Looking at section "11.4.4.29 USP_PCIE_RESBAR Registers Summary" in the
Technical Reference Manual (TRM) for RK3588, we can see that none of the
BARs are Fixed BARs, but actually Resizable BARs.
I couldn't find any reference in the TRM for RK3568, but looking at the
downstream PCIe endpoint driver, both RK3568 and RK3588 are treated as
the same, so the BARs on RK3568 must also be Resizable BARs.
Now when we actually have support for Resizable BARs, let's configure
these BARs as such.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-16-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The support for a specific iATU alignment was added in
commit 2a9a801620 ("PCI: endpoint: Add support to specify alignment for
buffers allocated to BARs").
This commit specifically mentions both that the alignment by each DWC
based EP driver should match CX_ATU_MIN_REGION_SIZE, and that AM65x
specifically has a 64 KB alignment.
This also matches the CX_ATU_MIN_REGION_SIZE value specified in the
section "12.2.2.4.7 PCIe Subsystem Address Translation" of the Technical
Reference Manual (TRM) for AM65x:
https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
This higher value, 1 MB, was obviously an ugly hack used to be able to
handle Resizable BARs which have a minimum size of 1 MB.
Now when we actually have support for Resizable BARs, let's configure the
iATU alignment requirement to the actual requirement.
(BARs described as Resizable will still get aligned to 1 MB.)
Cc: stable+noautosel@kernel.org # Depends on PCI endpoint Resizable BARs series
Fixes: 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-15-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Looking at section "12.2.2.4.15 PCIe Subsystem BAR Configuration" in the
following Technical Reference Manual (TRM) for AM65x:
https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
We can see that BAR2 and BAR5 are not Fixed BARs, but actually Resizable
BARs.
Now when we actually have support for Resizable BARs, let's configure
these BARs as such.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-14-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The DWC databook specifies three different BARn_SIZING_SCHEME_N as:
- Fixed Mask (0)
- Programmable Mask (1)
- Resizable BAR (2)
Each of these sizing schemes have different instructions for how to
initialize the BAR.
The DWC driver currently does not support resizable BARs.
Instead, in order to somewhat support resizable BARs, the DWC EP driver
currently has an ugly hack that force sets a resizable BAR to 1 MB, if
such a BAR is detected.
Additionally, this hack only works if the DWC glue driver also has lied
in their EPC features, and claimed that the resizable BAR is a 1 MB fixed
size BAR.
This is unintuitive (as you somehow need to know that you need to lie in
your EPC features), but other than that it is overly restrictive, since a
resizable BAR is capable of supporting sizes different than 1 MB.
Add proper support for resizable BARs in the DWC EP driver.
Note that the pci_epc_set_bar() API takes a struct pci_epf_bar which tells
the EPC driver how it wants to configure the BAR.
struct pci_epf_bar only has a single size struct member.
This means that an EPC driver will only be able to set a single supported
size. This is perfectly fine, as we do not need the complexity of allowing
a host to change the size of the BAR. If someone ever wants to support
resizing a resizable BAR, the pci_epc_set_bar() API can be extended in the
future.
With these changes, we allow an EPF driver to configure the size of
Resizable BARs, rather than forcing them to a 1 MB size.
This means that an EPC driver does not need to lie in EPC features, and an
EPF driver will be able to set an arbitrary size (not be forced to a 1 MB
size), just like BAR_PROGRAMMABLE.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-13-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Move dw_pcie_ep_find_ext_capability() so that it is located next to
dw_pcie_ep_find_capability().
Additionally, a follow-up commit requires this to be defined earlier
in order to avoid a forward declaration.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-12-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add a helper function to convert a size to the representation used by the
Resizable BAR Capability Register.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-11-cassel@kernel.org
[mani: squashed the change that added PCIe spec reference to comments
from https://lore.kernel.org/linux-pci/20250219171454.2903059-2-cassel@kernel.org]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
A resizable BAR is different from a normal BAR in a few ways:
- The minimum size of a resizable BAR is 1 MB.
- Each BAR that is resizable has a Capability and Control register in
the Resizable BAR Capability structure.
These registers contain the supported sizes and the currently selected
size of a resizable BAR.
The supported sizes is a bitmap of the supported sizes. The selected size
is a single value that is equal to one of the supported sizes.
A resizable BAR thus has to be configured differently than a
BAR_PROGRAMMABLE BAR, which usually sets the BAR size/mask in a vendor
specific way.
The PCI endpoint framework currently does not support resizable BARs.
Add a BAR type BAR_RESIZABLE, so that an EPC driver can support resizable
BARs properly.
Note that the pci_epc_set_bar() API takes a struct pci_epf_bar which tells
the EPC driver how it wants to configure the BAR.
struct pci_epf_bar only has a single size struct member.
This means that an EPC driver will only be able to set a single supported
size. This is perfectly fine, as we do not need the complexity of allowing
a host to change the size of the BAR. If someone ever wants to support
resizing a resizable BAR, the pci_epc_set_bar() API can be extended in the
future.
With these changes, we allow an EPF driver to configure the size of
Resizable BARs, rather than forcing them to a 1 MB size.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-10-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The struct pci_epf_test_reg is the actual data in pci-epf-test's test_reg
BAR (usually BAR0), which the host uses to send commands (etc.), and which
pci-epf-test uses to send back status codes.
pci-epf-test currently reads and writes this data without any endianness
conversion functions, which means that pci-epf-test is completely broken
on big-endian endpoint systems.
PCI devices are inherently little-endian, and the data stored in the PCI
BARs should be in little-endian.
Use endianness conversion functions when reading and writing data to
struct pci_epf_test_reg so that pci-epf-test will behave correctly on
big-endian endpoint systems.
Fixes: 349e7a85b2 ("PCI: endpoint: functions: Add an EP function to test PCI")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250127161242.104651-2-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
pci_release_resource() will print "... releasing" regardless of the
resource being assigned or not. Move the print after the res->parent check
to avoid claiming the kernel would be releasing an unassigned resource.
Likely, none of the current callers pass a resource that is unassigned so
this change is mostly to correct the non-sensical order than to remove
errorneous printouts.
Link: https://lore.kernel.org/r/20250307140922.5776-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r6.0, sec 7.8.6.2, devices can advertise Resizable BAR sizes up to
128 TB in the Resizable BAR Capability register. Larger sizes can be
advertised via the Capability register, but that requires an API change.
Update pci_rebar_get_possible_sizes() and pbus_size_mem() to increase the
sizes we currently support from 512 GB to 128 TB.
Link: https://lore.kernel.org/r/20250307053535.44918-1-daizhiyuan@phytium.com.cn
Signed-off-by: Zhiyuan Dai <daizhiyuan@phytium.com.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe r6.1, sec 6.30.1.1, describes a "Vendor ID", a "Data Object Type" and
"Next Index" as the fields in the DOE Discovery Response Data Object. The
DOE driver currently uses both the terms 'type' and 'prot' for the second
element.
Rename all uses of the DOE Discovery Response Data Object to use 'type' as
the second element of the object header, instead of type/prot as it
currently is.
Link: https://lore.kernel.org/r/20250306075211.1855177-2-alistair@alistair23.me
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
DOE r1.1 replaced all occurrences of "protocol" with the term "feature" or
"Data Object Type". PCIe r6.1 incorporated that change.
Rename the existing terms protocol with feature.
Link: https://lore.kernel.org/r/20250306075211.1855177-1-alistair@alistair23.me
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Add PCIe Root Port controller support for the Agilex family of chips.
The Agilex PCIe Hard IP has three variants that are mostly software
compatible, except for a couple register offsets. The P-Tile variant
supports Gen3/Gen4 1x16. The F-Tile variant supports Gen3/Gen4 4x4,
4x8, and 4x16. The R-Tile variant improves on the F-Tile variant by
adding Gen5 support.
To simplify the implementation of pci_ops read/write functions,
ep_{read/write}_cfg() callbacks were added to struct altera_pci_ops
to easily distinguish between hardware variants.
Signed-off-by: D M, Sharath Kumar <sharath.kumar.d.m@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250221170452.875419-3-matthew.gerlach@linux.intel.com
[kwilczynski: tidy code comments]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-7-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-6-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-5-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-4-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The combination of dev_err() and the returned error code could be
replaced by dev_err_probe() in driver's probe function.
Thus, convert the code to use dev_err_probe() to make code simpler.
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240831040413.126417-3-zhangzekun11@huawei.com
[kwilczynski: commit log, return -ETIMEDOUT from hi3660_pcie_phy_start()
rather than -EINVAL for when the PIPE clock fails to become stable,
drop redundant dev->of_node NULL check]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Move PCI_VENDOR_ID_ROCKCHIP from pci_endpoint_test.c to pci_ids.h and
reuse it in pcie-rockchip-host.c.
Link: https://lore.kernel.org/r/20250218092120.2322784-2-cassel@kernel.org
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add the debugfs property to provide a view of the current link's LTSSM
status from the Root Port device.
Signed-off-by: Hans Zhang <18255117159@163.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Niklas Cassel <cassel@kernel.org>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250223141848.231232-1-18255117159@163.com
[kwilczynski: commit log, refactor dw_ltssm_sts_string() to avoid
compilation errors on platforms that do not set CONFIG_PCIE_DW_HOST]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add support to provide Statistical Counter interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-6-shradha.t@samsung.com
[kwilczynski: commit log, tidy up code comments, update documentation,
squashed patch that checks if the event counter is supported from
https://lore.kernel.org/linux-pci/20250225171239.19574-3-manivannan.sadhasivam@linaro.org]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add support to provide Error Injection interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-5-shradha.t@samsung.com
[kwilczynski: commit log, tidy up code comments, update documentation,
change debugfs property name from "duplicate_dllp" to "duplicate_tlp"]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add support to provide Silicon Debug interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-4-shradha.t@samsung.com
[kwilczynski: commit log, tidy up Kconfig and drop "default y", tidy up
code comments, squashed patch that fixes a NULL pointer dereference when
debugfs is already unavailable during clean-up from
https://lore.kernel.org/linux-pci/20250225171239.19574-2-manivannan.sadhasivam@linaro.org,
refactor dwc_pcie_debugfs_init() to not return errors, squashed patch that
changes how lack of the RAS DES capability is handled from
https://lore.kernel.org/linux-pci/20250304151814.6xu7cbpwpqrvcad5@thinkpad]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Fix the following inconsistent indentation warning:
drivers/pci/controller/pcie-mediatek-gen3.c:922 mtk_pcie_parse_port() warn: inconsistent indenting
Found using Smatch. No functional changes intended.
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://lore.kernel.org/r/20250305070022.4668-1-hanchunchao@inspur.com
[kwilczynski: commit log, refactor if-statement around num_lanes to
make it more readable, wrap overly long lines to fit 80 colums]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-2-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
After d88f521da3 ("PCI: Allow userspace to query and set device reset
mechanism"), userspace can disable reset of specific PCI devices by writing
an empty string to the sysfs reset_method file.
However, pci_slot_resettable() does not check pci_reset_supported(), which
means that pci_reset_function() will still reset the device even if
userspace has disabled all the reset methods.
I was able to reproduce this issue with a vfio device passed to a qemu
guest, where I had disabled PCI reset via sysfs.
Add an explicit check of pci_reset_supported() in both
pci_slot_resettable() and pci_bus_resettable() to ensure both the reset
status and reset execution are bypassed if an administrator disables it for
a device.
Link: https://lore.kernel.org/r/20250207205600.1846178-1-naravamudan@nvidia.com
Fixes: d88f521da3 ("PCI: Allow userspace to query and set device reset mechanism")
Signed-off-by: Nishanth Aravamudan <naravamudan@nvidia.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Raphael Norwitz <raphael.norwitz@nutanix.com>
Cc: Amey Narkhede <ameynarkhede03@gmail.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Yishai Hadas <yishaih@nvidia.com>
Cc: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Firmware developers reported that Linux issues two PCIe hotplug commands in
very short intervals on an ARM server, which doesn't comply with the PCIe
spec. According to PCIe r6.1, sec 6.7.3.2, if the Command Completed event
is supported, software must wait for a command to complete or wait at
least 1 second before sending a new command.
In the failure case, the first PCIe hotplug command is from
get_port_device_capability(), which sends a command to disable PCIe hotplug
interrupts without waiting for its completion, and the second command comes
from pcie_enable_notification() of pciehp driver, which enables hotplug
interrupts again.
Fix this by only disabling the hotplug interrupts when the pciehp driver is
not enabled.
Link: https://lore.kernel.org/r/20250303023630.78397-1-feng.tang@linux.alibaba.com
Fixes: 2bd50dd800 ("PCI: PCIe: Disable PCIe port services during port initialization")
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Feng Tang <feng.tang@linux.alibaba.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
For no apparent reason, the pci_hp_{create,remove}_module_link() helpers
live in slot.c, even though they're only called from two functions in
pci_hotplug_core.c.
Inline the helpers to reduce code size and number of exported symbols.
Link: https://lore.kernel.org/r/c207f03cfe32ae9002d9b453001a1dd63d9ab3fb.1740501868.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI hotplug core contains five has_*_file() functions to determine
whether a certain sysfs file shall be added (or removed) for a given
hotplug slot.
The functions receive a struct pci_slot pointer which they have to
dereference back to a struct hotplug_slot.
Avoid by passing them a struct hotplug_slot pointer directly.
Link: https://lore.kernel.org/r/5b2f5b4ac45285953d00fd7637732a93fd40d26e.1740501868.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI hotplug core contains five has_*_file() functions to determine
whether a certain sysfs file shall be added (or removed) for a given
hotplug slot.
The functions perform NULL pointer checks for the hotplug_slot and its
hotplug_slot_ops. However the callers already perform these checks:
pci_hp_register()
__pci_hp_register()
__pci_hp_initialize()
pci_hp_deregister()
pci_hp_del()
The only way to actually trigger these checks is to call pci_hp_add()
without having called pci_hp_initialize().
Amend pci_hp_add() to catch that and drop the now superfluous NULL
pointer checks in has_*_file().
Drop the same superfluous checks from pci_hp_create_module_link(),
which is (only) called from pci_hp_add().
Link: https://lore.kernel.org/r/37d1928edf8c3201a8b10794f1db3142e16e02b9.1740501868.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In December 2002, historic commit
https://git.kernel.org/tglx/history/c/bec7aa00ffe5
("[PATCH] more module warning fixes")
amended the PCI hotplug core to acquire a reference on the hotplug
driver module when a sysfs attribute is accessed. That was necessary
because back in the day, sysfs code did not take any precautions to
prevent module unloading when an attribute was accessed.
Soon after in July 2003, historic commit
https://git.kernel.org/tglx/history/c/1cf6d20f6078
("[PATCH] SYSFS: add module referencing to sysfs attribute files.")
addressed that deficiency. But the commit neglected to remove the now
unnecessary reference acquisition from the PCI hotplug core.
The commit acquired a module reference for the entire duration between
open() and close() of a sysfs attribute. This made it impossible to
unload a module while attributes were kept open by user space.
That's possible today:
When a hotplug driver module is unloaded, it removes sysfs attributes of
all its hotplug slots by calling pci_hp_del(). This will wait for any
concurrent user space operation to finish:
pci_hp_del()
fs_remove_slot()
sysfs_remove_file()
sysfs_remove_file_ns()
kernfs_remove_by_name_ns()
__kernfs_remove()
kernfs_drain()
A user space operation such as read() briefly acquires a reference on
the attribute with kernfs_get_active(). kernfs_drain() waits until all
such references are released before allowing attribute removal. Once
the attribute is removed, any subsequent user space operation on a still
open attribute file will return -ENODEV.
Thus, reference acquisition by the PCI hotplug core is still unnecessary
today. So drop it at long last.
Link: https://lore.kernel.org/r/ed950fa2722967be4491146c7b867c1e7be11d37.1740501868.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI hotplug core keeps a list of all registered slots. Its sole
purpose is to WARN() on slot removal if another slot is using the same
name.
But this can never happen because already on slot creation, an error is
returned and multiple messages are emitted if a slot's name is
duplicated:
pci_hp_register()
__pci_hp_register()
__pci_hp_initialize()
pci_create_slot()
kobject_init_and_add()
kobject_add_varg()
kobject_add_internal()
create_dir()
sysfs_create_dir_ns()
kernfs_create_dir_ns()
sysfs_warn_dup()
pr_warn("cannot create duplicate filename ...")
pr_err("%s failed for %s with -EEXIST, ...");
Drop the superfluous list.
Link: https://lore.kernel.org/r/603735bc50eb370bc7f1c358441ac671360bab25.1740501868.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Log pci_dbg() messages about the reset methods we attempt and any errors
(-ENOTTY means "try the next method").
Set CONFIG_DYNAMIC_DEBUG=y and enable by booting with
dyndbg="file drivers/pci/* +p" or enable at runtime:
# echo "file drivers/pci/* +p" > /sys/kernel/debug/dynamic_debug/control
Link: https://lore.kernel.org/r/20250303204220.197172-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Make the cast to the irq_hw_number_t type for the parameter passed to
irq_domain_set_info() function explicit.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-9-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The hardware has been updated with two changes to the MDIO packet
format.
The CMD field used to be 12 bits and now is only 1 bit. This change
is backwards compatible because the field's starting bit position is
unchanged, and the only commands we've used have values 0 and 1.
The PORT field's width has been changed from 4 bits to 5 bits. When
written, the new bit is not contiguous with the other four. However,
this change is backwards compatible because the driver never used
anything other than 0 for the port field's value.
Thus, update the existing code to handle new changes to the hardware
in a backwards-compatible manner.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-8-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The constants EXT_CFG_DATA and EXT_CFG_INDEX vary by SoC, where one of
the map_bus methods used these constants, and the other used a different
set of constants.
Thankfully, there was no problem because the SoCs that used the latter
map_bus method all had the same register constants.
Thus, remove redundant constants and adjust the code to use the correct
constants accordingly.
While at it, update the value of EXT_CFG_DATA to use the 4k-page based
configuration space access system, which is what the second map_bus
method was already using.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250214173944.47506-7-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The platform supports enabling and disabling regulators only on
ports below the Root Complex.
Thus, we need to verify this both when adding and removing the bus,
otherwise regulators may be disabled prematurely when a bus further
down the topology is removed.
Fixes: 9e6be018b2 ("PCI: brcmstb: Enable child bus device regulators from DT")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-6-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
If the regulator_bulk_get() returns an error and no regulators
are created, we need to set their number to zero.
If we don't do this and the PCIe link up fails, a call to the
regulator_bulk_free() will result in a kernel panic.
While at it, print the error value, as we cannot return an error
upwards as the kernel will WARN() on an error from add_bus().
Fixes: 9e6be018b2 ("PCI: brcmstb: Enable child bus device regulators from DT")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250214173944.47506-5-james.quinlan@broadcom.com
[kwilczynski: commit log, use comma in the message to match style with
other similar messages]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
When setting the LNKCAP and LNKCTL2 register fields, it was assumed
that the field started at the LSB of the register.
Although the masks do indeed start at the LSB, and this will probably
not change, it is prudent to use a method that makes no assumption
about the mask's placement in the register.
Thus, use the u{16,32}p_replace_bits() helpers since they are already
wildly used in this driver.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-4-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The driver has been mistakenly writing to a read-only (RO)
configuration space register (PCI_EXP_LNKCAP) to change the
PCIe link capability.
Although harmless in this case, the proper write destination
is an internal register that is reflected by PCI_EXP_LNKCAP.
Thus, fix the brcm_pcie_set_gen() function to correctly update
the link capability.
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-3-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
When the user elects to limit the PCIe generation via the appropriate
devicetree property, apply the settings before the PCIe link up, not
after.
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-2-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add a bare minimum amount of changes in order to support PCIe Root
Complex hardware IP found on RPi5. The PCIe controller on BCM2712
is based on BCM7712 and as such it inherits register offsets, PERST#
assertion, bridge_reset ops, and inbound windows count.
Although, the implementation for BCM2712 needs a workaround related to
the control of the bridge_reset where turning off of the Root Port must
not shutdown the bridge_reset and this must be avoided. To implement
this workaround a quirks field is introduced in pcie_cfg_data struct.
The controller also needs adjustment of PHY PLL setup to use a 54MHz
input refclk. The default input reference clock for the PHY PLL is
100Mhz, except for some devices where it is 54Mhz like BCM2712C1 and
BCM2712D0.
To implement those adjustments introduce a new .post_setup op in
pcie_cfg_data and call it at the end of brcm_pcie_setup function.
The BCM2712 .post_setup callback implements the required MDIO writes
that switch the PLL refclk and also change PHY PM clock period.
Without this RPi5 PCIex1 is unable to enumerate endpoint devices on
the expansion connector.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-8-svarbanov@suse.de
[commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Per the Cadence's "PCIe Controller IP for AX14" user guide, Version
1.04, Section 9.1.7.1, "AXI Subordinate to PCIe Address Translation
Registers", Table 9.4, the bit 16 of the AXI Subordinate Address
(axi_s_awaddr) when set corresponds to MSG with data, and when not set,
to MSG without data.
However, the driver is currently doing the opposite and due to this,
the INTx is never received on the host.
So, fix the driver to reflect the documentation and also make INTx work.
Fixes: 37dddf14f1 ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Hans Zhang <hans.zhang@cixtech.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214165724.184599-1-18255117159@163.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The new dw_pcie_find_vsec_capability() helper will be used within
different DWC APIs to find the VSEC capabilities like PTM, RAS, etc.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-3-shradha.t@samsung.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Configure PBus base address and address mask to allow the hw
to detect if a given address is accessible on PCIe controller.
Fixes: f6ab898356 ("PCI: mediatek-gen3: Add Airoha EN7581 support")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20250225-en7581-pcie-pbus-csr-v4-2-24324382424a@kernel.org
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
PCI devices device tree nodes can be already created. This was introduced
by commit 407d1a5192 ("PCI: Create device tree node for bridge").
In order to have device tree nodes related to PCI devices attached on their
PCI root bus (the PCI bus handled by the PCI host bridge), a PCI root bus
device tree node is needed. This root bus node will be used as the parent
node of the first level devices scanned on the bus. On device tree based
systems, this PCI root bus device tree node is set to the node of the
related PCI host bridge. The PCI host bridge node is available in the
device tree used to describe the hardware passed at boot.
On non device tree based system (such as ACPI), a device tree node for the
PCI host bridge or for the root bus does not exist. Indeed, the PCI host
bridge is not described in a device tree used at boot simply because no
device tree is passed at boot.
The device tree PCI host bridge node creation needs to be done at runtime.
This is done in the same way as for the creation of the PCI device nodes.
I.e. node and properties are created based on computed information done by
the PCI core. Also, as is done on device tree based systems, this PCI host
bridge node is used for the PCI root bus.
With this done, hardware available in a PCI device that doesn't follow the
PCI model consisting in one PCI function handled by one driver can be
described by a device tree overlay loaded by the PCI device driver on non
device tree based systems. Those PCI devices provide a single PCI function
that includes several functionalities that require different drivers. The
device tree overlay describes the internal devices and their relationships.
It allows to load drivers needed by those different devices in order to
have functionalities handled.
Link: https://lore.kernel.org/r/20250224141356.36325-6-herve.codina@bootlin.com
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
The res parameter has no reason to be a pointer to an un-const struct
resource. Indeed, struct resource is not supposed to be modified by the
function.
Constify the res parameter.
Link: https://lore.kernel.org/r/20250224141356.36325-5-herve.codina@bootlin.com
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
The pdev (pointer to a struct pci_dev) parameter of of_pci_set_address()
cannot be NULL.
In order to use of_pci_set_address() when creating the PCI root bus node,
it needs to support a NULL pdev parameter. Indeed, in the case of the PCI
root bus node creation, no pdev is available and of_pci_set_address() will
be used with the bridge windows.
Allow to call of_pci_set_address() with a NULL pdev.
Link: https://lore.kernel.org/r/20250224141356.36325-4-herve.codina@bootlin.com
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
The commit 407d1a5192 ("PCI: Create device tree node for bridge")
creates of_node for PCI devices. The newly created of_node is attached
to an existing device. This is done setting directly pdev->dev.of_node
in the code.
Even if pdev->dev.of_node cannot be previously set, this doesn't handle
the fwnode field of the struct device. Indeed, this field needs to be
set if it hasn't already been set.
device_{add,remove}_of_node() have been introduced to handle this case.
Use them instead of the direct setting.
Link: https://lore.kernel.org/r/20250224141356.36325-3-herve.codina@bootlin.com
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
The BCM2712 memory map can support up to 64GB of system memory, thus
expand the inbound window size in calculation helper function.
The change is safe for the currently supported SoCs that have smaller
inbound window sizes.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-7-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Instead of copying fields from the pcie_cfg_data structure to
brcm_pcie, reference it directly.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelil <florian.fainelli@broadcom.com>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-6-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Then the brcmstb PCIe driver and MIP MSI-X interrupt controller
drivers are built as modules there could be a race in probing.
To avoid this, add a softdep to MIP driver to guarantee that
MIP driver will be load first.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-5-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Calling cpumask_next_wrap_old() with starting CPU == nr_cpu_ids
is effectively the same as request to find first CPU, starting
from a given one and wrapping around if needed.
cpumask_next_wrap() is a proper replacement for that.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
The next patch aligns implementation of cpumask_next_wrap() with the
find_next_bit_wrap(), and it changes function signature.
To make the transition smooth, this patch deprecates current
implementation by adding an _old suffix. The following patches switch
current users to the new implementation one by one.
No functional changes were intended.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Enable PCIe Endpoint mode support for the Qualcomm SAR2130P platform.
This is needed, as it is not possible to use a compatible fallback on
any other platform since SAR2130P uses slightly different set of clocks.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250221-sar2130p-pci-v3-6-61a0fdfb75b4@linaro.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
A call to of_parse_phandle() is incrementing the refcount, and as such,
the of_node_put() must be called when the reference is no longer needed.
Thus, refactor the existing code and add a missing of_node_put() call
following the check to ensure that "msi_np" matches "pcie->np" and after
MSI initialization, but only if the MSI support is enabled system-wide.
Cc: stable@vger.kernel.org # v5.10+
Fixes: 40ca1bf580 ("PCI: brcmstb: Add MSI support")
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250122222955.1752778-1-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
On all Qcom endpoint SoCs, BAR0/BAR2 are 64bit BARs by default and
software cannot change the type.
So, mark the those BARs as 64bit BARs and also mark the successive
BAR1/BAR3 as RESERVED BARs so that the EPF drivers cannot use them.
Cc: stable+noautosel@kernel.org # depends on patch introducing only_64bit flag
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241231130224.38206-3-manivannan.sadhasivam@linaro.org
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
When CONFIG_PCI_P2PDMA=y (which is basically enabled on all
large x86 distros), it maps the PFN's via a ZONE_DEVICE
mapping using devm_memremap_pages(). The mapped virtual
address range corresponds to the pci_resource_start()
of the BAR address and size corresponding to the BAR length.
When KASLR is enabled, the direct map range of the kernel is
reduced to the size of physical memory plus additional padding.
If the BAR address is beyond this limit, PCI peer to peer DMA
mappings fail.
Fix this by not shrinking the size of the direct map when
CONFIG_PCI_P2PDMA=y.
This reduces the total available entropy, but it's better than
the current work around of having to disable KASLR completely.
[ mingo: Clarified the changelog to point out the broad impact ... ]
Signed-off-by: Balbir Singh <balbirs@nvidia.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # drivers/pci/Kconfig
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Link: https://lore.kernel.org/lkml/20250206023201.1481957-1-balbirs@nvidia.com/
Link: https://lore.kernel.org/r/20250206234234.1912585-1-balbirs@nvidia.com
--
arch/x86/mm/kaslr.c | 10 ++++++++--
drivers/pci/Kconfig | 6 ++++++
2 files changed, 14 insertions(+), 2 deletions(-)
The .get_power() and .set_power() function pointers in struct
cpci_hp_controller_ops were declared but never implemented by any
driver.
Thus, to improve code readability and reduce resource usage,
remove these pointers and the code that has never been used.
Link: https://lore.kernel.org/r/20250217185638.398925-1-trintaeoitogc@gmail.com
Signed-off-by: Guilherme Giacomo Simoes <trintaeoitogc@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Flit mode introduced in PCIe r6.0 alters how the TLP Header Log is
presented through AER and DPC Capability registers. The TLP Prefix Log
Register is not present with Flit mode, and the register becomes an
extension of the TLP Header Log (PCIe r6.1 secs 7.8.4.12 & 7.9.14.13).
Adapt pcie_read_tlp_log() and struct pcie_tlp_log to read and store the
extended TLP Header Log when the Link is in Flit mode. As the Prefix Log
and Extended TLP Header are not present at the same time, a C union can be
used.
Determining whether the error occurred while the Link was in Flit mode is a
bit complicated. In case of AER, the Advanced Error Capabilities and
Control Register directly tells whether the error was logged in Flit mode
or not (PCIe r6.1 sec 7.8.4.7). The DPC Capability (PCIe r6.1 sec 7.9.14),
unfortunately, does not contain the same information.
Unlike AER, the DPC Capability does not provide a way to discern whether
the error was logged in Flit mode (this is confirmed by PCI WG to be an
oversight in the spec). DPC will bring the Link down immediately following
an error, which makes it impossible to acquire the Flit Mode Status
directly from the Link Status 2 register because Flit Mode Status is only
set in certain Link states (PCIe r6.1 sec 7.5.3.20). As a workaround, use
the flit_mode value stored into the struct pci_bus.
Link: https://lore.kernel.org/r/20250207161836.2755-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe r6.0 added Flit mode, which mainly alters HW behavior, but there are
some OS visible changes. The OS visible changes include differences in the
layout of some capabilities and interpretation of the TLP headers (in
diagnostics situations).
To be able to determine which mode the PCIe Link is using, store the Flit
Mode Status (PCIe r6.1 sec 7.5.3.20) information in addition to the Link
speed into struct pci_bus in pcie_update_link_speed().
Link: https://lore.kernel.org/r/20250207161836.2755-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: use unsigned int:1 instead of bool, update flit_mode setting]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
include/linux/pci.h provides low-level pci_printk() interface that is
only used by AER because it needs to print the same message with
different levels depending on the error severity. No other PCI code
uses that functionality and calls pci_<level>() logging functions
directly with the appropriate level.
Descope pci_printk() into AER as aer_printk().
Link: https://lore.kernel.org/r/20241216161012.1774-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: retain pci_printk() for now since shpchp still uses it and I
moved those patches to a different branch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove a leftover assert for mac_reset line in mtk_pcie_en7581_power_up().
This is not harmful since EN7581 does not requires mac_reset and
mac_reset is not defined in EN7581 device tree.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20250201-pcie-en7581-remove-mac_reset-v2-1-a06786cdc683@kernel.org
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
This driver is used to control the power state of the devices attached to
the PCI slots. Currently, it controls the voltage rails of the PCI slots
defined in the devicetree node of the root port.
The voltage rails for PCI slots are documented in the DT-schema:
https://github.com/devicetree-org/dt-schema/blob/v2024.11/dtschema/schemas/pci/pci-bus-common.yaml#L153
Since this driver has to work with different kind of slots (PCIe
x1/x4/x8/x16, Mini PCIe, PCI, etc.), the driver is thus using the
of_regulator_bulk_get_all() API to obtain the voltage regulators defined
in the DT node, instead of hardcoding them.
As such, the DT node of the root port should define the relevant supply
properties corresponding to the voltage rails of the PCI slot.
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250116-pci-pwrctrl-slot-v3-5-827473c8fbf4@linaro.org
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The VF driver controls an endpoint attached to the PCI HyperV
controller. An invalidation sent by the PF driver in the host
would be delivered *to* the endpoint driver by the controller
driver.
Thus, correct the wording within the comment.
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20250207190716.89995-1-eahariha@linux.microsoft.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The pwrctrl core will rescan the bus once the device is powered on. So
there is no need to continue scanning for the device further.
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250116-pci-pwrctrl-slot-v3-3-827473c8fbf4@linaro.org
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The PCI core will try to access the devices even after pci_stop_dev()
for things like Data Object Exchange (DOE), ASPM, etc.
So, move pci_pwrctrl_unregister() to the near end of pci_destroy_dev()
to make sure that the devices are powered down only after the PCI core
is done with them.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250116-pci-pwrctrl-slot-v3-2-827473c8fbf4@linaro.org
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Current way of creating pwrctrl devices requires iterating through the
child devicetree nodes of the PCI bridge in pci_pwrctrl_create_devices().
Even though it works, it creates confusion as there is no symmetry between
this and pci_pwrctrl_unregister() function that removes the pwrctrl
devices.
So to make these two functions symmetric, move the creation of pwrctrl
devices to pci_scan_device(). During the scan of each device in a slot,
the devicetree node (if exists) for the PCI device will be checked. If it
has the supplies populated, then the pwrctrl device will be created.
Since the PCI device scan happens so early, there would be no "struct
pci_dev" available for the device. So the host bridge is used as the
parent of all pwrctrl devices.
One nice side effect of this move is that, it is now possible to have
pwrctrl devices for PCI bridges as well (to control the supplies of PCI
slots).
Suggested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250116-pci-pwrctrl-slot-v3-1-827473c8fbf4@linaro.org
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Before 456d8aa37d ("PCI/ASPM: Disable ASPM on MFD function removal to
avoid use-after-free"), we would free the ASPM link only after the last
function on the bus pertaining to the given link was removed.
That was too late. If function 0 is removed before sibling function,
link->downstream would point to free'd memory after.
After above change, we freed the ASPM parent link state upon any function
removal on the bus pertaining to a given link.
That is too early. If the link is to a PCIe switch with MFD on the upstream
port, then removing functions other than 0 first would free a link which
still remains parent_link to the remaining downstream ports.
The resulting GPFs are especially frequent during hot-unplug, because
pciehp removes devices on the link bus in reverse order.
On that switch, function 0 is the virtual P2P bridge to the internal bus.
Free exactly when function 0 is removed -- before the parent link is
obsolete, but after all subordinate links are gone.
Link: https://lore.kernel.org/r/e12898835f25234561c9d7de4435590d957b85d9.1734924854.git.dns@arista.com
Fixes: 456d8aa37d ("PCI/ASPM: Disable ASPM on MFD function removal to avoid use-after-free")
Signed-off-by: Daniel Stodden <dns@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The "shpchp_debug" module parameter is used to enable debug logging. The
generic ability to turn on/off debug prints dynamically covers this use
case already so there is no need for module specific debug handling. The
ctrl_dbg() wrapper also uses a low-level pci_printk() despite always using
KERN_DEBUG level.
Remove "shpchp_debug" parameter and convert ctrl_dbg() to use pci_dbg().
From now on, shpchp can be debugged using the normal dynamic debugger by
setting CONFIG_DYNAMIC_DEBUG=y and then either adding to kernel cmdline:
dyndbg="file drivers/pci/hotplug/shpchp* +p"
or using this command on a running kernel:
echo 'file drivers/pci/hotplug/shpchp* +p' > /sys/kernel/debug/dynamic_debug/control
Link: https://lore.kernel.org/r/20250217095550.2789-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The shpchp hotplug driver defines logging wrapper with generic names which
are just duplicates of existing generic printk() wrappers. They are also
unused so remove them.
Link: https://lore.kernel.org/r/20250217095550.2789-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A recent discussion has revealed that using DPM_FLAG_SMART_SUSPEND
unconditionally is generally problematic because it may lead to
situations in which the device's runtime PM information is internally
inconsistent or does not reflect its real state [1].
For this reason, change the handling of DPM_FLAG_SMART_SUSPEND so that
it is only taken into account if it is consistently set by the drivers
of all devices having any PM callbacks throughout dependency graphs in
accordance with the following rules:
- The "smart suspend" feature is only enabled for devices whose drivers
ask for it (that is, set DPM_FLAG_SMART_SUSPEND) and for devices
without PM callbacks unless they have never had runtime PM enabled.
- The "smart suspend" feature is not enabled for a device if it has not
been enabled for the device's parent unless the parent does not take
children into account or it has never had runtime PM enabled.
- The "smart suspend" feature is not enabled for a device if it has not
been enabled for one of the device's suppliers taking runtime PM into
account unless that supplier has never had runtime PM enabled.
Namely, introduce a new device PM flag called smart_suspend that is only
set if the above conditions are met and update all DPM_FLAG_SMART_SUSPEND
users to check power.smart_suspend instead of directly checking the
latter.
At the same time, drop the power.set_active flage introduced recently
in commit 3775fc538f ("PM: sleep: core: Synchronize runtime PM status
of parents and children") because it is now sufficient to check
power.smart_suspend along with the dev_pm_skip_resume() return value
to decide whether or not pm_runtime_set_active() needs to be called
for the device.
Link: https://lore.kernel.org/linux-pm/CAPDyKFroyU3YDSfw_Y6k3giVfajg3NQGwNWeteJWqpW29BojhQ@mail.gmail.com/ [1]
Fixes: 7585946243 ("PM: sleep: core: Restrict power.set_active propagation")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # drivers/pci
Link: https://patch.msgid.link/1914558.tdWV9SEqCh@rjwysocki.net
Remove and rescan cycle can result in failure to assign a bridge window if
it becomes larger than before the remove. The bridge window size will
include space for disabled Expansion ROM, which can causes the bridge
window to not fit anymore into the same address space slot on rescan if the
Expansion ROM resource was not assigned before the remove. In addition, the
optional resource handling is not internally consistent.
The resource fitting logic supports three main types of optional resources:
- IOV BARs
- Expansion ROMs
- Bridge window size variation due to optional resources
In addition to the above, resizable BARs beyond their current size will
require handling optional variation in resource sizes within the resource
fitting algorithm (not yet done by the resource fitting code).
There are multiple inconsistencies related to optional resource handling:
a) The allocation failure of disabled expansion ROM requires special case
inside assign_requested_resources_sorted().
b) The optionality of disabled expansion ROM is not considered during
bridge window sizing in pbus_size_mem().
c) Setting resource size to zero for optional resource in pbus_size_mem()
is problematic because it makes also the alignment invalid, which is
checked by pdev_sort_resources().
Optional IOV resources have their size set to zero by pbus_size_mem()
but the information about size is stored externally in struct pci_sriov
and complex call-chain trickery in pci_resource_alignment() ensures IOV
resources return a valid alignment despite having zero resource size. A
solution that is specific to IOV resources makes it hard to use the same
solution for other types of resources such as expansion ROM.
Simply changing pbus_size_mem() is not sufficient to fully address the main
issue because it would introduce disparity between bridge window sizing and
resource allocation. Due to size-based ordering of the resource list during
assignment loop, an Expansion ROM resource could steal space from some
other resource and make the other resource not fit if the Expansion ROM is
larger than the other resource. Thus, the resource assignment functions
need to be changed as well.
Make optional resource handling more straightforward. Use
pci_resource_is_optional() to determine if a resource is optional in both
bridge window sizing and assignment failure classification to ensure they
always align. Indicate with a parameter to
assign_requested_resources_sorted() whether it should attempt to allocate
optional resources or not.
Always try first to assign all resources (also when realloc_head is not
provided). This is required for calls from
pci_assign_unassigned_root_bus_resources() that provide realloc_head only
with some of its iterations.
Non-bridge-window optional resources in realloc_head now have add_size 0.
This condition has to be detected in reassign_resources_sorted() before
reassigning them (which would fail as there is no size change). Removing
add_size=0 optional resources entirely from realloc_head might eventually
be doable but further rework in __assign_resources_sorted() is needed first
to support such a change.
Link: https://lore.kernel.org/r/20241216175632.4175-26-ilpo.jarvinen@linux.intel.com
Reported-by: Jia Yao <jia.yao@intel.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219547
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jia Yao <jia.yao@intel.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Resetting a resource is problematic as it prevents attempting to allocate
the resource later, unless something in between restores the resource.
Similarly, if fail_head does not contain all resources that were reset,
those resources cannot be restored later.
The entire reset/restore cycle adds complexity and leaving resources in the
reset state causes issues to other code such as for checks done in
pci_enable_resources(). Take a small step towards not resetting resources
by delaying reset until the end of resource assignment and build failure
list (fail_head) in sync with the reset to avoid leaving behind resources
that cannot be restored (for the case where the caller provides fail_head
in the first place to allow restore somewhere in the callchain, as is not
all callers pass non-NULL fail_head).
Leave the Expansion ROM check temporarily in place while building the
failure list until an upcoming change that reworks optional resource
handling.
Ideally, whole resource reset could be removed but doing that in one step
would be non-tractable due to complexity of all related code.
Link: https://lore.kernel.org/r/20241216175632.4175-25-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
reassign_resources_sorted() uses resource_size() to select between
pci_assign_resource() and pci_reassign_resource(). Due to twisted way
bridge window sizing in pbus_size_mem() sets resource sizes to 0, it works
to match into IOV resources but that is going to be changed by an upcoming
change.
Replace resource_size() check with res->parent check that is the true
dividing line in between whether assign or reassign function should be used
for the resource.
Link: https://lore.kernel.org/r/20241216175632.4175-24-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
PCI resource fitting is somewhat hard to track because it performs many
actions without logging them. In the case inside
__assign_resources_sorted(), the resources are released before resource
assignment is going to be retried in a different order. That is just one
level of retries the resource fitting performs overall so tracking it
through repeated assignments or failures of a resource gets messy rather
quickly.
Simply announce the release explicitly using pci_dbg() so it is clear what
is going on with each resource.
Link: https://lore.kernel.org/r/20241216175632.4175-23-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Add pci_dbg() to note that an assignment failure was for an optional
resource and reword existing message about resource resize to say the
change was optional.
Link: https://lore.kernel.org/r/20241216175632.4175-22-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Add a dummy list to always have a non-NULL realloc head in
__assign_resources_sorted() as it allows only checking list_empty().
In future, it would be good to ensure all callers provide a valid
realloc_head but that is relatively complex to do in practice and not
necessary for the subsequent optional resource handling fix.
Link: https://lore.kernel.org/r/20241216175632.4175-21-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
pci_enable_resources() checks if device's io and mem resources are all
assigned and disallows enable if any resource failed to assign (*) but
makes an exception for the case of disabled extension ROM. There are other
optional resources, however.
Add pci_resource_is_optional() and use it instead of
pci_resource_is_disabled_rom() to cover also IOV resources that are also
optional as per pbus_size_mem().
As there will be more users of pci_resource_is_optional() inside
setup-bus.c in changes coming up after this one, the function is placed
there.
(*) In practice, resource fitting code calls reset_resource() for any
resource it fails to assign which clears resource's ->flags causing
pci_enable_resources() to never detect failed resource assignments.
This seems undesirable internal logic inconsistency, effectively
reset_resource() prevents pci_enable_resources() from functioning as
intended. This is one step of many that will be needed towards removing
reset_resource().
Link: https://lore.kernel.org/r/20241216175632.4175-20-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Resource fitting needs to restore the saved dev resources in a few places.
Add a restore_dev_resource() helper for that.
Link: https://lore.kernel.org/r/20241216175632.4175-19-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Commit a4ac9fea01 ("PCI : Calculate right add_size") removed including
min_align into new_size in pci_reassign_resource() which is the correct
thing to do. However, it also added a snakeoil comment that the resource
would already be aligned with min_align which is incorrect.
A resource that is assigned earlier is aligned with the old alignment, NOT
with the new requested alignment (min_align) until later deep within the
reassignment callchain. Thus, remove the incorrect comment.
Link: https://lore.kernel.org/r/20241216175632.4175-18-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Cc: Yinghai Lu <yinghai@kernel.org>
pci_assign_unassigned_root_bus_resources() and
pci_assign_unassigned_bridge_resources() have a loop that may perform
several rounds to assign resources. The code to prepare for the next round
is identical.
Consolidate the code that prepares for the next assignment round into
pci_prepare_next_assign_round().
Link: https://lore.kernel.org/r/20241216175632.4175-17-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
pci_assign_unassigned_root_bus_resources() and
pci_assign_unassigned_bridge_resources() contain ad hoc loops using
backwards goto and gotos out of the loop. Replace them with while loops
and break statements.
While reindenting the loop bodies, add braces & remove parenthesis.
Link: https://lore.kernel.org/r/20241216175632.4175-15-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Reduce level of call nesting by calling pdev_sort_resources() directly
and by moving the tests done inside __dev_sort_resources() into
pdev_resources_assignable() helper.
Link: https://lore.kernel.org/r/20241216175632.4175-14-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
All return paths want to free head list in __assign_resources_sorted(), so
add a label and use goto.
Link: https://lore.kernel.org/r/20241216175632.4175-13-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Many PCI resource allocation related functions process struct
pci_dev_resource items which hold the struct pci_dev and resource pointers.
Reduce the number of lines that need indirection by adding 'dev' and 'res'
local variable to hold the pointers.
Link: https://lore.kernel.org/r/20241216175632.4175-12-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
A few places in PCI code, mainly in setup-bus.c, need to reverse lookup the
index of a resource in pci_dev's resource array. Create pci_resource_num()
helper to avoid repeating the pointer arithmetic trick used to calculate
the index.
Link: https://lore.kernel.org/r/20241216175632.4175-11-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Instead of chaining logic inside if () condition so that multiple lines are
required, make !resource_size() a separate check and use continue.
Link: https://lore.kernel.org/r/20241216175632.4175-10-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
There are multiple places where special handling is required for IOV
resources.
Extract the identification of IOV resources to pci_resource_is_iov() and
drop a few ifdefs.
Link: https://lore.kernel.org/r/20241216175632.4175-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
A few sites that could use resource_set_range/size() in setup-bus.c were
not picked up earlier due to them no matching the usual pattern. Convert
them now.
These are more cases similar to 783602c920 ("PCI: Use
resource_set_{range,size}() helpers").
Link: https://lore.kernel.org/r/20241216175632.4175-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: add 783602c920 history]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Convert literals in setup-bus.c to SZ_* defines that make the size more
human readable.
As the code is now self-explanatory, eliminate comments about the size.
Link: https://lore.kernel.org/r/20241216175632.4175-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Commit 903534fa7d ("PCI: Fix resource double counting on remove &
rescan") fixed double counting of mem resources because of old_size being
applied too early.
Fix a similar counting bug on the io resource side.
Link: https://lore.kernel.org/r/20241216175632.4175-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Commit 566f1dd528 ("PCI: Relax bridge window tail sizing rules")
relaxed the bridge window requirements for non-optional size (size0)
but pbus_size_mem() also handles optional sizes (IOV resources) using
size1. This can manifest, e.g., as a failure to resize a BAR back to
its original size after it was first shrunk when device has a VF BAR
resource because the bridge window (size1) is enlarged beyond what is
strictly required to fit the downstream resources.
Allow using relaxed bridge window tail sizing rules also with the optional
resources (size1) so that the remove/realloc cycle during BAR resize
(smaller and back to the original size) does not fail unexpectedly due to
increase in bridge window size demand.
Also move add_align calculation to more logical place next to size1
assignment as they are strongly related to each other.
Link: https://lore.kernel.org/r/20241216175632.4175-5-ilpo.jarvinen@linux.intel.com
Fixes: 566f1dd528 ("PCI: Relax bridge window tail sizing rules")
Reported-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
In pbus_size_io() and pbus_size_mem(), a complex ?: operation is performed
to set size1. Decompose this so it's easier to read.
In the case of pbus_size_mem(), simply initializing size1 to zero ensures
the size1 checks work as expected.
Link: https://lore.kernel.org/r/20241216175632.4175-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Commit 566f1dd528 ("PCI: Relax bridge window tail sizing rules")
relaxed bridge window tail alignment rule for the non-optional part
(size0, no add_size/add_align). The required alignment given for
pbus_upstream_space_available(), however, was add_align which relates
only to size1 alignment.
As pbus_upstream_space_available() only selects between normal and relaxed
tail alignment of the bridge window, the different alignment only makes
relaxed tail alignment to be used more often than what was intended, which
should be harmless because relaxed tail alignment itself should work in all
cases.
For consistency, change pbus_upstream_space_available() call to use
min_align which is the alignment that is going to be used for the bridge
window in the case where size0 sized allocation is attempted.
Link: https://lore.kernel.org/r/20241216175632.4175-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
Commit 566f1dd528 ("PCI: Relax bridge window tail sizing rules")
relaxed bridge window tail alignment rule for the non-optional part
(size0, no add_size/add_align). The change, however, also overwrote
add_align, which is only related to case where optional size1 related
entry is added into realloc head.
Correct this by removing the add_align overwrite.
Link: https://lore.kernel.org/r/20241216175632.4175-2-ilpo.jarvinen@linux.intel.com
Fixes: 566f1dd528 ("PCI: Relax bridge window tail sizing rules")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiaochun Lee <lixc17@lenovo.com>
7180c1d086 ("PCI: Distribute available resources for root buses, too")
breaks BAR assignment on some devices:
pci 0006:03:00.0: BAR 0 [mem 0x6300c0000000-0x6300c1ffffff 64bit pref]: assigned
pci 0006:03:00.1: BAR 0 [mem 0x6300c2000000-0x6300c3ffffff 64bit pref]: assigned
pci 0006:03:00.2: BAR 0 [mem size 0x00800000 64bit pref]: can't assign; no space
pci 0006:03:00.0: VF BAR 0 [mem size 0x02000000 64bit pref]: can't assign; no space
pci 0006:03:00.1: VF BAR 0 [mem size 0x02000000 64bit pref]: can't assign; no space
The apertures of domain 0006 before 7180c1d086:
6300c0000000-63ffffffffff : PCI Bus 0006:00
6300c0000000-6300c9ffffff : PCI Bus 0006:01
6300c0000000-6300c9ffffff : PCI Bus 0006:02 # 160MB
6300c0000000-6300c8ffffff : PCI Bus 0006:03 # 144MB
6300c0000000-6300c1ffffff : 0006:03:00.0 # 32MB
6300c2000000-6300c3ffffff : 0006:03:00.1 # 32MB
6300c4000000-6300c47fffff : 0006:03:00.2 # 8MB
6300c4800000-6300c67fffff : 0006:03:00.0 # 32MB
6300c6800000-6300c87fffff : 0006:03:00.1 # 32MB
6300c9000000-6300c9bfffff : PCI Bus 0006:04 # 12MB
6300c9000000-6300c9bfffff : PCI Bus 0006:05 # 12MB
6300c9000000-6300c91fffff : PCI Bus 0006:06 # 2MB
6300c9200000-6300c93fffff : PCI Bus 0006:07 # 2MB
6300c9400000-6300c95fffff : PCI Bus 0006:08 # 2MB
6300c9600000-6300c97fffff : PCI Bus 0006:09 # 2MB
After 7180c1d086:
6300c0000000-63ffffffffff : PCI Bus 0006:00
6300c0000000-6300c9ffffff : PCI Bus 0006:01
6300c0000000-6300c9ffffff : PCI Bus 0006:02 # 160MB
6300c0000000-6300c43fffff : PCI Bus 0006:03 # 68MB
6300c0000000-6300c1ffffff : 0006:03:00.0 # 32MB
6300c2000000-6300c3ffffff : 0006:03:00.1 # 32MB
--- no space --- : 0006:03:00.2 # 8MB
--- no space --- : 0006:03:00.0 # 32MB
--- no space --- : 0006:03:00.1 # 32MB
6300c4400000-6300c4dfffff : PCI Bus 0006:04 # 10MB
6300c4400000-6300c4dfffff : PCI Bus 0006:05 # 10MB
6300c4400000-6300c45fffff : PCI Bus 0006:06 # 2MB
6300c4600000-6300c47fffff : PCI Bus 0006:07 # 2MB
6300c4800000-6300c49fffff : PCI Bus 0006:08 # 2MB
6300c4a00000-6300c4bfffff : PCI Bus 0006:09 # 2MB
We can see that the window to 0006:03 gets shrunken too much and 0006:04
eats away the window for 0006:03:00.2.
The offending commit distributes the upstream bridge's resources multiple
times to every downstream bridge, hence makes the aperture smaller than
desired because calculation of io_per_b, mmio_per_b and mmio_pref_per_b
becomes incorrect.
Instead, distribute downstream bridges' own resources to resolve the issue.
Link: https://lore.kernel.org/r/20241204022457.51322-1-kaihengf@nvidia.com
Fixes: 7180c1d086 ("PCI: Distribute available resources for root buses, too")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219540
Signed-off-by: Kai-Heng Feng <kaihengf@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Carol Soto <csoto@nvidia.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Chris Chiu <chris.chiu@canonical.com>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmev0oAUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vxeNBAAunByLPVxbteqIXJ6IZHz1956SDfo
batHJodeNCxeVYpjLca+1asqZ75hply3pOK+DUKyNUyEqkXfQDvSZCBfo70uA9ur
eSeaZxBoNS7VnOvmw5w0kEWd2Sx0gEkIPuxegympOfTiWaN8bGoryPHAuGnO0Exz
YTIv+TtLAag96OFswQGvSZyh8AfCg5QXl6vZ0W7Ex+O24o/LJ9sO9gALkhFXoc2+
tdKBJSOQ3dfEVa0S6btNxsY5nsy7xp3CxLYqQTvT2kES0xUwK7QrafOdl0kEaVDB
6JRkFhKaK5R6WDz5d4LnU0mzSrBc17cQD+C6StUd4dzQdzyuiP4X70R+kMiu71ff
XMSBPSbLcP1iQ50O3IdkbV5OVnn7ap3LPP2v/PYcmoYNc3i81hvZap5RDaEnJ/ej
xI+bKullZG787jl+qnweNsu9jar9HWCJOGwMCZIKiXoU8fJdsI+b+53FNxFqqWAR
4DAsu9nGwlkoEFHaDFKeoG/qBrW65UAeIetUoh+dpQ19OaD7vUuv6Uk4aiwbDFx3
jGNBOS1Cwx3aIhLNrg3wxSmajFHaPlI+yElS+PcP/J9cV1YDXV7U/ZKaYTVwU0TZ
l3TY72q3/ckP7+9NaxExO6ow59cN1XNncBkAcOEoSCfFIFnSmvxC8v6Vpwc2ZNQN
o3N9euTROFouZeA=
=HYty
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.14-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Update a BUILD_BUG_ON() usage that works on current compilers, but
breaks compilation on gcc 5.3.1 (Alex Williamson)
- Avoid use of FLR for Mediatek MT7922 WiFi; the device previously
worked after a long timeout and fallback to SBR, but after a recent
RRS change it doesn't work at all after FLR (Bjorn Helgaas)
* tag 'pci-v6.14-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: Avoid FLR for Mediatek MT7922 WiFi
PCI: Fix BUILD_BUG_ON usage for old gcc
The Mediatek MT7922 WiFi device advertises FLR support, but it apparently
does not work, and all subsequent config reads return ~0:
pci 0000:01:00.0: [14c3:0616] type 00 class 0x028000 PCIe Endpoint
pciback 0000:01:00.0: not ready 65535ms after FLR; giving up
After an FLR, pci_dev_wait() waits for the device to become ready. Prior
to d591f6804e ("PCI: Wait for device readiness with Configuration RRS"),
it polls PCI_COMMAND until it is something other that PCI_POSSIBLE_ERROR
(~0). If it times out, pci_dev_wait() returns -ENOTTY and
__pci_reset_function_locked() tries the next available reset method.
Typically this is Secondary Bus Reset, which does work, so the MT7922 is
eventually usable.
After d591f6804e, if Configuration Request Retry Status Software
Visibility (RRS SV) is enabled, pci_dev_wait() polls PCI_VENDOR_ID until it
is something other than the special 0x0001 Vendor ID that indicates a
completion with RRS status.
When RRS SV is enabled, reads of PCI_VENDOR_ID should return either 0x0001,
i.e., the config read was completed with RRS, or a valid Vendor ID. On the
MT7922, it seems that all config reads after FLR return ~0 indefinitely.
When pci_dev_wait() reads PCI_VENDOR_ID and gets 0xffff, it assumes that's
a valid Vendor ID and the device is now ready, so it returns with success.
After pci_dev_wait() returns success, we restore config space and continue.
Since the MT7922 is not actually ready after the FLR, the restore fails and
the device is unusable.
We considered changing pci_dev_wait() to continue polling if a
PCI_VENDOR_ID read returns either 0x0001 or 0xffff. This "works" as it did
before d591f6804e, although we have to wait for the timeout and then fall
back to SBR. But it doesn't work for SR-IOV VFs, which *always* return
0xffff as the Vendor ID.
Mark Mediatek MT7922 WiFi devices to avoid the use of FLR completely. This
will cause fallback to another reset method, such as SBR.
Link: https://lore.kernel.org/r/20250212193516.88741-1-helgaas@kernel.org
Fixes: d591f6804e ("PCI: Wait for device readiness with Configuration RRS")
Link: https://github.com/QubesOS/qubes-issues/issues/9689#issuecomment-2582927149
Link: https://lore.kernel.org/r/Z4pHll_6GX7OUBzQ@mail-itl
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Cc: stable@vger.kernel.org
As reported in the below link, it seems older versions of gcc cannot
determine that the howmany variable is known for all callers. Include
a test so that newer compilers can enforce this sanity check and older
compilers can still work. Add __always_inline attribute to give the
compiler an even better chance to know the inputs.
Link: https://lore.kernel.org/r/20250212185337.293023-1-alex.williamson@redhat.com
Fixes: 4453f36086 ("PCI: Batch BAR sizing operations")
Reported-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lore.kernel.org/all/20250209154512.GA18688@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Oleg Nesterov <oleg@redhat.com>
Tested-by: Mitchell Augustin <mitchell.augustin@canonical.com>
When we reenable TPH after changing a Steering Tag value, we need the
actual TPH Requester Enable value, not the ST Mode (which only happens to
work out by chance for non-extended TPH in interrupt vector mode).
Link: https://lore.kernel.org/r/13118098116d7bce07aa20b8c52e28c7d1847246.1738759933.git.robin.murphy@arm.com
Fixes: d2e8a34876 ("PCI/TPH: Add Steering Tag support")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wei Huang <wei.huang2@amd.com>
Commit 1db806ec06 ("PCI/ASPM: Save parent L1SS config in
pci_save_aspm_l1ss_state()") aimed to perform L1SS config save for both the
Upstream Port and its upstream bridge when handling an Upstream Port, which
matches what the L1SS restore side does. However, parent->state_saved can
be set true at an earlier time when the upstream bridge saved other parts
of its state. Then later when attempting to save the L1SS config while
handling the Upstream Port, parent->state_saved is true in
pci_save_aspm_l1ss_state() resulting in early return and skipping saving
bridge's L1SS config because it is assumed to be already saved. Later on
restore, junk is written into L1SS config which causes issues with some
devices.
Remove parent->state_saved check and unconditionally save L1SS config also
for the upstream bridge from an Upstream Port which ought to be harmless
from correctness point of view. With the Upstream Port check now present,
saving the L1SS config more than once for the bridge is no longer a problem
(unlike when the parent->state_saved check got introduced into the fix
during its development).
Link: https://lore.kernel.org/r/20250131152913.2507-1-ilpo.jarvinen@linux.intel.com
Fixes: 1db806ec06 ("PCI/ASPM: Save parent L1SS config in pci_save_aspm_l1ss_state()")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219731
Reported-by: Niklāvs Koļesņikovs <pinkflames.linux@gmail.com>
Reported by: Rafael J. Wysocki <rafael@kernel.org>
Closes: https://lore.kernel.org/r/CAJZ5v0iKmynOQ5vKSQbg1J_FmavwZE-nRONovOZ0mpMVauheWg@mail.gmail.com
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://lore.kernel.org/r/d7246feb-4f3f-4d0c-bb64-89566b170671@molgen.mpg.de
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Niklāvs Koļesņikovs <pinkflames.linux@gmail.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> # Dell XPS 13 9360
pcim_intx() tries to restore the INTx bit at removal via devres, but there
is a chance that it restores a wrong value.
Because the value to be restored is blindly assumed to be the negative of
the enable argument, when a driver calls pcim_intx() unnecessarily for the
already enabled state, it'll restore to the disabled state in turn. That
is, the function assumes the case like:
// INTx == 1
pcim_intx(pdev, 0); // old INTx value assumed to be 1 -> correct
but it might be like the following, too:
// INTx == 0
pcim_intx(pdev, 0); // old INTx value assumed to be 1 -> wrong
Also, when a driver calls pcim_intx() multiple times with different enable
argument values, the last one will win no matter what value it is. This
can lead to inconsistency, e.g.
// INTx == 1
pcim_intx(pdev, 0); // OK
...
pcim_intx(pdev, 1); // now old INTx wrongly assumed to be 0
This patch addresses those inconsistencies by saving the original INTx
state at the first pcim_intx() call. For that, get_or_create_intx_devres()
is folded into pcim_intx() caller side; it allows us to simply check the
already allocated devres and record the original INTx along with the
devres_alloc() call.
Link: https://lore.kernel.org/r/20241031134300.10296-1-tiwai@suse.de
Fixes: 25216afc9d ("PCI: Add managed pcim_intx()")
Link: https://lore.kernel.org/87v7xk2ps5.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Philipp Stanner <pstanner@redhat.com>
Cc: stable@vger.kernel.org # v6.11+
-----BEGIN PGP SIGNATURE-----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=O62O
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Batch sizing of multiple BARs while memory decoding is disabled
instead of disabling/enabling decoding for each BAR individually;
this optimizes virtualized environments where toggling decoding
enable is expensive (Alex Williamson)
- Add host bridge .enable_device() and .disable_device() hooks for
bridges that need to configure things like Requester ID to StreamID
mapping when enabling devices (Frank Li)
- Extend struct pci_ecam_ops with .enable_device() and
.disable_device() hooks so drivers that use pci_host_common_probe()
instead of their own .probe() have a way to set the
.enable_device() callbacks (Marc Zyngier)
- Drop 'No bus range found' message so we don't complain when DTs
don't specify the default 'bus-range = <0x00 0xff>' (Bjorn Helgaas)
- Rename the drivers/pci/of_property.c struct of_pci_range to
of_pci_range_entry to avoid confusion with the global of_pci_range
in include/linux/of_address.h (Bjorn Helgaas)
Driver binding:
- Update resource request API documentation to encourage callers to
supply a driver name when requesting resources (Philipp Stanner)
- Export pci_intx_unmanaged() and pcim_intx() (always managed) so
callers of pci_intx() (which is sometimes managed) can explicitly
choose the one they need (Philipp Stanner)
- Convert drivers from pci_intx() to always-managed pcim_intx() or
never-managed pci_intx_unmanaged(): amd_sfh, ata (ahci, ata_piix,
pata_rdc, sata_sil24, sata_sis, sata_uli, sata_vsc), bnx2x, bna,
ntb, qtnfmac, rtsx, tifm_7xx1, vfio, xen-pciback (Philipp Stanner)
- Remove pci_intx_unmanaged() since pci_intx() is now always
unmanaged and pcim_intx() is always managed (Philipp Stanner)
Error handling:
- Unexport pcie_read_tlp_log() to encourage drivers to use PCI core
logging rather than building their own (Ilpo Järvinen)
- Move TLP Log handling to its own file (Ilpo Järvinen)
- Store number of supported End-End TLP Prefixes always so we can
read the correct number of DWORDs from the TLP Prefix Log (Ilpo
Järvinen)
- Read TLP Prefixes in addition to the Header Log in
pcie_read_tlp_log() (Ilpo Järvinen)
- Add pcie_print_tlp_log() to consolidate printing of TLP Header and
Prefix Log (Ilpo Järvinen)
- Quirk the Intel Raptor Lake-P PIO log size to accommodate vendor
BIOSes that don't configure it correctly (Takashi Iwai)
ASPM:
- Save parent L1 PM Substates config so when we restore it along with
an endpoint's config, the parent info isn't junk (Jian-Hong Pan)
Power management:
- Avoid D3 for Root Ports on TUXEDO Sirius Gen1 with old BIOS because
the system can't wake up from suspend (Werner Sembach)
Endpoint framework:
- Destroy the EPC device in devm_pci_epc_destroy(), which previously
didn't call devres_release() (Zijun Hu)
- Finish virtual EP removal in pci_epf_remove_vepf(), which
previously caused a subsequent pci_epf_add_vepf() to fail with
-EBUSY (Zijun Hu)
- Write BAR_MASK before iATU registers in pci_epc_set_bar() so we
don't depend on the BAR_MASK reset value being larger than the
requested BAR size (Niklas Cassel)
- Prevent changing BAR size/flags in pci_epc_set_bar() to prevent
reads from bypassing the iATU if we reduced the BAR size (Niklas
Cassel)
- Verify address alignment when programming iATU so we don't attempt
to write bits that are read-only because of the BAR size, which
could lead to directing accesses to the wrong address (Niklas
Cassel)
- Implement artpec6 pci_epc_features so we can rely on all drivers
supporting it so we can use it in EPC core code (Niklas Cassel)
- Check for BARs of fixed size to prevent endpoint drivers from
trying to change their size (Niklas Cassel)
- Verify that requested BAR size is a power of two when endpoint
driver sets the BAR (Niklas Cassel)
Endpoint framework tests:
- Clear pci-epf-test dma_chan_rx, not dma_chan_tx, after freeing
dma_chan_rx (Mohamed Khalfella)
- Correct the DMA MEMCPY test so it doesn't fail if the Endpoint
supports both DMA_PRIVATE and DMA_MEMCPY (Manivannan Sadhasivam)
- Add pci-epf-test and pci_endpoint_test support for capabilities
(Niklas Cassel)
- Add Endpoint test for consecutive BARs (Niklas Cassel)
- Remove redundant comparison from Endpoint BAR test because a > 1MB
BAR can always be exactly covered by iterating with a 1MB buffer
(Hans Zhang)
- Move and convert PCI Endpoint tests from tools/pci to Kselftests
(Manivannan Sadhasivam)
Apple PCIe controller driver:
- Convert StreamID mapping configuration from a bus notifier to the
.enable_device() and .disable_device() callbacks (Marc Zyngier)
Freescale i.MX6 PCIe controller driver:
- Add Requester ID to StreamID mapping configuration when enabling
devices (Frank Li)
- Use DWC core suspend/resume functions for imx6 (Frank Li)
- Add suspend/resume support for i.MX8MQ, i.MX8Q, and i.MX95 (Richard
Zhu)
- Add DT compatible string 'fsl,imx8q-pcie-ep' and driver support for
i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) Endpoints (Frank
Li)
- Add DT binding for optional i.MX95 Refclk and driver support to
enable it if the platform hasn't enabled it (Richard Zhu)
- Configure PHY based on controller being in Root Complex or Endpoint
mode (Frank Li)
- Rely on dbi2 and iATU base addresses from DT via
dw_pcie_get_resources() instead of hardcoding them (Richard Zhu)
- Deassert apps_reset in imx_pcie_deassert_core_reset() since it is
asserted in imx_pcie_assert_core_reset() (Richard Zhu)
- Add missing reference clock enable or disable logic for IMX6SX,
IMX7D, IMX8MM (Richard Zhu)
- Remove redundant imx7d_pcie_init_phy() since
imx7d_pcie_enable_ref_clk() does the same thing (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead
of syscon_regmap_lookup_by_phandle() followed by
of_property_read_u32_array() (Krzysztof Kozlowski)
Marvell MVEBU PCIe controller driver:
- Add MODULE_DEVICE_TABLE() to enable module autoloading (Liao Chen)
MediaTek PCIe Gen3 controller driver:
- Use clk_bulk_prepare_enable() instead of separate
clk_bulk_prepare() and clk_bulk_enable() (Lorenzo Bianconi)
- Rearrange reset assert/deassert so they're both done in the
*_power_up() callbacks (Lorenzo Bianconi)
- Document that Airoha EN7581 requires PHY init and power-on before
PHY reset deassert, unlike other MediaTek Gen3 controllers (Lorenzo
Bianconi)
- Move Airoha EN7581 post-reset delay from the en7581 clock .enable()
method to mtk_pcie_en7581_power_up() (Lorenzo Bianconi)
- Sleep instead of delay during Airoha EN7581 power-up, since this is
a non-atomic context (Lorenzo Bianconi)
- Skip PERST# assertion on Airoha EN7581 during probe and
suspend/resume to avoid a hardware defect (Lorenzo Bianconi)
- Enable async probe to reduce system startup time (Douglas Anderson)
Microchip PolarFlare PCIe controller driver:
- Set up the inbound address translation based on whether the
platform allows coherent or non-coherent DMA (Daire McNamara)
- Update DT binding such that platforms are DMA-coherent by default
and must specify 'dma-noncoherent' if needed (Conor Dooley)
Mobiveil PCIe controller driver:
- Convert mobiveil-pcie.txt to YAML and update 'interrupt-names'
and 'reg-names' (Frank Li)
Qualcomm PCIe controller driver:
- Add DT SM8550 and SM8650 optional 'global' interrupt for link
events (Neil Armstrong)
- Add DT 'compatible' strings for IPQ5424 PCIe controller (Manikanta
Mylavarapu)
- If 'global' IRQ is supported for detection of Link Up events, tell
DWC core not to wait for link up (Krishna chaitanya chundru)
Renesas R-Car PCIe controller driver:
- Avoid passing stack buffer as resource name (King Dix)
Rockchip PCIe controller driver:
- Simplify clock and reset handling by using bulk interfaces (Anand
Moon)
- Pass typed rockchip_pcie (not void) pointer to
rockchip_pcie_disable_clocks() (Anand Moon)
- Return -ENOMEM, not success, when pci_epc_mem_alloc_addr() fails
(Dan Carpenter)
Rockchip DesignWare PCIe controller driver:
- Use dll_link_up IRQ to detect Link Up and enumerate devices so
users don't have to manually rescan (Niklas Cassel)
- Tell DWC core not to wait for link up since the 'sys' interrupt is
required and detects Link Up events (Niklas Cassel)
Synopsys DesignWare PCIe controller driver:
- Don't wait for link up in DWC core if driver can detect Link Up
event (Krishna chaitanya chundru)
- Update ICC and OPP votes after Link Up events (Krishna chaitanya
chundru)
- Always stop link in dw_pcie_suspend_noirq(), which is required at
least for i.MX8QM to re-establish link on resume (Richard Zhu)
- Drop racy and unnecessary LTSSM state check before sending
PME_TURN_OFF message in dw_pcie_suspend_noirq() (Richard Zhu)
- Add struct of_pci_range.parent_bus_addr for devices that need their
immediate parent bus address, not the CPU address, e.g., to program
an internal Address Translation Unit (iATU) (Frank Li)
TI DRA7xx PCIe controller driver:
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
syscon_regmap_lookup_by_phandle() followed by
of_parse_phandle_with_fixed_args() or of_property_read_u32_index()
(Krzysztof Kozlowski)
Xilinx Versal CPM PCIe controller driver:
- Add DT binding and driver support for Xilinx Versal CPM5
(Thippeswamy Havalige)
MicroSemi Switchtec management driver:
- Add Microchip PCI100X device IDs (Rakesh Babu Saladi)
Miscellaneous:
- Move reset related sysfs code from pci.c to pci-sysfs.c where other
similar code lives (Ilpo Järvinen)
- Simplify reset_method_store() memory management by using __free()
instead of explicit kfree() cleanup (Ilpo Järvinen)
- Constify struct bin_attribute for sysfs, VPD, P2PDMA, and the IBM
ACPI hotplug driver (Thomas Weißschuh)
- Remove redundant PCI_VSEC_HDR and PCI_VSEC_HDR_LEN_SHIFT (Dongdong
Zhang)
- Correct documentation of the 'config_acs=' kernel parameter
(Akihiko Odaki)"
* tag 'pci-v6.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (111 commits)
PCI: Batch BAR sizing operations
dt-bindings: PCI: microchip,pcie-host: Allow dma-noncoherent
PCI: microchip: Set inbound address translation for coherent or non-coherent mode
Documentation: Fix pci=config_acs= example
PCI: Remove redundant PCI_VSEC_HDR and PCI_VSEC_HDR_LEN_SHIFT
PCI: Don't include 'pm_wakeup.h' directly
selftests: pci_endpoint: Migrate to Kselftest framework
selftests: Move PCI Endpoint tests from tools/pci to Kselftests
misc: pci_endpoint_test: Fix IOCTL return value
dt-bindings: PCI: qcom: Document the IPQ5424 PCIe controller
dt-bindings: PCI: qcom,pcie-sm8550: Document 'global' interrupt
dt-bindings: PCI: mobiveil: Convert mobiveil-pcie.txt to YAML
PCI: switchtec: Add Microchip PCI100X device IDs
misc: pci_endpoint_test: Remove redundant 'remainder' test
misc: pci_endpoint_test: Add consecutive BAR test
misc: pci_endpoint_test: Add support for capabilities
PCI: endpoint: pci-epf-test: Add support for capabilities
PCI: endpoint: pci-epf-test: Fix check for DMA MEMCPY test
PCI: endpoint: pci-epf-test: Set dma_chan_rx pointer to NULL on error
PCI: dwc: Simplify config resource lookup
...
- Add DT binding and driver support for Xilinx Versal CPM5 (Thippeswamy
Havalige)
* pci/controller/xilinx-cpm:
PCI: xilinx-cpm: Add support for Versal CPM5 Root Port Controller 1
dt-bindings: PCI: xilinx-cpm: Add compatible string for CPM5 host1
- Set up the inbound address translation based on whether the platform
allows coherent or non-coherent DMA (Daire McNamara)
- Update DT binding such that platforms are DMA-coherent by default and
must specify 'dma-noncoherent' if needed (Conor Dooley)
* pci/controller/microchip:
dt-bindings: PCI: microchip,pcie-host: Allow dma-noncoherent
PCI: microchip: Set inbound address translation for coherent or non-coherent mode
- Use clk_bulk_prepare_enable() instead of separate clk_bulk_prepare() and
clk_bulk_enable() (Lorenzo Bianconi)
- Rearrange reset assert/deassert so they're both done in the *_power_up()
callbacks (Lorenzo Bianconi)
- Document that Airoha EN7581 requires PHY init and power-on before PHY
reset deassert, unlike other MediaTek Gen3 controllers (Lorenzo Bianconi)
- Move Airoha EN7581 post-reset delay from the en7581 clock .enable()
method to mtk_pcie_en7581_power_up() (Lorenzo Bianconi)
- Sleep instead of delay during Airoha EN7581 power-up, since this is a
non-atomic context (Lorenzo Bianconi)
- Skip PERST# assertion on Airoha EN7581 during probe and suspend/resume to
avoid a hardware defect (Lorenzo Bianconi)
- Enable async probe to reduce system startup time (Douglas Anderson)
* pci/controller/mediatek:
PCI: mediatek-gen3: Enable async probe by default
PCI: mediatek-gen3: Avoid PCIe resetting via PERST# for Airoha EN7581 SoC
PCI: mediatek-gen3: Rely on msleep() in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Move reset delay in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Add comment about initialization order in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Move reset/assert callbacks in .power_up()
PCI: mediatek-gen3: Rely on clk_bulk_prepare_enable() in mtk_pcie_en7581_power_up()
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
syscon_regmap_lookup_by_phandle() followed by
of_property_read_u32_array() (Krzysztof Kozlowski)
* pci/controller/layerscape:
PCI: layerscape: Use syscon_regmap_lookup_by_phandle_args
- Add DT compatible string 'fsl,imx8q-pcie-ep' and driver support for
i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) Endpoints (Frank Li)
- Add DT binding for optional i.MX95 Refclk and driver support to enable it
if the platform hasn't enabled it (Richard Zhu)
- Configure PHY based on controller being in Root Complex or Endpoint mode
(Frank Li)
- Rely on dbi2 and iATU base addresses from DT via dw_pcie_get_resources()
instead of hardcoding them in imx6 (Richard Zhu)
- Skip controller_id computation for i.MX7D since it only has one
controller (Richard Zhu)
- Deassert apps_reset in imx_pcie_deassert_core_reset() since it is
asserted in imx_pcie_assert_core_reset() (Richard Zhu)
- Add missing reference clock enable or disable logic for IMX6SX, IMX7D,
IMX8MM (Richard Zhu)
- Remove redundant imx7d_pcie_init_phy() since imx7d_pcie_enable_ref_clk()
does the same thing (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Clean up comments and whitespace
PCI: imx6: Remove surplus imx7d_pcie_init_phy() function
PCI: imx6: Add missing reference clock disable logic
PCI: imx6: Deassert apps_reset in imx_pcie_deassert_core_reset()
PCI: imx6: Skip controller_id generation logic for i.MX7D
PCI: imx6: Fetch dbi2 and iATU base addesses from DT
PCI: imx6: Configure PHY based on Root Complex or Endpoint mode
PCI: imx6: Add Refclk for i.MX95 PCIe
dt-bindings: PCI: fsl,imx6q-pcie: Add Refclk for i.MX95 RC
PCI: imx6: Add i.MX8Q PCIe Endpoint (EP) support
dt-bindings: PCI: fsl,imx6q-pcie-ep: Add compatible string fsl,imx8q-pcie-ep
# Conflicts:
# drivers/pci/controller/dwc/pci-imx6.c
- Fix potential string truncation in dw_pcie_edma_irq_verify() (Niklas
Cassel)
- Don't wait for link up in DWC core if driver can detect Link Up event
(Krishna chaitanya chundru)
- If qcom 'global' IRQ is supported for detection of Link Up events, tell
DWC core not to wait for link up (Krishna chaitanya chundru)
- Update ICC and OPP votes after Link Up events (Krishna chaitanya chundru)
- Use dw-rockchip dll_link_up IRQ to detect Link Up and enumerate devices
so users don't have to manually rescan (Niklas Cassel)
- In dw-rockchip, the 'sys' interrupt is required and detects Link Up
events, so tell DWC core not to wait for link up (Niklas Cassel)
- Always stop link in dw_pcie_suspend_noirq(), which is required at least
for i.MX8QM to re-establish link on resume (Richard Zhu)
- Drop racy and unnecessary LTSSM state check before sending PME_TURN_OFF
message in dw_pcie_suspend_noirq() (Richard Zhu)
- Add stubs for dw_pcie_suspend_noirq() dw_pcie_resume_noirq() when
CONFIG_PCIE_DW_HOST is not defined so drivers don't need #ifdefs (Bjorn
Helgaas)
- Use DWC core suspend/resume functions for imx6 (Frank Li)
- Add imx6 suspend/resume support for i.MX8MQ, i.MX8Q, and i.MX95 (Richard
Zhu)
- Add struct of_pci_range.parent_bus_addr for devices that need their
immediate parent bus address, not the CPU address, e.g., to program an
internal Address Translation Unit (iATU) (Frank Li)
* pci/controller/dwc:
PCI: dwc: Simplify config resource lookup
of: address: Add parent_bus_addr to struct of_pci_range
PCI: imx6: Add i.MX8MQ, i.MX8Q and i.MX95 PM support
PCI: imx6: Use DWC common suspend resume method
PCI: dwc: Add dw_pcie_suspend_noirq(), dw_pcie_resume_noirq() stubs for !CONFIG_PCIE_DW_HOST
PCI: dwc: Remove LTSSM state test in dw_pcie_suspend_noirq()
PCI: dwc: Always stop link in the dw_pcie_suspend_noirq
PCI: dw-rockchip: Don't wait for link since we can detect Link Up
PCI: dw-rockchip: Enumerate endpoints based on dll_link_up IRQ
PCI: qcom: Update ICC and OPP values after Link Up event
PCI: qcom: Don't wait for link if we can detect Link Up
PCI: dwc: Don't wait for link up if driver can detect Link Up event
PCI: dwc: Fix potential truncation in dw_pcie_edma_irq_verify()
# Conflicts:
# drivers/pci/controller/dwc/pci-imx6.c
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
syscon_regmap_lookup_by_phandle() followed by
of_parse_phandle_with_fixed_args() or of_property_read_u32_index()
(Krzysztof Kozlowski)
* pci/controller/dra7xx:
PCI: dra7xx: Use syscon_regmap_lookup_by_phandle_args
- Add host bridge .enable_device() and .disable_device() hooks for bridges
that need to configure things like Requester ID to StreamID mapping when
enabling devices (Frank Li)
- Add imx6 Requester ID to StreamID mapping configuration when enabling
devices (Frank Li)
- Extend struct pci_ecam_ops with .enable_device() and .disable_device()
hooks so drivers that use pci_host_common_probe() instead of their own
.probe() have a way to set the .enable_device() callbacks (Marc Zyngier)
- Convert pcie-apple StreamID mapping configuration from a bus notifier to
the .enable_device() and .disable_device() callbacks (Marc Zyngier)
* pci/controller/iommu-map:
PCI: apple: Convert to {en,dis}able_device() callbacks
PCI: host-generic: Allow {en,dis}able_device() to be provided via pci_ecam_ops
PCI: imx6: Add IOMMU and ITS MSI support for i.MX95
PCI: Add enable_device() and disable_device() callbacks for bridges
- Clear pci-epf-test dma_chan_rx, not dma_chan_tx, after freeing
dma_chan_rx (Mohamed Khalfella)
- Correct the DMA MEMCPY test so it doesn't fail if the Endpoint supports
both DMA_PRIVATE and DMA_MEMCPY (Manivannan Sadhasivam)
- Add pci-epf-test and pci_endpoint_test support for capabilities (Niklas
Cassel)
- Add Endpoint test for consecutive BARs (Niklas Cassel)
- Remove redundant comparison from Endpoint BAR test because a > 1MB BAR
can always be exactly covered by iterating with a 1MB buffer (Hans Zhang)
- Correct the PCI Endpoint test IOCTL return value (Manivannan Sadhasivam)
- Move PCI Endpoint tests from tools/pci to Kselftests (Manivannan
Sadhasivam)
- Convert PCI Endpoint tests to the Kselftest framework (Manivannan
Sadhasivam)
* pci/endpoint-test:
selftests: pci_endpoint: Migrate to Kselftest framework
selftests: Move PCI Endpoint tests from tools/pci to Kselftests
misc: pci_endpoint_test: Fix IOCTL return value
misc: pci_endpoint_test: Remove redundant 'remainder' test
misc: pci_endpoint_test: Add consecutive BAR test
misc: pci_endpoint_test: Add support for capabilities
PCI: endpoint: pci-epf-test: Add support for capabilities
PCI: endpoint: pci-epf-test: Fix check for DMA MEMCPY test
PCI: endpoint: pci-epf-test: Set dma_chan_rx pointer to NULL on error
- Destroy the EPC device in devm_pci_epc_destroy(), which previously didn't
call devres_release() (Zijun Hu)
- Simplify pci_epc_get() with class_find_device_by_name() (Zijun Hu)
- Finish virtual EP removal in pci_epf_remove_vepf(), which previously
caused a subsequent pci_epf_add_vepf() to fail with -EBUSY (Zijun Hu)
- Write BAR_MASK before iATU registers in pci_epc_set_bar() so we don't
depend on the BAR_MASK reset value being larger than the requested BAR
size (Niklas Cassel)
- Prevent changing BAR size/flags in pci_epc_set_bar() to prevent reads
from bypassing the iATU if we reduced the BAR size (Niklas Cassel)
- Verify address alignment when programming iATU so we don't attempt to
write bits that are read-only because of the BAR size, which could lead
to directing accesses to the wrong address (Niklas Cassel)
- Implement artpec6 pci_epc_features so we can rely on all drivers
supporting it so we can use it in EPC core code (Niklas Cassel)
- Check for BARs of fixed size to prevent endpoint drivers from trying to
change their size (Niklas Cassel)
- Verify that requested BAR size is a power of two when endpoint driver
sets the BAR (Niklas Cassel)
* pci/endpoint:
PCI: endpoint: Verify that requested BAR size is a power of two
PCI: endpoint: Add size check for fixed size BARs in pci_epc_set_bar()
PCI: artpec6: Implement dw_pcie_ep operation get_features
PCI: dwc: ep: Add 'address' alignment to 'size' check in dw_pcie_prog_ep_inbound_atu()
PCI: dwc: ep: Prevent changing BAR size/flags in pci_epc_set_bar()
PCI: dwc: ep: Write BAR_MASK before iATU registers in pci_epc_set_bar()
PCI: endpoint: Finish virtual EP removal in pci_epf_remove_vepf()
PCI: endpoint: Simplify pci_epc_get()
PCI: endpoint: Destroy the EPC device in devm_pci_epc_destroy()
PCI: endpoint: Replace magic number '6' by PCI_STD_NUM_BARS
- Move reset related sysfs code from pci.c to pci-sysfs.c where other
similar code lives (Ilpo Järvinen)
- Simplify reset_method_store() memory management by using __free() instead
of explicit kfree() cleanup (Ilpo Järvinen)
- Drop unnecessary zero initializer (Ilpo Järvinen)
* pci/pci-sysfs:
PCI/sysfs: Remove unnecessary zero in initializer
PCI/sysfs: Use __free() in reset_method_store()
PCI/sysfs: Move reset related sysfs code to correct file
- Unexport of_pci_parse_bus_range() since it's only used in of.c (Bjorn
Helgaas)
- Drop 'No bus range found' message so we don't complain when DTs don't
specify the default 'bus-range = <0x00 0xff>' (Bjorn Helgaas)
- Simplify devm_of_pci_get_host_bridge_resources() interface by dropping
parameters that are always the same default values (Bjorn Helgaas)
- Update comment reference to of_pci_get_host_bridge_resources(), which no
longer exists (Bjorn Helgaas)
- Rename the drivers/pci/of_property.c struct of_pci_range to
of_pci_range_entry to avoid confusion with the global of_pci_range in
include/linux/of_address.h (Bjorn Helgaas)
* pci/of:
PCI: of_property: Rename struct of_pci_range to of_pci_range_entry
sparc/PCI: Update reference to devm_of_pci_get_host_bridge_resources()
PCI: of: Simplify devm_of_pci_get_host_bridge_resources() interface
PCI: of: Drop 'No bus range found' message
PCI: Unexport of_pci_parse_bus_range()
- Unexport pcie_read_tlp_log() to encourage drivers to use PCI core logging
rather than building their own (Ilpo Järvinen)
- Move TLP Log handling to its own file (Ilpo Järvinen)
- Add #defines for TLP Header/Prefix log sizes (Ilpo Järvinen)
- Store number of supported End-End TLP Prefixes always so we can read the
correct number of DWORDs from the TLP Prefix Log (Ilpo Järvinen)
- Read TLP Prefixes in addition to the Header Log in pcie_read_tlp_log()
(Ilpo Järvinen)
- Add pcie_print_tlp_log() to consolidate printing of TLP Header and Prefix
Log (Ilpo Järvinen)
* pci/err:
PCI: Add pcie_print_tlp_log() to print TLP Header and Prefix Log
PCI: Add TLP Prefix reading to pcie_read_tlp_log()
PCI: Store number of supported End-End TLP Prefixes
PCI: Use unsigned int i in pcie_read_tlp_log()
PCI: Use same names in pcie_read_tlp_log() prototype and definition
PCI: Add defines for TLP Header/Prefix log sizes
PCI: Move TLP Log handling to its own file
PCI: Don't expose pcie_read_tlp_log() outside PCI subsystem
- Batch sizing of multiple BARs while memory decoding is disabled instead
of disabling/enabling decoding for each BAR individually; this optimizes
virtualized environments where toggling decoding enable is expensive
(Alex Williamson)
* pci/enumeration:
PCI: Batch BAR sizing operations
- Quirk the Intel Raptor Lake-P PIO log size to accommodate vendor BIOSes
that don't configure it correctly (Takashi Iwai)
* pci/dpc:
PCI/DPC: Quirk PIO log size for Intel Raptor Lake-P
- Update resource request API documentation to encourage callers to supply
a driver name when requesting resources (Philipp Stanner)
- Export pci_intx_unmanaged() and pcim_intx() (always managed) so callers
of pci_intx() (which is sometimes managed) can explicitly choose the one
they need (Philipp Stanner)
- Convert drivers from pci_intx() to always-managed pcim_intx() or
never-managed pci_intx_unmanaged(): amd_sfh, ata (ahci, ata_piix,
pata_rdc, sata_sil24, sata_sis, sata_uli, sata_vsc), bnx2x, bna, ntb,
qtnfmac, rtsx, tifm_7xx1, vfio, xen-pciback (Philipp Stanner)
- Remove pci_intx_unmanaged() since pci_intx() is now always unmanaged and
pcim_intx() is always managed (Philipp Stanner)
* pci/devres:
PCI: Remove devres from pci_intx()
net/ethernet: Use never-managed version of pci_intx()
HID: amd_sfh: Use always-managed version of pcim_intx()
wifi: qtnfmac: use always-managed version of pcim_intx()
ata: Use always-managed version of pci_intx()
PCI/MSI: Use never-managed version of pci_intx()
vfio/pci: Use never-managed version of pci_intx()
misc: Use never-managed version of pci_intx()
ntb: Use never-managed version of pci_intx()
drivers/xen: Use never-managed version of pci_intx()
PCI: Export pci_intx_unmanaged() and pcim_intx()
PCI: Encourage resource request API users to supply driver name
Toggling memory enable is free on bare metal, but potentially expensive
in virtualized environments as the device MMIO spaces are added and
removed from the VM address space, including DMA mapping of those spaces
through the IOMMU where peer-to-peer is supported. Currently memory
decode is disabled around sizing each individual BAR, even for SR-IOV
BARs while VF Enable is cleared.
This can be better optimized for virtual environments by sizing a set
of BARs at once, stashing the resulting mask into an array, while only
toggling memory enable once. This also naturally improves the SR-IOV
path as the caller becomes responsible for any necessary decode disables
while sizing BARs, therefore SR-IOV BARs are sized relying only on the
VF Enable rather than toggling the PF memory enable in the command
register.
Link: https://lore.kernel.org/r/20250120182202.1878581-1-alex.williamson@redhat.com
Reported-by: Mitchell Augustin <mitchell.augustin@canonical.com>
Link: https://lore.kernel.org/r/CAHTA-uYp07FgM6T1OZQKqAdSA5JrZo0ReNEyZgQZub4mDRrV5w@mail.gmail.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Mitchell Augustin <mitchell.augustin@canonical.com>
Reviewed-by: Mitchell Augustin <mitchell.augustin@canonical.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
drivers, per usual, and then a handful of drivers for other SoCs. Then the
usual pile of cleanups is fairly small data fixes or converting DT bindings to
YAML so they can be validated. No changes to the core framework besides an OF
node refcount bump that never got decremented.
New Drivers:
- 5L35023 variant of Versa 3 clock generator
- Various Qualcomm clk controllers: IPQ CMN PLL, SM6115 LPASS, SM750 global,
tcsr, rpmh, and display. X Plus GPU and global. QCS615 rpmh and MSM8937 and
MSM8940 RPM.
- Qualcomm Pongo and Taycan Alpha PLLs
- Qualcomm IPQ5424 NoC-related interconnect clks
- Renesas RZ/G3E (R9A09G047) SoC clk driver
- SAMA7D65 SoC clk driver
- Samsung Exynos990 SoC clk driver
-----BEGIN PGP SIGNATURE-----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=wK9g
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"A pretty quiet cycle this time around. We have a bunch of new Qualcomm
clk drivers, per usual, and then a handful of drivers for other SoCs.
Then the usual pile of cleanups is fairly small data fixes or
converting DT bindings to YAML so they can be validated.
No changes to the core framework besides an OF node refcount bump that
never got decremented.
New Drivers:
- 5L35023 variant of Versa 3 clock generator
- Various Qualcomm clk controllers: IPQ CMN PLL, SM6115 LPASS, SM750
global, tcsr, rpmh, and display. X Plus GPU and global. QCS615 rpmh
and MSM8937 and MSM8940 RPM.
- Qualcomm Pongo and Taycan Alpha PLLs
- Qualcomm IPQ5424 NoC-related interconnect clks
- Renesas RZ/G3E (R9A09G047) SoC clk driver
- SAMA7D65 SoC clk driver
- Samsung Exynos990 SoC clk driver"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (159 commits)
clk: analogbits: Fix incorrect calculation of vco rate delta
clk: bcm: rpi: Add disp clock
clk: bcm: rpi: Create helper to retrieve private data
clk: bcm: rpi: Enable minimize for all firmware clocks
clk: bcm: rpi: Allow cpufreq driver to also adjust gpu clocks
clk: bcm: rpi: Add ISP to exported clocks
clk: stm32f4: support spread spectrum clock generation
clk: stm32f4: use FIELD helpers to access the PLLCFGR fields
dt-bindings: clock: st,stm32-rcc: support spread spectrum clocking
dt-bindings: clock: convert stm32 rcc bindings to json-schema
clk: Use str_enable_disable-like helpers
clk: clk-loongson2: Fix the number count of clk provider
clk: clk-loongson2: Switch to use devm_clk_hw_register_fixed_rate_parent_data()
clk: starfive: Make _clk_get become a common helper function
clk: en7523: Add clock for eMMC for EN7581
dt-bindings: clock: add ID for eMMC for EN7581
dt-bindings: clock: drop NUM_CLOCKS define for EN7581
clk: en7523: Rework clock handling for different clock numbers
clk: thead: Fix cpu2vp_clk for TH1520 AP_SUBSYS clocks
clk: thead: Add CLK_IGNORE_UNUSED to fix TH1520 boot
...
On Microchip PolarFire SoC the PCIe Root Port can be behind one of three
general purpose Fabric Interface Controller (FIC) buses that encapsulates
an AXI-S bus. Depending on which FIC(s) the Root Port is connected through
to CPU space, and what address translation is done by that FIC, the Root
Port driver's inbound address translation may vary.
For all current supported designs and all future expected designs, inbound
address translation done by a FIC on PolarFire SoC varies depending on
whether PolarFire SoC is operating in coherent DMA mode or noncoherent DMA
mode.
The setup of the outbound address translation tables in the Root Port
driver only needs to handle these two cases.
Setup the inbound address translation tables to one of two address
translations, depending on whether the Root Port is being used with
coherent DMA or noncoherent DMA.
Link: https://lore.kernel.org/r/20241011140043.1250030-3-daire.mcnamara@microchip.com
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
[bhelgaas: adapt for ac7f53b7e7 ("PCI: microchip: Add support for using
either Root Port 1 or 2")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
The header clearly states that it does not want to be included directly,
only via 'device.h'. The 'platform_device.h' works equally well.
Thus, remove the direct inclusion.
Link: https://lore.kernel.org/r/20241118072917.3853-12-wsa+renesas@sang-engineering.com
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Consolidation of the machine_kexec_mask_interrupts() by providing a
generic implementation and replacing the copy & pasta orgy in the
relevant architectures.
- Prevent unconditional operations on interrupt chips during kexec
shutdown, which can trigger warnings in certain cases when the
underlying interrupt has been shut down before.
- Make the enforcement of interrupt handling in interrupt context
unconditionally available, so that it actually works for non x86
related interrupt chips. The earlier enablement for ARM GIC chips set
the required chip flag, but did not notice that the check was hidden
behind a config switch which is not selected by ARM[64].
- Decrapify the handling of deferred interrupt affinity setting. Some
interrupt chips require that affinity changes are made from the context
of handling an interrupt to avoid certain race conditions. For x86 this
was the default, but with interrupt remapping this requirement was
lifted and a flag was introduced which tells the core code that
affinity changes can be done in any context. Unrestricted affinity
changes are the default for the majority of interrupt chips. RISCV has
the requirement to add the deferred mode to one of it's interrupt
controllers, but with the original implementation this would require to
add the any context flag to all other RISC-V interrupt chips. That's
backwards, so reverse the logic and require that chips, which need the
deferred mode have to be marked accordingly. That avoids chasing the
'sane' chips and marking them.
- Add multi-node support to the Loongarch AVEC interrupt controller
driver.
- The usual tiny cleanups, fixes and improvements all over the place.
-----BEGIN PGP SIGNATURE-----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=q4rj
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2025-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt subsystem updates from Thomas Gleixner:
- Consolidate the machine_kexec_mask_interrupts() by providing a
generic implementation and replacing the copy & pasta orgy in the
relevant architectures.
- Prevent unconditional operations on interrupt chips during kexec
shutdown, which can trigger warnings in certain cases when the
underlying interrupt has been shut down before.
- Make the enforcement of interrupt handling in interrupt context
unconditionally available, so that it actually works for non x86
related interrupt chips. The earlier enablement for ARM GIC chips set
the required chip flag, but did not notice that the check was hidden
behind a config switch which is not selected by ARM[64].
- Decrapify the handling of deferred interrupt affinity setting.
Some interrupt chips require that affinity changes are made from the
context of handling an interrupt to avoid certain race conditions.
For x86 this was the default, but with interrupt remapping this
requirement was lifted and a flag was introduced which tells the core
code that affinity changes can be done in any context. Unrestricted
affinity changes are the default for the majority of interrupt chips.
RISCV has the requirement to add the deferred mode to one of it's
interrupt controllers, but with the original implementation this
would require to add the any context flag to all other RISC-V
interrupt chips. That's backwards, so reverse the logic and require
that chips, which need the deferred mode have to be marked
accordingly. That avoids chasing the 'sane' chips and marking them.
- Add multi-node support to the Loongarch AVEC interrupt controller
driver.
- The usual tiny cleanups, fixes and improvements all over the place.
* tag 'irq-core-2025-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/generic_chip: Export irq_gc_mask_disable_and_ack_set()
genirq/timings: Add kernel-doc for a function parameter
genirq: Remove IRQ_MOVE_PCNTXT and related code
x86/apic: Convert to IRQCHIP_MOVE_DEFERRED
genirq: Provide IRQCHIP_MOVE_DEFERRED
hexagon: Remove GENERIC_PENDING_IRQ leftover
ARC: Remove GENERIC_PENDING_IRQ
genirq: Remove handle_enforce_irqctx() wrapper
genirq: Make handle_enforce_irqctx() unconditionally available
irqchip/loongarch-avec: Add multi-nodes topology support
irqchip/ts4800: Replace seq_printf() by seq_puts()
irqchip/ti-sci-inta : Add module build support
irqchip/ti-sci-intr: Add module build support
irqchip/irq-brcmstb-l2: Replace brcmstb_l2_mask_and_ack() by generic function
irqchip: keystone: Use syscon_regmap_lookup_by_phandle_args
genirq/kexec: Prevent redundant IRQ masking by checking state before shutdown
kexec: Consolidate machine_kexec_mask_interrupts() implementation
genirq: Reuse irq_thread_fn() for forced thread case
genirq: Move irq_thread_fn() further up in the code
Add Microchip parts to the Device ID table so the driver supports PCI100x
devices.
Add a new macro to quirk the Microchip Switchtec PCI100x parts to allow DMA
access via NTB to work when the IOMMU is turned on.
PCI100x family has 6 variants; each variant is designed for different
application usages, different port counts and lane counts:
PCI1001 has 1 x4 upstream port and 3 x4 downstream ports
PCI1002 has 1 x4 upstream port and 4 x2 downstream ports
PCI1003 has 2 x4 upstream ports, 2 x2 upstream ports, and 2 x2
downstream ports
PCI1004 has 4 x4 upstream ports
PCI1005 has 1 x4 upstream port and 6 x2 downstream ports
PCI1006 has 6 x2 upstream ports and 2 x2 downstream ports
[Historical note: these parts use PCI_VENDOR_ID_EFAR (0x1055), from EFAR
Microsystems, which was acquired in 1996 by Standard Microsystems Corp,
which was acquired by Microchip Technology in 2012. The PCI-SIG confirms
that Vendor ID 0x1055 is assigned to Microchip even though it's not
visible via https://pcisig.com/membership/member-companies]
Link: https://lore.kernel.org/r/20250120095524.243103-1-Saladi.Rakeshbabu@microchip.com
Signed-off-by: Rakesh Babu Saladi <Saladi.Rakeshbabu@microchip.com>
[bhelgaas: Vendor ID history]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Logan Gunthorpe <logang@deltatee.com>
The test BAR is on the EP side is allocated using pci_epf_alloc_space(),
which allocates the backing memory using dma_alloc_coherent(), which will
return zeroed memory regardless of __GFP_ZERO was set or not.
This means that running a new version of pci-endpoint-test.c (host side)
with an old version of pci-epf-test.c (EP side) will not see any
capabilities being set (as intended), so this is backwards compatible.
Additionally, the EP side always allocates at least 128 bytes for the test
BAR (excluding the MSI-X table), this means that adding another register at
offset 0x30 is still within the 128 available bytes.
For now, we only add the CAP_UNALIGNED_ACCESS capability.
Set CAP_UNALIGNED_ACCESS if the EPC driver can handle any address (because
it implements the .align_addr callback).
Link: https://lore.kernel.org/r/20241203063851.695733-5-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Currently, if DMA MEMCPY test is requested by the host, and if the endpoint
DMA controller supports DMA_PRIVATE, the test will fail. This is not
correct since there is no check for DMA_MEMCPY capability and the DMA
controller can support both DMA_PRIVATE and DMA_MEMCPY.
Fix the check and also reword the error message.
Link: https://lore.kernel.org/r/20250116171650.33585-2-manivannan.sadhasivam@linaro.org
Fixes: 8353813c88 ("PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities")
Reported-by: Niklas Cassel <cassel@kernel.org>
Closes: https://lore.kernel.org/linux-pci/Z3QtEihbiKIGogWA@ryzen
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
-----BEGIN PGP SIGNATURE-----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=EXYs
-----END PGP SIGNATURE-----
Merge tag 'for-6.14/block-20250118' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe pull requests via Keith:
- Target support for PCI-Endpoint transport (Damien)
- TCP IO queue spreading fixes (Sagi, Chaitanya)
- Target handling for "limited retry" flags (Guixen)
- Poll type fix (Yongsoo)
- Xarray storage error handling (Keisuke)
- Host memory buffer free size fix on error (Francis)
- MD pull requests via Song:
- Reintroduce md-linear (Yu Kuai)
- md-bitmap refactor and fix (Yu Kuai)
- Replace kmap_atomic with kmap_local_page (David Reaver)
- Quite a few queue freeze and debugfs deadlock fixes
Ming introduced lockdep support for this in the 6.13 kernel, and it
has (unsurprisingly) uncovered quite a few issues
- Use const attributes for IO schedulers
- Remove bio ioprio wrappers
- Fixes for stacked device atomic write support
- Refactor queue affinity helpers, in preparation for better supporting
isolated CPUs
- Cleanups of loop O_DIRECT handling
- Cleanup of BLK_MQ_F_* flags
- Add rotational support for null_blk
- Various fixes and cleanups
* tag 'for-6.14/block-20250118' of git://git.kernel.dk/linux: (106 commits)
block: Don't trim an atomic write
block: Add common atomic writes enable flag
md/md-linear: Fix a NULL vs IS_ERR() bug in linear_add()
block: limit disk max sectors to (LLONG_MAX >> 9)
block: Change blk_stack_atomic_writes_limits() unit_min check
block: Ensure start sector is aligned for stacking atomic writes
blk-mq: Move more error handling into blk_mq_submit_bio()
block: Reorder the request allocation code in blk_mq_submit_bio()
nvme: fix bogus kzalloc() return check in nvme_init_effects_log()
md/md-bitmap: move bitmap_{start, end}write to md upper layer
md/raid5: implement pers->bitmap_sector()
md: add a new callback pers->bitmap_sector()
md/md-bitmap: remove the last parameter for bimtap_ops->endwrite()
md/md-bitmap: factor behind write counters out from bitmap_{start/end}write()
md: Replace deprecated kmap_atomic() with kmap_local_page()
md: reintroduce md-linear
partitions: ldm: remove the initial kernel-doc notation
blk-cgroup: rwstat: fix kernel-doc warnings in header file
blk-cgroup: fix kernel-doc warnings in header file
nbd: fix partial sending
...
If platform_get_resource_byname("config") fails, return error immediately
and unindent the normal path. No functional change intended.
Link: https://lore.kernel.org/r/20250117235119.712043-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Previously there were two definitions of struct of_pci_range: one in
include/linux/of_address.h and another local to drivers/pci/of_property.c.
Rename the local struct of_pci_range to of_pci_range_entry to avoid
confusion.
Link: https://lore.kernel.org/r/20250117161037.643953-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lizhi Hou <lizhi.hou@amd.com>
Call common DWC suspend/resume function. Use DWC common iATU method to
send out PME_TURN_OFF message.
In old DWC implementations, PCIE_ATU_INHIBIT_PAYLOAD in iATU Ctrl2 register
is reserved, so the generic DWC implementation of sending the PME_Turn_Off
message using a dummy MMIO write cannot be used. Use the previous method to
kick off PME_TURN_OFF message for these platforms.
The System Reset Control (SRC) interface is used to toggle 'turnoff_reset'
to send PME_TURN_OFF and since the DWC implementation is used, it is not
needed now.
Replace the imx_pcie_stop_link() and imx_pcie_host_exit() by
dw_pcie_suspend_noirq() in imx_pcie_suspend_noirq().
Since dw_pcie_suspend_noirq() already does these, see below call stack:
dw_pcie_suspend_noirq()
dw_pcie_stop_link()
imx_pcie_stop_link()
pci->pp.ops->deinit()
imx_pcie_host_exit()
Replace the imx_pcie_host_init(), dw_pcie_setup_rc() and
imx_pcie_start_link() by dw_pcie_resume_noirq() in imx_pcie_resume_noirq().
Since dw_pcie_resume_noirq() already does these, see below call stack:
dw_pcie_resume_noirq()
pci->pp.ops->init()
imx_pcie_host_init()
dw_pcie_setup_rc()
dw_pcie_start_link()
imx_pcie_start_link(;
Link: https://lore.kernel.org/r/20241126075702.4099164-9-hongxing.zhu@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously pcie-designware.h declared dw_pcie_suspend_noirq() and
dw_pcie_resume_noirq() unconditionally, even though they were only
implemented when CONFIG_PCIE_DW_HOST was defined.
Add no-op stubs for them when CONFIG_PCIE_DW_HOST is not defined so
drivers that support both Root Complex and Endpoint modes don't need
Link: https://lore.kernel.org/r/20250117213810.GA656803@bhelgaas
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_intx() is a hybrid function which can sometimes be managed through
devres. This hybrid nature is undesirable.
Since all users of pci_intx() have by now been ported either to
always-managed pcim_intx() or never-managed pci_intx_unmanaged(), the
devres functionality can be removed from pci_intx().
Consequently, pci_intx_unmanaged() is now redundant, because pci_intx()
itself is now unmanaged.
Remove the devres functionality from pci_intx(). Have all users of
pci_intx_unmanaged() call pci_intx(). Remove pci_intx_unmanaged().
Link: https://lore.kernel.org/r/20241209130632.132074-13-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
pci_intx() is a hybrid function which can sometimes be managed through
devres. To remove this hybrid nature from pci_intx(), it is necessary to
port users to either an always-managed or a never-managed version.
MSI sets up its own separate devres callback implicitly in
pcim_setup_msi_release(). This callback ultimately uses pci_intx(), which
is problematic since the callback runs on driver detach.
That problem has last been described here:
https://lore.kernel.org/all/ee44ea7ac760e73edad3f20b30b4d2fff66c1a85.camel@redhat.com/
Replace the call to pci_intx() with one to the never-managed version
pci_intx_unmanaged().
Link: https://lore.kernel.org/r/20241209130632.132074-9-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
pci_intx() is a hybrid function which sometimes performs devres operations,
depending on whether pcim_enable_device() has been used to enable the
pci_dev. This sometimes-managed nature of the function is problematic.
Notably, it causes the function to allocate under some circumstances which
makes it unusable from interrupt context.
Export pcim_intx() (which is always managed) and rename __pcim_intx()
(which is never managed) to pci_intx_unmanaged() and export it as well.
Then all callers of pci_intx() can be ported to the version they need,
depending whether they use pci_enable_device() or pcim_enable_device().
Link: https://lore.kernel.org/r/20241209130632.132074-3-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
It's safe to send PME_TURN_OFF message regardless of whether the link is up
or down, so don't test the LTSSM state before sending the PME_TURN_OFF
message.
Only print an error message when the LTSSM is not in DETECT or POLL. There
shouldn't be an error when no Endpoint is connected at all.
Link: https://lore.kernel.org/r/20241210081557.163555-3-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
On the i.MX8QM, PCIe link can't be re-established again in
dw_pcie_resume_noirq(), if the LTSSM_EN bit is not cleared
properly in dw_pcie_suspend_noirq().
So, add dw_pcie_stop_link() to dw_pcie_suspend_noirq() to fix
this issue and to align the suspend/resume functions since there
is dw_pcie_start_link() in dw_pcie_resume_noirq() already.
Fixes: 4774faf854 ("PCI: dwc: Implement generic suspend/resume functionality")
Link: https://lore.kernel.org/r/20241210081557.163555-2-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The Root Complex specific device tree binding for pcie-dw-rockchip has the
'sys' interrupt marked as required.
The driver requests the 'sys' IRQ unconditionally, and errors out if not
provided.
Thus, we can unconditionally set 'use_linkup_irq', so dw_pcie_host_init()
doesn't wait for the link to come up.
This will skip the wait for link up (since the bus will be enumerated once
the link up IRQ is triggered), which reduces the bootup time.
Link: https://lore.kernel.org/r/20250113-rockchip-no-wait-v1-1-25417f37b92f@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Most boards using the pcie-dw-rockchip PCIe controller lack standard
hotplug support.
Thus, when an endpoint is attached to the SoC, users have to rescan the bus
manually to enumerate the device. This can be avoided by using the
'dll_link_up' interrupt in the combined system interrupt 'sys'.
Once the 'dll_link_up' IRQ is received, the bus underneath the host bridge
is scanned to enumerate PCIe endpoint devices.
This implements the same functionality that was implemented in the DWC
based pcie-qcom driver in 4581403f67 ("PCI: qcom: Enumerate endpoints
based on Link up event in 'global_irq' interrupt").
The Root Complex specific device tree binding for pcie-dw-rockchip already
has the 'sys' interrupt marked as required, so there is no need to update
the device tree binding. This also means that we can request the 'sys' IRQ
unconditionally.
Link: https://lore.kernel.org/r/20241127145041.3531400-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log, squash Pei Xiao's redundant dev_err() fix from
https://lore.kernel.org/r/327718207d3cd72847c079ff9d56eb246744c182.1736126067.git.xiaopei01@kylinos.cn,
squash Niklas's #define change from https://lore.kernel.org/r/20250103095812.2408364-2-cassel@kernel.org]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in
'global_irq' interrupt") added the Link Up-based enumeration support, but
did not update the ICC/OPP vote once link is up. Before that, the update
happened during probe and the endpoints may or may not be enumerated at
that time, so the ICC/OPP vote was not guaranteed to be accurate.
With Link Up-based enumeration support, the driver can request the accurate
vote based on the PCIe link.
Call qcom_pcie_icc_opp_update() in qcom_pcie_global_irq_thread() after
enumerating the endpoints.
Fixes: 4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt")
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-3-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
If we have a 'global' IRQ for Link Up events, we need not wait for the
link to be up during PCI initialization, which reduces startup time.
Check for 'global' IRQ, and if present, set 'use_linkup_irq',
so dw_pcie_host_init() doesn't wait for the link to come up.
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-2-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
If the driver can detect the Link Up event and enumerate downstream devices
at that time, we need not wait here.
Skip waiting for link to come up if the driver supports 'use_linkup_irq'.
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-1-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comment, update commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Increase the size of the string buffer to avoid potential truncation in
dw_pcie_edma_irq_verify().
This fixes the following build warning when compiling with W=1:
drivers/pci/controller/dwc/pcie-designware.c: In function ‘dw_pcie_edma_detect’:
drivers/pci/controller/dwc/pcie-designware.c:989:50: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 3 [-Wformat-truncation=]
989 | snprintf(name, sizeof(name), "dma%d", pci->edma.nr_irqs);
| ^~
Link: https://lore.kernel.org/r/20250104002119.2681246-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Link: https://lore.kernel.org/r/20250112-syscon-phandle-args-pci-v1-1-fcb6ebcc0afc@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
Link: https://lore.kernel.org/r/20250112-syscon-phandle-args-pci-v1-2-fcb6ebcc0afc@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
This function essentially duplicates imx7d_pcie_enable_ref_clk(). So remove
it.
Link: https://lore.kernel.org/r/20241126075702.4099164-8-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Ensure the *_enable_ref_clk() function is symmetric by addressing missing
disable parts on some platforms.
Fixes: d0a75c791f ("PCI: imx6: Factor out ref clock disable to match enable")
Link: https://lore.kernel.org/r/20241126075702.4099164-7-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Since the apps_reset is asserted in imx_pcie_assert_core_reset(), it should
be deasserted in imx_pcie_deassert_core_reset().
Fixes: 9b3fe6796d ("PCI: imx6: Add code to support i.MX7D")
Link: https://lore.kernel.org/r/20241126075702.4099164-6-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
The i.MX7D only has one PCIe controller, so controller_id should always be
0. The previous code is incorrect although yielding the correct result.
Fix by removing "IMX7D" from the switch case branch.
Fixes: 2d8ed461db ("PCI: imx6: Add support for i.MX8MQ")
Link: https://lore.kernel.org/r/20241126075702.4099164-5-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Since dw_pcie_get_resources() gets the dbi2 and iATU base addresses from
DT, remove the code from the imx6 driver that does the same.
Upstream DTSes have not enabled Endpoint function. So nothing is broken for
old upstream DTBs.
Link: https://lore.kernel.org/r/20241126075702.4099164-4-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Pass PHY_MODE_PCIE_EP if the PCI controller operates in Endpoint (EP) mode,
and fix the Root Complex (RC) mode being hardcoded using a drvdata mode
check.
Fixes: 8026f2d8e8 ("PCI: imx6: Call common PHY API to set mode, speed, and submode")
Link: https://lore.kernel.org/r/20241119-pci_fixup_addr-v8-6-c4bfa5193288@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Add "ref" clock to enable Refclk. To avoid breaking DT backwards
compatibility, the i.MX95 "ref" clock is optional. Use
devm_clk_get_optional() to fetch i.MX95 PCIe optional clocks in driver.
If using external clock, "ref" clock should point to external reference.
If using internal clock, CREF_EN in LAST_TO_REG controls reference output,
implemented in drivers/clk/imx/clk-imx95-blk-ctl.c.
Link: https://lore.kernel.org/r/20241126075702.4099164-3-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Add support for the i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) PCIe
Endpoint (EP). On the i.MX8Q platforms, the PCI bus addresses differ
from the CPU addresses. However, the DesignWare (DWC) driver already
handles this in the common code.
Link: https://lore.kernel.org/r/20241119-pci_fixup_addr-v8-7-c4bfa5193288@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add pcie_print_tlp_log() to print TLP Header and Prefix Log. Print End-End
Prefixes only if they are non-zero.
Consolidate the few places which currently print TLP using custom
formatting.
Link: https://lore.kernel.org/r/20250114170840.1633-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
pcie_read_tlp_log() handles only 4 Header Log DWORDs but TLP Prefix Log
(PCIe r6.1 secs 7.8.4.12 & 7.9.14.13) may also be present.
Generalize pcie_read_tlp_log() and struct pcie_tlp_log to also handle TLP
Prefix Log. The relevant registers are formatted identically in AER and DPC
Capability, but has these variations:
a) The offsets of TLP Prefix Log registers vary.
b) DPC RP PIO TLP Prefix Log register can be < 4 DWORDs.
c) AER TLP Prefix Log Present (PCIe r6.1 sec 7.8.4.7) can indicate Prefix
Log is not present.
Therefore callers must pass the offset of the TLP Prefix Log register and
the entire length to pcie_read_tlp_log() to be able to read the correct
number of TLP Prefix DWORDs from the correct offset.
Link: https://lore.kernel.org/r/20250114170840.1633-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: squash ternary fix from
https://lore.kernel.org/r/20250116172019.88116-1-colin.i.king@gmail.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Previously pci_parse_request_of_pci_ranges() supplied the default bus range
to devm_of_pci_get_host_bridge_resources(), but that function is static and
has no other callers, so there's no reason to complicate its interface by
passing the default bus range.
Drop the busno and bus_max parameters and use 0x0 and 0xff directly in
devm_of_pci_get_host_bridge_resources().
Link: https://lore.kernel.org/r/20250113231557.441289-4-helgaas@kernel.org
[bhelgaas: dev_warn() for invalid end of bus-range]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The typical bus range for a host bridge is [bus 00-ff], and
devm_of_pci_get_host_bridge_resources() defaults to that unless DT contains
a "bus-range" property.
devm_of_pci_get_host_bridge_resources() previously emitted a message when
there was no "bus-range" property, but that seems unnecessary for this
common situation. Remove the message.
Link: https://lore.kernel.org/r/20250113231557.441289-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
of_pci_parse_bus_range() is only used in drivers/pci/of.c, so make it
static and unexport it.
Link: https://lore.kernel.org/r/20250113231557.441289-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Now that the core host-bridge infrastructure is able to give us a callback
on each device being added or removed, convert the bus-notifier hack to it.
Link: https://lore.kernel.org/r/20241204150145.800408-3-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In order to let host controller drivers using the host-generic
infrastructure use the {en,dis}able_device() callbacks that can be used to
configure sideband RID mapping hardware, provide these two callbacks as
part of the pci_ecam_ops structure.
Link: https://lore.kernel.org/r/20241204150145.800408-2-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
For the i.MX95, the configuration of a LUT is necessary to convert PCIe
Requester IDs (RIDs) to StreamIDs, which are used by both IOMMU and ITS.
This involves checking msi-map and iommu-map device tree properties to
ensure consistent mapping of Requester IDs to the same StreamIDs.
Subsequently, LUT-related registers are configured. If a msi-map isn't
detected, the platform relies on DWC built-in controller for MSIs that
do not need StreamIDs.
Implement PCI bus callback function to handle enable_device() and
disable_device() operations, setting up the LUT whenever a new PCI
device is enabled.
Known limitations:
- If iommu-map exists in the device tree but the IOMMU controller is
disabled, StreamIDs are programmed into the LUT. However, if a RID
is out of range of the iommu-map, enabling the PCI device would
result in a failure, although the PCI device can work without the
IOMMU.
- If msi-map exists in the device tree but the MSI controller is
disabled, MSIs will not work. The DWC driver skips initializing the
built-in MSI controller, falling back to legacy PCI INTx only.
Link: https://lore.kernel.org/r/20250114-imx95_lut-v9-2-39f58dbed03a@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: fix uninitialized "sid" in imx_pcie_enable_device()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Instead of marking individual interrupts as safe to be migrated in
arbitrary contexts, mark the interrupt chips, which require the interrupt
to be moved in actual interrupt context, with the new IRQCHIP_MOVE_DEFERRED
flag. This makes more sense because this is a per interrupt chip property
and not restricted to individual interrupts.
That flips the logic from the historical opt-out to a opt-in model. This is
simpler to handle for other architectures, which default to unrestricted
affinity setting. It also allows to cleanup the redundant core logic
significantly.
All interrupt chips, which belong to a top-level domain sitting directly on
top of the x86 vector domain are marked accordingly, unless the related
setup code marks the interrupts with IRQ_MOVE_PCNTXT, i.e. XEN.
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/all/20241210103335.563277044@linutronix.de
Refactor rockchip_pcie_disable_clocks() to accept a struct rockchip_pcie
pointer instead of a void pointer thus improving type safety and code
readability by explicitly specifying the expected data type.
Link: https://lore.kernel.org/r/20241202151150.7393-4-linux.amoon@gmail.com
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the driver acquires and asserts/deasserts the resets
individually thereby making the driver complex to read.
This can be simplified by using the reset_control_bulk() APIs.
Use devm_reset_control_bulk_get_exclusive() API to acquire all the resets
and use reset_control_bulk_{assert/deassert}() APIs to assert/deassert them
in bulk.
Following the recommendations in 'Rockchip RK3399 TRM v1.3 Part2':
1. Split the reset controls into two groups as per section '17.5.8.1.1
PCIe as Root Complex'.
2. Deassert the 'Pipe, MGMT Sticky, MGMT, Core' resets in groups as per
section '17.5.8.1.1 PCIe as Root Complex'. This is accomplished using
the reset_control_bulk APIs.
Link: https://lore.kernel.org/r/20241202151150.7393-3-linux.amoon@gmail.com
Co-developed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: squash error handling fix from https://lore.kernel.org/r/7da6ac56-af55-4436-9597-6af24df8122c@stanley.mountain]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Some PCI host bridges require special handling when enabling or
disabling PCI devices. For example, the i.MX95 platform has a lookup
table to map Requester IDs to StreamIDs, which the SMMU and MSI
controller use to identify the source of DMA accesses.
Without this mapping, DMA accesses may target unintended memory, which
would corrupt memory or read the wrong data.
Add a host bridge enable_device() hook the imx6 driver can use to
configure the Requester ID to StreamID mapping. The hardware table isn't
big enough to map all possible Requester IDs, so this hook may fail if
no table space is available. In that case, return failure from
pci_enable_device().
It might make more sense to make pci_set_master() decline to enable bus
mastering and return failure, but it currently doesn't have a way to return
failure.
Link: https://lore.kernel.org/r/20250114-imx95_lut-v9-1-39f58dbed03a@nxp.com
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Apparently the Raptor Lake-P reference firmware configures the PIO log size
correctly, but some vendor BIOSes, including at least ASUSTeK COMPUTER INC.
Zenbook UX3402VA_UX3402VA, do not.
Apply the quirk for Raptor Lake-P. This prevents kernel complaints like:
DPC: RP PIO log size 0 is invalid
and also enables the DPC driver to dump the RP PIO Log registers when DPC
is triggered.
Note that the bug report also mentions 8086:a76e, which has been already
added by 627c6db207 ("PCI/DPC: Quirk PIO log size for Intel Raptor Lake
Root Ports").
Link: https://lore.kernel.org/r/20250102164315.7562-1-tiwai@suse.de
Link: https://bugzilla.suse.com/show_bug.cgi?id=1234623
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Providing empty initializer for an array is enough to set its elements
to zero. Thus, remove the redundant 0 from the initializer.
Link: https://lore.kernel.org/r/20241028174046.1736-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Use __free() from cleanup.h to handle freeing options in
reset_method_store() as it simplifies the code flow.
Link: https://lore.kernel.org/r/20241028174046.1736-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Most PCI sysfs code and structs are in a dedicated file but a few reset
related things remain in pci.c. Move also them to pci-sysfs.c and drop
pci_dev_reset_method_attr_is_visible() as it is 100% duplicate of
pci_dev_reset_attr_is_visible().
Link: https://lore.kernel.org/r/20241028174046.1736-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
eetlp_prefix_path in the struct pci_dev tells if End-End TLP Prefixes
are supported by the path or not, and the value is only calculated if
CONFIG_PCI_PASID is set.
The Max End-End TLP Prefixes field in the Device Capabilities Register 2
also tells how many (1-4) End-End TLP Prefixes are supported (PCIe r6.2 sec
7.5.3.15). The number of supported End-End Prefixes is useful for reading
correct number of DWORDs from TLP Prefix Log register in AER capability
(PCIe r6.2 sec 7.8.4.12).
Replace eetlp_prefix_path with eetlp_prefix_max and determine the number of
supported End-End Prefixes regardless of CONFIG_PCI_PASID so that an
upcoming commit generalizing TLP Prefix Log register reading does not have
to read extra DWORDs for End-End Prefixes that never will be there.
The value stored into eetlp_prefix_max is directly derived from device's
Max End-End TLP Prefixes and does not consider limitations imposed by
bridges or the Root Port beyond supported/not supported flags. This is
intentional for two reasons:
1) PCIe r6.2 spec sections 2.2.10.4 & 6.2.4.4 indicate that a TLP is
malformed only if the number of prefixes exceed the number of Max
End-End TLP Prefixes, which seems to be the case even if the device
could never receive that many prefixes due to smaller maximum imposed
by a bridge or the Root Port. If TLP parsing is later added, this
distinction is significant in interpreting what is logged by the TLP
Prefix Log registers and the value matching to the Malformed TLP
threshold is going to be more useful.
2) TLP Prefix handling happens autonomously on a low layer and the value
in eetlp_prefix_max is not programmed anywhere by the kernel (i.e.,
there is no limiter OS can control to prevent sending more than N TLP
Prefixes).
Link: https://lore.kernel.org/r/20250114170840.1633-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
Loop variable i counting from 0 upwards does not need to be signed so make
it unsigned int.
Link: https://lore.kernel.org/r/20250114170840.1633-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
pcie_read_tlp_log()'s prototype and function signature diverged due to
changes made while applying.
Make the parameters of pcie_read_tlp_log() named identically.
Link: https://lore.kernel.org/r/20250114170840.1633-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
TLP Log is a PCIe feature and is processed only by AER and DPC.
Configwise, DPC depends AER being enabled. In lack of better place, the TLP
Log handling code was initially placed into pci.c but it can be easily
placed in a separate file.
Move TLP Log handling code to its own file under pcie/ subdirectory and
include it only when AER is enabled.
Link: https://lore.kernel.org/r/20250114170840.1633-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
pcie_read_tlp_log() was exposed by the commit 0a5a46a6a6 ("PCI/AER:
Generalize TLP Header Log reading") with the intent that drivers could use
it, but the PCI maintainer later decided that drivers should be encouraged
to use PCI core diagnostic logging of generic AER registers rather than
building their own.
Drivers that currently implement their own diagnostic logging include ixgbe
(ixgbe_io_error_detected()) and iwlwifi (iwl_trans_pcie_dump_regs()).
Remove the unwanted EXPORT of pcie_read_tlp_log() and remove it from
include/linux/aer.h.
Link: https://lore.kernel.org/r/20250114170840.1633-2-ilpo.jarvinen@linux.intel.com
Link: https://lore.kernel.org/all/20240322193011.GA701027@bhelgaas/
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Link: https://lore.kernel.org/r/20240903132311.961646-1-liaochen4@huawei.com
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Currently, the driver acquires clocks and prepare/enable/disable/unprepare
the clocks individually thereby making the driver complex to read.
The driver can be simplified by using the clk_bulk*() APIs.
Use:
- devm_clk_bulk_get_all() API to acquire all the clocks
- clk_bulk_prepare_enable() to prepare/enable clocks
- clk_bulk_disable_unprepare() APIs to disable/unprepare them in bulk
Link: https://lore.kernel.org/r/20241202151150.7393-2-linux.amoon@gmail.com
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
[bhelgaas: squash error handling fix from https://lore.kernel.org/r/20250106153041.55267-1-linux.amoon@gmail.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
When compiling the Rockchip endpoint driver with -W=1, the following
warnings can be seen in the output:
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'perst_irq' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'perst_asserted' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'link_up' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'link_training' not described in 'rockchip_pcie_ep'
Fix these warnings by adding the missing field descriptions in
struct rockchip_pcie_ep kernel-doc comment.
Fixes: a7137cbf6b ("PCI: rockchip-ep: Handle PERST# signal in EP mode")
Fixes: bd6e61df4b ("PCI: rockchip-ep: Improve link training")
Link: https://lore.kernel.org/r/20241216133404.540736-1-dlemoal@kernel.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The rcar_pcie_parse_outbound_ranges() uses the devm_request_mem_region()
macro to request a needed resource. A string variable that lives on the
stack is then used to store a dynamically computed resource name, which
is then passed on as one of the macro arguments. This can lead to
undefined behavior.
Depending on the current contents of the memory, the manifestations of
errors may vary. One possible output may be as follows:
$ cat /proc/iomem
30000000-37ffffff :
38000000-3fffffff :
Sometimes, garbage may appear after the colon.
In very rare cases, if no NULL-terminator is found in memory, the system
might crash because the string iterator will overrun which can lead to
access of unmapped memory above the stack.
Thus, fix this by replacing outbound_name with the name of the previously
requested resource. With the changes applied, the output will be as
follows:
$ cat /proc/iomem
30000000-37ffffff : memory2
38000000-3fffffff : memory3
Fixes: 2a6d0d63d9 ("PCI: rcar: Add endpoint mode support")
Link: https://lore.kernel.org/r/tencent_DBDCC19D60F361119E76919ADAB25EC13C06@qq.com
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: King Dix <kingdix10@qq.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The mediatek-gen3 driver can run its probe routine fairly slow on some
hardware, which adds to the total time it takes for the system start up.
Thus, turn on async mode for the probe to avoid blocking the rest of the
system.
Link: https://lore.kernel.org/r/20241220145205.1.Ibf2563896c3b1fc133bb46d3fc96ad0041763922@changeid
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Airoha EN7581 has a hw bug asserting/releasing PERST# signal causing
occasional PCIe link down issues. In order to overcome the problem,
PERST# signal is not asserted/released during device probe or
suspend/resume phase and the PCIe block is reset using
en7523_reset_assert() and en7581_pci_enable().
Introduce flags field in the mtk_gen3_pcie_pdata struct in order to
specify per-SoC capabilities.
Link: https://lore.kernel.org/r/20250109-pcie-en7581-rst-fix-v4-1-4a45c89fb143@kernel.org
Tested-by: Hui Ma <hui.ma@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Since mtk_pcie_en7581_power_up() runs in non-atomic context, rely on
msleep() routine instead of mdelay().
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-5-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Airoha EN7581 has a hw bug asserting/releasing PCIE_PE_RSTB signal
causing occasional PCIe link down issues. In order to overcome the
problem, PCIe block is reset using REG_PCI_CONTROL (0x88) and
REG_RESET_CONTROL (0x834) registers available in the clock module
running clk_bulk_prepare_enable() in mtk_pcie_en7581_power_up().
In order to make the code more readable, move the wait for the time
needed to complete the PCIe reset from en7581_pci_enable() to
mtk_pcie_en7581_power_up().
Reduce reset timeout from 250ms to the standard PCIE_T_PVPERL_MS value
(100ms) since it has no impact on the driver behavior.
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-4-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Add a comment in mtk_pcie_en7581_power_up() to clarify, unlike the other
MediaTek Gen3 controllers, the Airoha EN7581 requires PHY initialization
and power-on before PHY reset deassert.
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-3-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
In order to make the code more readable, the reset_control_bulk_assert()
function for PHY reset lines is moved to make it pair with
reset_control_bulk_deassert() in mtk_pcie_power_up() and
mtk_pcie_en7581_power_up(). The same change is done for
reset_control_assert() used to assert MAC reset line.
Introduce PCIE_MTK_RESET_TIME_US macro for the time needed to
complete PCIe reset on MediaTek controller.
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-2-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Replace clk_bulk_prepare() and clk_bulk_enable() with
clk_bulk_prepare_enable() in mtk_pcie_en7581_power_up() routine.
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-1-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The interrupt handler for bandwidth notifications, pcie_bwnotif_irq(),
dereferences a "data" pointer.
On unbind, that pointer is set to NULL by pcie_bwnotif_remove(). However
the interrupt handler may still be invoked afterwards and will dereference
that NULL pointer.
That's because the interrupt is requested using a devm_*() helper and the
driver core releases devm_*() resources *after* calling ->remove().
pcie_bwnotif_remove() does clear the Link Bandwidth Management Interrupt
Enable and Link Autonomous Bandwidth Interrupt Enable bits in the Link
Control Register, but that won't prevent execution of pcie_bwnotif_irq():
The interrupt for bandwidth notifications may be shared with AER, DPC,
PME, and hotplug. So pcie_bwnotif_irq() may be executed as long as the
interrupt is requested.
There's a similar race on bind: pcie_bwnotif_probe() requests the
interrupt when the "data" pointer still points to NULL. A NULL pointer
deref may thus likewise occur if AER, DPC, PME or hotplug raise an
interrupt in-between the bandwidth controller's call to devm_request_irq()
and assignment of the "data" pointer.
Drop the devm_*() usage and reorder requesting of the interrupt to fix the
issue.
While at it, drop a stray but harmless no_free_ptr() invocation when
assigning the "data" pointer in pcie_bwnotif_probe().
Ilpo points out that the locking on unbind and bind needs to be symmetric,
so move the call to pcie_bwnotif_disable() inside the critical section
protected by pcie_bwctrl_setspeed_rwsem and pcie_bwctrl_lbms_rwsem.
Evert reports a hang on shutdown of an ASUS ROG Strix SCAR 17 G733PYV.
The issue is no longer reproducible with the present commit.
Evert found that attaching a USB-C monitor prevented the hang. The
machine contains an ASMedia USB 3.2 controller below a hotplug-capable
Root Port. So one possible explanation is that the controller gets
hot-removed on shutdown unless something is connected. And the ensuing
hotplug interrupt occurs exactly when the bandwidth controller is
unregistering. The precise cause could not be determined because the
screen had already turned black when the hang occurred.
Link: https://lore.kernel.org/r/ae2b02c9cfbefff475b6e132b0aa962aaccbd7b2.1736162539.git.lukas@wunner.de
Fixes: 665745f274 ("PCI/bwctrl: Re-add BW notification portdrv as PCIe BW controller")
Reported-by: Evert Vorster <evorster@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219629
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Evert Vorster <evorster@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The helper devm_clk_bulk_get_all_enable() missed to return the number of
clocks stored in the clk_bulk_data table referenced by the clks
argument and, therefore, will be dropped.
Use the newly introduced devm_clk_bulk_get_all_enabled() variant
instead, which is consistent with devm_clk_bulk_get_all() in terms of
the returned value:
> 0 if one or more clocks have been stored
= 0 if there are no clocks
< 0 if an error occurred
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20241217-clk_bulk_ena_fix-v5-2-aafbbb245155@collabora.com
Acked-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
struct bus_type has a new callback for retrieving the IRQ affinity for a
device. Hook this callback up for PCI based devices.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Link: https://lore.kernel.org/r/20241202-refactor-blk-affinity-helpers-v6-2-27211e9c2cd5@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=zLos
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fixes from Krzysztof Wilczyński:
"Two small patches that are important for fixing boot time hang on
Intel JHL7540 'Titan Ridge' platforms equipped with a Thunderbolt
controller.
The boot time issue manifests itself when a PCI Express bandwidth
control is unnecessarily enabled on the Thunderbolt controller
downstream ports, which only supports a link speed of 2.5 GT/s in
accordance with USB4 v2 specification (p. 671, sec. 11.2.1, "PCIe
Physical Layer Logical Sub-block").
As such, there is no need to enable bandwidth control on such
downstream port links, which also works around the issue.
Both patches were tested by the original reporter on the hardware on
which the failure origin golly manifested itself. Both fixes were
proven to resolve the reported boot hang issue, and both patches have
been in linux-next this week with no reported problems"
* tag 'pci-v6.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/bwctrl: Enable only if more than one speed is supported
PCI: Honor Max Link Speed when determining supported speeds
If a PCIe port only supports a single speed, enabling bandwidth control
is pointless: There's no need to monitor autonomous speed changes, nor
can the speed be changed.
Not enabling it saves a small amount of memory and compute resources,
but also fixes a boot hang reported by Niklas: It occurs when enabling
bandwidth control on Downstream Ports of Intel JHL7540 "Titan Ridge 2018"
Thunderbolt controllers. The ports only support 2.5 GT/s in accordance
with USB4 v2 sec 11.2.1, so the present commit works around the issue.
PCIe r6.2 sec 8.2.1 prescribes that:
"A device must support 2.5 GT/s and is not permitted to skip support
for any data rates between 2.5 GT/s and the highest supported rate."
Consequently, bandwidth control is currently only disabled if a port
doesn't support higher speeds than 2.5 GT/s. However the Implementation
Note in PCIe r6.2 sec 7.5.3.18 cautions:
"It is strongly encouraged that software primarily utilize the
Supported Link Speeds Vector instead of the Max Link Speed field,
so that software can determine the exact set of supported speeds on
current and future hardware. This can avoid software being confused
if a future specification defines Links that do not require support
for all slower speeds."
In other words, future revisions of the PCIe Base Spec may allow gaps
in the Supported Link Speeds Vector. To be future-proof, don't just
check whether speeds above 2.5 GT/s are supported, but rather check
whether *more than one* speed is supported.
Fixes: 665745f274 ("PCI/bwctrl: Re-add BW notification portdrv as PCIe BW controller")
Closes: https://lore.kernel.org/r/db8e457fcd155436449b035e8791a8241b0df400.camel@kernel.org
Link: https://lore.kernel.org/r/3564908a9c99fc0d2a292473af7a94ebfc8f5820.1734428762.git.lukas@wunner.de
Reported-by: Niklas Schnelle <niks@kernel.org>
Tested-by: Niklas Schnelle <niks@kernel.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Jonathan Cameron <Jonthan.Cameron@huawei.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The Supported Link Speeds Vector in the Link Capabilities 2 Register
indicates the *supported* link speeds. The Max Link Speed field in the
Link Capabilities Register indicates the *maximum* of those speeds.
pcie_get_supported_speeds() neglects to honor the Max Link Speed field and
will thus incorrectly deem higher speeds as supported. Fix it.
One user-visible issue addressed here is an incorrect value in the sysfs
attribute "max_link_speed".
But the main motivation is a boot hang reported by Niklas: Intel JHL7540
"Titan Ridge 2018" Thunderbolt controllers supports 2.5-8 GT/s speeds,
but indicate 2.5 GT/s as maximum. Ilpo recalls seeing this on more
devices. It can be explained by the controller's Downstream Ports
supporting 8 GT/s if an Endpoint is attached, but limiting to 2.5 GT/s
if the port interfaces to a PCIe Adapter, in accordance with USB4 v2
sec 11.2.1:
"This section defines the functionality of an Internal PCIe Port that
interfaces to a PCIe Adapter. [...]
The Logical sub-block shall update the PCIe configuration registers
with the following characteristics: [...]
Max Link Speed field in the Link Capabilities Register set to 0001b
(data rate of 2.5 GT/s only).
Note: These settings do not represent actual throughput. Throughput
is implementation specific and based on the USB4 Fabric performance."
The present commit is not sufficient on its own to fix Niklas' boot hang,
but it is a prerequisite: A subsequent commit will fix the boot hang by
enabling bandwidth control only if more than one speed is supported.
The GENMASK() macro used herein specifies 0 as lowest bit, even though
the Supported Link Speeds Vector ends at bit 1. This is done on purpose
to avoid a GENMASK(0, 1) macro if Max Link Speed is zero. That macro
would be invalid as the lowest bit is greater than the highest bit.
Ilpo has witnessed a zero Max Link Speed on Root Complex Integrated
Endpoints in particular, so it does occur in practice. (The Link
Capabilities Register is optional on RCiEPs per PCIe r6.2 sec 7.5.3.)
Fixes: d2bd39c045 ("PCI: Store all PCIe Supported Link Speeds")
Closes: https://lore.kernel.org/r/70829798889c6d779ca0f6cd3260a765780d1369.camel@kernel.org
Link: https://lore.kernel.org/r/fe03941e3e1cc42fb9bf4395e302bff53ee2198b.1734428762.git.lukas@wunner.de
Reported-by: Niklas Schnelle <niks@kernel.org>
Tested-by: Niklas Schnelle <niks@kernel.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add support for the Xilinx Versal CPM5 Root Port Controller 1. The key
difference between Controller 0 and Controller 1 lies in the
platform-specific error interrupt bits, which are located at different
register offsets.
To handle these differences, updated variant structure to hold the
following platform-specific details:
- Interrupt status register offset (ir_status)
- Interrupt enable register offset (ir_enable)
- Miscellaneous interrupt values (ir_misc_value)
The driver differentiates between Controller 0 and Controller 1 using the
compatible string in the device tree. This ensures that the appropriate
register offsets are used for each controller, allowing for correct
handling of platform-specific interrupts and initialization.
Link: https://lore.kernel.org/r/20240922061318.2653503-3-thippesw@amd.com
Signed-off-by: Thippeswamy Havalige <thippesw@amd.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
When allocating a BAR using pci_epf_alloc_space(), there are checks that
round up the size to a power of two.
However, there is no check in pci_epc_set_bar() which verifies that the
requested BAR size is a power of two.
Add a power of two check in pci_epc_set_bar(), so that we don't need to
add such a check in each and every PCI endpoint controller driver.
Link: https://lore.kernel.org/r/20241213143301.4158431-14-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
A BAR of type BAR_FIXED has a fixed BAR size (the size cannot be changed).
When using pci_epf_alloc_space() to allocate backing memory for a BAR,
pci_epf_alloc_space() will always set the size to the fixed BAR size if
the BAR type is BAR_FIXED (and will give an error if you the requested size
is larger than the fixed BAR size).
However, some drivers might not call pci_epf_alloc_space() before calling
pci_epc_set_bar(), so add a check in pci_epc_set_bar() to ensure that an
EPF driver cannot set a size different from the fixed BAR size, if the BAR
type is BAR_FIXED.
The pci_epc_function_is_valid() check is removed because this check is now
done by pci_epc_get_features().
Link: https://lore.kernel.org/r/20241213143301.4158431-13-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
All non-DWC EPC drivers implement (struct pci_epc *)->ops->get_features().
All DWC EPC drivers implement (struct dw_pcie_ep *)->ops->get_features(),
except for pcie-artpec6.c.
epc_features has been required in pci-epf-test.c since commit 6613bc2301
("PCI: endpoint: Fix NULL pointer dereference for ->get_features()").
A follow-up commit will make further use of epc_features in EPC core code.
Implement epc_features in the only EPC driver where it is currently not
implemented.
Link: https://lore.kernel.org/r/20241213143301.4158431-12-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
dw_pcie_prog_ep_inbound_atu() is used to program an inbound iATU in
"BAR Match Mode".
A memory address returned by e.g. kmalloc() is guaranteed to have natural
alignment (aligned to the size of the allocation). It is however not
guaranteed that pci_epc_set_bar() (and thus dw_pcie_prog_ep_inbound_atu())
is supplied an address that has natural alignment. (An EPF driver can send
in an arbitrary physical address to pci_epc_set_bar().)
The DWC Databook description for the LWR_TARGET_RW and LWR_TARGET_HW fields
in the IATU_LWR_TARGET_ADDR_OFF_INBOUND_i registers state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
Add a check to ensure that the physical address programmed in the iATU is
aligned to the size of the BAR (BAR_MASK+1), as without this, we can get
hard to debug errors, as we could write to bits that are read-only (without
getting a write error), which could cause the iATU to end up redirecting to
a physical address that is different from the address that we intended.
Link: https://lore.kernel.org/r/20241213143301.4158431-11-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In commit 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update
inbound map address") set_bar() was modified to support dynamically
changing the backing physical address of a BAR that was already configured.
This means that set_bar() can be called twice, without ever calling
clear_bar() (as calling clear_bar() would clear the BAR's PCI address
assigned by the host).
This can only be done if the new BAR size/flags does not differ from the
existing BAR configuration. Add these missing checks.
If we allow set_bar() to set e.g. a new BAR size that differs from the
existing BAR size, the new address translation range will be smaller than
the BAR size already determined by the host, which would mean that a read
past the new BAR size would pass the iATU untranslated, which could allow
the host to read memory not belonging to the new struct pci_epf_bar.
While at it, add comments which clarifies the support for dynamically
changing the physical address of a BAR. (Which was also missing.)
Fixes: 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Link: https://lore.kernel.org/r/20241213143301.4158431-10-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
The "DesignWare Cores PCI Express Controller Register Descriptions,
Version 4.60a", section "1.21.70 IATU_LWR_TARGET_ADDR_OFF_INBOUND_i",
fields LWR_TARGET_RW and LWR_TARGET_HW both state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
If we do not write the BAR_MASK before writing the iATU registers, we are
relying the reset value of the BAR_MASK being larger than the requested
BAR size (which is supplied in the struct pci_epf_bar which is passed to
pci_epc_set_bar()). The reset value of the BAR_MASK is SoC dependent.
Thus, if the struct pci_epf_bar requests a BAR size that is larger than the
reset value of the BAR_MASK, the iATU will try to write to read-only bits,
which will cause the iATU to end up redirecting to a physical address that
is different from the address that was intended.
Thus, we should always write the iATU registers after writing the BAR_MASK.
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20241213143301.4158431-9-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Alexandre observed a warning emitted from pci_msi_setup_msi_irqs() on a
RISCV platform which does not provide PCI/MSI support:
WARNING: CPU: 1 PID: 1 at drivers/pci/msi/msi.h:121 pci_msi_setup_msi_irqs+0x2c/0x32
__pci_enable_msix_range+0x30c/0x596
pci_msi_setup_msi_irqs+0x2c/0x32
pci_alloc_irq_vectors_affinity+0xb8/0xe2
RISCV uses hierarchical interrupt domains and correctly does not implement
the legacy fallback. The warning triggers from the legacy fallback stub.
That warning is bogus as the PCI/MSI layer knows whether a PCI/MSI parent
domain is associated with the device or not. There is a check for MSI-X,
which has a legacy assumption. But that legacy fallback assumption is only
valid when legacy support is enabled, but otherwise the check should simply
return -ENOTSUPP.
Loongarch tripped over the same problem and blindly enabled legacy support
without implementing the legacy fallbacks. There are weak implementations
which return an error, so the problem was papered over.
Correct pci_msi_domain_supports() to evaluate the legacy mode and add
the missing supported check into the MSI enable path to complete it.
Fixes: d2a463b297 ("PCI/MSI: Reject multi-MSI early")
Reported-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/87ed2a8ow5.ffs@tglx
After 17423360a2 ("PCI/ASPM: Save L1 PM Substates Capability for
suspend/resume"), pci_save_aspm_l1ss_state(dev) saves the L1SS state for
"dev", and pci_restore_aspm_l1ss_state(dev) restores the state for both
"dev" and its parent.
The problem is that unless pci_save_state() has been used in some other
path and has already saved the parent L1SS state, we will restore junk to
the parent, which means the L1 Substates likely won't work correctly.
Save the L1SS config for both the device and its parent in
pci_save_aspm_l1ss_state(). When restoring, we need both because L1SS must
be enabled at the parent (the Downstream Port) before being enabled at the
child (the Upstream Port).
Link: https://lore.kernel.org/r/20241115072200.37509-3-jhp@endlessos.org
Fixes: 17423360a2 ("PCI/ASPM: Save L1 PM Substates Capability for suspend/resume")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218394
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
[bhelgaas: parallel save/restore structure, simplify commit log, patch at
https://lore.kernel.org/r/20241212230340.GA3267194@bhelgaas]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org> # Asus B1400CEAE
When removing a virtual Endpoint, pci_epf_remove_vepf() failed to clear
epf_vf->epf_pf, which caused a subsequent pci_epf_add_vepf() to incorrectly
return -EBUSY:
pci_epf_add_vepf(epf_pf, epf_vf) // add
pci_epf_remove_vepf(epf_pf, epf_vf) // remove
pci_epf_add_vepf(epf_pf, epf_vf) // add again, -EBUSY error
Fix by clearing epf_vf->epf_pf in pci_epf_remove_vepf().
Link: https://lore.kernel.org/r/20241210-pci-epc-core_fix-v3-3-4d86dd573e4b@quicinc.com
Fixes: 1cf362e907 ("PCI: endpoint: Add support to add virtual function in endpoint core")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
The devm_pci_epc_destroy() comment says destroys the EPC device, but it
does not actually do that since devres_destroy() does not call
devm_pci_epc_release(), and it also can not fully undo what the API
devm_pci_epc_create() does, so it is faulty.
Fortunately, the faulty API has not been used by current kernel tree. Use
devres_release() instead of devres_destroy() so the EPC device will be
released.
Link: https://lore.kernel.org/r/20241210-pci-epc-core_fix-v3-1-4d86dd573e4b@quicinc.com
Fixes: 5e8cb40338 ("PCI: endpoint: Add EP core layer to enable EP controller and EP functions")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Link: https://lore.kernel.org/r/20241202-sysfs-const-bin_attr-pci-v1-4-c32360f495a7@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PCI region request functions have a @name parameter (sometimes called
"res_name"). It is used in a log message to inform drivers about request
collisions, e.g., when another driver has requested that region already.
This message is only useful when it contains the actual owner of the
region, i.e., which driver requested it. So far, a great many drivers
misuse the @name parameter and just pass pci_name(), which doesn't result
in useful debug information.
Rename "res_name" to "name".
Detail @name's purpose in the docstrings.
Link: https://lore.kernel.org/r/20241203100023.31152-2-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
[bhelgaas: tweak comment wording to include "driver"]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Link: https://lore.kernel.org/r/20241202-sysfs-const-bin_attr-pci-v1-3-c32360f495a7@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Link: https://lore.kernel.org/r/20241202-sysfs-const-bin_attr-pci-v1-2-c32360f495a7@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Link: https://lore.kernel.org/r/20241202-sysfs-const-bin_attr-pci-v1-1-c32360f495a7@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----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=bPnr
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.13-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fix from Bjorn Helgaas:
- When removing a PCI device, only look up and remove a platform device
if there is an associated device node for which there could be a
platform device, to fix a merge window regression (Brian Norris)
* tag 'pci-v6.13-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/pwrctrl: Unregister platform device only if one actually exists
If a PCI device has an associated device_node with power supplies,
pci_bus_add_device() creates platform devices for use by pwrctrl. When the
PCI device is removed, pci_stop_dev() uses of_find_device_by_node() to
locate the related platform device, then unregisters it.
But when we remove a PCI device with no associated device node,
dev_of_node(dev) is NULL, and of_find_device_by_node(NULL) returns the
first device with "dev->of_node == NULL". The result is that we (a)
mistakenly unregister a completely unrelated platform device, leading to
issues like the first trace below, and (b) dereference the NULL pointer
from dev_of_node() when clearing OF_POPULATED, as in the second trace.
Unregister a platform device only if there is one associated with this PCI
device. This resolves issues seen when doing:
# echo 1 > /sys/bus/pci/devices/.../remove
Sample issue from unregistering the wrong platform device:
WARNING: CPU: 0 PID: 5095 at drivers/regulator/core.c:5885 regulator_unregister+0x140/0x160
Call trace:
regulator_unregister+0x140/0x160
devm_rdev_release+0x1c/0x30
release_nodes+0x68/0x100
devres_release_all+0x98/0xf8
device_unbind_cleanup+0x20/0x70
device_release_driver_internal+0x1f4/0x240
device_release_driver+0x20/0x40
bus_remove_device+0xd8/0x170
device_del+0x154/0x380
device_unregister+0x28/0x88
of_device_unregister+0x1c/0x30
pci_stop_bus_device+0x154/0x1b0
pci_stop_and_remove_bus_device_locked+0x28/0x48
remove_store+0xa0/0xb8
dev_attr_store+0x20/0x40
sysfs_kf_write+0x4c/0x68
Later NULL pointer dereference for of_node_clear_flag(NULL, OF_POPULATED):
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000c0
Call trace:
pci_stop_bus_device+0x190/0x1b0
pci_stop_and_remove_bus_device_locked+0x28/0x48
remove_store+0xa0/0xb8
dev_attr_store+0x20/0x40
sysfs_kf_write+0x4c/0x68
Link: https://lore.kernel.org/r/20241126210443.4052876-1-briannorris@chromium.org
Fixes: 681725afb6 ("PCI/pwrctl: Remove pwrctl device without iterating over all children of pwrctl parent")
Reported-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Closes: https://lore.kernel.org/r/1732890621-19656-1-git-send-email-ssengar@linux.microsoft.com
Signed-off-by: Brian Norris <briannorris@chromium.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the 2 simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups that
can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog
As mentioned above, there is 2 merge conflicts with your tree, one is
where the file is removed (easy enough to resolve), the second is a
build time error, that has been found in linux-next and the fix can be
seen here:
https://lore.kernel.org/r/20241107212645.41252436@canb.auug.org.au
Other than that, the changes here have been in linux-next with no other
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ0lEog8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym+0ACgw6wN+LkLVIHWhxTq5DYHQ0QCxY8AoJrRIcKe
78h0+OU3OXhOy8JGz62W
=oI5S
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the two simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups
that can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog"
* tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Fix a potential abuse of seq_printf() format string in drivers
cpu: Remove spurious NULL in attribute_group definition
s390/con3215: Remove spurious NULL in attribute_group definition
perf: arm-ni: Remove spurious NULL in attribute_group definition
driver core: Constify bin_attribute definitions
sysfs: attribute_group: allow registration of const bin_attribute
firmware_loader: Fix possible resource leak in fw_log_firmware_info()
drivers: core: fw_devlink: Fix excess parameter description in docstring
driver core: class: Correct WARN() message in APIs class_(for_each|find)_device()
cacheinfo: Use of_property_present() for non-boolean properties
cdx: Fix cdx_mmap_resource() after constifying attr in ->mmap()
drivers: core: fw_devlink: Make the error message a bit more useful
phy: tegra: xusb: Set fwnode for xusb port devices
drm: display: Set fwnode for aux bus devices
driver core: fw_devlink: Stop trying to optimize cycle detection logic
driver core: Constify attribute arguments of binary attributes
sysfs: bin_attribute: add const read/write callback variants
sysfs: implement all BIN_ATTR_* macros in terms of __BIN_ATTR()
sysfs: treewide: constify attribute callback of bin_attribute::llseek()
sysfs: treewide: constify attribute callback of bin_attribute::mmap()
...
-----BEGIN PGP SIGNATURE-----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=2Otz
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Make pci_stop_dev() and pci_destroy_dev() safe so concurrent
callers can't stop a device multiple times, even as we migrate from
the global pci_rescan_remove_lock to finer-grained locking (Keith
Busch)
- Improve pci_walk_bus() implementation by making it recursive and
moving locking up to avoid need for a 'locked' parameter (Keith
Busch)
- Unexport pci_walk_bus_locked(), which is only used internally by
the PCI core (Keith Busch)
- Detect some Thunderbolt chips that are built-in and hence
'trustworthy' by a heuristic since the 'ExternalFacingPort' and
'usb4-host-interface' ACPI properties are not quite enough (Esther
Shimanovich)
Resource management:
- Use PCI bus addresses (not CPU addresses) in 'ranges' properties
when building dynamic DT nodes so systems where PCI and CPU
addresses differ work correctly (Andrea della Porta)
- Tidy resource sizing and assignment with helpers to reduce
redundancy (Ilpo Järvinen)
- Improve pdev_sort_resources() 'bogus alignment' warning to be more
specific (Ilpo Järvinen)
Driver binding:
- Convert driver .remove_new() callbacks to .remove() again to finish
the conversion from returning 'int' to being 'void' (Sergio
Paracuellos)
- Export pcim_request_all_regions(), a managed interface to request
all BARs (Philipp Stanner)
- Replace pcim_iomap_regions_request_all() with
pcim_request_all_regions(), and pcim_iomap_table()[n] with
pcim_iomap(n), in the following drivers: ahci, crypto qat, crypto
octeontx2, intel_th, iwlwifi, ntb idt, serial rp2, ALSA korg1212
(Philipp Stanner)
- Remove the now unused pcim_iomap_regions_request_all() (Philipp
Stanner)
- Export pcim_iounmap_region(), a managed interface to unmap and
release a PCI BAR (Philipp Stanner)
- Replace pcim_iomap_regions(mask) with pcim_iomap_region(n), and
pcim_iounmap_regions(mask) with pcim_iounmap_region(n), in the
following drivers: fpga dfl-pci, block mtip32xx, gpio-merrifield,
cavium (Philipp Stanner)
Error handling:
- Add sysfs 'reset_subordinate' to reset the entire hierarchy below a
bridge; previously Secondary Bus Reset could only be used when
there was a single device below a bridge (Keith Busch)
- Warn if we reset a running device where the driver didn't register
pci_error_handlers notification callbacks (Keith Busch)
ASPM:
- Disable ASPM L1 before touching L1 PM Substates to follow the spec
closer and avoid a CPU load timeout on some platforms (Ajay
Agarwal)
- Set devices below Intel VMD to D0 before enabling ASPM L1 Substates
as required per spec for all L1 Substates changes (Jian-Hong Pan)
Power management:
- Enable starfive controller runtime PM before probing host bridge
(Mayank Rana)
- Enable runtime power management for host bridges (Krishna chaitanya
chundru)
Power control:
- Use of_platform_device_create() instead of of_platform_populate()
to create pwrctl platform devices so we can control it based on the
child nodes (Manivannan Sadhasivam)
- Create pwrctrl platform devices only if there's a relevant power
supply property (Manivannan Sadhasivam)
- Add device link from the pwrctl supplier to the PCI dev to ensure
pwrctl drivers are probed before the PCI dev driver; this avoids a
race where pwrctl could change device power state while the PCI
driver was active (Manivannan Sadhasivam)
- Find pwrctl device for removal with of_find_device_by_node()
instead of searching all children of the parent (Manivannan
Sadhasivam)
- Rename 'pwrctl' to 'pwrctrl' to match new bandwidth controller
('bwctrl') and hotplug files (Bjorn Helgaas)
Bandwidth control:
- Add read/modify/write locking for Link Control 2, which is used to
manage Link speed (Ilpo Järvinen)
- Extract Link Bandwidth Management Status check into
pcie_lbms_seen(), where it can be shared between the bandwidth
controller and quirks that use it to help retrain failed links
(Ilpo Järvinen)
- Re-add Link Bandwidth notification support with updates to address
the reasons it was previously reverted (Alexandru Gagniuc, Ilpo
Järvinen)
- Add pcie_set_target_speed() and related functionality so drivers
can manage PCIe Link speed based on thermal or other constraints
(Ilpo Järvinen)
- Add a thermal cooling driver to throttle PCIe Links via the
existing thermal management framework (Ilpo Järvinen)
- Add a userspace selftest for the PCIe bandwidth controller (Ilpo
Järvinen)
PCI device hotplug:
- Add hotplug controller driver for Marvell OCTEON multi-function
device where function 0 has a management console interface to
enable/disable and provision various personalities for the other
functions (Shijith Thotton)
- Retain a reference to the pci_bus for the lifetime of a pci_slot to
avoid a use-after-free when the thunderbolt driver resets USB4 host
routers on boot, causing hotplug remove/add of downstream docks or
other devices (Lukas Wunner)
- Remove unused cpcihp struct cpci_hp_controller_ops.hardware_test
(Guilherme Giacomo Simoes)
- Remove unused cpqphp struct ctrl_dbg.ctrl (Christophe JAILLET)
- Use pci_bus_read_dev_vendor_id() instead of hand-coded presence
detection in cpqphp (Ilpo Järvinen)
- Simplify cpqphp enumeration, which is already simple-minded and
doesn't handle devices below hot-added bridges (Ilpo Järvinen)
Virtualization:
- Add ACS quirk for Wangxun FF5xxx NICs, which don't advertise an ACS
capability but do isolate functions as though PCI_ACS_RR and
PCI_ACS_CR were set, so the functions can be in independent IOMMU
groups (Mengyuan Lou)
TLP Processing Hints (TPH):
- Add and document TLP Processing Hints (TPH) support so drivers can
enable and disable TPH and the kernel can save/restore TPH
configuration (Wei Huang)
- Add TPH Steering Tag support so drivers can retrieve Steering Tag
values associated with specific CPUs via an ACPI _DSM to improve
performance by directing DMA writes closer to their consumers (Wei
Huang)
Data Object Exchange (DOE):
- Wait up to 1 second for DOE Busy bit to clear before writing a
request to the mailbox to avoid failures if the mailbox is still
busy from a previous transfer (Gregory Price)
Endpoint framework:
- Skip attempts to allocate from endpoint controller memory window if
the requested size is larger than the window (Damien Le Moal)
- Add and document pci_epc_mem_map() and pci_epc_mem_unmap() to
handle controller-specific size and alignment constraints, and add
test cases to the endpoint test driver (Damien Le Moal)
- Implement dwc pci_epc_ops.align_addr() so pci_epc_mem_map() can
observe DWC-specific alignment requirements (Damien Le Moal)
- Synchronously cancel command handler work in endpoint test before
cleaning up DMA and BARs (Damien Le Moal)
- Respect endpoint page size in dw_pcie_ep_align_addr() (Niklas
Cassel)
- Use dw_pcie_ep_align_addr() in dw_pcie_ep_raise_msi_irq() and
dw_pcie_ep_raise_msix_irq() instead of open coding the equivalent
(Niklas Cassel)
- Avoid NULL dereference if Modem Host Interface Endpoint lacks
'mmio' DT property (Zhongqiu Han)
- Release PCI domain ID of Endpoint controller parent (not controller
itself) and before unregistering the controller, to avoid
use-after-free (Zijun Hu)
- Clear secondary (not primary) EPC in pci_epc_remove_epf() when
removing the secondary controller associated with an NTB (Zijun Hu)
Cadence PCIe controller driver:
- Lower severity of 'phy-names' message (Bartosz Wawrzyniak)
Freescale i.MX6 PCIe controller driver:
- Fix suspend/resume support on i.MX6QDL, which has a hardware
erratum that prevents use of L2 (Stefan Eichenberger)
Intel VMD host bridge driver:
- Add 0xb60b and 0xb06f Device IDs for client SKUs (Nirmal Patel)
MediaTek PCIe Gen3 controller driver:
- Update mediatek-gen3 DT binding to require the exact number of
clocks for each SoC (Fei Shao)
- Add support for DT 'max-link-speed' and 'num-lanes' properties to
restrict the link speed and width (AngeloGioacchino Del Regno)
Microchip PolarFlare PCIe controller driver:
- Add DT and driver support for using either of the two PolarFire
Root Ports (Conor Dooley)
NVIDIA Tegra194 PCIe controller driver:
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
Qualcomm PCIe controller driver:
- Add qcom SAR2130P DT binding with an additional clock (Dmitry
Baryshkov)
- Enable MSI interrupts if 'global' IRQ is supported, since a
previous commit unintentionally masked them (Manivannan Sadhasivam)
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
- Add DT binding and driver support for IPQ9574, with Synopsys IP
v5.80a and Qcom IP 1.27.0 (devi priya)
- Move the OPP "operating-points-v2" table from the
qcom,pcie-sm8450.yaml DT binding to qcom,pcie-common.yaml, where it
can be used by other Qcom platforms (Qiang Yu)
- Add 'global' SPI interrupt for events like link-up, link-down to
qcom,pcie-x1e80100 DT binding so we can start enumeration when the
link comes up (Qiang Yu)
- Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned
to support this (Qiang Yu)
- Add ops_1_21_0 for SC8280X family SoC, which doesn't use the
'iommu-map' DT property and doesn't need BDF-to-SID translation
(Qiang Yu)
Rockchip PCIe controller driver:
- Define ROCKCHIP_PCIE_AT_SIZE_ALIGN to replace magic 256 endpoint
.align value (Damien Le Moal)
- When unmapping an endpoint window, compute the region index instead
of searching for it, and verify that the address was mapped (Damien
Le Moal)
- When mapping an endpoint window, verify that the address hasn't
been mapped already (Damien Le Moal)
- Implement pci_epc_ops.align_addr() for rockchip-ep (Damien Le Moal)
- Fix MSI IRQ data mapping to observe the alignment constraint, which
fixes intermittent page faults in memcpy_toio() and memcpy_fromio()
(Damien Le Moal)
- Rename rockchip_pcie_parse_ep_dt() to
rockchip_pcie_ep_get_resources() for consistency with similar DT
interfaces (Damien Le Moal)
- Skip the unnecessary link train in rockchip_pcie_ep_probe() and do
it only in the endpoint start operation (Damien Le Moal)
- Implement pci_epc_ops.stop_link() to disable link training and
controller configuration (Damien Le Moal)
- Attempt link training at 5 GT/s when both partners support it
(Damien Le Moal)
- Add a handler for PERST# signal so we can detect host-initiated
resets and start link training after PERST# is deasserted (Damien
Le Moal)
Synopsys DesignWare PCIe controller driver:
- Clear outbound address on unmap so dw_pcie_find_index() won't match
an ATU index that was already unmapped (Damien Le Moal)
- Use of_property_present() instead of of_property_read_bool() when
testing for presence of non-boolean DT properties (Rob Herring)
- Advertise 1MB size if endpoint supports Resizable BARs, which was
inadvertently lost in v6.11 (Niklas Cassel)
TI J721E PCIe driver:
- Add PCIe support for J722S SoC (Siddharth Vadapalli)
- Delay PCIE_T_PVPERL_MS (100 ms), not just PCIE_T_PERST_CLK_US (100
us), before deasserting PERST# to ensure power and refclk are
stable (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Set the 'ti,keystone-pcie' mode so v3.65a devices work in Root
Complex mode (Kishon Vijay Abraham I)
- Try to avoid unrecoverable SError for attempts to issue config
transactions when the link is down; this is racy but the best we
can do (Kishon Vijay Abraham I)
Miscellaneous:
- Reorganize kerneldoc parameter names to match order in function
signature (Julia Lawall)
- Fix sysfs reset_method_store() memory leak (Todd Kjos)
- Simplify pci_create_slot() (Ilpo Järvinen)
- Fix incorrect printf format specifiers in pcitest (Luo Yifan)"
* tag 'pci-v6.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (127 commits)
PCI: rockchip-ep: Handle PERST# signal in EP mode
PCI: rockchip-ep: Improve link training
PCI: rockship-ep: Implement the pci_epc_ops::stop_link() operation
PCI: rockchip-ep: Refactor endpoint link training enable
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() MSI-X hiding
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() memory allocations
PCI: rockchip-ep: Rename rockchip_pcie_parse_ep_dt()
PCI: rockchip-ep: Fix MSI IRQ data mapping
PCI: rockchip-ep: Implement the pci_epc_ops::align_addr() operation
PCI: rockchip-ep: Improve rockchip_pcie_ep_map_addr()
PCI: rockchip-ep: Improve rockchip_pcie_ep_unmap_addr()
PCI: rockchip-ep: Use a macro to define EP controller .align feature
PCI: rockchip-ep: Fix address translation unit programming
PCI/pwrctrl: Rename pwrctrl functions and structures
PCI/pwrctrl: Rename pwrctl files to pwrctrl
PCI/pwrctl: Remove pwrctl device without iterating over all children of pwrctl parent
PCI/pwrctl: Ensure that pwrctl drivers are probed before PCI client drivers
PCI/pwrctl: Create pwrctl device only if at least one power supply is present
PCI/pwrctl: Use of_platform_device_create() to create pwrctl devices
tools: PCI: Fix incorrect printf format specifiers
...
- Add 0xb60b and 0xb06f Device IDs for client SKUs (Nirmal Patel)
* pci/controller/vmd:
PCI: vmd: Add DID 8086:B06F and 8086:B60B for Intel client SKUs
- Move endpoint controller cleanups that depend on refclk from the host to
the notifier that tells us the host has deasserted PERST# (Manivannan
Sadhasivam)
* pci/controller/tegra194:
PCI: tegra194: Move controller cleanups to pex_ep_event_pex_rst_deassert()
- Fix address translation unit programming (Damien Le Moal)
- Define ROCKCHIP_PCIE_AT_SIZE_ALIGN to replace magic 256 endpoint .align
value (Damien Le Moal)
- When unmapping an endpoint window, compute the region index instead of
searching for it, and verify that the address was mapped (Damien Le Moal)
- When mapping an endpoint window, verify that the address hasn't been
mapped already (Damien Le Moal)
- Implement pci_epc_ops.align_addr() for rockchip-ep (Damien Le Moal)
- Fix MSI IRQ data mapping to observe the alignment constraint, which fixes
intermittent page faults in memcpy_toio() and memcpy_fromio() (Damien Le
Moal)
- Rename rockchip_pcie_parse_ep_dt() to rockchip_pcie_ep_get_resources()
for consistency with similar DT interfaces (Damien Le Moal)
- Factor out memory allocations to tidy rockchip_pcie_ep_probe() (Damien Le
Moal)
- Factor out MSI-X quirk to tidy rockchip_pcie_ep_probe() (Damien Le Moal)
- Skip the unnecessary link train in rockchip_pcie_ep_probe() and only in
the endpoint start operation (Damien Le Moal)
- Implement pci_epc_ops.stop_link() to disable link training and controller
configuration (Damien Le Moal)
- Attempt link training at 5 GT/s when both partners support it (Damien Le
Moal)
- Add a handler for PERST# signal so we can detect host resets and start
link training when exiting reset (Damien Le Moal)
* pci/controller/rockchip:
PCI: rockchip-ep: Handle PERST# signal in EP mode
PCI: rockchip-ep: Improve link training
PCI: rockship-ep: Implement the pci_epc_ops::stop_link() operation
PCI: rockchip-ep: Refactor endpoint link training enable
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() MSI-X hiding
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() memory allocations
PCI: rockchip-ep: Rename rockchip_pcie_parse_ep_dt()
PCI: rockchip-ep: Fix MSI IRQ data mapping
PCI: rockchip-ep: Implement the pci_epc_ops::align_addr() operation
PCI: rockchip-ep: Improve rockchip_pcie_ep_map_addr()
PCI: rockchip-ep: Improve rockchip_pcie_ep_unmap_addr()
PCI: rockchip-ep: Use a macro to define EP controller .align feature
PCI: rockchip-ep: Fix address translation unit programming
- Enable MSI interrupts if 'global' IRQ is supported, since a previous
commit unintentionally masked them (Manivannan Sadhasivam)
- Move endpoint controller cleanups that depend on refclk from the host to
the notifier that tells us the host has deasserted PERST# (Manivannan
Sadhasivam)
- Add DT binding and driver support for IPQ9574, with Synopsys IP v5.80a
and Qcom IP 1.27.0 (devi priya)
- Move the OPP "operating-points-v2" table from the qcom,pcie-sm8450.yaml
DT binding to qcom,pcie-common.yaml, where it can be used by other Qcom
platforms (Qiang Yu)
- Add 'global' SPI interrupt for events like link-up, link-down to
qcom,pcie-x1e80100 DT binding so we can start enumeration when the link
comes up (Qiang Yu)
- Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned to
support this (Qiang Yu)
- Add ops_1_21_0 for SC8280X family SoC, which doesn't use the 'iommu-map'
DT property and doesn't need BDF-to-SID translation (Qiang Yu)
* pci/controller/qcom:
PCI: qcom: Disable ASPM L0s for X1E80100
PCI: qcom: Remove BDF2SID mapping config for SC8280X family SoC
dt-bindings: PCI: qcom,pcie-x1e80100: Add 'global' interrupt
dt-bindings: PCI: qcom: Move OPP table to qcom,pcie-common.yaml
PCI: qcom: Add support for IPQ9574
dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller
PCI: qcom-ep: Move controller cleanups to qcom_pcie_perst_deassert()
PCI: qcom: Enable MSI interrupts together with Link up if 'Global IRQ' is supported
- Add DT and driver support for using either of the two PolarFire Root
Ports (Conor Dooley)
* pci/controller/microchip:
PCI: microchip: Add support for using either Root Port 1 or 2
dt-bindings: PCI: microchip,pcie-host: Add reg for Root Port 2
- Add support for DT 'max-link-speed' and 'num-lanes' properties to
restrict the link speed and width (AngeloGioacchino Del Regno)
* pci/controller/mediatek:
PCI: mediatek-gen3: Remove unneeded semicolon
PCI: mediatek-gen3: Add support for restricting link width
PCI: mediatek-gen3: Add support for setting max-link-speed limit
- Set the 'ti,keystone-pcie' mode so v3.65a devices work in Root Complex
mode (Kishon Vijay Abraham I)
- Try to avoid unrecoverable SError for attempts to issue config
transactions when the link is down; this is racy but the best we can do
(Kishon Vijay Abraham I)
* pci/controller/keystone:
PCI: keystone: Add link up check to ks_pcie_other_map_bus()
PCI: keystone: Set mode as Root Complex for "ti,keystone-pcie" compatible
- Add PCIe support for J722S SoC (Siddharth Vadapalli)
- Delay PCIE_T_PVPERL_MS (100 ms), not just PCIE_T_PERST_CLK_US (100 us),
before deasserting PERST# to ensure power and refclk are stable
(Siddharth Vadapalli)
* pci/controller/j721e:
PCI: j721e: Deassert PERST# after a delay of PCIE_T_PVPERL_MS milliseconds
PCI: j721e: Add PCIe support for J722S SoC
- Fix suspend/resume support on i.MX6QDL, which has a hardware erratum that
prevents use of L2 (Stefan Eichenberger)
* pci/controller/imx6:
PCI: imx6: Fix suspend/resume support on i.MX6QDL
- Clear outbound address on unmap so dw_pcie_find_index() won't match an
ATU index that was already unmapped (Damien Le Moal)
- Use of_property_present() instead of of_property_read_bool() when testing
for presence of non-boolean DT properties (Rob Herring)
- Advertise 1MB size if endpoint supports Resizable BARs, which was
inadvertently lost in v6.11 (Niklas Cassel)
* pci/controller/dwc:
PCI: dwc: ep: Fix advertised resizable BAR size regression
PCI: dwc: Use of_property_present() for non-boolean properties
PCI: dwc: endpoint: Clear outbound address on unmap
- Lower severity of 'phy-names' message (Bartosz Wawrzyniak)
* pci/controller/cadence:
PCI: cadence: Lower severity of message when phy-names property is absent in DTS
- Add pci_epc_function_is_valid() to avoid repeating common validation
checks (Damien Le Moal)
- Skip attempts to allocate from endpoint controller memory window if the
requested size is larger than the window (Damien Le Moal)
- Add and document pci_epc_mem_map() and pci_epc_mem_unmap() to handle
controller-specific size and alignment constraints, and add test cases to
the endpoint test driver (Damien Le Moal)
- Implement dwc pci_epc_ops.align_addr() so pci_epc_mem_map() can observe
DWC-specific alignment requirements (Damien Le Moal)
- Synchronously cancel command handler work in endpoint test before
cleaning up DMA and BARs (Damien Le Moal)
- Respect endpoint page size in dw_pcie_ep_align_addr() (Niklas Cassel)
- Use dw_pcie_ep_align_addr() in dw_pcie_ep_raise_msi_irq() and
dw_pcie_ep_raise_msix_irq() instead of open coding the equivalent (Niklas
Cassel)
- Remove superfluous 'return' from pci_epf_test_clean_dma_chan() (Wang
Jiang)
- Avoid NULL dereference if Modem Host Interface Endpoint lacks 'mmio' DT
property (Zhongqiu Han)
- Release PCI domain ID of Endpoint controller parent (not controller
itself) and before unregistering the controller, to avoid use-after-free
(Zijun Hu)
- Clear secondary (not primary) EPC in pci_epc_remove_epf() when removing
the secondary controller associated with an NTB (Zijun Hu)
- Fix pci_epc_map map_size kerneldoc (Rick Wertenbroek)
* pci/endpoint:
PCI: endpoint: Fix pci_epc_map map_size kerneldoc string
PCI: endpoint: Clear secondary (not primary) EPC in pci_epc_remove_epf()
PCI: endpoint: Fix PCI domain ID release in pci_epc_destroy()
PCI: endpoint: epf-mhi: Avoid NULL dereference if DT lacks 'mmio'
PCI: endpoint: Remove surplus return statement from pci_epf_test_clean_dma_chan()
PCI: dwc: ep: Use align addr function for dw_pcie_ep_raise_{msi,msix}_irq()
PCI: endpoint: test: Synchronously cancel command handler work
PCI: dwc: endpoint: Implement the pci_epc_ops::align_addr() operation
PCI: endpoint: test: Use pci_epc_mem_map/unmap()
PCI: endpoint: Update documentation
PCI: endpoint: Introduce pci_epc_mem_map()/unmap()
PCI: endpoint: Improve pci_epc_mem_alloc_addr()
PCI: endpoint: Introduce pci_epc_function_is_valid()
- Add ACS quirk for Wangxun FF5xxx NICs, which don't advertise and ACS
capability but do isolate functions as though PCI_ACS_RR and PCI_ACS_CR
were set, so the functions can be in independent IOMMU groups (Mengyuan
Lou)
* pci/virtualization:
PCI: Add ACS quirk for Wangxun FF5xxx NICs
- Add and document TLP Processing Hints (TPH) support so drivers can enable
and disable TPH and the kernel can save/restore TPH configuration (Wei
Huang)
- Add TPH Steering Tag support so drivers can retrieve Steering Tag values
associated with specific CPUs via an ACPI _DSM to direct DMA writes
closer to their consumers (Wei Huang)
* pci/tph:
PCI/TPH: Add TPH documentation
PCI/TPH: Add Steering Tag support
PCI: Add TLP Processing Hints (TPH) support
- Detect some Thunderbolt chips that are built-in and hence 'trustworthy'
by a heuristic since the 'ExternalFacingPort' and 'usb4-host-interface'
ACPI properties are not quite enough (Esther Shimanovich)
* pci/thunderbolt:
PCI: Detect and trust built-in Thunderbolt chips
- Add resource_set_size() to set resource size when start has already been
set (Ilpo Järvinen)
- Add resource_set_range() helper to set both resource start and size (Ilpo
Järvinen)
- Use IS_ALIGNED() and resource_size() in quirk_s3_64M() instead of
open-coding them (Ilpo Järvinen)
- Add ALIGN_DOWN_IF_NONZERO() to avoid code duplication when distributing
resources across devices (Ilpo Järvinen)
- Improve pdev_sort_resources() warning message to be more specific (Ilpo
Järvinen)
* pci/resource:
PCI: Improve pdev_sort_resources() warning message
PCI: Add ALIGN_DOWN_IF_NONZERO() helper
PCI: Use align and resource helpers, and SZ_* in quirk_s3_64M()
PCI: Use resource_set_{range,size}() helpers
resource: Add resource set range and size helpers
- Add sysfs 'reset_subordinate' to reset hierarchy below bridge (Keith
Busch)
- Warn if we reset a running device where driver didn't register
pci_error_handlers notification callbacks (Keith Busch)
* pci/reset:
PCI: Warn if a running device is unaware of reset
PCI: Add 'reset_subordinate' to reset hierarchy below bridge
- Use of_platform_device_create() instead of of_platform_populate() to
create pwrctl platform devices so we can control it based on the child
nodes (Manivannan Sadhasivam)
- Create pwrctrl platform devices only if there's a relevant power supply
property (Manivannan Sadhasivam)
- Add device link from the pwrctl supplier to the PCI dev to ensure pwrctl
drivers are probed before the PCI dev driver; this avoids a race where
pwrctl could change device power state while the PCI driver was active
(Manivannan Sadhasivam)
- Find pwrctl device for removal with of_find_device_by_node() instead of
searching all children of the parent (Manivannan Sadhasivam)
- Rename 'pwrctl' to 'pwrctrl' to use the same 'ctrl' suffix as 'bwctrl'
and other PCI files to reduce confusion (Bjorn Helgaas)
* pci/pwrctl:
PCI/pwrctrl: Rename pwrctrl functions and structures
PCI/pwrctrl: Rename pwrctl files to pwrctrl
PCI/pwrctl: Remove pwrctl device without iterating over all children of pwrctl parent
PCI/pwrctl: Ensure that pwrctl drivers are probed before PCI client drivers
PCI/pwrctl: Create pwrctl device only if at least one power supply is present
PCI/pwrctl: Use of_platform_device_create() to create pwrctl devices
# Conflicts:
# drivers/pci/bus.c
# drivers/pci/remove.c
- Use PCI bus addresses (not CPU addresses) in 'ranges' properties when
building dynamic DT nodes so systems where the PCI and CPU addresses
space differ work correctly (Andrea della Porta)
* pci/of:
PCI: of_property: Assign PCI instead of CPU bus address to dynamic PCI nodes
- Make pci_stop_dev() and pci_destroy_dev() concurrent safe (Keith Busch)
- Move __pci_walk_bus() mutex up into the caller, which avoids the need for
a parameter to control locking (Keith Busch)
- Simplify __pci_walk_bus() by making it recursive (Keith Busch)
- Unexport pci_walk_bus_locked(), which is only used internally by the PCI
core (Keith Busch)
* pci/locking:
PCI: Unexport pci_walk_bus_locked()
PCI: Convert __pci_walk_bus() to be recursive
PCI: Move __pci_walk_bus() mutex to where we need it
PCI: Make pci_destroy_dev() concurrent safe
PCI: Make pci_stop_dev() concurrent safe
- Add hotplug controller driver for Marvell OCTEON multi-function device
where function 0 has a management console interface to enable/disable and
provision various personalities for the other functions (Shijith Thotton)
* pci/hotplug-octeon:
PCI: hotplug: Add OCTEON PCI hotplug controller driver
- Remove unused cpcihp struct cpci_hp_controller_ops.hardware_test
(Guilherme Giacomo Simoes)
- Remove unused cpqphp struct ctrl_dbg.ctrl (Christophe JAILLET)
- Clean up cpqphp PCIBIOS_* return value confusion (Ilpo Järvinen)
- Use pci_bus_read_dev_vendor_id() instead of hand-coded presence detection
in cpqphp (Ilpo Järvinen)
- Simplify cpqphp enumeration, which is already simple-minded and doesn't
handle devices below hot-added bridges (Ilpo Järvinen)
- Retain a reference to the pci_bus for the lifetime of a pci_slot to avoid
a use-after-free when the thunderbolt driver resets USB4 host routers on
boot, causing hotplug remove/add of downstream docks or other devices
(Lukas Wunner)
* pci/hotplug:
PCI: Fix use-after-free of slot->bus on hot remove
PCI: cpqphp: Simplify PCI_ScanBusForNonBridge()
PCI: cpqphp: Use define to read class/revision dword
PCI: cpqphp: Use pci_bus_read_dev_vendor_id() to detect presence
PCI: cpqphp: Fix PCIBIOS_* return value confusion
PCI: cpqphp: Remove unused struct ctrl_dbg.ctrl
PCI: cpcihp: Remove unused struct cpci_hp_controller_ops.hardware_test
- Convert driver .remove_new() callbacks to .remove() again to finish the
conversion from returning 'int' to being 'void' (Sergio Paracuellos)
* pci/driver-remove:
PCI: acpiphp_ampere_altra: Switch back to struct platform_driver::remove()
PCI: controller: Switch back to struct platform_driver::remove()
- Wait up to 1 second for DOE Busy bit to clear before writing a request to
the mailbox to avoid failures if the mailbox is still busy from a
previous transfer (Gregory Price)
* pci/doe:
PCI/DOE: Poll DOE Busy bit for up to 1 second in pci_doe_send_req()
- Add read/modify/write locking for Link Control 2, which is used to manage
Link speed (Ilpo Järvinen)
- Cache all supported Link speeds for use by the PCIe bandwidth controller
(Ilpo Järvinen)
- Extract the Link Bandwidth Management Status check into pcie_lbms_seen(),
where it can be shared between the bandwidth controller and quirks that
use it to help retrain failed links (Ilpo Järvinen)
- Re-add Link Bandwidth notification support with updates to address the
reasons it was previously reverted (Alexandru Gagniuc, Ilpo Järvinen)
- Add pcie_set_target_speed() and related functionality to manage PCIe Link
speed based on thermal constraints (Ilpo Järvinen)
- Add a thermal cooling driver to throttle PCIe Links via the existing
thermal management framework (Ilpo Järvinen)
- Add a userspace selftest for the PCIe bandwidth controller (Ilpo
Järvinen)
- Drop duplicate pcie_get_speed_cap(), pcie_get_width_cap() declarations
(Bjorn Helgaas)
* pci/bwctrl:
PCI: Drop duplicate pcie_get_speed_cap(), pcie_get_width_cap() declarations
selftests/pcie_bwctrl: Create selftests
thermal: Add PCIe cooling driver
PCI/bwctrl: Add pcie_set_target_speed() to set PCIe Link Speed
PCI/bwctrl: Re-add BW notification portdrv as PCIe BW controller
PCI: Abstract LBMS seen check into pcie_lbms_seen()
PCI: Refactor pcie_update_link_speed()
PCI: Store all PCIe Supported Link Speeds
PCI: Protect Link Control 2 Register with RMW locking
Documentation PCI: Reformat RMW ops documentation
Currently, the Rockchip PCIe endpoint controller driver does not handle
the PERST# signal, which prevents detecting when link training should
actually be started or if the host resets the device. This however can
be supported using the controller reset_gpios property set as an input
GPIO for endpoint mode.
Modify the Rockchip PCI endpoint controller driver to get the reset_gpio
and its associated interrupt which is serviced using a threaded IRQ with
the function rockchip_pcie_ep_perst_irq_thread() as handler.
This handler function notifies a link down event corresponding to the RC
side asserting the PERST# signal using pci_epc_linkdown() when the gpio
is high. Once the gpio value goes down, corresponding to the RC
de-asserting the PERST# signal, link training is started. The polarity
of the gpio interrupt trigger is changed from high to low after the RC
asserted PERST#, and conversely changed from low to high after the RC
de-asserts PERST#.
Also, given that the host mode controller and the endpoint mode
controller use two different property names for the same PERST# signal
(ep_gpios property and reset_gpios property respectively), for clarity,
rename the ep_gpio field of struct rockchip_pcie to perst_gpio.
Link: https://lore.kernel.org/r/20241017015849.190271-14-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: make log messages consistent, add missing include]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Rockchip RK3399 TRM V1.3 Part2, Section 17.5.8.1.2, step 7,
describes the endpoint mode link training process clearly and states
that:
Insure link training completion and success by observing link_st field
in PCIe Client BASIC_STATUS1 register change to 2'b11. If both side
support PCIe Gen2 speed, re-train can be Initiated by asserting the
Retrain Link field in Link Control and Status Register. The software
should insure the BASIC_STATUS0[negotiated_speed] changes to "1", that
indicates re-train to Gen2 successfully.
This procedure is very similar to what is done for the root-port mode
in rockchip_pcie_host_init_port().
Implement this link training procedure for the endpoint mode as well.
Given that the RK3399 SoC does not have an interrupt signaling link
status changes, training is implemented as a delayed work which is
rescheduled until the link training completes or the endpoint controller
is stopped. The link training work is first scheduled in
rockchip_pcie_ep_start() when the endpoint function is started. Link
training completion is signaled to the function using pci_epc_linkup().
Accordingly, the linkup_notifier field of the Rockchip pci_epc_features
structure is changed to true.
Link: https://lore.kernel.org/r/20241017015849.190271-13-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: update log messages to make them consistent]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Define the EPC operation ->stop() for the Rockchip endpoint driver with
the function rockchip_pcie_ep_stop(). This function disables link
training and the controller configuration, as the reverse to what
the start operation defined with rockchip_pcie_ep_start() does.
Link: https://lore.kernel.org/r/20241017015849.190271-12-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The function rockchip_pcie_init_port() enables link training for a
controller configured in EP mode. Enabling link training is again done
in rockchip_pcie_ep_probe() after that function executed
rockchip_pcie_init_port(). Enabling link training only needs to be done
once, and doing so at the probe stage before the controller is actually
started by the user serves no purpose.
Refactor this by removing the link training enablement from both
rockchip_pcie_init_port() and rockchip_pcie_ep_probe() and moving it to
the endpoint start operation defined with rockchip_pcie_ep_start().
Enabling the controller configuration using the PCIE_CLIENT_CONF_ENABLE
bit in the same PCIE_CLIENT_CONFIG register is also moved to
rockchip_pcie_ep_start() and both the controller configuration and link
training enable bits are set with a single call to
rockchip_pcie_write().
Link: https://lore.kernel.org/r/20241017015849.190271-11-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the code in rockchip_pcie_ep_probe() to hide the MSI-X capability
to its own function, rockchip_pcie_ep_hide_broken_msix_cap().
No functional changes.
Link: https://lore.kernel.org/r/20241017015849.190271-10-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Introduce the function rockchip_pcie_ep_init_ob_mem() allocate the
outbound memory regions and memory needed for IRQ handling.
These changes tidy up rockchip_pcie_ep_probe().
No functional change.
Link: https://lore.kernel.org/r/20241017015849.190271-9-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
To be consistent with the usual "get_resources" naming of driver
functions that acquire controller resources like clocks, PHY etc,
rename the function rockchip_pcie_parse_ep_dt() to
rockchip_pcie_ep_get_resources().
No functional changes.
Link: https://lore.kernel.org/r/20241017015849.190271-8-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The call to rockchip_pcie_prog_ep_ob_atu() used to map the PCI address
of MSI data to the memory window allocated on probe for IRQs is done
in rockchip_pcie_ep_send_msi_irq() assuming a fixed alignment to a
256B boundary of the PCI address. This is not correct as the alignment
constraint for the RK3399 PCI mapping depends on the number of bits of
address changing in the mapped region. This leads to an unstable system
which sometimes work and sometimes does not (crashing on paging faults
when memcpy_toio() or memcpy_fromio() are used).
Similar to regular data mapping, the MSI data mapping must thus be
handled according to the information provided by
rockchip_pcie_ep_align_addr(). Modify rockchip_pcie_ep_send_msi_irq()
to use rockchip_pcie_ep_align_addr() to correctly program entry 0 of
the ATU for sending MSI IRQs.
Link: https://lore.kernel.org/r/20241017015849.190271-7-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits from the CPU address space used for the
mapping. For a PCI mapping of size bytes starting from pci_addr, the
number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1], up to 20 bits, that is,
up to 1MB mappings.
This means that when preparing a PCI address mapping, an endpoint
function driver must use an offset into the allocated controller
memory region that is equal to the mask of the starting PCI address
over rockchip_pcie_ep_ob_atu_num_bits() bits. This offset also
determines the maximum size of the mapping given the starting PCI
address and the fixed 1MB controller memory window size.
Implement the ->align_addr() endpoint controller operation to allow the
mapping alignment to be transparently handled by endpoint function
drivers through the function pci_epc_mem_map().
Link: https://lore.kernel.org/r/20241017015849.190271-6-dlemoal@kernel.org
Co-developed-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: change local variable name for address offset]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a check to verify that the outbound region to be used for mapping an
address is not already in use.
Link: https://lore.kernel.org/r/20241017015849.190271-5-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is no need to loop over all regions to find the memory window used
to map an address. We can use rockchip_ob_region() to determine the
region index, together with a check that the address passed as argument
is the address used to create the mapping. Furthermore, the
ob_region_map bitmap should also be checked to ensure that we are not
attempting to unmap an address that is not mapped.
Link: https://lore.kernel.org/r/20241017015849.190271-4-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Introduce the macro ROCKCHIP_PCIE_AT_SIZE_ALIGN to initialize the .align
field of the controller epc_features structure to 256. This is defined
as a shift using the macro ROCKCHIP_PCIE_AT_MIN_NUM_BITS (to avoid
using the "magic" value 8 directly).
Link: https://lore.kernel.org/r/20241017015849.190271-3-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits masked from the CPU address space used for the
mapping. For a PCI mapping of <size> bytes starting from <pci_addr>,
the number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1].
However, rockchip_pcie_prog_ep_ob_atu() calculates num_pass_bits only
using the size of the mapping, resulting in an incorrect number of mask
bits depending on the value of the PCI address to map.
Fix this by introducing the helper function
rockchip_pcie_ep_ob_atu_num_bits() to correctly calculate the number of
mask bits to use to program the address translation unit. The number of
mask bits is calculated depending on both the PCI address and size of
the mapping, and clamped between 8 and 20 using the macros
ROCKCHIP_PCIE_AT_MIN_NUM_BITS and ROCKCHIP_PCIE_AT_MAX_NUM_BITS. As
defined in the Rockchip RK3399 TRM V1.3 Part2, Sections 17.5.5.1.1 and
17.6.8.2.1, this clamping is necessary because:
1) The lower 8 bits of the PCI address to be mapped by the outbound
region are ignored. So a minimum of 8 address bits are needed and
imply that the PCI address must be aligned to 256.
2) The outbound memory regions are 1MB in size. So while we can specify
up to 63-bits for the PCI address (num_bits filed uses bits 0 to 5 of
the outbound address region 0 register), we must limit the number of
valid address bits to 20 to match the memory window maximum size (1
<< 20 = 1MB).
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Link: https://lore.kernel.org/r/20241017015849.190271-2-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Rename pwrctrl functions and structures from "pwrctl" to "pwrctrl" to match
the similar file renames.
Link: https://lore.kernel.org/r/20241115214428.2061153-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
To slightly reduce confusion between "pwrctl" (the power controller and
power sequencing framework) and "bwctrl" (the bandwidth controller),
rename "pwrctl" to "pwrctrl" so they use the same "ctrl" suffix.
Rename drivers/pci/pwrctl/ to drivers/pci/pwrctrl/, including the related
MAINTAINERS, include file (include/linux/pci-pwrctl.h), Makefile, and
Kconfig changes.
This is the minimal rename of files only. A subsequent commit will rename
functions and data structures.
Link: https://lore.kernel.org/r/20241115214428.2061153-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
There is no need to iterate over all children of the pwrctl device parent
to remove the pwrctl device. Since the pwrctl device associated with the
PCI device can be found using of_find_device_by_node() API, use it directly
instead.
Any pwrctl devices lying around without getting associated with the PCI
devices will be removed once their parent device gets removed.
Link: https://lore.kernel.org/r/20241025-pci-pwrctl-rework-v2-5-568756156cbe@linaro.org
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
As per the kernel device driver model, a pwrctl device is the supplier for
the PCI device, but the device link that enforces the supplier-consumer
relationship was previously created by the pwrctl driver. Therefore, the
driver model didn't prevent probing PCI client drivers before probing the
corresponding pwrctl drivers. This may lead to a race condition if the PCI
device was already powered on by the bootloader (before the pwrctl driver).
If the bootloader did not power on the PCI device, this wouldn't create any
problem as the pwrctl driver will be the one powering on the device, so the
PCI client driver always gets probed afterward. But if the device was
already powered on, then the device will be seen by the PCI core and the
PCI client driver may get probed before its pwrctl driver. This creates a
race condition as the pwrctl driver may change the device power state while
the device is being accessed by the client driver.
One such issue was already reported on the Qcom X13s platform with the WLAN
device and fixed with a hack in the WCN pwrseq driver by a9aaf1ff88
("power: sequencing: request the WLAN enable GPIO as-is").
A cleaner way to fix the above mentioned race condition is to ensure that
the pwrctl drivers are always probed before the client drivers.
If the PCI device is associated with a pwrctl platform device with a power
supply, add a device link between the PCI device and the pwrctl device
before device_attach() in pci_bus_add_device().
Note that there is no need to explicitly remove the device link as that
will be taken care of by the driver core when the PCI device gets removed.
Fixes: 4565d2652a ("PCI/pwrctl: Add PCI power control core code")
Fixes: 8fb18619d9 ("PCI/pwrctl: Create platform devices for child OF nodes of the port node")
Link: https://lore.kernel.org/r/20241025-pci-pwrctl-rework-v2-3-568756156cbe@linaro.org
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[bhelgaas: squash fix from
https://lore.kernel.org/r/20241120062459.6371-1-manivannan.sadhasivam@linaro.org
for SPARCv9 issue reported by Jonathan Currier <dullfire@yahoo.com>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: wrap code to 80 columns]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Cc: stable+noautosel@kernel.org # Depends on power supply check
Currently, pwrctl devices are created if the corresponding PCI nodes are
defined in devicetree. But this is not correct, because not all PCI nodes
require pwrctl support. Pwrctl comes into the picture only when the device
requires kernel to manage its power state. This can be determined using the
power supply properties present in the devicetree node of the device.
Add of_pci_supply_present() to check whether the devicetree contains at
least one power supply property for a device. If one is present, create a
pwrctl device for that PCI node.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 8fb18619d9 ("PCI/pwrctl: Create platform devices for child OF nodes of the port node")
Link: https://lore.kernel.org/r/20241025-pci-pwrctl-rework-v2-2-568756156cbe@linaro.org
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[bhelgaas: rename of_pci_is_supply_present() to of_pci_supply_present() for
readability]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Cc: stable+noautosel@kernel.org # Depends on of_platform_device_create() rework
The of_platform_populate() API creates platform devices by descending
through the children of the parent node. But it provides no control over
the child nodes, which makes it difficult to add checks for the child
nodes in the future.
Use of_platform_device_create() and for_each_child_of_node_scoped() to make
it possible to add checks for each node before creating the platform
device.
Link: https://lore.kernel.org/r/20241025-pci-pwrctl-rework-v2-1-568756156cbe@linaro.org
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Nothing particular important in the SoC driver updates, just the usual
improvements to for drivers/soc and a couple of subsystems that don't
fit anywhere else:
- The largest set of updates is for Qualcomm SoC drivers, extending the
set of supported features for additional SoCs in the QSEECOM, LLCC
and socinfo drivers.a
- The ti_sci firmware driver gains support for power managment
- The drivers/reset subsystem sees a rework of the microchip
sparx5 and amlogic reset drivers to support additional chips,
plus a few minor updates on other platforms
- The SCMI firmware interface driver gains support for two protocol
extensions, allowing more flexible use of the shared memory area
and new DT binding properties for configurability.
- Mediatek SoC drivers gain support for power managment on the MT8188
SoC and a new driver for DVFS.
- The AMD/Xilinx ZynqMP SoC drivers gain support for system reboot
and a few bugfixes
- The Hisilicon Kunpeng HCCS driver gains support for configuring
lanes through sysfs
Finally, there are cleanups and minor fixes for drivers/soc, drivers/bus,
and drivers/memory, including changing back the .remove_new callback
to .remove, as well as a few other updates for freescale (powerpc)
soc drivers, NXP i.MX soc drivers, cznic turris platform driver, memory
controller drviers, TI OMAP SoC drivers, and Tegra firmware drivers
-----BEGIN PGP SIGNATURE-----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=xeCE
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"Nothing particular important in the SoC driver updates, just the usual
improvements to for drivers/soc and a couple of subsystems that don't
fit anywhere else:
- The largest set of updates is for Qualcomm SoC drivers, extending
the set of supported features for additional SoCs in the QSEECOM,
LLCC and socinfo drivers.a
- The ti_sci firmware driver gains support for power managment
- The drivers/reset subsystem sees a rework of the microchip sparx5
and amlogic reset drivers to support additional chips, plus a few
minor updates on other platforms
- The SCMI firmware interface driver gains support for two protocol
extensions, allowing more flexible use of the shared memory area
and new DT binding properties for configurability.
- Mediatek SoC drivers gain support for power managment on the MT8188
SoC and a new driver for DVFS.
- The AMD/Xilinx ZynqMP SoC drivers gain support for system reboot
and a few bugfixes
- The Hisilicon Kunpeng HCCS driver gains support for configuring
lanes through sysfs
Finally, there are cleanups and minor fixes for drivers/{soc, bus,
memory}, including changing back the .remove_new callback to .remove,
as well as a few other updates for freescale (powerpc) soc drivers,
NXP i.MX soc drivers, cznic turris platform driver, memory controller
drviers, TI OMAP SoC drivers, and Tegra firmware drivers"
* tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (116 commits)
soc: fsl: cpm1: qmc: Set the ret error code on platform_get_irq() failure
soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
soc: fsl: cpm1: tsa: switch to for_each_available_child_of_node_scoped()
platform: cznic: turris-omnia-mcu: Rename variable holding GPIO line names
platform: cznic: turris-omnia-mcu: Document the driver private data structure
firmware: turris-mox-rwtm: Document the driver private data structure
bus: Switch back to struct platform_driver::remove()
soc: qcom: ice: Remove the device_link field in qcom_ice
drm/msm/adreno: Setup SMMU aparture for per-process page table
firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
soc: qcom: llcc: Flip the manual slice configuration condition
dt-bindings: firmware: qcom,scm: Document sm8750 SCM
firmware: qcom: uefisecapp: Allow X1E Devkit devices
misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
...
Bindings:
- Enable dtc "interrupt_provider" warnings for binding examples.
Fix the warnings in fsl,mu-msi and ti,sci-inta due to this.
- Convert zii,rave-sp-wdt, zii,rave-sp-pwrbutton, and
altr,fpga-passive-serial to DT schema format
- Add some documentation on the different forms of YAML text blocks
which are a constant source of review comments
- Fix some schema errors in constraints for arrays
- Add compatibles for qcom,sar2130p-pdc and onnn,adt7462
DT core:
- Allow overlay kunit tests to run CONFIG_OF_OVERLAY=n
- Add some warnings on deprecated address handling
- Rework early_init_dt_scan() so the arch can pass in the phys address
of the DTB as __pa() is not always valid to use. This fixes a warning
for arm64 with kexec.
- Add and use some new DT graph iterators for iterating over ports and
endpoints
- Rework reserved-memory handling to be sized dynamically for fixed
regions
- Optimize of_modalias() to avoid a strlen() call
- Constify struct device_node and property pointers where ever possible
-----BEGIN PGP SIGNATURE-----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=NCYS
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"Bindings:
- Enable dtc "interrupt_provider" warnings for binding examples. Fix
the warnings in fsl,mu-msi and ti,sci-inta due to this.
- Convert zii,rave-sp-wdt, zii,rave-sp-pwrbutton, and
altr,fpga-passive-serial to DT schema format
- Add some documentation on the different forms of YAML text blocks
which are a constant source of review comments
- Fix some schema errors in constraints for arrays
- Add compatibles for qcom,sar2130p-pdc and onnn,adt7462
DT core:
- Allow overlay kunit tests to run CONFIG_OF_OVERLAY=n
- Add some warnings on deprecated address handling
- Rework early_init_dt_scan() so the arch can pass in the phys
address of the DTB as __pa() is not always valid to use. This fixes
a warning for arm64 with kexec.
- Add and use some new DT graph iterators for iterating over ports
and endpoints
- Rework reserved-memory handling to be sized dynamically for fixed
regions
- Optimize of_modalias() to avoid a strlen() call
- Constify struct device_node and property pointers where ever
possible"
* tag 'devicetree-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (36 commits)
of: Allow overlay kunit tests to run CONFIG_OF_OVERLAY=n
dt-bindings: interrupt-controller: qcom,pdc: Add SAR2130P compatible
of/address: Rework bus matching to avoid warnings
of: WARN on deprecated #address-cells/#size-cells handling
of/fdt: Don't use default address cell sizes for address translation
dt-bindings: Enable dtc "interrupt_provider" warnings
of/fdt: add dt_phys arg to early_init_dt_scan and early_init_dt_verify
dt-bindings: cache: qcom,llcc: Fix X1E80100 reg entries
dt-bindings: watchdog: convert zii,rave-sp-wdt.txt to yaml format
dt-bindings: input: convert zii,rave-sp-pwrbutton.txt to yaml
media: xilinx-tpg: use new of_graph functions
fbdev: omapfb: use new of_graph functions
gpu: drm: omapdrm: use new of_graph functions
ASoC: audio-graph-card2: use new of_graph functions
ASoC: audio-graph-card: use new of_graph functions
ASoC: test-component: use new of_graph functions
of: property: use new of_graph functions
of: property: add of_graph_get_next_port_endpoint()
of: property: add of_graph_get_next_port()
of: module: remove strlen() call in of_modalias()
...
In addition to a primary endpoint controller, an endpoint function may be
associated with a secondary endpoint controller, epf->sec_epc, to provide
NTB (non-transparent bridge) functionality.
Previously, pci_epc_remove_epf() incorrectly cleared epf->epc instead of
epf->sec_epc when removing from the secondary endpoint controller.
Extend the epc->list_lock coverage and clear either epf->epc or
epf->sec_epc as indicated.
Link: https://lore.kernel.org/r/20241107-epc_rfc-v2-2-da5b6a99a66f@quicinc.com
Fixes: 63840ff532 ("PCI: endpoint: Add support to associate secondary EPC with EPF")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: reworded subject and description]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
pci_epc_destroy() invokes pci_bus_release_domain_nr() to release the PCI
domain ID, but there are two issues:
- 'epc->dev' is passed to pci_bus_release_domain_nr() which was already
freed by device_unregister(), leading to a use-after-free issue.
- Domain ID corresponds to the EPC device parent, so passing 'epc->dev'
is also wrong.
Fix these issues by passing 'epc->dev.parent' to
pci_bus_release_domain_nr() and also do it before device_unregister().
Fixes: 0328947c50 ("PCI: endpoint: Assign PCI domain number for endpoint controllers")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241107-epc_rfc-v2-1-da5b6a99a66f@quicinc.com
[mani: reworded subject and description]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Link: https://lore.kernel.org/r/20241104190714.275977-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If platform_get_resource_byname() fails and returns NULL because DT lacks
an 'mmio' property for the MHI endpoint, dereferencing res->start will
cause a NULL pointer access. Add a check to prevent it.
Fixes: 1bf5f25324 ("PCI: endpoint: Add PCI Endpoint function driver for MHI bus")
Link: https://lore.kernel.org/r/20241105120735.1240728-1-quic_zhonhan@quicinc.com
Signed-off-by: Zhongqiu Han <quic_zhonhan@quicinc.com>
[kwilczynski: error message update per the review feedback]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Remove a surplus return statement from the void function that has been
added in the commit commit 8353813c88 ("PCI: endpoint: Enable DMA
tests for endpoints with DMA capabilities").
Especially, as an empty return statements at the end of a void functions
serve little purpose.
This fixes the following checkpatch.pl script warning:
WARNING: void function return statements are not generally useful
#296: FILE: drivers/pci/endpoint/functions/pci-epf-test.c:296:
+ return;
+}
Link: https://lore.kernel.org/r/tencent_F250BEE2A65745A524E2EFE70CF615CA8F06@qq.com
Signed-off-by: Wang Jiang <jiangwang@kylinos.cn>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Use the dw_pcie_ep_align_addr() function to calculate the alignment in
dw_pcie_ep_raise_{msi,msix}_irq() instead of open coding the same.
Link: https://lore.kernel.org/r/20241017132052.4014605-6-cassel@kernel.org
Link: https://lore.kernel.org/r/20241104205144.409236-2-cassel@kernel.org
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[kwilczynski: squashed patch that fixes memory map sizes]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
6cf57be0f7 ("PCI: Add pcie_get_speed_cap() to find max supported link
speed") and c70b65fb7f ("PCI: Add pcie_get_width_cap() to find max
supported link width") added declarations to drivers/pci/pci.h.
576c7218a1 ("PCI: Export pcie_get_speed_cap and pcie_get_width_cap")
subsequently added duplicates to include/linux/pci.h.
Remove the originals from drivers/pci/pci.h. Both interfaces are used by
amdgpu, so they must be in include/linux/pci.h.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Add a thermal cooling driver to provide path to access PCIe bandwidth
controller using the usual thermal interfaces.
A cooling device is instantiated for controllable PCIe Ports from the
bwctrl service driver.
If registering the cooling device fails, allow bwctrl's probe to succeed
regardless. As cdev in that case contains IS_ERR() pseudo "pointer", clean
that up inside the probe function so the remove side doesn't need to
suddenly make an odd looking IS_ERR() check.
The thermal side state 0 means no throttling, i.e., maximum supported PCIe
Link Speed.
Link: https://lore.kernel.org/r/20241018144755.7875-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: dropped data->cdev test per
https://lore.kernel.org/r/ZzRm1SJTwEMRsAr8@wunner.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # From the cooling device interface perspective
Currently, PCIe Link Speeds are adjusted by custom code rather than in a
common function provided in PCI core. The PCIe bandwidth controller
(bwctrl) introduces an in-kernel API, pcie_set_target_speed(), to set PCIe
Link Speed.
Convert Target Speed quirk to use the new API. The Target Speed quirk runs
very early when bwctrl is not yet probed for a Port and can also run later
when bwctrl is already setup for the Port, which requires the per port
mutex (set_speed_mutex) to be only taken if the bwctrl setup is already
complete.
The new API is also intended to be used in an upcoming commit that adds a
thermal cooling device to throttle PCIe bandwidth when thermal thresholds
are reached.
The PCIe bandwidth control procedure is as follows. The highest speed
supported by the Port and the PCIe device which is not higher than the
requested speed is selected and written into the Target Link Speed in the
Link Control 2 Register. Then bandwidth controller retrains the PCIe Link.
Bandwidth Notifications enable the cur_bus_speed in the struct pci_bus to
keep track PCIe Link Speed changes. While Bandwidth Notifications should
also be generated when bandwidth controller alters the PCIe Link Speed, a
few platforms do not deliver LMBS interrupt after Link Training as
expected. Thus, after changing the Link Speed, bandwidth controller makes
additional read for the Link Status Register to ensure cur_bus_speed is
consistent with the new PCIe Link Speed.
Link: https://lore.kernel.org/r/20241018144755.7875-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: squash devm_mutex_init() error checking from
https://lore.kernel.org/r/20241030163139.2111689-1-andriy.shevchenko@linux.intel.com,
drop export of pcie_set_target_speed()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This mostly reverts the commit b4c7d2076b ("PCI/LINK: Remove bandwidth
notification"). An upcoming commit extends this driver building PCIe
bandwidth controller on top of it.
PCIe bandwidth notifications were first added in the commit e8303bb7a7
("PCI/LINK: Report degraded links via link bandwidth notification") but
later had to be removed. The significant changes compared with the old
bandwidth notification driver include:
1) Don't print the notifications into kernel log, just keep the Link
Speed cached in struct pci_bus updated. While somewhat unfortunate,
the log spam was the source of complaints that eventually lead to
the removal of the bandwidth notifications driver (see the links
below for further information).
2) Besides the Link Bandwidth Management Interrupt, also enable Link
Autonomous Bandwidth Interrupt to cover the other source of bandwidth
changes.
3) Handle Link Speed updates robustly. Refresh the cached Link Speed
when enabling Bandwidth Notification Interrupts, and solve the race
between Link Speed read and LBMS/LABS update in
pcie_bwnotif_irq_thread().
4) Use concurrency safe LNKCTL RMW operations.
5) The driver is now called PCIe bwctrl (bandwidth controller) instead
of just bandwidth notifications because of increased scope and
functionality within the driver.
6) Coexist with the Target Link Speed quirk in pcie_failed_link_retrain().
Provide LBMS counting API for it.
7) Tweaks to variable/functions names for consistency and length reasons.
Bandwidth Notifications enable the cur_bus_speed in the struct pci_bus to
keep track PCIe Link Speed changes.
[bhelgaas: This is based on previous work by Alexandru Gagniuc
<mr.nuke.me@gmail.com>; see e8303bb7a7 ("PCI/LINK: Report degraded links
via link bandwidth notification")]
Link: https://lore.kernel.org/r/20241018144755.7875-7-ilpo.jarvinen@linux.intel.com
Link: https://lore.kernel.org/all/20190429185611.121751-1-helgaas@kernel.org/
Link: https://lore.kernel.org/linux-pci/20190501142942.26972-1-keith.busch@intel.com/
Link: https://lore.kernel.org/linux-pci/20200115221008.GA191037@google.com/
Suggested-by: Lukas Wunner <lukas@wunner.de> # Building bwctrl on top of bwnotif
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: squash fix to drop IRQF_ONESHOT and convert to hardirq handler:
https://lore.kernel.org/r/20241115165717.15233-1-ilpo.jarvinen@linux.intel.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Wangxun FF5xxx NICs are similar to SFxxx, RP1000 and RP2000 NICs. They may
be multi-function devices, but they do not advertise an ACS capability.
But the hardware does isolate FF5xxx functions as though it had an ACS
capability and PCI_ACS_RR and PCI_ACS_CR were set in the ACS Control
register, i.e., all peer-to-peer traffic is directed upstream instead of
being routed internally.
Add ACS quirk for FF5xxx NICs in pci_quirk_wangxun_nic_acs() so the
functions can be in independent IOMMU groups.
Link: https://lore.kernel.org/r/E16053DB2B80E9A5+20241115024604.30493-1-mengyuanlou@net-swift.com
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a PCI hotplug controller driver for the OCTEON PCIe device. The OCTEON
PCIe device is a multi-function device where function 0 serves as the PCI
hotplug controller.
There is an out-of-band management console interface to firmware running on
function 0 whereby an administrator can disable functions to save power or
enable them with one of several personalities (virtio-net, virtio-crypto,
NVMe, etc) for the other functions. Function 0 initiates hotplug events
handled by this driver when the other functions are enabled or disabled.
+--------------------------------+
| Root Port |
+--------------------------------+
|
PCIe
|
+---------------------------------------------------------------+
| OCTEON PCIe Multifunction Device |
+---------------------------------------------------------------+
| | | |
| | | |
+---------------------+ +----------------+ +-----+ +----------------+
| Function 0 | | Function 1 | | ... | | Function 7 |
| (Hotplug controller)| | (Hotplug slot) | | | | (Hotplug slot) |
+---------------------+ +----------------+ +-----+ +----------------+
|
|
+-------------------------+
| Controller Firmware |
+-------------------------+
The hotplug controller driver enables hotplugging of non-controller
functions within the same device. During probing, the driver removes
the non-controller functions and registers them as PCI hotplug slots.
These slots are added back by the driver, only upon request from the
device firmware.
The controller uses MSI-X interrupts to notify the host of hotplug
events initiated by the OCTEON firmware. Additionally, the driver
allows users to enable or disable individual functions via sysfs slot
entries, as provided by the PCI hotplug framework.
Link: https://lore.kernel.org/r/20241111134523.2796699-1-sthotton@marvell.com
Co-developed-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Shijith Thotton <sthotton@marvell.com>
[bhelgaas: use pci_info() when possible]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If a reset is issued to a running device with a driver that didn't register
the notification callbacks, the driver may be unaware of this event and
have an inconsistent view of the device's state. Log a warning of this
event because there's nothing else indicating the event occured, which
could be confusing when debugging such situations.
Link: https://lore.kernel.org/r/20241025222755.3756162-2-kbusch@meta.com
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Amey Narkhede <ameynarkhede03@gmail.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
The "bus" and "cxl_bus" reset methods reset a device by asserting Secondary
Bus Reset on the bridge leading to the device. These only work if the
device is the only device below the bridge.
Add a sysfs 'reset_subordinate' attribute on bridges that can assert
Secondary Bus Reset regardless of how many devices are below the bridge.
This resets all the devices below a bridge in a single command, including
the locking and config space save/restore that reset methods normally do.
This may be the only way to reset devices that don't support other reset
methods (ACPI, FLR, PM reset, etc).
Link: https://lore.kernel.org/r/20241025222755.3756162-1-kbusch@meta.com
Signed-off-by: Keith Busch <kbusch@kernel.org>
[bhelgaas: commit log, add capable(CAP_SYS_ADMIN) check]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Amey Narkhede <ameynarkhede03@gmail.com>
The controller driver is the parent device of the PCIe host bridge,
PCI-PCI bridge and PCIe endpoint as shown below.
PCIe controller (Top level parent & parent of host bridge)
|
v
PCIe Host bridge (Parent of PCI-PCI bridge)
|
v
PCI-PCI bridge (Parent of endpoint driver)
|
v
PCIe endpoint driver
Now, when the controller device goes to runtime suspend, PM framework will
check the runtime PM state of the child device (host bridge) and will find
it to be disabled. So it will allow the parent (controller device) to go to
runtime suspend. Only if the child device's state was 'active' it will
prevent the parent to get suspended.
It is a property of the runtime PM framework that it can only follow
continuous dependency chains. That is, if there is a device with runtime
PM disabled in a dependency chain, runtime PM cannot be enabled for devices
below it and above it in that chain both at the same time.
Since runtime PM is disabled for host bridge, the state of the child
devices under the host bridge is not taken into account by PM framework for
the top level parent, PCIe controller. So the PM framework allows the
controller driver to enter runtime PM irrespective of the state of the
devices under the host bridge. And this causes the topology breakage and
also possible PM issues like controller driver going to runtime suspend
while the endpoint driver is doing transfers.
Because of the above, in order to enable runtime PM for a PCIe controller
device, one needs to ensure that runtime PM is enabled for all devices in
every dependency chain between it and any PCIe endpoint (as runtime PM is
enabled for PCIe endpoints).
This means that runtime PM needs to be enabled for the host bridge device,
which is present in all of these dependency chains.
After this change, the host bridge device will be runtime-suspended by the
runtime PM framework automatically after suspending its last child and it
will be runtime-resumed automatically before resuming its first child which
will allow the runtime PM framework to track dependencies between the host
bridge device and all of its descendants.
The PM framework expects parent runtime PM to be enabled before enabling
runtime PM of the child. Ensure pm_runtime_enable() is called for the
controller drivers before calling pci_host_probe().
Link: https://lore.kernel.org/r/20241111-runtime_pm-v7-2-9c164eefcd87@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
A PCI controller device, e.g., StarFive, is parent to PCI host bridge
device. We must enable runtime PM of the controller before enabling runtime
PM of the host bridge, which will happen in pci_host_probe(), to avoid this
warning:
pcie-starfive 940000000.pcie: Enabling runtime PM for inactive device with active children
Fix this issue by enabling StarFive controller device's runtime PM before
calling pci_host_probe() in plda_pcie_host_init().
Link: https://lore.kernel.org/r/20241111-runtime_pm-v7-1-9c164eefcd87@quicinc.com
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mayank Rana <quic_mrana@quicinc.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Remove a surplus semicolon and fix the following warning:
./drivers/pci/controller/pcie-mediatek-gen3.c:414:2-3: Unneeded semicolon
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=11789
Link: https://lore.kernel.org/r/20241111010935.20208-1-yang.lee@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The "phy-names" property is optional, so the message indicating its
absence during the probe should be of "info" severity rather than
"error" severity.
Link: https://lore.kernel.org/r/20241018113045.2050295-1-bwawrzyn@cisco.com
Signed-off-by: Bartosz Wawrzyniak <bwawrzyn@cisco.com>
[kwilczynski: update log messages wording, commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
* Split the Amlogic reset-meson driver into platform and auxiliary
bus drivers. Add support for the reset controller in the G12 and
SM1 audio clock controllers.
* Replace the list of boolean parameters to the internal
reset_control_get functions with an enum reset_flags bitfield,
to make the code more self-descriptive.
* Add devres helpers to request pre-deasserted (and automatically
re-asserting during cleanup) reset controls. This allows reducing
boilerplate in drivers that deassert resets for the lifetime of a
device.
* Use the new auto-deasserting devres helpers in reset-uniphier-glue
as an example.
* Add support for the LAN966x PCI device in drivers/misc, as a
dependency for the following reset-microchip-sparx5 patches.
* Add support for being used on the LAN966x PCI device to the
reset-microchip-sparx5 driver.
Commit 86f134941a ("MAINTAINERS: Add the Microchip LAN966x PCI driver
entry") introduces a trivial merge conflict with commit 7280f01e79
("net: lan969x: add match data for lan969x") from the net-next tree [1].
[1] https://lore.kernel.org/all/20241101122505.3eacd183@canb.auug.org.au/
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCZyn4gxcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwFJZAP0fjXG07qnGp1Sgai/pmCesg5xJ
PAEL5/hKaYwQsAQHhwEAwaJg+kVeb74ez3ae4akyvngasJJT9LLDmqWEdxPIcw0=
=cyUW
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=rxJh
-----END PGP SIGNATURE-----
Merge tag 'reset-for-v6.13' of git://git.pengutronix.de/pza/linux into soc/drivers
Reset controller updates for v6.13
* Split the Amlogic reset-meson driver into platform and auxiliary
bus drivers. Add support for the reset controller in the G12 and
SM1 audio clock controllers.
* Replace the list of boolean parameters to the internal
reset_control_get functions with an enum reset_flags bitfield,
to make the code more self-descriptive.
* Add devres helpers to request pre-deasserted (and automatically
re-asserting during cleanup) reset controls. This allows reducing
boilerplate in drivers that deassert resets for the lifetime of a
device.
* Use the new auto-deasserting devres helpers in reset-uniphier-glue
as an example.
* Add support for the LAN966x PCI device in drivers/misc, as a
dependency for the following reset-microchip-sparx5 patches.
* Add support for being used on the LAN966x PCI device to the
reset-microchip-sparx5 driver.
Commit 86f134941a ("MAINTAINERS: Add the Microchip LAN966x PCI driver
entry") introduces a trivial merge conflict with commit 7280f01e79
("net: lan969x: add match data for lan969x") from the net-next tree [1].
[1] https://lore.kernel.org/all/20241101122505.3eacd183@canb.auug.org.au/
* tag 'reset-for-v6.13' of git://git.pengutronix.de/pza/linux: (21 commits)
misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
reset: mchp: sparx5: set the dev member of the reset controller
reset: mchp: sparx5: Allow building as a module
reset: mchp: sparx5: Add MCHP_LAN966X_PCI dependency
reset: mchp: sparx5: Map cpu-syscon locally in case of LAN966x
MAINTAINERS: Add the Microchip LAN966x PCI driver entry
misc: Add support for LAN966x PCI device
reset: uniphier-glue: Use devm_reset_control_bulk_get_shared_deasserted()
reset: Add devres helpers to request pre-deasserted reset controls
reset: replace boolean parameters with flags parameter
reset: amlogic: Fix small whitespace issue
reset: amlogic: add auxiliary reset driver support
reset: amlogic: split the device core and platform probe
reset: amlogic: move drivers to a dedicated directory
reset: amlogic: add reset status support
reset: amlogic: use reset number instead of register count
reset: amlogic: add driver parameters
reset: amlogic: make parameters unsigned
reset: amlogic: use generic data matching function
...
Link: https://lore.kernel.org/r/20241105105229.3729474-1-p.zabel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There's only one user of pci_walk_bus_locked(), and it's internal to the
PCI core. Unexport it and make it private to drivers/pci/.
Link: https://lore.kernel.org/r/20241022224851.340648-6-kbusch@meta.com
Signed-off-by: Keith Busch <kbusch@kernel.org>
[bhelgaas: move decl to drivers/pci/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The Target Speed quirk in pcie_failed_link_retrain() uses the presence of
LBMS bit as one of the triggering conditions, effectively monopolizing the
use of that bit. An upcoming change will introduce a PCIe bandwidth
controller which sets up an interrupt to track LBMS. As LBMS will be
cleared by the interrupt handler, the Target Speed quirk will no longer be
able to observe LBMS directly.
As a preparatory step for the change, extract the LBMS seen check from
pcie_failed_link_retrain() into a new function pcie_lmbs_seen().
Link: https://lore.kernel.org/r/20241018144755.7875-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
pcie_update_link_speed() is passed the Link Status register but not all
callers have that value at hand nor need the value.
Refactor pcie_update_link_speed() to include reading the Link Status
register and create __pcie_update_link_speed() which can be used by the
hotplug code that has the register value at hand beforehand (and needs the
value for other purposes).
Link: https://lore.kernel.org/r/20241018144755.7875-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The PCIe bandwidth controller added by a subsequent commit will require
selecting PCIe Link Speeds that are lower than the Maximum Link Speed.
The struct pci_bus only stores max_bus_speed. Even if PCIe r6.1 sec 8.2.1
currently disallows gaps in supported Link Speeds, the Implementation Note
in PCIe r6.1 sec 7.5.3.18, recommends determining supported Link Speeds
using the Supported Link Speeds Vector in the Link Capabilities 2 Register
(when available) to "avoid software being confused if a future
specification defines Links that do not require support for all slower
speeds."
Reuse code in pcie_get_speed_cap() to add pcie_get_supported_speeds() to
query the Supported Link Speeds Vector of a PCIe device. The value is taken
directly from the Supported Link Speeds Vector or synthesized from the Max
Link Speed in the Link Capabilities Register when the Link Capabilities 2
Register is not available.
The Supported Link Speeds Vector in the Link Capabilities Register 2
corresponds to the bus below on Root Ports and Downstream Ports, whereas it
corresponds to the bus above on Upstream Ports and Endpoints (PCIe r6.1 sec
7.5.3.18):
Supported Link Speeds Vector - This field indicates the supported Link
speed(s) of the associated Port.
Add supported_speeds into the struct pci_dev that caches the
Supported Link Speeds Vector.
supported_speeds contains a set of Link Speeds only in the case where PCIe
Link Speed can be determined. Root Complex Integrated Endpoints do not have
a well-defined Link Speed because they do not implement either of the Link
Capabilities Registers, which is allowed by PCIe r6.1 sec 7.5.3 (the same
limitation applies to determining cur_bus_speed and max_bus_speed that are
PCI_SPEED_UNKNOWN in such case). This is of no concern from PCIe bandwidth
controller point of view because such devices are not attached into a PCIe
Root Port that could be controlled.
The supported_speeds field keeps the extra reserved zero at the least
significant bit to match the Link Capabilities 2 Register layout.
An attempt was made to store supported_speeds field into the struct pci_bus
as an intersection of both ends of the Link, however, the subordinate
struct pci_bus is not available early enough. The Target Speed quirk (in
pcie_failed_link_retrain()) can run either during initial scan or later,
requiring it to use the API provided by the PCIe bandwidth controller to
set the Target Link Speed in order to co-exist with the bandwidth
controller. When the Target Speed quirk is calling the bandwidth controller
during initial scan, the struct pci_bus is not yet initialized. As such,
storing supported_speeds into the struct pci_bus is not viable.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20241018144755.7875-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: move pcie_get_supported_speeds() decl to drivers/pci/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The original implementation of __pci_walk_bus() chose a non-recursive walk,
presumably as a precaution on stack use. We do recursive bus walking in
other places though. For example:
pci_bus_resettable()
pci_stop_bus_device()
pci_remove_bus_device()
pci_bus_allocate_dev_resources()
So recursive pci bus walking is well tested and safe, and is easier to
follow.
Convert __pci_walk_bus() to be recursive to make it easier to introduce
finer grain locking in the future.
Link: https://lore.kernel.org/r/20241022224851.340648-5-kbusch@meta.com
Signed-off-by: Keith Busch <kbusch@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Simplify __pci_walk_bus() by moving the pci_bus_sem mutex into
pci_walk_bus(), the only place it is needed, and removing the parameter
that told __pci_walk_bus() whether to acquire the mutex.
Link: https://lore.kernel.org/r/20241022224851.340648-4-kbusch@meta.com
Signed-off-by: Keith Busch <kbusch@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Use an atomic flag instead of the racy check against the device's kobj
parent. We shouldn't be poking into device implementation details at this
level anyway.
Link: https://lore.kernel.org/r/20241022224851.340648-3-kbusch@meta.com
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the atomic ADDED flag to ensure concurrent callers can't attempt to
stop the device multiple times. Callers should currently all be holding the
pci_rescan_remove_lock, so there shouldn't be an existing race. But that
global lock can cause lock dependency issues, so this is preparing to
reduce reliance on that lock by using the existing existing atomic bit ops.
Link: https://lore.kernel.org/r/20241022224851.340648-2-kbusch@meta.com
Signed-off-by: Keith Busch <kbusch@kernel.org>
[bhelgaas: squash https://lore.kernel.org/r/20241111180659.3321671-1-kbusch@meta.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
K2G forwards the error triggered by a link-down state (e.g., no connected
endpoint device) on the system bus for PCI configuration transactions;
these errors are reported as an SError at system level, which is fatal and
hangs the system.
So, apply fix similar to how it was done in the DesignWare Core driver
commit 15b2390634 ("PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()").
Fixes: 10a797c6e5 ("PCI: dwc: keystone: Use pci_ops for config space accessors")
Link: https://lore.kernel.org/r/20240524105714.191642-3-s-vadapalli@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
commit 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x
Platforms") introduced configuring "enum dw_pcie_device_mode" as part of
device data ("struct ks_pcie_of_data"). However it failed to set the
mode for "ti,keystone-pcie" compatible.
Since the mode defaults to "DW_PCIE_UNKNOWN_TYPE", the following error
message is displayed for the v3.65a controller:
"INVALID device type 0"
Despite the driver probing successfully, the controller may not be
functional in the Root Complex mode of operation.
So, set the mode as Root Complex for "ti,keystone-pcie" compatible to
fix this.
Fixes: 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms")
Link: https://lore.kernel.org/r/20240524105714.191642-2-s-vadapalli@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
The PCI host controller on PolarFire SoC has multiple Root Port instances,
each with their own bridge and ctrl address spaces. The original binding
has an "apb" register region, and it is expected to be set to the base
address of the Root Complex register space. Some defines in the Linux
driver were used to compute the addresses of the bridge and ctrl address
ranges corresponding to Root Port instance 1. Some customers want to use
Root Port instance 2 however, which requires changing the defines in the
driver, which is clearly not a portable solution.
The binding has been changed from a single register region to a pair,
corresponding to the bridge and ctrl regions respectively, so modify the
driver to read these regions directly from the devicetree rather than
compute them from the base address of the abp region.
To maintain backwards compatibility with the existing binding, the driver
retains code to handle the "abp" reg and computes the base address of the
bridge and ctrl regions using the defines if it is present. reg-names has
always been a required property, so this is safe to do.
Link: https://lore.kernel.org/r/20241107-surrender-brisket-287d563a5de1@spud
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[bhelgaas: Capitalize PCIe spec terms]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pcim_ioumap_region() has recently been made a public function and does
not have the disadvantage of having to deal with the legacy iomap table,
as pcim_iounmap_regions() does.
Deprecate pcim_iounmap_regions().
Link: https://lore.kernel.org/r/20241016094911.24818-4-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some computers with CPUs that lack Thunderbolt features use discrete
Thunderbolt chips to add Thunderbolt functionality. These Thunderbolt
chips are located within the chassis; between the Root Port labeled
ExternalFacingPort and the USB-C port.
These Thunderbolt PCIe devices should be labeled as fixed and trusted, as
they are built into the computer. Otherwise, security policies that rely on
those flags may have unintended results, such as preventing USB-C ports
from enumerating.
Detect the above scenario through the process of elimination.
1) Integrated Thunderbolt host controllers already have Thunderbolt
implemented, so anything outside their external facing Root Port is
removable and untrusted.
Detect them using the following properties:
- Most integrated host controllers have the "usb4-host-interface"
ACPI property, as described here:
https://learn.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#mapping-native-protocols-pcie-displayport-tunneled-through-usb4-to-usb4-host-routers
- Integrated Thunderbolt PCIe Root Ports before Alder Lake do not
have the "usb4-host-interface" ACPI property. Identify those by
their PCI IDs instead.
2) If a Root Port does not have integrated Thunderbolt capabilities, but
has the "ExternalFacingPort" ACPI property, that means the
manufacturer has opted to use a discrete Thunderbolt host controller
that is built into the computer.
This host controller can be identified by virtue of being located
directly below an external-facing Root Port that lacks integrated
Thunderbolt. Label it as trusted and fixed.
Everything downstream from it is untrusted and removable.
The "ExternalFacingPort" ACPI property is described here:
https://learn.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#identifying-externally-exposed-pcie-root-ports
Link: https://lore.kernel.org/r/20240910-trust-tbt-fix-v5-1-7a7a42a5f496@chromium.org
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Esther Shimanovich <eshimanovich@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
The remapped PCIe Root Port and the child device have PM L1 Substates
capability, but they are disabled originally.
Here is a failed example on ASUS B1400CEAE:
Capabilities: [900 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1- L1_PM_Substates+
PortCommonModeRestoreTime=32us PortTPowerOnTime=10us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=101376ns
L1SubCtl2: T_PwrOn=50us
Enable PCI-PM L1 PM Substates for devices below VMD while they are in D0
(see PCIe r6.0, sec 5.5.4).
Link: https://lore.kernel.org/r/20241001083438.10070-4-jhp@endlessos.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218394
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Add support for this VMD device which supports the bus restriction mode.
The feature that turns off vector 0 for MSI-X remapping is also enabled.
Link: https://lore.kernel.org/r/20241011175657.249948-1-nirmal.patel@linux.intel.com
Signed-off-by: Nirmal Patel <nirmal.patel@linux.ntel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The suspend/resume functionality is currently broken on the i.MX6QDL
platform, as documented in the NXP errata (ERR005723):
https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
This patch addresses the issue by sharing most of the suspend/resume
sequences used by other i.MX devices, while avoiding modifications to
critical registers that disrupt the PCIe functionality. It targets the
same problem as the following downstream commit:
4e92355e1f
Unlike the downstream commit, this patch also resets the connected PCIe
device if possible. Without this reset, certain drivers, such as ath10k
or iwlwifi, will crash on resume. The device reset is also done by the
driver on other i.MX platforms, making this patch consistent with
existing practices.
Upon resuming, the kernel will hang and display an error. Here's an
example of the error encountered with the ath10k driver:
ath10k_pci 0000:01:00.0: Unable to change power state from D3hot to D0, device inaccessible
Unhandled fault: imprecise external abort (0x1406) at 0x0106f944
Without this patch, suspend/resume will fail on i.MX6QDL devices if a
PCIe device is connected.
Link: https://lore.kernel.org/r/20241030103250.83640-1-eichest@gmail.com
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: stable@vger.kernel.org
Add support for restricting the port's link width by specifying
the num-lanes devicetree property in the PCIe node.
The setting is done in the GEN_SETTINGS register (in the driver
named as PCIE_SETTING_REG), where each set bit in [11:8] activates
a set of lanes (from bits 11 to 8 respectively, x16/x8/x4/x2).
Link: https://lore.kernel.org/r/20241104114935.172908-3-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The llseek() callbacks should not modify the struct
bin_attribute passed as argument.
Enforce this by marking the argument as const.
As there are not many callback implementers perform this change
throughout the tree at once.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20241103-sysfs-const-bin_attr-v2-7-71110628844c@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mmap() callbacks should not modify the struct
bin_attribute passed as argument.
Enforce this by marking the argument as const.
As there are not many callback implementers perform this change
throughout the tree at once.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Andrew Donnellan <ajd@linux.ibm.com> # ocxl
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20241103-sysfs-const-bin_attr-v2-6-71110628844c@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The is_bin_visible() callbacks should not modify the struct
bin_attribute passed as argument.
Enforce this by marking the argument as const.
As there are not many callback implementers perform this change
throughout the tree at once.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20241103-sysfs-const-bin_attr-v2-5-71110628844c@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop abusing the is_bin_visible() callback to calculate the attribute
size. Instead use the new, dedicated bin_size() one.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20241103-sysfs-const-bin_attr-v2-3-71110628844c@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use cancel_delayed_work_sync() in pci_epf_test_epc_deinit() to ensure
that the command handler is really stopped before proceeding with DMA
and BAR cleanup.
The same change is also done in pci_epf_test_link_down() to ensure that
the link down handling completes with the command handler fully stopped.
Link: https://lore.kernel.org/r/20241017010648.189889-1-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
The function dw_pcie_prog_outbound_atu() used to program outbound ATU
entries for mapping RC PCI addresses to local CPU addresses does not
allow PCI addresses that are not aligned to the value of region_align
of struct dw_pcie. This value is determined from the iATU hardware
registers during probing of the iATU (done by dw_pcie_iatu_detect()).
This value is thus valid for all DWC PCIe controllers, and valid
regardless of the hardware configuration used when synthesizing the
DWC PCIe controller.
Implement the ->align_addr() endpoint controller operation to allow
this mapping alignment to be transparently handled by endpoint function
drivers through the function pci_epc_mem_map().
Link: https://lore.kernel.org/linux-pci/20241012113246.95634-7-dlemoal@kernel.org
Link: https://lore.kernel.org/linux-pci/20241015090712.112674-1-dlemoal@kernel.org
Link: https://lore.kernel.org/linux-pci/20241017132052.4014605-5-cassel@kernel.org
Co-developed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[mani: squashed the patch that changed phy_addr_t to u64]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: squashed patch that updated the pci_size variable]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for respecting the max-link-speed devicetree property,
forcing a maximum speed (Gen) for a PCI-Express port.
Since the MediaTek PCIe Gen3 controllers also expose the maximum
supported link speed in the PCIE_BASE_CFG register, if property
max-link-speed is specified in devicetree, validate it against the
controller capabilities and proceed setting the limitations only
if the wanted Gen is lower than the maximum one that is supported
by the controller itself (otherwise it makes no sense!).
Link: https://lore.kernel.org/r/20241104114935.172908-2-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
[kwilczynski: change dev_dbg() to dev_info() and update message wording]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the cfg_1_9_0 which is being used for X1E80100 doesn't disable
ASPM L0s. However, hardware team recommends to disable L0s as the PHY init
sequence is not tuned support L0s. Hence reuse cfg_sc8280xp for X1E80100.
Note that the config_sid() callback is not present in cfg_sc8280xp, don't
concern about this because config_sid() callback is originally a no-op
for X1E80100.
Fixes: 6d0c39324c ("PCI: qcom: Add X1E80100 PCIe support")
Link: https://lore.kernel.org/r/20241101030902.579789-5-quic_qianyu@quicinc.com
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.9
The SC8280XP PCIe devicetree nodes do not specify an 'iommu-map' so
the config_sid() callback is effectively a no-op.
Hence introduce a new ops struct, namely ops_1_21_0 which is same as
ops_1_9_0 except that it doesn't have config_sid() callback to clean
it up.
Link: https://lore.kernel.org/r/20241101030902.579789-4-quic_qianyu@quicinc.com
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
According to Section 2.2 of the PCI Express Card Electromechanical
Specification (Revision 5.1), in order to ensure that the power and the
reference clock are stable, PERST# has to be deasserted after a delay of
100 milliseconds (TPVPERL).
Currently, it is being assumed that the power is already stable, which
is not necessarily true.
Hence, change the delay to PCIE_T_PVPERL_MS to guarantee that power and
reference clock are stable.
Fixes: f3e25911a4 ("PCI: j721e: Add TI J721E PCIe driver")
Fixes: f96b697137 ("PCI: j721e: Use T_PERST_CLK_US macro")
Link: https://lore.kernel.org/r/20241104074420.1862932-1-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add the new IPQ9574 platform which is based on the Qcom IP rev. 1.27.0
and Synopsys IP rev. 5.80a.
The platform itself has four PCIe Gen3 controllers: two single-lane and
two dual-lane, all are based on Synopsys IP rev. 5.70a. As such, reuse
all the members of 'ops_2_9_0'.
Link: https://lore.kernel.org/r/20240801054803.3015572-5-quic_srichara@quicinc.com
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
TI's J722S SoC has one instance of PCIe namely PCIe0 which is a Gen3
single lane PCIe controller. Add support for the "ti,j722s-pcie-host"
compatible specific to J722S SoC.
Link: https://lore.kernel.org/r/20240524092349.158443-1-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Currently, the endpoint cleanup function dw_pcie_ep_cleanup() and EPF
deinit notify function pci_epc_deinit_notify() are called during the
execution of pex_ep_event_pex_rst_assert() i.e., when the host has asserted
PERST#. But quickly after this step, refclk will also be disabled by the
host.
All of the tegra194 endpoint SoCs supported as of now depend on the refclk
from the host for keeping the controller operational. Due to this
limitation, any access to the hardware registers in the absence of refclk
will result in a whole endpoint crash. Unfortunately, most of the
controller cleanups require accessing the hardware registers (like eDMA
cleanup performed in dw_pcie_ep_cleanup(), etc...). So these cleanup
functions can cause the crash in the endpoint SoC once host asserts PERST#.
One way to address this issue is by generating the refclk in the endpoint
itself and not depending on the host. But that is not always possible as
some of the endpoint designs do require the endpoint to consume refclk from
the host.
Thus, fix this crash by moving the controller cleanups to the start of
the pex_ep_event_pex_rst_deassert() function. This function is called
whenever the host has deasserted PERST# and it is guaranteed that the
refclk would be active at this point. So at the start of this function
(after enabling resources) the controller cleanup can be performed. Once
finished, rest of the code execution for PERST# deassert can continue as
usual.
Fixes: 473b2cf9c4 ("PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF drivers")
Fixes: 570d7715ee ("PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST#")
Link: https://lore.kernel.org/r/20240817-pci-qcom-ep-cleanup-v1-2-d6b958226559@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Currently, the endpoint cleanup function dw_pcie_ep_cleanup() and EPF
deinit notify function pci_epc_deinit_notify() are called during the
execution of qcom_pcie_perst_assert() i.e., when the host has asserted
PERST#. But quickly after this step, refclk will also be disabled by the
host.
All of the Qcom endpoint SoCs supported as of now depend on the refclk from
the host for keeping the controller operational. Due to this limitation,
any access to the hardware registers in the absence of refclk will result
in a whole endpoint crash. Unfortunately, most of the controller cleanups
require accessing the hardware registers (like eDMA cleanup performed in
dw_pcie_ep_cleanup(), powering down MHI EPF etc...). So these cleanup
functions are currently causing the crash in the endpoint SoC once host
asserts PERST#.
One way to address this issue is by generating the refclk in the endpoint
itself and not depending on the host. But that is not always possible as
some of the endpoint designs do require the endpoint to consume refclk from
the host (as I was told by the Qcom engineers).
Thus, fix this crash by moving the controller cleanups to the start of
the qcom_pcie_perst_deassert() function. qcom_pcie_perst_deassert() is
called whenever the host has deasserted PERST# and it is guaranteed that
the refclk would be active at this point. So at the start of this function
(after enabling resources), the controller cleanup can be performed. Once
finished, rest of the code execution for PERST# deassert can continue as
usual.
Fixes: 473b2cf9c4 ("PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF drivers")
Fixes: 570d7715ee ("PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST#")
Link: https://lore.kernel.org/r/20240817-pci-qcom-ep-cleanup-v1-1-d6b958226559@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Currently, if 'Global IRQ' is supported by the platform, only the Link up
interrupt is enabled in the PARF_INT_ALL_MASK register. This masks MSIs
on some platforms. The MSI bits in PARF_INT_ALL_MASK register are enabled
by default in the hardware, but commit 4581403f67 ("PCI: qcom: Enumerate
endpoints based on Link up event in 'global_irq' interrupt") disabled them
and enabled only the Link up interrupt. While MSI continued to work on the
SM8450 platform that was used to test the offending commit, on other
platforms like SM8250, X1E80100, MSIs are getting masked. And they require
enabling the MSI interrupt bits in the register to unmask (enable) the
MSIs.
Even though the MSI interrupt enable bits in PARF_INT_ALL_MASK are
described as 'diagnostic' interrupts in the internal documentation,
disabling them masks MSI on these platforms. Due to this, MSIs were not
reported to be received these platforms while supporting 'Global IRQ'.
So, enable the MSI interrupts along with the Link up interrupt in the
PARF_INT_ALL_MASK register if 'Global IRQ' is supported. This ensures that
the MSIs continue to work and also the driver is able to catch the Link
up interrupt for enumerating endpoint devices.
Fixes: 4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt")
Closes: https://lore.kernel.org/linux-pci/9a692c98-eb0a-4d86-b642-ea655981ff53@kernel.org/
Link: https://lore.kernel.org/r/20241007051255.4378-1-manivannan.sadhasivam@linaro.org
Reported-by: Konrad Dybcio <konradybcio@kernel.org>
Tested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> # SL7
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Qiang Yu <quic_qianyu@quicinc.com>
-----BEGIN PGP SIGNATURE-----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=9o9y
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.12-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fix from Bjorn Helgaas:
- Enable device-specific ACS-like functionality even if the device
doesn't advertise an ACS capability, which got broken when adding
fancy ACS kernel parameter (Jason Gunthorpe)
* tag 'pci-v6.12-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: Fix pci_enable_acs() support for the ACS quirks
Dennis reports a boot crash on recent Lenovo laptops with a USB4 dock.
Since commit 0fc7088656 ("thunderbolt: Reset USB4 v2 host router") and
commit 59a54c5f3d ("thunderbolt: Reset topology created by the boot
firmware"), USB4 v2 and v1 Host Routers are reset on probe of the
thunderbolt driver.
The reset clears the Presence Detect State and Data Link Layer Link Active
bits at the USB4 Host Router's Root Port and thus causes hot removal of the
dock.
The crash occurs when pciehp is unbound from one of the dock's Downstream
Ports: pciehp creates a pci_slot on bind and destroys it on unbind. The
pci_slot contains a pointer to the pci_bus below the Downstream Port, but
a reference on that pci_bus is never acquired. The pci_bus is destroyed
before the pci_slot, so a use-after-free ensues when pci_slot_release()
accesses slot->bus.
In principle this should not happen because pci_stop_bus_device() unbinds
pciehp (and therefore destroys the pci_slot) before the pci_bus is
destroyed by pci_remove_bus_device().
However the stacktrace provided by Dennis shows that pciehp is unbound from
pci_remove_bus_device() instead of pci_stop_bus_device(). To understand
the significance of this, one needs to know that the PCI core uses a two
step process to remove a portion of the hierarchy: It first unbinds all
drivers in the sub-hierarchy in pci_stop_bus_device() and then actually
removes the devices in pci_remove_bus_device(). There is no precaution to
prevent driver binding in-between pci_stop_bus_device() and
pci_remove_bus_device().
In Dennis' case, it seems removal of the hierarchy by pciehp races with
driver binding by pci_bus_add_devices(). pciehp is bound to the
Downstream Port after pci_stop_bus_device() has run, so it is unbound by
pci_remove_bus_device() instead of pci_stop_bus_device(). Because the
pci_bus has already been destroyed at that point, accesses to it result in
a use-after-free.
One might conclude that driver binding needs to be prevented after
pci_stop_bus_device() has run. However it seems risky that pci_slot points
to pci_bus without holding a reference. Solely relying on correct ordering
of driver unbind versus pci_bus destruction is certainly not defensive
programming.
If pci_slot has a need to access data in pci_bus, it ought to acquire a
reference. Amend pci_create_slot() accordingly. Dennis reports that the
crash is not reproducible with this change.
Abridged stacktrace:
pcieport 0000:00:07.0: PME: Signaling with IRQ 156
pcieport 0000:00:07.0: pciehp: Slot #12 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ IbPresDis- LLActRep+
pci_bus 0000:20: dev 00, created physical slot 12
pcieport 0000:00:07.0: pciehp: Slot(12): Card not present
...
pcieport 0000:21:02.0: pciehp: pcie_disable_notification: SLOTCTRL d8 write cmd 0
Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] PREEMPT SMP NOPTI
CPU: 13 UID: 0 PID: 134 Comm: irq/156-pciehp Not tainted 6.11.0-devel+ #1
RIP: 0010:dev_driver_string+0x12/0x40
pci_destroy_slot
pciehp_remove
pcie_port_remove_service
device_release_driver_internal
bus_remove_device
device_del
device_unregister
remove_iter
device_for_each_child
pcie_portdrv_remove
pci_device_remove
device_release_driver_internal
bus_remove_device
device_del
pci_remove_bus_device (recursive invocation)
pci_remove_bus_device
pciehp_unconfigure_device
pciehp_disable_slot
pciehp_handle_presence_or_link_change
pciehp_ist
Link: https://lore.kernel.org/r/4bfd4c0e976c1776cd08e76603903b338cf25729.1728579288.git.lukas@wunner.de
Reported-by: Dennis Wassenberg <Dennis.Wassenberg@secunet.com>
Closes: https://lore.kernel.org/r/6de4b45ff2b32dd91a805ec02ec8ec73ef411bf6.camel@secunet.com/
Tested-by: Dennis Wassenberg <Dennis.Wassenberg@secunet.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
The function pcim_iounmap_regions() is problematic because it uses a
bitmask mechanism to release / iounmap multiple BARs at once. It, thus,
prevents getting rid of the problematic iomap table mechanism which was
deprecated in commit e354bb84a4 ("PCI: Deprecate pcim_iomap_table(),
pcim_iomap_regions_request_all()").
pcim_iounmap_region() does not have that problem. Make it public as the
successor of pcim_iounmap_regions().
Link: https://lore.kernel.org/r/20241016094911.24818-3-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pcim_iomap_regions_request_all() have been deprecated in
commit e354bb84a4 ("PCI: Deprecate pcim_iomap_table(),
pcim_iomap_regions_request_all()").
All users of this function have been ported to other interfaces by now.
Remove pcim_iomap_regions_request_all().
Link: https://lore.kernel.org/r/20241030112743.104395-11-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
In order to remove the deprecated function
pcim_iomap_regions_request_all(), a few drivers need an interface to
request all BARs a PCI device offers.
Make pcim_request_all_regions() a public interface.
Link: https://lore.kernel.org/r/20241030112743.104395-2-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
There are ACS quirks that hijack the normal ACS processing and deliver to
to special quirk code. The enable path needs to call
pci_dev_specific_enable_acs() and then pci_dev_specific_acs_enabled() will
report the hidden ACS state controlled by the quirk.
The recent rework got this out of order and we should try to call
pci_dev_specific_enable_acs() regardless of any actual ACS support in the
device.
As before command line parameters that effect standard PCI ACS don't
interact with the quirk versions, including the new config_acs= option.
Link: https://lore.kernel.org/r/0-v1-f96b686c625b+124-pci_acs_quirk_fix_jgg@nvidia.com
Fixes: 47c8846a49 ("PCI: Extend ACS configurability")
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Closes: https://lore.kernel.org/all/e89107da-ac99-4d3a-9527-a4df9986e120@kernel.org
Closes: https://bugzilla.suse.com/show_bug.cgi?id=1229019
Tested-by: Steffen Dirkwinkel <me@steffen.cc>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Clear the address mapped (outbound_addr array) in dw_pcie_ep_unmap_addr(),
to ensure that dw_pcie_find_index() does not match an ATU index that was
already unmapped.
This is in addition to clearing the ATU index bit in ob_window_map.
Link: https://lore.kernel.org/linux-pci/20241004141000.5080-1-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmcbz4UUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vxKsQ//f9wMVMlWkuL0O0vQBTp6kD5m4Cck
hpXy84166sLhH/EgKuhcM69aKxJdY94j0Q2nVCVDErP6UTl8BnaQzKwOu9zK4XUD
GlKd5EvPgURdIvQgJIcZbCQGdBVIw/08nVHxXsOHzyewIdnDFt2sOQOMxDnolztG
E5OWOOHA2T3leeWGFdr5fDl4VZ8URtloJwK+FJZWkdKEichuRmNo/Hs//SRc8plh
bK16Zi+yEu9ABBtgu1HjQ9hPYWhudFPmpvaNB3JW5dek2iqe9bzswmvdO2iW1AHh
xttHnqFpWBVa+Uvrn73vFBC1Elb3wWSJgHGWs2RnsBtGHZWuvqLtodnVqbcWA5Yu
jY9eWyegEYtJaWWllgiZNk4S6sBJdHStLqJsz4IZW6qXMBT/+/+JMdYpsu5gD4NC
PdXW+2E5FIl9bRxFDNXt6jjaUGo3O/OwX0gTArXkj4C6GiPv2bTnIf4JeffaxdrA
JR/LkgmRNwguA4tsTZAuOiG/DRwf7RMiui55Yf91cuNitiHZnlrKWepJI+LcLSUl
CBRagPJ5JWGeiBxtpuEcW0rAOLbF4NcNc6aoe7zNak4Jdg4tGNwfgeWMw0egTJq8
1dP2msvX82jCeyh4QbdUj6+NLE4YZar8WAB0+/WC5LVQuVkrIYLfR8tot1HBd6mX
512QPvzdluGyJmE=
=L6G0
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Hold the rescan lock while adding devices to avoid race with
concurrent pwrctl rescan that can lead to a crash (Bartosz
Golaszewski)
- Avoid binding pwrctl driver to QCom WCN wifi if the DT lacks the
necessary PMU regulator descriptions (Bartosz Golaszewski)
* tag 'pci-v6.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/pwrctl: Abandon QCom WCN probe on pre-pwrseq device-trees
PCI: Hold rescan lock while adding devices during host probe
Add a PCI driver that handles the LAN966x PCI device using a device-tree
overlay. This overlay is applied to the PCI device DT node and allows to
describe components that are present in the device.
The memory from the device-tree is remapped to the BAR memory thanks to
"ranges" properties computed at runtime by the PCI core during the PCI
enumeration.
The PCI device itself acts as an interrupt controller and is used as the
parent of the internal LAN966x interrupt controller to route the
interrupts to the assigned PCI INTx interrupt.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # quirks.c
Link: https://lore.kernel.org/r/20241014124636.24221-2-herve.codina@bootlin.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Old device trees for some platforms already define wifi nodes for the WCN
family of chips since before power sequencing was added upstream.
These nodes don't consume the regulator outputs from the PMU, and if we
allow this driver to bind to one of such "incomplete" nodes, we'll see a
kernel log error about the infinite probe deferral.
Extend the driver by adding a platform data struct matched against the
compatible. This struct contains the pwrseq target string as well as a
validation function called right after entering probe().
For Qualcomm WCN models, check the existence of the regulator supply
property that indicates the DT is already using power sequencing and return
-ENODEV if it's not there, indicating to the driver model that the device
should not be bound to the pwrctl driver.
Link: https://lore.kernel.org/r/20241007092447.18616-1-brgl@bgdev.pl
Fixes: 6140d185a4 ("PCI/pwrctl: Add a PCI power control driver for power sequenced devices")
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/all/Zv565olMDDGHyYVt@hovoldconsulting.com/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe r6.2, sec 5.5.4, requires that:
If setting either or both of the enable bits for ASPM L1 PM Substates,
both ports must be configured as described in this section while ASPM L1
is disabled.
Previously, pcie_config_aspm_l1ss() assumed that "setting enable bits"
meant "setting them to 1", and it configured L1SS as follows:
- Clear L1SS enable bits
- Disable L1
- Configure L1SS enable bits as required
- Enable L1 if required
With this sequence, when disabling L1SS on an ARM A-core with a Synopsys
DesignWare PCIe core, the CPU occasionally hangs when reading
PCI_L1SS_CTL1, leading to a reboot when the CPU watchdog expires.
Move the L1 disable to the caller (pcie_config_aspm_link(), where L1 was
already enabled) so L1 is always disabled while updating the L1SS bits:
- Disable L1
- Clear L1SS enable bits
- Configure L1SS enable bits as required
- Enable L1 if required
Change pcie_aspm_cap_init() similarly.
Link: https://lore.kernel.org/r/20241007032917.872262-1-ajayagarwal@google.com
Signed-off-by: Ajay Agarwal <ajayagarwal@google.com>
[bhelgaas: comments, commit log, compute L1SS setting before config access]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI_ScanBusForNonBridge() has two loops, one to search for non-bridges and
a second to look for bridges. The second loop has hints in a debug print it
should do recursion for buses underneath the bridge, but no recursion is
attempted.
Since the second loop is quite useless in its current form, just eliminate
it. This code hasn't been touched for very long time so either it's unused
or the missing parts are not important enough for anyone to attempt to add
them.
Leave only a warning print and comment about the missing recursion for the
unlikely case that somebody comes across the lack of functionality. In any
case, search whether an endpoint exists downstream of a bridge sounds
generic enough to belong to core so if the functionality is to be extended
it should probably be moved into PCI core.
Link: https://lore.kernel.org/r/20241022091140.3504-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The intent of the first part in PCI_RefinedAccessConfig() is to read Vendor
ID register and detect presence of the device that way.
Remove PCI_RefinedAccessConfig() (which was not named very helpfully to
begin with) and replace the call with pci_bus_read_dev_vendor_id() + read
config because it makes the logic more obvious at the caller side.
Link: https://lore.kernel.org/r/20241022091140.3504-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Code in and related to PCI_RefinedAccessConfig() has three types of return
type confusion:
- PCI_RefinedAccessConfig() tests pci_bus_read_config_dword() return value
against -1.
- PCI_RefinedAccessConfig() returns both -1 and PCIBIOS_* return codes.
- Callers of PCI_RefinedAccessConfig() only test for -1.
Make PCI_RefinedAccessConfig() return PCIBIOS_* codes consistently and
adapt callers accordingly.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/20241022091140.3504-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use pci_resource_name() helper in pdev_sort_resources() to print resources
in user-friendly format. Also replace the vague "bogus alignment" with a
more precise explanation of the problem.
Link: https://lore.kernel.org/r/20241017095545.1424-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Philipp Stanner <pstanner@redhat.com>
The 'hardware_test' field in struct cpci_hp_controller_ops is unused;
remove it to reduce resource consumption.
Link: https://lore.kernel.org/r/20241014131917.324667-1-trintaeoitogc@gmail.com
Signed-off-by: Guilherme Giacomo Simoes <trintaeoitogc@gmail.com>
[bhelgas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use reverse logic combined with return and continue to significantly
reduce indentation level in pci_read_bridge_bases().
Link: https://lore.kernel.org/r/20241017141111.44612-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The struct pci_bus_resource is only used in bus.c, so move it there.
Link: https://lore.kernel.org/r/20241017141111.44612-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2fe2abf896 ("PCI: augment bus resource table with a list") added
PCI_SUBTRACTIVE_DECODE which is put into the struct pci_bus_resource flags
field but is never read. There seems to never have been users for it.
Remove both PCI_SUBTRACTIVE_DECODE and the flags field from the struct
pci_bus_resource.
Link: https://lore.kernel.org/r/20241017141111.44612-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Modify the endpoint test driver to use the functions pci_epc_mem_map()
and pci_epc_mem_unmap() for the read, write and copy tests. For each
test case, the transfer (dma or mmio) are executed in a loop to ensure
that potentially partial mappings returned by pci_epc_mem_map() are
correctly handled.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241012113246.95634-6-dlemoal@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Some endpoint controllers have requirements on the alignment of the
controller physical memory address that must be used to map a RC PCI
address region. For instance, the endpoint controller of the RK3399 SoC
uses at most the lower 20 bits of a physical memory address region as
the lower bits of a RC PCI address region. For mapping a PCI address
region of size bytes starting from pci_addr, the exact number of
address bits used is the number of address bits changing in the address
range [pci_addr..pci_addr + size - 1]. For this example, this creates
the following constraints:
1) The offset into the controller physical memory allocated for a
mapping depends on the mapping size *and* the starting PCI address
for the mapping.
2) A mapping size cannot exceed the controller windows size (1MB) minus
the offset needed into the allocated physical memory, which can end
up being a smaller size than the desired mapping size.
Handling these constraints independently of the controller being used
in an endpoint function driver is not possible with the current EPC
API as only the ->align field in struct pci_epc_features is provided
but used for BAR (inbound ATU mappings) mapping only. A new API is
needed for function drivers to discover mapping constraints and handle
non-static requirements based on the RC PCI address range to access.
Introduce the endpoint controller operation ->align_addr() to allow
the EPC core functions to obtain the size and the offset into a
controller address region that must be allocated and mapped to access
a RC PCI address region. The size of the mapping provided by the
align_addr() operation can then be used as the size argument for the
function pci_epc_mem_alloc_addr() and the offset into the allocated
controller memory provided can be used to correctly handle data
transfers. For endpoint controllers that have PCI address alignment
constraints, the align_addr() operation may indicate upon return an
effective PCI address mapping size that is smaller (but not 0) than the
requested PCI address region size.
The controller ->align_addr() operation is optional: controllers that
do not have any alignment constraints for mapping RC PCI address regions
do not need to implement this operation. For such controllers, it is
always assumed that the mapping size is equal to the requested size of
the PCI region and that the mapping offset is 0.
The function pci_epc_mem_map() is introduced to use this new controller
operation (if it is defined) to handle controller memory allocation and
mapping to a RC PCI address region in endpoint function drivers.
This function first uses the ->align_addr() controller operation to
determine the controller memory address size (and offset into) needed
for mapping an RC PCI address region. The result of this operation is
used to allocate a controller physical memory region using
pci_epc_mem_alloc_addr() and then to map that memory to the RC PCI
address space with pci_epc_map_addr().
Since ->align_addr() () may indicate that not all of a RC PCI address
region can be mapped, pci_epc_mem_map() may only partially map the RC
PCI address region specified. It is the responsibility of the caller
(an endpoint function driver) to handle such smaller mapping by
repeatedly using pci_epc_mem_map() over the desried PCI address range.
The counterpart of pci_epc_mem_map() to unmap and free a mapped
controller memory address region is pci_epc_mem_unmap().
Both functions operate using the new struct pci_epc_map data structure.
This new structure represents a mapping PCI address, mapping effective
size, the size of the controller memory needed for the mapping as well
as the physical and virtual CPU addresses of the mapping (phys_base and
virt_base fields). For convenience, the physical and virtual CPU
addresses within that mapping to use to access the target RC PCI address
region are also provided (phys_addr and virt_addr fields).
Endpoint function drivers can use struct pci_epc_map to access the
mapped RC PCI address region using the ->virt_addr and ->pci_size
fields.
Co-developed-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241012113246.95634-4-dlemoal@kernel.org
[mani: squashed the patch that changed phy_addr_t to u64]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
pci_register_io_range() does not modify the passed in fwnode_handle, so
make it const.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241010-dt-const-v1-1-87a51f558425@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
During initial device probe, the PCI DOE busy bit for some CXL devices may
be left set for a longer period than expected by the current driver logic.
Despite local comments stating DOE Busy is unlikely to be detected, it
appears commonly specifically during boot when CXL devices are being
probed.
The symptom was messages like this:
endpoint6: DOE failed -EBUSY
produced by cxl_cdat_get_length() or cxl_cdat_read_table().
This was observed on a single socket AMD platform with 2 CXL memory
expanders attached to the single socket. It was not the case that
concurrent accesses were being made, as validated by monitoring mailbox
commands on the device side.
This behavior has been observed with multiple CXL memory expanders from
different vendors - so it appears unrelated to the model.
In all observed tests, only a small period of the retry window is actually
used - typically only a handful of loop iterations.
Polling on the PCI DOE Busy Bit for (at max) one PCI DOE timeout interval
(1 second), resolves this issue cleanly.
Per PCIe r6.2 sec 6.30.3, the DOE Busy Bit being cleared does not raise an
interrupt, so polling is the best option in this scenario.
Subsequent code in doe_statemachine_work() and abort paths also wait for up
to 1 PCI DOE timeout interval, so this order of (potential) additional
delay is presumed acceptable.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20241004162828.314-1-gourry@gourry.net
Signed-off-by: Gregory Price <gourry@gourry.net>
[bhelgaas: fix nits and add error message to commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since adding the PCI power control code, we may end up with a race between
the pwrctl platform device rescanning the bus and host controller probe
functions. The latter need to take the rescan lock when adding devices or
we may end up in an undefined state having two incompletely added devices
and hit the following crash when trying to remove the device over sysfs:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Internal error: Oops: 0000000096000004 [#1] SMP
Call trace:
__pi_strlen+0x14/0x150
kernfs_find_ns+0x80/0x13c
kernfs_remove_by_name_ns+0x54/0xf0
sysfs_remove_bin_file+0x24/0x34
pci_remove_resource_files+0x3c/0x84
pci_remove_sysfs_dev_files+0x28/0x38
pci_stop_bus_device+0x8c/0xd8
pci_stop_bus_device+0x40/0xd8
pci_stop_and_remove_bus_device_locked+0x28/0x48
remove_store+0x70/0xb0
dev_attr_store+0x20/0x38
sysfs_kf_write+0x58/0x78
kernfs_fop_write_iter+0xe8/0x184
vfs_write+0x2dc/0x308
ksys_write+0x7c/0xec
Fixes: 4565d2652a ("PCI/pwrctl: Add PCI power control core code")
Link: https://lore.kernel.org/r/20241003084342.27501-1-brgl@bgdev.pl
Reported-by: Konrad Dybcio <konradybcio@kernel.org>
Tested-by: Konrad Dybcio <konradybcio@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is no point in attempting to allocate memory from an endpoint
controller memory window if the requested size is larger than the memory
window size. Add a check to skip bitmap_find_free_region() calls for
such case. This check can be done without the mem->lock mutex held as
memory window sizes are constant and never modified at runtime.
Also change the final return to return NULL to simplify the code.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241012113246.95634-3-dlemoal@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Introduce the epc core helper function pci_epc_function_is_valid() to
verify that an epc pointer, a physical function number and a virtual
function number are all valid. This avoids repeating the code pattern:
if (IS_ERR_OR_NULL(epc) || func_no >= epc->max_functions)
return err;
if (vfunc_no > 0 && (!epc->max_vfs || vfunc_no > epc->max_vfs[func_no]))
return err;
in many functions of the endpoint controller core code.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20241012113246.95634-2-dlemoal@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
pci_bus_distribute_available_resources() performs alignment in case of
non-zero alignment requirement on three occasions.
Add ALIGN_DOWN_IF_NONZERO() helper to avoid coding the non-zero check three
times.
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240614100606.15830-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use IS_ALIGNED(), resource_size(), and SZ_* defines in quirk_s3_64M().
Link: https://lore.kernel.org/r/20240614100606.15830-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert open-coded resource size calculations to use
resource_set_{range,size}() helpers.
While at it, use SZ_* for size parameter where appropriate which makes the
intent of code more obvious.
Also, cast sizes to resource_size_t, not u64.
Link: https://lore.kernel.org/r/20240614100606.15830-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simplify pci_create_slot() by splitting an "if" statement into two parts.
In order to not duplicate error handling, add a new label to handle kobj
put.
Link: https://lore.kernel.org/r/20241004152240.7926-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
After commit 0edb555a65 ("platform: Make platform_driver::remove() return
void") .remove() is (again) the right callback to implement for platform
drivers.
Convert all PCI controller drivers to use .remove(), with the eventual goal
to drop struct platform_driver::remove_new(). As .remove() and
.remove_new() have the same prototypes, conversion is done by just changing
the structure member name in the driver initializer.
Link: https://lore.kernel.org/r/20240927092449.44628-1-sergio.paracuellos@gmail.com
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
After commit 0edb555a65 ("platform: Make platform_driver::remove() return
void") .remove() is (again) the right callback to implement for platform
drivers.
Convert all PCI controller drivers to use .remove(), with the eventual goal
to drop struct platform_driver::remove_new(). As .remove() and .remove_new()
have the same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Link: https://lore.kernel.org/r/20240923065706.728769-1-sergio.paracuellos@gmail.com
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
[bhelgaas: add pcie-xilinx-nwl.c and tidy whitespace per Uwe Kleine-König:
https://lore.kernel.org/r/tdxrmmqyzcufupnwkdbg7lwgadizm7v3lxjirykijbml7x54ze@upbdzycdsilm]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In reset_method_store(), a string is allocated via kstrndup() and assigned
to the local "options". options is then used in with strsep() to find
spaces:
while ((name = strsep(&options, " ")) != NULL) {
If there are no remaining spaces, then options is set to NULL by strsep(),
so the subsequent kfree(options) doesn't free the memory allocated via
kstrndup().
Fix by using a separate tmp_options to iterate with strsep() so options is
preserved.
Link: https://lore.kernel.org/r/20241001231147.3583649-1-tkjos@google.com
Fixes: d88f521da3 ("PCI: Allow userspace to query and set device reset mechanism")
Signed-off-by: Todd Kjos <tkjos@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Add pcie_tph_get_cpu_st() to allow a caller to retrieve Steering Tags for a
target memory associated with a specific CPU. The ST tag is retrieved by
invoking PCI ACPI "_DSM to Query Cache Locality TPH Features" method
(rev=0x7, func=0xF) of the device's Root Port device.
Add pcie_tph_set_st_entry() to update the device's Steering Tags. The tags
will be written into the device's MSI-X table or the ST table located in
the TPH Extended Capability space.
Co-developed-by: Eric Van Tassell <Eric.VanTassell@amd.com>
Link: https://lore.kernel.org/r/20241002165954.128085-3-wei.huang2@amd.com
Signed-off-by: Eric Van Tassell <Eric.VanTassell@amd.com>
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Add support for PCIe TLP Processing Hints (TPH) support (see PCIe r6.2,
sec 6.17).
Add TPH register definitions in pci_regs.h, including the TPH Requester
capability register, TPH Requester control register, TPH Completer
capability, and the ST fields of MSI-X entry.
Introduce pcie_enable_tph() and pcie_disable_tph(), enabling drivers to
toggle TPH support and configure specific ST mode as needed. Also add a new
kernel parameter, "pci=notph", allowing users to disable TPH support across
the entire system.
Link: https://lore.kernel.org/r/20241002165954.128085-2-wei.huang2@amd.com
Co-developed-by: Jing Liu <jing2.liu@intel.com>
Co-developed-by: Paul Luse <paul.e.luse@linux.intel.com>
Co-developed-by: Eric Van Tassell <Eric.VanTassell@amd.com>
Signed-off-by: Jing Liu <jing2.liu@intel.com>
Signed-off-by: Paul Luse <paul.e.luse@linux.intel.com>
Signed-off-by: Eric Van Tassell <Eric.VanTassell@amd.com>
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
pci_hp_deregister() was converted to void by the commit 51bbf9bee3 ("PCI:
hotplug: Demidlayer registration with the core") but its kerneldoc still
describes the return value. pci_hp_del() and pci_hp_destroy() have been
void since they were introduced in that same commit.
Remove the return value description from the kerneldoc of those functions.
Link: https://lore.kernel.org/r/20240930124436.17908-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reorganize kerneldoc parameter names to match the parameter order in the
function header.
Problems identified using Coccinelle.
Link: https://lore.kernel.org/r/20240930112121.95324-23-Julia.Lawall@inria.fr
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----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=L3s9
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Wait for device readiness after reset by polling Vendor ID and
looking for Configuration RRS instead of polling the Command
register and looking for non-error completions, to avoid hardware
retries done for RRS on non-Vendor ID reads (Bjorn Helgaas)
- Rename CRS Completion Status to RRS ('Request Retry Status') to
match PCIe r6.0 spec usage (Bjorn Helgaas)
- Clear LBMS bit after a manual link retrain so we don't try to
retrain a link when there's no downstream device anymore (Maciej W.
Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance
to use higher speeds (Maciej W. Rozycki)
- Wait for each level of downstream bus, not just the first, to
become accessible before restoring devices on that bus (Ilpo
Järvinen)
- Add ARCH_PCI_DEV_GROUPS so s390 can add its own attribute_groups
without having to stomp on the core's pdev->dev.groups (Lukas
Wunner)
Driver binding:
- Export pcim_request_region(), a managed counterpart of
pci_request_region(), for use by drivers (Philipp Stanner)
- Export pcim_iomap_region() and deprecate pcim_iomap_regions()
(Philipp Stanner)
- Request the PCI BAR used by xboxvideo (Philipp Stanner)
- Request and map drm/ast BARs with pcim_iomap_region() (Philipp
Stanner)
MSI:
- Add MSI_FLAG_NO_AFFINITY flag for devices that mux MSIs onto a
single IRQ line and cannot set the affinity of each MSI to a
specific CPU core (Marek Vasut)
- Use MSI_FLAG_NO_AFFINITY and remove unnecessary .irq_set_affinity()
implementations in aardvark, altera, brcmstb, dwc, mediatek-gen3,
mediatek, mobiveil, plda, rcar, tegra, vmd, xilinx-nwl,
xilinx-xdma, and xilinx drivers to avoid 'IRQ: set affinity failed'
warnings (Marek Vasut)
Power management:
- Add pwrctl support for ATH11K inside the WCN6855 package (Konrad
Dybcio)
PCI device hotplug:
- Remove unnecessary hpc_ops struct from shpchp (ngn)
- Check for PCI_POSSIBLE_ERROR(), not 0xffffffff, in cpqphp
(weiyufeng)
Virtualization:
- Mark Creative Labs EMU20k2 INTx masking as broken (Alex Williamson)
- Add an ACS quirk for Qualcomm SA8775P, which doesn't advertise ACS
but does provide ACS-like features (Subramanian Ananthanarayanan)
IOMMU:
- Add function 0 DMA alias quirk for Glenfly Arise audio function,
which uses the function 0 Requester ID (WangYuli)
NPEM:
- Add Native PCIe Enclosure Management (NPEM) support for sysfs
control of NVMe RAID storage indicators (ok/fail/locate/
rebuild/etc) (Mariusz Tkaczyk)
- Add support for the ACPI _DSM PCIe SSD status LED management, which
is functionally similar to NPEM but mediated by platform firmware
(Mariusz Tkaczyk)
Device trees:
- Drop minItems and maxItems from ranges in PCI generic host binding
since host bridges may have several MMIO and I/O port apertures
(Frank Li)
- Add kirin, rcar-gen2, uniphier DT binding top-level constraints for
clocks (Krzysztof Kozlowski)
Altera PCIe controller driver:
- Convert altera DT bindings from text to YAML (Matthew Gerlach)
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same
thing and is what other drivers use (Jinjie Ruan)
Broadcom STB PCIe controller driver:
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller
doesn't imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
Freescale i.MX6 PCIe controller driver:
- Add imx6q-pcie 'dbi2' and 'atu' reg-names for i.MX8M Endpoints
(Richard Zhu)
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP
Endpoints to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which
is harmless for devices that implement their own internal PHY
management and don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver
Root Complex support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Replace layerscape-pcie DT binding compatible fsl,lx2160a-pcie with
fsl,lx2160ar2-pcie (Frank Li)
- Add layerscape-pcie DT binding deprecated 'num-viewport' property
to address a DT checker warning (Frank Li)
- Change layerscape-pcie DT binding 'fsl,pcie-scfg' to phandle-array
(Frank Li)
Loongson PCIe controller driver:
- Increase max PCI hosts to 8 for Loongson-3C6000 and newer chipsets
(Huacai Chen)
Marvell Aardvark PCIe controller driver:
- Fix issue with emulating Configuration RRS for two-byte reads of
Vendor ID; previously it only worked for four-byte reads (Bjorn
Helgaas)
MediaTek PCIe Gen3 controller driver:
- Add per-SoC struct mtk_gen3_pcie_pdata to support multiple SoC
types (Lorenzo Bianconi)
- Use reset_bulk APIs to manage PHY reset lines (Lorenzo Bianconi)
- Add DT and driver support for Airoha EN7581 PCIe controller
(Lorenzo Bianconi)
Qualcomm PCIe controller driver:
- Update qcom,pcie-sc7280 DT binding with eight interrupts (Rayyan
Ansari)
- Add back DT 'vddpe-3v3-supply', which was incorrectly removed
earlier (Johan Hovold)
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a
flood (Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan
Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for
endpoint controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding
(Manivannan Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't
overlap BAR MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is
deasserted to partially avoid the problem that the endpoint SoC
crashes when accessing things when Refclk is absent (Manivannan
Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank
Babu Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to
avoid a NULL pointer dereference (Manivannan Sadhasivam)
Renesas R-Car PCIe controller driver:
- Make the read-only const array 'check_addr' static (Colin Ian King)
- Add R-Car V4M (R8A779H0) PCIe host and endpoint to DT binding
(Yoshihiro Shimoda)
TI DRA7xx PCIe controller driver:
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary
handler is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe
(Siddharth Vadapalli)
TI J721E PCIe driver:
- Add DT 'ti,syscon-acspcie-proxy-ctrl' and driver support to enable
the ACSPCIE module to drive Refclk for the Endpoint (Siddharth
Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link
setup can be done separately during resume (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between
Refclk becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
TI Keystone PCIe controller driver:
- Fix NULL pointer checking when applying MRRS limitation quirk for
AM65x SR 1.0 Errata #i2037 (Dan Carpenter)
Xilinx NWL PCIe controller driver:
- Fix off-by-one error in INTx IRQ handler that caused INTx
interrupts to be lost or delivered as the wrong interrupt (Sean
Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean
Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
Xilinx XDMA PCIe controller driver:
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT
binding and xilinx-dma-pl driver (Thippeswamy Havalige)
Miscellaneous:
- Fix buffer overflow in kirin_pcie_parse_port() (Alexandra Diupina)
- Fix minor kerneldoc issues and typos (Bjorn Helgaas)
- Use PCI_DEVID() macro in aer_inject() instead of open-coding it
(Jinjie Ruan)
- Check pcie_find_root_port() return in x86 fixups to avoid NULL
pointer dereferences (Samasth Norway Ananda)
- Make pci_bus_type constant (Kunwu Chan)
- Remove unused declarations of __pci_pme_wakeup() and
pci_vpd_release() (Yue Haibing)
- Remove any leftover .*.cmd files with make clean (zhang jiao)
- Remove unused BILLION macro (zhang jiao)"
* tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (132 commits)
PCI: Fix typos
dt-bindings: PCI: qcom: Allow 'vddpe-3v3-supply' again
tools: PCI: Remove unused BILLION macro
tools: PCI: Remove .*.cmd files with make clean
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: Mark Creative Labs EMU20k2 INTx masking as broken
dt-bindings: PCI: imx6q-pcie: Add reg-name "dbi2" and "atu" for i.MX8M PCIe Endpoint
dt-bindings: PCI: altera: msi: Convert to YAML
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: Rename CRS Completion Status to RRS
PCI: aardvark: Correct Configuration RRS checking
PCI: Wait for device readiness with Configuration RRS
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
...
- Add an ACS quirk for Qualcomm SA8775P, which doesn't advertise ACS but
does provide ACS-like features (Subramanian Ananthanarayanan)
- Mark Creative Labs EMU20k2 INTx masking as broken (Alex Williamson)
* pci/quirks:
PCI: Mark Creative Labs EMU20k2 INTx masking as broken
PCI: Add ACS quirk for Qualcomm SA8775P
- Fix off-by-one error in INTx IRQ handler that caused INTx interrupts to
be lost or delivered as the wrong interrupt (Sean Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT binding
and xilinx-dma-pl driver (Thippeswamy Havalige)
* pci/controller/xilinx:
PCI: xilinx-xdma: Add Xilinx QDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx QDMA PCIe Root Port Bridge
arm64: zynqmp: Add PCIe phys property for ZCU102
PCI: xilinx-nwl: Add PHY support
dt-bindings: pci: xilinx-nwl: Add phys property
PCI: xilinx-nwl: Clean up clock on probe failure/removal
PCI: xilinx-nwl: Rate-limit misc interrupt messages
PCI: xilinx-nwl: Fix register misspelling
PCI: xilinx-nwl: Fix off-by-one in INTx IRQ handler
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a flood
(Manivannan Sadhasivam)
- Add Manivannan Sadhasivam as maintainer of qcom endpoint driver
(Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for endpoint
controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding (Manivannan
Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't overlap BAR
MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is deasserted to
partially avoid the problem that the endpoint SoC crashes when accessing
things when Refclk is absent (Manivannan Sadhasivam)
- Rename dw_pcie.link_gen to max_link_speed to avoid ambiguity (Manivannan
Sadhasivam)
- Cache maximum link speed value in dw_pcie.max_link_speed for use by
vendor drivers (Manivannan Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank Babu
Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to avoid a
NULL pointer dereference (Manivannan Sadhasivam)
* pci/controller/qcom:
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: qcom: Disable mirroring of DBI and iATU register space in BAR region
PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt
dt-bindings: PCI: qcom,pcie-sm8450: Add 'global' interrupt
PCI: qcom-ep: Modify 'global_irq' and 'perst_irq' IRQ device names
PCI: endpoint: Assign PCI domain number for endpoint controllers
dt-bindings: PCI: pci-ep: Document 'linux,pci-domain' property
dt-bindings: PCI: pci-ep: Update Maintainers
PCI: qcom-ep: Reword the error message for receiving unknown global IRQ event
PCI: qcom-ep: Drop the redundant masking of global IRQ events
- Add DT "ti,syscon-acspcie-proxy-ctrl" and driver support to enable the
ACSPCIE module to drive Refclk for the Endpoint (Siddharth Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link setup
can be done separately during resume (Thomas Richard)
- Use dev_err_probe() to simplify j721e probe (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between Refclk
becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
* pci/controller/j721e:
PCI: j721e: Add suspend and resume support
PCI: j721e: Use T_PERST_CLK_US macro
PCI: Add T_PERST_CLK_US macro
PCI: j721e: Add reset GPIO to struct j721e_pcie
PCI: j721e: Use dev_err_probe() in the probe() function
PCI: cadence: Set cdns_pcie_host_init() global
PCI: cadence: Extract link setup sequence from cdns_pcie_host_setup()
PCI: j721e: Enable ACSPCIE Refclk if "ti,syscon-acspcie-proxy-ctrl" exists
dt-bindings: PCI: ti,j721e-pci-host: Add ACSPCIE proxy control property
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP Endpoints
to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which is
harmless for devices that implement their own internal PHY management and
don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver Root
Complex support (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: imx6: Call common PHY API to set mode, speed, and submode
dt-bindings: PCI: imx6q-pcie: Add i.MX8Q PCIe compatible string
PCI: imx6: Consolidate redundant if-checks
PCI: imx6: Improve comment for workaround ERR010728
PCI: imx6: Simplify switch-case logic by involve core_reset callback
PCI: imx6: Introduce SoC specific callbacks for controlling REFCLK
PCI: imx6: Rename imx6_* with imx_*
PCI: imx6: Fix missing call to phy_power_off() in error handling
PCI: imx6: Fix i.MX8MP PCIe EP's occasional failure to trigger MSI
PCI: imx6: Fix establish link failure in EP mode for i.MX8MM and i.MX8MP
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary handler
is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe (Siddharth
Vadapalli)
* pci/controller/dra7xx:
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
- Change DT binding maintainer to Jim Quinlan (Jim Quinlan)
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Refactor .probe() error handling (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add SoC-specific HARD_DEBUG, INTR2_CPU_BASE register offsets (Jim
Quinlan)
- Drop unused RGR1_SW_INIT_1_INIT_MASK, RGR1_SW_INIT_1_INIT_SHIFT offsets
(Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller doesn't
imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Check return values of all reset_control_*() calls (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
* pci/controller/brcmstb:
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
PCI: brcmstb: Enable 7712 SoCs
PCI: brcmstb: Change field name from 'type' to 'soc_base'
PCI: brcmstb: Check return value of all reset_control_* calls
PCI: brcmstb: Refactor for chips with many regular inbound windows
PCI: brcmstb: Don't conflate the reset rescal with PHY ctrl
PCI: brcmstb: Remove two unused constants from driver
PCI: brcmstb: PCI: brcmstb: Make HARD_DEBUG, INTR2_CPU_BASE offsets SoC-specific
PCI: brcmstb: Use swinit reset if available
PCI: brcmstb: Use bridge reset if available
PCI: brcmstb: Use common error handling code in brcm_pcie_probe()
dt-bindings: PCI: brcm,stb-pcie: Add 7712 SoC description
dt-bindings: PCI: brcm,stb-pcie: Use maxItems for reset controllers
dt-bindings: PCI: brcm,stb-pcie: Change brcmstb maintainer and cleanup
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same thing
and is what other drivers use (Jinjie Ruan)
* pci/controller/altera:
PCI: altera: Replace TLP_REQ_ID() with macro PCI_DEVID()
- Add ARCH_PCI_DEV_GROUPS so s390 can add its own attribute_groups without
having to stomp on the core's pdev->dev.groups (Lukas Wunner)
* pci/sysfs:
s390/pci: Stop usurping pdev->dev.groups
- Wait for each level of downstream bus, not just the first, to become
accessible before restoring devices on that bus (Ilpo Järvinen)
* pci/reset:
PCI: Wait for Link before restoring Downstream Buses
- Initialize leds class earlier (with an unfortunate Makefile ordering
change) so the PCI NPEM driver can use it (Mariusz Tkaczyk)
- Add Native PCIe Enclosure Management (NPEM) support for sysfs control of
NVMe RAID storage indicators (ok/fail/locate/rebuild/etc) (Mariusz
Tkaczyk)
- Add support for the ACPI _DSM PCIe SSD status LED management, which is
functionally similar to NPEM but mediated by platform firmware (Mariusz
Tkaczyk)
* pci/npem:
PCI/NPEM: Add _DSM PCIe SSD status LED management
PCI/NPEM: Add Native PCIe Enclosure Management support
leds: Init leds class earlier
- Add function 0 DMA alias quirk for Glenfly Arise audio function, which
uses the function 0 Requester ID (WangYuli)
* pci/iommu:
PCI: Add function 0 DMA alias quirk for Glenfly Arise chip
- Clear LBMS bit after a manual link retrain so we don't try to retrain a
link when there's no downstream device anymore (Maciej W. Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance to use
higher speeds (Maciej W. Rozycki)
- Correct interpretation of pcie_retrain_link() return status and update it
to return 0/errno instead of true/false (Maciej W. Rozycki)
* pci/enumeration:
PCI: Use an error code with PCIe failed link retraining
PCI: Correct error reporting with PCIe failed link retraining
PCI: Revert to the original speed after PCIe failed link retraining
PCI: Clear the LBMS bit after a link retrain
- Export pcim_request_region(), a managed counterpart of
pci_request_region(), for use by drivers (Philipp Stanner)
- Request the PCI BAR used by xboxvideo (Philipp Stanner)
- Export pcim_iomap_region() and deprecate pcim_iomap_regions() (Philipp
Stanner)
- Request and map drm/ast BARs with pcim_iomap_region() (Philipp Stanner)
* pci/devres:
drm/ast: Request PCI BAR with devres
PCI: Deprecate pcim_iomap_regions() in favor of pcim_iomap_region()
drm/vboxvideo: Add PCI region request
PCI: Make pcim_request_region() a public function
- Wait for device readiness after reset by polling Vendor ID and looking
for Configuration RRS instead of polling the Command register and looking
for non-error completions (Bjorn Helgaas)
- Fix an aardvark issue with emulating Configuration RRS for two-byte reads
of Vendor ID; previously it only worked for four-byte reads (Bjorn
Helgaas)
- Rename CRS Completion Status to RRS to match spec usage (Bjorn Helgaas)
* pci/crs:
PCI: Rename CRS Completion Status to RRS
PCI: aardvark: Correct Configuration RRS checking
PCI: Wait for device readiness with Configuration RRS
Including:
- Core changes:
- Allow ATS on VF when parent device is identity mapped.
- Optimize unmap path on ARM io-pagetable implementation.
- Use of_property_present().
- ARM-SMMU changes:
- SMMUv2:
- Devicetree binding updates for Qualcomm MMU-500 implementations.
- Extend workarounds for broken Qualcomm hypervisor to avoid
touching features that are not available (e.g. 16KiB page
support, reserved context banks).
- SMMUv3:
- Support for NVIDIA's custom virtual command queue hardware.
- Fix Stage-2 stall configuration and extend tests to cover this
area.
- A bunch of driver cleanups, including simplification of the
master rbtree code.
- Plus minor cleanups and fixes across both drivers.
- Intel VT-d changes:
- Retire si_domain and convert to use static identity domain.
- Batched IOTLB/dev-IOTLB invalidation.
- Small code refactoring and cleanups.
- AMD-Vi changes:
- Cleanup and refactoring of io-pagetable code.
- Add parameter to limit the used io-pagesizes.
- Other cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEr9jSbILcajRFYWYyK/BELZcBGuMFAmboAtoACgkQK/BELZcB
GuNidQ//WOhwVQZmdS6vnU2vu//LwFE7Q7PsRYPW2QhFri1eurKo6jxMNBtgUsXu
fPTSEBM7/lhagRgb29ycrbOYoavkEnUiIMX7vRsjl9tVkqd/GKNTrMuUC+QPiBYQ
ASkStmEUW6Zvye4rWyUxiCJIFIA5wm74wSOOQ6X2Wg3WMo51njrj1DK/k2H5JenJ
RTmIA9Ynef2py38xWDd0UE/psvKrzA5uug4IP0E0v014i36cSEVrH7hjztMfd8Sc
2dUuJ8eUUtLTo1ffTcmxoTvUBjBzJOzeSQrFfaDZDgyqayt6JoSKeX1DV/nCI8kc
ftg0pe37Zr3mndgQC7wNyUO1GOmkJl+GpMFyJTG8wpnBc0tr+TDn1o6QERymcRxA
kn62n4vxxjWoRSKt3di7hNM0Uuwj8/z/cIbDSTNbSov4fDuuz0xppdcA/ewKATv0
VgmpP5OyIFZXM+mR4Vem2hZQQ3wPOsJAFVWS1ROtYQFgiimrGf+w9et8rEU4pmp5
Ve4rSmka60NLdE6i1JNqx4sRrRsdJJ55knI77nHrt0TZkbMzA/JG1UT3TbbMJTtd
v5dviMMOXLpcKQLgqlde8QWOEjT6VUw/fbU640iyzhrWAm8fWDBefrSv6JLhevQ4
fBajoaej89cd9DkkEJiSTiyGig8QkY3HFaqDo3u5g/sBBrMBZas=
=1QvI
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu updates from Joerg Roedel:
"Core changes:
- Allow ATS on VF when parent device is identity mapped
- Optimize unmap path on ARM io-pagetable implementation
- Use of_property_present()
ARM-SMMU changes:
- SMMUv2:
- Devicetree binding updates for Qualcomm MMU-500 implementations
- Extend workarounds for broken Qualcomm hypervisor to avoid
touching features that are not available (e.g. 16KiB page
support, reserved context banks)
- SMMUv3:
- Support for NVIDIA's custom virtual command queue hardware
- Fix Stage-2 stall configuration and extend tests to cover this
area
- A bunch of driver cleanups, including simplification of the
master rbtree code
- Minor cleanups and fixes across both drivers
Intel VT-d changes:
- Retire si_domain and convert to use static identity domain
- Batched IOTLB/dev-IOTLB invalidation
- Small code refactoring and cleanups
AMD-Vi changes:
- Cleanup and refactoring of io-pagetable code
- Add parameter to limit the used io-pagesizes
- Other cleanups and fixes"
* tag 'iommu-updates-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (77 commits)
dt-bindings: arm-smmu: Add compatible for QCS8300 SoC
iommu/amd: Test for PAGING domains before freeing a domain
iommu/amd: Fix argument order in amd_iommu_dev_flush_pasid_all()
iommu/amd: Add kernel parameters to limit V1 page-sizes
iommu/arm-smmu-v3: Reorganize struct arm_smmu_ctx_desc_cfg
iommu/arm-smmu-v3: Add types for each level of the CD table
iommu/arm-smmu-v3: Shrink the cdtab l1_desc array
iommu/arm-smmu-v3: Do not use devm for the cd table allocations
iommu/arm-smmu-v3: Remove strtab_base/cfg
iommu/arm-smmu-v3: Reorganize struct arm_smmu_strtab_cfg
iommu/arm-smmu-v3: Add types for each level of the 2 level stream table
iommu/arm-smmu-v3: Add arm_smmu_strtab_l1/2_idx()
iommu/arm-smmu-qcom: apply num_context_bank fixes for SDM630 / SDM660
iommu/arm-smmu-v3: Use the new rb tree helpers
dt-bindings: arm-smmu: document the support on SA8255p
iommu/tegra241-cmdqv: Do not allocate vcmdq until dma_set_mask_and_coherent
iommu/tegra241-cmdqv: Drop static at local variable
iommu/tegra241-cmdqv: Fix ioremap() error handling in probe()
iommu/amd: Do not set the D bit on AMD v2 table entries
iommu/amd: Correct the reported page sizes from the V1 table
...
- Check return value in acpi_db_convert_to_package() (Pei Xiao).
- Detect FACS and allow setting the waking vector on reduced-hardware
ACPI platforms (Jiaqing Zhao).
- Allow ACPICA to represent semaphores as integers (Adrien Destugues).
- Complete CXL 3.0 CXIMS structures support in ACPICA (Zhang Rui).
- Make ACPICA support SPCR version 4 and add RISC-V SBI Subtype to
DBG2 (Sia Jee Heng).
- Implement the Dword_PCC Resource Descriptor Macro in ACPICA (Jose
Marinho).
- Correct the typo in struct acpi_mpam_msc_node member (Punit Agrawal).
- Implement ACPI_WARNING_ONCE() and ACPI_ERROR_ONCE() and use them to
prevent a Stall() violation warning from being printed every time
this takes place (Vasily Khoruzhick).
- Allow PCC Data Type in MCTP resource (Adam Young).
- Fix memory leaks on acpi_ps_get_next_namepath()
and acpi_ps_get_next_field() failures (Armin Wolf).
- Add support for supressing leading zeros in hex strings when
converting them to integers and update integer-to-hex-string
conversions in ACPICA (Armin Wolf).
- Add support for Windows 11 22H2 _OSI string (Armin Wolf).
- Avoid warning for Dump Functions in ACPICA (Adam Lackorzynski).
- Add extended linear address mode to HMAT MSCIS in ACPICA (Dave
Jiang).
- Handle empty connection_node in iasl (Aleksandrs Vinarskis).
- Allow for more flexibility in _DSM args (Saket Dumbre).
- Setup for ACPICA release 20240827 (Saket Dumbre).
- Add ACPI device enumeration support for interrupt controller probing
including taking dependencies into account (Sunil V L).
- Implement ACPI-based interrupt controller probing on RISC-V (Sunil V L).
- Add ACPI support for AIA in riscv-intc and add ACPI support to
riscv-imsic, riscv-aplic, and sifive-plic (Sunil V L).
- Do not release locks during operation region accesses in the ACPI EC
driver (Rafael Wysocki).
- Fix up the _STR handling in the ACPI device object sysfs interface,
make it represent the device object attributes as an attribute group
and make it rely on driver core functionality for sysfs attrubute
management (Thomas Weißschuh).
- Extend error messages printed to the kernel log when acpi_evaluate_dsm()
fails to include revision and function number (David Wang).
- Add a new AMDI0015 platform device ID to the ACPi APD driver for AMD
SoCs (Shyam Sundar S K).
- Use the driver core for the async probing management in the ACPI
battery driver (Thomas Weißschuh).
- Remove redundant initalizations of a local variable to NULL from the
ACPI battery driver (Ilpo Järvinen).
- Remove unneeded check in tps68470_pmic_opregion_probe() (Aleksandr
Mishin).
- Add support for setting the EPP register through the ACPI CPPC sysfs
interface if it is in FFH (Mario Limonciello).
- Fix MASK_VAL() usage in the ACPI CPPC library (Clément Léger).
- Reduce the log level of a per-CPU message about idle states in the
ACPI processor driver (Li RongQing).
- Fix crash in exit_round_robin() in the ACPI processor aggregator
device (PAD) driver (Seiji Nishikawa).
- Add force_vendor quirk for Panasonic Toughbook CF-18 in the ACPI
backlight driver (Hans de Goede).
- Make the DMI checks related to backlight handling on Lenovo Yoga
Tab 3 X90F less strict (Hans de Goede).
- Enforce native backlight handling on Apple MacbookPro9,2 (Esther
Shimanovich).
- Add IRQ override quirks for Asus Vivobook Go E1404GAB and MECHREV
GM7XG0M, and refine the TongFang GMxXGxx quirk (Li Chen, Tamim Khan,
Werner Sembach).
- Quirk ASUS ROG M16 to default to S3 sleep (Luke D. Jones).
- Define and use symbols for device and class name lengths in the ACPI
bus type code and make the code use strscpy() instead of strcpy() in
several places (Muhammad Qasim Abdul Majeed).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAmbjJ9kSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxhfMP/3i4Nrkmf2HpiSJ/zFMSISNbAEmLSqQQ
gSo0Mmj1OHN9W9rBiIVDgJjeakyLg2IHB1sFZ9ABtU1JvO9mMchU7OlDKIt8Q8sf
VJa+q0tcA4kny5BZa47fPjZaaM6f9boVTm5WRn9T7KSLA+EGBAxE+UXQ2ibxiPCc
ZWX8obeYe78Zv2i5U8LiO4mQlB2viGEgO/5vKywmNKYVpurOMAv4zGjvDfRxK3ZQ
GXIZLUCh0inu8VomrbI5B1bpqNTxUrLoEAExKpyAyIiRYay+nyv8Vm2sSw9roe3a
C9pux4pojT0zfkmCVJmXET0982GcMSDaB0Rb1ypwbC2EdTtEoauC/HTyTixNBxBa
MnHntDe/l6Z9gLhbj8dcfB0ZVUkahqFzndWA9EBwroor2S7woZNtA3jL9VNHbM1J
kKNPQ2YCQi1ObQcftZDC9UYYx62KVvWNZCTS1+ZjnpKNH8hcEEBwMlnmE1VTYeHf
TN0vbB6QJSDu26qOyiWMCgLAR45TW/YzA3CrJi7/zGMSUyEQvHQAe5wh5H3ygbAR
GbDau0AVSvCO7lTRpqkzS6aeTLIbp1oqGwnnSXQDy30biI2FeQyg76Nq8Rgj5Lun
8+GvmkuVSjbjTXYbLqjt/gW97O/HUdygfL7hhjS10TB+3C34mQm/pwFxNYxJdFyO
mhMeKq4DdOJ+
=XHaD
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream version
20240827, add support for ACPI-based enumeration of interrupt
controllers on RISC-V along with some related irqchip updates, clean
up the ACPI device object sysfs interface, add some quirks for
backlight handling and IRQ overrides, fix assorted issues and clean up
code.
Specifics:
- Check return value in acpi_db_convert_to_package() (Pei Xiao)
- Detect FACS and allow setting the waking vector on reduced-hardware
ACPI platforms (Jiaqing Zhao)
- Allow ACPICA to represent semaphores as integers (Adrien Destugues)
- Complete CXL 3.0 CXIMS structures support in ACPICA (Zhang Rui)
- Make ACPICA support SPCR version 4 and add RISC-V SBI Subtype to
DBG2 (Sia Jee Heng)
- Implement the Dword_PCC Resource Descriptor Macro in ACPICA (Jose
Marinho)
- Correct the typo in struct acpi_mpam_msc_node member (Punit
Agrawal)
- Implement ACPI_WARNING_ONCE() and ACPI_ERROR_ONCE() and use them to
prevent a Stall() violation warning from being printed every time
this takes place (Vasily Khoruzhick)
- Allow PCC Data Type in MCTP resource (Adam Young)
- Fix memory leaks on acpi_ps_get_next_namepath() and
acpi_ps_get_next_field() failures (Armin Wolf)
- Add support for supressing leading zeros in hex strings when
converting them to integers and update integer-to-hex-string
conversions in ACPICA (Armin Wolf)
- Add support for Windows 11 22H2 _OSI string (Armin Wolf)
- Avoid warning for Dump Functions in ACPICA (Adam Lackorzynski)
- Add extended linear address mode to HMAT MSCIS in ACPICA (Dave
Jiang)
- Handle empty connection_node in iasl (Aleksandrs Vinarskis)
- Allow for more flexibility in _DSM args (Saket Dumbre)
- Setup for ACPICA release 20240827 (Saket Dumbre)
- Add ACPI device enumeration support for interrupt controller
probing including taking dependencies into account (Sunil V L)
- Implement ACPI-based interrupt controller probing on RISC-V
(Sunil V L)
- Add ACPI support for AIA in riscv-intc and add ACPI support to
riscv-imsic, riscv-aplic, and sifive-plic (Sunil V L)
- Do not release locks during operation region accesses in the ACPI
EC driver (Rafael Wysocki)
- Fix up the _STR handling in the ACPI device object sysfs interface,
make it represent the device object attributes as an attribute
group and make it rely on driver core functionality for sysfs
attrubute management (Thomas Weißschuh)
- Extend error messages printed to the kernel log when
acpi_evaluate_dsm() fails to include revision and function number
(David Wang)
- Add a new AMDI0015 platform device ID to the ACPi APD driver for
AMD SoCs (Shyam Sundar S K)
- Use the driver core for the async probing management in the ACPI
battery driver (Thomas Weißschuh)
- Remove redundant initalizations of a local variable to NULL from
the ACPI battery driver (Ilpo Järvinen)
- Remove unneeded check in tps68470_pmic_opregion_probe() (Aleksandr
Mishin)
- Add support for setting the EPP register through the ACPI CPPC
sysfs interface if it is in FFH (Mario Limonciello)
- Fix MASK_VAL() usage in the ACPI CPPC library (Clément Léger)
- Reduce the log level of a per-CPU message about idle states in the
ACPI processor driver (Li RongQing)
- Fix crash in exit_round_robin() in the ACPI processor aggregator
device (PAD) driver (Seiji Nishikawa)
- Add force_vendor quirk for Panasonic Toughbook CF-18 in the ACPI
backlight driver (Hans de Goede)
- Make the DMI checks related to backlight handling on Lenovo Yoga
Tab 3 X90F less strict (Hans de Goede)
- Enforce native backlight handling on Apple MacbookPro9,2 (Esther
Shimanovich)
- Add IRQ override quirks for Asus Vivobook Go E1404GAB and MECHREV
GM7XG0M, and refine the TongFang GMxXGxx quirk (Li Chen, Tamim
Khan, Werner Sembach)
- Quirk ASUS ROG M16 to default to S3 sleep (Luke D. Jones)
- Define and use symbols for device and class name lengths in the
ACPI bus type code and make the code use strscpy() instead of
strcpy() in several places (Muhammad Qasim Abdul Majeed)"
* tag 'acpi-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (70 commits)
ACPI: resource: Add another DMI match for the TongFang GMxXGxx
ACPI: CPPC: Add support for setting EPP register in FFH
ACPI: PM: Quirk ASUS ROG M16 to default to S3 sleep
ACPI: video: Add force_vendor quirk for Panasonic Toughbook CF-18
ACPI: battery: use driver core managed async probing
ACPI: button: Use strscpy() instead of strcpy()
ACPI: resource: Skip IRQ override on Asus Vivobook Go E1404GAB
ACPI: CPPC: Fix MASK_VAL() usage
irqchip/sifive-plic: Add ACPI support
ACPICA: Setup for ACPICA release 20240827
ACPICA: Allow for more flexibility in _DSM args
ACPICA: iasl: handle empty connection_node
ACPICA: HMAT: Add extended linear address mode to MSCIS
ACPICA: Avoid warning for Dump Functions
ACPICA: Add support for Windows 11 22H2 _OSI string
ACPICA: Update integer-to-hex-string conversions
ACPICA: Add support for supressing leading zeros in hex strings
ACPICA: Allow for supressing leading zeros when using acpi_ex_convert_to_ascii()
ACPICA: Fix memory leak if acpi_ps_get_next_field() fails
ACPICA: Fix memory leak if acpi_ps_get_next_namepath() fails
...
The pci_bus_release_domain_nr() API is supposed to free the domain
number allocated by pci_bus_find_domain_nr(). Most of the callers of
pci_bus_find_domain_nr(), store the domain number in pci_bus::domain_nr.
As such, the pci_bus_release_domain_nr() implicitly frees the domain
number by dereferencing 'struct pci_bus'. However, one of the callers
of this API, the PCI endpoint subsystem, doesn't have 'struct pci_bus',
so it only passes NULL. Due to this, the API will end up dereferencing
the NULL pointer.
To fix this issue, pass the domain number to this API explicitly. Since
'struct pci_bus' is not used for anything else other than extracting the
domain number, it makes sense to pass the domain number directly.
Fixes: 0328947c50 ("PCI: endpoint: Assign PCI domain number for endpoint controllers")
Closes: https://lore.kernel.org/linux-pci/c0c40ddb-bf64-4b22-9dd1-8dbb18aa2813@stanley.mountain
Link: https://lore.kernel.org/linux-pci/20240912053025.25314-1-manivannan.sadhasivam@linaro.org
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Commit d4c7d1a089 ("PCI: dwc: dra7xx: Push request_irq()
call to the bottom of probe") moved the IRQ request for
"dra7xx-pcie-main" towards the end of dra7xx_pcie_probe().
However, the error handling does not take into account the
initialization performed by either dra7xx_add_pcie_port() or
dra7xx_add_pcie_ep(), depending on the mode of operation.
Fix the error handling to address this.
Fixes: d4c7d1a089 ("PCI: dwc: dra7xx: Push request_irq() call to the bottom of probe")
Link: https://lore.kernel.org/linux-pci/20240827122422.985547-3-s-vadapalli@ti.com
Tested-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Commit da87d35a6e ("PCI: dra7xx: Use threaded IRQ handler for
"dra7xx-pcie-main" IRQ") switched from devm_request_irq() to
devm_request_threaded_irq() for the "dra7xx-pcie-main" interrupt.
Since the primary handler was set to NULL, the "IRQF_ONESHOT" flag
should have also been set. Fix this.
Fixes: da87d35a6e ("PCI: dra7xx: Use threaded IRQ handler for "dra7xx-pcie-main" IRQ")
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/linux-pci/20240827122422.985547-2-s-vadapalli@ti.com
Reported-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
-----BEGIN PGP SIGNATURE-----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=i+4X
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.11-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fix from Bjorn Helgaas:
- Prevent a possible deadlock (reported by lockdep) when a driver
relinquishes a pci_dev, another driver claims it, and one uses
managed pcim_enable_device() and the other doesn't (Philipp Stanner)
* tag 'pci-v6.11-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: Fix potential deadlock in pcim_intx()
Add RX lane margining settings for 16.0 GT/s (GEN 4) data rate.
These settings improve link stability while operating at high date
rates and helps to improve signal quality.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-4-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
During high data transmission rates such as 16.0 GT/s, there is an
increased risk of signal loss due to poor channel quality and
interference. This can impact receiver's ability to capture signals
accurately.
Hence, as signal compensation is achieved through appropriate lane
equalization, apply lane equalization settings at both transmitter
and receiver which results in an increase in the PCIe signal strength.
While at it, modify the pcie-tegra194 driver to make use of the
common GEN3_EQ_CONTROL_OFF definitions in pcie-designware.h.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-3-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the dw_pcie::max_link_speed has a valid value only if the
controller driver restricts the maximum link speed in the driver or if
the platform does so in the devicetree using the 'max-link-speed'
property.
But having the maximum supported link speed of the platform would be
helpful for the vendor drivers to configure any link specific settings.
So in the case of non-valid value in dw_pcie::max_link_speed, just cache
the hardware default value from Link Capability register.
While at it, remove the 'max_link_speed' argument to the
dw_pcie_link_set_max_speed() function since the value can be
retrieved within the function.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-2-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
The 'link_gen' field is now holding the maximum supported link speed set
either by the controller driver or by DT through 'max-link-speed'
property.
However, the name 'link_gen' sounds like the negotiated link speed of
the PCIe link.
So rename it to 'max_link_speed' to make it clear that it holds the
maximum supported link speed of the controller.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-1-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
qcom_pcie_enable_resources() is called by qcom_pcie_ep_probe() and it
enables the controller resources like clocks, regulator, PHY. On one of the
new unreleased Qcom SoC, PHY enablement depends on the active refclk. And
on all of the supported Qcom endpoint SoCs, refclk comes from the host
(RC). So calling qcom_pcie_enable_resources() without refclk causes the
NoC (Network On Chip) error in the endpoint SoC and in turn results in a
whole SoC crash and rebooting into EDL (Emergency Download) mode which is
an unrecoverable state.
But qcom_pcie_enable_resources() is already called by
qcom_pcie_perst_deassert() when PERST# is deasserted, and refclk is
available at that time.
Hence, remove the unnecessary call to qcom_pcie_enable_resources() from
qcom_pcie_ep_probe() to prevent the above mentioned crash.
It should be noted that this commit prevents the crash only under normal
working condition (booting endpoint before host), but the crash may also
occur if PERST# assert happens at the wrong time. For avoiding the crash
completely, it is recommended to use SRIS mode which allows the endpoint
SoC to generate its own refclk. The driver is not supporting SRIS mode
currently, but will be added in the future.
Fixes: 869bc52534 ("PCI: dwc: ep: Fix DBI access failure for drivers requiring refclk from host")
Link: https://lore.kernel.org/linux-pci/20240830082319.51387-1-manivannan.sadhasivam@linaro.org
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
25216afc9d ("PCI: Add managed pcim_intx()") moved the allocation step for
pci_intx()'s device resource from pcim_enable_device() to pcim_intx(). As
before, pcim_enable_device() sets pci_dev.is_managed to true; and it is
never set to false again.
Due to the lifecycle of a struct pci_dev, it can happen that a second
driver obtains the same pci_dev after a first driver ran. If one driver
uses pcim_enable_device() and the other doesn't, this causes the other
driver to run into managed pcim_intx(), which will try to allocate when
called for the first time.
Allocations might sleep, so calling pci_intx() while holding spinlocks
becomes then invalid, which causes lockdep warnings and could cause
deadlocks:
========================================================
WARNING: possible irq lock inversion dependency detected
6.11.0-rc6+ #59 Tainted: G W
--------------------------------------------------------
CPU 0/KVM/1537 just changed the state of lock:
ffffa0f0cff965f0 (&vdev->irqlock){-...}-{2:2}, at:
vfio_intx_handler+0x21/0xd0 [vfio_pci_core] but this lock took another,
HARDIRQ-unsafe lock in the past: (fs_reclaim){+.+.}-{0:0}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(fs_reclaim);
local_irq_disable();
lock(&vdev->irqlock);
lock(fs_reclaim);
<Interrupt>
lock(&vdev->irqlock);
*** DEADLOCK ***
Have pcim_enable_device()'s release function, pcim_disable_device(), set
pci_dev.is_managed to false so that subsequent drivers using the same
struct pci_dev do not implicitly run into managed code.
Link: https://lore.kernel.org/r/20240905072556.11375-2-pstanner@redhat.com
Fixes: 25216afc9d ("PCI: Add managed pcim_intx()")
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Closes: https://lore.kernel.org/all/20240903094431.63551744.alex.williamson@redhat.com/
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Merge ACPI and irqchip updates related to external interrupt controller
support on RISC-V:
- Add ACPI device enumeration support for interrupt controller probing
including taking dependencies into account (Sunil V L).
- Implement ACPI-based interrupt controller probing on RISC-V (Sunil V L).
- Add ACPI support for AIA in riscv-intc and add ACPI support to
riscv-imsic, riscv-aplic, and sifive-plic (Sunil V L).
* acpi-riscv:
irqchip/sifive-plic: Add ACPI support
irqchip/riscv-aplic: Add ACPI support
irqchip/riscv-imsic: Add ACPI support
irqchip/riscv-imsic-state: Create separate function for DT
irqchip/riscv-intc: Add ACPI support for AIA
ACPI: RISC-V: Implement function to add implicit dependencies
ACPI: RISC-V: Initialize GSI mapping structures
ACPI: RISC-V: Implement function to reorder irqchip probe entries
ACPI: RISC-V: Implement PCI related functionality
ACPI: pci_link: Clear the dependencies after probe
ACPI: bus: Add RINTC IRQ model for RISC-V
ACPI: scan: Define weak function to populate dependencies
ACPI: scan: Add RISC-V interrupt controllers to honor list
ACPI: scan: Refactor dependency creation
ACPI: bus: Add acpi_riscv_init() function
ACPI: scan: Add a weak arch_sort_irqchip_probe() to order the IRQCHIP probe
arm64: PCI: Migrate ACPI related functions to pci-acpi.c
Implement i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) PCIe Root Complex
(RC) support. While the controller resembles that of i.MX8MP, the PHY
differs significantly. Also, there's a distinction between PCI bus
addresses and CPU addresses.
Introduce IMX_PCIE_FLAG_CPU_ADDR_FIXUP in drvdata::flags to indicate driver
need the cpu_addr_fixup() callback to facilitate CPU address to PCI bus
address conversion according to "ranges" property.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-11-b68ee5ef2b4d@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: check resource_list_first_type() for NULL]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
PCIe r6.0 changed the abbreviation for "Configuration Request Retry Status"
Completion Status from "CRS" to "RRS" and uses the terminology of
"Configuration RRS Software Visibility" instead of "CRS Software
Visibility".
Align the Linux usage with the r6.0 spec language. No functional change
intended.
It's confusing to make this change, but I think "RRS" *is* a better
abbreviation because it was easy to interpret "CRS" as "Completion Retry
Status", which really didn't make any sense.
Link: https://lore.kernel.org/r/20240827234848.4429-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r6.0, sec 2.3.2, when a Root Complex handles a Completion with
Request Retry Status for a Configuration Read Request that includes both
bytes of the Vendor ID field, it must complete the Request to the host by
returning 0001h for the Vendor ID and all 1's for any additional bytes.
Previously we only returned the 0001h Vendor ID value if we got an RRS
completion for reads of exactly 4 bytes. A read of 2 bytes would not
qualify, although the spec says it should.
Check for reads of 2 or more bytes including the Vendor ID.
I don't think this will fix any observable problems because RRS only
applies to the first config reads after reset, and those are all currently
dword (4-byte) reads.
Link: https://lore.kernel.org/r/20240827234848.4429-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
After a device reset, delays are required before the device can
successfully complete config accesses. PCIe r6.0, sec 6.6, specifies some
delays required before software can perform config accesses. Devices that
require more time after those delays may respond to config accesses with
Configuration Request Retry Status (RRS) completions.
Callers of pci_dev_wait() are responsible for delays until the device can
respond to config accesses. pci_dev_wait() waits any additional time until
the device can successfully complete config accesses.
Reading config space of devices that are not present or not ready typically
returns ~0 (PCI_ERROR_RESPONSE). Previously we polled the Command register
until we got a value other than ~0. This is sometimes a problem because
Root Complex handling of RRS completions may include several retries and
implementation-specific behavior that is invisible to software (see sec
2.3.2), so the exponential backoff in pci_dev_wait() may not work as
intended.
Linux enables Configuration RRS Software Visibility on all Root Ports that
support it. If it is enabled, read the Vendor ID instead of the Command
register. RRS completions cause immediate return of the 0x0001 reserved
Vendor ID value, so the pci_dev_wait() backoff works correctly.
When a read of Vendor ID eventually completes successfully by returning a
non-0x0001 value (the Vendor ID or 0xffff for VFs), the device should be
initialized and ready to respond to config requests.
For conventional PCI devices or devices below Root Ports that don't support
Configuration RRS Software Visibility, poll the Command register as before.
This was developed independently, but is very similar to Stanislav
Spassov's previous work at
https://lore.kernel.org/linux-pci/20200223122057.6504-1-stanspas@amazon.com
Link: https://lore.kernel.org/r/20240827234848.4429-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Duc Dang <ducdang@google.com>
Sort enum pcie_soc_base values.
Rename pcie_offsets_bmips_7425[] to pcie_offsets_bcm7425[] to match BCM7425
pcie_soc_base enum, bcm7425_cfg, and "brcm,bcm7425-pcie" .compatible
string.
Rename pcie_offset_bcm7278[] to pcie_offsets_bcm7278[] to match other
"pcie_offsets" names.
Rename pcie_offset_bcm7712[] to pcie_offsets_bcm7712[] to match other
"pcie_offsets" names.
Sort pcie_offsets_*[] by SoC name, move them all together, indent values
for easy reading.
Sort pcie_cfg_data structs by SoC name.
Sort .compatible strings by SoC name.
No functional change intended.
Link: https://lore.kernel.org/r/20240902205456.227409-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Invoke the common PHY API to configure mode, speed, and submode. While
these functions are optional in the PHY interface, they are necessary for
certain PHY drivers. Lack of support for these functions in a PHY driver
does not cause harm.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-10-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Consolidated redundant if-checks pertaining to imx_pcie->phy. Instead of
two separate checks, merged them into one to improve code readability.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-8-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Instead of using the switch case statement to assert/dassert the core
reset handled by this driver itself, let's introduce a new callback
core_reset() and define it for platforms that require it.
This simplifies the code.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-5-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Instead of using the switch case statement to enable/disable the
reference clock handled by this driver itself, let's introduce a new
callback enable_ref_clk() and define it for platforms that require it.
This simplifies the code.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-5-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Since this driver has evolved to support other i.MX SoCs such as
i.MX7/8/9, thus rename the 'imx6' prefix to 'imx' to avoid confusion.
The driver name is left unchanged to avoid breaking userspace.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-3-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log, refactor the IMX_* macros]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Fix missing call to phy_power_off() in the error path of
imx6_pcie_host_init(). Remove unnecessary check for imx6_pcie->phy
as the PHY API already handles NULL pointers.
Fixes: cbcf8722b5 ("phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()")
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-3-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.1+
Correct occasional MSI triggering failures in i.MX8MP PCIe EP by applying
the correct hardware outbound alignment requirement.
The i.MX platform has a restriction about outbound address translation. The
pci-epc-mem uses page_size to manage it. Set the correct page_size for i.MX
platform to meet the hardware requirement, which is the same as inbound
address alignment.
Thus, align it with epc_features::align.
Fixes: 1bd0d43dcf ("PCI: imx6: Clean up addr_space retrieval code")
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-2-b68ee5ef2b4d@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Cc: <stable@vger.kernel.org> # 6.9+
Add IMX6_PCIE_FLAG_HAS_APP_RESET flag to IMX8MM_EP and IMX8MP_EP drvdata.
This flag was overlooked during code restructuring. It is crucial to
release the app-reset from the System Reset Controller before initiating
LTSSM to rectify the issue.
Fixes: 0c9651c21f ("PCI: imx6: Simplify reset handling by using *_FLAG_HAS_*_RESET")
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-1-b68ee5ef2b4d@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.9+
Given how the call place in pcie_wait_for_link_delay() got structured now,
and that pcie_retrain_link() returns a potentially useful error code,
convert pcie_failed_link_retrain() to return an error code rather than a
boolean status, fixing handling at the call site mentioned. Update the
other call site accordingly.
Fixes: 1abb473903 ("Merge branch 'pci/enumeration'")
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2408091156530.61955@angie.orcam.me.uk
Reported-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/aa2d1c4e-9961-d54a-00c7-ddf8e858a9b0@linux.intel.com/
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v6.5+
Only return successful completion status from pcie_failed_link_retrain() if
retraining has actually been done, preventing excessive delays from being
triggered at call sites in a hope that communication will finally be
established with the downstream device where in fact nothing has been done
about the link in question that would justify such a hope.
Fixes: a89c82249c ("PCI: Work around PCIe link training failures")
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2408091133260.61955@angie.orcam.me.uk
Reported-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/aa2d1c4e-9961-d54a-00c7-ddf8e858a9b0@linux.intel.com/
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v6.5+
When `pcie_failed_link_retrain' has failed to retrain the link by hand
it leaves the link speed restricted to 2.5GT/s, which will then affect
any device that has been plugged in later on, which may not suffer from
the problem that caused the speed restriction to have been attempted.
Consequently such a downstream device will suffer from an unnecessary
communication throughput limitation and therefore performance loss.
Remove the speed restriction then and revert the Link Control 2 register
to its original state if link retraining with the speed restriction in
place has failed. Retrain the link again afterwards so as to remove any
residual state, waiting on LT rather than DLLLA to avoid an excessive
delay and ignoring the result as this training is supposed to fail
anyway.
Fixes: a89c82249c ("PCI: Work around PCIe link training failures")
Link: https://lore.kernel.org/linux-pci/alpine.DEB.2.21.2408251412590.30766@angie.orcam.me.uk
Reported-by: Matthew W Carlis <mattc@purestorage.com>
Link: https://lore.kernel.org/r/20240806000659.30859-1-mattc@purestorage.com/
Link: https://lore.kernel.org/r/20240722193407.23255-1-mattc@purestorage.com/
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v6.5+
The LBMS bit, where implemented, is set by hardware either in response
to the completion of retraining caused by writing 1 to the Retrain Link
bit or whenever hardware has changed the link speed or width in attempt
to correct unreliable link operation. It is never cleared by hardware
other than by software writing 1 to the bit position in the Link Status
register and we never do such a write.
We currently have two places, namely apply_bad_link_workaround() and
pcie_failed_link_retrain() in drivers/pci/controller/dwc/pcie-tegra194.c
and drivers/pci/quirks.c respectively where we check the state of the LBMS
bit and neither is interested in the state of the bit resulting from the
completion of retraining, both check for a link fault.
And in particular pcie_failed_link_retrain() causes issues consequently, by
trying to retrain a link where there's no downstream device anymore and the
state of 1 in the LBMS bit has been retained from when there was a device
downstream that has since been removed.
Clear the LBMS bit then at the conclusion of pcie_retrain_link(), so that
we have a single place that controls it and that our code can track link
speed or width changes resulting from unreliable link operation.
Fixes: a89c82249c ("PCI: Work around PCIe link training failures")
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2408091133140.61955@angie.orcam.me.uk
Reported-by: Matthew W Carlis <mattc@purestorage.com>
Link: https://lore.kernel.org/r/20240806000659.30859-1-mattc@purestorage.com/
Link: https://lore.kernel.org/r/20240722193407.23255-1-mattc@purestorage.com/
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: <stable@vger.kernel.org> # v6.5+
The Broadcom STB 7712 is the sibling chip of the RPi 5 (2712). It has
one PCIe controller with a single port, supports gen2 and one lane only.
The current revision of the chip is "C0" or "C1".
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-14-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
The 'type' field used in the driver to discern SoC differences is
confusing; change it to the more apt 'soc_base'.
The 'base' is because some SoCs have the same characteristics as
previous SoCs so it is convenient to classify them in the same group.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-13-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Always check the return value for invocations of reset_control_xxx() and
propagate the error to the next level.
Although the current functions in reset-brcmstb.c cannot fail, this may
someday change.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-12-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Provide support for new chips with multiple inbound windows while
keeping the legacy support for the older chips.
In existing chips there are three inbound windows with fixed purposes:
the first was for mapping SoC internal registers, the second was for
memory, and the third was for memory but with the endian swapped.
Typically, only one window was used.
Complicating the inbound window usage was the fact that the PCIe HW
would do a baroque internal mapping of system memory, and concatenate
the regions of multiple memory controllers.
Newer chips such as the 7712 and Cable Modem SoCs take a step forward
and drop the internal mapping while providing for multiple inbound
windows. This works in concert with the dma-ranges property, where each
provided range becomes an inbound window.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-11-james.quinlan@broadcom.com
Co-developed-by: Riyan Dhiman <riyandhiman14@gmail.com>
Signed-off-by: Riyan Dhiman <riyandhiman14@gmail.com>
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log, wrap code comments to 80 columns]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-----BEGIN PGP SIGNATURE-----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=JNeL
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.11-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Unregister platform devices for child nodes when stopping a PCI
device, even if the PCI core has already cleared the OF_POPULATED bit
and of_platform_depopulate() doesn't do anything (Bartosz
Golaszewski)
- Rescan the bus from a separate thread so we don't deadlock when
triggering rescan from sysfs (Bartosz Golaszewski)
* tag 'pci-v6.11-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/pwrctl: Rescan bus on a separate thread
PCI: Don't rely on of_platform_depopulate() for reused OF-nodes
The PCIe SSD Status LED Management _DSM defined in PCI Firmware Spec r3.3
sec 4.7 provides a way to manage LEDs via ACPI.
The design is similar to NPEM defined in PCIe Base Specification r6.1 sec
6.28:
- Both standards are indication oriented,
- _DSM supported bits correspond to NPEM capability register bits,
- _DSM control bits correspond to NPEM control register bits.
_DSM does not support enclosure-specific indications or the special NPEM
commands NPEM_ENABLE and NPEM_RESET.
_DSM is implemented as a second backend in NPEM driver. The backend used is
logged with info priority. The same sysfs interface is used for both NPEM
and _DSM.
According to spec, _DSM has higher priority, and availability of _DSM in
not limited to devices with NPEM support.
The Dell implementation of DSM uses acpi ipmi, which may not be available
immediately (in fact it may take up to 10s for this interface to be
available). It can determine if DSM is supported (GET_SUPPORTED_STATES_DSM
is working) but it cannot serve GET_STATE_DSM or SET_STATE_DSM commands in
this time.
From userspace application perspective (primarily configured by systemd
service) it is better to have not working but configured interface rather
than have it available after few seconds.
For that reason, npem->active_indications cache is now loaded lazily, i.e.
any GET or SET request want cache to be updated if it is not done yet.
Link: https://lore.kernel.org/r/20240904104848.23480-4-mariusz.tkaczyk@linux.intel.com
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The Qualcomm SA8775P root ports don't advertise an ACS capability, but they
do provide ACS-like features to disable peer transactions and validate bus
numbers in requests.
Thus, add an ACS quirk for the SA8775P.
Link: https://lore.kernel.org/linux-pci/20240906052228.1829485-1-quic_skananth@quicinc.com
Signed-off-by: Subramanian Ananthanarayanan <quic_skananth@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Within kirin_pcie_parse_port(), the pcie->num_slots is compared to
pcie->gpio_id_reset size (MAX_PCI_SLOTS) which is correct and would lead
to an overflow.
Thus, fix condition to pcie->num_slots + 1 >= MAX_PCI_SLOTS and move
pcie->num_slots increment below the if-statement to avoid out-of-bounds
array access.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: b22dbbb245 ("PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge")
Link: https://lore.kernel.org/linux-pci/20240903115823.30647-1-adiupina@astralinux.ru
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The TLP_REQ_ID's function is same as current PCI_DEVID()
macro, replace it.
No functional changes intended.
Link: https://lore.kernel.org/linux-pci/20240828104202.3683491-1-ruanjinjie@huawei.com
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Native PCIe Enclosure Management (NPEM, PCIe r6.1 sec 6.28) allows managing
LEDs in storage enclosures. NPEM is indication oriented and it does not
give direct access to LEDs. Although each indication *could* represent an
individual LED, multiple indications could also be represented as a single,
multi-color LED or a single LED blinking in a specific interval. The
specification leaves that open.
Each enabled indication (capability register bit on) is represented as a
ledclass_dev which can be controlled through sysfs. For every ledclass
device only 2 brightness states are allowed: LED_ON (1) or LED_OFF (0).
This corresponds to the NPEM control register (Indication bit on/off).
Ledclass devices appear in sysfs as child devices (subdirectory) of PCI
device which has an NPEM Extended Capability and indication is enabled in
NPEM capability register. For example, these are LEDs created for pcieport
"10000:02:05.0" on my setup:
leds/
├── 10000:02:05.0:enclosure:fail
├── 10000:02:05.0:enclosure:locate
├── 10000:02:05.0:enclosure:ok
└── 10000:02:05.0:enclosure:rebuild
They can be also found in "/sys/class/leds" directory. The parent PCIe
device domain/bus/device/function address is used to guarantee uniqueness
across leds subsystem.
To enable/disable a "fail" indication, the "brightness" file can be edited:
echo 1 > ./leds/10000:02:05.0:enclosure:fail/brightness
echo 0 > ./leds/10000:02:05.0:enclosure:fail/brightness
PCIe r6.1, sec 7.9.19.2 defines the possible indications.
Multiple indications for same parent PCIe device can conflict and hardware
may update them when processing new request. To avoid issues, driver
refresh all indications by reading back control register.
This driver expects to be the exclusive NPEM extended capability manager.
It waits up to 1 second after imposing new request, it doesn't verify if
controller is busy before write, and it assumes the mutex lock gives
protection from concurrent updates.
If _DSM LED management is available, we assume the platform may be using
NPEM for its own purposes (see PCI Firmware Spec r3.3 sec 4.7), so the
driver does not use NPEM. A future patch will add _DSM support; an info
message notes whether NPEM or _DSM is being used.
NPEM is a PCIe extended capability so it should be registered in
pcie_init_capabilities() but it is not possible due to LED dependency. The
parent pci_device must be added earlier for led_classdev_register() to be
successful. NPEM does not require configuration on kernel side, so it is
safe to register LED devices later.
Link: https://lore.kernel.org/r/20240904104848.23480-3-mariusz.tkaczyk@linux.intel.com
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add suspend and resume support. Only the Root Complex mode is supported.
During the suspend stage PERST# is asserted, then deasserted during the
resume stage.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-7-a2f9156da6c3@bootlin.com
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
[kwilczynski: commit log, update references to the PCI SIG specification]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The "Power Sequencing and Reset Signal Timings" table of the PCI
Express Card Electromechanical Specification, Revision 5.1, Section
2.9.2, indicates PERST# should be deasserted after minimum of 100us
once REFCLK is stable (symbol T_PERST-CLK).
Add a macro so that PCIe controller drivers can use it.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-5-a2f9156da6c3@bootlin.com
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
[kwilczynski: commit log, update sleep interval macros code comments]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add a "has_phy" field indicating that the internal PHY has SW control
that requires configuration. Some previous chips only required the
firing of the "rescal" reset controller.
This change requires us to give the 7216 SoC its own cfg_data structure.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-10-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Remove two constants in the driver which are no longer
used: RGR1_SW_INIT_1_INIT_MASK and RGR1_SW_INIT_1_INIT_SHIFT.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-9-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Do preparatory work for the 7712 SoC, which is introduced in a
future commit.
Our HW design has changed two register offsets for the 7712, where
previously it was a common value for all Broadcom SoCs with PCIe
cores.
Specifically, the two offsets are to the registers HARD_DEBUG and
INTR2_CPU_BASE.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-8-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
The 7712 SoC adds a software init reset device for the PCIe HW.
If found in the DT node, use it.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-7-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The 7712 SoC has a bridge reset which can be described in the device
tree.
Use it if present. Otherwise, continue to use the legacy method to
reset the bridge.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-6-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log, refactored function brcm_pcie_bridge_sw_init_set_generic()]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Refactor the error handling in the bottom half of the probe function
for readability.
The invocation of clk_prepare_enable() is moved lower in the function
and this simplifies a couple of return paths. The dev_err_probe() is
also used when it is apt.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-5-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If we trigger the bus rescan from sysfs, we'll try to lock the PCI rescan
mutex recursively and deadlock - the platform device will be populated and
probed on the same thread that handles the sysfs write.
Add a workqueue to the pwrctl code on which we schedule the rescan for
controlled PCI devices. While at it: add a new interface for initializing
the pwrctl context where we'd now assign the parent device address and
initialize the workqueue.
Link: https://lore.kernel.org/r/20240823093323.33450-3-brgl@bgdev.pl
Fixes: 4565d2652a ("PCI/pwrctl: Add PCI power control core code")
Reported-by: Konrad Dybcio <konradybcio@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
of_platform_depopulate() doesn't play nicely with reused OF nodes - it
ignores the ones that are not marked explicitly as populated and it may
happen that the PCI device goes away before the platform device in which
case the PCI core clears the OF_POPULATED bit.
Unconditionally unregister the platform devices for child nodes when
stopping the PCI device.
Link: https://lore.kernel.org/r/20240823093323.33450-2-brgl@bgdev.pl
Fixes: 8fb18619d9 ("PCI/pwrctl: Create platform devices for child OF nodes of the port node")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Struct cdns_pcie_rc once had a .dev member, but it was removed by
bd22885aa1 ("PCI: cadence: Refactor driver to use as a core library").
Drop the extra kerneldoc for it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Struct mtk_pcie.mem was removed by 8a26f861b8 ("PCI: mediatek: Use
pci_parse_request_of_pci_ranges()"), but the kerneldoc was left. Remove
the extra kerneldoc.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add reset GPIO to struct j721e_pcie, so it can be used at suspend and
resume stages.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-4-a2f9156da6c3@bootlin.com
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Use dev_err_probe() instead of dev_err() in the probe() function to
simplify the code and standardize the error output.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-3-a2f9156da6c3@bootlin.com
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
During the resume sequence of the host, cdns_pcie_host_init() needs to be
called, so set it global.
The dev function parameter is removed, as it isn't used.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-2-a2f9156da6c3@bootlin.com
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The function cdns_pcie_host_setup() mixes probe structure and link setup.
The link setup must be done during the resume sequence. So extract it from
cdns_pcie_host_setup() and create a dedicated function.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-1-a2f9156da6c3@bootlin.com
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Introduce support for Airoha EN7581 PCIe controller to mediatek-gen3
PCIe controller driver.
Link: https://lore.kernel.org/linux-pci/aca00bd672ee576ad96d279414fc0835ff31f637.1720022580.git.lorenzo@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Zhengping Zhang <zhengping.zhang@airoha.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Use reset_bulk APIs to manage PHY reset lines.
This is a preliminary patch in order to add Airoha EN7581 PCIe support.
Link: https://lore.kernel.org/linux-pci/3ceb83bc0defbcf868521f8df4b9100e55ec2614.1720022580.git.lorenzo@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Zhengping Zhang <zhengping.zhang@airoha.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Introduce mtk_gen3_pcie_pdata data structure in order to define
multiple callbacks for each supported SoC.
This is a preliminary patch to introduce EN7581 PCIe support.
Link: https://lore.kernel.org/linux-pci/c193d1a87505d045e2e0ef33317bce17012ee095.1720022580.git.lorenzo@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Zhengping Zhang <zhengping.zhang@airoha.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Don't populate the const read-only array check_addr on the stack at
run time, instead make it static.
Link: https://lore.kernel.org/linux-pci/20240822205941.643187-1-colin.i.king@gmail.com
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
[kwilczynski: refactor array definition]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The code in vmd_shutdown() had an indentation issue where spaces were
used instead of tabs. This commit corrects the indentation to use tabs,
adhering to the Linux kernel coding style guidelines.
Issue reported by the checkpatch.pl script:
ERROR: code indent should use tabs where possible
#1056: FILE: drivers/pci/controller/vmd.c:1056:
+ struct vmd_dev *vmd = pci_get_drvdata(dev);$
WARNING: please, no spaces at the start of a line
#1056: FILE: drivers/pci/controller/vmd.c:1056:
+ struct vmd_dev *vmd = pci_get_drvdata(dev);$
ERROR: code indent should use tabs where possible
#1058: FILE: drivers/pci/controller/vmd.c:1058:
+ vmd_remove_irq_domain(vmd);$
WARNING: please, no spaces at the start of a line
#1058: FILE: drivers/pci/controller/vmd.c:1058:
+ vmd_remove_irq_domain(vmd);$
No functional changes are intended.
Link: https://lore.kernel.org/linux-pci/20240901092602.17414-1-riyandhiman14@gmail.com
Signed-off-by: Riyan Dhiman <riyandhiman14@gmail.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
PARF hardware block which is a wrapper on top of DWC PCIe controller
mirrors the DBI and ATU register space. It uses PARF_SLV_ADDR_SPACE_SIZE
register to get the size of the memory block to be mirrored and uses
PARF_DBI_BASE_ADDR, PARF_ATU_BASE_ADDR registers to determine the base
address of DBI and ATU space inside the memory block that is being
mirrored.
When a memory region which is located above the SLV_ADDR_SPACE_SIZE
boundary is used for BAR region then there could be an overlap of DBI and
ATU address space that is getting mirrored and the BAR region. This
results in DBI and ATU address space contents getting updated when a PCIe
function driver tries updating the BAR/MMIO memory region. Reference
memory map of the PCIe memory region with DBI and ATU address space
overlapping BAR region is as below.
|---------------|
| |
| |
------- --------|---------------|
| | |---------------|
| | | DBI |
| | |---------------|---->DBI_BASE_ADDR
| | | |
| | | |
| PCIe | |---->2*SLV_ADDR_SPACE_SIZE
| BAR/MMIO|---------------|
| Region | ATU |
| | |---------------|---->ATU_BASE_ADDR
| | | |
PCIe | |---------------|
Memory | | DBI |
Region | |---------------|---->DBI_BASE_ADDR
| | | |
| --------| |
| | |---->SLV_ADDR_SPACE_SIZE
| |---------------|
| | ATU |
| |---------------|---->ATU_BASE_ADDR
| | |
| |---------------|
| | DBI |
| |---------------|---->DBI_BASE_ADDR
| | |
| | |
----------------|---------------|
| |
| |
| |
|---------------|
Currently memory region beyond the SLV_ADDR_SPACE_SIZE boundary is not
used for BAR region which is why the above mentioned issue is not
encountered. This issue is discovered as part of internal testing when we
tried moving the BAR region beyond the SLV_ADDR_SPACE_SIZE boundary. Hence
we are trying to fix this.
As PARF hardware block mirrors DBI and ATU register space after every
PARF_SLV_ADDR_SPACE_SIZE (default 0x1000000) boundary multiple, program
maximum possible size to this register by writing 0x80000000 to it(it
considers only powers of 2 as values) to avoid mirroring DBI and ATU to
BAR/MMIO region. Write the physical base address of DBI and ATU register
blocks to PARF_DBI_BASE_ADDR (default 0x0) and PARF_ATU_BASE_ADDR (default
0x1000) respectively to make sure DBI and ATU blocks are at expected
memory locations.
The register offsets PARF_DBI_BASE_ADDR_V2, PARF_SLV_ADDR_SPACE_SIZE_V2
and PARF_ATU_BASE_ADDR are applicable for platforms that use Qcom IP
rev 1.9.0, 2.7.0 and 2.9.0. PARF_DBI_BASE_ADDR_V2 and
PARF_SLV_ADDR_SPACE_SIZE_V2 are applicable for Qcom IP rev 2.3.3.
PARF_DBI_BASE_ADDR and PARF_SLV_ADDR_SPACE_SIZE are applicable for Qcom
IP rev 1.0.0, 2.3.2 and 2.4.0. Update init()/post_init() functions of the
respective Qcom IP versions to program applicable PARF_DBI_BASE_ADDR,
PARF_SLV_ADDR_SPACE_SIZE and PARF_ATU_BASE_ADDR register offsets. Update
the SLV_ADDR_SPACE_SZ macro to 0x80000000 to set highest bit in
PARF_SLV_ADDR_SPACE_SIZE register.
Cache DBI and iATU physical addresses in 'struct dw_pcie' so that
pcie_qcom.c driver can program these addresses in the PARF_DBI_BASE_ADDR
and PARF_ATU_BASE_ADDR registers.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/linux-pci/20240814220338.1969668-1-quic_pyarlaga@quicinc.com
Signed-off-by: Prudhvi Yarlagadda <quic_pyarlaga@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Mayank Rana <quic_mrana@quicinc.com>
Historically, Qcom PCIe RC controllers lacked standard hotplug support. So
when an endpoint is attached to the SoC, users have to rescan the bus
manually to enumerate the device. But this can be avoided by using the Link
up event exposed by the Qcom specific 'global_irq' interrupt.
Qcom PCIe RC controllers are capable of generating the 'global' SPI
interrupt to the host CPUs. The device driver can use this interrupt to
identify events such as PCIe link specific events, safety events etc...
One such event is the PCIe Link up event generated when an endpoint is
detected on the bus and the Link is 'up'. This event can be used to
enumerate the PCIe endpoint devices without user intervention.
So add support for capturing the PCIe Link up event using the 'global'
interrupt in the driver. Once the Link up event is received, the bus
underneath the host bridge is scanned to enumerate PCIe endpoint devices.
All of the Qcom SoCs have only one Root Port per controller instance. So
only a single 'Link up' event is generated for the PCIe controller.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-11-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Currently, the IRQ device name for both of these IRQs doesn't have Qcom
specific prefix and PCIe domain number. This causes 2 issues:
1. Pollutes the global IRQ namespace since 'global' is a common name.
2. When more than one EP controller instance is present in the SoC, naming
conflict will occur.
Hence, add 'qcom_pcie_ep_' prefix and PCIe domain number suffix to the IRQ
names to uniquely identify the IRQs and also to fix the above mentioned
issues.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-6-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Right now, PCI endpoint subsystem doesn't assign PCI domain number for the
PCI endpoint controllers. But this domain number could be useful to the EPC
drivers to uniquely identify each controller based on the hardware instance
when there are multiple ones present in an SoC (even multiple RC/EP).
So let's make use of the existing pci_bus_find_domain_nr() API to allocate
domain numbers based on either devicetree (linux,pci-domain) property or
dynamic domain number allocation scheme.
It should be noted that the domain number allocated by this API will be
based on both RC and EP controllers in a SoC. If the 'linux,pci-domain' DT
property is present, then the domain number represents the actual hardware
instance of the PCI endpoint controller. If not, then the domain number
will be allocated based on the PCI EP/RC controller probe order.
If the architecture doesn't support CONFIG_PCI_DOMAINS_GENERIC (rare), then
currently a warning is thrown to indicate that the architecture specific
implementation is needed.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-5-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Current error message just prints the contents of PARF_INT_ALL_STATUS
register as if like the IRQ event number. It could mislead the users.
Reword it to make it clear that the error message is actually showing the
interrupt status register to help debug spurious IRQ events.
While at it, let's also switch over to dev_WARN_ONCE() so that any IRQ
storm won't flood the kernel log buffer.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-2-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Once the events are disabled in PARF_INT_ALL_MASK register, only the
enabled events will generate global IRQ. So there is no need to do the
masking again in the IRQ handler, drop it.
If there are any spurious IRQs getting generated, they will be reported
using the existing dev_err() in the handler.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-1-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
The ACSPCIE module is capable of driving the reference clock required by
the PCIe Endpoint device. It is an alternative to on-board and external
reference clock generators. Enabling the output from the ACSPCIE module's
PAD IO Buffers requires clearing the "PAD IO disable" bits of the
ACSPCIE_PROXY_CTRL register in the CTRL_MMR register space.
Add support to enable the ACSPCIE reference clock output using the optional
device-tree property "ti,syscon-acspcie-proxy-ctrl".
Link: https://lore.kernel.org/linux-pci/20240829105316.1483684-3-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for Xilinx QDMA Soft IP core as Root Port.
The Versal Prime devices support QDMA soft IP module in programmable logic.
The integrated QDMA Soft IP block has integrated bridge function that can
act as PCIe Root Port.
Link: https://lore.kernel.org/linux-pci/20240811022345.1178203-3-thippesw@amd.com
Signed-off-by: Thippeswamy Havalige <thippesw@amd.com>
[kwilczynski: removed unused header]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-----BEGIN PGP SIGNATURE-----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=+JAO
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.11-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Add Manivannan Sadhasivam as PCI native host bridge and endpoint
driver reviewer (Manivannan Sadhasivam)
- Disable MHI RAM data parity error interrupt for qcom SA8775P SoC to
work around hardware erratum that causes a constant stream of
interrupts (Manivannan Sadhasivam)
- Don't try to fall back to qcom Operating Performance Points (OPP)
support unless the platform actually supports OPP (Manivannan
Sadhasivam)
- Add imx@lists.linux.dev mailing list to MAINTAINERS for NXP
layerscape and imx6 PCI controller drivers (Frank Li)
* tag 'pci-v6.11-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
MAINTAINERS: PCI: Add NXP PCI controller mailing list imx@lists.linux.dev
PCI: qcom: Use OPP only if the platform supports it
PCI: qcom-ep: Disable MHI RAM data parity error interrupt for SA8775P SoC
MAINTAINERS: Add Manivannan Sadhasivam as Reviewer for PCI native host bridge and endpoint drivers
PCI ATS has a global Smallest Translation Unit field that is located in
the PF but shared by all of the VFs.
The expectation is that the STU will be set to the root port's global STU
capability which is driven by the IO page table configuration of the iommu
HW. Today it becomes set when the iommu driver first enables ATS.
Thus, to enable ATS on the VF, the PF must have already had the correct
STU programmed, even if ATS is off on the PF.
Unfortunately the PF only programs the STU when the PF enables ATS. The
iommu drivers tend to leave ATS disabled when IDENTITY translation is
being used.
Thus we can get into a state where the PF is setup to use IDENTITY with
the DMA API while the VF would like to use VFIO with a PAGING domain and
have ATS turned on. This fails because the PF never loaded a PAGING domain
and so it never setup the STU, and the VF can't do it.
The simplest solution is to have the iommu driver set the ATS STU when it
probes the device. This way the ATS STU is loaded immediately at boot time
to all PFs and there is no issue when a VF comes to use it.
Add a new call pci_prepare_ats() which should be called by iommu drivers
in their probe_device() op for every PCI device if the iommu driver
supports ATS. This will setup the STU based on whatever page size
capability the iommu HW has.
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/0-v1-0fb4d2ab6770+7e706-ats_vf_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Replace the dummy implementation for PCI related functions with actual
implementation. This needs ECAM and MCFG CONFIG options to be enabled
for RISC-V.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://patch.msgid.link/20240812005929.113499-10-sunilvl@ventanamicro.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The functions defined in arm64 for ACPI support are required
for RISC-V also. To avoid duplication, move these functions
to common location.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will@kernel.org>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://patch.msgid.link/20240812005929.113499-2-sunilvl@ventanamicro.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add DMA support for audio function of Glenfly Arise chip, which uses
Requester ID of function 0.
Link: https://lore.kernel.org/r/CA2BBD087345B6D1+20240823095708.3237375-1-wangyuli@uniontech.com
Signed-off-by: SiyuLi <siyuli@glenfly.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
[bhelgaas: lower-case hex to match local code, drop unused Device IDs]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Since commit d492cc2573 ("driver core: device.h: make struct bus_type a
const *"), the driver core can properly handle constant struct bus_type,
move the pci_bus_type variable to be a constant structure as well, placing
it into read-only memory which can not be modified at runtime.
Link: https://lore.kernel.org/r/20240823074202.139265-1-kunwu.chan@linux.dev
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for ATH11K inside the WCN6855 package to the power sequencing
PCI power control driver.
Link: https://lore.kernel.org/r/20240813191201.155123-1-brgl@bgdev.pl
[Bartosz: split Konrad's bigger patch, write the commit message]
Co-developed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Konrad Dybcio <konradybcio@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Add support for enabling/disabling PCIe PHYs. We can't really do
anything about failures in the disable/remove path, so just print an
error.
Link: https://lore.kernel.org/r/20240531161337.864994-7-sean.anderson@linux.dev
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The conditions logged by the misc interrupt can occur repeatedly and
continuously. Avoid rendering the console unusable by rate-limiting
these messages.
Link: https://lore.kernel.org/r/20240531161337.864994-5-sean.anderson@linux.dev
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
MSGF_LEG_MASK is laid out with INTA in bit 0, INTB in bit 1, INTC in bit 2,
and INTD in bit 3. Hardware IRQ numbers start at 0, and we register
PCI_NUM_INTX IRQs. So to enable INTA (aka hwirq 0) we should set bit 0.
Remove the subtraction of one.
This bug would cause INTx interrupts not to be delivered, as enabling INTB
would actually enable INTA, and enabling INTA wouldn't enable anything at
all. It is likely that this got overlooked for so long since most PCIe
hardware uses MSIs. This fixes the following UBSAN error:
UBSAN: shift-out-of-bounds in ../drivers/pci/controller/pcie-xilinx-nwl.c:389:11
shift exponent 18446744073709551615 is too large for 32-bit type 'int'
CPU: 1 PID: 61 Comm: kworker/u10:1 Not tainted 6.6.20+ #268
Hardware name: xlnx,zynqmp (DT)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
dump_backtrace (arch/arm64/kernel/stacktrace.c:235)
show_stack (arch/arm64/kernel/stacktrace.c:242)
dump_stack_lvl (lib/dump_stack.c:107)
dump_stack (lib/dump_stack.c:114)
__ubsan_handle_shift_out_of_bounds (lib/ubsan.c:218 lib/ubsan.c:387)
nwl_unmask_leg_irq (drivers/pci/controller/pcie-xilinx-nwl.c:389 (discriminator 1))
irq_enable (kernel/irq/internals.h:234 kernel/irq/chip.c:170 kernel/irq/chip.c:439 kernel/irq/chip.c:432 kernel/irq/chip.c:345)
__irq_startup (kernel/irq/internals.h:239 kernel/irq/chip.c:180 kernel/irq/chip.c:250)
irq_startup (kernel/irq/chip.c:270)
__setup_irq (kernel/irq/manage.c:1800)
request_threaded_irq (kernel/irq/manage.c:2206)
pcie_pme_probe (include/linux/interrupt.h:168 drivers/pci/pcie/pme.c:348)
Fixes: 9a181e1093 ("PCI: xilinx-nwl: Modify IRQ chip for legacy interrupts")
Link: https://lore.kernel.org/r/20240531161337.864994-3-sean.anderson@linux.dev
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
With commit 5b6272e0ef ("PCI: qcom: Add OPP support to scale
performance"), OPP was used to control the interconnect and power domains
if the platform supported OPP. Also to maintain the backward compatibility
with platforms not supporting OPP but just ICC, the above mentioned commit
assumed that if ICC was not available on the platform, it would resort to
OPP.
Unfortunately, some old platforms don't support either ICC or OPP. On those
platforms, resorting to OPP in the absence of ICC throws below errors from
OPP core during suspend and resume:
qcom-pcie 1c08000.pcie: dev_pm_opp_set_opp: device opp doesn't exist
qcom-pcie 1c08000.pcie: _find_key: OPP table not found (-19)
Also, it doesn't make sense to invoke the OPP APIs when OPP is not
supported by the platform at all.
Add a "use_pm_opp" flag to identify whether OPP is supported and use it to
control invoking the OPP APIs.
Fixes: 5b6272e0ef ("PCI: qcom: Add OPP support to scale performance")
Link: https://lore.kernel.org/linux-pci/20240722131128.32470-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mayank Rana <quic_mrana@quicinc.com>
SA8775P SoC has support for the hardware parity check feature on the MHI
RAM (entity that holds MHI registers, etc.) But due to a hardware bug in
the parity check logic, the data parity error interrupt is getting
generated all the time when using MHI. So the hardware team has suggested
disabling the parity check error to work around the hardware bug.
Mask the parity error interrupt in PARF_INT_ALL_5_MASK register.
Fixes: 58d0d3e032 ("PCI: qcom-ep: Add support for SA8775P SOC")
Link: https://lore.kernel.org/linux-pci/20240808063057.7394-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This code accidentally uses && where || was intended. It potentially
results in a NULL dereference.
Thus, fix the if-statement expression to use the correct condition.
Fixes: 86f271f22b ("PCI: keystone: Add workaround for Errata #i2037 (AM65x SR 1.0)")
Link: https://lore.kernel.org/linux-pci/1b762a93-e1b2-4af3-8c04-c8843905c279@stanley.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
__pci_reset_bus() calls pci_bridge_secondary_bus_reset() to perform the
reset and also waits for the Secondary Bus to become again accessible.
__pci_reset_bus() then calls pci_bus_restore_locked() that restores the PCI
devices connected to the bus, and if necessary, recursively restores also
the subordinate buses and their devices.
The logic in pci_bus_restore_locked() does not take into account that after
restoring a device on one level, there might be another Link Downstream
that can only start to come up after restore has been performed for its
Downstream Port device. That is, the Link may require additional wait until
it becomes accessible.
Similarly, pci_slot_restore_locked() lacks wait.
Amend pci_bus_restore_locked() and pci_slot_restore_locked() to wait for
the Secondary Bus before recursively performing the restore of that bus.
Fixes: 090a3c5322 ("PCI: Add pci_reset_slot() and pci_reset_bus()")
Link: https://lore.kernel.org/r/20240808121708.2523-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pcim_iomap_regions() is a complicated function that uses a bit mask to
determine the BARs the user wishes to request and ioremap. Almost all users
only ever set a single bit in that mask, making that mechanism
questionable.
pcim_iomap_region() is now available as a more simple replacement.
Make pcim_iomap_region() a public function.
Mark pcim_iomap_regions() as deprecated.
Link: https://lore.kernel.org/r/20240807083018.8734-2-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pcim_request_region() is the managed counterpart of pci_request_region().
It is currently only used internally for PCI.
It can be useful for a number of drivers and exporting it is a step towards
deprecating more complicated functions.
Make pcim_request_region() a public function.
Link: https://lore.kernel.org/r/20240729093625.17561-4-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
