The SPMI based PMICs have the HIGH and LOW GPIO output strength mappings
interchanged, fix them.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Link: https://lore.kernel.org/r/20220912210624.4527-3-quic_amelende@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for SPMI PMIC GPIO subtypes GPIO_LV_VIN2 and
GPIO_MV_VIN3.
GPIO_LV_VIN2 GPIOs support two input reference voltages: VIN0 and
VIN1. These are typically connected to 1.8 V and 1.2 V supplies
respectively.
GPIO_MV_VIN3 GPIOs support three input reference voltages: VIN0,
VIN1, and VIN2. These are typically connected to Vph, 1.8 V, and
1.2 V supplies respectively.
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Link: https://lore.kernel.org/r/20220912210624.4527-2-quic_amelende@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irqchip implementation used inside the gpiochips are not supposed to
be changed during runtime. So let's make the one inside the spmi-gpio
gpiochip immutable.
This fixes the below warning during boot:
gpio gpiochip0: (c440000.spmi:pmic@0:gpio@c000): not an immutable chip, please consider fixing it!
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220830092232.168561-1-manivannan.sadhasivam@linaro.org
[switched two lines as indicated by Johan]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver to support pin configuration for LPASS
(Low Power Audio SubSystem) LPI (Low Power Island) pinctrl
on SC8280XP.
This IP is an additional pin control block for Audio Pins on top the
existing SoC Top level pin-controller.
Hardware setup looks like:
TLMM GPIO[189 - 207] --> LPASS LPI GPIO [0 - 18]
This pin controller has some similarities compared to Top level
msm SoC Pin controller like 'each pin belongs to a single group'
and so on. However this one is intended to control only audio
pins in particular, which can not be configured/touched by the
Top level SoC pin controller except setting them as gpios.
Apart from this, slew rate is also available in this block for
certain pins which are connected to SLIMbus or SoundWire Bus.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220817113747.9111-3-srinivas.kandagatla@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver to support pin configuration for LPASS
(Low Power Audio SubSystem) LPI (Low Power Island) pinctrl
on SM8450.
This IP is an additional pin control block for Audio Pins on top the
existing SoC Top level pin-controller.
Hardware setup looks like:
TLMM GPIO[165 - 187] --> LPASS LPI GPIO [0 - 22]
This pin controller has some similarities compared to Top level
msm SoC Pin controller like 'each pin belongs to a single group'
and so on. However this one is intended to control only audio
pins in particular, which can not be configured/touched by the
Top level SoC pin controller except setting them as gpios.
Apart from this, slew rate is also available in this block for
certain pins which are connected to SLIMbus or SoundWire Bus.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220817113833.9625-3-srinivas.kandagatla@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin numbers for UFS_RESET and SDC2_* are not
consistent in the pinctrl driver for sc8180x.
So fix it.
Signed-off-by: Molly Sophia <mollysophia379@gmail.com>
Fixes: 97423113ec ("pinctrl: qcom: Add sc8180x TLMM driver")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220807122645.13830-3-mollysophia379@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently in the wakeirq_map, gpio36 and gpio37 have the same wakeirq
number, resulting in gpio37 being unable to trigger interrupts.
It looks like that this is a typo in the wakeirq map. So fix it.
Signed-off-by: Molly Sophia <mollysophia379@gmail.com>
Fixes: 97423113ec ("pinctrl: qcom: Add sc8180x TLMM driver")
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220807122645.13830-2-mollysophia379@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Add PINCTRL_PINGROUP() helper macro (and use it in the AMD driver).
New drivers:
- Intel Meteor Lake support.
- Reneasas RZ/V2M and r8a779g0 (R-Car V4H).
- AXP209 variants AXP221, AXP223 and AXP809.
- Qualcomm MSM8909, PM8226, PMP8074 and SM6375.
- Allwinner D1.
Improvements:
- Proper pin multiplexing in the AMD driver.
- Mediatek MT8192 can use generic drive strength and pin
bias, then fixes on top plus some I2C pin group fixes.
- Have the Allwinner Sunplus SP7021 use the generic DT schema and
make interrupts optional.
- Handle Qualcomm SC7280 ADSP.
- Handle Qualcomm MSM8916 CAMSS GP clock muxing.
- High impedance bias on ZynqMP.
- Serialize StarFive access to MMIO.
- Immutable gpiochip for BCM2835, Ingenic, Qualcomm SPMI GPIO.
-----BEGIN PGP SIGNATURE-----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=enmk
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Outside the pinctrl driver and DT bindings we hit some Arm DT files,
patched by the maintainers.
Other than that it is business as usual.
Core changes:
- Add PINCTRL_PINGROUP() helper macro (and use it in the AMD driver).
New drivers:
- Intel Meteor Lake support.
- Reneasas RZ/V2M and r8a779g0 (R-Car V4H).
- AXP209 variants AXP221, AXP223 and AXP809.
- Qualcomm MSM8909, PM8226, PMP8074 and SM6375.
- Allwinner D1.
Improvements:
- Proper pin multiplexing in the AMD driver.
- Mediatek MT8192 can use generic drive strength and pin bias, then
fixes on top plus some I2C pin group fixes.
- Have the Allwinner Sunplus SP7021 use the generic DT schema and
make interrupts optional.
- Handle Qualcomm SC7280 ADSP.
- Handle Qualcomm MSM8916 CAMSS GP clock muxing.
- High impedance bias on ZynqMP.
- Serialize StarFive access to MMIO.
- Immutable gpiochip for BCM2835, Ingenic, Qualcomm SPMI GPIO"
* tag 'pinctrl-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (117 commits)
dt-bindings: pinctrl: qcom,pmic-gpio: add PM8226 constraints
pinctrl: qcom: Make PINCTRL_SM8450 depend on PINCTRL_MSM
pinctrl: qcom: sm8250: Fix PDC map
pinctrl: amd: Fix an unused variable
dt-bindings: pinctrl: mt8186: Add and use drive-strength-microamp
dt-bindings: pinctrl: mt8186: Add gpio-line-names property
ARM: dts: imxrt1170-pinfunc: Add pinctrl binding header
pinctrl: amd: Use unicode for debugfs output
pinctrl: amd: Fix newline declaration in debugfs output
pinctrl: at91: Fix typo 'the the' in comment
dt-bindings: pinctrl: st,stm32: Correct 'resets' property name
pinctrl: mvebu: Missing a blank line after declarations.
pinctrl: qcom: Add SM6375 TLMM driver
dt-bindings: pinctrl: Add DT schema for SM6375 TLMM
dt-bindings: pinctrl: mt8195: Use drive-strength-microamp in examples
Revert "pinctrl: qcom: spmi-gpio: make the irqchip immutable"
pinctrl: imx93: Add MODULE_DEVICE_TABLE()
pinctrl: sunxi: Add driver for Allwinner D1
pinctrl: sunxi: Make some layout parameters dynamic
pinctrl: sunxi: Refactor register/offset calculation
...
All the many other configs depend on config PINCTRL_MSM, yet for config
PINCTRL_SM8450 we select config PINCTRL_MSM. Make config PINCTRL_SM8450
depend on PINCTRL_MSM to be consistent with the rest.
Signed-off-by: John Garry <john.garry@huawei.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/1658829764-124936-1-git-send-email-john.garry@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a driver to control the TLMM block on SM6375. This is an adapted
version of msm-5.4's pinctrl-blair driver.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20220716192900.454653-2-konrad.dybcio@somainline.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpiolib is unique in the way it uses intermediate fwspecs
when feeding an interrupt specifier to the parent domain, as it
relies on the populate_parent_alloc_arg() callback to perform
a dynamic allocation.
This is pretty inefficient (we free the structure almost immediately),
and the only reason this isn't a stack allocation is that our
ThunderX friend uses MSIs rather than a FW-constructed structure.
Let's solve it by providing a new type composed of the union
of a struct irq_fwspec and a msi_info_t, which satisfies both
requirements. This allows us to use a stack allocation, and we
can move the handful of users to this new scheme.
Also perform some additional cleanup, such as getting rid of the
stub versions of the irq_domain_translate_*cell helpers, which
are never used when CONFIG_IRQ_DOMAIN_HIERARCHY isn't selected.
Tested on a Tegra186.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Daniel Palmer <daniel@thingy.jp>
Cc: Romain Perier <romain.perier@gmail.com>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Robert Richter <rric@kernel.org>
Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220707182314.66610-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Commit 6c846d026d ("gpio: Don't fiddle with irqchips marked as
immutable") added a warning to indicate if the gpiolib is altering the
internals of irqchips.
Following this change the following warning is now observed for the SPMI
PMIC pinctrl driver:
gpio gpiochip1: (200f000.spmi:pmic@0:gpio@c000): not an immutable chip, please consider fixing it!
Fix this by making the irqchip in the SPMI PMIC pinctrl driver immutable.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20220624195112.894916-1-robimarko@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the compilation error, caused by updating constant variable.
Hence remove redundant constant variable, which is no more useful
as per new design.
The issue is due to some unstaged changes. Fix it up.
Fixes: 36fe26843d ("pinctrl: qcom: sc7280: Add clock optional check for ADSP bypass targets")
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1656489290-20881-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The idea was right but the code was breaking in next.
I assume some unstaged commit was involed. Fix it up.
Cc: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Fixes: 36fe26843d ("pinctrl: qcom: sc7280: Add clock optional check for ADSP bypass targets")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO 31, 32 can be muxed to GCC_CAMSS_GP(1,2)_CLK respectively but the
function was never assigned to the pingroup (even though the function
exists already).
Add this mode to the related pins.
Fixes: 5373a2c5ab ("pinctrl: qcom: Add msm8916 pinctrl driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220612145955.385787-4-nikita@trvn.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update lpass lpi pin control driver, with clock optional check for ADSP
disabled platforms. This check required for distingushing ADSP based
platforms and ADSP bypass platforms.
In case of ADSP enabled platforms, where audio is routed through ADSP
macro and decodec GDSC Switches are triggered as clocks by pinctrl
driver and ADSP firmware controls them. So It's mandatory to enable
them in ADSP based solutions.
In case of ADSP bypass platforms clock voting is optional as these macro
and dcodec GDSC switches are maintained as power domains and operated from
lpass clock drivers.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1654921357-16400-3-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pm6125 has 9 GPIOs with no holes inbetween.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220511220613.1015472-4-marijn.suijten@somainline.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmJu9FYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAyEH/16xtJSpLmLwrQzG
o+4ToQxSQ+/9UHyu0RTEvHg2THm9/8emtIuYyc/5FgdoWctcSa3AaDcveWmuWmkS
KYcdhfJsaEqjNHS3OPYXN84fmo9Hel7263shu5+IYmP/sN0DfQp6UWTryX1q4B3Q
4Pdutkuq63Uwd8nBZ5LXQBumaBrmkkuMgWEdT4+6FOo1mPzwdIGBxCuz1UsNNl5k
chLWxkQfe2eqgWbYJrgCQfrVdORXVtoU2fGilZUNrHRVGkkldXkkz5clJfapyZD3
odmZCEbrE4GPKgZwCmDERMfD1hzhZDtYKiHfOQ506szH5ykJjPBcOjHed7dA60eB
J3+wdek=
=39Ca
-----END PGP SIGNATURE-----
Merge tag 'v5.18-rc5' into devel
Merge in Linux 5.18-rc5 since new code to the STM32 driver
depend in a non-trivial way on the fixes merged in -rc5.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update bulk clock voting to optional voting as ADSP bypass platform doesn't
need macro and decodec clocks, as these macro and dcodec GDSC switches are
maintained as power domains and operated from lpass clock drivers.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1650285427-19752-8-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Extract the chip specific SM8250 data from the LPASS LPI pinctrl driver
to allow reusing the common code in the addition of subsequent
platforms.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1650285427-19752-6-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Prevent gpiolib from messing with the irqchip by advertising
the irq_chip structure as immutable, making it const, and adding
the various calls that gpiolib relies upon.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220419141846.598305-8-maz@kernel.org
In other places the SDC and UFS pins have been swapped but this was
missed in the PINCTRL_PIN definitions. Fix that.
Fixes: 7d74b55afd ("pinctrl: qcom: Add SM6350 pinctrl driver")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20220318183004.858707-5-luca.weiss@fairphone.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Specify the PDC mapping for SM8150, so that gpio interrupts are
properly mapped to the wakeup IRQs of the PDC.
Cc: Maulik Shah <quic_mkshah@quicinc.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220226184028.111566-3-bhupesh.sharma@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It adds the map of wakeup capable GPIOs and the pins at MPM wake
controller on QCM2290, so that these GPIOs can wake up the SoC from
vlow/vmin low power mode.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20211122080938.20623-1-shawn.guo@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When egpio_enable bit is cleared, the gpio is driven by SSC/LPASS TLMM and
the APSS TLMM settings are ignored. Reflect that in the debugfs dump.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20220210131210.24605-2-jonathan@marek.ca
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This mirrors egpio support added for sc7280. This change is necessary for
gpios 165 to 209 to be driven by APSS.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20220210131210.24605-1-jonathan@marek.ca
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MSM GPIO IRQ controller relies on the parent IRQ controller to set the
CPU affinity for the IRQ. And this is only valid if there is any wakeup
parent available and defined in DT.
For the case of no parent IRQ controller defined in DT,
msm_gpio_irq_set_affinity() and msm_gpio_irq_set_vcpu_affinity() should
return -EINVAL instead of 0 as the affinity can't be set.
Otherwise, below warning will be printed by genirq:
genirq: irq_chip msmgpio did not update eff. affinity mask of irq 70
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20220113162617.131697-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove these assignment all at once.
For the details one may look into the of_gpio_dev_init() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211214125855.33207-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pincontrol driver for tlmm block found in SM8450 SoC
This patch is based on initial code downstream by
Elliot Berman <eberman@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211201072434.3968768-3-vkoul@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmGavnseHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGcl4H/jyFVlHDSa+utMA5
7PEQX0AarkBtSvKUgK/SivZxX06nYp2UU5L4Jn70O/mccXWo0ru82eDVO3nSImDR
Mi668IqzbYfGqVL6CMztDku+XbyT3Yr/i9QILFbLWV5DhCM422GXXN8PFBibDHdI
6Oyt1WoUh404yjVIHOCNwprfLObxREV6ARhFsIsmCRa8Hf+RkKOY5Twua6j5emm5
aamiq6SYLtf2H5+DwkR5TnPkie6I2o8oLtA7JYiJpKh5KK75qjlpzFd3S3OWsi1H
0g752g12r7tLh4ac3Xfgwf36pQ2CdiZ7NUOkJhZWT4aHPqPh+MVheQfpR41f5Sgc
pvFslTo=
=QdMf
-----END PGP SIGNATURE-----
Merge tag 'v5.16-rc2' into devel
Linux 5.16-rc2 is needed because nonurgent fixes headed
for next are strongly textually dependent on a fix that
was applied for rc2.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sc7280 supports the egpio feature, GPIOs ranging from 144 to 174
(31 GPIOs) support it, we define gpio_func to 9, which
is an unused function for all these pins on sc7280.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1637041084-3299-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
egpio is a scheme which allows special power Island Domain IOs
(LPASS,SSC) to be reused as regular chip GPIOs by muxing regular
TLMM functions with Island Domain functions.
With this scheme, an IO can be controlled both by the cpu running
linux and the Island processor. This provides great flexibility to
re-purpose the Island IOs for regular TLMM usecases.
2 new bits are added to ctl_reg, egpio_present is a read only bit
which shows if egpio feature is available or not on a given gpio.
egpio_enable is the read/write bit and only effective if egpio_present
is 1. Once its set, the Island IO is controlled from Chip TLMM.
egpio_enable when set to 0 means the GPIO is used as Island Domain IO.
To support this we add a new function 'egpio' which can be used to
set the egpio_enable to 0, for any other TLMM controlled functions
we set the egpio_enable to 1.
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1637041084-3299-1-git-send-email-rnayak@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The downstream TLMM binding covers a group of TLMM-related hardware
blocks, but the upstream binding only captures the particular block
related to controlling the TLMM pins from an OS. In the translation of
the driver from downstream, the offset of 0x100000 was lost for the UFS
and SDC pingroups.
Fixes: d5d348a327 ("pinctrl: qcom: Add SM8350 pinctrl driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20211104170835.1993686-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It has been observed that dual edge triggered wakeirq GPIOs on SDM845
doesn't trigger interrupts on the falling edge.
Enabling wakeirq_dual_edge_errata for SDM845 indicates that the PDC in
SDM845 suffers from the same problem described, and worked around, by
Doug in 'c3c0c2e18d94 ("pinctrl: qcom: Handle broken/missing PDC dual
edge IRQs on sc7180")', so enable the workaround for SDM845 as well.
The specific problem seen without this is that gpio-keys does not detect
the falling edge of the LID gpio on the Lenovo Yoga C630 and as such
consistently reports the LID as closed.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-By: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211102034115.1946036-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When PINCTRL_QCOM_SPMI_PMIC or PINCTRL_QCOM_SSBI_PMIC
is selected, and GPIOLIB is not selected, Kbuild
gives the following warnings:
WARNING: unmet direct dependencies detected for GPIOLIB_IRQCHIP
Depends on [n]: GPIOLIB [=n]
Selected by [y]:
- PINCTRL_QCOM_SPMI_PMIC [=y] && PINCTRL [=y] && (ARCH_QCOM [=n] || COMPILE_TEST [=y]) && OF [=y] && SPMI [=y]
WARNING: unmet direct dependencies detected for GPIOLIB_IRQCHIP
Depends on [n]: GPIOLIB [=n]
Selected by [y]:
- PINCTRL_QCOM_SSBI_PMIC [=y] && PINCTRL [=y] && (ARCH_QCOM [=n] || COMPILE_TEST [=y]) && OF [=y]
This is because these config options enable GPIOLIB_IRQCHIP
without selecting or depending on GPIOLIB, despite
GPIOLIB_IRQCHIP depending on GPIOLIB.
These unmet dependency bugs were detected by Kismet,
a static analysis tool for Kconfig. Please advise if this
is not the appropriate solution.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Link: https://lore.kernel.org/r/20211029004610.35131-1-julianbraha@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Add infrastructure for per-parent interrupt data to support
the Apple pin controller.
New drivers:
- New combined pin control and GPIO driver for the Apple SoC.
This is used in all modern Apple silicon such as the M1
laptops but also in at least recent iPhone variants.
- New subdriver for the Qualcomm SM6350
- New subdriver for the Qualcomm QCM2290
- New subdriver for the Qualcomm PM6350
- New subdriver for the Uniphier NX1
- New subdriver for the Samsung ExynosAutoV9
- New subdriver for the Mediatek MT7986
- New subdriver for the nVidia Tegra194
Improvements:
- Improve power management in the Mediatek driver.
- Improvements to the Renesas internal consistency checker.
- Convert the Rockchip pin control device tree bindings to YAML.
- Finally convert the Qualcomm PMIC SSBI and SPMI MPP GPIO
driver to use hierarchical interrupts.
- Convert the Qualcomm PMIC MPP device tree bindings to YAML.
-----BEGIN PGP SIGNATURE-----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=4Ms6
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"The most interesting aspect is that we now have initial support for
the Apple pin controller as used in the M1 laptops and the iPhones
which is a step forward for using Linux efficiently on this Apple
silicon.
Core changes:
- Add infrastructure for per-parent interrupt data to support the
Apple pin controller.
New drivers:
- New combined pin control and GPIO driver for the Apple SoC. This is
used in all modern Apple silicon such as the M1 laptops but also in
at least recent iPhone variants.
- New subdriver for the Qualcomm SM6350
- New subdriver for the Qualcomm QCM2290
- New subdriver for the Qualcomm PM6350
- New subdriver for the Uniphier NX1
- New subdriver for the Samsung ExynosAutoV9
- New subdriver for the Mediatek MT7986
- New subdriver for the nVidia Tegra194
Improvements:
- Improve power management in the Mediatek driver.
- Improvements to the Renesas internal consistency checker.
- Convert the Rockchip pin control device tree bindings to YAML.
- Finally convert the Qualcomm PMIC SSBI and SPMI MPP GPIO driver to
use hierarchical interrupts.
- Convert the Qualcomm PMIC MPP device tree bindings to YAML"
* tag 'pinctrl-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (55 commits)
pinctrl: add pinctrl/GPIO driver for Apple SoCs
dt-bindings: pinctrl: Add apple,npins property to apple,pinctrl
dt-bindings: pinctrl: add #interrupt-cells to apple,pinctrl
gpio: Allow per-parent interrupt data
pinctrl: tegra: Fix warnings and error
pinctrl: intel: Kconfig: Add configuration menu to Intel pin control
pinctrl: tegra: Use correct offset for pin group
pinctrl: core: fix possible memory leak in pinctrl_enable()
pinctrl: bcm2835: Allow building driver as a module
pinctrl: equilibrium: Fix function addition in multiple groups
pinctrl: tegra: Add pinmux support for Tegra194
pinctrl: tegra: include lpdr pin properties
pinctrl: mediatek: add support for MT7986 SoC
dt-bindings: pinctrl: update bindings for MT7986 SoC
pinctrl: microchip sgpio: use reset driver
dt-bindings: pinctrl: pinctrl-microchip-sgpio: Add reset binding
dt-bindings: pinctrl: qcom,pmic-mpp: switch to #interrupt-cells
pinctrl: qcom: spmi-mpp: add support for hierarchical IRQ chip
pinctrl: qcom: spmi-mpp: hardcode IRQ counts
pinctrl: qcom: ssbi-mpp: add support for hierarchical IRQ chip
...
spmi-mpp did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should be
usable from the start without the consumer having to make an additional
call to get the proper IRQ on the parent. This patch adds hierarchical
IRQ chip support to the spmi-mpp code to correct this issue.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-17-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The probing of this driver calls platform_irq_count, which will
setup all of the IRQs that are configured in device tree. In
preparation for converting this driver to be a hierarchical IRQ
chip, hardcode the IRQ count based on the hardware type so that all
the IRQs are not configured immediately and are configured on an
as-needed basis later in the boot process.
This change will also allow for the removal of the interrupts property
later in this patch series once the hierarchical IRQ chip support is in.
This patch also removes the generic qcom,spmi-mpp OF match since we
don't know the number of pins. All of the existing upstream bindings
already include the more-specific binding.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-16-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ssbi-mpp did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should be
usable from the start without the consumer having to make an additional
call to get the proper IRQ on the parent. This patch adds hierarchical
IRQ chip support to the ssbi-mpp code to correct this issue.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-15-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The probing of this driver calls platform_irq_count, which will
setup all of the IRQs that are configured in device tree. In
preparation for converting this driver to be a hierarchical IRQ
chip, hardcode the IRQ count based on the hardware type so that all
the IRQs are not configured immediately and are configured on an
as-needed basis later in the boot process.
This change will also allow for the removal of the interrupts property
later in this patch series once the hierarchical IRQ chip support is in.
This patch also removes the generic qcom,ssbi-mpp OF match since we
don't know the number of pins. All of the existing upstream bindings
already include the more-specific binding.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-14-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The
fix we agreed on in the end is to make this symbol selected by any
driver using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in v5.15.
There is a small merge conflict against an earlier partial fix for the
QCOM_SCM dependency problems.
Finally, the branch also includes a small unrelated build fix for NOMMU
architectures.
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=187C
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
Now that SCM can be a loadable module, we have to add another
dependency to avoid link failures when ipa or adreno-gpu are
built-in:
aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe':
ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available'
ld.lld: error: undefined symbol: qcom_scm_is_available
>>> referenced by adreno_gpu.c
>>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a
This can happen when CONFIG_ARCH_QCOM is disabled and we don't select
QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd
use a similar dependency here to what we have for QCOM_RPROC_COMMON,
but that causes dependency loops from other things selecting QCOM_SCM.
This appears to be an endless problem, so try something different this
time:
- CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on'
but that is simply selected by all of its users
- All the stubs in include/linux/qcom_scm.h can go away
- arm-smccc.h needs to provide a stub for __arm_smccc_smc() to
allow compile-testing QCOM_SCM on all architectures.
- To avoid a circular dependency chain involving RESET_CONTROLLER
and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement.
According to my testing this still builds fine, and the QCOM
platform selects this symbol already.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently, if the GPIO is configured as output in the bootloader
and user changes the mode to input in HLOS, it would end up
getting configured as input/output. Functionally, this is fine;
however, there may be some requirements where the output needs
to be disabled so that it can be used only for input.
Add support to enable/disable output mode through "output-enable"
or "output-disable" pinctrl properties.
Signed-off-by: Subbaraman Narayanamurthy <quic_subbaram@quicinc.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631588246-4811-3-git-send-email-quic_subbaram@quicinc.com
[Drop copyright change which is already upstrean in -rcN]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's a porting of pinctrl-scuba driver from CAF msm-4.19 kernel. The
egpio and wake bits are removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923033224.29719-3-shawn.guo@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pincontrol driver for tlmm block found in SM6350 SoC
This patch is based on downstream copyleft code.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923161450.15278-2-konrad.dybcio@somainline.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use PM suspend callbacks from msm core, without this the hog_sleep
pins don't change state in suspend.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1632389487-11283-1-git-send-email-rnayak@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the functions for QUP4 (spi, uart, uim & i2c), sdc3 and audio_pcm as
derived from the downstream gpiomux configuration.
Also sort the functions alphabetically, while we're at it.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210911232707.259615-2-luca@z3ntu.xyz
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pmic_gpio_child_to_parent_hwirq() and
gpiochip_populate_parent_fwspec_fourcell() translate a pinctrl-
spmi-gpio irqspec to an SPMI controller irqspec. When they do
this, they use a fixed SPMI slave ID of 0 and a fixed GPIO
peripheral offset of 0xC0 (corresponding to SPMI address 0xC000).
This translation results in an incorrect irqspec for secondary
PMICs that don't have a slave ID of 0 as well as for PMIC chips
which have GPIO peripherals located at a base address other than
0xC000.
Correct this issue by passing the slave ID of the pinctrl-spmi-
gpio device's parent in the SPMI controller irqspec and by
calculating the peripheral ID base from the device tree 'reg'
property of the pinctrl-spmi-gpio device.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: satya priya <skakit@codeaurora.org>
Fixes: ca69e2d165 ("qcom: spmi-gpio: add support for hierarchical IRQ chip")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1631798498-10864-2-git-send-email-skakit@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
no core changes at all this time, just driver work!
New drivers:
- New subdriver for Intel Keem Bay (an ARM-based SoC)
- New subdriver for Qualcomm MDM9607 and SM6115
- New subdriver for ST Microelectronics STM32MP135
- New subdriver for Freescale i.MX8ULP ("Ultra Low Power")
- New subdriver for Ingenic X2100
- Support for Qualcomm PMC8180, PMC8180C, SA8155p-adp PMIC GPIO
- Support Samsung Exynos850
- Support Renesas RZ/G2L
Enhancements:
- A major refactoring of the Rockchip driver, breaking part of it out
to a separate GPIO driver in drivers/gpio
- Pin bias support on Renesas r8a77995
- Add SCI pins support to Ingenic JZ4755 and JZ4760
- Mediatek device tree bindings converted to YAML
-----BEGIN PGP SIGNATURE-----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=I6N/
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.15 kernel cycle, no
core changes at all this time, just driver work!
New drivers:
- New subdriver for Intel Keem Bay (an ARM-based SoC)
- New subdriver for Qualcomm MDM9607 and SM6115
- New subdriver for ST Microelectronics STM32MP135
- New subdriver for Freescale i.MX8ULP ("Ultra Low Power")
- New subdriver for Ingenic X2100
- Support for Qualcomm PMC8180, PMC8180C, SA8155p-adp PMIC GPIO
- Support Samsung Exynos850
- Support Renesas RZ/G2L
Enhancements:
- A major refactoring of the Rockchip driver, breaking part of it out
to a separate GPIO driver in drivers/gpio
- Pin bias support on Renesas r8a77995
- Add SCI pins support to Ingenic JZ4755 and JZ4760
- Mediatek device tree bindings converted to YAML"
* tag 'pinctrl-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (53 commits)
pinctrl: renesas: Add RZ/G2L pin and gpio controller driver
pinctrl: samsung: Add Exynos850 SoC specific data
dt-bindings: pinctrl: samsung: Add Exynos850 doc
MAINTAINERS: Add maintainers for amd-pinctrl driver
pinctrl: Add Intel Keem Bay pinctrl driver
dt-bindings: pinctrl: Add bindings for Intel Keembay pinctrl driver
pinctrl: zynqmp: Drop pinctrl_unregister for devm_ registered device
dt-bindings: pinctrl: qcom-pmic-gpio: Remove the interrupts property
dt-bindings: pinctrl: qcom-pmic-gpio: Convert qcom pmic gpio bindings to YAML
dt-bindings: pinctrl: mt8195: Use real world values for drive-strength arguments
dt-bindings: mediatek: convert pinctrl to yaml
arm: dts: mt8183: Move pinfunc to include/dt-bindings/pinctrl
arm: dts: mt8135: Move pinfunc to include/dt-bindings/pinctrl
pinctrl: ingenic: Add .max_register in regmap_config
pinctrl: ingenic: Fix bias config for X2000(E)
pinctrl: ingenic: Fix incorrect pull up/down info
pinctrl: Ingenic: Add pinctrl driver for X2100.
dt-bindings: pinctrl: Add bindings for Ingenic X2100.
pinctrl: Ingenic: Add SSI pins support for JZ4755 and JZ4760.
pinctrl: Ingenic: Improve the code.
...
Core changes:
- The usual set of small fixes and improvements all over the place, but nothing
outstanding
MSI changes:
- Further consolidation of the PCI/MSI interrupt chip code
- Make MSI sysfs code independent of PCI/MSI and expose the MSI interrupts
of platform devices in the same way as PCI exposes them.
Driver changes:
- Support for ARM GICv3 EPPI partitions
- Treewide conversion to generic_handle_domain_irq() for all chained
interrupt controllers
- Conversion to bitmap_zalloc() throughout the irq chip drivers
- The usual set of small fixes and improvements
-----BEGIN PGP SIGNATURE-----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=qyll
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2021-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates to the interrupt core and driver subsystems:
Core changes:
- The usual set of small fixes and improvements all over the place,
but nothing stands out
MSI changes:
- Further consolidation of the PCI/MSI interrupt chip code
- Make MSI sysfs code independent of PCI/MSI and expose the MSI
interrupts of platform devices in the same way as PCI exposes them.
Driver changes:
- Support for ARM GICv3 EPPI partitions
- Treewide conversion to generic_handle_domain_irq() for all chained
interrupt controllers
- Conversion to bitmap_zalloc() throughout the irq chip drivers
- The usual set of small fixes and improvements"
* tag 'irq-core-2021-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (57 commits)
platform-msi: Add ABI to show msi_irqs of platform devices
genirq/msi: Move MSI sysfs handling from PCI to MSI core
genirq/cpuhotplug: Demote debug printk to KERN_DEBUG
irqchip/qcom-pdc: Trim unused levels of the interrupt hierarchy
irqdomain: Export irq_domain_disconnect_hierarchy()
irqchip/gic-v3: Fix priority comparison when non-secure priorities are used
irqchip/apple-aic: Fix irq_disable from within irq handlers
pinctrl/rockchip: drop the gpio related codes
gpio/rockchip: drop irq_gc_lock/irq_gc_unlock for irq set type
gpio/rockchip: support next version gpio controller
gpio/rockchip: use struct rockchip_gpio_regs for gpio controller
gpio/rockchip: add driver for rockchip gpio
dt-bindings: gpio: change items restriction of clock for rockchip,gpio-bank
pinctrl/rockchip: add pinctrl device to gpio bank struct
pinctrl/rockchip: separate struct rockchip_pin_bank to a head file
pinctrl/rockchip: always enable clock for gpio controller
genirq: Fix kernel doc indentation
EDAC/altera: Convert to generic_handle_domain_irq()
powerpc: Bulk conversion to generic_handle_domain_irq()
nios2: Bulk conversion to generic_handle_domain_irq()
...
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The SC8180x platform comes with PMC8180 and PMC8180c, add support for
the GPIO controller in these PMICs.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210629003851.1787673-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on CAF implementation with egpio/wake_reg support removed.
Similar function names were merged to reduce total number of functions.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210723192352.546902-3-iskren.chernev@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enabling the PINCTRL_SM8350 symbol without GPIOLIB or SCM causes a build
failure:
WARNING: unmet direct dependencies detected for PINCTRL_MSM
Depends on [m]: PINCTRL [=y] && (ARCH_QCOM [=y] || COMPILE_TEST [=y]) && GPIOLIB [=y] && (QCOM_SCM [=m] || !QCOM_SCM [=m])
Selected by [y]:
- PINCTRL_SM8350 [=y] && PINCTRL [=y] && (ARCH_QCOM [=y] || COMPILE_TEST [=y]) && GPIOLIB [=y] && OF [=y]
aarch64-linux-ld: drivers/pinctrl/qcom/pinctrl-msm.o: in function `msm_gpio_irq_set_type':
pinctrl-msm.c:(.text.msm_gpio_irq_set_type+0x1c8): undefined reference to `qcom_scm_io_readl'
The main problem here is the 'select PINCTRL_MSM', which needs to be a
'depends on' as it is for all the other front-ends. As the GPIOLIB
dependency is now implied by that, symbol, remove the duplicate
dependencies in the process.
Fixes: d5d348a327 ("pinctrl: qcom: Add SM8350 pinctrl driver")
Fixes: 376f9e34c1 ("drivers: pinctrl: qcom: fix Kconfig dependency on GPIOLIB")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210723091400.1669716-1-arnd@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New drivers:
- Last merge window we created a driver for the Ralink RT2880.
We are now moving the Ralink SoC pin control drivers out of the MIPS
architecture code and into the pin control subsystem. This concerns
RT288X, MT7620, RT305X, RT3883 and MT7621.
- Qualcomm SM6125 SoC pin control driver.
- Qualcomm spmi-gpio support for PM7325.
- Qualcomm spmi-mpp also handles PMI8994 (just a compatible string)
- Mediatek MT8365 SoC pin controller.
- New device HID for the AMD GPIO controller.
Improvements:
- Pin bias config support for a slew of Renesas pin controllers.
- Incremental improvements and non-urgent bug fixes to the Renesas
SoC drivers.
- Implement irq_set_wake on the AMD pin controller so we can wake
up from external pin events.
Misc:
- Devicetree bindings for the Apple M1 pin controller, we will probably
see a proper driver for this soon as well.
-----BEGIN PGP SIGNATURE-----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=Ajcr
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.14 kernel. Not so
much going on. No core changes, just drivers.
The most interesting would be that MIPS Ralink is migrating to pin
control and we have some bindings but not yet code for the Apple M1
pin controller.
New drivers:
- Last merge window we created a driver for the Ralink RT2880. We are
now moving the Ralink SoC pin control drivers out of the MIPS
architecture code and into the pin control subsystem. This concerns
RT288X, MT7620, RT305X, RT3883 and MT7621.
- Qualcomm SM6125 SoC pin control driver.
- Qualcomm spmi-gpio support for PM7325.
- Qualcomm spmi-mpp also handles PMI8994 (just a compatible string)
- Mediatek MT8365 SoC pin controller.
- New device HID for the AMD GPIO controller.
Improvements:
- Pin bias config support for a slew of Renesas pin controllers.
- Incremental improvements and non-urgent bug fixes to the Renesas
SoC drivers.
- Implement irq_set_wake on the AMD pin controller so we can wake up
from external pin events.
Misc:
- Devicetree bindings for the Apple M1 pin controller, we will
probably see a proper driver for this soon as well"
* tag 'pinctrl-v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (54 commits)
pinctrl: ralink: rt305x: add missing include
pinctrl: stm32: check for IRQ MUX validity during alloc()
pinctrl: zynqmp: some code cleanups
drivers: qcom: pinctrl: Add pinctrl driver for sm6125
dt-bindings: pinctrl: qcom: sm6125: Document SM6125 pinctrl driver
dt-bindings: pinctrl: mcp23s08: add documentation for reset-gpios
pinctrl: mcp23s08: Add optional reset GPIO
pinctrl: mediatek: fix mode encoding
pinctrl: mcp23s08: Fix missing unlock on error in mcp23s08_irq()
pinctrl: bcm: Constify static pinmux_ops
pinctrl: bcm: Constify static pinctrl_ops
pinctrl: ralink: move RT288X SoC pinmux config into a new 'pinctrl-rt288x.c' file
pinctrl: ralink: move MT7620 SoC pinmux config into a new 'pinctrl-mt7620.c' file
pinctrl: ralink: move RT305X SoC pinmux config into a new 'pinctrl-rt305x.c' file
pinctrl: ralink: move RT3883 SoC pinmux config into a new 'pinctrl-rt3883.c' file
pinctrl: ralink: move MT7621 SoC pinmux config into a new 'pinctrl-mt7621.c' file
pinctrl: ralink: move ralink architecture pinmux header into the driver
pinctrl: single: config: enable the pin's input
pinctrl: mtk: Fix mt8365 Kconfig dependency
pinctrl: mcp23s08: fix race condition in irq handler
...
It's currently not possible to select the SC8180x TLMM driver, due to it
selecting PINCTRL_MSM, rather than depending on the same. Fix this.
Fixes: 97423113ec ("pinctrl: qcom: Add sc8180x TLMM driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210608180702.2064253-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PMI8994 has 4 multi-purpose-pins, add a compatible for this hardware
block to the MPP driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210429003751.224232-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- A semantic change to handle pinmux and pinconf in explicit order
while up until now we depended on the semantic order in the
device tree. The device tree is a functional programming
language and does not imply any order, so the right thing is
for the pin control core to provide these semantics.
- Add a new pinmux-select debugfs file which makes it possible to
go in and select functions for a pin manually (iteratively, at
the prompt) for debugging purposes.
- Fixes to gpio regmap handling for a new pin control driver
making use of regmap-gpio.
- Use octal permissions on debugfs files.
New drivers:
- A massive rewrite of the former custom pin control driver for
MIPS Broadcom devices to instead use the pin control subsystem.
New pin control drivers for BCM6345, BCM6328, BCM6358, BCM6362,
BCM6368, BCM63268 and BCM6318 SoC variants are implemented.
- Support for PM8350, PM8350B, PM8350C, PMK8350, PMR735A and
PMR735B in the Qualcomm PMIC GPIO driver. Also the two GPIOs
on PM8008 are supported.
- Support for the Rockchip RK3568/RK3566 pin controller.
- Support for Ingenic JZ4730, JZ4750, JZ4755, JZ4775 and
X2000.
- Support for Mediatek MTK8195.
- Add a new Xilinx ZynqMP pin control driver.
Driver improvements and non-urgent fixes:
- Modularization and improvements of the Rockchip drivers.
- Some new pins added to the description of new Renesas SoCs.
- Clarifications of the GPIO base calculation in the Intel driver.
- Fix the function names for the MPP54 and MPP55 pins in the Armada
CP110 pin controller.
- GPIO wakeup interrupt map for Qualcomm SC7280 and SM8350.
- Support for ACPI probing of the Qualcomm SC8180x.
- Fix interrupt clear status on rockchip
- Fix some missing pins on the Ingenic JZ4770, some semantic
fixes for the behaviour of the Ingenic pin controller.
Add DMIC pins for JZ4780, X1000, X1500 and X1830.
- A slew of janitorial like of_node_put() calls.
-----BEGIN PGP SIGNATURE-----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=QrEn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"There is a lot going on!
Core changes:
- A semantic change to handle pinmux and pinconf in explicit order
while up until now we depended on the semantic order in the device
tree. The device tree is a functional programming language and does
not imply any order, so the right thing is for the pin control core
to provide these semantics.
- Add a new pinmux-select debugfs file which makes it possible to go
in and select functions for a pin manually (iteratively, at the
prompt) for debugging purposes.
- Fixes to gpio regmap handling for a new pin control driver making
use of regmap-gpio.
- Use octal permissions on debugfs files.
New drivers:
- A massive rewrite of the former custom pin control driver for MIPS
Broadcom devices to instead use the pin control subsystem. New pin
control drivers for BCM6345, BCM6328, BCM6358, BCM6362, BCM6368,
BCM63268 and BCM6318 SoC variants are implemented.
- Support for PM8350, PM8350B, PM8350C, PMK8350, PMR735A and PMR735B
in the Qualcomm PMIC GPIO driver. Also the two GPIOs on PM8008 are
supported.
- Support for the Rockchip RK3568/RK3566 pin controller.
- Support for Ingenic JZ4730, JZ4750, JZ4755, JZ4775 and X2000.
- Support for Mediatek MTK8195.
- Add a new Xilinx ZynqMP pin control driver.
Driver improvements and non-urgent fixes:
- Modularization and improvements of the Rockchip drivers.
- Some new pins added to the description of new Renesas SoCs.
- Clarifications of the GPIO base calculation in the Intel driver.
- Fix the function names for the MPP54 and MPP55 pins in the Armada
CP110 pin controller.
- GPIO wakeup interrupt map for Qualcomm SC7280 and SM8350.
- Support for ACPI probing of the Qualcomm SC8180x.
- Fix interrupt clear status on rockchip
- Fix some missing pins on the Ingenic JZ4770, some semantic fixes
for the behaviour of the Ingenic pin controller. Add DMIC pins for
JZ4780, X1000, X1500 and X1830.
- A slew of janitorial like of_node_put() calls"
* tag 'pinctrl-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: Add Xilinx ZynqMP pinctrl driver support
firmware: xilinx: Add pinctrl support
pinctrl: rockchip: do coding style for mux route struct
pinctrl: Add PIN_CONFIG_MODE_PWM to enum pin_config_param
pinctrl: Introduce MODE group in enum pin_config_param
pinctrl: Keep enum pin_config_param ordered by name
dt-bindings: pinctrl: Add binding for ZynqMP pinctrl driver
pinctrl: core: Fix kernel doc string for pin_get_name()
pinctrl: mediatek: use spin lock in mtk_rmw
pinctrl: add drive for I2C related pins on MT8195
pinctrl: add pinctrl driver on mt8195
dt-bindings: pinctrl: mt8195: add pinctrl file and binding document
pinctrl: Ingenic: Add pinctrl driver for X2000.
pinctrl: Ingenic: Add pinctrl driver for JZ4775.
pinctrl: Ingenic: Add pinctrl driver for JZ4755.
pinctrl: Ingenic: Add pinctrl driver for JZ4750.
pinctrl: Ingenic: Add pinctrl driver for JZ4730.
dt-bindings: pinctrl: Add bindings for new Ingenic SoCs.
pinctrl: Ingenic: Reformat the code.
pinctrl: Ingenic: Add DMIC pins support for Ingenic SoCs.
...
When PINCTRL_MSM is enabled, and GPIOLIB is disabled,
Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for GPIOLIB_IRQCHIP
Depends on [n]: GPIOLIB [=n]
Selected by [y]:
- PINCTRL_MSM [=y] && PINCTRL [=y] && (ARCH_QCOM || COMPILE_TEST [=y])
This is because PINCTRL_MSM selects GPIOLIB_IRQCHIP,
without selecting or depending on GPIOLIB, despite
GPIOLIB_IRQCHIP depending on GPIOLIB. Having PINCTRL_MSM
select GPIOLIB will cause a recursive dependency error.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210414025138.480085-1-julianbraha@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
clang is clearly correct to point out a typo in a silly
array of strings:
drivers/pinctrl/qcom/pinctrl-sdx55.c:426:61: error: suspicious concatenation of string literals in an array initialization; did you mean to separate the elements with a comma? [-Werror,-Wstring-concatenation]
"gpio14", "gpio15", "gpio16", "gpio17", "gpio18", "gpio19" "gpio20", "gpio21", "gpio22",
^
Add the missing comma that must have accidentally been removed.
Fixes: ac43c44a7a ("pinctrl: qcom: Add SDX55 pincontrol driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210323131728.2702789-1-arnd@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It adds ACPI probe support for pinctrl-sc8180x driver. We have one
problem with ACPI table, i.e. GIO0 (TLMM) block has one single memory
resource to cover 3 tiles defined by SC8180X. To follow the hardware
layout of 3 tiles which is already supported DT probe, it adds one
function to replace the original single memory resource with 3 named
ones for tiles. With that, We can map memory for ACPI in the same way
as DT.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20210311024102.15450-1-shawn.guo@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOs that can be configured as wakeup sources, have their interrupt
lines routed to PDC interrupt controller. Provide the interrupt map of
the GPIO to its wakeup capable interrupt parent.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210312034218.3324410-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the PM8350, PM8350B, PM8350C, PMK8350, PMR735A and
PMR735B GPIO support to the Qualcomm PMIC GPIO driver.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210308164845.3210393-2-vkoul@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix SDC1_RCLK configurations which are in a different register so fix the
offset from 0xb3000 to 0xb3004.
Fixes: ecb454594c: ("pinctrl: qcom: Add sc7280 pinctrl driver")
Reported-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1614662511-26519-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The offsets for SDC_QDSD_PINGROUP and UFS_RESET were off by 0x100000
due to an issue in the scripts generating the data.
Fixes: ecb454594c: ("pinctrl: qcom: Add sc7280 pinctrl driver")
Reported-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1614662511-26519-1-git-send-email-rnayak@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If these fields are not set in dts, the driver will use these variables
uninitialized to set the fields. Not only will it set garbage values for
these fields, but it can overflow into other fields and break those.
In the current sm8250 dts, the dmic01 entries do not have a pullup setting,
and might not work without this change.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 6e261d1090 ("pinctrl: qcom: Add sm8250 lpass lpi pinctrl driver")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210304194816.3843-1-jonathan@marek.ca
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOs that can be configured as wakeup sources, have their
interrupt lines routed to PDC interrupt controller.
Provide the interrupt map of the GPIO to its wakeup capable
interrupt parent.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1613105974-28181-1-git-send-email-rnayak@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This time a calm set with no core changes.
New drivers/subdrivers:
- Renesas R8A7790A0 pin controller.
- Allwinner H616 and H616-R pin controllers.
- Qualcomm SM8350 and SC8180x pin controllers.
Improvements:
- Redo the DT bindings for Ralink RT2880.
- A common Qualcomm TLMM DT binding in YAML.
- Delete the unused drivers for U300, COH901, Sirf Atlas, and ZTE ZX.
-----BEGIN PGP SIGNATURE-----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=WKZ8
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.12 kernel.
This time a calm set with no core changes.
New drivers/subdrivers:
- Renesas R8A7790A0 pin controller.
- Allwinner H616 and H616-R pin controllers.
- Qualcomm SM8350 and SC8180x pin controllers.
Improvements:
- Redo the DT bindings for Ralink RT2880.
- A common Qualcomm TLMM DT binding in YAML.
- Delete the unused drivers for U300, COH901, Sirf Atlas, and ZTE ZX"
* tag 'pinctrl-v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (71 commits)
pinctrl: mediatek: Fix trigger type setting follow for unexpected interrupt
dt-bindings: pinctrl: Group tuples in pin control properties
pinctrl: nuvoton: npcm7xx: Fix alignment of table header comment
pinctrl: at91-pio4: fix "Prefer 'unsigned int' to bare use of 'unsigned'"
pinctrl: at91-pio4: add support for slew-rate
dt-bindings: pinctrl: at91-pio4: add slew-rate
pinctrl: actions: Add depends on || COMPILE_TEST
pinctrl: single: set function name when adding function
pinctrl: qcom: Add sc8180x TLMM driver
dt-bindings: pinctrl: qcom: Add sc8180x binding
dt-bindings: pinctrl: qcom: Define common TLMM binding
pinctrl: qcom: Add SM8350 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8350 pinctrl bindings
pinctrl: samsung: use raw_spinlock for s3c64xx
dt-bindings: mediatek: mt8192: Fix dt_binding_check warning
pinctrl: qcom: spmi-mpp: Add PM8019 compatible
pinctrl: pinmux: add function selector to pinmux-functions
pinctrl: samsung: use raw_spinlock for locking
pinctrl: clarify #pinctrl-cells for pinctrl-single,pins
pinctrl: actions: Add the platform dependency to drivers
...
Add pinctrl driver for the sc8180x TLMM block.
A noteworthy difference from previous TLMM blocks is that the registers
for GPIO 177 through 189 are for some reason offset from the typical
layout. Other than that the driver is same old...
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210126042650.1725176-3-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pincontrol driver for tlmm block found in SM8350 SoC
This patch is based on initial code downstream by Raghavendra.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210205140132.274242-3-vkoul@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In Linux, if a driver does disable_irq() and later does enable_irq()
on its interrupt, I believe it's expecting these properties:
* If an interrupt was pending when the driver disabled then it will
still be pending after the driver re-enables.
* If an edge-triggered interrupt comes in while an interrupt is
disabled it should assert when the interrupt is re-enabled.
If you think that the above sounds a lot like the disable_irq() and
enable_irq() are supposed to be masking/unmasking the interrupt
instead of disabling/enabling it then you've made an astute
observation. Specifically when talking about interrupts, "mask"
usually means to stop posting interrupts but keep tracking them and
"disable" means to fully shut off interrupt detection. It's
unfortunate that this is so confusing, but presumably this is all the
way it is for historical reasons.
Perhaps more confusing than the above is that, even though clients of
IRQs themselves don't have a way to request mask/unmask
vs. disable/enable calls, IRQ chips themselves can implement both.
...and yet more confusing is that if an IRQ chip implements
disable/enable then they will be called when a client driver calls
disable_irq() / enable_irq().
It does feel like some of the above could be cleared up. However,
without any other core interrupt changes it should be clear that when
an IRQ chip gets a request to "disable" an IRQ that it has to treat it
like a mask of that IRQ.
In any case, after that long interlude you can see that the "unmask
and clear" can break things. Maulik tried to fix it so that we no
longer did "unmask and clear" in commit 71266d9d39 ("pinctrl: qcom:
Move clearing pending IRQ to .irq_request_resources callback"), but it
only handled the PDC case and it had problems (it caused
sc7180-trogdor devices to fail to suspend). Let's fix.
>From my understanding the source of the phantom interrupt in the
were these two things:
1. One that could have been introduced in msm_gpio_irq_set_type()
(only for the non-PDC case).
2. Edges could have been detected when a GPIO was muxed away.
Fixing case #1 is easy. We can just add a clear in
msm_gpio_irq_set_type().
Fixing case #2 is harder. Let's use a concrete example. In
sc7180-trogdor.dtsi we configure the uart3 to have two pinctrl states,
sleep and default, and mux between the two during runtime PM and
system suspend (see geni_se_resources_{on,off}() for more
details). The difference between the sleep and default state is that
the RX pin is muxed to a GPIO during sleep and muxed to the UART
otherwise.
As per Qualcomm, when we mux the pin over to the UART function the PDC
(or the non-PDC interrupt detection logic) is still watching it /
latching edges. These edges don't cause interrupts because the
current code masks the interrupt unless we're entering suspend.
However, as soon as we enter suspend we unmask the interrupt and it's
counted as a wakeup.
Let's deal with the problem like this:
* When we mux away, we'll mask our interrupt. This isn't necessary in
the above case since the client already masked us, but it's a good
idea in general.
* When we mux back will clear any interrupts and unmask.
Fixes: 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Fixes: 71266d9d39 ("pinctrl: qcom: Move clearing pending IRQ to .irq_request_resources callback")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210114191601.v7.4.I7cf3019783720feb57b958c95c2b684940264cd1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In commit 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for
msm gpio") we tried to Ack interrupts during unmask. However, that
patch forgot to check "intr_ack_high" so, presumably, it only worked
for a certain subset of SoCs.
Let's add a small accessor so we don't need to open-code the logic in
both places.
This was found by code inspection. I don't have any access to the
hardware in question nor software that needs the Ack during unmask.
Fixes: 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.3.I32d0f4e174d45363b49ab611a13c3da8f1e87d0f@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the Qualcomm pinctrl driver wants to Ack an interrupt, it does a
read-modify-write on the interrupt status register. On some SoCs it
makes sure that the status bit is 1 to "Ack" and on others it makes
sure that the bit is 0 to "Ack". Presumably the first type of
interrupt controller is a "write 1 to clear" type register and the
second just let you directly set the interrupt status register.
As far as I can tell from scanning structure definitions, the
interrupt status bit is always in a register by itself. Thus with
both types of interrupt controllers it is safe to "Ack" interrupts
without doing a read-modify-write. We can do a simple write.
It should be noted that if the interrupt status bit _was_ ever in a
register with other things (like maybe status bits for other GPIOs):
a) For "write 1 clear" type controllers then read-modify-write would
be totally wrong because we'd accidentally end up clearing
interrupts we weren't looking at.
b) For "direct set" type controllers then read-modify-write would also
be wrong because someone setting one of the other bits in the
register might accidentally clear (or set) our interrupt.
I say this simply to show that the current read-modify-write doesn't
provide any sort of "future proofing" of the code. In fact (for
"write 1 clear" controllers) the new code is slightly more "future
proof" since it would allow more than one interrupt status bits to
share a register.
NOTE: this code fixes no bugs--it simply avoids an extra register
read.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.2.I3635de080604e1feda770591c5563bd6e63dd39d@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There's currently a comment in the code saying function 0 is GPIO.
Instead of hardcoding it, let's add a member where an SoC can specify
it. No known SoCs use a number other than 0, but this just makes the
code clearer. NOTE: no SoC code needs to be updated since we can rely
on zero-initialization.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.1.I3ad184e3423d8e479bc3e86f5b393abb1704a1d1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove all empty lines at the end of functions in pinctrl subsystem,
and make the code neat.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Zhaoyu Liu <zackaryliu@yeah.net>
Link: https://lore.kernel.org/r/X98NP6NFK1Afzrgd@manjaro
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New drivers:
- New driver for the Microchip Serial GPIO "SGPIO".
- Qualcomm SM8250 LPASS (Low Power Audio Subsystem) GPIO driver.
New subdrivers:
- Intel Lakefield subdriver.
- Intel Elkhart Lake subdriver.
- Intel Alder Lake-S subdriver.
- Qualcomm MSM8953 subdriver.
- Qualcomm SDX55 subdriver.
- Qualcomm SDX55 PMIC subdriver.
- Ocelot Luton SoC subdriver.
- Ocelot Serval SoC subdriver.
Modularization:
- The Meson driver can now be built as modules.
- The Qualcomm driver(s) can now be built as modules.
Incremental improvements:
- The Intel driver now supports pin configuration for GPIO-related
configurations.
- A bunch of Renesas PFC drivers have been augmented with support
for QSPI pins, groups and functions.
- Non-critical fixes to the irq handling in the Allwinner Sunxi
driver.
-----BEGIN PGP SIGNATURE-----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=e5sV
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.11 kernel.
Drivers, drivers and drivers. Not a single core change.
Some new stuff, especially a bunch of new Intel, Qualcomm and Ocelot
SoCs.
As part of the modularization attempt, I applied one patch affecting
the firmware subsystem as a functional (not syntactic/semantic)
dependency and then it blew up in our face, so I had to revert it,
bummer. It will come in later, through that subsystem, I guess.
New drivers:
- New driver for the Microchip Serial GPIO "SGPIO".
- Qualcomm SM8250 LPASS (Low Power Audio Subsystem) GPIO driver.
New subdrivers:
- Intel Lakefield subdriver.
- Intel Elkhart Lake subdriver.
- Intel Alder Lake-S subdriver.
- Qualcomm MSM8953 subdriver.
- Qualcomm SDX55 subdriver.
- Qualcomm SDX55 PMIC subdriver.
- Ocelot Luton SoC subdriver.
- Ocelot Serval SoC subdriver.
Modularization:
- The Meson driver can now be built as modules.
- The Qualcomm driver(s) can now be built as modules.
Incremental improvements:
- The Intel driver now supports pin configuration for GPIO-related
configurations.
- A bunch of Renesas PFC drivers have been augmented with support for
QSPI pins, groups and functions.
- Non-critical fixes to the irq handling in the Allwinner Sunxi
driver"
* tag 'pinctrl-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
pinctrl/spear: simplify the return expression of spear300_pinctrl_probe()
pinctrl: mediatek: simplify the return expression of mtk_pinconf_bias_disable_set_rev1()
dt-bindings: pinctrl: pinctrl-microchip-sgpio: Add irq support
pinctrl: pinctrl-microchip-sgpio: Add irq support (for sparx5)
pinctrl: qcom: Add sm8250 lpass lpi pinctrl driver
dt-bindings: pinctrl: qcom: Add sm8250 lpass lpi pinctrl bindings
pinctrl: qcom-pmic-gpio: Add support for pmx55
dt-bindings: pinctrl: qcom-pmic-gpio: Add pmx55 support
pinctrl: pinctrl-microchip-sgpio: Mark some symbols with static keyword
pinctrl: at91-pio4: Make PINCTRL_AT91PIO4 depend on HAS_IOMEM to fix build error
pinctrl: mtk: Fix low level output voltage issue
pinctrl: falcon: add missing put_device() call in pinctrl_falcon_probe()
pinctrl: actions: pinctrl-s500: Constify s500_padinfo[]
pinctrl: pinctrl-microchip-sgpio: Add OF config dependency
pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO
dt-bindings: pinctrl: Add bindings for pinctrl-microchip-sgpio driver
pinctrl: at91-pio4: add support for fewer lines on last PIO bank
pinctrl: sunxi: Always call chained_irq_{enter, exit} in sunxi_pinctrl_irq_handler
pinctrl: sunxi: Mark the irq bank not found in sunxi_pinctrl_irq_handler() with WARN_ON
pinctrl: sunxi: fix irq bank map for the Allwinner A100 pin controller
...
Add initial pinctrl driver to support pin configuration for
LPASS (Low Power Audio SubSystem) LPI (Low Power Island) pinctrl
on SM8250.
This IP is an additional pin control block for Audio Pins on top the
existing SoC Top level pin-controller.
Hardware setup looks like:
TLMM GPIO[146 - 159] --> LPASS LPI GPIO [0 - 13]
This pin controller has some similarities compared to Top level
msm SoC Pin controller like 'each pin belongs to a single group'
and so on. However this one is intended to control only audio
pins in particular, which can not be configured/touched by the
Top level SoC pin controller except setting them as gpios.
Apart from this, slew rate is also available in this block for
certain pins which are connected to SLIMbus or SoundWire Bus.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201202163443.26499-3-srinivas.kandagatla@linaro.org
[Add some dependencies]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One fixup following my patch commit be117ca322 ("pinctrl:
qcom: Kconfig: Rework PINCTRL_MSM to be a depenency rather then
a selected config") being queued in LinusW's tree, as a new
config entry was added for the msm8953 that also needs the
change.
Applies to LinusW's pinctrl devel tree.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Prasad Sodagudi <psodagud@codeaurora.org>
Cc: Vladimir Lypak <junak.pub@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Link: https://lore.kernel.org/r/20201110215619.86076-1-john.stultz@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit be117ca322 ("pinctrl: qcom: Kconfig: Rework PINCTRL_MSM to be a
dependency rather then a selected config") moved the qcom pinctrl drivers
to have PINCTRL_MSM as dependency rather then a selected config, so do
this change for SDX55 pinctrl driver as well.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201111043610.177168-1-vkoul@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tweaks to allow pinctrl-msm code to be loadable as a module.
This is needed in order to support having the qcom-scm driver,
which pinctrl-msm calls into, configured as a module.
This requires that we tweak Kconfigs selecting PINCTRL_MSM to
also depend on QCOM_SCM || QCOM_SCM=n so that we match the
module setting of QCOM_SCM.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-gpio@vger.kernel.org
Link: https://lore.kernel.org/r/20201106042710.55979-2-john.stultz@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch reworks PINCTRL_MSM to be a visible option, and
instead of having the various SoC specific drivers select
PINCTRL_MSM, this switches those configs to depend on
PINCTRL_MSM.
This is useful, as it will be needed in order to cleanly support
having the qcom-scm driver, which pinctrl-msm calls into,
configured as a module. Without this change, we would eventually
have to add dependency lines to every config that selects
PINCTRL_MSM, and that would becomes a maintenance headache.
We also add PINCTRL_MSM to the arm64 defconfig to avoid
surprises as otherwise PINCTRL_MSM/IPQ* options previously
enabled, will be off.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-gpio@vger.kernel.org
Link: https://lore.kernel.org/r/20201106042710.55979-1-john.stultz@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Specify the PDC mapping for SM8250, so that gpio interrupts are
propertly mapped to the wakeup IRQs of the PDC.
Fixes: 4e3ec9e407 ("pinctrl: qcom: Add sm8250 pinctrl driver.")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201028043642.1141723-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When GPIOs that are routed to PDC are used as output they can still latch
the IRQ pending at GIC. As a result the spurious IRQ was handled when the
client driver change the direction to input to starts using it as IRQ.
Currently such erroneous latched IRQ are cleared with .irq_enable callback
however if the driver continue to use GPIO as interrupt and invokes
disable_irq() followed by enable_irq() then everytime during enable_irq()
previously latched interrupt gets cleared.
This can make edge IRQs not seen after enable_irq() if they had arrived
after the driver has invoked disable_irq() and were pending at GIC.
Move clearing erroneous IRQ to .irq_request_resources callback as this is
the place where GPIO direction is changed as input and its locked as IRQ.
While at this add a missing check to invoke msm_gpio_irq_clear_unmask()
from .irq_enable callback only when GPIO is not routed to PDC.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1604561884-10166-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- NONE whatsoever, we don't even touch the core files this
time around.
New drivers:
- New driver for the Toshiba Visconti SoC.
- New subdriver for the Qualcomm MSM8226 SoC.
- New subdriver for the Actions Semiconductor S500 SoC.
- New subdriver for the Mediatek MT8192 SoC.
- New subdriver for the Microchip SAMA7G5 SoC.
Driver enhancements:
- Intel Cherryview and Baytrail cleanups and refactorings.
- Enhanced support for the Renesas R8A7790, more pins and
groups.
- Some optimizations for the MCP23S08 MCP23x17 variant.
- Some cleanups around the Actions Semiconductor subdrivers.
- A bunch of cleanups around the SH-PFC and Emma Mobile
drivers.
- The "SH-PFC" (literally SuperH pin function controller, I
think) subdirectory is now renamed to the more neutral
"renesas", as these are not very much centered around
SuperH anymore.
- Non-critical fixes for the Aspeed driver.
- Non-critical fixes for the Ingenic (MIPS!) driver.
- Fix a bunch of missing pins on the AMD pinctrl driver.
-----BEGIN PGP SIGNATURE-----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=TdjX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- NONE whatsoever, we don't even touch the core files this time
around.
New drivers:
- New driver for the Toshiba Visconti SoC.
- New subdriver for the Qualcomm MSM8226 SoC.
- New subdriver for the Actions Semiconductor S500 SoC.
- New subdriver for the Mediatek MT8192 SoC.
- New subdriver for the Microchip SAMA7G5 SoC.
Driver enhancements:
- Intel Cherryview and Baytrail cleanups and refactorings.
- Enhanced support for the Renesas R8A7790, more pins and groups.
- Some optimizations for the MCP23S08 MCP23x17 variant.
- Some cleanups around the Actions Semiconductor subdrivers.
- A bunch of cleanups around the SH-PFC and Emma Mobile drivers.
- The "SH-PFC" (literally SuperH pin function controller, I think)
subdirectory is now renamed to the more neutral "renesas", as these
are not very much centered around SuperH anymore.
- Non-critical fixes for the Aspeed driver.
- Non-critical fixes for the Ingenic (MIPS!) driver.
- Fix a bunch of missing pins on the AMD pinctrl driver"
* tag 'pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (78 commits)
pinctrl: amd: Add missing pins to the pin group list
dt-bindings: pinctrl: sunxi: Allow pinctrl with more interrupt banks
pinctrl: visconti: PINCTRL_TMPV7700 should depend on ARCH_VISCONTI
pinctrl: mediatek: Free eint data on failure
pinctrl: single: fix debug output when #pinctrl-cells = 2
pinctrl: single: fix pinctrl_spec.args_count bounds check
pinctrl: sunrisepoint: Modify COMMUNITY macros to be consistent
pinctrl: cannonlake: Modify COMMUNITY macros to be consistent
pinctrl: tigerlake: Fix register offsets for TGL-H variant
pinctrl: Document pinctrl-single,pins when #pinctrl-cells = 2
pinctrl: mediatek: use devm_platform_ioremap_resource_byname()
pinctrl: nuvoton: npcm7xx: Constify static ops structs
pinctrl: mediatek: mt7622: add antsel pins/groups
pinctrl: ocelot: simplify the return expression of ocelot_gpiochip_register()
pinctrl: at91-pio4: add support for sama7g5 SoC
dt-bindings: pinctrl: at91-pio4: add microchip,sama7g5
pinctrl: spear: simplify the return expression of tvc_connect()
pinctrl: spear: simplify the return expression of spear310_pinctrl_probe
pinctrl: sprd: use module_platform_driver to simplify the code
pinctrl: Ingenic: Add I2S pins support for Ingenic SoCs.
...
Core:
- Allow trimming of interrupt hierarchy to support odd hardware setups
where only a subset of the interrupts requires the full hierarchy.
- Allow the retrigger mechanism to follow a hierarchy to simplify
driver code.
- Provide a mechanism to force enable wakeup interrrupts on suspend.
- More infrastructure to handle IPIs in the core code
Architectures:
- Convert ARM/ARM64 IPI handling to utilize the interrupt core code.
Drivers:
- The usual pile of new interrupt chips (MStar, Actions Owl, TI PRUSS,
Designware ICTL)
- ARM(64) IPI related conversions
- Wakeup support for Qualcom PDC
- Prevent hierarchy corruption in the NVIDIA Tegra driver
- The usual small fixes, improvements and cleanups all over the place.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAl+ENDsTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoTyXD/9oGq37/zjpCggtRWdTKGtKvndjodqt
82zTZ1eSukDSE3UoT7PL8cRQ/4MnRZ7Ke+Iidd2uUbWADfJN28+4d26wN/aYYlX7
HmI/zowBgK6CJweynHYEF9/C8g2v2SRg5HJCJSOSuVLnTKNLc/aHX5rc/FZXGd6v
K1BOHJFlzoU1w+OnFfoH4TeJdoKhzXi/T5zJFFtadOVIeCONxTEs4Fxkej2cuBsu
Nz38WfkPdOnyrVIPhA10KgigczcRkKXU0ot/bNH4s9j2ZIGdgtq3UIbH+itleW2S
bSWSShnlhSMS918pZNcR49iRyP2CsM+JxcHAmcbA6VPBpKbk2Pb5Zta8g08TZm+X
XxaDwPFoR4BG00B0L4uygEuHcE89mDy0gCFog0zG7sU+LuY4FYQSSMUqwIC4i/HJ
DJdWrVqnNHJFCS6wvBl9NO0lyuUrn2be2/IzUtZ3d0xbA0uJXfvI4WgFrbunoPEU
zgHblQN5nkDLWujjzC10C9vmTi1xxP6FiYcrMScZZ5US0JlHaptkoPOhs82KYQvV
0DPk06XGWnJMc27+MQYVIMDhQggi3It9pgDRhoyz9Xpgn9fmhhp0goL7KnFk9Hbr
BKFdW4VBbU0PZacoI6Q186lTQZRptTKfREL+bHvUL2Xyb0RO6nerBPzE5Wxwb2vW
PmHgFezXDVHbIQ==
=1ewL
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core:
- Allow trimming of interrupt hierarchy to support odd hardware
setups where only a subset of the interrupts requires the full
hierarchy.
- Allow the retrigger mechanism to follow a hierarchy to simplify
driver code.
- Provide a mechanism to force enable wakeup interrrupts on suspend.
- More infrastructure to handle IPIs in the core code
Architectures:
- Convert ARM/ARM64 IPI handling to utilize the interrupt core code.
Drivers:
- The usual pile of new interrupt chips (MStar, Actions Owl, TI
PRUSS, Designware ICTL)
- ARM(64) IPI related conversions
- Wakeup support for Qualcom PDC
- Prevent hierarchy corruption in the NVIDIA Tegra driver
- The usual small fixes, improvements and cleanups all over the
place"
* tag 'irq-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
dt-bindings: interrupt-controller: Add MStar interrupt controller
irqchip/irq-mst: Add MStar interrupt controller support
soc/tegra: pmc: Don't create fake interrupt hierarchy levels
soc/tegra: pmc: Allow optional irq parent callbacks
gpio: tegra186: Allow optional irq parent callbacks
genirq/irqdomain: Allow partial trimming of irq_data hierarchy
irqchip/qcom-pdc: Reset PDC interrupts during init
irqchip/qcom-pdc: Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
pinctrl: qcom: Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
genirq/PM: Introduce IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
pinctrl: qcom: Use return value from irq_set_wake() call
pinctrl: qcom: Set IRQCHIP_SET_TYPE_MASKED and IRQCHIP_MASK_ON_SUSPEND flags
ARM: Handle no IPI being registered in show_ipi_list()
MAINTAINERS: Add entries for Actions Semi Owl SIRQ controller
irqchip: Add Actions Semi Owl SIRQ controller
dt-bindings: interrupt-controller: Add Actions SIRQ controller binding
dt-bindings: dw-apb-ictl: Update binding to describe use as primary interrupt controller
irqchip/dw-apb-ictl: Add primary interrupt controller support
irqchip/dw-apb-ictl: Refactor priot to introducing hierarchical irq domains
genirq: Add stub for set_handle_irq() when !GENERIC_IRQ_MULTI_HANDLER
...
Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag to enable/unmask the
wakeirqs during suspend entry.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-5-git-send-email-mkshah@codeaurora.org
msmgpio irqchip was not using return value of irq_set_irq_wake() callback
since previously GIC-v3 irqchip neither had IRQCHIP_SKIP_SET_WAKE flag nor
it implemented .irq_set_wake callback. This lead to irq_set_irq_wake()
return error -ENXIO.
However from 'commit 4110b5cbb0 ("irqchip/gic-v3: Allow interrupt to be
configured as wake-up sources")' GIC irqchip has IRQCHIP_SKIP_SET_WAKE
flag.
Use return value from irq_set_irq_wake() and irq_chip_set_wake_parent()
instead of always returning success.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-3-git-send-email-mkshah@codeaurora.org
Both IRQCHIP_SET_TYPE_MASKED and IRQCHIP_MASK_ON_SUSPEND flags are already
set for msmgpio's parent PDC irqchip but GPIO interrupts do not get masked
during suspend or during setting irq type since genirq checks irqchip flag
of msmgpio irqchip which forwards these calls to its parent PDC irqchip.
Add irqchip specific flags for msmgpio irqchip to mask non wakeirqs during
suspend and mask before setting irq type. Masking before changing type make
sures any spurious interrupt is not detected during this operation.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-2-git-send-email-mkshah@codeaurora.org
Add initial Qualcomm msm8226 pinctrl driver to support pin configuration
with pinctrl framework for msm8226 SoC.
- Initial formatting and style was taken from the msm8x74 pinctrl driver
added by Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bartosz Dudziak <bartosz.dudziak@snejp.pl>
Link: https://lore.kernel.org/r/20200716205530.22910-3-bartosz.dudziak@snejp.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernel series:
Core changes:
- The GPIO patch "gpiolib: Introduce
for_each_requested_gpio_in_range() macro" was put in an
immutable branch and merged into the pinctrl tree as well.
We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among
other things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have
been modularized. This is driven by the Google Android
GKI initiative I think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
-----BEGIN PGP SIGNATURE-----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=mJgb
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of the pin control changes for the v5.9 kernel
series:
Core changes:
- The GPIO patch "gpiolib: Introduce for_each_requested_gpio_in_range()
macro" was put in an immutable branch and merged into the pinctrl
tree as well. We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among other
things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have been
modularized. This is driven by the Google Android GKI initiative I
think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
* tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (107 commits)
dt-bindings: pinctrl: add bindings for MediaTek MT6779 SoC
pinctrl: stmfx: Use irqchip template
pinctrl: amd: Use irqchip template
pinctrl: mediatek: fix build for tristate changes
pinctrl: samsung: Use bank name as irqchip name
pinctrl: core: print gpio in pins debugfs file
pinctrl: mediatek: add mt6779 eint support
pinctrl: mediatek: add pinctrl support for MT6779 SoC
pinctrl: mediatek: avoid virtual gpio trying to set reg
pinctrl: mediatek: update pinmux definitions for mt6779
pinctrl: stm32: use the hwspin_lock_timeout_in_atomic() API
pinctrl: mcp23s08: Use irqchip template
pinctrl: sx150x: Use irqchip template
dt-bindings: ingenic,pinctrl: Support pinmux/pinconf nodes
pinctrl: intel: Add Intel Emmitsburg pin controller support
pinctl: ti: iodelay: Replace HTTP links with HTTPS ones
Revert "gpio: omap: handle pin config bias flags"
pinctrl: single: Use fallthrough pseudo-keyword
pinctrl: qcom: spmi-gpio: Use fallthrough pseudo-keyword
pinctrl: baytrail: Use fallthrough pseudo-keyword
...
Depending on how you look at it, you can either say that:
a) There is a PDC hardware issue (with the specific IP rev that exists
on sc7180) that causes the PDC not to work properly when configured
to handle dual edges.
b) The dual edge feature of the PDC hardware was only added in later
HW revisions and thus isn't in all hardware.
Regardless of how you look at it, let's work around the lack of dual
edge support by only ever letting our parent see requests for single
edge interrupts on affected hardware.
NOTE: it's possible that a driver requesting a dual edge interrupt
might get several edges coalesced into a single IRQ. For instance if
a line starts low and then goes high and low again, the driver that
requested the IRQ is not guaranteed to be called twice. However, it
is guaranteed that once the driver's interrupt handler starts running
its first instruction that any new edges coming in will cause the
interrupt to fire again. This is relatively commonplace for dual-edge
gpio interrupts (many gpio controllers require software to emulate
dual edge with single edge) so client drivers should be setup to
handle it.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200714080254.v3.1.Ie0d730120b232a86a4eac1e2909bcbec844d1766@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes the following W=1 kernel build warning(s):
drivers/pinctrl/qcom/pinctrl-msm8976.c:802:27: warning: ‘nav_tsync_groups’ defined but not used [-Wunused-const-variable=]
802 | static const char
const nav_tsync_groups[] = {
| ^~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Del Regno <kholk11@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Link: https://lore.kernel.org/r/20200713144930.1034632-10-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add missing descriptions for attributes and fix 1 formatting issue.
Fixes the following W=1 kernel build warning(s):
drivers/pinctrl/qcom/pinctrl-msm.c:75: warning: Function parameter or member 'desc' not described in 'msm_pinctrl'
drivers/pinctrl/qcom/pinctrl-msm.c:75: warning: Function parameter or member 'irq_chip' not described in 'msm_pinctrl'
drivers/pinctrl/qcom/pinctrl-msm.c:75: warning: Function parameter or member 'intr_target_use_scm' not described in 'msm_pinctrl'
drivers/pinctrl/qcom/pinctrl-msm.c:75: warning: Function parameter or member 'soc' not described in 'msm_pinctrl'
drivers/pinctrl/qcom/pinctrl-msm.c:75: warning: Function parameter or member 'phys_base' not described in 'msm_pinctrl'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Link: https://lore.kernel.org/r/20200713144930.1034632-6-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[ Brian: adapted from from the Chromium OS kernel used on IPQ4019-based
WiFi APs. ]
Signed-off-by: Jaiganesh Narayanan <njaigane@codeaurora.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Link: https://lore.kernel.org/r/20200703080646.23233-1-computersforpeace@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for pm660(l) SPMI GPIOs. The PMICs feature
13 and 12 GPIOs respectively, though with a lot of
holes inbetween.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622192558.152828-2-konradybcio@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch adds missing qpic data pins to qpic pingroup. These pins are
necessary for the qpic nand to work.
Fixes: ef1ea54eab ("pinctrl: qcom: Add ipq6018 pinctrl driver")
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Link: https://lore.kernel.org/r/1592541089-17700-1-git-send-email-sivaprak@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following warnings caused by reusage of the same irq_chip
instance for all spmi-gpio gpio_irq_chip instances. Instead embed
irq_chip into pmic_gpio_state struct.
gpio gpiochip2: (c440000.qcom,spmi:pmic@2:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip3: (c440000.qcom,spmi:pmic@4:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip4: (c440000.qcom,spmi:pmic@a:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200604002817.667160-1-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernel cycle.
New drivers:
- Intel Jasper Lake support.
- NXP Freescale i.MX8DXL support.
- Qualcomm SM8250 support.
- Renesas R8A7742 SH-PFC support.
Driver improvements:
- Severe cleanup and modernization of the MCP23s08 driver.
- Mediatek driver modularized.
- Setting config supported in the Meson driver.
- Wakeup support for the Broadcom BCM7211.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAl7dZC4ACgkQQRCzN7AZ
XXOEZg/9F4dCwXmMxMxbS1c7DSHxsJTEHYKDDgAZ0L36N2DHihpMGbVQFzEe9khK
xeSS8M4ecACYzw3FJGESaEC+fmTZ7zxr60SR++iyJJptooKAmcA00d2M/4VQ4ggN
P/nXFEsGJvQ7nNJSO95wXr5K8aVkQW7rjo1cnblXH0c9dYOp+ItyodIytKcdWeZ9
QfWSovYd+Oqra0braxx+pM/iTFVf6eOoCFZ8gkXB35pORsZ4Vl/e8pXMHXc3wUUm
S1b6e3fifLiEGANvCEXz47/f3lUmUY26FsCSCAt92tHChq/p6coIKKvKyP4723PF
R2L03iO8jMfsX+HwL2ivblSZ/lFExEgalWET56aogZClRQVynC0NMOnDEdluYGaT
XJZPib9sRqQOF36+G9Bcy4zlqjj1LoHwqpiCdAhtj3AACTKdoLjDK0sJ3Wn5E8lJ
QfIb+oqOmOGNHN/fdSsxsNM1ptOqNb/sW2Gk4O+X9tYzG17m16oZEVkrv4FNhmeC
mePl/7aX+aMoHkEYxvt9tF3kRDFbndcuHdNFtRxq0Tx9jELiR91ySjjs9bUr2Vnl
kkihtfIMZngQjBgHe2PNlcF2t7gSIgSBVEvwxslcUlx3XvVEDP16RKJV52aL80uu
ev4k0h72CTxI1lZuNuW4cJYDKF/wJPqPtQ8+GQfOZxG7yuM8tOc=
=3UGk
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.8 kernel cycle.
It's just really boring this time. Zero core changes. Just linear
development, cleanups and misc noncritical fixes. Some new drivers for
very new Qualcomm and Intel chips.
New drivers:
- Intel Jasper Lake support.
- NXP Freescale i.MX8DXL support.
- Qualcomm SM8250 support.
- Renesas R8A7742 SH-PFC support.
Driver improvements:
- Severe cleanup and modernization of the MCP23s08 driver.
- Mediatek driver modularized.
- Setting config supported in the Meson driver.
- Wakeup support for the Broadcom BCM7211"
* tag 'pinctrl-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: sprd: Fix the incorrect pull-up definition
pinctrl: pxa: pxa2xx: Remove 'pxa2xx_pinctrl_exit()' which is unused and broken
pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'
pinctrl: freescale: imx: Fix an error handling path in 'imx_pinctrl_probe()'
pinctrl: sirf: add missing put_device() call in sirfsoc_gpio_probe()
pinctrl: imxl: Fix an error handling path in 'imx1_pinctrl_core_probe()'
pinctrl: bcm2835: Add support for wake-up interrupts
pinctrl: bcm2835: Match BCM7211 compatible string
dt-bindings: pinctrl: Document optional BCM7211 wake-up interrupts
dt-bindings: pinctrl: Document 7211 compatible for brcm, bcm2835-gpio.txt
dt-bindings: pinctrl: stm32: Add missing interrupts property
pinctrl: at91-pio4: Add COMPILE_TEST support
pinctrl: Fix return value about devm_platform_ioremap_resource()
MAINTAINERS: Renesas Pin Controllers are supported
dt-bindings: pinctrl: ocelot: Add Sparx5 SoC support
pinctrl: ocelot: Fix GPIO interrupt decoding on Jaguar2
pinctrl: ocelot: Remove instance number from pin functions
pinctrl: ocelot: Always register GPIO driver
dt-bindings: pinctrl: rockchip: update example
pinctrl: amd: Add ACPI dependency
...
Wakeup capable GPIO IRQs routed via PDC are not being migrated when a CPU
is hotplugged. Add affinity callbacks to msmgpio IRQ chip to update the
affinity of wakeup capable IRQs.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
[mkshah: updated commit text and minor code fixes]
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1588314617-4556-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix a typo in the readl/writel accessor conversion where val is used
instead of pol changing the behavior of the original code.
Cc: stable@vger.kernel.org
Fixes: 6c73698904 pinctrl: qcom: Introduce readl/writel accessors
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200414003726.25347-1-ansuelsmth@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are no core changes this time, only driver developments.
- New driver for the Dialog Semiconductor DA9062 Power Management
Integrated Circuit (PMIC).
- Renesas SH-PFC has improved consistency, with group and
register checks in the configuration checker.
- New subdriver for the Qualcomm IPQ6018.
- Add the RGMII pin control functionality to Qualcomm IPQ8064.
- Performance and code quality cleanups in the Mediatek
driver.
- Improve the Broadcom BCM2835 support to cover all the GPIOs
that exist in it.
- The Allwinner/Sunxi driver properly masks non-wakeup IRQs on
suspend.
- Add some missing groups and functions to the Ingenic driver.
- Convert some of the Freescale device tree bindings to use the
new and all improved JSON YAML markup.
- Refactorings and support for the SFIO/GPIO in the Tegra194
SoC driver.
- Support high impedance mode in the Spreadtrum/Unisoc driver.
-----BEGIN PGP SIGNATURE-----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=1ZKq
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.7 kernel cycle.
There are no core changes this time, only driver developments:
- New driver for the Dialog Semiconductor DA9062 Power Management
Integrated Circuit (PMIC).
- Renesas SH-PFC has improved consistency, with group and register
checks in the configuration checker.
- New subdriver for the Qualcomm IPQ6018.
- Add the RGMII pin control functionality to Qualcomm IPQ8064.
- Performance and code quality cleanups in the Mediatek driver.
- Improve the Broadcom BCM2835 support to cover all the GPIOs that
exist in it.
- The Allwinner/Sunxi driver properly masks non-wakeup IRQs on
suspend.
- Add some missing groups and functions to the Ingenic driver.
- Convert some of the Freescale device tree bindings to use the new
and all improved JSON YAML markup.
- Refactorings and support for the SFIO/GPIO in the Tegra194 SoC
driver.
- Support high impedance mode in the Spreadtrum/Unisoc driver"
* tag 'pinctrl-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (64 commits)
pinctrl: qcom: fix compilation error
pinctrl: qcom: use scm_call to route GPIO irq to Apps
pinctrl: sprd: Add pin high impedance mode support
pinctrl: sprd: Use the correct pin output configuration
pinctrl: tegra: Add SFIO/GPIO programming on Tegra194
pinctrl: tegra: Renumber the GG.0 and GG.1 pins
pinctrl: tegra: Do not add default pin range on Tegra194
pinctrl: tegra: Pass struct tegra_pmx for pin range check
pinctrl: tegra: Fix "Scmitt" -> "Schmitt" typo
pinctrl: tegra: Fix whitespace issues for improved readability
pinctrl: mediatek: Use scnprintf() for avoiding potential buffer overflow
pinctrl: freescale: drop the dependency on ARM64 for i.MX8M
Revert "pinctrl: mvebu: armada-37xx: use use platform api"
dt-bindings: pinctrl: at91: Fix a typo ("descibe")
pinctrl: meson: add tsin pinctrl for meson gxbb/gxl/gxm
pinctrl: sprd: Fix the kconfig warning
pinctrl: ingenic: add hdmi-ddc pin control group
pinctrl: sirf/atlas7: Replace zero-length array with flexible-array member
pinctrl: sprd: Allow the SPRD pinctrl driver building into a module
pinctrl: Export some needed symbols at module load time
...
pinctrl: qcom: use scm_call to route GPIO irq to Apps has a typo in the
patch and introduced a compilation error.
Fixes: 13bec8d4 pinctrl: qcom: use scm_call to route GPIO irq to Apps
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20200331134603.13513-1-ansuelsmth@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For IPQ806x targets, TZ protects the registers that are used to
configure the routing of interrupts to a target processor.
To resolve this, this patch uses scm call to route GPIO interrupts
to application processor. Also the scm call interface is changed.
Signed-off-by: Ajay Kishore <akisho@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20200327223209.20409-1-ansuelsmth@gmail.com
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The hierarchical parts of MSM pinctrl/GPIO is only
used when the device tree has a "wakeup-parent" as
a phandle, but the .irq_eoi is anyway assigned leading
to semantic problems on elder Qualcomm chipsets.
When the drivers/mfd/qcom-pm8xxx.c driver calls
chained_irq_exit() that call will in turn call chip->irq_eoi()
which is set to irq_chip_eoi_parent() by default on a
hierachical IRQ chip, and the parent is pinctrl-msm.c
so that will in turn unconditionally call
irq_chip_eoi_parent() again, but its parent is invalid
so we get the following crash:
Unnable to handle kernel NULL pointer dereference at
virtual address 00000010
pgd = (ptrval)
[00000010] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
(...)
PC is at irq_chip_eoi_parent+0x4/0x10
LR is at pm8xxx_irq_handler+0x1b4/0x2d8
If we solve this crash by avoiding to call up to
irq_chip_eoi_parent(), the machine will hang and get
reset by the watchdog, because of semantic issues,
probably inside irq_chip.
As a solution, just assign the .irq_eoi conditionally if
we are actually using a wakeup parent.
Cc: David Heidelberg <david@ixit.cz>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: stable@vger.kernel.org
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Link: https://lore.kernel.org/r/20200306121221.1231296-1-linus.walleij@linaro.org
Link: https://lore.kernel.org/r/20200309125207.571840-1-linus.walleij@linaro.org
Link: https://lore.kernel.org/r/20200309152604.585112-1-linus.walleij@linaro.org
Tested-by: David Heidelberg <david@ixit.cz>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are parsing SSBI gpios as fourcell fwspecs but they are
twocell. Probably a simple copy-and-paste bug.
Tested on the APQ8060 DragonBoard and after this ethernet
and MMC card detection works again.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable@vger.kernel.org
Reviewed-by: Brian Masney <masneyb@onstation.org>
Fixes: ae436fe810 ("pinctrl: ssbi-gpio: convert to hierarchical IRQ helpers in gpio core")
Link: https://lore.kernel.org/r/20200306143416.1476250-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use newly added GPIO defines GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT instead of using hard-coded 1 and 0.
Main benefit is to make it easier to see which values mean IN and which
OUT. As a side effect this helps GPIO framework to change the direction
defines to something else if ever needed.
Please note that return value from get_direction call on
pinctrl-axp209 driver was changed. Previously pinctrl-axp209 might have
returned value 2 for direction INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Link: https://lore.kernel.org/r/20200214135712.GA14557@localhost.localdomain
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we
got rid of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips
along with the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much
improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt
map is provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML
DT bindings schema. (A first user of this.)
-----BEGIN PGP SIGNATURE-----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=PnK5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes, nothing too exciting about
this.
Some changes hit arch/sh and arch/arm but are well isolated and
acknowledged by the respective arch maintainers.
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we got rid
of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips along with
the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt map is
provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML DT bindings
schema (a first user of this)"
* tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: madera: Remove extra blank line
pinctrl: qcom: Don't lock around irq_set_irq_wake()
pinctrl: mvebu: armada-37xx: use use platform api
gpio: Drop the chained IRQ handler assign function
pinctrl: freescale: Add i.MX8MP pinctrl driver support
dt-bindings: imx: Add pinctrl binding doc for i.MX8MP
pinctrl: tigerlake: Tiger Lake uses _HID enumeration
pinctrl: sunrisepoint: Add Coffee Lake-S ACPI ID
pinctrl: iproc: Use platform_get_irq_optional() to avoid error message
pinctrl: dt-bindings: Fix some errors in the lgm and pinmux schema
pinctrl: intel: Pass irqchip when adding gpiochip
pinctrl: intel: Add GPIO <-> pin mapping ranges via callback
pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output
pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
pinctrl: sh-pfc: Split R-Car H3 support in two independent drivers
pinctrl: artpec6: fix __iomem on reg in set
pinctrl: ingenic: Use devm_platform_ioremap_resource()
pinctrl: ingenic: Factorize irq_set_type function
pinctrl: ingenic: Remove duplicated ingenic_chip_info structures
...
Some gpio's parent irqdomain may not use the struct irq_fwspec as
argument, such as msi irqdomain. So rename the callback
populate_parent_fwspec() to populate_parent_alloc_arg() and make it
allocate and populate the specific struct which is needed by the
parent irqdomain.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200114082821.14015-3-haokexin@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pm8xxx_pinctrl_desc structure is only copied into another
structure, so make it const.
The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1577864614-5543-15-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pm8xxx_pinctrl_desc structure is only copied into another structure,
so make it const.
The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1577864614-5543-9-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The m_voc_groups is not declared outside of the
driver, so make it static to avoid the following
sparse wanrning:
drivers/pinctrl/qcom/pinctrl-msm8976.c:592:12: warning: symbol 'm_voc_groups' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20191218102804.2487374-1-ben.dooks@codethink.co.uk
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
on sc7180 we have cases where multiple functions from the same
qup instance share the same pin. This is true for qup02/04/11 and qup13.
Add new function names to distinguish which qup function to use.
The device tree files for this platform haven't landed in mainline yet,
so there aren't any users upstream who should break with this change
in function names, however, anyone using the devicetree files that were
posted on the lists and using these specific function names will need
to update their changes.
Reported-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/0101016ef36a9118-f2919277-effa-4cd5-adf8-bbc8016f31df-000000@us-west-2.amazonses.com
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOs that can be configured as wakeup sources, have their
interrupt lines routed to PDC interrupt controller.
Provide the interrupt map of the GPIO to its wakeup capable
interrupt parent.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1572419178-5750-2-git-send-email-mkshah@codeaurora.org
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull irq updates from Ingo Molnar:
"Most of the IRQ subsystem changes in this cycle were irq-chip driver
updates:
- Qualcomm PDC wakeup interrupt support
- Layerscape external IRQ support
- Broadcom bcm7038 PM and wakeup support
- Ingenic driver cleanup and modernization
- GICv3 ITS preparation for GICv4.1 updates
- GICv4 fixes
There's also the series from Frederic Weisbecker that fixes memory
ordering bugs for the irq-work logic, whose primary fix is to turn
work->irq_work.flags into an atomic variable and then convert the
complex (and buggy) atomic_cmpxchg() loop in irq_work_claim() into a
much simpler atomic_fetch_or() call.
There are also various smaller cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
pinctrl/sdm845: Add PDC wakeup interrupt map for GPIOs
pinctrl/msm: Setup GPIO chip in hierarchy
irqchip/qcom-pdc: Add irqchip set/get state calls
irqchip/qcom-pdc: Add irqdomain for wakeup capable GPIOs
irqchip/qcom-pdc: Do not toggle IRQ_ENABLE during mask/unmask
irqchip/qcom-pdc: Update max PDC interrupts
of/irq: Document properties for wakeup interrupt parent
genirq: Introduce irq_chip_get/set_parent_state calls
irqdomain: Add bus token DOMAIN_BUS_WAKEUP
genirq: Fix function documentation of __irq_alloc_descs()
irq_work: Fix IRQ_WORK_BUSY bit clearing
irqchip/ti-sci-inta: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...))
irq_work: Slightly simplify IRQ_WORK_PENDING clearing
irq_work: Fix irq_work_claim() memory ordering
irq_work: Convert flags to atomic_t
irqchip: Ingenic: Add process for more than one irq at the same time.
irqchip: ingenic: Alloc generic chips from IRQ domain
irqchip: ingenic: Get virq number from IRQ domain
irqchip: ingenic: Error out if IRQ domain creation failed
irqchip: ingenic: Drop redundant irq_suspend / irq_resume functions
...
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/1574306382-32516-1-git-send-email-krzk@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIOs are marked as wakeup capable and are routed to another
interrupt controller that is an always-domain and can detect interrupts
even when most of the SoC is powered off. The wakeup interrupt
controller wakes up the GIC and replays the interrupt at the GIC.
Setup the TLMM irqchip in hierarchy with the wakeup interrupt controller
and ensure the wakeup GPIOs are handled correctly.
Co-developed-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-9-git-send-email-ilina@codeaurora.org
----
Changes in v2:
- Address review comments
- Fix Co-developed-by tag
Changes in v1:
- Address minor review comments
- Remove redundant call to set irq handler
- Move irq_domain_qcom_handle_wakeup() to this patch
Changes in RFC v2:
- Rebase on top of GPIO hierarchy support in linux-next
- Set the chained irq handler for summary line
The PM8950 features 8 GPIOs with hole in 3 and PMI8950 has
only two; these PMICs are totally compatible with this driver.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20191031103507.30678-2-kholk11@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SDC_QDSD_PINGROUP/UFS_RESET macros are missing the .tile info needed to
calculate the right register offsets. Adding them here and also
adjusting the offsets accordingly.
Fixes: f2ae04c45b ("pinctrl: qcom: Add SC7180 pinctrl driver")
Reported-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/20191021141507.24066-1-rnayak@codeaurora.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pinctrl driver to support pin configuration with the
pinctrl framework on MSM8976, MSM8956, APQ8056, APQ8076.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20191005105936.31216-2-kholk11@gmail.com
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the PM6150 and PM6150L GPIO support to the
Qualcomm PMIC GPIO binding.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Link: https://lore.kernel.org/r/1570188039-22122-1-git-send-email-kgunda@codeaurora.org
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the GPIO core has support for hierarchical IRQ chips, convert
Qualcomm's ssbi-gpio over to use these new helpers to reduce duplicated
code across drivers.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Link: https://lore.kernel.org/r/20190914111010.24384-1-masneyb@onstation.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to
the Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver.
-----BEGIN PGP SIGNATURE-----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=2nNz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
The UFS_RESET pin is the magical pin #150 now, not 153 per the
sdm845_groups array declared in this file. Fix the order of pins so that
UFS_RESET is 150 and the SDC pins follow after.
Fixes: 53a5372ce3 ("pinctrl: qcom: sdm845: Expose ufs_reset as gpio")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190830060227.12792-1-swboyd@chromium.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After we switched the two drivers that have .need_valid_mask
set to use the callback for setting up the .valid_mask,
we can just use the presence of the .init_valid_mask()
callback (or the OF reserved ranges, nota bene) to determine
whether to allocate the mask or not and we can drop the
.need_valid_mask field altogether.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190819093058.10863-1-linus.walleij@linaro.org
It is more helpful for drivers to have the affected fields
directly available when we use the callback to set up the
valid mask. Change this and switch over the only user
(MSM) to use the passed parameters. If we do this we can
also move the mask out of publicly visible struct fields.
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190819084904.30027-1-linus.walleij@linaro.or
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the GPIO core has support for hierarchical IRQ chips, convert
Qualcomm's spmi-gpio over to use these new helpers to reduce duplicated
code across drivers.
This change was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190808123242.5359-3-linus.walleij@linaro.org
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-34-swboyd@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When fall-through warnings was enabled by default the following warnings
was starting to show up:
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c: In function ‘pmic_gpio_populate’:
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c:815:20: warning: this statement may fall
through [-Wimplicit-fallthrough=]
pad->have_buffer = true;
~~~~~~~~~~~~~~~~~^~~~~~
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c:816:2: note: here
case PMIC_GPIO_SUBTYPE_GPIOC_4CH:
^~~~
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c:820:20: warning: this statement may fall
through [-Wimplicit-fallthrough=]
pad->have_buffer = true;
~~~~~~~~~~~~~~~~~^~~~~~
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c:821:2: note: here
case PMIC_GPIO_SUBTYPE_GPIOC_8CH:
^~~~
Rework so that the compiler doesn't warn about fall-through.
Fixes: d93512ef0f0e ("Makefile: Globally enable fall-through warning")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20190726112816.19723-1-anders.roxell@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
TSIF is the Transport Stream Interface.
First, rename tsif1 to tsif0, and tsif2 to tsif1.
Then squash all 5 tsif0 pins into a single function.
Same for tsif1.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Link: https://lore.kernel.org/r/503b2ae8-ead6-70cd-7b21-ce5f5166a23a@free.fr
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Lina Iyer <ilina@codeaurora.org>
Link: https://lore.kernel.org/r/20190724083828.7496-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAl0oTPcACgkQQRCzN7AZ
XXNTsw//aNPfkJS8gRszv58G56lyuO8h6Cq4m5eDpzhlpjx5qjELgi9h2UNGINqD
7CWxo35ufbKe0fDIcqpXmtuDMtSu6MuKT3SMepuw9uf9wxyndK4RIuyb0lpAJrx2
+NMPxzS+ARlrMmcfvXPRyPWHqAkXsQk6zcCgiuNCPtROkOZgs1YZ3+pemZw2/FMq
gSLTO/95p0TPWr6YAlpByqfsA1A/onEm9HOiU2INV7DrAfUj7mnkuC1nZ4IJDFcv
Gn6qQVQPah+MBzkwt4WXy5kDRozCIbg7x+FQBw3KAO23TrLDTFuNsYIWGFcP2CN2
eT8iSP3cWrXNUuEgcPD59aO07rhFooT+QBQFt2ih1dJCV1u/795wb57nxSh1YDcO
M2tG+AW2EZky65FXwhLW2rq3LvmTM4kiEz3mA/DrcOAKvvQllK+6FKEhNy0StstP
yvvlqoXdgH3sfOnWTAyHr35qA/pMuGEXSryWTJPqpflCvZ3wxNk+IV5nyPAtfaFz
CK7U0Ya7NaEp/5ZlpE720apJ4uSqmRrLwk5Y1eKQvT46mGOk3rC9ZPIMXc8mB10/
mJ9mTubi1t4uIPnBl/T1T7f8QhNtr9hOY6wjLf1LoMeJ1XVNBqA+2uydOlBJ1iop
RQ7y/Jl1SZ/gBzKCmvjPHT2+0Oui9oXGd9bQi0xQKO5Lus/nAIg=
=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
Add initial pinctrl driver to support pin configuration with
pinctrl framework for SM8150
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Isaac J. Manjarres <isaacm@codeaurora.org>
[vkoul: modify to use upstream tile support
use upstream code style
order the functions and squash functions]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190702105045.27646-4-vkoul@kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce the irq_enable callback which will be same as irq_unmask
except that it will also clear the status bit before unmask.
This will help in clearing any erroneous interrupts that would
have got latched when the interrupt is not in use.
There may be devices like UART which can use the same gpio line
for data rx as well as a wakeup gpio when in suspend. The data that
was flowing on the line may latch the interrupt and when we enable
the interrupt before going to suspend, this would trigger the
unexpected interrupt. This change helps clearing the interrupt
so that these unexpected interrupts gets cleared.
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Link: https://lore.kernel.org/r/1561472086-23360-1-git-send-email-neeraju@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clang warns when CONFIG_ACPI is unset:
drivers/pinctrl/qcom/pinctrl-sdm845.c:1320:5: warning: 'CONFIG_ACPI' is
not defined, evaluates to 0 [-Wundef]
#if CONFIG_ACPI
^
1 warning generated.
Use ifdef instead of if to resolve this.
Fixes: a229105d7a ("pinctrl: qcom: sdm845: Provide ACPI support")
Link: https://github.com/ClangBuiltLinux/linux/issues/569
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch provides basic support for booting with ACPI instead
of the currently supported Device Tree. When doing so there are a
couple of differences which we need to taken into consideration.
Firstly, the SDM850 ACPI tables omit information pertaining to the
4 reserved GPIOs on the platform. If Linux attempts to touch/
initialise any of these lines, the firmware will restart the
platform.
Secondly, when booting with ACPI, it is expected that the firmware
will set-up things like; Regulators, Clocks, Pin Functions, etc in
their ideal configuration. Thus, the possible Pin Functions
available to this platform are not advertised when providing the
higher GPIOD/Pinctrl APIs with pin information.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When booting MSM based platforms with Device Tree or some ACPI
implementations, it is possible to provide a list of reserved pins
via the 'gpio-reserved-ranges' and 'gpios' properties respectively.
However some ACPI tables are not populated with this information,
thus it has to come from a knowledgable device driver instead.
Here we provide the MSM common driver with additional support to
parse this informtion and correctly populate the widely used
'valid_mask'.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ufs_reset pin is expected to be wired to the reset pin of the
primary UFS memory but is pretty much just a general purpose output pinr
Reorder the pins and expose it as gpio 150, so that the UFS driver can
toggle it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJchil8AAoJEEEQszewGV1zTCcP/AurT3InBO4nVdN9UMuoDL7P
gx3SALULapc4+M1NUoRw+w+z5fvjd0gGdPXZeyhX1E9kXxLmWBmBf6tl0MO2YYPC
UWbSnBaWIOOli0f4k+GKVF8LKqD0z0e/YqX4mG7UI3OLJzcJgm7OL9uXN3Gh7tIP
Pa6CGbv0aRDkZpWUD2ZTpSPCRYGT57roVq//d7V7s+0lveS97pQuMv43YlS5L2my
JOOhHNG33bgi4lS/ZOP81G16oOrVaoupXuX7E+AvgG6vxr5965Fi+qoGLkxIuYOm
jtrzuNY98eL2m9b505VYdNmD7ouBhG6CKFb4njpOvjkkqNUXOaGV53wlEuEYRUNz
bsp0596+dlOcW7wl11r6YI4Kyn2wQJFql1AwS8A4dEtbuboGrDy16N3adr1SkIGZ
4ESN8xydcC7CAgUGXks+AgDj9vYwOs4apylJDW5tMk4K0LIsEYsDkbNeS9hwDYIH
ZlbQe9N2loB6qQbX3c3D3/sIhKj2VB4elONSwOW10M8OJdJwp8h44UyMZ3TIEHIT
7Gu9pw5vobXbccKCSjqkYYflaHMmjwZUtLqDZws818sbe/xgDxONbRqloZCLV39Y
kmwRGbbE5WtNAM0X+ABwMG3Lm77wxCFKCjJwLHH79qqt4kSBynEKXQ4D/coG/Hln
6idanzKEPiIBJ+6QLdbQ
=EfXK
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is a calm cycle, not much happened this time around: not even
much incremental development. Some three new drivers, that is all.
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements"
* tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (70 commits)
pinctrl: imx: fix scu link errors
dt-bindings: pinctrl: Document the i.MX50 IOMUXC binding
pinctrl: qcom: spmi-gpio: Reorder debug print
pinctrl: nomadik: fix possible object reference leak
pinctrl: stm32: return error upon hwspinlock failure
pinctrl: stm32: fix memory leak issue
pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions
pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions
pinctrl: sh-pfc: Validate fixed-size field widths at build time
pinctrl: sh-pfc: sh73a0: Fix fsic_spdif pin groups
pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group
pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group
pinctrl: sh-pfc: emev2: Add missing pinmux functions
pinctrl: sunxi: Support I/O bias voltage setting on A80
pinctrl: ingenic: Add LCD pins for the JZ4725B SoC
pinctrl: samsung: Remove legacy API for handling external wakeup interrupts mask
pinctrl: bcm2835: Direct GPIO config changes to generic pinctrl
pinctrl: bcm2835: declare pin config as generic
pinctrl: qcom: qcs404: Drop unused UFS_RESET macro
dt-bindings: add documentation for slew rate
...
Core changes:
- The big change this time around is the irqchip handling in
the qualcomm pin controllers, closely coupled with the
gpiochip. This rework, in a classic fall-between-the-chairs
fashion has been sidestepped for too long. The Qualcomm
IRQchips using the SPMI and SSBI transport mechanisms have
been rewritten to use hierarchical irqchip. This creates
the base from which I intend to gradually pull support for
hierarchical irqchips into the gpiolib irqchip helpers to
cut down on duplicate code. We have too many hacks in the
kernel because people have been working around the missing
hierarchical irqchip for years, and once it was there,
noone understood it for a while. We are now slowly adapting
to using it. This is why this pull requests include changes
to MFD, SPMI, IRQchip core and some ARM Device Trees
pertaining to the Qualcomm chip family. Since Qualcomm have
so many chips and such large deployments it is paramount
that this platform gets this right, and now it (hopefully)
does.
- Core support for pull-up and pull-down configuration, also
from the device tree. When a simple GPIO chip support a
"off or on" pull-up or pull-down resistor, we provide a
way to set this up using machine descriptors or device tree.
If more elaborate control of pull up/down (such as
resistance shunt setting) is required, drivers should be
phased over to use pin control. We do not yet provide a
userspace ABI for this pull up-down setting but I suspect
the makers are going to ask for it soon enough. PCA953x
is the first user of this new API.
- The GPIO mockup driver has been revamped after some
discussion improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for
both testing and virtual prototyping, e.g. when you do
not yet have a GPIO expander to play with but really
want to get something to develop code around before
hardware is available. It's neat. The blackbox testing
usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating
flags.
- A new device core helper for devm_platform_ioremap_resource()
is funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped
I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum
driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcgoLEAAoJEEEQszewGV1zjBAP/3OmTFGv49PFmJwSx+PlLiYf
V6/UPaQzq81CGSMtHxbS51TyP9Id7PCfsacbuFYutzn0D1efvl7jrkb8qJ6fVvCM
bl/i6q8ipRTPzAf1hD3QCgCe3BXCA064/OcPrz987oIvI3bJQXsmBjBSXHWr4Cwa
WfB5DX/afn9TK3XHhMQGfw5f0d+TtnKAs90RTTVKiz9Ow8eFYZJOhgPkvhCR3Gi9
YJIzIAiwhHZ7/zauo4JAYFU/O/Z3YEC5zeLne2ItebzNooRkSxdz0c9Hs7HlCZmU
930Uv9jNN89N3vPqpZzAHtPvwDOmAILMWvKy9xRSp+eoIukarRJgF7ALPk7QWxK1
yy+tGj4dXBQ6tI8W3wUN1WgjNpii3K1HbJ+1LQVQL2/q9o+3YXXqmjdjuw7C8YYV
5ystNrUppkgfIIciHL4lhqw3wKJJhVEAns2V245hIitoShT+RvIg8GQbGZmWlQFd
YsHbynqHL9iwfRNv26kEqZXZOo/4D1t6Scw+OPVyba2Wyttf+qbmg+XaYMqFaxYW
mfydvdtymeCOUIPJMzw58KGPUTXJ4UPLENyayXNUHokr1a8VO8OIthY7zwi0CpvJ
IcsAY9zoGxvfbRV922mlIsw3oOBcM2IN2lC9sY469ZVnjBrdC3rsQpIBZr+Vzz8i
YlUfXLSGSyuUZUz//2eG
=VoVC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.1 cycle:
Core changes:
- The big change this time around is the irqchip handling in the
qualcomm pin controllers, closely coupled with the gpiochip. This
rework, in a classic fall-between-the-chairs fashion has been
sidestepped for too long.
The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms
have been rewritten to use hierarchical irqchip. This creates the
base from which I intend to gradually pull support for hierarchical
irqchips into the gpiolib irqchip helpers to cut down on duplicate
code.
We have too many hacks in the kernel because people have been
working around the missing hierarchical irqchip for years, and once
it was there, noone understood it for a while. We are now slowly
adapting to using it.
This is why this pull requests include changes to MFD, SPMI,
IRQchip core and some ARM Device Trees pertaining to the Qualcomm
chip family. Since Qualcomm have so many chips and such large
deployments it is paramount that this platform gets this right, and
now it (hopefully) does.
- Core support for pull-up and pull-down configuration, also from the
device tree. When a simple GPIO chip supports an "off or on" pull-up
or pull-down resistor, we provide a way to set this up using
machine descriptors or device tree.
If more elaborate control of pull up/down (such as resistance shunt
setting) is required, drivers should be phased over to use pin
control. We do not yet provide a userspace ABI for this pull
up-down setting but I suspect the makers are going to ask for it
soon enough. PCA953x is the first user of this new API.
- The GPIO mockup driver has been revamped after some discussion
improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for both testing
and virtual prototyping, e.g. when you do not yet have a GPIO
expander to play with but really want to get something to develop
code around before hardware is available. It's neat. The blackbox
testing usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating flags.
- A new device core helper for devm_platform_ioremap_resource() is
funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers"
* tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits)
gpio: gpio-omap: fix level interrupt idling
gpio: amd-fch: Set proper output level for direction_output
x86: apuv2: remove unused variable
gpio: pca953x: Use PCA_LATCH_INT
platform/x86: fix PCENGINES_APU2 Kconfig warning
gpio: pca953x: Fix dereference of irq data in shutdown
gpio: amd-fch: Fix type error found by sparse
gpio: amd-fch: Drop const from resource
gpio: mxc: add check to return defer probe if clock tree NOT ready
gpio: ftgpio: Register per-instance irqchip
gpio: ixp4xx: Add DT bindings
x86: pcengines apuv2 gpio/leds/keys platform driver
gpio: AMD G-Series PCH gpio driver
drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource()
gpio: tqmx86: Set proper output level for direction_output
gpio: sprd: Change to use SoC compatible string
gpio: sprd: Use SoC compatible string instead of wildcard string
gpio: of: Handle both enable-gpio{,s}
gpio: of: Restrict enable-gpio quirk to regulator-gpio
gpio: davinci: use devm_platform_ioremap_resource()
...
It's reasonable to expect that people turn to the "gpio" debugfs file to
first and foremost learn about the direction and value of a gpio, and
second to that about it's pinconf. So reorder the value so each line
reads:
gpioN: direction value ...
This also makes it consistent with the TLMM pinctrl driver's output in
the same dump.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SSBI GPIOs are numbered 1..ngpio, so the boundary check in
pm8xxx_domain_translate() is off by one. This patch corrects that check.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ssbi-gpio did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should
be usable from the start without the consumer having to make an
additional call to get the proper IRQ on the parent. This patch adds
hierarchical IRQ chip support to the ssbi-gpio code to correct this
issue.
The constant PM8XXX_GPIO_PHYSICAL_OFFSET is introduced to replace the
hardcoded '1' that previously existed in two places in this driver to
improve code readability.
This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The probing of this driver calls platform_irq_count, which will
setup all of the IRQs that are configured in device tree. In
preparation for converting this driver to be a hierarchical IRQ
chip, hardcode the IRQ count based on the hardware type so that all
the IRQs are not configured immediately and are configured on an
as-needed basis later in the boot process. This change will also
allow for the removal of the interrupts property later in this
patch series once the hierarchical IRQ chip support is in.
This patch also removes the generic qcom,ssbi-gpio OF match since we
don't know the number of pins. All of the existing upstream bindings
already include the more-specific binding.
This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOs on the SPMI PMIC are numbered 1..ngpio, so the boundary check in
pmic_gpio_domain_translate() is off by one, correct this.
Fixes: ca69e2d165 ("qcom: spmi-gpio: add support for hierarchical IRQ chip")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SDC controls live in the south tile, not the north one. Correct this
so that we program the right registers.
Cc: stable@vger.kernel.org
Fixes: 22eb8301db ("pinctrl: qcom: Add qcs404 pinctrl driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The UFS_RESET macro serves no purpose on QCS404, remove it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Select IRQ_DOMAIN_HIERARCHY for spmi-gpio in Kconfig since this driver
is now setup as a hierarchical IRQ chip.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
spmi-gpio did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should
be usable from the start without the consumer having to make an
additional call to get the proper IRQ on the parent. This patch adds
hierarchical IRQ chip support to the spmi-gpio code to correct this
issue.
Driver was tested using the volume buttons (via gpio-keys) on the LG
Nexus 5 (hammerhead) phone with the following two configurations.
volume-up {
interrupts-extended = <&pm8941_gpios 2 IRQ_TYPE_EDGE_BOTH>;
...
};
volume-up {
gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
...
};
Both configurations now show that spmi-gpio is the IRQ domain and that
the IRQ is setup in a hierarchy.
$ grep volume_up /proc/interrupts
72: 6 0 spmi-gpio 1 Edge volume_up
$ cat /sys/kernel/debug/irq/irqs/72
handler: handle_edge_irq
device: (null)
status: 0x00000403
_IRQ_NOPROBE
istate: 0x00000000
ddepth: 0
wdepth: 0
dstate: 0x02400203
IRQ_TYPE_EDGE_RISING
IRQ_TYPE_EDGE_FALLING
IRQD_ACTIVATED
IRQD_IRQ_STARTED
node: 0
affinity: 0-3
effectiv:
domain: :soc:spmi@fc4cf000:pm8941@0:gpios@c000
hwirq: 0x1
chip: spmi-gpio
flags: 0x4
IRQCHIP_MASK_ON_SUSPEND
parent:
domain: :soc:spmi@fc4cf000
hwirq: 0xc100057
chip: pmic_arb
flags: 0x4
IRQCHIP_MASK_ON_SUSPEND
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
