With the recent rework of the PCI power control code, the workaround for
the wlan-enable GPIO - where we don't set a default (low) state in the
power sequencing driver, but instead request the pin as-is - should no
longer be needed but some platforms still fail to probe the WLAN
controller. This is caused by the Qcom PCIe controller and needs a
workaround in the controller driver so add a FIXME to eventually remove
the hack from this driver once this is done.
Link: https://lore.kernel.org/r/20250102121530.26993-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Enable support for controlling the power-up sequence of the PMU inside
the WCN6750 model.
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Link: https://lore.kernel.org/r/20241209103455.9675-5-quic_janathot@quicinc.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
WCN6855 (also known as QCA6490) is similar to the already supported
QCA6390 but takes in two more supplies so add a new vregs list for it.
On sm8450-hdk it also requires a short assert of the xo-clk pin so add
handling for it in a dedicated unit.
As we now have a separate set of targets for this variant, store the
pointer to the targets struct associated with a model in the device
match data.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241018-sc8280xp-pwrseq-v6-2-8da8310d9564@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
- add support for the new PMU variant inside the WCN6855 chipset
- add documentation for the subsystem
-----BEGIN PGP SIGNATURE-----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=u9Ea
-----END PGP SIGNATURE-----
Merge tag 'pwrseq-updates-for-v6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull power sequencing updates from Bartosz Golaszewski:
"There's one change adding support for a new PMU model and another
adding documentation for the subsystem which probably should have been
part of the initial commit but better late than never:
- add support for the new PMU variant inside the WCN6855 chipset
- add documentation for the subsystem"
* tag 'pwrseq-updates-for-v6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
Documentation: add a driver API doc for the power sequencing subsystem
power: sequencing: qcom-wcn: add support for the WCN6855 PMU
Commit a9aaf1ff88 ("power: sequencing: request the WLAN enable GPIO
as-is") broke WLAN on boards on which the wlan-enable GPIO enabling the
wifi module isn't in output mode by default. We need to set direction to
output while retaining the value that was already set to keep the ath
module on if it's already started.
Fixes: a9aaf1ff88 ("power: sequencing: request the WLAN enable GPIO as-is")
Link: https://lore.kernel.org/r/20240823115500.37280-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Enable support for controlling the power-up sequence of the PMU inside
the WCN6855 model.
Signed-off-by: Konrad Dybcio <konradybcio@kernel.org>
[Bartosz: split Konrad's bigger patch, write the commit message]
Co-developed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240813190841.155067-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
If the WCN module is powered up before linux boots and the ath11k driver
probes at the same time as the power sequencing driver, we may end up
driving the wlan-enable GPIO low in the latter, breaking the start-up of
the WLAN module. Request the wlan-enable GPIO as-is so that if the WLAN
module is already starting/started, we leave it alone.
Fixes: 2f1630f437 ("power: pwrseq: add a driver for the PMU module on the QCom WCN chipsets")
Reported-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20240813190751.155035-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This adds the power sequencing driver for the PMU modules present on the
Qualcomm WCN Bluetooth and Wifi chipsets. It uses the pwrseq subsystem
and knows how to match the sequencer to the consumer device by verifying
the relevant properties and DT layout. Using this driver will allow the
BT and WLAN drivers to respect the required delays between enabling the
two modules.
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD, SM8650-QRD & SM8650-HDK
Tested-by: Caleb Connolly <caleb.connolly@linaro.org> # OnePlus 8T
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240605123850.24857-3-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
