While looking at the X1E PDC GPIO interrupts it became clear that we're
lacking a convenient and accessible way to validate if the TLMM
interrupt code performing as expected.
This introduces a kunit-based "hack" that relies on pin bias/pull
configuration to tickle the interrupt logic in non-connected pins to
allow us to evaluate that an expected number of interrupts are
delivered.
The bias/pull configuration is done with mmio accesses directly from the
test code, to avoid having to programmatically acquire and drive the
pinconf interface for the test pin. This limits the scalability of the
code to targets with a particular register layout, but serves our needs
for now.
The pin to be used for testing is specified by the tester using the
"tlmm-test.gpio" module parameter.
Worth mentioning is that some of the test cases currently fails for
GPIOs that is not backed by PDC (i.e. "non-wakeup" GPIOs), as lingering
latched interrupt state is being delivered at IRQ request time.
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/20250227-tlmm-test-v1-1-d18877b4a5db@oss.qualcomm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is based on MSM8916 driver with the pinctrl definitions from
Qualcomm's downstream MSM8917 driver.
Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/20241215-msm8917-v9-3-bacaa26f3eef@mainlining.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add driver for the pincontrol device as present on the Qualcomm
SAR2130P platform. This is based on the msm-5.10 tree, tag
KERNEL.PLATFORM.1.0.r4-00400-NEO.0.
Co-developed-by: Mayank Grover <groverm@codeaurora.org>
Signed-off-by: Mayank Grover <groverm@codeaurora.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/20241018-sar2130p-tlmm-v2-2-11a1d09a6e5f@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IPQ5424 SoC comes with a TLMM block, like all other Qualcomm
platforms, so add a driver for it.
Co-developed-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Link: https://lore.kernel.org/20240927065244.3024604-6-quic_srichara@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the pin controller block on SM4250 Low Power Island.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/20240612-sm4250-lpi-v4-2-a0342e47e21b@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver for TLMM block found in SM4450 SoC.
Can Guo helped out in reviewing the driver.
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Tengfei Fan <quic_tengfan@quicinc.com>
Link: https://lore.kernel.org/r/20231212094900.12615-3-quic_tengfan@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial pinctrl driver to support pin configuration with pinctrl
framework for X1E80100 SoC.
Co-developed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231117093921.31968-3-quic_sibis@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add driver for the pin controller in Low Power Audio SubSystem (LPASS)
of Qualcomm SM8650 SoC.
Notable differences against SM8550 LPASS pin controller:
1. Additional address space for slew rate thus driver uses
LPI_FLAG_SLEW_RATE_SAME_REG and sets slew rate via different
register.
2. Two new pin mux functions: qca_swr_clk and qca_swr_data
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231027093615.140656-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the pin controller block on SM6115's Low Power Island.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230722-topic-6115_lpasstlmm-v2-2-d4883831a858@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Add driver for pin controller in Low Power Audio SubSystem (LPASS). The
driver is similar to SM8250 LPASS pin controller, with difference in one
new pin (gpio14) belonging to swr_tx_data.
Link: https://lore.kernel.org/r/20230719192058.433517-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The IPQ5332 SoC comes with a TLMM block, like all other Qualcomm
platforms, so add a driver for it.
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206071217.29313-3-quic_kathirav@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add druver for pin controller in Low Power Audio SubSystem (LPASS). The
driver is similar to SM8450 LPASS pin controller, with differences in
few pin groups (qua_mi2s -> i2s0).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230203174645.597053-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for Lemans TLMM configuration and control via the pinctrl
framework.
Signed-off-by: Yadu MG <quic_ymg@quicinc.com>
Signed-off-by: Prasad Sodagudi <quic_psodagud@quicinc.com>
[Bartosz: made the driver ready for upstream]
Co-developed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230201150011.200613-3-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver for TLMM block found in SM8550 SoC.
Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221230203637.2539900-3-abel.vesa@linaro.org
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pin control driver for the TLMM block found in the QDU1000
and QRU1000 SoC.
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221216230852.21691-3-quic_molvera@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Snapdragon 670 has a Top-Level Mode Multiplexer (TLMM) for various
features. Add a driver to support it.
Link: de5a12173c%5E%21/#F6
Link: 04f083156d%5E%21/#F22
Link: 54837652e3%5E%21/#F0
Link: f0409b0717%5E%21/#F0
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221014001934.4995-4-mailingradian@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver to support pin configuration for LPASS
(Low Power Audio SubSystem) LPI (Low Power Island) pinctrl
on SC8280XP.
This IP is an additional pin control block for Audio Pins on top the
existing SoC Top level pin-controller.
Hardware setup looks like:
TLMM GPIO[189 - 207] --> LPASS LPI GPIO [0 - 18]
This pin controller has some similarities compared to Top level
msm SoC Pin controller like 'each pin belongs to a single group'
and so on. However this one is intended to control only audio
pins in particular, which can not be configured/touched by the
Top level SoC pin controller except setting them as gpios.
Apart from this, slew rate is also available in this block for
certain pins which are connected to SLIMbus or SoundWire Bus.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220817113747.9111-3-srinivas.kandagatla@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver to support pin configuration for LPASS
(Low Power Audio SubSystem) LPI (Low Power Island) pinctrl
on SM8450.
This IP is an additional pin control block for Audio Pins on top the
existing SoC Top level pin-controller.
Hardware setup looks like:
TLMM GPIO[165 - 187] --> LPASS LPI GPIO [0 - 22]
This pin controller has some similarities compared to Top level
msm SoC Pin controller like 'each pin belongs to a single group'
and so on. However this one is intended to control only audio
pins in particular, which can not be configured/touched by the
Top level SoC pin controller except setting them as gpios.
Apart from this, slew rate is also available in this block for
certain pins which are connected to SLIMbus or SoundWire Bus.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220817113833.9625-3-srinivas.kandagatla@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a driver to control the TLMM block on SM6375. This is an adapted
version of msm-5.4's pinctrl-blair driver.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20220716192900.454653-2-konrad.dybcio@somainline.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Extract the chip specific SM8250 data from the LPASS LPI pinctrl driver
to allow reusing the common code in the addition of subsequent
platforms.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1650285427-19752-6-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pincontrol driver for tlmm block found in SM8450 SoC
This patch is based on initial code downstream by
Elliot Berman <eberman@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211201072434.3968768-3-vkoul@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's a porting of pinctrl-scuba driver from CAF msm-4.19 kernel. The
egpio and wake bits are removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923033224.29719-3-shawn.guo@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pincontrol driver for tlmm block found in SM6350 SoC
This patch is based on downstream copyleft code.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923161450.15278-2-konrad.dybcio@somainline.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on CAF implementation with egpio/wake_reg support removed.
Similar function names were merged to reduce total number of functions.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210723192352.546902-3-iskren.chernev@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver for the sc8180x TLMM block.
A noteworthy difference from previous TLMM blocks is that the registers
for GPIO 177 through 189 are for some reason offset from the typical
layout. Other than that the driver is same old...
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210126042650.1725176-3-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pincontrol driver for tlmm block found in SM8350 SoC
This patch is based on initial code downstream by Raghavendra.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210205140132.274242-3-vkoul@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial pinctrl driver to support pin configuration for
LPASS (Low Power Audio SubSystem) LPI (Low Power Island) pinctrl
on SM8250.
This IP is an additional pin control block for Audio Pins on top the
existing SoC Top level pin-controller.
Hardware setup looks like:
TLMM GPIO[146 - 159] --> LPASS LPI GPIO [0 - 13]
This pin controller has some similarities compared to Top level
msm SoC Pin controller like 'each pin belongs to a single group'
and so on. However this one is intended to control only audio
pins in particular, which can not be configured/touched by the
Top level SoC pin controller except setting them as gpios.
Apart from this, slew rate is also available in this block for
certain pins which are connected to SLIMbus or SoundWire Bus.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201202163443.26499-3-srinivas.kandagatla@linaro.org
[Add some dependencies]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial Qualcomm msm8226 pinctrl driver to support pin configuration
with pinctrl framework for msm8226 SoC.
- Initial formatting and style was taken from the msm8x74 pinctrl driver
added by Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bartosz Dudziak <bartosz.dudziak@snejp.pl>
Link: https://lore.kernel.org/r/20200716205530.22910-3-bartosz.dudziak@snejp.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pinctrl driver to support pin configuration with the
pinctrl framework on MSM8976, MSM8956, APQ8056, APQ8076.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20191005105936.31216-2-kholk11@gmail.com
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
