Fix the cam0 sysreg property name (samsung,cam0-sysreg), which has been
erroneously declared as samsung,cam-sysreg. This follows the same name
used in Exynos5433 PHY.
Fixes: 543f5e3142 ("phy: exynos-mipi-video: introduce support for exynos7870")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Link: https://lore.kernel.org/r/20250710-exynos7870-mipi-phy-fix-v2-1-5cf50d69c9d7@disroot.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for Exynos7870 in the existing MIPI CSIS/DSIM driver. The
SoC has one DSIM phy and three CSIS phys.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250612-exynos7870-mipi-phy-v1-2-3fff0b62d9d3@disroot.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Exynos990 usbdrd PHY is a combo PHY which supports USB SS, HS and
DisplayPort outputs. This commit adds support only for UTMI+ (USB HS).
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Igor Belwon <igor.belwon@mentallysanemainliners.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250515-usb-resends-may-15-v3-2-ad33a85b6cee@mentallysanemainliners.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the Exynos USB 3.2 DRD 4nm controller. It's used in
recent 4nm SoCs like Exynos2200 and Exynos2400.
This device consists of 3 underlying and independent phys: SEC link
control phy, Synopsys eUSB 2.0 and Synopsys USBDP/SS combophy. Unlike
older device designs, where the internal phy blocks were all IP of
Samsung, Synopsys phys are present. This means that the link controller
is now mapped differently to account for missing bits and registers.
The Synopsys phys also have separate register bases.
As there are non-SEC PHYs present now, it doesn't make much sense to
implement them in this driver. They are expected to be configured
by external drivers, so pass phandles to them. USBDRD3.2 link controller
set up is still required beforehand.
This commit adds the necessary changes for USB HS to work. USB SS and
DisplayPort are out of scope in this commit and will be introduced
in the future.
Signed-off-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Link: https://lore.kernel.org/r/20250504144527.1723980-11-ivo.ivanov.ivanov1@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 9b6662a0f7 ("phy: exynos5-usbdrd: use GENMASK and FIELD_PREP
for Exynos5 PHY registers") added FIELD_PREP_CONST() in many cases
where FIELD_PREP() would have been more appropriate. It also switched
existing uses of FIELD_PREP() to FIELD_PREP_CONST().
FIELD_PREP() is the preferred macro to use whenever possible while
FIELD_PREP_CONST() is meant to be used in constant initialisers.
Switch (back) to FIELD_PREP().
Fixes: 7e6c2ffe6c ("phy: exynos5-usbdrd: convert some FIELD_PREP_CONST() to FIELD_PREP()")
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250429-exynos5-phy-field-prep-v1-2-39eb279a3e0e@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The code here is trying to set the FLADJ field to 0x20, so it should
clear any previous value in that field before or'ing-in the new value.
Fixes: 588d5d20ca ("phy: exynos5-usbdrd: add exynos7870 USBDRD support")
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250429-exynos5-phy-field-prep-v1-1-39eb279a3e0e@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Implement support for Exynos7870 USB DRD on top of the existing
exynos5-usbdrd driver.
Exynos7870 has a single USB 2.0 DRD PHY controller and no 3.0 PHYs. Thus,
it only supports the UTMI interface.
Moreover, the PMU register offset for enabling the PHY controller is
different for SoCs such as Exynos7870, where BIT(0) is for the 3.0 PHY and
BIT(1) is for the 2.0 PHY. The phy_isol function for Exynos7870 uses the
appropriate register offsets.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Link: https://lore.kernel.org/r/20250410-exynos7870-usbphy-v2-3-2eb005987455@disroot.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Most Exynos850 and Exynos9 (GS101) DRD PHY registers use GENMASK for masks
and FIELD_PREP for writing values to registers.
Rewrite the register definitions which don't follow this approach to follow
it as much as possible. This patch doesn't introduce any fixes or
functional changes, it's merely an attempt to introduce some uniformity and
consistency in the driver code.
The CRPORT SuperSpeed control registers have been exempted from this
change. Since the writing of register values do not require any masking
operations, implementing it would unnecessarily complicate things.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Link: https://lore.kernel.org/r/20250410-exynos7870-usbphy-v2-1-2eb005987455@disroot.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Older Exynos designs, like Exynos5422, do not have USB Type-C and the
USB DRD PHY does not really need CONFIG_TYPEC for these devices at all.
Incorrectly added optional dependency on CONFIG_TYPEC caused this driver
to be missing for exynos_defconfig and as result Exynos5422-based boards
like Hardkernel Odroid HC1 failed to probe USB.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Closes: https://krzk.eu/#/builders/21/builds/6139
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/all/3c0b77e6-357d-453e-8b63-4757c3231bde@samsung.com/
Fixes: 09dc674295 ("phy: exynos5-usbdrd: subscribe to orientation notifier if required")
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250227070518.5468-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We currently don't gate the power to the SS phy in phy_exit().
Shuffle the code slightly to ensure the power is gated to the SS phy as
well.
Fixes: 32267c29bc ("phy: exynos5-usbdrd: support Exynos USBDRD 3.1 combo phy (HS & SS)")
CC: stable@vger.kernel.org # 6.11+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20241205-gs101-usb-phy-fix-v4-1-0278809fb810@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To make USB runtime suspend work when a UDC has been bound, the phy
needs to inform the USBDRD controller (DWC3) that Vbus and bvalid are
gone, so that it can in turn raise the respective gadget interrupt with
event == DWC3_DEVICE_EVENT_DISCONNECT, which will cause the USB stack
to clean up, allowing DWC3 to enter runtime suspend.
On e850 and gs101 this isn't working, as the respective signals are not
directly connected, and instead this driver uses override bits in the
PHY IP to set those signals. It currently forcefully sets them to 'on',
so the above mentioned interrupt will not be raised, preventing runtime
suspend.
To detect that state, update this driver to act on the TCPC's
orientation signal - when orientation == NONE, Vbus is gone and we can
clear the respective bits. Similarly, for other orientation values we
re-enable them.
This makes runtime suspend work on platforms with a TCPC (like Pixel6),
while keeping compatibility with platforms without (e850-96).
With runtime suspend working, USB-C cable orientation detection now
also fully works on such platforms, and the link comes up as Superspeed
as expected irrespective of the cable orientation and whether UDC /
gadget are configured and active.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-7-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
gs101's SS phy needs to be configured differently based on the
connector orientation, as the SS link can only be established if the
mux is configured correctly.
The code to handle programming of the mux is in place already, this commit
now adds the missing pieces to subscribe to the Type-C orientation
switch event.
Note that for this all to work we rely on the USB controller
re-initialising us. It should invoke our .exit() upon cable unplug, and
during cable plug we'll receive the orientation event after which we
expect our .init() to be called.
Above reinitialisation happens if the DWC3 controller can enter runtime
suspend automatically. For the DWC3 driver, this is an opt-in:
echo auto > /sys/devices/.../11110000.usb/power/control
Once done, things work as long as the UDC is not bound as otherwise it
stays busy because it doesn't cancel / stop outstanding TRBs. For now
we have to manually unbind the UDC in that case:
echo "" > sys/kernel/config/usb_gadget/.../UDC
Note that if the orientation-switch property is missing from the DT,
the code will behave as before this commit (meaning for gs101 it will
work in SS mode in one orientation only). Other platforms are not
affected either way.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-6-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
USB SS lanes need to be configured based on the connector orientation -
at most two lanes will be in use for USB (and the remaining two for
alternate modes like DP).
For the USB link to come up in SS, the lane configuration registers
have to be programmed accordingly.
While we still need a way to be notified of the actual connector
orientation and then reprogram the registers accordingly (at the moment
the configuration happens just once during phy_init() and never again),
we can prepare the code doing the configuration to take the orientation
into account.
Do so.
Note: the mutex is needed to synchronize this with the upcoming
connector orientation callback.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-5-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This code's intention is to configure lane0 and lane2 tunings, but for
lane2 there is a typo and it ends up tuning something else.
Fix the typo, as it doesn't appear to make sense to apply different
tunings for lane0 vs lane2.
The same typo appears to exist in the bootloader, hence we restore the
original value in the typo'd registers as well. This can be removed
once / if the bootloader is updated.
Note that this is incorrect in the downstream driver as well - the
values had been copied from there.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-4-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In exynos5_usbdrd_{pipe3,utmi}_set_refclk(), the masks
PHYCLKRST_MPLL_MULTIPLIER_MASK and PHYCLKRST_SSC_REFCLKSEL_MASK are not
inverted when applied to the register values. Fix it.
Cc: stable@vger.kernel.org
Fixes: 59025887fb ("phy: Add new Exynos5 USB 3.0 PHY driver")
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20250209-exynos5-usbdrd-masks-v1-1-4f7f83f323d7@disroot.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now exynos-pmu can register its custom regmap for gs101 via
of_syscon_register_regmap() we can switch back to the standard
syscon_regmap_lookup_by_phandle() api for obtaining the regmap.
Additionally add a Kconfig dependency for MFD_SYSCON.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20241029192107.2344279-1-peter.griffin@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- New Support
- Rcar usb2 support for RZ/G3S SoC
- Nuvoton MA35 SoC USB 2.0 PHY driver
- Removal
- obsolete qcom,usb-8x16-phy bindings
- Updates
- 4 lane PCIe support for Qualcomm X1E80100
- Constify structure in subsystem update
- Subsystem simplification with scoped for each OF child loop update
- Yaml conversion for Qualcomm sata phy, Hiilicon hi3798cv200-combphy
bindings
-----BEGIN PGP SIGNATURE-----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=XJmz
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New hw support:
- Rcar usb2 support for RZ/G3S SoC
- Nuvoton MA35 SoC USB 2.0 PHY driver
Removed:
- obsolete qcom,usb-8x16-phy bindings
Updates:
- 4 lane PCIe support for Qualcomm X1E80100
- Constify structure in subsystem update
- Subsystem simplification with scoped for each OF child loop update
- Yaml conversion for Qualcomm sata phy, Hiilicon hi3798cv200-combphy
bindings"
* tag 'phy-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (40 commits)
phy: renesas: rcar-gen3-usb2: Add support for the RZ/G3S SoC
dt-bindings: phy: renesas,usb2-phy: Document RZ/G3S phy bindings
phy: renesas: rcar-gen3-usb2: Add support to initialize the bus
phy: ti: j721e-wiz: Simplify with scoped for each OF child loop
phy: ti: j721e-wiz: Drop OF node reference earlier for simpler code
phy: ti: gmii-sel: Simplify with dev_err_probe()
phy: ti: am654-serdes: Use scoped device node handling to simplify error paths
phy: qcom: qmp-pcie-msm8996: Simplify with scoped for each OF child loop
phy: mediatek: xsphy: Simplify with scoped for each OF child loop
phy: mediatek: tphy: Simplify with scoped for each OF child loop
phy: hisilicon: usb2: Simplify with scoped for each OF child loop
phy: cadence: sierra: Simplify with scoped for each OF child loop
phy: broadcom: brcm-sata: Simplify with scoped for each OF child loop
phy: broadcom: bcm-cygnus-pcie: Simplify with scoped for each OF child loop
phy: nuvoton: add new driver for the Nuvoton MA35 SoC USB 2.0 PHY
dt-bindings: phy: nuvoton,ma35-usb2-phy: add new bindings
phy: qcom: qmp-pcie: Configure all tables on port B PHY
phy: airoha: adjust initialization delay in airoha_pcie_phy_init()
dt-bindings: phy: socionext,uniphier: add top-level constraints
phy: qcom: qmp-pcie: Add Gen4 4-lanes mode for X1E80100
...
Use of FIELD_PREP_CONST() was a thinko - it's meant to be used for
(constant) initialisers, not constant values.
Use FIELD_PREP() where possible. It has better error checking and is
therefore the preferred macro to use in those cases.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240710-phy-field-prep-v1-1-2fa3f7dc4fc7@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the Exynos USB 3.1 DRD combo phy, as found in Exynos 9
SoCs like Google GS101. It supports USB SS, HS and DisplayPort.
In terms of UTMI+, this is very similar to the existing Exynos850
support in this driver. The difference is that this combo phy supports
both UTMI+ (HS) and PIPE3 (SS). It also supports DP alt mode.
The number of ports for UTMI+ and PIPE3 can be determined using the
LINKPORT register (which also exists on Exynos E850).
For SuperSpeed (SS) a new SS phy is in use and its PIPE3 interface is
new compared to Exynos E850, and also very different from the existing
support for older Exynos SoCs in this driver.
The SS phy needs a bit more configuration work and register tuning for
signal quality to work reliably, presumably due to the higher
frequency, e.g. to account for different board layouts. Additionally,
power needs to be enabled before writing to the SS phy registers.
This commit adds the necessary changes for USB HS and SS to work.
DisplayPort is out of scope in this commit.
Notes:
* For the register tuning, exynos5_usbdrd_apply_phy_tunes() has been
added with the appropriate data structures to support tuning at
various stages during initialisation. Since these are hardware
specific, the platform data is supposed to be populated accordingly.
The implementation is loosely modelled after the Samsung UFS PHY
driver.
There is one tuning state for UTMI+, PTS_UTMI_POSTINIT, to execute
after init and generally intended for HS signal tuning, as done in
this commit.
PTS_PIPE3_PREINIT PTS_PIPE3_INIT PTS_PIPE3_POSTINIT
PTS_PIPE3_POSTLOCK are tuning states for PIPE3. In the downstream
driver, preinit differs by Exynos SoC, and postinit and postlock
are different per board. The latter haven't been implemented for
gs101 here, because downstream doesn't use them on gs101 either.
* Signal lock acquisition for SS depends on the orientation of the
USB-C plug. Since there currently is no infrastructure to chain
connector events to both the USB DWC3 driver and this phy driver, a
work-around has been added in
exynos5_usbdrd_usbdp_g2_v4_pma_check_cdr_lock() to check both
registers if it failed in one of the orientations.
* Equally, we can only establish SS speed in one of the connector
orientations due to programming differences when selecting the lane
mux in exynos5_usbdrd_usbdp_g2_v4_pma_lane_mux_sel(), which really
needs to be dynamic, based on the orientation of the connector.
* As is, we can establish a HS link using any cable, and an SS link in
one orientation of the plug, falling back to HS if the orientation is
reversed to the expectation.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-6-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using the regulator_bulk APIs, the handling of power supplies becomes
much simpler. There is no need anymore to check if regulators have been
acquired or not, the bulk APIs will do all the work for us. We can also
drop the various handles to the individual power supplies in the driver
runtime data and instead simply treat them all as one thing. Error
cleanup also becomes much simpler.
Converting to the regulator_bulk APIs also makes it easier to add
support for those SoCs that have additional power supplies for the PHY.
Google Tensor gs101 is one example of such a SoC. Otherwise we'd have
to add all additional supplies individually via individual calls to
regulator_get() and enable/disable handle them all individually,
including complicated error handling. That doesn't scale and clutters
the code.
Just update the code to use the regulator_bulk APIs.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-5-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for support for additional platforms, convert the phy
register access clock to using the clk_bulk interfaces.
Newer SoCs like Google Tensor gs101 require additional clocks for
access to additional (different) register areas (PHY, PMA, PCS), and
converting to clk_bulk simplifies addition of those extra clocks.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-4-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using the clk_bulk APIs, the clock handling for the core clocks becomes
much simpler. No need to check any flags whether or not certain clocks
exist or not. Further, we can drop the various handles to the
individual clocks in the driver data and instead simply treat them all
as one thing.
So far, this driver assumes that all platforms have a clock "ref". It
also assumes that the clocks "phy_pipe", "phy_utmi", and "itp" exist if
the platform data "has_common_clk_gate" is set to true. It then goes
and individually tries to acquire and enable and disable all the
individual clocks one by one. Rather than relying on these implicit
clocks and open-coding the clock handling, we can just explicitly spell
out the clock names in the different device data and use that
information to populate clk_bulk_data, allowing us to use the clk_bulk
APIs for managing the clocks.
As a side-effect, this change highlighted the fact that
exynos5_usbdrd_phy_power_on() forgot to check the result of the clock
enable calls. Using the clk_bulk APIs, the compiler now warns when
return values are not checked - therefore add the necessary check
instead of silently ignoring failures and continuing as if all is OK
when it isn't.
For consistency, also change a related dev_err() to dev_err_probe() in
exynos5_usbdrd_phy_clk_handle() to get consistent error message
formatting.
Finally, exynos5_usbdrd_phy_clk_handle() prints an error message in all
cases as necessary (except for -ENOMEM). There is no need to print
another message in its caller (the probe() function), and printing
errors during OOM conditions is usually discouraged. Drop the
duplicated message in exynos5_usbdrd_phy_probe().
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-3-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some versions of this IP have been integrated using separate PMU power
control registers for the HS and SS parts. One example is the Google
Tensor gs101 SoC.
Such SoCs can now set pmu_offset_usbdrd0_phy_ss in their
exynos5_usbdrd_phy_drvdata for the SS phy to the appropriate value.
The existing 'usbdrdphy' alias can not be used in this case because
that is meant for determining the correct PMU offset if multiple
distinct PHYs exist in the system (as opposed to one PHY with multiple
isolators).
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-2-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While commit 255ec3879d ("phy: exynos5-usbdrd: Add 26MHz ref clk
support") correctly states that CLKRSTCTRL[7:5] doesn't need to be set
on modern Exynos platforms, SSPPLLCTL[2:0] should be programmed with
the frequency of the reference clock for the USB2.0 phy instead.
I stumbled across this while adding support for the Google Tensor
gs101, but this should apply to E850 just the same.
Do so.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-5-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using 0x82 seems odd, where everything else is just a sequence.
On E850, this macro isn't used (as a register value), only to assign
its value to the 'extrefclk' variable, which is otherwise unused on
that platform. Older platforms don't appear to support 26MHz in the
first place (since this macro was added for E850).
Furthermore, the downstream driver uses 0x82 to denote
USBPHY_REFCLK_DIFF_26MHZ (whatever that means exactly), but for all the
other values we match downstream's non-DIFF macros.
Update to avoid confusion. No functional change intended.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-4-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
on / not on is just a boolean flag and is a bit misleading as currently
on==1 means to turn off the power, and on==0 to turn power on.
Rename the flag and make it a bool to avoid confusion of future readers
of this code. No functional change.
While at it, fix a whitespace issue in nearby comment.
No functional change.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-3-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The timers-howto recommends using usleep_range() and friends anytime
waiting for >= ~10us is required. Doing so can help the timer subsystem
a lot to coalesce wakeups.
Additionally, fsleep() exists as a convenient wrapper so we do not have
to think about which exact sleeping function is required in which case.
Convert all udelay() calls in this driver to use fsleep() to follow the
recommendataion.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-2-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Most of the macros are ordered high -> low, but there are some
outliers.
Order them all uniformly from high to low. This will allow adding
additional register (field) definitions in a consistent way.
While at it, also remove some extra empty lines to group register bit
field definitions together with the relevant register. This makes the
registers easier to distinguish visually.
No functional change.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-1-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To preserve the err value, exit the loop immediately if an error
is returned.
Fixes: f2c6d0fa19 ("phy: samsung-ufs: use exynos_get_pmu_regmap_by_phandle() to obtain PMU regmap")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240426104129.2211949-3-peter.griffin@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
mfd/syscon.h header is no longer required since the update to
exynos_get_pmu_regmap_by_phandle() api.
Fixes: f2c6d0fa19 ("phy: samsung-ufs: use exynos_get_pmu_regmap_by_phandle() to obtain PMU regmap")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240426104129.2211949-2-peter.griffin@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the m-phy tuning values for gs101 UFS phy and SoC callbacks
gs101_phy_wait_for_calibration() and gs101_phy_wait_for_cdr_lock().
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240404122559.898930-12-peter.griffin@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some SoCs like gs101 don't fit in well with the existing pll lock and
clock data recovery (CDR) callback used by existing exynos platforms.
Allow SoCs to specifify and implement their own calibration and CDR
functions that can be called by the generic samsung phy code.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240404122559.898930-11-peter.griffin@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This allows us to obtain a PMU regmap that is created by the exynos-pmu
driver. Platforms such as gs101 require exynos-pmu created regmap to
issue SMC calls for PMU register accesses. Existing platforms still get
a MMIO regmap as before.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20240404122559.898930-10-peter.griffin@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The xlate callbacks are supposed to translate of_phandle_args to proper
provider without modifying the of_phandle_args. Make the argument
pointer to const for code safety and readability.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Link: https://lore.kernel.org/r/20240217093937.58234-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Implement Exynos850 USB 2.0 DRD PHY controller support. Exynos850 has
quite a different PHY controller than Exynos5 compatible controllers,
but it's still possible to implement it on top of existing
exynos5-usbdrd driver infrastructure.
Only UTMI+ (USB 2.0) PHY interface is implemented, as Exynos850 doesn't
support USB 3.0.
Only two clocks are used for this controller:
- phy: bus clock, used for PHY registers access
- ref: PHY reference clock (OSCCLK)
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230819031731.22618-7-semen.protsenko@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Modern Exynos chips (like Exynos850) might have 26 MHz OSCCLK external
clock, which is also used as a PHY reference clock. For some USB PHY
controllers (e.g USB DRD PHY block on Exynos850) there is no need to set
the refclk frequency at all (and corresponding bits in CLKRSTCTRL[7:5]
are marked RESERVED), so that value won't be set in the driver. But
even in that case, 26 MHz support still has to be added, otherwise
exynos5_rate_to_clk() fails, which leads in turn to probe error.
Add the correct value for 26MHz refclk to make it possible to add
support for new Exynos USB DRD PHY controllers.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230819031731.22618-6-semen.protsenko@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Provide a way to use different PHY ops for different chips. Right now
all chips are using exynos5_usbdrd_phy_ops, but it won't always be the
case. For example, Exynos850 has very different USB PHY block, so there
will be another PHY ops implementation for that chip.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230819031731.22618-5-semen.protsenko@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/phy/phy-can-transceiver.c
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20230714174841.4061919-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Support for the Exynos4212 SoC was originally dropped as there were
no boards using it. We will be adding a device that uses it, so add
it back.
This reverts commit fee7e1d50c.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230501195525.6268-9-aweber.kernel@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The MIPI phy is actually part of the Power Management Unit system
controller, thus it should be its child, instead of sibling node with
syscon phandle.
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20230127194057.186458-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The DisplayPort phy is actually part of the Power Management Unit system
controller, thus it should be its child, instead of sibling node with
syscon phandle.
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20230127194057.186458-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
-----BEGIN PGP SIGNATURE-----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=9TAR
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Consolidate duplicated 'next function' scanning and extend to allow
'isolated functions' on s390, similar to existing hypervisors
(Niklas Schnelle)
Resource management:
- Implement pci_iobar_pfn() for sparc, which allows us to remove the
sparc-specific pci_mmap_page_range() and pci_mmap_resource_range().
This removes the ability to map the entire PCI I/O space using
/proc/bus/pci, but we believe that's already been broken since
v2.6.28 (Arnd Bergmann)
- Move common PCI definitions to asm-generic/pci.h and rework others
to be be more specific and more encapsulated in arches that need
them (Stafford Horne)
Power management:
- Convert drivers to new *_PM_OPS macros to avoid need for '#ifdef
CONFIG_PM_SLEEP' or '__maybe_unused' (Bjorn Helgaas)
Virtualization:
- Add ACS quirk for Broadcom BCM5750x multifunction NICs that isolate
the functions but don't advertise an ACS capability (Pavan Chebbi)
Error handling:
- Clear PCI Status register during enumeration in case firmware left
errors logged (Kai-Heng Feng)
- When we have native control of AER, enable error reporting for all
devices that support AER. Previously only a few drivers enabled
this (Stefan Roese)
- Keep AER error reporting enabled for switches. Previously we
enabled this during enumeration but immediately disabled it (Stefan
Roese)
- Iterate over error counters instead of error strings to avoid
printing junk in AER sysfs counters (Mohamed Khalfella)
ASPM:
- Remove pcie_aspm_pm_state_change() so ASPM config changes, e.g.,
via sysfs, are not lost across power state changes (Kai-Heng Feng)
Endpoint framework:
- Don't stop an EPC when unbinding an EPF from it (Shunsuke Mie)
Endpoint embedded DMA controller driver:
- Simplify and clean up support for the DesignWare embedded DMA
(eDMA) controller (Frank Li, Serge Semin)
Broadcom STB PCIe controller driver:
- Avoid config space accesses when link is down because we can't
recover from the CPU aborts these cause (Jim Quinlan)
- Look for power regulators described under Root Ports in DT and
enable them before scanning the secondary bus (Jim Quinlan)
- Disable/enable regulators in suspend/resume (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Simplify and clean up clock and PHY management (Richard Zhu)
- Disable/enable regulators in suspend/resume (Richard Zhu)
- Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)
- Allow speeds faster than Gen2 (Richard Zhu)
- Make link being down a non-fatal error so controller probe doesn't
fail if there are no Endpoints connected (Richard Zhu)
Loongson PCIe controller driver:
- Add ACPI and MCFG support for Loongson LS7A (Huacai Chen)
- Avoid config reads to non-existent LS2K/LS7A devices because a
hardware defect causes machine hangs (Huacai Chen)
- Work around LS7A integrated devices that report incorrect Interrupt
Pin values (Jianmin Lv)
Marvell Aardvark PCIe controller driver:
- Add support for AER and Slot capability on emulated bridge (Pali
Rohár)
MediaTek PCIe controller driver:
- Add Airoha EN7532 to DT binding (John Crispin)
- Allow building of driver for ARCH_AIROHA (Felix Fietkau)
MediaTek PCIe Gen3 controller driver:
- Print decoded LTSSM state when the link doesn't come up (Jianjun
Wang)
NVIDIA Tegra194 PCIe controller driver:
- Convert DT binding to json-schema (Vidya Sagar)
- Add DT bindings and driver support for Tegra234 Root Port and
Endpoint mode (Vidya Sagar)
- Fix some Root Port interrupt handling issues (Vidya Sagar)
- Set default Max Payload Size to 256 bytes (Vidya Sagar)
- Fix Data Link Feature capability programming (Vidya Sagar)
- Extend Endpoint mode support to devices beyond Controller-5 (Vidya
Sagar)
Qualcomm PCIe controller driver:
- Rework clock, reset, PHY power-on ordering to avoid hangs and
improve consistency (Robert Marko, Christian Marangi)
- Move pipe_clk handling to PHY drivers (Dmitry Baryshkov)
- Add IPQ60xx support (Selvam Sathappan Periakaruppan)
- Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)
- Add support for more than 32 MSI interrupts (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Convert DT binding to json-schema (Herve Codina)
- Add Renesas RZ/N1D (R9A06G032) to rcar-gen2 DT binding and driver
(Herve Codina)
Samsung Exynos PCIe controller driver:
- Fix phy-exynos-pcie driver so it follows the 'phy_init() before
phy_power_on()' PHY programming model (Marek Szyprowski)
Synopsys DesignWare PCIe controller driver:
- Simplify and clean up the DWC core extensively (Serge Semin)
- Fix an issue with programming the ATU for regions that cross a 4GB
boundary (Serge Semin)
- Enable the CDM check if 'snps,enable-cdm-check' exists; previously
we skipped it if 'num-lanes' was absent (Serge Semin)
- Allocate a 32-bit DMA-able page to be MSI target instead of using a
driver data structure that may not be addressable with 32-bit
address (Will McVicker)
- Add DWC core support for more than 32 MSI interrupts (Dmitry
Baryshkov)
Xilinx Versal CPM PCIe controller driver:
- Add DT binding and driver support for Versal CPM5 Gen5 Root Port
(Bharat Kumar Gogada)"
* tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (150 commits)
PCI: imx6: Support more than Gen2 speed link mode
PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
PCI: imx6: Reformat suspend callback to keep symmetric with resume
PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
PCI: imx6: Disable clocks in reverse order of enable
PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
PCI: imx6: Reduce resume time by only starting link if it was up before suspend
PCI: imx6: Mark the link down as non-fatal error
PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
PCI: imx6: Turn off regulator when system is in suspend mode
PCI: imx6: Call host init function directly in resume
PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
PCI: imx6: Propagate .host_init() errors to caller
PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
PCI: imx6: Factor out ref clock disable to match enable
PCI: imx6: Move imx6_pcie_clk_disable() earlier
PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
PCI: imx6: Move PHY management functions together
PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()
...
The exynos-pcie driver called phy_power_on() before phy_init() for some
historical reasons. However the generic PHY framework assumes that the
proper sequence is to call phy_init() first, then phy_power_on(). The
operations done by both functions should be considered as one action and as
such they are called by the exynos-pcie driver (without doing anything
between them). The initialization is just a sequence of register writes,
which cannot be altered without breaking the hardware operation.
To match the generic PHY framework requirement, simply move all register
writes to the phy_init()/phy_exit() and drop power_on()/power_off()
callbacks. This way the driver will also work with the old (incorrect)
PHY initialization call sequence.
Link: https://lore.kernel.org/r/20220628220409.26545-1-m.szyprowski@samsung.com
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
The sequence of controlling ufs phy block should be below:
1) Power On
- Turn off pmu isolation
- Clock enable
2) Power Off
- Clock disable
- Turn on pmu isolation
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220706020255.151177-3-chanho61.park@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
