Both Alpine Ridge and Titan Ridge require special flows in order to
activate the internal xHCI controller when there is USB device connected
to the downstream type-C port. This implements the missing flows for
both.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
tb_switch_is_alpine_ridge() is missing device ID for Intel Alpine Ridge
dual port version so add this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Titan Ridge does not disable AUX timers when it gets SET_CONFIG
with SET_LTTPR_MODE set which makes DP tunneling to fail. For this
reason disable LTTPR on Titan Ridge device side.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
While at it, include directly <linux/dma-mapping.h> instead on relying on
indirect inclusion.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add a module parameter that allows user to completely disable CLx
functionality in case problems are found.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Low power link states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle. The
simplest one being called CL0s. Follow what we already do for USB4
device routers and enable CL0s for Intel Titan Ridge device router too.
This allows better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Rename the VSC capability: TB_VSE_CAP_IECS to TB_VSE_CAP_CP_LP to follow
the Intel devices namings as appear in the datasheet. This capability
is used for controlling CLx (Low Power states of the link).
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Titan Ridge based routers have slightly different flow for time
disruption than USB4 compliant routers. This makes it work on Titan
Ridge too. Needed to enable link low power states on Titan Ridge.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently usb4_switch_wait_for_bit() used only in usb4.c Moving to
switch.c to call it from other files. Also change the prefix to "tb_"
to follow to the naming convention.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In this patch we add enabling of CL0s - a low power state of the link.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle. For now,
we add support only for first low power state: CL0s. We enable it, if
both sides of the link support it, and only for the first hop router.
(i.e. the first device that connected to the host router). This is
needed for better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Up until Titan Ridge (Thunderbolt 3) device routers only supported
bi-directional mode. In this patch we add to TMU a uni-directional mode.
The uni-directional mode is needed for enabling of low power state of
the link (CLx).
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
kmemdup() may return NULL if there is not enough memory available. Check
this and bail out early in this case. While there move INIT_WORK() to
happen after we have allocated all the memory needed for the event
handling to avoid doing unnecessary work.
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to make the underneath API easier to change in the future,
prevent users from dereferencing fwnode from struct device.
Instead, use the specific dev_fwnode() API for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
These fields are marked read-only for USB4 routers so do not touch them
in that case. Update the kernel-doc of tb_dp_port_set_hops() to reflect
this too.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This might happen if the boot firmware uses different amount of NFC
credits than what the router suggests, or we are dealing with pre-USB4
device.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Sometimes when plugging in a USB4 device we might see following error:
thunderbolt 1-0:3.1: runtime PM trying to activate child device 1-0:3.1 but parent (usb4_port3) is not active
This happens because the parent USB4 port was still runtime suspended.
Fix this by runtime resuming the USB4 port before scanning the retimers
below it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the boot firmware implements connection manager of its own it may not
create the paths in the same way or order we do. For example it may
create first PCIe tunnel and then USB3 tunnel. When we restore our
tunnels (first de-activating them) we may be doing that over completely
different tunnels and that leaves them possibly non-functional. For this
reason we re-use the tunnel discovery functionality and find out all the
existing tunnels, and tear them down. Once that is done we can restore
our tunnels.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If protocol tunnels are already up when the driver is loaded, for
instance if the boot firmware implements connection manager of its own,
runtime PM reference count of the consumer devices behind the tunnel
might have been increased already before the device link is created but
the supplier device runtime PM reference count is not. This leads to a
situation where the supplier (the Thunderbolt driver) can runtime
suspend even if it should not because the corresponding protocol tunnel
needs to be up causing the devices to be removed from the corresponding
native bus.
Prevent this from happening by making both sides of the link runtime PM
active briefly. The pm_runtime_put() for the consumer (PCIe
root/downstream port, xHCI) then allows it to runtime suspend again but
keeps the supplier runtime resumed the whole time it is runtime active.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
tb_xdp_properties_changed_request() was calling tb_xdp_handle_error() with
a struct tb_xdp_properties_changed_response on the stack, which does not
have the "error" field present when cast to struct tb_xdp_error_response.
This was detected when building with -Warray-bounds:
drivers/thunderbolt/xdomain.c: In function 'tb_xdomain_properties_changed':
drivers/thunderbolt/xdomain.c:226:22: error: array subscript 'const struct tb_xdp_error_response[0]' is partly outside array bounds of 'struct tb_xdp_properties_changed_response[1]' [-Werror=array-bounds]
226 | switch (error->error) {
| ~~~~~^~~~~~~
drivers/thunderbolt/xdomain.c:448:51: note: while referencing 'res'
448 | struct tb_xdp_properties_changed_response res;
| ^~~
Add union containing struct tb_xdp_error_response to structures passed
to tb_xdp_handle_error(), so that the "error" field will be present.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This includes following Thunderbolt/USB4 changes for the v5.16 merge
window:
* Re-enable retry logic for control packets in domain needed by some
controllers when software connection manager is being used
* Fix -Wrestrict build warning emitted by gcc-11.
Both have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=xKvr
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.16 merge window
This includes following Thunderbolt/USB4 changes for the v5.16 merge
window:
* Re-enable retry logic for control packets in domain needed by some
controllers when software connection manager is being used
* Fix -Wrestrict build warning emitted by gcc-11.
Both have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Fix -Wrestrict warning
thunderbolt: Enable retry logic for intra-domain control packets
The structleak plugin causes the stack frame size to grow immensely when
used with KUnit:
drivers/thunderbolt/test.c:1529:1: error: the frame size of 1176 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Turn it off in this file.
Linus already split up tests in this file, so this change *should* be
redundant now.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
gcc-11 warns when building with W=1:
drivers/thunderbolt/xdomain.c: In function 'modalias_show':
drivers/thunderbolt/xdomain.c:733:16: error: 'sprintf' argument 3 overlaps destination object 'buf' [-Werror=restrict]
733 | return sprintf(buf, "%s\n", buf);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/thunderbolt/xdomain.c:727:36: note: destination object referenced by 'restrict'-qualified argument 1 was declared here
727 | char *buf)
| ~~~~~~^~~
There is no need for the sprintf() here when a strcat() does
the same thing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In case of software connection manager, the response packets are lost
sometimes within the stipulated time. Hence resending the control
packets in such scenario by increasing the retry count TB_CTL_RETRIES
value.
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The tb_test_credit_alloc_all() function had a huge number of
KUNIT_ASSERT() statements, all of which (though the magic of many many
layers of inscrutable macros) ended up allocating and initializing
various test assertion structures on the stack.
Don't do that. The kernel stack isn't infinite, and we have compiler
warnings (now errors) for the case where a stack frame grows too large.
Like it did here, by not an inconsiderable margin:
drivers/thunderbolt/test.c: In function ‘tb_test_credit_alloc_all’:
drivers/thunderbolt/test.c:2367:1: error: the frame size of 4500 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
2367 | }
| ^
Solve this similarly to the lib/test_scanf case: split out the tests
into several smaller functions, each just testing one particular tunnel
credit allocation.
This makes the i386 allyesconfig build work for me again.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big set of USB and Thunderbolt patches for 5.15-rc1.
Nothing huge in here, just lots of constant forward progress on a number
of different drivers and hardware support:
- more USB 4/Thunderbolt support added
- dwc3 driver updates and additions
- usb gadget fixes and addtions for new types
- udc gadget driver updates
- host controller updates
- removal of obsolete drivers
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS9+Tw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymqyQCgxWjp4VD9Ycbz1XsHRIkkERWj6WgAnRe4mCpG
n5csYXATbYUD0UdH0hru
=xZCV
-----END PGP SIGNATURE-----
Merge tag 'usb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.15-rc1.
Nothing huge in here, just lots of constant forward progress on a
number of different drivers and hardware support:
- more USB 4/Thunderbolt support added
- dwc3 driver updates and additions
- usb gadget fixes and addtions for new types
- udc gadget driver updates
- host controller updates
- removal of obsolete drivers
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (148 commits)
usb: isp1760: otg control register access
usb: isp1760: use the right irq status bit
usb: isp1760: write to status and address register
usb: isp1760: fix qtd fill length
usb: isp1760: fix memory pool initialization
usb: typec: tcpm: Fix spelling mistake "atleast" -> "at least"
usb: dwc2: Fix spelling mistake "was't" -> "wasn't"
usb: renesas_usbhs: Fix spelling mistake "faile" -> "failed"
usb: host: xhci-rcar: Don't reload firmware after the completion
usb: xhci-mtk: allow bandwidth table rollover
usb: mtu3: fix random remote wakeup
usb: mtu3: return successful suspend status
usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint
usb: xhci-mtk: modify the SOF/ITP interval for mt8195
usb: xhci-mtk: add a member of num_esit
usb: xhci-mtk: check boundary before check tt
usb: xhci-mtk: update fs bus bandwidth by bw_budget_table
usb: xhci-mtk: fix issue of out-of-bounds array access
usb: xhci-mtk: support option to disable usb2 ports
usb: xhci-mtk: fix use-after-free of mtk->hcd
...
This includes following Thunderbolt/USB4 changes for the v5.15 merge
window:
* Include authorized value in the KOBJ_CHANGE event of a device router
* A couple of improvements to get the driver working also with the AMD
USB4 host controller.
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iQJUBAABCgA+FiEEVTdhRGBbNzLrSUBaAP2fSd+ZWKAFAmEkzz8gHG1pa2Eud2Vz
dGVyYmVyZ0BsaW51eC5pbnRlbC5jb20ACgkQAP2fSd+ZWKCU1hAAiyvLKqFBsgye
y8Zp6aeKkIjZ8wqnM0q97ba+cq23T/NwGsgSVDPLJesZc2hJPbAQIf0Iy3BKFjL3
G5feynsWxLhHqnOsY3tL7iw1lUJoreeagPycZ5Bj4xkVDEsCbvyGnDCrlLsO4MzP
Ia9zFN6kHyLGEmk0DROM1lAWZiAf7gIL6XW+mU2KDCYYaTcgQE2Im199yr3oqgi/
8y4VsYkHolg3r0DtiwKBa5jFZ+iiCJJqAjz8+Yh12bjB0+dSBlxJWSpeH/fsDPwq
FqMX6lMZuQPd71dlBOAIFr8RHjEg0owX8HUyxVb9MLoufhLFf0MIS/uKYRRfxTIH
zcTf8LOmZIM8FUqtsnXT3nO7rdCz2YWUmmjPLkYX2Ssi1XoxWvkeWBfKmZyXHiKB
uWwaHc3+uLSJSMvMqSLCTG6pK24Ux8C0LELoun4cj6CVi7018yLp+JiYAIn/QSoI
QFIXg9EKC2WOXo539LxlkNVDnLumVhc3e/Sg+ykq8KVj++AfMbZzaOpvyhuDs9cj
PHfSybRpC0+Q6RUMhazxjiMs2u8uRYkfp4kS6htg1MrxGcEbvv/22y0TuKl3D/nr
pBEZGELgvnMd69TuhFP9yM4504P6BFaoQCDy9XhReeUTbRnmBBMDG5uSAoj/+gbe
od3B0YhSIjujKBewMeXh689+30DYtqQ=
=1bPR
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.15 merge window
This includes following Thunderbolt/USB4 changes for the v5.15 merge
window:
* Include authorized value in the KOBJ_CHANGE event of a device router
* A couple of improvements to get the driver working also with the AMD
USB4 host controller.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Fix port linking by checking all adapters
thunderbolt: Do not read control adapter config space
thunderbolt: Handle ring interrupt by reading interrupt status register
thunderbolt: Add vendor specific NHI quirk for auto-clearing interrupt status
thunderbolt: Add authorized value to the KOBJ_CHANGE uevent
In tb_switch_default_link_ports(), while linking of ports,
only odd-numbered ports (1,3,5..) are considered and even-numbered
ports are not considered.
AMD host router has lane adapters at 2 and 3 and link ports at adapter 2
is not considered due to which lane bonding gets disabled.
Hence added a fix such that all ports are considered during
linking of ports.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Adapter 0 is the control adapter and as per USB4 spec in section 2.2.6.2
control Adapters do not have an adapter configuration space.
For this reason skip reading adapter config space in tb_port_init() when
the port number is 0. This actually simplifies the rest of the function
as we don't need to check for the port->port == 0 anymore.
While there drop the extra empty line at the end of the function.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
As per USB4 specification by default "Disable ISR Auto-Clear" bit is set
to zero and the Tx/Rx ring interrupt status needs to be cleared.
Hence handle it by reading the interrupt status register (ISR) in the
MSI-X handler.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Introduce nhi_check_quirks() routine to handle any vendor specific quirks
to manage a hardware specific implementation.
On Intel hardware the USB4 controller supports clearing the interrupt
status register automatically right after it is being issued. For this
reason add a new quirk that does that on all Intel hardware.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For security reasons, we would like to monitor and track when the
Thunderbolt devices are authorized and deauthorized (i.e. when the
Thunderbolt sysfs "authorized" attribute changes). Currently the
userspace gets a udev change notification when there is a change, but
the state may have changed (again) by the time we look at the authorized
attribute in sysfs. So an authorization event may go unnoticed. Thus
make it easier by informing the actual change (new value of authorized
attribute) in the udev change notification.
The change is included as a key value "authorized=<val>" where <val>
is the new value of sysfs attribute "authorized", and is described at
Documentation/ABI/testing/sysfs-bus-thunderbolt under
/sys/bus/thunderbolt/devices/.../authorized.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.
This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.
With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.
Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM3EA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynGewCeMg7YvtCnqFBNebC+GfKpFTgWxO4AnAppjSrZ
RPGQgfZdWmx7daCXWbSK
=u68a
-----END PGP SIGNATURE-----
Merge tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
phy: qcom-qusb2: Add configuration for SM4250 and SM6115
dt-bindings: phy: qcom,qusb2: document sm4250/6115 compatible
dt-bindings: usb: qcom,dwc3: Add bindings for sm6115/4250
USB: cdc-acm: blacklist Heimann USB Appset device
usb: xhci-mtk: allow multiple Start-Split in a microframe
usb: ftdi-elan: remove redundant continue statement in a while-loop
usb: class: cdc-wdm: return the correct errno code
xhci: remove redundant continue statement
usb: dwc3: Fix debugfs creation flow
usb: gadget: hid: fix error return code in hid_bind()
usb: gadget: eem: fix echo command packet response issue
usb: gadget: f_hid: fix endianness issue with descriptors
Revert "USB: misc: Add onboard_usb_hub driver"
Revert "of/platform: Add stubs for of_platform_device_create/destroy()"
Revert "usb: host: xhci-plat: Create platform device for onboard hubs in probe()"
Revert "arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub"
xhci: solve a double free problem while doing s4
xhci: handle failed buffer copy to URB sg list and fix a W=1 copiler warning
xhci: Add adaptive interrupt rate for isoch TRBs with XHCI_AVOID_BEI quirk
xhci: Remove unused defines for ERST_SIZE and ERST_ENTRIES
...
This KUnit update for Linux 5.14-rc1 consists of fixes and features:
-- add support for skipped tests
-- introduce kunit_kmalloc_array/kunit_kcalloc() helpers
-- add gnu_printf specifiers
-- add kunit_shutdown
-- add unit test for filtering suites by names
-- convert lib/test_list_sort.c to use KUnit
-- code organization moving default config to tools/testing/kunit
-- refactor of internal parser input handling
-- cleanups and updates to documentation
-- code cleanup related to casts
-----BEGIN PGP SIGNATURE-----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=5QAv
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit update from Shuah Khan:
"Fixes and features:
- add support for skipped tests
- introduce kunit_kmalloc_array/kunit_kcalloc() helpers
- add gnu_printf specifiers
- add kunit_shutdown
- add unit test for filtering suites by names
- convert lib/test_list_sort.c to use KUnit
- code organization moving default config to tools/testing/kunit
- refactor of internal parser input handling
- cleanups and updates to documentation
- code cleanup related to casts"
* tag 'linux-kselftest-kunit-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
kunit: add unit test for filtering suites by names
kasan: test: make use of kunit_skip()
kunit: test: Add example tests which are always skipped
kunit: tool: Support skipped tests in kunit_tool
kunit: Support skipped tests
thunderbolt: test: Reinstate a few casts of bitfields
kunit: tool: internal refactor of parser input handling
lib/test: convert lib/test_list_sort.c to use KUnit
kunit: introduce kunit_kmalloc_array/kunit_kcalloc() helpers
kunit: Remove the unused all_tests.config
kunit: Move default config from arch/um -> tools/testing/kunit
kunit: arch/um/configs: Enable KUNIT_ALL_TESTS by default
kunit: Add gnu_printf specifiers
lib/cmdline_kunit: Remove a cast which are no-longer required
kernel/sysctl-test: Remove some casts which are no-longer required
thunderbolt: test: Remove some casts which are no longer required
mmc: sdhci-of-aspeed: Remove some unnecessary casts from KUnit tests
iio: Remove a cast in iio-test-format which is no longer required
device property: Remove some casts in property-entry-test
Documentation: kunit: Clean up some string casts in examples
...
Partially revert "thunderbolt: test: Remove some casts which are no
longer required". It turns out that typeof() doesn't support bitfields,
so these still need to be cast to the appropriate enum.
The only mention of typeof() and bitfields I can find is in the proposal
to standardise them:
http://www.open-std.org/jtc1/sc22/wg14/www/docs/n2619.htm
This was caught by the kernel test robot:
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org/thread/FDKBHAV7QNLNFU5NBI2RKV56DWDSOLGM/
Fixes: 8f0877c26e ("thunderbolt: test: Remove some casts which are no longer required")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
With some of the stricter type checking in KUnit's EXPECT macros
removed, several casts in the thunderbolt KUnit tests are no longer
required.
Remove the unnecessary casts, making the conditions clearer.
Signed-off-by: David Gow <davidgow@google.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
DROM for USB4 host/device has a shorter header than Thunderbolt DROM
header. This patch addresses host/device with USB4 DROM (According to spec:
Universal Serial Bus 4 (USB4) Device ROM Specification, Rev 1.0, Feb-2021).
While there correct the data_len field to be 12 bits and rename
__unknown1 to reserved following the spec.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Alder Lake has the same integrated Thunderbolt/USB4 controller as
Intel Tiger Lake. By default it is still using firmware based connection
manager so we can use most of the Tiger Lake flows.
Add the Alder Lake PCI IDs to the driver list of supported devices.
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This include is not needed so drop it.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In Intel Tiger Lake and beyond it takes some time after the force power
is set until the firmware connection manager is ready. So instead of
reading it once we poll it for 10ms before giving up.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We only need to set up the device links when software connection manager
path is used. The firmware connection manager does not need them and if
they are present they may even cause problems.
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We should not dereference ->dual_link_port if it is NULL and lane bonding
is requested. For this reason move lane bonding configuration happen
inside the block where ->dual_link_port != NULL.
Fixes: 54509f5005 ("thunderbolt: Add KUnit tests for path walking")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the NVM authentication fails immediately, like if the firmware
detects that the image is not valid for some reason, better to read the
status once and if set to non-zero fail the operation accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same way we support these two operations for USB4 routers we can
extend the retimer NVM operations to support retimers also.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It may be useful if the actual NVM authentication can be delayed to be
run later, for instance when the user logs out. For this reason add a
new NVM operation (AUHENTICATE_ONLY) that just triggers the authentication
procedure over whatever was written to the NVM storage.
This is not supported with Thunderbolt 1-3 devices, though.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently these write ops are used for updating router firmware images
only. Moving to tb.h helps the retimers also to use the same ops.
Also add tb_ prefix to the enum while there.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With help from platform firmware (ACPI) it is possible to power on
retimers even when there is no USB4 link (e.g nothing is connected to
the USB4 ports). This allows us to bring the USB4 sideband up so that we
can access retimers and upgrade their NVM firmware.
If the platform has support for this, we expose two additional
attributes under USB4 ports: offline and rescan. These can be used to
bring the port offline, rescan for the retimers and put the port online
again. The retimer NVM upgrade itself works the same way than with cable
connected.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When accessing retimers when there is no cable connected we are going to
need additional USB4 port operations. First the port needs to be put
into offline mode, and then the sideband channel transactions must be
enabled on the SBTX line. This adds support for these operations.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Typically retimers can be accessed only when the USB4 link is up (e.g
there is a cable connected). However, sometimes it is useful to be able
to access retimers even if there is nothing connected to the USB4 port.
For instance we may still want to be able to upgrade the retimer NVM
firmware even if the user does not have any USB4 devices. This is
something that USB4 spec leaves to implementers.
In case of ACPI based systems, we can support this by providing a
special _DSM method under each USB4 port. This _DSM can be used to turn
on power to on-board retimers (and cycle it through different modes so
that the sideband becomes usable).
This patch adds support for this _DSM and makes the functionality
available to the rest of the driver through tb_acpi_power_[on|off]_retimers().
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create devices for each USB4 port. This is needed when we add retimer
access when there is no device connected but may be useful for other
purposes too following what USB subsystem does. This exports a single
attribute "link" that shows the type of the USB4 link (or "none" if
there is no cable connected).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The upstream port can be connected to any previous generation
Thunderbolt port so logging as "TBT" is more accurate than "TBT3.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Goshen Ridge reports wrong DP main credits in NVM 27 and earlier,
so add a quirk that fixes it. We also need to expand the quirk table to
match on hardware vendor/device IDs too.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 Connection Manager guide provides detailed information how the
USB4 router buffer (credit) allocation information should be used by the
connection manager when it allocates buffers for different paths. This
patch implements it for Linux. For USB 3.x and DisplayPort we use
directly the router preferences. The rest of the buffer space is then
used for PCIe and DMA (peer-to-peer, XDomain) traffic. DMA tunnels
require at least one buffer and PCIe six, so if there is not enough
buffers we fail the tunnel creation.
For the legacy Thunderbolt 1-3 devices we use the existing hard-coded
scheme except for DMA where we use the values suggested by the USB4 spec
chapter 13.
Co-developed-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Once lane bonding has been enabled (or disabled) both lane adapters may
update their total credits accordingly. For this reason re-read the port
credits after lane bonding has been enabled or disabled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 routers must expose their preferred credit (buffer) allocation
information through router operation. This information tells the
connection manager how the router prefers its buffers to be allocated to
get the expected bandwidth for the supported protocols.
Read this information and store it as part of struct tb_switch for each
USB4 router.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It may take some time until the two lanes enter bonded state so poll for
the link width to match what is expected before going forward. This ensures
the link is in expected state before we start establishing paths through
it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
With the USB4 buffer allocation the number of credits (and non-flow
credits) may be different depending on the router buffer allocation
preferences. To allow this move the nfc_credits field to struct
tb_path_hop.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The function does not modify the object in any way so make the parameter
const to reflect this.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 Configuration Manager guide suggests that the USB4 port wakes
are configured in a certain way, like that when the port is configured
the wake-on-connect should not be set and so forth, so align the driver
with this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Latest USB4 spec added a new wake bit for DisplayPort so add this to the
driver when runtime suspending. This way wake up the domain when a new
monitor is plugged in to any of the device routers.
Also do the same for pre-USB4 devices through the link controller
registers as documented in chapter 13 of the USB4 spec.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that we have generic functionality available in nvm.c make the DMA
port code call it instead of duplicating the functionality.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We do this for Thunderbolt 2/3 devices through DMA port, USB4 devices
and retimers pretty much the same way. Only the actual block read/write
is different. For this reason split out the NVM read/write functions
from usb4.c to nvm.c and make USB4 device code call these when needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add new device known to support self-authenticate on disconnect.
Signed-off-by: Crag Wang <crag.wang@dell.com>
Reviewed-by: Mario Limonciello <mario.limonciello@outlook.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Up to 64 bytes of data can be read from NVM in one go.
Read address must be dword aligned. Data is read into a local buffer.
If caller asks to read data starting at an unaligned address then full
dword is anyway read from NVM into a local buffer. Data is then copied
from the local buffer starting at the unaligned offset to the caller
buffer.
In cases where asked data length + unaligned offset is over 64 bytes
we need to make sure we don't read past the 64 bytes in the local
buffer when copying to caller buffer, and make sure that we don't
skip copying unaligned offset bytes from local buffer anymore after
the first round of 64 byte NVM data read.
Fixes: b04079837b ("thunderbolt: Add initial support for USB4")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Up to 64 bytes of data can be read from NVM in one go. Read address
must be dword aligned. Data is read into a local buffer.
If caller asks to read data starting at an unaligned address then full
dword is anyway read from NVM into a local buffer. Data is then copied
from the local buffer starting at the unaligned offset to the caller
buffer.
In cases where asked data length + unaligned offset is over 64 bytes
we need to make sure we don't read past the 64 bytes in the local
buffer when copying to caller buffer, and make sure that we don't
skip copying unaligned offset bytes from local buffer anymore after
the first round of 64 byte NVM data read.
Fixes: 3e13676862 ("thunderbolt: Add support for DMA configuration based mailbox")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This includes following Thunderbolt/USB4 changes for v5.13 merge window:
* Debugfs improvements
* Align the inter-domain (peer-to-peer) support with the USB4
inter-domain spec for better interoperability
* Add support for USB4 DROM and the new product descriptor
* More KUnit tests
* Detailed uevent for routers
* Few miscellaneous improvements
All these have been in linux-next without reported issues.
-----BEGIN PGP SIGNATURE-----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=RzJl
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.13 merge window
This includes following Thunderbolt/USB4 changes for v5.13 merge window:
* Debugfs improvements
* Align the inter-domain (peer-to-peer) support with the USB4
inter-domain spec for better interoperability
* Add support for USB4 DROM and the new product descriptor
* More KUnit tests
* Detailed uevent for routers
* Few miscellaneous improvements
All these have been in linux-next without reported issues.
* tag 'thunderbolt-for-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (24 commits)
thunderbolt: Hide authorized attribute if router does not support PCIe tunnels
thunderbolt: Add details to router uevent
thunderbolt: Unlock on error path in tb_domain_add()
thunderbolt: Add support for USB4 DROM
thunderbolt: Check quirks in tb_switch_add()
thunderbolt: Add KUnit tests for DMA tunnels
thunderbolt: Add KUnit tests for XDomain properties
net: thunderbolt: Align the driver to the USB4 networking spec
thunderbolt: Allow multiple DMA tunnels over a single XDomain connection
thunderbolt: Drop unused tb_port_set_initial_credits()
thunderbolt: Use dedicated flow control for DMA tunnels
thunderbolt: Add support for maxhopid XDomain property
thunderbolt: Add tb_property_copy_dir()
thunderbolt: Align XDomain protocol timeouts with the spec
thunderbolt: Use pseudo-random number as initial property block generation
thunderbolt: Do not re-establish XDomain DMA paths automatically
thunderbolt: Add more logging to XDomain connections
Documentation / thunderbolt: Drop speed/lanes entries for XDomain
thunderbolt: Decrease control channel timeout for software connection manager
thunderbolt: Do not pass timeout for tb_cfg_reset()
...
With USB4 devices PCIe tunneling is optional so for device routers
without PCIe upstream adapter it does not make much sense to expose the
authorized attribute. For this reason hide it if PCIe tunneling is not
supported by the device router.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expose two environment variables for routers as part of the initial
uevent:
USB4_VERSION=1.0
USB4_TYPE=host|device|hub
Userspace can use this information to expose more details about each
connected device. Only USB4 devices have USB4_VERSION but all devices
have USB4_TYPE.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This array uses 1-based indexing so it corrupts memory one element
beyond of the array. Fix it by making the array one element larger.
Fixes: dacb12877d ("thunderbolt: Add support for on-board retimers")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
After the device_register() succeeds, then the correct way to clean up
is to call device_unregister(). The unregister calls both device_del()
and device_put(). Since this code was only device_del() it results in
a memory leak.
Fixes: dacb12877d ("thunderbolt: Add support for on-board retimers")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We accidentally deleted this unlock on the error path. Undelete it.
Fixes: 7f0a34d790 ("thunderbolt: Decrease control channel timeout for software connection manager")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 router DROM differs sligthly from Thunderbolt 1-3 DROM. For
instance it does not include UID and CRC8 in the header section, and it
has product descriptor genereric entry to describe the product IDs and
related information. If the "Version" field in the DROM header section
reads 3 it means the router only has USB4 DROM and if it reads 1 it
means the router supports TBT3 compatible DROM.
For this reason, update the DROM parsing code to support "pure" USB4
DROMs too.
While there drop the extra empty line at the end of tb_drom_read().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently we have had an artificial limitation of a single DMA tunnel
per XDomain connection. However, hardware wise there is no such limit
and software based connection manager can take advantage of all the DMA
rings available on the host to establish tunnels.
For this reason make the tb_xdomain_[enable|disable]_paths() to take the
DMA ring and HopID as parameter instead of storing them in the struct
tb_xdomain. We also add API functions to allocate input and output
HopIDs of the XDomain connection that the service drivers can use
instead of hard-coding.
Also convert the two existing service drivers over to this API.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 inter-domain service spec recommends using dedicated flow
control scheme so update the driver accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 inter-domain spec mandates that the compatible hosts expose a new
property "maxhopid" that tells the connection manager on the other side
what is the maximum supported input HopID over the connection. Since
this is depend on the lane adapter the cable is connected it needs to be
filled in dynamically.
For this reason we take a copy of the global properties and fill then
for each XDomain connection upon first connect, and then keep updating
it if the generation changes as services are being added/removed. We
also take advantage of this copy to fill in the hostname.
We also expose this maxhopid as an attribute under each XDomain device.
While there drop kernel-doc entry for property_lock which seems to be
left there when the structure was originally introduced.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This function takes a deep copy of the properties. We need this in order
to support more dynamic properties per XDomain connection as required by
the USB4 inter-domain service spec.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 inter-domain service spec has slightly different recommended
timeouts for the XDomain protocol so align the driver with those.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
As recommended by USB4 inter-domain service spec use pseudo-random value
instead of zero as initial XDomain property block generation value.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This step is actually not needed. The service drivers themselves will
handle this once they have negotiated the service up and running again
with the remote side. Also dropping this makes it easier to add support
for multiple DMA tunnels over a single XDomain connection.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently the driver is pretty quiet when another host is connected
which makes debugging possible issues harder. For this reason add more
logging on debug level that can be turned on as needed.
While there log the host-to-host connection on info level analogous to
routers and retimers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When the firmware connection manager is not proxying between the
software and the hardware we can decrease the timeout for control
packets significantly. The USB4 spec recommends 10 ms +- 1 ms but we use
slightly larger value (100 ms) which is recommendation from Intel
Thunderbolt firmware folks. When firmware connection manager is running
then we keep using the existing 5000 ms.
To implement this we move the control channel allocation to
tb_domain_alloc(), and pass the timeout from that function to the
tb_ctl_alloc(). Then make both connection manager implementations pass
the timeout when they alloc the domain structure.
While there update kernel-doc of struct tb_ctl to match the reality.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is only one user for this function and it passes the default
timeout to it anyway, so remove the parameter completely. This is also
needed in the subsequent patch where we allow connection manager
implementations to use different timeout for non-raw control channel
messages.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In most cases the response packet is lost because the router in question
was disconnected by the user. Resending the control packet in that case
just adds unnecessary delays, so disable that for intra-domain control
packets. For inter-domain (XDomain) packets we continue retrying.
This also aligns the driver better what the Intel connection manager
firmware is doing.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently, when first failure occurs while reading of the block,
we stop reading the block and jump to the next capability.
This doesn't cover the case of block with "holes" of inaccessible
dwords, followed by accessible dwords.
This patch address this problem.
In case of failure while reading the complete block in one transaction,
(because of one or more dwords is inaccessible), we read the remaining
dwords of the block dword-by-dword, one dword per transaction,
till the end of the block.
By doing this, we handle the case of block with "holes" of inaccessible
dwords, followed by accessible dwords. The accessible dwords are shown
with the fields: <offset> <relative_offset> <cap_id> <vs_cap_id> <value>
E.g.:
0x01eb 236 0x05 0x06 0x0000d166
While the inaccesible dwords are shown as: <offset> <not accessible>
E.g.:
0x01ed <not accessible>
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the driver is unbound and then bound back it goes over the topology
and figure out the existing tunnels. However, if it finds DP tunnel it
should make sure the domain does not runtime suspend as otherwise it
will tear down the DP tunnel unexpectedly.
Fixes: 6ac6faee5d ("thunderbolt: Add runtime PM for Software CM")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If there is a failure before the tb_switch_add() is called the switch
object is released by tb_switch_release() but at that point HopID IDAs
have not yet been initialized. So we see splat like this:
BUG: spinlock bad magic on CPU#2, kworker/u8:5/115
...
Workqueue: thunderbolt0 tb_handle_hotplug
Call Trace:
dump_stack+0x97/0xdc
? spin_bug+0x9a/0xa7
do_raw_spin_lock+0x68/0x98
_raw_spin_lock_irqsave+0x3f/0x5d
ida_destroy+0x4f/0x127
tb_switch_release+0x6d/0xfd
device_release+0x2c/0x7d
kobject_put+0x9b/0xbc
tb_handle_hotplug+0x278/0x452
process_one_work+0x1db/0x396
worker_thread+0x216/0x375
kthread+0x14d/0x155
? pr_cont_work+0x58/0x58
? kthread_blkcg+0x2e/0x2e
ret_from_fork+0x1f/0x40
Fix this by always initializing HopID IDAs in tb_switch_alloc().
Fixes: 0b2863ac3c ("thunderbolt: Add functions for allocating and releasing HopIDs")
Cc: stable@vger.kernel.org
Reported-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Drop the two functions not used anymore in the driver.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There are cases when reading block of dwords in single transaction fail,
for several reasons, mostly if HW publish to implement all of the dwords,
while actually it doesn't or if some dwords not accessible for read
for security reasons. We handle these cases by trying to read the block,
dword-by-dword, one dword per transaction, till we get a failure.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This includes following Thunderbolt/USB4 changes for v5.12 merge
window:
* Start lane initialization after sleep for Thunderbolt 3 compatible
devices
* Add support for de-authorizing PCIe tunnels (software based
connection manager only)
* Add support for new ACPI 6.4 USB4 _OSC
* Allow disabling XDomain protocol
* Add support for new SL5 security level
* Clean up kernel-docs to pass W=1 builds
* A couple of cleanups and minor fixes
All these have been in linux-next without reported issues.
-----BEGIN PGP SIGNATURE-----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=pzr4
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.12 merge window
This includes following Thunderbolt/USB4 changes for v5.12 merge
window:
* Start lane initialization after sleep for Thunderbolt 3 compatible
devices
* Add support for de-authorizing PCIe tunnels (software based
connection manager only)
* Add support for new ACPI 6.4 USB4 _OSC
* Allow disabling XDomain protocol
* Add support for new SL5 security level
* Clean up kernel-docs to pass W=1 builds
* A couple of cleanups and minor fixes
All these have been in linux-next without reported issues.
* tag 'thunderbolt-for-v5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (27 commits)
thunderbolt: Add support for native USB4 _OSC
ACPI: Add support for native USB4 control _OSC
ACPI: Execute platform _OSC also with query bit clear
thunderbolt: Allow disabling XDomain protocol
thunderbolt: Add support for PCIe tunneling disabled (SL5)
thunderbolt: dma_test: Drop unnecessary include
thunderbolt: Add clarifying comments about USB4 terms router and adapter
thunderbolt: switch: Fix kernel-doc descriptions of non-static functions
thunderbolt: nhi: Fix kernel-doc descriptions of non-static functions
thunderbolt: path: Fix kernel-doc descriptions of non-static functions
thunderbolt: eeprom: Fix kernel-doc descriptions of non-static functions
thunderbolt: ctl: Fix kernel-doc descriptions of non-static functions
thunderbolt: switch: Fix function name in the header
thunderbolt: tunnel: Fix misspelling of 'receive_path'
thunderbolt: icm: Fix a couple of formatting issues
thunderbolt: switch: Demote a bunch of non-conformant kernel-doc headers
thunderbolt: tb: Kernel-doc function headers should document their parameters
thunderbolt: nhi: Demote some non-conformant kernel-doc headers
thunderbolt: xdomain: Fix 'tb_unregister_service_driver()'s 'drv' param
thunderbolt: eeprom: Demote non-conformant kernel-doc headers to standard comment blocks
...
ACPI 6.4 introduced a new _OSC capability used to negotiate whether the
OS is supposed to use Software (native) or Firmware based Connection
Manager. If the native support is granted then there are set of bits
that enable/disable different tunnel types that the Software Connection
Manager is allowed to tunnel.
This adds support for this new USB4 _OSC accordingly. When PCIe
tunneling is disabled then the driver switches security level to be
"nopcie" following the security level 5 used in Firmware based
Connection Manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
This allows disabling XDomain protocol completely if the user does not
plan to use the USB4/Thunderbolt peer-to-peer functionality, or for
security reasons.
XDomain protocol is enabled by default but with this commit it is
possible to disable it by passing "xdomain=0" as module parameter (or
through the kernel command line).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Recent Intel Thunderbolt firmware connection manager has support for
another security level, SL5, that disables PCIe tunneling. This option
can be turned on from the BIOS.
When this is set the driver exposes a new security level "nopcie" to the
userspace and hides the authorized attribute under connected devices.
While there we also hide it when "dponly" security level is enabled
since it is not really usable in that case anyway.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
USB4 spec talks about routers and adapters whereas Thunderbolt 1-3
talked about CIO (Converged I/O) switches and ports. These are the same
thing but might cause confusion so add clarifying comments to struct
tb_switch and struct tb_port about the USB4 terms.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fix kernel-doc descriptions of all non-static functions. This also gets
rid of the warnings on W=1 build.
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Fix kernel-doc descriptions of the two non-static functions. This also
gets rids of the warnings on W=1 build.
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Fix kernel-doc descriptions of the two non-static functions. This also
gets rid of the warnings on W=1 build.
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Fix kernel-doc descriptions of the two non-static functions. This also
gets rid of the rest of the warnings on W=1 build.
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Fix kernel-doc descriptions of all non-static functions and struct
tb_cfg. Gets rid of several warnings on W=1 builds too.
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lee Jones <lee.jones@linaro.org>
When we walk up the device hierarchy in tb_acpi_add_link() make sure we
break the loop if the device has no parent. Otherwise we may crash the
kernel by dereferencing a NULL pointer.
Fixes: b2be2b05cf ("thunderbolt: Create device links from ACPI description")
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/thunderbolt/switch.c:1322: warning: expecting prototype for reset_switch(). Prototype was for tb_switch_reset() instead
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/thunderbolt/tunnel.c:841: warning: Function parameter or member 'receive_path' not described in 'tb_tunnel_alloc_dma'
drivers/thunderbolt/tunnel.c:841: warning: Excess function parameter 'reveive_path' description in 'tb_tunnel_alloc_dma'
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/thunderbolt/icm.c:122: warning: Function parameter or member 'xdomain_connected' not described in 'icm'
drivers/thunderbolt/icm.c:122: warning: Function parameter or member 'xdomain_disconnected' not described in 'icm'
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/thunderbolt/switch.c:730: warning: Function parameter or member 'port' not described in 'tb_init_port'
drivers/thunderbolt/switch.c:1348: warning: Function parameter or member 'sw' not described in 'tb_plug_events_active'
drivers/thunderbolt/switch.c:1348: warning: Function parameter or member 'active' not described in 'tb_plug_events_active'
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[ mw: Demote only static functions ]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/thunderbolt/tb.c:535: warning: Function parameter or member 'sw' not described in 'tb_scan_switch'
drivers/thunderbolt/tb.c:551: warning: Function parameter or member 'port' not described in 'tb_scan_port'
drivers/thunderbolt/tb.c:711: warning: Function parameter or member 'tb' not described in 'tb_free_invalid_tunnels'
drivers/thunderbolt/tb.c:726: warning: Function parameter or member 'sw' not described in 'tb_free_unplugged_children'
drivers/thunderbolt/tb.c:1129: warning: Function parameter or member 'work' not described in 'tb_handle_hotplug'
drivers/thunderbolt/tb.c:1239: warning: Function parameter or member 'tb' not described in 'tb_handle_event'
drivers/thunderbolt/tb.c:1239: warning: Function parameter or member 'type' not described in 'tb_handle_event'
drivers/thunderbolt/tb.c:1239: warning: Function parameter or member 'buf' not described in 'tb_handle_event'
drivers/thunderbolt/tb.c:1239: warning: Function parameter or member 'size' not described in 'tb_handle_event'
drivers/thunderbolt/tb.c:1239: warning: expecting prototype for tb_schedule_hotplug_handler(). Prototype was for tb_handle_event() instead
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/thunderbolt/nhi.c:53: warning: Function parameter or member 'ring' not described in 'ring_interrupt_active'
drivers/thunderbolt/nhi.c:53: warning: Function parameter or member 'active' not described in 'ring_interrupt_active'
drivers/thunderbolt/nhi.c:114: warning: Function parameter or member 'nhi' not described in 'nhi_disable_interrupts'
drivers/thunderbolt/nhi.c:191: warning: Function parameter or member 'ring' not described in 'ring_write_descriptors'
drivers/thunderbolt/nhi.c:225: warning: Function parameter or member 'work' not described in 'ring_work'
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[ mw: Demote only static functions ]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/thunderbolt/xdomain.c:678: warning: Function parameter or member 'drv' not described in 'tb_unregister_service_driver'
drivers/thunderbolt/xdomain.c:678: warning: Excess function parameter 'xdrv' description in 'tb_unregister_service_driver'
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jesper Dangaard Brouer <hawk@kernel.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: bpf@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/thunderbolt/eeprom.c:19: warning: Function parameter or member 'sw' not described in 'tb_eeprom_ctl_write'
drivers/thunderbolt/eeprom.c:19: warning: Function parameter or member 'ctl' not described in 'tb_eeprom_ctl_write'
drivers/thunderbolt/eeprom.c:27: warning: Function parameter or member 'sw' not described in 'tb_eeprom_ctl_read'
drivers/thunderbolt/eeprom.c:27: warning: Function parameter or member 'ctl' not described in 'tb_eeprom_ctl_read'
drivers/thunderbolt/eeprom.c:27: warning: expecting prototype for tb_eeprom_ctl_write(). Prototype was for tb_eeprom_ctl_read() instead
drivers/thunderbolt/eeprom.c:43: warning: Function parameter or member 'sw' not described in 'tb_eeprom_active'
drivers/thunderbolt/eeprom.c:43: warning: Function parameter or member 'enable' not described in 'tb_eeprom_active'
drivers/thunderbolt/eeprom.c:73: warning: Function parameter or member 'sw' not described in 'tb_eeprom_transfer'
drivers/thunderbolt/eeprom.c:73: warning: Function parameter or member 'ctl' not described in 'tb_eeprom_transfer'
drivers/thunderbolt/eeprom.c:73: warning: Function parameter or member 'direction' not described in 'tb_eeprom_transfer'
drivers/thunderbolt/eeprom.c:97: warning: Function parameter or member 'sw' not described in 'tb_eeprom_out'
drivers/thunderbolt/eeprom.c:97: warning: Function parameter or member 'val' not described in 'tb_eeprom_out'
drivers/thunderbolt/eeprom.c:117: warning: Function parameter or member 'sw' not described in 'tb_eeprom_in'
drivers/thunderbolt/eeprom.c:117: warning: Function parameter or member 'val' not described in 'tb_eeprom_in'
drivers/thunderbolt/eeprom.c:138: warning: Function parameter or member 'sw' not described in 'tb_eeprom_get_drom_offset'
drivers/thunderbolt/eeprom.c:138: warning: Function parameter or member 'offset' not described in 'tb_eeprom_get_drom_offset'
drivers/thunderbolt/eeprom.c:170: warning: Function parameter or member 'sw' not described in 'tb_eeprom_read_n'
drivers/thunderbolt/eeprom.c:170: warning: Function parameter or member 'offset' not described in 'tb_eeprom_read_n'
drivers/thunderbolt/eeprom.c:170: warning: Function parameter or member 'val' not described in 'tb_eeprom_read_n'
drivers/thunderbolt/eeprom.c:170: warning: Function parameter or member 'count' not described in 'tb_eeprom_read_n'
drivers/thunderbolt/eeprom.c:383: warning: Function parameter or member 'sw' not described in 'tb_drom_parse_entries'
drivers/thunderbolt/eeprom.c:417: warning: Function parameter or member 'sw' not described in 'tb_drom_copy_efi'
drivers/thunderbolt/eeprom.c:417: warning: Function parameter or member 'size' not described in 'tb_drom_copy_efi'
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[ mw: Demote only static functions ]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/thunderbolt/ctl.c:38: warning: expecting prototype for struct tb_cfg. Prototype was for struct tb_ctl instead
drivers/thunderbolt/ctl.c:350: warning: Function parameter or member 'ctl' not described in 'tb_ctl_tx'
drivers/thunderbolt/ctl.c:350: warning: Function parameter or member 'data' not described in 'tb_ctl_tx'
drivers/thunderbolt/ctl.c:350: warning: Function parameter or member 'len' not described in 'tb_ctl_tx'
drivers/thunderbolt/ctl.c:350: warning: Function parameter or member 'type' not described in 'tb_ctl_tx'
drivers/thunderbolt/ctl.c:350: warning: expecting prototype for tb_cfg_tx(). Prototype was for tb_ctl_tx() instead
drivers/thunderbolt/ctl.c:383: warning: Function parameter or member 'ctl' not described in 'tb_ctl_handle_event'
drivers/thunderbolt/ctl.c:383: warning: Function parameter or member 'type' not described in 'tb_ctl_handle_event'
drivers/thunderbolt/ctl.c:383: warning: Function parameter or member 'pkg' not described in 'tb_ctl_handle_event'
drivers/thunderbolt/ctl.c:383: warning: Function parameter or member 'size' not described in 'tb_ctl_handle_event'
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[ mw: Demote only static functions ]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/thunderbolt/cap.c:189: warning: Function parameter or member 'sw' not described in 'tb_switch_find_cap'
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
... and take the error path if it fails.
Fixes the following W=1 kernel build warning(s):
drivers/thunderbolt/dma_port.c: In function ‘dma_port_flash_write_block’:
drivers/thunderbolt/dma_port.c:331:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In some cases it is useful to be able de-authorize devices. For example
if user logs out the userspace can have a policy that disconnects PCIe
devices until logged in again. This is only possible for software based
connection manager as it directly controls the tunnels.
For this reason make the authorized attribute accept writing 0 which
makes the software connection manager to tear down the corresponding
PCIe tunnel. Userspace can check if this is supported by reading a new
domain attribute deauthorization, that holds 1 in that case.
While there correct tb_domain_approve_switch() kernel-doc and
description of authorized attribute to mention that it is only about
PCIe tunnels.
Cc: Christian Kellner <christian@kellner.me>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
USB4 spec says that for TBT3 compatible device routers the connection
manager needs to set SLI (Start Lane Initialization) to get the lanes
that were not connected back to functional state after sleep. Same needs
to be done if the link was XDomain.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
The only usage of these is to put their addresses in arrays of pointers
to const attribute_groups. Make them const to allow the compiler to put
them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The tb_dbg() call is using %#x that already adds the 0x prefix so don't
duplicate it.
Fixes: 9039387e16 ("thunderbolt: Add USB4 router operation proxy for firmware connection manager")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
This includes following Thunderbolt/USB4 changes for v5.11 merge window:
* DMA traffic test driver
* USB4 router NVM upgrade improvements
* USB4 router operations proxy implementation available in the recent
Intel Connection Manager firmwares
* Support for Intel Maple Ridge discrete Thunderbolt 4 controller
* A couple of cleanups and minor improvements.
-----BEGIN PGP SIGNATURE-----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=+RXF
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.11 merge window
This includes following Thunderbolt/USB4 changes for v5.11 merge window:
* DMA traffic test driver
* USB4 router NVM upgrade improvements
* USB4 router operations proxy implementation available in the recent
Intel Connection Manager firmwares
* Support for Intel Maple Ridge discrete Thunderbolt 4 controller
* A couple of cleanups and minor improvements.
* tag 'thunderbolt-for-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (22 commits)
thunderbolt: Add support for Intel Maple Ridge
thunderbolt: Add USB4 router operation proxy for firmware connection manager
thunderbolt: Move constants for USB4 router operations to tb_regs.h
thunderbolt: Add connection manager specific hooks for USB4 router operations
thunderbolt: Pass TX and RX data directly to usb4_switch_op()
thunderbolt: Pass metadata directly to usb4_switch_op()
thunderbolt: Perform USB4 router NVM upgrade in two phases
thunderbolt: Return -ENOTCONN when ERR_CONN is received
thunderbolt: Keep the parent runtime resumed for a while on device disconnect
thunderbolt: Log adapter numbers in decimal in path activation/deactivation
thunderbolt: Log which connection manager implementation is used
thunderbolt: Move max_boot_acl field to correct place in struct icm
MAINTAINERS: Add Isaac as maintainer of Thunderbolt DMA traffic test driver
thunderbolt: Add DMA traffic test driver
thunderbolt: Add support for end-to-end flow control
thunderbolt: Make it possible to allocate one directional DMA tunnel
thunderbolt: Create debugfs directory automatically for services
thunderbolt: Add functions for enabling and disabling lane bonding on XDomain
thunderbolt: Add link_speed and link_width to XDomain
thunderbolt: Create XDomain devices for loops back to the host
...
Maple Ridge is first discrete USB4 host controller from Intel. It comes
with firmware based connection manager and the flows are similar as used
in Intel Titan Ridge.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Maple Ridge and Tiger Lake connection manager firmware implements
a USB4 router operation proxy that should be used instead of direct
register access to avoid races with the firmware. This is supported in
all firmwares where the protocol version field returned in the driver
ready response is 3 (or higher).
This adds the USB4 router proxy operations support to the driver so that
we first check the protocol version and if it is 3 (or higher) the USB4
router operation is run through the firmware provided proxy. Otherwise
the native version is used.
Most USB4 router proxy operations are pretty straightforward except
NVM_AUTH where the firmware only responds once the router is restarted
but before it sends device connected notification. To support this we
split the operation so that the reply is received asynchronously and
stored to struct icm. This last reply is then returned in
icm_usb4_switch_nvm_authenticate_status() if available.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We are going to use these in subsequent patch so make them available
outside of usb4.c.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel USB4 host routers that run the firmware based connection manager
(ICM) may implement a proxy for USB4 router operations. This is to avoid
the firmware to race with the OS driver, as both may need to run these
operations.
This adds two new connection manager specific callbacks which, if
provided, get called instead of the native USB4 router operation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We are going to make usb4_switch_op() to match better the corresponding
firmware (ICM) USB4 router operation proxy interface, so that we can use
either based on the connection manager implementation.
For this reason rename usb4_switch_op() to __usb4_switch_op() that
provides the most complete interface. Then make usb4_switch_op() and
usb4_switch_op_data() call it with correct set of parameters and update
the callers accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We are going to make usb4_switch_op() to match better the corresponding
firmware (ICM) USB4 router operation proxy interface, so that we can use
either based on the connection manager implementation. For this reason
pass metadata directly to usb4_switch_op().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The currect code expects that the router returns back the status of the
NVM authentication immediately. When tested against a real USB4 device
what happens is that the router is reset and only after that the result
is updated in the ROUTER_CS_26 register status field. This also seems to
align better what the spec suggests.
For this reason do the same what we already do with the Thunderbolt 3
devices and perform the NVM upgrade in two phases. First start the
NVM_AUTH router operation and once the router is added back after the
reset read the status in ROUTER_CS_26 and expose it to the userspace
accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This allows the calling code to distinguish if the error was due to
ERR_CONN (adapter is disconneced or disabled) or something else. Will be
needed in USB4 router NVM update in the following patch.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When doing device firmware upgrade the device will disconnect for a
while and then reconnect back. Keep the parent device (and the whole
domain) powered for a while so we don't need to runtime resume
immediately when the device is connected back after the device upgrade
completes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This makes it consistent with other debug logs that already are using
decimal number for adapters (ports).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This makes it easier to figure out whether the driver is using firmware
or software based connection manager implementation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This makes the kernel-doc to match the ordering and also this is better
place for it, not between upstream_port and vnd_cap that are used
together.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Paulian reported a crash that happens when a dock is unplugged during
hibernation:
[78436.228217] thunderbolt 0-1: device disconnected
[78436.228365] BUG: kernel NULL pointer dereference, address: 00000000000001e0
...
[78436.228397] RIP: 0010:icm_free_unplugged_children+0x109/0x1a0
...
[78436.228432] Call Trace:
[78436.228439] icm_rescan_work+0x24/0x30
[78436.228444] process_one_work+0x1a3/0x3a0
[78436.228449] worker_thread+0x30/0x370
[78436.228454] ? process_one_work+0x3a0/0x3a0
[78436.228457] kthread+0x13d/0x160
[78436.228461] ? kthread_park+0x90/0x90
[78436.228465] ret_from_fork+0x1f/0x30
This happens because remove_unplugged_switch() calls tb_switch_remove()
that releases the memory pointed by sw so the following lines reference
to a memory that might be released already.
Fix this by saving pointer to the parent device before calling
tb_switch_remove().
Reported-by: Paulian Bogdan Marinca <paulian@marinca.net>
Fixes: 4f7c2e0d87 ("thunderbolt: Make sure device runtime resume completes before taking domain lock")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver allows sending DMA traffic over XDomain connection.
Specifically over a loopback connection using either a Thunderbolt/USB4
cable that is connected back to the host router port, or a special
loopback dongle that has RX and TX lines crossed. This can be useful at
manufacturing floor to check whether Thunderbolt/USB4 ports are
functional.
The driver exposes debugfs directory under the XDomain service that can
be used to configure the driver, start the test and check the results.
If a loopback dongle is used the steps to send and receive 1000 packets
can be done like:
# modprobe thunderbolt_dma_test
# echo 1000 > /sys/kernel/debug/thunderbolt/<service_id>/dma_test/packets_to_receive
# echo 1000 > /sys/kernel/debug/thunderbolt/<service_id>/dma_test/packets_to_send
# echo 1 > /sys/kernel/debug/thunderbolt/<service_id>/dma_test/test
# cat /sys/kernel/debug/thunderbolt/<service_id>/dma_test/status
When a cable is connected back to host then there are two Thunderbolt
services, one is configured for receiving (does not matter which one):
# modprobe thunderbolt_dma_test
# echo 1000 > /sys/kernel/debug/thunderbolt/<service_a>/dma_test/packets_to_receive
# echo 1 > /sys/kernel/debug/thunderbolt/<service_a>/dma_test/test
The other one for sending:
# echo 1000 > /sys/kernel/debug/thunderbolt/<service_b>/dma_test/packets_to_send
# echo 1 > /sys/kernel/debug/thunderbolt/<service_b>/dma_test/test
Results can be read from both services status attributes.
Signed-off-by: Isaac Hazan <isaac.hazan@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 spec defines end-to-end (E2E) flow control that can be used between
hosts to prevent overflow of a RX ring. We previously had this partially
implemented but that code was removed with commit 53f13319d1
("thunderbolt: Get rid of E2E workaround") with the idea that we add it
back properly if there ever is need. Now that we are going to add DMA
traffic test driver (in subsequent patches) this can be useful.
For this reason we modify tb_ring_alloc_rx/tx() so that they accept
RING_FLAG_E2E and configure the hardware ring accordingly. The RX side
also requires passing TX HopID (e2e_tx_hop) used in the credit grant
packets.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With DMA tunnels it is possible that the service using it does not
require bi-directional paths so make RX and TX optional (but of course
one of them needs to be set).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows service drivers to use it as parent directory if they need
to add their own debugfs entries.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These can be used by service drivers to enable and disable lane bonding
as needed.
Signed-off-by: Isaac Hazan <isaac.hazan@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link speed and link width are needed for checking expected values in
case of using a loopback service.
Signed-off-by: Isaac Hazan <isaac.hazan@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is perfectly possible to have loops back from the routers to the
host, or even from one host port to another. Instead of ignoring these,
we create XDomain devices for each. This allows creating services such
as DMA traffic test that is used in manufacturing for example.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are going to represent loops back to the host also as XDomains and
they all have the same (host) UUID, so finding them needs to use route
string instead. This also requires that we check if the XDomain device
is added to the bus before its properties can be updated. Otherwise the
remote UUID might not be populated yet.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These fields are marked as vendor defined in the USB4 spec and should
not be modified by the software, so only clear them when we are dealing
with pre-USB4 hardware.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Tiger Lake-H has the same Thunderbolt/USB4 controller as Tiger
Lake-LP. Add the Tiger Lake-H PCI IDs to the driver list of supported
devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Only USB4 lane 0 adapter has the USB4 port capability for wakes so only
program wakes on such adapters.
Fixes: b2911a593a ("thunderbolt: Enable wakes from system suspend")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Some calls in the debugfs interface are made to the linux/uaccess.h header,
but the header is not referenced. So, for x86_64 architectures, this
dependency seems to be pulled in elsewhere, which leads to a successful
compilation. However, on arm/arm64 architectures, it was found to error out
on implicit declarations.
This change fixes the implicit declaration error by adding the
linux/uaccess.h header.
Fixes: 54e418106c ("thunderbolt: Add debugfs interface")
Signed-off-by: Casey Bowman <casey.g.bowman@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The svc->key field is not released as it should be if ida_simple_get()
fails so fix that.
Fixes: 9aabb68568 ("thunderbolt: Fix to check return value of ida_simple_get")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
ring_request_msix() misses to call ida_simple_remove() in an error path.
Add a label 'err_ida_remove' and jump to it.
Fixes: 046bee1f9a ("thunderbolt: Add MSI-X support")
Cc: stable@vger.kernel.org
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This includes following Thunderbolt/USB4 changes for v5.10 merge window:
* A couple of optimizations around Tiger Lake force power logic and
NHI (Native Host Interface) LC (Link Controller) mailbox command
processing
* Power management improvements for Software Connection Manager
* Debugfs support
* Allow KUnit tests to be enabled also when Thunderbolt driver is
configured as module.
* Few minor cleanups and fixes
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=KvWM
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.10 merge window
This includes following Thunderbolt/USB4 changes for v5.10 merge window:
* A couple of optimizations around Tiger Lake force power logic and
NHI (Native Host Interface) LC (Link Controller) mailbox command
processing
* Power management improvements for Software Connection Manager
* Debugfs support
* Allow KUnit tests to be enabled also when Thunderbolt driver is
configured as module.
* Few minor cleanups and fixes
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (37 commits)
thunderbolt: Capitalize comment on top of QUIRK_FORCE_POWER_LINK_CONTROLLER
thunderbolt: Correct tb_check_quirks() kernel-doc
thunderbolt: Log correct zeroX entries in decode_error()
thunderbolt: Handle ERR_LOCK notification
thunderbolt: Use "if USB4" instead of "depends on" in Kconfig
thunderbolt: Allow KUnit tests to be built also when CONFIG_USB4=m
thunderbolt: Only stop control channel when entering freeze
thunderbolt: debugfs: Fix uninitialized return in counters_write()
thunderbolt: Add debugfs interface
thunderbolt: No need to warn in TB_CFG_ERROR_INVALID_CONFIG_SPACE
thunderbolt: Introduce tb_switch_is_tiger_lake()
thunderbolt: Introduce tb_switch_is_ice_lake()
thunderbolt: Check for Intel vendor ID when identifying controller
thunderbolt: Introduce tb_port_is_nhi()
thunderbolt: Introduce tb_switch_next_cap()
thunderbolt: Introduce tb_port_next_cap()
thunderbolt: Move struct tb_cap_any to tb_regs.h
thunderbolt: Add runtime PM for Software CM
thunderbolt: Create device links from ACPI description
ACPI: Export acpi_get_first_physical_node() to modules
...
There was copy & paste error so it always printed value of pkg->zero1.
Also use tb_ctl_warn() here, no need to print backtrace.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the USB4 router downstream port is locked, sending configuration
packet to a router below it causes ERR_LOCK to be sent. Instead of warn
splat about unknown error we log the error (just warning level) and
return -EACCESS instead. The idea is that we may want to do something
when such error code is received, like perform unlock.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This groups the USB4 options more nicely, and also does not require that
every config option lists explicit depends on USB4.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This adds a bit more build coverage for the tests even though these are
not expected to be enabled by normal users and distros. In order to make
this working we need to open-code kunit_test_suite() and call the
relevant functions directly in the driver init/exit hook.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
According to the kernel power management documentation freeze phase
should only quiesce the device, no need to configure wakes or put it to
low power state. For this reason we simply stop the control channel and
in case of Software Connection Manager also mark the hotplug disabled.
This should align the driver better with the PM framework expectations.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
One more fix that makes ASUS PA27AC Thunderbolt 3 monitor work more
reliably.
This has been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=sgTO
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
thunderbolt: Fix for v5.9-rc6
One more fix that makes ASUS PA27AC Thunderbolt 3 monitor work more
reliably.
This has been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Retry DROM read once if parsing fails
If the first line is in an invalid format then the "ret" value is
uninitialized. We should return -EINVAL instead.
Fixes: 54e418106c ("thunderbolt: Add debugfs interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Kai-Heng reported that sometimes DROM parsing of ASUS PA27AC Thunderbolt 3
monitor fails. This makes the driver to fail to add the device so only
DisplayPort tunneling is functional.
It is not clear what exactly happens but waiting for 100 ms and retrying
the read seems to work this around so we do that here.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206493
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This adds debugfs interface that can be used for debugging possible
issues in hardware/software. It exposes router and adapter config spaces
through files like this:
/sys/kernel/debug/thunderbolt/<DEVICE>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/path
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/counters
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/path
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/counters
...
The "regs" is either the router or port configuration space register
dump. The "path" is the port path configuration space and "counters" is
the optional counters configuration space.
These files contains one register per line so it should be easy to use
normal filtering tools to find the registers of interest if needed.
The router and adapter regs file becomes writable when
CONFIG_USB4_DEBUGFS_WRITE is enabled (which is not supposed to be done
in production systems) and in this case the developer can write "offset
value" lines there to modify the hardware directly. For convenience this
also supports the long format the read side produces (but ignores the
additional fields). The counters file can be written even when
CONFIG_USB4_DEBUGFS_WRITE is not enabled and it is only used to clear
the counter values.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This may be returned for example when accessing some of the vendor
specific capabilities. It is not fatal by any means so instead of WARN()
just log it as debug level. The caller gets error back anyway and is
expected to handle it accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to differentiate Tiger Lake from other controllers.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to differentiate Ice Lake from other controllers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With USB4 there will be other vendors so make sure the current checks
for different Intel controllers will not accidentally match those.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is useful if one needs to check if adapter (port) is the host
interface (NHI). Make tb_port_alloc_hopid() take advantage of this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is similar to tb_port_next_cap() but instead allows walking
capability list of a switch (router). Convert tb_switch_find_cap() and
tb_switch_find_vse_cap() to use this as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is useful for walking port config space (adapter)
capability lists. Convert the tb_port_find_cap() to use this as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure will be needed by the debugfs implementation so make it
available outside of cap.c.
While there add kernel-doc comments to the structure.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds runtime PM support for the Software Connection Manager parts
of the driver. This allows to save power when either there is no device
attached at all or there is a device attached and all following
conditions are true:
- Tunneled PCIe root/downstream ports are runtime suspended
- Tunneled USB3 ports are runtime suspended
- No active DisplayPort stream
- No active XDomain connection
For the first two we take advantage of device links that were added in
previous patch. Difference for the system sleep case is that we also
enable wakes when something is geting plugged in/out of the Thunderbolt
ports.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The new way to describe relationship between tunneled ports and USB4 NHI
(Native Host Interface) is with ACPI _DSD looking like below for a PCIe
downstream port:
Scope (\_SB.PCI0)
{
Device (NHI0) { } // Thunderbolt NHI
Device (DSB0) // Hotplug downstream port
{
Name (_DSD, Package () {
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {"usb4-host-interface", \_SB.PCI0.NHI0},
...
}
})
}
}
This is "documented" in these [1] USB-IF slides and being used on
systems that ship with Windows.
The _DSD can be added to tunneled USB3 and PCIe ports, and is needed to
make sure the USB4 NHI is resumed before any of the tunneled ports so
the protocol tunnels get established properly before the actual port
itself is resumed. Othwerwise the USB/PCI core find the link may not be
established and starts tearing down the device stack.
This parses the ACPI description each time NHI is probed and tries to
find devices that has the property and it references the NHI in
question. For each matching device a device link from that device to the
NHI is created.
Since USB3 ports themselves do not get runtime suspended with the parent
device (hub) we do not add the link from the USB3 port to USB4 NHI but
instead we add the link from the xHCI device. This makes the device link
usable for runtime PM as well.
[1] https://www.usb.org/sites/default/files/D1T2-2%20-%20USB4%20on%20Windows.pdf
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On older Apple systems there is currently a PCI quirk in place to block
resume of tunneled PCIe ports until NHI (Thunderbolt controller) is
resumed. This makes sure the PCIe tunnels are re-established before PCI
core notices it.
With device links the same thing can be done without quirks. The driver
core will make sure the supplier (NHI) is resumed before consumers (PCIe
downstream ports).
For this reason switch the Thunderbolt driver to use device links and
remove the PCI quirk.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
In order for the router and the whole domain to wake up from system
suspend states we need to enable wakes for the connected routers. For
device routers we enable wakes from PCIe and USB 3.x. This allows
devices such as keyboards connected to USB 3.x hub that is tunneled to
wake the system up as expected. For all routers we enabled wake on USB4
for each connected ports. This is used to propagate the wake from router
to another.
Do the same for legacy routers through link controller vendor specific
registers as documented in USB4 spec chapter 13.
While there correct kernel-doc of usb4_switch_set_sleep() -- it does not
enable wakes instead there is a separate function (usb4_switch_set_wake())
that does.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec mandates that the lane 1 should be disabled if lanes are not
bonded. For host-to-host connections (XDomain) we don't support lane
bonding so in order to be compatible with the spec, disable lane 1 when
another host is connected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When the port is connected to another host it should be marked as such
in the USB4 port capability. This information is used by the router
during sleep and wakeup.
Also do the same for legacy switches via link controller vendor specific
registers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Both ends of the link needs to have this set. Otherwise the link is not
re-established properly after sleep. Now since it is possible to have
mixed USB4 and Thunderbolt 1, 2 and 3 devices we need to split the link
configuration functionality to happen per port so we can pick the
correct implementation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
During testing it was noticed that the link is not properly restored
after the domain exits sleep if the link configured bits are set before
lane bonding is enabled. The USB4 spec does not say in which order these
need to be set but setting link configured afterwards makes the link
restoration work so we do that instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Some early stage USB4 devices do not like that any of the enumerating
router config space fields (ROUTER_CS_1 - ROUTER_CS_4) are written after
the initial enumeration for example when entering sleep states. The
default timeout by the USB4 spec is 10 ms which should be fine for the
driver to handle.
For this reason do not change the notification timeout from the default
10 ms for USB4 routers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The TMU will be reset after router exits sleep so in order to
re-configure it upon resume make sure the structure is initialized again
based on the current hardware state.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
DP tunnels do not need the same kind of treatment as others because they
are created based on hot-plug events on DP adapter ports, and the
display stack does not need the tunnels to be enabled when resuming from
suspend. Also Tiger Lake Thunderbolt controller sends unplug event on D3
exit so this avoids that as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
First generation routers may need the reset command upon resume but it
is not supported by newer generations.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec says that NFC buffers field is not used for protocol adapters,
only for lane adapters so make tb_port_add_nfc_credits() skip non-lane
adapters in order to follow the spec.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In Tiger Lake the Firmware CM is always enabled (so bit 0 is always set)
but it may be in "pass through" mode which means it requires Software CM
instead. This can be determined by checking bit 31 instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When Software CM is running it should not send any NHI mailbox command
during PM flows. Only force power bit needs to be set and cleared so
change Tiger Lake (well and Ice Lake) nhi_ops to take this into account.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently the Ice Lake and Tiger Lake NHI (host controller) LC (link
controller) mailbox command processing checks for the completion of
command every 100 msecs. These controllers are found to complete this in
the order of 1 ms or so. Since this delay is in suspend path, surplus
delay is effectively affecting runtime PM suspend flows.
Optimize this so that we do the wait for 1 ms after reading the mailbox
register. This should make Ice Lake and Tiger Lake runtime suspend take
less time to complete.
Reported-by: Dana Alkattan <dana.alkattan@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently the "Force Power" logic uses 10 retries, each with a delay of
250 ms. Thunderbolt controllers in Ice Lake and Tiger Lake platforms are
found to complete this in the order of 3 ms or so. Since this delay
is in resume path, surplus delay is effectively affecting runtime PM
resume flows.
Decrease the granularity of the delay to 3 ms and increase the number of
retries so we wait maximum of ~1 s which is the recommended timeout.
This should make runtime resume a bit faster.
Reported-by: Dana Alkattan <dana.alkattan@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Doesn't really matter for an individual driver, but it may
get coppied to lots more. I consider it's a little tidy up.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This includes two fixes, one that fixes a regression around reboot and
other that uses a correct link rate when USB3 bandwidth is reclaimed
when the link is not up.
Both have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=vxwa
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
thunderbolt: Fixes for v5.9-rc4
This includes two fixes, one that fixes a regression around reboot and
other that uses a correct link rate when USB3 bandwidth is reclaimed
when the link is not up.
Both have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Use maximum USB3 link rate when reclaiming if link is not up
thunderbolt: Disable ports that are not implemented
If the USB3 link is not up the actual link rate is 0 so when reclaiming
bandwidth we should look at maximum supported link rate instead.
Cc: stable@vger.kernel.org
Fixes: 0bd680cd90 ("thunderbolt: Add USB3 bandwidth management")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit 4caf2511ec ("thunderbolt: Add trivial .shutdown") exposes a bug
in the Thunderbolt driver, that frees an unallocated id, resulting in the
following spinlock bad magic bug.
[ 20.633803] BUG: spinlock bad magic on CPU#4, halt/3313
[ 20.640030] lock: 0xffff92e6ad5c97e0, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[ 20.672139] Call Trace:
[ 20.675032] dump_stack+0x97/0xdb
[ 20.678950] ? spin_bug+0xa5/0xb0
[ 20.682865] do_raw_spin_lock+0x68/0x98
[ 20.687397] _raw_spin_lock_irqsave+0x3f/0x5d
[ 20.692535] ida_destroy+0x4f/0x124
[ 20.696657] tb_switch_release+0x6d/0xfd
[ 20.701295] device_release+0x2c/0x7d
[ 20.705622] kobject_put+0x8e/0xac
[ 20.709637] tb_stop+0x55/0x66
[ 20.713243] tb_domain_remove+0x36/0x62
[ 20.717774] nhi_remove+0x4d/0x58
Fix the issue by disabling ports that are enabled as per the EEPROM, but
not implemented. While at it, update the kernel doc for the disabled
field, to reflect this.
Cc: stable@vger.kernel.org
Fixes: 4caf2511ec ("thunderbolt: Add trivial .shutdown")
Reported-by: Srikanth Nandamuri <srikanth.nandamuri@intel.com>
Signed-off-by: Nikunj A. Dadhania <nikunj.dadhania@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Some external devices can support completing thunderbolt authentication
when they are unplugged. For this to work though, the link controller must
remain operational.
The only device known to support this right now is the Dell WD19TB, so add
a quirk for this.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This allows userspace to have a shorter period of time that the device
is unusable and to call it at a more convenient time.
For example flushing the image may happen while the user is using the
machine and authenticating/rebooting may happen while logging out.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The 32 bit int value 512 is being left shifted and then used in a context
that expects the expression to be a larger unsigned long. There may be
a potential integer overflow, so make 512 a UL before shift to avoid
any such issues.
Addresses-Coverity: ("Uninintentional integer overflow")
Fixes: 3b1d8d577c ("thunderbolt: Implement USB3 bandwidth negotiation routines")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec specifies standard access to retimers (both on-board and
cable) through USB4 port sideband access. This makes it possible to
upgrade their firmware in the same way than we already do with the
routers.
This enumerates on-board retimers under each USB4 port when the link
comes up and adds them to the bus under the router the retimer belongs
to. Retimers are exposed in sysfs with name like <device>:<port>.<index>
where device is the router the retimer belongs to, port is the USB4 port
the retimer is connected to and index is the retimer index under that
port (starting from 1). This applies to the upstream USB4 port as well
so if there is on-board retimer between the port and the router it is
also added accordingly.
At this time we do not add cable retimers but there is no techincal
restriction to do so in the future if needed. It is not clear whether it
makes sense to upgrade their firmwares and at least Thunderbolt 3 cables
it has not been done outside of lab environments.
The sysfs interface is made to follow the router NVM upgrade to make it
easy to extend the existing userspace (fwupd) to handle these as well.
Signed-off-by: Kranthi Kuntala <kranthi.kuntala@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec specifies standard set of sideband operations that are send
over the low speed link to access either retimers on the link or the
link parter (the other router). The USB4 retimer spec extends these and
adds operations for retimer NVM upgrade.
This implements the retimer access and NVM upgrade USB4 port sideband
operations which we need for retimer support in the patch that follows.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Especially when accessing retimers over USB4 sideband operations the
possibility to get read errors seems to be higher so make the
usb4_do_read_data() retry a couple of times if it sees any other error
than -ENODEV (device is gone). We can only do this for read side because
it carries the offset as part of metadata (as opposed to writes).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently these functions operate on struct tb_switch but we are going
to need the same functionality with retimers as well so make the two
functions work with an arbitrary object that gets passed as parameter to
the callbacks.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We are going to reuse some of this functionality to implement retimer
NVM upgrade so move common NVM functionality into its own file. We also
rename the structure from tb_switch_nvm to tb_nvm to make it clear that
it is not just for switches.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
With USB4 Intel is also using its USB-IF ID (0x8087) with the new
devices. The NVM format is the same. Add this to the driver so NVM
upgrade is possible with these devices as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We can test some parts of tunneling, like path allocation without access
to test hardware so add KUnit tests for PCIe, DP and USB3 tunneling.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB3 supports both isochronous and non-isochronous traffic. The former
requires guaranteed bandwidth and can take up to 90% of the total
bandwidth. With USB4 USB3 is tunneled over USB4 fabric which means that
we need to make sure there is enough bandwidth allocated for the USB3
tunnels in addition to DisplayPort tunnels.
Whereas DisplayPort bandwidth management is static and done before the
DP tunnel is established, the USB3 bandwidth management is dynamic and
allows increasing and decreasing the allocated bandwidth according to
what is currently consumed. This is done through host router USB3
downstream adapter registers.
This adds USB3 bandwidth management to the software connection manager
so that we always try to allocate maximum bandwidth for DP tunnels and
what is left is allocated for USB3.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We need to call this from tb.c when we improve the bandwidth management
to take USB3 into account.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Each host router USB3 downstream adapter has a set of registers that are
used to negotiate bandwidth between the connection manager and the
internal xHCI controller. These registers allow dynamic bandwidth
management for USB3 isochronous traffic based on what is actually
consumed vs. allocated at any given time.
Implement these USB3 bandwidth negotiation routines to allow the
software connection manager take advantage of these.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Sometimes it takes longer for DPRX to be set so increase the timeout to
cope with this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Whereas DisplayPort bandwidth is consumed only in one direction (from DP
IN adapter to DP OUT adapter), USB3 adds separate bandwidth for both
upstream and downstream directions.
For this reason extend the tunnel consumed bandwidth routines to support
both directions and implement this for DP.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Just for symmetry with the usb4_switch_map_usb3_down() make this one
also return ports that are enabled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We need to call this on enabled ports in order to find the mapping from
host router USB4 port to a USB 3.x downstream adapter, so make the
function return enabled ports as well.
While there fix parameter alignment in tb_find_usb3_down().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB3 tunneling is possible only over USB4 link so don't create USB3
tunnels if that's not the case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec allows DP tunneling from any router that has DP IN adapter,
not just from host router. The driver currently only added the DP IN
resources for the host router because Thunderbolt 1, 2 and 3 devices do
not have DP IN adapters. However, USB4 allows device routers to have DP
IN adapter as well so update the driver to add DP IN resources for each
device that has one. One example would be an eGPU enclosure where the
eGPU output is forwarded to DP IN port and then tunneled over the USB4
fabric.
Only limitation we add now is that the DP IN and DP OUT that gets paired
for tunnel creation should both be under the same topology starting from
host router downstream port. In other words we do not create DP tunnels
across host router at this time even though that is possible as well but
it complicates the bandwidth management and there is no real use-case
for this anyway.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This adds KUnit tests for path walking which is only dependent on
software structures, so no hardware is needed to run these.
We make these available only when both KUnit and the driver itself are
built into the kernel image. The reason for this is that KUnit adds its
own module_init() call in kunit_test_suite() which generates linker
error because the driver does the same in nhi.c. This should be fine for
now because these tests are only meant to run by developers anyway.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently we have only supported paths that follow daisy-chain topology
but USB4 also allows to build trees of devices. For this reason increase
maximum path length we use for discovery to be from the lowest level to
the host router and back to the same level.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the path is not complete when we do discovery the number of hops may
be less than with the full path. As an example when this can happen is
that user unloads the driver, disconnects the topology, and loads the
driver back. If there is PCIe or USB3 tunnel involved this may happen.
Take this into account in tb_pcie_init_path() and tb_usb3_init_path()
and prevent potential access over array limits.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add sanity check that given src and dst ports are reachable through path
walk before allocating a path. If they are not then bail out early.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
With USB4, topologies are not limited to daisy-chains anymore so when
calculating how many hops are between two ports we need to walk the
whole path instead.
Add helper function tb_for_each_port_on_path() that can be used to walk
over each port on a path and make tb_path_alloc() to use it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 makes it possible to have tree topology of devices connected in the
same way than USB3. This was actually possible in Thunderbolt 1, 2 and 3
as well but all the available devices only had two ports which allows
building only daisy-chains of devices.
With USB4 it is possible for example that there is DP IN adapter as part
of eGPU device router and that should be tunneled over the tree topology
to a DP OUT adapter. This updates the tb_next_port_on_path() to support
such topologies.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB3 discovery used wrong indices when tunnel is discovered. It
should use TB_USB3_PATH_DOWN for path that flows downstream and
TB_USB3_PATH_UP when it flows upstream. This should not affect the
functionality but better to fix it.
Fixes: e6f8185857 ("thunderbolt: Add support for USB 3.x tunnels")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org # v5.6+
The end-to-end (E2E) workaround is needed for Falcon Ridge (TBT 2)
controller when E2E is enabled for both ends of the host-to-host
connection. However, we never supported full E2E in the first place so
this code is not necessary at the moment. Further this allows us to use
all available rings for data except ring 0 which is reserved for the
control path.
The complete E2E flow control is explained in the USB4 spec so we may
add it back later if needed but at least the networking driver seems to
work fine without, and the higher level stack, like TCP will retransmit
lost packets anyway.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
NHI (The host interface adapter) is allowed to use HopIDs 1-7 as well so
relax the restriction in tb_port_alloc_hopid() to support this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
While Intel hardware typically has hop_count (Total Paths in the spec)
12 the USB4 spec allows this to be anything between 1 and 21 so no need
to warn about this. Simply log number of paths at debug level.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
On a systems where the Thunderbolt controller is present all the time
the kernel nodename may not yet set by the userspace when the driver is
loaded. This means when another host is connected it may see the default
"(none)" hostname instead of the system real hostname.
For this reason build the initial XDomain property block only upon first
connect. This should make sure the userspace has had chance to set it up.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fix the spelling of "specification", and add a missing "the" article.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzqVA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynftwCfeanyI6TR5AdfJVZN50B6/ySvVwcAn07i9VRX
tnt2kz0UqReYpLt0wyJ7
=YP7o
-----END PGP SIGNATURE-----
Merge tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY driver updates from Greg KH:
"Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (245 commits)
usb: dwc3: meson-g12a: fix USB2 PHY initialization on G12A and A1 SoCs
usb: dwc3: meson-g12a: fix error path when fetching the reset line fails
Revert "dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings"
Revert "dt-bindings: usb: qcom,dwc3: Add compatible for SC7180"
Revert "dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver"
USB: serial: ch341: fix lockup of devices with limited prescaler
USB: serial: ch341: add basis for quirk detection
CDC-ACM: heed quirk also in error handling
USB: serial: option: add Telit LE910C1-EUX compositions
usb: musb: Fix runtime PM imbalance on error
usb: musb: jz4740: Prevent lockup when CONFIG_SMP is set
usb: musb: mediatek: add reset FADDR to zero in reset interrupt handle
usb: musb: use true for 'use_dma'
usb: musb: start session in resume for host port
usb: musb: return -ESHUTDOWN in urb when three-strikes error happened
USB: serial: qcserial: add DW5816e QDL support
thunderbolt: Add trivial .shutdown
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
...
This adds support for Intel Tiger Lake Thunderbolt controller using
firmware based connection manager. In addition the driver can now be
built on non-x86 architectures as well. Then there are a couple of
commits that make the driver work across kexec, replace a zero length
array with flexible one, and revert one change that is not needed
anymore because of NVMem subsystem improvements.
-----BEGIN PGP SIGNATURE-----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=qZRi
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.8 merge window
This adds support for Intel Tiger Lake Thunderbolt controller using
firmware based connection manager. In addition the driver can now be
built on non-x86 architectures as well. Then there are a couple of
commits that make the driver work across kexec, replace a zero length
array with flexible one, and revert one change that is not needed
anymore because of NVMem subsystem improvements.
* tag 'thunderbolt-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Add trivial .shutdown
thunderbolt: Update Kconfig to allow building on other architectures.
thunderbolt: Replace zero-length array with flexible-array
thunderbolt: Add support for Intel Tiger Lake
Revert "thunderbolt: Prevent crash if non-active NVMem file is read"
On my machine, a kexec with this driver loaded in the old kernel causes
a very long delay on boot in the kexec'ed kernel, most likely due to
unclean shutdown prior to that.
Unloading thunderbolt driver prior to kexec allows kexec to work as fast
as regular kernel boot, as well as adding this .shutdown pointer.
Shutting a device prior to the shutdown completely is always a good idea
IMHO to help with kexec, and this one-liner patch implements it.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Previously we used pcie_find_root_port() to find a Root Port from a PCIe
device and pci_find_pcie_root_port() to find a Root Port from a
Conventional PCI device.
Unify the two functions and use pcie_find_root_port() to find a Root Port
from either a Conventional PCI device or a PCIe device. Then there is no
need to distinguish the type of the device.
Link: https://lore.kernel.org/r/1589019568-5216-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # thunderbolt
Thunderbolt 3 and USB4 shouldn't be x86 only.
Tested on a SolidRun HoneyComb (ARM Cortex-A72) with a
Gigabyte Titan Ridge Thunderbolt 3 PCIe card (JHL7540).
Signed-off-by: David Manouchehri <david.manouchehri@riseup.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The function misses checking return value of tb_sw_read() before it
accesses the value that was read. Fix this by checking the return value
first.
Fixes: b04079837b ("thunderbolt: Add initial support for USB4")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tiger Lake integrated Thunderbolt/USB4 controller is quite close to
Intel Ice Lake. By default it is still using firmware based connection
manager so we can use most of the Ice Lake flows in Tiger Lake as well.
We check if the firmware connection manager is running and in that case
use it, otherwise use the software based connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
This reverts commit 03cd45d2e2.
Commit 664f054938 ("nvmem: core: use is_bin_visible for permissions")
incidentally adds support for write-only nvmem. Hence, this workaround
is no longer required, so drop it.
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
- A couple of commits that make the driver to use flexible-array member
instead of zero-length array extension. This allows compiler to issue a
warning if the flexible array is not the last member of a structure.
- Use scnprintf() instead of snprintf() to avoid potential buffer
overflow.
-----BEGIN PGP SIGNATURE-----
iQJUBAABCgA+FiEEVTdhRGBbNzLrSUBaAP2fSd+ZWKAFAl5wdFcgHG1pa2Eud2Vz
dGVyYmVyZ0BsaW51eC5pbnRlbC5jb20ACgkQAP2fSd+ZWKBfbg/8CKZxEIh7Qms5
CBuHU689e0sEwN/vRiAgBspiKJTDUk5lZRl0wDFun1+2DV3AGrExJj07k//xG9Zw
on9ma1TKufkZsuy2yllAb70fE8SdhZ3ZUIqrFvCGj2g5NwRWZvFE0L47zM5Wi+wt
y5k1ifJUrgVCliZjgKDg7EXXP7InLBFtT89yL9LaQ71to+tp2PI5EDN/1JGOnDUV
3c/WPqw0bPmQbW/E8CT9vU+Jd3Jh6bEHKJqXTZwj6bLGWP0aiegPzk2/04m7rG3A
kq7hrwubOEVSsZogRRuZEbiNKX5jMwCPUGvd6qC2kZnKJxanEu/syOSt+yBhE2NW
f2D7WBdCAtxCh8AiMAJDcLphvpY/LrXk2+i710kaSH/Xfl4D5z6QTbsQ0jTx9FIs
O08rYuikd0lxd/Zr2+qEbCna2UEjTarxEInyKKYm04H8HFycm3OtAN6pzm+O11W7
LFJebmTFounwvOknRx+30k1X3ylperMZhhDRXg6J2gh1y2Dxy2EgnFY/mX0IivwD
7PHIgvD34I2RpgIrUYNa/R9TDuKDGsA2FnEYL9XBU+f7VWwam0U+Zw088NpMUMsB
8b/hFhgyeds1FRwCdrepM+UT5xwsykIycUZaV/g6KwXaNCYjygTFGPCHI4+cjLBe
MNA31gcVUu62ya4vgUUL2Kz5vt3TrLw=
=/p8i
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.7 merge window
- A couple of commits that make the driver to use flexible-array member
instead of zero-length array extension. This allows compiler to issue a
warning if the flexible array is not the last member of a structure.
- Use scnprintf() instead of snprintf() to avoid potential buffer
overflow.
* tag 'thunderbolt-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Use scnprintf() for avoiding potential buffer overflow
thunderbolt: icm: Replace zero-length array with flexible-array member
thunderbolt: eeprom: Replace zero-length array with flexible-array member
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This function is type bool, and it's supposed to return true on success.
Unfortunately, this path takes negative error codes and casts them to
bool (true) so it's treated as success instead of failure.
Fixes: 91c0c12080 ("thunderbolt: Add support for lane bonding")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The driver does not populate .reg_read callback for the non-active NVMem
because the file is supposed to be write-only. However, it turns out
NVMem subsystem does not yet support this and expects that the .reg_read
callback is provided. If user reads the binary attribute it triggers
NULL pointer dereference like this one:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
Call Trace:
bin_attr_nvmem_read+0x64/0x80
kernfs_fop_read+0xa7/0x180
vfs_read+0xbd/0x170
ksys_read+0x5a/0xd0
do_syscall_64+0x43/0x150
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix this in the driver by providing .reg_read callback that always
returns an error.
Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Fixes: e6b245ccd5 ("thunderbolt: Add support for host and device NVM firmware upgrade")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200213095604.1074-1-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case where the call tb_switch_exceeds_max_depth is true
the error reurn path leaks memory in sw. Fix this by setting
the return error code to -EADDRNOTAVAIL and returning via the
error exit path err_free_sw_ports to free sw. sw has been kzalloc'd
so the free of the NULL sw->ports is fine.
Addresses-Coverity: ("Resource leak")
Fixes: b04079837b ("thunderbolt: Add initial support for USB4")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191220220526.11307-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code tried to check whether xhci variable has ROUTER_CS_6_HCI bit
set but since xhci type is bool and it already holds true or false based
on that very bit, fix the check to use the variable directly.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: b04079837b ("thunderbolt: Add initial support for USB4")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20200108125317.36444-2-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 added a capability to tunnel USB 3.x protocol over the USB4
fabric. USB4 device routers may include integrated SuperSpeed HUB or a
function or both. USB tunneling follows PCIe so that the tunnel is
created between the parent and the child router from USB3 downstream
adapter port to USB3 upstream adapter port over a single USB4 link.
This adds support for USB 3.x tunneling and also capability to discover
existing USB 3.x tunnels (for example created by connection manager in
boot firmware).
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-9-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Time Management Unit (TMU) is included in each USB4 router. It is used
to synchronize time across the USB4 fabric. By default when USB4 router
is plugged to the domain, its TMU is turned off. This differs from
Thunderbolt (1, 2 and 3) devices whose TMU is by default configured to
bi-directional HiFi mode. Since time synchronization is needed for
proper Display Port tunneling this means we need to configure the TMU on
USB4 compliant devices.
The USB4 spec allows some flexibility on how the TMU can be configured.
This makes it possible to enable link power management states (CLx) in
certain topologies, where for example DP tunneling is not used. TMU can
also be re-configured dynamicaly depending on types of tunnels created
over the USB4 fabric.
In this patch we simply configure the TMU to be in bi-directional HiFi
mode. This way we can tunnel any kind of traffic without need to perform
complex steps to re-configure the domain dynamically. We can add more
fine-grained TMU configuration later on when we start enabling CLx
states.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-8-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to find switch capabilities in order to implement TMU support so
make it available to other files as well.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-7-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the driver now supports USB4 which is the standard going forward,
update the Kconfig entry to mention this and rename the entry from
CONFIG_THUNDERBOLT to CONFIG_USB4 instead to help people to find the
correct option if they want to enable USB4.
Also do the same for Thunderbolt network driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/r/20191217123345.31850-6-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 is the public specification based on Thunderbolt 3 protocol. There
are some differences in register layouts and flows. In addition to PCIe
and DP tunneling, USB4 supports tunneling of USB 3.x. USB4 is also
backward compatible with Thunderbolt 3 (and older generations but the
spec only talks about 3rd generation). USB4 compliant devices can be
identified by checking USB4 version field in router configuration space.
This patch adds initial support for USB4 compliant hosts and devices
which enables following features provided by the existing functionality
in the driver:
- PCIe tunneling
- Display Port tunneling
- Host and device NVM firmware upgrade
- P2P networking
This brings the USB4 support to the same level that we already have for
Thunderbolt 1, 2 and 3 devices.
Note the spec talks about host and device "routers" but in the driver we
still use term "switch" in most places. Both can be used interchangeably.
Co-developed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-5-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 1.0 section 6.4.2.7 specifies a new field (PG) in notification
packet that is sent as response of hot plug/unplug events. This field
tells whether the acknowledgment is for plug or unplug event. This needs
to be set accordingly in order the router to send further hot plug
notifications.
To make it simpler we fill the field unconditionally. Legacy devices do
not look at this field so there should be no problems with them.
While there rename tb_cfg_error() to tb_cfg_ack_plug() and update the
log message accordingly. The function is only used to ack plug/unplug
events.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-4-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are going to re-use tb_drom_read() for USB4 DROM reading as well.
USB4 has separate router operations for this which does not need the
drom_offset. Therefore we move call to tb_eeprom_get_drom_offset() into
tb_eeprom_read_n() where it is needed.
While there change return -ENOSYS to -ENODEV because the former is only
supposed to be used with system calls (invalid syscall nr).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-3-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will be needing this when adding initial USB4 support so make it
available to other files in the driver as well. We also rename it to
tb_switch_find_port() to follow conventions used in switch.c.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-2-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On zang's Dell XPS 13 9370 after Thunderbolt NVM firmware upgrade the
Thunderbolt controller did not come back as expected. Only after the
system was rebooted it became available again. It is not entirely clear
what happened but I suspect the new NVM firmware image authentication
failed for some reason. Regardless of this the router needs to be power
cycled if NVM authentication fails in order to get it fully functional
again.
This modifies the driver to issue a power cycle in case the NVM
authentication fails immediately when dma_port_flash_update_auth()
returns. We also need to call tb_switch_set_uuid() earlier to be able to
fetch possible NVM authentication failure when DMA port is added.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205457
Reported-by: zang <dump@tzib.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since now we can do pretty much the same thing in the software
connection manager than the firmware would do, there is no point
starting it by default. Instead we can just continue using the software
connection manager.
Make it possible for user to switch between the two by adding a module
pararameter (start_icm) which is by default false. Having this ability
to enable the firmware may be useful at least when debugging possible
issues with the software connection manager implementation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Titan Ridge supports Display Port 1.4 which adds HBR3 (High Bit Rate)
rates that may be up to 8.1 Gb/s over 4 lanes. This translates to
effective data bandwidth of 25.92 Gb/s (as 8/10 encoding is removed by
the DP adapters when going over Thunderbolt fabric). If another high
rate monitor is connected we may need to reduce the bandwidth it
consumes so that it fits into the total 40 Gb/s available on the
Thunderbolt fabric.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
To perform proper Display Port tunneling for Thunderbolt 3 devices we
need to allocate DP resources for DP IN port before they can be used.
The reason for this is that the user can also connect a monitor directly
to the Type-C ports in which case the Thunderbolt controller acts as
re-driver for Display Port (no tunneling takes place) taking the DP
sinks away from the connection manager. This allocation is done using
special sink allocation registers available through the link controller.
We can pair DP IN to DP OUT only if
* DP IN has sink allocated via link controller
* DP OUT port receives hotplug event
For DP IN adapters (only for the host router) we first query whether
there is DP resource available (it may be the previous instance of the
driver for example already allocated it) and if it is we add it to the
list. We then update the list when after each plug/unplug event to a DP
IN/OUT adapter. Each time the list is updated we try to find additional
DP IN <-> DP OUT pairs for tunnel establishment. This strategy also
makes it possible to establish another tunnel in case there are 3
monitors connected and one gets unplugged releasing the DP IN adapter
for the new tunnel.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Titan Ridge needs an additional connection manager handshake in order to
do proper Display Port tunneling so implement it here.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to keep PCIe hierarchies consistent across hotplugs, add
hard-coded PCIe downstream port to Thunderbolt port for Alpine Ridge and
Titan Ridge as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For a casual reader tb_switch_is_cr() does not tell much so instead
spell out the full controller name in the function name. For example
tb_switch_is_cr() becomes tb_switch_is_cactus_ridge() which is easier
to understand.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We currently read how sibling lane adapter ports relate each other from
DROM (Device ROM). If the two lane adapter ports go through the same
physical connector these lanes can then be bonded together. However,
some cases DROM does not provide this information or it is missing
completely (host routers typically do not have DROM). In this case we
have hard-coded the relationship.
Expand this to work with both legacy devices where lane adapter ports 1
and 2, and 3 and 4 are always linked together, and with USB4 devices
where lane adapter 1 is always following lane adapter 0 or is disabled
completely (see USB4 section 5.2.1 for more information).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Lane bonding allows aggregating two 10/20 Gb/s (depending on the
generation) lanes into a single 20/40 Gb/s bonded link. This allows
sharing the full bandwidth more efficiently. In order to establish lane
bonding we need to check that lane bonding is possible through link
controller and that both ends of the link actually supports 2x widths.
This also means that all the paths should be established through the
primary port so update tb_path_alloc() to handle this as well.
Lane bonding is supported starting from Falcon Ridge (2nd generation)
controllers.
We also expose the current speed and number of lanes under each device
except the host router following similar attribute naming than USB bus.
Expose speed and number of lanes for both directions to allow possibility
of asymmetric link in the future.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently add_switch() takes a huge amount of parameters that makes it
hard to maintain. Instead of passing all those parameters we can split
the function into two parts (alloc and add) and fill the additional
switch fields directly in the functions calling those.
While there remove redundant error logging in case kmemdup() fails.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There are quite many places in the driver where we iterate over each
port in the switch. To make it bit more convenient, add a macro that can
be used to iterate over each port and convert existing call sites to use it.
This is based on code by Lukas Wunner.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that USB4 spec has names for these DP adapter registers we can use
them instead. This makes it easier to match certain register to the spec.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that USB4 spec has names for these PCIe adapter registers we can use
them instead. This makes it easier to match certain register to the spec.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that USB4 spec has names for these basic registers we can use them
instead. This makes it easier to match certain register to the spec.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If we fail to add a switch for some reason log an error instead of
keeping silent. This is useful for debugging.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We currently differentiate between SW CM (Software Connection Manager,
sometimes also called External Connection Manager) and ICM (Firmware
based Connection Manager, Internal Connection Manager) by looking
directly at the sw->config.enabled field which may be rather hard to
understand for the casual reader. For this reason introduce a wrapper
function with documentation that should make the intention more clear.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The Thunderbolt standard went through several major iterations, here
called generation. USB4, which will be based on Thunderbolt, will be
generation 4. Let userspace know the generation of the controller in
the devices in order to distinguish between Thunderbolt and USB4, so
it can be shown in various user interfaces.
Signed-off-by: Christian Kellner <christian@kellner.me>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The read is not needed as we overwrite the returned value in the next
line anyway so drop it.
Fixes: 3cdb9446a1 ("thunderbolt: Add support for Intel Ice Lake")
Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When lockdep is enabled, plugging Thunderbolt dock on Dominik's laptop
triggers following splat:
======================================================
WARNING: possible circular locking dependency detected
5.3.0-rc6+ #1 Tainted: G T
------------------------------------------------------
pool-/usr/lib/b/1258 is trying to acquire lock:
000000005ab0ad43 (pci_rescan_remove_lock){+.+.}, at: authorized_store+0xe8/0x210
but task is already holding lock:
00000000bfb796b5 (&tb->lock){+.+.}, at: authorized_store+0x7c/0x210
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&tb->lock){+.+.}:
__mutex_lock+0xac/0x9a0
tb_domain_add+0x2d/0x130
nhi_probe+0x1dd/0x330
pci_device_probe+0xd2/0x150
really_probe+0xee/0x280
driver_probe_device+0x50/0xc0
bus_for_each_drv+0x84/0xd0
__device_attach+0xe4/0x150
pci_bus_add_device+0x4e/0x70
pci_bus_add_devices+0x2e/0x66
pci_bus_add_devices+0x59/0x66
pci_bus_add_devices+0x59/0x66
enable_slot+0x344/0x450
acpiphp_check_bridge.part.0+0x119/0x150
acpiphp_hotplug_notify+0xaa/0x140
acpi_device_hotplug+0xa2/0x3f0
acpi_hotplug_work_fn+0x1a/0x30
process_one_work+0x234/0x580
worker_thread+0x50/0x3b0
kthread+0x10a/0x140
ret_from_fork+0x3a/0x50
-> #0 (pci_rescan_remove_lock){+.+.}:
__lock_acquire+0xe54/0x1ac0
lock_acquire+0xb8/0x1b0
__mutex_lock+0xac/0x9a0
authorized_store+0xe8/0x210
kernfs_fop_write+0x125/0x1b0
vfs_write+0xc2/0x1d0
ksys_write+0x6c/0xf0
do_syscall_64+0x50/0x180
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&tb->lock);
lock(pci_rescan_remove_lock);
lock(&tb->lock);
lock(pci_rescan_remove_lock);
*** DEADLOCK ***
5 locks held by pool-/usr/lib/b/1258:
#0: 000000003df1a1ad (&f->f_pos_lock){+.+.}, at: __fdget_pos+0x4d/0x60
#1: 0000000095a40b02 (sb_writers#6){.+.+}, at: vfs_write+0x185/0x1d0
#2: 0000000017a7d714 (&of->mutex){+.+.}, at: kernfs_fop_write+0xf2/0x1b0
#3: 000000004f262981 (kn->count#208){.+.+}, at: kernfs_fop_write+0xfa/0x1b0
#4: 00000000bfb796b5 (&tb->lock){+.+.}, at: authorized_store+0x7c/0x210
stack backtrace:
CPU: 0 PID: 1258 Comm: pool-/usr/lib/b Tainted: G T 5.3.0-rc6+ #1
On an system using ACPI hotplug the host router gets hotplugged first and then
the firmware starts sending notifications about connected devices so the above
scenario should not happen in reality. However, after taking a second
look at commit a03e828915 ("thunderbolt: Serialize PCIe tunnel
creation with PCI rescan") that introduced the locking, I don't think it
is actually correct. It may have cured the symptom but probably the real
root cause was somewhere closer to PCI stack and possibly is already
fixed with recent kernels. I also tried to reproduce the original issue
with the commit reverted but could not.
So to keep lockdep happy and the code bit less complex drop calls to
pci_lock_rescan_remove()/pci_unlock_rescan_remove() in
tb_switch_set_authorized() effectively reverting a03e828915.
Link: https://lkml.org/lkml/2019/8/30/513
Fixes: a03e828915 ("thunderbolt: Serialize PCIe tunnel creation with PCI rescan")
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When we discover existing DP tunnels the code checks whether DP IN
adapter port is enabled by calling tb_dp_port_is_enabled() before it
continues the discovery process. On Light Ridge (gen 1) controller
reading only the first dword of the DP IN config space causes subsequent
access to the same DP IN port path config space to fail or return
invalid data as can be seen in the below splat:
thunderbolt 0000:07:00.0: CFG_ERROR(0:d): Invalid config space or offset
Call Trace:
tb_cfg_read+0xb9/0xd0
__tb_path_deactivate_hop+0x98/0x210
tb_path_activate+0x228/0x7d0
tb_tunnel_restart+0x95/0x200
tb_handle_hotplug+0x30e/0x630
process_one_work+0x1b4/0x340
worker_thread+0x44/0x3d0
kthread+0xeb/0x120
? process_one_work+0x340/0x340
? kthread_park+0xa0/0xa0
ret_from_fork+0x1f/0x30
If both DP In adapter config dwords are read in one go the issue does
not reproduce. This is likely firmware bug but we can work it around by
always reading the two dwords in one go. There should be no harm for
other controllers either so can do it unconditionally.
Link: https://lkml.org/lkml/2019/8/28/160
Reported-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The Thunderbolt controller is integrated into the Ice Lake CPU itself
and requires special flows to power it on and off using force power bit
in NHI VSEC registers. Runtime PM (RTD3) and Sx flows also differ from
the discrete solutions. Now the firmware notifies the driver whether
RTD3 entry or exit are possible. The driver is responsible of sending
Go2Sx command through link controller mailbox when system enters Sx
states (suspend-to-mem/disk). Rest of the ICM firwmare flows follow
Titan Ridge.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Ice Lake Thunderbolt controller NVM firmware is part of the BIOS image
which means it is not writable through the DMA port anymore. However, we
can still read it so we can keep nvm_version and active parts of NVM.
This way users still can find out the active NVM version and other
potentially useful information directly from Linux.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Thunderbolt host routers may not always contain DROM that includes
device identification information. This is mostly needed for Ice Lake
systems but some Falcon Ridge controllers on PCs also do not have DROM.
In that case hide the identification attributes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
There are two ways to mark a port as unimplemented. Typical way is to
return port type as TB_TYPE_INACTIVE when its config space is read.
Alternatively if the port is not physically present (such as ports 10
and 11 in ICL) reading from port config space returns
TB_CFG_ERROR_INVALID_CONFIG_SPACE instead. Currently the driver bails
out from adding the switch if it receives any error during port
inititialization which is wrong.
Handle this properly and just leave the port as TB_TYPE_INACTIVE before
continuing to the next port.
This also allows us to get rid of special casing for Light Ridge port 5
in eeprom.c.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
The register access should be using 32-bit reads/writes according to the
datasheet. With the previous generation hardware 16-bit writes have been
working but starting with ICL this is not the case anymore so fix
producer/consumer register update to use correct width register address.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
This is depends on the controller and on the platform/CPU we are
running. Move it to struct icm so we can set it per controller.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
PCIe tunnel path indices got mixed up when we added support for tunnels
between switches that are not adjacent. This did not affect the
functionality as it is just an index but fix it now nevertheless to make
the code easier to understand.
Reported-by: Rajmohan Mani <rajmohan.mani@intel.com>
Fixes: 8c7acaaf02 ("thunderbolt: Extend tunnel creation to more than 2 adjacent switches")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
%*pEp (without "h" or "o") is a no-op. This string could contain
arbitrary (non-NULL) characters, so we do want escaping. Use %*pE like
every other caller.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use device_property_count_uXX() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
There is an arbitrary difference between the prototypes of
bus_find_device() and class_find_device() preventing their callers
from passing the same pair of data and match() arguments to both of
them, which is the const qualifier used in the prototype of
class_find_device(). If that qualifier is also used in the
bus_find_device() prototype, it will be possible to pass the same
match() callback function to both bus_find_device() and
class_find_device(), which will allow some optimizations to be made in
order to avoid code duplication going forward. Also with that, constify
the "data" parameter as it is passed as a const to the match function.
For this reason, change the prototype of bus_find_device() to match
the prototype of class_find_device() and adjust its callers to use the
const qualifier in accordance with the new prototype of it.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Kershner <david.kershner@unisys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: rafael@kernel.org
Acked-by: Corey Minyard <minyard@acm.org>
Acked-by: David Kershner <david.kershner@unisys.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When starting ICM firmware on Apple systems we need to perform CIO reset
as part of the flow. However, it turns out that the reset register has
changed to another location in Titan Ridge.
Fix this by introducing ->cio_reset() callback with corresponding
implementations for Alpine and Titan Ridge.
Fixes: c4630d6ae6 ("thunderbolt: Start firmware on Titan Ridge Apple systems")
Reported-by: Peter Bowen <pzb@amazon.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When a device is authorized from userspace by writing to authorized
attribute we first take the domain lock and then runtime resume the
device in question. There are two issues with this.
First is that the device connected notifications are blocked during this
time which means we get them only after the authorization operation is
complete. Because of this the authorization needed flag from the
firmware notification is not reflecting the real authorization status
anymore. So what happens is that the "authorized" keeps returning 0 even
if the device was already authorized properly.
Second issue is that each time the controller is runtime resumed the
connection_id field of device connected notification may be different
than in the previous resume. We need to use the latest connection_id
otherwise the firmware rejects the authorization command.
Fix these by moving runtime resume operations to happen before the
domain lock is taken, and waiting for the updated device connected
notification from the firmware before we allow runtime resume of a
device to complete.
While there add missing locking to tb_switch_nvm_read().
Fixes: 09f11b6c99 ("thunderbolt: Take domain lock in switch sysfs attribute callbacks")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "real" big set of char/misc driver patches for 5.2-rc1
Loads of different driver subsystem stuff in here, all over the places:
- thunderbolt driver updates
- habanalabs driver updates
- nvmem driver updates
- extcon driver updates
- intel_th driver updates
- mei driver updates
- coresight driver updates
- soundwire driver cleanups and updates
- fastrpc driver updates
- other minor driver updates
- chardev minor fixups
Feels like this tree is getting to be a dumping ground of "small driver
subsystems" these days. Which is fine with me, if it makes things
easier for those subsystem maintainers.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHE2w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvyQCYj5vSHQ88yEU+bzwGzQQLOBWYIwCgm5Iku0Y3
f6V3MvRffg4qUp3cGbU=
=R37j
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.2-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc update part 2 from Greg KH:
"Here is the "real" big set of char/misc driver patches for 5.2-rc1
Loads of different driver subsystem stuff in here, all over the places:
- thunderbolt driver updates
- habanalabs driver updates
- nvmem driver updates
- extcon driver updates
- intel_th driver updates
- mei driver updates
- coresight driver updates
- soundwire driver cleanups and updates
- fastrpc driver updates
- other minor driver updates
- chardev minor fixups
Feels like this tree is getting to be a dumping ground of "small
driver subsystems" these days. Which is fine with me, if it makes
things easier for those subsystem maintainers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.2-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
intel_th: msu: Add current window tracking
intel_th: msu: Add a sysfs attribute to trigger window switch
intel_th: msu: Correct the block wrap detection
intel_th: Add switch triggering support
intel_th: gth: Factor out trace start/stop
intel_th: msu: Factor out pipeline draining
intel_th: msu: Switch over to scatterlist
intel_th: msu: Replace open-coded list_{first,last,next}_entry variants
intel_th: Only report useful IRQs to subdevices
intel_th: msu: Start handling IRQs
intel_th: pci: Use MSI interrupt signalling
intel_th: Communicate IRQ via resource
intel_th: Add "rtit" source device
intel_th: Skip subdevices if their MMIO is missing
intel_th: Rework resource passing between glue layers and core
intel_th: SPDX-ify the documentation
intel_th: msu: Fix single mode with IOMMU
coresight: funnel: Support static funnel
dt-bindings: arm: coresight: Unify funnel DT binding
coresight: replicator: Add new device id for static replicator
...
Clang warns:
drivers/thunderbolt/tunnel.c:504:17: warning: implicit truncation from
'int' to bit-field changes value from 5 to -3
[-Wbitfield-constant-conversion]
path->priority = 5;
^ ~
1 warning generated.
The priority member in struct tb_path is only ever assigned a positive
number:
$ rg -n priority drivers/thunderbolt/path.c
drivers/thunderbolt/tunnel.c:99: path->priority = 3;
drivers/thunderbolt/tunnel.c:308: path->priority = 2;
drivers/thunderbolt/tunnel.c:323: path->priority = 1;
drivers/thunderbolt/tunnel.c:504: path->priority = 5;
Furthermore, that value is only assigned to an unsigned integer in
tb_path_activate (the priority member in struct tb_regs_hop).
Fixes: 44242d6c97 ("thunderbolt: Add support for DMA tunnels")
Link: https://github.com/ClangBuiltLinux/linux/issues/454
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The flags field in 'struct shash_desc' never actually does anything.
The only ostensibly supported flag is CRYPTO_TFM_REQ_MAY_SLEEP.
However, no shash algorithm ever sleeps, making this flag a no-op.
With this being the case, inevitably some users who can't sleep wrongly
pass MAY_SLEEP. These would all need to be fixed if any shash algorithm
actually started sleeping. For example, the shash_ahash_*() functions,
which wrap a shash algorithm with the ahash API, pass through MAY_SLEEP
from the ahash API to the shash API. However, the shash functions are
called under kmap_atomic(), so actually they're assumed to never sleep.
Even if it turns out that some users do need preemption points while
hashing large buffers, we could easily provide a helper function
crypto_shash_update_large() which divides the data into smaller chunks
and calls crypto_shash_update() and cond_resched() for each chunk. It's
not necessary to have a flag in 'struct shash_desc', nor is it necessary
to make individual shash algorithms aware of this at all.
Therefore, remove shash_desc::flags, and document that the
crypto_shash_*() functions can be called from any context.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Titan Ridge flow to start the firmware is the same as Alpine Ridge so we
can do the same on Titan Ridge based Apple systems.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
While tb_dump_hop() prints out necessary information it is in format
that is quite hard to read from the logs especially when one needs to
follow the path to see that the setup is correct.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that the driver can handle every possible tunnel types there is no
point to log everything as info level so turn these to happen at debug
level instead.
While at it remove duplicated tunnel activation log message
(tb_tunnel_activate() calls tb_tunnel_restart() which print the same
message) and add one missing '\n' termination.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The printing macros do not modify the passed object so make them
const. While there make tb_route() to take const parameter as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Two domains (hosts) can be connected through a Thunderbolt cable and in
that case they can start software services such as networking over the
high-speed DMA paths. Now that we have all the basic building blocks in
place to create DMA tunnels over the Thunderbolt fabric we can add this
support to the software connection manager as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to detect possible connections to other domains we need to be
able to find out why tb_switch_alloc() fails so make it return ERR_PTR()
instead. This allows the caller to differentiate between errors such as
-ENOMEM which comes from the kernel and for instance -EIO which comes
from the hardware when trying to access the possible switch.
Convert all the current call sites to handle this properly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In addition to PCIe and Display Port tunnels it is also possible to
create tunnels that forward DMA traffic from the host interface adapter
(NHI) to a NULL port that is connected to another domain through a
Thunderbolt cable. These tunnels can be used to carry software messages
such as networking packets.
To support this we introduce another tunnel type (TB_TUNNEL_DMA) that
supports paths from NHI to NULL port and back.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently ICM has been handling XDomain UUID exchange so there was no
need to have it in the driver yet. However, since now we are going to
add the same capabilities to the software connection manager it needs to
be handled properly.
For this reason modify the driver XDomain protocol handling so that if
the remote domain UUID is not filled in the core will query it first and
only then start the normal property exchange flow.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We run all XDomain requests during discovery in tb->wq and since it only
runs one work at the time it means that sending back reply to the other
domain may be delayed too much depending whether there is an active
XDomain discovery request running.
To make sure we can send reply to the other domain as soon as possible
run tb_xdp_handle_request() in system workqueue instead. Since the
device can be hot-removed in the middle we need to make sure the domain
structure is still around when the function is run so increase reference
count before we schedule the reply work.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that we have capability to discover existing tunnels during driver
load there is no point tearing down tunnels when the driver gets
unloaded. Instead we can just leave them running. If user disconnects
devices while there is no Thunderbolt driver loaded, tunneled protocol
hotplug happens and is handled by the corresponding driver (pciehp in
case of PCIe tunnel, GFX driver in case of DP tunnel).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Display Port tunnels are somewhat more complex than PCIe tunnels as it
requires 3 tunnels (AUX Rx/Tx and Video). In addition we are not
supposed to create the tunnels immediately when a DP OUT is enumerated.
Instead we need to wait until we get hotplug event to that adapter port
or check if the port has HPD set before tunnels can be established. This
adds Display Port tunneling support to the software connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
NFC (non flow control) credits is actually 20-bit field so update
tb_port_add_nfc_credits() to handle this properly. This allows us to set
NFC credits for Display Port path in subsequent patches.
Also make sure the function does not update the hardware if the
underlying switch is already unplugged.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We will be needing these routines to find Display Port adapters as well
so modify them to take port type as the second parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The only way to expand Thunderbolt topology is through the NULL adapter
ports (typically ports 1, 2, 3 and 4). There is no point handling
Thunderbolt hotplug events on any other port.
Add a helper function (tb_port_is_null()) that can be used to determine
if the port is NULL port, and use it in software connection manager code
when hotplug event is handled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently the software connection manager (tb.c) has only supported
creating a single PCIe tunnel, no PCIe device daisy chaining has been
supported so far. This updates the software connection manager so that
it now can create PCIe tunnels for full chain of six devices.
Because PCIe allows DMA and opens possibility for DMA attacks we change
security level to "user" meaning that PCIe tunneling requires that the
userspace authorizes the devices first. This makes it possible to block
PCIe tunneling completely while still allowing other types of tunnels to
be automatically created.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In Apple Macs the boot firmware (EFI) connects all devices automatically
when the system is started, before it hands over to the OS. Instead of
ignoring we discover all those PCIe tunnels and record them using our
internal structures, just like we do when a device is connected after
the OS is already up.
By doing this we can properly tear down tunnels when devices are
disconnected. Also this allows us to resume the existing tunnels after
system suspend/resume cycle.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
State of the connected devices and tunnel configuration is not known
during resume. For example some paths may not be complete anymore if the
user has unplugged the related devices. So instead of marking all paths
as inactive we go ahead and deactivate them explicitly before we restart
them.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that we can allocate hop IDs per port on a path, we can take
advantage of this and create tunnels covering longer paths than just
between two adjacent switches. PCIe actually does not need this as it
is typically a daisy chain between two adjacent switches but this way we
do not need to hard-code creation of the tunnel.
While there add name to struct tb_path to make debugging easier, and
update kernel-doc comments.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We need to be able to walk from one port to another when we are creating
paths where there are multiple switches between two ports. For this
reason introduce a new function tb_next_port_on_path().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Currently the driver only assigns remote port for the primary port if in
case of dual link. This makes things such as walking from one port to
another more complex than necessary because the code needs to change
from secondary to primary port if the path that is established is
created using secondary links.
In order to always assign both remote pointers we need to prevent the
scanning code from following the secondary link. Failing to do that
might cause problems as the same switch may be enumerated twice (or
removed in case of unplug). Handle that properly by introducing a new
function tb_port_has_remote() that returns true only for the primary
port. We also update tb_is_upstream_port() to support both dual link
ports, make it take const port pointer and move it below
tb_upstream_port() to keep similar functions close.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Each port has a separate path configuration space that is used for
finding the next hop (switch) in the path. HopID is an index to this
configuration space. HopIDs 0 - 7 are reserved by the protocol.
In order to get next available HopID for each direction we provide two
pairs of helper functions that can be used to allocate and release
HopIDs for a given port.
While there remove obsolete TODO comment.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
To be able to tunnel non-PCIe traffic, separate tunnel functionality
into generic and PCIe specific parts. Rename struct tb_pci_tunnel to
tb_tunnel, and make it hold an array of paths instead of just two.
Update all the tunneling functions to take this structure as parameter.
We also move tb_pci_port_active() to switch.c (and rename it) where we
will be keeping all port and switch related functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to tunnel non-PCIe traffic as well rename tunnel_pci.[ch] to
tunnel.[ch] to reflect this fact. No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The adapter specific capability either is there or not if the port does
not hold an adapter. Instead of always finding it on-demand we read the
offset just once when the port is initialized.
While there we update the struct port documentation to follow kernel-doc
format.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We need to wait until all buffers have been drained before the path can
be considered disabled. Do this for every hop in a path.
This adds another bit field to struct tb_regs_hop even if we are trying
to get rid of them but we can clean them up another day.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Thunderbolt 2 devices and beyond link controller needs to be notified
when a switch is going to be suspended by setting bit 31 in LC_SX_CTRL
register. Add this functionality to the software connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Thunderbolt 2 devices and beyond need to have additional bits set in
link controller specific registers. This includes two bits in LC_SX_CTRL
that tell the link controller which lane is connected and whether it is
upstream facing or not.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We will be adding more link controller functionality in subsequent
patches and it does not make sense to keep all that in switch.c, so
separate LC functionality into its own file.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Light Ridge has an issue where reading the next capability pointer
location in port config space the read data is not cleared. It is fine
to read capabilities each after another so only thing we need to do is
to make sure we issue dummy read after tb_port_find_cap() is finished to
avoid the issue in next read.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Light Ridge and Eagle Ridge both need to have TMU access enabled before
port space can be fully accessed so make sure it happens on those. This
allows us to get rid of the offset quirk in tb_port_find_cap().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Maximum depth in Thunderbolt topology is 6 so make sure it is not
possible to allocate switches that exceed the depth limit.
While at it update tb_switch_alloc() to use upper/lower_32_bits()
following tb_switch_alloc_safe_mode().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
switch_lock was introduced because it allowed serialization of device
authorization requests from userspace without need to take the big
domain lock (tb->lock). This was fine because device authorization with
ICM is just one command that is sent to the firmware. Now that we start
to handle all tunneling in the driver switch_lock is not enough because
we need to walk over the topology to establish paths.
For this reason drop switch_lock from the driver completely in favour of
big domain lock.
There is one complication, though. If userspace is waiting for the lock
in tb_switch_set_authorized(), it keeps the device_del() from removing
the sysfs attribute because it waits for active users to release the
attribute first which leads into following splat:
INFO: task kworker/u8:3:73 blocked for more than 61 seconds.
Tainted: G W 5.1.0-rc1+ #244
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u8:3 D12976 73 2 0x80000000
Workqueue: thunderbolt0 tb_handle_hotplug [thunderbolt]
Call Trace:
? __schedule+0x2e5/0x740
? _raw_spin_lock_irqsave+0x12/0x40
? prepare_to_wait_event+0xc5/0x160
schedule+0x2d/0x80
__kernfs_remove.part.17+0x183/0x1f0
? finish_wait+0x80/0x80
kernfs_remove_by_name_ns+0x4a/0x90
remove_files.isra.1+0x2b/0x60
sysfs_remove_group+0x38/0x80
sysfs_remove_groups+0x24/0x40
device_remove_attrs+0x3d/0x70
device_del+0x14c/0x360
device_unregister+0x15/0x50
tb_switch_remove+0x9e/0x1d0 [thunderbolt]
tb_handle_hotplug+0x119/0x5a0 [thunderbolt]
? process_one_work+0x1b7/0x420
process_one_work+0x1b7/0x420
worker_thread+0x37/0x380
? _raw_spin_unlock_irqrestore+0xf/0x30
? process_one_work+0x420/0x420
kthread+0x118/0x130
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x35/0x40
We deal this by following what network stack did for some of their
attributes and use mutex_trylock() with restart_syscall(). This makes
userspace release the attribute allowing sysfs attribute removal to
progress before the write is restarted and eventually fail when the
attribute is removed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If switch is already disconnected there is no point sending it commands
and waiting for timeout. Instead in that case return error immediately.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
tb_switch_find_by_route() does the same already so use it instead and
remove duplicated get_switch_at_route().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
This field is not used anywhere so remove it.
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
uuid in add_switch is allocted via kmemdup which can fail. The patch
logs the error and cleans up the allocated memory for switch.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
No check is enforced for the return value of kzalloc,
which may lead to NULL-pointer dereference.
The patch fixes this issue.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
kmemdup can fail and return a NULL pointer. The patch modifies the
signature of tb_xdp_schedule_request and passes the failure error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In enumerate_services, ida_simple_get on failure can return an error and
leaks memory. The patch ensures that the dev_set_name is set on non
failure cases, and releases memory during failure.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Memory allocated via kmemdup might fail and return a NULL pointer.
This patch adds a check on the return value of kmemdup and passes the
error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
kmemdup may fail and return NULL. The fix adds a check and returns
NULL in case it fails to avoid NULL pointer dereferecen.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In case kzalloc fails, the fix releases resources and returns
-ENOMEM to avoid the NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Recent systems with Thunderbolt ports may support IOMMU natively. In
practice this means that Thunderbolt connected devices are placed behind
an IOMMU during the whole time it is connected (including during boot)
making Thunderbolt security levels redundant. This is called Kernel DMA
protection [1] by Microsoft.
Some of these systems still have Thunderbolt security level set to
"user" in order to support OS downgrade (the older version of the OS
might not support IOMMU based DMA protection so connecting a device
still relies on user approval).
Export this information to userspace by introducing a new sysfs
attribute (iommu_dma_protection). Based on it userspace tools can make
more accurate decision whether or not authorize the connected device.
In addition update Thunderbolt documentation regarding IOMMU based DMA
protection.
[1] https://docs.microsoft.com/en-us/windows/security/information-protection/kernel-dma-protection-for-thunderbolt
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
During NVM upgrade process the host router is hot-removed for a short
while. During this time it is possible that the root port is moved into
D3cold which would be fine if the root port could trigger PME on itself.
However, many systems actually do not implement it so what happens is
that the root port goes into D3cold and never wakes up unless userspace
does PCI config space access, such as running 'lscpi'.
For this reason we explicitly prevent the root port from runtime
suspending during NVM upgrade.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel has done pretty major changes to the driver and we continue to do
so in the future as well. Add Intel as copyright holder of the files we
have done changes.
While there drop "Cactus Ridge" from the headers because this driver
works also with other Thunderbolt controllers.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This gets rid of the licence boilerplate duplicated in each file. While
there fix doubled space in domain.c author line.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous patch made the driver less verbose meanining that all the
switch structures and ports are now logged as debug level. However, we
have been missing similar output that USB for intance prints when a new
USB device is connected and disconnected. This information is useful for
end users as well as developers because it immediately shows the actual
device that was connected.
This patch adds printing of the actual connected devices to the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the driver logs quite a lot to the system message buffer even
when doing normal operations. This information is not useful for
ordinary users and might even annoy some.
For this reason convert most of the logs at info level to happen at
debug level instead. The nice output formatting is untouched.
Logging can be easily re-enabled by passing "thunderbolt.dyndbg" in the
kernel command line (or using the corresponding control file runtime).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_pool_destroy() already takes NULL pointer into account so there is
no need to check that again in tb_ctl_free().
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
[mw: reword commit log a bit]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IOMMU is enabled and Thunderbolt driver is built into the kernel
image, it will be probed before IOMMUs are attached to the PCI bus.
Because of this DMA mappings the driver does will not go through IOMMU
and start failing right after IOMMUs are enabled.
For this reason move the Thunderbolt driver initialization happen at
rootfs level.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is a long chain of devices connected when the driver is loaded
ICM sends device connected event for each and those are put to tb->wq
for later processing. Now if the driver gets unloaded in the middle, so
that the work queue is not yet empty it gets flushed by tb_domain_stop().
However, by that time the root switch is already removed so the driver
crashes when it tries to dereference it in ICM event handling callbacks.
Fix this by checking whether the root switch is already removed. If it
is we know that the domain is stopped and we should merely skip handling
the event.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Thunderbolt host controller is set to RTD3 mode (Runtime D3) it is
present all the time. Because of this it is important to runtime suspend
the controller whenever possible. In case of ICM we have following rules
which all needs to be true before the host controller can be put to D3:
- The controller firmware reports to support RTD3
- All the connected devices announce support for RTD3
- There is no active XDomain connection
Implement this using standard Linux runtime PM APIs so that when all the
children devices are runtime suspended, the Thunderbolt host controller
PCI device is runtime suspended as well. The ICM firmware then starts
powering down power domains towards RTD3 but it can prevent this if it
detects that there is an active Display Port stream (this is not visible
to the software, though).
The Thunderbolt host controller will be runtime resumed either when
there is a remote wake event (device is connected or disconnected), or
when there is access from userspace that requires hardware access.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'approved' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'approved' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct way to put the ICM into suspend state is to send it
NHI_MAILBOX_DRV_UNLOADS mailbox command. NHI_MAILBOX_SAVE_DEVS is not
needed on Intel Titan Ridge so we can skip it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the connection manager implementation needs to touch the domain
structures it ought to take the lock itself. Currently only ICM
implements these hooks and it does not need the lock because we there
will be no notifications before driver ready message is sent to it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This command is not really fast and can make resume time slower. We only
need to get route again if the link was changed and during initial
device connected message.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI defaults to 32-bit DMA mask but this device is capable of full
64-bit addressing, so make sure we first try 64-bit DMA mask before
falling back to the default 32-bit.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes small variable name typo and the associated
checkpatch spelling warning.
Signed-off-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 9aaa3b8b4c ("thunderbolt: Add support for preboot ACL")
introduced boot_acl attribute but missed the fact that now userspace
needs to poll the attribute constantly to find out whether it has
changed or not. Fix this by sending notification to the userspace
whenever the boot_acl attribute is changed.
Fixes: 9aaa3b8b4c ("thunderbolt: Add support for preboot ACL")
Reported-and-tested-by: Christian Kellner <christian@kellner.me>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Christian Kellner <christian@kellner.me>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the boot ACL entry is already NULL we should not fill in the upper
two DWs with 0xfffffffff. Otherwise they are not shown as empty entries
when the sysfs attribute is read.
Fixes: 9aaa3b8b4c ("thunderbolt: Add support for preboot ACL")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Lenovo ThinkPad Yoga 370 (and possibly some other Lenovo models as
well) the Thunderbolt host controller sometimes comes up in such way
that the ICM firmware is not running properly. This is most likely an
issue in BIOS/firmware but as side-effect driver crashes the kernel due
to NULL pointer dereference:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000980
IP: pci_write_config_dword+0x5/0x20
Call Trace:
pcie2cio_write+0x3b/0x70 [thunderbolt]
icm_driver_ready+0x168/0x260 [thunderbolt]
? tb_ctl_start+0x50/0x70 [thunderbolt]
tb_domain_add+0x73/0xf0 [thunderbolt]
nhi_probe+0x182/0x300 [thunderbolt]
local_pci_probe+0x42/0xa0
? pci_match_device+0xd9/0x100
pci_device_probe+0x146/0x1b0
driver_probe_device+0x315/0x480
...
Instead of crashing update the driver to bail out gracefully if we
encounter such situation.
Fixes: f67cf49117 ("thunderbolt: Add support for Internal Connection Manager (ICM)")
Reported-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Cc: stable@vger.kernel.org
Intel Titan Ridge is the next Thunderbolt 3 controller. The ICM firmware
message format in Titan Ridge differs from Falcon Ridge and Alpine Ridge
somewhat because it is using route strings addressing devices. In
addition to that the DMA port of 4-channel (two port) controller is in
different port number than the previous controllers. There are some
other minor differences as well.
This patch add support for Intel Titan Ridge and the new ICM firmware
message format.
Signed-off-by: Radion Mirchevsky <radion.mirchevsky@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This new security level works so that it creates one PCIe tunnel to the
connected Thunderbolt dock, removing PCIe links downstream of the dock.
This leaves only the internal USB controller visible.
Display Port tunnels are created normally.
While there make sure security sysfs attribute returns "unknown" for any
future security level.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Preboot ACL is a mechanism that allows connecting Thunderbolt devices
boot time in more secure way than the legacy Thunderbolt boot support.
As with the legacy boot option, this also needs to be enabled from the
BIOS before booting is allowed. Difference to the legacy mode is that
the userspace software explicitly adds device UUIDs by sending a special
message to the ICM firmware. Only the devices listed in the boot ACL are
connected automatically during the boot. This works in both "user" and
"secure" security levels.
We implement this in Linux by exposing a new sysfs attribute (boot_acl)
below each Thunderbolt domain. The userspace software can then update
the full list as needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
In various cases, Thunderbolt device can be connected by ICM on boot
without waiting for approval from user. Most cases are related to
OEM-specific BIOS configurations. This information is interesting for
user-space as if the device isn't in SW ACL, it may create a friction in
the user experience where the device is automatically authorized if it's
connected on boot but requires an explicit user action if connected
after OS is up. User-space can use this information to suggest adding
the device to SW ACL for auto-authorization on later connections.
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Intel Titan Ridge uses slightly different format for ICM driver ready
response, so add a new ->driver_ready() callback to struct icm and move
the existing handling to a separate function which we then use in Falcon
Ridge and Alpine Ridge.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
We will be using this from Titan Ridge support code as well so make it
constant.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
This is needed by the new ICM interface to find xdomains by route string
instead of link and depth.
While there update existing tb_xdomain_find_* functions to use
tb_xdomain_get() instead of open-coding the same.
Signed-off-by: Radion Mirchevsky <radion.mirchevsky@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
With the new ICM messaging there is need for find switch by route string
instead of link and depth. Add new function that makes it possible.
Signed-off-by: Radion Mirchevsky <radion.mirchevsky@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Sometimes there is need for increasing reference count of a switch as
well. This also follows what we have for xdomains.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Use correct name in kernel-doc of tb_switch_find_by_uuid().
Signed-off-by: Radion Mirchevsky <radion.mirchevsky@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
The newer ICM will not use link and depth to address devices. Instead it
uses route strings. In order to take advantage of the existing code
factor out common operations so that we can use the same functions with
the new ICM as well.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
The ICM firmware rejects devices if the maximum topology limit is
exceeded (more than 6 devices are connected). If that happens just log a
message to the kernel message buffer and bail out.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Sometimes during cold boot ICM has not yet authenticated the active NVM
image leading to timeout and failing the driver probe. Allow ICM to take
some more time and increase the timeout to 3 seconds before we give up.
While there fix icm_firmware_init() to return the real error code
without overwriting it with -ENODEV.
Fixes: f67cf49117 ("thunderbolt: Add support for Internal Connection Manager (ICM)")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@vger.kernel.org
In some case reading root switch config space takes longer than what we
are currently waiting in the driver resulting timeout and failure.
Increase number of retries to allow some more time for the root switch
config space to become accesssible.
Also log an error if the timeout is exceeded so we know why the driver
probe failed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
If the Thunderbolt domain adding fails for some reason we currently
always return -EIO instead of the real error code. To make debugging
easier return the actual error code instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
If the system is suspended and user disconnects cable to another host
and connects it to a Thunderbolt device instead we get a warning from
driver core about adding duplicate sysfs attribute and adding the new
device fails.
Handle this properly so that we first remove the existing XDomain
connection before adding new devices.
Fixes: d1ff70241a ("thunderbolt: Add support for XDomain discovery protocol")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@vger.kernel.org
We need to make sure a new PCIe tunnel is not created in a middle of
previous PCI rescan because otherwise the rescan code might find too
much and fail to reconfigure devices properly. This is important when
native PCIe hotplug is used. In BIOS assisted hotplug there should be no
such issue.
Fixes: f67cf49117 ("thunderbolt: Add support for Internal Connection Manager (ICM)")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
The driver misses implementation of PM hook that undoes what
->freeze_noirq() does after the hibernation image is created. This means
the control channel is not resumed properly and the Thunderbolt bus
becomes useless in later stages of hibernation (when the image is stored
or if the operation fails).
Fix this by pointing ->thaw_noirq to driver nhi_resume_noirq(). This
makes sure the control channel is resumed properly.
Fixes: 23dd5bb49d ("thunderbolt: Add suspend/hibernate support")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@vger.kernel.org
When ring enters polling mode we are expected to mask the ring interrupt
before the callback is called. However, the current code actually
unmasks it probably because of a copy-paste mistake.
Mask the interrupt properly from now on.
Fixes: 4ffe722eef ("thunderbolt: Add polling mode for rings")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char/misc and other driver subsystem patches for
4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
Note, there will be a merge conflict in drivers/misc/lkdtm_core.c when
merging to your tree as one lkdtm patch came in through the perf tree as
well as this one. The resolution is to take the const change that this
tree provides.
All of these have been in linux-next for quite a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWg2Lnw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymTUwCgwp46+I8yPlgDH8oe5TxyyJnpdHQAn1XW0i+a
sBi6WS87In5v1QO1Rgfc
=dH2a
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem patches
for 4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
All of these have been in linux-next for quite a while with no
reported issues"
* tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
VME: Return -EBUSY when DMA list in use
w1: keep balance of mutex locks and refcnts
MAINTAINERS: Update VME subsystem tree.
nvmem: sunxi-sid: add support for A64/H5's SID controller
nvmem: imx-ocotp: Update module description
nvmem: imx-ocotp: Enable i.MX7D OTP write support
nvmem: imx-ocotp: Add i.MX7D timing write clock setup support
nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function
nvmem: imx-ocotp: Add support for banked OTP addressing
nvmem: imx-ocotp: Pass parameters via a struct
nvmem: imx-ocotp: Restrict OTP write to IMX6 processors
nvmem: uniphier: add UniPhier eFuse driver
dt-bindings: nvmem: add description for UniPhier eFuse
nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset
nvmem: qfprom: fix different address space warnings of sparse
nvmem: mtk-efuse: fix different address space warnings of sparse
nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it
nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it
thunderbolt: tb: fix use after free in tb_activate_pcie_devices
MAINTAINERS: Add git tree for Thunderbolt development
...
Add a ̣̣continue statement in order to avoid using a previously
free'd pointer tunnel in list_add.
Addresses-Coverity-ID: 1415336
Fixes: 9d3cce0b61 ("thunderbolt: Introduce thunderbolt bus and connection manager")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9a03c3d398 ("thunderbolt: Fix a couple right shifting to zero
bugs") revealed an issue that was previously hidden because we never
actually compared received XDomain message sequence numbers properly.
The idea with these sequence numbers is that the responding host uses
the same sequence number that was in the request packet which we can
then check at the requesting host.
However, testing against macOS it looks like it does not follow this but
instead uses some other logic. Windows driver on the other hand handles
it the same way than Linux.
In order to be able to talk to macOS again, fix this so that we drop the
whole sequence number check. This effectively works exactly the same
than it worked before the aforementioned commit. This also follows the
logic the original P2P networking code used.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problematic code looks like this:
res_seq = res_hdr->xd_hdr.length_sn & TB_XDOMAIN_SN_MASK;
res_seq >>= TB_XDOMAIN_SN_SHIFT;
TB_XDOMAIN_SN_SHIFT is 27, and right shifting a u8 27 bits is always
going to result in zero. The fix is to declare these variables as u32.
Fixes: d1ff70241a ("thunderbolt: Add support for XDomain discovery protocol")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 0day kbuild robot reports following crash:
BUG: unable to handle kernel NULL pointer dereference at 00000004
IP: tb_property_find+0xe/0x41
*pde = 00000000
Oops: 0000 [#1]
CPU: 0 PID: 1 Comm: swapper Not tainted 4.14.0-rc1-00741-ge69b6c0 #412
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
task: 89c80000 task.stack: 89c7c000
EIP: tb_property_find+0xe/0x41
EFLAGS: 00210246 CPU: 0
EAX: 00000000 EBX: 7a368f47 ECX: 00000044 EDX: 7a368f47
ESI: 8851d340 EDI: 7a368f47 EBP: 89c7df0c ESP: 89c7defc
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000004 CR3: 027a2000 CR4: 00000690
Call Trace:
tb_register_property_dir+0x49/0xb9
? cdc_mbim_driver_init+0x1b/0x1b
tbnet_init+0x77/0x9f
? cdc_mbim_driver_init+0x1b/0x1b
do_one_initcall+0x7e/0x145
? parse_args+0x10c/0x1b3
? kernel_init_freeable+0xbe/0x159
kernel_init_freeable+0xd1/0x159
? rest_init+0x110/0x110
kernel_init+0xd/0xd0
ret_from_fork+0x19/0x30
The reason is that both Thunderbolt bus and thunderbolt-net are build
into the kernel image, and the latter is linked first because
drivers/net comes before drivers/thunderbolt. Since both use
module_init() thunderbolt-net ends up calling Thunderbolt bus functions
too early triggering the above crash.
Fix this by moving Thunderbolt bus initialization to happen earlier to
make sure all the data structures are ready when Thunderbolt service
drivers are initialized. To be on the safe side also add a check for
properly initialized xdomain_property_dir to tb_register_property_dir().
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thunderbolt services should not care which HopID (ring) they use for
sending and receiving packets over the high-speed DMA path, so make
tb_ring_alloc_rx() and tb_ring_alloc_tx() accept negative HopID. This
means that the NHI will allocate next available HopID for the caller
automatically.
These HopIDs will be allocated from the range which is not reserved for
the Thunderbolt protocol (8 .. hop_count - 1).
The allocated HopID can be retrieved from ring->hop field after the ring
has been allocated successfully if needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support things like networking over Thunderbolt cable, there
needs to be a way to switch the ring to a mode where it can be polled
with the interrupt masked. We implement such mode so that the caller can
allocate a ring by passing pointer to a function that is then called
when an interrupt is triggered. Completed frames can be fetched using
tb_ring_poll() and the interrupt can be re-enabled when the caller is
finished with polling by using tb_ring_poll_complete().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed because ring polling functionality can be called from
atomic contexts when networking and other high-speed traffic is
transferred over a Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it possible to enqueue frames also from atomic context which
is needed for example, when networking packets are sent over a
Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Thunderbolt service driver might need to check if there was an error
with the descriptor when in frame mode. We also add two Rx specific
error flags RING_DESC_CRC_ERROR and RING_DESC_BUFFER_OVERRUN.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are used by Thunderbolt services to send and receive frames over
the high-speed DMA rings.
We also put the functions to tb_ namespace to make sure we do not
collide with others and add missing kernel-doc comments for the exported
functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When high-speed DMA paths are used to transfer arbitrary data over a
Thunderbolt link, DMA rings should be in frame mode instead of raw mode.
The latter is used by the control channel (ring 0). In frame mode each
data frame can hold up to 4kB payload.
This patch modifies the DMA ring code to allow configuring a ring to be
in frame mode by passing a new flag (RING_FLAG_FRAME) to the ring when
it is allocated. In addition there might be need to enable end-to-end
(E2E) workaround for the ring to prevent losing Rx frames in certain
situations. We add another flag (RING_FLAG_E2E) that can be used for
this purpose.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will keep the interrupt delivery rate reasonable. The value used
here (128 us) is a recommendation from the hardware people.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When two hosts are connected over a Thunderbolt cable, there is a
protocol they can use to communicate capabilities supported by the host.
The discovery protocol uses automatically configured control channel
(ring 0) and is build on top of request/response transactions using
special XDomain primitives provided by the Thunderbolt base protocol.
The capabilities consists of a root directory block of basic properties
used for identification of the host, and then there can be zero or more
directories each describing a Thunderbolt service and its capabilities.
Once both sides have discovered what is supported the two hosts can
setup high-speed DMA paths and transfer data to the other side using
whatever protocol was agreed based on the properties. The software
protocol used to communicate which DMA paths to enable is service
specific.
This patch adds support for the XDomain discovery protocol to the
Thunderbolt bus. We model each remote host connection as a Linux XDomain
device. For each Thunderbolt service found supported on the XDomain
device, we create Linux Thunderbolt service device which Thunderbolt
service drivers can then bind to based on the protocol identification
information retrieved from the property directory describing the
service.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Thunderbolt service might need to find the physical port from a link
the cable is connected to. For instance networking driver uses this
information to generate MAC address according the Apple ThunderboltIP
protocol.
Move this function to thunderbolt.h and rename it to
tb_phy_port_from_link() to reflect the fact that it does not take switch
as parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are needed by Thunderbolt services so move them to thunderbolt.h
to make sure they are available outside of drivers/thunderbolt.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These will be needed by Thunderbolt services when sending and receiving
XDomain control messages. While there change TB_CFG_PKG_PREPARE_TO_SLEEP
value to be decimal in order to be consistent with other members.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thunderbolt XDomain discovery protocol uses directories which contain
properties and other directories to exchange information about what
capabilities the remote host supports. This also includes identification
information like device ID and name.
This adds support for parsing and formatting these properties and
establishes an API drivers can use in addition to the core Thunderbolt
driver. This API is exposed in a new header: include/linux/thunderbolt.h.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These messages are all 32-bit aligned and they should be packed without
the __packed attribute just fine. It also allows compiler to generate
better code on some architectures.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will be using these when communicating XDomain discovery protocol
over Thunderbolt link but they might be useful for other drivers as
well.
Make them available through byteorder/generic.h.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
