Update lpfc version to 12.8.0.10
Link: https://lore.kernel.org/r/20210514195559.119853-12-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FC-LS-5 specifies that a received RDF implies a possible change to fabric
supported diagnostic functions. Endpoints are to re-perform the RDF
exchange with the fabric to enable possible new features or adapt to
changes in values.
This patch adds the logic to RDF receive to re-perform the RDF exchange
with the switch.
Link: https://lore.kernel.org/r/20210514195559.119853-11-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Default behavior for the driver, when aborting an I/O, is to terminate the
I/O with the adapter. The adapter will initiate an ABTS to terminate the
exchange on the link and mark the exchange is terminated so that no further
use of the sgl or any traffic for the exchange is worked on. Completion on
the Abort is then posted to the driver, which as the I/O is terminated can
complete the I/O to the OS. This completion may occur prior to the ABTS
handshake completing on the wire. The ABTS handshake can take a long time
to complete with timeouts and retries reaching 60+ seconds. Note: if
retries fail, LOGO occurs.
Some devices want to ensure that the ABTS handshake fully completes (this
device has fully ack'd it) before the I/O completion is posted back to the
OS, where a failed I/O may be retried via a different path.
To support this behavior, an option was added to the driver to change I/O
completion from the Abort cmd completion to the Exchange termination (aka
ABTS) completion.
Link: https://lore.kernel.org/r/20210514195559.119853-10-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is encountering a crash in lpfc_free_iocb_list() while
performing initial attachment.
Code review found this to be an errant failure path that was taken, jumping
to a tag that then referenced structures that were uninitialized.
Fix the failure path.
Link: https://lore.kernel.org/r/20210514195559.119853-9-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a link bounce happens, there is a possibility that responses to
requests posted prior to the link bounce could be received. This is
problematic as the counter to track reglogin completion after link up can
become out of sync with the real state.
As there is no reason to process a request made in a prior link up context,
eliminate all the disturbance by tagging the request with the event_tag
maintained by the SLI Port for the link. The event_tag will change on every
link state transition. As long as the tag matches the current event_tag,
the response can be processed. If it doesn't match, just discard the
response.
Link: https://lore.kernel.org/r/20210514195559.119853-8-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During link bounce testing, RPI counts were seen to differ from the number
of nodes. For fabric and domain controllers, a temporary RPI is assigned,
but the code isn't registering it. If the nodes do go away, such as on link
down, the temporary RPI isn't being released.
Change the way these two fabric services are managed, make them behave like
any other remote port. Register the RPI and register with the transport.
Never leave the nodes in a NPR or UNUSED state where their RPI is in limbo.
This allows them to follow normal dev_loss_tmo handling, RPI refcounting,
and normal removal rules. It also allows fabric I/Os to use the RPI for
traffic requests.
Note: There is some logic that still has a couple of exceptions when the
Domain controller (0xfffcXX). There are cases where the fabric won't have a
valid login but will send RDP. Other times, it will it send a LOGO then an
RDP. It makes for ad-hoc behavior to manage the node. Exceptions are
documented in the code.
Link: https://lore.kernel.org/r/20210514195559.119853-7-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When lpfc is handling a solicited and unsolicited PLOGI with another
initiator, the remote initiator is never recovered. The node for the
initiator is erroneouosly removed and all resources released.
In lpfc_cmpl_els_plogi(), when lpfc_els_retry() returns a failure code, the
driver is calling the state machine with a device remove event because the
remote port is not currently registered with the SCSI or NVMe
transports. The issue is that on a PLOGI "collision" the driver correctly
aborts the solicited PLOGI and allows the unsolicited PLOGI to complete the
process, but this process is interrupted with a device_rm event.
Introduce logic in the PLOGI completion to capture the PLOGI collision
event and jump out of the routine. This will avoid removal of the node.
If there is no collision, the normal node removal will occur.
Fixes: 52edb2caf6 ("scsi: lpfc: Remove ndlp when a PLOGI/ADISC/PRLI/REG_RPI ultimately fails")
Cc: <stable@vger.kernel.org> # v5.11+
Link: https://lore.kernel.org/r/20210514195559.119853-6-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is crashing due to a bad pointer during driver load due in an
adisc acc receive routine. The driver is missing node get/put in the
mbx_resume_rpi paths.
Fix by adding the proper gets and puts into the resume_rpi path.
Link: https://lore.kernel.org/r/20210514195559.119853-5-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An 'unexpected timeout' message may be seen in a point-2-point topology.
The message occurs when a PLOGI is received before the driver is notified
of FLOGI completion. The FLOGI completion failure causes discovery to be
triggered for a second time. The discovery timer is restarted but no new
discovery activity is initiated, thus the timeout message eventually
appears.
In point-2-point, when discovery has progressed before the FLOGI completion
is processed, it is not a failure. Add code to FLOGI completion to detect
that discovery has progressed and exit the FLOGI handling (noop'ing it).
Link: https://lore.kernel.org/r/20210514195559.119853-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When processing an NVMe ERSP IU which didn't match the optimized CQE-only
path, the status was being left to the WQE status. WQE status is non-zero
as it is indicating a non-optimized completion that needs to be handled by
the driver.
Fix by clearing the status field when falling into the non-optimized
case. Log message added to track optimized vs non-optimized debug.
Link: https://lore.kernel.org/r/20210514195559.119853-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While testing NPIV and watching logins and used RPI levels, it was seen the
used RPI count was much higher than the number of remote ports discovered.
Code inspection showed that remote port removals on any NPIV instance are
releasing the RPI, but not performing an UNREG_RPI with the adapter thus
the reference counting never fully drops and the RPI is never fully
released. This was happening on NPIV nodes due to a log of fabric ELS's to
fabric addresses. This lack of UNREG_RPI was introduced by a prior node
rework patch that performed the UNREG_RPI as part of node cleanup.
To resolve the issue, do the following:
- Restore the RPI release code, but move the location to so that it is in
line with the new node cleanup design.
- NPIV ports now release the RPI and drop the node when the caller sets
the NLP_RELEASE_RPI flag.
- Set the NLP_RELEASE_RPI flag in node cleanup which will trigger a
release of RPI to free pool.
- Ensure there's an UNREG_RPI at LOGO completion so that RPI release is
completed.
- Stop offline_prep from skipping nodes that are UNUSED. The RPI may
not have been released.
- Stop the default RPI handling in lpfc_cmpl_els_rsp() for SLI4.
- Fixed up debugfs RPI displays for better debugging.
Fixes: a70e63eee1 ("scsi: lpfc: Fix NPIV Fabric Node reference counting")
Link: https://lore.kernel.org/r/20210514195559.119853-2-jsmart2021@gmail.com
Cc: <stable@vger.kernel.org> # v5.11+
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With commit 312c004d36 ("[PATCH] driver core: replace "hotplug" by
"uevent"") already in the tree over a decade, update the name of
FW_ACTION defines to follow semantics, and reflect what the defines are
really meant for, i.e. whether or not generate user space event.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210425020024.28057-1-shawn.guo@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer tmp_hdr is being assigned a value that is never read, the
assignment is redundant and can be removed.
Link: https://lore.kernel.org/r/20210420104123.376420-1-colin.king@canonical.com
Addresses-Coverity: ("Unused value")
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The dump command for reading a region passes a requested read length
specified in words (4-byte units). The response overwrites the same field
with the actual number of bytes read.
The mailbox handler for DUMP which reads VPD data (region 23) is treating
the response field as if it were still a word_cnt, thus multiplying it by 4
to set the read's "length". Given the read value was calculated based on
the size of the read buffer, the longer response length runs off the end of
the buffer.
Fix by reworking the code to use the response field as a byte count.
Link: https://lore.kernel.org/r/20210421234511.102206-1-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_bsg_ct_unsol_event() routine acts assigns a ct_request to the wrong
structure address, resulting in a bad address that results in bsg related
timeouts.
Correct the ct_request assignment to use the kernel virtual buffer address
(not the control structure address).
Link: https://lore.kernel.org/r/20210421234448.102132-1-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In devloss timer handler and in backend calls to terminate remote port I/O,
there is logic to walk through all active IOCBs and validate them to
potentially trigger an abort request. This logic is causing illegal memory
accesses which leads to a crash. Abort IOCBs, which may be on the list, do
not have an associated lpfc_io_buf struct. The driver is trying to map an
lpfc_io_buf struct on the IOCB and which results in a bogus address thus
the issue.
Fix by skipping over ABORT IOCBs (CLOSE IOCBs are ABORTS that don't send
ABTS) in the IOCB scan logic.
Link: https://lore.kernel.org/r/20210421234433.102079-1-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update copyrights to 2021 for files modified in the 12.8.0.9 patch set.
Link: https://lore.kernel.org/r/20210412013127.2387-17-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.8.0.9
Link: https://lore.kernel.org/r/20210412013127.2387-16-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During code inspection, several cases of creating a dynamic attribute names
in logs messages using a define was found. This is unnecessary.
Place the native symbol name in the log messages.
Link: https://lore.kernel.org/r/20210412013127.2387-15-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code inspection showed lpfc was using three different pointer formats when
logging discovery object pointers.
Standardize the pointer format to x%px.
Note: %px use is limited to discovery objects in order to aid core
analysis.
Link: https://lore.kernel.org/r/20210412013127.2387-14-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clean up minor issues spotted by tools and code review:
- Spelling Errors
- Spurious characters and errors in function headers
- nvme_info wqerr and err fields source data reversed
- Extraneous new line in log message 0466
- Spacing error in log message 0109
- Messages 0140 and 0141 have portname and nodename reversed
- Incorrect function labelling in comment
Link: https://lore.kernel.org/r/20210412013127.2387-13-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SLI-4 does not contain a PORT_CAPABILITIES mailbox command (only SLI-3
does, and SLI-3 doesn't use it), yet there are SLI-4 code paths that have
code to issue the command. The command will always fail.
Remove the code for the mailbox command and leave only the resulting
"failure path" logic.
Link: https://lore.kernel.org/r/20210412013127.2387-12-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc_hdw_queue attribute is to set the number of hardware queues to be
created on the adapter. Normally, the value is set to a default, which
allows the hw queue count to be sized dynamically based on adapter
capabilities, CPU/platform architecture, or CPU type. Currently, when
lpfc_hdw_queue is set to a specific value, is has no effect and the dynamic
sizing occurs.
The routine checking whether parameters are default or not ignores the
lpfc_hdw_queue setting and invokes the dynamic logic.
Fix the routine to additionally check the lpfc_hdw_queue attribute value
before using dynamic scaling. Additionally, SLI-3 supports only a small
number of queues with dedicated functions, thus it needs to be exempted
from the variable scaling and set to the expected values.
Link: https://lore.kernel.org/r/20210412013127.2387-11-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FDMI registration needs to be performed after every login with the FC Mgmt
service. The flag the driver is using to track registration is cleared on
link up, but never on Mgmt service logout/re-login.
Fix by clearing the flag whenever a new login is completed with the FC Mgmt
service.
While perusing the flag use, logging was performed as if FDMI registration
occurred on vports. However, it is limited to the physical port only.
Revise the logging to reflect physical port based.
Link: https://lore.kernel.org/r/20210412013127.2387-10-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the unlikely case of a failure to allocate an LPFC_MBOXQ_t structure, no
return status is set, thus the routine never logs an error and returns
success to the callee.
Fix by setting a return code on failure.
Link: https://lore.kernel.org/r/20210412013127.2387-9-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During target port swap, the swap logic ignores the DROPPED flag in the
nodes. As a node then moves into the UNUSED state, the reference count will
be dropped. If a node is later reused and moved out of the UNUSED state, an
access can result in a use-after-free assert.
Fix by having the port swap logic propagate the DROPPED flag when switching
nodes. This will avoid reference from being dropped.
Link: https://lore.kernel.org/r/20210412013127.2387-8-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In SLI-4, when performing a mailbox command with MBX_POLL, the driver uses
the BMBX register to send the command rather than the MQ. A flag is set
indicating the BMBX register is active and saves the mailbox job struct
(mboxq) in the mbox_active element of the adapter. The routine then waits
for completion or timeout. The mailbox job struct is not freed by the
routine. In cases of timeout, the adapter will be reset. The
lpfc_sli_mbox_sys_flush() routine will clean up the mbox in preparation for
the reset. It clears the BMBX active flag and marks the job structure as
MBX_NOT_FINISHED. But, it never frees the mboxq job structure. Expectation
in both normal completion and timeout cases is that the issuer of the mbx
command will free the structure. Unfortunately, not all calling paths are
freeing the memory in cases of error.
All calling paths were looked at and updated, if missing, to free the mboxq
memory regardless of completion status.
Link: https://lore.kernel.org/r/20210412013127.2387-7-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During target port-swap testing with link flips, the initiator could
encounter PRLI errors. If the target node disappears permanently, the ndlp
is found stuck in UNUSED state with ref count of 1. The rmmod of the driver
will hang waiting for this node to be freed.
While handling a link error in PRLI completion path, the code intends to
skip triggering the discovery state machine. However this is causing the
final reference release path to be skipped. This causes the node to be
stuck with ref count of 1
Fix by ensuring the code path triggers the device removal event on the node
state machine.
Link: https://lore.kernel.org/r/20210412013127.2387-6-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove hbalock dependency for lpfc_abts_els_sgl_list and
lpfc_abts_nvmet_ctx_list. The lists are adaquately synchronized with the
sgl_list_lock and abts_nvmet_buf_list_lock.
Link: https://lore.kernel.org/r/20210412013127.2387-5-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Call traces are being seen that result from a nodelist structure ref
counting error. They are typically seen after transmission of an LS_RJT ELS
response.
Aged code in lpfc_cmpl_els_rsp() calls lpfc_nlp_not_used() which, if the
ndlp reference count is exactly 1, will decrement the reference count.
Previously lpfc_nlp_put() was within lpfc_els_free_iocb(), and the 'put'
within the free would only be invoked if cmdiocb->context1 was not NULL.
Since the nodelist structure reference count is decremented when exiting
lpfc_cmpl_els_rsp() the lpfc_nlp_not_used() calls are no longer required.
Calling them is causing the reference count issue.
Fix by removing the lpfc_nlp_not_used() calls.
Link: https://lore.kernel.org/r/20210412013127.2387-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix a crash caused by a double put on the node when the driver completed an
ACC for an unsolicted abort on the same node. The second put was executed
by lpfc_nlp_not_used() and is wrong because the completion routine executes
the nlp_put when the iocbq was released. Additionally, the driver is
issuing a LOGO then immediately calls lpfc_nlp_set_state to put the node
into NPR. This call does nothing.
Remove the lpfc_nlp_not_used call and additional set_state in the
completion routine. Remove the lpfc_nlp_set_state post issue_logo. Isn't
necessary.
Link: https://lore.kernel.org/r/20210412013127.2387-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rmmod on SLI-4 adapters is sometimes hitting a bad ptr dereference in
lpfc_els_free_iocb().
A prior patch refactored the lpfc_sli_abort_iocb() routine. One of the
changes was to convert from building/sending an abort within the routine to
using a common routine. The reworked routine passes, without modification,
the pring ptr to the new common routine. The older routine had logic to
check SLI-3 vs SLI-4 and adapt the pring ptr if necessary as callers were
passing SLI-3 pointers even when not on an SLI-4 adapter. The new routine
is missing this check and adapt, so the SLI-3 ring pointers are being used
in SLI-4 paths.
Fix by cleaning up the calling routines. In review, there is no need to
pass the ring ptr argument to abort_iocb at all. The routine can look at
the adapter type itself and reference the proper ring.
Link: https://lore.kernel.org/r/20210412013127.2387-2-jsmart2021@gmail.com
Fixes: db7531d2b3 ("scsi: lpfc: Convert abort handling to SLI-3 and SLI-4 handlers")
Cc: <stable@vger.kernel.org> # v5.11+
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull 5.12/scsi-fixes into the 5.13 SCSI tree to provide a baseline for
some UFS changes that would otherwise cause conflicts during the
merge.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gcc-11 warns about an strnlen with a length larger than the size of the
passed buffer:
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_nvme_info_show':
drivers/scsi/lpfc/lpfc_attr.c:518:25: error: 'strnlen' specified bound 4095 exceeds source size 24 [-Werror=stringop-overread]
518 | strnlen(LPFC_NVME_INFO_MORE_STR, PAGE_SIZE - 1)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In this case, the code is entirely valid, as the string is properly
terminated, and the size argument is only there out of extra caution in
case it exceeds a page.
This cannot really happen here, so just simplify it to a sizeof().
Link: https://lore.kernel.org/r/20210322160253.4032422-10-arnd@kernel.org
Fixes: afff0d2321 ("scsi: lpfc: Add Buffer overflow check, when nvme_info larger than PAGE_SIZE")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If copy_from_user() or kstrtoull() fail then the correct behavior is to
return a negative error code.
Link: https://lore.kernel.org/r/YEsbU/UxYypVrC7/@mwanda
Fixes: f9bb2da11d ("[SCSI] lpfc 8.3.27: T10 additions for SLI4")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvme.c:2021: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_create_localport'
Link: https://lore.kernel.org/r/20210312094738.2207817-16-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_bsg.c:3591: warning: expecting prototype for lpfc_bsg_mbox_ext_cleanup(). Prototype was for lpfc_bsg_mbox_ext_session_reset() instead
drivers/scsi/lpfc/lpfc_bsg.c:3885: warning: expecting prototype for lpfc_bsg_sli_cfg_mse_read_cmd_ext(). Prototype was for lpfc_bsg_sli_cfg_read_cmd_ext() instead
drivers/scsi/lpfc/lpfc_bsg.c:4371: warning: expecting prototype for lpfc_bsg_mbox_ext_abort_req(). Prototype was for lpfc_bsg_mbox_ext_abort() instead
Link: https://lore.kernel.org/r/20210312094738.2207817-14-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_debugfs.c:405: warning: expecting prototype for lpfc_debugfs_common_xri_data(). Prototype was for lpfc_debugfs_commonxripools_data() instead
Link: https://lore.kernel.org/r/20210312094738.2207817-13-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_attr.c:880: warning: expecting prototype for lpfc_state_show(). Prototype was for lpfc_link_state_show() instead
drivers/scsi/lpfc/lpfc_attr.c:3834: warning: expecting prototype for lpfc_tgt_queue_depth_store(). Prototype was for lpfc_tgt_queue_depth_set() instead
drivers/scsi/lpfc/lpfc_attr.c:4027: warning: expecting prototype for lpfc_topology_set(). Prototype was for lpfc_topology_store() instead
drivers/scsi/lpfc/lpfc_attr.c:4481: warning: expecting prototype for lpfc_link_speed_set(). Prototype was for lpfc_link_speed_store() instead
drivers/scsi/lpfc/lpfc_attr.c:4879: warning: expecting prototype for lpfc_request_firmware_store(). Prototype was for lpfc_request_firmware_upgrade_store() instead
drivers/scsi/lpfc/lpfc_attr.c:5235: warning: expecting prototype for lpfc_state_show(). Prototype was for lpfc_fcp_cpu_map_show() instead
Link: https://lore.kernel.org/r/20210312094738.2207817-5-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_scsi.c:746: warning: expecting prototype for lpfc_release_scsi_buf(). Prototype was for lpfc_release_scsi_buf_s3() instead
drivers/scsi/lpfc/lpfc_scsi.c:979: warning: expecting prototype for App checking is required for(). Prototype was for BG_ERR_CHECK() instead
drivers/scsi/lpfc/lpfc_scsi.c:3701: warning: Function parameter or member 'vport' not described in 'lpfc_scsi_prep_cmnd_buf'
drivers/scsi/lpfc/lpfc_scsi.c:3701: warning: Excess function parameter 'phba' description in 'lpfc_scsi_prep_cmnd_buf'
drivers/scsi/lpfc/lpfc_scsi.c:3717: warning: Function parameter or member 'fcpi_parm' not described in 'lpfc_send_scsi_error_event'
drivers/scsi/lpfc/lpfc_scsi.c:3717: warning: Excess function parameter 'rsp_iocb' description in 'lpfc_send_scsi_error_event'
drivers/scsi/lpfc/lpfc_scsi.c:3837: warning: Function parameter or member 'fcpi_parm' not described in 'lpfc_handle_fcp_err'
drivers/scsi/lpfc/lpfc_scsi.c:3837: warning: expecting prototype for lpfc_handler_fcp_err(). Prototype was for lpfc_handle_fcp_err() instead
drivers/scsi/lpfc/lpfc_scsi.c:4021: warning: Function parameter or member 'wcqe' not described in 'lpfc_fcp_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_scsi.c:4021: warning: Excess function parameter 'pwqeOut' description in 'lpfc_fcp_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_scsi.c:4621: warning: Function parameter or member 'vport' not described in 'lpfc_scsi_prep_cmnd_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:4621: warning: Excess function parameter 'phba' description in 'lpfc_scsi_prep_cmnd_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:4698: warning: Function parameter or member 'vport' not described in 'lpfc_scsi_prep_cmnd_buf_s4'
drivers/scsi/lpfc/lpfc_scsi.c:4698: warning: Excess function parameter 'phba' description in 'lpfc_scsi_prep_cmnd_buf_s4'
drivers/scsi/lpfc/lpfc_scsi.c:4954: warning: expecting prototype for lpfc_taskmgmt_def_cmpl(). Prototype was for lpfc_tskmgmt_def_cmpl() instead
drivers/scsi/lpfc/lpfc_scsi.c:5094: warning: expecting prototype for lpfc_poll_rearm_time(). Prototype was for lpfc_poll_rearm_timer() instead
Link: https://lore.kernel.org/r/20210312094738.2207817-4-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_hbadisc.c:1505: warning: expecting prototype for lpfc_update_fcf_record(). Prototype was for __lpfc_update_fcf_record() instead
Link: https://lore.kernel.org/r/20210303144631.3175331-28-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_ct.c:153: warning: Function parameter or member 'ct_req' not described in 'lpfc_ct_reject_event'
drivers/scsi/lpfc/lpfc_ct.c:153: warning: Function parameter or member 'rx_id' not described in 'lpfc_ct_reject_event'
drivers/scsi/lpfc/lpfc_ct.c:153: warning: Function parameter or member 'ox_id' not described in 'lpfc_ct_reject_event'
drivers/scsi/lpfc/lpfc_ct.c:283: warning: Function parameter or member 'ctiocbq' not described in 'lpfc_ct_handle_mibreq'
drivers/scsi/lpfc/lpfc_ct.c:283: warning: Excess function parameter 'ctiocb' description in 'lpfc_ct_handle_mibreq'
Link: https://lore.kernel.org/r/20210303144631.3175331-26-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_sli.c:9654: warning: expecting prototype for lpfc_sli_iocb2wqe(). Prototype was for lpfc_sli4_iocb2wqe() instead
drivers/scsi/lpfc/lpfc_sli.c:10439: warning: Function parameter or member 'phba' not described in 'lpfc_sli_issue_fcp_io'
drivers/scsi/lpfc/lpfc_sli.c:10439: warning: Function parameter or member 'ring_number' not described in 'lpfc_sli_issue_fcp_io'
drivers/scsi/lpfc/lpfc_sli.c:10439: warning: Function parameter or member 'piocb' not described in 'lpfc_sli_issue_fcp_io'
drivers/scsi/lpfc/lpfc_sli.c:10439: warning: Function parameter or member 'flag' not described in 'lpfc_sli_issue_fcp_io'
drivers/scsi/lpfc/lpfc_sli.c:14189: warning: expecting prototype for lpfc_sli4_sp_process_cq(). Prototype was for __lpfc_sli4_sp_process_cq() instead
drivers/scsi/lpfc/lpfc_sli.c:14754: warning: expecting prototype for lpfc_sli4_hba_process_cq(). Prototype was for lpfc_sli4_dly_hba_process_cq() instead
drivers/scsi/lpfc/lpfc_sli.c:17230: warning: expecting prototype for lpfc_sli4_free_xri(). Prototype was for __lpfc_sli4_free_xri() instead
drivers/scsi/lpfc/lpfc_sli.c:18950: warning: expecting prototype for lpfc_sli4_free_rpi(). Prototype was for __lpfc_sli4_free_rpi() instead
Link: https://lore.kernel.org/r/20210303144631.3175331-18-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-scsi@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For the files modified in 2021 via the 12.8.0.7 and 12.8.0.8 patch sets,
update the copyright for 2021.
Link: https://lore.kernel.org/r/20210301171821.3427-23-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.8.0.8.
Link: https://lore.kernel.org/r/20210301171821.3427-22-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code inspection revealed stale comments in function headers for functions
that call lpfc_prep_els_iocb(). Changes in ndlp reference counting were not
reflected in function headers.
Update the stale comments in function headers to more accurately indicate
ndlp reference counting.
Link: https://lore.kernel.org/r/20210301171821.3427-21-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Lots of discovery messages are flooding the console log when testing NPIV.
Informational message for vports should have LOG_VPORT associated with it
as opposed to LOG_TRACE_EVENT.
Link: https://lore.kernel.org/r/20210301171821.3427-20-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Message 8347 Invalid device found log message is logged when an LPe12000
adapter is installed. The log message is supposed to indicate an
unsupported pci reset adapter rather than an invalid device.
Change the wording to: Incapable PCI reset device.
Link: https://lore.kernel.org/r/20210301171821.3427-19-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is causing a crash in __lpfc_sli_release_iocbq_s4() when it
dereferences the els_wq which is NULL.
Validate the pring for the els_wq before dereferencing. Reorg the code to
move the pring assignment closer to where it is actually used.
Link: https://lore.kernel.org/r/20210301171821.3427-18-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On a setup with a dual port HBA and both ports direct connected, an rmmod
hangs momentarily when we log an Illegal State Transition. Once it resumes,
a nodelist not empty logic is hit, which forces rmmod to cleanup and exit.
We're missing a state transition case in the discovery engine.
Fix by adding a case for a DEVICE_RM event while in the unmapped state to
avoid illegal state transition log message.
Link: https://lore.kernel.org/r/20210301171821.3427-17-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The debugfs nodeinfo output gets jumbled when no rpri or a defer entry is
displayed. The misalignment makes it difficult to read.
Change the format to consistently print out a 4 character rpi, and turn
defer into a suffix.
Link: https://lore.kernel.org/r/20210301171821.3427-16-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While testing target port swap test with ADISC enabled, several nodes
remain in UNUSED state. These nodes are never freed and rmmod hangs for
long time before finising with "0233 Nodelist not empty" error.
During PLOGI completion lpfc_plogi_confirm_nport() looks for existing nodes
with same WWPN. If found, the existing node is used to continue discovery.
The node on which plogi was performed is freed. When ADISC is enabled, an
ADISC els request is triggered in response to an RSCN. It's possible that
the ADISC may be rejected by the remote port causing the ADISC completion
handler to clear the port and node name in the node. If this occurs, if a
PLOGI is received it causes a node lookup based on wwpn to now fail,
causing the port swap logic to kick in which allocates a new node and swaps
to it. This effectively orphans the original node structure.
Fix the situation by detecting when the lookup fails and forgo the node
swap and node allocation by using the node on which the PLOGI was issued.
Link: https://lore.kernel.org/r/20210301171821.3427-15-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is seeing a scenario where PLOGI response was issued and traffic
is arriving while the adapter is still setting up the login context. This
is resulting in errors handling the traffic.
Change the driver so that PLOGI response is sent after the login context
has been setup to avoid the situation.
Link: https://lore.kernel.org/r/20210301171821.3427-14-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When connected in pt2pt mode, there is a scenario where the remote port
significantly delays sending a response to our FLOGI, but acts on the FLOGI
it sent us and proceeds to PLOGI/PRLI. The FLOGI ends up timing out and
kicks off recovery logic. End result is a lot of unnecessary state changes
and lots of discovery messages being logged.
Fix by terminating the FLOGI and noop'ing its completion if we have already
accepted the remote ports FLOGI and are now processing PLOGI.
Link: https://lore.kernel.org/r/20210301171821.3427-13-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An unlikely error exit path from lpfc_els_retry() returns incorrect status
to a caller, erroneously indicating that a retry has been successfully
issued or scheduled.
Change error exit path to indicate no retry.
Link: https://lore.kernel.org/r/20210301171821.3427-12-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several code paths where the following sequence occurs:
- An ndlp pointer is assigned to an iocb via a nlp_get()
- An attempt is made to issue the iocb, but it fails
- The failure case does a put on the ndlp then calls lpfc_els_free_iocb()
The put may free the ndlp structure, but the els_free_iocb may reference
the now-stale ndlp pointer and cause a crash.
Fix by ensuring that the lpfc_els_free_iocb() occurs before the
lpfc_nlp_put().
While fixing, refactor the code to better ensure this calling sequence.
Link: https://lore.kernel.org/r/20210301171821.3427-11-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is possible to call lpfc_issue_els_plogi() passing a did for which no
matching ndlp is found. A call is then made to lpfc_prep_els_iocb() with a
null pointer to a lpfc_nodelist structure resulting in a null pointer
dereference.
Fix by returning an error status if no valid ndlp is found. Fix up comments
regarding ndlp reference counting.
Link: https://lore.kernel.org/r/20210301171821.3427-10-jsmart2021@gmail.com
Fixes: 4430f7fd09 ("scsi: lpfc: Rework locations of ndlp reference taking")
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_fcp_io_cmd_wqe_cmpl() is intended to mirror
lpfc_nvme_io_cmd_wqe_cmpl() for sli4 fcp completions. When the routine was
added, lpfc_fcp_io_cmd_wqe_cmpl() included a null pointer check for
phba. However, phba is definitely valid, being dereferenced by the calling
routine and used later in the routine itself.
Remove the unnecessary null check.
Link: https://lore.kernel.org/r/20210301171821.3427-9-jsmart2021@gmail.com
Fixes: 96e209be6e ("scsi: lpfc: Convert SCSI I/O completions to SLI-3 and SLI-4 handlers")
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On a pt2pt setup, between 2 initiators, if one side issues a a LOGO, there
is no relogin attempt. The FC specs are grey in this area on which port
(higher wwn or not) is to re-login.
As there is no spec guidance, unconditionally re-PLOGI after the logout to
ensure a login is re-established.
Link: https://lore.kernel.org/r/20210301171821.3427-8-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver crashed in lpfc_debugfs_disc_trc() due to null ndlp pointer. In
some calling cases, the ndlp is null and the did is looked up.
Fix by using the local did variable that is set appropriately based on ndlp
value.
Link: https://lore.kernel.org/r/20210301171821.3427-7-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After an initial successful FLOGI into the switch, if a subsequent FLOGI
fails the driver crashed accessing a node struct. On FLOGI error, the flogi
completion logic triggers the final dereference on the node structure
without checking if it is registered with a backend. The devloss logic is
triggered after node is freed leading to the access of freed node.
Fix by adjusting the error path to not take the final dereferece if there
is an outstanding transport registration. Let the transport devloss call
remove the final reference.
Link: https://lore.kernel.org/r/20210301171821.3427-6-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Whenever an RRQ needs to be triggered, the DID from the node structure and
node pointer are stored in the RRQ data structure and the RRQ is scheduled
for later transmission. However, at the point in time that the timer
triggers, there's no validation on the node pointer. Reference counters may
have freed the structure. Additionally the DID in the node may no longer be
valid.
Fix by not tracking the node pointer in the RRQ, only the DID. At the time
of the timer expiration, look up the node with the did and if present, send
the RRQ. If no node exists, no need to send the RRQ.
Link: https://lore.kernel.org/r/20210301171821.3427-5-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An LBA is 8 bytes. The driver generates a reftag from the LBA but the
reftag is 4 bytes. Thus scsi_get_lba() could return a value that exceeds
our reftag size.
Fix by converting all the code to calling the common routine
t10_pi_ref_tag() which returns a u32, thus ensuring a consistent 4byte
value. Also correct a few code lines that access LBA directly and ensure
64-bit data types are used.
Link: https://lore.kernel.org/r/20210301171821.3427-4-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calls to lpfc_find_vport_by_vpid() for the highest indexed vport fails with
error, "2936 Could not find Vport mapped to vpi XXX". Our vport indices in
the loop and if-clauses were off by one.
Correct the vpid range used for vpi lookup to include the highest possible
vpid.
Link: https://lore.kernel.org/r/20210301171821.3427-3-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The wqe_dbde field indicates whether a Data BDE is present in Words 0:2 and
should therefore should be clear in the abts request wqe. By setting the
bit we can be misleading fw into error cases.
Clear the wqe_dbde field.
Link: https://lore.kernel.org/r/20210301171821.3427-2-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, ibmvfc,
qla2xxx, hisi_sas, pm80xx) plus the removal of the gdth driver (which
is bound to cause conflicts with a trivial change somewhere). The
only big major rework of note is the one from Hannes trying to clean
up our result handling code in the drivers to make it consistent.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYDAdliYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishTblAQCk6wD8
fcb4TItSRp0DpRzs37zhppEbrBgveuAFHhr5swEA0gL2mHcq0vnyNBinCLnERrE7
TPYJqUKJNktnjVG7ZWc=
=wW6p
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, ibmvfc,
qla2xxx, hisi_sas, pm80xx) plus the removal of the gdth driver (which
is bound to cause conflicts with a trivial change somewhere).
The only big major rework of note is the one from Hannes trying to
clean up our result handling code in the drivers to make it
consistent"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (194 commits)
scsi: MAINTAINERS: Adjust to reflect gdth scsi driver removal
scsi: ufs: Give clk scaling min gear a value
scsi: lpfc: Fix 'physical' typos
scsi: megaraid_mbox: Fix spelling of 'allocated'
scsi: qla2xxx: Simplify the calculation of variables
scsi: message: fusion: Fix 'physical' typos
scsi: target: core: Change ASCQ for residual write
scsi: target: core: Signal WRITE residuals
scsi: target: core: Set residuals for 4Kn devices
scsi: hisi_sas: Add trace FIFO debugfs support
scsi: hisi_sas: Flush workqueue in hisi_sas_v3_remove()
scsi: hisi_sas: Enable debugfs support by default
scsi: hisi_sas: Don't check .nr_hw_queues in hisi_sas_task_prep()
scsi: hisi_sas: Remove deferred probe check in hisi_sas_v2_probe()
scsi: lpfc: Add auto select on IRQ_POLL
scsi: ncr53c8xx: Fix typos
scsi: lpfc: Fix ancient double free
scsi: qla2xxx: Fix some memory corruption
scsi: qla2xxx: Remove redundant NULL check
scsi: megaraid: Fix ifnullfree.cocci warnings
...
In testing, in a configuration with Redfish and native NVMe multipath when
an EEH is injected, a kernel oops is being encountered:
(unreliable)
lpfc_nvme_ls_req+0x328/0x720 [lpfc]
__nvme_fc_send_ls_req.constprop.13+0x1d8/0x3d0 [nvme_fc]
nvme_fc_create_association+0x224/0xd10 [nvme_fc]
nvme_fc_reset_ctrl_work+0x110/0x154 [nvme_fc]
process_one_work+0x304/0x5d
the NBMe transport is issuing a Disconnect LS request, which the driver
receives and tries to post but the work queue used by the driver is already
being torn down by the eeh.
Fix by validating the validity of the work queue before proceeding with the
LS transmit.
Link: https://lore.kernel.org/r/20210127221601.84878-1-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "pmb" pointer is freed at the start of the function and then freed
again in the error handling code.
Link: https://lore.kernel.org/r/YA6E8rO51hE56SVw@mwanda
Fixes: 92d7f7b0cd ("[SCSI] lpfc: NPIV: add NPIV support on top of SLI-3")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for eh_should_retry_cmd callback in lpfc_template.
Link: https://lore.kernel.org/r/1609969748-17684-6-git-send-email-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following coccicheck warning:
./drivers/scsi/lpfc/lpfc_bsg.c:5392:5-29: WARNING: Comparison to bool
Link: https://lore.kernel.org/r/1610439893-64872-1-git-send-email-abaci-bugfix@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: YANG LI <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.8.0.7
Link: https://lore.kernel.org/r/20210104180240.46824-16-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While testing recent discovery node rework, several items were seen that
could be done better with respect to the new trace event logic.
1) in the following msg:
kernel: lpfc 0000:44:00.0: start 35 end 35 cnt 0
If cnt is zero in the 1st message, there is no reason to display the
1st message, which is just giving start/end positioning.
Fix by not displaying message if cnt is 0.
2) If the driver is loaded with module log verbosity off, and later a
single NPIV host instance verbosity is enabled via sysfs, it enables
messages on all instances. This is due to the trace log verbosity checks
(lpfc_dmp_dbg) looking at the phba only. It should look at the phba and
the vport.
Fix by enabling a check on both phba and vport.
3) in the following messages:
2904 Firmware Dump Image Present on Adapter
2887 Reset Needed: Attempting Port Recovery...
These messages are not necessary for the trace event log, which is
primarily for discovery.
Fix by changing log level on these 2 messages to LOG_SLI.
Link: https://lore.kernel.org/r/20210104180240.46824-15-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several errors have occurred where the adapter stops or fails but does not
raise the register values for the driver to detect failure. Thus driver is
unaware of the failure. The failure typically results in I/O timeouts, the
I/O timeout handler failing (after several seconds), and the error handler
escalating recovery policy and resulting in more errors. Eventually, the
driver is in a position where things have spiraled and it can't do recovery
because other recovery ops are still outstanding and it becomes unusable.
Resolve the situation by having the I/O timeout handler (actually a els,
SCSI I/O, NVMe ls, or NVMe I/O timeout), in addition to aborting the I/O,
perform a mailbox command and look for a response from the hardware. If
the mailbox command fails, it will mark the adapter offline and then invoke
the adapter reset handler to clean up.
The new I/O timeout test will be limited to a test every 5s. If there are
multiple I/O timeouts concurrently, only the 1st I/O timeout will generate
the mailbox command. Further testing will only occur once a timeout occurs
after a 5s delay from the last mailbox command has expired.
Link: https://lore.kernel.org/r/20210104180240.46824-14-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When lpfc is running in NVMET mode and supports the NVME-1 addendum
changes, a LIP on a bound NVME Initiator or lipping the lpfc NVMET's link
resulted in an Oops in lpfc_nvmet_host_release.
The fix requires lpfc NVMET to maintain an additional reference on any node
structure that acts as the hosthandle for the NVMET transport. This
reference get is a one-time addition, is taken prior to the upcall of an
unsolicited LS_REQ, and is released when the NVMET transport releases the
hosthandle during the host_release downcall.
Link: https://lore.kernel.org/r/20210104180240.46824-13-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When with testing with large numbers of npiv vports and link bounces, the
driver is flooding the messages file, even with log_verbose = 0.
The new LOG_TRACE_EVENT messages are still generating events to the
messages files.
Fix by converting the vport create msg from LOG_TRACE_EVENT to LOG_VPORT.
Link: https://lore.kernel.org/r/20210104180240.46824-12-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a mailbox command times out, the SLI port is deemed in error and the
port is reset. The HBA cleanup is not returning I/Os to the NVMe layer
before the port is unregistered. This is due to the HBA being marked
offline (!SLI_ACTIVE) and cleanup being done by the mailbox timeout handler
rather than an general adapter reset routine. The mailbox timeout handler
mailbox handler only cleaned up SCSI I/Os.
Fix by reworking the mailbox handler to:
- After handling the mailbox error, detect the board is already in
failure (may be due to another error), and leave cleanup to the
other handler.
- If the mailbox command timeout is initial detector of the port error,
continue with the board cleanup and marking the adapter offline
(!SLI_ACTIVE). Remove the SCSI-only I/O cleanup routine. The generic
reset adapter routine that is subsequently invoked, will clean up the
I/Os.
- Have the reset adapter routine flush all NVMe and SCSI I/Os if the
adapter has been marked failed (!SLI_ACTIVE).
- Rework the NVMe I/O terminate routine to take a status code to fail the
I/O with and update so that cleaned up I/O calls the wqe completion
routine. Currently it is bypassing the wqe cleanup and calling the NVMe
I/O completion directly. The wqe completion routine will take care of
data structure and node cleanup then call the NVMe I/O completion
handler.
Link: https://lore.kernel.org/r/20210104180240.46824-11-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Target reset is failed by the target as an invalid command.
The Target Reset TMF has been obsoleted in T10 for a while, but continues
to be used. On (newer) devices, the TMF is rejected causing the reset
handler to escalate to adapter resets.
Fix by having Target Reset TMF rejections be translated into a LOGO and
re-PLOGI with the target device. This provides the same semantic action
(although, if the device also supports nvme traffic, it will terminate nvme
traffic as well - but it's still recoverable).
Link: https://lore.kernel.org/r/20210104180240.46824-10-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A successful task mgmt command is logging errors, making it look like
problems were encountered. This is due to log messages for the
device/target and bus reset handlers having the LOG_TRACE_EVENT flag set.
Fix by adjusting the event flag such that the call to the logging routine
only receives a LOG_TRACE_EVENT if a prior call actually failed.
Link: https://lore.kernel.org/r/20210104180240.46824-9-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the lpfc offline routine, called for various reasons such as sysfs
attribute, driver unload, or port error, the driver is calling
__lpfc_cpuhp_remove() to destroy the hot plug data. If the offline routine
is called while the driver is in the process of being unloaded, a request
using lpfc_cpuhp_remove() is also made from lpfc_sli4_hba_unset(). The
cpuhp elements are no longer valid when the second removal request is made.
Fix by only calling the cpuhp removal once when the adapter is in the
process of unloading.
Link: https://lore.kernel.org/r/20210104180240.46824-8-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the port is configured for NVME and has any outstanding IOs when a FW
reset is requesteed, outstanding I/Os are not properly cleaned up. This
causes the fw download request to fail.
Fix by clearing the LPFC_SLI_ACTIVE flag to signify the I/O must be
manually flushed by the driver on port reset.
Link: https://lore.kernel.org/r/20210104180240.46824-7-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When lpfc generates a GEN_REQUEST wqe for the nvme LS (such as Create
Association), the timeout is set to R_A_TOV without regard to the timeout
value supplied by the nvme-fc transport. The driver should be setting the
timeout to the value passed into the routine. Additionally the caller
should be setting the timeout value to the value in the ls request set by
the nvme transport. Instead, it unconditionally is setting it to a driver
defined value. So the driver actually overrode the value twice.
Fix by using the timeout provided to the routine, and for the caller, set
the timeout to the ls request timeout value.
Link: https://lore.kernel.org/r/20210104180240.46824-6-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver's management of the fabric controller (aka pseudo-scsi
initiator) node in SLI3 mode is causing this crash. The crash occurs
because of a node reference imbalance that frees the fabric controller node
while devloss is outstanding from the SCSI transport. This is triggered by
an odd behavior where the switch reacts to a rejected RDP request with a
PLOGI and nothing else, not even a LOGO. The driver ACKS the PLOGI and
after successfully registering the RPI, incorrectly registers the fabric
controller node because it has the NLP_FC4_FCP flag still set from the
fabric controller PRLI. If a LIP is issued, the driver attempts to cleanup
on Link Up and ends up executing too many puts.
Fix by detecting the fabric node type and clearing out the nodes internal
flags that triggered a SCSI transport registration and subsequence dev_loss
event. The driver cannot count on any persistence from fabric controller
nodes.
Link: https://lore.kernel.org/r/20210104180240.46824-5-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Testing with target ports coming and going, the driver eventually reached a
state where it no longer discovered the target. When the driver has issued
a PRLI and receives a PRLI from the target, it is not properly updating the
node's initiator/target role flags. Thus, when a subsequent RSCN is
received for a target loss, the driver mis-identifies the target as an
initiator and does not initiate LUN scanning.
Fix by always refreshing the ndlp with the latest PRLI state information
whenever a PRLI is processed. Also clear the ndlp flags when processing a
PLOGI so that there is no carry over through a re-login.
Link: https://lore.kernel.org/r/20210104180240.46824-4-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A very long time ago, there was a feature: auto sli mode. It gave the user
the ability to auto select the SLI mode (SLI2 or SLI3) to run the port in,
or even force SLI2 mode if configured. Because of the convoluted logic,
the CONFIG_PORT mbox command ends up being called 2 or 3 times. It should
have been called only once. Additionally, the driver no longer supports
SLI-2, so only SLI-3 mode should be allowed.
The following changes were made:
- Force module parameter to SLI3 only.
- Rip out redundant CONFIG_PORT mbox commands.
- Force CONFIG_PORT mbox command to be in beginning of enable ISR routine.
- Added changes for offline to online behavior
Link: https://lore.kernel.org/r/20210104180240.46824-3-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under some pt2pt situations, the other end of the link may issue a LOGO
after successfully completing PLOGI and assigning addresses to the port.
Thus the driver may attempt a new PLOGI to re-create the login, but the
LOGO handling cleared the address back to 0. Once this happens, the other
end, which may be address 0, gets all confused and this cannot be resolved
without an administrative action to bounce the link.
Fix by assuming that address assignment only occurs on the 1st PLOGI after
link up, and regardless of login state, the address assignment sticks. The
FC standards aren't particularly clear in this situation (it only describes
initial PLOGI), but there is nothing that contradicts this and behaviors on
the devices tested appears to conform to the understanding.
Thus, don't reset the port address to 0 as part of LOGO handling. Port
addresses will only reset on link down.
Link: https://lore.kernel.org/r/20210104180240.46824-2-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
smatch correctly called out a logic error with accessing a pointer after
checking it for null:
drivers/scsi/lpfc/lpfc_els.c:2043 lpfc_cmpl_els_plogi()
error: we previously assumed 'ndlp' could be null (see line 1942)
Adjust the exit point to avoid the trace printf ndlp reference. A trace
entry was already generated when the ndlp was checked for null.
Link: https://lore.kernel.org/r/20201130181226.16675-1-james.smart@broadcom.com
Fixes: 4430f7fd09 ("scsi: lpfc: Rework locations of ndlp reference taking")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drivers should do only device-specific jobs. But in general, drivers using
legacy PCI PM framework for .suspend()/.resume() have to manage many PCI
PM-related tasks themselves which can be done by PCI Core itself. This
brings extra load on the driver and it directly calls PCI helper functions
to handle them.
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. Also, remove
unnecessary calls to the PCI Helper functions along with the legacy
.suspend & .resume bindings.
Link: https://lore.kernel.org/r/20201102164730.324035-18-vaibhavgupta40@gmail.com
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove vport variable that is assigned but not used in
lpfc_sli4_abts_err_handler().
Link: https://lore.kernel.org/r/20201119203407.121913-1-james.smart@broadcom.com
Fixes: e7dab164a9 ("scsi: lpfc: Fix scheduling call while in softirq context in lpfc_unreg_rpi")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_nvmet_prep_abort_wqe() needs to be declared static.
Link: https://lore.kernel.org/r/20201119203316.121725-1-james.smart@broadcom.com
Fixes: db7531d2b3 ("scsi: lpfc: Convert abort handling to SLI-3 and SLI-4 handlers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove set but not used variable shost in lpfc_dev_loss_tmo_handler().
Link: https://lore.kernel.org/r/20201119203353.121866-1-james.smart@broadcom.com
Fixes: 52edb2caf6 ("scsi: lpfc: Remove ndlp when a PLOGI/ADISC/PRLI/REG_RPI ultimately fails")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove local variables that are set but not used.
Link: https://lore.kernel.org/r/20201119203340.121819-1-james.smart@broadcom.com
Fixes: c6adba1501 ("scsi: lpfc: Rework remote port lock handling")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Function needs to be declared as static.
Link: https://lore.kernel.org/r/20201119203328.121772-1-james.smart@broadcom.com
Fixes: 8aaa7bcf07 ("scsi: lpfc: Add FDMI Vendor MIB support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently there is an error return path that neglects to free the
allocation for lcb_context. Fix this by adding a new error free exit path
that kfree's lcb_context before returning. Use this new kfree exit path in
another exit error path that also kfree's the same object, allowing a line
of code to be removed.
Link: https://lore.kernel.org/r/20201118141314.462471-1-colin.king@canonical.com
Fixes: 4430f7fd09 ("scsi: lpfc: Rework locations of ndlp reference taking")
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Resource leak")
Currently there is a null check on the pointer ndlp that exits via error
path issue_ct_rsp_exit followed by another null check on the same pointer
that is almost identical to the previous null check stanza and yet can
never can be reached because the previous check exited via
issue_ct_rsp_exit. This is deadcode and can be removed.
Link: https://lore.kernel.org/r/20201118133744.461385-1-colin.king@canonical.com
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Logically dead code")
There is a null check on pointer lpfc_cmd after the pointer has been
dereferenced when pointers rdata and ndlp are initialized at the start of
the function. Fix this by only assigning rdata and ndlp after the pointer
lpfc_cmd has been null checked.
Link: https://lore.kernel.org/r/20201118131345.460631-1-colin.king@canonical.com
Fixes: 96e209be6e ("scsi: lpfc: Convert SCSI I/O completions to SLI-3 and SLI-4 handlers")
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Dereference before null check")
Update Copyright in files changed by the 12.8.0.6 patch set to 2020
Link: https://lore.kernel.org/r/20201115192646.12977-18-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.8.0.6
Link: https://lore.kernel.org/r/20201115192646.12977-17-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch reworks the abort interfaces such that SLI-3 retains the
iocb-based formatting and completions and SLI-4 now uses native WQEs and
completion routines.
The following changes are made:
- The code is refactored from a confusing 2 routine sequence of
xx_abort_iotag_issue(), which creates/formats and abort cmd, and
xx_issue_abort_tag(), which then issues and handles the completion of
the abort cmd - into a single interface of xx_issue_abort_iotag(). The
new interface will determine whether SLI-3 or SLI-4 and then call the
appropriate handler. A completion handler can now be specified to
address the differences in completion handling. Note: original code is
all iocb based, with SLI-4 converting to SLI-3 for the SCSI/ELS path,
and NVMe natively using wqes.
- The SLI-3 side is refactored:
The older iocb-base lpfc_sli_issue_abort_iotag() routine is combined
with the logic of lpfc_sli_abort_iotag_issue() as well as the
iocb-specific code in lpfc_abort_handler() and lpfc_sli_abort_iocb() to
create the new single SLI-3 abort routine that formats and issues the
iocb.
- The SLI-4 side is refactored and added to:
The native WQE abort code in NVMe is moved to the new SLI-4
issue_abort_iotag() routine. Items in SCSI that set fields not set by
NVMe is migrated into the new routine. Thus the routine supports NVMe
and SCSI initiators. The nvmet block (target) formats the abort slightly
different (like the old NVMe initiator) thus it has its own prep routine
stolen from NVMe initiator and it retains the current code it has for
issuing the WQE (does not use the commonized routine the initiators
do). SLI-4 completion handlers were also added.
- lpfc_abort_handler now becomes a wrapper that determines whether
SLI-3 or SLI-4 and calls the proper abort handler.
Link: https://lore.kernel.org/r/20201115192646.12977-16-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current driver implementation uses SLI-4 WQE to iocb conversion before
calling the cmpl callback function.
Rework the FCP I/O completion path to utilize the SLI-4 WQE.
This patch converts the SCSI I/O completion paths from the iocb-centric
interfaces to the routines are native for whether I/Os are iocb-based
(SLI-3) or WQE-based (SLI-4).
Most existing routines were iocb-based, so this creates a lot of SLI-4
specific routines to provide the functionality.
Link: https://lore.kernel.org/r/20201115192646.12977-15-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch converts the SCSI I/O path from the iocb-centric interfaces to
the common I/O submission path which supports native SLI-4 WQEs.
A wrapper routine is put in place to distinguish SLI-3 from SLI. If SLI-3,
the same iocb-centric paths are used, perhaps with refactored code that is
explicitly for SLI-3. For SLI-4, any iocb-related formatting is replaced
by wqe-based formatting, although much of that is addressed by the common
wqe templates in the SLI-4 path.
Link: https://lore.kernel.org/r/20201115192646.12977-14-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To set up common use by the SCSI and NVMe I/O paths, create a new routine
that issues FCP I/O commands which can be used by either protocol. The new
routine addresses SLI-3 vs SLI-4 differences within its implementation.
Replace the (SLI-3 centric) iocb routine in the SCSI path with this new
WQE-centric common routine.
Link: https://lore.kernel.org/r/20201115192646.12977-13-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently using SLI-4 WQE templates only for NVMe. Refactor
the template and the placement of the service routine so that it can be
used by both SCSI and NVMe.
Link: https://lore.kernel.org/r/20201115192646.12977-12-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation of reworking the driver to use a native SLI-4 WQE interface
for the SCSI and NVMe I/O paths, start by commonizing the WQE exchange type
and command type attributes.
While adjusting these options also noted the variance in the pbde field.
Fix this by setting templates to 0 and in NVMe, which explicitly uses this
option, setting the value.
Link: https://lore.kernel.org/r/20201115192646.12977-11-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While testing initiator-side cable swaps with NPIV, oops occur. The
reference counts for the Fabric nodes on the NPIV vports isn't balanced,
resulting in premature node removal.
The following fixes were made:
- Removed the FC_LBIT check in lpfc_linkup_port. This removed the special
case for vports that didn't have them clean up just like the physical
port.
- Removed the unreg_rpi call in lpfc_cleanup_node. In this section, the
node is being removed in the context of a reference count release and a
mailbox command can't be issued at this point.
- Remove special case handling in the default mailbox completion handler
that allowed the skipping of a node reference. Now, reference counting
always requires the removal of the reference.
- Move the location of the DEVICE_RM event is done during LOGO handling as
the driver has additional work to do on the ndlp before puts/releases
can be performed.
Link: https://lore.kernel.org/r/20201115192646.12977-10-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While testing NPIV and link bounces, the vport would not show a fabric node
for the F_Port, would not transition into NPR state during a link fault, or
leave the FDMI node untouched during error injection. Cause for this was
determined to be an inconsistent manner in which F_Port, Nameserver, and
FDMI controller nodes were created and linked. In some cases, the nodes
would never be unregistered from the transport, leaving references
active. In other cases, the fabric nodes may register with the transport
multiple times while still registered.
The following changes were made:
- Fix the FDISC issue routine, which starts vport (re)creation, to mark
the F_Port as a fabric node (NLP_FABRIC) and allow the F_Port node to
fully be created and show up in the node list.
- When remote ports are cleaned up on vport termination, cleanup the
nameserver and FDMI controller nodes on the vport so they unregister
from the transport.
- On link bounces, don't exclude the NPIV Fabric remote ports from
transitioning to the NPR state, allowing them to avoid re-registration
if already registered.
Link: https://lore.kernel.org/r/20201115192646.12977-9-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a target swap happens, under certain conditions the node sends a
LOGO. The unsolicited ELS logic responds with a reject. The logic may
allocate a new node to handle this. Afterward, the new nodes are dropped
incorrectly leaving them in a mis-matched state and refcounting causes a
use-after-free situation leading to a crash.
It is also possible that the unsolicited els handling finds a node which is
in an UNUSED state. The handling moves these nodes to NPR state with a
refcount of 1. Although the end of the discovery logic assumes a final put
will free such a node, there are codes paths which could increment the
reference count, thus the node is in NPR state and not released.
Eventually this mismatch in state and refcount leads to premature release
of the node causing a crash.
Fix by always using the discovery engine DEVICE RM event to decrement and
release the nodes (rather than explicit code that tried to do it before).
This will take care of moving the node to the UNUSED state and then removes
the final ref count. If there is a trigger to reuse this node, the
transition from the UNUSED state clearly indicates that the initial
reference is then incremented and use can continue.
Link: https://lore.kernel.org/r/20201115192646.12977-8-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a PLOGI/ADISC/PRLI/REG_RPI fails, the node remains in the nodelist in
that state. Although the driver now frees a node when the ref count goes
to zero, in this case the ref cnt doesn't reach zero because there isn't a
mechanism to release the final reference. Discovery just stops.
Fix by calling the node discovery state machine DEVICE_RM event whenever
one of these commands fail. This will remove the final reference count and
trigger node release.
Link: https://lore.kernel.org/r/20201115192646.12977-7-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the discovery layers within the driver use the SCSI midlayer
host_lock to access node-specific structures. This can contend with the I/O
path and is too coarse of a lock.
Rework the driver so that it uses a lock specific to the remote port node
structure when accessing the structure contents. A few of the changes
brought out spots were some slightly reorganized routines worked better.
Link: https://lore.kernel.org/r/20201115192646.12977-6-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to bug history and code review, the node reference counting approach in
the driver isn't implemented consistently with how the scsi and nvme
transport perform registrations and unregistrations and their callbacks.
This resulted in many bad/stale node pointers.
Reword the driver so that reference handling is performed as follows:
- The initial node reference is taken on structure allocation
- Take a reference on any add/register call to the transport
- Remove a reference on any delete/unregister call to the transport
- After the node has fully removed from both the SCSI and NVMEe transports
(dev_loss_callbacks have called back) call the discovery engine
DEVICE_RM event which will remove the final reference and release the
node structure.
- Alter dev_loss handling when a vport or base port is unloading.
- Remove the put_node handling - no longer needed.
- Rewrite the vport_delete handling on reference counts. Part of this
effort was driven from the FDISC not registering with the transport and
disrupting the model for node reference counting.
- Deleted lpfc_nlp_remove. Pushed it's remaining ops into
lpfc_nlp_release.
- Several other small code cleanups.
Link: https://lore.kernel.org/r/20201115192646.12977-5-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc driver is calling get_device and put_device on scsi_fc_transport
device structure. When this code was removed, the driver triggered an oops
in "scsi_is_host_dev" when the first SCSI target was unregistered from the
transport.
The reason the calls were necessary is that the driver is calling
scsi_remove_host too early, before the target rports are unregistered and
the scsi devices disconnected from the scsi_host. The fc_host was torn
down during fc_remove_host.
Fix by moving the lpfc_pci_remove_one_s3/s4 calls to scsi_remove_host to
after the nodes are cleaned up. Remove the get_device and put_device calls
and the supporting code.
Link: https://lore.kernel.org/r/20201115192646.12977-4-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that the driver has gone to a normal ref interface (with no odd logic)
the discovery logic needs to be updated to reworked so that it properly
takes references when it should and give them up when it should.
Rework the driver for the following get/put model:
- Move gets to just before an I/O is issued. Add gets for places where an
I/O was issued without one.
- Ensure that failures from lpfc_nlp_get() are handled by the driver.
- Check and fix the placement of lpfc_nlp_puts relative to io completions.
Note: some of these paths may not release the reference on the exact io
completion as the reference is held as the code takes another step in
the discovery thread and which may cause another io to be issued.
- Rearrange some code for error processing and calling lpfc_nlp_put.
- Fix some places of incorrect reference freeing that was causing the
premature releasing of the structure.
- Nvmet plogi handling performs unreg_rpi's. The reference counts were
unbalanced resulting in premature node removal. In some cases this
caused loss of node discovery. Corrected the reftaking around nvmet
plogis.
Nodes that experience devloss now get released from the node list now that
there is a proper reference taking.
Link: https://lore.kernel.org/r/20201115192646.12977-3-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a remote port is disconnected and disappears, its node structure
(ndlp) stays allocated and on a vport node list. While on the list it can
be matched, thus requires validation checks on state to be added in
numerous code paths. If the node comes back, its possible for there to be
multiple node structures for the same device on the vport node list. There
is no reason to keep the node structure around after it is no longer in
existence, and the current implementation creates problems for itself
(multiple nodes) and lots of unnecessary code for state validation.
Additionally, the reference taking on the node structure didn't follow the
normal model used by the kernel kref api. It included lots of odd logic to
match state with reference count. The combination of this odd logic plus
the way it was implicitly used in the discovery engine made its reference
taking implementation suspect and extremely hard to follow.
Change the driver such that the reference taking routines are now normal
ref increments/decrements and callout on refcount=0.
With this in place, the rework can be done such that the node structure is
fully removed and deallocated when the remote port no longer exists and all
references are removed. This removal logic, and the basic ref counting are
intrically tied, thus in a single patch.
Link: https://lore.kernel.org/r/20201115192646.12977-2-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvmet.c:386: warning: Function parameter or member 'ctx_buf' not described in 'lpfc_nvmet_ctxbuf_post'
drivers/scsi/lpfc/lpfc_nvmet.c:386: warning: Excess function parameter 'ctxp' description in 'lpfc_nvmet_ctxbuf_post'
drivers/scsi/lpfc/lpfc_nvmet.c:386: warning: Excess function parameter 'mp' description in 'lpfc_nvmet_ctxbuf_post'
drivers/scsi/lpfc/lpfc_nvmet.c:1310: warning: Function parameter or member 'targetport' not described in 'lpfc_nvmet_ls_req'
drivers/scsi/lpfc/lpfc_nvmet.c:1310: warning: Function parameter or member 'hosthandle' not described in 'lpfc_nvmet_ls_req'
drivers/scsi/lpfc/lpfc_nvmet.c:1310: warning: Function parameter or member 'pnvme_lsreq' not described in 'lpfc_nvmet_ls_req'
drivers/scsi/lpfc/lpfc_nvmet.c:1350: warning: Function parameter or member 'hosthandle' not described in 'lpfc_nvmet_ls_abort'
drivers/scsi/lpfc/lpfc_nvmet.c:1350: warning: Function parameter or member 'pnvme_lsreq' not described in 'lpfc_nvmet_ls_abort'
drivers/scsi/lpfc/lpfc_nvmet.c:3607: warning: Function parameter or member 'phba' not described in 'lpfc_nvmet_invalidate_host'
drivers/scsi/lpfc/lpfc_nvmet.c:3607: warning: Function parameter or member 'ndlp' not described in 'lpfc_nvmet_invalidate_host'
Link: https://lore.kernel.org/r/20201102142359.561122-15-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvme.c: In function ‘lpfc_nvme_ls_abort’:
drivers/scsi/lpfc/lpfc_nvme.c:943:19: warning: variable ‘phba’ set but not used [-Wunused-but-set-variable]
drivers/scsi/lpfc/lpfc_nvme.c:256: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_create_queue'
drivers/scsi/lpfc/lpfc_nvme.c:804: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:804: warning: Excess function parameter 'nvme_rport' description in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:1312: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1312: warning: Excess function parameter 'lpfcn_cmd' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1416: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1416: warning: Excess function parameter 'lpfcn_cmd' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1594: warning: bad line: indicated in @lpfc_nvme_rport.
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1852: warning: Function parameter or member 'abts_cmpl' not described in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1852: warning: Excess function parameter 'rspiocb' description in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:2089: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2089: warning: Function parameter or member 'idx' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2089: warning: Function parameter or member 'expedite' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2193: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_create_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2326: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2326: warning: Excess function parameter 'pnvme' description in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2544: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_rescan_port'
drivers/scsi/lpfc/lpfc_nvme.c:2544: warning: Function parameter or member 'ndlp' not described in 'lpfc_nvme_rescan_port'
Link: https://lore.kernel.org/r/20201102142359.561122-13-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvme.c: In function ‘lpfc_nvme_ls_abort’:
drivers/scsi/lpfc/lpfc_nvme.c:943:19: warning: variable ‘phba’ set but not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20201102142359.561122-11-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_bsg.c:917: warning: Function parameter or member 'phba' not described in 'lpfc_bsg_ct_unsol_event'
drivers/scsi/lpfc/lpfc_bsg.c:917: warning: Function parameter or member 'pring' not described in 'lpfc_bsg_ct_unsol_event'
drivers/scsi/lpfc/lpfc_bsg.c:1484: warning: Function parameter or member 'cmp' not described in 'lpfc_issue_ct_rsp'
drivers/scsi/lpfc/lpfc_bsg.c:3900: warning: Function parameter or member 'job' not described in 'lpfc_bsg_sli_cfg_read_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:3900: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_sli_cfg_read_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:3900: warning: Excess function parameter 'mb' description in 'lpfc_bsg_sli_cfg_read_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:3900: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_sli_cfg_read_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Function parameter or member 'job' not described in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Function parameter or member 'nemb_tp' not described in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Excess function parameter 'mb' description in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4088: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_sli_cfg_write_cmd_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4254: warning: Function parameter or member 'job' not described in 'lpfc_bsg_handle_sli_cfg_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4254: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_handle_sli_cfg_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4254: warning: Excess function parameter 'mb' description in 'lpfc_bsg_handle_sli_cfg_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4254: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_handle_sli_cfg_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4403: warning: Function parameter or member 'job' not described in 'lpfc_bsg_read_ebuf_get'
drivers/scsi/lpfc/lpfc_bsg.c:4403: warning: Excess function parameter 'dmabuf' description in 'lpfc_bsg_read_ebuf_get'
drivers/scsi/lpfc/lpfc_bsg.c:4474: warning: Function parameter or member 'job' not described in 'lpfc_bsg_write_ebuf_set'
drivers/scsi/lpfc/lpfc_bsg.c:4600: warning: Function parameter or member 'job' not described in 'lpfc_bsg_handle_sli_cfg_ebuf'
drivers/scsi/lpfc/lpfc_bsg.c:4600: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_handle_sli_cfg_ebuf'
drivers/scsi/lpfc/lpfc_bsg.c:4600: warning: Excess function parameter 'mb' description in 'lpfc_bsg_handle_sli_cfg_ebuf'
drivers/scsi/lpfc/lpfc_bsg.c:4600: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_handle_sli_cfg_ebuf'
drivers/scsi/lpfc/lpfc_bsg.c:4645: warning: Function parameter or member 'job' not described in 'lpfc_bsg_handle_sli_cfg_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4645: warning: Function parameter or member 'dmabuf' not described in 'lpfc_bsg_handle_sli_cfg_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4645: warning: Excess function parameter 'mb' description in 'lpfc_bsg_handle_sli_cfg_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4645: warning: Excess function parameter 'dmabuff' description in 'lpfc_bsg_handle_sli_cfg_ext'
drivers/scsi/lpfc/lpfc_bsg.c:4723: warning: Function parameter or member 'job' not described in 'lpfc_bsg_issue_mbox'
drivers/scsi/lpfc/lpfc_bsg.c:4723: warning: Excess function parameter 'mb' description in 'lpfc_bsg_issue_mbox'
Link: https://lore.kernel.org/r/20201102142359.561122-8-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_debugfs.c:4204: warning: Function parameter or member 'len' not described in 'lpfc_idiag_queacc_read_qe'
drivers/scsi/lpfc/lpfc_debugfs.c:4781: warning: Function parameter or member 'ctlregid' not described in 'lpfc_idiag_ctlacc_read_reg'
drivers/scsi/lpfc/lpfc_debugfs.c:4781: warning: Excess function parameter 'drbregid' description in 'lpfc_idiag_ctlacc_read_reg'
Link: https://lore.kernel.org/r/20201102142359.561122-7-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
from drivers/scsi/lpfc/lpfc_attr.c:26:
inlined from ‘lpfc_stat_data_ctrl_store’ at drivers/scsi/lpfc/lpfc_attr.c:4165:3:
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Function parameter or member 'attr' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Function parameter or member 'default' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Function parameter or member 'minval' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Function parameter or member 'maxval' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Excess function parameter 'phba' description in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2537: warning: Excess function parameter 'val' description in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2792: warning: Function parameter or member 'dev' not described in 'lpfc_soft_wwpn_store'
drivers/scsi/lpfc/lpfc_attr.c:2886: warning: Function parameter or member 'dev' not described in 'lpfc_soft_wwnn_store'
drivers/scsi/lpfc/lpfc_attr.c:2886: warning: Function parameter or member 'attr' not described in 'lpfc_soft_wwnn_store'
drivers/scsi/lpfc/lpfc_attr.c:2886: warning: Excess function parameter 'cdev' description in 'lpfc_soft_wwnn_store'
drivers/scsi/lpfc/lpfc_attr.c:3224: warning: Function parameter or member 'vpt_wwpn' not described in 'lpfc_oas_lun_state_set'
drivers/scsi/lpfc/lpfc_attr.c:3224: warning: Function parameter or member 'tgt_wwpn' not described in 'lpfc_oas_lun_state_set'
drivers/scsi/lpfc/lpfc_attr.c:3224: warning: Function parameter or member 'pri' not described in 'lpfc_oas_lun_state_set'
drivers/scsi/lpfc/lpfc_attr.c:3224: warning: Excess function parameter 'ndlp' description in 'lpfc_oas_lun_state_set'
drivers/scsi/lpfc/lpfc_attr.c:3264: warning: Function parameter or member 'lun_pri' not described in 'lpfc_oas_lun_get_next'
drivers/scsi/lpfc/lpfc_attr.c:3302: warning: Function parameter or member 'pri' not described in 'lpfc_oas_lun_state_change'
drivers/scsi/lpfc/lpfc_attr.c:3376: warning: Function parameter or member 'count' not described in 'lpfc_oas_lun_store'
drivers/scsi/lpfc/lpfc_attr.c:3835: warning: Function parameter or member 'vport' not described in 'lpfc_tgt_queue_depth_set'
drivers/scsi/lpfc/lpfc_attr.c:3835: warning: Excess function parameter 'phba' description in 'lpfc_tgt_queue_depth_set'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Function parameter or member 'dev' not described in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Function parameter or member 'attr' not described in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Function parameter or member 'buf' not described in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Function parameter or member 'count' not described in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Excess function parameter 'phba' description in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4026: warning: Excess function parameter 'val' description in 'lpfc_topology_store'
drivers/scsi/lpfc/lpfc_attr.c:4148: warning: Function parameter or member 'attr' not described in 'lpfc_stat_data_ctrl_store'
drivers/scsi/lpfc/lpfc_attr.c:4302: warning: Function parameter or member 'attr' not described in 'lpfc_stat_data_ctrl_show'
drivers/scsi/lpfc/lpfc_attr.c:4383: warning: Function parameter or member 'buf' not described in 'sysfs_drvr_stat_data_read'
drivers/scsi/lpfc/lpfc_attr.c:4383: warning: Excess function parameter 'buff' description in 'sysfs_drvr_stat_data_read'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Function parameter or member 'dev' not described in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Function parameter or member 'attr' not described in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Function parameter or member 'buf' not described in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Function parameter or member 'count' not described in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Excess function parameter 'phba' description in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:4476: warning: Excess function parameter 'val' description in 'lpfc_link_speed_store'
drivers/scsi/lpfc/lpfc_attr.c:7117: warning: Function parameter or member 'verbose' not described in 'lpfc_hba_log_verbose_init'
Link: https://lore.kernel.org/r/20201102142359.561122-6-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kernel-doc does not understand this use-case.
Fixes the following W=1 kernel build warning(s):
from drivers/scsi/lpfc/lpfc_attr.c:26:
inlined from ‘lpfc_stat_data_ctrl_store’ at drivers/scsi/lpfc/lpfc_attr.c:4164:3:
drivers/scsi/lpfc/lpfc_attr.c:2315: warning: Excess function parameter 'dev' description in 'lpfc_param_show'
drivers/scsi/lpfc/lpfc_attr.c:2315: warning: Excess function parameter 'buf' description in 'lpfc_param_show'
drivers/scsi/lpfc/lpfc_attr.c:2343: warning: Excess function parameter 'dev' description in 'lpfc_param_hex_show'
drivers/scsi/lpfc/lpfc_attr.c:2343: warning: Excess function parameter 'buf' description in 'lpfc_param_hex_show'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Function parameter or member 'attr' not described in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Function parameter or member 'default' not described in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Function parameter or member 'minval' not described in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Function parameter or member 'maxval' not described in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Excess function parameter 'phba' description in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2377: warning: Excess function parameter 'val' description in 'lpfc_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Function parameter or member 'attr' not described in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Function parameter or member 'default' not described in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Function parameter or member 'minval' not described in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Function parameter or member 'maxval' not described in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Excess function parameter 'phba' description in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2414: warning: Excess function parameter 'val' description in 'lpfc_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2454: warning: Excess function parameter 'dev' description in 'lpfc_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2454: warning: Excess function parameter 'buf' description in 'lpfc_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2454: warning: Excess function parameter 'count' description in 'lpfc_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2478: warning: Excess function parameter 'dev' description in 'lpfc_vport_param_show'
drivers/scsi/lpfc/lpfc_attr.c:2478: warning: Excess function parameter 'buf' description in 'lpfc_vport_param_show'
drivers/scsi/lpfc/lpfc_attr.c:2503: warning: Excess function parameter 'dev' description in 'lpfc_vport_param_hex_show'
drivers/scsi/lpfc/lpfc_attr.c:2503: warning: Excess function parameter 'buf' description in 'lpfc_vport_param_hex_show'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Function parameter or member 'attr' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Function parameter or member 'default' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Function parameter or member 'minval' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Function parameter or member 'maxval' not described in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Excess function parameter 'phba' description in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2536: warning: Excess function parameter 'val' description in 'lpfc_vport_param_init'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Function parameter or member 'attr' not described in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Function parameter or member 'default' not described in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Function parameter or member 'minval' not described in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Function parameter or member 'maxval' not described in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Excess function parameter 'phba' description in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2572: warning: Excess function parameter 'val' description in 'lpfc_vport_param_set'
drivers/scsi/lpfc/lpfc_attr.c:2607: warning: Function parameter or member 'attr' not described in 'lpfc_vport_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2607: warning: Excess function parameter 'cdev' description in 'lpfc_vport_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2607: warning: Excess function parameter 'buf' description in 'lpfc_vport_param_store'
drivers/scsi/lpfc/lpfc_attr.c:2607: warning: Excess function parameter 'count' description in 'lpfc_vport_param_store'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Function parameter or member 'field' not described in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Function parameter or member 'format_string' not described in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Function parameter or member 'sz' not described in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Function parameter or member 'cast' not described in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Excess function parameter 'cdev' description in 'lpfc_rport_show_function'
drivers/scsi/lpfc/lpfc_attr.c:7081: warning: Excess function parameter 'buf' description in 'lpfc_rport_show_function'
Link: https://lore.kernel.org/r/20201102142359.561122-5-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_scsi.c:331: warning: Function parameter or member 'num_to_alloc' not described in 'lpfc_new_scsi_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:331: warning: Excess function parameter 'num_to_allocate' description in 'lpfc_new_scsi_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:507: warning: Function parameter or member 'idx' not described in 'lpfc_sli4_io_xri_aborted'
drivers/scsi/lpfc/lpfc_scsi.c:593: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_scsi_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:593: warning: Function parameter or member 'cmnd' not described in 'lpfc_get_scsi_buf_s3'
drivers/scsi/lpfc/lpfc_scsi.c:632: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_scsi_buf_s4'
drivers/scsi/lpfc/lpfc_scsi.c:632: warning: Function parameter or member 'cmnd' not described in 'lpfc_get_scsi_buf_s4'
drivers/scsi/lpfc/lpfc_scsi.c:744: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_scsi_buf'
drivers/scsi/lpfc/lpfc_scsi.c:744: warning: Function parameter or member 'cmnd' not described in 'lpfc_get_scsi_buf'
drivers/scsi/lpfc/lpfc_scsi.c:986: warning: Function parameter or member 'new_guard' not described in 'lpfc_bg_err_inject'
drivers/scsi/lpfc/lpfc_scsi.c:1393: warning: Function parameter or member 'txop' not described in 'lpfc_sc_to_bg_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1393: warning: Function parameter or member 'rxop' not described in 'lpfc_sc_to_bg_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1393: warning: Excess function parameter 'txopt' description in 'lpfc_sc_to_bg_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1393: warning: Excess function parameter 'rxopt' description in 'lpfc_sc_to_bg_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1473: warning: Function parameter or member 'txop' not described in 'lpfc_bg_err_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1473: warning: Function parameter or member 'rxop' not described in 'lpfc_bg_err_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1473: warning: Excess function parameter 'txopt' description in 'lpfc_bg_err_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1473: warning: Excess function parameter 'rxopt' description in 'lpfc_bg_err_opcodes'
drivers/scsi/lpfc/lpfc_scsi.c:1565: warning: Function parameter or member 'datasegcnt' not described in 'lpfc_bg_setup_bpl'
drivers/scsi/lpfc/lpfc_scsi.c:1565: warning: Excess function parameter 'datacnt' description in 'lpfc_bg_setup_bpl'
drivers/scsi/lpfc/lpfc_scsi.c:1951: warning: Function parameter or member 'datasegcnt' not described in 'lpfc_bg_setup_sgl'
drivers/scsi/lpfc/lpfc_scsi.c:1951: warning: Function parameter or member 'lpfc_cmd' not described in 'lpfc_bg_setup_sgl'
drivers/scsi/lpfc/lpfc_scsi.c:1951: warning: Excess function parameter 'datacnt' description in 'lpfc_bg_setup_sgl'
drivers/scsi/lpfc/lpfc_scsi.c:2131: warning: Function parameter or member 'lpfc_cmd' not described in 'lpfc_bg_setup_sgl_prot'
drivers/scsi/lpfc/lpfc_scsi.c:4476: warning: Function parameter or member 't' not described in 'lpfc_poll_timeout'
drivers/scsi/lpfc/lpfc_scsi.c:4476: warning: Excess function parameter 'ptr' description in 'lpfc_poll_timeout'
drivers/scsi/lpfc/lpfc_scsi.c:4503: warning: Function parameter or member 'shost' not described in 'lpfc_queuecommand'
drivers/scsi/lpfc/lpfc_scsi.c:4503: warning: Excess function parameter 'done' description in 'lpfc_queuecommand'
drivers/scsi/lpfc/lpfc_scsi.c:5035: warning: Function parameter or member 'cmnd' not described in 'lpfc_send_taskmgmt'
drivers/scsi/lpfc/lpfc_scsi.c:5035: warning: Excess function parameter 'rdata' description in 'lpfc_send_taskmgmt'
drivers/scsi/lpfc/lpfc_scsi.c:5688: warning: Function parameter or member 'phba' not described in 'lpfc_create_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5688: warning: Function parameter or member 'pri' not described in 'lpfc_create_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5688: warning: Excess function parameter 'pha' description in 'lpfc_create_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5730: warning: Function parameter or member 'phba' not described in 'lpfc_delete_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5730: warning: Excess function parameter 'pha' description in 'lpfc_delete_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5762: warning: Function parameter or member 'phba' not described in '__lpfc_get_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5762: warning: Excess function parameter 'pha' description in '__lpfc_get_device_data'
drivers/scsi/lpfc/lpfc_scsi.c:5818: warning: Function parameter or member 'phba' not described in 'lpfc_find_next_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5818: warning: Function parameter or member 'found_lun_pri' not described in 'lpfc_find_next_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5818: warning: Excess function parameter 'pha' description in 'lpfc_find_next_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5909: warning: Function parameter or member 'phba' not described in 'lpfc_enable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5909: warning: Function parameter or member 'pri' not described in 'lpfc_enable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5909: warning: Excess function parameter 'pha' description in 'lpfc_enable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5968: warning: Function parameter or member 'phba' not described in 'lpfc_disable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5968: warning: Function parameter or member 'pri' not described in 'lpfc_disable_oas_lun'
drivers/scsi/lpfc/lpfc_scsi.c:5968: warning: Excess function parameter 'pha' description in 'lpfc_disable_oas_lun'
Link: https://lore.kernel.org/r/20201102142359.561122-4-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.8.0.5
Link: https://lore.kernel.org/r/20201020202719.54726-10-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that MIB support was registered with FDMI, the driver may receive CT
requests for MIB-related commands. At this time, no command is
supported. However, the driver needs to be graceful and reject the CT
request.
This patch adds identification of the requests as well as sending the
reject response.
Link: https://lore.kernel.org/r/20201020202719.54726-9-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Created new attribute lpfc_enable_mi, which by default is enabled.
Add command definition bits for SLI-4 parameters that recognize whether the
adapter has MIB information support and what revision of MIB data. Using
the adapter information, register vendor-specific MIB support with FDMI.
The registration will be done every link up.
During FDMI registration, encountered a couple of errors when reverting to
FDMI rev1. Code needed to exist once reverting. Fixed these.
Link: https://lore.kernel.org/r/20201020202719.54726-8-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver supports arbitrarily large scatter-gather lists and the current
value for max_sectors is limiting.
Change max_sectors to the largest value. This was actually done prior but
it only corrected one template and that template was later removed.
So change the remaining 2 templates. Other areas which hard-set the sectors
value should be inheriting what is in the template.
Link: https://lore.kernel.org/r/20201020202719.54726-7-james.smart@broadcom.com
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During code reviews duplicate code sections were found to determine the WQ
Create version. The duplication was potentially overriding logic that
validated page size.
Link: https://lore.kernel.org/r/20201020202719.54726-6-james.smart@broadcom.com
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 9816ef6ecb ("scsi: lpfc: Use after free in lpfc_rq_buf_free()")
was made to correct a use after free condition in lpfc_rq_buf_free().
Unfortunately, a subsequent patch cut on a tree without the fix
inadvertently reverted the fix.
Put the fix back: Move the freeing of the rqb_entry to after the print
function that references it.
Link: https://lore.kernel.org/r/20201020202719.54726-4-james.smart@broadcom.com
Fixes: 411de511c6 ("scsi: lpfc: Fix RQ empty firmware trap")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following call trace was seen during HBA reset testing:
BUG: scheduling while atomic: swapper/2/0/0x10000100
...
Call Trace:
dump_stack+0x19/0x1b
__schedule_bug+0x64/0x72
__schedule+0x782/0x840
__cond_resched+0x26/0x30
_cond_resched+0x3a/0x50
mempool_alloc+0xa0/0x170
lpfc_unreg_rpi+0x151/0x630 [lpfc]
lpfc_sli_abts_recover_port+0x171/0x190 [lpfc]
lpfc_sli4_abts_err_handler+0xb2/0x1f0 [lpfc]
lpfc_sli4_io_xri_aborted+0x256/0x300 [lpfc]
lpfc_sli4_sp_handle_abort_xri_wcqe.isra.51+0xa3/0x190 [lpfc]
lpfc_sli4_fp_handle_cqe+0x89/0x4d0 [lpfc]
__lpfc_sli4_process_cq+0xdb/0x2e0 [lpfc]
__lpfc_sli4_hba_process_cq+0x41/0x100 [lpfc]
lpfc_cq_poll_hdler+0x1a/0x30 [lpfc]
irq_poll_softirq+0xc7/0x100
__do_softirq+0xf5/0x280
call_softirq+0x1c/0x30
do_softirq+0x65/0xa0
irq_exit+0x105/0x110
do_IRQ+0x56/0xf0
common_interrupt+0x16a/0x16a
With the conversion to blk_io_poll for better interrupt latency in normal
cases, it introduced this code path, executed when I/O aborts or logouts
are seen, which attempts to allocate memory for a mailbox command to be
issued. The allocation is GFP_KERNEL, thus it could attempt to sleep.
Fix by creating a work element that performs the event handling for the
remote port. This will have the mailbox commands and other items performed
in the work element, not the irq. A much better method as the "irq" routine
does not stall while performing all this deep handling code.
Ensure that allocation failures are handled and send LOGO on failure.
Additionally, enlarge the mailbox memory pool to reduce the possibility of
additional allocation in this path.
Link: https://lore.kernel.org/r/20201020202719.54726-3-james.smart@broadcom.com
Fixes: 317aeb83c9 ("scsi: lpfc: Add blk_io_poll support for latency improvment")
Cc: <stable@vger.kernel.org> # v5.9+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following calltrace was seen:
BUG: sleeping function called from invalid context at mm/slab.h:494
...
Call Trace:
dump_stack+0x9a/0xf0
___might_sleep.cold.63+0x13d/0x178
slab_pre_alloc_hook+0x6a/0x90
kmem_cache_alloc_trace+0x3a/0x2d0
lpfc_sli4_nvmet_alloc+0x4c/0x280 [lpfc]
lpfc_post_rq_buffer+0x2e7/0xa60 [lpfc]
lpfc_sli4_hba_setup+0x6b4c/0xa4b0 [lpfc]
lpfc_pci_probe_one_s4.isra.15+0x14f8/0x2280 [lpfc]
lpfc_pci_probe_one+0x260/0x2880 [lpfc]
local_pci_probe+0xd4/0x180
work_for_cpu_fn+0x51/0xa0
process_one_work+0x8f0/0x17b0
worker_thread+0x536/0xb50
kthread+0x30c/0x3d0
ret_from_fork+0x3a/0x50
A prior patch introduced a spin_lock_irqsave(hbalock) in the
lpfc_post_rq_buffer() routine. Call trace is seen as the hbalock is held
with interrupts disabled during a GFP_KERNEL allocation in
lpfc_sli4_nvmet_alloc().
Fix by reordering locking so that hbalock not held when calling
sli4_nvmet_alloc() (aka rqb_buf_list()).
Link: https://lore.kernel.org/r/20201020202719.54726-2-james.smart@broadcom.com
Fixes: 411de511c6 ("scsi: lpfc: Fix RQ empty firmware trap")
Cc: <stable@vger.kernel.org> # v4.17+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, qla2xxx, tcmu,
ibmvfc, lpfc, smartpqi, hisi_sas, qedi, qedf, mpt3sas) and minor bug
fixes. There are only three core changes: adding sense codes,
cleaning up noretry and adding an option for limitless retries.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX4YulyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishaZDAQCT7rwG
UEZYHgYkU9EX9ERVBQM0SW4mLrxf3g3P5ioJsAEAtkclCM4QsIOP+MIPjIa0EyUY
khu0kcrmeFR2YwA8zhw=
=4w4S
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"The usual driver updates (ufs, qla2xxx, tcmu, ibmvfc, lpfc, smartpqi,
hisi_sas, qedi, qedf, mpt3sas) and minor bug fixes.
There are only three core changes: adding sense codes, cleaning up
noretry and adding an option for limitless retries"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (226 commits)
scsi: hisi_sas: Recover PHY state according to the status before reset
scsi: hisi_sas: Filter out new PHY up events during suspend
scsi: hisi_sas: Add device link between SCSI devices and hisi_hba
scsi: hisi_sas: Add check for methods _PS0 and _PR0
scsi: hisi_sas: Add controller runtime PM support for v3 hw
scsi: hisi_sas: Switch to new framework to support suspend and resume
scsi: hisi_sas: Use hisi_hba->cq_nvecs for calling calling synchronize_irq()
scsi: qedf: Remove redundant assignment to variable 'rc'
scsi: lpfc: Remove unneeded variable 'status' in lpfc_fcp_cpu_map_store()
scsi: snic: Convert to use DEFINE_SEQ_ATTRIBUTE macro
scsi: qla4xxx: Delete unneeded variable 'status' in qla4xxx_process_ddb_changed
scsi: sun_esp: Use module_platform_driver to simplify the code
scsi: sun3x_esp: Use module_platform_driver to simplify the code
scsi: sni_53c710: Use module_platform_driver to simplify the code
scsi: qlogicpti: Use module_platform_driver to simplify the code
scsi: mac_esp: Use module_platform_driver to simplify the code
scsi: jazz_esp: Use module_platform_driver to simplify the code
scsi: mvumi: Fix error return in mvumi_io_attach()
scsi: lpfc: Drop nodelist reference on error in lpfc_gen_req()
scsi: be2iscsi: Fix a theoretical leak in beiscsi_create_eqs()
...
Fixes coccicheck warning:
drivers/scsi/lpfc/lpfc_attr.c:5341:5-11: Unneeded variable: "status". Return "- EINVAL" on line 5342
Link: https://lore.kernel.org/r/20200916022859.349089-1-yebin10@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we fail to issue the iocb in lpfc_gen_req() we need to drop the nodelist
reference.
Link: https://lore.kernel.org/r/20200910084059.138507-1-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Three fixes: one in drivers (lpfc) and two for zoned block devices.
The latter also impinges on the block layer but only to introduce a
new block API for setting the zone model rather than fiddling with the
queue directly in the zoned block driver.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX29mRyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishabnAP48vMYD
/cjyGAJfq/0k/U/t6pRPc5tUm89LOWcOJz0SjwD/YXcQNz7mx8MxnypAV1jbWXR7
iyWkPMYVc4EJh7oTARE=
=SQhI
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three fixes: one in drivers (lpfc) and two for zoned block devices.
The latter also impinges on the block layer but only to introduce a
new block API for setting the zone model rather than fiddling with the
queue directly in the zoned block driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: sd_zbc: Fix ZBC disk initialization
scsi: sd: sd_zbc: Fix handling of host-aware ZBC disks
scsi: lpfc: Fix initial FLOGI failure due to BBSCN not supported
Initial FLOGIs are failing with the following message:
lpfc 0000:13:00.1: 1:(0):0820 FLOGI Failed (x300). BBCredit Not Supported
In a prior patch, the READ_SPARAM command was re-ordered to post after
CONFIG_LINK as the driver is expected to update the driver's copy of the
service parameters for the FLOGI payload. If the bb-credit recovery feature
is enabled, this is fine. But on adapters were bb-credit recovery isn't
enabled, it would cause the FLOGI to fail.
Fix by restoring the original command order (READ_SPARAM before
CONFIG_LINK), and after issuing CONFIG_LINK, detect bb-credit recovery
support and reissuing READ_SPARAM to obtain the updated service parameters
(effectively adding in the fix command order).
[mkp: corrected SHA]
Link: https://lore.kernel.org/r/20200911200147.110826-1-james.smart@broadcom.com
Fixes: 835214f5d5 ("scsi: lpfc: Fix broken Credit Recovery after driver load")
CC: <stable@vger.kernel.org> # v5.7+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This addresses the following gcc warning with "make W=1":
not used [-Wunused-but-set-variable]
struct lpfc_sli4_hdw_queue *qp;
^
Link: https://lore.kernel.org/r/20200909082716.37787-1-yebin10@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
drivers/scsi/lpfc/lpfc_debugfs.c: In function ‘lpfc_debugfs_hdwqstat_data’:
drivers/scsi/lpfc/lpfc_debugfs.c:1699:30: warning: variable ‘qp’ set but
Eleven fixes, mostly in drivers or minor fixes in driver related
infrastructure libraries (target, libfc and libsas). Most of the bugs
fixed only show up under rare circumstances, the exception being the
endianness problem in qla2xxx which is used as a device on some sparc
systems.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX1egVyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishShgAP9McHKn
9T/m2mAjBr8IMZRlD4Y6nC+ToxDdRDsYT6iAOQD/ZO1FajxEcGC4xEtWznvXtqGk
H1Lfr/ta19GSEPqaZ44=
=rDo9
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Eleven fixes, mostly in drivers or minor fixes in driver related
infrastructure libraries (target, libfc and libsas).
Most of the bugs fixed only show up under rare circumstances, the
exception being the endianness problem in qla2xxx which is used as a
device on some sparc systems"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpt3sas: Don't call disable_irq from IRQ poll handler
scsi: megaraid_sas: Don't call disable_irq from process IRQ poll
scsi: target: iscsi: Fix hang in iscsit_access_np() when getting tpg->np_login_sem
scsi: libsas: Set data_dir as DMA_NONE if libata marks qc as NODATA
scsi: target: iscsi: Fix data digest calculation
scsi: lpfc: Update lpfc version to 12.8.0.4
scsi: lpfc: Extend the RDF FPIN Registration descriptor for additional events
scsi: lpfc: Fix FLOGI/PLOGI receive race condition in pt2pt discovery
scsi: lpfc: Fix setting IRQ affinity with an empty CPU mask
scsi: qla2xxx: Fix regression on sparc64
scsi: libfc: Fix for double free()
scsi: pm8001: Fix memleak in pm8001_exec_internal_task_abort
Update lpfc version to 12.8.0.4
Link: https://lore.kernel.org/r/20200828175332.130300-5-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver registers for Link Integrity events only.
This patch adds registration for the following FPIN types:
- Delivery Notifications
- Congestion Notification
- Peer Congestion Notification
Link: https://lore.kernel.org/r/20200828175332.130300-4-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is unable to successfully login with remote device. During pt2pt
login, the driver completes its FLOGI request with the remote device having
WWN precedence. The remote device issues its own (delayed) FLOGI after
accepting the driver's and, upon transmitting the FLOGI, immediately
recognizes it has already processed the driver's FLOGI thus it transitions
to sending a PLOGI before waiting for an ACC to its FLOGI.
In the driver, the FLOGI is received and an ACC sent, followed by the PLOGI
being received and an ACC sent. The issue is that the PLOGI reception
occurs before the response from the adapter from the FLOGI ACC is
received. Processing of the PLOGI sets state flags to perform the REG_RPI
mailbox command and proceed with the rest of discovery on the port. The
same completion routine used by both FLOGI and PLOGI is generic in
nature. One of the things it does is clear flags, and those flags happen to
drive the rest of discovery. So what happened was the PLOGI processing set
the flags, the FLOGI ACC completion cleared them, thus when the PLOGI ACC
completes it doesn't see the flags and stops.
Fix by modifying the generic completion routine to not clear the rest of
discovery flag (NLP_ACC_REGLOGIN) unless the completion is also associated
with performing a mailbox command as part of its handling. For things such
as FLOGI ACC, there isn't a subsequent action to perform with the adapter,
thus there is no mailbox cmd ptr. PLOGI ACC though will perform REG_RPI
upon completion, thus there is a mailbox cmd ptr.
Link: https://lore.kernel.org/r/20200828175332.130300-3-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some systems are reporting the following log message during driver unload
or system shutdown:
ics_rtas_set_affinity: No online cpus in the mask
A prior commit introduced the writing of an empty affinity mask in calls to
irq_set_affinity_hint() when disabling interrupts or when there are no
remaining online CPUs to service an eq interrupt. At least some ppc64
systems are checking whether affinity masks are empty or not.
Do not call irq_set_affinity_hint() with an empty CPU mask.
Fixes: dcaa213679 ("scsi: lpfc: Change default IRQ model on AMD architectures")
Link: https://lore.kernel.org/r/20200828175332.130300-2-james.smart@broadcom.com
Cc: <stable@vger.kernel.org> # v5.5+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the set of patches which arrived too late to stabilise in
-next for the first pull. It's really just an lpfc driver update and
an assortment of minor fixes, all in drivers. The only core update is
to the zone block device driver, which isn't the one most people use.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXza9yiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYyiAQCUJJ8m
vraqyBzjAPWpPsoNZmrvUxciXEDhoLrFo4Nl8wEAoJPVjUd79dXCJHB1Oq+MaeaF
LODgv2bO1F4TCf59F+4=
=+wdb
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the set of patches which arrived too late to stabilise in
-next for the first pull.
It's really just an lpfc driver update and an assortment of minor
fixes, all in drivers. The only core update is to the zone block
device driver, which isn't the one most people use"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Update lpfc version to 12.8.0.3
scsi: lpfc: Fix LUN loss after cable pull
scsi: lpfc: Fix validation of bsg reply lengths
scsi: lpfc: Fix retry of PRLI when status indicates its unsupported
scsi: lpfc: Fix oops when unloading driver while running mds diags
scsi: lpfc: Fix RSCN timeout due to incorrect gidft counter
scsi: lpfc: Fix no message shown for lpfc_hdw_queue out of range value
scsi: lpfc: Fix FCoE speed reporting
scsi: lpfc: Add missing misc_deregister() for lpfc_init()
scsi: lpfc: nvmet: Avoid hang / use-after-free again when destroying targetport
scsi: scsi_transport_sas: Add spaces around binary operator "|"
scsi: sd_zbc: Improve zone revalidation
scsi: libfc: Free skb in fc_disc_gpn_id_resp() for valid cases
scsi: fcoe: Memory leak fix in fcoe_sysfs_fcf_del()
scsi: target: Make iscsit_register_transport() return void
This series consists of the usual driver updates (ufs, qla2xxx, tcmu,
lpfc, hpsa, zfcp, scsi_debug) and minor bug fixes. We also have a
huge docbook fix update like most other subsystems and no major update
to the core (the few non trivial updates are either minor fixes or
removing an unused feature [scsi_sdb_cache]).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXyxq1yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSoAAQChZ4i8
ZqYW3pL33JO3fA8vdjvLuyC489Hj4wzIsl3/bQEAxYyM6BSLvMoLWR2Plq/JmTLm
4W/LDptarpTiDI3NuDc=
=4b0W
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, qla2xxx, tcmu, lpfc,
hpsa, zfcp, scsi_debug) and minor bug fixes.
We also have a huge docbook fix update like most other subsystems and
no major update to the core (the few non trivial updates are either
minor fixes or removing an unused feature [scsi_sdb_cache])"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (307 commits)
scsi: scsi_transport_srp: Sanitize scsi_target_block/unblock sequences
scsi: ufs-mediatek: Apply DELAY_AFTER_LPM quirk to Micron devices
scsi: ufs: Introduce device quirk "DELAY_AFTER_LPM"
scsi: virtio-scsi: Correctly handle the case where all LUNs are unplugged
scsi: scsi_debug: Implement tur_ms_to_ready parameter
scsi: scsi_debug: Fix request sense
scsi: lpfc: Fix typo in comment for ULP
scsi: ufs-mediatek: Prevent LPM operation on undeclared VCC
scsi: iscsi: Do not put host in iscsi_set_flashnode_param()
scsi: hpsa: Correct ctrl queue depth
scsi: target: tcmu: Make TMR notification optional
scsi: target: tcmu: Implement tmr_notify callback
scsi: target: tcmu: Fix and simplify timeout handling
scsi: target: tcmu: Factor out new helper ring_insert_padding
scsi: target: tcmu: Do not queue aborted commands
scsi: target: tcmu: Use priv pointer in se_cmd
scsi: target: Add tmr_notify backend function
scsi: target: Modify core_tmr_abort_task()
scsi: target: iscsi: Fix inconsistent debug message
scsi: target: iscsi: Fix login error when receiving
...
Update lpfc version to 12.8.0.3
Link: https://lore.kernel.org/r/20200803210229.23063-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On devices that support FCP sequence error recovery, which attempts to
preserve the devices login across link bounce, adisc is used for device
validation. Turns out the device fc4 type is cleared as part of the link
bounce, but the ADISC handling doesn't restore the FC4 support as it
normally would with a PRLI. This caused situations where the device wasn't
reregistered with the transport thus scan logic and LUN discovery never
kicked in.
In the ADISC completion handling, reset the fc4 type so that transport port
reregistration occurs with the remote port.
Link: https://lore.kernel.org/r/20200803210229.23063-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a couple of code areas which validate sufficient reply buffer
length, but the checks are using the request elements rather than the reply
elements.
Rework to validate using the reply structures.
Link: https://lore.kernel.org/r/20200803210229.23063-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With port bounce/address swaps and timing between initiator GID queries vs
remote port FC4 support registrations, the driver may be in a situation
where it sends PRLIs for both FCP and NVME even though the target may not
support one of the protocols. In this case, the remote port will reject the
PRLI and usually indicate it does not support the request. However, the
driver currently ignores the status of the failure and immediately retries
the PRLI, which is pointless. In the case of this one remote port, the
reception of the PRLI retry caused it to decide to send a LOGO. The LOGO
restarted the process and the same results happened. It made the remote
port undiscoverable to either protocol.
Add logic to detect the non-support status and not attempt the retry
of the PRLI.
Link: https://lore.kernel.org/r/20200803210229.23063-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While mds diagnostic tests are running, if the driver is requested to be
unloaded, oops or hangs are observed. The driver doesn't terminate the
processing of diag frames when the unload is started. As such: oops may be
seen for __lpfc_sli_release_iocbq_s4 because ring memory is referenced that
was already freed; or hangs see in lpfc_nvme_wait_for_io_drain as ios no
longer complete.
If unloading, don't process diag frames. Just clean them up.
Link: https://lore.kernel.org/r/20200803210229.23063-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In configs with a large number of initiators in the same zone (>250), RSCN
timeouts are seen when creating or deleting vports:
lpfc 0000:07:00.1: 5:(0):0231 RSCN timeout Data: x0 x3
During RSCN processing driver issues GID_FT command to nameserver. A
counter for number of simultaneous GID_FT commands is maintained (an
unsigned value). The counter is incremented when the GID_FT is issued. If
the GID_FT command fails for some reason the driver retries the GID_FT from
the completion call back. But the counter was decremented before the retry
was issued. When the second GID_FT completes, the callback again tries to
decrement the counter, possibly wrapping to a very large non-zero value,
which causes the RSCN cleanup code to not execute. Thus the RSCN timeout
failure.
Do not decrement the counter on a retry. Also add defensive checks to
ensure the counter is not decremented if already zero.
Link: https://lore.kernel.org/r/20200803210229.23063-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If module parameters override the default configuration settings for
hardware queues or irqs, the driver was not notifying the change from
defaults.
Revise such that any changes will result in a kernel log message.
Link: https://lore.kernel.org/r/20200803210229.23063-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current Link speed was shown as "unknown" in sysfs for FCoE ports. In this
scenario, the port was working in 20G speed, which happens to not be a
speed handled by the driver.
Add support for all possible link speeds that could get reported from
port_speed field in link state ACQE.
Additionally, as supported_speeds can't be manipulated via the FCoE driver
on a converged ethernet port (it must be managed by the nic function),
don't fill out the supported_speeds field for the fc host object in sysfs.
Revise debug logging to report Link speed mgmt valuess.
Link: https://lore.kernel.org/r/20200803210229.23063-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_init() misses a call misc_deregister() in an error path. Add a label
'unregister' to fix it.
Link: https://lore.kernel.org/r/20200731065639.190646-1-jingxiangfeng@huawei.com
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We cannot wait on a completion object in the lpfc_nvme_targetport structure
in the _destroy_targetport() code path because the NVMe/fc transport will
free that structure immediately after the .targetport_delete() callback.
This results in a use-after-free, and a crash if slub_debug=FZPU is
enabled.
An earlier fix put put the completion on the stack, but commit 2a0fb340fc
("scsi: lpfc: Correct localport timeout duration error") subsequently
changed the code to reference the completion through a pointer in the
object rather than the local stack variable. Fix this by using the stack
variable directly.
Link: https://lore.kernel.org/r/20200729231011.13240-1-emilne@redhat.com
Fixes: 2a0fb340fc ("scsi: lpfc: Correct localport timeout duration error")
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nportdisc.c:1079: warning: Function parameter or member 'ndlp' not described in 'lpfc_release_rpi'
Link: https://lore.kernel.org/r/20200723122446.1329773-20-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding, removing and correcting function parameter descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Function parameter or member 'vport' not described in 'lpfc_reg_vpi'
drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Excess function parameter 'phba' description in 'lpfc_reg_vpi'
drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Excess function parameter 'vpi' description in 'lpfc_reg_vpi'
drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Excess function parameter 'sid' description in 'lpfc_reg_vpi'
drivers/scsi/lpfc/lpfc_mbox.c:1218: warning: Function parameter or member 'ring' not described in 'lpfc_config_ring'
drivers/scsi/lpfc/lpfc_mbox.c:1626: warning: Function parameter or member 'mboxq' not described in 'lpfc_mbox_tmo_val'
drivers/scsi/lpfc/lpfc_mbox.c:1626: warning: Excess function parameter 'cmd' description in 'lpfc_mbox_tmo_val'
drivers/scsi/lpfc/lpfc_mbox.c:1710: warning: Function parameter or member 'sge' not described in 'lpfc_sli4_mbx_sge_get'
drivers/scsi/lpfc/lpfc_mbox.c:1780: warning: Function parameter or member 'emb' not described in 'lpfc_sli4_config'
drivers/scsi/lpfc/lpfc_mbox.c:2027: warning: Function parameter or member 'mboxq' not described in 'lpfc_sli4_mbx_read_fcf_rec'
drivers/scsi/lpfc/lpfc_mbox.c:2078: warning: Function parameter or member 'phba' not described in 'lpfc_request_features'
Link: https://lore.kernel.org/r/20200723122446.1329773-19-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_init.c:1136: warning: Function parameter or member 't' not described in 'lpfc_hb_timeout'
drivers/scsi/lpfc/lpfc_init.c:1136: warning: Excess function parameter 'ptr' description in 'lpfc_hb_timeout'
drivers/scsi/lpfc/lpfc_init.c:1170: warning: Function parameter or member 't' not described in 'lpfc_rrq_timeout'
drivers/scsi/lpfc/lpfc_init.c:1170: warning: Excess function parameter 'ptr' description in 'lpfc_rrq_timeout'
drivers/scsi/lpfc/lpfc_init.c:1232: warning: Function parameter or member 'work' not described in 'lpfc_idle_stat_delay_work'
drivers/scsi/lpfc/lpfc_init.c:1817: warning: Function parameter or member 'en_rn_msg' not described in 'lpfc_sli4_port_sta_fn_reset'
drivers/scsi/lpfc/lpfc_init.c:3033: warning: Function parameter or member 'mbx_action' not described in 'lpfc_block_mgmt_io'
drivers/scsi/lpfc/lpfc_init.c:3481: warning: Function parameter or member 'mbx_action' not described in 'lpfc_offline_prep'
drivers/scsi/lpfc/lpfc_init.c:4150: warning: Function parameter or member 'phba' not described in 'lpfc_new_io_buf'
drivers/scsi/lpfc/lpfc_init.c:4150: warning: Function parameter or member 'num_to_alloc' not described in 'lpfc_new_io_buf'
drivers/scsi/lpfc/lpfc_init.c:4150: warning: Excess function parameter 'vport' description in 'lpfc_new_io_buf'
drivers/scsi/lpfc/lpfc_init.c:4150: warning: Excess function parameter 'num_to_allocate' description in 'lpfc_new_io_buf'
drivers/scsi/lpfc/lpfc_init.c:4736: warning: Function parameter or member 't' not described in 'lpfc_sli4_fcf_redisc_wait_tmo'
drivers/scsi/lpfc/lpfc_init.c:4736: warning: Excess function parameter 'ptr' description in 'lpfc_sli4_fcf_redisc_wait_tmo'
drivers/scsi/lpfc/lpfc_init.c:5103: warning: Excess function parameter 'evt_code' description in 'lpfc_async_link_speed_to_read_top'
drivers/scsi/lpfc/lpfc_init.c:5377: warning: Function parameter or member 'acqe_sli' not described in 'lpfc_sli4_async_sli_evt'
drivers/scsi/lpfc/lpfc_init.c:5377: warning: Excess function parameter 'acqe_fc' description in 'lpfc_sli4_async_sli_evt'
drivers/scsi/lpfc/lpfc_init.c:5634: warning: Function parameter or member 'phba' not described in 'lpfc_sli4_perform_all_vport_cvl'
drivers/scsi/lpfc/lpfc_init.c:5634: warning: Excess function parameter 'vport' description in 'lpfc_sli4_perform_all_vport_cvl'
drivers/scsi/lpfc/lpfc_init.c:5655: warning: Function parameter or member 'acqe_fip' not described in 'lpfc_sli4_async_fip_evt'
drivers/scsi/lpfc/lpfc_init.c:5655: warning: Excess function parameter 'acqe_link' description in 'lpfc_sli4_async_fip_evt'
drivers/scsi/lpfc/lpfc_init.c:5908: warning: Function parameter or member 'acqe_dcbx' not described in 'lpfc_sli4_async_dcbx_evt'
drivers/scsi/lpfc/lpfc_init.c:5908: warning: Excess function parameter 'acqe_link' description in 'lpfc_sli4_async_dcbx_evt'
drivers/scsi/lpfc/lpfc_init.c:5927: warning: Function parameter or member 'acqe_grp5' not described in 'lpfc_sli4_async_grp5_evt'
drivers/scsi/lpfc/lpfc_init.c:5927: warning: Excess function parameter 'acqe_link' description in 'lpfc_sli4_async_grp5_evt'
drivers/scsi/lpfc/lpfc_init.c:7279: warning: Function parameter or member 'iocb_count' not described in 'lpfc_init_iocb_list'
drivers/scsi/lpfc/lpfc_init.c:8227: warning: Function parameter or member 'if_type' not described in 'lpfc_sli4_bar1_register_memmap'
drivers/scsi/lpfc/lpfc_init.c:8414: warning: Excess function parameter 'phba' description in 'LINK_FLAGS_DEF'
drivers/scsi/lpfc/lpfc_init.c:8414: warning: Excess function parameter 'rdconf' description in 'LINK_FLAGS_DEF'
drivers/scsi/lpfc/lpfc_init.c:10734: warning: Function parameter or member 'cfg_mode' not described in 'lpfc_sli_enable_intr'
drivers/scsi/lpfc/lpfc_init.c:11241: warning: Function parameter or member 'eqlist' not described in 'lpfc_cpuhp_get_eq'
drivers/scsi/lpfc/lpfc_init.c:11726: warning: Function parameter or member 'cfg_mode' not described in 'lpfc_sli4_enable_intr'
drivers/scsi/lpfc/lpfc_init.c:12997: warning: Excess function parameter 'ret' description in 'lpfc_write_firmware'
drivers/scsi/lpfc/lpfc_init.c:13103: warning: Function parameter or member 'fw_upgrade' not described in 'lpfc_sli4_request_firmware_update'
Link: https://lore.kernel.org/r/20200723122446.1329773-17-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_init.c: In function ‘lpfc_dbg_print’:
drivers/scsi/lpfc/lpfc_init.c:14212:6: warning: function ‘lpfc_dbg_print’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
14212 | sizeof(phba->dbg_log[idx].log), fmt, args);
| ^~~~~~
Link: https://lore.kernel.org/r/20200723122446.1329773-16-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_hbadisc.c:1209: warning: Function parameter or member 'phba' not described in 'lpfc_sli4_clear_fcf_rr_bmask'
drivers/scsi/lpfc/lpfc_hbadisc.c:1309: warning: Function parameter or member 'sw_name' not described in 'lpfc_sw_name_match'
drivers/scsi/lpfc/lpfc_hbadisc.c:1309: warning: Excess function parameter 'fab_name' description in 'lpfc_sw_name_match'
drivers/scsi/lpfc/lpfc_hbadisc.c:1397: warning: Function parameter or member 'fcf_rec' not described in 'lpfc_copy_fcf_record'
drivers/scsi/lpfc/lpfc_hbadisc.c:1397: warning: Excess function parameter 'fcf' description in 'lpfc_copy_fcf_record'
drivers/scsi/lpfc/lpfc_hbadisc.c:1956: warning: Cannot understand lpfc_sli4_fcf_record_match - testing new FCF record for matching existing FCF
on line 1956 - I thought it was a doc line
drivers/scsi/lpfc/lpfc_hbadisc.c:2078: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_pri_list_del'
drivers/scsi/lpfc/lpfc_hbadisc.c:2109: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_set_fcf_flogi_fail'
drivers/scsi/lpfc/lpfc_hbadisc.c:2135: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_pri_list_add'
drivers/scsi/lpfc/lpfc_hbadisc.c:2135: warning: Function parameter or member 'new_fcf_record' not described in 'lpfc_sli4_fcf_pri_list_add'
Link: https://lore.kernel.org/r/20200723122446.1329773-3-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_els.c:3619: warning: Function parameter or member 't' not described in 'lpfc_els_retry_delay'
drivers/scsi/lpfc/lpfc_els.c:3619: warning: Excess function parameter 'ptr' description in 'lpfc_els_retry_delay'
drivers/scsi/lpfc/lpfc_els.c:4877: warning: Function parameter or member 'rejectError' not described in 'lpfc_els_rsp_reject'
drivers/scsi/lpfc/lpfc_els.c:7900: warning: Function parameter or member 't' not described in 'lpfc_els_timeout'
drivers/scsi/lpfc/lpfc_els.c:7900: warning: Excess function parameter 'ptr' description in 'lpfc_els_timeout'
drivers/scsi/lpfc/lpfc_els.c:8272: warning: Function parameter or member 'payload' not described in 'lpfc_send_els_event'
drivers/scsi/lpfc/lpfc_els.c:8272: warning: Excess function parameter 'cmd' description in 'lpfc_send_els_event'
drivers/scsi/lpfc/lpfc_els.c:8355: warning: Function parameter or member 'tlv' not described in 'lpfc_els_rcv_fpin_li'
drivers/scsi/lpfc/lpfc_els.c:8355: warning: Excess function parameter 'lnk_not' description in 'lpfc_els_rcv_fpin_li'
drivers/scsi/lpfc/lpfc_els.c:9688: warning: Function parameter or member 't' not described in 'lpfc_fabric_block_timeout'
drivers/scsi/lpfc/lpfc_els.c:9688: warning: Excess function parameter 'ptr' description in 'lpfc_fabric_block_timeout'
Link: https://lore.kernel.org/r/20200723122446.1329773-2-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'pg_addr' is only used when CONFIG_X86 is defined. So only declare it if
CONFIG_X86 is defined.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_sli.c: In function ‘lpfc_wq_create’:
drivers/scsi/lpfc/lpfc_sli.c:15813:16: warning: unused variable ‘pg_addr’ [-Wunused-variable]
15813 | unsigned long pg_addr;
| ^~~~~~~
Link: https://lore.kernel.org/r/20200721164148.2617584-37-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Other headers have been demoted as they are too far out of sync and ideally
require effort from the authors.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_ct.c:321: warning: Function parameter or member 'usr_flg' not described in 'lpfc_gen_req'
drivers/scsi/lpfc/lpfc_ct.c:321: warning: Function parameter or member 'num_entry' not described in 'lpfc_gen_req'
drivers/scsi/lpfc/lpfc_ct.c:321: warning: Function parameter or member 'tmo' not described in 'lpfc_gen_req'
drivers/scsi/lpfc/lpfc_ct.c:321: warning: Function parameter or member 'retry' not described in 'lpfc_gen_req'
drivers/scsi/lpfc/lpfc_ct.c:413: warning: Function parameter or member 'rsp_size' not described in 'lpfc_ct_cmd'
drivers/scsi/lpfc/lpfc_ct.c:413: warning: Function parameter or member 'retry' not described in 'lpfc_ct_cmd'
drivers/scsi/lpfc/lpfc_ct.c:3030: warning: Function parameter or member 'cmdcode' not described in 'lpfc_fdmi_cmd'
drivers/scsi/lpfc/lpfc_ct.c:3030: warning: Function parameter or member 'new_mask' not described in 'lpfc_fdmi_cmd'
drivers/scsi/lpfc/lpfc_ct.c:3272: warning: Function parameter or member 't' not described in 'lpfc_delayed_disc_tmo'
Link: https://lore.kernel.org/r/20200721164148.2617584-31-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_sli.c:257: warning: Function parameter or member 'mqe' not described in 'lpfc_sli4_mq_put'
drivers/scsi/lpfc/lpfc_sli.c:257: warning: Excess function parameter 'wqe' description in 'lpfc_sli4_mq_put'
drivers/scsi/lpfc/lpfc_sli.c:675: warning: Function parameter or member 'hq' not described in 'lpfc_sli4_rq_put'
drivers/scsi/lpfc/lpfc_sli.c:675: warning: Function parameter or member 'dq' not described in 'lpfc_sli4_rq_put'
drivers/scsi/lpfc/lpfc_sli.c:675: warning: Function parameter or member 'hrqe' not described in 'lpfc_sli4_rq_put'
drivers/scsi/lpfc/lpfc_sli.c:675: warning: Function parameter or member 'drqe' not described in 'lpfc_sli4_rq_put'
drivers/scsi/lpfc/lpfc_sli.c:675: warning: Excess function parameter 'q' description in 'lpfc_sli4_rq_put'
drivers/scsi/lpfc/lpfc_sli.c:675: warning: Excess function parameter 'wqe' description in 'lpfc_sli4_rq_put'
drivers/scsi/lpfc/lpfc_sli.c:738: warning: Function parameter or member 'hq' not described in 'lpfc_sli4_rq_release'
drivers/scsi/lpfc/lpfc_sli.c:738: warning: Function parameter or member 'dq' not described in 'lpfc_sli4_rq_release'
drivers/scsi/lpfc/lpfc_sli.c:738: warning: Excess function parameter 'q' description in 'lpfc_sli4_rq_release'
drivers/scsi/lpfc/lpfc_sli.c:1021: warning: Function parameter or member 'xritag' not described in 'lpfc_test_rrq_active'
drivers/scsi/lpfc/lpfc_sli.c:1132: warning: Function parameter or member 'piocbq' not described in '__lpfc_sli_get_els_sglq'
drivers/scsi/lpfc/lpfc_sli.c:1132: warning: Excess function parameter 'piocb' description in '__lpfc_sli_get_els_sglq'
drivers/scsi/lpfc/lpfc_sli.c:1207: warning: Function parameter or member 'piocbq' not described in '__lpfc_sli_get_nvmet_sglq'
drivers/scsi/lpfc/lpfc_sli.c:1207: warning: Excess function parameter 'piocb' description in '__lpfc_sli_get_nvmet_sglq'
drivers/scsi/lpfc/lpfc_sli.c:2243: warning: Function parameter or member 'rb_list' not described in 'lpfc_sli_hbqbuf_get'
drivers/scsi/lpfc/lpfc_sli.c:2243: warning: Excess function parameter 'phba' description in 'lpfc_sli_hbqbuf_get'
drivers/scsi/lpfc/lpfc_sli.c:2243: warning: Excess function parameter 'hbqno' description in 'lpfc_sli_hbqbuf_get'
drivers/scsi/lpfc/lpfc_sli.c:2262: warning: Function parameter or member 'hrq' not described in 'lpfc_sli_rqbuf_get'
drivers/scsi/lpfc/lpfc_sli.c:2262: warning: Excess function parameter 'hbqno' description in 'lpfc_sli_rqbuf_get'
drivers/scsi/lpfc/lpfc_sli.c:3429: warning: Function parameter or member 't' not described in 'lpfc_poll_eratt'
drivers/scsi/lpfc/lpfc_sli.c:3429: warning: Excess function parameter 'ptr' description in 'lpfc_poll_eratt'
drivers/scsi/lpfc/lpfc_sli.c:4115: warning: Excess function parameter 'pring' description in 'lpfc_sli_abort_fcp_rings'
drivers/scsi/lpfc/lpfc_sli.c:5331: warning: Excess function parameter 'mboxq' description in 'lpfc_sli4_read_fcoe_params'
drivers/scsi/lpfc/lpfc_sli.c:5879: warning: Function parameter or member 'extnt_cnt' not described in 'lpfc_sli4_cfg_post_extnts'
drivers/scsi/lpfc/lpfc_sli.c:5879: warning: Function parameter or member 'type' not described in 'lpfc_sli4_cfg_post_extnts'
drivers/scsi/lpfc/lpfc_sli.c:5879: warning: Function parameter or member 'emb' not described in 'lpfc_sli4_cfg_post_extnts'
drivers/scsi/lpfc/lpfc_sli.c:5879: warning: Function parameter or member 'mbox' not described in 'lpfc_sli4_cfg_post_extnts'
drivers/scsi/lpfc/lpfc_sli.c:6459: warning: Function parameter or member 'pmb' not described in 'lpfc_sli4_ras_mbox_cmpl'
drivers/scsi/lpfc/lpfc_sli.c:6459: warning: Excess function parameter 'pmboxq' description in 'lpfc_sli4_ras_mbox_cmpl'
drivers/scsi/lpfc/lpfc_sli.c:6912: warning: Function parameter or member 'extnt_cnt' not described in 'lpfc_sli4_get_allocated_extnts'
drivers/scsi/lpfc/lpfc_sli.c:6912: warning: Excess function parameter 'extnt_count' description in 'lpfc_sli4_get_allocated_extnts'
drivers/scsi/lpfc/lpfc_sli.c:7064: warning: Excess function parameter 'pring' description in 'lpfc_sli4_repost_sgl_list'
drivers/scsi/lpfc/lpfc_sli.c:7312: warning: Function parameter or member 'phba' not described in 'lpfc_init_idle_stat_hb'
drivers/scsi/lpfc/lpfc_sli.c:8022: warning: Function parameter or member 't' not described in 'lpfc_mbox_timeout'
drivers/scsi/lpfc/lpfc_sli.c:8022: warning: Excess function parameter 'ptr' description in 'lpfc_mbox_timeout'
drivers/scsi/lpfc/lpfc_sli.c:8902: warning: Function parameter or member 'mboxq' not described in 'lpfc_sli_issue_mbox_s4'
drivers/scsi/lpfc/lpfc_sli.c:8902: warning: Excess function parameter 'pmbox' description in 'lpfc_sli_issue_mbox_s4'
drivers/scsi/lpfc/lpfc_sli.c:9413: warning: Function parameter or member 'piocbq' not described in 'lpfc_sli4_bpl2sgl'
drivers/scsi/lpfc/lpfc_sli.c:9413: warning: Excess function parameter 'piocb' description in 'lpfc_sli4_bpl2sgl'
drivers/scsi/lpfc/lpfc_sli.c:9518: warning: Function parameter or member 'iocbq' not described in 'lpfc_sli4_iocb2wqe'
drivers/scsi/lpfc/lpfc_sli.c:9518: warning: Excess function parameter 'piocb' description in 'lpfc_sli4_iocb2wqe'
drivers/scsi/lpfc/lpfc_sli.c:10212: warning: Function parameter or member 'phba' not described in '__lpfc_sli_issue_iocb'
drivers/scsi/lpfc/lpfc_sli.c:10212: warning: Function parameter or member 'ring_number' not described in '__lpfc_sli_issue_iocb'
drivers/scsi/lpfc/lpfc_sli.c:10212: warning: Function parameter or member 'piocb' not described in '__lpfc_sli_issue_iocb'
drivers/scsi/lpfc/lpfc_sli.c:10212: warning: Function parameter or member 'flag' not described in '__lpfc_sli_issue_iocb'
drivers/scsi/lpfc/lpfc_sli.c:10300: warning: Function parameter or member 'ring_number' not described in 'lpfc_sli_issue_iocb'
drivers/scsi/lpfc/lpfc_sli.c:10300: warning: Excess function parameter 'pring' description in 'lpfc_sli_issue_iocb'
drivers/scsi/lpfc/lpfc_sli.c:11807: warning: Function parameter or member 'cmd' not described in 'lpfc_sli_abort_taskmgmt'
drivers/scsi/lpfc/lpfc_sli.c:11807: warning: Excess function parameter 'taskmgmt_cmd' description in 'lpfc_sli_abort_taskmgmt'
drivers/scsi/lpfc/lpfc_sli.c:12067: warning: Function parameter or member 'ring_number' not described in 'lpfc_sli_issue_iocb_wait'
drivers/scsi/lpfc/lpfc_sli.c:12067: warning: Excess function parameter 'pring' description in 'lpfc_sli_issue_iocb_wait'
drivers/scsi/lpfc/lpfc_sli.c:12262: warning: Function parameter or member 'mbx_action' not described in 'lpfc_sli_mbox_sys_shutdown'
drivers/scsi/lpfc/lpfc_sli.c:13219: warning: Function parameter or member 'irspiocbq' not described in 'lpfc_sli4_els_wcqe_to_rspiocbq'
drivers/scsi/lpfc/lpfc_sli.c:13219: warning: Excess function parameter 'wcqe' description in 'lpfc_sli4_els_wcqe_to_rspiocbq'
drivers/scsi/lpfc/lpfc_sli.c:13285: warning: Function parameter or member 'mcqe' not described in 'lpfc_sli4_sp_handle_async_event'
drivers/scsi/lpfc/lpfc_sli.c:13285: warning: Excess function parameter 'cqe' description in 'lpfc_sli4_sp_handle_async_event'
drivers/scsi/lpfc/lpfc_sli.c:13318: warning: Function parameter or member 'mcqe' not described in 'lpfc_sli4_sp_handle_mbox_event'
drivers/scsi/lpfc/lpfc_sli.c:13318: warning: Excess function parameter 'cqe' description in 'lpfc_sli4_sp_handle_mbox_event'
drivers/scsi/lpfc/lpfc_sli.c:13441: warning: Function parameter or member 'cq' not described in 'lpfc_sli4_sp_handle_mcqe'
drivers/scsi/lpfc/lpfc_sli.c:13768: warning: Function parameter or member 'speq' not described in 'lpfc_sli4_sp_handle_eqe'
drivers/scsi/lpfc/lpfc_sli.c:14126: warning: Function parameter or member 'cq' not described in 'lpfc_sli4_nvmet_handle_rcqe'
drivers/scsi/lpfc/lpfc_sli.c:14235: warning: Function parameter or member 'cqe' not described in 'lpfc_sli4_fp_handle_cqe'
drivers/scsi/lpfc/lpfc_sli.c:14235: warning: Excess function parameter 'eqe' description in 'lpfc_sli4_fp_handle_cqe'
drivers/scsi/lpfc/lpfc_sli.c:14336: warning: Function parameter or member 'eq' not described in 'lpfc_sli4_hba_handle_eqe'
drivers/scsi/lpfc/lpfc_sli.c:14808: warning: Function parameter or member 'entry_count' not described in 'lpfc_sli4_queue_alloc'
drivers/scsi/lpfc/lpfc_sli.c:15185: warning: Function parameter or member 'type' not described in 'lpfc_cq_create'
drivers/scsi/lpfc/lpfc_sli.c:15185: warning: Function parameter or member 'subtype' not described in 'lpfc_cq_create'
drivers/scsi/lpfc/lpfc_sli.c:15333: warning: Function parameter or member 'type' not described in 'lpfc_cq_create_set'
drivers/scsi/lpfc/lpfc_sli.c:15333: warning: Function parameter or member 'subtype' not described in 'lpfc_cq_create_set'
drivers/scsi/lpfc/lpfc_sli.c:16063: warning: Function parameter or member 'subtype' not described in 'lpfc_rq_create'
drivers/scsi/lpfc/lpfc_sli.c:16353: warning: Function parameter or member 'subtype' not described in 'lpfc_mrq_create'
drivers/scsi/lpfc/lpfc_sli.c:16533: warning: Function parameter or member 'phba' not described in 'lpfc_eq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16590: warning: Function parameter or member 'phba' not described in 'lpfc_cq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16644: warning: Function parameter or member 'phba' not described in 'lpfc_mq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16644: warning: Function parameter or member 'mq' not described in 'lpfc_mq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16644: warning: Excess function parameter 'qm' description in 'lpfc_mq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16698: warning: Function parameter or member 'phba' not described in 'lpfc_wq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16754: warning: Function parameter or member 'phba' not described in 'lpfc_rq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16754: warning: Function parameter or member 'hrq' not described in 'lpfc_rq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16754: warning: Function parameter or member 'drq' not described in 'lpfc_rq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16754: warning: Excess function parameter 'rq' description in 'lpfc_rq_destroy'
drivers/scsi/lpfc/lpfc_sli.c:16940: warning: Function parameter or member 'xri' not described in '__lpfc_sli4_free_xri'
drivers/scsi/lpfc/lpfc_sli.c:16955: warning: Function parameter or member 'xri' not described in 'lpfc_sli4_free_xri'
drivers/scsi/lpfc/lpfc_sli.c:17002: warning: Function parameter or member 'post_cnt' not described in 'lpfc_sli4_post_sgl_list'
drivers/scsi/lpfc/lpfc_sli.c:17002: warning: Excess function parameter 'count' description in 'lpfc_sli4_post_sgl_list'
drivers/scsi/lpfc/lpfc_sli.c:17221: warning: Function parameter or member 'sb_count' not described in 'lpfc_sli4_post_io_sgl_list'
drivers/scsi/lpfc/lpfc_sli.c:17451: warning: Function parameter or member 'did' not described in 'lpfc_fc_frame_to_vport'
drivers/scsi/lpfc/lpfc_sli.c:17590: warning: Function parameter or member 'vport' not described in 'lpfc_fc_frame_add'
drivers/scsi/lpfc/lpfc_sli.c:17817: warning: Function parameter or member 'vport' not described in 'lpfc_sli4_seq_abort_rsp'
drivers/scsi/lpfc/lpfc_sli.c:17817: warning: Function parameter or member 'aborted' not described in 'lpfc_sli4_seq_abort_rsp'
drivers/scsi/lpfc/lpfc_sli.c:17817: warning: Excess function parameter 'phba' description in 'lpfc_sli4_seq_abort_rsp'
drivers/scsi/lpfc/lpfc_sli.c:18060: warning: Function parameter or member 'seq_dmabuf' not described in 'lpfc_prep_seq'
drivers/scsi/lpfc/lpfc_sli.c:18060: warning: Excess function parameter 'dmabuf' description in 'lpfc_prep_seq'
drivers/scsi/lpfc/lpfc_sli.c:18332: warning: Function parameter or member 'dmabuf' not described in 'lpfc_sli4_handle_received_buffer'
drivers/scsi/lpfc/lpfc_sli.c:18655: warning: Function parameter or member 'rpi' not described in '__lpfc_sli4_free_rpi'
drivers/scsi/lpfc/lpfc_sli.c:18683: warning: Function parameter or member 'rpi' not described in 'lpfc_sli4_free_rpi'
drivers/scsi/lpfc/lpfc_sli.c:18714: warning: Function parameter or member 'ndlp' not described in 'lpfc_sli4_resume_rpi'
drivers/scsi/lpfc/lpfc_sli.c:18714: warning: Function parameter or member 'cmpl' not described in 'lpfc_sli4_resume_rpi'
drivers/scsi/lpfc/lpfc_sli.c:18714: warning: Function parameter or member 'arg' not described in 'lpfc_sli4_resume_rpi'
drivers/scsi/lpfc/lpfc_sli.c:18714: warning: Excess function parameter 'phba' description in 'lpfc_sli4_resume_rpi'
drivers/scsi/lpfc/lpfc_sli.c:19103: warning: Function parameter or member 'phba' not described in 'lpfc_check_next_fcf_pri_level'
drivers/scsi/lpfc/lpfc_sli.c:19266: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_rr_index_set'
drivers/scsi/lpfc/lpfc_sli.c:19295: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_rr_index_clear'
drivers/scsi/lpfc/lpfc_sli.c:19331: warning: Function parameter or member 'mbox' not described in 'lpfc_mbx_cmpl_redisc_fcf_table'
drivers/scsi/lpfc/lpfc_sli.c:20027: warning: Function parameter or member 'pwqeq' not described in 'lpfc_wqe_bpl2sgl'
drivers/scsi/lpfc/lpfc_sli.c:20027: warning: Excess function parameter 'pwqe' description in 'lpfc_wqe_bpl2sgl'
drivers/scsi/lpfc/lpfc_sli.c:20141: warning: Function parameter or member 'qp' not described in 'lpfc_sli4_issue_wqe'
drivers/scsi/lpfc/lpfc_sli.c:20141: warning: Excess function parameter 'ring_number' description in 'lpfc_sli4_issue_wqe'
drivers/scsi/lpfc/lpfc_sli.c:20434: warning: Function parameter or member 'qp' not described in '_lpfc_move_xri_pbl_to_pvt'
drivers/scsi/lpfc/lpfc_sli.c:20552: warning: Function parameter or member 'hwqid' not described in 'lpfc_keep_pvt_pool_above_lowwm'
drivers/scsi/lpfc/lpfc_sli.c:20552: warning: Excess function parameter 'qp' description in 'lpfc_keep_pvt_pool_above_lowwm'
drivers/scsi/lpfc/lpfc_sli.c:20682: warning: Function parameter or member 'qp' not described in 'lpfc_get_io_buf_from_private_pool'
Link: https://lore.kernel.org/r/20200721164148.2617584-24-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_sli.c: In function ‘lpfc_wq_create’:
drivers/scsi/lpfc/lpfc_sli.c:15810:16: warning: variable ‘pg_addr’ set but not used [-Wunused-but-set-variable]
15810 | unsigned long pg_addr;
| ^~~~~~~
Link: https://lore.kernel.org/r/20200721164148.2617584-21-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Either due to API slippage before the driver was mainlined or copy/paste
errors.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvme.c:254: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_create_queue'
drivers/scsi/lpfc/lpfc_nvme.c:254: warning: Function parameter or member 'qsize' not described in 'lpfc_nvme_create_queue'
drivers/scsi/lpfc/lpfc_nvme.c:254: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_create_queue'
drivers/scsi/lpfc/lpfc_nvme.c:311: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_delete_queue'
drivers/scsi/lpfc/lpfc_nvme.c:311: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_delete_queue'
drivers/scsi/lpfc/lpfc_nvme.c:689: warning: Function parameter or member 'gen_req_cmp' not described in '__lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Function parameter or member 'pnvme_lsreq' not described in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Function parameter or member 'pnvme_lsreq' not described in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Function parameter or member 'phba' not described in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Function parameter or member 'pwqeIn' not described in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Function parameter or member 'wcqe' not described in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Function parameter or member 'pnode' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Function parameter or member 'cstat' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'hw_queue_handle' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'hw_queue_handle' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1598: warning: bad line: indicated in @lpfc_nvme_rport.
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1856: warning: Function parameter or member 'abts_cmpl' not described in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1856: warning: Excess function parameter 'rspiocb' description in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:2093: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2093: warning: Function parameter or member 'idx' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2093: warning: Function parameter or member 'expedite' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2197: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_create_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2330: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2330: warning: Excess function parameter 'pnvme' description in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2543: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_rescan_port'
drivers/scsi/lpfc/lpfc_nvme.c:2543: warning: Function parameter or member 'ndlp' not described in 'lpfc_nvme_rescan_port'
Link: https://lore.kernel.org/r/20200713080001.128044-21-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
nvme-fc allows the driver to specify a default devloss_tmo value when
registering the remote port. The lpfc driver is currently not doing so,
although it is implementing a driver internal node loss value of 30s which
also is used on the SCSI FC remote port. As no devloss_tmo is set, the
nvme-fc transport defaults to 60s. So there are competing timers.
Additionally, due to the competing timers, it is possible the NVMe rport is
removed but the SCSI rport remains. It is possible that the SCSI FC rport,
which was registered for the NVMe port even if it doesn't utilize the SCSI
protocol, had been tuned to not match either the 60s (nvme-fc default) or
30s (lldd default), it gets out of whack. The lldd will defer to the SCSI
FC rport as long as the SCSI FC rport has not had its devloss_tmo expire.
Correct the situation by specifying a default devloss_tmo to the nvme-fc
transport when registering the rport. Take the value from the SCSI FC
rport if it exists, otherwise use the driver default.
Link: https://lore.kernel.org/r/20200714211412.11773-1-jsmart2021@gmail.com
Tested-by: Martin George <Martin.George@netapp.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On a big box the lpfc driver emits a few thousand "Set Affinity" lines to
the console. Reduce the priority of these from KERN_ERR to KERN_INFO, and
also fix a few printks that had no log level.
Link: https://lore.kernel.org/r/20200713083908.1104927-1-anton@ozlabs.org
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Anton Blanchard <anton@ozlabs.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The expression start_idx - dbg_cnt is evaluated using unsigned int
arthithmetic (since these variables are unsigned ints) and hence can never
be less than zero, so the less than comparison is never true. Rewrite the
expression to check for start_idx being less than dbg_cnt.
After the logic was corrected, temp_idx wasn't working correctly. So fix it
as well.
Link: https://lore.kernel.org/r/20200706204246.130416-1-jsmart2021@gmail.com
Fixes: 372c187b8a ("scsi: lpfc: Add an internal trace log buffer")
CC: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unsigned compared against 0")
With certain platforms its possible pci_alloc_irq_vectors() may affinitize
irq vectors to multiple (all?) CPUs. The driver is currently assuming
exclusivity and vectors being doled out to different CPUs and is assigning
primary ownership of each vector to the first CPU in the mask. The code
doesn't bother to check if the CPU already owns a vector and will
unconditionally overwrite the CPU to vector mapping. This causes the
relationships between eq's and cq's to get confused and gets worse when
CPUs start to offline. The net results are interrupts are skipped resulting
in mailbox timeouts and there are oopses in CPU offling flows.
Fix this changing up the primary vector assignment. Now assign the eq to a
CPU only if it is the CPU in the mask that does not have a prior
assignment. And once the primary ownership is assigned, break from the
loop. For CPUs that may have been set before but not the primary owner, the
lpfc_cpu_affinity_check() routine will balance the CPU to eq assignment.
Link: https://lore.kernel.org/r/20200706204230.130363-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix smatch warning:
drivers/scsi/lpfc/lpfc_sli.c:15156 lpfc_cq_poll_hdler() warn:
inconsistent indenting
Link: https://lore.kernel.org/r/20200707150018.823350-1-colin.king@canonical.com
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current logging methods typically end up requesting a reproduction with
a different logging level set to figure out what happened. This was mainly
by design to not clutter the kernel log messages with things that were
typically not interesting and the messages themselves could cause other
issues.
When looking to make a better system, it was seen that in many cases when
more data was wanted was when another message, usually at KERN_ERR level,
was logged. And in most cases, what the additional logging that was then
enabled was typically. Most of these areas fell into the discovery machine.
Based on this summary, the following design has been put in place: The
driver will maintain an internal log (256 elements of 256 bytes). The
"additional logging" messages that are usually enabled in a reproduction
will be changed to now log all the time to the internal log. A new logging
level is defined - LOG_TRACE_EVENT. When this level is set (it is not by
default) and a message marked as KERN_ERR is logged, all the messages in
the internal log will be dumped to the kernel log before the KERN_ERR
message is logged.
There is a timestamp on each message added to the internal log. However,
this timestamp is not converted to wall time when logged. The value of the
timestamp is solely to give a crude time reference for the messages.
Link: https://lore.kernel.org/r/20200630215001.70793-14-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Although the existing implementation is very good at high I/O load, on
tests involving light load, especially on only a few hardware queues,
latency was a little higher than it can be due to using workqueue
scheduling. Other tasks in the system can delay handling.
Change the lower level to use irq_poll by default which uses a softirq for
I/O completion. This gives better latency as variance in when the cq is
processed is reduced over the workqueue interface. However, as high load is
better served by not being in softirq when the CPU is loaded, work queues
are still used under high I/O load.
Link: https://lore.kernel.org/r/20200630215001.70793-13-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, if there has been an issue whereby an adapter dump was taken,
there is nothing displayed to hint that it is present. Utilities must be
run and they must query for the status in order to then download the dump.
Add a message to the driver to query dump image presence when initializing
the SLI Port.
Link: https://lore.kernel.org/r/20200630215001.70793-12-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver validates command codes received from the
application. COMMON_SET_FEATURES is not currently being approved.
Add definition of the missing command and allow it to be issued by
applications.
Link: https://lore.kernel.org/r/20200630215001.70793-11-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change vocabulary of 0373 log msg from "error" to "cmpl" The current
language of the 0373 message contains the word "error" which caused a
number of customers to inquire about the "error" and if it should be a
concern. It isn't an error, it's simply an io completion status.
Revise the message to replace the word "error" with "cmpl" for completion.
Link: https://lore.kernel.org/r/20200630215001.70793-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the kdump kernel shuts down lpfc calls flush_work_queue on an
interrupt to schedule the cq handler. When there is only one CPU active on
the kdump kernel, it is possible for the work_on to get scheduled on a
non-active CPU causing it to never be scheduled.
When in the kdump environment, per-CPU affinity of cq's to cpus is not
necessary. In those cases, use a general queue_work rather than a
queue_work_on().
Link: https://lore.kernel.org/r/20200630215001.70793-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When vports are deleted, it is observed that there is memory/kthread
leakage as the vport isn't fully being released.
There is a shost reference taken in scsi_add_host_dma that is not released
during scsi_remove_host. It was noticed that other drivers resolve this by
doing a scsi_host_put after calling scsi_remove_host.
The vport_delete routine is taking two references one that corresponds to
an access to the scsi_host in the vport_delete routine and another that is
released after the adapter mailbox command completes that destroys the VPI
that corresponds to the vport.
Remove one of the references taken such that the second reference that is
put will complete the missing scsi_add_host_dma reference and the shost
will be terminated.
Link: https://lore.kernel.org/r/20200630215001.70793-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Call traces have been observed running different tests that involve aborts
and setting the rrq active flag. The lpfc_set_rrq_active routine is doing
a mempool_alloc under the soft_irq processing level. When the mempool needs
to get a new buffer from the free pool and has to wait for memory to become
free it will check the flags passed in on the alloc and dump the stack if
the thread is running in interrupt context.
Replace the GFP_KERNEL flag with GFP_ATOMIC so that the memory allocation
will not attempt to sleep if there is no mem available.
Link: https://lore.kernel.org/r/20200630215001.70793-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When using DUMP on SLI3 to read VPD and Port status data (config region
23), the adapter is overruning the kmalloc'd buffer causing havoc on other
consumers of the allocation pools.
Rework the loops processing the dump data and validate/size memory lengths
before performing bcopy.
Link: https://lore.kernel.org/r/20200630215001.70793-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During driver unload/reload testing, the NVMe initiator would not
re-establish connectivity to NVMe controllers on reload.
The failing NVMe array supports concurrent FCP and NVMe operation via
different nport_id's. The array was repeatedly sending an ADISC every 2
seconds after PLOGI completed and while NVMe subsystems were executing
discovery. The target would continue this state for roughly 45 seconds.
The driver's current behavior on ADISC receipt is to validate a the ADISC
vs the device and issue a RESUME_RPI to restore transmission. The receipt
of the ADISC effectively caused a driver to take actions similar to a
logout and login for the remote port, causing the deregistration of the
nvme rport and a subsequent re-registration. This caused a constant reset
and re-connect of the NVMe controller while this 45s window occurred. There
was no need for the state changes as ADISC does not change login state.
This patch corrects this behavior by validating if the remoteport is
already logged in (MAPPED) and when true, avoids the call to set the ndlp
state to MAPPED, which triggers the unreg/re-reg. Thus ADISC does not
change the login state of the node.
Link: https://lore.kernel.org/r/20200630215001.70793-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Visual code inspection of the MDS implementation revealed two errors in
the driver:
- The set features Feature Code had an incorrect value
- The routine that classifies command type for cmd completions was missing
the Send Frame definition. Send Frame is used for MDS driver loopback.
Link: https://lore.kernel.org/r/20200630215001.70793-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity reported the following error:
Assigned value that is never used may represent unnecessary computation.
The rc variable was initially assigned a value but in several cases, when
an error case is detected, it is reassigned a new value. The initial value
had little use.
In code-reviewing this routine, it could use some cleanup:
- Setting the initialization value to -ENODEV is a much better choice and
lessens code in the routine.
- The wasn't tracking logic errors vs no error and mailbox failure.
Better to resolve by adding a status to track the mailbox failure
and merge it with the logic error when the routine returns.
Link: https://lore.kernel.org/r/20200630215001.70793-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit cdb42becdd ("scsi: lpfc: Replace io_channels for nvme and fcp with
general hdw_queues per cpu") has introduced static checker warnings for
potential null dereferences in 'lpfc_sli4_hba_unset()' and commit 1ffdd2c044
("scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset") has
tried to fix it. However, yet another potential null dereference is
remaining. This commit fixes it.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Link: https://lore.kernel.org/r/20200623084122.30633-1-sjpark@amazon.com
Fixes: 1ffdd2c044 ("scsi: lpfc: resolve static checker warning inlpfc_sli4_hba_unset")
Fixes: cdb42becdd ("scsi: lpfc: Replace io_channels for nvme and fcp with general hdw_queues per cpu")
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (qla2xxx, ufs, zfcp,
target, scsi_debug, lpfc, qedi, qedf, hisi_sas, mpt3sas) plus a host
of other minor updates. There are no major core changes in this
series apart from a refactoring in scsi_lib.c.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXtq5QyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXyGAQCipTWx
7kHKHZBCVTU133bADt3+SstLrAm8PKZEXMnP9wEAzu4QkkW8URxEDRrpu7qk5gbA
9M/KyqvfRtTH7+BSK7M=
=J6aO
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
:This series consists of the usual driver updates (qla2xxx, ufs, zfcp,
target, scsi_debug, lpfc, qedi, qedf, hisi_sas, mpt3sas) plus a host
of other minor updates.
There are no major core changes in this series apart from a
refactoring in scsi_lib.c"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (207 commits)
scsi: ufs: ti-j721e-ufs: Fix unwinding of pm_runtime changes
scsi: cxgb3i: Fix some leaks in init_act_open()
scsi: ibmvscsi: Make some functions static
scsi: iscsi: Fix deadlock on recovery path during GFP_IO reclaim
scsi: ufs: Fix WriteBooster flush during runtime suspend
scsi: ufs: Fix index of attributes query for WriteBooster feature
scsi: ufs: Allow WriteBooster on UFS 2.2 devices
scsi: ufs: Remove unnecessary memset for dev_info
scsi: ufs-qcom: Fix scheduling while atomic issue
scsi: mpt3sas: Fix reply queue count in non RDPQ mode
scsi: lpfc: Fix lpfc_nodelist leak when processing unsolicited event
scsi: target: tcmu: Fix a use after free in tcmu_check_expired_queue_cmd()
scsi: vhost: Notify TCM about the maximum sg entries supported per command
scsi: qla2xxx: Remove return value from qla_nvme_ls()
scsi: qla2xxx: Remove an unused function
scsi: iscsi: Register sysfs for iscsi workqueue
scsi: scsi_debug: Parser tables and code interaction
scsi: core: Refactor scsi_mq_setup_tags function
scsi: core: Fix incorrect usage of shost_for_each_device
scsi: qla2xxx: Fix endianness annotations in source files
...
-----BEGIN PGP SIGNATURE-----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=H+/Z
-----END PGP SIGNATURE-----
Merge tag 'for-5.8/drivers-2020-06-01' of git://git.kernel.dk/linux-block
Pull block driver updates from Jens Axboe:
"On top of the core changes, here are the block driver changes for this
merge window:
- NVMe changes:
- NVMe over Fibre Channel protocol updates, which also reach
over to drivers/scsi/lpfc (James Smart)
- namespace revalidation support on the target (Anthony
Iliopoulos)
- gcc zero length array fix (Arnd Bergmann)
- nvmet cleanups (Chaitanya Kulkarni)
- misc cleanups and fixes (me, Keith Busch, Sagi Grimberg)
- use a SRQ per completion vector (Max Gurtovoy)
- fix handling of runtime changes to the queue count (Weiping
Zhang)
- t10 protection information support for nvme-rdma and
nvmet-rdma (Israel Rukshin and Max Gurtovoy)
- target side AEN improvements (Chaitanya Kulkarni)
- various fixes and minor improvements all over, icluding the
nvme part of the lpfc driver"
- Floppy code cleanup series (Willy, Denis)
- Floppy contention fix (Jiri)
- Loop CONFIGURE support (Martijn)
- bcache fixes/improvements (Coly, Joe, Colin)
- q->queuedata cleanups (Christoph)
- Get rid of ioctl_by_bdev (Christoph, Stefan)
- md/raid5 allocation fixes (Coly)
- zero length array fixes (Gustavo)
- swim3 task state fix (Xu)"
* tag 'for-5.8/drivers-2020-06-01' of git://git.kernel.dk/linux-block: (166 commits)
bcache: configure the asynchronous registertion to be experimental
bcache: asynchronous devices registration
bcache: fix refcount underflow in bcache_device_free()
bcache: Convert pr_<level> uses to a more typical style
bcache: remove redundant variables i and n
lpfc: Fix return value in __lpfc_nvme_ls_abort
lpfc: fix axchg pointer reference after free and double frees
lpfc: Fix pointer checks and comments in LS receive refactoring
nvme: set dma alignment to qword
nvmet: cleanups the loop in nvmet_async_events_process
nvmet: fix memory leak when removing namespaces and controllers concurrently
nvmet-rdma: add metadata/T10-PI support
nvmet: add metadata support for block devices
nvmet: add metadata/T10-PI support
nvme: add Metadata Capabilities enumerations
nvmet: rename nvmet_check_data_len to nvmet_check_transfer_len
nvmet: rename nvmet_rw_len to nvmet_rw_data_len
nvmet: add metadata characteristics for a namespace
nvme-rdma: add metadata/T10-PI support
nvme-rdma: introduce nvme_rdma_sgl structure
...
No, you do NOT need to "protect copy from user" that way.
Incidentally, your userland ABI stinks. I understand that you
wanted to accept "reset" and "reset\n" as equivalent, but I suspect
that accepting "reset this, you !@^!@!" had been an accident.
Nothing to do about that now - it is a userland ABI...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
A static checker reported the following issue:
drivers/scsi/lpfc/lpfc_nvmet.c:1366 lpfc_nvmet_ls_abort()
warn: 'ret' can be either negative or positive
The comment indicates a non-zero value indicates error in the
form of -Exxx, but the code is returning "1".
Fix the code to return -EINVAL to be compliant to comment.
Fixes: e96a22b0b7 ("lpfc: Refactor Send LS Abort support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The axchg structure is a structure allocated early in the
lpfc_nvme_unsol_ls_handler() to represent the newly received exchange.
Upon error, the out_fail path in the routine unconditionally frees the
pointer, yet subsequently passes the pointer to the abort routine.
Additionally, the abort routine, lpfc_nvme_unsol_ls_issue_abort(), also
has a failure path that will attempt to delete the pointer on error.
Fix these errors by:
- Removing the unconditional free so that it stays valid if passed
to the abort routine.
- Revise the abort routine to not free the pointer. Instead, return
a success/failure status. Note: if success, the later completion of
the abort frees the structure.
- Back in the unsol_ls_handler() error path, if the abort routine was
skipped (thus no possible reference) or the abort routine returned
error, free the pointer.
Fixes: 3a8070c567 ("lpfc: Refactor NVME LS receive handling")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Additional testing encountered null pointers that weren't fully qualified
in lpfc_nvmet_xmt_ls_abort_cmp() and lpfc_nvmet_unsol_issue_abort().
The same error was detected and reported by static checker reporting:
drivers/scsi/lpfc/lpfc_sli.c:2905 lpfc_nvme_unsol_ls_handler()
error: we previously assumed 'phba->targetport' could be null
(see line 2837)
Fix by making phba->nvmet_support and phba->targetport validity checks
in lpfc_nvmet_xmt_ls_abort_cmp() and lpfc_nvmet_unsol_issue_abort().
Fixes: 3a8070c567 (“lpfc: Refactor NVME LS receive handling”)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In order to create or activate a new node, lpfc_els_unsol_buffer() invokes
lpfc_nlp_init() or lpfc_enable_node() or lpfc_nlp_get(), all of them will
return a reference of the specified lpfc_nodelist object to "ndlp" with
increased refcnt.
When lpfc_els_unsol_buffer() returns, local variable "ndlp" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
lpfc_els_unsol_buffer(). When "ndlp" in DEV_LOSS, the function forgets to
decrease the refcnt increased by lpfc_nlp_init() or lpfc_enable_node() or
lpfc_nlp_get(), causing a refcnt leak.
Fix this issue by calling lpfc_nlp_put() when "ndlp" in DEV_LOSS.
Link: https://lore.kernel.org/r/1590416184-52592-1-git-send-email-xiyuyang19@fudan.edu.cn
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The variable rc is being initialized with a value that is never read and it
is being updated later with a new value. The initialization is redundant
and can be removed.
Link: https://lore.kernel.org/r/20200507203111.64709-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unused value")
Now that common helpers exist, add the ability to Send an NVME LS Request
and to Abort an outstanding LS Request to the nvmet side of the driver.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As the nvmet layer does not have the concept of a remoteport object, which
can be used to identify the entity on the other end of the fabric that is
to receive an LS, the hosthandle was introduced. The driver passes the
hosthandle, a value representative of the remote port, with a ls request
receive. The LS request will create the association. The transport will
remember the hosthandle for the association, and if there is a need to
initiate a LS request to the remote port for the association, the
hosthandle will be used. When the driver loses connectivity with the
remote port, it needs to notify the transport that the hosthandle is no
longer valid, allowing the transport to terminate associations related to
the hosthandle.
This patch adds support to the driver for the hosthandle. The driver will
use the ndlp pointer of the remote port for the hosthandle in calls to
nvmet_fc_rcv_ls_req(). The discovery engine is updated to invalidate the
hosthandle whenever connectivity with the remote port is lost.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that common helpers exist, add the ability to receive NVME LS requests
to the driver. New requests will be delivered to the transport by
nvme_fc_rcv_ls_req().
In order to complete the LS, add support for Send LS Response and send
LS response completion handling to the driver.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, the ability to send an NVME LS response is limited to the nvmet
(controller/target) side of the driver. In preparation of both the nvme
and nvmet sides supporting Send LS Response, rework the existing send
ls_rsp and ls_rsp completion routines such that there is common code that
can be used by both sides.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Send LS Abort support is needed when Send LS Request is supported.
Currently, the ability to abort an NVME LS request is limited to the nvme
(host) side of the driver. In preparation of both the nvme and nvmet sides
supporting Send LS Abort, rework the existing ls_req abort routines such
that there is common code that can be used by both sides.
While refactoring it was seen the logic in the abort routine was incorrect.
It attempted to abort all NVME LS's on the indicated port. As such, the
routine was reworked to abort only the NVME LS request that was specified.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, the ability to send an NVME LS request is limited to the nvme
(host) side of the driver. In preparation of both the nvme and nvmet sides
support Send LS Request, rework the existing send ls_req and ls_req
completion routines such that there is common code that can be used by
both sides.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In preparation for supporting both intiator mode and target mode
receiving NVME LS's, commonize the existing NVME LS request receive
handling found in the base driver and in the nvmet side.
Using the original lpfc_nvmet_unsol_ls_event() and
lpfc_nvme_unsol_ls_buffer() routines as a templates, commonize the
reception of an NVME LS request. The common routine will validate the LS
request, that it was received from a logged-in node, and allocate a
lpfc_async_xchg_ctx that is used to manage the LS request. The role of
the port is then inspected to determine which handler is to receive the
LS - nvme or nvmet. As such, the nvmet handler is tied back in. A handler
is created in nvme and is stubbed out.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The last step of commonization is to remove the 'T' suffix from
state and flag field definitions. This is minor, but removes the
mental association that it solely applies to nvmet use.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To support FC-NVME-2 support (actually FC-NVME (rev 1) with Ammendment 1),
both the nvme (host) and nvmet (controller/target) sides will need to be
able to receive LS requests. Currently, this support is in the nvmet side
only. To prepare for both sides supporting LS receive, rename
lpfc_nvmet_rcv_ctx to lpfc_async_xchg_ctx and commonize the definition.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A lot of files in lpfc include nvme headers, building up relationships that
require a file to change for its headers when there is no other change
necessary. It would be better to localize the nvme headers.
There is also no need for separate nvme (initiator) and nvmet (tgt)
header files.
Refactor the inclusion of nvme headers so that all nvme items are
included by lpfc_nvme.h
Merge lpfc_nvmet.h into lpfc_nvme.h so that there is a single header used
by both the nvme and nvmet sides. This prepares for structure sharing
between the two roles. Prep to add shared function prototypes for upcoming
shared routines.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The current LLDD api has:
nvme-fc: contains api for transport to do LS requests (and aborts of
them). However, there is no interface for reception of LS's and sending
responses for them.
nvmet-fc: contains api for transport to do reception of LS's and sending
of responses for them. However, there is no interface for doing LS
requests.
Revise the api's so that both nvme-fc and nvmet-fc can send LS's, as well
as receiving LS's and sending their responses.
Change name of the rcv_ls_req struct to better reflect generic use as
a context to used to send an ls rsp. Specifically:
nvmefc_tgt_ls_req -> nvmefc_ls_rsp
nvmefc_tgt_ls_req.nvmet_fc_private -> nvmefc_ls_rsp.nvme_fc_private
Change nvmet_fc_rcv_ls_req() calling sequence to provide handle that
can be used by transport in later LS request sequences for an association.
nvme-fc nvmet_fc nvme_fcloop:
Revise to adapt to changed names in api header.
Change calling sequence to nvmet_fc_rcv_ls_req() for hosthandle.
Add stubs for new interfaces:
host/fc.c: nvme_fc_rcv_ls_req()
target/fc.c: nvmet_fc_invalidate_host()
lpfc:
Revise to adapt code to changed names in api header.
Change calling sequence to nvmet_fc_rcv_ls_req() for hosthandle.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Update lpfc version to 12.8.0.1
Link: https://lore.kernel.org/r/20200501214310.91713-10-jsmart2021@gmail.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The MDS diagnostic enablement bit for the adapter interface is incorrect in
the driver header.
Correct the bit position for the SET_FEATURE MDS bit.
Link: https://lore.kernel.org/r/20200501214310.91713-9-jsmart2021@gmail.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Running make C=1 M=drivers/scsi/lpfc triggers sparse warnings
Correct the code generating the following errors:
- Incompatible address space assignment without proper conversion.
- Deference of usespace and per-cpu pointers.
Link: https://lore.kernel.org/r/20200501214310.91713-8-jsmart2021@gmail.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In an audit of lockdep calls in the driver, there are multiple lockdep
checks in successive calling layers. E.g. a routine checks, and then calls
a lower routine that also checks, and so on. Calling sequences result in
many redundant checks.
Refine the code to remove lower-level lockdep checks. Update comments on
the lock, correcting a few places where lock object in comment was
incorrect.
Link: https://lore.kernel.org/r/20200501214310.91713-7-jsmart2021@gmail.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
By default, the driver attempts to allocate a hdwq per logical cpu in order
to provide good cpu affinity. Some systems have extremely high cpu counts
and this can significantly raise memory consumption.
In testing on x86 platforms (non-AMD) it is found that sharing of a hdwq by
a physical cpu and its HT cpu can occur with little performance
degredation. By sharing, the hdwq count can be halved, significantly
reducing the memory overhead.
Change the default behavior of the driver on non-AMD x86 platforms to
share a hdwq by the cpu and its HT cpu.
Link: https://lore.kernel.org/r/20200501214310.91713-6-jsmart2021@gmail.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implementation of a previous patch added a condition to an if check that
always end up with the if test being true. Execution of the else clause was
inadvertently negated. The additional condition check was incorrect and
unnecessary after the other modifications had been done in that patch.
Remove the check from the if series.
Link: https://lore.kernel.org/r/20200501214310.91713-5-jsmart2021@gmail.com
Fixes: b95b21193c ("scsi: lpfc: Fix loss of remote port after devloss due to lack of RPIs")
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lldd rebinds the ndlp with rport during a nvme rport registration (via
nvme_fc_register_remoteport). If rport & ndlp pointers are same as the
previous one, the lldd will re-use the ndlp and rport association without
re-initialization. This assumption is incorrect. The lldd should be
ignorant of whether the returned rport pointer is new or not, and should
always assume it is new.
Remove the re-binding code, always assumes that rport pointer received from
transport is a new pointer.
Link: https://lore.kernel.org/r/20200501214310.91713-4-jsmart2021@gmail.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A previous change introduced the atomic use of queue_claimed flag for eq's
and cq's. The code works fine, but the clearing of the queue_claimed flag
is not atomic.
Change queue_claimed = 0 into xchg(&queue_claimed, 0) to be consistent for
change under atomicity.
Link: https://lore.kernel.org/r/20200501214310.91713-3-jsmart2021@gmail.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During code reviews several instances of duplicate module unloading checks
were found.
Remove the duplicate checks.
Link: https://lore.kernel.org/r/20200421203354.49420-1-jsmart2021@gmail.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a batch of changes that didn't make it in the initial pull
request because the lpfc series had to be rebased to redo an incorrect
split. It's basically driver updates to lpfc, target, bnx2fc and ufs
with the rest being minor updates except the sr_block_release one
which fixes a use after free introduced by the removal of the global
mutex in the first patch set.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXpC3hSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishRTaAP9umhxu
8rRnJ5hsxXRmxOUzO5BGe403ffcBeAiEKQ2n3gEAjeoxZAaqKuDDDRfXyRnBpt9Z
QuBrgpm1gdXrJT5DDj4=
=+4Qg
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is a batch of changes that didn't make it in the initial pull
request because the lpfc series had to be rebased to redo an incorrect
split.
It's basically driver updates to lpfc, target, bnx2fc and ufs with the
rest being minor updates except the sr_block_release one which fixes a
use after free introduced by the removal of the global mutex in the
first patch set"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (35 commits)
scsi: core: Add DID_ALLOC_FAILURE and DID_MEDIUM_ERROR to hostbyte_table
scsi: ufs: Use ufshcd_config_pwr_mode() when scaling gear
scsi: bnx2fc: fix boolreturn.cocci warnings
scsi: zfcp: use fallthrough;
scsi: aacraid: do not overwrite retval in aac_reset_adapter()
scsi: sr: Fix sr_block_release()
scsi: aic7xxx: Remove more FreeBSD-specific code
scsi: mpt3sas: Fix kernel panic observed on soft HBA unplug
scsi: ufs: set device as active power mode after resetting device
scsi: iscsi: Report unbind session event when the target has been removed
scsi: lpfc: Change default SCSI LUN QD to 64
scsi: libfc: rport state move to PLOGI if all PRLI retry exhausted
scsi: libfc: If PRLI rejected, move rport to PLOGI state
scsi: bnx2fc: Update the driver version to 2.12.13
scsi: bnx2fc: Fix SCSI command completion after cleanup is posted
scsi: bnx2fc: Process the RQE with CQE in interrupt context
scsi: target: use the stack for XCOPY passthrough cmds
scsi: target: increase XCOPY I/O size
scsi: target: avoid per-loop XCOPY buffer allocations
scsi: target: drop xcopy DISK BLOCK LENGTH debug
...
-----BEGIN PGP SIGNATURE-----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=3woC
-----END PGP SIGNATURE-----
Merge tag 'block-5.7-2020-04-10' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Here's a set of fixes that should go into this merge window. This
contains:
- NVMe pull request from Christoph with various fixes
- Better discard support for loop (Evan)
- Only call ->commit_rqs() if we have queued IO (Keith)
- blkcg offlining fixes (Tejun)
- fix (and fix the fix) for busy partitions"
* tag 'block-5.7-2020-04-10' of git://git.kernel.dk/linux-block:
block: fix busy device checking in blk_drop_partitions again
block: fix busy device checking in blk_drop_partitions
nvmet-rdma: fix double free of rdma queue
blk-mq: don't commit_rqs() if none were queued
nvme-fc: Revert "add module to ops template to allow module references"
nvme: fix deadlock caused by ANA update wrong locking
nvmet-rdma: fix bonding failover possible NULL deref
loop: Better discard support for block devices
loop: Report EOPNOTSUPP properly
nvmet: fix NULL dereference when removing a referral
nvme: inherit stable pages constraint in the mpath stack device
blkcg: don't offline parent blkcg first
blkcg: rename blkcg->cgwb_refcnt to ->online_pin and always use it
nvme-tcp: fix possible crash in recv error flow
nvme-tcp: don't poll a non-live queue
nvme-tcp: fix possible crash in write_zeroes processing
nvmet-fc: fix typo in comment
nvme-rdma: Replace comma with a semicolon
nvme-fcloop: fix deallocation of working context
nvme: fix compat address handling in several ioctls
The original patch was to resolve the lldd being able to be unloaded
while being used to talk to the boot device of the system. However, the
end result of the original patch is that any driver unload while a nvme
controller is live via the lldd is now being prohibited. Given the module
reference, the module teardown routine can't be called, thus there's no
way, other than manual actions to terminate the controllers.
Fixes: 863fbae929 ("nvme_fc: add module to ops template to allow module references")
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----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=deWu
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Revert sysfs "rescan" renames that broke apps (Kelsey Skunberg)
- Add more 32 GT/s link speed decoding and improve the implementation
(Yicong Yang)
Resource management:
- Add support for sizing programmable host bridge apertures and fix a
related alpha Nautilus regression (Ivan Kokshaysky)
Interrupts:
- Add boot interrupt quirk mechanism for Xeon chipsets and document
boot interrupts (Sean V Kelley)
PCIe native device hotplug:
- When possible, disable in-band presence detect and use PDS
(Alexandru Gagniuc)
- Add DMI table for devices that don't use in-band presence detection
but don't advertise that correctly (Stuart Hayes)
- Fix hang when powering slots up/down via sysfs (Lukas Wunner)
- Fix an MSI interrupt race (Stuart Hayes)
Virtualization:
- Add ACS quirks for Zhaoxin devices (Raymond Pang)
Error handling:
- Add Error Disconnect Recover (EDR) support so firmware can report
devices disconnected via DPC and we can try to recover (Kuppuswamy
Sathyanarayanan)
Peer-to-peer DMA:
- Add Intel Sky Lake-E Root Ports B, C, D to the whitelist (Andrew
Maier)
ASPM:
- Reduce severity of common clock config message (Chris Packham)
- Clear the correct bits when enabling L1 substates, so we don't go
to the wrong state (Yicong Yang)
Endpoint framework:
- Replace EPF linkup ops with notifier call chain and improve locking
(Kishon Vijay Abraham I)
- Fix concurrent memory allocation in OB address region (Kishon Vijay
Abraham I)
- Move PF function number assignment to EPC core to support multiple
function creation methods (Kishon Vijay Abraham I)
- Fix issue with clearing configfs "start" entry (Kunihiko Hayashi)
- Fix issue with endpoint MSI-X ignoring BAR Indicator and Table
Offset (Kishon Vijay Abraham I)
- Add support for testing DMA transfers (Kishon Vijay Abraham I)
- Add support for testing > 10 endpoint devices (Kishon Vijay Abraham I)
- Add support for tests to clear IRQ (Kishon Vijay Abraham I)
- Add common DT schema for endpoint controllers (Kishon Vijay Abraham I)
Amlogic Meson PCIe controller driver:
- Add DT bindings for AXG PCIe PHY, shared MIPI/PCIe analog PHY (Remi
Pommarel)
- Add Amlogic AXG PCIe PHY, AXG MIPI/PCIe analog PHY drivers (Remi
Pommarel)
Cadence PCIe controller driver:
- Add Root Complex/Endpoint DT schema for Cadence PCIe (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Add two VMD Device IDs that require bus restriction mode (Sushma
Kalakota)
Mobiveil PCIe controller driver:
- Refactor and modularize mobiveil driver (Hou Zhiqiang)
- Add support for Mobiveil GPEX Gen4 host (Hou Zhiqiang)
Microsoft Hyper-V host bridge driver:
- Add support for Hyper-V PCI protocol version 1.3 and
PCI_BUS_RELATIONS2 (Long Li)
- Refactor to prepare for virtual PCI on non-x86 architectures (Boqun
Feng)
- Fix memory leak in hv_pci_probe()'s error path (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Use pci_parse_request_of_pci_ranges() (Rob Herring)
- Add support for endpoint mode and related DT updates (Vidya Sagar)
- Reduce -EPROBE_DEFER error message log level (Thierry Reding)
Qualcomm PCIe controller driver:
- Restrict class fixup to specific Qualcomm devices (Bjorn Andersson)
Synopsys DesignWare PCIe controller driver:
- Refactor core initialization code for endpoint mode (Vidya Sagar)
- Fix endpoint MSI-X to use correct table address (Kishon Vijay
Abraham I)
TI DRA7xx PCIe controller driver:
- Fix MSI IRQ handling (Vignesh Raghavendra)
TI Keystone PCIe controller driver:
- Allow AM654 endpoint to raise MSI-X interrupt (Kishon Vijay Abraham I)
Miscellaneous:
- Quirk ASMedia XHCI USB to avoid "PME# from D0" defect (Kai-Heng
Feng)
- Use ioremap(), not phys_to_virt(), for platform ROM to fix video
ROM mapping with CONFIG_HIGHMEM (Mikel Rychliski)"
* tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (96 commits)
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
PCI: sysfs: Revert "rescan" file renames
...
The default lun queue depth by the driver has been 30 for many years.
However, this value, when used with more recent hardware, has actually
throttled some tests that concentrate io on a lun.
Increase the default lun queue depth to 64.
Queue full handling, reported by the target, remains in effect and
unchanged.
Link: https://lore.kernel.org/r/20200323161935.40341-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During code review, identified dss feature that was a prototype only and
was never productized in SLI3. They shouldn't be there and prevents reuse
of the command areas.
Remove any code in the driver to deal with dss, including code to deal with
fips, which is associated with the dss feature.
Link: https://lore.kernel.org/r/20200322181304.37655-12-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently driver ktime stats, measuring code paths, is NVME-specific.
Convert the stats routines such that the code paths are generic, providing
status for NVME and SCSI. Added ktime stat calls in SCSI queuecommand and
cmpl routines.
Link: https://lore.kernel.org/r/20200322181304.37655-11-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The cpu io statistics were capped by a hard define limit of 128. This
effectively was a max number of CPUs, not an actual CPU count, nor actual
CPU numbers which can be even larger than both of those values. This made
stats off/misleading and on large CPU count systems, wrong.
Fix the stats so that all CPUs can have a stats struct. Fix the looping
such that it loops by hdwq, finds CPUs that used the hdwq, and sum the
stats, then display.
Link: https://lore.kernel.org/r/20200322181304.37655-9-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The AER interfaces to clear error status registers were a confusing mess:
- pci_cleanup_aer_uncorrect_error_status() cleared non-fatal errors
from the Uncorrectable Error Status register.
- pci_aer_clear_fatal_status() cleared fatal errors from the
Uncorrectable Error Status register.
- pci_cleanup_aer_error_status_regs() cleared the Root Error Status
register (for Root Ports), the Uncorrectable Error Status register,
and the Correctable Error Status register.
Rename them to make them consistent:
From To
---------------------------------------- -------------------------------
pci_cleanup_aer_uncorrect_error_status() pci_aer_clear_nonfatal_status()
pci_aer_clear_fatal_status() pci_aer_clear_fatal_status()
pci_cleanup_aer_error_status_regs() pci_aer_clear_status()
Since pci_cleanup_aer_error_status_regs() (renamed to
pci_aer_clear_status()) is only used within drivers/pci/, move the
declaration from <linux/aer.h> to drivers/pci/pci.h.
[bhelgaas: commit log, add renames]
Link: https://lore.kernel.org/r/d1310a75dc3d28f7e8da4e99c45fbd3e60fe238e.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Kernel is crashing with the following stacktrace:
BUG: unable to handle kernel NULL pointer dereference at
00000000000005bc
IP: lpfc_nvme_register_port+0x1a8/0x3a0 [lpfc]
...
Call Trace:
lpfc_nlp_state_cleanup+0x2b2/0x500 [lpfc]
lpfc_nlp_set_state+0xd7/0x1a0 [lpfc]
lpfc_cmpl_prli_prli_issue+0x1f7/0x450 [lpfc]
lpfc_disc_state_machine+0x7a/0x1e0 [lpfc]
lpfc_cmpl_els_prli+0x16f/0x1e0 [lpfc]
lpfc_sli_sp_handle_rspiocb+0x5b2/0x690 [lpfc]
lpfc_sli_handle_slow_ring_event_s4+0x182/0x230 [lpfc]
lpfc_do_work+0x87f/0x1570 [lpfc]
kthread+0x10d/0x130
ret_from_fork+0x35/0x40
During target side fault injections, it is possible to hit the
NLP_WAIT_FOR_UNREG case in lpfc_nvme_remoteport_delete. A prior commit
fixed a rebind and delete race condition, but called lpfc_nlp_put
unconditionally. This triggered a deletion and the crash.
Fix by movng nlp_put to inside the NLP_WAIT_FOR_UNREG case, where the nlp
will be being unregistered/removed. Leave the reference if the flag isn't
set.
Link: https://lore.kernel.org/r/20200322181304.37655-8-jsmart2021@gmail.com
Fixes: b15bd3e621 ("scsi: lpfc: Fix nvme remoteport registration race conditions")
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc_sli4_wq_release() routine iterates for each interim value when
updating the wq consuemr index. This wastes cycles and possibly confuses
things as thevalue itterates (and the modulo logic is being applied).
There's no reason for this. Just set it to the value from the hw.
Link: https://lore.kernel.org/r/20200322181304.37655-7-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Injecting EEH on a 32GB card is causing kernel oops
The pci error handler is doing an IO flush and the offline code is also
doing an IO flush. When the 1st flush is complete the hdwq is destroyed
(freed), yet the second flush accesses the hdwq and crashes.
Added a check in lpfc_sli4_fush_io_rings to check both the HBA_IOQ_FLUSH
flag and the hdwq pointer to see if it is already set and not already
freed.
Link: https://lore.kernel.org/r/20200322181304.37655-6-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SCSI layer sends driver IOs with more s/g segments than driver can handle.
This results in "Too many sg segments from dma_map_sg. Config 64, seg_cnt
219" error messages from the lpfc_scsi_prep_dma_buf_s3() routine.
The was due to use the driver using individual templates for pport and
vport, host reset enabled or not, nvme vs scsi, etc. In the end, there was
a combination for a vport that didn't match the pport.
Rather than enumerating more templates and more discretionary assignments,
revert to a base template that is copied to a template specific to the
pport/vport. Then, based on role, attributes and sli type, modify the
fields that are different for that port. Added a log message to
lpfc_create_port to validate values.
Link: https://lore.kernel.org/r/20200322181304.37655-5-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In lpfc_nvmet_prep_fcp_wqe() the line "rsp->sg_cnt = 0" is modifying the
transport's data structure. This may result in the transport believing the
s/g list was already freed, thus may not unmap/free it properly. Lpfc
driver should not modify the transport data structure.
The zeroing of the sg_cnt is to avoid use of the transport's sgl in a
subsequent loop where the driver builds the necessary requests for the
adapter firmware to complete the IO.
Change LLDD to use a local copy of the transport sg_cnt when building
requests to be passed to the adapter fw.
Link: https://lore.kernel.org/r/20200322181304.37655-4-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following lockdep error was reported when unloading the lpfc driver:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
...
Call Trace:
dump_stack+0x96/0xe0
register_lock_class+0x8b8/0x8c0
? lockdep_hardirqs_on+0x190/0x280
? is_dynamic_key+0x150/0x150
? wait_for_completion_interruptible+0x2a0/0x2a0
? wake_up_q+0xd0/0xd0
__lock_acquire+0xda/0x21a0
? register_lock_class+0x8c0/0x8c0
? synchronize_rcu_expedited+0x500/0x500
? __call_rcu+0x850/0x850
lock_acquire+0xf3/0x1f0
? del_timer_sync+0x5/0xb0
del_timer_sync+0x3c/0xb0
? del_timer_sync+0x5/0xb0
lpfc_pci_remove_one.cold.102+0x8b7/0x935 [lpfc]
...
Unloading the driver resulted in a call to del_timer_sync for the
cpuhp_poll_timer. However the call to setup the timer had never been made,
so the timer structures used by lockdep checking were not initialized.
Unconditionally call setup_timer for the cpuhp_poll_timer during driver
initialization. Calls to start the timer remain "as needed".
Link: https://lore.kernel.org/r/20200322181304.37655-3-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following kasan bug was called out:
BUG: KASAN: slab-out-of-bounds in lpfc_unreg_login+0x7c/0xc0 [lpfc]
Read of size 2 at addr ffff889fc7c50a22 by task lpfc_worker_3/6676
...
Call Trace:
dump_stack+0x96/0xe0
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
print_address_description.constprop.6+0x1b/0x220
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
__kasan_report.cold.9+0x37/0x7c
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
kasan_report+0xe/0x20
lpfc_unreg_login+0x7c/0xc0 [lpfc]
lpfc_sli_def_mbox_cmpl+0x334/0x430 [lpfc]
...
When processing the completion of a "Reg Rpi" login mailbox command in
lpfc_sli_def_mbox_cmpl, a call may be made to lpfc_unreg_login. The vpi is
extracted from the completing mailbox context and passed as an input for
the next. However, the vpi stored in the mailbox command context is an
absolute vpi, which for SLI4 represents both base + offset. When used with
a non-zero base component, (function id > 0) this results in an
out-of-range access beyond the allocated phba->vpi_ids array.
Fix by subtracting the function's base value to get an accurate vpi number.
Link: https://lore.kernel.org/r/20200322181304.37655-2-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a spelling mistake in a lpfc_printf_vlog info message. Fix it.
[mkp: fix spelling mistake in commit description]
Link: https://lore.kernel.org/linux-scsi/20200221154841.77791-1-colin.king@canonical.com
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch modifies lpfc to register for Link Integrity events via the use
of an RDF ELS and to perform Link Integrity FPIN logging.
Specifically, the driver was modified to:
- Format and issue the RDF ELS immediately following SCR registration.
This registers the ability of the driver to receive FPIN ELS.
- Adds decoding of the FPIN els into the received descriptors, with
logging of the Link Integrity event information. After decoding, the ELS
is delivered to the scsi fc transport to be delivered to any user-space
applications.
- To aid in logging, simple helpers were added to create enum to name
string lookup functions that utilize the initialization helpers from the
fc_els.h header.
- Note: base header definitions for the ELS's don't populate the
descriptor payloads. As such, lpfc creates it's own version of the
structures, using the base definitions (mostly headers) and additionally
declaring the descriptors that will complete the population of the ELS.
Link: https://lore.kernel.org/r/20200210173155.547-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update copyrights to 2020 for files modified in the 12.6.0.4 patch set.
Link: https://lore.kernel.org/r/20200128002312.16346-13-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current code does some odd +1 over maximum xri count checks and
requires that the lun_queue_count can't be bigger than maximum xri count
divided by 8. These items are bogus.
Clean the code up to cap lun_queue_count to maximum xri count.
Link: https://lore.kernel.org/r/20200128002312.16346-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There was report of an odd "Fix me..." log message, which was tracked down
to the lpfc_els_rcv_rps() routine. This was in handling of a very old and
obsolete ELS - Read Port Status. The RPS ELS was defined in FC-LS-1, but
deprecated in FC-LS-2, and removed from all later FC-LS revisions. It was
replaced by the Read Diagnostic Parameters (RDP) ELS and the Link Error
Status Block descriptor.
There should be no support for the RSP ELS. Remove support from driver.
Link: https://lore.kernel.org/r/20200128002312.16346-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity reported a memory corruption error for the fdmi attributes
routines:
CID 15768 [Memory Corruption] Out-of-bounds access on FDMI
Sloppy coding of the fmdi structures. In both the lpfc_fdmi_attr_def and
lpfc_fdmi_reg_port_list structures, a field was placed at the start of
payload that may have variable content. The field was given an arbitrary
type (uint32_t). The code then uses the field name to derive an address,
which it used in things such as memset and memcpy. The memset sizes or
memcpy lengths were larger than the arbitrary type, thus coverity reported
an error.
Fix by replacing the arbitrary fields with the real field structures
describing the payload.
Link: https://lore.kernel.org/r/20200128002312.16346-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following error is see from the compiler:
drivers/scsi/lpfc/lpfc_init.c: In function
‘lpfc_cpuhp_get_eq’: drivers/scsi/lpfc/lpfc_init.c:12660:1:
error: the frame size of 1032 bytes is larger than 1024 bytes
[-Werror=frame-larger-than=]
The issue is due to allocating a cpumask on the stack.
Fix by converting to a dynamical allocation of the cpu mask.
Link: https://lore.kernel.org/r/20200128002312.16346-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When performing reset testing, the eq's list for related hwqs was getting
corrupted. In cases where there is not a 1:1 eq to hwq, the eq is
shared. The eq maintains a list of hwqs utilizing it in case of cpu
offlining and polling. During the reset, the hwqs are being torn down so
they can be recreated. The recreation was getting confused by seeing a
non-null eq assignment on the eq and the eq list became corrupt.
Correct by clearing the hdwq eq assignment when the hwq is cleaned up.
Link: https://lore.kernel.org/r/20200128002312.16346-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adjust FC4 Types in FDMI settings
The driver sets FDMI information registring ELS as a FC4 type. ELS is a
fc3 type and should not be registered.
Fix by removing ELS type bit when we register for FDMI Port attributes.
Link: https://lore.kernel.org/r/20200128002312.16346-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driver is set to enable bb credit recovery, the switch displayed the
setting as inactive. If the link bounces, it switches to Active.
During link up processing, the driver currently does a MBX_READ_SPARAM
followed by a MBX_CONFIG_LINK. These mbox commands are queued to be
executed, one at a time and the completion is processed by the worker
thread. Since the MBX_READ_SPARAM is done BEFORE the MBX_CONFIG_LINK, the
BB_SC_N bit is never set the the returned values. BB Credit recovery status
only gets set after the driver requests the feature in CONFIG_LINK, which
is done after the link up. Thus the ordering of READ_SPARAM needs to follow
the CONFIG_LINK.
Fix by reordering so that READ_SPARAM is done after CONFIG_LINK. Added a
HBA_DEFER_FLOGI flag so that any FLOGI handling waits until after the
READ_SPARAM is done so that the proper BB credit value is set in the FLOGI
payload.
Fixes: 6bfb162082 ("scsi: lpfc: Fix configuration of BB credit recovery in service parameters")
Cc: <stable@vger.kernel.org> # v5.4+
Link: https://lore.kernel.org/r/20200128002312.16346-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a call to lpfc_get_cmd_rsp_buf_per_hdwq returns NULL (memory allocation
failure), a previously allocated lpfc_io_buf resource is leaked.
Fix by releasing the lpfc_io_buf resource in the failure path.
Fixes: d79c9e9d4b ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.")
Cc: <stable@vger.kernel.org> # v5.4+
Link: https://lore.kernel.org/r/20200128002312.16346-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is occasionally seeing the following SLI Port error, requiring
reset and reinit:
Port Status Event: ... error 1=0x52004a01, error 2=0x218
The failure means an RQ timeout. That is, the adapter had received
asynchronous receive frames, ran out of buffer slots to place the frames,
and the driver did not replenish the buffer slots before a timeout
occurred. The driver should not be so slow in replenishing buffers that a
timeout can occur.
When the driver received all the frames of a sequence, it allocates an IOCB
to put the frames in. In a situation where there was no IOCB available for
the frame of a sequence, the RQ buffer corresponding to the first frame of
the sequence was not returned to the FW. Eventually, with enough traffic
encountering the situation, the timeout occurred.
Fix by releasing the buffer back to firmware whenever there is no IOCB for
the first frame.
[mkp: typo]
Link: https://lore.kernel.org/r/20200128002312.16346-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warning:
drivers/scsi/lpfc/lpfc_nportdisc.c:344:1: warning:
symbol 'lpfc_defer_acc_rsp' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20200107014956.41748-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series concludes the work I did for linux-5.5 on the compat_ioctl()
cleanup, killing off fs/compat_ioctl.c and block/compat_ioctl.c by moving
everything into drivers.
Overall this would be a reduction both in complexity and line count, but
as I'm also adding documentation the overall number of lines increases
in the end.
My plan was originally to keep the SCSI and block parts separate.
This did not work easily because of interdependencies: I cannot
do the final SCSI cleanup in a good way without first addressing the
CDROM ioctls, so this is one series that I hope could be merged through
either the block or the scsi git trees, or possibly both if you can
pull in the same branch.
The series comes in these steps:
1. clean up the sg v3 interface as suggested by Linus. I have
talked about this with Doug Gilbert as well, and he would
rebase his sg v4 patches on top of "compat: scsi: sg: fix v3
compat read/write interface"
2. Actually moving handlers out of block/compat_ioctl.c and
block/scsi_ioctl.c into drivers, mixed in with cleanup
patches
3. Document how to do this right. I keep getting asked about this,
and it helps to point to some documentation file.
The branch is based on another one that fixes a couple of bugs found
during the creation of this series.
Changes since v3:
https://lore.kernel.org/lkml/20200102145552.1853992-1-arnd@arndb.de/
- Move sr_compat_ioctl fixup to correct patch (Ben Hutchings)
- Add Reviewed-by tags
Changes since v2:
https://lore.kernel.org/lkml/20191217221708.3730997-1-arnd@arndb.de/
- Rebase to v5.5-rc4, which contains the earlier bugfixes
- Fix sr_block_compat_ioctl() error handling bug found by
Ben Hutchings
- Fix idecd_locked_compat_ioctl() compat_ptr() bug
- Don't try to handle HDIO_DRIVE_TASKFILE in drivers/ide
- More documentation improvements
Changes since v1:
https://lore.kernel.org/lkml/20191211204306.1207817-1-arnd@arndb.de/
- move out the bugfixes into a branch for itself
- clean up scsi sg driver further as suggested by Christoph Hellwig
- avoid some ifdefs by moving compat_ptr() out of asm/compat.h
- split out the blkdev_compat_ptr_ioctl function; bug spotted by
Ben Hutchings
- Improve formatting of documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cddL
-----END PGP SIGNATURE-----
Merge tag 'block-ioctl-cleanup-5.6' into 5.6/scsi-queue
Pull compat_ioctl cleanup from Arnd. Here's his description:
This series concludes the work I did for linux-5.5 on the compat_ioctl()
cleanup, killing off fs/compat_ioctl.c and block/compat_ioctl.c by moving
everything into drivers.
Overall this would be a reduction both in complexity and line count, but
as I'm also adding documentation the overall number of lines increases
in the end.
My plan was originally to keep the SCSI and block parts separate.
This did not work easily because of interdependencies: I cannot
do the final SCSI cleanup in a good way without first addressing the
CDROM ioctls, so this is one series that I hope could be merged through
either the block or the scsi git trees, or possibly both if you can
pull in the same branch.
The series comes in these steps:
1. clean up the sg v3 interface as suggested by Linus. I have
talked about this with Doug Gilbert as well, and he would
rebase his sg v4 patches on top of "compat: scsi: sg: fix v3
compat read/write interface"
2. Actually moving handlers out of block/compat_ioctl.c and
block/scsi_ioctl.c into drivers, mixed in with cleanup
patches
3. Document how to do this right. I keep getting asked about this,
and it helps to point to some documentation file.
The branch is based on another one that fixes a couple of bugs found
during the creation of this series.
Changes since v3:
https://lore.kernel.org/lkml/20200102145552.1853992-1-arnd@arndb.de/
- Move sr_compat_ioctl fixup to correct patch (Ben Hutchings)
- Add Reviewed-by tags
Changes since v2:
https://lore.kernel.org/lkml/20191217221708.3730997-1-arnd@arndb.de/
- Rebase to v5.5-rc4, which contains the earlier bugfixes
- Fix sr_block_compat_ioctl() error handling bug found by
Ben Hutchings
- Fix idecd_locked_compat_ioctl() compat_ptr() bug
- Don't try to handle HDIO_DRIVE_TASKFILE in drivers/ide
- More documentation improvements
Changes since v1:
https://lore.kernel.org/lkml/20191211204306.1207817-1-arnd@arndb.de/
- move out the bugfixes into a branch for itself
- clean up scsi sg driver further as suggested by Christoph Hellwig
- avoid some ifdefs by moving compat_ptr() out of asm/compat.h
- split out the blkdev_compat_ptr_ioctl function; bug spotted by
Ben Hutchings
- Improve formatting of documentation
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Four fixes and one spelling update, all in drivers: 2 in lpfc and the
rest in mp3sas, cxgbi and target.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXgaIWSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishb2SAP45hS5T
owI8lIt+jMBnYG3k/66EleVdqMOcvtm9ewDN2gD/eW1LBz6uPzPn07gLB3V4TTTZ
rI8lfohhWJwRAHjvL8A=
=nxXW
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four fixes and one spelling update, all in drivers: two in lpfc and
the rest in mp3sas, cxgbi and target"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target/iblock: Fix protection error with blocks greater than 512B
scsi: libcxgbi: fix NULL pointer dereference in cxgbi_device_destroy()
scsi: lpfc: fix spelling mistakes of asynchronous
scsi: lpfc: fix build failure with DEBUGFS disabled
scsi: mpt3sas: Fix double free in attach error handling
Current driver code looks at iocb types and uses a "==" comparison on the
flags to determine type. If another flag were set, it would disrupt the
comparison.
Fix by converting to a bitwise & operation.
Link: https://lore.kernel.org/r/20191218235808.31922-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When running Cisco-MDS diagnostics which perform driver-level frame loop
back, the switch is reporting errors. Diagnostic has a limit on latency
that is not being met by the driver.
The requirement of Latency frames is that they should be responded back by
the host with a maximum delay of few hundreds of microseconds. If the
switch doesn't get response frames within this time frame, it fails the
test.
Test is failing as the lpfc-wq workqueue was overwhelmed by the packet rate
and in some cases, the work element yielded to other kernel elements.
To resolve, reduce the outstanding load allowed by the adapter. This
ensures the driver spends a reasonable amount of time doing loopback and
can do so such that latency values can be met. Load is managed by reducing
the number of receive buffers posted such that the link can be
backpressured to reduce load.
Link: https://lore.kernel.org/r/20191218235808.31922-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unattaching, the driver did not unmap the DPP bar. This caused the
next load of the driver, which attempts to enable wc, to not work correctly
and wc to be disabled due to an address mapping overlap.
Fix by unmapping on unattach.
Link: https://lore.kernel.org/r/20191218235808.31922-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The order of the flags/checks for adapters where FC-AL is supported
erroneously excluded lpe35000 adapter models. Also noted that the G7 flags
for Loop and Persistent topology are incorrect. They should follow the
rules as G6.
Rework the logic to enable LPe35000 FC-AL support. Collapse G7 support
logic to the same rules as G6.
Link: https://lore.kernel.org/r/20191218235808.31922-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
/sys/kernel/debug/lpfc/fn0/ras_log always shows the same ras_log even if
there are link bounce events triggered via issue_lip
Dynamic FW logging had logic that prematurely breaks from the buffer
filling loop.
Fix the check for buffer overrun by looking before copying and restricting
copy length to the remaining buffer. When copying, ensure space for NULL
character is left in the buffer. While in the routine - ensure the buffer
is cleared before adding elements.
Link: https://lore.kernel.org/r/20191218235808.31922-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are reports of multiple ports on the same system displaying different
hostnames in fabric FDMI displays.
Currently, the driver registers the hostname at initialization and obtains
the hostname via init_utsname()->nodename queried at the time the FC link
comes up. Unfortunately, if the machine hostname is updated after
initialization, such as via DHCP or admin command, the value registered
initially will be incorrect.
Fix by having the driver save the hostname that was registered with FDMI.
The driver then runs a heartbeat action that will check the hostname. If
the name changes, reregister the FMDI data.
The hostname is used in RSNN_NN, FDMI RPA and FDMI RHBA.
Link: https://lore.kernel.org/r/20191218235808.31922-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the WriteObject mailbox response has change_status set to is 0x2
(Firmware Reset) or 0x04 (Port Migration Reset), the CSF field should also
be checked to see if a fw reset is sufficient to enable all new features in
the updated firmware image. If not, a fw reset would start the new
firmware, but with a feature level equal to existing firmware. To enable
the new features, a chip reset/pci slot reset would be required.
Check the CSF bit when change_status is 0x2 or 0x4 to know whether to
perform a pci bus reset or fw reset.
Link: https://lore.kernel.org/r/20191218235808.31922-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch reworks the fdmi symbolic node name data for the following two
issues:
- Correcting extraneous periods following the DV and HN fdmi data fields.
- Avoiding buffer overflow issues when formatting the data.
The fix to the fist issue is to just remove the characters.
The fix to the second issue has all data being staged in temporary storage
before being moved to the real buffer.
Link: https://lore.kernel.org/r/20191218235808.31922-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVMe device re-discovery does not complete. Dev_loss_tmo messages seen on
initiator after recovery from a link disturbance.
The failing case is the following:
When the driver (as a NVME target) receives a PLOGI, the driver initiates
an "unreg rpi" mailbox command. While the mailbox command is in progress,
the driver requests that an ACC be sent to the initiator. The target's ACC
is received by the initiator and the initiator then transmits a PLOGI. The
driver receives the PLOGI prior to receiving the completion for the PLOGI
response WQE that sent the ACC. (Different delivery sources from the hw so
the race is very possible). Given the PLOGI is prior to the ACC completion
(signifying PLOGI exchange complete), the driver LS_RJT's the PRLI. The
"unreg rpi" mailbox then completes. Since PRLI has been received, the
driver transmits a PLOGI to restart discovery, which the initiator then
ACC's. If the driver processes the (re)PLOGI ACC prior to the completing
the handling for the earlier ACC it sent the intiators original PLOGI,
there is no state change for completion of the (re)PLOGI. The ndlp remains
in "PLOGI Sent" and the initiator continues sending PRLI's which are
rejected by the target until timeout or retry is reached.
Fix by: When in target mode, defer sending an ACC for the received PLOGI
until unreg RPI completes.
Link: https://lore.kernel.org/r/20191218235808.31922-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are spelling mistakes of asynchronous in a lpfc_printf_log message
and comments. Fix these.
Link: https://lore.kernel.org/r/20191218084301.627555-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent change appears to have moved an #endif by accident:
drivers/scsi/lpfc/lpfc_debugfs.c:5393:18: error: 'lpfc_debugfs_dumpHBASlim_open' undeclared here (not in a function); did you mean 'lpfc_debugfs_op_dumpHBASlim'?
drivers/scsi/lpfc/lpfc_debugfs.c:5394:18: error: 'lpfc_debugfs_lseek' undeclared here (not in a function); did you mean 'lpfc_debugfs_nvme_trc'?
drivers/scsi/lpfc/lpfc_debugfs.c:5395:18: error: 'lpfc_debugfs_read' undeclared here (not in a function); did you mean 'lpfc_debug_dump_q'?
drivers/scsi/lpfc/lpfc_debugfs.c:5396:18: error: 'lpfc_debugfs_release' undeclared here (not in a function); did you mean 'lpfc_debugfs_terminate'?
drivers/scsi/lpfc/lpfc_debugfs.c:5402:18: error: 'lpfc_debugfs_dumpHostSlim_open' undeclared here (not in a function); did you mean 'lpfc_debugfs_op_dumpHostSlim'?
Move it back to where it was previously.
Fixes: 95bfc6d8ad ("scsi: lpfc: Make FW logging dynamically configurable")
Link: https://lore.kernel.org/r/20191216131701.3125077-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
24 fixes, all in drivers. The lion's share (16) are qla2xxx and the
rest are iscsi (3), ufs (2), smarpqi, lpfc and libsas.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXfUGbSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishRNxAP4zxu9A
93AijCfJaMhtuzh2bdegf1IC/LXhbu69CQm9bgD+OeQLR9XvopjRBsQC35W1Im5T
73K+w8YTyddZEkOvcio=
=m0Xq
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"24 fixes, all in drivers. The lion's share (16) are qla2xxx and the
rest are iscsi (3), ufs (2), smarpqi, lpfc and libsas"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: iscsi: Avoid potential deadlock in iscsi_if_rx func
scsi: iscsi: Fix a potential deadlock in the timeout handler
scsi: smartpqi: Update attribute name to `driver_version`
scsi: libsas: stop discovering if oob mode is disconnected
scsi: ufs: Disable autohibern8 feature in Cadence UFS
scsi: iscsi: qla4xxx: fix double free in probe
scsi: ufs: Give an unique ID to each ufs-bsg
scsi: qla2xxx: Add debug dump of LOGO payload and ELS IOCB
scsi: qla2xxx: Ignore PORT UPDATE after N2N PLOGI
scsi: qla2xxx: Don't defer relogin unconditonally
scsi: qla2xxx: Send Notify ACK after N2N PLOGI
scsi: qla2xxx: Configure local loop for N2N target
scsi: qla2xxx: Fix PLOGI payload and ELS IOCB dump length
scsi: qla2xxx: Don't call qlt_async_event twice
scsi: qla2xxx: Allow PLOGI in target mode
scsi: qla2xxx: Change discovery state before PLOGI
scsi: qla2xxx: Drop superfluous INIT_WORK of del_work
scsi: qla2xxx: Initialize free_work before flushing it
scsi: qla2xxx: Use explicit LOGO in target mode
scsi: qla2xxx: Ignore NULL pointer in tcm_qla2xxx_free_mcmd
...
-----BEGIN PGP SIGNATURE-----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=hmxJ
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20191212' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- stable fix for the bi_size overflow. Not a corruption issue, but a
case wher we could merge but disallowed (Andreas)
- NVMe pull request via Keith, with various fixes.
- MD pull request from Song.
- Merge window regression fix for the rq passthrough stats (Logan)
- Remove unused blkcg_drain_queue() function (Guoqing)
* tag 'for-linus-20191212' of git://git.kernel.dk/linux-block:
blk-cgroup: remove blkcg_drain_queue
block: fix NULL pointer dereference in account statistics with IDE
md: make sure desc_nr less than MD_SB_DISKS
md: raid1: check rdev before reference in raid1_sync_request func
raid5: need to set STRIPE_HANDLE for batch head
block: fix "check bi_size overflow before merge"
nvme/pci: Fix read queue count
nvme/pci Limit write queue sizes to possible cpus
nvme/pci: Fix write and poll queue types
nvme/pci: Remove last_cq_head
nvme: Namepace identification descriptor list is optional
nvme-fc: fix double-free scenarios on hw queues
nvme: else following return is not needed
nvme: add error message on mismatching controller ids
nvme_fc: add module to ops template to allow module references
nvmet-loop: Avoid preallocating big SGL for data
nvme-fc: Avoid preallocating big SGL for data
nvme-rdma: Avoid preallocating big SGL for data
When phba->mbox_ext_buf_ctx.seqNum != phba->mbox_ext_buf_ctx.numBuf,
dd_data should be freed before return SLI_CONFIG_HANDLED.
When lpfc_sli_issue_mbox func return fails, pmboxq should be also freed in
job_error tag.
Link: https://lore.kernel.org/r/EDBAAA0BBBA2AC4E9C8B6B81DEEE1D6915E7A966@DGGEML525-MBS.china.huawei.com
Signed-off-by: Bo Wu <wubo40@huawei.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
11 patches, all in drivers (no core changes) that are either minor
cleanups or small fixes. They were late arriving, but still safe for
-rc1.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXeyDEiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbijAQDIuM45
xeEXgWXF8c/tYuvildK1WjyVzwBO2k563lUmYQEA4rxSzkmhtcaMTDuk4hI4Y4TP
p87U1bXNSJ7tCpFU15w=
=W43H
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Eleven patches, all in drivers (no core changes) that are either minor
cleanups or small fixes.
They were late arriving, but still safe for -rc1"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
scsi: megaraid_sas: Make poll_aen_lock static
scsi: sd_zbc: Improve report zones error printout
scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
scsi: qla2xxx: unregister ports after GPN_FT failure
scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
scsi: pm80xx: Remove unused include of linux/version.h
scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
scsi: scsi_transport_sas: Fix memory leak when removing devices
scsi: lpfc: size cpu map by last cpu id set
scsi: ibmvscsi_tgt: Remove unneeded variable rc
This is mostly update of the usual drivers: aacraid, ufs, zfcp,
NCR5380, lpfc, qla2xxx, smartpqi, hisi_sas, target, mpt3sas, pm80xx
plus a whole load of minor updates and fixes. The two major core
changes are Al Viro's reworking of sg's handling of copy to/from user,
Ming Lei's removal of the host busy counter to avoid contention in the
multiqueue case and Damien Le Moal's fixing of residual tracking
across error handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXeKvHCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQJMAQDAjlAi
SNfbyndMqyf+rZGWufDI+43Up1VvW9GeWJHeDwEAxfO5XZsCks2uT8UxXhpEp9L7
HkiUww3zbcgl0FWFkUM=
=cdVU
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: aacraid, ufs, zfcp,
NCR5380, lpfc, qla2xxx, smartpqi, hisi_sas, target, mpt3sas, pm80xx
plus a whole load of minor updates and fixes.
The major core changes are Al Viro's reworking of sg's handling of
copy to/from user, Ming Lei's removal of the host busy counter to
avoid contention in the multiqueue case and Damien Le Moal's fixing of
residual tracking across error handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (251 commits)
scsi: bnx2fc: timeout calculation invalid for bnx2fc_eh_abort()
scsi: target: core: Fix a pr_debug() argument
scsi: iscsi: Don't send data to unbound connection
scsi: target: iscsi: Wait for all commands to finish before freeing a session
scsi: target: core: Release SPC-2 reservations when closing a session
scsi: target: core: Document target_cmd_size_check()
scsi: bnx2i: fix potential use after free
Revert "scsi: qla2xxx: Fix memory leak when sending I/O fails"
scsi: NCR5380: Add disconnect_mask module parameter
scsi: NCR5380: Unconditionally clear ICR after do_abort()
scsi: NCR5380: Call scsi_set_resid() on command completion
scsi: scsi_debug: num_tgts must be >= 0
scsi: lpfc: use hdwq assigned cpu for allocation
scsi: arcmsr: fix indentation issues
scsi: qla4xxx: fix double free bug
scsi: pm80xx: Modified the logic to collect fatal dump
scsi: pm80xx: Tie the interrupt name to the module instance
scsi: pm80xx: Controller fatal error through sysfs
scsi: pm80xx: Do not request 12G sas speeds
scsi: pm80xx: Cleanup command when a reset times out
...
In nvme-fc: it's possible to have connected active controllers
and as no references are taken on the LLDD, the LLDD can be
unloaded. The controller would enter a reconnect state and as
long as the LLDD resumed within the reconnect timeout, the
controller would resume. But if a namespace on the controller
is the root device, allowing the driver to unload can be problematic.
To reload the driver, it may require new io to the boot device,
and as it's no longer connected we get into a catch-22 that
eventually fails, and the system locks up.
Fix this issue by taking a module reference for every connected
controller (which is what the core layer did to the transport
module). Reference is cleared when the controller is removed.
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Currently the lpfc driver sizes its cpu_map array based on
num_possible_cpus(). However, that can be a value that is less than the
highest cpu id bit that is set. As such, if a thread runs on a cpu with a
larger cpu id, or for_each_possible_cpu() is used, the driver could index
off the end of the array and return garbage or GPF.
The driver maintains its own internal copy of the "num_possible" cpu value
and sizes arrays by it.
Fix by setting the driver's value to the value of the last cpu id bit set
in the possible_mask - plus 1. Thus cpu_map will be sized to allow access
by any cpu id possible.
Link: https://lore.kernel.org/r/20191121175556.18953-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Looking at the recent conversion from smp_processor_id() to
raw_smp_processor_id(), realized that the allocation should be based on the
cpu the hdwq is bound to, not the executing cpu.
Revise to pull cpu number from the hdwq
Fixes: 765ab6cdac ("scsi: lpfc: Fix a kernel warning triggered by lpfc_get_sgl_per_hdwq()")
Link: https://lore.kernel.org/r/20191116003847.6141-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.6.0.2
Link: https://lore.kernel.org/r/20191111230401.12958-7-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is setting the initiator nvme template with a max hw queues value of
the present cpu count which is odd. It should be registering the number of
hdwq queues (queues created on the adapter).
Change to set nvme tempate, in all cases, to the number of hardware queues.
Link: https://lore.kernel.org/r/20191111230401.12958-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, cpu_map[cpu#]->hdwq is left to equal LPFC_VECTOR_MAP_EMPTY for
not present CPUs. If a CPU is dynamically hot-added, it is possible we may
crash due to not assigning an allocated hdwq.
Correct by assigning a hdwq at initialization for all not-present CPUs.
Fixes: dcaa213679 ("scsi: lpfc: Change default IRQ model on AMD architectures")
Link: https://lore.kernel.org/r/20191111230401.12958-5-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Compilation can fail due to having an inline function reference where the
function body is not present.
Fix by removing the inline tag.
Fixes: 93a4d6f401 ("scsi: lpfc: Add registration for CPU Offline/Online events")
Link: https://lore.kernel.org/r/20191111230401.12958-4-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity reported the following:
*** CID 101747: Null pointer dereferences (FORWARD_NULL)
/drivers/scsi/lpfc/lpfc_els.c: 4439 in lpfc_cmpl_els_rsp()
4433 kfree(mp);
4434 }
4435 mempool_free(mbox, phba->mbox_mem_pool);
4436 }
4437 out:
4438 if (ndlp && NLP_CHK_NODE_ACT(ndlp)) {
vvv CID 101747: Null pointer dereferences (FORWARD_NULL)
vvv Dereferencing null pointer "shost".
4439 spin_lock_irq(shost->host_lock);
4440 ndlp->nlp_flag &= ~(NLP_ACC_REGLOGIN | NLP_RM_DFLT_RPI);
4441 spin_unlock_irq(shost->host_lock);
4442
4443 /* If the node is not being used by another discovery thread,
4444 * and we are sending a reject, we are done with it.
Fix by adding a check for non-null shost in line 4438.
The scenario when shost is set to null is when ndlp is null.
As such, the ndlp check present was sufficient. But better safe
than sorry so add the shost check.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 101747 ("Null pointer dereferences")
Fixes: 2e0fef85e0 ("[SCSI] lpfc: NPIV: split ports")
CC: James Bottomley <James.Bottomley@SteelEye.com>
CC: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
CC: linux-next@vger.kernel.org
Link: https://lore.kernel.org/r/20191111230401.12958-3-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following kernel warning:
cpumask_of_node(-1): (unsigned)node >= nr_node_ids(1)
Fixes: dcaa213679 ("scsi: lpfc: Change default IRQ model on AMD architectures")
Link: https://lore.kernel.org/r/20191108225947.1395-1-jsmart2021@gmail.com
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following kernel bug report:
BUG: using smp_processor_id() in preemptible [00000000] code: systemd-udevd/954
Fixes: d79c9e9d4b ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.")
Link: https://lore.kernel.org/r/20191107052158.25788-2-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.6.0.1
Link: https://lore.kernel.org/r/20191105005708.7399-12-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some adapters support the ability to hold multiple adapter dumps on the
adapter flash. Some adapters default to enabling this feature while others
default to single-dump.
Make support uniform by enabling dual dump by default.
Link: https://lore.kernel.org/r/20191105005708.7399-11-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current driver attempts to allocate an interrupt vector per cpu using
the systems managed IRQ allocator (flag PCI_IRQ_AFFINITY). The system IRQ
allocator will either provide the per-cpu vector, or return fewer
vectors. When fewer vectors, they are evenly spread between the numa nodes
on the system. When run on an AMD architecture, if interrupts occur to a
cpu that is not in the same numa node as the adapter generating the
interrupt, there are extreme costs and overheads in performance. Thus, if
1:1 vector allocation is used, or the "balanced" vectors in the other numa
nodes, performance can be hit significantly.
A much more performant model is to allocate interrupts only on the cpus
that are in the numa node where the adapter resides. I/O completion is
still performed by the cpu where the I/O was generated. Unfortunately,
there is no flag to request the managed IRQ subsystem allocate vectors only
for the CPUs in the numa node as the adapter.
On AMD architecture, revert the irq allocation to the normal style
(non-managed) and then use irq_set_affinity_hint() to set the cpu
affinity and disable user-space rebalancing.
Tie the support into CPU offline/online. If the cpu being offlined owns a
vector, the vector is re-affinitized to one of the other CPUs on the same
numa node. If there are no more CPUs on the numa node, the vector has all
affinity removed and lets the system determine where it's serviced.
Similarly, when the cpu that owned a vector comes online, the vector is
reaffinitized to the cpu.
Link: https://lore.kernel.org/r/20191105005708.7399-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The recent affinitization didn't address cpu offlining/onlining. If an
interrupt vector is shared and the low order cpu owning the vector is
offlined, as interrupts are managed, the vector is taken offline. This
causes the other CPUs sharing the vector will hang as they can't get io
completions.
Correct by registering callbacks with the system for Offline/Online
events. When a cpu is taken offline, its eq, which is tied to an interrupt
vector is found. If the cpu is the "owner" of the vector and if the
eq/vector is shared by other CPUs, the eq is placed into a polled mode.
Additionally, code paths that perform io submission on the "sharing CPUs"
will check the eq state and poll for completion after submission of new io
to a wq that uses the eq.
Similarly, when a cpu comes back online and owns an offlined vector, the eq
is taken out of polled mode and rearmed to start driving interrupts for eq.
Link: https://lore.kernel.org/r/20191105005708.7399-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current message on FAWWN events is rather cryptic.
Expand the message to clarify its meaning.
Link: https://lore.kernel.org/r/20191105005708.7399-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prior to the last FC-NVME-2 draft, SLER and CONF were independent. SLER
now requires CONF to be set.
Revise the NVME PRLI checking to look for both inorder to enable SLER.
Link: https://lore.kernel.org/r/20191105005708.7399-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The recently posted patch had a typo that incorrectly tested the receiving
function.
Fix the typo (change == to !=)
Fixes: 95bfc6d8ad ("scsi: lpfc: Make FW logging dynamically configurable")
Link: https://lore.kernel.org/r/20191105005708.7399-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During heavy RCN activity and log_verbose = 0 we see these messages:
2754 PRLI failure DID:521245 Status:x9/xb2c00, data: x0
0231 RSCN timeout Data: x0 x3
0230 Unexpected timeout, hba link state x5
This is due to delayed RSCN activity.
Correct by avoiding the timeout thus the messages by restarting the
discovery timeout whenever an rscn is received.
Filter PRLI responses such that severity depends on whether expected for
the configuration or not. For example, PRLI errors on a fabric will be
informational (they are expected), but Point-to-Point errors are not
necessarily expected so they are raised to an error level.
Link: https://lore.kernel.org/r/20191105005708.7399-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When reading sysfs nvme_info file while a remote port leaves and comes
back, a NULL pointer is encountered. The issue is due to ndlp list
corruption as the the nvme_info_show does not use the same lock as the rest
of the code.
Correct by removing the rcu_xxx_lock calls and replace by the host_lock and
phba->hbaLock spinlocks that are used by the rest of the driver. Given
we're called from sysfs, we are safe to use _irq rather than _irqsave.
Link: https://lore.kernel.org/r/20191105005708.7399-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver today is reading service parameters from the firmware and then
overwriting the firmware-provided values with values of its own. There are
some switch features that require preliminary FLOGI's that are
switch-specific and done prior to the actual fabric FLOGI for traffic. The
fw will perform those FLOGIs and will revise the service parameters for the
features configured. As the driver later overwrites those values with its
own values, it misconfigures things like BBSCN use by doing so.
Correct by eliminating the driver-overwrite of firmware values. The driver
correctly re-reads the service parameters after each link up to obtain the
latest values from firmware.
Link: https://lore.kernel.org/r/20191105005708.7399-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the driver receives a login that is later then LOGO'd by the remote port
(aka ndlp), the driver, upon the completion of the LOGO ACC transmission,
will logout the node and unregister the rpi that is being used for the
node. As part of the unreg, the node's rpi value is replaced by the
LPFC_RPI_ALLOC_ERROR value. If the port is subsequently offlined, the
offline walks the nodes and ensures they are logged out, which possibly
entails unreg'ing their rpi values. This path does not validate the node's
rpi value, thus doesn't detect that it has been unreg'd already. The
replaced rpi value is then used when accessing the rpi bitmask array which
tracks active rpi values. As the LPFC_RPI_ALLOC_ERROR value is not a valid
index for the bitmask, it may fault the system.
Revise the rpi release code to detect when the rpi value is the replaced
RPI_ALLOC_ERROR value and ignore further release steps.
Link: https://lore.kernel.org/r/20191105005708.7399-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nine changes, eight in drivers [ufs, target, lpfc x 2, qla2xxx x 4]
and one core change in sd that fixes an I/O failure on DIF type 3
devices.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXbzO+iYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYOpAP9/BCSY
2TAFlli2rVQe+ZNjhHcE4Gj92HNPO7ZgvDQvWgD9F184tjG+1pntYGFutoso7Ak6
QimtBw4AuYg9eDKJDKU=
=bQRX
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine changes, eight in drivers [ufs, target, lpfc x 2, qla2xxx x 4]
and one core change in sd that fixes an I/O failure on DIF type 3
devices"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: stop timer in shutdown path
scsi: sd: define variable dif as unsigned int instead of bool
scsi: target: cxgbit: Fix cxgbit_fw4_ack()
scsi: qla2xxx: Fix partial flash write of MBI
scsi: qla2xxx: Initialized mailbox to prevent driver load failure
scsi: lpfc: Honor module parameter lpfc_use_adisc
scsi: ufs-bsg: Wake the device before sending raw upiu commands
scsi: lpfc: Check queue pointer before use
scsi: qla2xxx: fixup incorrect usage of host_byte
Fix sparse warning:
drivers/scsi/lpfc/lpfc_debugfs.c:2083:1: warning:
symbol 'lpfc_debugfs_ras_log_data' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20191028132556.16272-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
mempool_destroy has taken null pointer check into account. Remove the
redundant check.
Link: https://lore.kernel.org/r/20191026194712.GA22249@saurav
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
convert MAGIC_NUMER_xxx to MAGIC_NUMBER_xxx
Link: https://lore.kernel.org/r/20191025184342.6623-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_debufs.c was missing include of vmalloc.h when compiled on PPC.
Add missing header.
Link: https://lore.kernel.org/r/20191025182530.26653-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nine changes, eight to drivers (qla2xxx, hpsa, lpfc, alua, ch,
53c710[x2], target) and one core change that tries to close a race
between sysfs delete and module removal.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXbN1gSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWUzAP4tB9Z+
X5zfnMLmeAtSCnVwIgFX3/GVSFfzEmi+3VxfBQEA3nfs5AAJCPsaTk9z+jLtAKPk
6uYoHwsyTHal19Ojt9g=
=IOPn
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine changes, eight to drivers (qla2xxx, hpsa, lpfc, alua, ch,
53c710[x2], target) and one core change that tries to close a race
between sysfs delete and module removal"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: remove left-over BUILD_NVME defines
scsi: core: try to get module before removing device
scsi: hpsa: add missing hunks in reset-patch
scsi: target: core: Do not overwrite CDB byte 1
scsi: ch: Make it possible to open a ch device multiple times again
scsi: fix kconfig dependency warning related to 53C700_LE_ON_BE
scsi: sni_53c710: fix compilation error
scsi: scsi_dh_alua: handle RTPG sense code correctly during state transitions
scsi: qla2xxx: fix a potential NULL pointer dereference
Replace assignment of 0 to pointer with NULL assignment.
Link: https://lore.kernel.org/r/20191024030857.GA12097@saurav
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace assignment of 0 to pointer with NULL assignment.
Link: https://lore.kernel.org/r/20191024025726.GA31421@saurav
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.6.0.0
Link: https://lore.kernel.org/r/20191018211832.7917-17-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When debugging a recent discovery customer problem it was very hard to tell
what was happening with the existing discovery log messages. To fully debug
the issue additional log messages were necessary.
Add or extend log messages so that sufficient information is present for
debugging.
Link: https://lore.kernel.org/r/20191018211832.7917-16-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the past, the lpe32000 models, based their main support being for 32G,
and as FC-AL is not supported in the FC standards past 8G, did not support
FC-AL operation.
This patch adds private-loop FC-AL support for the LPE32000 adapters
when a link is 8G or below. To avoid conditions where link rate may
change, which would cause non-connectivity to the AL device, FC-AL
mode must become a persistent setting and the link kept at a speed
supporting FC-AL.
The patch:
- Adds a pls attribute indicating whether the adapter properly supports
FC-AL.
- Adds support for the adapter to indicate that topology should be fixed
and the topology types to be configured.
- Adds a pt attribute to report the persistent topology if present.
Link: https://lore.kernel.org/r/20191018211832.7917-15-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add decode support for adapter Async Events which report FA-WWN
configuration errors.
Link: https://lore.kernel.org/r/20191018211832.7917-14-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add two new macros to aid in message logging:
Both macros print a message if the corresponding lpfc verbosity setting is
set or the kernel log level is WARNING or more critical.
One macro is for use with a phba structure, the other with a vport
structure.
[mkp: typo]
Link: https://lore.kernel.org/r/20191018211832.7917-13-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the FW logging facility is a load/boot time parameter which
requires the driver to be unloaded/reloaded or the system rebooted in order
to change its configuration.
Convert the logging facility to allow dynamic enablement and configuration.
Specifically:
- Convert the feature so that it can be enabled dynamically via an
attribute. Additionally, the size of the buffer can be configured
dynamically.
- Add locks around states that now may be changing.
- Tie the feature into debugfs so that the logs can be read at any time.
Link: https://lore.kernel.org/r/20191018211832.7917-12-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The existing "auto eq delay" mechanism was sometimes skipping over an EQ,
not ramping the coalescing down under light load fast enough, and in other
cases never kicked in as cpu sharing by multiple vectors didn't quite add
up right.
Tweak the interrupt mechanism such that:
- Add a flag to the EQ to force checking for colaescing values when being
serviced in the interrupt handler. The flag will be set by any CQ bound
to the EQ whenever the number of CQ elements process in a single scan
meets or exceeds the hardware queue notify level. E.g. there's a
significant number of completions happening.
- In the heartbeat work item that checks coalescing:
- Replace the structure that was counting the number of EQs that
interrupted on a single cpu with a new structure that looks at the EQ
to see whether EQ currently has a coalescing value (thus it should be
re-evaluate) or was marked by the new flag indicating heavy
completions.
- When a cpu, which may be servicing multiple vectors, had at least 1 EQ
that should be checked, a new coalescing delay is calculated based on
the number of interrupts that occurred on the cpu.
- The new coalescing value is then applied to the EQs that had
interrupted on the cpu.
Link: https://lore.kernel.org/r/20191018211832.7917-11-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Lower IOps performance with write operations. Perf tool shows lock
contention in dma_pool_alloc and dma_pool_free related to the
txrdy_payload_pool.
The allocations are for dma buffers for XFER_RDY's, which actually are not
needed for the FCP_TRECEIVE command as the command contents are used by the
adapter to generate the IU.
Remove the allocations and the associated buffer pool. Rather than leaving
NULLs in buffer pointer locations, set command and sgl to indicate skipped
SGLE indexes.
Link: https://lore.kernel.org/r/20191018211832.7917-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Slightly rework some error check code paths for better streamlining.
Added compiler unlikely hints to allow slightly better optimization of the
fast-path.
Removed a few pointer checks that were obviously already valid.
Link: https://lore.kernel.org/r/20191018211832.7917-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Log message conditional upon vport being NULL dereferences vport to
determine log verbose setting.
Changed to use lpfc_print_log which uses phba to determine the active log
verbose setting.
Fixes: 43bfea1bff ("scsi: lpfc: Fix coverity errors on NULL pointer checks")
Link: https://lore.kernel.org/r/20191018211832.7917-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In lpfc_abort_handler, the lock acquire order is hbalock (irqsave),
buf_lock (irq) and ring_lock (irq). The issue is that in two places the
locks are released out of order - the buf_lock and the hbalock - resulting
in the cpu preemption/lock flags getting restored out of order and
deadlocking the cpu.
Fix the unlock order by fully releasing the hbalocks as well.
CC: Zhangguanghui <zhang.guanghui@h3c.com>
Link: https://lore.kernel.org/r/20191018211832.7917-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In cases where I/O may be aborted, such as driver unload or link bounces,
the system will crash based on a bad ndlp pointer.
Example:
RIP: 0010:lpfc_sli4_abts_err_handler+0x15/0x140 [lpfc]
...
lpfc_sli4_io_xri_aborted+0x20d/0x270 [lpfc]
lpfc_sli4_sp_handle_abort_xri_wcqe.isra.54+0x84/0x170 [lpfc]
lpfc_sli4_fp_handle_cqe+0xc2/0x480 [lpfc]
__lpfc_sli4_process_cq+0xc6/0x230 [lpfc]
__lpfc_sli4_hba_process_cq+0x29/0xc0 [lpfc]
process_one_work+0x14c/0x390
Crash was caused by a bad ndlp address passed to I/O indicated by the XRI
aborted CQE. The address was not NULL so the routine deferenced the ndlp
ptr. The bad ndlp also caused the lpfc_sli4_io_xri_aborted to call an
erroneous io handler. Root cause for the bad ndlp was an lpfc_ncmd that
was aborted, put on the abort_io list, completed, taken off the abort_io
list, sent to lpfc_release_nvme_buf where it was put back on the abort_io
list because the lpfc_ncmd->flags setting LPFC_SBUF_XBUSY was not cleared
on the final completion.
Rework the exchange busy handling to ensure the flags are properly set for
both scsi and nvme.
Fixes: c490850a09 ("scsi: lpfc: Adapt partitioned XRI lists to efficient sharing")
Cc: <stable@vger.kernel.org> # v5.1+
Link: https://lore.kernel.org/r/20191018211832.7917-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When operating in private loop mode, PLOGI exchanges are racing and the
driver tries to abort it's PLOGI. But the PLOGI abort ends up terminating
the login with the other end causing the other end to abort its PLOGI as
well. Discovery never fully completes.
Fix by disabling the PLOGI abort when private loop and letting the state
machine play out.
Link: https://lore.kernel.org/r/20191018211832.7917-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix lockdep error in __lpfc_sli_ringtx_put(): The hbalock is valid for
sli3, but not for sli4. Change lockdep to look at ring lock if sli4.
Also update comment in __lpfc_sli_issue_iocb_s4() to reflect proper
lock. Note: lockdep check is already correct.
Link: https://lore.kernel.org/r/20191018211832.7917-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the adapter FW is administratively set to RO mode, a FW update
triggered by the driver's sysfs attribute will fail. Currently, the
driver's logging mechanism does not properly parse the adapter return codes
and print a meaningful message. This oversight prevents quick diagnosis in
the field.
Parse the adapter return codes for Write_Object and write an appropriate
message to the system console.
[mkp: typo]
Link: https://lore.kernel.org/r/20191018211832.7917-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, lpfc_nvmet_mrq is always scaled back to the min(lpfc_nvmet_mrq,
lpfc_irq_chann). There's no reason to reduce it to the number of interrupt
vectors. Rather, it should be scaled down based on the number of hardware
queues for the system (if lower than max of 16).
Change scaling to use hardware queue count rather than interrupt vector
count.
Link: https://lore.kernel.org/r/20191018211832.7917-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The initial lpfc_desc_set_adisc implementation in commit
dea3101e0a ("lpfc: add Emulex FC driver version 8.0.28") enabled ADISC if
cfg_use_adisc && RSCN_MODE && FCP_2_DEVICE
In commit 92d7f7b0cd ("[SCSI] lpfc: NPIV: add NPIV support on top of
SLI-3") this changed to
(cfg_use_adisc && RSC_MODE) || FCP_2_DEVICE
and later in commit ffc954936b ("[SCSI] lpfc 8.3.13: FC Discovery Fixes
and enhancements.") to
(cfg_use_adisc && RSC_MODE) || (FCP_2_DEVICE && FCP_TARGET)
A customer reports that after a devloss, an ADISC failure is logged. It
turns out the ADISC flag is set even the user explicitly set lpfc_use_adisc
= 0.
[Sat Dec 22 22:55:58 2018] lpfc 0000:82:00.0: 2:(0):0203 Devloss timeout on WWPN 50:01:43:80:12:8e:40:20 NPort x05df00 Data: x82000000 x8 xa
[Sat Dec 22 23:08:20 2018] lpfc 0000:82:00.0: 2:(0):2755 ADISC failure DID:05DF00 Status:x9/x70000
[mkp: fixed Hannes' email]
Fixes: 92d7f7b0cd ("[SCSI] lpfc: NPIV: add NPIV support on top of SLI-3")
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: James Smart <james.smart@broadcom.com>
Link: https://lore.kernel.org/r/20191022072112.132268-1-dwagner@suse.de
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The queue pointer might not be valid. The rest of the code checks the
pointer before accessing it. lpfc_sli4_process_missed_mbox_completions is
the only place where the check is missing.
Fixes: 657add4e5e ("scsi: lpfc: Fix poor use of hardware queues if fewer irq vectors")
Cc: James Smart <jsmart2021@gmail.com>
Link: https://lore.kernel.org/r/20191018162111.8798-1-dwagner@suse.de
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The BUILD_NVME define never got defined anywhere, causing NVMe commands to
be treated as SCSI commands when freeing the buffers. This was causing a
stuck discovery and a horrible crash in lpfc_set_rrq_active() later on.
Link: https://lore.kernel.org/r/20191017150019.75769-1-hare@suse.de
Fixes: c00f62e6c5 ("scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/lpfc/lpfc_nportdisc.c:290:1: warning: symbol 'lpfc_defer_pt2pt_acc' was not declared. Should it be static?
Link: https://lore.kernel.org/r/1570183477-137273-1-git-send-email-zhengbin13@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Local variable fcp_txcmplq_cnt is initialized to 0 and then displayed in
lpfc driver message 0387.
Presumed residual (or unused) code from previous commit.
Removed fcp_txcmplq_cnt.
Link: https://lore.kernel.org/r/20190922035906.10977-20-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
T10 PI support on SLI-4-based FCoE adapters is not supported. A prior
commit in the 12.4.0.0 stream added device recognition that would prevent
T10 PI enablement. However, it didn't contain a complete device list. Thus
some SLI-4 FCoE adapters still had T10 PI enabled.
Fix by expanding the device list that identifies FCoE devices.
Link: https://lore.kernel.org/r/20190922035906.10977-19-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch updates ACQE handling for:
- an EEPROM failure error reported by the adapter.
- ensures that all data for any ACQE, recognized or not, is logged.
- Given that all data is now logged unconditionally, the default case
(unrecognized) data can be reduced.
Link: https://lore.kernel.org/r/20190922035906.10977-18-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In lpfc_release_io_buf, an lpfc_io_buf is returned to the 'available' pool
before any associated sgl or cmd and rsp buffers are returned via their
respective 'put' routines. If xri rebalancing occurs and an lpfc_io_buf
structure is reused quickly, there may be a race condition between release
of old and association of new resources.
Re-ordered lpfc_release_io_buf to release sgl and cmd/rsp
buffer lists before releasing the lpfc_io_buf structure for re-use.
Fixes: d79c9e9d4b ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.")
Link: https://lore.kernel.org/r/20190922035906.10977-17-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many of the sgl-per-hdwq paths are locking with spin_lock_irq() and
spin_unlock_irq() and may unwittingly raising irq when it shouldn't. Hard
deadlocks were seen around lpfc_scsi_prep_cmnd().
Fix by converting the locks to irqsave/irqrestore.
Fixes: d79c9e9d4b ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.")
Link: https://lore.kernel.org/r/20190922035906.10977-16-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While reviewing the CT behavior, issues with spinlock_irq were seen. The
driver should be using spinlock_irqsave/irqrestore in the els flush
routine.
Changed to spinlock_irqsave/irqrestore.
Link: https://lore.kernel.org/r/20190922035906.10977-15-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After study, it was determined there was a double free of a CT iocb during
execution of lpfc_offline_prep and lpfc_offline. The prep routine issued
an abort for some CT iocbs, but the aborts did not complete fast enough for
a subsequent routine that waits for completion. Thus the driver proceeded
to lpfc_offline, which releases any pending iocbs. Unfortunately, the
completions for the aborts were then received which re-released the ct
iocbs.
Turns out the issue for why the aborts didn't complete fast enough was not
their time on the wire/in the adapter. It was the lpfc_work_done routine,
which requires the adapter state to be UP before it calls
lpfc_sli_handle_slow_ring_event() to process the completions. The issue is
the prep routine takes the link down as part of it's processing.
To fix, the following was performed:
- Prevent the offline routine from releasing iocbs that have had aborts
issued on them. Defer to the abort completions. Also means the driver
fully waits for the completions. Given this change, the recognition of
"driver-generated" status which then releases the iocb is no longer
valid. As such, the change made in the commit 296012285c is reverted.
As recognition of "driver-generated" status is no longer valid, this
patch reverts the changes made in
commit 296012285c ("scsi: lpfc: Fix leak of ELS completions on adapter reset")
- Modify lpfc_work_done to allow slow path completions so that the abort
completions aren't ignored.
- Updated the fdmi path to recognize a CT request that fails due to the
port being unusable. This stops FDMI retries. FDMI will be restarted on
next link up.
Link: https://lore.kernel.org/r/20190922035906.10977-14-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scenarios were seen where a host hung when the system booted or the host
was very slow in booting. The link would not come up and no luns were
visible to the host.
After investigation, this was found to be due to the introduction of a new
ACQE that adapter may generate to report a adapter hw warning. The ACQE was
delivered to the driver very early in adapter initialization, when the
driver did not expect command completion. As part of handling this
unexpected interrupt the an EQEs are consumed and discarded and the EQ
rearmed. The issue is the CQ that cause the EQE and thus the interrupt was
not processed and the CQ was left unarmed. Meaning it would no longer
generate a new interrupt condition. Subsequent mailbox commands used to
initialize the adapter use the same CQ, and as there was no completion
interrupt generated, the driver never saw the mailbox commands complete and
it would wait long command timeouts.
Fix by having the early flush routine also process the related CQ and rearm
the CQ.
Link: https://lore.kernel.org/r/20190922035906.10977-13-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity flagged several scenarios where checking of null pointer values
wasn't consistent.
Fix the code to that be consistent on checking.
Link: https://lore.kernel.org/r/20190922035906.10977-12-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the port, running as a nvme target, receives an ABTS, it submits
commands to the adapter to Abort i/o outstanding in the adapter. The Abort
command formatting routine left a command field set to zero, which
instructs the adapter to generate an ABTS on the wire as part of cleaning
up the I/O. This is common operation for an initiator, but not for a
target.
Fix the driver to check whether an ABTS had been received for the I/O, and
if so, change the Abort command formatting so that the ABTS generation is
disabled (IA=1). No need to ABTS it when the other side already has.
Also refactored the code such that there is a single routine being used for
nvme or nvmet ABORT requests, and IA is an argument.
Link: https://lore.kernel.org/r/20190922035906.10977-11-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An issue was seen discovering all SCSI Luns when a target device undergoes
link bounce.
The driver currently does not qualify the FC4 support on the target.
Therefore it will send a SCSI PRLI and an NVMe PRLI. The expectation is
that the target will reject the PRLI if it is not supported. If a PRLI
times out, the driver will retry. The driver will not proceed with the
device until both SCSI and NVMe PRLIs are resolved. In the failure case,
the device is FCP only and does not respond to the NVMe PRLI, thus
initiating the wait/retry loop in the driver. During that time, a RSCN is
received (device bounced) causing the driver to issue a GID_FT. The GID_FT
response comes back before the PRLI mess is resolved and it prematurely
cancels the PRLI retry logic and leaves the device in a STE_PRLI_ISSUE
state. Discovery with the target never completes or resets.
Fix by resetting the node state back to STE_NPR_NODE when GID_FT completes,
thereby restarting the discovery process for the node.
Link: https://lore.kernel.org/r/20190922035906.10977-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Faults are seen with RIP of lpfc_scsi_cmd_iocb_cmpl(). The failure is when
lpfc_update_status is being called as part of the completion. After
debugging, it was seen the issue was the shost pointer that the driver
derived from the scsi cmd. The crash showed the cmd->device pointer being
bogus, which is likely as the scsi devices were offlined prior. The bogus
device pointer caused subsequent pointers derived from the location,
specifically the vport, to be bogus.
Fix by adjusting the calling sequence to pass in the vport rather than
having to derive it from the cmd structure.
Link: https://lore.kernel.org/r/20190922035906.10977-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Symptoms were seen of the driver not having valid data for mailbox
commands. After debugging, the following sequence was found:
The driver maintains a port-wide pointer of the mailbox command that is
currently in execution. Once finished, the port-wide pointer is cleared
(done in lpfc_sli4_mq_release()). The next mailbox command issued will set
the next pointer and so on.
The mailbox response data is only copied if there is a valid port-wide
pointer.
In the failing case, it was seen that a new mailbox command was being
attempted in parallel with the completion. The parallel path was seeing
the mailbox no long in use (flag check under lock) and thus set the port
pointer. The completion path had cleared the active flag under lock, but
had not touched the port pointer. The port pointer is cleared after the
lock is released. In this case, the completion path cleared the just-set
value by the parallel path.
Fix by making the calls that clear mbox state/port pointer while under
lock. Also slightly cleaned up the error path.
Link: https://lore.kernel.org/r/20190922035906.10977-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When target-side fault injections are made, the driver isn't reconnecting
to the remote port. The driver is logging "2753" error messages which
state:
"PLOGI failure DID:1B2400 Status:x3/xf0240008"
The failures status is indicating a Illegal field error, which points to
the Temporary RPI field being used for the ELS. This error typically means
the driver used an RPI that was already registered (shouldn't be registered
if using it in this context).
Study has found that if the driver were in discovery attempts and
encountered an error, it wouldn't flag the temporary rpi in error. Yet the
rpi was released for reallocation in these error paths and another ELS
could allocate the rpi. In the failure situation a retry was done on an ELS
that had encountered an error, and as the rpi wasn't marked in error, the
ELS reused the rpi it originally allocated. But that rpi had been allocated
by a different ELS issued after the original error and before the retry
attempt. The different ELS had succeeded and the RPI was registered.
Fix by marking the rpi state for the node to be in error, aka as needing
reallocation, upon an error in the els processing. Error state marking is
always done prior to release back to the internal rpi free list, which the
driver wasn't doing in cases prior.
Also enhanced some of the logging to help in the next case of problem
troubleshooting.
Link: https://lore.kernel.org/r/20190922035906.10977-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A prior use-after-free mailbox fix solved it's problem by null'ing a ndlp
pointer. However, further testing has shown that this change causes a
later state change to occasionally be skipped, which results in a reference
count never being decremented thus the rpi is never released, which causes
a vport delete to never succeed.
Revise the fix in the prior patch to no longer null the ndlp. Instead the
RELEASE_RPI flag is set which will drive the release of the rpi.
Given the new code was added at a deep indentation level, refactor the code
block using a new routine that avoids the indentation issues.
Fixes: 9b16406864 ("scsi: lpfc: Fix use-after-free mailbox cmd completion")
Link: https://lore.kernel.org/r/20190922035906.10977-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The nvme-fc transport may call to abort an io on controller reset. If the
driver is out of resources to issue an abort command, it just gives up and
does nothing. The transport expects the lldd to always be able to terminate
an io it has issued. At that point, the controller hangs waiting for
aborted ios to be returned. Note: flaged by "6136" and "6176" error
messages.
Root issue was the adapter mis-allocated the number resources it allocated
for command entries for the adapter.
Convert the driver to allocate command resources based on the number of
xris supported by the FC port - 1 resource for the original command and 1
resource for the abort request.
Link: https://lore.kernel.org/r/20190922035906.10977-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity flagged missing status check on register read that flags a
poisoned data return value.
Add checking of register read status.
Link: https://lore.kernel.org/r/20190922035906.10977-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use of spin_lock_irq may re-enable interrupts prematurely.
Convert to spin_lock. Note: code is under the phba->hba_lock which has been
locked with irqsave.
Link: https://lore.kernel.org/r/20190922035906.10977-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After exchanging PLOGI on an SLI-3 adapter, the PRLI exchange failed. Link
trace showed the port was assigned a non-zero n_port_id, but didn't use the
address on the PRLI. The assigned address is set on the port by the
CONFIG_LINK mailbox command. The driver responded to the PRLI before the
mailbox command completed. Thus the PRLI response used the old n_port_id.
Defer the PRLI response until CONFIG_LINK completes.
Link: https://lore.kernel.org/r/20190922035906.10977-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates.
The only core change this time around is the addition of request
batching for virtio. Since batching requires an additional flag to
use, it should be invisible to the rest of the drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXYQE/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXs9AP4usPY5
OpMlF6OiKFNeJrCdhCScVghf9uHbc7UA6cP+EgD/bCtRgcDe1ZjOTYWdeTwvwWqA
ltWYonnv6Lg3b1f9yqI=
=jRC/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates. The
only core change this time around is the addition of request batching
for virtio. Since batching requires an additional flag to use, it
should be invisible to the rest of the drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (264 commits)
scsi: hisi_sas: Fix the conflict between device gone and host reset
scsi: hisi_sas: Add BIST support for phy loopback
scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation
scsi: hisi_sas: Remove some unused function arguments
scsi: hisi_sas: Remove redundant work declaration
scsi: hisi_sas: Remove hisi_sas_hw.slot_complete
scsi: hisi_sas: Assign NCQ tag for all NCQ commands
scsi: hisi_sas: Update all the registers after suspend and resume
scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device
scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails
scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled
scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()
scsi: hisi_sas: add debugfs auto-trigger for internal abort time out
scsi: virtio_scsi: unplug LUNs when events missed
scsi: scsi_dh_rdac: zero cdb in send_mode_select()
scsi: fcoe: fix null-ptr-deref Read in fc_release_transport
scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code
scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code
scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code
scsi: ufs: Use kmemdup in ufshcd_read_string_desc()
...
A recent patch unconditionally marks the hba as in error as part of
resetting the adapter. The driver flow that called the adapter reset was a
recovery path, which expects the adapter to not be in an error state in
order to finish the recovery. Given the new error state being set, the
recovery fails and the adapter is left in limbo.
Revise the adapter reset routine so that it will only mark the adapter in
error if it was unable to reset the adapter.
Fixes: 8c24a4f643 ("scsi: lpfc: Fix crash due to port reset racing vs adapter error handling")
Link: https://lore.kernel.org/r/20190903215441.10490-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert the remaining %pf users to %ps to prepare for the removal of the
old %pf conversion specifier support.
Fixes: 3235066449 ("scsi: lpfc: Migrate to %px and %pf in kernel print calls")
Link: https://lore.kernel.org/r/20190904160423.3865-1-sakari.ailus@linux.intel.com
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 12.4.0.0 patch that merged WQ/CQ pairs into single per-cpu pair
contained a bug: a local variable was set to the queue pair by index. This
should have allowed the local variable to be natively used. Instead, the
code reused the index relative to the local variable, obtaining a random
pointer value that when used eventually faulted the system
Convert offending code to use local variable.
Fixes: c00f62e6c5 ("scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Raise the config max for lpfc_fcp_mq_threshold variable to 256.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Capturing and downloading dif command data and dif data was done a dozen
years ago and no longer being used. Also creates a potential security hole.
Remove the debugfs buffer for dif debugging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: KyleMahlkuch <kmahlkuc@linux.vnet.ibm.com>
CC: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Per Dan Carpenter:
The patch d79c9e9d4b: "scsi: lpfc: Support dynamic unbounded SGL lists on
G7 hardware." from Aug 14, 2019, leads to the following static checker
warning:
drivers/scsi/lpfc/lpfc_init.c:4107 lpfc_new_io_buf()
error: not allocating enough data 784 vs 768
There was no need to compare sizes nor to allocate size based on a define.
Change allocation to use actual structure length
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.4.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, each hardware queue, typically allocated per-cpu, consists of a
WQ/CQ pair per protocol. Meaning if both SCSI and NVMe are supported 2
WQ/CQ pairs will exist for the hardware queue. Separate queues are
unnecessary. The current implementation wastes memory backing the 2nd set
of queues, and the use of double the SLI-4 WQ/CQ's means less hardware
queues can be supported which means there may not always be enough to have
a pair per cpu. If there is only 1 pair per cpu, more cpu's may get their
own WQ/CQ.
Rework the implementation to use a single WQ/CQ pair by both protocols.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FC-NVMe-2 added support for sequence level error recovery in the FC-NVME
protocol. This allows for the detection of errors and lost frames and
immediate retransmission of data to avoid exchange termination, which
escalates into NVMeoFC connection and association failures. A significant
RAS improvement.
The driver is modified to indicate support for SLER in the NVMe PRLI is
issues and to check for support in the PRLI response. When both sides
support it, the driver will set a bit in the WQE to enable the recovery
behavior on the exchange. The adapter will take care of all detection and
retransmission.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Typical SLI-4 hardware supports up to 2 4KB pages to be registered per XRI
to contain the exchanges Scatter/Gather List. This caps the number of SGL
elements that can be in the SGL. There are not extensions to extend the
list out of the 2 pages.
The G7 hardware adds a SGE type that allows the SGL to be vectored to a
different scatter/gather list segment. And that segment can contain a SGE
to go to another segment and so on. The initial segment must still be
pre-registered for the XRI, but it can be a much smaller amount (256Bytes)
as it can now be dynamically grown. This much smaller allocation can
handle the SG list for most normal I/O, and the dynamic aspect allows it to
support many MB's if needed.
The implementation creates a pool which contains "segments" and which is
initially sized to hold the initial small segment per xri. If an I/O
requires additional segments, they are allocated from the pool. If the
pool has no more segments, the pool is grown based on what is now
needed. After the I/O completes, the additional segments are returned to
the pool for use by other I/Os. Once allocated, the additional segments are
not released under the assumption of "if needed once, it will be needed
again". Pools are kept on a per-hardware queue basis, which is typically
1:1 per cpu, but may be shared by multiple cpus.
The switch to the smaller initial allocation significantly reduces the
memory footprint of the driver (which only grows if large ios are
issued). Based on the several K of XRIs for the adapter, the 8KB->256B
reduction can conserve 32MBs or more.
It has been observed with per-cpu resource pools that allocating a resource
on CPU A, may be put back on CPU B. While the get routines are distributed
evenly, only a limited subset of CPUs may be handling the put routines.
This can put a strain on the lpfc_put_cmd_rsp_buf_per_cpu routine because
all the resources are being put on a limited subset of CPUs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added code to support driver loopback with MDS Diagnostics. This style of
diagnostics passes frames from the fabric to the driver who then echo them
back out the link. SEND_FRAME WQEs are used to transmit the frames. Added
the SOF and EOF field location definitions for use by SEND_FRAME.
Also ensure that enable_mds_diags is a RW parameter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To aid better hardware detection when there are issues, report the first
and second level hardware revisions from the READ_REV command. Add the
elements to the existing hardware id string.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to see real addresses, convert %p with %px for kernel addresses
and replace %p with %pf for functions.
While converting, standardize on "x%px" throughout (not %px or 0x%px).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While performing code review, several relatively simple optimizations can
be done in the fast path.
Add these optimizations (unlikely designators).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Running on Coverity produced the following errors:
- coding style (indentation)
- memset size mismatch errors
note: comment cases where it is purposely a mismatch
Fix the errors.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
modinfo for lpfc_nvme_enable_fb is incorrect. FirstBurst on lpfc target is
not fully supported.
Update the attribute description
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is allowing the user to change lpfc_enable_bg while loading the
driver against a FCoE adapter. This is not supported.
No check is made for the adapter type when applying the blockguard
enablement value.
Fix by verifying the adapter type before setting the enablement flag.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
GetTrunkInfo is displaying an incorrect link speed when the link is a trunk
and the link has gone down. The driver is not clearing the logical speed
as part of the link down transition.
Fix by setting the logical speed to UNKNOWN SPEED when the link goes down.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Max Frame Size value is shown as 34816 in fdmishow from Switch.
The driver uses bbRcvSize in common service param which is obtained from
the READ_SPARM mailbox command. The bbRcvSize field which is displayed is a
three nibble field but the driver is printing a full four nibbles.
Fix by masking off the upper nibble.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The scsi transport fc bsg interface does not expect the bsg_job_done()
callback to be done if the bsg request call returns failure. Several of the
HST_VENDOR cases in the driver unconditionally call bsg_job_done()
regardless of the returning value.
Fix the code to only call bsg_job_done() if the call to lpfc_bsg_request()
will return success.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When forcing the use of MSI (vs MSI-X) the driver is crashing in
pci_irq_get_affinity.
The driver was not using the new pci_alloc_irq_vectors interface in the MSI
path.
Fix by using pci_alloc_irq_vectors() with PCI_RQ_MSI in the MSI path.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently reporting a non-zero nvme sg_seg_cnt value of 256
when nvme is disabled. It should be zero.
Fix by ensuring the value is cleared.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an unsolicited ABTS was received, the driver looks up the exchange it
references. It it does various searches looking for the exchange
context. When one is eventually matched and it is associated with an XRI
context, the driver sends an ABORT WQE to terminate the exchange. Current
code looks at whether the transport had taken action on the XRI yet or not
(no action if set to LPFC_NVMET_STE_RCV; action if non-LPFC_NVMET_STE_RCV).
Based on action or not one of two (sol vs unsol) issue abort routines are
called. The unsol version cheats and transmits a sequence containing an
ABTS with no interaction with the adapter. The sol version issues an Abort
WQE and lets the adapter manage whether the ABTS is sent to not.
The issue is the unsol version is sending ABTS unconditionally for the
exchange that received the ABTS. It's unnecessary.
Remove the conditional and just call the adapter command-based routine to
let the adapter manage the ABTS.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As part of firmware download, the adapter is reset. On the adapter the
reset causes the function to stop and all outstanding io is terminated
(without responses). The reset path then starts teardown of the adapter,
starting with deregistration of the remote ports with the nvme-fc
transport. The local port is then deregistered and the driver waits for
local port deregistration. This never finishes.
The remote port deregistrations terminated the nvme controllers, causing
them to send aborts for all the outstanding io. The aborts were serviced in
the driver, but stalled due to its state. The nvme layer then stops to
reclaim it's outstanding io before continuing. The io must be returned
before the reset on the controller is deemed complete and the controller
delete performed. The remote port deregistration won't complete until all
the controllers are terminated. And the local port deregistration won't
complete until all controllers and remote ports are terminated. Thus things
hang.
The issue is the reset which stopped the adapter also stopped all the
responses that would drive i/o completions, and the aborts were also
stopped that stopped i/o completions. The driver, when resetting the
adapter like this, needs to be generating the completions as part of the
adapter reset so that I/O complete (in error), and any aborts are not
queued.
Fix by adding flush routines whenever the adapter port has been reset or
discovered in error. The flush routines will generate the completions for
the scsi and nvme outstanding io. The abort ios, if waiting, will be caught
and flushed as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This issue is specific to SLI-3 adapters, specifically when DIF is used.
Once seen, this message floods the logs:
9064 BLKGRD: lpfc_scsi_prep_dma_buf_s3: Too many sg segments from
dma_map_sg
The driver, upon detecting an error such as too many elements in an sglist,
misrepresents the error by treating it as a temporary resource issue by
returning MLQUEUE_HOST_BUSY. In these cases, no retry will fix it and it
should have been a hard error. The repeated retry was causing the spamming
of the log.
As for the initial reason of why an I/O encountered this issue at all is
not clear as parameters set by the driver should have avoided this. The
dm multipath maintainer has been notified of the issue.
Fix by changing the return code for the dma mapping routines to indicate
cases that are not retryable and return DID_ERROR on those cases.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter encounters a condition which causes the adapter to fail
(driver must detect the failure) simultaneously to a request to the driver
to reset the adapter (such as a host_reset), the reset path will be racing
with the asynchronously-detect adapter failure path. In the failing
situation, one path has started to tear down the adapter data structures
(io_wq's) while the other path has initiated a repeat of the teardown and
is in the lpfc_sli_flush_xxx_rings path and attempting to access the
just-freed data structures.
Fix by the following:
- In cases where an adapter failure is detected, rather than explicitly
calling offline_eratt() to start the teardown, change the adapter state
and let the later calls of posted work to the slowpath thread invoke the
adapter recovery. In essence, this means all requests to reset are
serialized on the slowpath thread.
- Clean up the routine that restarts the adapter. If there is a failure
from brdreset, don't immediately error and leave things in a partial
state. Instead, ensure the adapter state is set and finish the teardown
of structures before returning.
- If in the scsi host reset handler and the board fails to reset and
restart (which can be due to parallel reset/recovery paths), instead of
hard failing and explicitly calling offline_eratt() (which gets into the
redundant path), just fail out and let the asynchronous path resolve the
adapter state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During cable pull testing a deadlock was seen between lpfc_nlp_counters()
vs lpfc_mbox_process_link_up() vs lpfc_work_list_done(). They are all
waiting on the shost->host_lock.
Issue is all of these cases raise irq when taking out the lock but use
spin_unlock_irq() when unlocking. The unlock path is will unconditionally
re-enable interrupts in cases where irq state should be preserved. The
re-enablement allowed the other paths to execute which then causes the
deadlock.
Fix by converting the lock/unlock to irqsave/irqrestore.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a test with high nvme remote port counts connected via a multi-hop FC
switch config where switches were systematically reset (e.g. fabric
partitioning and re-establishment), the nvme remote ports would switch
addresses based on the switch reconfiguration events. The driver would get
into a situation where the nvme port changed address, PLOGI and PRLI would
succeed nvme transport registration occurred, but subsequent LS requests by
the nvme subsystem failed due to a bad ndlp state and connectivity to the
device failed.
The driver hit a race condition on multiple devices that address swapped
simultaneously. In cases where the driver notices the remote port structure
came back as the same value as previously (meaning a nvme_rport structure
was re-enabled and did not go through devloss_tmo/connect_tmo_failures on
all controllers) the driver would unconditionally exit assuming the ndlp
information was correct. But, if the ndlp's had been swapped, the ndlp had
stale port state information, which when used by the LS request commands,
would fail the commands.
Fix by checking whether a node swap had occurred, and only exit if no ndlp
swap had occurred.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In situations where zoning is not being used, thus NVMe initiators see
other NVMe initiators as well as NVMe targets, a link bounce on an
initiator will cause the NVMe initiators to spew "6169" State Error
messages.
The driver is not qualifying whether the remote port is a NVMe targer or
not before calling the lpfc_nvme_rescan_port(), which validates the role
and prints the message if its only an NVMe initiator.
Fix by the following:
- Before calling lpfc_nvme_rescan_port() ensure that the node is a NVMe
storage target or a NVMe discovery controller.
- Clean up implementation of lpfc_nvme_rescan_port. remoteport pointer
will always be NULL if a NVMe initiator only. But, grabbing of
remoteport pointer should be done under lock to coincide with the
registering of the remote port with the fc transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On an SLI-3 adapter which does not support NVMe, but with the driver global
attribute to enable nvme on any adapter if it does support NVMe
(e.g. module parameter lpfc_enable_fc4_type=3), the SGL and total SGE
values are being munged by the protocol enablement when it shouldn't be.
Correct by changing the location of where the NVME sgl information is being
applied, which will avoid any SLI-3-based adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If admin changes the devloss_tmo on an rport via the fc_remote_port rport
dev_loss_tmo attribute, the value is on set on scsi stack. The change is
not propagated to NVMe.
The set routine in the lldd lacks the call to
nvme_fc_set_remoteport_devloss() to set the value.
Fix by adding the call to the lldd set routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In tests with remote ports contantly logging out/logging coupled with
occassional local link bounce, if a remote port is disocnnected for longer
than devloss_tmo and then subsequently reconnected, eventually the test
will fail to login with the remote port and remote port connectivity is
lost.
When devloss_tmo expires, the driver does not free the node struct until
the port or npiv instances is being deleted. The node is left allocated but
the state set to UNUSED. If the node was in the process of logging in when
the local link drop occurred, meaning the RPI was allocated for the node in
order to send the ELS, but not yet registered which comes after successful
login, the node is moved to the NPR state, and if devloss expires, to
UNUSED state. If the remote port comes back, the node associated with it
is restarted and this path happens to allocate a new RPI and overwrites the
prior RPI value. In the cases where the port was logged in and loggs out,
the path did release the RPI but did not set the node rpi value. In the
cases where the remote port never finished logging in, the path never did
the call to release the rpi. In this latter case, when the node is
subsequently restore, the new rpi allocation overwrites the rpi that was
not released, and the rpi is now leaked. Eventually the port will run out
of RPI resources to log into new remote ports.
Fix by following changes:
- When an rpi is released, do so under locks and ensure the node rpi value
is set to a non-allocated value (LPFC_RPI_ALLOC_ERROR). Note:
refactored to a small service routine to avoid indentation issues.
- When re-enabling a node, check the rpi value to determine if a new
allocation is necessary. If already set, use the prior rpi.
Enhanced logging to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a remote port is removed and remains removed for devloss_tmo, if an RSCN
is subsequently received indicating the presence of the remte port, the
driver does not login to and rediscovery the remote port.
Currently, in order to for a port to be rediscovered post an RSCN, the node
state must be NPR to reflect not logged in. When devloss expires, the node
state is marked UNUSED. When an RSCN occurs, the nodes referenced by the
RSCN will have a NPR_2B_DISC flag set, but the re-login will only be
attempted if the node is in NPR_NODE state. Thus the node is skipped over.
Fix by recognizing the NPR_2B_DISC and UNUSED and transition the node back
to NPR state to allow the re-login to take place.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an admin updates lpfc's devloss_tmo sysfs attribute, the kernel will
oops.
Coding of a loop allowed a new value (rport) to be set/checked for null
followed by an older value (remoteport) checked for null to allow progress
where the new value, even though null, will be referenced.
Rework the logic to validate and prevent any reference to the null ptr.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's possible for the driver to initiate an FLOGI and before it completes,
another link down/up transition occurs requiring a new FLOGI. Currently,
nothing is done to abort/noop the older FLOGI request to the adapter, so if
this transition occurs and the FLOGI completion is received after the link
down/up transition, the driver may erroneously act on the older FLOGI. In
most cases, the adapter properly terminates/fails the FLOGI, but there is a
timing condition where the FLOGI may complete on the wire prior to the
transition, but the response may not be seen/processed by the driver before
the driver sees the link transition.
Fix by having the link down handler in the driver run through any
outstanding ELS's and change the completion handler of the ELS so that it
will be no-op'd and released.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When tearing down the adapter for a reset, online/offline, or driver
unload, the queue free routine would hit a GPF oops. This only occurs on
conditions where the number of hardware queues created is fewer than the
number of cpus in the system. In this condition cpus share a hardware
queue. And of course, it's the 2nd cpu that shares a hardware that
attempted to free it a second time and hit the oops.
Fix by reworking the cpu to hardware queue mapping such that:
Assignment of hardware queues to cpus occur in two passes:
first pass: is first time assignment of a hardware queue to a cpu.
This will set the LPFC_CPU_FIRST_IRQ flag for the cpu.
second pass: for cpus that did not get a hardware queue they will
be assigned one from a primary cpu (one set in first pass).
Deletion of hardware queues is driven by cpu itteration, and queues
will only be deleted if the LPFC_CPU_FIRST_IRQ flag is set.
Also contains a few small cleanup fixes and a little better logging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter reset path (lpfc_sli_hba_down) is taking/releasing a lock with
irq. But, the path is already under the hbalock which raised irq so it's
unnecessary.
Convert to simple lock/unlock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_nvme_register_port hit a null prev_ndlp pointer in a test with lots of
target ports swapping addresses. The oldport value was stale, thus it's
ndlp (prev_ndlp set to it) was used.
Fix by moving oldrport pointer checks, and if used prev_ndlp pointer
assignment, to be done while the lock is held.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is inadvertently trying to issue an INIT_VPI mailbox command on
an SLI-3 driver. The command is specific to SLI-4. When the call is made to
send the command, if on an SLI-3 adapter, an array pointer is NULL and the
driver will oops.
Fix by restricting the command to SLI-4 adapters only.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a target issues an ADISC to the port and the target is a NVME target,
the driver is inadvertantly invalidating the login and marking the remote
port as logged out. Communication with the target is lost.
Revise the ADISC check so that FCP or NVME targets will be marked valid at
the end of ADISC processing. Enhance logging to recognize condition
better.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some remote ports may be slow in registering their GID_FT protocol
information with the fabric. If the remote port is an initiator, it may
send PLOGI to the port before the GID_FT logic is complete. Meaning, after
accepting the PLOGI, when the driver may see no response to the GID_FT that
is issued after the login to determine the protocols supported so that
proper PRLI's may be transmit. If the driver has no fc4 information, it
currently stops and the remote port is not discovered.
Fix by issuing a LOGO when there is no GID_FT information. The LOGO
completion handling will attempt to re-login if the nport_id is still
present.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In cases of remote-port-side cable pull/replug, there happens to be a
target that upon replug will send the port a PLOGI, a PRLI, and a LOGO.
When this sequence is received by the driver, the PLOGI accepted and a
GFT_ID is issued to find the protocol support for the remote port. While
the GFT_ID is outstanding, a LOGO is received. The driver logs the remote
port out and unregisters the RPI and schedules a new PLOGI transmission.
However, the GFT_ID was not terminated. When it completed, the driver
attempted to transition the remote port to PRLI transmission, which cancels
the PLOGI scheduling. The PRLI transmit attempt is rejected by the adapter
as the remote port is not logged in. No retry is attempted as it's expected
the logout is noted and the supposedly scheduled PLOGI should address the
state. As there is no PLOGI, the remote port does not get re-discovered.
Fix by aborting the outstanding GFT_ID if the related remote port is logged
out.
Ensure a PRLI transmit attempt only occurs if the remote port is logging
in. This avoids the incorrect attempt while logged out.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter is reset while there are outstanding ELS's, subsequent
reinitialization of the adapter will fail as it has not recovered all of
the io contexts relative to the ELS's.
If an ELS timed out or otherwise failed and an the ELS was attempted to be
aborted (which changes the ELS completion context), in causes where the
driver generates completions for the outstanding IO as the adapter would
not due to being reset, the driver released only the ELS context and failed
to release the abort context. When the adapter went to reinit, as it had
not received all of the contexts, it failed to reinit.
Fix by having the ELS completion handler identify the driver-generated
completion status and release the abort context.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unusually high IO latency can be observed with little IO in progress. The
latency may remain high regardless of amount of IO and can only be cleared
by forcing lpfc_fcp_imax values to non-zero and then back to zero.
The driver's eq_delay mechanism that scales the interrupt coalescing based
on io completion load failed to reduce or turn off coalescing when load
decreased. Specifically, if no io completed on a cpu within an eq_delay
polling window, the eq delay processing was skipped and no change was made
to the coalescing values. This left the coalescing values set when they
were no longer applicable.
Fix by always clearing the percpu counters for each time period and always
run the eq_delay calculations if an eq has a non-zero coalescing value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a timer routine uses workqueues, it could fire before the workqueue is
allocated.
Fix by allocating the workqueue before the timer routines are setup
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After seeing some interoperability issues with ADISC, it was determined the
ELS definitions in lpfc were using types that allowed the compiler to add
pad to the structure, causing the structure to no longer be per spec. The
offending structures are ADISC, FAN, and RNID.
This patch implements the simple fix of eliminating the pad by forcing the
compiler to pack the structure. Care was taken to ensure field accesses
won't be by operations that would hit a bad field alignment.
The better solution would be to convert to the uapi fc header definitions,
but the number of changes required to do is rather intrusive so this course
of action was deferred.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When connected to a high number of remote ports, the driver is encountering
PLOGI errors. The errors are due to adapter detected failures indicating
illegal field values.
Turns out the driver was prematurely clearing an RPI bitmask before waiting
for an UNREG_RPI mailbox completion. This allowed the RPI to be reused
before it was actually available.
Fix by clearing RPI bitmask only after UNREG_RPI mailbox completion.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi-mq operation inherently performs pre-allocation of resources for
blk-mq request queues. Even though the kdump environment reduces the
configuration to a single CPU, thus 1 hardware queue, which helps
significantly, the resources are still rather large due to the per request
allocations. blk-mq pre-allocations can be over 4KB per request. With
adapter can_queue values in the 4k or 8k range, this can easily be 32MBs
before any other driver memory is factored in. Driver SGL DMA buffer
allocation can be up to 8KB per request as well adding an additional
64MB. Totals are well over 100MB for a single shost. Given kdump memory
auto-sizing utilities don't accommodate this amount of memory well, it's
very possible for kdump to fail due to lack of memory.
Fix by having the driver recognize that it is booting within a kdump
context and reduce the number of requests it will support to a more
reasonable value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As dma_pool_destroy and mempool_destroy functions has NULL check. We may
not need NULL check before calling them.
Fix below warnings reported by coccicheck
./drivers/scsi/lpfc/lpfc_mem.c:252:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:255:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:258:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:261:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:265:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:269:2-17: WARNING: NULL check before some
freeing functions is not needed.
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SCSI-MQ is enabled, the SCSI-MQ layers will do pre-allocation of MQ
resources based on shost values set by the driver. In newer cases of the
driver, which attempts to set nr_hw_queues to the cpu count, the
multipliers become excessive, with a single shost having SCSI-MQ
pre-allocation reaching into the multiple GBytes range. NPIV, which
creates additional shosts, only multiply this overhead. On lower-memory
systems, this can exhaust system memory very quickly, resulting in a system
crash or failures in the driver or elsewhere due to low memory conditions.
After testing several scenarios, the situation can be mitigated by limiting
the value set in shost->nr_hw_queues to 4. Although the shost values were
changed, the driver still had per-cpu hardware queues of its own that
allowed parallelization per-cpu. Testing revealed that even with the
smallish number for nr_hw_queues for SCSI-MQ, performance levels remained
near maximum with the within-driver affiinitization.
A module parameter was created to allow the value set for the nr_hw_queues
to be tunable.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As spin_unlock_irq will enable interrupts.
Function lpfc_findnode_rpi is called from
lpfc_sli_abts_err_handler (./drivers/scsi/lpfc/lpfc_sli.c)
<- lpfc_sli_async_event_handler
<- lpfc_sli_process_unsol_iocb
<- lpfc_sli_handle_fast_ring_event
<- lpfc_sli_fp_intr_handler
<- lpfc_sli_intr_handler
and lpfc_sli_intr_handler is an interrupt handler.
Interrupts are enabled in interrupt handler. Use
spin_lock_irqsave/spin_unlock_irqrestore instead of spin_(un)lock_irq in
IRQ context to avoid this.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the redundant initialization code.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a configurations runs with a single cpu (such as a kdump kernel),
which causes the driver to request a single vector, when the driver
subsequently requests an irq affinity mask, the mask comes back null. The
driver currently does nothing in this scenario, which leaves mappings to
hardware queues incomplete and crashes the system.
Fix by recognizing the null mask and assigning the vector to the first cpu
in the system.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A null check before a kfree is redundant, so remove it. This is detected
by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note
is adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXTJS/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQTNAQCsTdkA
IN1BvDBbE+KO8mvL5DuRxLtnDU6Pq5K6fkrE3gD/a1GkqyPPaJIuspq7fQY87DH/
o7VsJd/5uGphIE2Ls+M=
=38XV
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note is
adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: megaraid_sas: set an unlimited max_segment_size
scsi: mpt3sas: set an unlimited max_segment_size for SAS 3.0 HBAs
scsi: IB/srp: set virt_boundary_mask in the scsi host
scsi: IB/iser: set virt_boundary_mask in the scsi host
scsi: storvsc: set virt_boundary_mask in the scsi host template
scsi: ufshcd: set max_segment_size in the scsi host template
scsi: core: take the DMA max mapping size into account
scsi: core: add a host / host template field for the virt boundary
scsi: core: Fix race on creating sense cache
scsi: sd_zbc: Fix compilation warning
scsi: libfc: fix null pointer dereference on a null lport
scsi: zfcp: fix GCC compiler warning emitted with -Wmaybe-uninitialized
scsi: zfcp: fix request object use-after-free in send path causing wrong traces
scsi: zfcp: fix request object use-after-free in send path causing seqno errors
scsi: megaraid_sas: Update driver version to 07.710.50.00
scsi: megaraid_sas: Add module parameter for FW Async event logging
scsi: megaraid_sas: Enable msix_load_balance for Invader and later controllers
scsi: megaraid_sas: Fix calculation of target ID
scsi: lpfc: reduce stack size with CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE
scsi: devinfo: BLIST_TRY_VPD_PAGES for SanDisk Cruzer Blade
...
Merge updates from Andrew Morton:
"Am experimenting with splitting MM up into identifiable subsystems
perhaps with a view to gitifying it in complex ways. Also with more
verbose "incoming" emails.
Most of MM is here and a few other trees.
Subsystems affected by this patch series:
- hotfixes
- iommu
- scripts
- arch/sh
- ocfs2
- mm:slab-generic
- mm:slub
- mm:kmemleak
- mm:kasan
- mm:cleanups
- mm:debug
- mm:pagecache
- mm:swap
- mm:memcg
- mm:gup
- mm:pagemap
- mm:infrastructure
- mm:vmalloc
- mm:initialization
- mm:pagealloc
- mm:vmscan
- mm:tools
- mm:proc
- mm:ras
- mm:oom-kill
hotfixes:
mm: vmscan: scan anonymous pages on file refaults
mm/nvdimm: add is_ioremap_addr and use that to check ioremap address
mm/memcontrol: fix wrong statistics in memory.stat
mm/z3fold.c: lock z3fold page before __SetPageMovable()
nilfs2: do not use unexported cpu_to_le32()/le32_to_cpu() in uapi header
MAINTAINERS: nilfs2: update email address
iommu:
include/linux/dmar.h: replace single-char identifiers in macros
scripts:
scripts/decode_stacktrace: match basepath using shell prefix operator, not regex
scripts/decode_stacktrace: look for modules with .ko.debug extension
scripts/spelling.txt: drop "sepc" from the misspelling list
scripts/spelling.txt: add spelling fix for prohibited
scripts/decode_stacktrace: Accept dash/underscore in modules
scripts/spelling.txt: add more spellings to spelling.txt
arch/sh:
arch/sh/configs/sdk7786_defconfig: remove CONFIG_LOGFS
sh: config: remove left-over BACKLIGHT_LCD_SUPPORT
sh: prevent warnings when using iounmap
ocfs2:
fs: ocfs: fix spelling mistake "hearbeating" -> "heartbeat"
ocfs2/dlm: use struct_size() helper
ocfs2: add last unlock times in locking_state
ocfs2: add locking filter debugfs file
ocfs2: add first lock wait time in locking_state
ocfs: no need to check return value of debugfs_create functions
fs/ocfs2/dlmglue.c: unneeded variable: "status"
ocfs2: use kmemdup rather than duplicating its implementation
mm:slab-generic:
Patch series "mm/slab: Improved sanity checking":
mm/slab: validate cache membership under freelist hardening
mm/slab: sanity-check page type when looking up cache
lkdtm/heap: add tests for freelist hardening
mm:slub:
mm/slub.c: avoid double string traverse in kmem_cache_flags()
slub: don't panic for memcg kmem cache creation failure
mm:kmemleak:
mm/kmemleak.c: fix check for softirq context
mm/kmemleak.c: change error at _write when kmemleak is disabled
docs: kmemleak: add more documentation details
mm:kasan:
mm/kasan: print frame description for stack bugs
Patch series "Bitops instrumentation for KASAN", v5:
lib/test_kasan: add bitops tests
x86: use static_cpu_has in uaccess region to avoid instrumentation
asm-generic, x86: add bitops instrumentation for KASAN
Patch series "mm/kasan: Add object validation in ksize()", v3:
mm/kasan: introduce __kasan_check_{read,write}
mm/kasan: change kasan_check_{read,write} to return boolean
lib/test_kasan: Add test for double-kzfree detection
mm/slab: refactor common ksize KASAN logic into slab_common.c
mm/kasan: add object validation in ksize()
mm:cleanups:
include/linux/pfn_t.h: remove pfn_t_to_virt()
Patch series "remove ARCH_SELECT_MEMORY_MODEL where it has no effect":
arm: remove ARCH_SELECT_MEMORY_MODEL
s390: remove ARCH_SELECT_MEMORY_MODEL
sparc: remove ARCH_SELECT_MEMORY_MODEL
mm/gup.c: make follow_page_mask() static
mm/memory.c: trivial clean up in insert_page()
mm: make !CONFIG_HUGE_PAGE wrappers into static inlines
include/linux/mm_types.h: ifdef struct vm_area_struct::swap_readahead_info
mm: remove the account_page_dirtied export
mm/page_isolation.c: change the prototype of undo_isolate_page_range()
include/linux/vmpressure.h: use spinlock_t instead of struct spinlock
mm: remove the exporting of totalram_pages
include/linux/pagemap.h: document trylock_page() return value
mm:debug:
mm/failslab.c: by default, do not fail allocations with direct reclaim only
Patch series "debug_pagealloc improvements":
mm, debug_pagelloc: use static keys to enable debugging
mm, page_alloc: more extensive free page checking with debug_pagealloc
mm, debug_pagealloc: use a page type instead of page_ext flag
mm:pagecache:
Patch series "fix filler_t callback type mismatches", v2:
mm/filemap.c: fix an overly long line in read_cache_page
mm/filemap: don't cast ->readpage to filler_t for do_read_cache_page
jffs2: pass the correct prototype to read_cache_page
9p: pass the correct prototype to read_cache_page
mm/filemap.c: correct the comment about VM_FAULT_RETRY
mm:swap:
mm, swap: fix race between swapoff and some swap operations
mm/swap_state.c: simplify total_swapcache_pages() with get_swap_device()
mm, swap: use rbtree for swap_extent
mm/mincore.c: fix race between swapoff and mincore
mm:memcg:
memcg, oom: no oom-kill for __GFP_RETRY_MAYFAIL
memcg, fsnotify: no oom-kill for remote memcg charging
mm, memcg: introduce memory.events.local
mm: memcontrol: dump memory.stat during cgroup OOM
Patch series "mm: reparent slab memory on cgroup removal", v7:
mm: memcg/slab: postpone kmem_cache memcg pointer initialization to memcg_link_cache()
mm: memcg/slab: rename slab delayed deactivation functions and fields
mm: memcg/slab: generalize postponed non-root kmem_cache deactivation
mm: memcg/slab: introduce __memcg_kmem_uncharge_memcg()
mm: memcg/slab: unify SLAB and SLUB page accounting
mm: memcg/slab: don't check the dying flag on kmem_cache creation
mm: memcg/slab: synchronize access to kmem_cache dying flag using a spinlock
mm: memcg/slab: rework non-root kmem_cache lifecycle management
mm: memcg/slab: stop setting page->mem_cgroup pointer for slab pages
mm: memcg/slab: reparent memcg kmem_caches on cgroup removal
mm, memcg: add a memcg_slabinfo debugfs file
mm:gup:
Patch series "switch the remaining architectures to use generic GUP", v4:
mm: use untagged_addr() for get_user_pages_fast addresses
mm: simplify gup_fast_permitted
mm: lift the x86_32 PAE version of gup_get_pte to common code
MIPS: use the generic get_user_pages_fast code
sh: add the missing pud_page definition
sh: use the generic get_user_pages_fast code
sparc64: add the missing pgd_page definition
sparc64: define untagged_addr()
sparc64: use the generic get_user_pages_fast code
mm: rename CONFIG_HAVE_GENERIC_GUP to CONFIG_HAVE_FAST_GUP
mm: reorder code blocks in gup.c
mm: consolidate the get_user_pages* implementations
mm: validate get_user_pages_fast flags
mm: move the powerpc hugepd code to mm/gup.c
mm: switch gup_hugepte to use try_get_compound_head
mm: mark the page referenced in gup_hugepte
mm/gup: speed up check_and_migrate_cma_pages() on huge page
mm/gup.c: remove some BUG_ONs from get_gate_page()
mm/gup.c: mark undo_dev_pagemap as __maybe_unused
mm:pagemap:
asm-generic, x86: introduce generic pte_{alloc,free}_one[_kernel]
alpha: switch to generic version of pte allocation
arm: switch to generic version of pte allocation
arm64: switch to generic version of pte allocation
csky: switch to generic version of pte allocation
m68k: sun3: switch to generic version of pte allocation
mips: switch to generic version of pte allocation
nds32: switch to generic version of pte allocation
nios2: switch to generic version of pte allocation
parisc: switch to generic version of pte allocation
riscv: switch to generic version of pte allocation
um: switch to generic version of pte allocation
unicore32: switch to generic version of pte allocation
mm/pgtable: drop pgtable_t variable from pte_fn_t functions
mm/memory.c: fail when offset == num in first check of __vm_map_pages()
mm:infrastructure:
mm/mmu_notifier: use hlist_add_head_rcu()
mm:vmalloc:
Patch series "Some cleanups for the KVA/vmalloc", v5:
mm/vmalloc.c: remove "node" argument
mm/vmalloc.c: preload a CPU with one object for split purpose
mm/vmalloc.c: get rid of one single unlink_va() when merge
mm/vmalloc.c: switch to WARN_ON() and move it under unlink_va()
mm/vmalloc.c: spelling> s/informaion/information/
mm:initialization:
mm/large system hash: use vmalloc for size > MAX_ORDER when !hashdist
mm/large system hash: clear hashdist when only one node with memory is booted
mm:pagealloc:
arm64: move jump_label_init() before parse_early_param()
Patch series "add init_on_alloc/init_on_free boot options", v10:
mm: security: introduce init_on_alloc=1 and init_on_free=1 boot options
mm: init: report memory auto-initialization features at boot time
mm:vmscan:
mm: vmscan: remove double slab pressure by inc'ing sc->nr_scanned
mm: vmscan: correct some vmscan counters for THP swapout
mm:tools:
tools/vm/slabinfo: order command line options
tools/vm/slabinfo: add partial slab listing to -X
tools/vm/slabinfo: add option to sort by partial slabs
tools/vm/slabinfo: add sorting info to help menu
mm:proc:
proc: use down_read_killable mmap_sem for /proc/pid/maps
proc: use down_read_killable mmap_sem for /proc/pid/smaps_rollup
proc: use down_read_killable mmap_sem for /proc/pid/pagemap
proc: use down_read_killable mmap_sem for /proc/pid/clear_refs
proc: use down_read_killable mmap_sem for /proc/pid/map_files
mm: use down_read_killable for locking mmap_sem in access_remote_vm
mm: smaps: split PSS into components
mm: vmalloc: show number of vmalloc pages in /proc/meminfo
mm:ras:
mm/memory-failure.c: clarify error message
mm:oom-kill:
mm: memcontrol: use CSS_TASK_ITER_PROCS at mem_cgroup_scan_tasks()
mm, oom: refactor dump_tasks for memcg OOMs
mm, oom: remove redundant task_in_mem_cgroup() check
oom: decouple mems_allowed from oom_unkillable_task
mm/oom_kill.c: remove redundant OOM score normalization in select_bad_process()"
* akpm: (147 commits)
mm/oom_kill.c: remove redundant OOM score normalization in select_bad_process()
oom: decouple mems_allowed from oom_unkillable_task
mm, oom: remove redundant task_in_mem_cgroup() check
mm, oom: refactor dump_tasks for memcg OOMs
mm: memcontrol: use CSS_TASK_ITER_PROCS at mem_cgroup_scan_tasks()
mm/memory-failure.c: clarify error message
mm: vmalloc: show number of vmalloc pages in /proc/meminfo
mm: smaps: split PSS into components
mm: use down_read_killable for locking mmap_sem in access_remote_vm
proc: use down_read_killable mmap_sem for /proc/pid/map_files
proc: use down_read_killable mmap_sem for /proc/pid/clear_refs
proc: use down_read_killable mmap_sem for /proc/pid/pagemap
proc: use down_read_killable mmap_sem for /proc/pid/smaps_rollup
proc: use down_read_killable mmap_sem for /proc/pid/maps
tools/vm/slabinfo: add sorting info to help menu
tools/vm/slabinfo: add option to sort by partial slabs
tools/vm/slabinfo: add partial slab listing to -X
tools/vm/slabinfo: order command line options
mm: vmscan: correct some vmscan counters for THP swapout
mm: vmscan: remove double slab pressure by inc'ing sc->nr_scanned
...
The RISC-V architecture has a register named the "Supervisor Exception
Program Counter", or "sepc". This abbreviation triggers checkpatch.pl's
misspelling detector, resulting in noise in the checkpatch output. The
risk that this noise could cause more useful warnings to be missed seems
to outweigh the harm of an occasional misspelling of "spec". Thus drop
the "sepc" entry from the misspelling list.
[akpm@linux-foundation.org: fix existing "sepc" instances, per Joe]
Link: http://lkml.kernel.org/r/20190518210037.13674-1-paul.walmsley@sifive.com
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lpfc_debug_dump_all_queues() function repeatedly calls into
lpfc_debug_dump_qe() which has a temporary 128 byte buffer. This was fine
before the introduction of CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE because
each instance could occupy the same stack slot. However, now they each get
their own copy, which leads to a huge increase in stack usage as seen from
the compiler warning:
drivers/scsi/lpfc/lpfc_debugfs.c: In function 'lpfc_debug_dump_all_queues':
drivers/scsi/lpfc/lpfc_debugfs.c:6474:1: error: the frame size of 1712 bytes is larger than 100 bytes [-Werror=frame-larger-than=]
Avoid this by not marking lpfc_debug_dump_qe() as inline so the compiler
can choose to emit a static version of this function when it's needed or
otherwise silently drop it. As an added benefit, not inlining multiple
copies of this function means we save several kilobytes of .text section,
reducing the file size from 47kb to 43.
It is somewhat unusual to have a function that is static but not inline in
a header file, but this does not cause problems here because it is only
used by other inline functions. It would however seem reasonable to move
all the lpfc_debug_dump_* functions into lpfc_debugfs.c and not mark them
inline as a later cleanup.
Fixes: 81a56f6dcd ("gcc-plugins: structleak: Generalize to all variable types")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list. This necessitates a large number of driver
changes because the previous guarantee that if a driver specified
SG_ALL as the size of its scatter list, it would get a non-chained
list and didn't need to bother with scatterlist iterators is now
broken and every driver *must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTzzCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZB+AP9I8j/s
wWfg0Z3WNuf4D5I3rH4x1J3cQTqPJed+RjwgcQEA1gZvtOTg1ZEn/CYMVnaB92x0
t6MZSchIaFXeqfD+E7U=
=cv8o
-----END PGP SIGNATURE-----
Merge tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI scatter-gather list updates from James Bottomley:
"This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list.
This necessitates a large number of driver changes because the
previous guarantee that if a driver specified SG_ALL as the size of
its scatter list, it would get a non-chained list and didn't need to
bother with scatterlist iterators is now broken and every driver
*must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase"
* tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
scsi: core: don't preallocate small SGL in case of NO_SG_CHAIN
scsi: lib/sg_pool.c: clear 'first_chunk' in case of no preallocation
scsi: core: avoid preallocating big SGL for data
scsi: core: avoid preallocating big SGL for protection information
scsi: lib/sg_pool.c: improve APIs for allocating sg pool
scsi: esp: use sg helper to iterate over scatterlist
scsi: NCR5380: use sg helper to iterate over scatterlist
scsi: wd33c93: use sg helper to iterate over scatterlist
scsi: ppa: use sg helper to iterate over scatterlist
scsi: pcmcia: nsp_cs: use sg helper to iterate over scatterlist
scsi: imm: use sg helper to iterate over scatterlist
scsi: aha152x: use sg helper to iterate over scatterlist
scsi: s390: zfcp_fc: use sg helper to iterate over scatterlist
scsi: staging: unisys: visorhba: use sg helper to iterate over scatterlist
scsi: usb: image: microtek: use sg helper to iterate over scatterlist
scsi: pmcraid: use sg helper to iterate over scatterlist
scsi: ipr: use sg helper to iterate over scatterlist
scsi: mvumi: use sg helper to iterate over scatterlist
scsi: lpfc: use sg helper to iterate over scatterlist
scsi: advansys: use sg helper to iterate over scatterlist
...
This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTl4yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdcxAQDCJVbd
fPUX76/V1ldupunF97+3DTharxxbst+VnkOnCwD8D4c0KFFFOI9+F36cnMGCPegE
fjy17dQLvsJ4GsidHy8=
=aS5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
To support scenarios which aren't bound to nvmetcli add port scenarios,
which is currently where the nvmet_fc transport invokes the discovery
event callbacks, a syfs attribute is added to lpfc which can be written
to cause an RSCN to be generated for the nport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch updates RSCN receive processing to check for the remote
port being an NVME port, and if so, invoke the nvme_fc callback to
rescan the remote port. The rescan will generate a discovery udev
event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds support for the nvmet discovery op. When the callback
routine is called, the driver will call the routine to generate an RSCN
to the port on the other end of the link.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds general RSCN support:
- The ability to transmit an RSCN to the port on the other end of
the link (regular port if pt2pt, or fabric controller if fabric).
- And general recognition of an RSCN ELS when an ELS is received.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Reviewed by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building powerpc pseries_defconfig or powernv_defconfig:
drivers/scsi/lpfc/lpfc_nvmet.c:224:1: error: unused function
'lpfc_nvmet_get_ctx_for_xri' [-Werror,-Wunused-function]
drivers/scsi/lpfc/lpfc_nvmet.c:246:1: error: unused function
'lpfc_nvmet_get_ctx_for_oxid' [-Werror,-Wunused-function]
These functions are only compiled when CONFIG_NVME_TARGET_FC is enabled.
Use that same condition so there is no more warning. While the fixes commit
did not introduce these functions, it caused these warnings.
Fixes: 4064b27417a7 ("scsi: lpfc: Make some symbols static")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/lpfc/lpfc_sli.c:115:1: warning: symbol 'lpfc_sli4_pcimem_bcopy' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_sli.c:7854:1: warning: symbol 'lpfc_sli4_process_missed_mbox_completions' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:223:27: warning: symbol 'lpfc_nvmet_get_ctx_for_xri' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:245:27: warning: symbol 'lpfc_nvmet_get_ctx_for_oxid' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_init.c:75:10: warning: symbol 'lpfc_present_cpu' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/scsi/lpfc/lpfc_init.c: In function lpfc_setup_cq_lookup:
drivers/scsi/lpfc/lpfc_init.c:9359:30: warning: variable qp set but not used [-Wunused-but-set-variable]
It's not used since commit e70596a60f88 ("scsi: lpfc: Fix poor use of
hardware queues if fewer irq vectors")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use *_pool_zalloc rather than *_pool_alloc followed by memset with 0.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.3
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kernel warnings may be seen with preempt debugging enabled.
Replace smp_processor_id calls with raw_smp_processor_id or cpu information
stored in hdwq structures.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Crashes in scsi_queue_rq or in dma_unmap_direct_sg during BFS when lpfc has
lpfc_enable_bg=1.
lpfc is setting DIX and prot sg after scsi_add_host_with_dma() has been
called. The scsi_host_set_prot() and scsi_host_set_guard() routines need to
be called before scsi_add_host_with_dma().
Revise the calling sequence to set the protection/guard data before calling
scsi_add_host_with_dma().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FDMI protocol support registration was not accurately showing nvme
support. The fcponly-path clears the parameter object.
Move the code out of the fcponly code path. Fix the FDMI registration data
to properly check for nvme support. Commonize the manner in which the fdmi
routines set protocol support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issuing a LUN reset was resulting in a command failure which then escalated
to a host reset.
The FCP-4 spec allows fcp_rsp_len field to specify the number of valid
bytes of FCP_RSP_INFO, and the value could be 4 or 8. The driver is
allowing only a value of 8, thus it failed the command.
Revise the driver to allow 4 or 8.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While fixing the resources per socket, realized the driver was not using
hardware queues (up to 1 per cpu) if there were fewer interrupt
vectors. The driver was only using the hardware queue assigned to the cpu
with the vector.
Rework the affinity map check to use the additional hardware queue elements
that had been allocated. If the cpu count exceeds the hardware queue count
- share, but choose what is shared with by: hyperthread peer, core peer,
socket peer, or finally similar cpu in a different socket.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver was coded expecting enough hardware queues and interrupt vectors
such that at least there was one per socket. In the case where there were
fewer than sockets, cpus were left unassigned thus null pointers.
Rework the affinity mappings. Map settings for the cpu's that are in the
irq cpu mask. For each cpu not in the mask, map to another cpu that does
have a mask. Choice of the "other" cpu will attempt to map to the same cpu
but differing hyperthread, or cpu within in same core, or cpu within same
socket, or finally cpu in the base socket.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Invalid logical speed is displayed for trunk enabled ports when all ports
are down. Also noted that link speed is incorrectly reported for the units
when links are up.
Current code is returning the logical link speed from the last event from
the adapter. In cases where the last link went down, the link speed in the
event was not valid - meaning that although the links where down the field
had a bogus value.
Rework the event handling to qualify the trunk link state before using the
event speed data.
Also correct units on other areas where the logical link speed was taken
from a link event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
eq create is leaking mailbox memory if it encounters an error.
rework error path to free the memory.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver unconditionally says fw doesn't support nvme when in
truth it was a driver parameter settings that disabled nvme support.
Rework the code validating nvme support to accurately report what
condition is disabling nvme support. Save state on whether nvme
fw supports nvme in case sysfs attributes change dynamically.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a race condition with the abort handler declaring a waitq
item on it's stack, followed by a timeout in the abort handler that
has it give up on the abort return to its caller. When the io is
finally aborted and its completion handler called, it references
the waitq element that the abort_handler set up, which is no longer
valid resulting in a deadlock.
Fix by clearing the waitq reference, under lock, when the abort
handler timeout gives up. Have the completion handler validate the
waitq before referencing it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When queued work is executed posting a new command to the transport
the driver is reporting a null buffer.
The driver had received an ABTS which matched a command that had
been scheduled for delivery to the transport. The driver proceeded
to cancel the command, but the work item was never cancelled.
Fix by cancelling the queued work item. Also turns out the ABTS
response was not properly sending a BA_ACC, so set the flag to
send the ACC.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use-after-free memory overwrite detected. Problem reported
by Ewan Milne at Red Hat after running lpfc target with additional
memory checking enabled.
Race condition when lpfc_nvmet_xmt_ls_rsp_cmp frees the ctxp
memory in interrupt context before lpfc_nvmet_xmt_ls_rsp
clears a field in the ctxp after successfully issuing the wqe.
Remove the unnecessary ctxp write after reposting the rq buffer. The
ctxp->rqb_buffer field is not checked in LS handling after the wqe
is submitted.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reported-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under heavy load the target stops responding, the drivers aborts
timeout and we start recovery by logging out of the target, but
the target is never logged into again.
In a point-to-point scenario, there were battling PLOGI's. When we
received a PLOGI request after having sent one, the driver cancels
the processing of the original plogi. However, the completion path
of the remaining plogi was coded to skip the reg_rpi that should
be happening on the 2nd plogi.
Correct by adding a simple pt2pt check such that the 2nd plogi isn't
skipped and the reg_login occurs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Turns out the message change in 12.2.0.1 for unsupported topology
makes the linux driver out of sync with other products.
Revert the message back to the prior content for product consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently is relying on firmware to match ABTSs to existing
exchanges. This works fine as long as an exchange has been assigned to the
io and work posted to it. However, for unmapped frames (rxid=0xFFFF), the
driver has yet to assign an xri. The driver was blindly saying it couldn't
match the ABTS and sending the BA_xxx. However, the command frame may have
been in queues waiting on xri's before posting to the nvmet_fc layer. When
xri's became available, the command frame would still be pushed to the
transport and that io would execute, even though the io had been killed by
ABTS. The initiator, seeing the io ABTS'd, would reuse the exchange for a
different io which would be received on the target and pushed up. If the
"zombie" io then came back down and started transmitting, the initiator
would match the oxid and accept erroneous data. Bad things happened.
Add tracking of active exchanges in the target to allow matching of a
received ABTS against active or pending IO requests. If the ABTS is matched
to a pending or active IO, the drive initiates cleanup and conditionally
notifies the transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver is notified of new command frame receipt by CQEs. As
part of the CQE processing, the driver upcalls the nvmet_fc transport to
deliver the command. nvmet_fc, as part of receiving the command builds out
a context for it, where one of the first steps is to allocate memory for
the io.
When running with tests that do large ios (1MB), it was found on some
systems, the total number of outstanding I/O's, at 1MB per, completely
consumed the system's memory. Thus additional ios were getting blocked in
the memory allocator. Given that this blocked the lpfc thread processing
CQEs, there were lots of other commands that were received and which are
then held up, and given CQEs are serially processed, the aggregate delays
for an IO waiting behind the others became cummulative - enough so that the
initiator hit timeouts for the ios.
The basic fix is to avoid the direct upcall and instead schedule a work
item for each io as it is received. This allows the cq processing to
complete very quickly, and each io can then run or block on it's own.
However, this general solution hurts latency when there are few ios. As
such, implemented the fix such that the driver watches how many CQEs it has
processed sequentially in one run. As long as the count is below a
threshold, the direct nvmet_fc upcall will be made. Only when the count is
exceeded will it revert to work scheduling.
Given that debug of this showed a surprisingly long delay in cq processing,
the io timer stats were updated to better reflect the processing of the
different points.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise a stalled adapter message to also include the number of jobs that
are stalling the thread.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A race condition resulted in receive buffers being placed in the free list
twice.
Change the locking and handling to check whether the "other" path will be
freeing the entry in a later thread and skip it if it is.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After receiving an unsolicited ABTS (meaning rxid is 0xFFFF), the driver
used the oxid from the initiator to match against a local xri which may
have been allocated for the io. The xri would be the rxid - it's an invalid
check resulting in the command not being matched or erroneously matched.
Change the lookup to use the oxid and the SID to match against received
IO's original values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Softlockups are seen in low memory situations. They are due to doing
oas_lun allocation with GFP_KERNEL in atomic contexts.
Change the calls to oas_lun to indicate atomic context so that GFP_ATOMIC
is used.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to the couple of bug fixes, update lpfc version to 12.2.0.2
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There was a missing qualification of a valid ndlp structure when calling to
send an RRQ for an abort. Add the check.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many of the exit cases were not releasing the rcu read lock. Corrected the
exit paths.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There were a number of erroneous comments and incorrect older lockdep
checks that were causing a number of warnings.
Resolve the following:
- Inconsistent lock state warnings in lpfc_nvme_info_show().
- Fixed comments and code on sequences where ring lock is now held instead
of hbalock.
- Reworked calling sequences around lpfc_sli_iocbq_lookup(). Rather than
locking prior to the routine and have routine guess on what lock, take
the lock within the routine. The lockdep check becomes unnecessary.
- Fixed comments and removed erroneous hbalock checks.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warning:
drivers/scsi/lpfc/lpfc_init.c:13091:1: warning:
symbol 'lpfc_sli4_oas_verify' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have a few submissions for 5.2 that depend on fixes merged post
5.1-rc1. Merge the fixes branch into queue.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the FC-NVMe driver is leverating the SCSI FC transport class to
access the remote ports. Which means that all FC-NVMe remote ports will be
visible to the fc transport layer, but due to missing definitions the port
roles will always be 'unknown'. This patch adds the missing definitions to
the fc transport class to that the port roles are correctly displayed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support to recognize FPIN ELS's that are received. When
one is received, the fc transport will be called to handle the the FPIN.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the following compiler warning is reported with
CONFIG_NVME_FC=n:
drivers/scsi/lpfc/lpfc_nvme.c:2140:1: warning: 'lpfc_nvme_lport_unreg_wait' defined but not used [-Wunused-function]
lpfc_nvme_lport_unreg_wait(struct lpfc_vport *vport,
^~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 3999df75bc ("scsi: lpfc: Declare local functions static")
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Abort thread wakeups, on some wqe types, are not happening. The thread
wakeup logic is dependent upon the LPFC_DRIVER_ABORTED flag. However, on
these wqes, the completion handler running prior to the io completion
routine ends up clearing the flag.
Rework the wakeup logic to look at a non-null waitq element which must be
set if the abort thread is waiting. This is reverting the change in the
indicated patch.
Fixes: c2017260ee ("scsi: lpfc: Rework locking on SCSI io completion")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that a kernel warning appears when smp_processor_id() is
called with preempt debugging enabled.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove those functions that are not called from outside the removed
functions.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but avoids that the compiler
complains about set-but-not-used variables when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arrays should be defined in .c files instead of in a header file. This
patch reduces the size of the lpfc kernel module.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler warns about missing fall-through
annotation when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoid that smatch complains about misleading indentation.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler complains about missing declarations
when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
clang -Wuninitialized incorrectly sees a variable being used without
initialization:
drivers/scsi/lpfc/lpfc_nvme.c:2102:37: error: variable 'localport' is uninitialized when used here
[-Werror,-Wuninitialized]
lport = (struct lpfc_nvme_lport *)localport->private;
^~~~~~~~~
drivers/scsi/lpfc/lpfc_nvme.c:2059:38: note: initialize the variable 'localport' to silence this warning
struct nvme_fc_local_port *localport;
^
= NULL
1 error generated.
This is clearly in dead code, as the condition leading up to it is always
false when CONFIG_NVME_FC is disabled, and the variable is always
initialized when nvme_fc_register_localport() got called successfully.
Change the preprocessor conditional to the equivalent C construct, which
makes the code more readable and gets rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the
buffer size (SIZE) is, then size will end up larger than SIZE. In later
uses of snprintf, SIZE - size will result in a negative number, leading
to problems. Note that size might already be too large by using
size = snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to user
space, then it will potentially allow for a buffer overflow and information
disclosure when size is greater than SIZE. When the size is used to index
the buffer directly, we can have memory corruption. This also means when
size = snprintf... is used, it may also cause problems since size may become
large. Copying to userspace is mitigated by the HARDENED_USERCOPY kernel
configuration.
The solution to these issues is to use scnprintf which returns the number of
characters actually written to the buffer, so the size variable will never
exceed SIZE.
Signed-off-by: Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Declaring interrupt clear routines as inline is bogus as they are used as
an indirect pointer.
Remove the inline references.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
You can't declare a function inline in a header if it doesn't have a body
available to the compiler. So realistically you either don't declare it
inline or you make it a static inline in the header. I think the latter
applies in this case, so this should be the fix
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise driver copyright message to show 2019. Update couple of files
modified by 12.2.0.1 patch set.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the 6072 log message string to print the whole 32 bits of the
extended status.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver had duplicated log message numbers making debug difficult.
Make all messages unique.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change the SLI4 queue creation code to use NUMA node based memory
allocation based on the cpu the queues will be related to.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver maintains a sideband structure which has a pointer for
each queue element. However, at 8 bytes per pointer, and up to 4k elements
per queue, and 100s of queues, this can take up a lot of memory.
Convert the driver to using an access routine that calculates the element
address based on its index rather than using the pointer table.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When in trunking mode, the adapter can be placed into diagnostic mode and
each link in the trunk tested via loopback.
Add support to the driver to perform per-link loopback testing when in
trunking mode.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is using uint16_t and is encountering an overflow of the 16bits when
calculating link speed.
Fix by using a u32 type.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If all the trunk links drop and a single link resumes, the link_state is
not properly reported. When trunked, the driver receives two async
cqes. One acqe reports the trunk link states, which the driver records.
The other cqe reports the overall state of the trunk. In the failing case,
the trunk link state acqe preceeds the overall trunk link state acqe. The
trunk link state acqe, as it's an "up" transition, calls a code path which
ensures a down transition before moving to the up state. The down
transition had a side effect of clearing the just-saved trunk link states.
Fix by not clearing the trunk link states if we've already transitioned
to a down state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Invalid test is allowing Loop to be a supported topology on G6 and G7
adapters. The chips do not support loop as their link speeds prohibit loop
per standard.
Correct the conditional so that loop is not reported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently reporting the firmware revision not the actual boot
bios version in FDMI data.
Modify the driver to obtain the boot bios version from the adapter and use
that data in the FMDI data sent to the switch.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The switch is rejecting FDMI2 registration for symbolic name. There is a
"\n" in the name string, which the switch dislikes thus rejects the
registration.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is reporting support for NVME even when not configured for NVME
operation.
Fix (and make more readable) when NVME protocol support is indicated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The FDMI manufacturer value being reported on Linux is inconsistent with
other OS's.
Set the value to "Emulex Corporation" for consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the driver undergoes repeated host resets it starts losing exchange
structures and eventually returns SCSI_MLQUEUE_HOST_BUSY and does not
recover. The offline path is not reclaiming the outstanding ios on the fcp
pring txcmplq before calling lpfc_destroy_multixripool, which causes the
txmcplq to be reinit and the resources lost.
Flush the fcp rings before destroying the multixripools.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter initialization sequence enables interrupts, initializes the
adapter link_state to LINK_DOWN, then issues commands to initialize the
adapter. The interrupt handler on the adapter validates the link_state (has
to be at least LINK_DOWN) and if invalid, will discard the interrupting
event.
In most cases, there is not a command completion, thus an interrupt until
the initialization commands have been sent which is post the setting of
state to LINK_DOWN. However, in cases of firmware reset, the reset will
modify the link_state to an invalid value (indicating a reset of the
adapter) and there occasionally are cases where the adapter will generate
an asynchronous event which shares the eq/cq used for mailbox commands. In
the failure case, an interrupt is generated immediately after enabling them
due to the async event. As link_state is invalid, the eq is list and the
CQ not serviced. At this point link_state is initialized and the mailbox
command sent. As the CQ has not been serviced, it is not armed, so no
interrupt event is generated when the mailbox command completes.
Modify the initialization sequence so that interrupts are enabled after
link_state is properly initialized, which avoids the race condition with
the async event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's possible for the scsi error handler to fire and call the target reset
handler simultaneously to the driver logging out and relogging into the
system. If hit just right, the re-login may not have fully re-established
the remote port and the rdata->pnod structure may be null.
Check for NULL in the reset handler and return failure if NULL.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code incorrectly specifies a completion wait timeout duration in 5
jiffies, when it should have been 5 seconds.
Fix the adjust for units for the completion timeout call.
[mkp: manual merge]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code is using msleep when polling for hw ready. Unfortunately the
msleep routine isn't very accurate on rescheduling. In fact, on a busy
systems which reset the adapter, it became 10s of seconds before it was
rescheduled.
Fix by busy waiting using udelay. As we're now busy waiting, significantly
reduce the wait time so that we can exit the pool loop as soon as possible.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver periodically checks for adapter error in a background thread. If
the thread detects an error, the adapter will be reset including the
deletion and reallocation of workqueues on the adapter. Simultaneously,
there may be a user-space request to offline the adapter which may try to
do many of the same steps, in parallel, on a different thread. As memory
was deallocated while unexpected, the parallel offline request hit a bad
pointer.
Add coordination between the two threads. The error recovery thread has
precedence. So, when an error is detected, a flag is set on the adapter to
indicate the error thread is terminating the adapter. But, before doing
that work, it will look for a flag that is set by the offline flow, and if
set, will wait for it to complete before then processing the error handling
path. Similarly, in the offline thread, it first checks for whether the
error thread is resetting the adapter, and if so, will then wait for the
error thread to finish. Only after it has finished, will it set its flag
and offline the adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a couple of cases, the driver detected a pci error (via pci device state
or via failed register reads) but didn't take any action to disable the
device. Additionally, the driver is ignoring the status of pci
configuration space reads.
Having the driver take the adapter offline whenever the pci error is
detected. Pay attention to pci_config_space_read status and return failure
if an error is seen.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an adapter fails, causing a board reset, the board reset routine
lpfc_hba_down_s4() takes the hbalock out then calls
lpfc_nvmet_ctxbuf_post() who then tries to take out the same lock. As the
context lists are now protected under the buf_list_locks, there is no need
for the hbalock to be held by the board reset routine.
Fix by no longer taking the hbalock in the board reset routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With negative test injection, the driver is receiving a command with first
burst enabled, meaning Sequence initiative is not passed with the command
frame. The driver notes the condition and discards the frame. However the
driver calls the incorrect buffer free routine, resulting in a NULL pointer
reference.
For hbq buffer free, convert to using lpfc_rq_buf_free().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, when lpfc_nvmet_mrq is 0 it could mean 2 different things
depending on when its looked at. If at module load time it specifies the
default number of hardware queues to allocate, with 0 meaning default to
the number of CPUs. But post module load, a value of zero means to disable
mrq use.
Changed the driver so that enablement of mrq is based on whether nvme
target mode is enabled or not. When enabled, mrq is enabled. Thus, the
cfg_nvemt_mrq field only specifies the number of mrq queues to enable, with
0 defaulting to the number of cpus.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under circustances with high load, the driver is running out of async
receive buffers which may result in one of the following messages:
0:6401 RQE Error x13, posted 226 err_cnt 0: 925c6050 925c604e 925c5d54
or
0:2885 Port Status Event: port status reg 0x81800000,
port smphr reg 0xc000, error 1=0x52004a01, error 2=0x0
The driver is waiting for full io completion before returning receive
buffers to the adapter. There is no need for such a relationship.
Whenever a new command is received from the wire, the driver will have two
contexts - an io context (ctxp) and a receive buffer context. In current
code, the receive buffer context stays 1:1 with the io and won't be
reposted to the hardware until the io completes. There is no need for such
a relationship.
Change the driver so that up on successful handing of the command to the
transport, where the transport has copied what it needed thus the buffer is
returned to the driver, have the driver immediately repost the buffer to
the hardware. If the command cannot be successfully handed to the transport
as transport resources are temporarily busy, have the driver allocate a new
and separate receive buffer and post it to the hardware so that hardware
can continue while the command is queued for the transport.
When an io is complete, the transport returns the io context to the driver,
and the driver may be waiting for more contexts, thus immediately reuse the
io context. In this path, there was a buffer posted when the receive buffer
was queued waiting for an io context so a replacement is not needed in the
new code additions. Thus, exempt this the context reuse case from the
buffer reposting.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The debug ktime counters that trace an io were inadvertently not placed in
the common section of an io buffer. Thus, they generate an invalid opcode
error when accessed.
Move the ktime counters into the common area.
Fixes: 0794d601d1 ("scsi: lpfc: Implement common IO buffers between NVME and SCSI")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.
Revise the code to stop sending these commands on a SLI4 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unloading the driver, mailbox commands may be sent without holding a
reference on the ndlp. By the time the mailbox command completes, the ndlp
may have reduced its ref counts and been freed. The problem was reported
by KASAN.
While unregistering due to driver unload, have the completion noop'd by
setting the ndlp context NULL'd. Due to the unload, no further action was
necessary. Also, while reviewing this path, the generic nulling of the
context after handling should be slightly moved.
Reported by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A patch in the 12.2.0.0 set caused a new lockdep warning:
WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
5.0.0-rc8-next-20190301-dbg+ #1 Not tainted
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&qp->io_buf_list_put_lock)->rlock);
local_irq_disable();
lock(&(&phba->hbalock)->rlock);
lock(&(&qp->io_buf_list_put_lock)->rlock);
<Interrupt>
lock(&(&phba->hbalock)->rlock);
see: https://www.spinics.net/lists/linux-scsi/msg128389.html
In summary, the new patch added taking the io_buf_list_put_lock while under
an irq-disabled hbalock. This created a lock heirarchy dependent upon irq
being disabled, and there are paths that take the io_buf_list_put_lock
without disabling irq.
Looking at the lpfc_io_free routine, which is where the new heirarchy was
introduced, there is no reason to be taking out the hbalock and raising
irq, as the functionality is replaced by the io_buf_list_xxx locks.
Resolve by removing the hbalock/irq calls in lpfc_io_free.
Fixes: 5e5b511d8b ("scsi: lpfc: Partition XRI buffer list across Hardware Queues")
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A prior patch which added support for non-uniform allocation of MSIX
vectors now causes a smatch complaint:
drivers/scsi/lpfc/lpfc_scsi.c:3674 lpfc_scsi_cmd_iocb_cmpl()
error: we previously assumed 'phba->sli4_hba.hdwq' could be
null (see line 3667)
Resolve by removing the unnecessary check for a NULL hdwq table.
Fixes 6a828b0f61: ("scsi: lpfc: Support non-uniform allocation of MSIX vectors to hardware queues")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the final round of mostly small fixes and performance
improvements to our initial submit. The main regression fix is the
ia64 simscsi build failure which was missed in the serial number
elimination conversion.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIxBayYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisherpAP4rxLpX
bcUnQnEsvoxys/JyoK08Qfv1JebZo1B2MAZ62wD/VZ7LpOuzVLhsM2KhLFGRrs1/
7D2K4tgtO2dQsFix7H0=
=pcHl
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the final round of mostly small fixes and performance
improvements to our initial submit.
The main regression fix is the ia64 simscsi build failure which was
missed in the serial number elimination conversion"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: ia64: simscsi: use request tag instead of serial_number
scsi: aacraid: Fix performance issue on logical drives
scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
scsi: hisi_sas: Set PHY linkrate when disconnected
scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
scsi: qla2xxx: check for kstrtol() failure
scsi: lpfc: fix 32-bit format string warning
scsi: lpfc: fix unused variable warning
scsi: target: tcmu: Switch to bitmap_zalloc()
scsi: libiscsi: fall back to sendmsg for slab pages
scsi: qla2xxx: avoid printf format warning
scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
scsi: ufs: hisi: fix ufs_hba_variant_ops passing
scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
...
It used to be that "error" was set to -ENODEV at the start of the function
but we shifted some code around an now "error" is set to zero for most
error paths. There is a mix of direct returns and "goto out" but I changed
everything to direct returns for consistency.
Fixes: 56de835704 ("scsi: lpfc: fix calls to dma_set_mask_and_coherent()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
On 32-bit architectures, we see a warning when %ld is used to print a
size_t:
In file included from drivers/scsi/lpfc/lpfc_init.c:62:
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_new_io_buf':
drivers/scsi/lpfc/lpfc_logmsg.h:62:45: error: format '%ld' expects argument of type 'long int', but argument 5 has type 'unsigned int' [-Werror=format=]
This is harmless, but portable code should just use %zd to avoid the
warning.
Fixes: 0794d601d1 ("scsi: lpfc: Implement common IO buffers between NVME and SCSI")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The newly introduced 'cpu' variable is only used inside of an optional
block, so we get a warning without CONFIG_SCSI_LPFC_DEBUG_FS:
drivers/scsi/lpfc/lpfc_nvme.c: In function 'lpfc_nvme_io_cmd_wqe_cmpl':
drivers/scsi/lpfc/lpfc_nvme.c:968:30: error: unused variable 'cpu' [-Werror=unused-variable]
uint32_t code, status, idx, cpu;
Move the declaration into the same block to avoid the warning.
Fixes: 63df6d637e ("scsi: lpfc: Adapt cpucheck debugfs logic to Hardware Queues")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The patch that replaced io channels for hdw_queues now reports the
following static checker warning:
drivers/scsi/lpfc/lpfc_init.c:11136 lpfc_sli4_hba_unset()
error: we previously assumed 'phba->pport' could be null (see line 11074)
Resolve by adding a pport NULL check.
[mkp: tag tweak]
Fixes: cdb42becdd ("scsi: lpfc: Replace io_channels for nvme and fcp with general hdw_queues per cpu"_
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The outer routine lpfc_sli_issue_iocb(), which decomposes into the
SLI3 (s3) or SLI4 (s4) subroutines takes out the locks. For s3, it takes
out the hbalock. For s4, it takes out the ring_lock. The lockdep check in
the s3 and s4 subroutines both check hbalock, which is incorrect for s4.
Revise the s4 subroutine to lockdep check the ring_lock.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nine small fixes. The resume fix is a cosmetic removal of a warning
with an incorrect condition causing it to alarm people wrongly. The
other eight patches correct a thinko in Christoph Hellwig's DMA
conversion series. Without it all these drivers end up with 32 bit
DMA masks meaning they bounce any page over 4GB before sending it to
the controller. Nowadays, even laptops mostly have memory above 4GB,
so this can lead to significant performance degradation with all the
bouncing.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXHql8CYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQmvAQCSVQRf
kx3ABDGnaj4Km4/Jzibj44aCYwh+ewwtLCWwFQD9GWaEaDxBkbxQDf/YndQKRhYg
VJQjjj6a9VlNSmWoW28=
=L9Fe
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine small fixes.
The resume fix is a cosmetic removal of a warning with an incorrect
condition causing it to alarm people wrongly.
The other eight patches correct a thinko in Christoph Hellwig's DMA
conversion series. Without it all these drivers end up with 32 bit DMA
masks meaning they bounce any page over 4GB before sending it to the
controller.
Nowadays, even laptops mostly have memory above 4GB, so this can lead
to significant performance degradation with all the bouncing"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Avoid that system resume triggers a kernel warning
scsi: hptiop: fix calls to dma_set_mask()
scsi: hisi_sas: fix calls to dma_set_mask_and_coherent()
scsi: csiostor: fix calls to dma_set_mask_and_coherent()
scsi: bfa: fix calls to dma_set_mask_and_coherent()
scsi: aic94xx: fix calls to dma_set_mask_and_coherent()
scsi: 3w-sas: fix calls to dma_set_mask_and_coherent()
scsi: 3w-9xxx: fix calls to dma_set_mask_and_coherent()
scsi: lpfc: fix calls to dma_set_mask_and_coherent()
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded. This resulted in NVMe/FC connections failing due to
corrupted data buffers, and various other SCSI/FCP I/O errors.
Fixes: f30e1bfd61 ("scsi: lpfc: use dma_set_mask_and_coherent")
Cc: <stable@vger.kernel.org>
Suggested-by: Don Dutile <ddutile@redhat.com>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_cpu_affinity_check':
drivers/scsi/lpfc/lpfc_init.c:10599:19: warning:
variable 'phys_id' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit 6a828b0f61 ("scsi: lpfc:
Support non-uniform allocation of MSIX vectors to hardware queues")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a handful of statements that are indented incorrectly. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This should return -ENOMEM if kcalloc() fails, but it accidentally
returns success instead.
Fixes: 6a828b0f61 ("scsi: lpfc: Support non-uniform allocation of MSIX vectors to hardware queues")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For files modified as part of 12.2.0.0 patches, update copyright to 2019
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Various null pointer dereference and general protection fault panics occur
when there is a link bounce under load. There are a large number of "error"
message 6413 indicating "bad release".
The issues resolve to list corruptions due to missing or inconsistent lock
protection. Lockups are due to nested locks in the unsolicited abort
path. The unsolicited abort path calls the wrong abort processing
routine. There was also duplicate context release while aborts were still
active in the hardware.
Removed duplicate locks and added lock protection around list item
removal. Commonized lock handling around the abort processing routines.
Prevent context release while still in ABTS list.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the transport calls into the lpfc target to release an IO job
structure, which corresponds to an exchange, and if the driver was waiting
for an exchange in order to post a previously received command to the
transport, the driver immediately takes the IO job and reuses the context
for the prior command and calls nvmet_fc_rcv_fcp_req() to tell the
transport about a newly received command.
Problem is, the execution of the IO job release may be in the context of
the back end driver and its bio completion handlers, thus it may be in a
irq context and protection code kicks in in the bio and request layers that
are subsequently called.
Rework lpfc so that instead of immediately upcalling, queue it to a
deferred work thread and have the thread make the upcall.
Took advantage of this change to remove duplicated code with the normal
command receive path that preps the IO job and upcalls nvmet_fc. Created a
common routine both paths use.
Also corrected some errors that were found during review of the context
freeing and reuse - basically unlocked operations and a somewhat disjoint
set of calls to release associated job elements. Cleaned up this path and
added locks for coherency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The conversion to enable SCSI and NVME fc4 support ran into an issue with
NPIV support. With NVME, NPIV is not currently supported, but with SCSI it
was. The driver reverted to its lowest setting meaning NPIV with SCSI was
not allowed.
Convert the NPIV checks and implementation so that SCSI can continue to
allow NPIV support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A scsi host lock is taken on every io completion to check whether the abort
handler is waiting on the io completion. This is an expensive lock to take
on all completion when rarely in an abort condition.
Replace scsi host lock with command-specific lock. Synchronize completion
and abort paths by new cmd lock. Ensure all flag changing and nulling of
context pointers taken under lock. When adding lock to task management
abort, realized it was missing other synchronization locks. Added that
synchronization to match normal paths.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that performance mods don't split resources by protocol and enable both
protocols by default, there's no reason not to enable concurrent SCSI and
NVME fc4 support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The work done to date utilized the number of present cpus when sizing
per-cpu structures. Structures should have been sized based on the max
possible cpu count.
Convert the driver over to possible cpu count for sizing allocation.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current driver uses the older IRQ API for MSIX allocation
Change driver to utilize pci_alloc_irq_vectors when allocating IRQ vectors.
Make lpfc_cpu_affinity_check use pci_irq_get_affinity to determine how the
kernel mapped all the IRQs.
Remove msix_entries from SLI4 structure, replaced with pci_irq_vector()
usage.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driving high iop counts, auto_imax coalescing kicks in and drives the
performance to extremely small iops levels.
There are two issues:
1) auto_imax is enabled by default. The auto algorithm, when iops gets
high, divides the iops by the hdwq count and uses that value to
calculate EQ_Delay. The EQ_Delay is set uniformly on all EQs whether
they have load or not. The EQ_delay is only manipulated every 5s (a
long time). Thus there were large 5s swings of no interrupt delay
followed by large/maximum delay, before repeating.
2) When processing a CQ, the driver got mixed up on the rate of when
to ring the doorbell to keep the chip appraised of the eqe or cqe
consumption as well as how how long to sit in the thread and
process queue entries. Currently, the driver capped its work at
64 entries (very small) and exited/rearmed the CQ. Thus, on heavy
loads, additional overheads were taken to exit and re-enter the
interrupt handler. Worse, if in the large/maximum coalescing
windows,k it could be a while before getting back to servicing.
The issues are corrected by the following:
- A change in defaults. Auto_imax is turned OFF and fcp_imax is set
to 0. Thus all interrupts are immediate.
- Cleanup of field names and their meanings. Existing names were
non-intuitive or used for duplicate things.
- Added max_proc_limit field, to control the length of time the
handlers would service completions.
- Reworked EQ handling:
Added common routine that walks eq, applying notify interval and max
processing limits. Use queue_claimed to claim ownership of the queue
while processing. Always rearm the queue whenever the common routine
is called.
Rework queue element processing, namely to eliminate hba_index vs
host_index. Only one index is necessary. The queue entry can be
marked invalid and the host_index updated immediately after eqe
processing.
After rework, xx_release routines are now DB write functions. Renamed
the routines as such.
Moved lpfc_sli4_eq_flush(), which does similar action, to same area.
Replaced the 2 individual loops that walk an eq with a call to the
common routine.
Slightly revised lpfc_sli4_hba_handle_eqe() calling syntax.
Added per-cpu counters to detect interrupt rates and scale
interrupt coalescing values.
- Reworked CQ handling:
Added common routine that walks cq, applying notify interval and max
processing limits. Use queue_claimed to claim ownership of the queue
while processing. Always rearm the queue whenever the common routine
is called.
Rework queue element processing, namely to eliminate hba_index vs
host_index. Only one index is necessary. The queue entry can be
marked invalid and the host_index updated immediately after cqe
processing.
After rework, xx_release routines are now DB write functions. Renamed
the routines as such.
Replaced the 3 individual loops that walk a cq with a call to the
common routine.
Redefined lpfc_sli4_sp_handle_mcqe() to commong handler definition with
queue reference. Add increment for mbox completion to handler.
- Added a new module/sysfs attribute: lpfc_cq_max_proc_limit To allow
dynamic changing of the CQ max_proc_limit value being used.
Although this leaves an EQ as an immediate interrupt, that interrupt will
only occur if a CQ bound to it is in an armed state and has cqe's to
process. By staying in the cq processing routine longer, high loads will
avoid generating more interrupts as they will only rearm as the processing
thread exits. The immediately interrupt is also beneficial to idle or
lower-processing CQ's as they get serviced immediately without being
penalized by sharing an EQ with a more loaded CQ.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Review of the eq coalescing logic showed the code was a bit fragmented.
Sometimes it would save/set via an interrupt max value, while in others it
would do so via a usdelay. There were also two places changing eq delay,
one place that issued mailbox commands, and another that changed via
register writes if supported.
Clean this up by:
- Standardizing the operation of lpfc_modify_hba_eq_delay() routine so
that it is always told of a us delay to impose. The routine then chooses
the best way to set that - via register or via mbx.
- Rather than two value types stored in eq->q_mode (usdelay if change via
register, imax if change via mbox) - q_mode always contains usdelay.
Before any value change, old vs new value is compared and only if
different is a change done.
- Revised the dmult calculation. dmult is not set based on overall imax
divided by hardware queues - instead imax applies to a single cpu and
the value will be replicated to all cpus.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
So far MSIX vector allocation assumed it would be 1:1 with hardware
queues. However, there are several reasons why fewer MSIX vectors may be
allocated than hardware queues such as the platform being out of vectors or
adapter limits being less than cpu count.
This patch reworks the MSIX/EQ relationships with the per-cpu hardware
queues so they can function independently. MSIX vectors will be equitably
split been cpu sockets/cores and then the per-cpu hardware queues will be
mapped to the vectors most efficient for them.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The desired affinity for the hardware queue behavior is for hdwq 0 to be
affinitized with cpu 0, hdwq 1 to cpu 1, and so on. The implementation so
far does not do this if the number of cpus is greater than the number of
hardware queues (e.g. hardware queue allocation was administratively
reduced or hardware queue resources could not scale to the cpu count).
Correct the queue affinitization logic when queue count is less than
cpu count.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Default behavior is to use the information from the upper IO stacks to
select the hardware queue to use for IO submission. Which typically has
good cpu affinity.
However, the driver, when used on some variants of the upstream kernel, has
found queuing information to be suboptimal for FCP or IO completion locked
on particular cpus.
For command submission situations, the lpfc_fcp_io_sched module parameter
can be set to specify a hardware queue selection policy that overrides the
os stack information.
For IO completion situations, rather than queing cq processing based on the
cpu servicing the interrupting event, schedule the cq processing on the cpu
associated with the hardware queue's cq.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The XRI get/put lists were partitioned per hardware queue. However, the
adapter rarely had sufficient resources to give a large number of resources
per queue. As such, it became common for a cpu to encounter a lack of XRI
resource and request the upper io stack to retry after returning a BUSY
condition. This occurred even though other cpus were idle and not using
their resources.
Create as efficient a scheme as possible to move resources to the cpus that
need them. Each cpu maintains a small private pool which it allocates from
for io. There is a watermark that the cpu attempts to keep in the private
pool. The private pool, when empty, pulls from a global pool from the
cpu. When the cpu's global pool is empty it will pull from other cpu's
global pool. As there many cpu global pools (1 per cpu or hardware queue
count) and as each cpu selects what cpu to pull from at different rates and
at different times, it creates a radomizing effect that minimizes the
number of cpu's that will contend with each other when the steal XRI's from
another cpu's global pool.
On io completion, a cpu will push the XRI back on to its private pool. A
watermark level is maintained for the private pool such that when it is
exceeded it will move XRI's to the CPU global pool so that other cpu's may
allocate them.
On NVME, as heartbeat commands are critical to get placed on the wire, a
single expedite pool is maintained. When a heartbeat is to be sent, it will
allocate an XRI from the expedite pool rather than the normal cpu
private/global pools. On any io completion, if a reduction in the expedite
pools is seen, it will be replenished before the XRI is placed on the cpu
private pool.
Statistics are added to aid understanding the XRI levels on each cpu and
their behaviors.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that the lower half has much better per-cpu parallelization using the
hardware queues, the SCSI MQ support needs to be tied into it.
The involves the following mods:
- Use the hardware queue info from the midlayer to help select the
hardware queue to utilize. This required change to the get_scsi-buf_xxx
routines.
- Remove lpfc_sli4_scmd_to_wqidx_distr() routine. No longer needed.
- Includes fix for SLI-3 that does not have multi queue parallelization.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SLI4 nvme functions are passing the SLI3 ring number when posting wqe to
hardware. This should be indicating the hardware queue to use, not the ring
number.
Replace ring number with the hardware queue that should be used.
Note: SCSI avoided this issue as it utilized an older lfpc_issue_iocb
routine that properly adapts.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many io statistics were being sampled and saved using adapter-based data
structures. This was creating a lot of contention and cache thrashing in
the I/O path.
Move the statistics to the hardware queue data structures. Given the
per-queue data structures, use of atomic types is lessened.
Add new sysfs and debugfs stat routines to collate the per hardware queue
values and report at an adapter level.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Similar to the io execution path that reports cpu context information, the
debugfs routines for cpu information needs to be aligned with new hardware
queue implementation.
Convert debugfs cnd nvme cpucheck statistics to report information per
Hardware Queue.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Both NVME and SCSI aborts are now processed off the CQ workqueue and do not
generate events for the slowpath any more.
Remove the unused event code.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Once the IO buff allocations were made shared, there was a single XRI
buffer list shared by all hardware queues. A single list isn't great for
performance when shared across the per-cpu hardware queues.
Create a separate XRI IO buffer get/put list for each Hardware Queue. As
SGLs and associated IO buffers get allocated/posted to the firmware; round
robin their assignment across all available hardware Queues so that there
is an equitable assignment.
Modify SCSI and NVME IO submit code paths to use the Hardware Queue logic
for XRI allocation.
Add a debugfs interface to display hardware queue statistics
Added new empty_io_bufs counter to track if a cpu runs out of XRIs.
Replace common_ variables/names with io_ to make meanings clearer.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, both nvme and fcp each have their own concept of an io_channel,
which is a combination wq/cq and associated msix. Different cpus would
share an io_channel.
The driver is now moving to per-cpu wq/cq pairs and msix vectors. The
driver will still use separate wq/cq pairs per protocol on each cpu, but
the protocols will share the msix vector.
Given the elimination of the nvme and fcp io channels, the module
parameters will be removed. A new parameter, lpfc_hdw_queue is added which
allows the wq/cq pair allocation per cpu to be overridden and allocated to
lesser value. If lpfc_hdw_queue is zero, the number of pairs allocated will
be based on the number of cpus. If non-zero, the parameter specifies the
number of queues to allocate. At this time, the maximum non-zero value is
64.
To manage this new paradigm, a new hardware queue structure is created to
track queue activity and relationships.
As MSIX vector allocation must be known before setting up the
relationships, msix allocation now occurs before queue datastructures are
allocated. If the number of vectors allocated is less than the desired
hardware queues, the hardware queue counts will be reduced to the number of
vectors
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a extra queue and msix vector for expresslane. Now that the driver
will be doing queues per cpu, this oddball queue is no longer needed.
Expresslane will utilize the normal per-cpu queues.
Updated debugfs sli4 queue output to go along with the change
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, both NVME and SCSI get their IO buffers from separate
pools. XRI's are associated 1:1 with IO buffers, so XRI's are also split
between protocols.
Eliminate the independent pools and use a single pool. Each buffer
structure now has a common section and a protocol section. Per protocol
routines for SGL initialization are removed and replaced by common
routines. Initialization of the buffers is only done on the common area.
All other fields, which are protocol specific, are initialized when the
buffer is allocated for use in the per-protocol allocation routine.
In the past, the SCSI side allocated IO buffers as part of slave_alloc
calls until the maximum XRIs for SCSI was reached. As all XRIs are now
common and may be used for either protocol, allocation for everything is
done as part of adapter initialization and the scsi side has no action in
slave alloc.
As XRI's are no longer split, the lpfc_xri_split module parameter is
removed.
Adapters based on SLI3 will continue to use the older scsi_buf_list_get/put
routines. All SLI4 adapters utilize the new IO buffer scheme
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_nvme_prep_io_cmd() checks for null pnode, but caller
lpfc_nvme_fcp_io_submit() has already ensured it's non-null.
Remove the pnode null check.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An hba-wide lock is taken in the nvme io completion routine. The lock
covers null'ing of the nrport pointer in the cmd structure.
The nrport member isn't necessary. After extracting the pointer from the
command, the pointer was dereferenced to get the fc discovery node
pointer. But the fc discovery node pointer is alrady in the command
structure so the dereferrence was unnecessary.
Eliminated the nrport structure member and its use, which also eliminates
the port-wide lock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling debugfs functions, there is no need to ever check the return
value. The function can work or not, but the code logic should never do
something different based on this.
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Six fixes, all of which appear to have user visible consequences. The
DMA one is a regression fix from the merge window and of the others,
four are driver specific and one specific to the target code.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXEt6GSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbxoAP0R0z0J
fdCRn9AMRbZ3xJzD+E6V2gw38Gdgm8rR5mT1gQEAv1VxZwOAb9Qxbcr+l4uybqZr
Q55H31I/IvBgNm84jH0=
=vkW7
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fixes, all of which appear to have user visible consequences.
The DMA one is a regression fix from the merge window and of the
others, four are driver specific and one specific to the target code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: Use explicit access size in ufshcd_dump_regs
scsi: tcmu: fix use after free
scsi: csiostor: fix NULL pointer dereference in csio_vport_set_state()
scsi: lpfc: nvmet: avoid hang / use-after-free when destroying targetport
scsi: lpfc: nvme: avoid hang / use-after-free when destroying localport
scsi: communicate max segment size to the DMA mapping code
We cannot wait on a completion object in the lpfc_nvme_targetport structure
in the _destroy_targetport() code path because the NVMe/fc transport will
free that structure immediately after the .targetport_delete() callback.
This results in a use-after-free, and a hang if slub_debug=FZPU is enabled.
Fix this by putting the completion on the stack.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We cannot wait on a completion object in the lpfc_nvme_lport structure in
the _destroy_localport() code path because the NVMe/fc transport will free
that structure immediately after the .localport_delete() callback. This
results in a use-after-free, and a hang if slub_debug=FZPU is enabled.
Fix this by putting the completion on the stack.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A set of 17 fixes. Most of these are minor or trivial. The one fix
that may be serious is the isci one: the bug can cause hba parameters
to be set from uninitialized memory. I don't think it's exploitable,
but you never know.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXEKL0SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVZpAQCwuPTk
fqOt4v4hJ0oUHtEBsQK3VMXSdUvWdb5Lbn3WeQD/RFYTyNxcIF7ADSWw71b+IigT
ejUrMzI8ig+nZ1jbFZ4=
=BdS/
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of 17 fixes. Most of these are minor or trivial.
The one fix that may be serious is the isci one: the bug can cause hba
parameters to be set from uninitialized memory. I don't think it's
exploitable, but you never know"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: add wait_for_completion()
scsi: qla1280: set 64bit coherent mask
scsi: ufs: Fix geometry descriptor size
scsi: megaraid_sas: Retry reads of outbound_intr_status reg
scsi: qedi: Add ep_state for login completion on un-reachable targets
scsi: ufs: Fix system suspend status
scsi: qla2xxx: Use correct number of vectors for online CPUs
scsi: hisi_sas: Set protection parameters prior to adding SCSI host
scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes
scsi: isci: initialize shost fully before calling scsi_add_host()
scsi: lpfc: lpfc_sli: Mark expected switch fall-throughs
scsi: smartpqi_init: fix boolean expression in pqi_device_remove_start
scsi: core: Synchronize request queue PM status only on successful resume
scsi: pm80xx: reduce indentation
scsi: qla4xxx: check return code of qla4xxx_copy_from_fwddb_param
scsi: megaraid_sas: correct an info message
scsi: target/iscsi: fix error msg typo when create lio_qr_cache failed
scsi: sd: Fix cache_type_store()
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "Drop thru" and "Fall
Thru" with "fall through" annotations, which is what GCC is expecting to
find.
Also, in some cases a dash is added as a token in order to separate the
"fall through" annotation from the rest of the comment on the same line,
which is what GCC is expecting to find.
Addresses-Coverity-ID: 114979 ("Missing break in switch")
Addresses-Coverity-ID: 114980 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have
a pile of annotation, unused variable and minor updates. The big API
change is the updates for Christoph's DMA rework which include
removing the DISABLE_CLUSTERING flag. And finally there are a couple
of target tree updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
u1j3H7tha9j1it+4pUw=
=GDa+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
Update lpfc version to 12.0.0.10
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds a "pci_bus_reset" option to the board_mode sysfs attribute.
This option uses the pci_reset_bus() api to reset the PCIe link the adapter
is on, which will reset the chip/adapter. Prior to issuing this option,
all functions on the same chip must be placed in the offline state by the
admin. After the reset, all of the instances may be brought online again.
The primary purpose of this functionality is to support cases where
firmware update required a chip reset but the admin did not want to reboot
the machine in order to instantiate the firmware update.
Sanity checks take place prior to the reset to ensure the adapter is the
sole entity on the PCIe bus and that all functions are in the offline
state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current messages report generic actions (like send GID_FT), but misses
reporting for what protocol type the action is taken.
Revise the messages to reflect the FC4 protocol type being worked on.
[mkp: typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a target's link dropped, an RSCN was received to communicate the
change. The driver detected the loss of the target and issued and UNREG_RPI
mailbox command. While that was being processed, another RSCN was received
to communicate the port coming back. The driver deferred the PLOGI to the
port until the mailbox command finishes. When the mailbox command completed
it saw the pending port and called the routines to issue the
PLOGI. However, it forgot to clear the UNREG_INP state flag, so the PLOGI
xmt routine nooped the PLOGI request assuming it needed to wait for the
mailbox command. At this point, login would never be re-attempted.
Clear UNREG_INP before issuing the deferred PLOGI.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, when a trunk link goes down due to some fault, the driver
snapshots the fault code. If the link then comes back up, meaning there is
no fault, the driver is not clearing the fault code so the sysfs link_state
entry reports old/stale data.
Revise the logic so that on successful link up the fault code is cleared.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The existing MDS loopback diagnostics support processing received frames in
the slowpath work thread. It caps the number of frames it will process at
64, before waiting for another event to indicate additional frame
reception. The net-net is this results in very slow frame processing during
loopback tests and sometimes orphans an io, causing the loopback test to
report failure by the switch.
Move MDS loopback frame processing out of the slow path worker thread and
into the normal RQ processing routines.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter is taken offline, the trunk link port attributes continue to
report trunk links as up even though all links are down as the adapter is
offline.
Clear the trunk links state as part of taking the adapter offline.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Certain older adapters such as the OneConnect OCe10100 may not have a valid
wqpcnt value. In this case, do not set queue->page_count to 0 in
lpfc_sli4_queue_alloc() as this will prevent the driver from initializing.
Fixes: 895427bd01 ("scsi: lpfc: NVME Initiator: Base modifications")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addition of support for if_type=6 missed several checks for interface type,
resulting in the failure of several key management features such as
firmware dump and loopback testing.
Correct the checks on the if_type so that both SLI4 IF_TYPE's 2 and 6 are
supported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 287aba2592.
We killed the bad firmware and this mod is no longer necessary.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwNpb0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGwGwH/00UHnXfxww3ixxz
zwTVDzptA6SPm6s84yJOWatM5fXhPiAltZaHSYF9lzRzNU71NCq7Frhq3fQUIXKM
OxqDn9nfSTWcjWTk2q5n2keyRV/KIn67YX7UgqFc1bO/mqtVjEgNWaMyblhI+e9E
giu1ZXayHr43jK1cDOmGExZubXUq7Vsc9TOlrd+d2SwIqeEP7TCMrPhnHDwCNvX2
UU5dtANpVzGtHaBcr37wJj+L8kODCc0f+PQ3g2ar5jTHst5SLlHp2u0AMRnUmgdi
VkGx+mu/uk8mtwUqMIMqhplklVoqK6LTeLqsY5Xt32SKruw9UqyJGdphLjW2QP/g
MkmA1lI=
=7kaD
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc6' into for-4.21/block
Pull in v4.20-rc6 to resolve the conflict in NVMe, but also to get the
two corruption fixes. We're going to be overhauling the direct dispatch
path, and we need to do that on top of the changes we made for that
in mainline.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Update the driver version to 12.0.0.9
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When dif and first burst is used in a write command wqe, the driver was not
properly setting fields in the io command request. This resulted in no dif
bytes being sent and invalid xfer_rdy's, resulting in the io being aborted
by the hardware.
Correct the wqe initializaton when both dif and first burst are used.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On driver termination, after the driver stops fw logging by writing a
register on the chip, the driver immediately unmaps and frees the logging
buffer, without confirming in any way that the chip has received the write
and terminated the logging. As termination on the chip is not immediate,
the chip may issue a dma request to the now unmapped dma buffer, resulting
in a iommu fault.
Change the driver to receive a confirmation that logging ahs been
terminated. As the driver always issues an SLI reset with the device as
part of shutdown, and as part of that is receiving confirmation that the
reset is complete - the driver was modified to perform the write to disable
fw logging prior to the SLI reset and only free the fw log buffer after the
SLI reset is complete. That guarantees use of the fw log buffer is fully
terminated when it is unmapped.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver missed classifying the chip type for G7 when reporting supported
topologies. This resulted in loop being shown as supported on FC links that
are not supported per the standard.
Add the chip classifications to the topology checks in the driver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is setting bits in word 10 of the SLI4 ABORT WQE (the wqid). The
field was a carry over from a prior SLI revision. The field does not exist
in SLI4, and the action may result in an overlap with future definition of
the WQE.
Remove the setting of WQID in the ABORT WQE.
Also cleaned up WQE field settings - initialize to zero, don't bother to
set fields to zero.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current discovery state machine the driver treated FLOGI oddly. When
point to point, an FLOGI is to be exchanged by the two ports, with the port
with the most significant WWN then proceeding with PLOGI. The
implementation in the driver was keyed to closely with "what have I sent",
not with what has happened between the two endpoints. Thus, it blatantly
would ACC an FLOGI, but reject PLOGI's until it had its FLOGI ACC'd. The
problem is - the sending of FLOGI may be delayed for some reason, or the
response to FLOGI held off by the other side. In the failing situation the
other side sent an FLOGI, which was ACC'd, then sent PLOGIs which were then
rjt'd until the retry count for the PLOGIs were exceeded and the port gave
up. The FLOGI may have been very late in transmit, or the response held off
until the PLOGIs failed. Given the other port had the higher WWN, no PLOGIs
would occur and communication stopped.
Correct the situation by changing the FLOGI handling. Defer any response to
an FLOGI until the driver has sent its FLOGI as well. Then, upon either
completion of the sent FLOGI, or upon sending an ACC to a received FLOGI
(which may be received before or just after FLOGI was sent). the driver
will act on who has the higher WWN. if the other port does, the driver will
noop any handling of an FLOGI response (if outstanding) and wait for PLOGI.
If the local port does, the driver will transition to sending PLOGI and
will noop any action on responding to an FLOGI (if not yet received).
Fortunately, to implement this, it only took another state flag and
deferring any FLOGI response if the FLOGI has yet to be transmit. All
subsequent actions were already in place.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In some link initialization sequences, the fw generates an erroneous FLOGI
payload to the driver without an intervening link bounce. The driver, when
it sees a 2nd FLOGI without an intervening link bounce, automatically
performs a link bounce. In this, the link bounce causes the situate to
repeat and in a nasty loop of link bounces.
Resolve the issue by validating the FLOGI payload. The erroneous FLOGI will
contain VVL signatures that are not normal. When the driver sees these, it
will simply reject the flogi rather than bouncing the link. The reject is
consumed within the firmware.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Two initiator ports were cable swapped and after swap both went down. The
driver internally swaps the nlp nodes based on matching node wwn's but not
the same nport id as before. After detecting a change in the nodes RPI, the
driver sends an UNREG_RPI command and clears the NLP_RPI_REGISTERED flag,
then swaps the node information with the other node. But the other node's
NLP_RPI_REGISTERED flag is also cleared, but it is done so without an
UNREG_RPI being sent, which causes the later REG_RPI for that other node to
fail as the hardware believes its still registered.
Additionally, if the node swap occurred while the two nodes had PLOGI's in
flight, the fc4_types weren't properly getting swapped such that when the
PLOGIs commpleted and PRLI's were then sent, the PRLI's acted on bad
protocol types so the PRLI was for the wrong protocol. NVME devices saw
SCSI FCP PRLIs and vice versa.
Clean up the node swap so that the NLP_RPI_REGISTERED flag is handled
properly.
Fix the handling of the fc4_types when the nodes are swapped as well
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Depending on the chipset, the number of NPIV vports may vary and be in
excess of what most switches support (256). To avoid confusion with the
users, limit the reported NPIV vports to 256.
Additionally correct the 16G adapter which is reporting a bogus NPIV vport
number if the link is down.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is hitting null pring pointers in lpfc_do_work().
Pointer assignment occurs based on SLI-revision. If recovering after an
error, its possible the sli revision for the port was cleared, making the
lpfc_phba_elsring() not return a ring pointer, thus the null pointer.
Add SLI revision checking to lpfc_phba_elsring() and status checking to all
callers.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Renumber one of the 0711 log messages so there isn't a duplication.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is getting hit with 100s of RSCNs during remote port address
changes. Each of those RSCN's ends up generating UNREG_RPI and REG_PRI
mailbox commands. The discovery engine within the driver doesn't wait for
the mailbox command completions. Instead it sets state flags and moves
forward. At some point, there's a massive backlog of mailbox commands which
take time for the adapter to process. Additionally, it appears there were
duplicate events from the switch so the driver generated duplicate mailbox
commands for the same remote port. During this window, failures on PLOGI
and PRLI ELS's are see as the adapter is rejecting them as they are for
remote ports that still have pending mailbox commands.
Streamline the discovery engine so that PLOGI log checks for outstanding
UNREG_RPIs and defer the processing until the commands complete. This
better synchronizes the ELS transmission vs the RPI registrations.
Filter out multiple UNREG_RPIs being queued up for the same remote port.
Beef up log messages in this area.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver data structure for managing a mailbox command contained two
context fields. Unfortunately, the context were considered "generic" to be
used at the whim of the command code. Of course, one section of code used
fields this way, while another did it that way, and eventually there were
mixups.
Refactored the structure so that the generic contexts become a node context
and a buffer context and all code standardizes on their use.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update manufacturer attribute to reflect Broadcom Inc, not Emulex
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While trying to get adapter fw-log for a function whose buffsize was set to
0, kernel panic occurred.
When buffsize is 0, the kernel buffer for the log won't be allocated. When
fw log usage was enabled, it failed to check the buffer size, and log usage
was started. Eventually the driver referenced the unallocated log buffer.
Added checks of the buffer size before allowing fw logging to be enabled
and added check for valid buffer if enabling fw log.
Performed a couple other minor cleanups while fixing this:
- clarified log messages
- re-evaluated log message severity
- treat any error as an error, not only a couple codes
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since f44ac12f1d, BG enablement is tracked with the LPFC_SLI3_BG_ENABLED
bit, which is set in lpfc_get_cfgparam before lpfc_sli_config_sli_port() is
called. The bit shouldn't be cleared before checking the feature. Based on
problem analysis by David Bond.
Fixes: f44ac12f1d "scsi: lpfc: Memory allocation error during driver start-up on power8"
Tested-by: David Bond <dbond@suse.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Cc: stable@vger.kernel.org # 4.17.x
Cc: stable@vger.kernel.org # 4.18.x
Cc: stable@vger.kernel.org # 4.19.x
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replaced dma_alloc_coherent + memset with dma_zalloc_coherent.
Signed-off-by: Sabyasachi Gupta <sabyasachi.linux@gmail.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlvx2sAeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGycgIAIuxobwt0RRKa0zO
ROS+34JGoC2yU2P9VdEGWdtxS6ANMVQgKPBhWL6s+xR89Kd+V4xSdJLD1pNTxxqP
0DCva0np1/Q4juH+JbU50v/lykoLgteZ0P0LBRGf1y8p3WiLPv45IbnNsMDNYhB2
7a8rOmZYakRY9CPznRDw3X8cJt3sddKgFJHIOGz1OQJVWtCD0KPGcJmQNsbDSagY
Zx6Z5BKSIdjRqaAdN5gDa1Pft3WQo7TpaQGl80lSsgr5LcjmscXA3sClOCy+25Mo
FZLx0PcwP+Efq8RTGzNK51WSOMa6d37hvjDqUAdQBOR0KbyjRyXQwyQVw/MGbPJs
7J3Pzm0=
=56Mt
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc3' into for-4.21/block
Merge in -rc3 to resolve a few conflicts, but also to get a few
important fixes that have gone into mainline since the block
4.21 branch was forked off (most notably the SCSI queue issue,
which is both a conflict AND needed fix).
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API. Switch it over to the better generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This removes the legacy (non-mq) IO path for SCSI.
Cc: linux-scsi@vger.kernel.org
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Update the driver version to 12.0.0.8
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add trunking support to the driver. Trunking is found on more recent
asics. In general, trunking appears as a single "port" to the driver
and overall behavior doesn't differ. Link speed is reported as an
aggregate value, while link speed control is done on a per-physical
link basis with all links in the trunk symmetrical. Some commands
returning port information are updated to additionally provide
trunking information. And new ACQEs are generated to report physical
link events relative to the trunk.
This patch contains the following modifications:
- Added link speed settings of 128GB and 256GB.
- Added handling of trunk-related ACQEs, mainly logging and trapping
of physical link statuses.
- Added additional bsg interface to query trunk state by applications.
- Augment link_state sysfs attribtute to display trunk link status
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The switches seem to respond faster to GID_PT vs GID_FT NameServer
queries. Add support for GID_PT to be used over GID_FT to enable
faster storage failover detection. Includes addition of new module
parameter to select between GID_PT and GID_FT (GID_FT is default).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An address change for a remote port cause PRLI for the wrong protocol
to be sent. The node copy done in the discovery code skipped copying
the fc4 protocols supported as well.
Fix the copy logic for the address change. Beefed up log messages in
this area as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Testing a point-to-point topology and a case of re-FLOGI without
intervening link bouncing, showed an odd interaction with firmware and
a resulting scenario where the driver no longer probed after accepting
the new FLOGI.
Work around the firmware issue by issuing a link bounce if a FLOGI is
received after the link is already up and FLOGI's accepted.
While debugging the issue, realized that some debug traces should be
clarified to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When LCB's are rejected, if beaconing was already in progress, the
Reason Code Explanation was not being set. Should have been set to
command in progress.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On FCoE adapters, when running link bounce test in a loop, initiator
failed to login with switch switch and required driver reload to
recover. Switch reached a point where all subsequent FLOGIs would be
LS_RJT'd. Further testing showed the condition to be related to not
performing FCF discovery between FLOGI's.
Fix by monitoring FLOGI failures and once a repeated error is seen
repeat FCF discovery.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch corrects two issues:
- An oops would occur if reading based on a non-zero offset. Offset
calculation was incorrect.
- Updates to ras config (logging level) were ignored if change was
made while fw logging was enabled. Revise to dynamically update.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, PLOGI failures are infinitely delayed/retried. There have
been some fabric situations where the PLOGI's were to the nameserver
and it stopped responding. The retries would never clear up. A better
resolution in this situation is to retry a couple of times, then drop
the link and reinit. This brings back connectivity to the nameserver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a LOGO in response to an ABTS timeout, a PLOGI wasn't issued to
re-establish the login. An nlp_type check in the LOGO completion
handler failed to restart discovery for NVME targets. Revised the
nlp_type check for NVME as well as SCSI.
While reviewing the LOGO handling a few other issues were seen and
were addressed:
- Better lock synchronization around ndlp data types
- When the ABTS times out, unregister the RPI before sending the LOGO
so that all local exchange contexts are cleared and nothing received
while awaiting LOGO/PLOGI handling will be accepted.
- LOGO handling optimized to:
Wait only R_A_TOV for a response.
It doesn't need to be retried on timeout. If there wasn't a
response, a PLOGI will be sent, thus an implicit logout
applies as well when the other port sees it.
If there is a response, any kind of response is considered "good"
and the XRI quarantined for a exchange qualifier window.
- PLOGI is issued as soon a LOGO state is resolved.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An error is an error - but not to the existing return value check.
Revise check to handle any failure, not just EIO.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Supported speeds is not updated when SFP is removed or replaced
Supported speed is obtained from lmt field in READ_CONFIG mailbox
response. Driver updates supported speeds only once from PCI probe
path. After that it is never updated. So, supported speeds remains the
same till reboot or driver reload.
When SFP is removed or inserted, driver gets SLI-Port Event ACQE. If
SFP is removed, lmt wil have value 0. If a different SFP is inserted,
lmt will have value according to its supported speeds. So, afterr
SLI-Port Event ACQE handling path, send READ_CONFIG mailbox and update
supported speeds. If READ_CONFIG fails, set supported speeds to
unknown and log.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The addition of a spinlock in lpfc_debugfs_nodelist_data() introduced
a bug that lets us not skip NULL pointers correctly, as noticed by
gcc-8:
drivers/scsi/lpfc/lpfc_debugfs.c: In function 'lpfc_debugfs_nodelist_data.constprop':
drivers/scsi/lpfc/lpfc_debugfs.c:728:13: error: 'nrport' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (nrport->port_role & FC_PORT_ROLE_NVME_INITIATOR)
This changes the logic back to what it was, while keeping the added
spinlock.
Fixes: 9e21017826 ("scsi: lpfc: Synchronize access to remoteport via rport")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual drivers: UFS, esp_scsi, NCR5380,
qla2xxx, lpfc, libsas, hisi_sas. In addition there's a set of mostly
small updates to the target subsystem a set of conversions to the
generic DMA API, which do have some potential for issues in the older
drivers but we'll handle those as case by case fixes. A new myrs for
the DAC960/mylex raid controllers to replace the block based DAC960
which is also being removed by Jens in this merge window. Plus the
usual slew of trivial changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW9BQJSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishU3MAP41T8yW
UJQDCprj65pCR+9mOUWzgMvgAW/15ouK89x/7AD/XAEQZqoAgpFUbgnoZWGddZkS
LykIzSiLHP4qeDOh1TQ=
=2JMU
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual drivers: UFS, esp_scsi, NCR5380,
qla2xxx, lpfc, libsas, hisi_sas.
In addition there's a set of mostly small updates to the target
subsystem a set of conversions to the generic DMA API, which do have
some potential for issues in the older drivers but we'll handle those
as case by case fixes.
A new myrs driver for the DAC960/mylex raid controllers to replace the
block based DAC960 which is also being removed by Jens in this merge
window.
Plus the usual slew of trivial changes"
[ "myrs" stands for "MYlex Raid Scsi". Obviously. Silly of me to even
wonder. There's also a "myrb" driver, where the 'b' stands for
'block'. Truly, somebody has got mad naming skillz. - Linus ]
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (237 commits)
scsi: myrs: Fix the processor absent message in processor_show()
scsi: myrs: Fix a logical vs bitwise bug
scsi: hisi_sas: Fix NULL pointer dereference
scsi: myrs: fix build failure on 32 bit
scsi: fnic: replace gross legacy tag hack with blk-mq hack
scsi: mesh: switch to generic DMA API
scsi: ips: switch to generic DMA API
scsi: smartpqi: fully convert to the generic DMA API
scsi: vmw_pscsi: switch to generic DMA API
scsi: snic: switch to generic DMA API
scsi: qla4xxx: fully convert to the generic DMA API
scsi: qla2xxx: fully convert to the generic DMA API
scsi: qla1280: switch to generic DMA API
scsi: qedi: fully convert to the generic DMA API
scsi: qedf: fully convert to the generic DMA API
scsi: pm8001: switch to generic DMA API
scsi: nsp32: switch to generic DMA API
scsi: mvsas: fully convert to the generic DMA API
scsi: mvumi: switch to generic DMA API
scsi: mpt3sas: switch to generic DMA API
...
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAlvPV7IUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vyaUg//WnCaRIu2oKOp8c/bplZJDW5eT10d
oYAN9qeyptU9RYrg4KBNbZL9UKGFTk3AoN5AUjrk8njxc/dY2ra/79esOvZyyYQy
qLXBvrXKg3yZnlNlnyBneGSnUVwv/kl2hZS+kmYby2YOa8AH/mhU0FIFvsnfRK2I
XvwABFm2ZYvXCqh3e5HXaHhOsR88NQ9In0AXVC7zHGqv1r/bMVn2YzPZHL/zzMrF
mS79tdBTH+shSvchH9zvfgIs+UEKvvjEJsG2liwMkcQaV41i5dZjSKTdJ3EaD/Y2
BreLxXRnRYGUkBqfcon16Yx+P6VCefDRLa+RhwYO3dxFF2N4ZpblbkIdBATwKLjL
npiGc6R8yFjTmZU0/7olMyMCm7igIBmDvWPcsKEE8R4PezwoQv6YKHBMwEaflIbl
Rv4IUqjJzmQPaA0KkRoAVgAKHxldaNqno/6G1FR2gwz+fr68p5WSYFlQ3axhvTjc
bBMJpB/fbp9WmpGJieTt6iMOI6V1pnCVjibM5ZON59WCFfytHGGpbYW05gtZEod4
d/3yRuU53JRSj3jQAQuF1B6qYhyxvv5YEtAQqIFeHaPZ67nL6agw09hE+TlXjWbE
rTQRShflQ+ydnzIfKicFgy6/53D5hq7iH2l7HwJVXbXRQ104T5DB/XHUUTr+UWQn
/Nkhov32/n6GjxQ=
=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_debugfs.c: In function 'lpfc_debugfs_nodelist_data':
drivers/scsi/lpfc/lpfc_debugfs.c:553:29: warning:
variable 'tgtp' set but not used [-Wunused-but-set-variable]
It never used since 2b65e18202 ("scsi: lpfc: NVME Target: Add debugfs support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_hbadisc.c: In function 'lpfc_free_tx':
drivers/scsi/lpfc/lpfc_hbadisc.c:5431:19: warning:
variable 'psli' set but not used [-Wunused-but-set-variable]
Since commit 895427bd01 ("scsi: lpfc: NVME Initiator: Base modifications")
'psli' is not used any more.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_sli.c: In function 'lpfc_sli4_sp_handle_rcqe':
drivers/scsi/lpfc/lpfc_sli.c:13430:26: warning:
variable 'fc_hdr' set but not used [-Wunused-but-set-variable]
drivers/scsi/lpfc/lpfc_sli.c: In function 'lpfc_cq_create':
drivers/scsi/lpfc/lpfc_sli.c:14852:11: warning:
variable 'hw_page_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in lpfc_printf_log message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
dma_alloc_coherent allocates memory that can be used by the cpu and the
device at the same time, calls to pci_dma_sync_* are not required, and in
fact actively harmful on some architectures like arm.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After bfcb79fca1 ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.
Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The driver currently uses the ndlp to get the local rport which is then used
to get the nvme transport remoteport pointer. There can be cases where a stale
remoteport pointer is obtained as synchronization isn't done through the
different dereferences.
Correct by using locks to synchronize the dereferences.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_nvme.c: In function 'lpfc_new_nvme_buf':
drivers/scsi/lpfc/lpfc_nvme.c:2238:24: warning:
variable 'sgl_size' set but not used [-Wunused-but-set-variable]
int bcnt, num_posted, sgl_size;
^
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 12.0.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the ability to read firmware logs from the adapter. The driver
registers a buffer with the adapter that is then written to by the adapter.
The adapter posts CQEs to indicate content updates in the buffer. While the
adapter is writing to the buffer in a circular fashion, an application will
poll the driver to read the next amount of log data from the buffer.
Driver log buffer size is configurable via the ras_fwlog_buffsize sysfs
attribute. Verbosity to be used by firmware when logging to host memory is
controlled through the ras_fwlog_level attribute. The ras_fwlog_func
attribute enables or disables loggy by firmware.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, on each io completion, the stats update routine indiscriminately
holds a lock. While holding the adapter-wide lock, checks are made to check
whether status are being tracked. When disabled (the default), the locking
wasted a lot of cycles.
Check for stats enablement before taking the lock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Message 6408 is displayed for each entry in an array, but the cpu and queue
numbers were incorrect for the entry. Message 6001 includes an extraneous
character.
Resolve both issues
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During attachment, the driver writes the EQ doorbell to disable potential
interrupts from an EQ. The current EQ doorbell format used for clearing the
interrupt is incorrect and uses an if_type=2 format, making the operation act
on the wrong EQ.
Correct the code to use the proper if_type=6 EQ doorbell format.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When taking the board offline while performing i/o, unsafe locking errors
occurred and irq level isn't properly managed.
In lpfc_sli_hba_down, spin_lock_irqsave(&phba->hbalock, flags) does not
disable softirqs raised from timer expiry. It is possible that a softirq is
raised from the lpfc_els_retry_delay routine and recursively requests the same
phba->hbalock spinlock causing deadlock.
Address the deadlocks by creating a new port_list lock. The softirq behavior
can then be managed a level deeper into the calling sequences.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When running an mds diagnostic that passes frames with the switch, soft
lockups are detected. The driver is in a CQE processing loop and has
sufficient amount of traffic that it never exits the ring processing routine,
thus the "lockup".
Cap the number of elements in the work processing routine to 64 elements. This
ensures that the cpu will be given up and the handler reschedule to process
additional items.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On io completion, the driver is taking an adapter wide lock and nulling the
scsi command back pointer. The nulling of the back pointer is to signify the
io was completed and the scsi_done() routine was called. However, the routine
makes no check to see if the abort routine had done the same thing and
possibly nulled the pointer. Thus it may doubly-complete the io.
Make the following mods:
- Check to make sure forward progress (call scsi_done()) only happens if the
command pointer was non-null.
- As the taking of the lock, which is adapter wide, is very costly on a system
under load, null the pointer using an xchg operation rather than under lock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When nvme is enabled, change the default for two parameters:
sg_seg_cnt - raise the per-io sg list size so that 1MB ios are
supported (based on a 4k buffer per element).
iocb_cnt - raise the number of buffers used for things like
NVME LS request/responses to allow more concurrent requests
to for larger nvme configs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver allocates a sg list per io struture based on a fixed maximum
size. When it registers with the protocol transports and indicates the max sg
list size it supports, the driver manipulates the fixed value to report a
lesser amount so that it has reserved space for sg elements that are used for
DIF.
The driver initialization path sets the cfg_sg_seg_cnt field to the
manipulated value for scsi. NVME initialization ran afterward and capped it's
maximum by the manipulated value for SCSI. This erroneously made NVME report
the SCSI-reduce-for-DIF value that reduced the max io size for nvme and wasted
sg elements.
Rework the driver so that cfg_sg_seg_cnt becomes the overall maximum size and
allow the max size to be tunable. A separate (new) scsi sg count is then
setup with the scsi-modified reduced value. NVME then initializes based off
the overall maximum.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver only sends NVME PRLI to a device that also supports FCP. This resuls
in remote ports that don't have fc_remote_ports created for them. The driver
is clearing the nlp_fc4_type for a ndlp at the wrong time.
Fix by moving the nlp_fc4_type clearing to the discovery engine in the
DEVICE_RECOVERY state. Also ensure that rport registration is done for all
nlp_fc4_types.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Smatch complains about this code:
drivers/scsi/lpfc/lpfc_scsi.c:1053 lpfc_get_scsi_buf_s4()
warn: variable dereferenced before check 'lpfc_cmd' (see line 1039)
Fortunately the NULL check isn't required so I have removed it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent change added some MDS processing in the lpfc_drain_txq routine
that relies on the fcp_wq being allocated. For nvmet operation the fcp_wq
is not allocated because it can only be an nvme-target. When the original
MDS support was added LS_MDS_LOOPBACK was defined wrong, (0x16) it should
have been 0x10 (decimal value used for hex setting). This incorrect value
allowed MDS_LOOPBACK to be set simultaneously with LS_NPIV_FAB_SUPPORTED,
causing the driver to crash when it accesses the non-existent fcp_wq.
Correct the bad value setting for LS_MDS_LOOPBACK.
Fixes: ae9e28f36a ("lpfc: Add MDS Diagnostic support.")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
