A live partition migration (LPM) results in a CRQ disconnect similar to a
hard reset. In this LPM case the hypervisor mostly preserves the CRQ
transport such that it simply needs to be reenabled. However, the
capabilities may have changed such as fewer channels, or no channels at
all. Further, its possible that there may be sub-CRQ support, but no
channel support. The CRQ reenable path currently doesn't take any of this
into consideration.
For simplicity release and reinitialize sub-CRQs during reenable, and set
do_enquiry and using_channels with the appropriate values to trigger
channel renegotiation.
Link: https://lore.kernel.org/r/20210302230543.9905-6-tyreld@linux.ibm.com
Fixes: 3034ebe263 ("scsi: ibmvfc: Add alloc/dealloc routines for SCSI Sub-CRQ Channels")
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The H_FREE_SUB_CRQ hypercall can return a retry delay return code that
indicates the call needs to be retried after a specific amount of time
delay. The error path to free a sub-CRQ in case of a failure during channel
registration fails to capture the return code of H_FREE_SUB_CRQ which will
result in the delay loop being skipped in the case of a retry delay return
code.
Store the return code result of the H_FREE_SUB_CRQ call such that the
return code check in the delay loop evaluates a meaningful value. Also, use
the rtas_busy_delay() to check the rc value and delay for the appropriate
amount of time.
Link: https://lore.kernel.org/r/20210302230543.9905-5-tyreld@linux.ibm.com
Fixes: 39e461fddf ("scsi: ibmvfc: Map/request irq and register Sub-CRQ interrupt handler")
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A non-zero return code for H_REG_SUB_CRQ is currently treated as a failure
resulting in failing sub-CRQ setup. The case of H_CLOSED should not be
treated as a failure. This return code translates to a successful sub-CRQ
registration by the hypervisor, and is meant to communicate back that there
is currently no partner VIOS CRQ connection established as of yet. This is
a common occurrence during a disconnect where the client adapter can
possibly come back up prior to the partner adapter.
For non-zero return code from H_REG_SUB_CRQ treat a H_CLOSED as success so
that sub-CRQs are successfully setup.
Link: https://lore.kernel.org/r/20210302230543.9905-4-tyreld@linux.ibm.com
Fixes: 3034ebe263 ("scsi: ibmvfc: Add alloc/dealloc routines for SCSI Sub-CRQ Channels")
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A hard reset results in a complete transport disconnect such that the CRQ
connection with the partner VIOS is broken. This has the side effect of
also invalidating the associated sub-CRQs. The current code assumes that
the sub-CRQs are perserved resulting in a protocol violation after trying
to reconnect them with the VIOS. This introduces an infinite loop such that
the VIOS forces a disconnect after each subsequent attempt to re-register
with invalid handles.
Avoid the aforementioned issue by releasing the sub-CRQs prior to CRQ
disconnect, and driving a reinitialization of the sub-CRQs once a new CRQ
is registered with the hypervisor.
Link: https://lore.kernel.org/r/20210302230543.9905-3-tyreld@linux.ibm.com
Fixes: 3034ebe263 ("scsi: ibmvfc: Add alloc/dealloc routines for SCSI Sub-CRQ Channels")
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If ibmvfc_init_sub_crqs() fails ibmvfc_probe() simply parrots registration
failure reported elsewhere, and futher vhost->scsi_scrq.scrq == NULL is
indication enough to the driver that it has no sub-CRQs available. The
mq_enabled check can also be moved into ibmvfc_init_sub_crqs() such that
each caller doesn't have to gate the call with a mq_enabled check. Finally,
in the case of sub-CRQ setup failure setting do_enquiry can be turned off
to putting the driver into single queue fallback mode.
The aforementioned changes also simplify the next patch in the series that
fixes a hard reset issue, by tying a sub-CRQ setup failure and do_enquiry
logic into ibmvfc_init_sub_crqs().
Link: https://lore.kernel.org/r/20210302230543.9905-2-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver core ignores the return value of struct bus_type::remove()
because there is only little that can be done. To simplify the quest to
make this function return void, let struct vio_driver::remove() return
void, too. All users already unconditionally return 0, this commit makes
it obvious that returning an error code is a bad idea.
Note there are two nominally different implementations for a vio bus:
one in arch/sparc/kernel/vio.c and the other in
arch/powerpc/platforms/pseries/vio.c. This patch only adapts the powerpc
one.
Before this patch for a device that was bound to a driver without a
remove callback vio_cmo_bus_remove(viodev) wasn't called. As the device
core still considers the device unbound after vio_bus_remove() returns
calling this unconditionally is the consistent behaviour which is
implemented here.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Lijun Pan <ljp@linux.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[mpe: Drop unneeded hvcs_remove() forward declaration, squash in
change from sfr to drop ibmvnic_remove() forward declaration]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210225221834.160083-1-uwe@kleine-koenig.org
The UFS core has received a substantial rework this cycle. This in
turn has caused a merge conflict in linux-next. Merge 5.11/scsi-fixes
into 5.12/scsi-queue and resolve the conflict.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the various module parameter toggles for adjusting the MQ
characteristics at boot/load time as well as a device attribute for
changing the client scsi channel request amount.
Link: https://lore.kernel.org/r/20210114203148.246656-22-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Grab the queue and list lock for each Sub-CRQ and add any uncompleted
events to the host purge list.
Link: https://lore.kernel.org/r/20210114203148.246656-20-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In general the client needs to send Cancel MADs and task management
commands down the same channel as the command(s) intended to cancel or
abort. The client assigns cancel keys per LUN and thus must send a Cancel
down each channel commands were submitted for that LUN. Further, the client
then must wait for those cancel completions prior to submitting a LUN RESET
or ABORT TASK SET.
Add a cancel rsp iu syncronization field to the ibmvfc_queue struct such
that the cancel routine can sync the cancel response to each queue that
requires a cancel command. Build a list of each cancel event sent and wait
for the completion of each submitted cancel.
Link: https://lore.kernel.org/r/20210114203148.246656-19-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a helper routine for initializing a Cancel MAD. This will be useful for
a channelized client that needs to send Cancel commands down every channel
commands were sent for a particular LUN.
Link: https://lore.kernel.org/r/20210114203148.246656-18-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the ibmvfc client adapter requests channels it must submit a number of
Sub-CRQ handles matching the number of channels being requested. The VIOS
in its response will overwrite the actual number of channel resources
allocated which may be less than what was requested. The client then must
store the VIOS Sub-CRQ handle for each queue. This VIOS handle is needed as
a parameter with h_send_sub_crq().
Link: https://lore.kernel.org/r/20210114203148.246656-17-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the client has negotiated the use of channels all vfcFrames are
required to go down a Sub-CRQ channel or it is a protocoal violation. If
the adapter state is channelized submit vfcFrames to the appropriate
Sub-CRQ via the h_send_sub_crq() helper.
Link: https://lore.kernel.org/r/20210114203148.246656-16-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Extract the hwq id from a SCSI command and store it in the ibmvfc_event
structure to identify which Sub-CRQ to send the command down when channels
are being utilized.
Link: https://lore.kernel.org/r/20210114203148.246656-15-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Previous patches have plumbed the necessary Sub-CRQ interface and channel
negotiation MADs to fully channelize via hardware backed queues.
Advertise client support via NPIV Login capability IBMVFC_CAN_USE_CHANNELS
when the client bits have MQ enabled via vhost->mq_enabled, or when
channels were already in use during a subsequent NPIV Login. The later is
required because channel support is only renegotiated after a CRQ pair is
broken. Simple NPIV Logout/Logins require the client to continue to
advertise the channel capability until the CRQ pair between the client is
broken.
Link: https://lore.kernel.org/r/20210114203148.246656-14-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New NPIV_ENQUIRY_CHANNEL and NPIV_SETUP_CHANNEL management datagrams (MADs)
were defined in a previous patchset. If the client advertises a desire to
use channels and the partner VIOS is channel capable then the client must
proceed with channel enquiry to determine the maximum number of channels
the VIOS is capable of providing, and registering SubCRQs via channel setup
with the VIOS immediately following NPIV Login. This handshaking should not
be performed for subsequent NPIV Logins unless the CRQ connection has been
reset.
Implement these two new MADs and issue them following a successful NPIV
login where the VIOS has set the SUPPORT_CHANNELS capability bit in the
NPIV Login response.
Link: https://lore.kernel.org/r/20210114203148.246656-13-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create an irq mapping for the hw_irq number provided from phyp firmware.
Request an irq assigned our Sub-CRQ interrupt handler. Unmap these irqs at
Sub-CRQ teardown.
Link: https://lore.kernel.org/r/20210114203148.246656-12-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simple handler that calls Sub-CRQ drain routine directly.
Link: https://lore.kernel.org/r/20210114203148.246656-11-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The logic for iterating over the Sub-CRQ responses is similiar to that of
the primary CRQ. Add the necessary handlers for processing those responses.
Link: https://lore.kernel.org/r/20210114203148.246656-10-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Each Sub-CRQ has its own interrupt. A hypercall is required to toggle the
IRQ state. Provide the necessary mechanism via a helper function.
Link: https://lore.kernel.org/r/20210114203148.246656-9-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allocate a set of Sub-CRQs in advance. During channel setup the client and
VIOS negotiate the number of queues the VIOS supports and the number that
the client desires to request. Its possible that the final channel
resources allocated is less than requested, but the client is still
responsible for sending handles for every queue it is hoping for.
Also, provide deallocation cleanup routines.
Link: https://lore.kernel.org/r/20210114203148.246656-8-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sub-CRQs are registred with firmware via a hypercall. Abstract that
interface into a simpler helper function.
Link: https://lore.kernel.org/r/20210114203148.246656-6-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With the upcoming addition of Sub-CRQs the event pool size may vary
per-queue.
Add a size parameter to ibmvfc_init_event_pool() such that different size
event pools can be requested by ibmvfc_alloc_queue().
Link: https://lore.kernel.org/r/20210114203148.246656-5-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The event pool and CRQ used to be separate entities of the adapter host
structure and as such were allocated and freed independently of each
other. Recent work as defined a generic queue structure with an event pool
specific to each queue. As such the event pool for each queue shouldn't be
allocated/freed independently, but instead performed as part of the queue
allocation/free routines.
Move the calls to ibmvfc_event_pool_{init|free} into
ibmvfc_{alloc|free}_queue respectively. The only functional change here is
that the CRQ cannot be released in ibmvfc_remove until after the event pool
has been successfully purged since releasing the queue will also free the
event pool.
Link: https://lore.kernel.org/r/20210114203148.246656-4-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The next patch in this series reworks the event pool allocation calls to
happen within the individual queue allocation routines instead of as
independent calls.
Move the init/free routines earlier in ibmvfc.c to prevent undefined
reference errors when calling these functions from the queue allocation
code. No functional change.
Link: https://lore.kernel.org/r/20210114203148.246656-3-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce several new vhost fields for managing MQ state of the adapter as
well as initial defaults for MQ enablement.
Link: https://lore.kernel.org/r/20210114203148.246656-2-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While testing live partition mobility, we have observed occasional crashes
of the Linux partition. What we've seen is that during the live migration,
for specific configurations with large amounts of memory, slow network
links, and workloads that are changing memory a lot, the partition can end
up being suspended for 30 seconds or longer. This resulted in the following
scenario:
CPU 0 CPU 1
------------------------------- ----------------------------------
scsi_queue_rq migration_store
-> blk_mq_start_request -> rtas_ibm_suspend_me
-> blk_add_timer -> on_each_cpu(rtas_percpu_suspend_me
_______________________________________V
|
V
-> IPI from CPU 1
-> rtas_percpu_suspend_me
-> __rtas_suspend_last_cpu
-- Linux partition suspended for > 30 seconds --
-> for_each_online_cpu(cpu)
plpar_hcall_norets(H_PROD
-> scsi_dispatch_cmd
-> scsi_times_out
-> scsi_abort_command
-> queue_delayed_work
-> ibmvfc_queuecommand_lck
-> ibmvfc_send_event
-> ibmvfc_send_crq
- returns H_CLOSED
<- returns SCSI_MLQUEUE_HOST_BUSY
-> __blk_mq_requeue_request
-> scmd_eh_abort_handler
-> scsi_try_to_abort_cmd
- returns SUCCESS
-> scsi_queue_insert
Normally, the SCMD_STATE_COMPLETE bit would protect against the command
completion and the timeout, but that doesn't work here, since we don't
check that at all in the SCSI_MLQUEUE_HOST_BUSY path.
In this case we end up calling scsi_queue_insert on a request that has
already been queued, or possibly even freed, and we crash.
The patch below simply increases the default I/O timeout to avoid this race
condition. This is also the timeout value that nearly all IBM SAN storage
recommends setting as the default value.
Link: https://lore.kernel.org/r/1610463998-19791-1-git-send-email-brking@linux.vnet.ibm.com
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver's queuecommand routine is still wrapped to hold the host lock
for the duration of the call. This will become problematic when moving to
multiple queues due to the lock contention preventing asynchronous
submissions to mulitple queues. There is no real legitimate reason to hold
the host lock, and previous patches have insured proper protection of
moving ibmvfc_event objects between free and sent lists.
Link: https://lore.kernel.org/r/20210106201835.1053593-6-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drain the command queue and place all commands on a completion list.
Perform command completion on that list outside the host/queue locks.
Further, move purged command compeletions outside the host_lock as well.
Link: https://lore.kernel.org/r/20210106201835.1053593-5-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Define per-queue locks for protecting queue state and event pool sent/free
lists. The evt list lock is initially redundant but it allows the driver to
be modified in the follow-up patches to relax the queue locking around
submissions and completions.
Link: https://lore.kernel.org/r/20210106201835.1053593-4-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is currently a single command event pool per host. In anticipation of
providing multiple queues add a per-queue event pool definition and
reimplement the existing CRQ to use its queue defined event pool for
command submission and completion.
Link: https://lore.kernel.org/r/20210106201835.1053593-3-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The primary and async CRQs are nearly identical outside of the format and
length of each message entry in the dma mapped page that represents the
queue data. These queues can be represented with a generic queue structure
that uses a union to differentiate between message format of the mapped
page.
This structure will further be leveraged in a followup patcheset that
introduces Sub-CRQs.
Link: https://lore.kernel.org/r/20210106201835.1053593-2-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 2aa0102c66 ("scsi: ibmvfc: Use correlation token to tag commands")
sets the vfcFrame correlation token to the pointer handle of the associated
ibmvfc_event. However, that commit failed to cast the pointer to an
appropriate type which in this case is a u64. As such sparse warnings are
generated for both correlation token assignments.
ibmvfc.c:2375:36: sparse: incorrect type in argument 1 (different base types)
ibmvfc.c:2375:36: sparse: expected unsigned long long [usertype] val
ibmvfc.c:2375:36: sparse: got struct ibmvfc_event *[assigned] evt
Add the appropriate u64 casts when assigning an ibmvfc_event as a
correlation token.
Link: https://lore.kernel.org/r/20210106203721.1054693-1-tyreld@linux.ibm.com
Fixes: 2aa0102c66 ("scsi: ibmvfc: Use correlation token to tag commands")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The previous patch added support for the targetWWPN field in version 2 MADs
and vfcFrame structures.
Set the IBMVFC_CAN_SEND_VF_WWPN bit in our capabailites flag during NPIV
Login to inform the VIOS that this client supports the feature.
Link: https://lore.kernel.org/r/20201118011104.296999-7-tyreld@linux.ibm.com
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several version 2 MADs and the version 2 vfcFrame structures introduced a
new targetWWPN field for better identification of a target over the
scsi_id.
Set this field and MAD versioning fields when the VIOS advertises the
IBMVFC_HANDLE_VF_WWPN capability.
Link: https://lore.kernel.org/r/20201118011104.296999-6-tyreld@linux.ibm.com
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The FC iu and response payloads are located at different offsets depending
on the ibmvfc_cmd version. This is a result of the version 2 vfcFrame
definition adding an extra 64bytes of reserved space to the structure prior
to the payloads.
Add helper routines to determine the current vfcFrame version and return a
pointer to the proper iu or response structure within that ibmvfc_cmd.
Link: https://lore.kernel.org/r/20201118011104.296999-5-tyreld@linux.ibm.com
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Testing the NPIV Login response capabilities is a long winded process of
dereferencing the vhost->login_buf->resp.capabilities field, then byte
swapping that value to host endian, and performing the bitwise test.
Currently we only ever check this in ibmvfc_cancel_all(), but follow-up
patches will need to regularly check for targetWWPN and channelization
support.
Add a helper to simplify checking various VIOS capabilities, namely
ibmvfc_check_caps().
Link: https://lore.kernel.org/r/20201118011104.296999-4-tyreld@linux.ibm.com
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce a target_wwpn field to several MADs. Its possible that a SCSI ID
of a target can change due to some fabric changes. The WWPN of the SCSI
target provides a better way to identify the target. Also, add flags for
receiving MAD versioning information and advertising client support for
targetWWPN with the VIOS. This latter capability flag will be required for
future clients capable of requesting multiple hardware queues from the host
adapter.
Link: https://lore.kernel.org/r/20201118011104.296999-3-tyreld@linux.ibm.com
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The virtual FC frame command exchanged with the VIOS is used for device
reset and command abort TMF as well as normally queued commands. When
initializing the ibmvfc_cmd there are several elements of the command that
are set the same way regardless of the command type.
Deduplicate code by moving these commonally set fields into a
initialization helper routine, namely ibmvfc_init_vfc_cmd().
Link: https://lore.kernel.org/r/20201118011104.296999-2-tyreld@linux.ibm.com
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The vfcFrame correlation field is a 64bit handle that is intended to trace
I/O operations through both the client stack and VIOS stack when the
underlying physical FC adapter supports tagging.
Tag vfcFrames with the associated ibmvfc_event pointer handle.
Link: https://lore.kernel.org/r/20201117185031.129939-3-tyreld@linux.ibm.com
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Both ibmvfc_show_host_(capabilities|npiv_version) functions retrieve values
from vhost->login_buf.resp buffer. This is the MAD response buffer from the
VIOS and as such any multi-byte non-string values are in big endian format.
Byte swap these values to host CPU endian format for better human
readability.
Link: https://lore.kernel.org/r/20201117185031.129939-1-tyreld@linux.ibm.com
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, qla2xxx, tcmu,
ibmvfc, lpfc, smartpqi, hisi_sas, qedi, qedf, mpt3sas) and minor bug
fixes. There are only three core changes: adding sense codes,
cleaning up noretry and adding an option for limitless retries.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX4YulyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishaZDAQCT7rwG
UEZYHgYkU9EX9ERVBQM0SW4mLrxf3g3P5ioJsAEAtkclCM4QsIOP+MIPjIa0EyUY
khu0kcrmeFR2YwA8zhw=
=4w4S
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"The usual driver updates (ufs, qla2xxx, tcmu, ibmvfc, lpfc, smartpqi,
hisi_sas, qedi, qedf, mpt3sas) and minor bug fixes.
There are only three core changes: adding sense codes, cleaning up
noretry and adding an option for limitless retries"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (226 commits)
scsi: hisi_sas: Recover PHY state according to the status before reset
scsi: hisi_sas: Filter out new PHY up events during suspend
scsi: hisi_sas: Add device link between SCSI devices and hisi_hba
scsi: hisi_sas: Add check for methods _PS0 and _PR0
scsi: hisi_sas: Add controller runtime PM support for v3 hw
scsi: hisi_sas: Switch to new framework to support suspend and resume
scsi: hisi_sas: Use hisi_hba->cq_nvecs for calling calling synchronize_irq()
scsi: qedf: Remove redundant assignment to variable 'rc'
scsi: lpfc: Remove unneeded variable 'status' in lpfc_fcp_cpu_map_store()
scsi: snic: Convert to use DEFINE_SEQ_ATTRIBUTE macro
scsi: qla4xxx: Delete unneeded variable 'status' in qla4xxx_process_ddb_changed
scsi: sun_esp: Use module_platform_driver to simplify the code
scsi: sun3x_esp: Use module_platform_driver to simplify the code
scsi: sni_53c710: Use module_platform_driver to simplify the code
scsi: qlogicpti: Use module_platform_driver to simplify the code
scsi: mac_esp: Use module_platform_driver to simplify the code
scsi: jazz_esp: Use module_platform_driver to simplify the code
scsi: mvumi: Fix error return in mvumi_io_attach()
scsi: lpfc: Drop nodelist reference on error in lpfc_gen_req()
scsi: be2iscsi: Fix a theoretical leak in beiscsi_create_eqs()
...
In the discovery thread, ibmvfc does a vhost->task_set++ without any lock
held. This could result in two targets getting the same cancel key, which
could have strange effects in error recovery. The actual probability of
this occurring should be extremely small, since this should all be done in
a single threaded loop from the discovery thread, but let's fix it up
anyway to be safe.
Link: https://lore.kernel.org/r/1600286999-22059-1-git-send-email-brking@linux.vnet.ibm.com
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a canister on a FS9100, or similar storage, running in NPIV mode, is
rebooted, its WWPNs will fail over to another canister. When this occurs,
we see a WWPN going away from the fabric at one N-Port ID, and, a short
time later, the same WWPN appears at a different N-Port ID. When the
canister is fully operational again, the WWPNs fail back to the original
canister. If there is any I/O outstanding to the target when this occurs,
it will result in the implicit logout the ibmvfc driver issues before
removing the rport to fail. When the WWPN then shows up at a different
N-Port ID, and we issue a PLOGI to it, the VIOS will see that it still has
a login for this WWPN at the old N-Port ID, which results in the VIOS
simulating a link down / link up sequence to the client, in order to get
the VIOS and client LPAR in sync.
The patch below improves the way we handle this scenario so as to avoid the
link bounce, which affects all targets under the virtual host adapter. The
change is to utilize the Move Login MAD, which will work even when I/O is
outstanding to the target. The change only alters the target state machine
for the case where the implicit logout fails prior to deleting the rport.
If this implicit logout fails, we defer deleting the ibmvfc_target object
after calling fc_remote_port_delete. This enables us to later retry the
implicit logout after terminate_rport_io occurs, or to issue the Move Login
request if a WWPN shows up at a new N-Port ID prior to this occurring.
This has been tested by IBM's storage interoperability team on a FS9100,
forcing the failover to occur. With debug tracing enabled in the ibmvfc
driver, we confirmed the move login was sent in this scenario and confirmed
the link bounce no longer occurred.
[mkp: fix checkpatch warnings]
Link: https://lore.kernel.org/r/1599859706-8505-1-git-send-email-brking@linux.vnet.ibm.com
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix to return error code PTR_ERR() from the error handling case instead of
0.
Link: https://lore.kernel.org/r/20200907083949.154251-1-jingxiangfeng@huawei.com
Acked-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit ed830385a2 ("scsi: ibmvfc: Avoid loss of all paths during SVC node
reboot") introduced a regression where when the client resets or re-enables
its CRQ with the hypervisor there is a chance that if the server side
doesn't issue its INIT handshake quick enough the client can issue an
Implicit Logout prior to doing an NPIV Login. The server treats this
scenario as a protocol violation and closes the CRQ on its end forcing the
client through a reset that gets the client host state and next host action
out of agreement leading to a BUG assert.
ibmvfc 30000003: Partner initialization complete
ibmvfc 30000002: Partner initialization complete
ibmvfc 30000002: Host partner adapter deregistered or failed (rc=2)
ibmvfc 30000002: Partner initialized
------------[ cut here ]------------
kernel BUG at ../drivers/scsi/ibmvscsi/ibmvfc.c:4489!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Supported: No, Unreleased kernel
CPU: 16 PID: 1290 Comm: ibmvfc_0 Tainted: G OE X 5.3.18-12-default
NIP: c00800000d84a2b4 LR: c00800000d84a040 CTR: c00800000d84a2a0
REGS: c00000000cb57a00 TRAP: 0700 Tainted: G OE X (5.3.18-12-default)
MSR: 800000000282b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 24000848 XER: 00000001
CFAR: c00800000d84a070 IRQMASK: 1
GPR00: c00800000d84a040 c00000000cb57c90 c00800000d858e00 0000000000000000
GPR04: 0000000000000000 0000000000000000 0000000000000000 00000000000000a0
GPR08: c00800000d84a074 0000000000000001 0000000000000014 c00800000d84d7d0
GPR12: 0000000000000000 c00000001ea28200 c00000000016cd98 0000000000000000
GPR16: c00800000d84b7b8 0000000000000000 0000000000000000 c00000542c706d68
GPR20: 0000000000000005 c00000542c706d88 5deadbeef0000100 5deadbeef0000122
GPR24: 000000000000000c 000000000000000b c00800000d852180 0000000000000001
GPR28: 0000000000000000 c00000542c706da0 c00000542c706860 c00000542c706828
NIP [c00800000d84a2b4] ibmvfc_work+0x3ac/0xc90 [ibmvfc]
LR [c00800000d84a040] ibmvfc_work+0x138/0xc90 [ibmvfc]
This scenario can be prevented by rejecting any attempt to send an Implicit
Logout if the client adapter is not logged in yet.
Link: https://lore.kernel.org/r/20200427214824.6890-1-tyreld@linux.ibm.com
Fixes: ed830385a2 ("scsi: ibmvfc: Avoid loss of all paths during SVC node reboot")
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix up a compiler warning introduced via 54b04c99d02e
Link: https://lore.kernel.org/r/1583159961-15903-1-git-send-email-brking@linux.vnet.ibm.com
Fixes: 54b04c99d02e ("scsi: ibmvfc: Avoid loss of all paths during SVC node reboot")
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an SVC node goes down as part of a node reboot, its WWPNs are moved to
the remaining node. When the node is back online, its WWPNs are moved
back. The result is that the WWPN moves from one NPort_ID to another, then
back again. The ibmvfc driver was forcing the old port to be removed, but
not sending an implicit logout. When the WWPN showed up at the new
location, the PLOGI failed as there was already a login established for the
old scsi id. The patch below fixes this by ensuring we always send an
implicit logout for any scsi id associated with an rport prior to calling
fc_remote_port_delete.
Link: https://lore.kernel.org/r/1582767943-16611-1-git-send-email-brking@linux.vnet.ibm.com
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates.
The only core change this time around is the addition of request
batching for virtio. Since batching requires an additional flag to
use, it should be invisible to the rest of the drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXYQE/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXs9AP4usPY5
OpMlF6OiKFNeJrCdhCScVghf9uHbc7UA6cP+EgD/bCtRgcDe1ZjOTYWdeTwvwWqA
ltWYonnv6Lg3b1f9yqI=
=jRC/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates. The
only core change this time around is the addition of request batching
for virtio. Since batching requires an additional flag to use, it
should be invisible to the rest of the drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (264 commits)
scsi: hisi_sas: Fix the conflict between device gone and host reset
scsi: hisi_sas: Add BIST support for phy loopback
scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation
scsi: hisi_sas: Remove some unused function arguments
scsi: hisi_sas: Remove redundant work declaration
scsi: hisi_sas: Remove hisi_sas_hw.slot_complete
scsi: hisi_sas: Assign NCQ tag for all NCQ commands
scsi: hisi_sas: Update all the registers after suspend and resume
scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device
scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails
scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled
scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()
scsi: hisi_sas: add debugfs auto-trigger for internal abort time out
scsi: virtio_scsi: unplug LUNs when events missed
scsi: scsi_dh_rdac: zero cdb in send_mode_select()
scsi: fcoe: fix null-ptr-deref Read in fc_release_transport
scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code
scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code
scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code
scsi: ufs: Use kmemdup in ufshcd_read_string_desc()
...
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/scsi/ibmvscsi/ibmvfc.c: In function 'ibmvfc_npiv_login_done':
drivers/scsi/ibmvscsi/ibmvfc.c:4022:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
ibmvfc_retry_host_init(vhost);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/ibmvscsi/ibmvfc.c:4023:2: note: here
case IBMVFC_MAD_DRIVER_FAILED:
^~~~
drivers/scsi/ibmvscsi/ibmvfc.c: In function 'ibmvfc_bsg_request':
drivers/scsi/ibmvscsi/ibmvfc.c:1830:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
port_id = (bsg_request->rqst_data.h_els.port_id[0] << 16) |
~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
(bsg_request->rqst_data.h_els.port_id[1] << 8) |
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
bsg_request->rqst_data.h_els.port_id[2];
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/ibmvscsi/ibmvfc.c:1833:2: note: here
case FC_BSG_RPT_ELS:
^~~~
drivers/scsi/ibmvscsi/ibmvfc.c:1838:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
port_id = (bsg_request->rqst_data.h_ct.port_id[0] << 16) |
~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
(bsg_request->rqst_data.h_ct.port_id[1] << 8) |
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
bsg_request->rqst_data.h_ct.port_id[2];
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/ibmvscsi/ibmvfc.c:1841:2: note: here
case FC_BSG_RPT_CT:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No change to functionality. Simply make transport event messages a little
clearer, and rework CRQ format enums such that we have separate enums for
INIT messages and XPORT events.
[mkp: typo]
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Status and error codes are returned in big endian from the VIOS. The values
are translated into a human readable format when logged, but the values are
also logged. This patch byte swaps those values so that they are consistent
between BE and LE platforms.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The VIOS uses the SCSI_ERROR class to report PRLI failures. These errors
are indicated with the combination of a IBMVFC_FC_SCSI_ERROR return status
and 0x8000 error code. Add these codes to cmd_status[] with appropriate
human readable error message.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The text of messages logged with ibmvfc_log_error() always contain the term
"failed". In the case of cancelled commands during EH they are reported
back by the VIOS using error codes. This can be confusing to somebody
looking at these log messages as to whether a command was successfully
cancelled. The following real log message for example it is unclear if the
transaction was actaully cancelled.
<6>sd 0:0:1:1: Cancelling outstanding commands.
<3>sd 0:0:1:1: [sde] Command (28) failed: transaction cancelled (2:6) flags: 0 fcp_rsp: 0, resid=0, scsi_status: 0
Remove prefixing of "failed" to all error logged messages. The
ibmvfc_log_error() function translates the returned error/status codes to a
human readable message already.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This will make subsequent refactoring easier to handle.
Note: this patch is nowhere checkpatch clean.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Following an RSCN, ibmvfc will issue an ADISC to determine if the
underlying target has changed, comparing the SCSI ID, WWPN, and WWNN to
determine how to handle the rport in discovery. However, the comparison
of the WWPN and WWNN was performing a memcmp between a big endian field
against a CPU endian field, which resulted in the wrong answer on LE
systems. This was observed as unexpected errors getting logged at boot
time as targets were getting relogins when not needed.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix removes unneeded semicolons after switch blocks.
This issue was detected by using the Coccinelle software.
Signed-off-by: Christopher Díaz Riveros <chrisadr@gentoo.org>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
vio_device_id are not supposed to change at runtime. All functions
working with vio_device_id provided by <asm/vio.h> work with const
vio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we're resetting the host any remote port states will be reset
anyway, so it's pointless to wait for dev_loss_tmo during host reset.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
41937 1296 20 43253 a8f5 drivers/scsi/ibmvscsi/ibmvfc.o
File size After adding 'const':
text data bss dec hex filename
42129 1104 20 43253 a8f5 drivers/scsi/ibmvscsi/ibmvfc.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
mempool_alloc() cannot fail when passed GFP_NOIO or any other gfp
setting that is permitted to sleep. So remove this pointless code.
Signed-off-by: NeilBrown <neilb@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead define the timeout behavior purely based on the host_template
eh_timed_out method and wire up the existing transport implementations
in the host templates. This also clears up the confusion that the
transport template method overrides the host template one, so some
drivers have to re-override the transport template one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fc_bsg_jobdone() and bsg_job_done() are 1:1 copies now so use the
bsg-lib one instead of the FC private implementation.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change FC drivers to use 'struct bsg_job' from bsg-lib.h instead of
'struct fc_bsg_job' from scsi_transport_fc.h and remove 'struct
fc_bsg_job'.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide fc_bsg_to_rport() helper that will become handy when we're
moving from struct fc_bsg_job to a plain struct bsg_job. Also move all
LLDDs to use the new helper.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide fc_bsg_to_shost() helper that will become handy when we're
moving from struct fc_bsg_job to a plain struct bsg_job. Also use this
little helper in the LLDDs.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export fc_bsg_jobdone so drivers can use it directly instead of doing
the round-trip via struct fc_bsg_job::job_done() and use it in the
LLDDs. That way we can also unify the interfaces of fc_bsg_jobdone and
bsg_job_done.
As we've converted all LLDDs over to use fc_bsg_jobdone() directly, we
can remove the function pointer from struct fc_bsg_job as well.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't use fc_bsg_job::request and fc_bsg_job::reply directly, but use
helper variables bsg_request and bsg_reply. This will be helpful when
transitioning to bsg-lib.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a VFC port gets unmapped in the VIOS, it may not respond with a CRQ
init complete following H_REG_CRQ. If this occurs, we can end up having
called scsi_block_requests and not a resulting unblock until the init
complete happens, which may never occur, and we end up hanging I/O
requests. This patch ensures the host action stay set to
IBMVFC_HOST_ACTION_TGT_DEL so we move all rports into devloss state and
unblock unless we receive an init complete.
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ibmvfc driver currently doesn't support FC Class 3 Error Recovery.
However, it is simply a matter of informing the VIOS that the payload
expects to use sequence level error recovery via a bit flag in the
ibmvfc_cmd structure.
This patch adds a module parameter to enable error recovery support at
boot time. When enabled the RETRY service parameter bit is set during
PRLI, and ibmvfc_cmd->flags includes the IBMVFC_CLASS_3_ERR bit.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The READ FCP_XFER_READY DISABLED bit is required to always be set to one
since FCP-3. Set it in the service parameter page frame during process
login.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
My static checker complains that we need to unlock on this path. Seems
true.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When logging async events the scsi_id, wwpn, and node_name values are
used directly from the CRQ struct which are of type __be64. This can be
confusing to someone looking through the log on a LE system. Instead
byteswap these values to host endian prior to logging.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags. We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Since we got rid of ordered tag support in 2010 the prime use case of
switching on and off ordered tags has been obsolete. The other function
of enabling/disabling tagging entirely has only been correctly implemented
by the 53c700 driver and isn't generally useful.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.
Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow a driver to ask for block layer tags by setting .use_blk_tags in the
host template, in which case it will always see a valid value in
request->tag, similar to the behavior when using blk-mq. This means even
SCSI "untagged" commands will now have a tag, which is especially useful
when using a host-wide tag map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Unless we want to build a SPI tag message we should just check SCMD_TAGGED
instead of reverse engineering a tag type through the use of
scsi_populate_tag_msg.
Also rename the function to spi_populate_tag_msg, make it behave like the
other spi message helpers, and move it to the spi transport class.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Most drivers use exactly the same implementation, so provide it as a
library function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Added big endian annotations to relevant data structure fields, and necessary
byte swappings to support little endian builds.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now that we're using 64-bit LUNs internally we need to increase
the size of max_luns to 64 bits, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This fixes an issue seen with devices getting marked offline
in a scenario where a VIOS was getting rebooted while a
client VFC adapter is in SCSI EH and prevents unnecessary
EH escalation in some scenarios.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adds support for a new VIOS feature that allows ibmvfc to
optimize terminate_rport_io by telling the VIOS the target
is no longer accessible on the fabric and that it should
not send an ABTS out on the fabric to the device.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If attempting to abort requests due to a fail fail timeout
or error handling while the link is down, we cannot send
an abort out on the fabric. We can, however, send a cancel
to the VIOS. This fixes ibmvfc to send a cancel in this
case to prevent error handling from failing and/or
escalating.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adds support for receiving FAST_IO_FAIL from fc_block_scsi_eh
when in error recovery. This fixes cases of devices being
taken offline when they are no longer accessible on the fabric,
preventing them from coming back online when the fabric recovers.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The flags on a cancel operation are intended to indicate what,
if any, TMF will follow the cancel request. This fixes a case
where we were incorrectly setting the abort task set flag on
the cancel flag when we were cancelling an abort task set.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
