With module test, there is error dump:
------------[ cut here ]------------
notifier callback pca9450_i2c_restart_handler already registered
WARNING: kernel/notifier.c:23 at notifier_chain_register+0x5c/0x88,
CPU#0: kworker/u16:3/50
Call trace:
notifier_chain_register+0x5c/0x88 (P)
atomic_notifier_chain_register+0x30/0x58
register_restart_handler+0x1c/0x28
pca9450_i2c_probe+0x418/0x538
i2c_device_probe+0x220/0x3d0
really_probe+0x114/0x410
__driver_probe_device+0xa0/0x150
driver_probe_device+0x40/0x114
__device_attach_driver+0xd4/0x12c
So use devm_register_sys_off_handler to let kernel handle the resource
free to avoid kernel dump.
Fixes: 6157e62b07 ("regulator: pca9450: Add restart handler")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://patch.msgid.link/20250815-pca9450-v1-1-7748e362dc97@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Previous commit 548d770c33 ("regulator: pca9450: Add support for mode
operations") added support for setting forced PWM mode on the buck
regulators for pca9450a and pca9450bc parts. However part pca9451a also
supports this feature, thus add support for it.
Fixes: 548d770c33 ("regulator: pca9450: Add support for mode operations")
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Link: https://patch.msgid.link/20250618063339.2508893-1-primoz.fiser@norik.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the PWM mode on the buck controllers configurable from
devicetree. Some boards require forced PWM mode to keep the supply
ripple within acceptable limits under light load conditions.
Signed-off-by: Martijn de Gouw <martijn.de.gouw@prodrive-technologies.com>
Link: https://patch.msgid.link/20250525071823.819342-2-martijn.de.gouw@prodrive-technologies.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When restarting a CPU powered by the PCA9450 power management IC, it
is beneficial to use the PCA9450 to power cycle the CPU and all its
connected peripherals to start up in a known state. The PCA9450 features
a cold start procedure initiated by an I2C command.
Add a restart handler so that the PCA9450 is used to restart the CPU.
The restart handler sends command 0x14 to the SW_RST register,
initiating a cold reset (Power recycle all regulators except LDO1, LDO2
and CLK_32K_OUT)
As the PCA9450 is a PMIC specific for the i.MX8M family CPU, the restart
handler priority is set just slightly higher than imx2_wdt and the PSCI
restart handler. This makes sure this restart handler takes precedence.
Signed-off-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
Link: https://patch.msgid.link/20250505115936.1946891-1-paul.geurts@prodrive-technologies.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are two ways to set the output voltage of the LD05
regulator. First by writing to the voltage selection registers
and second by toggling the SD_VSEL signal.
Usually board designers connect SD_VSEL to the VSELECT signal
controlled by the USDHC controller, but in some cases the
signal is hardwired to a fixed low level (therefore selecting
3.3V as initial value for allowing to boot from the SD card).
In these cases, the voltage is only determined by the value
of the LDO5CTRL_L register. Introduce a property
nxp,sd-vsel-fixed-low to let the driver know that SD_VSEL
is low and there is no GPIO to actually get that
information from dynamically.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://patch.msgid.link/20250303132258.50204-1-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The SD_VSEL GPIO is fetched twice for no reason. Remove the
duplicate code.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://patch.msgid.link/20250219080152.11883-1-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The LDO5 regulator has two configuration registers, but only
LDO5CTRL_L contains the bits for enabling/disabling the regulator.
Fixes: 0935ff5f1f ("regulator: pca9450: add pca9450 pmic driver")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://patch.msgid.link/20241218152842.97483-6-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
For LDO5 we need to be able to check the status of the SD_VSEL input in
order to know which control register is used. Read the status of the
SD_VSEL signal via GPIO and use the correct register accordingly.
To use this, the LDO5 node in the devicetree needs the sd-vsel-gpios
property to reference the GPIO that is used to read back the SD_VSEL
status internally. Please note that the SION bit in the IOMUX must be
set if the signal is muxed as VSELECT and controlled by the USDHC
controller.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://patch.msgid.link/20241218152842.97483-5-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 8c67a11bae.
It turns out that all boards using the PCA9450 actually have the
SD_VSEL input connected to the VSELECT signal of the SoCs SD/MMC
interface or use a fixed level.
The assumptions on which this was implemented were wrong. There
is no need for a GPIO-only-based approach and keeping this will
cause confusion and lead people to implement non-standard setups.
All in-tree users of this have been migrated and we can savely
remove this now and allow for a more future-proof approach
of syncing the actual status of SD_VSEL and the PMIC driver.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://patch.msgid.link/20241218152842.97483-4-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the PMIC pca9452 support, which add ldo3 compared with pca9451a.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20241205-pca9450-v1-4-aab448b74e78@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set 'enable_value' in the regulator descriptor for different bucks to
manage their enable modes:
- 00b: OFF
- 01b: ON when PMIC_ON_REQ = H
- 10b: ON when PMIC_ON_REQ = H && PMIC_STBY_REQ = L
- 11b: Always ON
Ensure appropriate behavior based on the intended design. For example:
- Buck2, designed for vddarm, should be set to '10b' (ON when
PMIC_STBY_REQ = L) since it can be off when `PMIC_STBY_REQ = H` after the
kernel enters suspend.
- Other bucks remain '01b' (ON when PMIC_ON_REQ = H), matching the default
setting. This avoids the need to re-enable them during kernel boot as they
are already enabled after PMIC initialization.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20241205-pca9450-v1-1-aab448b74e78@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The IRQ line might not be connected on some boards. Allow the driver
to be probed without it.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://patch.msgid.link/20240708084107.38986-5-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Bo Liu <liubo03@inspur.com>:
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Bo Liu (13):
regulator: da9121: convert to use maple tree register cache
regulator: da9211: convert to use maple tree register cache
regulator: isl9305: convert to use maple tree register cache
regulator: max8973: convert to use maple tree register cache
regulator: mt6311: convert to use maple tree register cache
regulator: pca9450: convert to use maple tree register cache
regulator: pf8x00: convert to use maple tree register cache
regulator: pfuze100: convert to use maple tree register cache
regulator: rtmv20: convert to use maple tree register cache
regulator: rtq6752: convert to use maple tree register cache
regulator: tps51632: convert to use maple tree register cache
regulator: tps62360: convert to use maple tree register cache
regulator: rpi-panel-attiny: convert to use maple tree register cache
drivers/regulator/da9121-regulator.c | 4 ++--
drivers/regulator/da9211-regulator.c | 2 +-
drivers/regulator/isl9305.c | 2 +-
drivers/regulator/max8973-regulator.c | 2 +-
drivers/regulator/mt6311-regulator.c | 2 +-
drivers/regulator/pca9450-regulator.c | 2 +-
drivers/regulator/pf8x00-regulator.c | 2 +-
drivers/regulator/pfuze100-regulator.c | 2 +-
drivers/regulator/rpi-panel-attiny-regulator.c | 2 +-
drivers/regulator/rtmv20-regulator.c | 2 +-
drivers/regulator/rtq6752-regulator.c | 2 +-
drivers/regulator/tps51632-regulator.c | 2 +-
drivers/regulator/tps62360-regulator.c | 2 +-
13 files changed, 14 insertions(+), 14 deletions(-)
--
2.18.2
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Link: https://msgid.link/r/20240320085740.4604-7-liubo03@inspur.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714174930.4063320-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes a copy & paste error.
No functional change intended, BUCK1_ENMODE_MASK equals BUCK2_ENMODE_MASK.
Fixes: 0935ff5f1f ("regulator: pca9450: add pca9450 pmic driver")
Originally-from: Robin Gong <yibin.gong@nxp.com
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de
Link: https://lore.kernel.org/r/20230512081935.2396180-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Link: https://lore.kernel.org/r/20230505220218.1239542-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org
This follows on the change ("regulator: Set PROBE_PREFER_ASYNCHRONOUS
for drivers that existed in 4.14") but changes regulators didn't exist
in Linux 5.4 but did exist in Linux 5.10.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.4.I01f21c98901641a009890590ddc1354c0f294e5e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-553-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When DVS is enabled via the devicetree properties
"nxp,dvs-run-voltage" and "nxp,dvs-standby-voltage" then
also the bit that enables DVS control via PMIC_STBY_REQ pin
should be set.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-5-rickaran@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The default configuration of the PMIC behavior makes the PMIC
power cycle most regulators on WDOG_B assertion. This power
cycling causes the memory contents of OCRAM to be lost.
Some systems neeeds some memory that survives reset and
reboot, therefore this patch is created.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-4-rickaran@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the I2C Level Translator included in PCA9450 configurable from
devicetree. The reset state is off. By setting nxp,i2c-lt-enable, the
I2C Level Translator will be enabled while in STANDBY or RUN state.
Signed-off-by: Per-Daniel Olsson <perdo@axis.com>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-2-rickaran@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver uses the DVS registers PCA9450_REG_BUCKxOUT_DVS0 to set the
voltage for the buck regulators 1, 2 and 3. This has no effect as the
PRESET_EN bit is set by default and therefore the preset values are used
instead, which are set to 850 mV.
To fix this we clear the PRESET_EN bit at time of initialization.
Fixes: 0935ff5f1f ("regulator: pca9450: add pca9450 pmic driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210222115229.166620-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes the return value of pca9450_i2c_probe() to use the correct
error code when getting the sd-vsel GPIO fails.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210222150809.208942-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
By default the PCA9450 doesn't handle the assertion of the WDOG_B
signal, but this is required to guarantee that things like software
resets triggered by the watchdog work reliably.
As we don't want to rely on the bootloader to enable this, we tell
the PMIC to issue a cold reset in case the WDOG_B signal is
asserted (WDOG_B_CFG = 10), just as the NXP U-Boot code does.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210211105534.38972-3-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
LDO5 has two separate control registers. LDO5CTRL_L is used if the
input signal SD_VSEL is low and LDO5CTRL_H if it is high.
The current driver implementation only uses LDO5CTRL_H. To make this
work on boards that have SD_VSEL connected to a GPIO, we add support
for specifying an optional GPIO and setting it to high at probe time.
In the future we might also want to add support for boards that have
SD_VSEL set to a fixed low level. In this case we need to change the
driver to be able to use the LDO5CTRL_L register.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210211105534.38972-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usages of these is to assign their address to the ops field in
the regulator_desc struct, which is a const pointer. Make them const to
allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200913084114.8851-5-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
