sas_user_scan() did not fully process wildcard channel scans
(SCAN_WILD_CARD) when a transport-specific user_scan() callback was
present. Only channel 0 would be scanned via user_scan(), while the
remaining channels were skipped, potentially missing devices.
user_scan() invokes updated sas_user_scan() for channel 0, and if
successful, iteratively scans remaining channels (1 to
shost->max_channel) via scsi_scan_host_selected(). This ensures complete
wildcard scanning without affecting transport-specific scanning behavior.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20250624061649.17990-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_add_lun() tests the device vendor string of SCSI devices to detect
if a SCSI device is in fact an ATA device, in order to correctly handle
SATL power management. The function scsi_cdl_enable() also requires
knowing if a SCSI device is an ATA device to control the state of the
device CDL feature but this function does that by testing for the
presence of the VPD page 89h (ATA INFORMATION page).
sd_read_write_same() also has a similar test.
Simplify these different methods by adding the is_ata field to struct
scsi_device to remember that a SCSI device is in fact an ATA one based
on the device vendor name test. This field can also allow low level
SCSI host adapter drivers to take special actions for ATA devices
(e.g. to better handle ATA NCQ errors).
With this, simplify scsi_cdl_enable() and sd_read_write_same().
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20250611093421.2901633-1-dlemoal@kernel.org
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
async_scan_lock is designed to protect the scanning_hosts list, but there
is no protection here.
Signed-off-by: Chaohai Chen <wdhh66@163.com>
Link: https://lore.kernel.org/r/20250221030755.219277-1-wdhh66@163.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Filesystems can write to disk from page reclaim with __GFP_FS
set. Marc found a case where scsi_realloc_sdev_budget_map() ends up in
page reclaim with GFP_KERNEL, where it could try to take filesystem
locks again, leading to a deadlock.
WARNING: possible circular locking dependency detected
6.13.0 #1 Not tainted
------------------------------------------------------
kswapd0/70 is trying to acquire lock:
ffff8881025d5d78 (&q->q_usage_counter(io)){++++}-{0:0}, at: blk_mq_submit_bio+0x461/0x6e0
but task is already holding lock:
ffffffff81ef5f40 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x9f/0x760
The full lockdep splat can be found in Marc's report:
https://lkml.org/lkml/2025/1/24/1101
Avoid the potential deadlock by doing the allocation with GFP_NOIO, which
prevents both filesystem and block layer recursion.
Reported-by: Marc Aurèle La France <tsi@tuyoix.net>
Signed-off-by: Rik van Riel <riel@surriel.com>
Link: https://lore.kernel.org/r/20250129104525.0ae8421e@fangorn
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----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=molg
-----END PGP SIGNATURE-----
Merge tag 'block-6.14-20250131' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
- MD pull request via Song:
- Fix a md-cluster regression introduced
- More sysfs race fixes
- Mark anything inside queue freezing as not being able to do IO for
memory allocations
- Fix for a regression introduced in loop in this merge window
- Fix for a regression in queue mapping setups introduced in this merge
window
- Fix for the block dio fops attempting an iov_iter revert upton
getting -EIOCBQUEUED on the read side. This one is going to stable as
well
* tag 'block-6.14-20250131' of git://git.kernel.dk/linux:
block: force noio scope in blk_mq_freeze_queue
block: fix nr_hw_queue update racing with disk addition/removal
block: get rid of request queue ->sysfs_dir_lock
loop: don't clear LO_FLAGS_PARTSCAN on LOOP_SET_STATUS{,64}
md/md-bitmap: Synchronize bitmap_get_stats() with bitmap lifetime
blk-mq: create correct map for fallback case
block: don't revert iter for -EIOCBQUEUED
When block drivers or the core block code perform allocations with a
frozen queue, this could try to recurse into the block device to
reclaim memory and deadlock. Thus all allocations done by a process
that froze a queue need to be done without __GFP_IO and __GFP_FS.
Instead of tying to track all of them down, force a noio scope as
part of freezing the queue.
Note that nvme is a bit of a mess here due to the non-owner freezes,
and they will be addressed separately.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20250131120352.1315351-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add kernel-doc for scsi_add_device() since it is exported. This allows it
to be part of the SCSI driver-api docbook.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20241212205217.597844-5-rdunlap@infradead.org
CC: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
CC: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that all SCSI drivers have been converted from .slave_configure() to
.sdev_configure(), remove support for .slave_configure() from the SCSI
core.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-5-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The only difference between the .sdev_configure() and .slave_configure()
methods is that the former accepts an additional 'limits' argument.
Convert all SCSI drivers that define a .slave_configure() method to
.sdev_configure(). This patch prepares for removing the
.slave_configure() method. No functionality has been changed.
Acked-by: Geoff Levand <geoff@infradead.org> # for ps3rom
Acked-by: Khalid Aziz <khalid@gonehiking.org> # for the BusLogic driver
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-4-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Improve naming consistency with the .sdev_prep() and .sdev_destroy()
methods by renaming .device_configure() into .sdev_configure().
Cc: Christoph Hellwig <hch@lst.de>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-3-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename .slave_alloc() into .sdev_init() and .slave_destroy() into
.sdev_destroy(). The new names make it clear that these are actions on
SCSI devices. Make this change in the SCSI core, SCSI drivers and also
in the ATA drivers. No functionality has been changed.
This patch has been created as follows:
* Change the text "slave_alloc" into "sdev_init" in all source files
except those in drivers/net/ and Documentation/.
* Change the text "slave_destroy" into "sdev_destroy" in all source
files except those in drivers/net/ and Documentation/.
* Rename lpfc_no_slave() into lpfc_no_sdev().
* Manually adjust whitespace where necessary to restore vertical
alignment (dc395x driver and include/linux/libata.h).
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
When calling scsi_alloc_sdev() -> blk_mq_alloc_queue(), we don't pass
the sdev as the queuedata, but rather manually set it afterwards. Just
pass to blk_mq_alloc_queue() to have automatically set.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240524084829.2132555-2-john.g.garry@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (ufs, lpfc, qla2xxx, mpi3mr, libsas).
The major update (which causes a conflict with block, see below) is
Christoph removing the queue limits and their associated block
helpers. The remaining patches are assorted minor fixes and
deprecated function updates plus a bit of constification.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZkOnWyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYe7AP93XRN/
xnccJbSTTUL4FFGobq2CYXv58Na+FM/b/+/kEAD+PNi0LmHDdDTOaFUblMd9l4lj
mpvYLRvJ6ifnHX6WXAg=
=PVnL
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, qla2xxx, mpi3mr, libsas).
The major update (which causes a conflict with block, see below) is
Christoph removing the queue limits and their associated block
helpers.
The remaining patches are assorted minor fixes and deprecated function
updates plus a bit of constification"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
scsi: mpi3mr: Sanitise num_phys
scsi: lpfc: Copyright updates for 14.4.0.2 patches
scsi: lpfc: Update lpfc version to 14.4.0.2
scsi: lpfc: Add support for 32 byte CDBs
scsi: lpfc: Change lpfc_hba hba_flag member into a bitmask
scsi: lpfc: Introduce rrq_list_lock to protect active_rrq_list
scsi: lpfc: Clear deferred RSCN processing flag when driver is unloading
scsi: lpfc: Update logging of protection type for T10 DIF I/O
scsi: lpfc: Change default logging level for unsolicited CT MIB commands
scsi: target: Remove unused list 'device_list'
scsi: iscsi: Remove unused list 'connlist_err'
scsi: ufs: exynos: Add support for Tensor gs101 SoC
scsi: ufs: exynos: Add some pa_dbg_ register offsets into drvdata
scsi: ufs: exynos: Allow max frequencies up to 267Mhz
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_TIMER_TICK_SELECT option
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_UFSPR_SECURE option
scsi: ufs: dt-bindings: exynos: Add gs101 compatible
scsi: qla2xxx: Fix debugfs output for fw_resource_count
scsi: qedf: Ensure the copied buf is NUL terminated
scsi: bfa: Ensure the copied buf is NUL terminated
...
This is a version of ->slave_configure that also takes a queue_limits
structure that the caller applies, and thus allows drivers to reconfigure
the queue using the atomic queue limits API.
In the long run it should also replace ->slave_configure entirely as there
is no need to have two different methods here, and the slave name in
addition to being politically charged also has no basis in the SCSI
standards or the kernel code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240409143748.980206-11-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch scsi_add_lun() to use the atomic queue limits API to update the
max_hw_sectors for devices with quirks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240409143748.980206-10-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Turn __scsi_init_queue() into scsi_init_limits() which initializes
queue_limits structure that can be passed to blk_mq_alloc_queue().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240409143748.980206-5-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop
management") introduced the manage_system_start_stop scsi_device flag to
allow libata to indicate to the SCSI disk driver that nothing should be
done when resuming a disk on system resume. This change turned the
execution of sd_resume() into a no-op for ATA devices on system
resume. While this solved deadlock issues during device resume, this change
also wrongly removed the execution of opal_unlock_from_suspend(). As a
result, devices with TCG OPAL locking enabled remain locked and
inaccessible after a system resume from sleep.
To fix this issue, introduce the SCSI driver resume method and implement it
with the sd_resume() function calling opal_unlock_from_suspend(). The
former sd_resume() function is renamed to sd_resume_common() and modified
to call the new sd_resume() function. For non-ATA devices, this result in
no functional changes.
In order for libata to explicitly execute sd_resume() when a device is
resumed during system restart, the function scsi_resume_device() is
introduced. libata calls this function from the revalidation work executed
on devie resume, a state that is indicated with the new device flag
ATA_DFLAG_RESUMING. Doing so, locked TCG OPAL enabled devices are unlocked
on resume, allowing normal operation.
Fixes: 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop management")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218538
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240319071209.1179257-1-dlemoal@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Only a couple of driver updates this time (lpfc and mpt3sas) plus the
usual assorted minor fixes and updates. The major core update is a
set of patches moving retries out of the drivers and into the core.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZfWpoCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXRgAP9EJN6k
lA+f8he/ckzfJu000zv55uwKeZhI1ytgNnQUGwEAzv7Yetcqra18spuEnHRvxnW9
+lxUGh6revfrO/sc5Ho=
=ONSb
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Only a couple of driver updates this time (lpfc and mpt3sas) plus the
usual assorted minor fixes and updates. The major core update is a set
of patches moving retries out of the drivers and into the core"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (84 commits)
scsi: core: Constify the struct device_type usage
scsi: libfc: replace deprecated strncpy() with memcpy()
scsi: lpfc: Replace deprecated strncpy() with strscpy()
scsi: bfa: Fix function pointer type mismatch for state machines
scsi: bfa: Fix function pointer type mismatch for hcb_qe->cbfn
scsi: bfa: Remove additional unnecessary struct declarations
scsi: csiostor: Avoid function pointer casts
scsi: qla1280: Remove redundant assignment to variable 'mr'
scsi: core: Make scsi_bus_type const
scsi: core: Really include kunit tests with SCSI_LIB_KUNIT_TEST
scsi: target: tcm_loop: Make tcm_loop_lld_bus const
scsi: scsi_debug: Make pseudo_lld_bus const
scsi: iscsi: Make iscsi_flashnode_bus const
scsi: fcoe: Make fcoe_bus_type const
scsi: lpfc: Copyright updates for 14.4.0.0 patches
scsi: lpfc: Update lpfc version to 14.4.0.0
scsi: lpfc: Change lpfc_vport load_flag member into a bitmask
scsi: lpfc: Change lpfc_vport fc_flag member into a bitmask
scsi: lpfc: Protect vport fc_nodes list with an explicit spin lock
scsi: lpfc: Change nlp state statistic counters into atomic_t
...
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the
scsi_host_type, scsi_target_type and scsi_dev_type variables to be constant
structures as well, placing it into read-only memory which can not be
modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240219-device_cleanup-scsi-v1-1-c5edf2afe178@marliere.net
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pass a queue_limits to blk_mq_init_queue and apply it if non-NULL. This
will allow allocating queues with valid queue limits instead of setting
the values one at a time later.
Also rename the function to blk_mq_alloc_queue as that is a much better
name for a function that allocates a queue and always pass the queuedata
argument instead of having a separate version for the extra argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240213073425.1621680-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This has scsi_report_lun_scan() have the SCSI midlayer retry errors instead
of driving them itself.
There is one behavior change where we no longer retry when
scsi_execute_cmd() returns < 0, but we should be ok. We don't need to retry
for failures like the queue being removed, and for the case where there are
no tags/reqs the block layer waits/retries for us. For possible memory
allocation failures from blk_rq_map_kern() we use GFP_NOIO, so retrying
will probably not help.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20240123002220.129141-14-michael.christie@oracle.com
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Description from: Martin Wilck <mwilck@suse.com>:
The SCSI mid layer doesn't retry commands after DID_TIME_OUT (see
scsi_noretry_cmd()). Packet loss in the fabric can cause spurious timeouts
during SCSI device probing, causing device probing to fail. This has been
observed in FCoE uplink failover tests, for example.
This patch fixes the issue by retrying the INQUIRY.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20240123002220.129141-4-michael.christie@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This has scsi_probe_lun() ask the SCSI midlayer to retry UAs instead of
driving them itself.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20240123002220.129141-3-michael.christie@oracle.com
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit ff48b37802 ("scsi: Do not attempt to rescan suspended devices")
modified scsi_rescan_device() to avoid attempting rescanning a suspended
device. However, the modification added a check to verify that a SCSI
device is in the running state without checking if the device request
queue (in the case of block device) is also running, thus allowing the
exectuion of internal requests. Without checking the device request
queue, commit ff48b37802 fix is incomplete and deadlocks on resume can
still happen. Use blk_queue_pm_only() to check if the device request
queue allows executing commands in addition to checking the SCSI device
state.
Reported-by: Petr Tesarik <petr@tesarici.cz>
Fixes: ff48b37802 ("scsi: Do not attempt to rescan suspended devices")
Cc: stable@vger.kernel.org
Tested-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
A larger than usual set of fixes for 6.6-rc4 due to the unexpected
number of fixes needed to address ATA disks suspend/resume issues.
In more details:
- Add missing additionalProperties on child nodes to the pata-common DT
bindings (Rob).
- Fix handling of the REPORT SUPPORTED OPERATION CODES command to
ignore reserved bits (Niklas).
- Increase port multiplier soft reset timeout to accomodate slow
devices and avoid issues on wakeup (Matthias).
- A couple of minor code fixes to avoid compilation warnings in
libata-core and libata-eh (me).
- Many patches from me to address suspend/resume issues, and in
particular a potential deadlock on resume due to the SCSI disk driver
resume operation not being synchronized with libata EH port resume
handling. This is addressed by changing the scsi disk driver disk
start/stop control to allow libata to execute disk suspend (spin
down) and resume (spin up) on its own during system suspend/resume.
Runtime suspend/resume control remains with the SCSI disk driver.
Other fixes include:
- Fix libata power management request issuing to avoid races.
- Establish a link between ATA ports and SCSI devices to order PM
operations.
- Fix device removal to avoid issues with driver rmmod removal.
- Fix synchronization of libata device rescan and SCSI disk resume
operation.
- Remove libsas PM operations as suspend/resume is handled directly
by the sas controller resume.
- Fix the SCSI disk driver to not issue commands to suspended disks,
thus avoiding potential system lock-up on resume.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCZRbR0gAKCRDdoc3SxdoY
dkArAP9PFTRgsXEwfE7arBXCwQqXj/W0R2KgKug7Fno+SoQLnAD/ZKe2TR50uwxr
9mwYROdMgi50T9ax1RX1jWA0npGXmQg=
=cFzG
-----END PGP SIGNATURE-----
Merge tag 'ata-6.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA fixes from Damien Le Moal:
"A larger than usual set of fixes for 6.6-rc4 due to the unexpected
number of fixes needed to address ATA disks suspend/resume issues.
In more detail:
- Add missing additionalProperties on child nodes to the pata-common
DT bindings (Rob)
- Fix handling of the REPORT SUPPORTED OPERATION CODES command to
ignore reserved bits (Niklas)
- Increase port multiplier soft reset timeout to accomodate slow
devices and avoid issues on wakeup (Matthias)
- A couple of minor code fixes to avoid compilation warnings in
libata-core and libata-eh (me)
- Many patches from me to address suspend/resume issues, and in
particular a potential deadlock on resume due to the SCSI disk
driver resume operation not being synchronized with libata EH port
resume handling.
This is addressed by changing the scsi disk driver disk start/stop
control to allow libata to execute disk suspend (spin down) and
resume (spin up) on its own during system suspend/resume. Runtime
suspend/resume control remains with the SCSI disk driver.
Other fixes include:
- Fix libata power management request issuing to avoid races
- Establish a link between ATA ports and SCSI devices to order PM
operations
- Fix device removal to avoid issues with driver rmmod removal
- Fix synchronization of libata device rescan and SCSI disk resume
operation
- Remove libsas PM operations as suspend/resume is handled
directly by the sas controller resume
- Fix the SCSI disk driver to not issue commands to suspended
disks, thus avoiding potential system lock-up on resume"
* tag 'ata-6.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-eh: Fix compilation warning in ata_eh_link_report()
ata: libata-core: Fix compilation warning in ata_dev_config_ncq()
scsi: sd: Do not issue commands to suspended disks on shutdown
ata: libata-core: Do not register PM operations for SAS ports
ata: libata-scsi: Fix delayed scsi_rescan_device() execution
scsi: Do not attempt to rescan suspended devices
ata: libata-scsi: Disable scsi device manage_system_start_stop
scsi: sd: Differentiate system and runtime start/stop management
ata: libata-scsi: link ata port and scsi device
ata: libata-core: Fix port and device removal
ata: libata-core: Fix ata_port_request_pm() locking
ata: libata-sata: increase PMP SRST timeout to 10s
ata: libata-scsi: ignore reserved bits for REPORT SUPPORTED OPERATION CODES
dt-bindings: ata: pata-common: Add missing additionalProperties on child nodes
scsi_rescan_device() takes a scsi device lock before executing a device
handler and device driver rescan methods. Waiting for the completion of
any command issued to the device by these methods will thus be done with
the device lock held. As a result, there is a risk of deadlocking within
the power management code if scsi_rescan_device() is called to handle a
device resume with the associated scsi device not yet resumed.
Avoid such situation by checking that the target scsi device is in the
running state, that is, fully capable of executing commands, before
proceeding with the rescan and bailout returning -EWOULDBLOCK otherwise.
With this error return, the caller can retry rescaning the device after
a delay.
The state check is done with the device lock held and is thus safe
against incoming suspend power management operations.
Fixes: 6aa0365a3c ("ata: libata-scsi: Avoid deadlock on rescan after device resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Some old drives (e.g. an Ultra320 SCSI disk as reported by John) do not
seem to execute MAINTENANCE_IN / MI_REPORT_SUPPORTED_OPERATION_CODES
commands correctly and hang when a non-zero service action is specified
(one command format with service action case in scsi_report_opcode()).
Currently, CDL probing with scsi_cdl_check_cmd() is the only caller using a
non zero service action for scsi_report_opcode(). To avoid issues with
these old drives, do not attempt CDL probe if the device reports support
for an SPC version lower than 5 (CDL was introduced in SPC-5). To keep
things working with ATA devices which probe for the CDL T2A and T2B pages
introduced with SPC-6, modify ata_scsiop_inq_std() to claim SPC-6 version
compatibility for ATA drives supporting CDL.
SPC-6 standard version number is defined as Dh (= 13) in SPC-6 r09. Fix
scsi_probe_lun() to correctly capture this value by changing the bit mask
for the second byte of the INQUIRY response from 0x7 to 0xf.
include/scsi/scsi.h is modified to add the definition SCSI_SPC_6 with the
value 14 (Dh + 1). The missing definitions for the SCSI_SPC_4 and
SCSI_SPC_5 versions are also added.
Reported-by: John David Anglin <dave.anglin@bell.net>
Fixes: 624885209f ("scsi: core: Detect support for command duration limits")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230915022034.678121-1-dlemoal@kernel.org
Tested-by: David Gow <david@davidgow.net>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most callers of scsi_rescan_device() have the scsi_device pointer readily
available. Pass a struct scsi_device pointer to scsi_rescan_device()
instead of a struct device pointer. This change prevents that a pointer to
another struct device would be passed accidentally to scsi_rescan_device().
Remove the scsi_rescan_device() declaration from the scsi_priv.h header
file since it duplicates the declaration in <scsi/scsi_host.h>.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230822153043.4046244-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce the function scsi_cdl_check() to detect if a device supports
command duration limits (CDL). Support for the READ 16, WRITE 16, READ 32
and WRITE 32 commands are checked using the function scsi_report_opcode()
to probe the rwcdlp and cdlp bits as they indicate the mode page defining
the command duration limits descriptors that apply to the command being
tested.
If any of these commands support CDL, the field cdl_supported of struct
scsi_device is set to 1 to indicate that the device supports CDL.
Support for CDL for a device is advertizes through sysfs using the new
cdl_supported device attribute. This attribute value is 1 for a device
supporting CDL and 0 otherwise.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Co-developed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-9-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some storage, such as AIX VDASD (virtual storage) and IBM 2076 (front
end), fail as a result of commit c92a6b5d63 ("scsi: core: Query VPD
size before getting full page").
That commit changed getting SCSI VPD pages so that we now read just
enough of the page to get the actual page size, then read the whole
page in a second read. The problem is that the above mentioned
hardware returns zero for the page size, because of a firmware
error. In such cases, until the firmware is fixed, this new blacklist
flag says to revert to the original method of reading the VPD pages,
i.e. try to read a whole buffer's worth on the first try.
[mkp: reworked somewhat]
Fixes: c92a6b5d63 ("scsi: core: Query VPD size before getting full page")
Reported-by: Martin Wilck <mwilck@suse.com>
Suggested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Lee Duncan <lduncan@suse.com>
Link: https://lore.kernel.org/r/20220928181350.9948-1-leeman.duncan@gmail.com
Tested-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (ufs, lpfc, qla2xxx, libsas). The major
core change is a rework to remove the two helpers around
scsi_execute_cmd and use it as the only submission interface along
with other minor fixes and updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCY/Z7BSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfF9AP9HzZaZ
0XumuxjchcJHRntcIAzb9kE62SSWFxBrgZQCtAEAyhAO1zK284esgCa+arkzEC7p
uhxpufQSGnYvbasStsU=
=VsH1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, qla2xxx, libsas).
The major core change is a rework to remove the two helpers around
scsi_execute_cmd and use it as the only submission interface along
with other minor fixes and updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (142 commits)
scsi: ufs: core: Fix an error handling path in ufshcd_read_desc_param()
scsi: ufs: core: Fix device management cmd timeout flow
scsi: aic94xx: Add missing check for dma_map_single()
scsi: smartpqi: Replace one-element array with flexible-array member
scsi: mpt3sas: Fix a memory leak
scsi: qla2xxx: Remove the unused variable wwn
scsi: ufs: core: Fix kernel-doc syntax
scsi: ufs: core: Add hibernation callbacks
scsi: snic: Fix memory leak with using debugfs_lookup()
scsi: ufs: core: Limit DMA alignment check
scsi: Documentation: Correct spelling
scsi: Documentation: Correct spelling
scsi: target: Documentation: Correct spelling
scsi: aacraid: Allocate cmd_priv with scsicmd
scsi: ufs: qcom: dt-bindings: Add SM8550 compatible string
scsi: ufs: ufs-qcom: Clear qunipro_g4_sel for HW version major 5
scsi: ufs: qcom: fix platform_msi_domain_free_irqs() reference
scsi: ufs: core: Enable DMA clustering
scsi: ufs: exynos: Fix the maximum segment size
scsi: ufs: exynos: Fix DMA alignment for PAGE_SIZE != 4096
...
This reverts commit 948e922fc4.
Not all targets that return PQ=1 and PDT=0 should be ignored. While
the SCSI spec is vague in this department, there appears to be a
critical mass of devices which rely on devices being accessible with
this combination of reported values.
Fixes: 948e922fc4 ("scsi: core: map PQ=1, PDT=other values to SCSI_SCAN_TARGET_PRESENT")
Link: https://lore.kernel.org/r/yq1lelrleqr.fsf@ca-mkp.ca.oracle.com
Acked-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Martin Wilck <mwilck@suse.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_execute_req() is going to be removed. Convert SCSI midlayer to
scsi_execute_cmd().
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (target, ufs, smartpqi, lpfc). There are
some core changes, mostly around reworking some of our user context
assumptions in device put and moving some code around. The remaining
updates are bug fixes and minor changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCY5jjrSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishR9iAPwN++uF
BNlCD36duS8LslKQMPAmFxWt3d/4RWAHsXj2WQEAtu9q8K9PSe1ueb4y+rAEG4oj
2AUQhR3v9ciWBBKlDog=
=JYJC
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (target, ufs, smartpqi, lpfc).
There are some core changes, mostly around reworking some of our user
context assumptions in device put and moving some code around.
The remaining updates are bug fixes and minor changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (138 commits)
scsi: sg: Fix get_user() in call sg_scsi_ioctl()
scsi: megaraid_sas: Fix some spelling mistakes in comment
scsi: core: Use SCSI_SCAN_INITIAL in do_scsi_scan_host()
scsi: core: Use SCSI_SCAN_RESCAN in __scsi_add_device()
scsi: ufs: ufs-mediatek: Remove unnecessary return code
scsi: ufs: core: Fix the polling implementation
scsi: libsas: Do not export sas_ata_wait_after_reset()
scsi: hisi_sas: Fix SATA devices missing issue during I_T nexus reset
scsi: libsas: Add smp_ata_check_ready_type()
scsi: Revert "scsi: hisi_sas: Don't send bcast events from HW during nexus HA reset"
scsi: Revert "scsi: hisi_sas: Drain bcast events in hisi_sas_rescan_topology()"
scsi: ufs: ufs-mediatek: Modify the return value
scsi: ufs: ufs-mediatek: Remove unneeded code
scsi: device_handler: alua: Call scsi_device_put() from non-atomic context
scsi: device_handler: alua: Revert "Move a scsi_device_put() call out of alua_check_vpd()"
scsi: snic: Fix possible UAF in snic_tgt_create()
scsi: qla2xxx: Initialize vha->unknown_atio_[list, work] for NPIV hosts
scsi: qla2xxx: Remove duplicate of vha->iocb_work initialization
scsi: fcoe: Fix transport not deattached when fcoe_if_init() fails
scsi: sd: Use 16-byte SYNCHRONIZE CACHE on ZBC devices
...
Instead of using hardcoded '0' as the do_scsi_scan_host() ->
scsi_scan_host_selected() rescan arg, use proper macro SCSI_SCAN_INITIAL.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20221121121725.1910795-3-john.g.garry@oracle.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of using hardcoded '1' as the __scsi_add_device() ->
scsi_probe_and_add_lun() rescan arg, use proper macro SCSI_SCAN_RESCAN.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20221121121725.1910795-2-john.g.garry@oracle.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that blk_mq_destroy_queue does not release the queue reference, there
is no need for a second queue reference to be held by the scsi_device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20221018135720.670094-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are two .exit_cmd_priv implementations. Both implementations use
resources associated with the SCSI host. Make sure that these resources are
still available when .exit_cmd_priv is called by waiting inside
scsi_remove_host() until the tag set has been freed.
This commit fixes the following use-after-free:
==================================================================
BUG: KASAN: use-after-free in srp_exit_cmd_priv+0x27/0xd0 [ib_srp]
Read of size 8 at addr ffff888100337000 by task multipathd/16727
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
print_report.cold+0x5e/0x5db
kasan_report+0xab/0x120
srp_exit_cmd_priv+0x27/0xd0 [ib_srp]
scsi_mq_exit_request+0x4d/0x70
blk_mq_free_rqs+0x143/0x410
__blk_mq_free_map_and_rqs+0x6e/0x100
blk_mq_free_tag_set+0x2b/0x160
scsi_host_dev_release+0xf3/0x1a0
device_release+0x54/0xe0
kobject_put+0xa5/0x120
device_release+0x54/0xe0
kobject_put+0xa5/0x120
scsi_device_dev_release_usercontext+0x4c1/0x4e0
execute_in_process_context+0x23/0x90
device_release+0x54/0xe0
kobject_put+0xa5/0x120
scsi_disk_release+0x3f/0x50
device_release+0x54/0xe0
kobject_put+0xa5/0x120
disk_release+0x17f/0x1b0
device_release+0x54/0xe0
kobject_put+0xa5/0x120
dm_put_table_device+0xa3/0x160 [dm_mod]
dm_put_device+0xd0/0x140 [dm_mod]
free_priority_group+0xd8/0x110 [dm_multipath]
free_multipath+0x94/0xe0 [dm_multipath]
dm_table_destroy+0xa2/0x1e0 [dm_mod]
__dm_destroy+0x196/0x350 [dm_mod]
dev_remove+0x10c/0x160 [dm_mod]
ctl_ioctl+0x2c2/0x590 [dm_mod]
dm_ctl_ioctl+0x5/0x10 [dm_mod]
__x64_sys_ioctl+0xb4/0xf0
dm_ctl_ioctl+0x5/0x10 [dm_mod]
__x64_sys_ioctl+0xb4/0xf0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Link: https://lore.kernel.org/r/20220826002635.919423-1-bvanassche@acm.org
Fixes: 65ca846a53 ("scsi: core: Introduce {init,exit}_cmd_priv()")
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: John Garry <john.garry@huawei.com>
Cc: Li Zhijian <lizhijian@fujitsu.com>
Reported-by: Li Zhijian <lizhijian@fujitsu.com>
Tested-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revert the patch series "Call blk_mq_free_tag_set() earlier" because it
introduces a deadlock if the scsi_remove_host() caller holds a reference on
a device, target or host.
Link: https://lore.kernel.org/r/20220821220502.13685-5-bvanassche@acm.org
Fixes: fe44260419 ("scsi: core: Make sure that targets outlive devices")
Reported-by: syzbot+bafeb834708b1bb750bc@syzkaller.appspotmail.com
Tested-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revert the patch series "Call blk_mq_free_tag_set() earlier" because it
introduces a deadlock if the scsi_remove_host() caller holds a reference on
a device, target or host.
Link: https://lore.kernel.org/r/20220821220502.13685-4-bvanassche@acm.org
Fixes: 16728aaba6 ("scsi: core: Make sure that hosts outlive targets")
Reported-by: syzbot+bafeb834708b1bb750bc@syzkaller.appspotmail.com
Tested-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the race conditions between SCSI LLD kernel module unloading and SCSI
device and target removal by making sure that SCSI hosts are destroyed
after all associated target and device objects have been freed.
Link: https://lore.kernel.org/r/20220728221851.1822295-3-bvanassche@acm.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: John Garry <john.garry@huawei.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[ bvanassche: Reworked Ming's patch and split it ]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This commit prevents that the following sequence triggers a kernel crash:
- Deletion of a SCSI device is requested via sysfs. Device removal takes
some time because blk_cleanup_queue() is waiting for the SCSI error
handler.
- The SCSI target associated with that SCSI device is removed.
- scsi_remove_target() returns and its caller frees the resources
associated with the SCSI target.
- The error handler makes progress and invokes an LLD callback that
dereferences the SCSI target pointer.
Link: https://lore.kernel.org/r/20220728221851.1822295-2-bvanassche@acm.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: John Garry <john.garry@huawei.com>
Cc: Li Zhijian <lizhijian@fujitsu.com>
Reported-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Low-level device drivers have had the ability to limit the size of an
INQUIRY for many years. This made sense for a wide variety of legacy
devices. However, we are unnecessarily truncating the INQUIRY response for
many modern devices. This prevents us from consulting fields beyond the
first 36 bytes.
If a device reports that it supports a larger INQUIRY response, and the
device also reports that it implements SPC-4 or newer, allow the larger
INQUIRY to proceed.
Link: https://lore.kernel.org/r/20220302053559.32147-4-martin.petersen@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit edb854a368 ("scsi: core: Reallocate device's budget map on
queue depth change"), the sbitmap for the device budget map may be
reallocated after the slave device depth is configured.
When the sbitmap is reallocated we use the result from
scsi_device_max_queue_depth() for the sbitmap size, but don't resize to
match the actual device queue depth.
Fix by resizing the sbitmap after reallocating the budget sbitmap. We do
this instead of init'ing the sbitmap to the device queue depth as the user
may want to change the queue depth later via sysfs or other.
Link: https://lore.kernel.org/r/1647423870-143867-1-git-send-email-john.garry@huawei.com
Fixes: edb854a368 ("scsi: core: Reallocate device's budget map on queue depth change")
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We currently use ->cmd_per_lun as initial queue depth for setting up the
budget_map. Martin Wilck reported that it is common for the queue_depth to
be subsequently updated in slave_configure() based on detected hardware
characteristics.
As a result, for some drivers, the static host template settings for
cmd_per_lun and can_queue won't actually get used in practice. And if the
default values are used to allocate the budget_map, memory may be consumed
unnecessarily.
Fix the issue by reallocating the budget_map after ->slave_configure()
returns. At that time the device queue_depth should accurately reflect what
the hardware needs.
Link: https://lore.kernel.org/r/20220127153733.409132-1-ming.lei@redhat.com
Cc: Bart Van Assche <bvanassche@acm.org>
Reported-by: Martin Wilck <martin.wilck@suse.com>
Suggested-by: Martin Wilck <martin.wilck@suse.com>
Tested-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'scsi_scan_type' is only used in one source file. Hence declare it static.
Link: https://lore.kernel.org/r/20211129194609.3466071-3-bvanassche@acm.org
Fixes: a19a93e4c6 ("scsi: core: pm: Rely on the device driver core for async power management")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Suppress the following kernel-doc warning:
drivers/scsi/scsi_scan.c:129: warning: Function parameter or member 'dev' not described in 'scsi_enable_async_suspend'
Link: https://lore.kernel.org/r/20211129194609.3466071-2-bvanassche@acm.org
Fixes: a19a93e4c6 ("scsi: core: pm: Rely on the device driver core for async power management")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, smartpqi, lpfc,
target, megaraid_sas, hisi_sas, qla2xxx) and minor updates and bug
fixes. Notable core changes are the removal of scsi->tag which caused
some churn in obsolete drivers and a sweep through all drivers to call
scsi_done() directly instead of scsi->done() which removes a pointer
indirection from the hot path and a move to register core sysfs files
earlier, which means they're available to KOBJ_ADD processing, which
necessitates switching all drivers to using attribute groups.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYYUfBCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbUJAQDZt4oc
vUx9JpyrdHxxTCuOzVFd8W1oJn0k5ltCBuz4yAD8DNbGhGm93raMSJ3FOOlzLEbP
RG8vBdpxMudlvxAPi/A=
=BSFz
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, smartpqi, lpfc,
target, megaraid_sas, hisi_sas, qla2xxx) and minor updates and bug
fixes.
Notable core changes are the removal of scsi->tag which caused some
churn in obsolete drivers and a sweep through all drivers to call
scsi_done() directly instead of scsi->done() which removes a pointer
indirection from the hot path and a move to register core sysfs files
earlier, which means they're available to KOBJ_ADD processing, which
necessitates switching all drivers to using attribute groups"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: lpfc: Update lpfc version to 14.0.0.3
scsi: lpfc: Allow fabric node recovery if recovery is in progress before devloss
scsi: lpfc: Fix link down processing to address NULL pointer dereference
scsi: lpfc: Allow PLOGI retry if previous PLOGI was aborted
scsi: lpfc: Fix use-after-free in lpfc_unreg_rpi() routine
scsi: lpfc: Correct sysfs reporting of loop support after SFP status change
scsi: lpfc: Wait for successful restart of SLI3 adapter during host sg_reset
scsi: lpfc: Revert LOG_TRACE_EVENT back to LOG_INIT prior to driver_resource_setup()
scsi: ufs: ufshcd-pltfrm: Fix memory leak due to probe defer
scsi: ufs: mediatek: Avoid sched_clock() misuse
scsi: mpt3sas: Make mpt3sas_dev_attrs static
scsi: scsi_transport_sas: Add 22.5 Gbps link rate definitions
scsi: target: core: Stop using bdevname()
scsi: aha1542: Use memcpy_{from,to}_bvec()
scsi: sr: Add error handling support for add_disk()
scsi: sd: Add error handling support for add_disk()
scsi: target: Perform ALUA group changes in one step
scsi: target: Replace lun_tg_pt_gp_lock with rcu in I/O path
scsi: target: Fix alua_tg_pt_gps_count tracking
scsi: target: Fix ordered tag handling
...
Export scsi_device_from_queue for use with pktcdvd and use that instead
of the otherwise unused QUEUE_FLAG_SCSI_PASSTHROUGH queue flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20211021060607.264371-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
