Implement graceful handling of surprise or orderly removal of PCIe HBA:
- Detect a hot removal of the controller at certain critical places in the
driver. Early detection will help to reduce the time taken for cleaning
up the hot-removed controller at the driver level.
- Poll the status of the port enable issued after reset once every 5
seconds to avoid a long delay in detecting unavailable controller.
Link: https://lore.kernel.org/r/20220912135742.11764-5-sreekanth.reddy@broadcom.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch to the new generic PCI power management framework. Also, remove
unnecessary calls to the PCI helper functions (such as
pci_set_power_state(), pci_enable_wake(), pci_save_state(),
pci_restore_state() etc).
Link: https://lore.kernel.org/r/20220912135742.11764-3-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Block the I/Os on the target devices until corresponding target device's
target dev objects are refreshed as part of post controller reset
operation.
Link: https://lore.kernel.org/r/20220804131226.16653-16-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the host's SAS ports if there is change in port id or phys. If the
port id is changed, then the driver updates it. If some phys are
enabled/disabled during reset, then driver updates them in STL.
Check for the responding expander devices and update the device handle if
it got changed. Register the expander with STL if it got added during reset
and unregister the expander device if it got removed during reset.
[mkp: include fix for zeroday warning]
Link: https://lore.kernel.org/r/20220804131226.16653-15-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for the following SAS transport class callbacks:
- get_linkerrors
- get_enclosure_identifier
- get_bay_identifier
- phy_reset
- phy_enable
- set_phy_speed
- smp_handler
Link: https://lore.kernel.org/r/20220804131226.16653-14-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add framework to issue MPT transport commands to controllers. Also issue
the MPT transport commands to get the manufacturing info of SAS expander
device.
Link: https://lore.kernel.org/r/20220804131226.16653-13-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Register/unregister the SAS, SATA devices to SCSI Transport Layer(STL)
whenever the corresponding device is added/removed from topology.
Link: https://lore.kernel.org/r/20220804131226.16653-12-sreekanth.reddy@broadcom.com
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When device is registered with the STL then get the corresponding device's
target object using the rphy in below callback functions:
- mpi3mr_target_alloc()
- mpi3mr_slave_alloc()
- mpi3mr_slave_configure()
- mpi3mr_slave_destroy()
Link: https://lore.kernel.org/r/20220804131226.16653-11-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Register/unregister the expander devices to SCSI Transport Layer(STL)
whenever the corresponding expander is added/removed from topology.
Link: https://lore.kernel.org/r/20220804131226.16653-10-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Register the SAS, SATA devices to SCSI Transport Layer (STL) only if
multipath capability is disabled in the controller's firmware.
Link: https://lore.kernel.org/r/20220804131226.16653-9-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the following helper functions:
- Update the host phys with STL
- Remove the device's SAS port with STL
Link: https://lore.kernel.org/r/20220804131226.16653-8-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the following helper functions:
- Get the device's sas address by reading corresponding device's Device
page0
- Get the expander object from expander list based on expander's handle
- Get the target device object from target device list based on device's
sas address
- Get the expander device object from expander list based on expanders's
sas address
- Get hba port object from hba port table list based on port's port id
Link: https://lore.kernel.org/r/20220804131226.16653-7-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable and process the Enclosure device add event.
Link: https://lore.kernel.org/r/20220804131226.16653-5-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since blk_mq_map_queues() and the .map_queues() callbacks always return 0,
change their return type into void. Most callers ignore the returned value
anyway.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Acked-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://lore.kernel.org/r/20220815170043.19489-3-bvanassche@acm.org
[axboe: fold in fix from Bart]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Updates to the usual drivers (ufs, qla2xx, target, lpfc, smartpqi,
mpi3mr). The main driver change that might cause issues on down the
road is the conversion of some of our oldest surviving drivers to the
DMA API (should only affect m68k). The only major core change is the
rework of async resume; the rest are either completely trivial or for
updating deprecated APIs.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYuvakyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfvOAP4m0N6b
e3JwoBtB1c0JMKv6G4gka8suEG8p5f4khDu8wwD+LfGUCzG49Y5Ts7rByXfEiGgO
krSdwsAZiV6yKg/HuPw=
=Ak9L
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, qla2xx, target, lpfc, smartpqi,
mpi3mr).
The main driver change that might cause issues on down the road is the
conversion of some of our oldest surviving drivers to the DMA API
(should only affect m68k).
The only major core change is the rework of async resume; the rest are
either completely trivial or for updating deprecated APIs"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (195 commits)
scsi: target: Remove XDWRITEREAD emulated support
scsi: megaraid: Remove the static variable initialisation
scsi: ch: Do not initialise statics to 0
scsi: ufs: core: Fix spelling mistake "Cannnot" -> "Cannot"
scsi: target: iscsi: Do not require target authentication
scsi: target: iscsi: Allow AuthMethod=None
scsi: target: iscsi: Support base64 in CHAP
scsi: target: iscsi: Add support for extended CDB AHS
scsi: ufs: dt-bindings: Add SC8280XP binding
scsi: target: iscsi: Fix clang -Wformat warnings
scsi: ufs: core: Read device property for ref clock
scsi: libsas: Resume SAS host for phy reset or enable via sysfs
scsi: hisi_sas: Modify v3 HW SATA completion error processing
scsi: hisi_sas: Relocate DMA unmap of SMP task
scsi: hisi_sas: Remove unnecessary variable to hold DMA map elements
scsi: hisi_sas: Call hisi_sas_slave_configure() from slave_configure_v3_hw()
scsi: mpi3mr: Delete a stray tab
scsi: mpi3mr: Unlock on error path
scsi: mpi3mr: Reduce VD queue depth on detecting throttling
scsi: mpi3mr: Resource Based Metering
...
This code is indented one more tab than it should be.
Link: https://lore.kernel.org/r/YtVCFshEJNC7ELid@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce the VD queue depth on detecting the throttling condition.
[mkp: incorporate fix for pointer cast issue reported by the test
robot and Guenter Roeck]
Link: https://lore.kernel.org/r/20220708195020.8323-3-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update driver to track cumulative pending large data size at the controller
level and at the throttle group level. When one of the values meet or
exceed the controller's firmware-determined high threshold value, then the
driver will divert future selective I/O to the firmware. Once both
controller level and at the throttle group level cumulative pending large
data size reach controller's firmware determined low threshold value, then
the driver will stop diverting I/Os to the firmware.
Link: https://lore.kernel.org/r/20220708195020.8323-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable shared host tagset to make sure that total outstanding I/O count can
not exceed controller's can_queue setting.
Link: https://lore.kernel.org/r/20220628074848.5036-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We no longer use the 'reserved' arg in busy_tag_iter_fn for any iter
function so it may be dropped.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me> #nvme
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/1657109034-206040-6-git-send-email-john.garry@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add sysfs attributes for exposing target device details such as SAS
address, firmware device handle, and persistent ID for the
controller-attached devices and RAID volumes.
Link: https://lore.kernel.org/r/20220517115310.13062-3-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Complete all new I/O requests issued to an unrecoverable controller with
DID_ERROR status instead of returning the I/O requests with
SCSI_MLQUEUE_HOST_BUSY. This will prevent the infinite retries of the new
I/Os when a controller is in an unrecoverable state.
Link: https://lore.kernel.org/r/20220505184808.24049-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If any drive is missing during reset, the driver checks whether the device
is exposed to the OS. If it is, then it removes the device from the OS and
its own internal list. For hidden devices, even if they are found as
missing during reset, the driver is not removing them from its internal
list.
Modify driver to remove hidden devices from the driver's target device list
if they are missing during soft reset.
Link: https://lore.kernel.org/r/20220505184808.24049-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement driver support for management applications to enable persistent
event log (PEL) notifications. Upon receipt of events, the driver will
increment a sysfs variable named event_counter. The management application
will poll for event_counter value changes and signal the application about
events.
Link: https://lore.kernel.org/r/20220429211641.642010-6-sumit.saxena@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are certain management commands which require firmware intervention.
These commands are termed MPT commands. Add support for them.
Link: https://lore.kernel.org/r/20220429211641.642010-5-sumit.saxena@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are certain bsg commands which need to be completed by the driver
without involving firmware. These requests are termed driver commands. Add
support for these.
Link: https://lore.kernel.org/r/20220429211641.642010-3-sumit.saxena@broadcom.com
Reported by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create bsg device per controller for controller management purposes.
bsg device nodes will be named /dev/bsg/mpi3mrctl0, /dev/bsg/mpi3mrctl1,
etc.
Link: https://lore.kernel.org/r/20220429211641.642010-2-sumit.saxena@broadcom.com
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following warning by not allocating driver's event handling worker
queue with WQ_MEM_RECLAIM flag enabled:
workqueue: WQ_MEM_RECLAIM
mpi3mr_fwevt_worker [mpi3mr] is flushing !WQ_MEM_RECLAIM events
Link: https://lore.kernel.org/r/20220218180515.27455-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is missing to set the residual size while completing an
I/O. Ensure proper data transfer size is reported to the kernel on I/O
completion based on the transfer length reported by the firmware.
Link: https://lore.kernel.org/r/20220210095817.22828-7-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a driver command which requires the driver to issue a follow up
command using the same command frame is outstanding and a soft reset
operation occurs, then that driver command frame is getting marked as in
use permanently and won't be reused again.
Clear the driver command frames while flushing out the outstanding commands
and avoid issuing any new requests using these command frames while soft
reset is going on.
Link: https://lore.kernel.org/r/20220210095817.22828-6-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hibernation operation fails when it is issued for second time. This is
because the driver is trying to release the IOC's PCI resources after
setting power state to D3.
Set the IOC's power state to D3 only after releasing the IOC's PCI
resources.
Link: https://lore.kernel.org/r/20220210095817.22828-5-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During controller reset, the driver tries to flush all the pending firmware
event works from worker queue that are queued prior to the reset. However,
if any work is waiting for device addition/removal operation to be
completed at the SML, then a deadlock is observed. This is due to the
controller reset waiting for the device addition/removal to be completed
and the device/addition removal is waiting for the controller reset to be
completed.
To limit this deadlock, continue with the controller reset handling without
canceling the work which is waiting for device addition/removal operation
to complete at SML.
Link: https://lore.kernel.org/r/20220210095817.22828-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enhance driver to consider MPI3_IOCSTATUS_SCSI_IOC_TERMINATED as a success
for TMs issued by it and check the pending I/Os to decide the success or
failure of the task management requests instead of just considering the
MPI3_IOCSTATUS_SCSI_IOC_TERMINATED as a failure of the task management
request.
Link: https://lore.kernel.org/r/20211220141159.16117-24-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for the io_uring interface in I/O-polled mode.
This feature is disabled in the driver by default. To enable the feature, a
module parameter "poll_queues" has to be set with the desired number of
polling queues.
When the feature is enabled, the driver reserves a certain number of
operational queue pairs for the poll_queues either from the available queue
pairs or creates additional queue pairs based on the operational queue
availability.
The Polling queues will have corresponding IRQ and ISR functions as similar
to default queues. However, the IRQ line is disabled by the driver for
poll_queues.
Link: https://lore.kernel.org/r/20211220141159.16117-22-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print cable management & temperature threshold event data.
Use vendor id & device id macro definitions from MPI3 headers.
Link: https://lore.kernel.org/r/20211220141159.16117-21-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The IOC sends a Prepare for Reset Event to the host to prepare for a Soft
Reset. This event data has two reason codes:
1. Start - The host is expected to gracefully quiesce all I/O within
approximately 1 second.
2. Abort - The IOC is requesting to abort a previous Prepare for Reset
Event request. Normal I/O may be resumed.
Link: https://lore.kernel.org/r/20211220141159.16117-20-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Detect asynchronous reset that occurred in the firmware by polling for
reset history bit of IOC status register is set and if that bit is set,
then the driver waits for the controller to become ready and then
re-initializes the controller.
Also reduce the time driver is waiting for the controller to acknowledge
the reset action after issuing a specific reset action to the
controller. The wait time is reduced from 510 seconds to 30 seconds. If the
controller didn't acknowledge a specific reset action within the time
interval then the driver marks the controller as unrecoverable instead of
retrying two more times prior to giving up.
Link: https://lore.kernel.org/r/20211220141159.16117-17-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver marks the controller as unrecoverable if there is an
asynchronous reset or fault during the initialization, reinitialization
post reset, and OS resume.
Enhance driver to retry the initialization, re-initialization, and resume
sequences for a maximum of 3 times if the controller became faulty or
asynchronously reset due to a firmware activation during the initialization
sequence.
Link: https://lore.kernel.org/r/20211220141159.16117-15-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following special handling is needed for UNMAP commands issued to NVMe
drives:
- On B0 boards, if the parameter list length is greater than 24 and not a
16-byte multiple, then truncate the parameter list length to a 16-byte
multiple.
- On A0 boards, if the parameter list length is greater than block
descriptor data length + 8, then truncate the parameter list length to
block descriptor data length + 8 value.
Link: https://lore.kernel.org/r/20211220141159.16117-10-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add validation for various access statuses prior to exposing attached
target device to the operating system.
Link: https://lore.kernel.org/r/20211220141159.16117-8-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS4 Controller firmware exposes the SES devices in Managed PCIe Switch
as a PCIe Device Type SCSI Device
(MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_SCSI_DEVICE).
Driver is enhanced to handle this device type by:
- Exposing the device to the upper layers and
- Not updating any hardware sectors & virtual boundary settings as these
settings are needed only for NVMe devices.
Link: https://lore.kernel.org/r/20211220141159.16117-7-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't issue the soft reset if internal commands are flushed out with reset
status. Soft reset needs to be issued only if commands are really timed
out.
Link: https://lore.kernel.org/r/20211220141159.16117-4-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, smartpqi, lpfc,
target, megaraid_sas, hisi_sas, qla2xxx) and minor updates and bug
fixes. Notable core changes are the removal of scsi->tag which caused
some churn in obsolete drivers and a sweep through all drivers to call
scsi_done() directly instead of scsi->done() which removes a pointer
indirection from the hot path and a move to register core sysfs files
earlier, which means they're available to KOBJ_ADD processing, which
necessitates switching all drivers to using attribute groups.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYYUfBCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbUJAQDZt4oc
vUx9JpyrdHxxTCuOzVFd8W1oJn0k5ltCBuz4yAD8DNbGhGm93raMSJ3FOOlzLEbP
RG8vBdpxMudlvxAPi/A=
=BSFz
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, smartpqi, lpfc,
target, megaraid_sas, hisi_sas, qla2xxx) and minor updates and bug
fixes.
Notable core changes are the removal of scsi->tag which caused some
churn in obsolete drivers and a sweep through all drivers to call
scsi_done() directly instead of scsi->done() which removes a pointer
indirection from the hot path and a move to register core sysfs files
earlier, which means they're available to KOBJ_ADD processing, which
necessitates switching all drivers to using attribute groups"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: lpfc: Update lpfc version to 14.0.0.3
scsi: lpfc: Allow fabric node recovery if recovery is in progress before devloss
scsi: lpfc: Fix link down processing to address NULL pointer dereference
scsi: lpfc: Allow PLOGI retry if previous PLOGI was aborted
scsi: lpfc: Fix use-after-free in lpfc_unreg_rpi() routine
scsi: lpfc: Correct sysfs reporting of loop support after SFP status change
scsi: lpfc: Wait for successful restart of SLI3 adapter during host sg_reset
scsi: lpfc: Revert LOG_TRACE_EVENT back to LOG_INIT prior to driver_resource_setup()
scsi: ufs: ufshcd-pltfrm: Fix memory leak due to probe defer
scsi: ufs: mediatek: Avoid sched_clock() misuse
scsi: mpt3sas: Make mpt3sas_dev_attrs static
scsi: scsi_transport_sas: Add 22.5 Gbps link rate definitions
scsi: target: core: Stop using bdevname()
scsi: aha1542: Use memcpy_{from,to}_bvec()
scsi: sr: Add error handling support for add_disk()
scsi: sd: Add error handling support for add_disk()
scsi: target: Perform ALUA group changes in one step
scsi: target: Replace lun_tg_pt_gp_lock with rcu in I/O path
scsi: target: Fix alua_tg_pt_gps_count tracking
scsi: target: Fix ordered tag handling
...
When scanning devices through the 'scan' attribute in sysfs, the user will
observe duplicate device entries in lsscsi command output.
Set the shost's max_channel to zero to avoid this.
Link: https://lore.kernel.org/r/20211014055425.30719-1-sreekanth.reddy@broadcom.com
Fixes: 824a156633 ("scsi: mpi3mr: Base driver code")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is not setting up IRQs in the resume path. As a result, hibernation
path is broken and controller will not be operational after system is
resumed.
Set up IRQs to handle the hibernation case.
Link: https://lore.kernel.org/r/20210818081755.1274470-1-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Cc: thenzl@redhat.com
Reported-by: Marco Patalano <mpatalan@redhat.com>
Tested-by: Marco Patalano <mpatalan@redhat.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prepare for removal of the request pointer by using scsi_cmd_to_rq()
instead. This patch does not change any functionality.
Link: https://lore.kernel.org/r/20210809230355.8186-30-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following warning reported by static analysis tool smatch:
smatch warnings:
drivers/scsi/mpi3mr/mpi3mr_os.c:873 mpi3mr_update_tgtdev() error: we
previously assumed 'mrioc->shost' could be null (see line 870
Link: https://lore.kernel.org/r/20210629141153.3158-1-sreekanth.reddy@broadcom.com
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following warnings:
drivers/scsi/mpi3mr/mpi3mr_os.c:24:5: warning: symbol 'prot_mask' was not declared. Should it be static?
drivers/scsi/mpi3mr/mpi3mr_os.c:28:5: warning: symbol 'prot_guard_mask' was not declared. Should it be static?
drivers/scsi/mpi3mr/mpi3mr_os.c:31:5: warning: symbol 'logging_level' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20210604071407.1360742-1-yangyingliang@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix a double free, scsi_tgt_priv_data will be freed in
mpi3mr_target_destroy() so remove the kfree() from mpi3mr_target_alloc().
I've also removed few unneeded initialisations.
Link: https://lore.kernel.org/r/20210608145712.16386-1-thenzl@redhat.com
Acked-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
fall-through warning by explicitly adding a break statement instead of just
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Link: https://lore.kernel.org/r/20210604023530.GA180997@embeddedor
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Include Hannes' SCSI command result rework in the staging branch.
[mkp: remove DRIVER_SENSE from mpi3mr]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Read PCI_EXT_CAP_ID_DSN to query security status.
The driver will throw a warning message when a non-secure type controller
is detected. The purpose of this interface is to avoid interacting with any
firmware which is not secured/signed by Broadcom. Any tampering on
firmware component will be detected by hardware and it will be communicated
to the driver to avoid any further interaction with that component.
Link: https://lore.kernel.org/r/20210520152545.2710479-23-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Wait for host I/O completion (default 180 seconds) if I/O timeout is
detected on VDs.
Link: https://lore.kernel.org/r/20210520152545.2710479-21-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The controller hardware can not handle certain UNMAP commands for NVMe
drives. Add support in the driver for checking those commands and handle
them appropriately.
Link: https://lore.kernel.org/r/20210520152545.2710479-17-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of driver returning DID_NO_CONNECT during driver unload allow SSU
and Sync Cache commands to be sent to the controller to flush any cached
data from the drive.
Link: https://lore.kernel.org/r/20210520152545.2710479-16-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Detection of firmware fault or any kind of unresponsiveness in the
controller (any admin command which times out) results in resetting the
controller. The primary reset mechanisms used are either soft reset or diag
fault reset. A reset is performed if the host sets the ResetAction field in
the HostDiagnostic register to either 001b (soft reset) or 007b (diag fault
reset). After successfully resetting the controller the driver
reinitializes the controller by going through start of the day
initialization procedure. Pending I/Os during the reset are returned back
to the SCSI midlayer for retry.
Link: https://lore.kernel.org/r/20210520152545.2710479-10-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.co
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement support for handling the following MPI events:
- MPI3_EVENT_SAS_BROADCAST_PRIMITIVE
- MPI3_EVENT_CABLE_MGMT
- MPI3_EVENT_ENERGY_PACK_CHANGE
Link: https://lore.kernel.org/r/20210520152545.2710479-9-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement support for the following PCIe-related MPI events:
- MPI3_EVENT_PCIE_TOPOLOGY_CHANGE_LIST
- MPI3_EVENT_PCIE_ENUMERATION
Link: https://lore.kernel.org/r/20210520152545.2710479-8-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware can report various MPI Events. Enable support for processing the
following events related to device addition/removal to the driver:
- MPI3_EVENT_DEVICE_ADDED
- MPI3_EVENT_DEVICE_INFO_CHANGED
- MPI3_EVENT_DEVICE_STATUS_CHANGE
- MPI3_EVENT_ENCL_DEVICE_STATUS_CHANGE
- MPI3_EVENT_SAS_TOPOLOGY_CHANGE_LIST
- MPI3_EVENT_SAS_DISCOVERY
- MPI3_EVENT_SAS_DEVICE_DISCOVERY_ERROR
Link: https://lore.kernel.org/r/20210520152545.2710479-7-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The watchdog thread is the driver's internal thread which does a few things
such as detecting firmware faults, resetting the controller, performing
timestamp sync, etc.
Link: https://lore.kernel.org/r/20210520152545.2710479-6-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Send Port Enable Request to FW for Device Discovery. As part of port
enable completion driver calls scan_start and scan_finished hooks. SCSI
layer references like sdev, starget, etc. are added but actual device
discovery will be supported once driver adds complete event process
handling.
Link: https://lore.kernel.org/r/20210520152545.2710479-5-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Cc: hare@suse.de
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create operational request and reply queue pair.
The MPI3 transport interface consists of an Administrative Request Queue,
an Administrative Reply Queue, and Operational Messaging Queues. The
Operational Messaging Queues are the primary communication mechanism
between the host and the I/O Controller (IOC). Request messages, allocated
in host memory, identify I/O operations to be performed by the IOC. These
operations are queued on an Operational Request Queue by the host driver.
Reply descriptors track I/O operations as they complete. The IOC queues
these completions in an Operational Reply Queue.
To fulfil large contiguous memory requirement, driver creates multiple
segments and provide the list of segments. Each segment size should be 4K
which is a hardware requirement. An element array is contiguous or
segmented. A contiguous element array is located in contiguous physical
memory. A contiguous element array must be aligned on an element size
boundary. An element's physical address within the array may be directly
calculated from the base address, the Producer/Consumer index, and the
element size.
Expected phased identifier bit is used to find out valid entry on reply
queue. Driver sets <ephase> bit and IOC inverts the value of this bit on
each pass.
Link: https://lore.kernel.org/r/20210520152545.2710479-4-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement basic pci device driver requirements: Device probing, memory
allocation, mapping system registers, allocate irq lines, etc.
Source is managed in mainly three different files:
- mpi3mr_fw.c: Common code which interacts with underlying fw/hw.
- mpi3mr_os.c: Common code which interacts with SCSI midlayer.
- mpi3mr_app.c: Common code which interacts with application/ioctl.
This is currently work in progress.
Link: https://lore.kernel.org/r/20210520152545.2710479-3-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Cc: bvanassche@acm.org
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
