Introduce Tx-Rx detection Time and Rx AEQ training mappings to
phy-airoha-pcie driver. This is a preliminary patch to introduce PCIe
support to En7581 SoC through the mediatek-gen3 PCIe driver.
This change is not introducing any backward compatibility issue since
the EN7581 dts is not upstream yet.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/edf3b28926177166c65256604d69f2f576cb6fb3.1719682943.git.lorenzo@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the Exynos USB 3.1 DRD combo phy, as found in Exynos 9
SoCs like Google GS101. It supports USB SS, HS and DisplayPort.
In terms of UTMI+, this is very similar to the existing Exynos850
support in this driver. The difference is that this combo phy supports
both UTMI+ (HS) and PIPE3 (SS). It also supports DP alt mode.
The number of ports for UTMI+ and PIPE3 can be determined using the
LINKPORT register (which also exists on Exynos E850).
For SuperSpeed (SS) a new SS phy is in use and its PIPE3 interface is
new compared to Exynos E850, and also very different from the existing
support for older Exynos SoCs in this driver.
The SS phy needs a bit more configuration work and register tuning for
signal quality to work reliably, presumably due to the higher
frequency, e.g. to account for different board layouts. Additionally,
power needs to be enabled before writing to the SS phy registers.
This commit adds the necessary changes for USB HS and SS to work.
DisplayPort is out of scope in this commit.
Notes:
* For the register tuning, exynos5_usbdrd_apply_phy_tunes() has been
added with the appropriate data structures to support tuning at
various stages during initialisation. Since these are hardware
specific, the platform data is supposed to be populated accordingly.
The implementation is loosely modelled after the Samsung UFS PHY
driver.
There is one tuning state for UTMI+, PTS_UTMI_POSTINIT, to execute
after init and generally intended for HS signal tuning, as done in
this commit.
PTS_PIPE3_PREINIT PTS_PIPE3_INIT PTS_PIPE3_POSTINIT
PTS_PIPE3_POSTLOCK are tuning states for PIPE3. In the downstream
driver, preinit differs by Exynos SoC, and postinit and postlock
are different per board. The latter haven't been implemented for
gs101 here, because downstream doesn't use them on gs101 either.
* Signal lock acquisition for SS depends on the orientation of the
USB-C plug. Since there currently is no infrastructure to chain
connector events to both the USB DWC3 driver and this phy driver, a
work-around has been added in
exynos5_usbdrd_usbdp_g2_v4_pma_check_cdr_lock() to check both
registers if it failed in one of the orientations.
* Equally, we can only establish SS speed in one of the connector
orientations due to programming differences when selecting the lane
mux in exynos5_usbdrd_usbdp_g2_v4_pma_lane_mux_sel(), which really
needs to be dynamic, based on the orientation of the connector.
* As is, we can establish a HS link using any cable, and an SS link in
one orientation of the plug, falling back to HS if the orientation is
reversed to the expectation.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-6-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using the regulator_bulk APIs, the handling of power supplies becomes
much simpler. There is no need anymore to check if regulators have been
acquired or not, the bulk APIs will do all the work for us. We can also
drop the various handles to the individual power supplies in the driver
runtime data and instead simply treat them all as one thing. Error
cleanup also becomes much simpler.
Converting to the regulator_bulk APIs also makes it easier to add
support for those SoCs that have additional power supplies for the PHY.
Google Tensor gs101 is one example of such a SoC. Otherwise we'd have
to add all additional supplies individually via individual calls to
regulator_get() and enable/disable handle them all individually,
including complicated error handling. That doesn't scale and clutters
the code.
Just update the code to use the regulator_bulk APIs.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-5-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for support for additional platforms, convert the phy
register access clock to using the clk_bulk interfaces.
Newer SoCs like Google Tensor gs101 require additional clocks for
access to additional (different) register areas (PHY, PMA, PCS), and
converting to clk_bulk simplifies addition of those extra clocks.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-4-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using the clk_bulk APIs, the clock handling for the core clocks becomes
much simpler. No need to check any flags whether or not certain clocks
exist or not. Further, we can drop the various handles to the
individual clocks in the driver data and instead simply treat them all
as one thing.
So far, this driver assumes that all platforms have a clock "ref". It
also assumes that the clocks "phy_pipe", "phy_utmi", and "itp" exist if
the platform data "has_common_clk_gate" is set to true. It then goes
and individually tries to acquire and enable and disable all the
individual clocks one by one. Rather than relying on these implicit
clocks and open-coding the clock handling, we can just explicitly spell
out the clock names in the different device data and use that
information to populate clk_bulk_data, allowing us to use the clk_bulk
APIs for managing the clocks.
As a side-effect, this change highlighted the fact that
exynos5_usbdrd_phy_power_on() forgot to check the result of the clock
enable calls. Using the clk_bulk APIs, the compiler now warns when
return values are not checked - therefore add the necessary check
instead of silently ignoring failures and continuing as if all is OK
when it isn't.
For consistency, also change a related dev_err() to dev_err_probe() in
exynos5_usbdrd_phy_clk_handle() to get consistent error message
formatting.
Finally, exynos5_usbdrd_phy_clk_handle() prints an error message in all
cases as necessary (except for -ENOMEM). There is no need to print
another message in its caller (the probe() function), and printing
errors during OOM conditions is usually discouraged. Drop the
duplicated message in exynos5_usbdrd_phy_probe().
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-3-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some versions of this IP have been integrated using separate PMU power
control registers for the HS and SS parts. One example is the Google
Tensor gs101 SoC.
Such SoCs can now set pmu_offset_usbdrd0_phy_ss in their
exynos5_usbdrd_phy_drvdata for the SS phy to the appropriate value.
The existing 'usbdrdphy' alias can not be used in this case because
that is meant for determining the correct PMU offset if multiple
distinct PHYs exist in the system (as opposed to one PHY with multiple
isolators).
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-2-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We actually want to calculate the alignment values first, then
use the alignment value to look up the data from reg_configs[].
Fixes: d3ab795533 ("phy: starfive: Add mipi dphy tx support")
Reviewed-by: Shengyang Chen <shengyang.chen@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Link: https://lore.kernel.org/r/20240627020059.163535-1-changhuang.liang@starfivetech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for printing some basic status information to debugfs. This
is helpful when debugging phy consumers to make sure they are configuring
the phy appropriately.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-6-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Take the phy mutex in xlate to protect against concurrent
modification/access to gtr_phy. This does not typically cause any
issues, since in most systems the phys are only xlated once and
thereafter accessed with the phy API (which takes the locks). However,
we are about to allow userspace to access phys for debugging, so it's
important to avoid any data races.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-5-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For PCIe and DisplayPort, the phy instance represents the controller's
logical lane. Wait for the instance 0 phy's PLL to lock as other
instances will never lock. We do this in xpsgtr_wait_pll_lock so callers
don't have to determine the correct lane themselves.
The original comment is wrong about cumulative wait times. Since we are
just polling a bit, all subsequent waiters will finish immediately.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-4-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The phy "type" is just the combination of protocol and instance, and is
never used apart from that. Store the instance directly, instead of
converting to a type first. No functional change intended.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-3-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Lanes can use other lanes' reference clocks, as determined by refclk.
Use refclk to determine the clock to enable/disable instead of always
using the lane's own reference clock. This ensures the clock selected in
xpsgtr_configure_pll is the one enabled.
For the other half of the equation, always program REF_CLK_SEL even when
we are selecting the lane's own clock. This ensures that Linux's idea of
the reference clock matches the hardware. We use the "local" clock mux
for this instead of going through the ref clock network.
Fixes: 25d7008335 ("phy: xilinx: phy-zynqmp: dynamic clock support for power-save")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-2-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
cdns_torrent_dp_set_power_state() does not consider that ret might be
overwritten. Add return value check of regmap_read_poll_timeout() after
register read in cdns_torrent_dp_set_power_state().
Fixes: 5b16a790f1 ("phy: cadence-torrent: Reorder few functions to remove function declarations")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240702032042.3993031-1-make24@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Compile testing configurations without REGMAP support enabled results in
a bunch of errors being reported:
../drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:569:21: error: variable ‘rk_hdptx_phy_regmap_config’ has initializer but incomplete type
569 | static const struct regmap_config rk_hdptx_phy_regmap_config = {
| ^~~~~~~~~~~~~
../drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:570:10: error: ‘const struct regmap_config’ has no member named ‘reg_bits’
570 | .reg_bits = 32,
| ^~~~~~~~
Note that selecting REGMAP alone is not enough, because of the following
liker error:
phy-rockchip-samsung-hdptx.c:(.text+0x10c): undefined reference to `__devm_regmap_init_mmio_clk'
Instead of the obvious fix to enable REGMAP_MMIO, select MFD_SYSCON,
which implicitly enables REGMAP_MMIO as well. The rationale is that the
driver has been already relying on the syscon functionality.
Moreover, without MFD_SYSCON enabled, the test coverage is reduced,
since the linker might not detect any potential undefined references
following syscon_regmap_lookup_by_phandle() invocation in
rk_hdptx_phy_probe() body. That is because the function would
unconditionally return -ENOTSUP, hence the compiler is free to optimize
out any unreachable code.
Finally ensure PHY_ROCKCHIP_SAMSUNG_HDPTX depends on HAS_IOMEM, as
required by MFD_SYSCON.
Fixes: 553be2830c ("phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240629-rk-hdptx-compile-test-fix-v1-1-c86675ba8070@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Introduce support for Airoha PCIe PHY controller available in EN7581
SoC.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Zhengping Zhang <zhengping.zhang@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20ac99aa8628d97778594f606681db7f868f24fe.1718485860.git.lorenzo@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In various configurations/architectures, bitfield.h may not be
transitively included, which results in a compiler error because
FIELD_PREP is an unexpanded macro:
drivers/phy/freescale/phy-fsl-imx8qm-hsio.c:459:8: error: call to undeclared function 'FIELD_PREP'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
459 | val = FIELD_PREP(HSIO_MODE_MASK, val);
| ^
1 error generated.
Include bitfield.h explicitly to fix the build.
Fixes: 82c56b6dd2 ("phy: freescale: imx8qm-hsio: Add i.MX8QM HSIO PHY driver support")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202406170340.7mk3WU3Q-lkp@intel.com/
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240620-phy-fsl-imx8qm-hsio-add-bitfield-include-v1-1-5c7c09ed87e6@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add i.MX8QM HSIO PHY driver support.
i.MX8QM HSIO has three lane PHY instances, and can be bound to the
following controllers in the different use cases listed in below table.
- two lanes capable PCIEA controller.
- one lane PCIEB controller.
- AHCI SATA controller.
i.MX8QM HSIO PHYs support the following use cases.
+----------------------------------------------------+
| | Lane0| Lane1| Lane2|
|-------------------------------|------|------|------|
| use case 1: PCIEAX2SATA | PCIEA| PCIEA| SATA |
|-------------------------------|------|------|------|
| use case 2: PCIEAX2PCIEB | PCIEA| PCIEA| PCIEB|
|-------------------------------|------|------|------|
| use case 3: PCIEAPCIEBSATA | PCIEA| PCIEB| SATA |
+----------------------------------------------------+
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/1716962565-2084-3-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add mipi dphy tx support for the StarFive JH7110 SoC.
It is a module which is used to receive data from DSI
driver and transfer data to DSI interface like mipi screen.
Signed-off-by: Shengyang Chen <shengyang.chen@starfivetech.com>
Reviewed-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Link: https://lore.kernel.org/r/20240418035020.47876-3-shengyang.chen@starfivetech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Existing device trees specify only a single clock-output-name for the
PCIe PHYs. The function phy_aux_clk_register() expects a second entry in
that property. When it doesn't find it, it returns an error, thus
failing the probe of the PHY and thus breaking support for the
corresponding PCIe host.
Follow the approach of the combo USB+DT PHY and generate the name for
the AUX clocks instead of requiring it in DT.
Fixes: 583ca9ccfa ("phy: qcom: qmp-pcie: register second optional PHY AUX clock")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240614-fix-pcie-phy-compat-v3-1-730d1811acf4@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/phy/broadcom/phy-bcm-ns-usb2.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/phy/broadcom/phy-bcm-ns-usb3.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240608-md-drivers-phy-broadcom-v1-1-f070f84cc3f0@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While commit 255ec3879d ("phy: exynos5-usbdrd: Add 26MHz ref clk
support") correctly states that CLKRSTCTRL[7:5] doesn't need to be set
on modern Exynos platforms, SSPPLLCTL[2:0] should be programmed with
the frequency of the reference clock for the USB2.0 phy instead.
I stumbled across this while adding support for the Google Tensor
gs101, but this should apply to E850 just the same.
Do so.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-5-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using 0x82 seems odd, where everything else is just a sequence.
On E850, this macro isn't used (as a register value), only to assign
its value to the 'extrefclk' variable, which is otherwise unused on
that platform. Older platforms don't appear to support 26MHz in the
first place (since this macro was added for E850).
Furthermore, the downstream driver uses 0x82 to denote
USBPHY_REFCLK_DIFF_26MHZ (whatever that means exactly), but for all the
other values we match downstream's non-DIFF macros.
Update to avoid confusion. No functional change intended.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-4-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
on / not on is just a boolean flag and is a bit misleading as currently
on==1 means to turn off the power, and on==0 to turn power on.
Rename the flag and make it a bool to avoid confusion of future readers
of this code. No functional change.
While at it, fix a whitespace issue in nearby comment.
No functional change.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-3-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The timers-howto recommends using usleep_range() and friends anytime
waiting for >= ~10us is required. Doing so can help the timer subsystem
a lot to coalesce wakeups.
Additionally, fsleep() exists as a convenient wrapper so we do not have
to think about which exact sleeping function is required in which case.
Convert all udelay() calls in this driver to use fsleep() to follow the
recommendataion.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-2-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Most of the macros are ordered high -> low, but there are some
outliers.
Order them all uniformly from high to low. This will allow adding
additional register (field) definitions in a consistent way.
While at it, also remove some extra empty lines to group register bit
field definitions together with the relevant register. This makes the
registers easier to distinguish visually.
No functional change.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-1-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Runtime PM is not supported while USB PHY can be turned off from
register accesses.
Add runtime PM for the USB2.0 PHY. The PHY is entirely shut down to save
as much power as possible. This means that gadgets will not be discovered
once suspend state is entered, and suspend state can not be left without
an explicit user intervention (through sysfs). That's why runtime PM is
disabled by default.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Link: https://lore.kernel.org/r/20240528102026.40136-2-bastien.curutchet@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for a single-lane and two-lane PCIe PHYs
found on Qualcomm IPQ9574 platform.
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Link: https://lore.kernel.org/r/20240516032436.2681828-5-quic_devipriy@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently, none of the X1E80100 supported boards upstream have enabled
DP. As for USB, the reason it is not broken when it's obvious that the
offsets are wrong is because the only difference with respect to USB is
the difference in register name. The V6 uses QPHY_V6_PCS_CDR_RESET_TIME
while V6 N4 uses QPHY_V6_N4_PCS_RX_CONFIG. Now, in order for the DP to
work, the DP serdes tables need to be added as they have different
values for V6 N4 when compared to V6 ones, even though they use the same
V6 offsets. While at it, switch swing and pre-emphasis tables to V6 as
well.
Fixes: d7b3579f84 ("phy: qcom-qmp-combo: Add x1e80100 USB/DP combo phys")
Co-developed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240527-x1e80100-phy-qualcomm-combo-fix-dp-v1-3-be8a0b882117@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The new X1E80100 SoC bumps up the HW version of QMP phy to v6 N4 for
combo USB and DP PHY. Currently, the X1E80100 uses the pure V6 PCS
register offsets, which are different. Add the offsets so the
mentioned platform can be fixed later on. Add the new PCS offsets
in a dedicated header file.
Fixes: d7b3579f84 ("phy: qcom-qmp-combo: Add x1e80100 USB/DP combo phys")
Co-developed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240527-x1e80100-phy-qualcomm-combo-fix-dp-v1-2-be8a0b882117@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently, the x1e80100 uses pure V6 register offsets for DP part of the
combo PHY. This hasn't been an issue because external DP is not yet
enabled on any of the boards yet. But in order to enabled it, all these
new V6 N4 register offsets are needed. So add them.
Fixes: 762c3565f3 ("phy: qcom-qmp: qserdes-txrx: Add V6 N4 register offsets")
Co-developed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240527-x1e80100-phy-qualcomm-combo-fix-dp-v1-1-be8a0b882117@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'miphy_initval' is unused since the original
commit 2c14e9be0c ("phy: miphy28lp: Provide support for the MiPHY28lp
Generic PHY").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20240527205844.165279-1-linux@treblig.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'regval' is unused since the original
commit f8aa660841 ("phy: starfive: Add mipi dphy rx support").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Link: https://lore.kernel.org/r/20240527205937.165325-1-linux@treblig.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SC8180X platform has two UNIPHY blocks, add support for these in the
QMP driver.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240525-sc8180x-usb-mp-v1-2-60a904392438@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add suspend and resume support.
The already_configured flag is cleared during the suspend stage to force
the PHY initialization during the resume stage.
Co-developed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240412-j7200-phy-s2r-v1-8-f15815833974@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Even if a PHY is already configured, the PHY operations are needed during
resume stage, as the PHY is in reset state.
The noop_ops PHY operations is removed to always have PHY operations.
The already_configured flag is checked at the begening of init, configure
and poweron operations to keep the already_configured behaviour.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240412-j7200-phy-s2r-v1-7-f15815833974@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Resets are needed during suspend and resume stages.
So they shall be registered during the probe even the phy is already
initialized.
The function cdns_torrent_reset is renamed cdns_torrent_of_get_reset() to
make it clear.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240412-j7200-phy-s2r-v1-5-f15815833974@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Extract calls to clk_get from cdns_torrent_clk into a separate function.
It needs to call cdns_torrent_clk at resume without looking up the clock.
Co-developed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240412-j7200-phy-s2r-v1-4-f15815833974@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add resume support.
It has been tested on J7200 SR1.0 and SR2.0.
Co-developed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240412-j7200-phy-s2r-v1-3-f15815833974@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The wiz_clock_init() function mixes probe and hardware configuration.
Rename the wiz_clock_init() to wiz_clock_probe() and move the hardware
configuration part in a new function named wiz_clock_init().
This hardware configuration sequence must be called during the resume
stage of the driver.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240412-j7200-phy-s2r-v1-2-f15815833974@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- New Support
- Support for Embedded DisplayPort and DisplayPort submodes and driver
support on Qualcomm X1E80100 edp driver
- Qualcomm QMP UFS PHY for SM8475, QMP USB phy for QDU1000/QRU1000 and
eusb2-repeater for SMB2360
- Samsung HDMI PHY for i.MX8MP, gs101 UFS phy
- Mediatek XFI T-PHY support for mt7988
- Rockchip usbdp combo phy driver
- Updates
- Qualcomm x4 lane EP support for sa8775p, v4 ad v6 support for X1E80100,
SM8650 tables for UFS Gear 4 & 5 and correct voltage swing tables
- Freescale imx8m-pci pcie link-up updates
- Rockchip rx-common-refclk-mode support
- More platform remove callback returning void conversions
-----BEGIN PGP SIGNATURE-----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=og1j
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull generic phy updates from Vinod Koul:
"New HW Support:
- Support for Embedded DisplayPort and DisplayPort submodes and
driver support on Qualcomm X1E80100 edp driver
- Qualcomm QMP UFS PHY for SM8475, QMP USB phy for QDU1000/QRU1000
and eusb2-repeater for SMB2360
- Samsung HDMI PHY for i.MX8MP, gs101 UFS phy
- Mediatek XFI T-PHY support for mt7988
- Rockchip usbdp combo phy driver
Updates:
- Qualcomm x4 lane EP support for sa8775p, v4 ad v6 support for
X1E80100, SM8650 tables for UFS Gear 4 & 5 and correct voltage
swing tables
- Freescale imx8m-pci pcie link-up updates
- Rockchip rx-common-refclk-mode support
- More platform remove callback returning void conversions"
* tag 'phy-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (43 commits)
dt-bindings: phy: qcom,usb-snps-femto-v2: use correct fallback for sc8180x
dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: fix msm899[68] power-domains
dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: fix x1e80100-gen3x2 schema
phy: qcpm-qmp-usb: Add support for QDU1000/QRU1000
dt-bindings: phy: qcom,qmp-usb: Add QDU1000 USB3 PHY
dt-bindings: phy: qcom,usb-snps-femto-v2: Add bindings for QDU1000
phy: qcom-qmp-pcie: add x4 lane EP support for sa8775p
phy: samsung-ufs: ufs: exit on first reported error
phy: samsung-ufs: ufs: remove superfluous mfd/syscon.h header
phy: rockchip: fix CONFIG_TYPEC dependency
phy: rockchip: usbdp: fix uninitialized variable
phy: rockchip-snps-pcie3: add support for rockchip,rx-common-refclk-mode
dt-bindings: phy: rockchip,pcie3-phy: add rockchip,rx-common-refclk-mode
phy: rockchip: add usbdp combo phy driver
dt-bindings: phy: add rockchip usbdp combo phy document
phy: add driver for MediaTek XFI T-PHY
dt-bindings: phy: mediatek,mt7988-xfi-tphy: add new bindings
phy: freescale: fsl-samsung-hdmi: Convert to platform remove callback returning void
phy: qcom: qmp-ufs: update SM8650 tables for Gear 4 & 5
MAINTAINERS: Add phy-gs101-ufs file to Tensor GS101.
...
Updates for v6.10
Core:
- Switched to generating register header files during build process
instead of shipping pre-generated headers
- Merged DPU and MDP4 format databases.
DP:
- Stop using compat string to distinguish DP and eDP cases
- Added support for X Elite platform (X1E80100)
- Reworked DP aux/audio support
- Added SM6350 DP to the bindings (no driver changes, using SM8350
as a fallback compat)
GPU:
- a7xx perfcntr reg fixes
- MAINTAINERS updates
- a750 devcoredump support
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtpw6dNR9JBikFTQ=TCpt-9FeFW+SGjXWv+Jv3emm0Pbg@mail.gmail.com
Add support for x4 lane end point mode PHY found on sa8755p platform.
Reusing existing serdes and pcs_misc table for EP and moved
BIAS_EN_CLKBUFLR_EN register from RC serdes table to common serdes
table as this register is part of both RC and EP.
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/1714494089-7917-2-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To preserve the err value, exit the loop immediately if an error
is returned.
Fixes: f2c6d0fa19 ("phy: samsung-ufs: use exynos_get_pmu_regmap_by_phandle() to obtain PMU regmap")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240426104129.2211949-3-peter.griffin@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
mfd/syscon.h header is no longer required since the update to
exynos_get_pmu_regmap_by_phandle() api.
Fixes: f2c6d0fa19 ("phy: samsung-ufs: use exynos_get_pmu_regmap_by_phandle() to obtain PMU regmap")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240426104129.2211949-2-peter.griffin@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The newly added driver causes a warning about missing dependencies
by selecting CONFIG_TYPEC unconditionally:
WARNING: unmet direct dependencies detected for TYPEC
Depends on [n]: USB_SUPPORT [=n]
Selected by [y]:
- PHY_ROCKCHIP_USBDP [=y] && ARCH_ROCKCHIP [=y] && OF [=y]
WARNING: unmet direct dependencies detected for USB_COMMON
Depends on [n]: USB_SUPPORT [=n]
Selected by [y]:
- EXTCON_RTK_TYPE_C [=y] && EXTCON [=y] && (ARCH_REALTEK [=y] || COMPILE_TEST [=y]) && TYPEC [=y]
Since that is a user-visible option, it should not really be selected
in the first place. Replace the 'select' with a 'depends on' as
we have for similar drivers.
Fixes: 2f70bbddeb ("phy: rockchip: add usbdp combo phy driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240415174241.77982-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The ret variable may not be initialized in rk_udphy_usb3_phy_init(), if
the PHY is not using USB3 mode.
Since the DisplayPort part is handled separately and the PHY does not
support USB2 (which is routed to another PHY on Rockchip RK3588), the
right exit code for this case is 0. Thus let's initialize the variable
accordingly.
Fixes: 2f70bbddeb ("phy: rockchip: add usbdp combo phy driver")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404141048.qFAYDctQ-lkp@intel.com/
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/20240416145233.94687-1-sebastian.reichel@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
>From the RK3588 Technical Reference Manual, Part1,
section 6.19 PCIe3PHY_GRF Register Description:
"rxX_cmn_refclk_mode"
RX common reference clock mode for lane X. This mode should be enabled
only when the far-end and near-end devices are running with a common
reference clock.
The hardware reset value for this field is 0x1 (enabled).
Note that this register field is only available on RK3588, not on RK3568.
The link training either fails or is highly unstable (link state will jump
continuously between L0 and recovery) when this mode is enabled while
using an endpoint running in Separate Reference Clock with No SSC (SRNS)
mode or Separate Reference Clock with SSC (SRIS) mode.
(Which is usually the case when using a real SoC as endpoint, e.g. the
RK3588 PCIe controller can run in both Root Complex and Endpoint mode.)
Add support for the device tree property rockchip,rx-common-refclk-mode,
such that the PCIe PHY can be used in configurations where the Root
Complex and Endpoint are not using a common reference clock.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20240412125818.17052-3-cassel@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This adds a new USBDP combo PHY with Samsung IP block driver.
The driver get lane mux and mapping info in 2 ways, supporting
DisplayPort alternate mode or parsing from DT. When parsing from DT,
the property "rockchip,dp-lane-mux" provide the DP mux and mapping
info. This is needed when the PHY is not used with TypeC Alt-Mode.
For example if the USB3 interface of the PHY is connected to a USB
Type A connector and the DP interface is connected to a DisplayPort
connector.
When do DP link training, need to set lane number, link rate, swing,
and pre-emphasis via PHY configure interface.
Co-developed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Co-developed-by: Zhang Yubing <yubing.zhang@rock-chips.com>
Signed-off-by: Zhang Yubing <yubing.zhang@rock-chips.com>
Co-developed-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240408225109.128953-3-sebastian.reichel@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The power_supply frame-work is not really designed for there to be
long living in kernel references to power_supply devices.
Specifically unregistering a power_supply while some other code has
a reference to it triggers a WARN in power_supply_unregister():
WARN_ON(atomic_dec_return(&psy->use_cnt));
Folllowed by the power_supply still getting removed and the
backing data freed anyway, leaving the tusb1210 charger-detect code
with a dangling reference, resulting in a crash the next time
tusb1210_get_online() is called.
Fix this by only holding the reference in tusb1210_get_online()
freeing it at the end of the function. Note this still leaves
a theoretical race window, but it avoids the issue when manually
rmmod-ing the charger chip driver during development.
Fixes: 48969a5623 ("phy: ti: tusb1210: Add charger detection")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240406140821.18624-1-hdegoede@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 5abed58a8b ("phy: qcom: qmp-combo: Fix VCO div offset on v3")
fixed a regression introduced in 6.5 by making sure that the correct
offset is used for the DP_PHY_VCO_DIV register on v3 hardware.
Unfortunately, that fix instead broke DisplayPort on v5_5nm and v6
hardware as it failed to add the corresponding offsets also to those
register tables.
Fixes: 815891eee6 ("phy: qcom-qmp-combo: Introduce orientation variable")
Fixes: 5abed58a8b ("phy: qcom: qmp-combo: Fix VCO div offset on v3")
Cc: stable@vger.kernel.org # 6.5: 5abed58a8b
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20240408093023.506-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add driver for MediaTek's XFI T-PHY which can be found in the MT7988
SoC. The XFI T-PHY is a 10 Gigabit/s Ethernet SerDes PHY with muxes on
the internal side to be used with either USXGMII PCS or LynxI PCS,
depending on the selected PHY interface mode.
The PHY can operates only in PHY_MODE_ETHERNET, the submode is one of
PHY_INTERFACE_MODE_* corresponding to the supported modes:
* USXGMII \
* 10GBase-R }- USXGMII PCS - XGDM \
* 5GBase-R / \
}- Ethernet MAC
* 2500Base-X \ /
* 1000Base-X }- LynxI PCS - GDM /
* Cisco SGMII (MAC side) /
I chose the name XFI T-PHY because names of functions dealing with the
phy in the vendor driver are prefixed "xfi_pextp_".
The register space used by the phy is called "pextp" in the vendor
sources, which could be read as "_P_CI _ex_press _T_-_P_hy", and that
is quite misleading as this phy isn't used for anything related to
PCIe, so I wanted to find a better name.
XFI is still somehow related (as in: you would find the relevant
places using grep in the vendor driver when looking for that) and the
term seemed to at least somehow be aligned with the function of that
phy: Dealing with (up to) 10 Gbit/s Ethernet serialized differential
signals.
In order to work-around a performance issue present on the first of
two XFI T-PHYs found in MT7988, special tuning is applied which can
be selected by adding the 'mediatek,usxgmii-performance-errata'
property to the device tree node, similar to how the vendor driver is
doing that too.
There is no documentation for most registers used for the
analog/tuning part, however, most of the registers have been partially
reverse-engineered from MediaTek's SDK implementation (see links, an
opaque sequence of 32-bit register writes) and descriptions for all
relevant digital registers and bits such as resets and muxes have been
supplied by MediaTek.
Link: b72d6cba92/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_sgmii.c
Link: dec96a1d9b/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_eth_soc.c
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/8719c82634df7e8e984f1a608be3ba2f2d494fb4.1712625857.git.daniel@makrotopia.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240409161505.66619-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update the SM8650 UFS PHY init tables to support Gear 4 and Gear 5
using the overlays setup (only supported Gear 5 before), and sync
back with the latest Qualcomm recommended values.
The new recommended values allow a solid 50% bump in sequential
read/write benchmarks on the SM8650 QRD & HDK reference boards.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240410-topic-sm8650-upstream-ufs-g5-v1-1-5527c44b37e6@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Ensure CONFIG_RATIONAL is selected in order to fix the following link
error with some kernel configurations:
drivers/phy/rockchip/phy-rockchip-samsung-hdptx.o: in function `rk_hdptx_ropll_tmds_cmn_config':
phy-rockchip-samsung-hdptx.c:(.text+0x950): undefined reference to `rational_best_approximation'
Fixes: 553be2830c ("phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404090540.2l1TEkDF-lkp@intel.com/
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240408222926.32708-1-cristian.ciocaltea@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to the 'qcom,ipq5332-usb-hsphy.yaml' schema, the 5V
supply regulator must be defined via the 'vdd-supply' property.
The driver however requests for the 'vdda-phy' regulator which
results in the following message when the driver is probed on
a IPQ5018 based board with a device tree matching to the schema:
qcom-m31usb-phy 5b000.phy: supply vdda-phy not found, using dummy regulator
qcom-m31usb-phy 5b000.phy: Registered M31 USB phy
This means that the regulator specified in the device tree never
gets enabled.
Change the driver to use the 'vdd' name for the regulator as per
defined in the schema in order to ensure that the corresponding
regulator gets enabled.
Fixes: 08e49af507 ("phy: qcom: Introduce M31 USB PHY driver")
Reviewed-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240406-phy-qcom-m31-regulator-fix-v2-1-c8e9795bc071@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The register base that was used to write to the QSERDES_DP_PHY_MODE
register was 'dp_dp_phy' before commit 815891eee6 ("phy:
qcom-qmp-combo: Introduce orientation variable"). There isn't any
explanation in the commit why this is changed, so I suspect it was an
oversight or happened while being extracted from some other series.
Oddly the value being 0x4c or 0x5c doesn't seem to matter for me, so I
suspect this is dead code, but that can be fixed in another patch. It's
not good to write to the wrong register space, and maybe some other
version of this phy relies on this.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Abel Vesa <abel.vesa@linaro.org>
Cc: Steev Klimaszewski <steev@kali.org>
Cc: Johan Hovold <johan+linaro@kernel.org>
Cc: Bjorn Andersson <quic_bjorande@quicinc.com>
Cc: stable@vger.kernel.org # 6.5
Fixes: 815891eee6 ("phy: qcom-qmp-combo: Introduce orientation variable")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240405000111.1450598-1-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit ec17373aeb ("phy: qcom: qmp-combo: extract common function to
setup clocks") changed the offset that is used to write to
DP_PHY_VCO_DIV from QSERDES_V3_DP_PHY_VCO_DIV to
QSERDES_V4_DP_PHY_VCO_DIV. Unfortunately, this offset is different
between v3 and v4 phys:
#define QSERDES_V3_DP_PHY_VCO_DIV 0x064
#define QSERDES_V4_DP_PHY_VCO_DIV 0x070
meaning that we write the wrong register on v3 phys now. Add another
generic register to 'regs' and use it here instead of a version specific
define to fix this.
This was discovered after Abhinav looked over register dumps with me
from sc7180 Trogdor devices that started failing to light up the
external display with v6.6 based kernels. It turns out that some
monitors are very specific about their link clk frequency and if the
default power on reset value is still there the monitor will show a
blank screen or a garbled display. Other monitors are perfectly happy to
get a bad clock signal.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: ec17373aeb ("phy: qcom: qmp-combo: extract common function to setup clocks")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240404234345.1446300-1-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The pcie1l0_sel and pcie1l1_sel bits in PCIESEL_CON configure the
mux for PCIe1L0 and PCIe1L1 to either the PIPE Combo PHYs or the
PCIe3 PHY. Thus this configuration interfers with the data-lanes
configuration done by the PCIe3 PHY.
RK3588 has three Combo PHYs. The first one has a dedicated PCIe
controller and is not affected by this. For the other two Combo
PHYs, there is one mux for each of them.
pcie1l0_sel selects if PCIe 1L0 is muxed to Combo PHY 1 when
bit is set to 0 or to the PCIe3 PHY when bit is set to 1.
pcie1l1_sel selects if PCIe 1L1 is muxed to Combo PHY 2 when
bit is set to 0 or to the PCIe3 PHY when bit is set to 1.
Currently the code always muxes 1L0 and 1L1 to the Combi PHYs
once one of them is being used in PCIe mode. This is obviously
wrong when at least one of the ports should be muxed to the
PCIe3 PHY.
Fix this by introducing Combo PHY identification and then only
setting up the required bit.
Fixes: a03c442772 ("phy: rockchip: Add naneng combo phy support for RK3588")
Reported-by: Michal Tomek <mtdev79b@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240404-rk3588-pcie-bifurcation-fixes-v1-3-9907136eeafd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently the PCIe v3 PHY driver only sets the pcie1ln_sel bits, but
does not clear them because of an incorrect write mask. This fixes up
the issue by using a newly introduced constant for the write mask.
While at it also introduces a proper GENMASK based constant for the
PCIE30_PHY_MODE.
Fixes: 2e9bffc4f7 ("phy: rockchip: Support PCIe v3")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240404-rk3588-pcie-bifurcation-fixes-v1-2-9907136eeafd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
So far all RK3588 boards use fully aggregated PCIe. CM3588 is one
of the few boards using this feature and apparently it is broken.
The PHY offers the following mapping options:
port 0 lane 0 - always mapped to controller 0 (4L)
port 0 lane 1 - to controller 0 or 2 (1L0)
port 1 lane 0 - to controller 0 or 1 (2L)
port 1 lane 1 - to controller 0, 1 or 3 (1L1)
The data-lanes DT property maps these as follows:
0 = no controller (unsupported by the HW)
1 = 4L
2 = 2L
3 = 1L0
4 = 1L1
That allows the following configurations with first column being the
mainline data-lane mapping, second column being the downstream name,
third column being PCIE3PHY_GRF_CMN_CON0 and PHP_GRF_PCIESEL register
values and final column being the user visible lane setup:
<1 1 1 1> = AGGREG = [4 0] = x4 (aggregation)
<1 1 2 2> = NANBNB = [0 0] = x2 x2 (no bif.)
<1 3 2 2> = NANBBI = [1 1] = x2 x1x1 (bif. of port 0)
<1 1 2 4> = NABINB = [2 2] = x1x1 x2 (bif. of port 1)
<1 3 2 4> = NABIBI = [3 3] = x1x1 x1x1 (bif. of both ports)
The driver currently does not program PHP_GRF_PCIESEL correctly, which
is fixed by this patch. As a side-effect the new logic is much simpler
than the old logic.
Fixes: 2e9bffc4f7 ("phy: rockchip: Support PCIe v3")
Signed-off-by: Michal Tomek <mtdev79b@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240404-rk3588-pcie-bifurcation-fixes-v1-1-9907136eeafd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the m-phy tuning values for gs101 UFS phy and SoC callbacks
gs101_phy_wait_for_calibration() and gs101_phy_wait_for_cdr_lock().
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240404122559.898930-12-peter.griffin@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some SoCs like gs101 don't fit in well with the existing pll lock and
clock data recovery (CDR) callback used by existing exynos platforms.
Allow SoCs to specifify and implement their own calibration and CDR
functions that can be called by the generic samsung phy code.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240404122559.898930-11-peter.griffin@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This allows us to obtain a PMU regmap that is created by the exynos-pmu
driver. Platforms such as gs101 require exynos-pmu created regmap to
issue SMC calls for PMU register accesses. Existing platforms still get
a MMIO regmap as before.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20240404122559.898930-10-peter.griffin@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Leaving AUX_PLL_REFCLK_SEL at its reset default of AUX_IN (PLL clock)
proves to be more stable on the i.MX 8M Mini.
Fixes: 1aa97b0022 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Link: https://lore.kernel.org/r/20240322130646.1016630-2-marcel@ziswiler.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since commit 43a7206b09 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the phy_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: "Ricardo B. Marliere" <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240305-class_cleanup-phy-v1-1-106013a644dc@marliere.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe Gen4x2 PHY found in the SM8[456]50 SoCs have a second clock,
enable this second clock by setting the proper 20MHz hardware rate in
the Gen4x2 SM8[456]50 aux_clock_rate config fields.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-4-3ec0a966d52f@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe Gen4x2 PHY found in the SM8[456]50 SoCs have a second clock,
add the code to register it for PHYs configs that sets a aux_clock_rate.
In order to get the right clock, add qmp_pcie_clk_hw_get() which uses
the newly introduced QMP_PCIE_PIPE_CLK & QMP_PCIE_PHY_AUX_CLK clock
IDs and also supports the legacy bindings by returning the PIPE clock
when #clock-cells=0.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-3-3ec0a966d52f@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe Gen4x2 PHY found in the SM8[456]50 SoCs have a second clock,
in order to expose it, split the current clock registering in two parts:
- CCF clock registering
- DT clock registering
Keep the of_clk_add_hw_provider/devm_add_action_or_reset to keep
compatibility with the legacy subnode bindings.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-2-3ec0a966d52f@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is an out of bounds read access of 'gbe_phy_init_fix[fix_idx].addr'
every iteration after 'fix_idx' reaches 'ARRAY_SIZE(gbe_phy_init_fix)'.
Make sure 'gbe_phy_init[addr]' is used when all elements of
'gbe_phy_init_fix' array are handled.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 934337080c ("phy: marvell: phy-mvebu-a3700-comphy: Add native kernel implementation")
Signed-off-by: Mikhail Kobuk <m.kobuk@ispras.ru>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20240321164734.49273-1-m.kobuk@ispras.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/57a3338a1cec683ac84d48e00dbf197e15ee5481.1709886922.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Several functions had "rochchip" instead of "rockchip" in their name.
Replace "rochchip" by "rockchip".
Signed-off-By: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240307095318.3651498-1-rick.wertenbroek@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The QMP USB3/DP PHY found in the SM8650 SoC requires a slightly
different Voltage Swing table for HBR/RBR link speeds.
Add a new hbr/rbr voltage switch table named "v6" used in a new
sm8650 qmp_phy_cfg struct replacing the sm8550 fallback used for
the sm8650 compatible.
Fixes: 80c1afe8c5 ("phy: qcom: qmp-combo: add QMP USB3/DP PHY tables for SM8650")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240226-topic-sm8650-upstream-combo-phy-swing-update-v1-1-08707ebca92a@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add v6 HW support by implementing the version ops. Add the X1E80100
compatible and match config as it is v6.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240221-phy-qualcomm-edp-x1e80100-v4-3-4e5018877bee@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Future platforms should not use different compatibles to differentiate
between eDP and DP mode. Instead, they should use a single compatible as
the IP block is the same. It will be the job of the controller to set the
submode of the PHY accordingly.
The existing platforms will remain with separate compatibles for each
mode.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240324-x1e80100-phy-edp-compatible-refactor-v5-2-a0db5f3150bc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This adds the driver for the Samsung HDMI PHY found on the
i.MX8MP SoC. Based on downstream implementation from
Sandor Yu <Sandor.yu@nxp.com>. According to the TRM, the PHY
receives parallel data from the link and serializes it. It
also sets the PLL clock needed for the TX serializer.
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Co-developed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> # Kontron BL
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Link: https://lore.kernel.org/r/20240227220444.77566-3-aford173@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the big set of USB and Thunderbolt changes for 6.9-rc1. Lots of
tiny changes and forward progress to support new hardware and better
support for existing devices. Included in here are:
- Thunderbolt (i.e. USB4) updates for newer hardware and uses as more
people start to use the hardware
- default USB authentication mode Kconfig and documentation update to
make it more obvious what is going on
- USB typec updates and enhancements
- usual dwc3 driver updates
- usual xhci driver updates
- function USB (i.e. gadget) driver updates and additions
- new device ids for lots of drivers
- loads of other small updates, full details in the shortlog
All of these, including a "last minute regression fix" have been in
linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZfwpzA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymS9QCdEuF6KJFLOrDrGS4NbZNSUPIVF6oAn350r4NX
CMZah37Dfr1VDCOOV4gQ
=HACL
-----END PGP SIGNATURE-----
Merge tag 'usb-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.9-rc1. Lots
of tiny changes and forward progress to support new hardware and
better support for existing devices. Included in here are:
- Thunderbolt (i.e. USB4) updates for newer hardware and uses as more
people start to use the hardware
- default USB authentication mode Kconfig and documentation update to
make it more obvious what is going on
- USB typec updates and enhancements
- usual dwc3 driver updates
- usual xhci driver updates
- function USB (i.e. gadget) driver updates and additions
- new device ids for lots of drivers
- loads of other small updates, full details in the shortlog
All of these, including a "last minute regression fix" have been in
linux-next with no reported issues"
* tag 'usb-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (185 commits)
usb: usb-acpi: Fix oops due to freeing uninitialized pld pointer
usb: gadget: net2272: Use irqflags in the call to net2272_probe_fin
usb: gadget: tegra-xudc: Fix USB3 PHY retrieval logic
phy: tegra: xusb: Add API to retrieve the port number of phy
USB: gadget: pxa27x_udc: Remove unused of_gpio.h
usb: gadget/snps_udc_plat: Remove unused of_gpio.h
usb: ohci-pxa27x: Remove unused of_gpio.h
usb: sl811-hcd: only defined function checkdone if QUIRK2 is defined
usb: Clarify expected behavior of dev_bin_attrs_are_visible()
xhci: Allow RPM on the USB controller (1022:43f7) by default
usb: isp1760: remove SLAB_MEM_SPREAD flag usage
usb: misc: onboard_hub: use pointer consistently in the probe function
usb: gadget: fsl: Increase size of name buffer for endpoints
usb: gadget: fsl: Add of device table to enable module autoloading
usb: typec: tcpm: add support to set tcpc connector orientatition
usb: typec: tcpci: add generic tcpci fallback compatible
dt-bindings: usb: typec-tcpci: add tcpci fallback binding
usb: gadget: fsl-udc: Replace custom log wrappers by dev_{err,warn,dbg,vdbg}
usb: core: Set connect_type of ports based on DT node
dt-bindings: usb: Add downstream facing ports to realtek binding
...
This patch introduces a new API, tegra_xusb_padctl_get_port_number,
to the Tegra XUSB Pad Controller driver. This API is used to identify
the USB port that is associated with a given PHY.
The function takes a PHY pointer for either a USB2 PHY or USB3 PHY as input
and returns the corresponding port number. If the PHY pointer is invalid,
it returns -ENODEV.
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20240307030328.1487748-2-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to a long-standing issue in driver core, drivers may not probe defer
after having registered child devices to avoid triggering a probe
deferral loop (see fbc35b45f9 ("Add documentation on meaning of
-EPROBE_DEFER")).
Move registration of the typec switch to after looking up clocks and
other resources.
Note that PHY creation can in theory also trigger a probe deferral when
a 'phy' supply is used. This does not seem to affect the QMP PHY driver
but the PHY subsystem should be reworked to address this (i.e. by
separating initialisation and registration of the PHY).
Fixes: 2851117f8f ("phy: qcom-qmp-combo: Introduce orientation switching")
Cc: stable@vger.kernel.org # 6.5
Cc: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240217150228.5788-7-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Due to a long-standing issue in driver core, drivers may not probe defer
after having registered child devices to avoid triggering a probe
deferral loop (see fbc35b45f9 ("Add documentation on meaning of
-EPROBE_DEFER")).
This could potentially also trigger a bug in the DRM bridge
implementation which does not expect bridges to go away even if device
links may avoid triggering this (when enabled).
Move registration of the DRM aux bridge to after looking up clocks and
other resources.
Note that PHY creation can in theory also trigger a probe deferral when
a 'phy' supply is used. This does not seem to affect the QMP PHY driver
but the PHY subsystem should be reworked to address this (i.e. by
separating initialisation and registration of the PHY).
Fixes: 35921910bb ("phy: qcom: qmp-combo: switch to DRM_AUX_BRIDGE")
Fixes: 1904c3f578 ("phy: qcom-qmp-combo: Introduce drm_bridge")
Cc: stable@vger.kernel.org # 6.5
Cc: Bjorn Andersson <quic_bjorande@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240217150228.5788-6-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The xlate callbacks are supposed to translate of_phandle_args to proper
provider without modifying the of_phandle_args. Make the argument
pointer to const for code safety and readability.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Link: https://lore.kernel.org/r/20240217093937.58234-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The MSM8996 platform has registers setup different to the rest of QMP v3
USB platforms. It has PCS region at 0x600 and no PCS_MISC region, while
other platforms have PCS region at 0x800 and PCS_MISC at 0x600. This
results in the malfunctioning USB host on some of the platforms. The
commit f74c35b630 ("phy: qcom-qmp-usb: fix register offsets for
ipq8074/ipq6018") fixed the issue for IPQ platforms, but missed the
SDM845 which has the same register layout.
To simplify future platform addition and to make the driver more future
proof, rename qmp_usb_offsets_v3 to qmp_usb_offsets_v3_msm8996 (to mark
its peculiarity), rename qmp_usb_offsets_ipq8074 to qmp_usb_offsets_v3
and use it for SDM845 platform.
Fixes: 2be22aae6b ("phy: qcom-qmp-usb: populate offsets configuration")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240213133824.2218916-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add driver for the HDMI/eDP TX Combo PHY found on Rockchip RK3588 SoC.
The PHY is based on a Samsung IP block and supports HDMI 2.1 TMDS, FRL
and eDP links. The maximum data rate is 12Gbps (FRL), while the minimum
is 250Mbps (TMDS).
Only the TMDS link is currently supported.
Co-developed-by: Algea Cao <algea.cao@rock-chips.com>
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240214-phy-hdptx-v4-2-e7974f46c1a7@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The resume callback restores the submode of each PHY.
It uses the submode stored in struct phy_gmii_sel_phy_priv (variable
phy_if_mode). The submode was saved by the set_mode PHY operation.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240125171754.773909-1-thomas.richard@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is a new driver that supports the MIPI CSI CD-PHY version 0.5
The number of PHYs depend on the SoC.
Each PHY can support D-PHY only or CD-PHY configuration.
The driver supports only D-PHY mode, so CD-PHY
compatible PHY are configured in D-PHY mode.
[Julien Stephan: simplify driver model: one instance per phy vs
one instance for all phys]
Signed-off-by: Louis Kuo <louis.kuo@mediatek.com>
Signed-off-by: Phi-bang Nguyen <pnguyen@baylibre.com>
[Julien Stephan: refactor code]
Co-developed-by: Julien Stephan <jstephan@baylibre.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240111101738.468916-1-jstephan@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a separate compatible and registers map table for TI J7200.
TI J7200 uses Torrent SD0805 version which is a special version
derived from Torrent SD0801 with some differences in register
configurations.
Add register sequences for USXGMII(156.25MHz) + SGMII/QSGMII(100MHz)
multilink config for TI J7200. USXGMII uses PLL0 and SGMII/QSGMII
uses PLL1.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-6-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Torrent PHY can have separate input reference clocks for PLL0 and PLL1.
Add support for dual reference clock multilink configurations.
Add register sequences for PCIe(100MHz) + USXGMII(156.25MHz) multilink
configuration. PCIe uses PLL0 and USXGMII uses PLL1.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-3-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of incrementing the base of the global reg fields, which renders
the second instance of the repeater broken due to wrong offsets, use
regmap with base and offset. As for zeroing out the rest of the tuning
regs, avoid looping though the table and just use the table as is,
as it is already zero initialized.
Fixes: 99a517a582 ("phy: qualcomm: phy-qcom-eusb2-repeater: Zero out untouched tuning regs")
Tested-by: Elliot Berman <quic_eberman@quicinc.com> # sm8650-qrd
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240201-phy-qcom-eusb2-repeater-fixes-v4-1-cf18c8cef6d7@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It should be 'qphy->vreg' passed to PTR_ERR() when devm_regulator_get() fails.
Fixes: 08e49af507 ("phy: qcom: Introduce M31 USB PHY driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/20230824091345.1072650-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Device drivers should just rely on the clocks provided by the devicetree
and enable/disable them based on the requirement. There is no need to
validate the clocks provided by devicetree in the driver. That's the job
of DT schema.
So let's switch to devm_clk_bulk_get_all() API that just gets the clocks
provided by devicetree and remove hardcoded clocks info.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-2-58a49d2f4605@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If the external phy working together with phy-omap-usb2 does not implement
send_srp(), we may still attempt to call it. This can happen on an idle
Ethernet gadget triggering a wakeup for example:
configfs-gadget.g1 gadget.0: ECM Suspend
configfs-gadget.g1 gadget.0: Port suspended. Triggering wakeup
...
Unable to handle kernel NULL pointer dereference at virtual address
00000000 when execute
...
PC is at 0x0
LR is at musb_gadget_wakeup+0x1d4/0x254 [musb_hdrc]
...
musb_gadget_wakeup [musb_hdrc] from usb_gadget_wakeup+0x1c/0x3c [udc_core]
usb_gadget_wakeup [udc_core] from eth_start_xmit+0x3b0/0x3d4 [u_ether]
eth_start_xmit [u_ether] from dev_hard_start_xmit+0x94/0x24c
dev_hard_start_xmit from sch_direct_xmit+0x104/0x2e4
sch_direct_xmit from __dev_queue_xmit+0x334/0xd88
__dev_queue_xmit from arp_solicit+0xf0/0x268
arp_solicit from neigh_probe+0x54/0x7c
neigh_probe from __neigh_event_send+0x22c/0x47c
__neigh_event_send from neigh_resolve_output+0x14c/0x1c0
neigh_resolve_output from ip_finish_output2+0x1c8/0x628
ip_finish_output2 from ip_send_skb+0x40/0xd8
ip_send_skb from udp_send_skb+0x124/0x340
udp_send_skb from udp_sendmsg+0x780/0x984
udp_sendmsg from __sys_sendto+0xd8/0x158
__sys_sendto from ret_fast_syscall+0x0/0x58
Let's fix the issue by checking for send_srp() and set_vbus() before
calling them. For USB peripheral only cases these both could be NULL.
Fixes: 657b306a7b ("usb: phy: add a new driver for omap usb2 phy")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240128120556.8848-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Follow the example of the rest of the QMP PHY drivers and move SGMII PCS
registers to a separate header file.
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-8-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Qualcomm SGMII SerDes PHY is a QMP PHY. As such, it uses standard
registers for QSERDES COM/RX/TX regions. Use register defines from the
existing headers.
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-7-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All PHYs supported by qmp-usb-legacy driver don't have issues with the
PCS region. Replace qmp_usb_legacy_iomap() with devm_of_iomap().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-2-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All PHYs supported by usb-legacy have two lanes. Drop support for
single-lane configuration.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad DYbcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-1-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller. Added the driver to drive the USB 3.0 PHY transceivers.
Note: New driver, remove the port status notification on legacy USB PHY.
Use the generic PHY to notify the usb device connect and disconnect.
To avoid using these PHYs would require describing the very same
PHY using both the generic "phy" property and the deprecated "usb-phy"
property.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20231213031203.4911-3-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller. Added the driver to drive the USB 2.0 PHY transceivers.
Note: New driver,remove the port status notification on legacy USB PHY.
Use the generic PHY to notify the usb device connect and disconnect.
To avoid using these PHYs would require describing the very same
PHY using both the generic "phy" property and the deprecated "usb-phy"
property.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20231213031203.4911-2-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Realtek SoC, the parameter of usb phy is designed to be able to
do dynamic tuning based in the port status. Therefore, add a notify
callback of phy driver when usb connection/disconnection change.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20231213031203.4911-1-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the datasheet(Table 3-2: Port configuration) the serdes 2
(SD2) can be configured to run QSGMII or SGMII mode. Already the QSGMII
mode is supported in the serdes_muxes list but was missing the SGMII mode.
In this mode the serdes is connected to the port 4.
Therefore add this entry in the list.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20240108205140.1701770-1-horatiu.vultur@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Armada 38x supports 3 functions on serdes #0:
- pcie port 0
- sata port 0
- gbe port 0
Add missing entry for gbe port 0 on serdes 0 to the gbe_mux array.
Because this array looks obscure to new readers, also add a comment
explaining the meaning of rows, columns and values.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20240106-fix-a38x-comphy-sd0-gbe0-v1-1-c7fd87272050@solid-run.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Even if device_create_file() returns error code,
rcar_gen3_phy_usb2_probe() will return zero because the "ret" is
variable shadowing.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202312161021.gOLDl48K-lkp@intel.com/
Fixes: 441a681b88 ("phy: rcar-gen3-usb2: fix implementation for runtime PM")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240105093703.3359949-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For consistency, add the QMP v6 registers layout even though
they are the same as v5. Also switch all QMP v6 PHYs to use this
new layout.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20231223-x1e80100-phy-pcie-v2-2-223c0556908a@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 23fd679249 ("phy: qcom-qmp: add USB3 PHY support for IPQ6018")
noted that IPQ6018 init is identical to IPQ8074. Yet downstream uses
separate serdes init sequence for IPQ6018. Since already existing IPQ9574
serdes init sequence is identical, just reuse it and fix failing USB3 mode
in IPQ6018.
Fixes: 23fd679249 ("phy: qcom-qmp: add USB3 PHY support for IPQ6018")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/1706026160-17520-3-git-send-email-mantas@8devices.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 2be22aae6b ("phy: qcom-qmp-usb: populate offsets configuration")
introduced register offsets to the driver but for ipq8074/ipq6018 they do
not match what was in the old style device tree. Example from old
ipq6018.dtsi:
<0x00078200 0x130>, /* Tx */
<0x00078400 0x200>, /* Rx */
<0x00078800 0x1f8>, /* PCS */
<0x00078600 0x044>; /* PCS misc */
which would translate to:
{.., .pcs = 0x800, .pcs_misc = 0x600, .tx = 0x200, .rx = 0x400 }
but was translated to:
{.., .pcs = 0x600, .tx = 0x200, .rx = 0x400 }
So split usb_offsets and fix USB initialization for IPQ8074 and IPQ6018.
Tested only on IPQ6018
Fixes: 2be22aae6b ("phy: qcom-qmp-usb: populate offsets configuration")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/1706026160-17520-2-git-send-email-mantas@8devices.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The QMP USB PHYs on msm8998, qcm2290 and some other platforms don't have
the PCS_MISC_CLAMP_ENABLE register. Instead they need to toggle the
register in the TCSR space. Make the new phy-qcom-qmp-usbc driver
correctly handle the clamp register.
Fixes: a51969fafc ("phy: qcom-qmp: Add QMP V3 USB3 PHY support for msm8998")
Fixes: 8abe5e778b ("phy: qcom-qmp: Add QCM2290 USB3 PHY support")
Cc: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-3-a950c223f10f@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The USB-C PHYs on the msm8998, QCM2290 and SM6115 platforms use special
register to control which lanes of the Type-C port are used for the
SuperSpeed USB connection. Mimic the qmp-combo driver and handle this
register.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-12-182d9aa0a5b3@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now as all dual-lane PHYs have been migrated to a new driver, drop
support for dual lanes configuration. If the PHY uses two lanes for USB,
it is symthom that it should use either a combo USB+DP or a USB-C PHY
driver.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-11-182d9aa0a5b3@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation to adding Type-C handling for MSM8998, QCM2290 and SM6115
platforms, create new QMP USB-C PHY driver by splitting mentioned
platforms to a separate file. In future it will also be extended with
support for the DisplayPort handling. It will also be reused later for
such platforms as SDM660, SM6125, SM6150.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-10-182d9aa0a5b3@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On SM8550, two sets of UFS PHY settings are provided, one set is to support
HS-G5, another set is to support HS-G4 and lower gears. The two sets of PHY
settings are programming different values to different registers, mixing
the two sets and/or overwriting one set with another set is definitely not
blessed by UFS PHY designers.
To add HS-G5 support for SM8550, split the two sets of PHY settings into
their dedicated overlay tables, only the common parts of the two sets of
PHY settings are left in the .tbls.
Consider we are going to add even higher gear support in future, to avoid
adding more tables with different names, rename the .tbls_hs_g4 and make it
an array, a size of 2 is enough as of now.
In this case, .tbls alone is not a complete set of PHY settings, so either
tbls_hs_overlay[0] or tbls_hs_overlay[1] must be applied on top of the
.tbls to become a complete set of PHY settings.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1703557892-1822-1-git-send-email-quic_cang@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SC7180 UFS PHY is identical to the one found on SM7150. Add a
compatible for it.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: David Wronek <davidwronek@gmail.com>
Link: https://lore.kernel.org/r/20240121-sm7125-upstream-v4-5-f7d1212c8ebb@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
new drivers:
- imagination - new driver for Imagination Technologies GPU
- xe - new driver for Intel GPUs using core drm concepts
core:
- add CLOSE_FB ioctl
- remove old UMS ioctls
- increase max objects to accomodate AMD color mgmt
encoder:
- create per-encoder debugfs directory
edid:
- split out drm_eld
- SAD helpers
- drop edid_firmware module parameter
format-helper:
- cache format conversion buffers
sched:
- move from kthread to workqueue
- rename some internals
- implement dynamic job-flow control
gpuvm:
- provide more features to handle GEM objects
client:
- don't acquire module reference
displayport:
- add mst path property documentation
fdinfo:
- alignment fix
dma-buf:
- add fence timestamp helper
- add fence deadline support
bridge:
- transparent aux-bridge for DP/USB-C
- lt8912b: add suspend/resume support and power regulator support
panel:
- edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
- chromebook panel support
- elida-kd35t133: rework pm
- powkiddy RK2023 panel
- himax-hx8394: drop prepare/unprepare and shutdown logic
- BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G
- Evervision VGG644804, SDC ATNA45AF01
- nv3052c: register docs, init sequence fixes, fascontek FS035VG158
- st7701: Anbernic RG-ARC support
- r63353 panel controller
- Ilitek ILI9805 panel controller
- AUO G156HAN04.0
simplefb:
- support memory regions
- support power domains
amdgpu:
- add new 64-bit sequence number infrastructure
- add AMD specific color management
- ACPI WBRF support for RF interference handling
- GPUVM updates
- RAS updates
- DCN 3.5 updates
- Rework PCIe link speed handling
- Document GPU reset types
- DMUB fixes
- eDP fixes
- NBIO 7.9/7.11 updates
- SubVP updates
- XGMI PCIe state dumping for aqua vanjaram
- GFX11 golden register updates
- enable tunnelling on high pri compute
amdkfd:
- Migrate TLB flushing logic to amdgpu
- Trap handler fixes
- Fix restore workers handling on suspend/resume
- Fix possible memory leak in pqm_uninit()
- support import/export of dma-bufs using GEM handles
radeon:
- fix possible overflows in command buffer checking
- check for errors in ring_lock
i915:
- reorg display code for reuse in xe driver
- fdinfo memory stats printing
- DP MST bandwidth mgmt improvements
- DP panel replay enabling
- MTL C20 phy state verification
- MTL DP DSC fractional bpp support
- Audio fastset support
- use dma_fence interfaces instead of i915_sw_fence
- Separate gem and display code
- AUX register macro refactoring
- Separate display module/device parameters
- Move display capabilities debugfs under display
- Makefile cleanups
- Register cleanups
- Move display lock inits under display/
- VLV/CHV DPIO PHY register and interface refactoring
- DSI VBT sequence refactoring
- C10/C20 PHY PLL hardware readout
- DPLL code cleanups
- Cleanup PXP plane protection checks
- Improve display debug msgs
- PSR selective fetch fixes/improvements
- DP MST fixes
- Xe2LPD FBC restrictions removed
- DGFX uses direct VBT pin mapping
- more MTL WAs
- fix MTL eDP bug
- eliminate use of kmap_atomic
habanalabs:
- sysfs entry to identify a device minor id with debugfs path
- sysfs entry to expose device module id
- add signed device info retrieval through INFO ioctl
- add Gaudi2C device support
- pcie reset prepare/done hooks
msm:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
- Kconfig fix for QMP dependency
- use managed allocators
- DPU: SDM670, SM8650 support
- DPU: Enable SmartDMA on SM8350 and SM8450
- DP: enable runtime PM support
- GPU: add metadata UAPI
- GPU: move devcoredumps to GPU device
- GPU: convert to drm_exec
ivpu:
- update FW API
- new debugfs file
- a new NOP job submission test mode
- improve suspend/resume
- PM improvements
- MMU PT optimizations
- firmware profile frequency support
- support for uncached buffers
- switch to gem shmem helpers
- replace kthread with threaded irqs
rockchip:
- rk3066_hdmi: convert to atomic
- vop2: support nv20 and nv30
- rk3588 support
mediatek:
- use devm_platform_ioremap_resource
- stop using iommu_present
- MT8188 VDOSYS1 display support
panfrost:
- PM improvements
- improve interrupt handling as poweroff
qaic:
- allow to run with single MSI
- support host/device time sync
- switch to persistent DRM devices
exynos:
- fix potential error pointer dereference
- fix wrong error checking
- add missing call to drm_atomic_helper_shutdown
omapdrm:
- dma-fence lockdep annotation fix
tidss:
- dma-fence lockdep annotation fix
- support for AM62A7
v3d:
- BCM2712 - rpi5 support
- fdinfo + gputop support
- uapi for CPU job handling
virtio-gpu:
- add context debug name
-----BEGIN PGP SIGNATURE-----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=nuw0
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This contains two major new drivers:
- imagination is a first driver for Imagination Technologies devices,
it only covers very specific devices, but there is hope to grow it
- xe is a reboot of the i915 GPU (shares display) side using a more
upstream focused development model, and trying to maximise code
sharing. It's not enabled for any hw by default, and will hopefully
get switched on for Intel's Lunarlake.
This also drops a bunch of the old UMS ioctls. It's been dead long
enough.
amdgpu has a bunch of new color management code that is being used in
the Steam Deck.
amdgpu also has a new ACPI WBRF interaction to help avoid radio
interference.
Otherwise it's the usual lots of changes in lots of places.
Detailed summary:
new drivers:
- imagination - new driver for Imagination Technologies GPU
- xe - new driver for Intel GPUs using core drm concepts
core:
- add CLOSE_FB ioctl
- remove old UMS ioctls
- increase max objects to accomodate AMD color mgmt
encoder:
- create per-encoder debugfs directory
edid:
- split out drm_eld
- SAD helpers
- drop edid_firmware module parameter
format-helper:
- cache format conversion buffers
sched:
- move from kthread to workqueue
- rename some internals
- implement dynamic job-flow control
gpuvm:
- provide more features to handle GEM objects
client:
- don't acquire module reference
displayport:
- add mst path property documentation
fdinfo:
- alignment fix
dma-buf:
- add fence timestamp helper
- add fence deadline support
bridge:
- transparent aux-bridge for DP/USB-C
- lt8912b: add suspend/resume support and power regulator support
panel:
- edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
- chromebook panel support
- elida-kd35t133: rework pm
- powkiddy RK2023 panel
- himax-hx8394: drop prepare/unprepare and shutdown logic
- BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G
- Evervision VGG644804, SDC ATNA45AF01
- nv3052c: register docs, init sequence fixes, fascontek FS035VG158
- st7701: Anbernic RG-ARC support
- r63353 panel controller
- Ilitek ILI9805 panel controller
- AUO G156HAN04.0
simplefb:
- support memory regions
- support power domains
amdgpu:
- add new 64-bit sequence number infrastructure
- add AMD specific color management
- ACPI WBRF support for RF interference handling
- GPUVM updates
- RAS updates
- DCN 3.5 updates
- Rework PCIe link speed handling
- Document GPU reset types
- DMUB fixes
- eDP fixes
- NBIO 7.9/7.11 updates
- SubVP updates
- XGMI PCIe state dumping for aqua vanjaram
- GFX11 golden register updates
- enable tunnelling on high pri compute
amdkfd:
- Migrate TLB flushing logic to amdgpu
- Trap handler fixes
- Fix restore workers handling on suspend/resume
- Fix possible memory leak in pqm_uninit()
- support import/export of dma-bufs using GEM handles
radeon:
- fix possible overflows in command buffer checking
- check for errors in ring_lock
i915:
- reorg display code for reuse in xe driver
- fdinfo memory stats printing
- DP MST bandwidth mgmt improvements
- DP panel replay enabling
- MTL C20 phy state verification
- MTL DP DSC fractional bpp support
- Audio fastset support
- use dma_fence interfaces instead of i915_sw_fence
- Separate gem and display code
- AUX register macro refactoring
- Separate display module/device parameters
- Move display capabilities debugfs under display
- Makefile cleanups
- Register cleanups
- Move display lock inits under display/
- VLV/CHV DPIO PHY register and interface refactoring
- DSI VBT sequence refactoring
- C10/C20 PHY PLL hardware readout
- DPLL code cleanups
- Cleanup PXP plane protection checks
- Improve display debug msgs
- PSR selective fetch fixes/improvements
- DP MST fixes
- Xe2LPD FBC restrictions removed
- DGFX uses direct VBT pin mapping
- more MTL WAs
- fix MTL eDP bug
- eliminate use of kmap_atomic
habanalabs:
- sysfs entry to identify a device minor id with debugfs path
- sysfs entry to expose device module id
- add signed device info retrieval through INFO ioctl
- add Gaudi2C device support
- pcie reset prepare/done hooks
msm:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
- Kconfig fix for QMP dependency
- use managed allocators
- DPU: SDM670, SM8650 support
- DPU: Enable SmartDMA on SM8350 and SM8450
- DP: enable runtime PM support
- GPU: add metadata UAPI
- GPU: move devcoredumps to GPU device
- GPU: convert to drm_exec
ivpu:
- update FW API
- new debugfs file
- a new NOP job submission test mode
- improve suspend/resume
- PM improvements
- MMU PT optimizations
- firmware profile frequency support
- support for uncached buffers
- switch to gem shmem helpers
- replace kthread with threaded irqs
rockchip:
- rk3066_hdmi: convert to atomic
- vop2: support nv20 and nv30
- rk3588 support
mediatek:
- use devm_platform_ioremap_resource
- stop using iommu_present
- MT8188 VDOSYS1 display support
panfrost:
- PM improvements
- improve interrupt handling as poweroff
qaic:
- allow to run with single MSI
- support host/device time sync
- switch to persistent DRM devices
exynos:
- fix potential error pointer dereference
- fix wrong error checking
- add missing call to drm_atomic_helper_shutdown
omapdrm:
- dma-fence lockdep annotation fix
tidss:
- dma-fence lockdep annotation fix
- support for AM62A7
v3d:
- BCM2712 - rpi5 support
- fdinfo + gputop support
- uapi for CPU job handling
virtio-gpu:
- add context debug name"
* tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm: (2340 commits)
drm/amd/display: Allow z8/z10 from driver
drm/amd/display: fix bandwidth validation failure on DCN 2.1
drm/amdgpu: apply the RV2 system aperture fix to RN/CZN as well
drm/amd/display: Move fixpt_from_s3132 to amdgpu_dm
drm/amd/display: Fix recent checkpatch errors in amdgpu_dm
Revert "drm/amdkfd: Relocate TBA/TMA to opposite side of VM hole"
drm/amd/display: avoid stringop-overflow warnings for dp_decide_lane_settings()
drm/amd/display: Fix power_helpers.c codestyle
drm/amd/display: Fix hdcp_log.h codestyle
drm/amd/display: Fix hdcp2_execution.c codestyle
drm/amd/display: Fix hdcp_psp.h codestyle
drm/amd/display: Fix freesync.c codestyle
drm/amd/display: Fix hdcp_psp.c codestyle
drm/amd/display: Fix hdcp1_execution.c codestyle
drm/amd/pm/smu7: fix a memleak in smu7_hwmgr_backend_init
drm/amdkfd: Fix iterator used outside loop in 'kfd_add_peer_prop()'
drm/amdgpu: Drop 'fence' check in 'to_amdgpu_amdkfd_fence()'
drm/amdkfd: Confirm list is non-empty before utilizing list_first_entry in kfd_topology.c
drm/amdgpu: Fix '*fw' from request_firmware() not released in 'amdgpu_ucode_request()'
drm/amdgpu: Fix variable 'mca_funcs' dereferenced before NULL check in 'amdgpu_mca_smu_get_mca_entry()'
...
Enable full rate divider configuration support for J784S4_WIZ_10G
for SGMII.
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20231221102956.754617-2-c-vankar@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TI's J784S4 SoC supports SGMII mode with the CPSW9G instance of the CPSW
Ethernet Switch. Thus, enable it by adding SGMII mode to the list of the
corresponding extra_modes member.
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20231221102956.754617-1-c-vankar@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The X1E80100 has three copies of an USB/DP compbo PHY, add support for this
to the Qualcomm QMP PHY driver.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20231201-x1e80100-phy-combo-v1-2-6938ec41f3ac@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
this is used to be compatible with old SoCs, such as mt8195, which shares
t-phy between usb3 and pcie controller, usually, it's default mode is pcie
rc mode, and could use force mode to switch into usb3 mode, because pericfg
layer doesn't provide mode switch, also no efuse or jumper can be used;
Currently, only support switch from default pcie mode to usb3;
Note: don't use this way on new SoCs, use pericfg layer's mode switch
instead (by perperty "mediatek,syscon-type").
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20231211025624.28991-2-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The registers, which are being touched in current SM8550 UFS PHY settings,
and the values being programmed are mainly the ones working for HS-G4 mode,
meanwhile, there are also a few ones somehow taken from HS-G5 PHY settings.
However, even consider HS-G4 mode only, some of them are incorrect and some
are missing. Rectify the HS-G4 PHY settings by strictly aligning with the
SM8550 UFS PHY Hardware Programming Guide suggested HS-G4 PHY settings.
Fixes: 1679bfef90 ("phy: qcom-qmp-ufs: Add SM8550 support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/1701520577-31163-10-git-send-email-quic_cang@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Change the last "depends on GENERIC_PHY" to use select, like the
other 170+ Kconfig users do. This can help prevent circular
dependency issues.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: linux-phy@lists.infradead.org
Link: https://lore.kernel.org/r/20231204234917.23509-1-rdunlap@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add registers to support the 2-port usb2 phy found in RK312x SoC familiy.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20231119121340.109025-3-knaerzche@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 51a9b2c03d ("phy: rockchip-inno-usb2: Handle ID IRQ") added ID
detection interrupt registers. However the current implementation assumes
that falling and rising edge interrupt are always enabled in registers
spanning over subsequent bits.
That is not the case for RK3128's version of the phy and this
implementation can't be used as-is, since there are bits with different
purpose in between.
This splits up the register definitions for id_det_en, id_det_en and
id_det_clr registers in rising and falling edge variants.
It's required as preparation to support RK3128's Innosilicon usb2 phy as
well in this driver and matches pretty much to what the vendor does, so I'm
not expecting issues for other SoCs with that change.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20231119121340.109025-2-knaerzche@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The lowest supported clock frequency of the PHY is 125MHz (see also
mtk_mipi_tx_pll_enable()), but the clamping in .round_rate() has the
wrong minimal value, which will make the .enable() op return -EINVAL on
low frequencies. Fix the minimal clamping value.
Fixes: efda51a58b ("drm/mediatek: add mipi_tx driver for mt8183")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231123110202.2025585-1-mwalle@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When the node for this phy selector is a child node of a syscon node then the
property 'reg' is used as an offset into the parent regmap. When the node
is standalone and gets its own regmap this offset is pre-applied. So we need
to track which method was used to get the regmap and not apply the offset
in the standalone case.
Fixes: 1fdfa7cccd ("phy: ti: gmii-sel: Allow parent to not be syscon node")
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20231025143302.1265633-1-afd@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This reverts commit 134e6d25f6.
The recently added Realtek PHY drivers depend on the new port status
notification mechanism which was built on the deprecated USB PHY
implementation and devicetree binding.
Specifically, using these PHYs would require describing the very same
PHY using both the generic "phy" property and the deprecated "usb-phy"
property which is clearly wrong.
We should not be building new functionality on top of the legacy USB PHY
implementation even if it is currently stuck in some kind of
transitional limbo.
Revert the new Realtek PHY drivers for now so that the port status
notification interface can be reverted and replaced.
Fixes: 134e6d25f6 ("phy: realtek: usb: Add driver for the Realtek SoC USB 2.0 PHY")
Cc: stable@vger.kernel.org # 6.6
Cc: Stanley Chang <stanley_chang@realtek.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231106110654.31090-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit adda6e82a7.
The recently added Realtek PHY drivers depend on the new port status
notification mechanism which was built on the deprecated USB PHY
implementation and devicetree binding.
Specifically, using these PHYs would require describing the very same
PHY using both the generic "phy" property and the deprecated "usb-phy"
property which is clearly wrong.
We should not be building new functionality on top of the legacy USB PHY
implementation even if it is currently stuck in some kind of
transitional limbo.
Revert the new Realtek PHY drivers for now so that the port status
notification interface can be reverted and replaced.
Fixes: adda6e82a7 ("phy: realtek: usb: Add driver for the Realtek SoC USB 3.0 PHY")
Cc: stable@vger.kernel.org # 6.6
Cc: Stanley Chang <stanley_chang@realtek.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231106110654.31090-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GENERIC_PHY can be selected by GENERIC_PHY_MIPI_DPHY directly as
GENERIC_PHY has no dependencies. This way drivers that depend on
GENERIC_PHY_MIPI_DPHY can avoid having to select both --- which they
apparently often omit, too, which further leads to build failures.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20231017080354.538047-1-sakari.ailus@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If probe is reached, we've already matched the device and in the case of
DT matching, the struct device_node pointer will be set. Therefore, there
is no need to call of_match_device() in probe.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231009172923.2457844-16-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Neither of_address.h or of_platform.h are used in the driver, so drop them.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20231009172923.2457844-17-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20231009172923.2457844-15-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other and pull in various other headers. In
preparation to fix this, adjust the includes for what is actually needed.
of_device.h isn't needed, but platform_device.h was implicitly included by
it.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231010205701.1585026-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For all other generations, we have been using just the QPHY prefix for
the PCS registers. Remove the _USB part of the QPHY_USB prefix.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230928105445.1210861-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With gcc 12.3.0, when this file is built, we get errors such as:
drivers/phy/allwinner/phy-sun4i-usb.c: In function ‘sun4i_usb_phy_probe’:
drivers/phy/allwinner/phy-sun4i-usb.c:790:52: error: ‘_vbus’ directive output may be truncated writing 5 bytes into a region of size between 2 and 12 [-Werror=format-truncation=]
790 | snprintf(name, sizeof(name), "usb%d_vbus", i);
| ^~~~~
drivers/phy/allwinner/phy-sun4i-usb.c:790:17: note: ‘snprintf’ output between 10 and 20 bytes into a destination of size 16
790 | snprintf(name, sizeof(name), "usb%d_vbus", i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Because of the possible value of 'i', this can't be an issue in real world
application, but in order to have "make W=1" work correctly, give more
space for 'name'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/0bc81612171baaa6d5dff58c8e009debc03e1ba8.1693735840.git.christophe.jaillet@wanadoo.fr
[vkoul: updated patch title]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The protocol converter configuration registers PCC8, PCCC, PCCD
(implemented by the driver), as well as others, control protocol
converters from multiple lanes (each represented as a different
struct phy). So, if there are simultaneous calls to phy_set_mode_ext()
to lanes sharing the same PCC register (either for the "old" or for the
"new" protocol), corruption of the values programmed to hardware is
possible, because lynx_28g_rmw() has no locking.
Add a spinlock in the struct lynx_28g_priv shared by all lanes, and take
the global spinlock from the phy_ops :: set_mode() implementation. There
are no other callers which modify PCC registers.
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lynx_28g_cdr_lock_check() runs once per second in a workqueue to reset
the lane receiver if the CDR has not locked onto bit transitions in the
RX stream. But the PHY consumer may do stuff with the PHY simultaneously,
and that isn't okay. Block concurrent generic PHY calls by holding the
PHY mutex from this workqueue.
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit added the CDR check work item but didn't cancel it on
the remove path. Fix this by adding a remove function which takes care
of it.
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Realtek SoC USB2 and USB3 PHY Transceivers are only present on
Realtek Digital Home Center (DHC) RTD series SoCs. Hence add a
dependency on ARCH_REALTEK, to prevent asking the user about these
drivers when configuring a kernel without Realtek SoC support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2892527cac9af6fa8f5e7b8daeffd7d4351fde68.1692113167.git.geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are devices in the wild, like the Sony Xperia 1 V that *require*
different tuning than the base design for USB to work.
Add support for overriding the necessary tuning values.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230830-topic-eusb2_override-v2-4-7d8c893d93f6@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Switch to regmap_fields, so that the values written into registers are
sanitized by their explicit sizes and the different registers are
structured in an iterable object to make external changes to the init
sequence simpler.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230830-topic-eusb2_override-v2-2-7d8c893d93f6@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix typo in the description of the 'succesfully'.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230912114646.8452-1-liubo03@inspur.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently, PCS_USB registers that have their initialization data in a
pcs_usb_tbl table are never initialized. Fix that.
Fixes: fc64623637 ("phy: qcom-qmp-combo,usb: add support for separate PCS_USB region")
Reported-by: Adrien Thierry <athierry@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230829-topic-8550_usbphy-v3-2-34ec434194c5@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are two instances of the POWER_STATE_CONFIG1 register: one in
the PCS space and another one in PCS_USB.
The downstream init sequence pokes the latter one while we've been poking
the former one (and misnamed it as the latter one, impostor!). Fix that
up to avoid UB.
Fixes: 49742e9eda ("phy: qcom-qmp-combo: Add support for SM8550")
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230829-topic-8550_usbphy-v3-1-34ec434194c5@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the following Smatch complaint:
drivers/phy/qualcomm/phy-qcom-m31.c:175 m31usb_phy_init()
warn: variable dereferenced before check 'qphy->vreg' (see line 167)
drivers/phy/qualcomm/phy-qcom-m31.c
166
167 ret = regulator_enable(qphy->vreg);
^^^^^^^^^^
Unchecked dereference
168 if (ret) {
169 dev_err(&phy->dev, "failed to enable regulator, %d\n", ret);
170 return ret;
171 }
172
173 ret = clk_prepare_enable(qphy->clk);
174 if (ret) {
175 if (qphy->vreg)
^^^^^^^^^^
Checked too late
176 regulator_disable(qphy->vreg);
177 dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret);
Since the phy will not get registered if qphy->vreg is NULL,
this check is not needed.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-phy/cbd26132-c624-44b7-a073-73222b287338@moroto.mountain/T/#u
Fixes: 08e49af507 ("phy: qcom: Introduce M31 USB PHY driver")
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/1694069452-3794-1-git-send-email-quic_varada@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Both debugfs_create_dir() and debugfs_create_file() return ERR_PTR
and never return NULL.
As Greg suggested, this patch removes the error checking for
debugfs_create_dir in phy-rtk-usb2.c and phy-rtk-usb3.c. This is because
the DebugFS kernel API is developed in a way that the caller can safely
ignore the errors that occur during the creation of DebugFS nodes. The
debugfs APIs have a IS_ERR() judge in start_creating() which can handle it
gracefully. So these checks are unnecessary.
Fixes: 134e6d25f6 ("phy: realtek: usb: Add driver for the Realtek SoC USB 2.0 PHY")
Fixes: adda6e82a7 ("phy: realtek: usb: Add driver for the Realtek SoC USB 3.0 PHY")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230901075231.1368947-1-ruanjinjie@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
m31_ipq5332_regs is only used in phy-qcom-m31.c now, change
it to static.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/20230824092356.1154839-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It should be 'qphy->vreg' passed to PTR_ERR() when devm_regulator_get() fails.
Fixes: 08e49af507 ("phy: qcom: Introduce M31 USB PHY driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/20230824091345.1072650-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Populate offsets configuration for the rest of USB PHYs to make it
possible to switch them to the new (single-node) bindings style.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230824211952.1397699-7-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The register QPHY_V[34]_PCS_MISC_CLAMP_ENABLE is present only on some
SoC families. Other platforms (qcm2290) can have PCS_MISC region, but do
not have this register. Add it to the register layout table and check
that it is defined before toggling CLAMP settings.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230824211952.1397699-5-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All legacy bindings of USB PHYs use "phy", "common" resets, while newer
style bindings use "phy", "phy_phy" resets. In preparation for
converting existing legacy PHY bindings to use newer scheme, drop reset
lists from configuration struture and reference reset lists directly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230824211952.1397699-4-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For the existing PHYs for new binding we are going to drop ref_clk_src
clock and always use ref clock. Rather than introducing additional code
to handle legacy vs current bindings (and clock names), use
devm_clk_bulk_get_optional() when new bindings are used and
devm_clk_bulk_get_all() when legacy bindings are in place.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230824211952.1397699-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For sc8280xp and sa8775p, PCS and PCS_USB initialization data is
described in the same table, thus the pcs_usb offset is not being
applied during initialization of PCS_USB registers. Fix this by adding
the appropriate pcs_usb_tbl tables.
Fixes: 8bd2d6e11c ("phy: qcom-qmp: Add SA8775P USB3 UNI phy")
Fixes: c0c7769cda ("phy: qcom-qmp: Add SC8280XP USB3 UNI phy")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20230828152353.16529-3-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently, PCS_USB registers that have their initialization data in a
pcs_usb_tbl table are never initialized. Fix that.
Fixes: fc64623637 ("phy: qcom-qmp-combo,usb: add support for separate PCS_USB region")
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230828152353.16529-2-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Looks like the driver sleep pins configuration is unusable. Adding the
sleep pins causes the usb phy to not respond. We need to use the default
pins in probe, and only set sleep pins at phy_mdm6600_device_power_off().
As the modem can also be booted to a serial port mode for firmware
flashing, let's make the pin changes limited to probe and remove. For
probe, we get the default pins automatically. We only need to set the
sleep pins in phy_mdm6600_device_power_off() to prevent the modem from
waking up because the gpio line glitches.
If it turns out that we need a separate state for phy_mdm6600_power_on()
and phy_mdm6600_power_off(), we can use the pinctrl idle state.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Fixes: 2ad2af0816 ("phy: mapphone-mdm6600: Improve phy related runtime PM calls")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230913060433.48373-3-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Otherwise we will get an underflow on remove.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Fixes: f7f50b2a7b ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230913060433.48373-2-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit d644e0d798 ("phy: mapphone-mdm6600: Fix PM error handling in
phy_mdm6600_probe") caused a regression where we now unconditionally
disable runtime PM at the end of the probe while it is only needed on
errors.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Miaoqian Lin <linmq006@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fixes: d644e0d798 ("phy: mapphone-mdm6600: Fix PM error handling in phy_mdm6600_probe")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230913060433.48373-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the big set of USB, Thunderbolt, and PHY driver updates for
6.6-rc1. Included in here are:
- PHY driver additions and cleanups
- Thunderbolt minor additions and fixes
- USB MIDI 2 gadget support added
- dwc3 driver updates and additions
- Removal of some old USB wireless code that was missed when that
codebase was originally removed a few years ago, cleaning up some
core USB code paths
- USB core potential use-after-free fixes that syzbot from different
people/groups keeps tripping over
- typec updates and additions
- gadget fixes and cleanups
- loads of smaller USB core and driver cleanups all over the place
Full details are in the shortlog. All of these have been in linux-next
for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPIAOQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn80gCgybzMp0YnSildFetSC8lUJTnzjQcAn3KWzb75
Zt72jxGl4ZOXHEpozG4O
=FLrK
-----END PGP SIGNATURE-----
Merge tag 'usb-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt / PHY driver updates from Greg KH:
"Here is the big set of USB, Thunderbolt, and PHY driver updates for
6.6-rc1. Included in here are:
- PHY driver additions and cleanups
- Thunderbolt minor additions and fixes
- USB MIDI 2 gadget support added
- dwc3 driver updates and additions
- Removal of some old USB wireless code that was missed when that
codebase was originally removed a few years ago, cleaning up some
core USB code paths
- USB core potential use-after-free fixes that syzbot from different
people/groups keeps tripping over
- typec updates and additions
- gadget fixes and cleanups
- loads of smaller USB core and driver cleanups all over the place
Full details are in the shortlog. All of these have been in linux-next
for a while with no reported problems"
* tag 'usb-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
platform/chrome: cros_ec_typec: Configure Retimer cable type
tcpm: Avoid soft reset when partner does not support get_status
usb: typec: tcpm: reset counter when enter into unattached state after try role
usb: typec: tcpm: set initial svdm version based on pd revision
USB: serial: option: add FOXCONN T99W368/T99W373 product
USB: serial: option: add Quectel EM05G variant (0x030e)
usb: dwc2: add pci_device_id driver_data parse support
usb: gadget: remove max support speed info in bind operation
usb: gadget: composite: cleanup function config_ep_by_speed_and_alt()
usb: gadget: config: remove max speed check in usb_assign_descriptors()
usb: gadget: unconditionally allocate hs/ss descriptor in bind operation
usb: gadget: f_uvc: change endpoint allocation in uvc_function_bind()
usb: gadget: add a inline function gether_bitrate()
usb: gadget: use working speed to calcaulate network bitrate and qlen
dt-bindings: usb: samsung,exynos-dwc3: Add Exynos850 support
usb: dwc3: exynos: Add support for Exynos850 variant
usb: gadget: udc-xilinx: fix incorrect type in assignment warning
usb: gadget: udc-xilinx: fix cast from restricted __le16 warning
usb: gadget: udc-xilinx: fix restricted __le16 degrades to integer warning
USB: dwc2: hande irq on dead controller correctly
...
changes to the clk framework this time around. That's probably because everyone
was on vacation (yours truly included). We did lose a couple clk drivers this
time around because nobody was using those devices. That skews the diffstat a
bit, but either way, nothing looks out of the ordinary here. The usual suspects
are chugging along adding support for more SoCs and fixing bugs.
If I had to choose, I'd say the theme for the past few months has been
"polish". There's quite a few patches that migrate to
devm_platform_ioremap_resource() in here. And there's more than a handful of
patches that move the NR_CLKS define from the DT binding header to the driver.
There's even patches that migrate drivers to use clk_parent_data and clk_hw to
describe clk tree topology. It seems that the spring (summer?) cleaning bug got
some folks, or the semiconductor shortage finally hit the software side.
New Drivers:
- StarFive JH7110 SoC clock drivers
- Qualcomm IPQ5018 Global Clock Controller driver
- Versa3 clk generator to support 48KHz playback/record with audio codec on
RZ/G2L SMARC EVK
Removed Drivers:
- Remove non-OF mmp clk drivers
- Remove OXNAS clk driver
Updates:
- Add __counted_by to struct clk_hw_onecell_data and struct spmi_pmic_div_clk_cc
- Move defines for numbers of clks (NR_CLKS) from DT headers to drivers
- Introduce kstrdup_and_replace() and use it
- Add PLL rates for Rockchip rk3568
- Add the display clock tree for Rockchip rv1126
- Add Audio Clock Generator (ADG) clocks on Renesas R-Car Gen3 and RZ/G2 SoCs
- Convert sun9i-mmc clock to use devm_platform_get_and_ioremap_resource()
- Fix function name in a comment in ccu_mmc_timing.c
- Parameter name correction for ccu_nkm_round_rate()
- Implement CLK_SET_RATE_PARENT for Allwinner NKM clocks, i.e. consider alternative
parent rates when determining clock rates
- Set CLK_SET_RATE_PARENT for Allwinner A64 pll-mipi
- Support finding closest (as opposed to closest but not higher) clock rate
for NM, NKM, mux and div type clocks, as use it for Allwinner A64 pll-video0
- Prefer current parent rate if able to generate ideal clock rate for Allwinner NKM clocks
- Clean up Qualcomm SMD RPM driver, with interconnect bus clocks moved out to
the interconnect drivers
- Fix various PM runtime bugs across many Qualcomm clk drivers
- Migrate Qualcomm MDM9615 is to parent_hw and parent_data
- Add network related resets on Qualcomm IPQ4019
- Add a couple missing USB related clocks to Qualcomm IPQ9574
- Add missing gpll0_sleep_clk_src to Qualcomm MSM8917 global clock controller
- In the Qualcomm QDU1000 global clock controller, GDSCs, clkrefs, and GPLL1 are
added, while PCIe pipe clock, SDCC rcg ops are corrected
- Add missing GDSCs to and correct GDSCs for the SC8280XP global clock controller driver
- Support retention for the Qualcomm SC8280XP display clock controller GDSCs.
- Qualcommm's SDCC apps_clk_src is marked with CLK_OPS_PARENT_ENABLE to fix
issues with missing parent clocks across sc7180, sm7150, sm6350 and sm8250,
while sm8450 is corrected to use floor ops
- Correct Qualcomm SM6350 GPU clock controller's clock supplies
- Drop unwanted clocks from the Qualcomm IPQ5332 GCC driver
- Add missing OXILICX GDSC to Qualcomm MSM8226 GCC
- Change the delay in the Qualcomm reset controller to fsleep() for correctness
- Extend the Qualcomm SM83550 Video clock controller to support SC8280XP
- Add graphics clock support on Renesas RZ/G2M, RZ/G2N, RZ/G2E, and R-Car H3,
M3-W, and M3-N SoCs
- Add Clocked Serial Interface (CSI) clocks on Renesas RZ/V2M
- Add PWM (MTU3) clock and reset on Renesas RZ/G2UL and RZ/Five
- Add the PDM IPC clock for i.MX93
- Add 519.75MHz frequency support for i.MX9 PLL
- Simplify the .determine_rate() implementation for i.MX GPR mux
- Make the i.MX8QXP LPCG clock use devm_platform_ioremap_resource()
- Add the audio mux clock to i.MX8
- Fix the SPLL2 MULT range for PLLv4
- Update the SPLL2 type in i.MX8ULP
- Fix the SAI4 clock on i.MX8MP
- Add silicon revision print for i.MX25 on clocks init
- Drop the return value from __mx25_clocks_init()
- Fix the clock pauses on no-op set_rate for i.MX8M composite clock
- Drop restrictions for i.MX PLL14xx and fix its max prediv value
- Drop the 393216000 and 361267200 from i.MX PLL14xx rate table to allow
glitch free switching
-----BEGIN PGP SIGNATURE-----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=h2Jz
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk subsystem updates from Stephen Boyd:
"This pull request is full of clk driver changes. In fact, there aren't
any changes to the clk framework this time around. That's probably
because everyone was on vacation (yours truly included). We did lose a
couple clk drivers this time around because nobody was using those
devices. That skews the diffstat a bit, but either way, nothing looks
out of the ordinary here. The usual suspects are chugging along adding
support for more SoCs and fixing bugs.
If I had to choose, I'd say the theme for the past few months has been
"polish". There's quite a few patches that migrate to
devm_platform_ioremap_resource() in here. And there's more than a
handful of patches that move the NR_CLKS define from the DT binding
header to the driver. There's even patches that migrate drivers to use
clk_parent_data and clk_hw to describe clk tree topology. It seems
that the spring (summer?) cleaning bug got some folks, or the
semiconductor shortage finally hit the software side.
New Drivers:
- StarFive JH7110 SoC clock drivers
- Qualcomm IPQ5018 Global Clock Controller driver
- Versa3 clk generator to support 48KHz playback/record with audio
codec on RZ/G2L SMARC EVK
Removed Drivers:
- Remove non-OF mmp clk drivers
- Remove OXNAS clk driver
Updates:
- Add __counted_by to struct clk_hw_onecell_data and struct
spmi_pmic_div_clk_cc
- Move defines for numbers of clks (NR_CLKS) from DT headers to
drivers
- Introduce kstrdup_and_replace() and use it
- Add PLL rates for Rockchip rk3568
- Add the display clock tree for Rockchip rv1126
- Add Audio Clock Generator (ADG) clocks on Renesas R-Car Gen3 and
RZ/G2 SoCs
- Convert sun9i-mmc clock to use
devm_platform_get_and_ioremap_resource()
- Fix function name in a comment in ccu_mmc_timing.c
- Parameter name correction for ccu_nkm_round_rate()
- Implement CLK_SET_RATE_PARENT for Allwinner NKM clocks, i.e.
consider alternative parent rates when determining clock rates
- Set CLK_SET_RATE_PARENT for Allwinner A64 pll-mipi
- Support finding closest (as opposed to closest but not higher)
clock rate for NM, NKM, mux and div type clocks, as use it for
Allwinner A64 pll-video0
- Prefer current parent rate if able to generate ideal clock rate for
Allwinner NKM clocks
- Clean up Qualcomm SMD RPM driver, with interconnect bus clocks
moved out to the interconnect drivers
- Fix various PM runtime bugs across many Qualcomm clk drivers
- Migrate Qualcomm MDM9615 is to parent_hw and parent_data
- Add network related resets on Qualcomm IPQ4019
- Add a couple missing USB related clocks to Qualcomm IPQ9574
- Add missing gpll0_sleep_clk_src to Qualcomm MSM8917 global clock
controller
- In the Qualcomm QDU1000 global clock controller, GDSCs, clkrefs,
and GPLL1 are added, while PCIe pipe clock, SDCC rcg ops are
corrected
- Add missing GDSCs to and correct GDSCs for the SC8280XP global
clock controller driver
- Support retention for the Qualcomm SC8280XP display clock
controller GDSCs.
- Qualcommm's SDCC apps_clk_src is marked with CLK_OPS_PARENT_ENABLE
to fix issues with missing parent clocks across sc7180, sm7150,
sm6350 and sm8250, while sm8450 is corrected to use floor ops
- Correct Qualcomm SM6350 GPU clock controller's clock supplies
- Drop unwanted clocks from the Qualcomm IPQ5332 GCC driver
- Add missing OXILICX GDSC to Qualcomm MSM8226 GCC
- Change the delay in the Qualcomm reset controller to fsleep() for
correctness
- Extend the Qualcomm SM83550 Video clock controller to support
SC8280XP
- Add graphics clock support on Renesas RZ/G2M, RZ/G2N, RZ/G2E, and
R-Car H3, M3-W, and M3-N SoCs
- Add Clocked Serial Interface (CSI) clocks on Renesas RZ/V2M
- Add PWM (MTU3) clock and reset on Renesas RZ/G2UL and RZ/Five
- Add the PDM IPC clock for i.MX93
- Add 519.75MHz frequency support for i.MX9 PLL
- Simplify the .determine_rate() implementation for i.MX GPR mux
- Make the i.MX8QXP LPCG clock use devm_platform_ioremap_resource()
- Add the audio mux clock to i.MX8
- Fix the SPLL2 MULT range for PLLv4
- Update the SPLL2 type in i.MX8ULP
- Fix the SAI4 clock on i.MX8MP
- Add silicon revision print for i.MX25 on clocks init
- Drop the return value from __mx25_clocks_init()
- Fix the clock pauses on no-op set_rate for i.MX8M composite clock
- Drop restrictions for i.MX PLL14xx and fix its max prediv value
- Drop the 393216000 and 361267200 from i.MX PLL14xx rate table to
allow glitch free switching"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (207 commits)
clk: qcom: Fix SM_GPUCC_8450 dependencies
clk: lmk04832: Support using PLL1_LD as SPI readback pin
clk: lmk04832: Don't disable vco clock on probe fail
clk: lmk04832: Set missing parent_names for output clocks
clk: mvebu: Convert to devm_platform_ioremap_resource()
clk: nuvoton: Convert to devm_platform_ioremap_resource()
clk: socfpga: agilex: Convert to devm_platform_ioremap_resource()
clk: ti: Use devm_platform_get_and_ioremap_resource()
clk: mediatek: Convert to devm_platform_ioremap_resource()
clk: hsdk-pll: Convert to devm_platform_ioremap_resource()
clk: gemini: Convert to devm_platform_ioremap_resource()
clk: fsl-sai: Convert to devm_platform_ioremap_resource()
clk: bm1880: Convert to devm_platform_ioremap_resource()
clk: axm5516: Convert to devm_platform_ioremap_resource()
clk: actions: Convert to devm_platform_ioremap_resource()
clk: cdce925: Remove redundant of_match_ptr()
clk: pxa910: Move number of clocks to driver source
clk: pxa1928: Move number of clocks to driver source
clk: pxa168: Move number of clocks to driver source
clk: mmp2: Move number of clocks to driver source
...
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct clk_hw_onecell_data.
Additionally, since the element count member must be set before accessing
the annotated flexible array member, move its initialization earlier.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Taichi Sugaya <sugaya.taichi@socionext.com>
Cc: Takao Orito <orito.takao@socionext.com>
Cc: Qin Jian <qinjian@cqplus1.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-sunxi@lists.linux.dev
Cc: linux-phy@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230817203019.never.795-kees@kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Implement Exynos850 USB 2.0 DRD PHY controller support. Exynos850 has
quite a different PHY controller than Exynos5 compatible controllers,
but it's still possible to implement it on top of existing
exynos5-usbdrd driver infrastructure.
Only UTMI+ (USB 2.0) PHY interface is implemented, as Exynos850 doesn't
support USB 3.0.
Only two clocks are used for this controller:
- phy: bus clock, used for PHY registers access
- ref: PHY reference clock (OSCCLK)
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230819031731.22618-7-semen.protsenko@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Modern Exynos chips (like Exynos850) might have 26 MHz OSCCLK external
clock, which is also used as a PHY reference clock. For some USB PHY
controllers (e.g USB DRD PHY block on Exynos850) there is no need to set
the refclk frequency at all (and corresponding bits in CLKRSTCTRL[7:5]
are marked RESERVED), so that value won't be set in the driver. But
even in that case, 26 MHz support still has to be added, otherwise
exynos5_rate_to_clk() fails, which leads in turn to probe error.
Add the correct value for 26MHz refclk to make it possible to add
support for new Exynos USB DRD PHY controllers.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230819031731.22618-6-semen.protsenko@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Provide a way to use different PHY ops for different chips. Right now
all chips are using exynos5_usbdrd_phy_ops, but it won't always be the
case. For example, Exynos850 has very different USB PHY block, so there
will be another PHY ops implementation for that chip.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230819031731.22618-5-semen.protsenko@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
During rebase of qcom-qmp-combo series a call to devm_clk_bulk_get_all()
got moved by git from qmp_combo_parse_dt_legacy() to
phy_dp_clks_register(). This doesn't have any serious effect, since the
clocks will be set in both legacy and non-legacy paths. However let's
move it back to place anyway, to prevent the driver from fetching clocks
twice.
Fixes: 28e265bf84 ("phy: qcom-qmp-combo: simplify clock handling")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820235813.562284-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reuse sm8250 configuration to add support for both single lane and dual
lane PCIe PHYs on the Qualcomm SM8150 platform.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-8-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Populate offsets configuration for the rest of UFS PHYs to make it
possible to switch them to the new (single-node) bindings style.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-7-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For some of existing PHYs for new binding we are going to change refgen
to more correct "rchng". Rather than introducing additional code
to handle legacy vs current bindings (and clock names), use
devm_clk_bulk_get_optional().
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-6-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In order to simplify adding new PHY configurations, keep register
offset structs sorted by the version.
Fixes: a05b6d5135 ("phy: qcom-qmp-pcie: add support for sa8775p")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-5-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no shared lane config for v5.20 PHYs, it is only present on
SM8550 gen4x2.
Fixes: a05b6d5135 ("phy: qcom-qmp-pcie: add support for sa8775p")
Cc: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-4-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This adds an error message if getting vbus failed for some reason,
-EPROBE_DEFER is handled appropriately as well and adds a nice
information to debugfs.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20230816080256.611380-1-alexander.stein@ew.tq-group.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for Rockchip RV1126 DSI-DPHY.
The existing 2.5GHz phy timing table added for RK3568 is working
as it is for RV1126 as well.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230731110012.2913742-5-jagan@edgeble.ai
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'soc_id' is an enum, thus cast of pointer on 64-bit compile test with
W=1 causes:
phy-meson-g12a-usb2.c:322:17: error: cast to smaller integer type 'enum meson_soc_id' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230810091310.70231-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'version' is an enum, thus cast of pointer on 64-bit compile test with
W=1 causes:
phy-pxa-usb.c:299:26: error: cast to smaller integer type 'enum pxa_usb_phy_version' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810111958.205705-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'version' is an enum, thus cast of pointer on 64-bit compile test with
W=1 causes:
phy-bcm-sr-usb.c:314:13: error: cast to smaller integer type 'enum bcm_usb_phy_version' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810111958.205705-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'family' is an enum, thus cast of pointer on 64-bit compile test with
W=1 causes:
drivers/phy/broadcom/phy-bcm-ns-usb3.c:209:17: error: cast to smaller integer type 'enum bcm_ns_family' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810111958.205705-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'version' is an enum, thus cast of pointer on 64-bit compile test with
W=1 causes:
phy-brcm-sata.c:775:19: error: cast to smaller integer type 'enum brcm_sata_phy_version' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810111958.205705-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The conversion commit 7559e7572c ("phy: Explicitly include correct DT
includes") misses offsets configuration for sm8150 (most likely it was
developed separately from the series adding HS G4 support and was not
adapted for the sm8150/sm8250 configuration split).
Add missing offsets to sm8150_ufsphy_cfg.
Fixes: 7559e7572c ("phy: Explicitly include correct DT includes")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230731111009.3998089-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are following smatch warning:
drivers/phy/realtek/phy-rtk-usb2.c:901 get_phy_data_by_efuse()
error: 'buf' dereferencing possible ERR_PTR()
drivers/phy/realtek/phy-rtk-usb2.c:942 get_phy_data_by_efuse()
error: 'buf' dereferencing possible ERR_PTR()
drivers/phy/realtek/phy-rtk-usb3.c:460
get_phy_data_by_efuse() error: 'buf' dereferencing possible ERR_PTR()
The nvmem_cell_read may fail to read. So, driver must handle failure cases.
Fixes: 134e6d25f6 ("phy: realtek: usb: Add driver for the Realtek SoC USB 2.0 PHY")
Fixes: adda6e82a7 ("phy: realtek: usb: Add driver for the Realtek SoC USB 3.0 PHY")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-phy/e7ff2870-c30c-4d8d-a7a9-d2d6a4962eb5@kadam.mountain/
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230801071509.20096-1-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here for testing and for other patches to be
applied on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When USB_COMMON are not enabled, phy-rtk-usb2 and phy-rtk-usb3 suffers
a build error due to a missing usb_debug_root that is provided
by CONFIG_USB_COMMON, so make the driver select USB_COMMON.
or1k-linux-ld: drivers/phy/realtek/phy-rtk-usb2.o: in function `create_phy_debug_root':
>> drivers/phy/realtek/phy-rtk-usb2.c:715: undefined reference to `usb_debug_root'
>> or1k-linux-ld: drivers/phy/realtek/phy-rtk-usb2.c:715: undefined reference to `usb_debug_root'
or1k-linux-ld: drivers/phy/realtek/phy-rtk-usb3.o: in function `create_phy_debug_root':
>> drivers/phy/realtek/phy-rtk-usb3.c:349: undefined reference to `usb_debug_root'
>> or1k-linux-ld: drivers/phy/realtek/phy-rtk-usb3.c:349: undefined reference to `usb_debug_root'
Fixes: 134e6d25f6 ("phy: realtek: usb: Add driver for the Realtek SoC USB 2.0 PHY")
Fixed: adda6e82a7 ("phy: realtek: usb: Add driver for the Realtek SoC USB 3.0 PHY")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202307290733.weSlHrGp-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202307291022.3pVeTR9z-lkp@intel.com/
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230729053029.6226-1-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The various StarFive PHYs are only present on StarFive SoCs. Hence add
a dependency on ARCH_STARFIVE, to prevent asking the user about these
drivers when configuring a kernel without StarFive SoC support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Link: https://lore.kernel.org/r/12097f6107a18e2f7cfb80f47ac7b27808e062c4.1690300076.git.geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller. Added the driver to drive the USB 3.0 PHY transceivers.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230725033318.8361-3-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller. Added the driver to drive the USB 2.0 PHY transceivers.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230725033318.8361-2-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to support newer style bindings for combo PHYs, populate
offsets for all Combo QMP PHY configurations.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230711120916.4165894-4-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For the existing PHYs for new binding we are going to drop ref_clk_src
clock and always use ref clock. Rather than introducing additional code
to handle legacy vs current bindings (and clock names), use
devm_clk_bulk_get_optional() when new bindings are used and
devm_clk_bulk_get_all() when legacy bindings are in place.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230711120916.4165894-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The size of array 'priv->ports[]' is INNO_PHY_PORT_NUM.
In the for loop, 'i' is used as the index for array 'priv->ports[]'
with a check (i > INNO_PHY_PORT_NUM) which indicates that
INNO_PHY_PORT_NUM is allowed value for 'i' in the same loop.
This > comparison needs to be changed to >=, otherwise it potentially leads
to an out of bounds write on the next iteration through the loop
Fixes: ba8b0ee81f ("phy: add inno-usb2-phy driver for hi3798cv200 SoC")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230721090558.3588613-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add mipi dphy rx support for the StarFive JH7110 SoC. It is used to
transfer CSI camera data.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Reviewed-by: Minda Chen <minda.chen@starfivetech.com>
Link: https://lore.kernel.org/r/20230718070803.16660-3-changhuang.liang@starfivetech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/phy/phy-can-transceiver.c
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20230714174841.4061919-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If the parent node is not a syscon type, then fallback and check
if we can get a regmap from our own node. This no longer forces
us to make the parent of this node a syscon node when that might
not be appropriate.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20230713200957.134480-1-afd@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Due to limited available frequency ratios, the reference clock rate may
not be exactly the same as the required rate. Allow a small (100 ppm)
deviation.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20230711194542.898230-1-sean.anderson@seco.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Populate offsets configuration for the rest of UFS PHYs to make it
possible to switch them to the new (single-node) bindings style.
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230711145153.4167820-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add single link SGMII register configuration for no SSC for
cdns,sierra-phy-t0 compatibility string.
The configuration is based on Sierra Programmer's Guide and
validated in Cisco CrayAR SoC.
Co-developed-by: Bartosz Wawrzyniak <bwawrzyn@cisco.com>
Signed-off-by: Bartosz Wawrzyniak <bwawrzyn@cisco.com>
Signed-off-by: Marcin Wierzbicki <mawierzb@cisco.com>
Link: https://lore.kernel.org/r/20230626105533.2999966-1-mawierzb@cisco.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This adds a bunch of new pixel clock- and tmds rates to the pre-pll
table which are required to get more VESA and some DMT rates working.
It has been completely re-calculated to match the min- and max-vco of
(750 MHz - 3.2 GHz) requirements. If more than one configuration would
have been possible the lowest fbdiv and refdiv (and therefore lowest
vco rate) has been preferred.
It's important to note, that RK3228 version of the phy does not support
fractional dividers. To support the most possible rates for this version
also in both 8-bit and 10-bit variant, some rates are not exact. The
maximum deviation of the pixel clock is 0.26, which perfectly fits into
VESA DMT recommendation of 0.5%.
I tested all possible rates on several screens from different
manufacturers with both RK3228 and RK3328. Both pre- and post-PLL
locking are slighlty faster now.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-7-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Regular 8-bit and Deep Color video formats mainly differ in TMDS rate and
not in pixel clock rate.
When the hdmiphy clock is configured with the same pixel clock rate using
clk_set_rate() the clock framework do not signal the hdmi phy driver
to set_rate when switching between 8-bit and Deep Color.
This result in pre/post pll not being re-configured when switching between
regular 8-bit and Deep Color video formats.
Fix this by calling set_rate in power_on to force pre pll re-configuration.
Signed-off-by: Huicong Xu <xhc@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-6-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
inno_write is used to configure 0xaa reg, that also hold the
POST_PLL_POWER_DOWN bit.
When POST_PLL_REFCLK_SEL_TMDS is configured the power down bit is not
taken into consideration.
Fix this by keeping the power down bit until configuration is complete.
Also reorder the reg write order for consistency.
Fixes: 53706a1168 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-5-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
inno_hdmi_phy_rk3328_clk_recalc_rate() is returning a rate not found
in the pre pll config table when the fractal divider is used.
This can prevent proper power_on because a tmdsclock for the new rate
is not found in the pre pll config table.
Fix this by saving and returning a rounded pixel rate that exist
in the pre pll config table.
Fixes: 53706a1168 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-3-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
inno_hdmi_phy_rk3328_clk_set_rate() is using the RK3228 macro
when configuring vco_div_5 on RK3328.
Fix this by using correct vco_div_5 macro for RK3328.
Fixes: 53706a1168 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-2-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The only difference between qmp_v6_dp_aux_init() and
qmp_v4_dp_aux_init() is the address of COM_BIAS_EN_CLKBUFLR_EN register.
Move it to register layout and drop the duplicate function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230621153317.1025914-7-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The functions qmp_v5_configure_dp_phy() and qmp_v6_configure_dp_phy()
are now copies of qmp_v4_configure_dp_phy(). Drop them and use the v4
function in all the cases.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230621153317.1025914-6-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use register layout for TX_HIGHZ_DRVR_EN and TX_TRANSCEIVER_BIAS_EN
registers. This will allow us to unify qmp_v[456]_configure_dp_phy()
functions in the next commit.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230621153317.1025914-5-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It seems the commit a2e927b0e5 ("phy: qcom-qmp-combo: Add sc8280xp
USB/DP combo phys") contained a typo for selecting bias0_en values.
First, bias0_en and bias1_en are expected to be symmetrical, and then
the vendor driver also uses `flipped : 0x3E : 0x15` statement for
bias0_en. Correct bias0_en programming to follow this.
Fixes: 49742e9eda ("phy: qcom-qmp-combo: Add support for SM8550")
Fixes: a2e927b0e5 ("phy: qcom-qmp-combo: Add sc8280xp USB/DP combo phys")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230621153317.1025914-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Enabling clock for all the lanes consumes power even PHY is active or
inactive. To resolve this, enable/disable clocks in phy_init/phy_exit.
By default clock is disabled for all the lanes. Whenever phy_init called
from USB, SATA, or display driver, etc. It enabled the required clock
for requested lane. On phy_exit cycle, it disabled clock for the active
PHYs.
During the suspend/resume cycle, each USB/ SATA/ display driver called
phy_exit/phy_init individually. It disabled clock on exit, and enabled
on initialization for the active PHYs.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20230613140250.3018947-3-piyush.mehta@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Added Runtime power management support to the xilinx phy driver and using
DEFINE_RUNTIME_DEV_PM_OPS new macros allows the compiler to remove the
unused dev_pm_ops structure and related functions if !CONFIG_PM without
the need to mark the functions __maybe_unused.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20230613140250.3018947-2-piyush.mehta@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All of the entries do fit in a maximum of 82 columns, which is
acceptable. While at it, also remove the useless comma on the
last entry and add the usual sentinel comment.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230525115258.90091-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Switch to devm_of_clk_add_hw_provider() in the probe function: this
also allows to entirely remove the .remove_new() callback, as its
only task was to unregister the clock provider.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230525115258.90091-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of registering a struct clk, directly register clk_hw: this
allows us to cleanup a pointer to struct clk from struct mtk_mipi_tx.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230525115258.90091-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When adding support for some of the platforms (sc7180, sc8180x, sdm845,
sm8[1234]50), we added USB PHYs for the combo USB+DP QMP PHYs. Now all
such usecases were migrated to use USB+DP Combo driver. To simplify the
qcom-qmp-usb PHY driver split the legacy USB+dp_com support into a
separate driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230531023415.1209301-6-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Printing the OF node is not useful, since we get the same information
from the device context. Instead print the reg address, that could
not be found.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230522170324.61349-8-sebastian.reichel@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify the code by directly getting the match data via
device_get_match_data() instead of open coding its functionality.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230522170324.61349-7-sebastian.reichel@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify phyclk handling by using devm_clk_get_optional_enabled to
acquire and enable the optional clock. This also fixes a resource
leak in driver remove path and adds proper error handling.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230522170324.61349-6-sebastian.reichel@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On RK3588 some registers need to be tweaked to support waking up from
suspend when a USB device is plugged into a port from a suspended PHY.
Without this change USB devices only work when they are plugged at
boot time.
Apart from that it optimizes settings to avoid devices toggling
between fullspeed and highspeed mode.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230522170324.61349-5-sebastian.reichel@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add basic support for the USB2 PHY found in the Rockchip RK3588.
Co-developed-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230522170324.61349-3-sebastian.reichel@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of a 3D matrix use a key:value pair table for link_cmn_vals,
xcvr_diag_vals, pcs_cmn_vals, phy_pma_cmn_vals, cmn_vals,
tx_ln_vals and rx_ln_vals. This makes it scaleable for multiple
reference clocks.
Wherever both CDNS and TI use the same settings, reuse the same data.
Introduce CLK_ANY and ANY_SSC enums which are used if the setting
is independent of clock rate or SSC type.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20230530143853.26571-3-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705090126.26854-2-frank.li@vivo.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705090126.26854-1-frank.li@vivo.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The return value from qcom_snps_hsphy_suspend/resume is not used. Make
sure qcom_snps_hsphy_runtime_suspend/resume return this value as well.
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20230629144542.14906-4-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver is not enabling the ref clock, which thus gets disabled by
the clk_disable_unused() initcall. This leads to the dwc3 controller
failing to initialize if probed after clk_disable_unused() is called,
for instance when the driver is built as a module.
To fix this, switch to the clk_bulk API to handle both cfg_ahb and ref
clocks at the proper places.
Note that the cfg_ahb clock is currently not used by any device tree
instantiation of the PHY. Work needs to be done separately to fix this.
Link: https://lore.kernel.org/linux-arm-msm/ZEqvy+khHeTkC2hf@fedora/
Fixes: 51e8114f80 ("phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs")
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20230629144542.14906-3-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the dwc3 core, both system and runtime suspend end up calling
dwc3_suspend_common(). From there, what happens for the PHYs depends on
the USB mode and whether the controller is entering system or runtime
suspend.
HOST mode:
(1) system suspend on a non-wakeup-capable controller
The [1] if branch is taken. dwc3_core_exit() is called, which ends up
calling phy_power_off() and phy_exit(). Those two functions decrease the
PM runtime count at some point, so they will trigger the PHY runtime
sleep (assuming the count is right).
(2) runtime suspend / system suspend on a wakeup-capable controller
The [1] branch is not taken. dwc3_suspend_common() calls
phy_pm_runtime_put_sync(). Assuming the ref count is right, the PHY
runtime suspend op is called.
DEVICE mode:
dwc3_core_exit() is called on both runtime and system sleep
unless the controller is already runtime suspended.
OTG mode:
(1) system suspend : dwc3_core_exit() is called
(2) runtime suspend : do nothing
In host mode, the code seems to make a distinction between 1) runtime
sleep / system sleep for wakeup-capable controller, and 2) system sleep
for non-wakeup-capable controller, where phy_power_off() and phy_exit()
are only called for the latter. This suggests the PHY is not supposed to
be in a fully powered-off state for runtime sleep and system sleep for
wakeup-capable controller.
Moreover, downstream, cfg_ahb_clk only gets disabled for system suspend.
The clocks are disabled by phy->set_suspend() [2] which is only called
in the system sleep path through dwc3_core_exit() [3].
With that in mind, don't disable the clocks during the femto PHY runtime
suspend callback. The clocks will only be disabled during system suspend
for non-wakeup-capable controllers, through dwc3_core_exit().
[1] https://elixir.bootlin.com/linux/v6.4/source/drivers/usb/dwc3/core.c#L1988
[2] https://git.codelinaro.org/clo/la/kernel/msm-5.4/-/blob/LV.AU.1.2.1.r2-05300-gen3meta.0/drivers/usb/phy/phy-msm-snps-hs.c#L524
[3] https://git.codelinaro.org/clo/la/kernel/msm-5.4/-/blob/LV.AU.1.2.1.r2-05300-gen3meta.0/drivers/usb/dwc3/core.c#L1915
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20230629144542.14906-2-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The pll prediv calculus searchs for the smallest prediv that gets
the ns_hdmipll_ck in the range of 5 GHz to 12 GHz.
A typo in the upper bound test was testing for 5Ghz to 1Ghz
Fixes: 45810d486b ("phy: mediatek: add support for phy-mtk-hdmi-mt8195")
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230529-hdmi_phy_fix-v1-1-bf65f53af533@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- New Support
- Debugfs support for phy core and mediatek driver
- Hisilicon inno-usb2-phy driver supporting Hi3798MV100
- Qualcomm SGMII SerDes PHY driver, SM6115 & QCM2290 QMP-USB support,
SA8775P USB PHY & USB3 UNI support, QUSB2 support for IPQ9574, IPQ9574 USB3 PHY
- Updates
- Sparx5 serdes phy power optimzation
- cadence salvo usb properties and updates and torrent DP with PCIe &
USB support
- Yaml conversion for Broadcom kona USB bindings and MXS USB binding
-----BEGIN PGP SIGNATURE-----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=ReXo
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.5_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New Support:
- Debugfs support for phy core and mediatek driver
- Hisilicon inno-usb2-phy driver supporting Hi3798MV100
- Qualcomm SGMII SerDes PHY driver, SM6115 & QCM2290 QMP-USB support,
SA8775P USB PHY & USB3 UNI support, QUSB2 support for IPQ9574,
IPQ9574 USB3 PHY
UpdatesL
- Sparx5 serdes phy power optimzation
- cadence salvo usb properties and updates and torrent DP with PCIe &
USB support
- Yaml conversion for Broadcom kona USB bindings and MXS USB binding"
* tag 'phy-for-6.5_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (67 commits)
dt-bindings: phy: brcm,brcmstb-usb-phy: Fix error in "compatible" conditional schema
dt-bindings: phy: mixel,mipi-dsi-phy: Remove assigned-clock* properties
dt-bindings: phy: intel,combo-phy: restrict node name suffixes
dt-bindings: phy: qcom,usb-hs-phy: Add compatible
phy: tegra: xusb: check return value of devm_kzalloc()
phy: qcom: qmp-combo: fix Display Port PHY configuration for SM8550
phy: qcom: add the SGMII SerDes PHY driver
dt-bindings: phy: describe the Qualcomm SGMII PHY
phy: qualcomm: fix indentation in Makefile
phy: usb: suppress OC condition for 7439b2
phy: usb: Turn off phy when port is in suspend
phy: tegra: xusb: Clear the driver reference in usb-phy dev
dt-bindings: phy: mxs-usb-phy: add imx8ulp and imx8qm compatible
dt-bindings: phy: mxs-usb-phy: convert to DT schema format
dt-bindings: phy: qcom,qmp-usb: fix bindings error
dt-bindings: phy: qcom,qmp-ufs: fix the sc8180x regs
dt-bindings: phy: qcom,qmp-pcie: fix the sc8180x regs
phy: mediatek: tphy: add debugfs files
phy: core: add debugfs files
phy: fsl-imx8mp-usb: add support for phy tuning
...
-----BEGIN PGP SIGNATURE-----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=YwIy
-----END PGP SIGNATURE-----
Merge tag 'media/v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Lots of improvement at atomisp driver, which is starting to look in
good shape
- Mediatek vcodec driver has gained support for av1 and hevc stateless
codecs
- New sensor driver: ov01a10
- verisilicon driver has gained AV1 entropy helpers
- tegra-video has gained support for Tegra20 parallel input
- dvb core has gained an extra property to better support DVB-S2X
- as usual, lots of cleanups, fixes and improvements on media drivers
* tag 'media/v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (253 commits)
media: wl128x: fix a clang warning
media: dvb: mb86a20s: get rid of a clang-15 warning
media: cec: i2c: ch7322: also select REGMAP
media: add HAS_IOPORT dependencies
media: tc358746: select CONFIG_GENERIC_PHY
media: mediatek: vcodec: Add dbgfs help function
media: mediatek: vcodec: Add encode to support dbgfs
media: mediatek: vcodec: Change dbgfs interface to support encode
media: mediatek: vcodec: Get each instance format type
media: mediatek: vcodec: Get each context resolution information
media: mediatek: vcodec: Add a debugfs file to get different useful information
media: mediatek: vcodec: Add debug params to control different log level
media: mediatek: vcodec: Add debugfs interface to get debug information
media: mediatek: vcodec: support stateless AV1 decoder
media: verisilicon: Conditionally ignore native formats
media: verisilicon: Enable AV1 decoder on rk3588
media: verisilicon: Add film grain feature to AV1 driver
media: verisilicon: Add Rockchip AV1 decoder
media: verisilicon: Add AV1 entropy helpers
media: verisilicon: Compute motion vectors size for AV1 frames
...
SoC support. Instead there's a treewide patch series from Maxime that makes
clk_ops::determine_rate mandatory for muxes. Beyond that core framework change
we have the usual pile of clk driver updates such as migrating i2c drivers to
use .probe() again or YAMLfication of clk DT bindings so we can validate DTBs.
Overall the SoCs that got the most updates this time around in terms of
diffstat are the Amlogic and Mediatek drivers because they added new SoC
support or fixed up various drivers to have proper data.
In general things look kinda quiet. I suspect the core framework change may
still shake out some problems after the merge window, mostly because not
everyone tests linux-next where that series has been for some number of weeks.
I saw that there's at least one pending fix for Tegra that needs to be wrapped
up into a proper patch. I'll try to catch those bits before the window closes
so that -rc1 is bootable. More details below.
Core:
- Make clk_ops::determine_rate mandatory for muxes
New Drivers:
- Add amlogic a1 SoC family PLL and peripheral clock controller support
Updates:
- Handle allocation failures from kasprintf() and friends
- Migrate platform clk drivers to .remove_new()
- Migrate i2c clk drivers to .probe() instead of .probe_new()
- Remove CLK_SET_PARENT from all Mediatek MSDC core clocks
- Add infra_ao reset support for Mediatek MT8188 SoCs
- Align driver_data to i2c_device_id tables in some i2c clk drivers
- Use device_get_match_data() in vc5 clk driver
- New Kconfig symbol name (SOC_MICROCHIP_POLARFIRE) for Microchip FPGA clock
drivers
- Use of_property_read_bool() to read "microchip,pic32mzda-sosc" boolean DT
property in clk-pic32mzda
- Convert AT91 clock dt-bindings to YAML
- Remove CLK_SET_RATE_PARENT flag from LDB clocks on i.MX6SX
- Keep i.MX UART clocks enabled during kernel boot if earlycon is set
- Drop imx_unregister_clocks() as there are no users anymore
- Switch to _safe iterator on imx_clk_scu_unregister() to avoid use after free
- Add determine_rate op to the imx8m composite clock
- Use device managed API for iomap and kzalloc for i.MXRT1050, i.MX8MN,
i.MX8MP and i.MX93 clock controller drivers
- Add missing interrupt DT property for the i.MX8M clock controller
- Re-add support for Exynos4212 clock controller because we are
re-introducing the SoC in the mainline
- Add CONFIG_OF dependency to Samsung clk Kconfig symbols to solve some
objtool warnings
- Preselect PLL MIPI as TCON0 parent for Allwinner A64 SoC
- Convert the Renesas clock drivers to readl_poll_timeout_atomic()
- Add PWM clock on Renesas R-Car V3U
- Fix PLL5 on Renesas RZ/G2L and RZ/V2L
-----BEGIN PGP SIGNATURE-----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=6M8D
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This batch of clk driver updates contains almost no new SoC support.
Instead there's a treewide patch series from Maxime that makes
clk_ops::determine_rate mandatory for muxes.
Beyond that core framework change we have the usual pile of clk driver
updates such as migrating i2c drivers to use .probe() again or
YAMLfication of clk DT bindings so we can validate DTBs.
Overall the SoCs that got the most updates this time around in terms
of diffstat are the Amlogic and Mediatek drivers because they added
new SoC support or fixed up various drivers to have proper data.
In general things look kinda quiet. I suspect the core framework
change may still shake out some problems after the merge window,
mostly because not everyone tests linux-next where that series has
been for some number of weeks. I saw that there's at least one pending
fix for Tegra that needs to be wrapped up into a proper patch. I'll
try to catch those bits before the window closes so that -rc1 is
bootable. More details below.
Core:
- Make clk_ops::determine_rate mandatory for muxes
New Drivers:
- Add amlogic a1 SoC family PLL and peripheral clock controller support
Updates:
- Handle allocation failures from kasprintf() and friends
- Migrate platform clk drivers to .remove_new()
- Migrate i2c clk drivers to .probe() instead of .probe_new()
- Remove CLK_SET_PARENT from all Mediatek MSDC core clocks
- Add infra_ao reset support for Mediatek MT8188 SoCs
- Align driver_data to i2c_device_id tables in some i2c clk drivers
- Use device_get_match_data() in vc5 clk driver
- New Kconfig symbol name (SOC_MICROCHIP_POLARFIRE) for Microchip
FPGA clock drivers
- Use of_property_read_bool() to read "microchip,pic32mzda-sosc"
boolean DT property in clk-pic32mzda
- Convert AT91 clock dt-bindings to YAML
- Remove CLK_SET_RATE_PARENT flag from LDB clocks on i.MX6SX
- Keep i.MX UART clocks enabled during kernel boot if earlycon is set
- Drop imx_unregister_clocks() as there are no users anymore
- Switch to _safe iterator on imx_clk_scu_unregister() to avoid use
after free
- Add determine_rate op to the imx8m composite clock
- Use device managed API for iomap and kzalloc for i.MXRT1050,
i.MX8MN, i.MX8MP and i.MX93 clock controller drivers
- Add missing interrupt DT property for the i.MX8M clock controller
- Re-add support for Exynos4212 clock controller because we are
re-introducing the SoC in the mainline
- Add CONFIG_OF dependency to Samsung clk Kconfig symbols to solve
some objtool warnings
- Preselect PLL MIPI as TCON0 parent for Allwinner A64 SoC
- Convert the Renesas clock drivers to readl_poll_timeout_atomic()
- Add PWM clock on Renesas R-Car V3U
- Fix PLL5 on Renesas RZ/G2L and RZ/V2L"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (149 commits)
clk: fix typo in clk_hw_register_fixed_rate_parent_data() macro
clk: Fix memory leak in devm_clk_notifier_register()
clk: mvebu: Iterate over possible CPUs instead of DT CPU nodes
clk: mvebu: Use of_get_cpu_hwid() to read CPU ID
MAINTAINERS: Add Marvell mvebu clock drivers
clk: clocking-wizard: check return value of devm_kasprintf()
clk: ti: clkctrl: check return value of kasprintf()
clk: keystone: sci-clk: check return value of kasprintf()
clk: si5341: free unused memory on probe failure
clk: si5341: check return value of {devm_}kasprintf()
clk: si5341: return error if one synth clock registration fails
clk: cdce925: check return value of kasprintf()
clk: vc5: check memory returned by kasprintf()
clk: mediatek: clk-mt8173-apmixedsys: Fix iomap not released issue
clk: mediatek: clk-mt8173-apmixedsys: Fix return value for of_iomap() error
clk: mediatek: clk-mtk: Grab iomem pointer for divider clocks
clk: keystone: syscon-clk: Add support for audio refclk
dt-bindings: clock: Add binding documentation for TI Audio REFCLK
dt-bindings: clock: ehrpwm: Remove unneeded syscon compatible
clk: keystone: syscon-clk: Allow the clock node to not be of type syscon
...
The tc358746 driver selects CONFIG_GENERIC_PHY_MIPI_DPHY and links to
that, but this fails when CONFIG_GENERIC_PHY is disabled, because Kbuild
then never enters the drivers/phy directory for building object files:
ERROR: modpost: "phy_mipi_dphy_get_default_config_for_hsclk" [drivers/media/i2c/tc358746.ko] undefined!
Add an explicit 'select GENERIC_PHY' here to ensure that the directory
is entered, and add another dependency on that symbol so make it
more obvious what is going on if another driver has the same problem,
as this will produce a Kconfig warning.
Link: https://lore.kernel.org/linux-media/20230623152318.2276816-1-arnd@kernel.org
Fixes: 80a21da360 ("media: tc358746: add Toshiba TC358746 Parallel to CSI-2 bridge driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The SM8550 PHY also uses a different offset for the CMN_STATUS reg,
use the right one for the v6 Display Port configuration.
Fixes: 49742e9eda ("phy: qcom-qmp-combo: Add support for SM8550")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230601-topic-sm8550-upstream-dp-phy-init-fix-v1-1-4e9da9f97991@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Implement support for the SGMII/SerDes PHY present on various Qualcomm
platforms.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230619091336.194914-4-brgl@bgdev.pl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We hit a false positive OC for 7439b2 in DRD/device mode for the
second port. So disable the OC check for this use case. Add capability
to suppress OC condition for specific ports.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/1686859578-45242-3-git-send-email-justin.chen@broadcom.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The COMMONONN bit turns off the PHY when the host controller puts it
into suspend state. This can happen during the following...
- Nothing is connected to the port
- The host controller goes into low power mode whatever due to auto
suspend or system suspend.
With COMMONONN we also must unset U2_FREECLK_EXISTS since the UTMI
clock is fed by the PHY.
With these changes we see a power savings of ~12mW when port is in
suspend.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Link: https://lore.kernel.org/r/1686859578-45242-2-git-send-email-justin.chen@broadcom.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For the dual-role port, it will assign the phy dev to usb-phy dev and
use the port dev driver as the dev driver of usb-phy.
When we try to destroy the port dev, it will destroy its dev driver
as well. But we did not remove the reference from usb-phy dev. This
might cause the use-after-free issue in KASAN.
Fixes: e8f7d2f409 ("phy: tegra: xusb: Add usb-phy support")
Cc: stable@vger.kernel.org
Signed-off-by: EJ Hsu <ejh@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230609062932.3276509-1-haotienh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The TI J721e Wiz clock implements a mux with a set_parent
hook, but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidate to
trigger that parent change is a call to clk_set_rate(), with
determine_rate() figuring out which parent is the best suited for a
given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the flag
CLK_SET_RATE_NO_REPARENT, together with setting our determine_rate hook
to __clk_mux_determine_rate(). Indeed, if no determine_rate
implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Since the CLK_SET_RATE_NO_REPARENT flag was already set though, it seems
unlikely.
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-44-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The TI AM654 SerDes clock implements a mux with a set_parent
hook, but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidate to
trigger that parent change is a call to clk_set_rate(), with
determine_rate() figuring out which parent is the best suited for a
given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the flag
CLK_SET_RATE_NO_REPARENT, together with setting our determine_rate hook
to __clk_mux_determine_rate(). Indeed, if no determine_rate
implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Since the CLK_SET_RATE_NO_REPARENT flag was already set though, it seems
unlikely.
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-43-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Cadence Torrent refclk clock implements a mux with a set_parent
hook, but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidate to
trigger that parent change is a call to clk_set_rate(), with
determine_rate() figuring out which parent is the best suited for a
given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the flag
CLK_SET_RATE_NO_REPARENT, together with setting our determine_rate hook
to __clk_mux_determine_rate(). Indeed, if no determine_rate
implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Since the CLK_SET_RATE_NO_REPARENT flag was already set though, it seems
unlikely.
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-42-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Cadence Sierra PLL clock implements a mux with a set_parent hook,
but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidate to
trigger that parent change is a call to clk_set_rate(), with
determine_rate() figuring out which parent is the best suited for a
given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the flag
CLK_SET_RATE_NO_REPARENT, together with setting our determine_rate hook
to __clk_mux_determine_rate(). Indeed, if no determine_rate
implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Since the CLK_SET_RATE_NO_REPARENT flag was already set though, it seems
unlikely.
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-41-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
These debugfs files are mainly used to make eye diagram test easier,
especially helpful to do HQA test for a new IC without efuse enabled.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230513092218.21139-2-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a debugfs root for phy class, and create a debugfs directory under
the root when create phy, then phy drivers can add debugfs files.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230513092218.21139-1-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add USB PHY parameter tuning for USB certifications.
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
[j.zink: ported to v6.3-rc1 from NXP downstream repo + cleanups]
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230516-lustige-usb-phy-dinge-v2-2-3383a0de34ac@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The QMP combo PHY sits in an of_graph connected between the DisplayPort
controller and a USB Type-C connector (or possibly a redriver).
The TCPM needs to be able to convey the HPD signal to the DisplayPort
controller, but no directly link is provided by DeviceTree so the signal
needs to "pass through" the QMP combo phy.
Handle this by introducing a drm_bridge which upon initialization finds
the next bridge (i.e. the usb-c-connector) and chain this together. This
way HPD changes in the connector will propagate to the DisplayPort
driver.
The connector bridge is resolved lazily, as the TCPM is expected to be
able to resolve the typec mux and switch at probe time, so the QMP combo
phy will probe before the TCPM.
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-7-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The data lanes of the QMP PHY is swapped in order to handle changing
orientation of the USB Type-C cable. Register a typec_switch device to
allow a TCPM to configure the orientation.
The newly introduced orientation variable is adjusted based on the
request, and the initialized components are brought down and up again.
To keep track of what parts needs to be cycled new variables to keep
track of the individual init_count is introduced.
Both the USB and the DisplayPort altmode signals are properly switched.
For DisplayPort the controller will after the TCPM having established
orientation power on the PHY, so this is not done implicitly, but for
USB the PHY typically is kept initialized across the switch, and must
therefore then be reinitialized.
This is based on initial work by Wesley Cheng.
Link: https://lore.kernel.org/r/20201009082843.28503-3-wcheng@codeaurora.org/
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-6-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In multiple places throughout the driver code has been written in
prepration for handling of orientation switching.
Introduce a typec_orientation in qmp_combo and fill out the various
"placeholders" with the associated logic. By initializing the
orientation to "normal" this change has no functional impact, but
reduces the size of the upcoming introduction of dynamic orientation
switching.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-5-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The phy core ensures mutual exclusion across the ops for a given phy,
but the upcoming introduction of USB Type-C orientation switching might
race with the DisplayPort phy operations. So extend the mutual exclusion
to cover the remaining ops as well, to avoid concurrent reconfiguration
of the hardware.
Reported-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-4-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With the upcoming introduction of USB Type-C orientation switching the
region of mutual exclusion needs to be extended to cover both the common
init/exit as well as the individual functions.
So move the phy_mutex one step up the stack.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-3-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add cdns,usb2-disconnect-threshold-microvolt property to address fake USB
disconnection issue during enumeration or suspend state for difference
platform.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-6-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For NXP platform design, the PHY can't know VBUS well, it causes the FSM
in controller seeing the disconnection at L1 use case. With .set_mode API
introduced, the controller driver could force PHY seeing B Session VALID
when it is at the device mode (VBUS is there), and keep FSM working well.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-5-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Very limited parts may fail to work on full speed mode (both host and
device modes) for USB3 port due to higher threshold in full speed receiver
of USB2.0 PHY.
One example failure symptom is, the enumeration is failed when connecting
full speed USB mouse to USB3 port, especially under high temperature.
The workaround is to configure threshold voltage value of single ended
receiver by setting USB2.0 PHY register AFE_RX_REG5[2:0] to 3'b101.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-4-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For USB2 L1 use cases, some hosts may start transferring less than 20us
after End of Resume, it causes the host seeing corrupt packet from the
device side. The reason is the delay time between PHY powers up and
txvalid is 20us. To fix it, we change the delay value as 0us.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-3-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is an offset for USB2PHY in SALVO phy, add offset parameter for read
and write API to cover both USB2 and USB3 PHY control.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-2-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the new qcm2290 / sm6115 binding.
The USB QMP phy on these devices supports 2 lanes. Note that the
binding now does not describe every register subregion and instead
the driver holds the corresponding offsets.
While at it also include support for PCS_MISC region which was left
out earlier.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20230516150511.2346357-3-bhupesh.sharma@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TI's J784S4 SoC supports USXGMII mode with the CPSW9G instance's MAC
ports 1 and 2. Add USXGMII mode to the extra_modes member of J784S4's
SoC data.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230331062521.529005-3-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Each of the CPSW9G ports in TI's J784S4 SoC support modes such as QSGMII.
Add a new compatible for it and allow the usage of "ti,qsgmii-main-ports"
property for J784S4.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230331062521.529005-2-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TI's J721E SoC supports SGMII mode with the CPSW9G instance of the CPSW
Ethernet Switch. Thus, enable it by adding SGMII mode to the list of the
corresponding extra_modes member.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230309063514.398705-4-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TI's J7200 SoC supports SGMII mode with the CPSW5G instance of the CPSW
Ethernet Switch. Thus, enable it by adding SGMII mode to the list of the
corresponding extra_modes member.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230309063514.398705-3-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support to configure the CPSW MAC's PHY in SGMII mode if the SoC
supports it. The extra_modes member of the phy_gmii_sel_soc_data struct
corresponding to the SoC is used to determine whether or not the SoC
supports SGMII mode.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230309063514.398705-2-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Convert platform_get_resource(),devm_ioremap_resource() to a single
call to devm_platform_ioremap_resource(), as this is exactly what this
function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230428052758.38636-1-yang.lee@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update kerneldoc of struct qcom_snps_hsphy to fix:
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c:135: warning: Function parameter or member 'update_seq_cfg' not described in 'qcom_snps_hsphy'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230507144818.193039-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
gcc on aarch64 reports
drivers/phy/mediatek/phy-mtk-hdmi-mt8195.c: In function ‘mtk_hdmi_pll_set_rate’:
drivers/phy/mediatek/phy-mtk-hdmi-mt8195.c:240:52: error: ‘-mgeneral-regs-only’
is incompatible with the use of floating-point types
240 | else if (tmds_clk >= 54 * MEGA && tmds_clk < 148.35 * MEGA)
Floating point should not be used, so rework the floating point comparisons
to fixed point.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230502145005.2927101-1-trix@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Support for inno-usb2-phy on Hi3798MV100 was added into existing driver,
while Hi3798MV100 is a A9 ARM32-only SoC.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://lore.kernel.org/r/20230509060449.1151113-3-mmyangfl@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Adopt existing phy-hisi-inno-usb2 driver to Hi3798MV100, with a slightly
different TEST register convention.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://lore.kernel.org/r/20230509060449.1151113-2-mmyangfl@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Support for the Exynos4212 SoC was originally dropped as there were
no boards using it. We will be adding a device that uses it, so add
it back.
This reverts commit fee7e1d50c.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230501195525.6268-9-aweber.kernel@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Updated USB QMP PHY Init sequence based on HPG for IPQ9574.
Reused clock and reset list from existing targets.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/4f15c21f28e2a1332fbdb04d60641cbbf05c6f15.1683630932.git.quic_varada@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a check for skip_cmu_cfg when configuring the serdes lane. All
individual serdeses are reset upon first configuration. Resetting the
serdes involves reconfiguring it with preset values. The serdesmode is
required to determine the clock-providing CMU, therefore make sure the
serdes is not reconfigured if the serdesmode is not set.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://lore.kernel.org/r/20230417180335.2787494-8-daniel.machon@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Power on the CMU instance, that provides the clock for the serdes, given the
specified serdes mode and index. The CMU instance is looked up, using a
preset map of serdes mode and index to CMU index.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://lore.kernel.org/r/20230417180335.2787494-6-daniel.machon@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All CMUs are powered up initially. This uses needless power. This patch
makes sure all CMUs are powered down by default. This involves
configuring a number reference clock and power-down registers of the
CMU.
Individual CMUs are later powered up, when the serdes lanes are
configured.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://lore.kernel.org/r/20230417180335.2787494-5-daniel.machon@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All the serdes lanes of the sparx5 will transition between normal mode
and quiet mode, depending on activity. Make sure that the quiet mode is
configured optimally for all lanes initially. Although not much, this
will save a small amount of power.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://lore.kernel.org/r/20230417180335.2787494-3-daniel.machon@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add multilink DP configuration support for 100MHz reference clock rate.
This is the only clock rate supported currently for multilink PHY
configurations. Also, add PCIe + DP multiprotocol multilink register
configuration sequences for 100MHz refclk with no SSC.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20230418173157.25607-4-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch prepares driver for multilink DP support as well as for
multiprotocol PHY configurations involving DP as one of the required
protocols. This needs changes in functions configuring default single
link DP with master lane 0 to support non-zero master lane values and
associated PLL configurations.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20230418173157.25607-3-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Torrent PHY PLL0 or PLL1 is used for DP depending on the single link or
multilink protocol configuration for which PHY is configured. In multilink
configurations with other protocols, either PLL0 or PLL1 will be used
for DP. For single link DP, both PLLs need to be configured at POR.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20230418173157.25607-2-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SA8775P platform has 5nm USB3 UNI phy attached to the USB0 and USB1
controllers.
Add QMP PHY config, pcs entries and support for the new compatible for
SA8775P platform.
Signed-off-by: Shazad Hussain <quic_shazhuss@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230428130824.23803-5-quic_shazhuss@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
