Except for card->read_cmd, every cmd we issue now passes through
qeth_send_control_data() and allocates a qeth_reply struct. The way we
use this struct requires additional refcounting, and pointer tracking.
Clean up things by moving most of qeth_reply's content into the main
cmd struct. This keeps things in one place, saves us the additional
refcounting and simplifies the overall code flow.
A nice little benefit is that we can now match incoming replies against
the pending requests themselves, without caching the requests' seqnos.
The qeth_reply struct stays around for a little bit longer in a shrunk
form, to avoid touching every single callback.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an cmd IO completes in qeth_irq(), calculate how much data was
processed by the device and pass this value to the cmd's callback.
This allows cmds that retrieve data from the device to check whether
sufficient data was received, so we do that in qeth_read_conf_data_cb().
Suggested-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings (Building: s390):
drivers/s390/net/ctcm_fsms.c: In function ‘ctcmpc_chx_attnbusy’:
drivers/s390/net/ctcm_fsms.c:1703:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (grp->changed_side == 1) {
^
drivers/s390/net/ctcm_fsms.c:1707:2: note: here
case MPCG_STATE_XID0IOWAIX:
^~~~
drivers/s390/net/ctcm_mpc.c: In function ‘ctc_mpc_alloc_channel’:
drivers/s390/net/ctcm_mpc.c:358:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (callback)
^
drivers/s390/net/ctcm_mpc.c:360:2: note: here
case MPCG_STATE_XID0IOWAIT:
^~~~
drivers/s390/net/ctcm_mpc.c: In function ‘mpc_action_timeout’:
drivers/s390/net/ctcm_mpc.c:1469:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if ((fsm_getstate(rch->fsm) == CH_XID0_PENDING) &&
^
drivers/s390/net/ctcm_mpc.c:1472:2: note: here
default:
^~~~~~~
drivers/s390/net/ctcm_mpc.c: In function ‘mpc_send_qllc_discontact’:
drivers/s390/net/ctcm_mpc.c:2087:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (grp->estconnfunc) {
^
drivers/s390/net/ctcm_mpc.c:2092:2: note: here
case MPCG_STATE_FLOWC:
^~~~
drivers/s390/net/qeth_l2_main.c: In function ‘qeth_l2_process_inbound_buffer’:
drivers/s390/net/qeth_l2_main.c:328:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (IS_OSN(card)) {
^
drivers/s390/net/qeth_l2_main.c:337:3: note: here
default:
^~~~~~~
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
The cast type currently gets selected in .ndo_start_xmit, and is then
piped through several layers until it's stored into the HW header.
Push the selection down into qeth_l?_fill_header() to (1) reduce the
number of xmit-wide parameters, and (2) merge the two route validation
checks into just one.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
De-duplicate the pm callback implementations from the two sub-drivers,
replacing them with core helpers that delegate to the .set_online and
.set_offline callbacks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all cmds are dynamically allocated, the code for static cmd
buffers can go away entirely. Resulting in a nice reduction of
code/data size & complexity, while removing the risk that
qeth_clear_cmd_buffers() releases cmds that are still in-flight.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VNICC code is somewhat quirky in that it defers the whole cmd setup
to a common helper qeth_l2_vnicc_request(). Some of the cmd specifics
are then passed in via parameter, while others are simply hard-coded.
Split the whole machinery up into the usual format: one helper that
allocates the cmd & fills in the common fields, while all the cmd
originators take care of their sub-cmd type specific work.
This makes it much easier to calculate the cmd's precise length, and
reduces code complexity.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the adapter, assist and bridgeport cmd paths to
dynamic allocation. Most of the work is about re-organizing the cmd
headers, calculating the correct cmd length, and filling in the right
value in the sub-cmd's length field.
Since we now also set the correct length for cmds that are not reflected
by a fixed struct (ie SNMP), we can remove the work-around from
qeth_snmp_command().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces the usage of the write channel's static cmd buffers,
by dynamically allocating all simple IPA cmds (eg. STARTLAN, SETVMAC).
It also converts the OSN path.
Doing so requires some changes to how we calculate the cmd length.
Currently when building IPA cmds, we're quite generous in how much data
we send down to the device (basically the size of the biggest cmd we
know). This is no real concern at the moment, since the static cmd
buffers are backed with zeroed pages. But for dynamic allocations, the
exact length matters. So this patch also adds the needed length
calculations to each cmd path.
Commands that have multiple subtypes (eg. SETADP) of differing length
will be converted with follow-up patches.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We statically allocate 8 cmd buffers on the read channel, when the only
IO left that's still using them is the long-running READ.
Replace this with a single allocated cmd, that gets restarted whenever
the READ completed.
This introduces refcounting for allocated cmds, so that the READ cmd can
survive the IO completion.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each cmd buffer maintains a pointer to the IO channel that it was/will
be issued on. So when dealing with cmd buffers, we don't need to pass
around a separate channel pointer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vast majority of SETUP-classified trace entries can be moved to
their device-specific trace file. This reduces pollution of the global
SETUP file, and provides a consistent trace view of all activity on the
device.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OSN currently provides a custom code path to submit IPA cmds, without
waiting for the cmd response. Replace it with qeth_send_ipa_cmd(), which
uses the common qeth_send_control_data() IO infrastructure.
By setting a custom iob->callback, we can now provide feedback to the
caller about whether the cmd has been successfully submitted to HW.
Since the callback then immediately wakes up the reply-waiter object, we
maintain the old behaviour of returning early without waiting for the
response.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The basic MPC initialization sequence is strictly sequential, and
waiting for an available cmd buffer should never be necessary.
So this change only affects the OSN path, where dangling waiters on an
unbounded wait_event() are not desirable. Switch to qeth_get_buffers(),
and let OSN callers deal with -ENOMEM.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the tear down sequence in qeth_l?_stop_card() has finished, the
card is guaranteed to be in DOWN state and we don't have to check for
it again.
With this insight we can also remove the redundant setting of
card->state in qeth_l?_set_online()'s error path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling sysfs attribute bridge_hostnotify triggers a series of udev events
for the MAC addresses of all currently connected peers. In case no VLAN is
set for a peer, the device reports the corresponding MAC addresses with
VLAN ID 4096. This currently results in attribute VLAN=4096 for all
non-VLAN interfaces in the initial series of events after host-notify is
enabled.
Instead, no VLAN attribute should be reported in the udev event for
non-VLAN interfaces.
Only the initial events face this issue. For dynamic changes that are
reported later, the device uses a validity flag.
This also changes the code so that it now sets the VLAN attribute for
MAC addresses with VID 0. On Linux, no qeth interface will ever be
registered with VID 0: Linux kernel registers VID 0 on all network
interfaces initially, but qeth will drop .ndo_vlan_rx_add_vid for VID 0.
Peers with other OSs could register MACs with VID 0.
Fixes: 9f48b9db9a ("qeth: bridgeport support - address notifications")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This de-duplicates the L2 and L3 cast-type code, and makes the L2 code
a bit more robust by removing the fragile assumption that skb->data
always points to the Ethernet Header. This would break in code paths
where we pushed the HW header onto the skb.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QETH_MAX_BUFFER_ELEMENTS() macro effectively returns a constant
value. To avoid some redundant pointer chasing and computations in the
xmit hot path, cache this value in the queue struct.
Take this as opportunity to shrink some of the queue struct's fields to
their appropriate value range, slightly reducing its total size.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have helper macros for all possible device types, replace all
remaining open-coded accesses to the type fields.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unclear what exact purpose this seqno may have served in the past.
But it's certainly no longer used anymore, as the following
napi_gro_receive() will straight away clear this part of the cb again.
Suggested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current xmit code only stops the txq after attempting to fill an
IO buffer that hasn't been TX-completed yet. In many-connection
scenarios, this can result in frequent rejected TX attempts, requeuing
of skbs with NETDEV_TX_BUSY and extra overhead.
Now that we have a proper 1-to-1 relation between stack-side txqs and
our HW Queues, overhaul the stop/wake logic so that the xmit code
stops the txq as needed.
Given that we might map multiple skbs into a single buffer, it's crucial
to ensure that the queue always provides an _entirely_ empty IO buffer.
Otherwise large skbs (eg TSO) might not fit into the last available
buffer. So whenever qeth_do_send_packet() first utilizes an _empty_
buffer, it updates & checks the used_buffers count.
This now ensures that an skb passed to qeth_xmit() can always be mapped
into an IO buffer, so remove all of the -EBUSY roll-back handling in the
TX path. We preserve the minimal safety-checks ("Is this IO buffer
really available?"), just in case some nasty future bug ever attempts to
corrupt an in-use buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds trivial support for multiple TX queues on OSA-style devices
(both real HW and z/VM NICs). For now we expose the driver's existing
QoS mechanism via .ndo_select_queue, and adjust the number of available
TX queues when qeth_update_from_chp_desc() detects that the
HW configuration has changed.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth has been supporting multiple HW Output Queues for a long time. But
rather than exposing those queues to the stack, it uses its own queue
selection logic in .ndo_start_xmit... with all the drawbacks that
entails.
Start off by switching IQD devices over to a proper mqs net_device,
and converting all the netdev_queue management code.
One oddity with IQD devices is the requirement to place all mcast
traffic on the _highest_ established HW queue. Doing so via
.ndo_select_queue seems straight-forward - but that won't work if only
some of the HW queues are active
(ie. when dev->real_num_tx_queues < dev->num_tx_queues), since
netdev_cap_txqueue() will not allow us to put skbs on the higher queues.
To make this work, we
1. let .ndo_select_queue() map all mcast traffic to netdev_queue 0, and
2. later re-map the netdev_queue and HW queue indices in
.ndo_start_xmit and the TX completion handler.
With this patch we default to a fixed set of 1 ucast and 1 mcast queue.
Support for dynamic reconfiguration is added at a later time.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The naming of several QDIO helpers doesn't match their actual
functionality, or the structures they operate on. Clean this up.
s/qeth_alloc_qdio_buffers/qeth_alloc_qdio_queues
s/qeth_free_qdio_buffers/qeth_free_qdio_queues
s/qeth_alloc_qdio_out_buf/qeth_alloc_output_queue
s/qeth_clear_outq_buffers/qeth_drain_output_queue
s/qeth_clear_qdio_buffers/qeth_drain_output_queues
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid concurrency issues, some parts of the cmd setup are delayed
until qeth_send_control_data() holds the IO channel's irq_pending
"lock". Rather than hard-coding those setup steps for each cmd type,
have the cmd provide a callback. This will make it easier to also issue
IDX commands via qeth_send_control_data().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers are running in process context now, so we can safely sleep
in qeth_send_control_data() while waiting for a cmd to complete.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L2 and L3 .ndo_set_rx_mode callbacks maintain an address cache
to decide which addresses have changed since the last modeset.
When the card is set offline, qeth_l?_stop_card() drains this cache.
This happens only after 1) the net_device has been detached, and
2) any pending RX modeset has completed. Consequently we can access the
cache lock-free.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
.ndo_set_rx_mode gets called in process context, but while holding the
addr_list spinlock. Which means we currently can't sleep while
re-programming the HW, and need to poll for IO completion. That's bad,
in particular since receiving the cmd response can fail silently and
we're then polling until the timeout hits.
As a first step towards eliminating the IO completion polling, run the
RX modeset from a work element and only take the addr_list lock while
updating the RX mode address cache.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the TX completion path, qeth_release_skbs() frees the completed
skbs with __skb_queue_purge(). This ends in kfree_skb(), reporting every
completed skb as dropped.
On the other hand when dropping an skb in .ndo_start_xmit, we end up
calling consume_skb()... where we should be using kfree_skb() so that
drop monitors get notified.
Switch the drop/consume logic around, and also don't accumulate dropped
packets in the tx_errors statistics.
Fixes: dc149e3764 ("s390/qeth: replace open-coded skb_queue_walk()")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HW trap and VNICC configuration is exposed via sysfs, and may have
already been modified when qeth_l?_probe_device() attempts to initialize
them. So (1) initialize the VNICC values a little earlier, and (2) don't
bother about the HW trap mode, it was already initialized before.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that qeth always uses dev_close() to shutdown the interface, we can
trust the locking and remove some custom state checks.
qeth_l?_stop_card() is no longer called for a card in UP state, so remove
the checks there too. This basically makes the UP state obsolete, so rip
out the whole thing (except for the sysfs-visible string).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It makes no difference whether we
1. manually disarm the HW trap and call the offline code with
recovery_mode == 1, or
2. call the offline code with recovery_mode == 0, and let it disarm the
HW trap for us.
So consolidate the two code paths in the suspend callback.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recovery code already runs in a kthread, we don't have to defer the
offlining further.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resetting an interface ("recovery"), qeth currently attempts to
elide the call to dev_close(). We initially only call .ndo_close to
quiesce the data path, and then offline & online the ccwgroup device.
If the reset succeeded, a call to .ndo_open then resumes the data path
along with some internal setup (dev_addr validation, RX modeset) that
dev_open() would have usually triggered.
dev_close() only gets called (via the close_dev worker) if the reset
action fails.
It's unclear whether this was initially done due to locking concerns, or
rather to execute the reset transparently. Either way, temporarily
closing the interface without dev_close() is fragile, and means we're
susceptible to various races and unexpected behaviour. For instance:
- Bypassing dev_deactivate_many() means that the qdiscs are not set to
__QDISC_STATE_DEACTIVATED. Consequently any intermittent TX completion
can wake up the txq, resulting in calls to .ndo_start_xmit while the
data path is down. We have custom state checking to detect this case
and drop such packets.
- Because the IFF_UP flag doesn't reflect the interface's actual state
during a reset, we have custom state checking in .ndo_open and
.ndo_close to guard against invalid calls.
- Considering that the reset might take a considerable amount of time
(in particular if an IO fails and we end up waiting for its timeout), we
_do_ want NETDEV_GOING_DOWN and NETDEV_DOWN events so that components
like bonding, team, bridge, macvlan, vlan, ... can take appropriate
action.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In its attempt to run only the minimal amount of tear down steps,
qeth_l2_stop_card() fails to reset the "is dev_addr registered?" flag
in some rare scenarios. But a future change to the tear down sequence
would cause us to _always_ hit this issue, so patch it up before that
code lands.
Fix it by unconditionally clearing the flag bit. This also allows us to
remove the additional cleanup step in qeth_dev_layer2_store().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting a L2 qeth device online, enable the HW trap as soon as the
control plane is available. This allows us to catch any error that
occurs during the very first commands.
In the same spirit, the offline code should disable the HW trap as the
very first step of its processing.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The offline code uses a specific RECOVER state to indicate that the
interface should be brought up when a qeth device is set online again.
Rather than having a specific card-state for this, just put it in an
internal flag bit and set the state to DOWN. When working with the
card's state transitions, this reduces the complexity quite a bit.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than special-casing OSN in a number of places, just give this
device type its own netdev_ops structure.
When setting up the OSN net_device, also skip the handling of the
various HW offloads (eg TSO). The device shouldn't be advertising any of
them, and the OSN code paths in qeth don't have support for them.
In particular RX VLAN filtering is not supported, so don't hook up those
callbacks in the netdev_ops.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accumulate per-TX queue statistics, and increase their size to 64 bit.
Don't bother with enabling/disabling the statistics, the overhead is
negligible.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Counting the number of function calls and the time spent in functions
is best left to proper tracing facilities.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This calls the existing errno translation helpers from the callbacks,
adding trivial wrappers where necessary. For cmds that have no
sophisticated errno translation, default to -EIO.
For IPA cmds with no callback, fall back to a minimal default. This is
currently being used by qeth_l3_send_setrouting().
Thus having all converted all callbacks, remove the legacy path in
qeth_send_control_data_cb().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By letting the callbacks deal with error translation, we no longer need
to pass the raw error codes back to the originator. This allows us to
slim down the callback's private data, and nicely simplifies the code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error propagation from cmd callbacks currently works in a way where
qeth_send_control_data_cb() picks the raw HW code from the response,
and the cmd's originator later translates this into an errno.
The callback itself only returns 0 ("done") or 1 ("expect more data").
This is
1. limiting, as the only means for the callback to report an internal
error is to invent pseudo HW codes (such as IPA_RC_ENOMEM), that
the originator then needs to understand. For non-IPA callbacks, we
even provide a separate field in the IO buffer metadata (iob->rc) so
the callback can pass back a return value.
2. fragile, as the originator must take care to not translate any errno
that is returned by qeth's own IO code paths (eg -ENOMEM). Also, any
originator that forgets to translate the HW codes potentially passes
garbage back to its caller. For instance, see
commit 2aa4867198 ("s390/qeth: translate SETVLAN/DELVLAN errors").
Introduce a new model where all HW error translation is done within the
callback, and the callback returns
> 0, if it expects more data (as before)
== 0, on success
< 0, with an errno
Start off with converting all callbacks to the new model that either
a) pass back pseudo HW codes, or b) have a dependency on a specific
HW error code. Also convert c) the one callback that uses iob->rc, and
d) qeth_setadpparms_change_macaddr_cb() so that it can pass back an
error back to qeth_l2_request_initial_mac() even when the cmd itself
was successful.
The old model remains supported: if the callback returns 0, we still
propagate the response's HW error code back to the originator.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to fill the IPA length fields is duplicated three times across
the driver:
1. qeth_send_ipa_cmd() sets IPA_CMD_LENGTH, which matches the defaults
in the IPA_PDU_HEADER template.
2. for OSN, qeth_osn_send_ipa_cmd() bypasses this logic and inserts the
length passed by the caller.
3. SNMP commands (that can outgrow IPA_CMD_LENGTH) have their own way
of setting the length fields, via qeth_send_ipa_snmp_cmd().
Consolidate this into qeth_prepare_ipa_cmd(), which all originators of
IPA cmds already call during setup of their cmd. Let qeth_send_ipa_cmd()
pull the length from the cmd instead of hard-coding IPA_CMD_LENGTH.
For now, the SNMP code still needs to fix-up its length fields manually.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Work for Bridgeport events is currently placed on a driver-wide
workqueue. If the card is removed and freed while any such work is still
active, this causes a use-after-free.
So put the events on a per-card queue, where we can control their
lifetime. As we also don't want stale events to last beyond an
offline & online cycle, flush this queue when setting the card offline.
Fixes: b4d72c08b3 ("qeth: bridgeport support - basic control")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A card's close_dev work is scheduled on a driver-wide workqueue. If the
card is removed and freed while the work is still active, this causes a
use-after-free.
So make sure that the work is completed before freeing the card.
Fixes: 0f54761d16 ("qeth: Support VEPA mode")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For recovery purposes, qeth keeps track of all registered VIDs. Replace
this by using the infrastructure introduced in
commit 9daae9bd47 ("net: Call add/kill vid ndo on vlan filter feature toggling").
By managing NETIF_F_HW_VLAN_CTAG_FILTER as a hw_feature,
netdev_update_features() will select it from dev->wanted_features
and replay all of the netdevice's VIDs to its ndo_vlan_rx_add_vid()
callback.
z/VM NICs strictly require VLAN registration, so don't expose it as
hw_feature there but add a little hack in qeth_enable_hw_features()
to make things work regardless.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a qeth card is offline, it has no connection to the HW. So none of
our control callbacks can run IO against it, and we can only cache the
input (eg a new MAC address) without providing proper feedback to the
caller. In this context, it seems much more reasonable to simply detach
the netdevice and let the kernel reject any interaction with it.
This also makes all sorts of internal state checks and locking obsolete.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-order the code flow a bit so that all initial HW setup is done before
putting the netdevice into play. For a netdevice that hasn't been
registered before, we also don't need to re-enable its HW features or
check for recovery actions.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At best this is redundant, at worst it papers over a race in the
offline / online code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 4789a21880 ("s390/qeth: fix race when setting MAC address")
resolved a race where our initial programming of dev_addr into the HW
and a call to ndo_set_mac_address() could run concurrently. In this
case, we could end up getting confused about which address was actually
set in the HW.
The quick fix was to introduce additional locking that blocks any
ndo_set_mac_address() while the device is being set online. But the race
primarily originated from the fact that we first register the netdevice,
and only then program its dev_addr. By re-ordering this sequence,
userspace will only be able to change the MAC address _after_ we have
finished with setting the initial dev_addr.
Still, the same MAC address race can also occur during a subsequent call
to qeth_l2_set_online(). So keep around the locking for now, until a
follow-up patch fully resolves this.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L2 and L3 code for these ops is almost identical, we only need to
provide a custom ndo_validate_addr() for L2 that checks whether
programming the MAC address succeeded.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass extack together with NETDEV_PRE_UP notifications, it's
necessary to route the extack to __dev_open() from diverse (possibly
indirect) callers. One prominent API through which the notification is
invoked is dev_open().
Therefore extend dev_open() with and extra extack argument and update
all users. Most of the calls end up just encoding NULL, but bond and
team drivers have the extack readily available.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-implement the card-by-RDEV lookup by using device model concepts, and
remove the now redundant list of all qeth card instances in the system.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, READ MAC on a Layer2 OSD device returns the adapter's
burnt-in MAC address. Given the default scenario of many virtual devices
on the same adapter, qeth can't make any use of this address and
therefore skips the READ MAC call for this device type.
But in some configurations, the READ MAC command for a Layer2 OSD device
actually returns a pre-provisioned, virtual MAC address. So enable the
READ MAC code to detect this situation, and let the L2 subdriver
call READ MAC for OSD devices.
This also removes the QETH_LAYER2_MAC_READ flag, which protects L2
devices against calling READ MAC multiple times. Instead protect the
whole call to qeth_l2_request_initial_mac().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the carrier 'on' for an unregistered netdevice doesn't update
its operstate. Fix this by delaying the update until the netdevice has
been registered.
Fixes: 91cc98f51e ("s390/qeth: remove duplicated carrier state tracking")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth only registers its netdevice when the qeth device is first set
online. Thus a device that has never been set online will trigger
a WARN ("network todo 'hsi%d' but state 0") in unregister_netdev() when
removed.
Fix this by protecting the unregister step, just like we already protect
against repeated registering of the netdevice.
Fixes: d3d1b205e8 ("s390/qeth: allocate netdevice early")
Reported-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Documentation/s390/s390dbf.txt states quite clearly, using any
pointer in sprinf-formatted s390dbf debug entries is dangerous.
The pointers are dereferenced whenever the trace file is read from.
So if the referenced data has a shorter life-time than the trace file,
any read operation can result in a use-after-free.
So rip out all hazardous use of indirect data, and replace any usage of
dev_name() and such by the Bus ID number.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for the new HW header id, this works just like TSO6 on L3 devices
and reuses all the existing data path support in qeth_xmit().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdevice is always available, apply any carrier state changes to it
without caching them.
On a STARTLAN event (ie. carrier-up), defer updating the state to
qeth_core_hardsetup_card() in the subsequent recovery action.
Also remove the carrier-state checks from the xmit routines. Stopping
transmission on carrier-down is the responsibility of upper-level code
(eg see dev_direct_xmit()).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. tracing iob->rc makes no sense when it hasn't been modified by the
callback,
2. the qeth_dbf_list is declared with LIST_HEAD, which also initializes
the list,
3. the ccwgroup core only calls the thaw/restore callbacks if the gdev
is online, so we don't have to check for it again.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device initialization code usually first loads a subdriver
(via qeth_core_load_discipline()), and then runs its setup() callback.
If this fails, it rolls back the load via qeth_core_free_discipline().
qeth_core_free_discipline() expects the options.layer attribute to be
initialized, but on error in setup() that's currently not the case.
Resulting in misbalanced symbol_put() calls.
Fix this by setting options.layer when loading the subdriver.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the raw values are fixed due to their use in a sysfs attribute,
we can still use the proper QETH_DISCIPLINE_* enum within the driver.
Also move the initialization into qeth_set_initial_options(), along with
all other user-configurable fields.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For quite a lot of code paths it's obvious that they will never run in
IRQ context. So replace their spin_lock_irqsave() calls with
spin_lock_irq().
While at it, get rid of the redundant card pointer in struct qeth_reply
that was used by qeth_send_control_data() to access the card's lock.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling napi_schedule() from process context does not ensure that the
NET_RX softirq is run in a timely fashion. So trigger it manually.
This is no big issue with current code. A call to ndo_open() is usually
followed by a ndo_set_rx_mode() call, and for qeth this contains a
spin_unlock_bh(). Except for OSN, where qeth_l2_set_rx_mode() bails out
early.
Nevertheless it's best to not depend on this behaviour, and just fix
the issue at its source like all other drivers do. For instance see
commit 83a0c6e589 ("i40e: Invoke softirqs after napi_reschedule").
Fixes: a1c3ed4c9c ("qeth: NAPI support for l2 and l3 discipline")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restructure the OSN xmit path to handle misaligned HW headers properly,
without shifting the packet data around.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add all the necessary TSO plumbing to the copy-less transmit path.
This includes calculating the right length of required protocol headers,
and always building a separate buffer element for the TSO headers.
A follow-up patch will then switch TSO traffic over to this path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the last remaining user of qeth_get_elements_no() to
qeth_count_elements(), so this helper can be removed.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need the exact same transmit path for non-offload-eligible traffic on
L3 OSAs. So make it accessible from both sub-drivers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For inbound data with an unsupported HW header format, only dump the
actual HW header. We have no idea how much payload follows it, and what
it contains. Worst case, we dump past the end of the Inbound Buffer and
access whatever is located next in memory.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating the main qeth_card struct with GFP_DMA blocks us from moving
it into netdev_priv(). But the only reason why we need DMA memory is the
ccw1 structs embedded into each ccw channel. So extract those into
separate allocations, like we already do for the cmd buffers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where possible use accessor macros and local pointers to access the ccw
channels. This makes it less likely to miss a spot.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the L2 OSA xmit path so that it also supports L2 IQD devices
(in particular, their HW header requirements). This allows IQD devices
to advertise NETIF_F_SG support, and eliminates the allocation overhead
for the HW header.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some transmit modes require that the HW header is located in the same
page as the initial protocol headers in skb->data. Let callers specify
the size of this contiguous header range, and enforce it when building
the HW header.
While at it, apply some gentle renaming to the relevant L2 code so that
it matches the L3 code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking whether an skb needs to be linearized to fit into an IO
buffer, it's desirable to consider the skb's final size and layout
(ie. after the HW header was added). But a subsequent linearization can
then cause the re-positioned HW header to violate its alignment
restrictions.
Dealing with this situation in two different code paths is quite tricky.
This patch integrates a) linearize-check and b) HW header construction
into one 3 step-sequence:
1. evaluate how the HW header needs to be added (to identify if it takes
up an additional buffer element), then
2. check if the required buffer elements exceed the device's limit.
Linearize when necessary and re-evaluate the HW header placement.
3. Add the HW header in the best-possible way:
a) push, without taking up an additional buffer element
b) push, but consume another buffer element
c) allocate a header object from the cache.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nowadays an skb fragment typically spans over multiple pages. So replace
the obsolete, SG-only 'fragments' counter with one that tracks the
consumed buffer elements. This is what actually matters for performance.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth's ndo_change_mtu() only applies some trivial bounds checking. Set
up dev->min_mtu properly, so that dev_set_mtu() can do this for us.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the MPC initialization code discovers the HW-specific max MTU,
apply the resulting changes straight to the netdevice.
If this is the device's first initialization, also set its MTU
(HiperSockets: the max MTU; else: a layer-specific default value).
Then cap the current MTU by the new max MTU.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocation of the netdevice is currently delayed until a qeth card first
goes online. This complicates matters in several places, where we need
to cache values instead of applying them straight to the netdevice.
Improve on this by moving the allocation up to where the qeth card
itself is created. This is also one step in direction of eventually
placing the qeth card into netdev_priv().
In all subsequent code, remove the now redundant checks whether
card->dev is valid.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some redundant EXPORTs. While at it, also move some L2-only
prototypes into the proper header file.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate duplicated code, fix the misuse of RTN_UNSPEC and simplify
the handling of non-unicast traffic on IQD devices.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing a device's address lists (or its promisc mode) already triggers
an RX modeset, there's no need to do it manually from the L2 driver's
ndo_vlan_rx_kill_vid() hook.
Also when setting a device online, dev_open() already calls
dev_set_rx_mode(). So a manual modeset is only necessary from the
recovery path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit e830baa9c3 ("qeth: restore device features after recovery") and
commit ce34435641 ("s390/qeth: rely on kernel for feature recovery")
made sure that the HW functions for device features get re-programmed
after recovery.
But we missed that the same handling is also required when a card is
first set offline (destroying all HW context), and then online again.
Fix this by moving the re-enable action out of the recovery-only path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*ether_addr*_64bits functions have been introduced to optimize
performance critical paths, which access 6-byte ethernet address as u64
value to get "nice" assembly. A harmless hack works nicely on ethernet
addresses shoved into a structure or a larger buffer, until busted by
Kasan on smth like plain (u8 *)[6].
qeth_l2_set_mac_address calls qeth_l2_remove_mac passing
u8 old_addr[ETH_ALEN] as an argument.
Adding/removing macs for an ethernet adapter is not that performance
critical. Moreover is_multicast_ether_addr_64bits itself on s390 is not
faster than is_multicast_ether_addr:
is_multicast_ether_addr(%r2) -> %r2
llc %r2,0(%r2)
risbg %r2,%r2,63,191,0
is_multicast_ether_addr_64bits(%r2) -> %r2
llgc %r2,0(%r2)
risbg %r2,%r2,63,191,0
So, let's just use is_multicast_ether_addr instead of
is_multicast_ether_addr_64bits.
Fixes: bcacfcbc82 ("s390/qeth: fix MAC address update sequence")
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When qeth_l2_set_mac_address() finds the card in a non-reachable state,
it merely copies the new MAC address into dev->dev_addr so that
__qeth_l2_set_online() can later register it with the HW.
But __qeth_l2_set_online() may very well be running concurrently, so we
can't trust the card state without appropriate locking:
If the online sequence is past the point where it registers
dev->dev_addr (but not yet in SOFTSETUP state), any address change needs
to be properly programmed into the HW. Otherwise the netdevice ends up
with a different MAC address than what's set in the HW, and inbound
traffic is not forwarded as expected.
This is most likely to occur for OSD in LPAR, where
commit 21b1702af1 ("s390/qeth: improve fallback to random MAC address")
now triggers eg. systemd to immediately change the MAC when the netdevice
is registered with a NET_ADDR_RANDOM address.
Fixes: bcacfcbc82 ("s390/qeth: fix MAC address update sequence")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If READ MAC fails to fetch a valid MAC address, allow some more device
types (IQD and z/VM OSD) to fall back to a random address.
Also use eth_hw_addr_random(), for indicating to userspace that the
address type is NET_ADDR_RANDOM.
Note that while z/VM has various protection schemes to prohibit
custom addresses on its NICs, they are all optional. So we should at
least give it a try.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if a qeth device supports IPv6 RX checksum offload, and hook it up
into the existing NETIF_F_RXCSUM support.
As NETIF_F_RXCSUM is now backed by a combination of HW Assists, we need
to be a little smarter when dealing with errors during a configuration
change:
- switching on NETIF_F_RXCSUM only makes sense if at least one HW Assist
was enabled successfully.
- for switching off NETIF_F_RXCSUM, all available HW Assists need to be
deactivated.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if a qeth device supports IPv6 TX checksum offload, and advertise
NETIF_F_IPV6_CSUM accordingly. Add support for setting the relevant bits
in IPv6 packet descriptors.
Currently this has only limited use (ie. UDP, or Jumbo Frames). For any
TCP traffic with a standard MSS, the TCP checksum gets calculated
as part of the linear GSO segmentation.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This consolidates the checksum offload code that was duplicated
over the two qeth subdrivers.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct net_device contains a dev_port field. Store the OSA port number
in this field.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the vid_list is only accessed from process context, there's no need to
protect it with a spinlock.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both qeth sub drivers use the same QDIO queue handlers, there's no need
to expose them via the driver's discipline. No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Submitting a cmd IO request (usually on the WRITE device, but for IDX
also on the READ device) is currently done with ccw_device_start()
and a manual timeout in the caller.
On timeout, the caller cleans up the related resources (eg. IO buffer).
But 1) the IO might still be active and utilize those resources, and
2) when the IO completes, qeth_irq() will attempt to clean up the
same resources again.
Instead of introducing additional resource locking, switch to
ccw_device_start_timeout() to ensure IO termination after timeout, and
let the IRQ handler alone deal with cleaning up after a request.
This also removes a stray write->irq_pending reset from
clear_ipacmd_list(). The routine doesn't terminate any pending IO on
the WRITE device, so this should be handled properly via IO timeout
in the IRQ handler.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing the MAC address on a L2 qeth device, current code first
unregisters the old address, then registers the new one.
If HW rejects the new address (or the IO fails), the device ends up with
no operable address at all.
Re-order the code flow so that the old address only gets dropped if the
new address was registered successfully. While at it, add logic to catch
some corner-cases.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing couple of duplicate includes, found by "make includecheck".
That leaves 1 duplicate include in arch/s390/kernel/entry.S, which is
there for a reason (it includes generated asm/syscall_table.h twice).
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On removal, a qeth card's netdevice is currently not properly freed
because the call chain looks as follows:
qeth_core_remove_device(card)
lx_remove_device(card)
unregister_netdev(card->dev)
card->dev = NULL !!!
qeth_core_free_card(card)
if (card->dev) !!!
free_netdev(card->dev)
Fix it by free'ing the netdev straight after unregistering. This also
fixes the sysfs-driven layer switch case (qeth_dev_layer2_store()),
where the need to free the current netdevice was not considered at all.
Note that free_netdev() takes care of the netif_napi_del() for us too.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
init_qdio_queues() resets the Input Queue's overall QDIO state, and
positions the buffer cursor back to 0. So this is the obvious place to
also reset the queue's NAPI context (in contrast to doing it rather
randomly in the middle of the big set_online() path).
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newly-allocated skbs default to PACKET_HOST, and eth_type_trans() is
smart enough to determine any other packet type from the frame's
destination address.
So except for the IQD sniffer case, there is no need to set up
skb->pkt_type manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_alloc_skb() doesn't need to disable IRQs during the allocation,
and thus may save us a few cycles.
Doing so requires a small fix-up in the HiperTransport path, which
currently assumes a fixed NET_SKB_PAD headroom padding. napi_alloc_skb()
adds an additional NET_IP_ALIGN padding, so use the proper helper for
setting up the mac_header offset.
Use this opportunity to convert the non-NAPI path to netdev_alloc_skb(),
which means that skb->dev is now always set-up during allocation and
doesn't need to be assigned manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth implements HW-based Unicast Filtering (via SETVMAC) on L2 devices.
Tell the stack, so it knows that receiving traffic for secondary
addresses doesn't require full-blown promiscuous mode.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_SG support is currently limited to OSA (and for L2 even OSD)
devices. Advertise it for some more device types (OSM, L2 OSX, z/VM OSA)
that share the same code paths. For now, keep it switched off by
default on these devices.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"s390/qeth: fix SETIP command handling" introduced a new helper, apply
it driver-wide.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once all of qeth_l3_set_rx_mode()'s single-use helpers are folded back
in, the two implementations actually look quite similar. So improve the
readability by converting both set_rx_mode() routines to a common
format.
This also allows us to walk ip_mc_htable just once, instead of three
times.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be a little more self-documenting, and get rid of OSA_ADDR_LEN.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For adding/removing a MAC address, use just one helper each that
handles both unicast and multicast.
Saves one level of indirection for multicast addresses, while improving
the error reporting for unicast addresses.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of tracking the uc/mc state in each MAC address object, just
check the multicast bit in the address itself.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Various TCP control block fixes, including one that crashes with
SELinux, from David Ahern and Eric Dumazet.
2) Fix ACK generation in rxrpc, from David Howells.
3) ipvlan doesn't set the mark properly in the ipv4 route lookup key,
from Gao Feng.
4) SIT configuration doesn't take on the frag_off ipv4 field
configuration properly, fix from Hangbin Liu.
5) TSO can fail after device down/up on stmmac, fix from Lars Persson.
6) Various bpftool fixes (mostly in JSON handling) from Quentin Monnet.
7) Various SKB leak fixes in vhost/tun/tap (mostly observed as
performance problems). From Wei Xu.
8) mvpps's TX descriptors were not zero initialized, from Yan Markman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tcp: use IPCB instead of TCP_SKB_CB in inet_exact_dif_match()
tcp: add tcp_v4_fill_cb()/tcp_v4_restore_cb()
rxrpc: Fix the MAINTAINERS record
rxrpc: Use correct netns source in rxrpc_release_sock()
liquidio: fix incorrect indentation of assignment statement
stmmac: reset last TSO segment size after device open
ipvlan: Add the skb->mark as flow4's member to lookup route
s390/qeth: build max size GSO skbs on L2 devices
s390/qeth: fix GSO throughput regression
s390/qeth: fix thinko in IPv4 multicast address tracking
tap: free skb if flags error
tun: free skb in early errors
vhost: fix skb leak in handle_rx()
bnxt_en: Fix a variable scoping in bnxt_hwrm_do_send_msg()
bnxt_en: fix dst/src fid for vxlan encap/decap actions
bnxt_en: wildcard smac while creating tunnel decap filter
bnxt_en: Need to unconditionally shut down RoCE in bnxt_shutdown
phylink: ensure we take the link down when phylink_stop() is called
sfp: warn about modules requiring address change sequence
sfp: improve RX_LOS handling
...
The current GSO skb size limit was copy&pasted over from the L3 path,
where it is needed due to a TSO limitation.
As L2 devices don't offer TSO support (and thus all GSO skbs are
segmented before they reach the driver), there's no reason to restrict
the stack in how large it may build the GSO skbs.
Fixes: d52aec97e5 ("qeth: enable scatter/gather in layer 2 mode")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using GSO with small MTUs currently results in a substantial throughput
regression - which is caused by how qeth needs to map non-linear skbs
into its IO buffer elements:
compared to a linear skb, each GSO-segmented skb effectively consumes
twice as many buffer elements (ie two instead of one) due to the
additional header-only part. This causes the Output Queue to be
congested with low-utilized IO buffers.
Fix this as follows:
If the MSS is low enough so that a non-SG GSO segmentation produces
order-0 skbs (currently ~3500 byte), opt out from NETIF_F_SG. This is
where we anticipate the biggest savings, since an SG-enabled
GSO segmentation produces skbs that always consume at least two
buffer elements.
Larger MSS values continue to get a SG-enabled GSO segmentation, since
1) the relative overhead of the additional header-only buffer element
becomes less noticeable, and
2) the linearization overhead increases.
With the throughput regression fixed, re-enable NETIF_F_SG by default to
reap the significant CPU savings of GSO.
Fixes: 5722963a8e ("qeth: do not turn on SG per default")
Reported-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/s390/net/ files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Instead of silently discarding VLAN registration requests on OSM,
just indicate that this card type doesn't support VLAN.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no reason why l2_set_mac_address() should ever be called for
a netdevice that's not owned by qeth. It's certainly not required for
VLAN devices, which have their own netdev_ops.
Also:
1) we don't do such validation for any of the other netdev_ops routines.
2) the code in question clearly has never been actually exercised;
it's broken. After determining that the device is not owned
by qeth, it would still use dev->ml_priv to write a qeth trace entry.
Remove the check, and its helper that walked the global card list.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly return any error encountered during VLAN processing to the
the caller.
Resulting change in behaviour: if SETVLAN fails while registering a
new VLAN ID, the stack no longer creates the corresponding vlan device.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locking the output queue prior to TX is needed on OSA devices,
to synchronize against a packing flush from the TX completion code
(via qeth_check_outbound_queue()).
But send_packet_fast() is only used for IQDs, which don't do packing.
So remove the locking, and apply some easy cleanups.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HiperSockets allow configuring so called VNIC Characteristics (VNICC)
that influence how the underlying hardware handles packets. For VNICCs,
additional commands for getting and setting timeouts are available.
Currently, the learning VNICC uses these commands.
* Learning VNICC: If learning is enabled on a qeth device, the device
learns the source MAC addresses of outgoing packets and incoming
packets to those learned MAC addresses are received.
For learning, the timeout specifies the idle period in seconds, after
which the underlying hardware removes a learned MAC address again.
This patch adds support for the IPA commands that are required to get
and set the current timeout values for the learning VNIC characteristic.
Also, it introduces the sysfs interface that allows users to configure
the timeout.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HiperSocket devices allow enabling and disabling so called VNIC
Characteristics (VNICC) that influence how the underlying hardware
handles packets. These VNICCs are:
* Flooding VNICC: Flooding allows specifying if packets to unknown
destination MAC addresses are received by the qeth device.
* Multicast flooding VNICC: Multicast flooding allows specifying if
packets to multicast MAC addresses are received by the qeth device.
* Learning VNICC: If learning is enabled on a qeth device, the device
learns the source MAC addresses of outgoing packets and incoming
packets to those learned MAC addresses are received.
* Takeover setvmac VNICC: If takeover setvmac is configured on a qeth
device, the MAC address of this device can be configured on a
different qeth device with the setvmac IPA command.
* Takeover by learning VNICC: If takeover learning is enabled on a qeth
device, the MAC address of this device can be learned (learning VNICC)
on a different qeth device.
* BridgePort invisible VNICC: If BridgePort invisible is enabled on a
qeth device, (1) packets from this device are not sent to a BridgePort
enabled qeth device and (2) packets coming from a BridgePort enabled
qeth device are not received by this device.
* Receive broadcast VNICC: Receive broadcast allows configuring if a
qeth device receives packets with the broadcast destination MAC
address.
This patch adds support for the IPA commands that are required to enable
and disable these VNIC characteristics on qeth devices. As a
prerequisite, it also adds the query commands IPA command.
The query commands IPA command allows requesting the supported commands
for each characteristic from the underlying hardware.
Additionally, this patch provides users with a sysfs user interface to
enable/disable the VNICCs mentioned above.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VNIC Characteristics (VNICC) are features of HiperSockets that define
how packets are handled by the underlying network hardware. For example,
if the VNICC flooding is configured on a qeth device, ethernet frames to
unknown destination MAC addresses are received.
Currently, there is support for seven VNICCs: flooding, multicast
flooding, receive broadcast, learning, takeover learning, takeover
setvmac, bridge invisible. Also, six IPA commands exist for configuring
VNICCs on a qeth device: query characteristics, query commands, enable
characteristic, disable characteristic, set timeout, get timeout.
This patch adds the basic code infrastructure for VNICC support to qeth.
It allows querying VNICC support from the underlying hardware. To this
end, it adds:
* basic message formats for IPA commands
* basic data structures
* basic error handling
* query characteristics IPA command support
The query characteristics IPA command allows requesting the currently
supported and currently enabled VNIC characteristics from the underlying
hardware.
Support for the other IPA commands and for the configuration of VNICCs
is added in follow-up patches together with the respective user
interface functions.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking a full copy via skb_realloc_headroom() on every xmit is overkill
and wastes CPU time; all we actually need is to push on the qeth_hdr.
So rework the L2 OSA TX path to avoid the copy.
Minor complications arise because struct qeth_hdr must not cross a page
boundary. So add a new helper qeth_push_hdr() that catches this, and
falls back to the hdr cache that we already use for IQDs.
This change uncovered that qeth's TX completion takes rather long.
Now that we no longer free the original skb straight away and thus call
skb->destructor later than before, throughput regresses significantly.
For now, restore old behaviour by adding an explicit skb_orphan(),
and a big TODO to improve the TX completion time.
Tested-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a prerequisite for unifying the code to build header elements.
The TSO header has a different size, so we can no longer rely on implicitly
adding the size of a normal qeth_hdr.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TSO we need to skip the skb's qeth/IP/TCP headers when mapping
it into buffer elements. Instead of (mis)using skb_pull(), pass a
corresponding offset to fill_buffer() like we already do for IQDs.
No actual change in the resulting TSO buffers.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO code already calculates the length of its header element,
no need to duplicate this in the low-level code again.
Use this opportunity to make hd_len unsigned, and for TSO match
its calculation to what tso_fill_header() does.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IQD we already need to fix up the qeth_hdr's length field, and
future changes will require more flexibility for OSA as well. The
device-specific path knows best what header length it requires, so just
pass it from there.
While at it, remove the unused qeth_card parameter.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2_hard_start_xmit() actually doesn't contain much shared code,
and having device-specific paths makes isolated changes a lot easier.
So split it into three routines for IQD, OSN and OSD/OSM/OSX.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidation of duplicated code, no functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up the inline cruft in s390 net drivers. Many of the inlined
functions had only one caller anyway.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some open-coded parts with their proper API calls.
Also remove two skb_[re]set_mac_header() calls in the L2
xmit paths that are clearly no longer required, since at least
commit 6d1ccff627 ("net: reset mac header in dev_start_xmit()").
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_l2_request_initial_mac() queries the device for its supported
adapterparms, even though they already have been queried as part of the
device's high-level setup. Remove that extra call.
The only call chain for qeth_l2_request_initial_mac() is
__qeth_l2_set_online()
qeth_core_hardsetup_card()
qeth_query_setadapterparms()
qeth_l2_setup_netdev()
qeth_l2_request_initial_mac()
qeth_query_setadapterparms()
, and we only reach qeth_l2_request_initial_mac() if the first
adapterparms query succeeds. Hence removing the second query results in
no loss of functionality.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After transmitting a skb via send_packet[_fast](), the statistics
code accesses the skb once more to account for transmitted page frags.
This has a (theoretical?) race against the TX completion - if the TX
completion is processed and frees the skb before hard_start_xmit()
gets to the statistics part, we access random memory.
Fix this by caching the # of page frags, before the skb is transmitted.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a s390 guest runs on a z/VM host that's part of a SSI cluster,
it can be migrated to a different host. In this case, the MAC address
it originally obtained on the old host may be re-assigned to a new
guest. This would result in address conflicts between the two guests.
When running as z/VM guest, use the diag26c MAC Service to obtain
a hypervisor-managed MAC address. The MAC Service is SSI-aware, and
won't re-assign the address after the guest is migrated to a new host.
This patch adds support for the z/VM MAC Service on L2 devices.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add ipa return codes for Bridgeport (HiperSockets and OSA) according to
system level design.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridgeport is a l2-specific feature, and we should write its
capabilities to a debug entry.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access card->dev only after checking whether's its valid.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b4d72c08b3 ("qeth: bridgeport support - basic control")
broke the support for OSM and OSN devices as follows:
As OSM and OSN are L2 only, qeth_core_probe_device() does an early
setup by loading the l2 discipline and calling qeth_l2_probe_device().
In this context, adding the l2-specific bridgeport sysfs attributes
via qeth_l2_create_device_attributes() hits a BUG_ON in fs/sysfs/group.c,
since the basic sysfs infrastructure for the device hasn't been
established yet.
Note that OSN actually has its own unique sysfs attributes
(qeth_osn_devtype), so the additional attributes shouldn't be created
at all.
For OSM, add a new qeth_l2_devtype that contains all the common
and l2-specific sysfs attributes.
When qeth_core_probe_device() does early setup for OSM or OSN, assign
the corresponding devtype so that the ccwgroup probe code creates the
full set of sysfs attributes.
This allows us to skip qeth_l2_create_device_attributes() in case
of an early setup.
Any device that can't do early setup will initially have only the
generic sysfs attributes, and when it's probed later
qeth_l2_probe_device() adds the l2-specific attributes.
If an early-setup device is removed (by calling ccwgroup_ungroup()),
device_unregister() will - using the devtype - delete the
l2-specific attributes before qeth_l2_remove_device() is called.
So make sure to not remove them twice.
What complicates the issue is that qeth_l2_probe_device() and
qeth_l2_remove_device() is also called on a device when its
layer2 attribute changes (ie. its layer mode is switched).
For early-setup devices this wouldn't work properly - we wouldn't
remove the l2-specific attributes when switching to L3.
But switching the layer mode doesn't actually make any sense;
we already decided that the device can only operate in L2!
So just refuse to switch the layer mode on such devices. Note that
OSN doesn't have a layer2 attribute, so we only need to special-case
OSM.
Based on an initial patch by Ursula Braun.
Fixes: b4d72c08b3 ("qeth: bridgeport support - basic control")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting up the device from within the layer discipline's
probe routine, creating the layer-specific sysfs attributes can fail.
Report this error back to the caller, and handle it by
releasing the layer discipline.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
[jwi: updated commit msg, moved an OSN change to a subsequent patch]
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
get_settings() is deprecated and lacks support for higher link
speeds, so implement get_link_ksettings() instead.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. a buffer has 16 is_header flags, because that's its # of elements
2. replace the last occurrence of QETH_HEADER_SIZE, and remove it
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_start_xmit() expects us to return netdev_tx_t here...
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'elements_needed' is not used in qeth_do_send_packet_fast(),
so consequently remove it.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Duplicated code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Identical code, we just need to call a layer-specific hook
to process any received buffer.
qeth_buffer_reclaim_work() is shuffled around to avoid a
forward declaration for qeth_queue_input_buffer().
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a number of layer-independent ioctls that we can handle
in core, and reduce code duplication. For layer-specific ioctls,
add a do_ioctl() discipline hook.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. options.add_hhlen is set but never used, drop it
2. clean up no longer required forward declarations
3. delete all sorts of unused defines
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the device type, hard_start_xmit() builds different output
buffer formats. For instance with HiperSockets, on both L2 and L3 we
strip the ETH header from the skb - L3 doesn't need it, and L2 carries
it in the buffer's header element.
For this, we pass data_offset = ETH_HLEN all the way down to
__qeth_fill_buffer(), where skb->data is then adjusted accordingly.
But the initial size calculation still considers the *full* skb length
(including the ETH header). So qeth_get_elements_no() can erroneously
reject a skb as too big, even though it would actually fit into an
output buffer once the ETH header has been trimmed off later.
Fix this by passing an additional offset to qeth_get_elements_no(),
that indicates where in the skb the on-wire data actually begins.
Since the current code uses data_offset=-1 for some special handling
on OSA, we need to clamp data_offset to 0...
On HiperSockets this helps when sending ~MTU-size skbs with weird page
alignment. No change for OSA or AF_IUCV.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
STARTLAN needs to be the first IPA command after MPC initialization
completes.
So move the qeth_send_startlan() call from the layer disciplines
into the core path, right after the MPC handshake.
While at it, replace the magic LAN OFFLINE return code
with the existing enum.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
