-----BEGIN PGP SIGNATURE-----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=ipv3
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Allow built-in drivers, not just modular drivers, to use async
initial probing (Lukas Wunner)
- Support Immediate Readiness even on devices with no PM Capability
(Sean Christopherson)
- Consolidate definition of PCIE_RESET_CONFIG_WAIT_MS (100ms), the
required delay between a reset and sending config requests to a
device (Niklas Cassel)
- Add pci_is_display() to check for "Display" base class and use it
in ALSA hda, vfio, vga_switcheroo, vt-d (Mario Limonciello)
- Allow 'isolated PCI functions' (multi-function devices without a
function 0) for LoongArch, similar to s390 and jailhouse (Huacai
Chen)
Power control:
- Add ability to enable optional slot clock for cases where the PCIe
host controller and the slot are supplied by different clocks
(Marek Vasut)
PCIe native device hotplug:
- Fix runtime PM ref imbalance on Hot-Plug Capable ports caused by
misinterpreting a config read failure after a device has been
removed (Lukas Wunner)
- Avoid creating a useless PCIe port service device for pciehp if the
slot is handled by the ACPI hotplug driver (Lukas Wunner)
- Ignore ACPI hotplug slots when calculating depth of pciehp hotplug
ports (Lukas Wunner)
Virtualization:
- Save VF resizable BAR state and restore it after reset (Michał
Winiarski)
- Allow IOV resources (VF BARs) to be resized (Michał Winiarski)
- Add pci_iov_vf_bar_set_size() so drivers can control VF BAR size
(Michał Winiarski)
Endpoint framework:
- Add RC-to-EP doorbell support using platform MSI controller,
including a test case (Frank Li)
- Allow BAR assignment via configfs so platforms have flexibility in
determining BAR usage (Jerome Brunet)
Native PCIe controller drivers:
- Convert amazon,al-alpine-v[23]-pcie, apm,xgene-pcie,
axis,artpec6-pcie, marvell,armada-3700-pcie, st,spear1340-pcie to
DT schema format (Rob Herring)
- Use dev_fwnode() instead of of_fwnode_handle() to remove OF
dependency in altera (fixes an unused variable), designware-host,
mediatek, mediatek-gen3, mobiveil, plda, xilinx, xilinx-dma,
xilinx-nwl (Jiri Slaby, Arnd Bergmann)
- Convert aardvark, altera, brcmstb, designware-host, iproc,
mediatek, mediatek-gen3, mobiveil, plda, rcar-host, vmd, xilinx,
xilinx-dma, xilinx-nwl from using pci_msi_create_irq_domain() to
using msi_create_parent_irq_domain() instead; this makes the
interrupt controller per-PCI device, allows dynamic allocation of
vectors after initialization, and allows support of IMS (Nam Cao)
APM X-Gene PCIe controller driver:
- Rewrite MSI handling to MSI CPU affinity, drop useless CPU hotplug
bits, use device-managed memory allocations, and clean things up
(Marc Zyngier)
- Probe xgene-msi as a standard platform driver rather than a
subsys_initcall (Marc Zyngier)
Broadcom STB PCIe controller driver:
- Add optional DT 'num-lanes' property and if present, use it to
override the Maximum Link Width advertised in Link Capabilities
(Jim Quinlan)
Cadence PCIe controller driver:
- Use PCIe Message routing types from the PCI core rather than
defining private ones (Hans Zhang)
Freescale i.MX6 PCIe controller driver:
- Add IMX8MQ_EP third 64-bit BAR in epc_features (Richard Zhu)
- Add IMX8MM_EP and IMX8MP_EP fixed 256-byte BAR 4 in epc_features
(Richard Zhu)
- Configure LUT for MSI/IOMMU in Endpoint mode so Root Complex can
trigger doorbel on Endpoint (Frank Li)
- Remove apps_reset (LTSSM_EN) from
imx_pcie_{assert,deassert}_core_reset(), which fixes a hotplug
regression on i.MX8MM (Richard Zhu)
- Delay Endpoint link start until configfs 'start' written (Richard
Zhu)
Intel VMD host bridge driver:
- Add Intel Panther Lake (PTL)-H/P/U Vendor ID (George D Sworo)
Qualcomm PCIe controller driver:
- Add DT binding and driver support for SA8255p, which supports ECAM
for Configuration Space access (Mayank Rana)
- Update DT binding and driver to describe PHYs and per-Root Port
resets in a Root Port stanza and deprecate describing them in the
host bridge; this makes it possible to support multiple Root Ports
in the future (Krishna Chaitanya Chundru)
- Add Qualcomm QCS615 to SM8150 DT binding (Ziyue Zhang)
- Add Qualcomm QCS8300 to SA8775p DT binding (Ziyue Zhang)
- Drop TBU and ref clocks from Qualcomm SM8150 and SC8180x DT
bindings (Konrad Dybcio)
- Document 'link_down' reset in Qualcomm SA8775P DT binding (Ziyue
Zhang)
- Add required PCIE_RESET_CONFIG_WAIT_MS delay after Link up IRQ
(Niklas Cassel)
Rockchip PCIe controller driver:
- Drop unused PCIe Message routing and code definitions (Hans Zhang)
- Remove several unused header includes (Hans Zhang)
- Use standard PCIe config register definitions instead of
rockchip-specific redefinitions (Geraldo Nascimento)
- Set Target Link Speed to 5.0 GT/s before retraining so we have a
chance to train at a higher speed (Geraldo Nascimento)
Rockchip DesignWare PCIe controller driver:
- Prevent race between link training and register update via DBI by
inhibiting link training after hot reset and link down (Wilfred
Mallawa)
- Add required PCIE_RESET_CONFIG_WAIT_MS delay after Link up IRQ
(Niklas Cassel)
Sophgo PCIe controller driver:
- Add DT binding and driver for Sophgo SG2044 PCIe controller driver
in Root Complex mode (Inochi Amaoto)
Synopsys DesignWare PCIe controller driver:
- Add required PCIE_RESET_CONFIG_WAIT_MS after waiting for Link up on
Ports that support > 5.0 GT/s. Slower Ports still rely on the
not-quite-correct PCIE_LINK_WAIT_SLEEP_MS 90ms default delay while
waiting for the Link (Niklas Cassel)"
* tag 'pci-v6.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (116 commits)
dt-bindings: PCI: qcom,pcie-sa8775p: Document 'link_down' reset
dt-bindings: PCI: Remove 83xx-512x-pci.txt
dt-bindings: PCI: Convert amazon,al-alpine-v[23]-pcie to DT schema
dt-bindings: PCI: Convert marvell,armada-3700-pcie to DT schema
dt-bindings: PCI: Convert apm,xgene-pcie to DT schema
dt-bindings: PCI: Convert axis,artpec6-pcie to DT schema
dt-bindings: PCI: Convert st,spear1340-pcie to DT schema
PCI: Move is_pciehp check out of pciehp_is_native()
PCI: pciehp: Use is_pciehp instead of is_hotplug_bridge
PCI/portdrv: Use is_pciehp instead of is_hotplug_bridge
PCI/ACPI: Fix runtime PM ref imbalance on Hot-Plug Capable ports
selftests: pci_endpoint: Add doorbell test case
misc: pci_endpoint_test: Add doorbell test case
PCI: endpoint: pci-epf-test: Add doorbell test support
PCI: endpoint: Add pci_epf_align_inbound_addr() helper for inbound address alignment
PCI: endpoint: pci-ep-msi: Add checks for MSI parent and mutability
PCI: endpoint: Add RC-to-EP doorbell support using platform MSI controller
PCI: dwc: Add Sophgo SG2044 PCIe controller driver in Root Complex mode
PCI: vmd: Switch to msi_create_parent_irq_domain()
PCI: vmd: Convert to lock guards
...
conversion.
-----BEGIN PGP SIGNATURE-----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=k2FW
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2025-07-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI update from Thomas Gleixner:
"A trivial cleanup in the PCI/MSI code to remove a duplicated back and
forth conversion"
* tag 'irq-msi-2025-07-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI/MSI: Remove duplicated to_pci_dev() conversion
pci_msix_write_tph_tag() takes the per device MSI descriptor mutex and then
invokes msi_domain_get_virq(), which takes the same mutex again. That
obviously results in a system hang which is exposed by a softlockup or
lockdep warning.
Move the lock guard after the invocation of msi_domain_get_virq() to fix
this.
[ tglx: Massage changelog by adding a proper explanation and removing the
not really useful stacktrace ]
Fixes: d5124a9957 ("PCI/MSI: Provide a sane mechanism for TPH")
Reported-by: Jorge Lopez <jorge.jo.lopez@oracle.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jorge Lopez <jorge.jo.lopez@oracle.com>
Link: https://lore.kernel.org/all/20250708222530.1041477-1-himanshu.madhani@oracle.com
In pci_msi_update_mask(), "lock = &to_pci_dev()" does the to_pci_dev()
lookup, and there's another one buried inside msi_desc_to_pci_dev().
Introduce a local variable to remove that duplication.
Signed-off-by: Chris Li <chrisl@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/all/20250617-pci-msi-avoid-dup-pcidev-v1-1-ed75b0419023@kernel.org
Zenghui reports that since 1396e89e09 ("genirq/msi: Move prepare() call
to per-device allocation"), his Multi-MSI capable device isn't working
anymore.
This is a consequence of 15c72f824b ("PCI/MSI: Add support for per device
MSI[X] domains"), which always creates a MSI domain of size 1, even in the
presence of Multi-MSI.
While this was somehow working until then, moving the .prepare() call ends
up sizing the ITS table with a tiny value for this device, and making the
endpoint driver unhappy.
Instead, always create the domain and call the .prepare() helper with the
maximum expected size.
Fixes: 1396e89e09 ("genirq/msi: Move prepare() call to per-device allocation")
Fixes: 15c72f824b ("PCI/MSI: Add support for per device MSI[X] domains")
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Link: https://lore.kernel.org/all/20250603141801.915305-1-maz@kernel.org
Closes: https://lore.kernel.org/r/0b1d7aec-1eac-a9cd-502a-339e216e08a1@huawei.com
- Switch the MSI decriptor locking to lock guards
- Replace a broken and naive implementation of PCI/MSI-X control word
updates in the PCI/TPH driver with a properly serialized variant in the
PCI/MSI core code.
- Remove the MSI descriptor abuse in the SCCI/UFS/QCOM driver by
replacing the direct access to the MSI descriptors with the proper API
function calls. People will never understand that APIs exist for a
reason...
- Provide core infrastructre for the upcoming PCI endpoint library
extensions. Currently limited to ARM GICv3+, but in theory extensible
to other architectures.
- Provide a MSI domain::teardown() callback, which allows drivers to undo
the effects of the prepare() callback.
- Move the MSI domain::prepare() callback invocation to domain creation
time to avoid redundant (and in case of ARM/GIC-V3-ITS confusing)
invocations on every allocation.
In combination with the new teardown callback this removes some ugly
hacks in the GIC-V3-ITS driver, which pretended to work around the
short comings of the core code so far. With this update the code is
correct by design and implementation.
- Make the irqchip MSI library globally available, provide a MSI parent
domain creation helper and convert a bunch of (PCI/)MSI drivers over to
the modern MSI parent mechanism. This is the first step to get rid of
at least one incarnation of the three PCI/MSI management schemes.
- The usual small cleanups and improvements
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAmgzgFsTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoR0KD/402K12tlI/D70H2aTG25dbTx+dkVk+
pKpJz0985uUlLJiPCR54dZL0ofcfRU+CdjEIf1I+6TPshtg6IWLJCfqu7OWVPYzz
2lJDO0yeUGwJqc0CIa1vttvJWvcUcxfWBX/ZSkOIM5avaXqSwRwsFNfd7TQ+T+eG
79VS1yyW197mUva53ekSF2voa8EEPWfEslAjoX1dRg5d4viAxaLtKm/KpBqo1oPh
Eb+E67xEWiIonvWNdr1AOisxnbi19PyDo1xnftgBToaeXXYBodNrNIAfAkx40YUZ
IZQLHvhZ91x15hXYIS4Cz1RXqPECbu/tHxs4AFUgGvqdgJUF89wzI3C21ymrKA6E
tDlWfpIcuE3vV/bsqj1gHGL5G5m1tyBRgIdIAOOmMoTHvwp5rrQtuZzpuqzGmEzj
iVIHnn5m08kRpOZQc7+PlxQMh3eunEyj9WWG49EJgoAnJPb5lou4shTwBUheHcKm
NXxKsfo4x5C+WehGTxv80UlnMcK3Yh/TuWf2OPR6QuT2iHP2VL5jyHjIs0ICn0cp
1tvSJtdc1rgvk/4Vn4lu5eyVaTx5ZAH8ZXNQfwwBTWTp3ZyAW+7GkaCq3LPaNJoZ
4LWpgZ5gs6wT+1XNT3boKdns81VolmeTI8P1ciQKpUtaTt6Cy9P/i2az/J+BCS4U
Fn5Qqk08PHGrUQ==
=OBMj
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2025-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI updates from Thomas Gleixner:
"Updates for the MSI subsystem (core code and PCI):
- Switch the MSI descriptor locking to lock guards
- Replace a broken and naive implementation of PCI/MSI-X control word
updates in the PCI/TPH driver with a properly serialized variant in
the PCI/MSI core code.
- Remove the MSI descriptor abuse in the SCCI/UFS/QCOM driver by
replacing the direct access to the MSI descriptors with the proper
API function calls. People will never understand that APIs exist
for a reason...
- Provide core infrastructre for the upcoming PCI endpoint library
extensions. Currently limited to ARM GICv3+, but in theory
extensible to other architectures.
- Provide a MSI domain::teardown() callback, which allows drivers to
undo the effects of the prepare() callback.
- Move the MSI domain::prepare() callback invocation to domain
creation time to avoid redundant (and in case of ARM/GIC-V3-ITS
confusing) invocations on every allocation.
In combination with the new teardown callback this removes some
ugly hacks in the GIC-V3-ITS driver, which pretended to work around
the short comings of the core code so far. With this update the
code is correct by design and implementation.
- Make the irqchip MSI library globally available, provide a MSI
parent domain creation helper and convert a bunch of (PCI/)MSI
drivers over to the modern MSI parent mechanism. This is the first
step to get rid of at least one incarnation of the three PCI/MSI
management schemes.
- The usual small cleanups and improvements"
* tag 'irq-msi-2025-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
PCI/MSI: Use bool for MSI enable state tracking
PCI: tegra: Convert to MSI parent infrastructure
PCI: xgene: Convert to MSI parent infrastructure
PCI: apple: Convert to MSI parent infrastructure
irqchip/msi-lib: Honour the MSI_FLAG_NO_AFFINITY flag
irqchip/mvebu: Convert to msi_create_parent_irq_domain() helper
irqchip/gic: Convert to msi_create_parent_irq_domain() helper
genirq/msi: Add helper for creating MSI-parent irq domains
irqchip: Make irq-msi-lib.h globally available
irqchip/gic-v3-its: Use allocation size from the prepare call
genirq/msi: Engage the .msi_teardown() callback on domain removal
genirq/msi: Move prepare() call to per-device allocation
irqchip/gic-v3-its: Implement .msi_teardown() callback
genirq/msi: Add .msi_teardown() callback as the reverse of .msi_prepare()
irqchip/gic-v3-its: Add support for device tree msi-map and msi-mask
dt-bindings: PCI: pci-ep: Add support for iommu-map and msi-map
irqchip/gic-v3-its: Set IRQ_DOMAIN_FLAG_MSI_IMMUTABLE for ITS
irqdomain: Add IRQ_DOMAIN_FLAG_MSI_IMMUTABLE and irq_domain_is_msi_immutable()
platform-msi: Add msi_remove_device_irq_domain() in platform_device_msi_free_irqs_all()
genirq/msi: Rename msi_[un]lock_descs()
...
Convert pci_msi_enable and pci_msi_enabled() to use bool type for clarity.
No functional changes, only code cleanup.
Signed-off-by: Hans Zhang <hans.zhang@cixtech.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250516165223.125083-2-18255117159@163.com
Commit 7d5ec3d361 ("PCI/MSI: Mask all unused MSI-X entries") introduced a
readl() from ENTRY_VECTOR_CTRL before the writel() to ENTRY_DATA.
This is correct, however some hardware, like the Sun Neptune chips, the NIU
module, will cause an error and/or fatal trap if any MSIX table entry is
read before the corresponding ENTRY_DATA field is written to.
Add an optional early writel() in msix_prepare_msi_desc().
Fixes: 7d5ec3d361 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Jonathan Currier <dullfire@yahoo.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20241117234843.19236-2-dullfire@yahoo.com
The PCI/TPH driver fiddles with the MSI-X control word of an active
interrupt completely unserialized against concurrent operations issued
from the interrupt core. It also brings the PCI/MSI-X internal cached
control word out of sync.
Provide a function, which has the required serialization and keeps the
control word cache in sync.
Unfortunately this requires to look up and lock the interrupt descriptor,
which should be only done in the interrupt core code. But confining this
particular oddity in the PCI/MSI core is the lesser of all evil. A
interrupt core implementation would require a larger pile of infrastructure
and indirections for dubious value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/all/20250319105506.683663807@linutronix.de
Split the lock protected functionality of msix_capability_init() out into a
helper function and use guard(msi_desc_lock) to replace the lock/unlock
pair.
Simplify the error path in the helper function by utilizing a custom
cleanup to get rid of the remaining gotos.
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/all/20250319105506.564105011@linutronix.de
Split the lock protected functionality of msi_capability_init() out into a
helper function and use guard(msi_desc_lock) to replace the lock/unlock
pair.
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/all/20250319105506.504992208@linutronix.de
Let cleanup handle the freeing of the affinity mask. That prepares for
switching the MSI descriptor locking to a guard().
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/all/20250319105506.444764312@linutronix.de
The comment claiming that pci_dev::msi_enabled has to be set across setup
is a leftover from ancient code versions. Nothing in the setup code
requires the flag to be set anymore.
Set it in the success path and remove the extra goto label.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/all/20250319105506.383222333@linutronix.de
This reverts commit 36f5f026df, reversing
changes made to 43a7eec035.
Thomas says:
"I just noticed that for some incomprehensible reason, probably sheer
incompetemce when trying to utilize b4, I managed to merge an outdated
_and_ buggy version of that series.
Can you please revert that merge completely?"
Done.
Requested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The conversion of the XEN specific global variable pci_msi_ignore_mask to a
MSI domain flag, missed the facts that:
1) Legacy architectures do not provide a interrupt domain
2) Parent MSI domains do not necessarily have a domain info attached
Both cases result in an unconditional NULL pointer dereference. This was
unfortunatly missed in review and testing revealed it late.
Cure this by using the existing pci_msi_domain_supports() helper, which
handles all possible cases correctly.
Fixes: c3164d2e0d ("PCI/MSI: Convert pci_msi_ignore_mask to per MSI domain flag")
Reported-by: Daniel Gomez <da.gomez@kernel.org>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Borislav Petkov <bp@alien8.de>
Tested-by: Daniel Gomez <da.gomez@kernel.org>
Link: https://lore.kernel.org/all/87iknwyp2o.ffs@tglx
Closes: https://lore.kernel.org/all/qn7fzggcj6qe6r6gdbwcz23pzdz2jx64aldccmsuheabhmjgrt@tawf5nfwuvw7
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCZ9/gEwAKCRCAXGG7T9hj
vlxhAQCRzSCNI8wwvENnuc2OnRyWKy8gq7C5WAOIOJdJ3U+scQEAwKGhPJLwE4IS
/JDh5PRJgZ4rdMYatuDfldEcSAfRRgw=
=dF6Z
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- cleanup: remove an used function
- add support for a XenServer specific virtual PCI device
- fix the handling of a sparse Xen hypervisor symbol table
- avoid warnings when building the kernel with gcc 15
- fix use of devices behind a VMD bridge when running as a Xen PV dom0
* tag 'for-linus-6.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
PCI/MSI: Convert pci_msi_ignore_mask to per MSI domain flag
PCI: vmd: Disable MSI remapping bypass under Xen
xen/pci: Do not register devices with segments >= 0x10000
xen/pciback: Remove unused pcistub_get_pci_dev
xenfs/xensyms: respect hypervisor's "next" indication
xen/mcelog: Add __nonstring annotations for unterminated strings
xen: Add support for XenServer 6.1 platform device
Setting pci_msi_ignore_mask inhibits the toggling of the mask bit for both
MSI and MSI-X entries globally, regardless of the IRQ chip they are using.
Only Xen sets the pci_msi_ignore_mask when routing physical interrupts over
event channels, to prevent PCI code from attempting to toggle the maskbit,
as it's Xen that controls the bit.
However, the pci_msi_ignore_mask being global will affect devices that use
MSI interrupts but are not routing those interrupts over event channels
(not using the Xen pIRQ chip). One example is devices behind a VMD PCI
bridge. In that scenario the VMD bridge configures MSI(-X) using the
normal IRQ chip (the pIRQ one in the Xen case), and devices behind the
bridge configure the MSI entries using indexes into the VMD bridge MSI
table. The VMD bridge then demultiplexes such interrupts and delivers to
the destination device(s). Having pci_msi_ignore_mask set in that scenario
prevents (un)masking of MSI entries for devices behind the VMD bridge.
Move the signaling of no entry masking into the MSI domain flags, as that
allows setting it on a per-domain basis. Set it for the Xen MSI domain
that uses the pIRQ chip, while leaving it unset for the rest of the
cases.
Remove pci_msi_ignore_mask at once, since it was only used by Xen code, and
with Xen dropping usage the variable is unneeded.
This fixes using devices behind a VMD bridge on Xen PV hardware domains.
Albeit Devices behind a VMD bridge are not known to Xen, that doesn't mean
Linux cannot use them. By inhibiting the usage of
VMD_FEAT_CAN_BYPASS_MSI_REMAP and the removal of the pci_msi_ignore_mask
bodge devices behind a VMD bridge do work fine when use from a Linux Xen
hardware domain. That's the whole point of the series.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Message-ID: <20250219092059.90850-4-roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
The PCI/TPH driver fiddles with the MSI-X control word of an active
interrupt completely unserialized against concurrent operations issued
from the interrupt core. It also brings the PCI/MSI-X internal cached
control word out of sync.
Provide a function, which has the required serialization and keeps the
control word cache in sync.
Unfortunately this requires to look up and lock the interrupt descriptor,
which should be only done in the interrupt core code. But confining this
particular oddity in the PCI/MSI core is the lesser of all evil. A
interrupt core implementation would require a larger pile of infrastructure
and indirections for dubious value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/all/20250313130321.822790423@linutronix.de
Convert the code to use the new guard(msi_descs_lock).
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/all/20250313130321.695027112@linutronix.de
Alexandre observed a warning emitted from pci_msi_setup_msi_irqs() on a
RISCV platform which does not provide PCI/MSI support:
WARNING: CPU: 1 PID: 1 at drivers/pci/msi/msi.h:121 pci_msi_setup_msi_irqs+0x2c/0x32
__pci_enable_msix_range+0x30c/0x596
pci_msi_setup_msi_irqs+0x2c/0x32
pci_alloc_irq_vectors_affinity+0xb8/0xe2
RISCV uses hierarchical interrupt domains and correctly does not implement
the legacy fallback. The warning triggers from the legacy fallback stub.
That warning is bogus as the PCI/MSI layer knows whether a PCI/MSI parent
domain is associated with the device or not. There is a check for MSI-X,
which has a legacy assumption. But that legacy fallback assumption is only
valid when legacy support is enabled, but otherwise the check should simply
return -ENOTSUPP.
Loongarch tripped over the same problem and blindly enabled legacy support
without implementing the legacy fallbacks. There are weak implementations
which return an error, so the problem was papered over.
Correct pci_msi_domain_supports() to evaluate the legacy mode and add
the missing supported check into the MSI enable path to complete it.
Fixes: d2a463b297 ("PCI/MSI: Reject multi-MSI early")
Reported-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/87ed2a8ow5.ffs@tglx
KFENCE reports the following UAF:
BUG: KFENCE: use-after-free read in __pci_enable_msi_range+0x2c0/0x488
Use-after-free read at 0x0000000024629571 (in kfence-#12):
__pci_enable_msi_range+0x2c0/0x488
pci_alloc_irq_vectors_affinity+0xec/0x14c
pci_alloc_irq_vectors+0x18/0x28
kfence-#12: 0x0000000008614900-0x00000000e06c228d, size=104, cache=kmalloc-128
allocated by task 81 on cpu 7 at 10.808142s:
__kmem_cache_alloc_node+0x1f0/0x2bc
kmalloc_trace+0x44/0x138
msi_alloc_desc+0x3c/0x9c
msi_domain_insert_msi_desc+0x30/0x78
msi_setup_msi_desc+0x13c/0x184
__pci_enable_msi_range+0x258/0x488
pci_alloc_irq_vectors_affinity+0xec/0x14c
pci_alloc_irq_vectors+0x18/0x28
freed by task 81 on cpu 7 at 10.811436s:
msi_domain_free_descs+0xd4/0x10c
msi_domain_free_locked.part.0+0xc0/0x1d8
msi_domain_alloc_irqs_all_locked+0xb4/0xbc
pci_msi_setup_msi_irqs+0x30/0x4c
__pci_enable_msi_range+0x2a8/0x488
pci_alloc_irq_vectors_affinity+0xec/0x14c
pci_alloc_irq_vectors+0x18/0x28
Descriptor allocation done in:
__pci_enable_msi_range
msi_capability_init
msi_setup_msi_desc
msi_insert_msi_desc
msi_domain_insert_msi_desc
msi_alloc_desc
...
Freed in case of failure in __msi_domain_alloc_locked()
__pci_enable_msi_range
msi_capability_init
pci_msi_setup_msi_irqs
msi_domain_alloc_irqs_all_locked
msi_domain_alloc_locked
__msi_domain_alloc_locked => fails
msi_domain_free_locked
...
That failure propagates back to pci_msi_setup_msi_irqs() in
msi_capability_init() which accesses the descriptor for unmasking in the
error exit path.
Cure it by copying the descriptor and using the copy for the error exit path
unmask operation.
[ tglx: Massaged change log ]
Fixes: bf6e054e0e ("genirq/msi: Provide msi_device_populate/destroy_sysfs()")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Heelgas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240624203729.1094506-1-smostafa@google.com
Make error path handling follow the standard pattern, i.e. checking for
errors first. This makes code much easier to read and understand despite
being a bit longer.
Link: https://lore.kernel.org/r/20240426144039.557907-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_msix_validate_entries() validates the entries array which is handed in
by the caller for a MSI-X interrupt allocation. Aside of consistency
failures it also detects a failure when the size of the MSI-X hardware table
in the device is smaller than the size of the entries array.
That's wrong for the case of range allocations where the caller provides
the minimum and the maximum number of vectors to allocate, when the
hardware size is greater or equal than the mininum, but smaller than the
maximum.
Remove the hardware size check completely from that function and just
ensure that the entires array up to the maximum size is consistent.
The limitation and range checking versus the hardware size happens
independently of that afterwards anyway because the entries array is
optional.
Fixes: 4644d22eb6 ("PCI/MSI: Validate MSI-X contiguous restriction early")
Reported-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87v8i3sg62.ffs@tglx
The upcoming mechanism to allocate MSI-X vectors after enabling MSI-X needs
to share some of the MSI-X descriptor setup.
The regular descriptor setup on enable has the following code flow:
1) Allocate descriptor
2) Setup descriptor with PCI specific data
3) Insert descriptor
4) Allocate interrupts which in turn scans the inserted
descriptors
This cannot be easily changed because the PCI/MSI code needs to handle the
legacy architecture specific allocation model and the irq domain model
where quite some domains have the assumption that the above flow is how it
works.
Ideally the code flow should look like this:
1) Invoke allocation at the MSI core
2) MSI core allocates descriptor
3) MSI core calls back into the irq domain which fills in
the domain specific parts
This could be done for underlying parent MSI domains which support
post-enable allocation/free but that would create significantly different
code pathes for MSI/MSI-X enable.
Though for dynamic allocation which wants to share the allocation code with
the upcoming PCI/IMS support it's the right thing to do.
Split the MSI-X descriptor setup into the preallocation part which just sets
the index and fills in the horrible hack of virtual IRQs and the real PCI
specific MSI-X setup part which solely depends on the index in the
descriptor. This allows to provide a common dynamic allocation interface at
the MSI core level for both PCI/MSI-X and PCI/IMS.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221124232326.616292598@linutronix.de
Provide a template and the necessary callbacks to create PCI/MSI and
PCI/MSI-X domains.
The domains are created when MSI or MSI-X is enabled. The domain's lifetime
is either the device lifetime or in case that e.g. MSI-X was tried first
and failed, then the MSI-X domain is removed and a MSI domain is created as
both are mutually exclusive and reside in the default domain ID slot of the
per device domain pointer array.
Also expand pci_msi_domain_supports() to handle feature checks correctly
even in the case that the per device domain was not yet created by checking
the features supported by the MSI parent.
Add the necessary setup calls into the MSI and MSI-X enable code path.
These setup calls are backwards compatible. They return success when there
is no parent domain found, which means the existing global domains or the
legacy allocation path keep just working.
Co-developed-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221124232325.975388241@linutronix.de
The upcoming per device MSI domains will create different domains for MSI
and MSI-X. Split the write message function into MSI and MSI-X helpers so
they can be used by those new domain functions seperately.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221124232325.857982142@linutronix.de
This reflects the functionality better. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221124230314.103554618@linutronix.de
With interrupt domains the sanity check for MSI-X vector validation can be
done _before_ any allocation happens. The sanity check only applies to the
allocation functions which have an 'entries' array argument. The entries
array is filled by the caller with the requested MSI-X indices. Some drivers
have gaps in the index space which is not supported on all architectures.
The PCI/MSI irq domain has a 'feature' bit to enforce this validation late
during the allocation phase.
Just do it right away before doing any other work along with the other
sanity checks on that array.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122015.691357406@linutronix.de
Similar to PCI multi-MSI reject MSI-X enablement when a irq domain is
attached to the device which does not support MSI-X.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122015.631728309@linutronix.de
When hierarchical MSI interrupt domains are enabled then there is no point
to do tons of work and detect the missing support for multi-MSI late in the
allocation path.
Just query the domain feature flags right away. The query function is going
to be used for other purposes later and has a mode argument which influences
the result:
ALLOW_LEGACY returns true when:
- there is no irq domain attached (legacy support)
- there is a irq domain attached which has the feature flag set
DENY_LEGACY returns only true when:
- there is a irq domain attached which has the feature flag set
This allows to use the function universally without ifdeffery in the
calling code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122015.574339988@linutronix.de
There is no point in doing the same sanity checks over and over in a loop
during MSI-X enablement. Put them in front of the loop and return early
when they fail.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122015.516946468@linutronix.de
There is no way to navigate msi.c without banging the head against the wall
every now and then because MSI and MSI-X specific functions are
intermingled and the code flow is completely non-obvious.
Reorder everthing so common helpers, MSI and MSI-X specific functions are
grouped together.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122015.459089736@linutronix.de
To disentangle the maze in msi.c, all exported device-driver MSI APIs are
now to be grouped in one file, api.c.
Move pci_msi_enabled() and add kernel-doc for the function.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122015.331584998@linutronix.de
To disentangle the maze in msi.c, all exported device-driver MSI APIs are
now to be grouped in one file, api.c.
Move pci_msi_enabled() and make its kernel-doc comprehensive.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122015.271447896@linutronix.de
To disentangle the maze in msi.c, all exported device-driver MSI APIs are
now to be grouped in one file, api.c.
Move pci_irq_get_affinity() and let its kernel-doc match rest of the
file.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122015.214792769@linutronix.de
To disentangle the maze in msi.c, all exported device-driver MSI APIs are
now to be grouped in one file, api.c.
Move pci_disable_msix() and make its kernel-doc comprehensive.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122015.156785224@linutronix.de
To disentangle the maze in msi.c, all exported device-driver MSI APIs are
now to be grouped in one file, api.c.
Move pci_msix_vec_count() and make its kernel-doc comprehensive.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122015.099461602@linutronix.de
To disentangle the maze in msi.c, all exported device-driver MSI APIs are
now to be grouped in one file, api.c.
Move pci_free_irq_vectors() and make its kernel-doc comprehensive.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122015.042870570@linutronix.de
To disentangle the maze in msi.c, all exported device-driver MSI APIs are
now to be grouped in one file, api.c.
Move pci_irq_vector() and let its kernel-doc match the rest of the file.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122014.984490384@linutronix.de
To disentangle the maze in msi.c, all exported device-driver MSI APIs are
now to be grouped in one file, api.c.
Move pci_alloc_irq_vectors_affinity() and let its kernel-doc reference
pci_alloc_irq_vectors() documentation added in parent commit.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122014.927531290@linutronix.de
To disentangle the maze in msi.c, all exported device-driver MSI APIs are
now to be grouped in one file, api.c.
Move pci_enable_msix_range() and make its kernel-doc comprehensive.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122014.813792885@linutronix.de
To disentangle the maze in msi.c all exported device-driver MSI APIs are
now to be grouped in one file, api.c.
Move pci_enable_msi() and make its kernel-doc comprehensive.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122014.755178149@linutronix.de
msi.c is a maze of randomly sorted functions which makes the code
unreadable. As a first step split the driver visible API and the internal
implementation which also allows proper API documentation via one file.
Create drivers/pci/msi/api.c to group all exported device-driver PCI/MSI
APIs in one C file.
Begin by moving pci_disable_msi() there and add kernel-doc for the function
as appropriate.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122014.696798036@linutronix.de
The upcoming support for per device MSI interrupt domains needs to share
some of the inline helpers with the MSI implementation.
Move them to the header file.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122014.640052354@linutronix.de
PCI/MSI and PCI/MSI-X are mutually exclusive, but the MSI-X enable code
lacks a check for already enabled MSI.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122013.653556720@linutronix.de
71020a3c0d ("PCI/MSI: Use msi_add_msi_desc()") inadvertently reversed
the sense of "msi_attrib.can_mask" in one use:
- if (entry->pci.msi_attrib.can_mask) {
- addr = pci_msix_desc_addr(entry);
- entry->pci.msix_ctrl = readl(addr + PCI_MSIX_ENTRY_VECTOR_CTRL);
+ if (!desc.pci.msi_attrib.can_mask) {
+ addr = pci_msix_desc_addr(&desc);
+ desc.pci.msix_ctrl = readl(addr + PCI_MSIX_ENTRY_VECTOR_CTRL);
Restore the original test.
[bhelgaas: commit log]
Fixes: 71020a3c0d ("PCI/MSI: Use msi_add_msi_desc()")
Link: https://lore.kernel.org/r/d818f9c9-a432-213e-4152-eaff3b7da52e@oderland.se
Signed-off-by: Josef Johansson <josef@oderland.se>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
The recent overhaul of pci_irq_get_affinity() introduced a regression when
pci_irq_get_affinity() is called for an MSI-X interrupt which was not
allocated with affinity descriptor information.
The original code just returned a NULL pointer in that case, but the rework
added a WARN_ON() under the assumption that the corresponding WARN_ON() in
the MSI case can be applied to MSI-X as well.
In fact the MSI warning in the original code does not make sense either
because it's legitimate to invoke pci_irq_get_affinity() for a MSI
interrupt which was not allocated with affinity descriptor information.
Remove it and just return NULL as the original code did.
Fixes: f482359001 ("PCI/MSI: Simplify pci_irq_get_affinity()")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/87ee4n38sm.ffs@tglx
