7R9I/0uUJCbkU7mb9wMUY
yKYlTN/4ZikTTSxa8NpQsXHqTyOHaKmS5F6oE4sw9VurHI2u3Jmxy9j9AwO1Pn8C
JUizMCk=
=qqcu
-----END PGP SIGNATURE-----
Merge tag 'v5.19-rc3' into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable MMIO tracing for geni serial driver to prevent excessive
logging. Any access over serial console would involve a lot of
TX and RX register accesses (and few others), so these MMIO
read/write trace events in these drivers cause a lot of unwanted
noise because of the high frequency of such operations and it is
not very useful tracing these events for such drivers.
Given we want to enable these trace events on development devices
(maybe not production devices) where performance also really matters
so that we don't regress other components by wasting CPU cycles and
memory collecting these traces, it makes more sense to disable these
traces from such drivers.
Also another reason to disable these traces would be to prevent
recursive tracing when we display the trace buffer containing
these MMIO trace events since writing onto serial console would
further record MMIO traces.
Signed-off-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Not all LSR register flags are preserved across reads. Therefore, LSR
readers must store the non-preserved bits into lsr_save_flags.
This fix was initially mixed into feature commit f6f586102a ("serial:
8250: Handle UART without interrupt on TEMT using em485"). However,
that feature change had a flaw and it was reverted to make room for
simpler approach providing the same feature. The embedded fix got
reverted with the feature change.
Re-add the lsr_save_flags fix and properly mark it's a fix.
Link: https://lore.kernel.org/all/1d6c31d-d194-9e6a-ddf9-5f29af829f3@linux.intel.com/T/#m1737eef986bd20cf19593e344cebd7b0244945fc
Fixes: e490c9144c ("tty: Add software emulated RS485 support for 8250")
Cc: stable <stable@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@penugtronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/f4d774be-1437-a550-8334-19d8722ab98c@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core handles serial_rs485 sanitization.
When em485 init fails, there are two possible paths of entry:
1) uart_rs485_config (init path) that fully clears port->rs485 on
error.
2) ioctl path with a pre-existing, valid port->rs485 unto which the
kernel falls back on error and port->rs485 should therefore be
kept untouched. The temporary rs485 struct is not returned to
userspace in case of error so its flag don't matter.
...Thus SER_RS485_ENABLED clearing on error can/should be dropped.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-37-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core handles serial_rs485 assignment. It is safe to remove this
assignment because sc16is7xx_reg_proc() takes port.lock at start (and
sc16is7xx_reconf_rs485() would too).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-36-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver provides different rs485_supported for the case where RTS is
not available making it unnecessary to handle it in
imx_uart_rs485_config.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-32-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core handles serial_rs485 sanitization. Remove custom
sanitization from lpuart_config_rs485.
This change loses dev_err when SER_RS485_RX_DURING_TX is set due to
incorrect configuration. Other drivers do not do similar prinout for
full-duplex case and it should be done in serial core if it is
desirable to notify on this condition. Personally, I doesn't see it
important because the kernel gracefully downgrades to half-duplex.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-31-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core handles serial_rs485 sanitization and rs485 struct
assignment. As serial_rs485 is already clear for the non-RS485 case by
serial core, there no need to clear flags in the driver.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-26-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to be add new flags more cleanly and safely, return -EINVAL
from TIOCSRS485 ioctl for the flags bits which are not among the
current legacy ones.
This might cause a regression for userspace as those non-flag bits do
not currently trigger -EINVAL. However, it would only occur if the
userspace is sending garbage bits so perhaps we'll get away with this
change.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-25-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When SER_RS485_ENABLED is not set, having any other flag/field set in
serial_rs485 struct does not have an effect different from not having
them set. Thus, make the serial_rs485 struct also match the behavior
for all flags, not just SER_RS485_ENABLED.
Some drivers do similar clearing of rs485 struct in their
rs485_config() already, but not all. This change makes the behavior
consistent across drivers.
Don't try to validate rs485 struct further when no RS485 is requested,
this silences some bogus warnings.
This change has (minor) userspace visible impact.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-24-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sanitize serial_rs485 struct before calling into rs485_setup. The
drivers provide supported_rs485 to help sanitization of the fields.
If neither of SER_RS485_RTS_ON_SEND or SER_RS485_RTS_AFTER_SEND
supported, don't pretend they can be set to sane settings but clear
them both instead. If only one of them is supported it may look
tempting to use the one driver supports to set the other, however, the
userspace does not have that information readily available so it
wouldn't be helpful.
While adjusting the documentation, remove also the claim that
TIOCGRS485 would call driver specific code. In reality, it does nothing
else than copies the stored serial_rs485 structure from uart_port to
userspace.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-23-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add information on supported serial_rs485 features.
This driver does not support delay_rts_after_send but the pre-existing
behavior is to return -EINVAL if delay_rts_after_send is non-zero. In
contrast, other drivers that do not support delay_rts_after_send either
zero delay_rts_after_send or do not care (leave the inaccurate value).
As changing this would cause userspace visible impact, the change is
not attempted here. But perhaps it should be still tried (maybe nobody
finds that kind of API oddity significant)?
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-21-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add information on supported serial_rs485 features.
In the case where RTS is lacking, RS485 cannot be enabled so provide
zero rs485_supported for that case. Perhaps it would make sense to not
provide rs485_config() at all in that case but such a change would have
userspace visible impact/change in behavior so this patch does not
attempt it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-17-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add information on supported serial_rs485 features.
In the case where RTS is lacking, RS485 cannot be enabled so provide
zero rs485_supported for that case. Perhaps it would make sense to not
provide rs485_config() at all in that case but such a change would have
userspace visible impact/change in behavior so this patch does not
attempt it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-14-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add information on supported serial_rs485 features. When the driver is
using em485, take advantage of serial8250_em485_supported.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preparing to move serial_rs485 struct sanitization into serial core,
each driver has to provide what fields/flags it supports. This
information is pointed into by rs485_supported.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few serial drivers make a call to rs485_config() themselves (all
these seem to relate to init). Convert them all to use a common helper
which makes it easy to make adjustments on tasks related to it as
serial_rs485 struct sanitization is going to be added.
In pci_fintek_setup() (in 8250_pci.c), the rs485_config() call was made
with NULL, however, it can be changed to pass uart_port's rs485 struct.
No other callers should pass NULL into rs485_config() so the NULL check
can now be eliminated.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure LSR flags are preserved in dw8250_tx_wait_empty(). This
function is called from a low-level out function and therefore cannot
call serial_lsr_in() as it would lead to infinite recursion.
It is borderline if the flags need to be saved here at all since this
code relates to writing LCR register which usually implies no important
characters should be arriving.
Fixes: 914eaf935e ("serial: 8250_dw: Allow TX FIFO to drain before writing to UART_LCR")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220608095431.18376-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dw8250_handle_irq() reads LSR under a few conditions, convert both to
use serial_lsr_in() in order to preserve LSR flags properly across
reads.
Fixes: 424d79183a ("serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt")
Fixes: aa63d786ce ("serial: 8250: dw: Add support for DMA flow controlling devices")
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220608095431.18376-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_rx_chars() has max_count based character limit. If it
triggers, the function returns the old LSR value (and it has never
returned only flags which were not handled). Adjust the comment to
match behavior and warn about which flags can be depended on.
I'd have moved LSR read before LSR read and used serial_lsr_in() also
here but I came across an old discussion about the topic. That
discussion generated commit d22f8f1068 ("serial: 8250: Fix lost rx
state") so I left the code as it is (it works as long as the callers
only use a subset of the LSR flags which holds true today) and changed
the comment instead.
Link: https://www.spinics.net/lists/linux-serial/msg16220.html
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220608095431.18376-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_handle_irq() assumes it's the first to read LSR register.
However, there are 8250 drivers which perform LSR read in their own irq
handler prior to calling serial8250_handle_irq(). As not all flags are
preserved across LSR reads, use serial_lsr_in() helper to get all the
preserved flags.
This commit might fix other commits too besides the ones for DW UART
mentioned below. It's just not clear to me which of the other devices
clear some of the LSR flags on read. AFAIK, nobody has complained about
this problem (either against DW or other devices) so it might not have
that bad impact in the end.
Fixes: 424d79183a ("serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt")
Fixes: aa63d786ce ("serial: 8250: dw: Add support for DMA flow controlling devices")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220608095431.18376-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LSR register readers need to be careful in order to not lose bits that
are not preserved across reads. Create a helper that takes care of
storing the non-preserved bits into lsr_save_flags.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220608095431.18376-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all LSR register flags are preserved across reads. Therefore, LSR
readers must store the non-preserved bits into lsr_save_flags.
This fix was initially mixed into feature commit f6f586102a ("serial:
8250: Handle UART without interrupt on TEMT using em485"). However,
that feature change had a flaw and it was reverted to make room for
simpler approach providing the same feature. The embedded fix got
reverted with the feature change.
Re-add the lsr_save_flags fix and properly mark it's a fix.
Link: https://lore.kernel.org/all/1d6c31d-d194-9e6a-ddf9-5f29af829f3@linux.intel.com/T/#m1737eef986bd20cf19593e344cebd7b0244945fc
Fixes: e490c9144c ("tty: Add software emulated RS485 support for 8250")
Co-developed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220608095431.18376-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As either start_tx_rs485() or start_tx() calls __start_tx() as the last
line of their logic, it makes sense to just move that call into
start_tx(). When start_tx_rs485() wants to defer tx using timer, return
false so start_tx() can return based on it.
Reorganize em485 code in serial8250_start_tx() so that the return can be
shared for the cases where tx start is deferred.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220607084154.8172-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There seems to be little reason for __do_stop_tx() to exits on its own.
It is rather simple and is only called from __stop_tx(). Thus, move its
logic into __stop_tx().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220607084154.8172-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I2C implementation on this chip has a few key differences
compared to SPI, as described in previous patches.
* extended register space access needs no extra logic
* slave address is used to select which UART to communicate
with
To accommodate these differences, add an I2C interface config,
set the RevID register address and implement an empty method
for setting the GlobalCommand register, since no special handling
is needed for the extended register space.
To handle the port-specific slave address, create an I2C dummy
device for each port, except the base one (UART0), which is
expected to be the one specified in firmware, and create a
regmap for each I2C device.
Add minimum and maximum slave addresses to each devtype for
sanity checking.
Also, use a separate regmap config with no write_flag_mask,
since I2C has a R/W bit in its slave address, and set the
max register to the address of the RevID register, since the
extended register space needs no extra logic.
Finally, add the I2C driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-5-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPI can only use 5 address bits, since one bit is reserved for
specifying R/W and 2 bits are used to specify the UART port.
To access registers that have addresses past 0x1F, an extended
register space can be enabled by writing to the GlobalCommand
register (address 0x1F).
I2C uses 8 address bits. The R/W bit is placed in the slave
address, and so is the UART port. Because of this, registers
that have addresses higher than 0x1F can be accessed normally.
To access the RevID register, on SPI, 0xCE must be written to
the 0x1F address to enable the extended register space, after
which the RevID register is accessible at address 0x5. 0xCD
must be written to the 0x1F address to disable the extended
register space.
On I2C, the RevID register is accessible at address 0x25.
Create an interface config struct, and add a method for
toggling the extended register space and a member for the RevId
register address. Implement these for SPI.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-4-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently does manual register manipulation in
multiple places to talk to a specific UART port.
In order to talk to a specific UART port over SPI, the bits U1
and U0 of the register address can be set, as explained in the
Command byte configuration section of the datasheet.
Make this more elegant by creating regmaps for each UART port
and setting the read_flag_mask and write_flag_mask
accordingly.
All communcations regarding global registers are done on UART
port 0, so replace the global regmap entirely with the port 0
regmap.
Also, remove the 0x1f masks from reg_writeable(), reg_volatile()
and reg_precious() methods, since setting the U1 and U0 bits of
the register address happens inside the regmap core now.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-3-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SPI batch read/write operations can be implemented as simple
regmap raw read and write, which will also try to do a gather
write just as it is done here.
Use the regmap raw read and write methods.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-2-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit a5ddc498e7 (serial: pmac_zilog: remove unfinished DBDMA
support), the header is unused and can be removed. So do so.
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Suggested-by: "Ilpo Järvinen" <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220602083120.22519-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In suspend sequence stop_rx will be performed only if implementation for
start_rx callback is present.
Set qcom_geni_serial_start_rx as callback for start_rx so that stop_rx is
performed.
Fixes: c9d2325cdb ("serial: core: Do stop_rx in suspend path for console if console_suspend is disabled")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Link: https://lore.kernel.org/r/1654627965-1461-3-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In suspend sequence there is a need to perform stop_rx during suspend
sequence to prevent any asynchronous data over rx line. However this
can cause problem to drivers which dont do re-start_rx during set_termios.
Add new callback start_rx and perform stop_rx only when implementation of
start_rx is present. Also add call to start_rx in resume sequence so that
drivers who come across this problem can make use of this framework.
Fixes: c9d2325cdb ("serial: core: Do stop_rx in suspend path for console if console_suspend is disabled")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Link: https://lore.kernel.org/r/1654627965-1461-2-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of tty and serial driver updates for 5.19-rc1.
Lots of tiny cleanups in here, the major stuff is:
- termbit cleanups and unification by Ilpo. A much needed
change that goes a long way to making things simpler for all
of the different arches
- tty documentation cleanups and movements to their own place in
the documentation tree
- old tty driver cleanups and fixes from Jiri to bring some
existing drivers into the modern world
- RS485 cleanups and unifications to make it easier for
individual drivers to support this mode instead of having to
duplicate logic in each driver
- Lots of 8250 driver updates and additions
- new device id additions
- n_gsm continued fixes and cleanups
- other minor serial driver updates and cleanups
All of these have been in linux-next for weeks with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpndTg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykFegCgizjLDyOepr72zMDWWdp0bBTekz8AoMWODfJY
vB8/kzu329DImJMFB8ET
=rmv0
-----END PGP SIGNATURE-----
Merge tag 'tty-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.19-rc1.
Lots of tiny cleanups in here, the major stuff is:
- termbit cleanups and unification by Ilpo. A much needed change that
goes a long way to making things simpler for all of the different
arches
- tty documentation cleanups and movements to their own place in the
documentation tree
- old tty driver cleanups and fixes from Jiri to bring some existing
drivers into the modern world
- RS485 cleanups and unifications to make it easier for individual
drivers to support this mode instead of having to duplicate logic
in each driver
- Lots of 8250 driver updates and additions
- new device id additions
- n_gsm continued fixes and cleanups
- other minor serial driver updates and cleanups
All of these have been in linux-next for weeks with no reported issues"
* tag 'tty-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (166 commits)
tty: Rework receive flow control char logic
pcmcia: synclink_cs: Don't allow CS5-6
serial: stm32-usart: Correct CSIZE, bits, and parity
serial: st-asc: Sanitize CSIZE and correct PARENB for CS7
serial: sifive: Sanitize CSIZE and c_iflag
serial: sh-sci: Don't allow CS5-6
serial: txx9: Don't allow CS5-6
serial: rda-uart: Don't allow CS5-6
serial: digicolor-usart: Don't allow CS5-6
serial: uartlite: Fix BRKINT clearing
serial: cpm_uart: Fix build error without CONFIG_SERIAL_CPM_CONSOLE
serial: core: Do stop_rx in suspend path for console if console_suspend is disabled
tty: serial: qcom-geni-serial: Remove uart frequency table. Instead, find suitable frequency with call to clk_round_rate.
dt-bindings: serial: renesas,em-uart: Add RZ/V2M clock to access the registers
serial: 8250_fintek: Check SER_RS485_RTS_* only with RS485
Revert "serial: 8250_mtk: Make sure to select the right FEATURE_SEL"
serial: msm_serial: disable interrupts in __msm_console_write()
serial: meson: acquire port->lock in startup()
serial: 8250_dw: Use dev_err_probe()
serial: 8250_dw: Use devm_add_action_or_reset()
...
The asm-generic tree contains three separate changes for linux-5.19:
- The h8300 architecture is retired after it has been effectively
unmaintained for a number of years. This is the last architecture we
supported that has no MMU implementation, but there are still a few
architectures (arm, m68k, riscv, sh and xtensa) that support CPUs with
and without an MMU.
- A series to add a generic ticket spinlock that can be shared by most
architectures with a working cmpxchg or ll/sc type atomic, including
the conversion of riscv, csky and openrisc. This series is also a
prerequisite for the loongarch64 architecture port that will come as
a separate pull request.
- A cleanup of some exported uapi header files to ensure they can be
included from user space without relying on other kernel headers.
-----BEGIN PGP SIGNATURE-----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=ri2Q
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"The asm-generic tree contains three separate changes for linux-5.19:
- The h8300 architecture is retired after it has been effectively
unmaintained for a number of years. This is the last architecture
we supported that has no MMU implementation, but there are still a
few architectures (arm, m68k, riscv, sh and xtensa) that support
CPUs with and without an MMU.
- A series to add a generic ticket spinlock that can be shared by
most architectures with a working cmpxchg or ll/sc type atomic,
including the conversion of riscv, csky and openrisc. This series
is also a prerequisite for the loongarch64 architecture port that
will come as a separate pull request.
- A cleanup of some exported uapi header files to ensure they can be
included from user space without relying on other kernel headers"
* tag 'asm-generic-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
h8300: remove stale bindings and symlink
sparc: add asm/stat.h to UAPI compile-test coverage
powerpc: add asm/stat.h to UAPI compile-test coverage
mips: add asm/stat.h to UAPI compile-test coverage
riscv: add linux/bpf_perf_event.h to UAPI compile-test coverage
kbuild: prevent exported headers from including <stdlib.h>, <stdbool.h>
agpgart.h: do not include <stdlib.h> from exported header
csky: Move to generic ticket-spinlock
RISC-V: Move to queued RW locks
RISC-V: Move to generic spinlocks
openrisc: Move to ticket-spinlock
asm-generic: qrwlock: Document the spinlock fairness requirements
asm-generic: qspinlock: Indicate the use of mixed-size atomics
asm-generic: ticket-lock: New generic ticket-based spinlock
remove the h8300 architecture
This series has been 12 years in the making, it mostly finishes the
work that was started with the founding of Linaro to clean up platform
support in the kernel.
The largest change here is a cleanup of the omap1 platform, which
is the final ARM machine type to get converted to the common-clk
subsystem. All the omap1 specific drivers are now made independent of the
mach/*.h headers to allow the platform to be part of a generic ARMv4/v5
multiplatform kernel. The last bit that enables this support is still
missing here while we wait for some last dependencies to make it into
the mainline kernel through other subsystems.
The s3c24xx, ixp4xx, iop32x, ep93xx and dove platforms were all almost
at the point of allowing multiplatform kernels, this work gets completed
here along with a few additional cleanup. At the same time, the s3c24xx
and s3c64xx are now deprecated and expected to get removed in the future.
The PXA and OMAP1 bits are in a separate branch because of dependencies.
Once both branches are merged, only the three Intel StrongARM platforms
(RiscPC, Footbridge/NetWinder and StrongARM1100) need separate kernels,
and there are no plans to include these.
-----BEGIN PGP SIGNATURE-----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=CTtN
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARMv4T/v5 multiplatform support from Arnd Bergmann:
"This series has been 12 years in the making, it mostly finishes the
work that was started with the founding of Linaro to clean up platform
support in the kernel.
The largest change here is a cleanup of the omap1 platform, which is
the final ARM machine type to get converted to the common-clk
subsystem. All the omap1 specific drivers are now made independent of
the mach/*.h headers to allow the platform to be part of a generic
ARMv4/v5 multiplatform kernel.
The last bit that enables this support is still missing here while we
wait for some last dependencies to make it into the mainline kernel
through other subsystems.
The s3c24xx, ixp4xx, iop32x, ep93xx and dove platforms were all almost
at the point of allowing multiplatform kernels, this work gets
completed here along with a few additional cleanup. At the same time,
the s3c24xx and s3c64xx are now deprecated and expected to get removed
in the future.
The PXA and OMAP1 bits are in a separate branch because of
dependencies. Once both branches are merged, only the three Intel
StrongARM platforms (RiscPC, Footbridge/NetWinder and StrongARM1100)
need separate kernels, and there are no plans to include these"
* tag 'arm-multiplatform-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: ixp4xx: Consolidate Kconfig fixing issue
ARM: versatile: Add missing of_node_put in dcscb_init
ARM: config: Refresh IXP4xx config after multiplatform
ARM: omap1: add back omap_set_dma_priority() stub
ARM: omap: fix missing declaration warnings
ARM: omap: fix address space warnings from sparse
ARM: spear: remove include/mach/ subdirectory
ARM: davinci: remove include/mach/ subdirectory
ARM: omap2: remove include/mach/ subdirectory
integrator: remove empty ap_init_early()
ARM: s3c: fix include path
MAINTAINERS: omap1: Add Janusz as an additional maintainer
ARM: omap1: htc_herald: fix typos in comments
ARM: OMAP1: fix typos in comments
ARM: OMAP1: clock: Remove noop code
ARM: OMAP1: clock: Remove unused code
ARM: OMAP1: clock: Fix UART rate reporting algorithm
ARM: OMAP1: clock: Fix early UART rate issues
ARM: OMAP1: Prepare for conversion of OMAP1 clocks to CCF
ARM: omap1: fix build with no SoC selected
...
Not much dramatic changes at this time, but we've received quite
a lot of changes for ASoC, while there are still a few fixes and
quirks for usual HD- and USB-auido. Here are some highlights.
* ASoC:
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs
- Initial stages of Intel AVS driver merge
- Introduction of v4 IPC mechanism for SOF
- TDM mode support for AK4613
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
* Others
- A few regression fixes after the USB-audio endpoint management
refactoring
- More enhancements for Cirrus HD-audio codec support (still ongoing)
- Addition of generic serial MIDI driver
-----BEGIN PGP SIGNATURE-----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=5qBk
-----END PGP SIGNATURE-----
Merge tag 'sound-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Not much dramatic changes at this time, but we've received quite a lot
of changes for ASoC, while there are still a few fixes and quirks for
usual HD- and USB-auido. Here are some highlights.
ASoC:
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs
- Initial stages of Intel AVS driver merge
- Introduction of v4 IPC mechanism for SOF
- TDM mode support for AK4613
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
Others:
- A few regression fixes after the USB-audio endpoint management
refactoring
- More enhancements for Cirrus HD-audio codec support (still ongoing)
- Addition of generic serial MIDI driver"
* tag 'sound-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (504 commits)
ALSA: hda/realtek - Add new type for ALC245
ALSA: usb-audio: Configure sync endpoints before data
ALSA: ctxfi: fix typo in comment
ALSA: cs5535audio: fix typo in comment
ALSA: ctxfi: Add SB046x PCI ID
ALSA: usb-audio: Add missing ep_idx in fixed EP quirks
ALSA: usb-audio: Workaround for clock setup on TEAC devices
ALSA: lola: Bounds check loop iterator against streams array size
ASoC: max98090: Move check for invalid values before casting in max98090_put_enab_tlv()
ASoC: rt1308-sdw: add the default value of register 0xc320
ASoC: rt9120: Use pm_runtime and regcache to optimize 'pwdnn' logic
ASoC: rt9120: Fix 3byte read, valule offset typo
ASoC: amd: acp: Set Speaker enable/disable pin through rt1019 codec driver.
ASoC: amd: acp: Set Speaker enable/disable pin through rt1019 codec driver
ASoC: wm2000: fix missing clk_disable_unprepare() on error in wm2000_anc_transition()
ASoC: codecs: lpass: Fix passing zero to 'PTR_ERR'
ASoC: SOF: sof-client-ipc-flood-test: use pm_runtime_resume_and_get()
ASoC: SOF: mediatek: remove duplicate include in mt8195.c
ASoC: SOF: mediatek: Add mt8195 debug dump
ASoC: SOF: mediatek: Add mediatek common debug dump
...
This is quite a big update, partly due to the addition of some larger
drivers (more of which is to follow since at least the AVS driver is
still a work in progress) and partly due to Charles' work sorting out
our handling of endianness. As has been the case recently it's much
more about drivers than the core.
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs.
- Initial stages of Intel AVS driver merge.
- Introduction of v4 IPC mechanism for SOF.
- TDM mode support for AK4613.
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKLf5EACgkQJNaLcl1U
h9ASqAf/YnwbFP919ree/DEKUDCNc4klUH5M4JOexXbZlZDqxKYRGZjoLuiwX/PQ
Au/xOjGEvm3Yg5/g5c8YFVNcIkv1O8VclRkV59oIxlBwKmQeTKvq+lOmlel2l1wZ
XOmvHjE46wxH1N1cLwL6KkX0YDn59orSZGYZRpfLjL61y6LQWsLNU0tY6AWCRATB
Llnrbu+DYgCsYNTEOOOY5s4V+4LkQm8TLdft91Va7mBdkPPRFoXRO0HGcVBqbkoN
7pf2mrjrLAWL9yuA8FlrgJbHq58DF9WGe5uEU7qlVL1zw46ClgIM0ABxPOdNdjV2
Wzb1jI7GmztgQNxlR9BcJB0kxAj9vA==
=oD5l
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.19' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.19
This is quite a big update, partly due to the addition of some larger
drivers (more of which is to follow since at least the AVS driver is
still a work in progress) and partly due to Charles' work sorting out
our handling of endianness. As has been the case recently it's much
more about drivers than the core.
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs.
- Initial stages of Intel AVS driver merge.
- Introduction of v4 IPC mechanism for SOF.
- TDM mode support for AK4613.
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
Add CSIZE sanitization for unsupported CSIZE configurations. In
addition, if parity is asked for but CSx was unsupported, the sensible
result is CS8+parity which requires setting USART_CR1_M0 like with 9
bits.
Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: c8a9d04394 (serial: stm32: fix word length configuration)
Cc: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only CS7 and CS8 seem supported but CSIZE is not sanitized from CS5 or
CS6 to CS8. In addition, ASC_CTL_MODE_7BIT_PAR suggests that CS7 has
to have parity, thus add PARENB.
Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: c4b0585607 (serial:st-asc: Add ST ASC driver.)
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only CS8 is supported but CSIZE was not sanitized to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Similarly, INPCK, PARMRK, and BRKINT are reported textually unsupported
but were not cleared in termios c_iflag which is the machine-readable
format.
Fixes: 45c054d081 (tty: serial: add driver for the SiFive UART)
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only CS7 and CS8 seem supported but CSIZE is not sanitized from
CS5 or CS6 to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: 1da177e4c3 (Linux-2.6.12-rc2)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
