Currently the discovery layers within the driver use the SCSI midlayer
host_lock to access node-specific structures. This can contend with the I/O
path and is too coarse of a lock.
Rework the driver so that it uses a lock specific to the remote port node
structure when accessing the structure contents. A few of the changes
brought out spots were some slightly reorganized routines worked better.
Link: https://lore.kernel.org/r/20201115192646.12977-6-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that the driver has gone to a normal ref interface (with no odd logic)
the discovery logic needs to be updated to reworked so that it properly
takes references when it should and give them up when it should.
Rework the driver for the following get/put model:
- Move gets to just before an I/O is issued. Add gets for places where an
I/O was issued without one.
- Ensure that failures from lpfc_nlp_get() are handled by the driver.
- Check and fix the placement of lpfc_nlp_puts relative to io completions.
Note: some of these paths may not release the reference on the exact io
completion as the reference is held as the code takes another step in
the discovery thread and which may cause another io to be issued.
- Rearrange some code for error processing and calling lpfc_nlp_put.
- Fix some places of incorrect reference freeing that was causing the
premature releasing of the structure.
- Nvmet plogi handling performs unreg_rpi's. The reference counts were
unbalanced resulting in premature node removal. In some cases this
caused loss of node discovery. Corrected the reftaking around nvmet
plogis.
Nodes that experience devloss now get released from the node list now that
there is a proper reference taking.
Link: https://lore.kernel.org/r/20201115192646.12977-3-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a remote port is disconnected and disappears, its node structure
(ndlp) stays allocated and on a vport node list. While on the list it can
be matched, thus requires validation checks on state to be added in
numerous code paths. If the node comes back, its possible for there to be
multiple node structures for the same device on the vport node list. There
is no reason to keep the node structure around after it is no longer in
existence, and the current implementation creates problems for itself
(multiple nodes) and lots of unnecessary code for state validation.
Additionally, the reference taking on the node structure didn't follow the
normal model used by the kernel kref api. It included lots of odd logic to
match state with reference count. The combination of this odd logic plus
the way it was implicitly used in the discovery engine made its reference
taking implementation suspect and extremely hard to follow.
Change the driver such that the reference taking routines are now normal
ref increments/decrements and callout on refcount=0.
With this in place, the rework can be done such that the node structure is
fully removed and deallocated when the remote port no longer exists and all
references are removed. This removal logic, and the basic ref counting are
intrically tied, thus in a single patch.
Link: https://lore.kernel.org/r/20201115192646.12977-2-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On devices that support FCP sequence error recovery, which attempts to
preserve the devices login across link bounce, adisc is used for device
validation. Turns out the device fc4 type is cleared as part of the link
bounce, but the ADISC handling doesn't restore the FC4 support as it
normally would with a PRLI. This caused situations where the device wasn't
reregistered with the transport thus scan logic and LUN discovery never
kicked in.
In the ADISC completion handling, reset the fc4 type so that transport port
reregistration occurs with the remote port.
Link: https://lore.kernel.org/r/20200803210229.23063-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nportdisc.c:1079: warning: Function parameter or member 'ndlp' not described in 'lpfc_release_rpi'
Link: https://lore.kernel.org/r/20200723122446.1329773-20-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current logging methods typically end up requesting a reproduction with
a different logging level set to figure out what happened. This was mainly
by design to not clutter the kernel log messages with things that were
typically not interesting and the messages themselves could cause other
issues.
When looking to make a better system, it was seen that in many cases when
more data was wanted was when another message, usually at KERN_ERR level,
was logged. And in most cases, what the additional logging that was then
enabled was typically. Most of these areas fell into the discovery machine.
Based on this summary, the following design has been put in place: The
driver will maintain an internal log (256 elements of 256 bytes). The
"additional logging" messages that are usually enabled in a reproduction
will be changed to now log all the time to the internal log. A new logging
level is defined - LOG_TRACE_EVENT. When this level is set (it is not by
default) and a message marked as KERN_ERR is logged, all the messages in
the internal log will be dumped to the kernel log before the KERN_ERR
message is logged.
There is a timestamp on each message added to the internal log. However,
this timestamp is not converted to wall time when logged. The value of the
timestamp is solely to give a crude time reference for the messages.
Link: https://lore.kernel.org/r/20200630215001.70793-14-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During driver unload/reload testing, the NVMe initiator would not
re-establish connectivity to NVMe controllers on reload.
The failing NVMe array supports concurrent FCP and NVMe operation via
different nport_id's. The array was repeatedly sending an ADISC every 2
seconds after PLOGI completed and while NVMe subsystems were executing
discovery. The target would continue this state for roughly 45 seconds.
The driver's current behavior on ADISC receipt is to validate a the ADISC
vs the device and issue a RESUME_RPI to restore transmission. The receipt
of the ADISC effectively caused a driver to take actions similar to a
logout and login for the remote port, causing the deregistration of the
nvme rport and a subsequent re-registration. This caused a constant reset
and re-connect of the NVMe controller while this 45s window occurred. There
was no need for the state changes as ADISC does not change login state.
This patch corrects this behavior by validating if the remoteport is
already logged in (MAPPED) and when true, avoids the call to set the ndlp
state to MAPPED, which triggers the unreg/re-reg. Thus ADISC does not
change the login state of the node.
Link: https://lore.kernel.org/r/20200630215001.70793-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As the nvmet layer does not have the concept of a remoteport object, which
can be used to identify the entity on the other end of the fabric that is
to receive an LS, the hosthandle was introduced. The driver passes the
hosthandle, a value representative of the remote port, with a ls request
receive. The LS request will create the association. The transport will
remember the hosthandle for the association, and if there is a need to
initiate a LS request to the remote port for the association, the
hosthandle will be used. When the driver loses connectivity with the
remote port, it needs to notify the transport that the hosthandle is no
longer valid, allowing the transport to terminate associations related to
the hosthandle.
This patch adds support to the driver for the hosthandle. The driver will
use the ndlp pointer of the remote port for the hosthandle in calls to
nvmet_fc_rcv_ls_req(). The discovery engine is updated to invalidate the
hosthandle whenever connectivity with the remote port is lost.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A lot of files in lpfc include nvme headers, building up relationships that
require a file to change for its headers when there is no other change
necessary. It would be better to localize the nvme headers.
There is also no need for separate nvme (initiator) and nvmet (tgt)
header files.
Refactor the inclusion of nvme headers so that all nvme items are
included by lpfc_nvme.h
Merge lpfc_nvmet.h into lpfc_nvme.h so that there is a single header used
by both the nvme and nvmet sides. This prepares for structure sharing
between the two roles. Prep to add shared function prototypes for upcoming
shared routines.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix sparse warning:
drivers/scsi/lpfc/lpfc_nportdisc.c:344:1: warning:
symbol 'lpfc_defer_acc_rsp' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20200107014956.41748-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVMe device re-discovery does not complete. Dev_loss_tmo messages seen on
initiator after recovery from a link disturbance.
The failing case is the following:
When the driver (as a NVME target) receives a PLOGI, the driver initiates
an "unreg rpi" mailbox command. While the mailbox command is in progress,
the driver requests that an ACC be sent to the initiator. The target's ACC
is received by the initiator and the initiator then transmits a PLOGI. The
driver receives the PLOGI prior to receiving the completion for the PLOGI
response WQE that sent the ACC. (Different delivery sources from the hw so
the race is very possible). Given the PLOGI is prior to the ACC completion
(signifying PLOGI exchange complete), the driver LS_RJT's the PRLI. The
"unreg rpi" mailbox then completes. Since PRLI has been received, the
driver transmits a PLOGI to restart discovery, which the initiator then
ACC's. If the driver processes the (re)PLOGI ACC prior to the completing
the handling for the earlier ACC it sent the intiators original PLOGI,
there is no state change for completion of the (re)PLOGI. The ndlp remains
in "PLOGI Sent" and the initiator continues sending PRLI's which are
rejected by the target until timeout or retry is reached.
Fix by: When in target mode, defer sending an ACC for the received PLOGI
until unreg RPI completes.
Link: https://lore.kernel.org/r/20191218235808.31922-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: aacraid, ufs, zfcp,
NCR5380, lpfc, qla2xxx, smartpqi, hisi_sas, target, mpt3sas, pm80xx
plus a whole load of minor updates and fixes. The two major core
changes are Al Viro's reworking of sg's handling of copy to/from user,
Ming Lei's removal of the host busy counter to avoid contention in the
multiqueue case and Damien Le Moal's fixing of residual tracking
across error handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXeKvHCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQJMAQDAjlAi
SNfbyndMqyf+rZGWufDI+43Up1VvW9GeWJHeDwEAxfO5XZsCks2uT8UxXhpEp9L7
HkiUww3zbcgl0FWFkUM=
=cdVU
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: aacraid, ufs, zfcp,
NCR5380, lpfc, qla2xxx, smartpqi, hisi_sas, target, mpt3sas, pm80xx
plus a whole load of minor updates and fixes.
The major core changes are Al Viro's reworking of sg's handling of
copy to/from user, Ming Lei's removal of the host busy counter to
avoid contention in the multiqueue case and Damien Le Moal's fixing of
residual tracking across error handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (251 commits)
scsi: bnx2fc: timeout calculation invalid for bnx2fc_eh_abort()
scsi: target: core: Fix a pr_debug() argument
scsi: iscsi: Don't send data to unbound connection
scsi: target: iscsi: Wait for all commands to finish before freeing a session
scsi: target: core: Release SPC-2 reservations when closing a session
scsi: target: core: Document target_cmd_size_check()
scsi: bnx2i: fix potential use after free
Revert "scsi: qla2xxx: Fix memory leak when sending I/O fails"
scsi: NCR5380: Add disconnect_mask module parameter
scsi: NCR5380: Unconditionally clear ICR after do_abort()
scsi: NCR5380: Call scsi_set_resid() on command completion
scsi: scsi_debug: num_tgts must be >= 0
scsi: lpfc: use hdwq assigned cpu for allocation
scsi: arcmsr: fix indentation issues
scsi: qla4xxx: fix double free bug
scsi: pm80xx: Modified the logic to collect fatal dump
scsi: pm80xx: Tie the interrupt name to the module instance
scsi: pm80xx: Controller fatal error through sysfs
scsi: pm80xx: Do not request 12G sas speeds
scsi: pm80xx: Cleanup command when a reset times out
...
Prior to the last FC-NVME-2 draft, SLER and CONF were independent. SLER
now requires CONF to be set.
Revise the NVME PRLI checking to look for both inorder to enable SLER.
Link: https://lore.kernel.org/r/20191105005708.7399-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When operating in private loop mode, PLOGI exchanges are racing and the
driver tries to abort it's PLOGI. But the PLOGI abort ends up terminating
the login with the other end causing the other end to abort its PLOGI as
well. Discovery never fully completes.
Fix by disabling the PLOGI abort when private loop and letting the state
machine play out.
Link: https://lore.kernel.org/r/20191018211832.7917-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The initial lpfc_desc_set_adisc implementation in commit
dea3101e0a ("lpfc: add Emulex FC driver version 8.0.28") enabled ADISC if
cfg_use_adisc && RSCN_MODE && FCP_2_DEVICE
In commit 92d7f7b0cd ("[SCSI] lpfc: NPIV: add NPIV support on top of
SLI-3") this changed to
(cfg_use_adisc && RSC_MODE) || FCP_2_DEVICE
and later in commit ffc954936b ("[SCSI] lpfc 8.3.13: FC Discovery Fixes
and enhancements.") to
(cfg_use_adisc && RSC_MODE) || (FCP_2_DEVICE && FCP_TARGET)
A customer reports that after a devloss, an ADISC failure is logged. It
turns out the ADISC flag is set even the user explicitly set lpfc_use_adisc
= 0.
[Sat Dec 22 22:55:58 2018] lpfc 0000:82:00.0: 2:(0):0203 Devloss timeout on WWPN 50:01:43:80:12:8e:40:20 NPort x05df00 Data: x82000000 x8 xa
[Sat Dec 22 23:08:20 2018] lpfc 0000:82:00.0: 2:(0):2755 ADISC failure DID:05DF00 Status:x9/x70000
[mkp: fixed Hannes' email]
Fixes: 92d7f7b0cd ("[SCSI] lpfc: NPIV: add NPIV support on top of SLI-3")
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: James Smart <james.smart@broadcom.com>
Link: https://lore.kernel.org/r/20191022072112.132268-1-dwagner@suse.de
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/lpfc/lpfc_nportdisc.c:290:1: warning: symbol 'lpfc_defer_pt2pt_acc' was not declared. Should it be static?
Link: https://lore.kernel.org/r/1570183477-137273-1-git-send-email-zhengbin13@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After exchanging PLOGI on an SLI-3 adapter, the PRLI exchange failed. Link
trace showed the port was assigned a non-zero n_port_id, but didn't use the
address on the PRLI. The assigned address is set on the port by the
CONFIG_LINK mailbox command. The driver responded to the PRLI before the
mailbox command completed. Thus the PRLI response used the old n_port_id.
Defer the PRLI response until CONFIG_LINK completes.
Link: https://lore.kernel.org/r/20190922035906.10977-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FC-NVMe-2 added support for sequence level error recovery in the FC-NVME
protocol. This allows for the detection of errors and lost frames and
immediate retransmission of data to avoid exchange termination, which
escalates into NVMeoFC connection and association failures. A significant
RAS improvement.
The driver is modified to indicate support for SLER in the NVMe PRLI is
issues and to check for support in the PRLI response. When both sides
support it, the driver will set a bit in the WQE to enable the recovery
behavior on the exchange. The adapter will take care of all detection and
retransmission.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to see real addresses, convert %p with %px for kernel addresses
and replace %p with %pf for functions.
While converting, standardize on "x%px" throughout (not %px or 0x%px).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a target issues an ADISC to the port and the target is a NVME target,
the driver is inadvertantly invalidating the login and marking the remote
port as logged out. Communication with the target is lost.
Revise the ADISC check so that FCP or NVME targets will be marked valid at
the end of ADISC processing. Enhance logging to recognize condition
better.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some remote ports may be slow in registering their GID_FT protocol
information with the fabric. If the remote port is an initiator, it may
send PLOGI to the port before the GID_FT logic is complete. Meaning, after
accepting the PLOGI, when the driver may see no response to the GID_FT that
is issued after the login to determine the protocols supported so that
proper PRLI's may be transmit. If the driver has no fc4 information, it
currently stops and the remote port is not discovered.
Fix by issuing a LOGO when there is no GID_FT information. The LOGO
completion handling will attempt to re-login if the nport_id is still
present.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In cases of remote-port-side cable pull/replug, there happens to be a
target that upon replug will send the port a PLOGI, a PRLI, and a LOGO.
When this sequence is received by the driver, the PLOGI accepted and a
GFT_ID is issued to find the protocol support for the remote port. While
the GFT_ID is outstanding, a LOGO is received. The driver logs the remote
port out and unregisters the RPI and schedules a new PLOGI transmission.
However, the GFT_ID was not terminated. When it completed, the driver
attempted to transition the remote port to PRLI transmission, which cancels
the PLOGI scheduling. The PRLI transmit attempt is rejected by the adapter
as the remote port is not logged in. No retry is attempted as it's expected
the logout is noted and the supposedly scheduled PLOGI should address the
state. As there is no PLOGI, the remote port does not get re-discovered.
Fix by aborting the outstanding GFT_ID if the related remote port is logged
out.
Ensure a PRLI transmit attempt only occurs if the remote port is logging
in. This avoids the incorrect attempt while logged out.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but avoids that the compiler
complains about set-but-not-used variables when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler warns about missing fall-through
annotation when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler complains about missing declarations
when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For files modified as part of 12.2.0.0 patches, update copyright to 2019
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The conversion to enable SCSI and NVME fc4 support ran into an issue with
NPIV support. With NVME, NPIV is not currently supported, but with SCSI it
was. The driver reverted to its lowest setting meaning NPIV with SCSI was
not allowed.
Convert the NPIV checks and implementation so that SCSI can continue to
allow NPIV support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is getting hit with 100s of RSCNs during remote port address
changes. Each of those RSCN's ends up generating UNREG_RPI and REG_PRI
mailbox commands. The discovery engine within the driver doesn't wait for
the mailbox command completions. Instead it sets state flags and moves
forward. At some point, there's a massive backlog of mailbox commands which
take time for the adapter to process. Additionally, it appears there were
duplicate events from the switch so the driver generated duplicate mailbox
commands for the same remote port. During this window, failures on PLOGI
and PRLI ELS's are see as the adapter is rejecting them as they are for
remote ports that still have pending mailbox commands.
Streamline the discovery engine so that PLOGI log checks for outstanding
UNREG_RPIs and defer the processing until the commands complete. This
better synchronizes the ELS transmission vs the RPI registrations.
Filter out multiple UNREG_RPIs being queued up for the same remote port.
Beef up log messages in this area.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver data structure for managing a mailbox command contained two
context fields. Unfortunately, the context were considered "generic" to be
used at the whim of the command code. Of course, one section of code used
fields this way, while another did it that way, and eventually there were
mixups.
Refactored the structure so that the generic contexts become a node context
and a buffer context and all code standardizes on their use.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The switches seem to respond faster to GID_PT vs GID_FT NameServer
queries. Add support for GID_PT to be used over GID_FT to enable
faster storage failover detection. Includes addition of new module
parameter to select between GID_PT and GID_FT (GID_FT is default).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An address change for a remote port cause PRLI for the wrong protocol
to be sent. The node copy done in the discovery code skipped copying
the fc4 protocols supported as well.
Fix the copy logic for the address change. Beefed up log messages in
this area as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a LOGO in response to an ABTS timeout, a PLOGI wasn't issued to
re-establish the login. An nlp_type check in the LOGO completion
handler failed to restart discovery for NVME targets. Revised the
nlp_type check for NVME as well as SCSI.
While reviewing the LOGO handling a few other issues were seen and
were addressed:
- Better lock synchronization around ndlp data types
- When the ABTS times out, unregister the RPI before sending the LOGO
so that all local exchange contexts are cleared and nothing received
while awaiting LOGO/PLOGI handling will be accepted.
- LOGO handling optimized to:
Wait only R_A_TOV for a response.
It doesn't need to be retried on timeout. If there wasn't a
response, a PLOGI will be sent, thus an implicit logout
applies as well when the other port sees it.
If there is a response, any kind of response is considered "good"
and the XRI quarantined for a exchange qualifier window.
- PLOGI is issued as soon a LOGO state is resolved.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver only sends NVME PRLI to a device that also supports FCP. This resuls
in remote ports that don't have fc_remote_ports created for them. The driver
is clearing the nlp_fc4_type for a ndlp at the wrong time.
Fix by moving the nlp_fc4_type clearing to the discovery engine in the
DEVICE_RECOVERY state. Also ensure that rport registration is done for all
nlp_fc4_types.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Performance is affected when target queue depth is tracked. An atomic
counter is incremented on the submission path which competes with it being
decremented on the completion path. In addition, multiple CPUs can
simultaniously be manipulating this counter for the same ndlp.
Reduce the overhead by only performing the target increment/decrement when
the target queue depth is less than the overall adapter depth, thus is
actually meaningful.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For ABORT_XRI_CN command, firmware identifies XRI to abort by IOTAG and RPI
combination. For ELS aborts, driver specifies IOTAG correctly but RPI is
not specified.
Fix by setting RPI in WQE.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change references from "Broadcom Limited" to "Broadcom Inc." in the
copyright message. Update copyright duration if not yet updated for 2018.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under large configurations, the driver would start to log message 6065 -
NVME out of buffers (exchanges).
The driver is using the ndlp cmd_qdepth value when determining the max
outstanding ios for an adapter. This value, by default, is set to 65536,
which exceeds the maximum exchange counts supported on an adapter. The ndlp
cmd_qdepth has no relevance and outstanding io count should be capped at
the max exchange count with IO requests beyond that level getting bounced
back with an EBUSY status so that they are retried by the block layer.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nodelist entry for SCSI array ends up in UNMAPPED state. This is due to
illegal discovery State machine transition because of two PRLIs and the
first one failing with LS_RJT. Also, the error path was designed
assuming the PRLIs complete in the order they were sent, FCP first, then
NVME. In a failing case, the array thinks about the first PRLI (FCP),
but issues LS_RJT for the 2nd PRLI immediately.
Fix PRLI completion error path for the ordering expectation. Ensure the
discovery state machine update is not set until all outstanding PRLIs
are complete.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
First Burst support was not properly indicated in NVMe PRLI.
Correct the bit position and the logic to check and set first burst support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated Copyright in files updated 11.4.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise the NVME PRLI to indicate CONF support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the lpfc discovery engine, when as a nvme target, where the driver
was performing mailbox io with the adapter for port login when a NVME
PRLI is received from the host. Rather than queue and eventually get
back to sending a response after the mailbox traffic, the driver
rejected the io with an error response.
Turns out this particular initiator didn't like the rejection values
(unable to process command/command in progress) so it never attempted a
retry of the PRLI. Thus the host never established nvme connectivity
with the lpfc target.
By changing the rejection values (to Logical Busy/nothing more), the
initiator accepted the response and would retry the PRLI, resulting in
nvme connectivity.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When enabled for both SCSI and NVME support, and connected pt2pt to a
SCSI only target, the driver nodelist entry for the remote port is left
in PRLI_ISSUE state and no SCSI LUNs are discovered. Works fine if only
configured for SCSI support.
Error was due to some of the prli points still reflecting the need to
send only 1 PRLI. On a lot of fabric configs, targets were NVME only,
which meant the fabric-reported protocol attributes were only telling
the driver one protocol or the other. Thus things worked fine. With
pt2pt, the driver must send a PRLI for both protocols as there are no
hints on what the target supports. Thus pt2pt targets were hitting the
multiple PRLI issues.
Complete the dual PRLI support. Track explicitly whether scsi (fcp) or
nvme prli's have been sent. Accurately track protocol support detected
on each node as reported by the fabric or probed by PRLI traffic.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Handling a rcv'ed PRLI incorrectly can cause the ndlp to end up in the
wrong state or the driver to ACC and PRLI when it should send LS_RJT.
The cause was due to the driver not properly looking at the PRLI type
and taking the multiple protocol support into consideration.
Resolved by adding checks in the various PRLI receive points to validate
PRLI type and reject if not valid for the enabled protocols and mode
(host vs target).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver crashes when attempting to use a freed ndpl pointer.
The pci_remove_one handler runs on a separate kernel thread. The order
of the removal is starting by freeing all of the ndlps and then
disabling interrupts. In between these two events the driver can still
receive an ELS and process it. When it tries to use the ndlp pointer
will be NULL
Change the order of the pci_remove_one vs disable interrupts so that
interrupts are disabled before the ndlp's are freed.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After link bounce in a NVME Pt2Pt config, the driver managed to map the
same nport twice, resulting in multiple device nodes for the same
namespace.
In Pt2Pt, the driver must send PRLI's for both (scsi) FCP and NVME
rather than using fabric aids. The driver was inconsistent on handling
various PRLI completions, especially rejects, which had reject codes
cross the different protocol PRLI completions.
Fixed to perform the following: if nvmet mode (fc port can only be a
nvme target) - rejects all unsolicitly FCP PRLI's. Never issues a FCP
PRLI.
The multiple protocol PRLI's are sent simultaneously. However, driver
will now only state transition after both PRLI's are complete. New flags
were added to aid tracking the responses from the different PRLI's.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the switch blade is pulled out then plugged back in, the driver
does not issue a PLOGI to the target
When the switch blade is pulled out, it does not reset the link. The
driver ends up issuing a LOGO to the target, and finally sees devloss.
Since the driver believes that a LOGO is outstanding, it does not issue
a PLOGI to the target upon link up
Correct by placing the ndlp in UNUSED state When devloss happens in
LOGO_ISSUE state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver does not discover targets when in loop mode.
The NLP type is correctly getting set when a fabric connection is
detected but, not for loop. The unknown NLP type means that the driver
does not issue a PRLI when in loop topology. Thus target discovery
fails.
Fix by checking the topology during discovery. If it is loop, set the
NLP FC4 type to FCP.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We might have a NULL pring in lpfc_els_abort(), for example on error
recovery path, since queues are destroyed during error recovery
mechanism.
In this case, we should just drop the abort since the queues will be
recreated anyway. This patch just verifies for NULL pointer and stop the
abortion of the queue in case of a NULL pring.
Also, this patch converts return type of lpfc_els_abort() from int to
void, since it's not checked anywhere.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Reported-by: Naresh Bannoth <nbannoth@in.ibm.com>
Tested-by: Raphael Silva <raphasil@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code review of NVMEI's FC_PORT_ROLE_NVME_DISCOVERY looked wrong.
Discussions with storage architecture team clarified NVMEI's audit of
the PRLI response port roles. Following up discussion with code review
showed a few minor corrections were required - especially in
anticipation of NVME auto discovery.
During PRLI, NVMEI should sent prli_init - which it it does. NVMET
should send prli_tgt and prli_disc - which it does. When NVMEI receives
a PRLI Response now, it audits the incoming target bits and stores the
attributes in the corresponding NDLP. Later, when NVMEI registers the
NVME rport, it uses the stored ndlp attributes to set the rport
port_roles correctly.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVMET didn't have any RSCN handling at all and
would not execute implicit LOGO when receiving a PLOGI
from an rport that NVMET had in state UNMAPPED.
Clean up the logic in lpfc_nlp_state_cleanup for
initiators (FCP and NVME). NVMET should not respond to
RSCN including allocating new ndlps so this code was
conditionalized when nvmet_support is true. The check
for NLP_RCV_PLOGI in lpfc_setup_disc_node was moved
below the check for nvmet_support to allow the NVMET
to recover initiator nodes correctly. The implicit
logo was introduced with lpfc_rcv_plogi when NVMET gets
a PLOGI on an ndlp in UNMAPPED state. The RSCN handling
was modified to not respond to an RSCN in NVMET. Instead
NVMET sends a GID_FT and determines if an NVMEP_INITIATOR
it has is UNMAPPED but no longer in the zone membership.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Update copyrights to 2017 for all files touched in this patch set
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Target: Merge into FC discovery
Adds NVME PRLI handling and Nameserver registrations for NVME
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Initiator: Tie in to NVME Fabrics nvme_fc LLDD initiator api
Adds the routines to:
- register and deregister the FC port as a nvme-fc initiator localport
- register and deregister remote FC ports as a nvme-fc remoteport
- binding of nvme queues to adapter WQs
- send/perform NVME LS's
- send/perform NVME FCP initiator io operations
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Initiator: Merge into FC discovery
Adds NVME PRLI support and Nameserver registrations and Queries for NVME
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Initiator: Base modifications
This patch adds base modifications for NVME initiator support.
The base modifications consist of:
- Formal split of SLI3 rings from SLI-4 WQs (sometimes referred to as
rings as well) as implementation now widely varies between the two.
- Addition of configuration modes:
SCSI initiator only; NVME initiator only; NVME target only; and
SCSI and NVME initiator.
The configuration mode drives overall adapter configuration,
offloads enabled, and resource splits.
NVME support is only available on SLI-4 devices and newer fw.
- Implements the following based on configuration mode:
- Exchange resources are split by protocol; Obviously, if only
1 mode, then no split occurs. Default is 50/50. module attribute
allows tuning.
- Pools and config parameters are separated per-protocol
- Each protocol has it's own set of queues, but share interrupt
vectors.
SCSI:
SLI3 devices have few queues and the original style of queue
allocation remains.
SLI4 devices piggy back on an "io-channel" concept that
eventually needs to merge with scsi-mq/blk-mq support (it is
underway). For now, the paradigm continues as it existed
prior. io channel allocates N msix and N WQs (N=4 default)
and either round robins or uses cpu # modulo N for scheduling.
A bunch of module parameters allow the configuration to be
tuned.
NVME (initiator):
Allocates an msix per cpu (or whatever pci_alloc_irq_vectors
gets)
Allocates a WQ per cpu, and maps the WQs to msix on a WQ #
modulo msix vector count basis.
Module parameters exist to cap/control the config if desired.
- Each protocol has its own buffer and dma pools.
I apologize for the size of the patch.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
----
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a link bounce, when a remote port issues a LOGO while a REGLOGIN
is pending on that port, the driver does not clean up the ndlp
structure. May result in stack traces in the console log.
Fix: Clear the NLP_REG_LOGIN_SEND flag on the ndlp in the routine
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix mbox reuse in PLOGI completion. Moved allocations so that buffer
properly init'd.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix RegLogin failed error seen on Lancer FC during port bounce
Fix the statemachine and ref counting.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the FLOGI discovery logic to comply with T11 standards
We weren't properly setting fabric parameters, such as R_A_TOV and E_D_TOV,
when we registered the vfi object in default configs and pt2pt configs.
Revise to now pass service params with the values to the firmware and
ensure they are reset on link bounce. Required reworking the call sequence
in the discovery threads.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove set but not used variables.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The domain controller PLOGI's concurrent with prior LOGO's/unreg_rpi's
completing created a race condition where driver rpi ref count can
inadvertantly hit 0 and the rpi attempted to be freed. This error
sometimes resulted in Warning messages indicating kref.h via
lfpc_nlp_get+0x128.
Correct by dropping any new PLOGI until the prior nport state has settled.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
We inadvertantly took the path to recreate the vport while in a
driver teardown path
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Update copyright to 2015
Signed-off-by: Dick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Fixed High priority issues from lpfc given by fortify source code scan.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Dick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixed NMI watch dog panic's when resetting the hba.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make compliant with FC specs by sending LOGO after ABTS timeouts
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
SLI related fixes:
- Fix REG_RPI fails on SLI4 HBA putting NPort into NPR state (126230)
- Fix ELS FDISC failing with local reject / invalid RPI. (126350)
- Fix reset port when reset is needed during fw_dump (125807)
- Fix unbounded firmware revision string from port cause panic (126560)
- Fix driver behavior when receiving an ADISC (126654)
- Fix driver not returning when bad ndlp found in abts error event
handling (126209)
- Add more driver logs in area of SLI4 port error attention and reset
recovery (126813, 124466)
- Fix failure in handling large CQ/EQ identifiers in an IOV
environment (126856)
- Fix for driver using duplicate RPIs after lancer port reset (126723)
- Clear vport->fc_myDID in lpfc_els_issue_fdisc to guarentee a
zero SID (126779, 126897)
- Fix for SLI4 Port delivery for BLS ABORT ACC (126289)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FC and SCSI Discovery Fixes:
- Clear the virtual fabrics bit (word 1 bit 30) when sending the FLOGI
and FDISC. (CR 124339)
- Return a MLQUEUE_DEVICE_BUSY if the driver detects that an I/O is being
retried too quickly (CR 124668)
- Remove NDLP reference put in lpfc_cmpl_els_logo_acc for all but fabric
nodes (CR 123924)
- Only retry FDISCs every second and stop retrying after devloss number
of retries (CR 13939)
- Check to see if vports are unloading before adding them to the vport
work array. (CR 124996)
- Fixed illegal state transition during driver unload (CR 124191)
- Added missing protection on setting/clearing of vport->fc_flag bit (CR 126002)
- Set NPIV flag in lpfc_mbx_process_link_up for all ports sli3 and
above. (CR 126094)
- Clear FCP command bytes that are not used. (CR 126209)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds support for hardware that returns resource ids via
extents rather than contiguous ranges.
[jejb: checkpatch.pl fixes]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Miscellaneous Fixes and Corrections
- Remove the memset in the lpfc_sli4_remove_rpi_hdrs call.
- Correct swapping of SGE word 2 relative to offset value
- Reorganize CQ and EQ usage to comply with SLI4 Specification.
- Expand the driver to check the rn bit. Only detect an error if the error bit
is set and the RN bit is NOT set.
- If mailbox completion code is not success AND the mailbox status is success,
then and only then will the driver overwrite the mailbox status.
- When driver initializing device, if the device is on a PCIe bus, set
PCI's "needs fundamental reset" bit so that EEH uses fundamental reset
instead of hot reset for recovery.
- Prevent driver from using new WWN when changed in firmware (until driver
reload)
- When HBA reports maximum SGE size > 0xffffffff (infinite), override
with 0x80000000.
- Fixed potential missed SLI4 device initialization failure conditions.
- Added 100ms delay before driver action following IF_TYPE_2 function reset.
- Reverted patch to UNREG/REG on PLOGI to mapped/unmapped node.
- Add a check for the CVL received flag in the fcf inuse routine to avoid
unregistering the fcf if Devloss fires before Delay discover timer fires.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
FC Discovery changes
- Treat received PLOGI while logged in as a relogin (unregister and reregister).
- Added a timer to delay Nport discovery when clean bit is cleared and Fabric
portname/nodename/FCID is changed.
- Invalidate Port's DID when receiving PLOGI from p2p port with CONFIG_PORT
mailbox command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Updated commands used for ELS to utilize VPI
Allocate RPI at node creation time and pass in ELS commnads.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Retry PLOGI up to 48 times when LS_RJT reason is
"Unable to supply requested data."
- When dev loss timeout occures do not change state if there
is an outstanding REG_LOGIN.
- Add logic to ignore REG_LOGIN completion if discovery is
restarted while waiting for REG_LOGIN.
- Only change state on REG_LOGIN completion if still in
state waiting for REG_LOGIN completion.
- Only send ADISCs to FCP-2 Targets (not Initiators).
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add code to prevent unreg_vpi mailbox command from failing.
- Add code to reset the HBA if unreg_vpi mailbox fails with busy status.
- Remove code that was clearing the nlp_type stored during rport discovery.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Enable NPIV by default.
- Added code to handle unsolicited LOGO on physical port.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Discovery relates changes:
- Separated VPI_REGISTERED state of physical port into VFI_REGISTERED and
VPI_REGISTERED state so that driver can unregister physical port VPI
independent of VFI.
- Add code to unregister, re-init and re-register physical port VPI
when physical port NportID change.
- Add code to unregister and re-register VPI of a vport when its Nport
ID change.
- Add code in FDISC completion path to re-start FLOGI discovery when
a FDISC complete with LOGIN_REQUIRED reason code.
- Fix a memory leak in lpfc_init_vpi_cmpl
- Add code to start a timer for vport to retry FDISC when CVL is received
by a vport or physical port. If all Nports receive CVLs, then all timers
are cancelled and a logical link level discovery will be started after
one second.
- Flush ELS commands after killing all delayed ELS commands.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix hardware/SLI relates issues:
- Handle XB bit so that ELS XRIs are not prematurely released.
- Handle XB bit so that FCP XRIs are not prematurely released.
- Define new security SLI Commands.
- Remove unused security SLI commands
- Skip receive data size parameter check on received FLOGI.
- Added LPFC_USE_FCPWQIDX flag to iocb to force SLI layer
to submit abort WQE on same WQ as the command WQE.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FC protocol fixes.
- Fix send sequence logic to handle multi SGL IOCBs.
- Fix FDISC completion always setting VPORT state to failed.
- Ported the fix on reporting of max_vpi to uppper layer.
- Fix incorrect number of Vports allowed to be created.
- Fixed Dead FCoE port after creating vports.
- Added handling of ELS request for Reinstate Recovery Qualifier (RRQ)
- Handle unsolicited CT exchange initiator receiving CT exchange ABTS
- Migrate LUN queue depth ramp up code to scsi mid-layer.
- Made ABTS WQE go to the same WQ as the WQE to be aborted.
- Fix Vport does not rediscover after FCF goes away.
- Fixed lpfc_unreg_vfi failure after devloss timeout.
- Fixed RPI bit leak.
- Fix hbq pointer corruption during target discovery.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Contains the following changes:
- Force vport to send LOGO to fabric controller when deleting vport
- Fixed driver failing to register login when a PLOGI is received
- Fixes for FIP discovery
- Added stricter checks for FCF addressing mode
- Added code to send only FLOGI, FDISC and LOGO to Fabric controller as FIP
- Fixed handling of LOGO from Fabric port
- Fixed consecutive link up events skipped link_down processing
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update of copyrights on modified files
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SLI4 supports both FC and FCOE, with some extended topology objects.
This patch adss support for the objects, and updates the disovery
engines for their use.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The mailbox commands themselves are the same, or very similar to
their SLI3 counterparts. This patch genericizes mailbox command
handling and adds support for the new SLI4 mailbox queue.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds new hardware and interface definitions.
Adds new interface routines - utilizing the reorganized layout of the
driver. Adds SLI-4 specific functions for attachment, initialization,
teardown, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
