``max_count`` negative values are not used. Since ``port->fifosize``
is an unsigned int, make ``max_count`` the same.
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-13-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment brings no benefit as we can already see from the method's
name, ``s3c24xx_serial_pm``, that it deals with power management.
Drop the superfluous comment.
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-12-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move open brace '{' following function definition on the next line.
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-11-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Braces {} are not necessary for single statement blocks.
Remove braces on single statement block.
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-10-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All registers of the IP have 32 bits. Use u32 variables when reading
or writing from/to the registers. The purpose of those variables becomes
clearer.
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-9-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
samsung_tty.c uses u32 and relies on <linux/console.h> to include
<linux/types.h>. Explicitly include <linux/types.h>. We shall aim to
have the driver self contained.
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-8-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sorting headers alphabetically helps locating duplicates,
and makes it easier to figure out where to insert new headers.
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-7-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The entire bus (PERIC) on which the GS101 serial resides only allows
32-bit register accesses. The reg-io-width dt property is disallowed
for the "google,gs101-uart" compatible and instead the iotype is
inferred from the compatible. Always set UPIO_MEM32 iotype for the
gs101 earlycon.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-6-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GS101's Connectivity Peripheral blocks (peric0/1 blocks) which
include the I3C and USI (I2C, SPI, UART) only allow 32-bit
register accesses.
Instead of specifying the reg-io-width = 4 everywhere, for each node,
the requirement should be deduced from the compatible.
Infer UPIO_MEM32 iotype from the "google,gs101-uart" compatible.
Update the uart info name to be GS101 specific in order to
differentiate from the other exynos platforms. All the other settings
are not changed.
exynos_fifoszdt_serial_drv_data was replaced by gs101_serial_drv_data
because the iotype restriction is gs101 specific and there was no other
user of exynos_fifoszdt_serial_drv_data.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-5-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GS101's Connectivity Peripheral blocks (peric0/1 blocks) which
include the I3C and USI (I2C, SPI, UART) only allow 32-bit
register accesses. If using 8-bit register accesses, a SError
Interrupt is raised causing the system unusable.
Instead of specifying the reg-io-width = 4 everywhere, for each node,
the requirement should be deduced from the compatible.
Prepare the samsung tty driver to allow IO types different than
UPIO_MEM. ``struct uart_port::iotype`` is an unsigned char where all
its 8 bits are exposed to uapi. We can't make NULL checks on it to
verify if it's set, thus always set it from the driver's data.
Use u8 for the ``iotype`` member of ``struct s3c24xx_uart_info`` to
emphasize that the iotype is an 8 bit mask.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-4-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The core expects for tx_empty() either TIOCSER_TEMT when the tx is
empty or 0 otherwise. s3c24xx_serial_txempty_nofifo() might return
0x4, and at least uart_get_lsr_info() tries to clear exactly
TIOCSER_TEMT (BIT(1)). Fix tx_empty() to return TIOCSER_TEMT.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-2-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix indentation and add line after do/while() block.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-18-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add comments about I2C slave address structure, and reformat to
improve readability.
Also reformat some comments according to kernel coding style.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-17-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following checkpatch warnings:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
With this change, the affected functions now match the prototypes in
struct gpio_chip.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-16-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify driver by defining a common function to handle the power
control of all variants.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-15-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify driver by defining a common function to handle the detection
of all variants.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-14-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GENMASK() is preferred when defining bitmasks.
Of all the masks changed, only MAX310x_REV_MASK is actually used.
No functional change.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-13-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace dev_err() with dev_err_probe().
This helps in simplifing code and standardizing the error output.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-12-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows to simplify code by removing the break statement in the default
switch/case in some functions.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-11-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify error handling and only call uart_remove_one_port() if line bit
is set, instead of having to manually set s->p[i].port.dev to NULL.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-10-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a separate regmap name for each port so they can each have their own
debugfs entry, allowing to access each port registers independently.
For example, a four channels/ports device like the MAX14830 will have four
entries in its regmap debugfs:
$ find /sys/kernel/debug/regmap -type d | grep spi0.0
/sys/kernel/debug/regmap/spi0.0-port0
/sys/kernel/debug/regmap/spi0.0-port1
/sys/kernel/debug/regmap/spi0.0-port2
/sys/kernel/debug/regmap/spi0.0-port3
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/all/77f101f1-897d-4e6d-a8fd-27b818caf768@cesnet.cz/
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-9-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running pahole shows that there are some holes within the
max310x_devtype structure.
Remove holes and optimize alignment by reorganizing structure members.
This can also lead to data structure size reduction for some CPUs.
On 64-bit CPU (arm64):
Before:
/* size: 40, cachelines: 1, members: 6 */
/* sum members: 34, holes: 2, sum holes: 6 */
/* last cacheline: 40 bytes */
After:
/* size: 40, cachelines: 1, members: 6 */
/* padding: 6 */
/* last cacheline: 40 bytes */
On 32-bit CPU (i386):
Before:
/* size: 32, cachelines: 1, members: 6 */
/* sum members: 26, holes: 2, sum holes: 6 */
/* last cacheline: 32 bytes */
After:
/* size: 24, cachelines: 1, members: 8 */
/* padding: 2 */
/* last cacheline: 24 bytes */
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace g with q.
Helpful when grepping thru source code or logs for
"request" keyword.
Fixes: f65444187a ("serial: New serial driver MAX310X")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use preferred spi_get_device_match_data() instead of
device_get_match_data() and spi_get_device_id() to get the driver match
data.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use preferred i2c_get_match_data() instead of device_get_match_data()
to get the driver match data.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows to instantiate a max14830 I2C device from userspace.
Helpful when testing driver with i2c-stub.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When trying to instantiate a max14830 device from userspace:
echo max14830 0x60 > /sys/bus/i2c/devices/i2c-2/new_device
we get the following error:
Unable to handle kernel NULL pointer dereference at virtual address...
...
Call trace:
max310x_i2c_probe+0x48/0x170 [max310x]
i2c_device_probe+0x150/0x2a0
...
Add check for validity of devtype to prevent the error, and abort probe
with a meaningful error message.
Fixes: 2e1f2d9a9b ("serial: max310x: implement I2C support")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since STM32MP25, FIFO size could vary regarding the STM32MPxx version.
So we get this size from "hwcfgr1" register and compute threshold values
corresponding to the ratio given by reference manual.
As STM32MP1x, STM32MP25 and STM32H7 share the same compatible and STM32H7
doesn't have a register to get FIFO size, we force FIFO size to 16 in case
of zero read from hwcfgr1 register.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20240112095300.2004878-5-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USART has registers above 0xff offset, so extend variable type to u16.
And change UNDEF_REG to 0xffff.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20240112095300.2004878-4-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32MP25x got 9 instances of U(S)ART. So extend STM32_MAX_PORTS to 9, in
order to handle all instances.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20240112095300.2004878-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case of high USART input clock and low baud rate, BRR value
is not enough to get correct baud rate. So here we use USART prescaler to
divide USART input clock to get the correct baud rate.
PRESC register is only available since stm32h7.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20240112095300.2004878-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of commit d7402513c9 ("arm64: smp: IPI_CPU_STOP and
IPI_CPU_CRASH_STOP should try for NMI"), if we've got pseudo-NMI
enabled then we'll use it to stop CPUs at panic time. This is nice,
but it does mean that there's a pretty good chance that we'll end up
stopping a CPU while it holds the port lock for the console
UART. Specifically, I see a CPU get stopped while holding the port
lock nearly 100% of the time on my sc7180-trogdor based Chromebook by
enabling the "buddy" hardlockup detector and then doing:
sysctl -w kernel.hardlockup_all_cpu_backtrace=1
sysctl -w kernel.hardlockup_panic=1
echo HARDLOCKUP > /sys/kernel/debug/provoke-crash/DIRECT
UART drivers are _supposed_ to handle this case OK and this is why
UART drivers check "oops_in_progress" and only do a "trylock" in that
case. However, before we enabled pseudo-NMI to stop CPUs it wasn't a
very well-tested situation.
Now that we're testing the situation a lot, it can be seen that the
Qualcomm GENI UART driver is pretty broken. Specifically, when I run
my test case and look at the console output I just see a bunch of
garbled output like:
[ 201.069084] NMI backtrace[ 201.069084] NM[ 201.069087] CPU: 6
PID: 10296 Comm: dnsproxyd Not tainted 6.7.0-06265-gb13e8c0ede12
#1 01112b9f14923cbd0b[ 201.069090] Hardware name: Google Lazor
([ 201.069092] pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DI[
201.069095] pc : smp_call_function_man[ 201.069099]
That's obviously not so great. This happens because each call to the
console driver exits after the data has been written to the FIFO but
before it's actually been flushed out of the serial port. When we have
multiple calls into the console one after the other then (if we can't
get the lock) each call tells the UART to throw away any data in the
FIFO that hadn't been transferred yet.
I've posted up a patch to change the arm64 core to avoid this
situation most of the time [1] much like x86 seems to do, but even if
that patch lands the GENI driver should still be fixed.
>From testing, it appears that we can just delete the cancel/abort in
the case where we weren't able to get the UART lock and the output
looks good. It makes sense that we'd be able to do this since that
means we'll just call into __qcom_geni_serial_console_write() and
__qcom_geni_serial_console_write() looks much like
qcom_geni_serial_poll_put_char() but with a loop. However, it seems
safest to poll the FIFO and make sure it's empty before our
transfer. This should reliably make sure that we're not
interrupting/clobbering any existing transfers.
As part of this change, we'll also avoid re-setting up a TX at the end
of the console write function if we weren't able to get the lock,
since accessing "port->tx_remaining" without the lock is not
safe. This is only needed to re-start userspace initiated transfers.
[1] https://lore.kernel.org/r/20231207170251.1.Id4817adef610302554b8aa42b090d57270dc119c@changeid
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240112150307.2.Idb1553d1d22123c377f31eacb4486432f6c9ac8d@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In linflex_config_port() the member variable type will be
assigned again. Remove redundant uart type assignment from
linflex_probe().
Signed-off-by: Lizhe <sensor1010@163.com>
Link: https://lore.kernel.org/r/20240112133923.190852-1-sensor1010@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This includes everything from part 2:
* Support for tuning for systems with fast misaligned accesses.
* Support for SBI-based suspend.
* Support for the new SBI debug console extension.
* The T-Head CMOs now use PA-based flushes.
* Support for enabling the V extension in kernel code.
* Optimized IP checksum routines.
* Various ftrace improvements.
* Support for archrandom, which depends on the Zkr extension.
and then also a fix for those:
* The build is no longer broken under NET=n, KUNIT=y for ports that
don't define their own ipv6 checksum.
-----BEGIN PGP SIGNATURE-----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=Sjhj
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- Support for tuning for systems with fast misaligned accesses.
- Support for SBI-based suspend.
- Support for the new SBI debug console extension.
- The T-Head CMOs now use PA-based flushes.
- Support for enabling the V extension in kernel code.
- Optimized IP checksum routines.
- Various ftrace improvements.
- Support for archrandom, which depends on the Zkr extension.
- The build is no longer broken under NET=n, KUNIT=y for ports that
don't define their own ipv6 checksum.
* tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (56 commits)
lib: checksum: Fix build with CONFIG_NET=n
riscv: lib: Check if output in asm goto supported
riscv: Fix build error on rv32 + XIP
riscv: optimize ELF relocation function in riscv
RISC-V: Implement archrandom when Zkr is available
riscv: Optimize hweight API with Zbb extension
riscv: add dependency among Image(.gz), loader(.bin), and vmlinuz.efi
samples: ftrace: Add RISC-V support for SAMPLE_FTRACE_DIRECT[_MULTI]
riscv: ftrace: Add DYNAMIC_FTRACE_WITH_DIRECT_CALLS support
riscv: ftrace: Make function graph use ftrace directly
riscv: select FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
lib/Kconfig.debug: Update AS_HAS_NON_CONST_LEB128 comment and name
riscv: Restrict DWARF5 when building with LLVM to known working versions
riscv: Hoist linker relaxation disabling logic into Kconfig
kunit: Add tests for csum_ipv6_magic and ip_fast_csum
riscv: Add checksum library
riscv: Add checksum header
riscv: Add static key for misaligned accesses
asm-generic: Improve csum_fold
RISC-V: selftests: cbo: Ensure asm operands match constraints
...
Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty core
and drivers in here, along with the usual set of rs485 updates (someday
this might work properly...) Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaeUaw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykyOgCgp1uhP/b9iW6qM7qL6OYEG6idI0kAnj0VASNm
vSI69HmdKKwo69YLOSBp
=14n1
-----END PGP SIGNATURE-----
Merge tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty
core and drivers in here, along with the usual set of rs485 updates
(someday this might work properly...)
Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (197 commits)
serial: sc16is7xx: refactor EFR lock
serial: sc16is7xx: reorder code to remove prototype declarations
serial: sc16is7xx: refactor FIFO access functions to increase commonality
serial: sc16is7xx: drop unneeded MODULE_ALIAS
serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
serial: sc16is7xx: add explicit return for some switch default cases
serial: sc16is7xx: add macro for max number of UART ports
serial: sc16is7xx: add driver name to struct uart_driver
serial: sc16is7xx: use i2c_get_match_data()
serial: sc16is7xx: use spi_get_device_match_data()
serial: sc16is7xx: use DECLARE_BITMAP for sc16is7xx_lines bitfield
serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()
serial: sc16is7xx: remove obsolete loop in sc16is7xx_port_irq()
serial: sc16is7xx: set safe default SPI clock frequency
serial: sc16is7xx: add check for unsupported SPI modes during probe
serial: sc16is7xx: fix invalid sc16is7xx_lines bitfield in case of probe error
serial: 8250_exar: Set missing rs485_supported flag
serial: omap: do not override settings for RS485 support
serial: core, imx: do not set RS485 enabled if it is not supported
serial: core: make sure RS485 cannot be enabled when it is not supported
...
A new drivers/cache/ subsystem is added to contain drivers for abstracting
cache flush methods on riscv and potentially others, as this is needed for
handling non-coherent DMA but several SoCs require nonstandard hardware
methods for it.
op-tee gains support for asynchronous notification with FF-A, as well
as support for a system thread for executing in secure world.
The tee, reset, bus, memory and scmi subsystems have a couple of minor
updates.
Platform specific soc driver changes include:
- Samsung Exynos gains driver support for Google GS101 (Tensor G1)
across multiple subsystems
- Qualcomm Snapdragon gains support for SM8650 and X1E along with
added features for some other SoCs
- Mediatek adds support for "Smart Voltage Scaling" on MT8186 and MT8195,
and driver support for MT8188 along with some code refactoring.
- Microchip Polarfire FPGA support for "Auto Update" of the FPGA bitstream
- Apple M1 mailbox driver is rewritten into a SoC driver
- minor updates on amlogic, mvebu, ti, zynq, imx, renesas and hisilicon
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmWeypsACgkQYKtH/8kJ
UifCpxAA0CMZRXKZOuTw9we2eS9rCy5nBrJsDiEAi9UPgQYUIrD7BVng+PAMN5UD
AeEDEjUEmZ+a4hyDDPxwdlhI2qIvIITAZ1qbwcElXvt41MTIyo+1BK+kI6A7oxHd
oPh9kG0yRjb5tNc6utrHbXpEb6AxfXYcdAOzA2YRonqKohYUJlGqHtAub2Dqd6FD
nuYXGXSZKWMpd0L1X7nuD8+uBj8DbQgq0HfhiAj3vUgzwkYk/SlTo/DYByJOQeMA
HE1X/vG7qwrdHC4VNXaiJJ/GQ6ZXAZXdK+F97v+FtfClPVuxAffMlTbb6t/CyiVb
4HrVzduyNMlIh8OqxLXabXJ0iJ970wkuPlOZy2pZmgkV5oKGSXSGxXWAwMvOmCVO
RSgetXYHX3gDGQ59Si+LsEQhORdChMMik5nBPdyxj1UK3QsObV40qLpHBae7GWnA
Qb6+3FrtnbiHfOMxGmhC4lqDfgSfByW1BspxsFyy33wb+TPfYJzOnXYe8aYTZ1iw
GSuWNa/uHF61Q2v0d3Lt09GhUh9wWradnJ+caxpB0B0MHG2QQqFI8EVwIEn1/spu
bWpItLT8UUDgNx+F9KRzP3HqwqbDzd9fnojSPescTzudpvpP9MC5X3w05pQ6iA1x
HFJ+2J/ENvDAHWSAySn7Qx4JKSeLxm1YcquXQW2sVTVwFTkqigw=
=4bKY
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"A new drivers/cache/ subsystem is added to contain drivers for
abstracting cache flush methods on riscv and potentially others, as
this is needed for handling non-coherent DMA but several SoCs require
nonstandard hardware methods for it.
op-tee gains support for asynchronous notification with FF-A, as well
as support for a system thread for executing in secure world.
The tee, reset, bus, memory and scmi subsystems have a couple of minor
updates.
Platform specific soc driver changes include:
- Samsung Exynos gains driver support for Google GS101 (Tensor G1)
across multiple subsystems
- Qualcomm Snapdragon gains support for SM8650 and X1E along with
added features for some other SoCs
- Mediatek adds support for "Smart Voltage Scaling" on MT8186 and
MT8195, and driver support for MT8188 along with some code
refactoring.
- Microchip Polarfire FPGA support for "Auto Update" of the FPGA
bitstream
- Apple M1 mailbox driver is rewritten into a SoC driver
- minor updates on amlogic, mvebu, ti, zynq, imx, renesas and
hisilicon"
* tag 'soc-drivers-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (189 commits)
memory: ti-emif-pm: Convert to platform remove callback returning void
memory: ti-aemif: Convert to platform remove callback returning void
memory: tegra210-emc: Convert to platform remove callback returning void
memory: tegra186-emc: Convert to platform remove callback returning void
memory: stm32-fmc2-ebi: Convert to platform remove callback returning void
memory: exynos5422-dmc: Convert to platform remove callback returning void
memory: renesas-rpc-if: Convert to platform remove callback returning void
memory: omap-gpmc: Convert to platform remove callback returning void
memory: mtk-smi: Convert to platform remove callback returning void
memory: jz4780-nemc: Convert to platform remove callback returning void
memory: fsl_ifc: Convert to platform remove callback returning void
memory: fsl-corenet-cf: Convert to platform remove callback returning void
memory: emif: Convert to platform remove callback returning void
memory: brcmstb_memc: Convert to platform remove callback returning void
memory: brcmstb_dpfe: Convert to platform remove callback returning void
soc: qcom: llcc: Fix LLCC_TRP_ATTR2_CFGn offset
firmware: qcom: qseecom: fix memory leaks in error paths
dt-bindings: clock: google,gs101: rename CMU_TOP gate defines
soc: qcom: llcc: Fix typo in kernel-doc
dt-bindings: soc: qcom,aoss-qmp: document the X1E80100 Always-On Subsystem side channel
...
We extend the existing RISC-V SBI earlycon support to use the new
RISC-V SBI debug console extension.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231124070905.1043092-4-apatel@ventanamicro.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Move common code for EFR lock/unlock of mutex into functions for code reuse
and clarity.
With the addition of old_lcr, move irda_mode within struct sc16is7xx_one to
reduce memory usage:
Before: /* size: 752, cachelines: 12, members: 10 */
After: /* size: 744, cachelines: 12, members: 10 */
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-17-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move/reorder some functions to remove sc16is7xx_ier_set() and
sc16is7xx_stop_tx() prototypes declarations.
No functional change.
sc16is7xx_ier_set() was introduced in
commit cc4c1d05eb ("sc16is7xx: Properly resume TX after stop").
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-16-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify FIFO access functions by avoiding to declare
a struct sc16is7xx_port *s variable within each function.
This is mainly done to have more commonality between the max310x and
sc16is7xx drivers.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-15-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MODULE_DEVICE_TABLE() already creates the proper aliases for the
SPI driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-14-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To better show why the limit is what it is, since we have only 16 bits for
the divisor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-13-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows to simplify code by removing the break statement in the default
switch/case in some functions.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-12-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the driver name is displayed instead of "unknown" when
displaying the driver infos:
Before:
grep ttySC /proc/tty/drivers
unknown /dev/ttySC 243 0-7 serial
After:
grep ttySC /proc/tty/drivers
sc16is7xx /dev/ttySC 243 0-7 serial
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-10-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use preferred i2c_get_match_data() instead of device_get_match_data()
and i2c_client_get_device_id() to get the driver match data.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-9-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use preferred spi_get_device_match_data() instead of
device_get_match_data() and spi_get_device_id() to get the driver match
data.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-8-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the explicit sc16is7xx_lines bitfield declaration with the generic
macro DECLARE_BITMAP() to reserve just enough memory to contain all
required bits.
This also improves code self-documentation by showing the maximum number
of bits required.
This conversion now makes sc16is7xx_lines an array, so drop the "&" before
sc16is7xx_lines in all bit access functions.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify and improve readability by replacing while(1) loop with
do {} while, and by using the keep_polling variable as the exit
condition, making it more explicit.
Fixes: 8344498721 ("sc16is7xx: Fix for multi-channel stall")
Cc: <stable@vger.kernel.org>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8344498721 ("sc16is7xx: Fix for multi-channel stall") changed
sc16is7xx_port_irq() from looping multiple times when there was still
interrupts to serve. It simply changed the do {} while(1) loop to a
do {} while(0) loop, which makes the loop itself now obsolete.
Clean the code by removing this obsolete do {} while(0) loop.
Fixes: 8344498721 ("sc16is7xx: Fix for multi-channel stall")
Cc: <stable@vger.kernel.org>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
15 MHz is supported only by 76x variants.
If the SPI clock frequency is not specified, use a safe default clock value
of 4 MHz that is supported by all variants.
Also use HZ_PER_MHZ macro to improve readability.
Fixes: 2c837a8a8f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an error occurs during probing, the sc16is7xx_lines bitfield may be left
in a state that doesn't represent the correct state of lines allocation.
For example, in a system with two SC16 devices, if an error occurs only
during probing of channel (port) B of the second device, sc16is7xx_lines
final state will be 00001011b instead of the expected 00000011b.
This is caused in part because of the "i--" in the for/loop located in
the out_ports: error path.
Fix this by checking the return value of uart_add_one_port() and set line
allocation bit only if this was successful. This allows the refactor of
the obfuscated for(i--...) loop in the error path, and properly call
uart_remove_one_port() only when needed, and properly unset line allocation
bits.
Also use same mechanism in remove() when calling uart_remove_one_port().
Fixes: c64349722d ("sc16is7xx: support multiple devices")
Cc: <stable@vger.kernel.org>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.
Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).
Cc: <stable@vger.kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-8-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers RS485 support is deactivated if there is no RTS GPIO available.
This is done by nullifying the ports rs485_supported struct. After that
however the settings in serial_omap_rs485_supported are assigned to the
same structure unconditionally, which results in an unintended reactivation
of RS485 support.
Fix this by moving the assignment to the beginning of
serial_omap_probe_rs485() and thus before uart_get_rs485_mode() gets
called.
Also replace the assignment of rs485_config() to have the complete RS485
setup in one function.
Fixes: e2752ae3cf ("serial: omap: Disallow RS-485 if rts-gpio is not specified")
Cc: <stable@vger.kernel.org>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240103061818.564-7-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the imx driver cannot support RS485 it nullifies the ports
rs485_supported structure. But it still calls uart_get_rs485_mode() which
may set the RS485_ENABLED flag nevertheless.
This may lead to an attempt to configure RS485 even if it is not supported
when the flag is evaluated in uart_configure_port() at port startup.
Avoid this by bailing out of uart_get_rs485_mode() if the RS485_ENABLED
flag is not supported by the caller.
With this fix a check for RTS availability is now obsolete in the imx
driver, since it can not evaluate to true any more. So remove this check.
Furthermore the explicit nullifcation of rs485_supported is not needed,
since the memory has already been set to zeros at allocation. So remove
this, too.
Fixes: 00d7a00e2a ("serial: imx: Fill in rs485_supported")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240103061818.564-6-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some uart drivers specify a rs485_config() function and then decide later
to disable RS485 support for some reason (e.g. imx and ar933).
In these cases userspace may be able to activate RS485 via TIOCSRS485
nevertheless, since in uart_set_rs485_config() an existing rs485_config()
function indicates that RS485 is supported.
Make sure that this is not longer possible by checking the uarts
rs485_supported.flags instead and bailing out if SER_RS485_ENABLED is not
set.
Furthermore instead of returning an empty structure return -ENOTTY if the
RS485 configuration is requested via TIOCGRS485 but RS485 is not supported.
This has a small impact on userspace visibility but it is consistent with
the -ENOTTY error for TIOCGRS485.
Fixes: e849145e1f ("serial: ar933x: Fill in rs485_supported")
Fixes: 55e18c6b6d ("serial: imx: Remove serial_rs485 sanitization")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-5-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Among other things uart_sanitize_serial_rs485() tests the sanity of the RTS
settings in a RS485 configuration that has been passed by userspace.
If RTS-on-send and RTS-after-send are both set or unset the configuration
is adjusted and RTS-after-send is disabled and RTS-on-send enabled.
This however makes only sense if both RTS modes are actually supported by
the driver.
With commit be2e2cb1d2 ("serial: Sanitize rs485_struct") the code does
take the driver support into account but only checks if one of both RTS
modes are supported. This may lead to the errorneous result of RTS-on-send
being set even if only RTS-after-send is supported.
Fix this by changing the implemented logic: First clear all unsupported
flags in the RS485 configuration, then adjust an invalid RTS setting by
taking into account which RTS mode is supported.
Cc: <stable@vger.kernel.org>
Fixes: be2e2cb1d2 ("serial: Sanitize rs485_struct")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-4-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the RS485 feature RX-during-TX is supported by means of a GPIO set the
according supported flag. Otherwise setting this feature from userspace may
not be possible, since in uart_sanitize_serial_rs485() the passed RS485
configuration is matched against the supported features and unsupported
settings are thereby removed and thus take no effect.
Cc: <stable@vger.kernel.org>
Fixes: 163f080eb7 ("serial: core: Add option to output RS485 RX_DURING_TX state via GPIO")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-3-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both the imx and stm32 driver set the rx-during-tx GPIO in rs485_config().
Since this function is called with the port lock held, this can be a
problem in case that setting the GPIO line can sleep (e.g. if a GPIO
expander is used which is connected via SPI or I2C).
Avoid this issue by moving the GPIO setting outside of the port lock into
the serial core and thus making it a generic feature.
Also with commit c54d485436 ("serial: stm32: Add support for rs485
RX_DURING_TX output GPIO") the SER_RS485_RX_DURING_TX flag is only set if a
rx-during-tx GPIO is _not_ available, which is wrong. Fix this, too.
Furthermore reset old GPIO settings in case that changing the RS485
configuration failed.
Fixes: c54d485436 ("serial: stm32: Add support for rs485 RX_DURING_TX output GPIO")
Fixes: ca530cfa96 ("serial: imx: Add support for RS485 RX_DURING_TX output GPIO")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-2-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In PCI1XXXX C0 endpoint, support for Burst mode is added.
pci1xxxx_handle_irq checks the burst status and based on that
incoming characters are received in DWORDs, RX handling is done
in pci1xxxx_rx_burst. While reading the burst status the RX error
is checked and the corresponding error statistics are updated.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20231215151123.41812-4-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Different Host drivers can attempt to access system registers
simultaneously from different memory spaces at the same time. The
syslock mechanism provides a safe option for reading UART system
registers and prevents conflicts by serializing access. Added
three padding bytes in the structure for memory alignment.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20231215151123.41812-3-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Structure declarations in 8250_pci1xxxx.c have been moved above
the functions for code readability.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20231215151123.41812-2-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_kmemdup() helper to copy dma_param instead of doing it manually.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20240102055006.27256-1-raag.jadav@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After switching the serial interface of the Moxa RS232 PCIe boards, it
fails to reset to RS232 when attempting to reload 8250_pci driver.
This patch set RS232 as the default setting during the initialization of
Moxa PCIe board.
Signed-off-by: Crescent CY Hsieh <crescentcy.hsieh@moxa.com>
Link: https://lore.kernel.org/r/20240102053133.9795-1-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Designware UART has optional feature FIFO_MODE to implement FIFO.
Encoding FIFO capabilities through Component Parameter Register CPR is
optional and it can be enabled using parameter UART_ADD_ENCODED_PARAMS.
Driver can exercise fifo capabilities by decoding CPR if implemented
or from cpr_val provided from the dw8250_platform_data otherwise.
dw8250_setup_port() checks for CPR or cpr_val to determine FIFO size
only when Component Version (UCV) is non-zero. Bailing out early on UCV
read returning zero will leave fifosize as zero and !UART_CAP_FIFO,
hence prevent early return and continue to process CPR or cpr_val for
the driver to utilize FIFO.
Non-zero UCV implies ADDITIONAL_FEATURES=1, preventing early return
will not be an overhead here.
Signed-off-by: Vamshi Gajjela <vamshigajjela@google.com>
Link: https://lore.kernel.org/r/20231231182951.877805-1-vamshigajjela@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are register accesses in the function imx_uart_rs485_config(). The
clock must be enabled for these accesses. This was ensured by calling it
via the function uart_rs485_config() in the probe() function within the
range where the clock is enabled. With the commit 7c7f9bc986 ("serial:
Deassert Transmit Enable on probe in driver-specific way") it was removed
from the probe() function and is now only called through the function
uart_add_one_port() which is located at the end of the probe() function.
But the clock is already switched off in this area. To ensure that the
clock is enabled during register access, move the disabling of the clock
to the very end of the probe() function. To avoid leaking enabled clocks
on error also add an error path for exiting with disabling the clock.
Fixes: 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Cc: stable <stable@kernel.org>
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20231226113647.39376-1-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using a leon kernel with qemu there where no console prompt.
The root cause is the handling of the fifo size in the tx part of the
apbuart driver.
The qemu uart driver only have a very rudimentary status handling and do
not report the number of chars queued in the tx fifo in the status register.
So the driver ends up with a fifo size of 1.
In the tx path the fifo size is divided by 2 - resulting in a fifo
size of zero.
The original implementation would always try to send one char, but
after the introduction of uart_port_tx_limited() the fifo size is
respected even for the first char.
There seems to be no good reason to divide the fifo size with two - so
remove this. It looks like something copied from the original amba driver.
With qemu we now have a minimum fifo size of one char, so we show
the prompt.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Fixes: d11cc8c3c4 ("tty: serial: use uart_port_tx_limited()")
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: <linux-serial@vger.kernel.org>
Cc: <sparclinux@vger.kernel.org>
Link: https://lore.kernel.org/r/20231226121607.GA2622970@ravnborg.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check if port type is not PORT_UNKNOWN during poll_init.
The kgdboc calls the tty_find_polling_driver that check
if the serial is able to use poll_init. The poll_init calls
the uart uart_poll_init that try to configure the uart with the
selected boot parameters. The uart must be ready before setting
parameters. Seems that PORT_UNKNOWN is already used by other
functions in serial_core to detect uart status, so use the same
to avoid to use it in invalid state.
The crash happen for instance in am62x architecture where the 8250
register the platform driver after the 8250 core is initialized.
Follow the report crash coming from KGDB
Thread 2 received signal SIGSEGV, Segmentation fault.
[Switching to Thread 1]
_outb (addr=<optimized out>, value=<optimized out>) at ./include/asm-generic/io.h:584
584 __raw_writeb(value, PCI_IOBASE + addr);
(gdb) bt
This section of the code is too early because in this case
the omap serial is not probed
Thread 2 received signal SIGSEGV, Segmentation fault.
[Switching to Thread 1]
_outb (addr=<optimized out>, value=<optimized out>) at ./include/asm-generic/io.h:584
584 __raw_writeb(value, PCI_IOBASE + addr);
(gdb) bt
Thread 2 received signal SIGSEGV, Segmentation fault.
[Switching to Thread 1]
_outb (addr=<optimized out>, value=<optimized out>) at ./include/asm-generic/io.h:584
584 __raw_writeb(value, PCI_IOBASE + addr);
(gdb) bt
0 _outb (addr=<optimized out>, value=<optimized out>) at ./include/asm-generic/io.h:584
1 logic_outb (value=0 '\000', addr=18446739675637874689) at lib/logic_pio.c:299
2 0xffff80008082dfcc in io_serial_out (p=0x0, offset=16760830, value=0) at drivers/tty/serial/8250/8250_port.c:416
3 0xffff80008082fe34 in serial_port_out (value=<optimized out>, offset=<optimized out>, up=<optimized out>)
at ./include/linux/serial_core.h:677
4 serial8250_do_set_termios (port=0xffff8000828ee940 <serial8250_ports+1568>, termios=0xffff80008292b93c, old=0x0)
at drivers/tty/serial/8250/8250_port.c:2860
5 0xffff800080830064 in serial8250_set_termios (port=0xfffffbfffe800000, termios=0xffbffe, old=0x0)
at drivers/tty/serial/8250/8250_port.c:2912
6 0xffff80008082571c in uart_set_options (port=0xffff8000828ee940 <serial8250_ports+1568>, co=0x0, baud=115200, parity=110, bits=8, flow=110)
at drivers/tty/serial/serial_core.c:2285
7 0xffff800080828434 in uart_poll_init (driver=0xfffffbfffe800000, line=16760830, options=0xffff8000828f7506 <config+6> "115200n8")
at drivers/tty/serial/serial_core.c:2656
8 0xffff800080801690 in tty_find_polling_driver (name=0xffff8000828f7500 <config> "ttyS2,115200n8", line=0xffff80008292ba90)
at drivers/tty/tty_io.c:410
9 0xffff80008086c0b0 in configure_kgdboc () at drivers/tty/serial/kgdboc.c:194
10 0xffff80008086c1ec in kgdboc_probe (pdev=0xfffffbfffe800000) at drivers/tty/serial/kgdboc.c:249
11 0xffff8000808b399c in platform_probe (_dev=0xffff000000ebb810) at drivers/base/platform.c:1404
12 0xffff8000808b0b44 in call_driver_probe (drv=<optimized out>, dev=<optimized out>) at drivers/base/dd.c:579
13 really_probe (dev=0xffff000000ebb810, drv=0xffff80008277f138 <kgdboc_platform_driver+48>) at drivers/base/dd.c:658
14 0xffff8000808b0d2c in __driver_probe_device (drv=0xffff80008277f138 <kgdboc_platform_driver+48>, dev=0xffff000000ebb810)
at drivers/base/dd.c:800
15 0xffff8000808b0eb8 in driver_probe_device (drv=0xfffffbfffe800000, dev=0xffff000000ebb810) at drivers/base/dd.c:830
16 0xffff8000808b0ff4 in __device_attach_driver (drv=0xffff80008277f138 <kgdboc_platform_driver+48>, _data=0xffff80008292bc48)
at drivers/base/dd.c:958
17 0xffff8000808ae970 in bus_for_each_drv (bus=0xfffffbfffe800000, start=0x0, data=0xffff80008292bc48,
fn=0xffff8000808b0f3c <__device_attach_driver>) at drivers/base/bus.c:457
18 0xffff8000808b1408 in __device_attach (dev=0xffff000000ebb810, allow_async=true) at drivers/base/dd.c:1030
19 0xffff8000808b16d8 in device_initial_probe (dev=0xfffffbfffe800000) at drivers/base/dd.c:1079
20 0xffff8000808af9f4 in bus_probe_device (dev=0xffff000000ebb810) at drivers/base/bus.c:532
21 0xffff8000808ac77c in device_add (dev=0xfffffbfffe800000) at drivers/base/core.c:3625
22 0xffff8000808b3428 in platform_device_add (pdev=0xffff000000ebb800) at drivers/base/platform.c:716
23 0xffff800081b5dc0c in init_kgdboc () at drivers/tty/serial/kgdboc.c:292
24 0xffff800080014db0 in do_one_initcall (fn=0xffff800081b5dba4 <init_kgdboc>) at init/main.c:1236
25 0xffff800081b0114c in do_initcall_level (command_line=<optimized out>, level=<optimized out>) at init/main.c:1298
26 do_initcalls () at init/main.c:1314
27 do_basic_setup () at init/main.c:1333
28 kernel_init_freeable () at init/main.c:1551
29 0xffff8000810271ec in kernel_init (unused=0xfffffbfffe800000) at init/main.c:1441
30 0xffff800080015e80 in ret_from_fork () at arch/arm64/kernel/entry.S:857
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/r/20231224131200.266224-1-michael@amarulasolutions.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add "SER_RS485_MODE_RS422" flag to struct serial_rs485, so that serial
port can switch interface into RS422 if supported by using ioctl command
"TIOCSRS485".
By treating RS422 as a mode of RS485, which means while enabling RS422
there are two flags need to be set (SER_RS485_ENABLED and
SER_RS485_MODE_RS422), it would make things much easier. For example
some places that checks for "SER_RS485_ENABLED" won't need to be rewritten.
Signed-off-by: Crescent CY Hsieh <crescentcy.hsieh@moxa.com>
Link: https://lore.kernel.org/r/20231201071554.258607-3-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename the variable size to temp and change its data type from
unsigned int to u64 to avoid type casting in multiplication. Remove the
intermediate variable frame_time and use temp instead to accommodate
the nanoseconds(ns). port->frame_time is an unsigned int, therefore an
explicit cast is used to improve readability. Having said this unsigned
int is sufficinet to hold frame time duration in nanoseconds for all
the standard baudrates.
Consider 9600 baud, it takes 1/9600 seconds for one bit, for a total of
10 bits (start, 8-bit data, stop) 10/9600=1.04 ms for 1 byte transfer,
frame_time here is 1041667ns. As baudrate increases frame_time
decreases, say for 115200 baud it is 86806ns.
To avoid costly 64-bit arithmetic we do not upconvert the type for
variable frame_time as overflow happens for extremely low baudrates
which are impractical and are not used in real-world applications.
Signed-off-by: Vamshi Gajjela <vamshigajjela@google.com>
Link: https://lore.kernel.org/r/20231109063417.3971005-3-vamshigajjela@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MOXA PCIe RS422/RS485 boards will not function by default because of the
initial default serial interface of all MOXA PCIe boards is set to
RS232.
This patch fixes the problem above by setting the initial default serial
interface to RS422 for those MOXA RS422/RS485 PCIe boards.
Signed-off-by: Crescent CY Hsieh <crescentcy.hsieh@moxa.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20231214060234.6147-1-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On this platform, different vendor data is used. That requires a
compile-time check as we access (1) a global boolean & (2) our local
vendor data. Both symbols are accessible only when
CONFIG_ACPI_SPCR_TABLE is enabled.
Factor the vendor data overriding to a separate function that is empty
when CONFIG_ACPI_SPCR_TABLE is not defined.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231207-mbly-uart-v6-8-e384afa5e78c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The whole function body is encapsulated inside an if-condition. Reverse
the if logic and early return to remove one indentation level.
Also turn two nested ifs into a single one at the end of the function.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231207-mbly-uart-v6-7-e384afa5e78c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following messages from checkpatch:
$ ./scripts/checkpatch.pl --strict --file \
drivers/tty/serial/amba-pl011.c
ERROR: do not initialise statics to false
WARNING: Possible unnecessary 'out of memory' message
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Prefer [subsystem eg: netdev]_info([subsystem]dev, ... then
dev_info(dev, ... then pr_info(... to
CHECK: Prefer using the BIT macro
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231207-mbly-uart-v6-6-e384afa5e78c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following checkpatch warnings & checks:
$ ./scripts/checkpatch.pl --strict --file \
drivers/tty/serial/amba-pl011.c
CHECK: Unbalanced braces around else statement
CHECK: Unnecessary parentheses around '[...]'
CHECK: braces {} should be used on all arms of this statement
CHECK: Comparison to NULL could be written "[...]"
WARNING: Comparisons should place the constant on the right side of the test
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231207-mbly-uart-v6-5-e384afa5e78c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses two TIOCMBIT macros inside pl011_{get,set}_mctrl to
simplify the logic. Those look scary to checkpatch because they contain
ifs without do-while loops.
Avoid the macros by creating small equivalent static functions; that
lets the compiler do its type checking & avoids checkpatch errors.
For the second instance __assign_bit is not usable because it deals with
unsigned long pointers whereas we have an unsigned int in
pl011_set_mctrl.
This addresses the following checkpatch warnings:
$ ./scripts/checkpatch.pl --strict --file \
drivers/tty/serial/amba-pl011.c
ERROR: Macros starting with if should be enclosed by a do -
while loop to avoid possible if/else logic defects
CHECK: Macro argument 'uartbit' may be better as '(uartbit)' to
avoid precedence issues
ERROR: Macros starting with if should be enclosed by a do - while
loop to avoid possible if/else logic defects
CHECK: Macro argument 'tiocmbit' may be better as '(tiocmbit)' to
avoid precedence issues
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231207-mbly-uart-v6-3-e384afa5e78c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow recommandations from:
$ ./scripts/checkpatch.pl --strict --file \
drivers/tty/serial/amba-pl011.c
We fix 5 warnings and 48 checks, all related to whitespace.
Culprits are:
CHECK: Alignment should match open parenthesis
CHECK: Blank lines aren't necessary after an open brace '{'
CHECK: Lines should not end with a '('
CHECK: Please don't use multiple blank lines
CHECK: Please use a blank line after function/struct/union/enum
declarations
CHECK: spaces preferred around that '/' (ctx:VxV)
CHECK: spaces preferred around that '|' (ctx:VxV)
WARNING: Missing a blank line after declarations
WARNING: please, no spaces at the start of a line
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20231207-mbly-uart-v6-2-e384afa5e78c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It can happen that while a break is received the transmitter gets empty
and IIR signals a Transmitter holding register empty (THRI) event. In
this case it's too early for the break workaround. Still doing it then
results in the THRI event not being rereported which makes the driver
miss that and e.g. for RS485 half-duplex communication it fails to
switch back to RX mode.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231213174312.2341013-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cc4c1d05eb ("sc16is7xx: Properly resume TX after stop") changed
behavior to unconditionnaly set the THRI interrupt in sc16is7xx_tx_proc().
For example when sending a 65 bytes message, and assuming the Tx FIFO is
initially empty, sc16is7xx_handle_tx() will write the first 64 bytes of the
message to the FIFO and sc16is7xx_tx_proc() will then activate THRI. When
the THRI IRQ is fired, the driver will write the remaining byte of the
message to the FIFO, and disable THRI by calling sc16is7xx_stop_tx().
When sending a 2 bytes message, sc16is7xx_handle_tx() will write the 2
bytes of the message to the FIFO and call sc16is7xx_stop_tx(), disabling
THRI. After sc16is7xx_handle_tx() exits, control returns to
sc16is7xx_tx_proc() which will unconditionally set THRI. When the THRI IRQ
is fired, the driver simply acknowledges the interrupt and does nothing
more, since all the data has already been written to the FIFO. This results
in 2 register writes and 4 register reads all for nothing and taking
precious cycles from the I2C/SPI bus.
Fix this by enabling the THRI interrupt only when we fill the Tx FIFO to
its maximum capacity and there are remaining bytes to send in the message.
Fixes: cc4c1d05eb ("sc16is7xx: Properly resume TX after stop")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231211171353.2901416-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SC16IS7XX IC supports a burst mode to access the FIFOs where the
initial register address is sent ($00), followed by all the FIFO data
without having to resend the register address each time. In this mode, the
IC doesn't increment the register address for each R/W byte.
The regmap_raw_read() and regmap_raw_write() are functions which can
perform IO over multiple registers. They are currently used to read/write
from/to the FIFO, and although they operate correctly in this burst mode on
the SPI bus, they would corrupt the regmap cache if it was not disabled
manually. The reason is that when the R/W size is more than 1 byte, these
functions assume that the register address is incremented and handle the
cache accordingly.
Convert FIFO R/W functions to use the regmap _noinc_ versions in order to
remove the manual cache control which was a workaround when using the
_raw_ versions. FIFO registers are properly declared as volatile so
cache will not be used/updated for FIFO accesses.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231211171353.2901416-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver has been converted to use one regmap per port, change
efr locking to operate on a channel basis instead of on the whole IC.
Fixes: 3837a03795 ("serial: sc16is7xx: improve regmap debugfs by using one regmap per port")
Cc: <stable@vger.kernel.org> # 6.1.x: 3837a03 serial: sc16is7xx: improve regmap debugfs by using one regmap per port
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231211171353.2901416-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver has been converted to use one regmap per port, the line
structure member is no longer used, so remove it.
Fixes: 3837a03795 ("serial: sc16is7xx: improve regmap debugfs by using one regmap per port")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231211171353.2901416-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove global struct regmap so that it is more obvious that this
regmap is to be used only in the probe function.
Also add a comment to that effect in probe function.
Fixes: 3837a03795 ("serial: sc16is7xx: improve regmap debugfs by using one regmap per port")
Cc: <stable@vger.kernel.org>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231211171353.2901416-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using a static buffer inside sc16is7xx_regmap_name() was a convenient and
simple way to set the regmap name without having to allocate and free a
buffer each time it is called. The drawback is that the static buffer
wastes memory for nothing once regmap is fully initialized.
Remove static buffer and use constant strings instead.
This also avoids a truncation warning when using "%d" or "%u" in snprintf
which was flagged by kernel test robot.
Fixes: 3837a03795 ("serial: sc16is7xx: improve regmap debugfs by using one regmap per port")
Cc: <stable@vger.kernel.org> # 6.1.x: 3837a03 serial: sc16is7xx: improve regmap debugfs by using one regmap per port
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231211171353.2901416-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Error checking for matching was not necessary as matching is always
successful if we're already in probe and the match tables always have data
pointers.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231207162632.2650356-2-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. Soon the implicit includes are going to be removed.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231207162632.2650356-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial driver data for Google Tensor gs101 SoC and a common
fifoszdt_serial_drv_data that can be used by platforms that specify the
samsung,uart-fifosize DT property.
A corresponding dt-bindings patch updates the yaml to ensure
samsung,uart-fifosize is a required property.
Tested-by: Will McVicker <willmcvicker@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20231211162331.435900-14-peter.griffin@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
tty_operations::send_xchar is one of the last users of 'char' type for
characters in the tty layer. Convert it to u8 now.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-bluetooth@vger.kernel.org
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20231206073712.17776-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parse the OPP table from the device tree and use dev_pm_opp_set_rate()
instead of clk_set_rate() to allow making performance state votes
specified in the OPP table (e.g. for power domains and interconnects).
Without an OPP table in the device tree this will behave just as before
this patch.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Link: https://lore.kernel.org/r/20231128-serial-msm-dvfs-v1-2-4f290d20a4be@kernkonzept.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the serial port as RS485 port, the tx statemachine is used to
control the RTS pin to drive the RS485 transceiver TX_EN pin. When the
TTY port is closed in the middle of a transmission (for instance during
userland application crash), imx_uart_shutdown disables the interface
and disables the Transmission Complete interrupt. afer that,
imx_uart_stop_tx bails on an incomplete transmission, to be retriggered
by the TC interrupt. This interrupt is disabled and therefore the tx
statemachine never transitions out of SEND. The statemachine is in
deadlock now, and the TX_EN remains low, making the interface useless.
imx_uart_stop_tx now checks for incomplete transmission AND whether TC
interrupts are enabled before bailing to be retriggered. This makes sure
the state machine handling is reached, and is properly set to
WAIT_AFTER_SEND.
Fixes: cb1a609236 ("serial: imx: implement rts delaying for rs485")
Signed-off-by: Paul Geurts <paul_geurts@live.nl>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Eberhard Stoll <eberhard.stoll@gmx.de>
Link: https://lore.kernel.org/r/AM0PR09MB26758F651BC1B742EB45775995B8A@AM0PR09MB2675.eurprd09.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Granite Rapids-D has an additional UART that is enumerated via ACPI.
Add ACPI ID for it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20231205195524.2705965-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console is immediately assigned to the ma35d1 port without
checking its index. This oversight can lead to out-of-bounds
errors when the index falls outside the valid '0' to
MA35_UART_NR range. Such scenario trigges ran error like the
following:
UBSAN: array-index-out-of-bounds in drivers/tty/serial/ma35d1_serial.c:555:51
index -1 is out of range for type 'uart_ma35d1_port [17]
Check the index before using it and bail out with a warning.
Fixes: 930cbf92db ("tty: serial: Add Nuvoton ma35d1 serial driver support")
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Cc: Jacky Huang <ychuang3@nuvoton.com>
Cc: <stable@vger.kernel.org> # v6.5+
Link: https://lore.kernel.org/r/20231204163804.1331415-2-andi.shyti@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Designware UART has an optional feature to enable Fractional Baud Rate
Divisor (DLF) through the FRACTIONAL_BAUD_DIVISOR_EN configuration
parameter, and it is not dependent on ADDITIONAL_FEATURES.
dw8250_setup_port() checks DLF to determine dlf_size only when UART
Component Version (UCV) is non-zero. As mentioned above DLF and UCV are
independent features. Move the logic corresponding to DLF size
calculation ahead of the UCV check to prevent early return. Otherwise,
dlf_size will be zero and driver will not be able to use the
controller's fractional baud rate divisor (DLF) feature.
Signed-off-by: Vamshi Gajjela <vamshigajjela@google.com>
Link: https://lore.kernel.org/r/20231126160420.2442330-1-vamshigajjela@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment wording can be confusing, as txlen will return the number of
bytes available in the FIFO, which can be less than the maximum theoretical
Tx FIFO size.
Change the comment so that it is unambiguous.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231122175957.3875102-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment wording can be confusing, as txlen will return the number of
bytes available in the FIFO, which can be less than the maximum theoretical
Tx FIFO size.
Change the comment so that it is unambiguous.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231122175859.3874753-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 81a61051e0.
With tty and serdev controller moved to be children of the serial core
port device, runtime PM usage count of the serdev controller now
propagates to the serial hardware controller parent device as expected.
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231113080758.30346-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's move tty and serdev controller to be children of the serial core port
device. This way the runtime PM usage count of a child device propagates
to the serial hardware device.
The tty and serdev devices are associated with a specific serial port of
a serial hardware controller device, and we now have serial core hierarchy
of controllers and ports.
The tty device moves happily with just a change of the parent device and
update of device_find_child() handling. The serdev device init needs some
changes to separate the serial hardware controller device from the parent
device.
With this change the tty devices move under sysfs similar to this x86_64
qemu example of a diff of "find /sys -name ttyS*":
/sys/class/tty/ttyS0
/sys/class/tty/ttyS3
/sys/class/tty/ttyS1
-/sys/devices/pnp0/00:04/tty/ttyS0
-/sys/devices/platform/serial8250/tty/ttyS2
-/sys/devices/platform/serial8250/tty/ttyS3
-/sys/devices/platform/serial8250/tty/ttyS1
+/sys/devices/pnp0/00:04/00:04:0/00:04:0.0/tty/ttyS0
+/sys/devices/platform/serial8250/serial8250:0/serial8250:0.3/tty/ttyS3
+/sys/devices/platform/serial8250/serial8250:0/serial8250:0.1/tty/ttyS1
+/sys/devices/platform/serial8250/serial8250:0/serial8250:0.2/tty/ttyS2
If a serdev device is used instead of a tty, it moves in a similar way.
Suggested-by: Johan Hovold <johan@kernel.org>
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231113080758.30346-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device number 204 has a range of minors on major number.
uart_register_driver is failing due to lack of minor numbers
when more number of uart ports used. So, to avoid minor number
limitation on 204 major number use dynamic major allocation
when more than 4 uart ports used otherwise use static major
allocation.
https://docs.kernel.org/arch/arm/sa1100/serial_uart.html
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Link: https://lore.kernel.org/r/20231116134003.3762725-3-manikanta.guntupalli@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the driver was converted to use .remove_new() the return function
doesn't return a value any more. So remove the obsolete documentation
about the return value.
Reported-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20231117101236.878008-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there is no guarantee that the memory returned by
dma_alloc_coherent() is associated with a 'struct page', using the
architecture specific phys_to_page() is wrong, but using
virt_to_page() would be as well.
Stop using sg lists altogether and just use the *_single() functions
instead. This also simplifies the code a bit since the scatterlists in
this driver always have only one entry anyway.
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
gc: Add a commit log from the initial thread:
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
Fixes: cb06ff102e ("ARM: PL011: Add support for Rx DMA buffer polling.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20231122171503.235649-1-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device has a silicon bug that makes it report a timeout interrupt
but no data in the FIFO.
The datasheet states the following in the errata section 18.1.4:
"If the host reads the receive FIFO at the same time as a
time-out interrupt condition happens, the host might read 0xCC
(time-out) in the Interrupt Indication Register (IIR), but bit 0
of the Line Status Register (LSR) is not set (means there is no
data in the receive FIFO)."
The errata description seems to indicate it concerns only polled mode of
operation when reading bit 0 of the LSR register. However, tests have
shown and NXP has confirmed that the RXLVL register also yields 0 when
the bug is triggered, and hence the IRQ driven implementation in this
driver is equally affected.
This bug has hit us on production units and when it does, sc16is7xx_irq()
would spin forever because sc16is7xx_port_irq() keeps seeing an
interrupt in the IIR register that is not cleared because the driver
does not call into sc16is7xx_handle_rx() unless the RXLVL register
reports at least one byte in the FIFO.
Fix this by always reading one byte from the FIFO when this condition
is detected in order to clear the interrupt. This approach was
confirmed to be correct by NXP through their support channels.
Tested by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Co-Developed-by: Maxim Popov <maxim.snafu@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231123072818.1394539-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes commit 439c7183e5 ("serial: 8250: 8250_omap: Disable RX
interrupt after DMA enable") which unfortunately set the
UART_HAS_RHR_IT_DIS bit in the UART_OMAP_IER2 register and never
cleared it.
Cc: stable@vger.kernel.org
Fixes: 439c7183e5 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231031110909.11695-1-rwahl@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there is no support for earlycon on the AM654 UART
controller. This commit adds it.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231031131242.15516-1-rwahl@gmx.de
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting RX DMA on THRI interrupt is too early because TX may not have
finished yet.
This change is inspired by commit 90b8596ac4 ("serial: 8250: Prevent
starting up DMA Rx on THRI interrupt") and fixes DMA issues I had with
an AM62 SoC that is using the 8250 OMAP variant.
Cc: stable@vger.kernel.org
Fixes: c26389f998 ("serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs")
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231101171431.16495-1-rwahl@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this current driver regmap implementation, it is hard to make sense
of the register addresses displayed using the regmap debugfs interface,
because they do not correspond to the actual register addresses documented
in the datasheet. For example, register 1 is displayed as registers 04 thru
07:
$ cat /sys/kernel/debug/regmap/spi0.0/registers
04: 10 -> Port 0, register offset 1
05: 10 -> Port 1, register offset 1
06: 00 -> Port 2, register offset 1 -> invalid
07: 00 -> port 3, register offset 1 -> invalid
...
The reason is that bits 0 and 1 of the register address correspond to the
channel (port) bits, so the register address itself starts at bit 2, and we
must 'mentally' shift each register address by 2 bits to get its real
address/offset.
Also, only channels 0 and 1 are supported by the chip, so channel mask
combinations of 10b and 11b are invalid, and the display of these
registers is useless.
This patch adds a separate regmap configuration for each port, similar to
what is done in the max310x driver, so that register addresses displayed
match the register addresses in the chip datasheet. Also, each port now has
its own debugfs entry.
Example with new regmap implementation:
$ cat /sys/kernel/debug/regmap/spi0.0-port0/registers
1: 10
2: 01
3: 00
...
$ cat /sys/kernel/debug/regmap/spi0.0-port1/registers
1: 10
2: 01
3: 00
As an added bonus, this also simplifies some operations (read/write/modify)
because it is no longer necessary to manually shift register addresses.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231030211447.974779-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use @ and - to conform with kernel-doc style.
Reported-by: kernel test robot <yujie.liu@intel.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Link: https://lore.kernel.org/r/20231106152428.3641883-1-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clang-struct [1] found struct serial_cfg_mem's members unused.
In fact, the whole structure is unused since commit 6ae3b84d97
("serial_cs: use pcmcia_loop_config() and pre-determined values"). Drop
it completely.
[1] https://github.com/jirislaby/clang-struct
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20231121103626.17772-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clang-struct [1] found rp2_uart_port::ignore_rx unused.
It was actually never used. Not even in introductory commit 7d9f49afa4
("serial: rp2: New driver for Comtrol RocketPort 2 cards").
[1] https://github.com/jirislaby/clang-struct
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20231121103626.17772-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clang-struct [1] found jsm_board::type and ::jsm_board_entry unused.
::jsm_board_entry is unused since 614a7d6a76 ("fix up newly added jsm driver")
::type was never used as far as I can tell. Even when the driver was
introduced in the pre-git era.
Remove them both.
[1] https://github.com/jirislaby/clang-struct
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20231121103626.17772-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clang-struct [1] found board_ops::get_uart_bytes_left() and
::send_immediate_char() unused.
Both are only set but never called. And it has been like that since the
git history, so drop both the members along with the cls+neo
implementations.
[1] https://github.com/jirislaby/clang-struct
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20231121103626.17772-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-53-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-52-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-51-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-50-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-49-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-48-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-47-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-46-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-45-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-44-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-43-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-42-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20231110152927.70601-41-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20231110152927.70601-40-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231110152927.70601-39-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-38-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-37-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-36-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231110152927.70601-35-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-34-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-33-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-32-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-31-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-30-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-29-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-28-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-27-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-26-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-25-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-24-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-23-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-22-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-21-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20231110152927.70601-20-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-18-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-17-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-16-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-15-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-14-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231110152927.70601-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20231110152927.70601-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20231110152927.70601-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20231110152927.70601-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> # 8250_bcm*
Link: https://lore.kernel.org/r/20231110152927.70601-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Returning an error code from .remove() makes the driver core emit the
little helpful error message:
remove callback returned a non-zero value. This will be ignored.
and then remove the device anyhow.
So replace the error return (and with it the little helpful error
message) by a more useful error message.
Fixes: 31815c08fc ("serial: sccnxp: Replace pdata.init/exit with regulator API")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231110152927.70601-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Returning an error code from .remove() makes the driver core emit the
little helpful error message:
remove callback returned a non-zero value. This will be ignored.
and then remove the device anyhow. So all resources that were not freed
are leaked in this case. Skipping serial8250_unregister_port() has the
potential to keep enough of the UART around to trigger a use-after-free.
So replace the error return (and with it the little helpful error
message) by a more useful error message and continue to cleanup.
Fixes: e3f0c638f4 ("serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231110152927.70601-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----
iQJOBAABCAA4FiEEbt46xwy6kEcDOXoUeZbBVTGwZHAFAmVMnfAaHHRzYm9nZW5k
QGFscGhhLmZyYW5rZW4uZGUACgkQeZbBVTGwZHAnjBAAnz/uhqqZy1aU1Fna1Fr8
AqR3AeA3DfKGpZXY1HttgmZhd6nzktmek5hT1007eEWieYOuR32fin0XflL8KfrA
ecPva7WD3FMJRc56yQ1SI836kLKDuAVW+m6AvzqvWron1IyAScUjTtrjmY9ZxLh1
citiMwh8eHK1nT2voBQKzCKoXXsZO+yqvnVNWnGiRRjmYHk9Gpu6kcM5sw5xQWhP
jCA+stWY2VQdeTRrNA4pAgqoD0q4RA0Ntzdb8cZGFiFBxdmOlAl6P4t5WusP2shN
eIc4uEykWc1utkay4+o+c9dsABiaYPSQvuuVQrx7uFWSL7zEup5TUw46zN9ptxsh
CRLEKeJtaJvuUC4WdJRCAB6n7lAjfRtdsALlWv1gU0DWFdJbspv8YExZmBZhqgDM
8LkII39Hvi3oQYAjM9W+/FsPP3BNvIpS07c3hlcuSvbo3cHNzHL6wfNDpPV0TN3L
P30LZWybQj+lr2amw38r4zOh5nuz+9eyP7mes8cgorlMfjxv0vIMcg3XT1D3+YJK
7lLKmoHgBab6VNUeUPS92cfCNlb50TQeSMf21Xt/obrhpVGJnLHQ50jg8NaKENyc
gwLyvjbf/hIbgJAvKnaRGEcV8COwppcX+U3yEAbXJ2eAvYEXZCU41dH5x3/7WRuB
tvlRfkDcu9ddjyQDtZ4yv/M=
=g+6E
-----END PGP SIGNATURE-----
Merge tag 'mips_6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- removed AR7 platform support
- cleanups and fixes
* tag 'mips_6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: AR7: remove platform
watchdog: ar7_wdt: remove driver to prepare for platform removal
vlynq: remove bus driver
mtd: parsers: ar7: remove support
serial: 8250: remove AR7 support
arch: mips: remove ReiserFS from defconfig
MIPS: lantiq: Remove unnecessary include of <linux/of_irq.h>
MIPS: lantiq: Fix pcibios_plat_dev_init() "no previous prototype" warning
MIPS: KVM: Fix a build warning about variable set but not used
MIPS: Remove dead code in relocate_new_kernel
mips: dts: ralink: mt7621: rename to GnuBee GB-PC1 and GnuBee GB-PC2
mips: dts: ralink: mt7621: define each reset as an item
mips: dts: ingenic: Remove unneeded probe-type properties
MIPS: loongson32: Remove dma.h and nand.h
Here is the big set of tty/serial driver changes for 6.7-rc1. Included
in here are:
- console/vgacon cleanups and removals from Arnd
- tty core and n_tty cleanups from Jiri
- lots of 8250 driver updates and cleanups
- sc16is7xx serial driver updates
- dt binding updates
- first set of port lock wrapers from Thomas for the printk fixes
coming in future releases
- other small serial and tty core cleanups and updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZUTbaw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk9+gCeKdoRb8FDwGCO/GaoHwR4EzwQXhQAoKXZRmN5
LTtw9sbfGIiBdOTtgLPb
=6PJr
-----END PGP SIGNATURE-----
Merge tag 'tty-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial updates from Greg KH:
"Here is the big set of tty/serial driver changes for 6.7-rc1. Included
in here are:
- console/vgacon cleanups and removals from Arnd
- tty core and n_tty cleanups from Jiri
- lots of 8250 driver updates and cleanups
- sc16is7xx serial driver updates
- dt binding updates
- first set of port lock wrapers from Thomas for the printk fixes
coming in future releases
- other small serial and tty core cleanups and updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (193 commits)
serdev: Replace custom code with device_match_acpi_handle()
serdev: Simplify devm_serdev_device_open() function
serdev: Make use of device_set_node()
tty: n_gsm: add copyright Siemens Mobility GmbH
tty: n_gsm: fix race condition in status line change on dead connections
serial: core: Fix runtime PM handling for pending tx
vgacon: fix mips/sibyte build regression
dt-bindings: serial: drop unsupported samsung bindings
tty: serial: samsung: drop earlycon support for unsupported platforms
tty: 8250: Add note for PX-835
tty: 8250: Fix IS-200 PCI ID comment
tty: 8250: Add Brainboxes Oxford Semiconductor-based quirks
tty: 8250: Add support for Intashield IX cards
tty: 8250: Add support for additional Brainboxes PX cards
tty: 8250: Fix up PX-803/PX-857
tty: 8250: Fix port count of PX-257
tty: 8250: Add support for Intashield IS-100
tty: 8250: Add support for Brainboxes UP cards
tty: 8250: Add support for additional Brainboxes UC cards
tty: 8250: Remove UC-257 and UC-431
...
The ia64 architecture gets its well-earned retirement as planned,
now that there is one last (mostly) working release that will
be maintained as an LTS kernel.
The architecture specific system call tables are updated for
the added map_shadow_stack() syscall and to remove references
to the long-gone sys_lookup_dcookie() syscall.
-----BEGIN PGP SIGNATURE-----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=H1vH
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull ia64 removal and asm-generic updates from Arnd Bergmann:
- The ia64 architecture gets its well-earned retirement as planned,
now that there is one last (mostly) working release that will be
maintained as an LTS kernel.
- The architecture specific system call tables are updated for the
added map_shadow_stack() syscall and to remove references to the
long-gone sys_lookup_dcookie() syscall.
* tag 'asm-generic-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
hexagon: Remove unusable symbols from the ptrace.h uapi
asm-generic: Fix spelling of architecture
arch: Reserve map_shadow_stack() syscall number for all architectures
syscalls: Cleanup references to sys_lookup_dcookie()
Documentation: Drop or replace remaining mentions of IA64
lib/raid6: Drop IA64 support
Documentation: Drop IA64 from feature descriptions
kernel: Drop IA64 support from sig_fault handlers
arch: Remove Itanium (IA-64) architecture
Richard reported that a serial port may end up sometimes with tx data
pending in the buffer for long periods of time.
Turns out we bail out early on any errors from pm_runtime_get(),
including -EINPROGRESS. To fix the issue, we need to ignore -EINPROGRESS
as we only care about the runtime PM usage count at this point. We check
for an active runtime PM state later on for tx.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Cc: stable <stable@kernel.org>
Reported-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Cc: Bruce Ashfield <bruce.ashfield@gmail.com>
Cc: Mikko Rapeli <mikko.rapeli@linaro.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Randy MacLeod <randy.macleod@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231023074856.61896-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1ea35b3557 ("ARM: s3c: remove s3c24xx specific hacks") removed
support here for several old platforms, but kept support for earlycon
for those same platforms.
As earlycon support for otherwise unsupported platforms doesn't seem to
be useful, just drop it as well.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20231019100639.4026283-1-andre.draszik@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the PCI comment for the IS-200 card. The PCI ID for the IS-200
is 0x0d80, and the definition used (PCI_DEVICE_ID_INTASHIELD_IS200)
is indeed 0x0d80, clarify that by fixing the comment as its
neighbouring cards are all at 0x0020 offsets.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB78993B6AD85F6550AF6590FBC4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the later revisions of the Brainboxes PX cards are based
on the Oxford Semiconductor chipset. Due to the chip's unique setup
these cards need to be initialised.
Previously these were tested against a reference card with the same broken
baudrate on another PC, cancelling out the effect. With this patch they
work and can transfer/receive find against an FTDI-based device.
Add all of the cards which require this setup to the quirks table.
Thanks to Maciej W. Rozycki for clarification on this chip.
Fixes: ef5a03a26c ("tty: 8250: Add support for Brainboxes PX cards.")
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB7899D222A4AB2A4E8C57108FC4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UC-257 is a serial + LPT card, so remove it from this driver.
A patch has been submitted to add it to parport_serial instead.
Additionaly, the UC-431 does not use this card ID, only the UC-420
does. The 431 is a 3-port card and there is no generic 3-port configuration
available, so remove reference to it from this driver.
Fixes: 152d1afa83 ("tty: Add support for Brainboxes UC cards.")
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB78995ADF7394C74AD4CF3357C4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the console suspend is disabled, the genpd of the console shall not
be powered-off during suspend.
Set the flag GENPD_FLAG_ALWAYS_ON to the corresponding genpd during
suspend, and restore the original value during the resume.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20231017130540.1149721-1-thomas.richard@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move PCI_DEVICE_ID macros to the top so that these macros can be used
throughout 8250_pci.c
Signed-off-by: Crescent CY Hsieh <crescentcy.hsieh@moxa.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20231018091739.10125-4-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When support for various old platforms was removed in commit
1ea35b3557 ("ARM: s3c: remove s3c24xx specific hacks"),
s3c24xx_serial_ops also became unused here because nothing sets port
type TYPE_S3C24XX anymore.
Remove s3c24xx_serial_ops and all the code that's unreachable now.
Fixes: 1ea35b3557 ("ARM: s3c: remove s3c24xx specific hacks")
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20231019100901.4026680-1-andre.draszik@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
esp32s3 variant of the esp32 UART has limited baudrate divisor range
that does not allow it to use 9600 and lower rates with 40MHz input
clock. Use clock prescaler present in this UART variant to help with
that.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20231018191252.1551972-1-jcmvbkbc@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AR7 is going to be removed from the Kernel, so remove its type
definition from 8250 code. As with previous removals, I checked with
Debian Code Search that 'PORT_AR7' is not used in userspace.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
uart_get_baud_rate has input parameters 'min' and 'max' limiting the
range of acceptable baud rates from the caller's perspective. If neither
current or old termios structures have acceptable baud rate setting and
9600 is not in the min/max range either the function returns 0 and
issues a warning.
However for a UART that does not support speed of 9600 baud this is
expected behavior.
Clarify that 0 can be (and always could be) returned from the
uart_get_baud_rate. Don't issue a warning in that case.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20231010085926.1021667-2-jcmvbkbc@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zynq UG585 states, in chapter B.33, for XUARTPS_CR_STARTBRK:
It can only be set if STPBRK (Stop transmitter break) is not high
This fixes tcsendbreak, which otherwise does not actually break.
Signed-Off-By: Julien Malik <julien.malik@unseenlabs.fr>
Link: https://lore.kernel.org/r/20230624210323.88455-1-julien.malik@unseenlabs.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the tty/serial fixes in here as well for testing, and this
resolves merge conflicts in:
drivers/tty/serial/serial_core.c
as reported in linux-next
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new Amlogic S4 SoC does not have a always-on uart, so add
OF_EARLYCON_DECLARE for it.
Amlogic T7 will use this as fallback.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231009121151.4509-1-tanure@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maximilian reported that surface_serial_hub serdev tx does not work during
system suspend. During system suspend, runtime PM gets disabled in
__device_suspend_late(), and tx is unable to wake-up the serial core port
device that we use to check if tx is safe to start. Johan summarized the
regression noting that serdev tx no longer always works as earlier when the
serdev device is runtime PM active.
The serdev device and the serial core controller devices are siblings of
the serial port hardware device. The runtime PM usage count from serdev
device does not propagate to the serial core device siblings, it only
propagates to the parent.
In addition to the tx issue for suspend, testing for the serial core port
device can cause an unnecessary delay in enabling tx while waiting for the
serial core port device to wake-up. The serial core port device wake-up is
only needed to flush pending tx when the serial port hardware device was
in runtime PM suspended state.
To fix the regression, we need to check the runtime PM state of the parent
serial port hardware device for tx instead of the serial core port device.
As the serial port device drivers may or may not implement runtime PM, we
need to also add a check for pm_runtime_enabled().
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: stable <stable@kernel.org>
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231005075644.25936-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this check ever triggers
static int uart_get_info(struct tty_port *port, struct serial_struct *retinfo)
{
uport = uart_port_check(state);
if (!uport)
goto out;
then all those sysfs users will print stack contents to userspace.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Link: https://lore.kernel.org/r/967b9ef1-fb36-48bf-9e6a-1b99af24c052@p183
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify uart_get_rs485_mode() by using temporary variable for
the GPIO descriptor. With that, use proper type for the flags
of the GPIO descriptor.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231003142346.3072929-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's drop the use of pm_runtime_irq_safe() for 8250_omap. The use of
pm_runtime_irq_safe() is not nice as it takes a permanent usage count on
the parent device.
We can finally drop pm_runtime_irq_safe() safely as the kernel now knows
when the uart port tx is active. This changed with commit 84a9582fd2
("serial: core: Start managing serial controllers to enable runtime PM").
For serial port rx, we already use Linux generic wakeirqs for 8250_omap.
To drop pm_runtime_irq_safe(), we need to add handling for shallow idle
state where the port hardware may already be awake and an IO interrupt
happens. We also need to replace the serial8250_rpm sync calls in the
interrupt handlers with async runtime PM calls.
Note that omap8250_irq() calls omap_8250_dma_handle_irq(), so we don't
need separate runtime PM calls in omap_8250_dma_handle_irq().
While at it, let's also add the missing line break to the end of
omap8250_runtime_resume() to group the calls.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231004062650.64487-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We now get errors on system suspend if no_console_suspend is set as
reported by Thomas. The errors started with commit 20a41a6261 ("serial:
8250_omap: Use force_suspend and resume for system suspend").
Let's fix the issue by checking for console_suspend_enabled in the system
suspend and resume path.
Note that with this fix the checks for console_suspend_enabled in
omap8250_runtime_suspend() become useless. We now keep runtime PM usage
count for an attached kernel console starting with commit bedb404e91
("serial: 8250_port: Don't use power management for kernel console").
Fixes: 20a41a6261 ("serial: 8250_omap: Use force_suspend and resume for system suspend")
Cc: stable <stable@kernel.org>
Cc: Udit Kumar <u-kumar1@ti.com>
Reported-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230926061319.15140-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 44b27aec9d ("serial: core, 8250: set RS485 termination GPIO in
serial core") enabled support for RS485 termination GPIOs behind i2c
expanders by setting the GPIO outside of the critical section protected
by the port spinlock. Access to the i2c expander may sleep, which
caused a splat with the port spinlock held.
Commit 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in
driver-specific way") erroneously regressed that by spinlocking the
GPIO manipulation again.
Fix by moving uart_rs485_config() (the function manipulating the GPIO)
outside of the spinlocked section and acquiring the spinlock inside of
uart_rs485_config() for the invocation of ->rs485_config() only.
This gets us one step closer to pushing the spinlock down into the
->rs485_config() callbacks which actually need it. (Some callbacks
do not want to be spinlocked because they perform sleepable register
accesses, see e.g. sc16is7xx_config_rs485().)
Stack trace for posterity:
Voluntary context switch within RCU read-side critical section!
WARNING: CPU: 0 PID: 56 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch
Call trace:
rcu_note_context_switch
__schedule
schedule
schedule_timeout
wait_for_completion_timeout
bcm2835_i2c_xfer
__i2c_transfer
i2c_transfer
i2c_transfer_buffer_flags
regmap_i2c_write
_regmap_raw_write_impl
_regmap_bus_raw_write
_regmap_write
_regmap_update_bits
regmap_update_bits_base
pca953x_gpio_set_value
gpiod_set_raw_value_commit
gpiod_set_value_nocheck
gpiod_set_value_cansleep
uart_rs485_config
uart_add_one_port
pl011_register_port
pl011_probe
Fixes: 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Suggested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.1+
Link: https://lore.kernel.org/r/f3a35967c28b32f3c6432d0aa5936e6a9908282d.1695307688.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert driver to be property provider agnostic and allow it to be
used on non-OF platforms.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230927160153.2717788-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many SoCs do not integrate DMA for the amba pl011 UART, causing
the following message on boot:
uart-pl011 80074000.serial: no DMA platform data
The UART still works in PIO, so better not to print such message that
may confuse people by causing them to think that there is something wrong
with the UART.
Change the message to debug level.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20230928145842.466933-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lockdep complains about possible circular locking dependencies when the
i.MX SDMA driver issues console messages under its spinlock. While the
SDMA driver calls back into the UART when issuing a message, the i.MX
UART driver will never call back into the SDMA driver for this UART,
because DMA is explicitly not used for UARTs providing the console.
To avoid the lockdep warnings put the UART port lock for console devices
into a separate subclass.
This fixes possible deadlock warnings like the following which was
provoked by adding a printk to the i.MX SDMA driver at a place where the
driver holds its spinlock.
======================================================
WARNING: possible circular locking dependency detected
6.6.0-rc3-00045-g517852be693b-dirty #110 Not tainted
------------------------------------------------------
swapper/0/0 is trying to acquire lock:
c1818e04 (console_owner){-...}-{0:0}, at: console_flush_all+0x1c4/0x634
but task is already holding lock:
c44649e0 (&vc->lock){-...}-{3:3}, at: sdma_int_handler+0xc4/0x368
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&vc->lock){-...}-{3:3}:
_raw_spin_lock_irqsave+0x4c/0x68
sdma_prep_dma_cyclic+0x1a8/0x21c
imx_uart_startup+0x44c/0x5d4
uart_startup+0x120/0x2b0
uart_port_activate+0x44/0x98
tty_port_open+0x80/0xd0
uart_open+0x18/0x20
tty_open+0x120/0x664
chrdev_open+0xc0/0x214
do_dentry_open+0x1d0/0x544
path_openat+0xbb0/0xea0
do_filp_open+0x5c/0xd4
do_sys_openat2+0xb8/0xf0
sys_openat+0x8c/0xd8
ret_fast_syscall+0x0/0x1c
-> #1 (&port_lock_key){-.-.}-{3:3}:
_raw_spin_lock_irqsave+0x4c/0x68
imx_uart_console_write+0x164/0x1a0
console_flush_all+0x220/0x634
console_unlock+0x64/0x164
vprintk_emit+0xb0/0x390
vprintk_default+0x24/0x2c
_printk+0x2c/0x5c
register_console+0x244/0x478
serial_core_register_port+0x5c4/0x618
imx_uart_probe+0x4e0/0x7d4
platform_probe+0x58/0xb0
really_probe+0xc4/0x2e0
__driver_probe_device+0x84/0x1a0
driver_probe_device+0x2c/0x108
__driver_attach+0x94/0x17c
bus_for_each_dev+0x7c/0xd0
bus_add_driver+0xc4/0x1cc
driver_register+0x7c/0x114
imx_uart_init+0x20/0x40
do_one_initcall+0x7c/0x3c4
kernel_init_freeable+0x17c/0x228
kernel_init+0x14/0x140
ret_from_fork+0x14/0x24
-> #0 (console_owner){-...}-{0:0}:
__lock_acquire+0x14b0/0x29a0
lock_acquire.part.0+0xb4/0x264
console_flush_all+0x20c/0x634
console_unlock+0x64/0x164
vprintk_emit+0xb0/0x390
vprintk_default+0x24/0x2c
_printk+0x2c/0x5c
sdma_int_handler+0xcc/0x368
__handle_irq_event_percpu+0x94/0x2d0
handle_irq_event+0x38/0xd0
handle_fasteoi_irq+0x98/0x248
handle_irq_desc+0x1c/0x2c
gic_handle_irq+0x6c/0x90
generic_handle_arch_irq+0x2c/0x64
__irq_svc+0x90/0xbc
cpuidle_enter_state+0x1a0/0x4f4
cpuidle_enter+0x30/0x40
do_idle+0x210/0x2b4
cpu_startup_entry+0x28/0x2c
rest_init+0xd0/0x184
arch_post_acpi_subsys_init+0x0/0x8
other info that might help us debug this:
Chain exists of:
console_owner --> &port_lock_key --> &vc->lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&vc->lock);
lock(&port_lock_key);
lock(&vc->lock);
lock(console_owner);
*** DEADLOCK ***
3 locks held by swapper/0/0:
#0: c44649e0 (&vc->lock){-...}-{3:3}, at: sdma_int_handler+0xc4/0x368
#1: c1818d50 (console_lock){+.+.}-{0:0}, at: vprintk_default+0x24/0x2c
#2: c1818d08 (console_srcu){....}-{0:0}, at: console_flush_all+0x44/0x634
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.6.0-rc3-00045-g517852be693b-dirty #110
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x60/0x90
dump_stack_lvl from check_noncircular+0x184/0x1b8
check_noncircular from __lock_acquire+0x14b0/0x29a0
__lock_acquire from lock_acquire.part.0+0xb4/0x264
lock_acquire.part.0 from console_flush_all+0x20c/0x634
console_flush_all from console_unlock+0x64/0x164
console_unlock from vprintk_emit+0xb0/0x390
vprintk_emit from vprintk_default+0x24/0x2c
vprintk_default from _printk+0x2c/0x5c
_printk from sdma_int_handler+0xcc/0x368
sdma_int_handler from __handle_irq_event_percpu+0x94/0x2d0
__handle_irq_event_percpu from handle_irq_event+0x38/0xd0
handle_irq_event from handle_fasteoi_irq+0x98/0x248
handle_fasteoi_irq from handle_irq_desc+0x1c/0x2c
handle_irq_desc from gic_handle_irq+0x6c/0x90
gic_handle_irq from generic_handle_arch_irq+0x2c/0x64
generic_handle_arch_irq from __irq_svc+0x90/0xbc
Exception stack(0xc1801ee8 to 0xc1801f30)
1ee0: ffffffff ffffffff 00000001 00030349 00000000 00000012
1f00: 00000000 d7e45f4b 00000012 00000000 d7e16d63 c1810828 00000000 c1801f38
1f20: c108125c c1081260 60010013 ffffffff
__irq_svc from cpuidle_enter_state+0x1a0/0x4f4
cpuidle_enter_state from cpuidle_enter+0x30/0x40
cpuidle_enter from do_idle+0x210/0x2b4
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from rest_init+0xd0/0x184
rest_init from arch_post_acpi_subsys_init+0x0/0x8
Reported-by: Tim van der Staaij <Tim.vanderstaaij@zigngroup.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20230928064320.711603-1-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct pci1xxxx_8250.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Cc: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922175242.work.442-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sealevel XR17V35X based cards utilize DTR to control RS-485 Enable, but
the current implementation of 8250_exar uses RTS for the auto-RS485-Enable
mode of the XR17V35X UARTs. This patch implements DTR Auto-RS485 on
Sealevel cards.
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenkoa@linux.intel.com>
Link: https://lore.kernel.org/r/4b8ad8ab6728742464c4e048fdeecb2b40522aef.camel@sealevel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_clk_get_optional_enabled() to simplify the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230919195513.3197930-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the error messages format unified by switching to use
dev_err_probe() where it makes sense.
This also helps simplifing the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230918103648.1185663-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-75-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-74-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-73-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-72-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-71-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-70-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-69-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-68-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-67-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-66-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-65-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-64-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-63-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-62-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-61-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-60-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-59-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-58-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-57-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-56-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-55-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-54-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-53-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-52-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-51-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-50-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-49-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-48-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-47-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-46-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-45-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-44-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-43-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-42-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-41-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-40-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-39-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-38-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-37-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-36-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-35-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-34-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-33-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-32-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-31-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-30-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-29-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-28-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-27-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-26-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-25-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-24-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-23-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-22-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-21-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-20-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-19-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-18-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-17-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-16-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-15-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-14-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-13-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-12-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-11-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-10-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-9-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-8-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-7-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-6-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-5-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-4-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Three of the four entries of imx_uart_devdata[] use .uts_reg =
IMX21_UTS. The difference in the .devtype member isn't relevant, the
only thing that matters is if is equal to IMX1_UART.
So use an entry with .devtype = IMX21_UART on all platforms but i.MX1.
There is no need to have the dev types in an array, so split them up in
two separate variables.
The fsl,imx53-uart devinfo can go away because in the binding and also
the dts files all fsl,imx53-uart devices also are compatible to
fsl,imx21-uart. That's not the case for fsl,imx6q-uart (which is a bit
strange IMHO), so the fsl,imx6q-uart must stay around.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230911085451.628798-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace 740/750/760 with generic terms like 74x/75x/76x to account for
variants like 741, 752 and 762.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230905151300.15365-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform_get_irq might be failed and return a negative result. So
there should have an error handling code.
Fixed this by adding an error handling code.
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Link: https://lore.kernel.org/r/tencent_234B0AACD06350E10D7548C2E086A9166305@qq.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sort drivers in alphabetic order in Makefile to make it easier to find
the correct line. In case the CONFIG and filenames disagree, sort using
the filename (ignore 8250 prefix while sorting).
In addition, place 8250_early separately above the drivers.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230912103558.20123-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sort drivers in alphabetic order in Makefile to make it easier to find
the correct line. In case the CONFIG and filenames disagree, sort using
the filename (but ignoring "serial" prefixes).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230912103558.20123-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_exar includes linux/8250_pci.h and depends on SERIAL_8250_PCI.
Neither is necessary so this patch removes the include and changes
the depends on to SERIAL_8250 && PCI (taken from SERIAL_8250_PCI).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230915094336.13278-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_mid uses FL_*BASE* from linux/8250_pci.h and nothing else. The
code can be simplified by directly defining BARs within the driver
instead.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230915094336.13278-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe process may generate EPROBE_DEFER. In this case
dev_err_probe() can still record err information. Otherwise
it may pollute logs on that occasion.
This also helps simplifing code and standardizing the error output.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230912165607.402580-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe process may generate EPROBE_DEFER. In this case
dev_err_probe() can still record err information. Otherwise
it may pollute logs on that occasion.
This also helps simplifing code and standardizing the error output.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230912165540.402504-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART_IIR_64BYTE_FIFO is always being used in conjunction with
UART_IIR_FIFO_ENABLED. Introduce a joined UART_IIR_FIFO_ENABLED_16750
definition and use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230911144308.4169752-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for break control to the stm32 serial driver.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230906151547.840302-1-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This macro is not used anywhere.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230905181649.134720-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add check for ioremap() and return the error if it fails in order to
guarantee the success of ioremap().
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Acked-by: Jacky Huang <ychuang3@nuvoton.com>
Link: https://lore.kernel.org/r/20230915071106.3347-1-nichen@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the leaf driver wants to use IRQ polling (irq = 0) and
IIR register shows that an interrupt happened in the 8250 hardware
the IRQ data can be NULL. In such a case we need to skip the wake
event as we came to this path from the timer interrupt and quite
likely system is already awake.
Without this fix we have got an Oops:
serial8250: ttyS0 at I/O 0x3f8 (irq = 0, base_baud = 115200) is a 16550A
...
BUG: kernel NULL pointer dereference, address: 0000000000000010
RIP: 0010:serial8250_handle_irq+0x7c/0x240
Call Trace:
? serial8250_handle_irq+0x7c/0x240
? __pfx_serial8250_timeout+0x10/0x10
Fixes: 0ba9e3a13c ("serial: 8250: Add missing wakeup event reporting")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230831222555.614426-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Itanium architecture is obsolete, and an informal survey [0] reveals
that any residual use of Itanium hardware in production is mostly HP-UX
or OpenVMS based. The use of Linux on Itanium appears to be limited to
enthusiasts that occasionally boot a fresh Linux kernel to see whether
things are still working as intended, and perhaps to churn out some
distro packages that are rarely used in practice.
None of the original companies behind Itanium still produce or support
any hardware or software for the architecture, and it is listed as
'Orphaned' in the MAINTAINERS file, as apparently, none of the engineers
that contributed on behalf of those companies (nor anyone else, for that
matter) have been willing to support or maintain the architecture
upstream or even be responsible for applying the odd fix. The Intel
firmware team removed all IA-64 support from the Tianocore/EDK2
reference implementation of EFI in 2018. (Itanium is the original
architecture for which EFI was developed, and the way Linux supports it
deviates significantly from other architectures.) Some distros, such as
Debian and Gentoo, still maintain [unofficial] ia64 ports, but many have
dropped support years ago.
While the argument is being made [1] that there is a 'for the common
good' angle to being able to build and run existing projects such as the
Grid Community Toolkit [2] on Itanium for interoperability testing, the
fact remains that none of those projects are known to be deployed on
Linux/ia64, and very few people actually have access to such a system in
the first place. Even if there were ways imaginable in which Linux/ia64
could be put to good use today, what matters is whether anyone is
actually doing that, and this does not appear to be the case.
There are no emulators widely available, and so boot testing Itanium is
generally infeasible for ordinary contributors. GCC still supports IA-64
but its compile farm [3] no longer has any IA-64 machines. GLIBC would
like to get rid of IA-64 [4] too because it would permit some overdue
code cleanups. In summary, the benefits to the ecosystem of having IA-64
be part of it are mostly theoretical, whereas the maintenance overhead
of keeping it supported is real.
So let's rip off the band aid, and remove the IA-64 arch code entirely.
This follows the timeline proposed by the Debian/ia64 maintainer [5],
which removes support in a controlled manner, leaving IA-64 in a known
good state in the most recent LTS release. Other projects will follow
once the kernel support is removed.
[0] https://lore.kernel.org/all/CAMj1kXFCMh_578jniKpUtx_j8ByHnt=s7S+yQ+vGbKt9ud7+kQ@mail.gmail.com/
[1] https://lore.kernel.org/all/0075883c-7c51-00f5-2c2d-5119c1820410@web.de/
[2] https://gridcf.org/gct-docs/latest/index.html
[3] https://cfarm.tetaneutral.net/machines/list/
[4] https://lore.kernel.org/all/87bkiilpc4.fsf@mid.deneb.enyo.de/
[5] https://lore.kernel.org/all/ff58a3e76e5102c94bb5946d99187b358def688a.camel@physik.fu-berlin.de/
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
("refactor Kconfig to consolidate KEXEC and CRASH options").
- kernel.h slimming work from Andy Shevchenko ("kernel.h: Split out a
couple of macros to args.h").
- gdb feature work from Kuan-Ying Lee ("Add GDB memory helper
commands").
- vsprintf inclusion rationalization from Andy Shevchenko
("lib/vsprintf: Rework header inclusions").
- Switch the handling of kdump from a udev scheme to in-kernel handling,
by Eric DeVolder ("crash: Kernel handling of CPU and memory hot
un/plug").
- Many singleton patches to various parts of the tree
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZO2GpAAKCRDdBJ7gKXxA
juW3AQD1moHzlSN6x9I3tjm5TWWNYFoFL8af7wXDJspp/DWH/AD/TO0XlWWhhbYy
QHy7lL0Syha38kKLMXTM+bN6YQHi9AU=
=WJQa
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2023-08-28-22-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- An extensive rework of kexec and crash Kconfig from Eric DeVolder
("refactor Kconfig to consolidate KEXEC and CRASH options")
- kernel.h slimming work from Andy Shevchenko ("kernel.h: Split out a
couple of macros to args.h")
- gdb feature work from Kuan-Ying Lee ("Add GDB memory helper
commands")
- vsprintf inclusion rationalization from Andy Shevchenko
("lib/vsprintf: Rework header inclusions")
- Switch the handling of kdump from a udev scheme to in-kernel
handling, by Eric DeVolder ("crash: Kernel handling of CPU and memory
hot un/plug")
- Many singleton patches to various parts of the tree
* tag 'mm-nonmm-stable-2023-08-28-22-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (81 commits)
document while_each_thread(), change first_tid() to use for_each_thread()
drivers/char/mem.c: shrink character device's devlist[] array
x86/crash: optimize CPU changes
crash: change crash_prepare_elf64_headers() to for_each_possible_cpu()
crash: hotplug support for kexec_load()
x86/crash: add x86 crash hotplug support
crash: memory and CPU hotplug sysfs attributes
kexec: exclude elfcorehdr from the segment digest
crash: add generic infrastructure for crash hotplug support
crash: move a few code bits to setup support of crash hotplug
kstrtox: consistently use _tolower()
kill do_each_thread()
nilfs2: fix WARNING in mark_buffer_dirty due to discarded buffer reuse
scripts/bloat-o-meter: count weak symbol sizes
treewide: drop CONFIG_EMBEDDED
lockdep: fix static memory detection even more
lib/vsprintf: declare no_hash_pointers in sprintf.h
lib/vsprintf: split out sprintf() and friends
kernel/fork: stop playing lockless games for exe_file replacement
adfs: delete unused "union adfs_dirtail" definition
...
This reverts commit 6a4197f976
New SoC will use ttyS0 instead of ttyAML, so T7 SoC doesn't need a
OF_EARLYCON_DECLARE.
Fixes: 6a4197f976 ("tty: serial: meson: Add a earlycon for the T7 SoC")
Signed-off-by: Lucas Tanure <tanure@linux.com>
Link: https://lore.kernel.org/r/20230827082944.5100-1-tanure@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 BCM7271 UART is not a direct match to PORT_16550A and other
generic ports do not match its hardware capabilities. PORT_ALTR matches
the rx trigger levels, but its vendor configurations are not compatible.
Unfortunately this means we need to create another port to fully capture
the hardware capabilities of the BCM7271 UART.
To alleviate some latency pressures, we default the rx trigger level to 8.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/1692643978-16570-1-git-send-email-justin.chen@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retrieve rs485 devicetree properties on registration of sc16is7xx ports in
case they are attached to an rs485 transceiver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configuring a pin as an output pin with a value of logic 0, we
end up as having a value of logic 1 on the output pin. Setting a
logic 0 a second time (or more) after that will correctly output a
logic 0 on the output pin.
By default, all GPIO pins are configured as inputs. When we enter
sc16is7xx_gpio_direction_output() for the first time, we first set the
desired value in IOSTATE, and then we configure the pin as an output.
The datasheet states that writing to IOSTATE register will trigger a
transfer of the value to the I/O pin configured as output, so if the
pin is configured as an input, nothing will be transferred.
Therefore, set the direction first in IODIR, and then set the desired
value in IOSTATE.
This is what is done in NXP application note AN10587.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 679875d1d8 ("sc16is7xx: Separate GPIOs from modem control lines")
and commit 21144bab4f ("sc16is7xx: Handle modem status lines")
changed the function of the GPIOs pins to act as modem control
lines without any possibility of selecting GPIO function.
As a consequence, applications that depends on GPIO lines configured
by default as GPIO pins no longer work as expected.
Also, the change to select modem control lines function was done only
for channel A of dual UART variants (752/762). This was not documented
in the log message.
Allow to specify GPIO or modem control line function in the device
tree, and for each of the ports (A or B).
Do so by using the new device-tree property named
"nxp,modem-control-line-ports" (property added in separate patch).
When registering GPIO chip controller, mask-out GPIO pins declared as
modem control lines according to this new DT property.
Fixes: 679875d1d8 ("sc16is7xx: Separate GPIOs from modem control lines")
Fixes: 21144bab4f ("sc16is7xx: Handle modem status lines")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230807214556.540627-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c8f71b49ee ("serial: sc16is7xx: setup GPIO controller later
in probe") moved GPIO setup code later in probe function. Doing so
also required to move ports cleanup code (out_ports label) after the
GPIO cleanup code.
After these moves, the out_thread label becomes misplaced and makes
part of the cleanup code illogical.
This patch remove the now obsolete out_thread label and make GPIO
setup code jump to out_ports label if it fails.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230807214556.540627-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sc16is7xx_config_rs485() function is called only for the second
port (index 1, channel B), causing initialization problems for the
first port.
For the sc16is7xx driver, port->membase and port->mapbase are not set,
and their default values are 0. And we set port->iobase to the device
index. This means that when the first device is registered using the
uart_add_one_port() function, the following values will be in the port
structure:
port->membase = 0
port->mapbase = 0
port->iobase = 0
Therefore, the function uart_configure_port() in serial_core.c will
exit early because of the following check:
/*
* If there isn't a port here, don't do anything further.
*/
if (!port->iobase && !port->mapbase && !port->membase)
return;
Typically, I2C and SPI drivers do not set port->membase and
port->mapbase.
The max310x driver sets port->membase to ~0 (all ones). By
implementing the same change in this driver, uart_configure_port() is
now correctly executed for all ports.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there's no irq(this can be due to various reasons, for example,
no irq from HW support, or we just want to use poll solution, and so
on), falling back to poll is still better than no support at all.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20230806092056.2467-3-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In tegra_uart_hw_init(), the return value of clk_prepare_enable() should
be checked since it might fail.
Fixes: e9ea096dd2 ("serial: tegra: add serial driver")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Link: https://lore.kernel.org/r/20230817105406.228674-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the Sifive Uart is not used as the wake up source, suspend the uart
before the system enter the suspend state to prevent it woken up by
unexpected uart interrupt. Resume the uart once the system woken up.
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Reviewed-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20230815090216.2575971-1-nick.hu@sifive.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new Amlogic T7 SoC does not have a always-on uart,
so add OF_EARLYCON_DECLARE for it.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230814080128.143613-2-tanure@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In shutdown, RX DMA channel is terminated. If the DMA RX callback is
scheduled but not yet executed, while a new RX DMA transfer is started, the
callback can be executed, and then disturb the ongoing RX DMA transfer.
To avoid such a case, call dmaengine_synchronize in shutdown, after the
DMA RX channel is terminated.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-7-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's rather advised to rely on DMA pause / resume instead of
clearing/setting DMA request enable bit for the same purpose. Some DMA
request/acknowledge race may encountered by doing so. We prefer to use
dmaengine_pause and resume instead to pause a dma transfer when it is
necessary.
Create two new functions (stm32_usart_rx_dma_pause, stm32_usart_rx_dma
_resume) to handle dma error when pausing/resuming.
And rename stm32_usart_start_rx_dma_cyclic() to
stm32_usart_rx_dma_start_or_resume() and use this function to resume an
rx dma transfer. If resume fail, stm32_usart_rx_dma_start_or_resume can
create a new transfer to continue.
It is also safer to close DMA before reset DMAR in stm32_usart_shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-6-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create new function "stm32_usart_dma_pause_resume" that called dmaengine_
pause/resume and in case of error, terminate dma transaction.
Two other functions are created to facilitate the use of stm32_usart_dma
_pause_resume : stm32_usart_tx_dma_pause, stm32_usart_tx_dma_resume.
Equivalent functions for rx will be added in future patch.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-5-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename stm32_usart_rx_dma_enabled to stm32_usart_rx_dma_started in order
to match with stm32_usart_tx_dma_started.
Modify argument of stm32_usart_rx_dma_started from uart_port structure to
stm32_port structure to match with stm32_usart_tx_dma_started.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-4-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMAT is a configuration bit so it should be set at the startup of uart
port and not when a DMA transfer begins.
This patch move set of DMAT into set_termios and remove DMAT reset except
in shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's rather advised to rely on DMA pause / resume instead of
clearing/setting DMA request enable bit for the same purpose. Some DMA
request/acknowledge race may encountered by doing so. We prefer to use
dmaengine_pause and resume instead to pause a dma transfer when it is
necessary.
It is also safer to close DMA before reset DMAT in stm32_usart_shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to fix the serial core port DEVNAME to use a port id of the
hardware specific controller port instance instead of the port->line.
For example, the 8250 driver sets up a number of serial8250 ports
initially that can be inherited by the hardware specific driver. At that
the port->line no longer decribes the port's relation to the serial core
controller instance.
Let's fix the issue by assigning port->port_id for each serial core
controller port instance.
Fixes: 7d695d8376 ("serial: core: Fix serial_base_match() after fixing controller port name")
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811103648.2826-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is not always held when calling serial8250_clear_IER().
When an oops is in progress, the lock is tried to be taken and when it
is not, a warning is issued:
WARNING: CPU: 0 PID: 1 at drivers/tty/serial/8250/8250_port.c:707 +0x57/0x60
Modules linked in:
CPU: 0 PID: 1 Comm: init Not tainted 6.5.0-rc5-1.g225bfb7-default+ #774 00f1be860db663ed29479b8255d3b01ab1135bd3
Hardware name: QEMU Standard PC ...
RIP: 0010:serial8250_clear_IER+0x57/0x60
...
Call Trace:
<TASK>
serial8250_console_write+0x9e/0x4b0
console_flush_all+0x217/0x5f0
...
Therefore, remove the annotation as it doesn't hold for all invocations.
The other option would be to make the lockdep test conditional on
'oops_in_progress' or pass 'locked' from serial8250_console_write(). I
don't think, that is worth it.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Cc: John Ogness <john.ogness@linutronix.de>
Fixes: d0b309a5d3 (serial: 8250: synchronize and annotate UART_IER access)
Link: https://lore.kernel.org/r/20230811064340.13400-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TX is handled by primary sequencer. After cancelling primary command, poll
primary sequencer's irq status instead of that of secondary.
While at it, also remove a couple of redundant lines that read from IRQ_EN
register and write back same.
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Link: https://lore.kernel.org/r/1691578393-9891-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter reports boot issues with duplicate sysfs entries for multiport
drivers. Let's go back to using port->line for now to fix the regression.
With this change, the serial core port device names are not correct for the
hardware specific 8250 single port drivers, but that's a cosmetic issue for
now.
Fixes: d962de6ae5 ("serial: core: Fix serial core port id to not use port->line")
Reported-by: Guenter Roeck <groeck7@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230806062052.47737-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unloading a hardware specific 8250 driver can produce error "Unable to
handle kernel paging request at virtual address" about ten seconds after
unloading the driver. This happens on uart_hangup() calling
uart_change_pm().
Turns out commit 04e82793f0 ("serial: 8250: Reinit port->pm on port
specific driver unbind") was only a partial fix. If the hardware specific
driver has initialized port->pm function, we need to clear port->pm too.
Just reinitializing port->ops does not do this. Otherwise serial8250_pm()
will call port->pm() instead of serial8250_do_pm().
Fixes: 04e82793f0 ("serial: 8250: Reinit port->pm on port specific driver unbind")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230804131553.52927-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After fixing the serial core port device to use port->port_id instead of
port->line, unloading a hardware specific 8250 port driver started
producing an error for "sysfs: cannot create duplicate filename".
This is happening as we are wrongly initializing port->port_id to zero
when adding back serial8250_isa_devs instances, and the serial8250:0.0
sysfs entry may already exist. For serial8250 devices, we typically have
multiple devices mapped to a single driver instance. For the
serial8250_isa_devs instances, the port->port_id is the same as port->line.
Let's fix the issue by re-initializing port_id when adding back the
serial8250_isa_devs instances in serial8250_unregister_port().
Fixes: d962de6ae5 ("serial: core: Fix serial core port id to not use port->line")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230804123546.25293-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kmemleak reports issues for serial8250 ports after the hardware specific
driver takes over on boot as noted by Tomi.
The kerneldoc for device_initialize() says we must call device_put()
after calling device_initialize(). We are calling device_put() on the
error path, but are missing it from the device remove path. This causes
release() to never get called for the devices on remove.
Let's add the missing put_device() calls for both serial ctrl and
port devices.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Reported-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20230804090909.51529-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpm_uart_map_pram() and cpm_uart_unmap_pram() are very
similar for CPM1 and CPM2.
On CPM1 cpm_uart_map_pram() uses of_iomap() while CPM2 uses
of_address_to_resource()/ioremap(). CPM2 version will also
work on CPM1.
On CPM2 cpm_uart_map_pram() and cpm_uart_unmap_pram() has a special
handling for SMC. Just gate it by an IS_ENABLED(CONFIG_CPM2).
So move the CPM2 version into cpm_uart_core.c which is the only
user of those two fonctions and refactor to also handle CPM1 as
mentionned above.
PROFF_SMC_SIZE is only defined for SMC2 and used only there. To make
it simple, just use the numerical value 64, this is the only place
it is used and anyway there's already the same numerical value for
the alignment.
Use cpm_muram_alloc() instead of cpm_dpalloc() macro.
Then cpm_uart_cpm1.c and cpm_uart_cpm2.c are now empty and go away.
Replace printk(KERN_WARN by pr_warn( to make checkpatch happier.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/44a266106c421319aa8e700c2db52d5dcd652c0f.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpm_uart_freebuf() is identical for CPM1 and CPM2.
cpm_uart_allocbuf() only has a small difference between CPM1 and CPM2
as shown below:
CPM1:
if (is_con) {
/* was hostalloc but changed cause it blows away the */
/* large tlb mapping when pinning the kernel area */
mem_addr = (u8 *) cpm_dpram_addr(cpm_dpalloc(memsz, 8));
dma_addr = (u32)cpm_dpram_phys(mem_addr);
} else
mem_addr = dma_alloc_coherent(pinfo->port.dev, memsz, &dma_addr,
GFP_KERNEL);
CPM2:
if (is_con) {
mem_addr = kzalloc(memsz, GFP_NOWAIT);
dma_addr = virt_to_bus(mem_addr);
}
else
mem_addr = dma_alloc_coherent(pinfo->port.dev, memsz, &dma_addr,
GFP_KERNEL);
Refactor this by using IS_ENABLED(CONFIG_CPM1)
and move both functions in cpm_uart_core.c as they are used only there.
While doing this, add the necessary casts to silence sparse for the CPM1
part. This is because a dma alloc is not expected to be an iomem but
for CPM1 as we use DPRAM this is seen as iomem.
Also replace calls to cpm_dpxxxx() by relevant cpm_muram_xxxx() calls.
This is needed at least for cpm_dpram_phys() which is only defined
for CPM1. Just do the same for all so that cpm_dpxxxx() macros can get
droped in the future.
To silence checkpatch, replace printk(KERN_ERR by pr_err( and display
function name instead of hard coded filename. Also replace
mem_addr == NULL by !mem_addr.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/606dfdd258a4f2f2882e2e189bef37526bb3b499.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CPMFCR_EB is the same as SMC_EB and is defined
for both CPM1 and CPM2.
CPMFCR_GBL is defined as 0 for CPM1.
Therefore the CPM2 version of cpm_set_scc_fcr() and
cpm_set_smc_fcr() can be used on both CPM1 and CPM2.
And cpm_set_brg() is already identical and just a
wrapper of cpm_setbrg().
In addition those three fonctions are only called once
from cpm_uart_core.c, so just replace the calls with
the content of the CPM2 versions of them.
And DPRAM_BASE is identical so can go in cpm_uart.h. While
moving it, use cpm_muram_addr() directly instead of the
cpm_dpram_addr() macro and remove __force tag which isn't needed.
Then cpm_uart_cpm1.h and cpm_uart_cpm2.h go away.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/6920e61fd362961ae1aeda897c8bfe1efacdc9dc.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_baudrate() is just a trivial wrapper to get_baudrate().
Use get_baudrate() directly and remove assignment in if condition.
And also remove uart_clock() which is not used since
commit 0b2a2e5b77 ("cpm_uart: Remove !CONFIG_PPC_CPM_NEW_BINDING
code")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/4d497386f576a3df768e44a04f9bb512e424c311.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpm_uart_init_portdesc()
smc1_lineif()
smc2_lineif()
scc1_lineif()
scc2_lineif()
scc3_lineif()
scc4_lineif()
Those functions were removed by commit 0b2a2e5b77 ("cpm_uart: Remove
!CONFIG_PPC_CPM_NEW_BINDING code"). Remove stale prototypes.
UART_SMC{1..2} and UART_SCC{1..4} and SCC_WAIT_CLOSING macros are not
used anymore since the above commit.
cpm_uart_ports[] isn't used outside cpm_uart_core.c since the
same commit, so make it static.
cpm_uart_init_smc() and cpm_uart_init_scc() don't need a forward
declaration.
FLAG_DISCARDING and IS_DISCARDING have never been used since at
least 2.6.12 and the start of git repository for kernel.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/96ef20ae1df056d1b7967871ba6e27e5b5aaeea6.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module_mcb_driver() will set "THIS_MODULE" to driver.owner when
register a mcb_driver driver, so it is redundant initialization to set
driver.owner in mcb_driver statement. Remove it for clean code.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230804100843.100348-1-lizetao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a warning reported by coccinelle:
./drivers/tty/serial/8250/8250_men_mcb.c:226:6-19: WARNING:
Unsigned expression compared with zero: data -> line [ i ] < 0
The array "line" of serial_8250_men_mcb_data is used to record the
registered serial port. When register a port failed, it will return
an error code, but the type of "line" is "unsigned int", causing
the error code to reverse. Modify the type of "data -> line" to solve
this problem.
Fixes: 2554e6ba28 ("8250_men_mcb: Read num ports from register data.")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230803142053.1308926-1-lizetao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The data->line[i] is defined as unsigned int type, if(data->line[i] < 0)
is invalid, so replace data->line[i] with res.
./drivers/tty/serial/8250/8250_men_mcb.c:223:6-19: WARNING: Unsigned expression compared with zero: data->line[i] < 0.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=6088
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230803084753.51253-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least freeze, restore and thaw need to be set in order for the driver
to support system hibernation. The existing suspend/resume functions can
be reused since those functions don't touch the device's power state or
wakeup capability. Use the helper macros SET_SYSTEM_SLEEP_PM_OPS and
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for symmetry with similar drivers.
Signed-off-by: Anton Eliasson <anton.eliasson@axis.com>
Link: https://lore.kernel.org/r/20230803-samsung_tty_pm_ops-v1-1-1ea7be72194d@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit a85a6c86c2 ("driver core: platform: Clarify that
IRQ 0 is invalid"), there is no possible for
platform_get_irq() to return 0. Use the return value
from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230803091712.596987-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a warning reported by coccinelle:
./drivers/tty/serial/ma35d1_serial.c:791:3-8:
No need to set .owner here. The core will do it.
The module_platform_driver() will set "THIS_MODULE" to driver.owner
when register a driver for platform-level devices, so it is redundant
initialization to set driver.owner in ma35d1serial_driver statement.
Remove it to silence the warning.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230803032353.3045221-1-lizetao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While fixing DEVNAME to be more usable, I broke serial_base_match() as the
ctrl and port prefix for device names seemed unnecessary.
The prefixes are still needed by serial_base_match() to probe the serial
base controller port, and serial tx is now broken.
Let's fix the issue by checking against dev->type and drv->name instead
of the prefixes that are no longer in the DEVNAME.
Fixes: 1ef2c2df11 ("serial: core: Fix serial core controller port name to show controller id")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202308021529.35b3ad6c-oliver.sang@intel.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230803071034.25571-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are missing the serial core controller id for the serial core port
name. Let's fix the issue for sane sysfs output, and to avoid issues
addressing serial ports later on.
And as we're now showing the controller id, the "ctrl" and "port" prefix
for the DEVNAME become useless, we can just drop them. Let's standardize on
DEVNAME:0 for controller name, where 0 is the controller id. And
DEVNAME:0.0 for port name, where 0.0 are the controller id and port id.
This makes the sysfs output nicer, on qemu for example:
$ ls /sys/bus/serial-base/devices
00:04:0 serial8250:0 serial8250:0.2
00:04:0.0 serial8250:0.1 serial8250:0.3
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230725054216.45696-4-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core port id should be serial core controller specific port
instance, which is not always the port->line index.
For example, 8250 driver maps a number of legacy ports, and when a
hardware specific device driver takes over, we typically have one
driver instance for each port. Let's instead add port->port_id to
keep track serial ports mapped to each serial core controller instance.
Currently this is only a cosmetic issue for the serial core port device
names. The issue can be noticed looking at /sys/bus/serial-base/devices
for example though. Let's fix the issue to avoid port addressing issues
later on.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230725054216.45696-3-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not read the data register to clear the error flags for lpuart32
platforms, the additional read may cause the receive FIFO underflow
since the DMA has already read the data register.
Actually all lpuart32 platforms support write 1 to clear those error
bits, let's use this method to better clear the error flags.
Fixes: 42b68768e5 ("serial: fsl_lpuart: DMA support for 32-bit variant")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230801022304.24251-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'status' is assigned a result from readl(). There is no need for the
variable to be 'unsigned long'. readl() returns 32bit values.
Provided, this is a Nios II driver (32-bit), there is no change in
semantics. This only makes the type explicit.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20230731080244.2698-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart code currently does the following in uart_write() and
uart_flush_buffer():
if (cond) {
WARN_ON(1);
return;
}
It can be rewritten to more obvious and more readable:
if (WARN_ON(cond))
return;
Do so.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230731080244.2698-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small TTY and serial driver fixes for 6.5-rc4 for some
reported problems. Included in here is:
- TIOCSTI fix for braille readers
- documentation fix for minor numbers
- MAINTAINERS update for new serial files in -rc1
- minor serial driver fixes for reported problems
All of these have been in linux-next with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZMZCMQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym8fQCdGtm3DH+/BVKEebLUBlTb2Gz3xrIAnjeDVdP3
8Yztt4MNSYi7gvOMHQi5
=e8rX
-----END PGP SIGNATURE-----
Merge tag 'tty-6.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small TTY and serial driver fixes for 6.5-rc4 for some
reported problems. Included in here is:
- TIOCSTI fix for braille readers
- documentation fix for minor numbers
- MAINTAINERS update for new serial files in -rc1
- minor serial driver fixes for reported problems
All of these have been in linux-next with no reported problems"
* tag 'tty-6.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_dw: Preserve original value of DLF register
tty: serial: sh-sci: Fix sleeping in atomic context
serial: sifive: Fix sifive_serial_console_setup() section
Documentation: devices.txt: reconcile serial/ucc_uart minor numers
MAINTAINERS: Update TTY layer for lists and recently added files
tty: n_gsm: fix UAF in gsm_cleanup_mux
TIOCSTI: always enable for CAP_SYS_ADMIN
Each of the 4 PCI functions on ASIX AX99100 PCIe to Multi I/O
Controller can be configured as a single-port serial port controller.
The subvendor id is 0x1000 when configured as serial port and MSI
interrupts are supported.
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230724083933.3173513-4-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The global pointer 'sprd_port' may not zero when sprd_probe returns
failure, that is a risk for sprd_port to be accessed afterward, and
may lead to unexpected errors.
For example:
There are two UART ports, UART1 is used for console and configured in
kernel command line, i.e. "console=";
The UART1 probe failed and the memory allocated to sprd_port[1] was
released, but sprd_port[1] was not set to NULL;
In UART2 probe, the same virtual address was allocated to sprd_port[2],
and UART2 probe process finally will go into sprd_console_setup() to
register UART1 as console since it is configured as preferred console
(filled to console_cmdline[]), but the console parameters (sprd_port[1])
belong to UART2.
So move the sprd_port[] assignment to where the port already initialized
can avoid the above issue.
Fixes: b7396a38fb ("tty/serial: Add Spreadtrum sc9836-uart driver support")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20230725064053.235448-1-chunyan.zhang@unisoc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the IOControl register bits description in the page 31 of
the product datasheet, we know the bit 3 of IOControl register is
softreset, this bit will self-clearing once the reset finish.
In the probe, the softreset bit is set, and when we read this register
from debugfs/regmap interface, we found the softreset bit is still
setting, this confused us for a while. Finally we found this register
is cached, to read the real value from register, we could put it
into the regmap_volatile().
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20230724034727.17335-1-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
in asc_init_port, clk_prepare_enable may fail, therefore, the
return value of clk_prepare_enable should be checked.
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Link: https://lore.kernel.org/r/20230717144733.24194-1-ruc_gongyuanjun@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Macroses for name generation are not useful. They hide the real place
for object declaration. Instead, use direct names such as
'meson_uart_driver_*' and 'meson_serial_console_*' for all objects.
Additionally, rename 'MESON_SERIAL_CONSOLE_DEFINE()' to
'MESON_SERIAL_CONSOLE()', and 'MESON_UART_DRIVER_DEFINE()' to
'MESON_UART_DRIVER()' to simplify the code.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230728071522.17503-1-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ioremap() fails, it returns NULL pointer, not ERR_PTR(), fix the
return value check and call release_mem_region() to release resource.
Fixes: c563831ba8 ("8250_men_mcb: Make UART config auto configurable")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20230728085723.3195044-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preserve the original value of the Divisor Latch Fraction (DLF) register.
When the DLF register is modified without preservation, it can disrupt
the baudrate settings established by firmware or bootloader, leading to
data corruption and the generation of unreadable or distorted characters.
Fixes: 701c5e73b2 ("serial: 8250_dw: add fractional divisor support")
Cc: stable <stable@kernel.org>
Signed-off-by: Ruihong Luo <colorsu1922@gmail.com>
Link: https://lore.kernel.org/stable/20230713004235.35904-1-colorsu1922%40gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230713004235.35904-1-colorsu1922@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is called indirectly from the platform driver probe
function. Even if the driver is built in, it may be probed after
free_initmem() due to deferral or unbinding/binding via sysfs.
Thus the function cannot be marked as __init.
Fixes: 45c054d081 ("tty: serial: add driver for the SiFive UART")
Cc: stable <stable@kernel.org>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20230624060159.3401369-1-samuel.holland@sifive.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-15-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-14-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-13-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-12-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-11-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-10-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20230712062853.11007-9-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-8-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-7-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-6-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-5-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-4-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-3-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-2-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-1-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the clock-rate debug printk more readable by using an equal sign
instead of a dash as separator between names and values and adding some
spaces:
qcom_geni_serial 988000.serial: desired_rate = 1843200, clk_rate = 7372800, clk_div = 4
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230714130214.14552-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The operating-performance-point vote needs to be dropped when shutting
down the port to avoid wasting power by keeping resources like power
domains in an unnecessarily high performance state (e.g. when a UART
connected Bluetooth controller is not in use).
Fixes: a5819b548a ("tty: serial: qcom_geni_serial: Use OPP API to set clk/perf state")
Cc: stable@vger.kernel.org # 5.9
Cc: Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230714130214.14552-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add IDLE interrupt support for receive dma on imx7ulp/imx8ulp/imx8qxp
platforms to replace the receive dma timer function, because the receive
dma timer has bigger latency than idle interrupt triggering, which may
cause the Bluetooth Firmware download timeout on Android platform(it
has a limited FW download time window).
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230710013857.7396-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the lpuart32_int() below lpuart_copy_rx_to_tty(), this is a
preparation patch for the next patch to avoid the function declaration,
no actual functional changes.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230710013857.7396-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mrvl,pxa-uart already supports earlycon and both compatible strings use
the same driver, so there's no reason for mmp-uart to not have earlycon
as well.
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20230721210042.21535-2-duje.mihanovic@skole.hr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement separate uart_data to ensure proper devname value for the A1
SoC family. Use 'ttyS' devname, as required by the A1 architecture,
instead of the legacy gx architecture.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230705181833.16137-6-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to use the correct devname value for the S4 SoC family, it
is imperative that we implement separate uart_data. Unlike the legacy
g12a architecture, the S4 architecture should employ the use of 'ttyS'
devname.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230705181833.16137-5-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is worth noting that the devname ttyS is a widely recognized tty name
and is commonly used by many uart device drivers. Given the established
usage and compatibility concerns, it may not be feasible to change the
devname for older SoCs. However, for new definitions, it is acceptable
and even recommended to use a new devname to help ensure clarity and
avoid any potential conflicts on lower or upper software levels.
For more information please refer to IRC discussion at [1].
Links:
[1]: https://libera.irclog.whitequark.org/linux-amlogic/2023-07-03
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Link: https://lore.kernel.org/r/20230705181833.16137-4-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Actually, the meson_uart module is already a platform_driver, but it is
currently registered manually and the uart core registration is run
outside the probe() scope, which results in some restrictions. For
instance, it is not possible to communicate with the OF subsystem
because it requires an initialized device object.
To address this issue, apply module_platform_driver() instead of direct
module init/exit routines. Additionally, move uart_register_driver() to
the driver probe(), and destroy manual console registration because it's
already run in the uart_register_driver() flow.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230705181833.16137-3-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_probe() helper for error checking and standard logging.
It makes the driver's probe() function a little bit shorter.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230705181833.16137-2-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART ports created by this driver were not usable out of
the box, so let the configuration be handled by the 8250 UART
subsystem. This makes the implementation simpler and the UART
port more usable.
The 8250 UART subsystem will take care of requesting the memory
resources, but the driver needs to first read the register where
the num ports is set, so a request of the resource is needed
before registering the UART port.
Co-developed-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Javier Rodriguez <josejavier.rodriguez@duagon.com>
Link: https://lore.kernel.org/r/20230705131423.30552-4-josejavier.rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IP Core Z025 and Z057 have a register where the amount of UART
ports is specified. Such register is located at offset 0x40.
This patch fixes the way the UART ports is calculated by reading
the actual register. Additionally a refactor was needed to achieve
this so we can keep track of the UART line and its offset which
also improves the remove callback.
Co-developed-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Javier Rodriguez <josejavier.rodriguez@duagon.com>
Link: https://lore.kernel.org/r/20230705131423.30552-3-josejavier.rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some F215 FPGA multifunction boards announce themselves as 215.
This leads to a misconfigured clockrate. The F215 is the same board
as G215 but with different cPCI interface so make them get the same
configuration
Co-developed-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Javier Rodriguez <josejavier.rodriguez@duagon.com>
Link: https://lore.kernel.org/r/20230705131423.30552-2-josejavier.rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the Tegra serial driver is probe before clocks are available then the
following error is seen on boot:
serial-tegra 3100000.serial: Couldn't get the clock
This has been observed on Jetson AGX Orin. Fix this by calling
dev_err_probe() instead of dev_err() to avoid printing an error on probe
deferral.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20230703113759.75608-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # for imx
Link: https://lore.kernel.org/r/20230724205440.767071-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the Qualcomm interconnect defines rather than magic numbers for the
icc tags also in the restore() PM callback.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20230711160516.30502-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reconcile devices.txt with serial/ucc_uart.c regarding device number
assignments. ucc_uart.c supports 4 ports and uses minor devnums
46-49, so update devices.txt with that info.
Then update ucc_uart.c's reference to the location of the devices.txt
list in the kernel source tree.
Fixes: d7584ed2b9 ("[POWERPC] qe-uart: add support for Freescale QUICCEngine UART")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Timur Tabi <timur@kernel.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-serial@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Link: https://lore.kernel.org/r/20230724063341.28198-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The local 'flag' variable carries only TTY_NORMAL. So use that constant
directly and drop the variable.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230712081811.29004-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* move the declaration of flg (with the initializer) to the loop, so
there is no need to reset it to TTY_NORMAL by an 'else' branch.
* use TTY_NORMAL as initializer above, not a magic zero constant
* remove the outer 'if' from this construct:
if (S & (A | B)) {
if (S & A)
X;
if (S & B)
Y;
}
* drop unlikely() as I doubt it has any benefits here. If it does,
provide numbers.
All four make the code easier to read.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Vineet Gupta <vgupta@kernel.org>
Acked-by: Vineet Gupta <vgupta@kernel.org>
Link: https://lore.kernel.org/r/20230712081811.29004-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__uart_start() does not need a tty struct. It works only with
uart_state. So pass the latter directly.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230712081811.29004-8-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both the character and flag are 8-bit values. So switch from unsigned
ints to u8s. The drivers will be cleaned up in the next round.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230712081811.29004-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Propagate u8 from the sysrq code further up to serial's
uart_handle_sysrq_char() and friends.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230712081811.29004-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The runtime PM state should not be changed by drivers that do not
implement runtime PM even if it happens to work around a bug in PM core.
With the wake irq arming now fixed, drop the bogus runtime PM state
update which left the device in active state (and could potentially
prevent a parent device from suspending).
Fixes: f3974413cf ("tty: serial: qcom_geni_serial: Wakeup IRQ cleanup")
Cc: 5.6+ <stable@vger.kernel.org> # 5.6+
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is the big set of tty/serial driver updates for 6.5-rc1.
Included in here are:
- tty_audit code cleanups from Jiri
- more 8250 cleanups from Ilpo
- samsung_tty driver bugfixes
- 8250 lock port updates
- usual fsl_lpuart driver updates and fixes
- other small serial driver fixes and updates, full details in the
shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZKKVTQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl+wACgwWX8fdrkBHASPVkcYOn8xa27E08AnjNz2Y8K
vvOII6EEYKwFjEkjAoIX
=By18
-----END PGP SIGNATURE-----
Merge tag 'tty-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty/serial driver updates for 6.5-rc1.
Included in here are:
- tty_audit code cleanups from Jiri
- more 8250 cleanups from Ilpo
- samsung_tty driver bugfixes
- 8250 lock port updates
- usual fsl_lpuart driver updates and fixes
- other small serial driver fixes and updates, full details in the
shortlog
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
tty_audit: make data of tty_audit_log() const
tty_audit: make tty pointers in exposed functions const
tty_audit: make icanon a bool
tty_audit: invert the condition in tty_audit_log()
tty_audit: use kzalloc() in tty_audit_buf_alloc()
tty_audit: use TASK_COMM_LEN for task comm
Revert "8250: add support for ASIX devices with a FIFO bug"
serial: atmel: don't enable IRQs prematurely
tty: serial: Add Nuvoton ma35d1 serial driver support
tty: serial: fsl_lpuart: add earlycon for imx8ulp platform
tty: serial: imx: fix rs485 rx after tx
selftests: tty: add selftest for tty timestamp updates
tty: tty_io: update timestamps on all device nodes
tty: fix hang on tty device with no_room set
serial: core: fix -EPROBE_DEFER handling in init
serial: 8250_omap: Use force_suspend and resume for system suspend
tty: serial: samsung_tty: Use abs() to simplify some code
tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() when iterating clk
tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() in case of error
serial: 8250: Apply FSL workarounds also without SERIAL_8250_CONSOLE
...
Here are a small set of changes for 6.5-rc1 for some driver core
changes. Included in here are:
- device property cleanups to make it easier to write "agnostic"
drivers when regards to the firmware layer underneath them (DT vs.
ACPI)
- debugfs documentation updates
- devres additions
- sysfs documentation and changes to handle empty directory creation
logic better
- tiny kernfs optimizations
- other tiny changes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZKKSEQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoowCfT+Joha+cz4edAFUvd55lKPPJJFsAoNiprHmX
di37sirvn6vo54Hk0Nyq
=qqTo
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are a small set of changes for 6.5-rc1 for some driver core
changes. Included in here are:
- device property cleanups to make it easier to write "agnostic"
drivers when regards to the firmware layer underneath them (DT vs.
ACPI)
- debugfs documentation updates
- devres additions
- sysfs documentation and changes to handle empty directory creation
logic better
- tiny kernfs optimizations
- other tiny changes
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: Skip empty folders creation
sysfs: Improve readability by following the kernel coding style
drivers: fwnode: fix fwnode_irq_get[_byname]()
ata: ahci_platform: Make code agnostic to OF/ACPI
device property: Implement device_is_compatible()
ACPI: Move ACPI_DEVICE_CLASS() to mod_devicetable.h
base/node: Use 'property' to identify an access parameter
driver core: device.h: add some missing kerneldocs
kernfs: fix missing kernfs_idr_lock to remove an ID from the IDR
isa: Remove unnecessary checks
MAINTAINERS: add entry for auxiliary bus
debugfs: Correct the 'debugfs_create_str' docs
serial: qcom_geni: Comment use of devm_krealloc rather than devm_krealloc_array
iio: adc: Use devm_krealloc_array
hwmon: pmbus: Use devm_krealloc_array
brings some order to the documentation directory, declutters the top-level
directory, and makes the documentation organization more closely match that
of the source.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAmSbDRwPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Y0b0H/A69Yxns1Bf465rNNINREaWWzJzIPGyJax9F
7x2zYphL2BLmDysHDvBpP858ytA4qzmqS7TopI1zjqTS6Uh4qTfsQTWNfk536Oyi
XOkKONPAqzuk4Pvsam4t46lMb5xqkyy7FcsZSp25ona7t8nLiTkoxTWIabvFziFN
F7qJ/u/Uzck53FgR2Xtss4vrkcWDTgva5SzQUhoxGfEqjEOoQi7CfqLQC468wfOt
/XlBCnTRPnZ6bFiD/9QHU+D0setWVBs0IJHH2ogDlx/FHOvp83haJHVRFNYpx0Gd
UY72gEbovzYauKMaa6azBo+1Tje6tTu6wfV3ZAG8UJYe/vJkdUw=
=EBMZ
-----END PGP SIGNATURE-----
Merge tag 'docs-arm-move' of git://git.lwn.net/linux
Pull arm documentation move from Jonathan Corbet:
"Move the Arm architecture documentation under Documentation/arch/.
This brings some order to the documentation directory, declutters the
top-level directory, and makes the documentation organization more
closely match that of the source"
* tag 'docs-arm-move' of git://git.lwn.net/linux:
dt-bindings: Update Documentation/arm references
docs: update some straggling Documentation/arm references
crypto: update some Arm documentation references
mips: update a reference to a moved Arm Document
arm64: Update Documentation/arm references
arm: update in-source documentation references
arm: docs: Move Arm documentation to Documentation/arch/
This reverts commit eb26dfe8aa.
Commit eb26dfe8aa ("8250: add support for ASIX devices with a FIFO
bug") merged on Jul 13, 2012 adds a quirk for PCI_VENDOR_ID_ASIX
(0x9710). But that ID is the same as PCI_VENDOR_ID_NETMOS defined in
1f8b061050c7 ("[PATCH] Netmos parallel/serial/combo support") merged
on Mar 28, 2005. In pci_serial_quirks array, the NetMos entry always
takes precedence over the ASIX entry even since it was initially
merged, code in that commit is always unreachable.
In my tests, adding the FIFO workaround to pci_netmos_init() makes no
difference, and the vendor driver also does not have such workaround.
Given that the code was never used for over a decade, it's safe to
revert it.
Also, the real PCI_VENDOR_ID_ASIX should be 0x125b, which is used on
their newer AX99100 PCIe serial controllers released on 2016. The FIFO
workaround should not be intended for these newer controllers, and it
was never implemented in vendor driver.
Fixes: eb26dfe8aa ("8250: add support for ASIX devices with a FIFO bug")
Cc: stable <stable@kernel.org>
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230619155743.827859-1-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The atmel_complete_tx_dma() function disables IRQs at the start
of the function by calling spin_lock_irqsave(&port->lock, flags);
There is no need to disable them a second time using the
spin_lock_irq() function and, in fact, doing so is a bug because
it will enable IRQs prematurely when we call spin_unlock_irq().
Just use spin_lock/unlock() instead without disabling or enabling
IRQs.
Fixes: 08f738be88 ("serial: at91: add tx dma support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/cb7c39a9-c004-4673-92e1-be4e34b85368@moroto.mountain
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds UART and console driver for Nuvoton ma35d1 Soc.
It supports full-duplex communication, FIFO control, and
hardware flow control.
Command line set "console=ttyNVT0,115200", NVT means
Nuvoton MA35 UART port. The UART driver probe will
create path named "/dev/ttyNVTx".
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230619032330.233796-2-ychuang570808@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal
active high") RS485 reception no longer works after a transmission.
The following scenario shows the problem:
1) Open a port in RS485 mode
2) Receive data from remote (OK)
3) Transmit data to remote (OK)
4) Receive data from remote (Nothing received)
In RS485 mode, imx_uart_start_tx() calls imx_uart_stop_rx() and, when the
transmission is complete, imx_uart_stop_tx() calls imx_uart_start_rx().
Since the above commit imx_uart_stop_rx() now sets the loopback bit but
imx_uart_start_rx() does not clear it causing the hardware to remain in
loopback mode and not receive external data.
Fix this by moving the existing loopback disable code to a helper function
and calling it from imx_uart_start_rx() too.
Fixes: 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230616104838.2729694-1-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Arm documentation has moved to Documentation/arch/arm; update the
last remaining references to match.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # for pwm
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The -EPROBE_DEFER error path in serial_base_device_init() is a bit
awkward. Before the call to device_initialize(dev) then we need to
manually release all the device resources. And after the call then we
need to call put_device() to release the resources. Doing either one
wrong will result in a leak or a use after free.
So let's wait to return -EPROBE_DEFER until after the call to
device_initialize(dev) so that way callers do not have to handle
-EPROBE_DEFER as a special case. Now callers can just use put_device()
for clean up.
The second issue with the -EPROBE_DEFER path is that deferring is not
supposed to be a fatal error, but instead it's normal part of the
init process and the kernel recovers from it automatically. That means
we should not print an error message but just a debug message on this
path.
Fixes: 539914240a ("serial: core: Fix probing serial_base_bus devices")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Message-ID: <18318adb-ab2c-4dcc-9f96-498a13d16b80@moroto.mountain>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not rely on autosuspend timeout for system suspend. Instead,
let's use force_suspend and force_resume functions. Otherwise the serial
port controller device may not be idled on suspend.
As we are doing a register write on suspend to configure the serial port,
we still need to runtime PM resume the port on suspend.
While at it, let's switch to pm_runtime_resume_and_get() and check for
errors returned. And let's add the missing line break before return to the
suspend function while at it.
Fixes: 09d8b2bdbc ("serial: 8250: omap: Provide ability to enable/disable UART as wakeup source")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Message-ID: <20230614045922.4798-1-tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the best clk is searched, we iterate over all possible clk.
If we find a better match, the previous one, if any, needs to be freed.
If a better match has already been found, we still need to free the new
one, otherwise it leaks.
Cc: <stable@vger.kernel.org> # v3.3+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Fixes: 5f5a7a5578 ("serial: samsung: switch to clkdev based clock lookup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Message-ID: <cf3e0053d2fc7391b2d906a86cd01a5ef15fb9dc.1686412569.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If clk_get_rate() fails, the clk that has just been allocated needs to be
freed.
Cc: <stable@vger.kernel.org> # v3.3+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Fixes: 5f5a7a5578 ("serial: samsung: switch to clkdev based clock lookup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Message-ID: <e4baf6039368f52e5a5453982ddcb9a330fc689e.1686412569.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LS1028A is using DMA with LPUART. Having RX watermark set to 1, means
DMA transactions are started only after receiving the second character.
On other platforms with newer LPUART IP, Receiver Idle Empty function
initiates the DMA request after the receiver is idling for 4 characters.
But this feature is missing on LS1028A, which is causing a 1-character
delay in the RX direction on this platform.
Set RX watermark to 0 to initiate RX DMA after each character.
Link: https://lore.kernel.org/linux-serial/20230607103459.1222426-1-robert.hodaszi@digi.com/
Fixes: 9ad9df8447 ("tty: serial: fsl_lpuart: Fix the wrong RXWATER setting for rx dma case")
Cc: stable <stable@kernel.org>
Signed-off-by: Robert Hodaszi <robert.hodaszi@digi.com>
Message-ID: <20230609121334.1878626-1-robert.hodaszi@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The need to handle the FSL variant of 8250 in a special way is also
present without console support. So soften the dependency for
SERIAL_8250_FSL from SERIAL_8250_CONSOLE to SERIAL_8250. To handle
SERIAL_8250=m, the FSL code can be modular, too, thus SERIAL_8250_FSL
becomes tristate.
Compiling 8250_fsl as a module requires adding a module license so this
is added, too. While add it also add a appropriate module description.
As then SERIAL_OF_PLATFORM=y + SERIAL_8250_FSL=m is a valid combination
(if COMPILE_TEST is enabled on a platform that is neither PPC, ARM nor
ARM64), the check in 8250_of.c must be weakened a bit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Message-ID: <20230609133932.786117-3-u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The put_device() function will call serial_base_ctrl_release() or
serial_base_port_release() so these kfrees() are a double free bug.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Message-ID: <ZH7tsTmWY5b/4m+6@moroto>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the error interrupt is never acknowledged, so once active it
will stay active indefinitely, causing the handler to be called in an
infinite loop.
Fixes: 2f0fc4159a ("SERIAL: Lantiq: Add driver for MIPS Lantiq SOCs.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Bernhard Seibold <mail@bernhard-seibold.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Message-ID: <20230602133029.546-1-mail@bernhard-seibold.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_mtk driver's runtime PM support has some issues:
- The bus clock is enabled (through runtime PM callback) later than a
register write
- runtime PM resume callback directly called in probe, but no
pm_runtime_set_active() call is present
- UART PM function calls the callbacks directly, _and_ calls runtime
PM API
- runtime PM callbacks try to do reference counting, adding yet another
count between runtime PM and clocks
This fragile setup worked in a way, but broke recently with runtime PM
support added to the serial core. The system would hang when the UART
console was probed and brought up.
Tony provided some potential fixes [1][2], though they were still a bit
complicated. The 8250_dw driver, which the 8250_mtk driver might have
been based on, has a similar structure but simpler runtime PM usage.
Simplify clock sequencing and runtime PM support in the 8250_mtk driver.
Specifically, the clock is acquired enabled and assumed to be active,
unless toggled through runtime PM suspend/resume. Reference counting is
removed and left to the runtime PM core. The serial pm function now
only calls the runtime PM API.
[1] https://lore.kernel.org/linux-serial/20230602092701.GP14287@atomide.com/
[2] https://lore.kernel.org/linux-serial/20230605061511.GW14287@atomide.com/
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Message-ID: <20230606091747.2031168-1-wenst@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes the property name read in the driver according to the YAML.
According to device-tree documentation, property names should not
include underscores.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Message-ID: <20230604083558.16661-1-rgallaispou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checking for NULL is incorrect as serial_base_ctrl_add() uses ERR_PTR().
Let's also pass any returned error along, there's no reason to translate
all errors to -ENODEV.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230602070007.59268-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a physical serial port device driver uses arch_initcall() we fail to
probe the serial_base_bus devices and the serial port tx fails. This is
because as serial_base_bus uses module_initcall().
Let's fix the issue by changing serial_base_bus to use arch_initcall().
Let's also return an error if a driver attempts to call uart_add_one_port()
too early.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/linux-serial/20230601132012.GB14287@atomide.com/T/#m6a40440fc04d551d27b147da8602e065c982a115
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230601141445.11321-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 84a9582fd2 ("serial: core: Start managing serial controllers to
enable runtime PM") required the caller to hold port_mutex rather than
taking it locally. However the mutex_unlock() call wasn't removed
causing the mutex to be dropped unexpectly. Remove the call to
mutex_unlock() (and fix up the early return) to restore correct
behaviour.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Steven Price <steven.price@arm.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230601105548.29965-1-steven.price@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to enable runtime PM for serial port device drivers in a generic
way. To do this, we want to have the serial core layer manage the
registered physical serial controller devices.
To manage serial controllers, let's set up a struct bus and struct device
for the serial core controller as suggested by Greg and Jiri. The serial
core controller devices are children of the physical serial port device.
The serial core controller device is needed to support multiple different
kind of ports connected to single physical serial port device.
Let's also set up a struct device for the serial core port. The serial
core port instances are children of the serial core controller device.
With the serial core port device we can now flush pending TX on the
runtime PM resume as suggested by Johan.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230525113034.46880-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new uart_write() function is only called from suspend/resume code, causing
a build warning when those are left out:
drivers/tty/serial/8250/8250_omap.c:169:13: error: 'uart_write' defined but not used [-Werror=unused-function]
Remove the #ifdefs and use the modern pm_ops/pm_sleep_ops and their wrappers
to let the compiler see where it's used but still drop the dead code.
Fixes: 398cecc248 ("serial: 8250: omap: Fix imprecise external abort for omap_8250_pm()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230517202012.634386-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After working quite a bit on erratic behaviour of the MPC83xx UART I
(think I) understood the problem. Expand the description accoringly to
conserve the knowledge for the future.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230524122754.481816-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a COMPILE_TEST configuration, the cpm_uart driver uses symbols from
the cpm_uart_cpm2.c file. This file is compiled only when CONFIG_CPM2 is
set.
Without this dependency, the linker fails with some missing symbols for
COMPILE_TEST configuration that needs SERIAL_CPM without enabling CPM2.
This lead to:
depends on CPM2 || CPM1 || (PPC32 && CPM2 && COMPILE_TEST)
This dependency does not make sense anymore and can be simplified
removing all the COMPILE_TEST part.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305160221.9XgweObz-lkp@intel.com/
Fixes: e3e7b13bff ("serial: allow COMPILE_TEST for some drivers")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230523085902.75837-3-herve.codina@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPUART IP now has two known bugs, one is that CTS has higher priority
than the break signal, which causes the break signal sending through
UARTCTRL_SBK may impacted by the CTS input if the HW flow control is
enabled. It exists on all platforms we support in this driver.
So we add a workaround patch for this issue: commit c4c81db5cf
("tty: serial: fsl_lpuart: disable the CTS when send break signal").
Another IP bug is i.MX8QM LPUART may have an additional break character
being sent after SBK was cleared. It may need to add some delay between
clearing SBK and re-enabling CTS to ensure that the SBK latch are
completely cleared.
But we found that during the delay period before CTS is enabled, there
is still a risk that Bluetooth data in TX FIFO may be sent out during
this period because of break off and CTS disabled(even if BT sets CTS
line deasserted, data is still sent to BT).
Due to this risk, we have to drop the CTS-disabling workaround for SBK
bugs, use TXINV seems to be a better way to replace SBK feature and
avoid above risk. Also need to disable the transmitter to prevent any
data from being sent out during break, then invert the TX line to send
break. Then disable the TXINV when turn off break and re-enable
transmitter.
Fixes: c4c81db5cf ("tty: serial: fsl_lpuart: disable the CTS when send break signal")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230519094751.28948-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current config comment for SERIAL_8250_FINTEK implies that this
option is only needed when one wants to support RS485. As it turns
out we also need to enable this option for RS232 support to function
correctly on some variants.
For example for variants such as the F71869AD attempting to use
multiple RS232 ports simultaneously without this option enabled can
result in data corruption.
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Link: https://lore.kernel.org/r/20230521075046.3539376-1-james.hilliard1@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coverity reports the Unchecked return value (CHECKED_RETURN) warning:
Calling dmaengine_tx_status without checking return value.
So here add the return value check for dmaengine_tx_status() function to
make coverity happy.
Fixes: cf9aa72d2f ("tty: serial: fsl_lpuart: optimize the timer based EOP logic")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230522025111.3747-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230525210147.734737-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART_IER register is modified twice by each console write
(serial8250_console_write()) under the port lock. Any driver code that
accesses UART_IER must do so with the port locked in order to ensure
consistent values, even when for read accesses.
Add locking, lockdep notation, and/or comments everywhere UART_IER is
accessed. The added locking is not fixing a real problem because it
occurs where the console is not active. However, adding the locking
to these non-critical paths greatly simplifies UART_IER access
tracking by establishing a general policy that all UART_IER access
is performed with the port locked.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230525093159.223817-9-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap8250_irq() accesses UART_IER. This register is modified twice
by each console write (serial8250_console_write()) under the port
lock. omap8250_irq() must also take the port lock to guanentee
synchronized access to UART_IER.
Since the port lock is already being taken for the stop_rx() callback
and since it is safe to call cancel_delayed_work() while holding the
port lock, simply extend the port lock region to include UART_IER
access.
Fixes: 1fe0e1fa32 ("serial: 8250_omap: Handle optional overrun-throttle-ms property")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230525093159.223817-8-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap8250_restore_regs() accesses UART_IER. This register is
modified twice by each console write (serial8250_console_write())
under the port lock. However, not all calls to omap8250_restore_regs()
are under the port lock.
Add the missing port locking around omap8250_restore_regs() calls. Add
lockdep notation to the omap8250_restore_regs().
Note that this is not fixing a real problem because the serial devices
are resumed before console printing is enabled.
However, adding this locking allows for clean locking semantics
for omap8250_restore_regs() so that lockdep can be used to identify
possible problems in the future. It also simplifies synchronization
of UART_IER in general by not needing to rely on such implementation
details.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230525093159.223817-7-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rx_dma() callback (omap_8250_rx_dma) accesses UART_IER. This
register is modified twice by each console write
(serial8250_console_write()) under the port lock. However, not
all calls to the rx_dma() callback are under the port lock.
Add the missing port locking around rx_dma() callback calls. Add
lockdep notation to the omap_8250_rx_dma().
Note that this is not fixing a real problem because:
1. Currently DMA is forced off for 8250_omap consoles.
2. The serial devices are resumed before console printing is enabled.
However, adding this locking allows for clean locking semantics
for the rx_dma() callback so that lockdep can be used to identify
possible problems in the future. It also simplifies synchronization
of UART_IER in general by not needing to rely on implementation
details such as 1 and 2.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230525093159.223817-6-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only user of the start_rx() callback (qcom_geni) directly calls
its own stop_rx() callback. Since stop_rx() requires that the
port->lock is taken and interrupts are disabled, the start_rx()
callback has the same requirement.
Fixes: cfab87c2c2 ("serial: core: Introduce callback for start_rx and do stop_rx in suspend only if this callback implementation is present.")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230525093159.223817-5-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uarts_ops stop_rx() callback expects that the port->lock is
taken and interrupts are disabled.
Fixes: 1fe0e1fa32 ("serial: 8250_omap: Handle optional overrun-throttle-ms property")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230525093159.223817-4-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uarts_ops stop_rx() callback expects that the port->lock is
taken and interrupts are disabled.
Fixes: c9d2325cdb ("serial: core: Do stop_rx in suspend path for console if console_suspend is disabled")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230525093159.223817-3-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_ops startup() callback is called without interrupts
disabled and without port->lock locked, relatively late during the
boot process (from the call path of console_on_rootfs()). If the
device is a console, it was already previously registered and could
be actively printing messages.
The console printing function serial8250_console_write() modifies
the interrupt register (UART_IER) under the port->lock with the
pattern: read, clear, restore.
Since some startup() callbacks are modifying UART_IER without the
port->lock locked, it is possible that the value intended to be
written by the startup() callback will get overwritten and be
lost.
CPU0 CPU1
serial8250_console_write omap_8250_startup
-------------------------- -----------------
spin_lock(port->lock)
oldval = read(UART_IER)
uart_console_write()
write(newval, UART_IER)
write(oldval, UART_IER)
spin_unlock(port->lock)
Add port->lock synchronization to the 8250 startup() callbacks
where they need to access UART_IER. This avoids racing with
serial8250_console_write().
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230525093159.223817-2-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver have a race, experienced only with PREEMPT_RT patchset:
CPU0 | CPU1
==================================================================
qcom_geni_serial_probe |
uart_add_one_port |
| serdev_drv_probe
| qca_serdev_probe
| serdev_device_open
| uart_open
| uart_startup
| qcom_geni_serial_startup
| enable_irq
| __irq_startup
| WARN_ON()
| IRQ not activated
request_threaded_irq |
irq_domain_activate_irq |
The warning:
894000.serial: ttyHS1 at MMIO 0x894000 (irq = 144, base_baud = 0) is a MSM
serial serial0: tty port ttyHS1 registered
WARNING: CPU: 7 PID: 107 at kernel/irq/chip.c:241 __irq_startup+0x78/0xd8
...
qcom_geni_serial 894000.serial: serial engine reports 0 RX bytes in!
Adding UART port triggers probe of child serial devices - serdev and
eventually Qualcomm Bluetooth hci_qca driver. This opens UART port
which enables the interrupt before it got activated in
request_threaded_irq(). The issue originates in commit f3974413cf
("tty: serial: qcom_geni_serial: Wakeup IRQ cleanup") and discussion on
mailing list [1]. However the above commit does not explain why the
uart_add_one_port() is moved above requesting interrupt.
[1] https://lore.kernel.org/all/5d9f3dfa.1c69fb81.84c4b.30bf@mx.google.com/
Fixes: f3974413cf ("tty: serial: qcom_geni_serial: Wakeup IRQ cleanup")
Cc: <stable@vger.kernel.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230505152301.2181270-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports:
drivers/tty/serial/8250/8250_bcm7271.c:1120 brcmuart_probe() warn:
'baud_mux_clk' from clk_prepare_enable() not released on lines: 1032.
The issue is fixed by using a managed clock.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Reported-by: XuDong Liu <m202071377@hust.edu.cn>
Link: https://lore.kernel.org/lkml/20230424125100.4783-1-m202071377@hust.edu.cn/
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230427181916.2983697-3-opendmb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports:
drivers/tty/serial/arc_uart.c:631 arc_serial_probe() warn:
'port->membase' from of_iomap() not released on lines: 631.
In arc_serial_probe(), if uart_add_one_port() fails,
port->membase is not released, which would cause a resource leak.
To fix this, I replace of_iomap with devm_platform_ioremap_resource.
Fixes: 8dbe1d5e09 ("serial/arc: inline the probe helper")
Signed-off-by: Ke Zhang <m202171830@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230428031636.44642-1-m202171830@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With W=1:
drivers/tty/serial/8250/8250_port.c:679: warning: Function parameter or member 'termios' not described in 'serial8250_em485_config'
Fix this by documenting the parameter.
Fixes: ae50bb2752 ("serial: take termios_rwsem for ->rs485_config() & pass termios as param")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/2bd1e62be1d5d33333002910372feecc6d52e78f.1682071013.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Advantech PCI-1611U card
Advantech provides opensource drivers for this and many others card
based on legacy copy of 8250_pci driver called adv950
https://www.advantech.com/emt/support/details/driver?id=1-TDOIMJ
It is hard to maintain to run as out of tree module on newer kernels.
Just adding PCI ID to kernel 8250_pci works perfect.
Signed-off-by: Vitaliy Tomin <tomin@iszf.irk.ru>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230423034512.2671157-1-tomin@iszf.irk.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Possibly the last PCI controller-based (i.e. not a soft/winmodem)
dial-up modem one can still buy.
Looks to have a stock XR17C154 PCI UART chip for communication, but for
some reason when provisioning the PCI IDs they swapped the vendor and
subvendor IDs. Otherwise this card would have worked out of the box.
Searching online, some folks seem to not have this issue and others do,
so it is possible only some batches of cards have this error.
Create a new macro to handle the switched IDs and add support here.
Signed-off-by: Andrew Davis <afd@ti.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230420160209.28221-1-afd@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value is only ever used as a return value for remove callbacks
of platform drivers. This return value is ignored by the driver core.
(The only effect is an error message, but uart_remove_one_port() already
emitted one in this case.)
So the return value isn't used at all and uart_remove_one_port() can be
changed to return void without any loss. Also this better matches the
Linux device model as remove functions are not supposed to fail.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512173810.131447-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Returning early from stm32_usart_serial_remove() results in a resource
leak as several cleanup functions are not called. The driver core ignores
the return value and there is no possibility to clean up later.
uart_remove_one_port() only returns non-zero if there is some
inconsistency (i.e. stm32_usart_driver.state[port->line].uart_port == NULL).
This should never happen, and even if it does it's a bad idea to exit
early in the remove callback without cleaning up.
This prepares changing the prototype of struct platform_driver::remove to
return void. See commit 5c5a7680e6 ("platform: Provide a remove callback
that returns no value") for further details about this quest.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512173810.131447-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As unmapped registers are at the tail of the array, the ARRAY_SIZE()
condition will catch them just fine. No need to define special
value for them.
Convert the arrays to u8 as all entiries are now positive.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230511121029.13128-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A non-trivial amount of RT288x/Au1xxx code is encapsulated into
ifdeffery in 8250_port / 8250_early and some if UPIO_AU blocks.
Create a separate file from them.
Also handle errors properly in the cases where RT288x/Au1xxx code is
not configured.
It seems that 0x1000 mapsize is likely overkill but I've kept it the
same as previously (the value was shrunk to that value in commit
b2b13cdfd0 ("SERIAL 8250: Fixes for Alchemy UARTs.")). Seemingly, the
driver only needs to access register at 0x28 for the divisor latch.
The Kconfig side is a bit tricky. As SERIAL_8250_RT288X is bool it can
only be =y. It is possible to have SERIAL_8250=m + SERIAL_8250_RT288X=y
which required altering when 8250/ is included or the rt288x would not
be built.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230511121029.13128-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add mapsize, bugs, and divisor latch read/write functions
(->dl_read/write()) into plat_serial8250_port to carry the setup
necessary for RT288x/Au1xxx devices over to uart port.
Document the added members with kerneldoc style but do not enable
kerneldoc yet as there are many fields which remain undocumented.
While at it, convert .bugs in struct uart_8250_port to u16 to match it
with the type used in struct plat_serial8250_port.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230511121029.13128-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Divisor latch read/write functions currently handle the value is int.
As the value is related to HW context, u32 makes much more sense than a
signed type.
While at it, name the parameters in the callback signature.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230511121029.13128-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already allocate CONFIG_SERIAL_8250_NR_UARTS, but only allow using
CONFIG_SERIAL_8250_RUNTIME_UARTS uarts unless nr_uarts module params
is set. This causes issues for using distro kernels on SoCs with a
large number of serial ports.
Let's allow up to CONFIG_SERIAL_8250_NR_UARTS instead. To do this, we init
the ports as needed if the initial uarts was too low. This way there's no
need to set the value for CONFIG_SERIAL_8250_RUNTIME_UARTS to some SoC
specific higher value. Typically the default value of 4 can be used as
set for legacy reasons.
Note that limiting the number of intial uarts still works as before
unless a serial console on a higher port is specified. In this case we
will increase the nr_ports up to the console port specified.
Suggested-by: Andrew Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230508111903.39339-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unbinding the console uart, we want to power down the uart hardware
on remove. For the console uart, the normal shutdown path will never get
called as the cons_filp stays open. Let's rearrange the dma related
functions a bit so we can call driver shutdown also on console uart rebind.
Currently we set up->dma on probe, but that causes issues calling
omap_8250_shutdown() on remove. The dma startup will not get called on
the next rebind as we still have up->dma set from probe.
Note that serial8250_release_dma() already checks for dma so we can
remove the check for it in 8205_omap driver.
With these changes we also avoid hogging dma virtual channels for the
unused uarts that may be limited on some devices.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230508082014.23083-5-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have the struct uart_8250_port instance recycled on device rebind while
the struct omap8250_priv instance is not. For the console uart,
__tty_hangup() does not call tty->ops->hangup() as cons_filp stays open,
and uart shutdown won't get called. This means we have a stale
priv->wakeirq handler around after unbind, and port->irq is not freed on
unbind.
There's no need to claim the interrupts on startup. We can fix this and
simplify the driver a bit by claiming the interrupts in probe, and clearing
them on remove. For the device interrupt, we can use devm_request_irq().
To do this, we change omap8250_irq() to use struct omap8250_priv data
directly so we don't have to wait for the assigned port from
serial8250_register_8250_port().
We must also drop IRQF_SHARED to set IRQ_NOAUTOEN to avoid spurious
interrupts until the port has been registered. There's no need for
IRQF_SHARED for 8250_omap, the serial port interrupt lines are dedicated
lines.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230508082014.23083-4-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We must idle the uart only after serial8250_unregister_port(). Otherwise
unbinding the uart via sysfs while doing cat on the port produces an
imprecise external abort:
mem_serial_in from omap_8250_pm+0x44/0xf4
omap_8250_pm from uart_hangup+0xe0/0x194
uart_hangup from __tty_hangup.part.0+0x37c/0x3a8
__tty_hangup.part.0 from uart_remove_one_port+0x9c/0x22c
uart_remove_one_port from serial8250_unregister_port+0x60/0xe8
serial8250_unregister_port from omap8250_remove+0x6c/0xd0
omap8250_remove from platform_remove+0x28/0x54
Turns out the driver needs to have runtime PM functional before the
driver probe calls serial8250_register_8250_port(). And it needs
runtime PM after driver remove calls serial8250_unregister_port().
On probe, we need to read registers before registering the port in
omap_serial_fill_features_erratas(). We do that with custom uart_read()
already.
On remove, after serial8250_unregister_port(), we need to write to the
uart registers to idle the device. Let's add a custom uart_write() for
that.
Currently the uart register access depends on port->membase to be
initialized, which won't work after serial8250_unregister_port().
Let's use priv->membase instead, and use it for runtime PM related
functions to remove the dependency to port->membase for early and
late register access.
Note that during use, we need to check for a valid port in the runtime PM
related functions. This is needed for the optional wakeup configuration.
We now need to set the drvdata a bit earlier so it's available for the
runtime PM functions.
With the port checks in runtime PM functions, the old checks for priv in
omap8250_runtime_suspend() and omap8250_runtime_resume() functions are no
longer needed and are removed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230508082014.23083-3-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If serial8250_register_8250_port() fails, the SoC can hang as the
deferred PMQoS work will still run as is not flushed and removed.
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230508082014.23083-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART011_CR_RXE is set in pl011_startup() during normal initialization, and
cleared by pl011_disable_uart() during port shutdown.
You can use a none-console port in poll mode like kgdboc does with
tty_find_polling_driver() after a port shutdown. But pl011_startup() is not
called in tty_find_polling_driver(). So you need to set UART011_CR_RXE to
reenable receive function.
Not sure setting UART011_CR_RXE in pl011_set_termios() is a good idea
through.
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Link: https://lore.kernel.org/r/20230501070909.1144547-1-xiehongyu1@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA transfer may end prematurely due to the DMA Rx timeout even during an
active transfer because a constant timeout does not accurately simulate an
EOP (End Of Package) event. This patch uses a timer to simulate the
hardware EOP event. The timer should only complete a DMA transfer once the
idle period satisfies a specified interval which is baud rate dependent.
The problem has been observed with low baud rates but could occur also
with high baud rates.
Make the DMA Rx timeout baud rate dependent and check the DMA residue count
before copying data to the TTY buffer. If the residue count remains
unchanged since the last interrupt, that indicates no new data was
received. In this case, the DMA should complete as an EOP event. Otherwise,
new data was received during the interval and the EOP condition is not met
so restart the DMA Rx timeout
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230510203359.1353469-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of tty/serial driver updates for 6.4-rc1.
Nothing major, just lots of tiny, constant, forward development. This
includes:
- obligatory n_gsm updates and feature additions
- 8250_em driver updates
- sh-sci driver updates
- dts cleanups and updates
- general cleanups and improvements by Ilpo and Jiri
- other small serial driver core fixes and driver updates
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEqB7w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylQuwCgwU9bGoihDtFsoFYUra/FKPPoC88Anj6t1a1f
X5HZmADnwrFNNq/jP4vH
=FeNF
-----END PGP SIGNATURE-----
Merge tag 'tty-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty/serial driver updates for 6.4-rc1.
Nothing major, just lots of tiny, constant, forward development. This
includes:
- obligatory n_gsm updates and feature additions
- 8250_em driver updates
- sh-sci driver updates
- dts cleanups and updates
- general cleanups and improvements by Ilpo and Jiri
- other small serial driver core fixes and driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (87 commits)
n_gsm: Use array_index_nospec() with index that comes from userspace
tty: vt: drop checks for undefined VT_SINGLE_DRIVER
tty: vt: distribute EXPORT_SYMBOL()
tty: vt: simplify some cases in tioclinux()
tty: vt: reformat tioclinux()
tty: serial: sh-sci: Fix end of transmission on SCI
tty: serial: sh-sci: Add support for tx end interrupt handling
tty: serial: sh-sci: Fix TE setting on SCI IP
tty: serial: sh-sci: Add RZ/G2L SCIFA DMA rx support
tty: serial: sh-sci: Add RZ/G2L SCIFA DMA tx support
serial: max310x: fix IO data corruption in batched operations
serial: core: Disable uart_start() on uart_remove_one_port()
serial: 8250: Reinit port->pm on port specific driver unbind
serial: 8250: Add missing wakeup event reporting
tty: serial: fsl_lpuart: use UARTMODIR register bits for lpuart32 platform
tty: serial: fsl_lpuart: adjust buffer length to the intended size
serial: fix TIOCSRS485 locking
serial: make SiFive serial drivers depend on ARCH_ symbols
tty: synclink_gt: don't allocate and pass dummy flags
tty: serial: simplify qcom_geni_serial_send_chunk_fifo()
...
Merge ACPI bus type driver changes, ACPI backlight driver updates and a
series of cleanups related to of.h for 6.4-rc1:
- Ensure that ACPI notify handlers are not running after removal and
clean up code in acpi_sb_notify() (Rafael Wysocki).
- Remove register_backlight_delay module option and code and remove
quirks for false-positive backlight control support advertised on
desktop boards (Hans de Goede).
- Replace irqdomain.h include with struct declarations in ACPI headers
and update several pieces of code previously including of.h
implicitly through those headers (Rob Herring).
* acpi-bus:
ACPI: bus: Ensure that notify handlers are not running after removal
ACPI: bus: Add missing braces to acpi_sb_notify()
* acpi-video:
ACPI: video: Remove desktops without backlight DMI quirks
ACPI: video: Remove register_backlight_delay module option and code
* acpi-misc:
ACPI: Replace irqdomain.h include with struct declarations
fpga: lattice-sysconfig-spi: Add explicit include for of.h
tpm: atmel: Add explicit include for of.h
virtio-mmio: Add explicit include for of.h
pata: ixp4xx: Add explicit include for of.h
ata: pata_macio: Add explicit include of irqdomain.h
serial: 8250_tegra: Add explicit include for of.h
net: rfkill-gpio: Add explicit include for of.h
staging: iio: resolver: ad2s1210: Add explicit include for of.h
iio: adc: ad7292: Add explicit include for of.h
We need to set TE to "0" (i.e., disable serial transmission) to
get the expected behavior of the end of serial transmission.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-6-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section
23.3.7 Serial Data Transmission (Asynchronous Mode), it is mentioned
that, set the SCR.TIE bit to 0 and SCR.TEIE bit to 1, after the last
data to be transmitted are written to the TDR.
This will generate tx end interrupt and in the handler set SCR.TE and
SCR.TEIE to 0.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section
23.3.7 Serial Data Transmission (Asynchronous Mode) it is mentioned
that the TE (transmit enable) must be set after setting TIE (transmit
interrupt enable) or these 2 bits are set to 1 simultaneously by a
single instruction. So set these 2 bits in single instruction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-4-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked. Similarly clearing DMARS register makes signal to work as
interrupt signal and subsequent interrupt requests to the interrupt
controller are unmasked.
Add SCIFA DMA rx support for RZ/G2L alike SoCs by disabling RXI line
interrupt and setting DMARS registers by DMA api for DMA transfer request.
Apart from this, we must set FIFO trigger to 1 for the expected behavior
of the receive transmission.
While at it replace the parameter irq to s->irqs[SCIx_RXI_IRQ] in
disable_irq_nosync() to match enable_irq() in sci_dma_rx_reenable_irq().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked. Similarly clearing DMARS register makes signal to work as
interrupt signal and subsequent interrupt requests to the interrupt
controller are unmasked.
Add SCIFA DMA tx support for RZ/G2L alike SoCs by disabling TXI line
interrupt and setting DMARS registers by DMA api for DMA transfer request.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After upgrading from 5.16 to 6.1, our board with a MAX14830 started
producing lots of garbage data over UART. Bisection pointed out commit
285e76fc04 as the culprit. That patch tried to replace hand-written
code which I added in 2b4bac48c1 ("serial: max310x: Use batched reads
when reasonably safe") with the generic regmap infrastructure for
batched operations.
Unfortunately, the `regmap_raw_read` and `regmap_raw_write` which were
used are actually functions which perform IO over *multiple* registers.
That's not what is needed for accessing these Tx/Rx FIFOs; the
appropriate functions are the `_noinc_` versions, not the `_raw_` ones.
Fix this regression by using `regmap_noinc_read()` and
`regmap_noinc_write()` along with the necessary `regmap_config` setup;
with this patch in place, our board communicates happily again. Since
our board uses SPI for talking to this chip, the I2C part is completely
untested.
Fixes: 285e76fc04 ("serial: max310x: use regmap methods for SPI batch operations")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/79db8e82aadb0e174bc82b9996423c3503c8fb37.1680732084.git.jan.kundrat@cesnet.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While rebinding a uart device in a loop I noticed we may see a tx related
race on uart_remove_one_port():
uart_write from n_tty_write
n_tty_write from file_tty_write.constprop.0
file_tty_write.constprop.0 from vfs_write
vfs_write from ksys_write
ksys_write from ret_fast_syscall
Let's disallow tx on port->UPF_DEAD. This flag gets set before we start
tearing down the port in uart_remove_one_port().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230419115423.59957-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we unbind a serial port hardware specific 8250 driver, the generic
serial8250 driver takes over the port. After that we see an oops about 10
seconds later. This can produce the following at least on some TI SoCs:
Unhandled fault: imprecise external abort (0x1406)
Internal error: : 1406 [#1] SMP ARM
Turns out that we may still have the serial port hardware specific driver
port->pm in use, and serial8250_pm() tries to call it after the port
specific driver is gone:
serial8250_pm [8250_base] from uart_change_pm+0x54/0x8c [serial_base]
uart_change_pm [serial_base] from uart_hangup+0x154/0x198 [serial_base]
uart_hangup [serial_base] from __tty_hangup.part.0+0x328/0x37c
__tty_hangup.part.0 from disassociate_ctty+0x154/0x20c
disassociate_ctty from do_exit+0x744/0xaac
do_exit from do_group_exit+0x40/0x8c
do_group_exit from __wake_up_parent+0x0/0x1c
Let's fix the issue by calling serial8250_set_defaults() in
serial8250_unregister_port(). This will set the port back to using
the serial8250 default functions, and sets the port->pm to point to
serial8250_pm.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230418101407.12403-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An 8250 UART configured as a wake-up source would not have reported
itself through sysfs as being the source of wake-up, correct that.
Fixes: b3b708fa27 ("wake up from a serial port")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230414170241.2016255-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For lpuart32 platforms, UARTMODIR register is used instead of UARTMODEM.
So here should configure the corresponding UARTMODIR register bits to
avoid confusion.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230414022111.20896-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the fls function definition provided below, we should not
subtract 1 to obtain the correct buffer length:
fls(0) = 0, fls(1) = 1, fls(0x80000000) = 32.
Fixes: 5887ad43ee ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20230410195555.1003900-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RS485 multipoint addressing support for some reason added a new
ADDRB termios cflag which is (only!) updated from one of the RS485
ioctls.
Make sure to take the termios rw semaphore for the right ioctl (i.e.
set, not get).
Fixes: ae50bb2752 ("serial: take termios_rwsem for ->rs485_config() & pass termios as param")
Cc: stable@vger.kernel.org # 6.0
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20230412124811.11217-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the
use of such symbols on other architectures, convert the SiFive serial
driver Kconfig entries from the SOC_ symbols to ARCH_ instead.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230406-carnival-aspirate-fcf69a30078c@spud
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* use memcpy() instead of the loop (removes c variable)
* use remaining parameter directly (removes chunk variable)
The code is simpler and easier to follow.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230420093514.13055-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With linux/acpi.h no longer implicitly including of.h, add an explicit
include of of.h to fix the following error:
drivers/tty/serial/8250/8250_tegra.c:68:15: error: implicit declaration of function 'of_alias_get_id' [-Werror=implicit-function-declaration]
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
SCI IP on RZ/G2L alike SoCs do not need regshift compared to other SCI
IPs on the SH platform. Currently, it does regshift and configuring Rx
wrongly. Drop adding regshift for RZ/G2L alike SoCs.
Fixes: dfc80387ae ("serial: sh-sci: Compute the regshift value for SCI ports")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230321114753.75038-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For serdev framework, tty->dev is a NULL pointer, lpuart_uport_is_active
calling device_may_wakeup() may cause kernel NULL pointer crash, so here
add the NULL pointer check before using it.
Fixes: 4f5cb8c5e9 ("tty: serial: fsl_lpuart: enable wakeup source for lpuart")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230323110923.24581-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to avoid
checking for transmission complete when UARTCTRL_SBK is asserted,
otherwise the lpuart32_tx_empty may never get TIOCSER_TEMT.
Commit 2411fd94ceaa("tty: serial: fsl_lpuart: skip waiting for
transmission complete when UARTCTRL_SBK is asserted") only fix it in
lpuart32_set_termios(), here also fix it in lpuart32_tx_empty().
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230323054415.20363-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede reported Bluetooth adapters (HCIs) connected over an UART
connection failed due corrupted Rx payload. The problem was narrowed
down to DMA Rx starting on UART_IIR_THRI interrupt. The problem occurs
despite LSR having DR bit set, which is precondition for attempting to
start DMA Rx in the first place.
From a debug patch:
[x.807834] 8250irq: iir=cc lsr+saved=60 received=0/15 ier=0f dma_t/rx/err=0/0/0
[x.808676] 8250irq: iir=c2 lsr+saved=61 received=0/0 ier=0f dma_t/rx/err=0/0/0
[x.808776] 8250irq: iir=cc lsr+saved=60 received=1/12 ier=0d dma_t/rx/err=0/1/0
[x.808870] Bluetooth: hci0: Frame reassembly failed (-84)
In the debug snippet, received field indicates 1 byte was transferred
over DMA and 12 bytes after that with the non-DMA Rx. The sole byte DMA
handled was corrupted (gets zeroed) which leads to the HCI failure.
This problem became apparent after commit e8ffbb71f7 ("serial: 8250:
use THRE & __stop_tx also with DMA") changed Tx stop behavior. Tx stop
is now triggered from a THRI interrupt.
Despite that this problem looks like a HW bug, this fix is not adding
UART_BUG_xx flag to the driver beucase it seems useful in general to
avoid starting DMA when there are only a few bytes to transfer.
Skipping DMA for small transfers avoids the extra overhead DMA incurs.
Thus, don't setup DMA Rx on UART_IIR_THRI but leave it to a subsequent
interrupt which has Rx a related IIR value.
By returning false from handle_rx_dma(), the DMA vs non-DMA decision is
postponed until either UART_IIR_RDI (FIFO threshold worth of bytes
awaiting) or UART_IIR_TIMEOUT (inter-character timeout) triggers at a
later time which allows better to discern whether the number of bytes
warrants starting DMA or not.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Fixes: e8ffbb71f7 ("serial: 8250: use THRE & __stop_tx also with DMA")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230317103034.12881-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fourth interrupt on SCI port is transmit end interrupt compared to
the break interrupt on other port types. So, shuffle the interrupts to fix
the transmit end interrupt handler.
Fixes: e1d0be6161 ("sh-sci: Add h8300 SCI")
Cc: stable <stable@kernel.org>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230317150403.154094-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a potential race before THRE/TEMT deasserts when DMA Tx is
starting up (or the next batch of continuous Tx is being submitted).
This can lead to misdetecting Tx empty condition.
It is entirely normal for THRE/TEMT to be set for some time after the
DMA Tx had been setup in serial8250_tx_dma(). As Tx side is definitely
not empty at that point, it seems incorrect for serial8250_tx_empty()
claim Tx is empty.
Fix the race by also checking in serial8250_tx_empty() whether there's
DMA Tx active.
Note: This fix only addresses in-kernel race mainly to make using
TCSADRAIN/FLUSH robust. Userspace can still cause other races but they
seem userspace concurrency control problems.
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230317113318.31327-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit b984d7b56d ("MIPS: sibyte: Remove unused config option
SIBYTE_BCM1x55"), an #if in the Broadcom SiByte DUART driver can be
simplified.
Simplify the prepreprocessor condition after config SIBYTE_BCM1x55 removal.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230323071053.417-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty framework can support polling console to allow operation
in situations where interrupts are turned off. Adding polling mode
support allows using KGDB over serial console,
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/20230322223956.84647-1-arend.vanspriel@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The direction field in the DMA config is deprecated. The sh-sci driver
sets {src,dst}_{addr,addr_width} based on the DMA direction and
it results in dmaengine_slave_config() failure as RZ DMAC driver
validates {src,dst}_addr_width values independent of DMA direction.
Fix this issue by passing both {src,dst}_{addr,addr_width}
values independent of DMA direction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230322074717.6057-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1ea35b3557 ("ARM: s3c: remove s3c24xx specific hacks"), allows
simplifying the whole config logic for SERIAL_SAMSUNG_UARTS, and did this
config simplification. However, it misses that SERIAL_SAMSUNG_UARTS_4's
effect was just to control SERIAL_SAMSUNG_UARTS, and with the commit's
change, the config SERIAL_SAMSUNG_UARTS_4 has no remaining effect and can
be deleted.
Remove this obsolete config SERIAL_SAMSUNG_UARTS_4.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230317071538.29366-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On sc7180 Chromebooks, I did the following:
* Didn't enable earlycon in the kernel command line.
* Didn't enable serial console in the kernel command line.
* Didn't enable an agetty or any other client of "/dev/ttyMSM0".
* Added "kgdboc=ttyMSM0" to the kernel command line.
After I did that, I tried to enter kdb with this command over an ssh
session:
echo g > /proc/sysrq-trigger
When I did that the system just hung.
Although I thought I'd tested this scenario before, I couldn't go back
and find a time when it was working. Previous testing must have relied
on either the UART acting as the kernel console or an agetty running.
It turns out to be pretty easy to fix: we can just use
qcom_geni_serial_port_setup() as the .poll_init() function. This,
together with the patch ("serial: uart_poll_init() should power on the
UART"), allows the debugger to work even if there are no other users
of the serial port.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316132027.RESEND.2.Ie678853bb101091afe78cc8c22344bf3ff3aed74@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Qualcomm devices which use the "geni" serial driver, kdb/kgdb won't
be very happy if you use it but the resources of the port haven't been
powered on. Today kdb/kgdb rely on someone else powering the port
on. This could be the normal kernel console or an agetty running.
Let's fix this to explicitly power things on when setting up a polling
driver.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316132027.RESEND.1.I106c39498d8094c6f5e7ada42c7db17aa5c64e48@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the tty/serial fixes in here and it resolves a merge conflict
with:
drivers/tty/serial/8250/8250_em.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty and serial driver fixes for 6.3-rc3 to resolve
some reported issues.
They include:
- 8250 driver Kconfig issue pointed out by you that showed up in -rc1
- qcom-geni serial driver fixes
- various 8250 driver fixes for reported problems
- fsl_lpuart driver fixes
- serdev fix for regression in -rc1
- vt.c bugfix
All have been in linux-next for over a week with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZBcinQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynIYACgjP49Xy1N6hDLZJgKxvnPLmvnhY4AoKM8CkHI
zbWudA1fBqsYLFtxNKaQ
=/Ond
-----END PGP SIGNATURE-----
Merge tag 'tty-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.3-rc3 to resolve
some reported issues.
They include:
- 8250 driver Kconfig issue pointed out by you that showed up in -rc1
- qcom-geni serial driver fixes
- various 8250 driver fixes for reported problems
- fsl_lpuart driver fixes
- serdev fix for regression in -rc1
- vt.c bugfix
All have been in linux-next for over a week with no reported problems"
* tag 'tty-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: vt: protect KD_FONT_OP_GET_TALL from unbound access
serial: qcom-geni: drop bogus uart_write_wakeup()
serial: qcom-geni: fix mapping of empty DMA buffer
serial: qcom-geni: fix DMA mapping leak on shutdown
serial: qcom-geni: fix console shutdown hang
serdev: Set fwnode for serdev devices
tty: serial: fsl_lpuart: fix race on RX DMA shutdown
serial: 8250_pci1xxxx: Disable SERIAL_8250_PCI1XXXX config by default
serial: 8250_fsl: fix handle_irq locking
serial: 8250_em: Fix UART port type
serial: 8250: ASPEED_VUART: select REGMAP instead of depending on it
tty: serial: fsl_lpuart: skip waiting for transmission complete when UARTCTRL_SBK is asserted
Revert "tty: serial: fsl_lpuart: adjust SERIAL_FSL_LPUART_CONSOLE config dependency"
The arbitration of the UART DMA is mishandled for a few
exceptional cases when probing and releasing the driver.
It is possible that the DMA register spaces are not defined in
device tree for an instance of the driver, so attempts to access
the registers in brcmuart_arbitration() would use NULL pointers.
It is also possible for the probe function to return an error
while still holding the UART DMA. This would prevent the UART
DMA from being claimed by an instance that could use it.
These errors are addressed by only releasing the UART DMA if it
is held by this instance (i.e. priv->dma_enabled == 1) and
directing early error paths in probe to this common release_dma
handling.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230309190224.687380-1-opendmb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hw_stopped in uart_change_line_settings() stores old hw_stopped, thus
rename it appropriately.
Alter logic to check first if the hw_stopped was changed, and then pick
which function to call if it was because the logic is more obvious that
way.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert hw_stopped in uart_port to bool because its more appropriate
type for how it is used.
Also convert the local variable in uart_change_line_settings() caching
old hw_stopped to bool.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_change_speed() changes more than just speed so rename it to more
generic uart_change_line_settings().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compare against B0 rather than assume B0 equals zero, which is true for
all archs but explicit B0 makes the code more obvious.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here).
drivers/tty/serial/sprd_serial.c:1242:34: error: ‘serial_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230310222957.315848-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/tty/serial/sh-sci.c:3144:34: error: ‘of_sci_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230310222957.315848-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230310144727.1545699-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230310144727.1545630-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/lkml/20221118224540.619276-572-uwe@kleine-koenig.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Drop the bogus uart_write_wakeup() from when setting up a new DMA
transfer, which does not free up any more space in the ring buffer.
Any pending writers will be woken up when the transfer completes.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that there is data in the ring buffer before trying to set up
a zero-length DMA transfer.
This specifically fixes the following warning when unmapping the empty
buffer on the sc8280xp-crd:
WARNING: CPU: 0 PID: 138 at drivers/iommu/dma-iommu.c:1046 iommu_dma_unmap_page+0xbc/0xd8
...
Call trace:
iommu_dma_unmap_page+0xbc/0xd8
dma_unmap_page_attrs+0x30/0x1c8
geni_se_tx_dma_unprep+0x28/0x38
qcom_geni_serial_isr+0x358/0x75c
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix what appears to be a copy-paste error that can lead to a leaked DMA
mapping on close() and failure to restart TX after the port is reopened.
Note that rx_dma_addr is generally NULL when
qcom_geni_serial_stop_tx_dma() is called as part of shutdown() (but
tx_dma_addr need not be).
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit added back the calls top stop tx and rx to shutdown()
which had previously been removed by commit e83766334f ("tty: serial:
qcom_geni_serial: No need to stop tx/rx on UART shutdown") in order to
be able to use kgdb after stopping the getty.
Not only did this again break kgdb, but it also broke serial consoles
more generally by hanging TX when stopping the getty during reboot.
The underlying problem has been there since the driver was first merged
and fixing it is going to be a bit involved so simply stop calling the
broken stop functions during shutdown for consoles for now.
Fixes: d8aca2f968 ("tty: serial: qcom-geni-serial: stop operations in progress at shutdown")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per RZ/V2M hardware manual(Rev.1.30 Jun, 2022), UART IP has a
restriction as mentioned below.
40.6.1 Point for Caution when Changing the Register Settings:
When changing the settings of the following registers, a PRESETn master
reset or FIFO reset + SW reset (FCR[2],FCR[1], HCR0[7]) must be input to
re-initialize them.
Target Registers: FCR, LCR, MCR, DLL, DLM, HCR0.
Add serial8250_em_reg_update() and serial8250_em_serial_out_helper() to
handle this restriction. serial8250_em_serial_out_helper() is identical to
previous serial8250_em_serial_out() except that UART_FCR macro is removed
from serial8250_em_serial_out_helper() as it is now handled by serial8250_
em_serial_out().
DLL/DLM register can be updated only by setting LCR[7]. So the
updation of LCR[7] will perform reset for DLL/DLM register changes.
EMMA mobile has the same register set as RZ/V2M and this patch is tested on
EMEV2 board. So, there is no harm in applying the same restriction here as
well as the HW manual for EMMA mobile is not updated for a long time.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-8-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART_FCR shares the same offset with UART_IIR. We cannot use UART_FCR
in serial8250_em_serial_in() as it overlaps with UART_IIR.
Define UART_FCR_EM macro with a high value to avoid overlapping
with existing UART_* register defines and define another macro
UART_FCR_EM_HW for the real offset.
Use these macros in serial8250_em_serial{_in/_out} function to
read/write FCR register.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-7-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify clk handling in probe() by replacing devm_clk_get()->devm_
clk_get_enabled(). This replaces the usage of clk_prepare_enable/clk_
disable_unprepare() in probe()/remove(). After that sclk is no
longer required in struct serial8250_em_priv and is replaced by a
local variable sclk in probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-6-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify probe() by using dev_err_probe() instead of dev_err() and
add a local variable 'dev' to replace '&pdev->dev'.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per HW manual for EMEV2 "R19UH0040EJ0400 Rev.4.00", the UART
IP found on EMMA mobile SoC is Register-compatible with the
general-purpose 16750 UART chip. Fix UART port type as 16750 and
enable 64-bytes fifo support.
Fixes: 22886ee968 ("serial8250-em: Emma Mobile UART driver V2")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amlogic Meson G12A (and later) SoCs also have the "divide XTAL by 2" bit
as the S4 UART controllers. Add a new compatible string for these SoCs
and enable the has_xtal_div2 flag for them.
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230307222651.2106615-3-martin.blumenstingl@googlemail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stm32_usart_transmit_chars() may be called with empty or stopped
transmit queue, and no XON/OFF character pending. This can happen at
the end of transmission, where this last call is used to either handle
the XON/XOFF x_char, or disable TX interrupt if queue is empty or
stopped.
If that occurs, do not assert the RS485 RTS/DE GPIO anymore, as the
GPIO would remain asserted past the end of transmission and that would
block the RS485 bus after the transmission.
Only assert the RS485 RTS/DE GPIO if there is either pending XON/XOFF
x_char, or at least one character in running transmit queue.
Fixes: d7c7671616 ("serial: stm32: Use TC interrupt to deassert GPIO RTS in RS485 mode")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230223042252.95480-2-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point in casting a struct uart_port to a struct imx_port
just to access the first member of the latter (a struct uart_port).
This introduces no code changes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230302115417.1860210-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From time to time DMA completion can come in the middle of DMA shutdown:
<process ctx>: <IRQ>:
lpuart32_shutdown()
lpuart_dma_shutdown()
del_timer_sync()
lpuart_dma_rx_complete()
lpuart_copy_rx_to_tty()
mod_timer()
lpuart_dma_rx_free()
When the timer fires a bit later, sport->dma_rx_desc is NULL:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
pc : lpuart_copy_rx_to_tty+0xcc/0x5bc
lr : lpuart_timer_func+0x1c/0x2c
Call trace:
lpuart_copy_rx_to_tty
lpuart_timer_func
call_timer_fn
__run_timers.part.0
run_timer_softirq
__do_softirq
__irq_exit_rcu
irq_exit
handle_domain_irq
gic_handle_irq
call_on_irq_stack
do_interrupt_handler
...
To fix this fold del_timer_sync() into lpuart_dma_rx_free() after
dmaengine_terminate_sync() to make sure timer will not be re-started in
lpuart_copy_rx_to_tty() <= lpuart_dma_rx_complete().
Fixes: 4a8588a1cf ("serial: fsl_lpuart: delete timer on shutdown")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20230309134302.74940-2-alexander.sverdlin@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 handle_irq callback is not just called from the interrupt
handler but also from a timer callback when polling (e.g. for ports
without an interrupt line). Consequently the callback must explicitly
disable interrupts to avoid a potential deadlock with another interrupt
in polled mode.
Fix up the two paths in the freescale callback that failed to re-enable
interrupts when polling.
Fixes: 853a9ae29e ("serial: 8250: fix handle_irq locking")
Cc: stable@vger.kernel.org # 5.13
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y/xYzqp4ogmOF5t0@kili
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230227085046.24282-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per HW manual for EMEV2 "R19UH0040EJ0400 Rev.4.00", the UART
IP found on EMMA mobile SoC is Register-compatible with the
general-purpose 16750 UART chip. Fix UART port type as 16750 and
enable 64-bytes fifo support.
Fixes: 22886ee968 ("serial8250-em: Emma Mobile UART driver V2")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: 8d310c9107 ("drivers/tty/serial/8250: Make Aspeed VUART SIRQ polarity configurable")
Cc: stable <stable@kernel.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Oskar Senft <osk@google.com>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20230226053953.4681-9-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to skip
waiting for transmission complete when UARTCTRL_SBK is asserted,
otherwise the kernel may stuck here.
And actually set_termios() adds transmission completion waiting to avoid
data loss or data breakage when changing the baud rate, but we don't
need to worry about this when queuing break characters.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230223093941.31790-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5779a072c2.
This results in a link error of
ld: drivers/tty/serial/earlycon.o: in function `parse_options':
drivers/tty/serial/earlycon.c:99: undefined reference to `uart_parse_earlycon'
When the config is in this state
CONFIG_SERIAL_CORE=m
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_EARLYCON=y
CONFIG_SERIAL_FSL_LPUART=m
CONFIG_SERIAL_FSL_LPUART_CONSOLE=y
Fixes: 5779a072c2 ("tty: serial: fsl_lpuart: adjust SERIAL_FSL_LPUART_CONSOLE config dependency")
Cc: stable <stable@kernel.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230226173846.236691-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work falls
into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be moved
into read-only memory (i.e. const) The recent work with Rust has
pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only making
things safer overall. This is the contuation of that work (started
last release with kobject changes) in moving struct bus_type to be
constant. We didn't quite make it for this release, but the
remaining patches will be finished up for the release after this
one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/ipdg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynL3gCgwzbcWu0So3piZyLiJKxsVo9C2EsAn3sZ9gN6
6oeFOjD3JDju3cQsfGgd
=Su6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/itAw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykJbQCfWv/J4ZElO108iHBU5mJCDagUDBgAnAtLLN6A
SEAnnokGCDtA/BNIXeES
=luRi
-----END PGP SIGNATURE-----
Merge tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
tty: n_gsm: add keep alive support
serial: imx: remove a redundant check
dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
tty: n_gsm: add TIOCMIWAIT support
tty: n_gsm: add RING/CD control support
tty: n_gsm: mark unusable ioctl structure fields accordingly
serial: imx: get rid of registers shadowing
serial: imx: refine local variables in rxint()
serial: imx: stop using USR2 in FIFO reading loop
serial: imx: remove redundant USR2 read from FIFO reading loop
serial: imx: do not break from FIFO reading loop prematurely
serial: imx: do not sysrq broken chars
serial: imx: work-around for hardware RX flood
serial: imx: factor-out common code to imx_uart_soft_reset()
serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
serial: 8250_pci1xxxx: Add driver for quad-uart support
serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
tty: pcn_uart: fix memory leak with using debugfs_lookup()
...
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate subsystem
trees, but the majority is in the same branch, in order to better handle
dependencies between the patches and avoid breaking bisection.
Unfortunately that leads to merge conflicts against other changes in the
subsystem trees, but they should all be trivial to resolve by removing
the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed. The
only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users.
-----BEGIN PGP SIGNATURE-----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=WejQ
-----END PGP SIGNATURE-----
Merge tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
cpp_check reports
drivers/tty/serial/imx.c:1207:15: style: Condition 'r_bytes>0' is always true [knownConditionTrueFalse]
if (r_bytes > 0) {
r_byte is set to
r_bytes = rx_ring->head - rx_ring->tail;
The head - tail calculation is also done by the earlier check
if (rx_ring->head <= sg_dma_len(sgl) &&
rx_ring->head > rx_ring->tail) {
so r_bytes will always be > 0, so the second check is not needed.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Link: https://lore.kernel.org/r/20230211154550.2130670-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move include/linux/qcom-geni-se.h to include/linux/soc/qcom/geni-se.h.
This removes 1 of a few remaining Qualcomm-specific headers into a more
approciate subdirectory under include/.
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Reviewed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Link: https://lore.kernel.org/r/20230203210133.3552796-1-quic_eberman@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neither registers shadowing is functionally needed as all the registers are
read-write, nor the shadowing makes much sense for speed-up, as most speed
critical reads/writes (of data Rx/Tx registers) are not shadowed anyway.
Moreover, the shadowing code is obviously pure overhead on the write path.
Get rid of the shadowing code and variables due to above considerations.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201141603.4205-1-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'rx' is chip register, similar to 'usr2', so let it be of 'u32' type as
well.
Move 'flg' to be FIFO read loop local as it's not used outside.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-8-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chip provides all the needed bits in the URXD0 register that we read
anyway for data, so get rid of reading USR2 and use only URXD0 bits
instead.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-7-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to read USR2 twice at every loop iteration: get rid of the
second read.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-6-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to prematurely break out of FIFO reading loop, and it
might cause needless reenters into ISR, so keep reading until FIFO is
empty.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-5-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not call uart_handle_sysrq_char() if we got any receive error along with
the character, as we don't want random junk to be considered a sysrq.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-4-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check if hardware Rx flood is in progress, and issue soft reset to UART to
stop the flood.
A way to reproduce the flood (checked on iMX6SX) is: open iMX UART at 9600
8N1, and from external source send 0xf0 char at 115200 8N1. In about 90% of
cases this starts a flood of "receiving" of 0xff characters by the iMX UART
that is terminated by any activity on RxD line, or could be stopped by
issuing soft reset to the UART (just stop/start of RX does not help). Note
that in essence what we did here is sending isolated start bit about 2.4
times shorter than it is to be if issued on the UART configured baud rate.
There was earlier attempt to fix similar issue in: 'commit
b38cb7d257 ("serial: imx: Disable new features of autobaud detection")',
but apparently it only gets harder to reproduce the issue after that
commit.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-3-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We perform soft reset in 2 places, slightly differently for no sufficient
reasons, so move more generic variant to a function, and re-use the code.
Out of 2 repeat counters, 10 and 100, select 10, as the code works at
interrupts disabled, and in practice the reset happens immediately.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-2-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx's quad-uart function has the capability to wake up UART
from suspend state. Enable wakeup before entering into suspend and
disable wakeup on resume.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-5-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx uart supports RS485 mode of operation in the hardware with
auto-direction control with configurable delay for releasing RTS after
the transmission. This patch adds support for the RS485 mode.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-4-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx is a PCIe switch with a multi-function endpoint on one of
its downstream ports. Quad-uart is one of the functions in the
multi-function endpoint. This driver loads for the quad-uart and
enumerates single or multiple instances of uart based on the PCIe
subsystem device ID.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-3-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230202141221.2293012-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There maybe pending USR interrupt before requesting irq, however
uart_add_one_port has not executed, so there will be kernel panic:
[ 0.795668] Unable to handle kernel NULL pointer dereference at virtual addre
ss 0000000000000080
[ 0.802701] Mem abort info:
[ 0.805367] ESR = 0x0000000096000004
[ 0.808950] EC = 0x25: DABT (current EL), IL = 32 bits
[ 0.814033] SET = 0, FnV = 0
[ 0.816950] EA = 0, S1PTW = 0
[ 0.819950] FSC = 0x04: level 0 translation fault
[ 0.824617] Data abort info:
[ 0.827367] ISV = 0, ISS = 0x00000004
[ 0.831033] CM = 0, WnR = 0
[ 0.833866] [0000000000000080] user address but active_mm is swapper
[ 0.839951] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[ 0.845953] Modules linked in:
[ 0.848869] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.1+g56321e101aca #1
[ 0.855617] Hardware name: Freescale i.MX8MP EVK (DT)
[ 0.860452] pstate: 000000c5 (nzcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.867117] pc : __imx_uart_rxint.constprop.0+0x11c/0x2c0
[ 0.872283] lr : imx_uart_int+0xf8/0x1ec
The issue only happends in the inmate linux when Jailhouse hypervisor
enabled. The test procedure is:
while true; do
jailhouse enable imx8mp.cell
jailhouse cell linux xxxx
sleep 10
jailhouse cell destroy 1
jailhouse disable
sleep 5
done
And during the upper test, press keys to the 2nd linux console.
When `jailhouse cell destroy 1`, the 2nd linux has no chance to put
the uart to a quiese state, so USR1/2 may has pending interrupts. Then
when `jailhosue cell linux xx` to start 2nd linux again, the issue
trigger.
In order to disable irqs before requesting them, both UCR1 and UCR2 irqs
should be disabled, so here fix that, disable the Ageing Timer interrupt
in UCR2 as UCR1 does.
Fixes: 8a61f0c70a ("serial: imx: Disable irqs before requesting them")
Suggested-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Link: https://lore.kernel.org/r/20230206013016.29352-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous 'commit 846651eca0 ("serial: fsl_lpuart: RS485 RTS
polariy is inverse")' only fixed the inverse issue on lpuart 8bit
platforms.
This is a follow-up patch to fix the RS485 polarity inverse
issue on lpuart 32bit platforms.
Fixes: 03895cf41d ("tty: serial: fsl_lpuart: Add support for RS-485")
Reported-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20230207162420.3647904-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The relevant history introducing serial_lsr_in() looks as follows:
$ git log --graph --oneline --boundary 9fafe733514b..df36f3e3fbb7 -- drivers/tty/serial/8250/8250_port.c
* df36f3e3fb Merge tag 'v5.19-rc3' into tty-next
|\
| * be03b0651f serial: 8250: Store to lsr_save_flags after lsr read
* | ...
* | bdb70c424d serial: 8250: Create serial_lsr_in()
* | ce338e4477 serial: 8250: Store to lsr_save_flags after lsr read
* | ...
|/
o 9fafe73351 tty: remove CMSPAR ifdefs
So the patch "serial: 8250: Store to lsr_save_flags after lsr read" was
introduced twice and in one branch it was followed up by commit
bdb70c424d ("serial: 8250: Create serial_lsr_in()") which moved
explicit lsr_saved_flags handling into a new function serial_lsr_in().
When the two branches were merged in commit df36f3e3fb, we got both,
serial_lsr_in() and the explicit lsr_saved_flags handling.
So drop the explicit lsr_saved_flags handling.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230202104501.264686-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As DMA Rx can be completed from two places, it is possible that DMA Rx
completes before DMA completion callback had a chance to complete it.
Once the previous DMA Rx has been completed, a new one can be started
on the next UART interrupt. The following race is possible
(uart_unlock_and_check_sysrq_irqrestore() replaced with
spin_unlock_irqrestore() for simplicity/clarity):
CPU0 CPU1
dma_rx_complete()
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma_flush()
__dma_rx_complete()
dma->rx_running = 0
// Complete DMA Rx
spin_unlock_irqrestore(&port->lock)
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma()
dma->rx_running = 1
// Setup a new DMA Rx
spin_unlock_irqrestore(&port->lock)
spin_lock_irqsave(&port->lock)
// sees dma->rx_running = 1
__dma_rx_complete()
dma->rx_running = 0
// Incorrectly complete
// running DMA Rx
This race seems somewhat theoretical to occur for real but handle it
correctly regardless. Check what is the DMA status before complething
anything in __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__dma_rx_complete() is called from two places:
- Through the DMA completion callback dma_rx_complete()
- From serial8250_rx_dma_flush() after IIR_RLSI or IIR_RX_TIMEOUT
The former does not hold port's lock during __dma_rx_complete() which
allows these two to race and potentially insert the same data twice.
Extend port's lock coverage in dma_rx_complete() to prevent the race
and check if the DMA Rx is still pending completion before calling
into __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting an interrupt with IRQF_ONESHOT will run the primary handler
in the hard-IRQ context even in the force-threaded mode. The
force-threaded mode is used by PREEMPT_RT in order to avoid acquiring
sleeping locks (spinlock_t) in hard-IRQ context. This combination
makes it impossible and leads to "sleeping while atomic" warnings.
Use one interrupt handler for both handlers (primary and secondary)
and drop the IRQF_ONESHOT flag which is not needed.
Fixes: e359b4411c ("serial: stm32: fix threaded interrupt handling")
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Valentin Caron <valentin.caron@foss.st.com> # V3
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230120160332.57930-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct liteuart_port keeps tracking of UART ID which is also
saved in the struct uart_port as line member. Drop the former one
and use the latter everywhere.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20230123192604.81452-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe we need to call all devm_*() first followed by
non-devm_*() calls. This is due to reversed clean up that
may happen in a wrong order otherwise. The driver currently
allocates xarray before calling
devm_platform_get_and_ioremap_resource(). While it's not an
issue in this certain case, it's still better to be pedantic.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gabriel Somlo <somlo@cmu.edu>
Link: https://lore.kernel.org/r/20230123191741.79751-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lpuart of imx8ulp is basically the same as imx7ulp, but it supports
some new features based on imx7ulp, such as it can assert the DMA
request on EOP(end-of-packet).
Here add lpuart support for imx8ulp, and rx_watermark is set to 3 as
imx8ulp RX FIFO depth is 8.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-7-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RTS watermark support for LPUART. The RX RTS_B output negates when
the number of empty words in the receive FIFO is greater or equal to
RTSWATER. Here set the RTSWATER to half of the rxfifo_size.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-6-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the growth of rx watermark, it's useful to enable the Receiver Idle
Empty function, it can assert the RDRF(Receive Data Register Full Flag)
when the receiver is idle for a number of idle characters and the FIFO
is not empty. It will generate a DMA request or interrupt, which can
avoid receive data being trapped in the RX FIFO since the number of
words received is less than the watermark.
Here set the RXIDEN as 0x3 which enable the RDRF assertion due to
partially filled FIFO when receiver is idle for 4 characters.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-5-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RXWATER value must be greater than 0 according to the LPUART
reference manual. And when the number of datawords in the receive
FIFO is greater than RXWATER, an interrupt or a DMA request is
generated, so no need to set the different value for lpuart interrupt
case and dma case. Here delete the wrong RXWATER setting for dma case
directly.
Fixes: 42b68768e5 ("serial: fsl_lpuart: DMA support for 32-bit variant")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since imx8qxp RX FIFO depth is 64 datawords, it will be better to set
the rx watermark as 31, which means when the number of datawords in the
receive FIFO(>= 32) is greater than the watermark, an interrupt or a DMA
request is generated.
Also keep the console rx watermark as 1 to make sure it responsive.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add rx_watermark parameter for struct lpuart_port to make the receive
watermark configurable for different platforms.
No function changed.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lpuart32_setup_watermark_enable() will configure the UART FIFO and
watermark, also enable the receiver and transmitter, this should be done
after the rx/tx dma steup ready.
Also add lpuart32_hw_disable() to make sure the receiver/transmitter and
interrupts are disabled during the dma steup.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130054107.9119-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Goto to the correct rollback label instead of directly returning.
Fixes: 5602cf99dc ("serial: liteuart: add IRQ support for the RX path")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20230123173857.40695-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for
serial engine DMA") renamed rx_fifo member to rf_buf which caused a
build failure when b8caf69a69 ("tty: serial: qcom-geni-serial: fix
slab-out-of-bounds on RX FIFO buffer") from tty-linus was merged into
tty-next.
Fix the member variable name.
Fixes: 7a6aa989f2 ("Merge 6.2-rc5 into tty-next")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230123173857.40695-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty and serial driver fixes for 6.2-rc5 that resolve
a number of tiny reported issues and some new device ids. They include:
- new device id for the exar serial driver
- speakup tty driver bugfix
- atmel serial driver baudrate fixup
- stm32 serial driver bugfix and then revert as the bugfix broke the
build. That will come back in a later pull request once it is all
worked out properly.
- amba-pl011 serial driver rs486 mode bugfix
- qcom_geni serial driver bugfix
Most of these have been in linux-next with no reported problems (well,
other than the build breakage which generated the revert), the new
device id passed 0-day testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY8wDQA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynGegCguB+ZpDHKt9wccrGP3h/dwT2MAm8AnAqG4bmy
Yw/cHHPt9gx+AW6RBtAL
=EymN
-----END PGP SIGNATURE-----
Merge tag 'tty-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.2-rc5 that
resolve a number of tiny reported issues and some new device ids. They
include:
- new device id for the exar serial driver
- speakup tty driver bugfix
- atmel serial driver baudrate fixup
- stm32 serial driver bugfix and then revert as the bugfix broke the
build. That will come back in a later pull request once it is all
worked out properly.
- amba-pl011 serial driver rs486 mode bugfix
- qcom_geni serial driver bugfix
Most of these have been in linux-next with no reported problems (well,
other than the build breakage which generated the revert), the new
device id passed 0-day testing"
* tag 'tty-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: exar: Add support for Sealevel 7xxxC serial cards
Revert "serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler"
tty: serial: qcom_geni: avoid duplicate struct member init
serial: atmel: fix incorrect baudrate setup
tty: fix possible null-ptr-defer in spk_ttyio_release
serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler
serial: amba-pl011: fix high priority character transmission in rs486 mode
serial: pch_uart: Pass correct sg to dma_unmap_sg()
tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer
Add support for Sealevel 7xxxC serial cards.
This patch:
* Adds IDs to recognize 7xxxC cards from Sealevel Systems.
* Updates exar_pci_probe() to set nr_ports to last two bytes of primary
dev ID for these cards.
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2301191440010.22558@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
