It is reported that on some systems pciehp binds to an Upstream Port and
attempts to operate it which causes devices below the Port to disappear
from the bus.
This happens because acpiphp sets dev->is_hotplug_bridge for that Port
(after receiving a Device Check notification on it from the platform
firmware via ACPI) during the enumeration of PCI devices.
get_port_device_capability() sees that dev->is_hotplug_bridge is set and
adds PCIE_PORT_SERVICE_HP to Port services, which allows pciehp to bind to
the Port in question.
Even though this particular problem can be addressed by making the
portdrv_core checks more robust, it also causes power management to work
differently on the affected systems which generally is not desirable (PCIe
Ports with dev->is_hotplug_bridge set have to pass additional tests to be
allowed to go into the D3hot/cold power states which affects runtime PM of
devices below these Ports).
For this reason, amend check_hotplug_bridge() with a PCIe type check to
prevent it from setting dev->is_hotplug_bridge for Upstream Ports.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2262230.ElGaqSPkdT@kreacher
Reported-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
-----BEGIN PGP SIGNATURE-----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=5Q9H
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Move the VGA arbiter from drivers/gpu to drivers/pci because it's
PCI-specific, not GPU-specific (Bjorn Helgaas)
- Select the default VGA device consistently whether it's enumerated
before or after VGA arbiter init, which fixes arches that enumerate
PCI devices late (Huacai Chen)
Resource management:
- Support BAR sizes up to 8TB (Dongdong Liu)
PCIe native device hotplug:
- Fix "Command Completed" tracking to avoid spurious timouts when
powering off empty slots (Liguang Zhang)
- Quirk Qualcomm devices that don't implement Command Completed
correctly, again to avoid spurious timeouts (Manivannan Sadhasivam)
Peer-to-peer DMA:
- Add Intel 3rd Gen Intel Xeon Scalable Processors to whitelist
(Michael J. Ruhl)
APM X-Gene PCIe controller driver:
- Revert generic DT parsing changes that broke some machines in the
field (Marc Zyngier)
Freescale i.MX6 PCIe controller driver:
- Allow controller probe to succeed even when no devices currently
present to allow hot-add later (Fabio Estevam)
- Enable power management on i.MX6QP (Richard Zhu)
- Assert CLKREQ# on i.MX8MM so enumeration doesn't hang when no
device is connected (Richard Zhu)
Marvell Aardvark PCIe controller driver:
- Fix MSI and MSI-X support (Marek Behún, Pali Rohár)
- Add support for ERR and PME interrupts (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Add DT binding and support for "num-lanes" (Pali Rohár)
- Add support for INTx interrupts (Pali Rohár)
Microsoft Hyper-V host bridge driver:
- Avoid unnecessary hypercalls when unmasking IRQs on ARM64 (Boqun
Feng)
Qualcomm PCIe controller driver:
- Add SM8450 DT binding and driver support (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Help the controller get to the L1 state since the hardware can't do
it on its own (Marek Vasut)
- Return PCI_ERROR_RESPONSE (~0) for reads that fail on PCIe (Marek
Vasut)
SiFive FU740 PCIe controller driver:
- Drop redundant '-gpios' from DT GPIO lookup (Ben Dooks)
- Force 2.5GT/s for initial device probe (Ben Dooks)
Socionext UniPhier Pro5 controller driver:
- Add NX1 DT binding and driver support (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Restore MSI configuration so MSI works after resume (Jisheng
Zhang)"
* tag 'pci-v5.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (94 commits)
x86/PCI: Add #includes to asm/pci_x86.h
PCI: ibmphp: Remove unused assignments
PCI: cpqphp: Remove unused assignments
PCI: fu740: Remove unused assignments
PCI: kirin: Remove unused assignments
PCI: Remove unused assignments
PCI: Declare pci_filp_private only when HAVE_PCI_MMAP
PCI: Avoid broken MSI on SB600 USB devices
PCI: fu740: Force 2.5GT/s for initial device probe
PCI: xgene: Revert "PCI: xgene: Fix IB window setup"
PCI: xgene: Revert "PCI: xgene: Use inbound resources for setup"
PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present
PCI: imx6: Invoke the PHY exit function after PHY power off
PCI: rcar: Use PCI_SET_ERROR_RESPONSE after read which triggered an exception
PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()
PCI: dwc: Restore MSI Receiver mask during resume
PCI: fu740: Drop redundant '-gpios' from DT GPIO lookup
PCI/VGA: Replace full MIT license text with SPDX identifier
PCI/VGA: Use unsigned format string to print lock counts
PCI/VGA: Log bridge control messages when adding devices
...
- Clear pciehp cmd_busy bit when command completes in polling mode to avoid
spurious timeouts (Liguang Zhang)
- Add quirk to work around Qualcomm hardware defect in Command Completed
signaling (Manivannan Sadhasivam)
* pci/hotplug:
PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
PCI: pciehp: Clear cmd_busy bit in polling mode
- Add and use #defines for normal and subtractive PCI bridges (Pali Rohár)
- Set all 24 bits of PCI class code for iproc (Pali Rohár)
* pci/bridge-class-codes:
PCI: iproc: Set all 24 bits of PCI class code
PCI: Add defines for normal and subtractive PCI bridges
Remove variables and assignments that are never used.
Found by Krzysztof using cppcheck, e.g.:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/hotplug/ibmphp_res.c:1958 Variable 'bus_sec' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove variables and assignments that are never used.
Found by Krzysztof using cppcheck, e.g.:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/hotplug/cpqphp_core.c:1257 Variable 'rc' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-5-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add these PCI class codes to pci_ids.h:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
Use these defines in all kernel code for describing PCI class codes for
normal and subtractive PCI bridges.
[bhelgaas: similar change in pci-mvebu.c]
Link: https://lore.kernel.org/r/20220214114109.26809-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Qualcomm PCI bridge device (Device ID 0x0110) found in chipsets such as
SM8450 does not set the Command Completed bit unless writes to the Slot
Command register change "Control" bits.
This results in timeouts like below:
pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
Add the device to the Command Completed quirk to mark commands "completed"
immediately unless they change the "Control" bits.
Link: https://lore.kernel.org/r/20220210145003.135907-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replace acpi_bus_get_device() that is going to be dropped with
acpi_fetch_acpi_dev().
No intentional functional impact.
Link: https://lore.kernel.org/r/11930209.O9o76ZdvQC@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Writes to a Downstream Port's Slot Control register are PCIe hotplug
"commands." If the Port supports Command Completed events, software must
wait for a command to complete before writing to Slot Control again.
pcie_do_write_cmd() sets ctrl->cmd_busy when it writes to Slot Control. If
software notification is enabled, i.e., PCI_EXP_SLTCTL_HPIE and
PCI_EXP_SLTCTL_CCIE are set, ctrl->cmd_busy is cleared by pciehp_isr().
But when software notification is disabled, as it is when pcie_init()
powers off an empty slot, pcie_wait_cmd() uses pcie_poll_cmd() to poll for
command completion, and it neglects to clear ctrl->cmd_busy, which leads to
spurious timeouts:
pcieport 0000:00:03.0: pciehp: Timeout on hotplug command 0x01c0 (issued 2264 msec ago)
pcieport 0000:00:03.0: pciehp: Timeout on hotplug command 0x05c0 (issued 2288 msec ago)
Clear ctrl->cmd_busy in pcie_poll_cmd() when it detects a Command Completed
event (PCI_EXP_SLTSTA_CC).
[bhelgaas: commit log]
Fixes: a5dd4b4b05 ("PCI: pciehp: Wait for hotplug command completion where necessary")
Link: https://lore.kernel.org/r/20211111054258.7309-1-zhangliguang@linux.alibaba.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215143
Link: https://lore.kernel.org/r/20211126173309.GA12255@wunner.de
Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.19+
- Add PCI_ERROR_RESPONSE and related definitions for signaling and checking
for transaction errors on PCI (Naveen Naidu)
- Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers, instead
of in host controller drivers, when transactions fail on PCI (Naveen
Naidu)
- Use PCI_POSSIBLE_ERROR() to check for possible failure of config reads
(Naveen Naidu)
* pci/errors:
PCI: xgene: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: hv: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: keystone: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: cpqphp: Use PCI_POSSIBLE_ERROR() to check config reads
PCI/PME: Use PCI_POSSIBLE_ERROR() to check config reads
PCI/DPC: Use PCI_POSSIBLE_ERROR() to check config reads
PCI: pciehp: Use PCI_POSSIBLE_ERROR() to check config reads
PCI: vmd: Use PCI_POSSIBLE_ERROR() to check config reads
PCI/ERR: Use PCI_POSSIBLE_ERROR() to check config reads
PCI: rockchip-host: Drop error data fabrication when config read fails
PCI: rcar-host: Drop error data fabrication when config read fails
PCI: altera: Drop error data fabrication when config read fails
PCI: mvebu: Drop error data fabrication when config read fails
PCI: aardvark: Drop error data fabrication when config read fails
PCI: kirin: Drop error data fabrication when config read fails
PCI: histb: Drop error data fabrication when config read fails
PCI: exynos: Drop error data fabrication when config read fails
PCI: mediatek: Drop error data fabrication when config read fails
PCI: iproc: Drop error data fabrication when config read fails
PCI: thunder: Drop error data fabrication when config read fails
PCI: Drop error data fabrication when config read fails
PCI: Use PCI_SET_ERROR_RESPONSE() for disconnected devices
PCI: Set error response data when config read fails
PCI: Add PCI_ERROR_RESPONSE and related definitions
Use down_read_nested() and down_write_nested() when taking the
ctrl->reset_lock rw-sem, passing the number of PCIe hotplug controllers in
the path to the PCI root bus as lock subclass parameter.
This fixes the following false-positive lockdep report when unplugging a
Lenovo X1C8 from a Lenovo 2nd gen TB3 dock:
pcieport 0000:06:01.0: pciehp: Slot(1): Link Down
pcieport 0000:06:01.0: pciehp: Slot(1): Card not present
============================================
WARNING: possible recursive locking detected
5.16.0-rc2+ #621 Not tainted
--------------------------------------------
irq/124-pciehp/86 is trying to acquire lock:
ffff8e5ac4299ef8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_check_presence+0x23/0x80
but task is already holding lock:
ffff8e5ac4298af8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_ist+0xf3/0x180
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&ctrl->reset_lock);
lock(&ctrl->reset_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by irq/124-pciehp/86:
#0: ffff8e5ac4298af8 (&ctrl->reset_lock){.+.+}-{3:3}, at: pciehp_ist+0xf3/0x180
#1: ffffffffa3b024e8 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pciehp_unconfigure_device+0x31/0x110
#2: ffff8e5ac1ee2248 (&dev->mutex){....}-{3:3}, at: device_release_driver+0x1c/0x40
stack backtrace:
CPU: 4 PID: 86 Comm: irq/124-pciehp Not tainted 5.16.0-rc2+ #621
Hardware name: LENOVO 20U90SIT19/20U90SIT19, BIOS N2WET30W (1.20 ) 08/26/2021
Call Trace:
<TASK>
dump_stack_lvl+0x59/0x73
__lock_acquire.cold+0xc5/0x2c6
lock_acquire+0xb5/0x2b0
down_read+0x3e/0x50
pciehp_check_presence+0x23/0x80
pciehp_runtime_resume+0x5c/0xa0
device_for_each_child+0x45/0x70
pcie_port_device_runtime_resume+0x20/0x30
pci_pm_runtime_resume+0xa7/0xc0
__rpm_callback+0x41/0x110
rpm_callback+0x59/0x70
rpm_resume+0x512/0x7b0
__pm_runtime_resume+0x4a/0x90
__device_release_driver+0x28/0x240
device_release_driver+0x26/0x40
pci_stop_bus_device+0x68/0x90
pci_stop_bus_device+0x2c/0x90
pci_stop_and_remove_bus_device+0xe/0x20
pciehp_unconfigure_device+0x6c/0x110
pciehp_disable_slot+0x5b/0xe0
pciehp_handle_presence_or_link_change+0xc3/0x2f0
pciehp_ist+0x179/0x180
This lockdep warning is triggered because with Thunderbolt, hotplug ports
are nested. When removing multiple devices in a daisy-chain, each hotplug
port's reset_lock may be acquired recursively. It's never the same lock, so
the lockdep splat is a false positive.
Because locks at the same hierarchy level are never acquired recursively, a
per-level lockdep class is sufficient to fix the lockdep warning.
The choice to use one lockdep subclass per pcie-hotplug controller in the
path to the root-bus was made to conserve class keys because their number
is limited and the complexity grows quadratically with number of keys
according to Documentation/locking/lockdep-design.rst.
Link: https://lore.kernel.org/linux-pci/20190402021933.GA2966@mit.edu/
Link: https://lore.kernel.org/linux-pci/de684a28-9038-8fc6-27ca-3f6f2f6400d7@redhat.com/
Link: https://lore.kernel.org/r/20211217141709.379663-1-hdegoede@redhat.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208855
Reported-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
The functions get_max_adapter_speed() and get_bus_name() in ibmphp_core.c
are commented-out and the fields .get_max_adapter_speed and
.get_bus_name_status are removed from struct hotplug_slot_ops in
pci_hotplug.h. Remove the commented-out functions.
Link: https://lore.kernel.org/r/20211209213618.20522-1-makvihas@gmail.com
Signed-off-by: Vihas Mak <makvihas@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Power Fault Detected bit in the Slot Status register differs from
all other hotplug events in that it is sticky: It can only be cleared
after turning off slot power. Per PCIe r5.0, sec. 6.7.1.8:
If a power controller detects a main power fault on the hot-plug slot,
it must automatically set its internal main power fault latch [...].
The main power fault latch is cleared when software turns off power to
the hot-plug slot.
The stickiness used to cause interrupt storms and infinite loops which
were fixed in 2009 by commits 5651c48cfa ("PCI pciehp: fix power fault
interrupt storm problem") and 99f0169c17 ("PCI: pciehp: enable
software notification on empty slots").
Unfortunately in 2020 the infinite loop issue was inadvertently
reintroduced by commit 8edf5332c3 ("PCI: pciehp: Fix MSI interrupt
race"): The hardirq handler pciehp_isr() clears the PFD bit until
pciehp's power_fault_detected flag is set. That happens in the IRQ
thread pciehp_ist(), which never learns of the event because the hardirq
handler is stuck in an infinite loop. Fix by setting the
power_fault_detected flag already in the hardirq handler.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214989
Link: https://lore.kernel.org/linux-pci/DM8PR11MB5702255A6A92F735D90A4446868B9@DM8PR11MB5702.namprd11.prod.outlook.com
Fixes: 8edf5332c3 ("PCI: pciehp: Fix MSI interrupt race")
Link: https://lore.kernel.org/r/66eaeef31d4997ceea357ad93259f290ededecfd.1637187226.git.lukas@wunner.de
Reported-by: Joseph Bao <joseph.bao@intel.com>
Tested-by: Joseph Bao <joseph.bao@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
Cc: Stuart Hayes <stuart.w.hayes@gmail.com>
When config pci_ops.read() can detect failed PCI transactions, the data
returned to the CPU is PCI_ERROR_RESPONSE (~0 or 0xffffffff).
Obviously a successful PCI config read may *also* return that data if a
config register happens to contain ~0, so it doesn't definitively indicate
an error unless we know the register cannot contain ~0.
Use PCI_POSSIBLE_ERROR() to check the response we get when we read data
from hardware. This unifies PCI error response checking and makes error
checks consistent and easier to find.
Link: https://lore.kernel.org/r/b12005c0d57bb9d4c8b486724d078b7bd92f8321.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When config pci_ops.read() can detect failed PCI transactions, the data
returned to the CPU is PCI_ERROR_RESPONSE (~0 or 0xffffffff).
Obviously a successful PCI config read may *also* return that data if a
config register happens to contain ~0, so it doesn't definitively indicate
an error unless we know the register cannot contain ~0.
Use PCI_POSSIBLE_ERROR() to check the response we get when we read data
from hardware. This unifies PCI error response checking and makes error
checks consistent and easier to find.
Compile tested only.
Link: https://lore.kernel.org/r/e185b052fbfd530df703a36dd31126cb870eed95.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lukas Wunner <lukas@wunner.de>
This is done by adding a zpci_hot_reset_device() call which does a low
level reset of the PCI function without changing its higher level
function state. This way it can be used while the zPCI function is bound
to a driver and with DMA tables being controlled either through the
IOMMU or DMA APIs which is prohibited when using zpci_disable_device()
as that drop existing DMA translations.
As this reset, unlike a normal FLR, also calls zpci_clear_irq() we need
to implement arch_restore_msi_irqs() and make sure we re-enable IRQs for
the PCI function if they were previously disabled.
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
- Tidy setup-irq.c comments (Pranay Sanghai)
- Fix misspellings (Krzysztof Wilczyński)
- Fix sprintf(), sscanf() format mismatches (Krzysztof Wilczyński)
- Tidy cpqphp code formatting (Krzysztof Wilczyński)
- Remove unused pci_pool wrappers, which have been replaced by dma_pool
(Cai Huoqing)
- Remove a redundant initialization in __pci_reset_function_locked() (Colin
Ian King)
- Use 'unsigned int' instead of 'unsigned' (Krzysztof Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof Wilczyński)
- Include generic <linux/> headers instead of <asm/> for cpqphp and vmd
(Krzysztof Wilczyński)
* pci/misc:
PCI: vmd: Drop redundant includes of <asm/device.h>, <asm/msi.h>
PCI: cpqphp: Use <linux/io.h> instead of <asm/io.h>
MAINTAINERS: Update PCI subsystem information
PCI: Prefer 'unsigned int' over bare 'unsigned'
PCI: Remove redundant 'rc' initialization
PCI: Remove unused pci_pool wrappers
PCI: cpqphp: Format if-statement code block correctly
PCI: Use unsigned to match sscanf("%x") in pci_dev_str_match_path()
PCI: hv: Remove unnecessary use of %hx
PCI: Correct misspelled and remove duplicated words
PCI: Tidy comments
Use the preferred generic header file linux/io.h that already includes the
corresponding asm/io.h file.
Link: https://lore.kernel.org/r/20211013003145.1107148-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev>
Stuart Hayes reports that an error handled by DPC at a Root Port results
in pciehp gratuitously bringing down a subordinate hotplug port:
RP -- UP -- DP -- UP -- DP (hotplug) -- EP
pciehp brings the slot down because the Link to the Endpoint goes down.
That is caused by a Hot Reset being propagated as a result of DPC.
Per PCIe Base Spec 5.0, section 6.6.1 "Conventional Reset":
For a Switch, the following must cause a hot reset to be sent on all
Downstream Ports: [...]
* The Data Link Layer of the Upstream Port reporting DL_Down status.
In Switches that support Link speeds greater than 5.0 GT/s, the
Upstream Port must direct the LTSSM of each Downstream Port to the
Hot Reset state, but not hold the LTSSMs in that state. This permits
each Downstream Port to begin Link training immediately after its
hot reset completes. This behavior is recommended for all Switches.
* Receiving a hot reset on the Upstream Port.
Once DPC recovers, pcie_do_recovery() walks down the hierarchy and
invokes pcie_portdrv_slot_reset() to restore each port's config space.
At that point, a hotplug interrupt is signaled per PCIe Base Spec r5.0,
section 6.7.3.4 "Software Notification of Hot-Plug Events":
If the Port is enabled for edge-triggered interrupt signaling using
MSI or MSI-X, an interrupt message must be sent every time the logical
AND of the following conditions transitions from FALSE to TRUE: [...]
* The Hot-Plug Interrupt Enable bit in the Slot Control register is
set to 1b.
* At least one hot-plug event status bit in the Slot Status register
and its associated enable bit in the Slot Control register are both
set to 1b.
Prevent pciehp from gratuitously bringing down the slot by clearing the
error-induced Data Link Layer State Changed event before restoring
config space. Afterwards, check whether the link has unexpectedly
failed to retrain and synthesize a DLLSC event if so.
Allow each pcie_port_service_driver (one of them being pciehp) to define
a slot_reset callback and re-use the existing pm_iter() function to
iterate over the callbacks.
Thereby, the Endpoint driver remains bound throughout error recovery and
may restore the device to working state.
Surprise removal during error recovery is detected through a Presence
Detect Changed event. The hotplug port is expected to not signal that
event as a result of a Hot Reset.
The issue isn't DPC-specific, it also occurs when an error is handled by
AER through aer_root_reset(). So while the issue was noticed only now,
it's been around since 2006 when AER support was first introduced.
[bhelgaas: drop PCI_ERROR_RECOVERY Kconfig, split pm_iter() rename to
preparatory patch]
Link: https://lore.kernel.org/linux-pci/08c046b0-c9f2-3489-eeef-7e7aca435bb9@gmail.com/
Fixes: 6c2b374d74 ("PCI-Express AER implemetation: AER core and aerdriver")
Link: https://lore.kernel.org/r/251f4edcc04c14f873ff1c967bc686169cd07d2d.1627638184.git.lukas@wunner.de
Reported-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.19+: ba952824e6: PCI/portdrv: Report reset for frozen channel
Cc: Keith Busch <kbusch@kernel.org>
The code block related to the if-statement in cpqhp_set_irq() is
somewhat awkwardly formatted making the code hard to read.
Make it readable. No change to functionality intended.
Link: https://lore.kernel.org/r/20211013011412.1110829-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Correct a number of misspelled words and remove any words that were
duplicated in the PCI tree. No change to functionality intended.
Link: https://lore.kernel.org/r/20211006233827.147328-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since commit 2a671f77ee ("s390/pci: fix use after free of zpci_dev")
the reference count of a zpci_dev is incremented between
pcibios_add_device() and pcibios_release_device() which was supposed to
prevent the zpci_dev from being freed while the common PCI code has
access to it. It was missed however that the handling of zPCI
availability events assumed that once zpci_zdev_put() was called no
later availability event would still see the device. With the previously
mentioned commit however this assumption no longer holds and we must
make sure that we only drop the initial long-lived reference the zPCI
subsystem holds exactly once.
Do so by introducing a zpci_device_reserved() function that handles when
a device is reserved. Here we make sure the zpci_dev will not be
considered for further events by removing it from the zpci_list.
This also means that the device actually stays in the
ZPCI_FN_STATE_RESERVED state between the time we know it has been
reserved and the final reference going away. We thus need to consider it
a real state instead of just a conceptual state after the removal. The
final cleanup of PCI resources, removal from zbus, and destruction of
the IOMMU stays in zpci_release_device() to make sure holders of the
reference do see valid data until the release.
Fixes: 2a671f77ee ("s390/pci: fix use after free of zpci_dev")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Cache PCIe Device Capabilities register (Amey Narkhede)
- Add pcie_reset_flr() with 'probe' argument (Amey Narkhede)
- Add pdev->reset_methods[] array to track reset method ordering (Amey
Narkhede)
- Remove reset_fn field from pci_dev (Amey Narkhede)
- Add sysfs interface to query and set device reset mechanism (Amey
Narkhede)
- Add pci_set_acpi_fwnode() to set ACPI_COMPANION (Shanker Donthineni)
- Use acpi_pci_power_manageable() instead of duplicating logic (Shanker
Donthineni)
- Set ACPI fwnode early and at the same time with OF (Shanker Donthineni)
- Add support for ACPI _RST reset method (Shanker Donthineni)
- Change reset function 'probe' argument to bool (Amey Narkhede)
* pci/reset:
PCI: Change the type of probe argument in reset functions
PCI: Add support for ACPI _RST reset method
PCI: Setup ACPI fwnode early and at the same time with OF
PCI: Use acpi_pci_power_manageable()
PCI: Add pci_set_acpi_fwnode() to set ACPI_COMPANION
PCI: Allow userspace to query and set device reset mechanism
PCI: Remove reset_fn field from pci_dev
PCI: Add array to track reset method ordering
PCI: Add pcie_reset_flr() with 'probe' argument
PCI: Cache PCIe Device Capabilities register
ebda_rsrc_controller() calls iounmap(io_mem) on the error path. Its caller,
ibmphp_access_ebda(), also calls iounmap(io_mem) on good and error paths.
Remove the iounmap(io_mem) invocation from ebda_rsrc_controller().
[bhelgaas: remove item from TODO]
Link: https://lore.kernel.org/r/20210818165751.591185-1-os.vaslot@gmail.com
Signed-off-by: Vishal Aslot <os.vaslot@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Change the type of probe argument in functions which implement reset
methods from int to bool to make the context and intent clear.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-10-ameynarkhede03@gmail.com
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
cpci_debug is declared as a global variable in cpci_hotplug_core.c and used
in cpci_hotplug_pci.c via an "extern". Add an extern declaration in the
header file.
Resolves the following sparse warning:
drivers/pci/hotplug/cpci_hotplug_core.c:47:5: warning: symbol 'cpci_debug' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20210701184306.1492003-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Downstream Port Containment (PCIe r5.0, sec. 6.2.10) disables the link upon
an error and attempts to re-enable it when instructed by the DPC driver.
A slot which is both DPC- and hotplug-capable is currently powered off by
pciehp once DPC is triggered (due to the link change) and powered back up
on successful recovery. That's undesirable, the slot should remain powered
so the hotplugged device remains bound to its driver. DPC notifies the
driver of the error and of successful recovery in pcie_do_recovery() and
the driver may then restore the device to working state.
Moreover, Sinan points out that turning off slot power by pciehp may foil
recovery by DPC: Power off/on is a cold reset concurrently to DPC's warm
reset. Sathyanarayanan reports extended delays or failure in link
retraining by DPC if pciehp brings down the slot.
Fix by detecting whether a Link Down event is caused by DPC and awaiting
recovery if so. On successful recovery, ignore both the Link Down and the
subsequent Link Up event.
Afterwards, check whether the link is down to detect surprise-removal or
another DPC event immediately after DPC recovery. Ensure that the
corresponding DLLSC event is not ignored by synthesizing it and invoking
irq_wake_thread() to trigger a re-run of pciehp_ist().
The IRQ threads of the hotplug and DPC drivers, pciehp_ist() and
dpc_handler(), race against each other. If pciehp is faster than DPC, it
will wait until DPC recovery completes.
Recovery consists of two steps: The first step (waiting for link
disablement) is recognizable by pciehp through a set DPC Trigger Status
bit. The second step (waiting for link retraining) is recognizable through
a newly introduced PCI_DPC_RECOVERING flag.
If DPC is faster than pciehp, neither of the two flags will be set and
pciehp may glean the recovery status from the new PCI_DPC_RECOVERED flag.
The flag is zero if DPC didn't occur at all, hence DLLSC events are not
ignored by default.
pciehp waits up to 4 seconds before assuming that DPC recovery failed and
bringing down the slot. This timeout is not taken from the spec (it
doesn't mandate one) but based on a report from Yicong Yang that DPC may
take a bit more than 3 seconds on HiSilicon's Kunpeng platform.
The timeout is necessary because the DPC Trigger Status bit may never
clear: On Root Ports which support RP Extensions for DPC, the DPC driver
polls the DPC RP Busy bit for up to 1 second before giving up on DPC
recovery. Without the timeout, pciehp would then wait indefinitely for DPC
to complete.
This commit draws inspiration from previous attempts to synchronize DPC
with pciehp:
By Sinan Kaya, August 2018:
https://lore.kernel.org/linux-pci/20180818065126.77912-1-okaya@kernel.org/
By Ethan Zhao, October 2020:
https://lore.kernel.org/linux-pci/20201007113158.48933-1-haifeng.zhao@intel.com/
By Kuppuswamy Sathyanarayanan, March 2021:
https://lore.kernel.org/linux-pci/59cb30f5e5ac6d65427ceaadf1012b2ba8dbf66c.1615606143.git.sathyanarayanan.kuppuswamy@linux.intel.com/
Link: https://lore.kernel.org/r/0be565d97438fe2a6d57354b3aa4e8626952a00b.1619857124.git.lukas@wunner.de
Reported-by: Sinan Kaya <okaya@kernel.org>
Reported-by: Ethan Zhao <haifeng.zhao@intel.com>
Reported-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <kbusch@kernel.org>
The sysfs_emit() and sysfs_emit_at() functions were introduced to make
it less ambiguous which function is preferred when writing to the output
buffer in a device attribute's "show" callback [1].
Convert the PCI sysfs object "show" functions from sprintf(), snprintf()
and scnprintf() to sysfs_emit() and sysfs_emit_at() accordingly, as the
latter is aware of the PAGE_SIZE buffer and correctly returns the number
of bytes written into the buffer.
No functional change intended.
[1] Documentation/filesystems/sysfs.rst
Related commit: ad025f8e46 ("PCI/sysfs: Use sysfs_emit() and
sysfs_emit_at() in "show" functions").
Link: https://lore.kernel.org/r/20210603000112.703037-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
- add support for system call stack randomization.
- handle stale PCI deconfiguration events.
- couple of defconfig updates.
- some fixes and cleanups.
-----BEGIN PGP SIGNATURE-----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=C1HZ
-----END PGP SIGNATURE-----
Merge tag 's390-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Heiko Carstens:
- add support for system call stack randomization
- handle stale PCI deconfiguration events
- couple of defconfig updates
- some fixes and cleanups
* tag 's390-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix detection of vector enhancements facility 1 vs. vector packed decimal facility
s390/entry: add support for syscall stack randomization
s390/configs: change CONFIG_VIRTIO_CONSOLE to "m"
s390/cio: remove invalid condition on IO_SCH_UNREG
s390/cpumf: remove call to perf_event_update_userpage
s390/cpumf: move counter set size calculation to common place
s390/cpumf: beautify if-then-else indentation
s390/configs: enable CONFIG_PCI_IOV
s390/pci: handle stale deconfiguration events
s390/pci: rename zpci_configure_device()
With zpci_configure_device() now always called on a device that has
already been configured on the platform level its name has become
misleading. Rename it to zpci_scan_configured_device() to signify that
the function now only handles the correct scanning of a newly configured
PCI function taking care of the special handling necessary for function
0 and functions parked waiting for a PCI bus that can't be created
without first seeing function 0.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Currently zpci_configure_device() can be called on a zPCI function in
two completely different states. Either the underlying zPCI function has
already been configured by the platform and we are only doing the
scanning to get it usable by Linux drivers. Or the underlying function
is in Standby and we first do an SCLP to get it configured. This makes
zpci_configure_device() harder to reason about. Since calling
zpci_configure_device() on a function in Standby only happens in
enable_slot() simply pull out the SCLP call and setting of zdev->state
and thus call zpci_configure_device() under the same circumstances as
in the event handling code.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
In enable_slot(), if pci_get_slot() returns NULL, we clear the SLOT_ENABLED
flag. When pci_get_slot() finds a device, it increments the device's
reference count. In this case, we did not call pci_dev_put() to decrement
the reference count, so the memory of the device (struct pci_dev type) will
eventually leak.
Call pci_dev_put() to decrement its reference count when pci_get_slot()
returns a PCI device.
Link: https://lore.kernel.org/r/b411af88-5049-a1c6-83ac-d104a1f429be@huawei.com
Signed-off-by: Feilong Lin <linfeilong@huawei.com>
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A zPCI event with PEC 0x0301 for an existing zPCI device goes through
the same actions as enable_slot(). Similarly a zPCI event with PEC
0x0303 does the same steps as disable_slot().
We can thus unify both actions as zpci_configure_device() respectively
zpci_deconfigure_device().
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The current zdev->state mixes the configuration states supported by CLP
with an additional Online state which is used inconsistently to include
enabled zPCI functions which are not yet visible to the common PCI
subsytem. In preparation for a clean separation between architected
configuration states and fine grained function states remove the Online
function state.
Where we previously checked for Online it is more accurate to check if
the function is enabled to avoid an edge case where a disabled device
was still treated as Online. This also simplifies checks whether
a function is configured as this is now directly reflected by its
function state.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Fix a possible stack corruption and subsequent DLPAR failure in the rpadlpar_io
PCI hotplug driver.
Two build fixes for uncommon configurations.
Thanks to Christophe Leroy, Tyrel Datwyler.
-----BEGIN PGP SIGNATURE-----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=SHvi
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix a possible stack corruption and subsequent DLPAR failure in the
rpadlpar_io PCI hotplug driver
- Two build fixes for uncommon configurations
Thanks to Christophe Leroy and Tyrel Datwyler.
* tag 'powerpc-5.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
PCI: rpadlpar: Fix potential drc_name corruption in store functions
powerpc: Force inlining of cpu_has_feature() to avoid build failure
powerpc/vdso32: Add missing _restgpr_31_x to fix build failure
Both add_slot_store() and remove_slot_store() try to fix up the
drc_name copied from the store buffer by placing a NUL terminator at
nbyte + 1 or in place of a '\n' if present. However, the static buffer
that we copy the drc_name data into is not zeroed and can contain
anything past the n-th byte.
This is problematic if a '\n' byte appears in that buffer after nbytes
and the string copied into the store buffer was not NUL terminated to
start with as the strchr() search for a '\n' byte will mark this
incorrectly as the end of the drc_name string resulting in a drc_name
string that contains garbage data after the n-th byte.
Additionally it will cause us to overwrite that '\n' byte on the stack
with NUL, potentially corrupting data on the stack.
The following debugging shows an example of the drmgr utility writing
"PHB 4543" to the add_slot sysfs attribute, but add_slot_store()
logging a corrupted string value.
drmgr: drmgr: -c phb -a -s PHB 4543 -d 1
add_slot_store: drc_name = PHB 4543°|<82>!, rc = -19
Fix this by using strscpy() instead of memcpy() to ensure the string
is NUL terminated when copied into the static drc_name buffer.
Further, since the string is now NUL terminated the code only needs to
change '\n' to '\0' when present.
Cc: stable@vger.kernel.org
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
[mpe: Reformat change log and add mention of possible stack corruption]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210315214821.452959-1-tyreld@linux.ibm.com
In commit 05bc1be6db ("s390/pci: create zPCI bus") we removed the
pci_dev_put() call matching the earlier pci_get_slot() done as part of
__zpci_event_availability(). This was based on the wrong understanding
that the device_put() done as part of pci_destroy_device() would counter
the pci_get_slot() when it only counters the initial reference. This
same understanding and existing bad example also lead to not doing
a pci_dev_put() in zpci_remove_device().
Since releasing the PCI devices, unlike releasing the PCI slot, does not
print any debug message for testing I added one in pci_release_dev().
This revealed that we are indeed leaking the PCI device on PCI
hotunplug. Further testing also revealed another missing pci_dev_put() in
disable_slot().
Fix this by adding the missing pci_dev_put() in disable_slot() and fix
zpci_remove_device() with the correct pci_dev_put() calls. Also instead
of calling pci_get_slot() in __zpci_event_availability() to determine if
a PCI device is registered and then doing the same again in
zpci_remove_device() do this once in zpci_remove_device() which makes
sure that the pdev in __zpci_event_availability() is only used for the
result of pci_scan_single_device() which does not need a reference count
decremnt as its ownership goes to the PCI bus.
Also move the check if zdev->zbus->bus is set into zpci_remove_device()
since it may be that we're removing a device with devfn != 0 which never
had a PCI bus. So we can still set the pdev->error_state to indicate
that the device is not usable anymore, add a flag to set the error state.
Fixes: 05bc1be6db ("s390/pci: create zPCI bus")
Cc: <stable@vger.kernel.org> # 5.8+: e1bff843cd s390/pci: remove superfluous zdev->zbus check
Cc: <stable@vger.kernel.org> # 5.8+: ba764dd703 s390/pci: refactor zpci_create_device()
Cc: <stable@vger.kernel.org> # 5.8+
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Remove the 'acpiphp_callback' typedef as it is not used.
Link: https://lore.kernel.org/r/1613443120-4279-1-git-send-email-chen45464546@163.com
Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The value of the constant POWER_FAILURE assigned to the variable rc
after the power fault check is never used for anything, so remove it.
Addresses-Coverity-ID: 1226899 ("Unused value")
Link: https://lore.kernel.org/r/20200923025225.471459-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When a PCIe card is hot-removed, the Presence Detect State and Data Link
Layer Link Active bits often do not clear simultaneously. I've seen delays
of up to 244 msec between the two events with Thunderbolt.
After pciehp has brought down the slot in response to the first event, the
other bit may still be set. It's not discernible whether it's set because
a new card is already in the slot or if it will soon clear. So pciehp
tries to bring up the slot and in the latter case fails with a bunch of
messages, some of them at KERN_ERR severity. If the slot is no longer
occupied, the messages are false positives and annoy users.
Stuart Hayes reports the following splat on hot removal:
KERN_INFO pcieport 0000:3c:06.0: pciehp: Slot(180): Link Up
KERN_INFO pcieport 0000:3c:06.0: pciehp: Timeout waiting for Presence Detect
KERN_ERR pcieport 0000:3c:06.0: pciehp: link training error: status 0x0001
KERN_ERR pcieport 0000:3c:06.0: pciehp: Failed to check link status
Dongdong Liu complains about a similar splat:
KERN_INFO pciehp 0000:80:10.0:pcie004: Slot(36): Link Down
KERN_INFO iommu: Removing device 0000:87:00.0 from group 12
KERN_INFO pciehp 0000:80:10.0:pcie004: Slot(36): Card present
KERN_INFO pcieport 0000:80:10.0: Data Link Layer Link Active not set in 1000 msec
KERN_ERR pciehp 0000:80:10.0:pcie004: Failed to check link status
Users are particularly irritated to see a bringup attempt even though the
slot was explicitly brought down via sysfs. In a perfect world, we could
avoid this by setting Link Disable on slot bringdown and re-enabling it
upon a Presence Detect State change. In reality however, there are broken
hotplug ports which hardwire Presence Detect to zero, see 80696f9914
("PCI: pciehp: Tolerate Presence Detect hardwired to zero"). Conversely,
PCIe r1.0 hotplug ports hardwire Link Active to zero because Link Active
Reporting wasn't specified before PCIe r1.1. On unplug, some ports first
clear Presence then Link (see Stuart Hayes' splat) whereas others use the
inverse order (see Dongdong Liu's splat). To top it off, there are hotplug
ports which flap the Presence and Link bits on slot bringup, see
6c35a1ac3d ("PCI: pciehp: Tolerate initially unstable link").
pciehp is designed to work with all of these variants. Surplus attempts at
slot bringup are a lesser evil than not being able to bring up slots at
all. Although we could try to perfect the behavior for specific hotplug
controllers, we'd risk breaking others or increasing code complexity.
But we can certainly minimize annoyance by emitting only a single message
with KERN_INFO severity if bringup is unsuccessful:
* Drop the "Timeout waiting for Presence Detect" message in
pcie_wait_for_presence(). The sole caller of that function,
pciehp_check_link_status(), ignores the timeout and carries on. It emits
error messages of its own and I don't think this particular message adds
much value.
* There's a single error condition in pciehp_check_link_status() which
does not emit a message. Adding one allows dropping the "Failed to check
link status" message emitted by board_added() if
pciehp_check_link_status() returns a non-zero integer.
* Tone down all messages in pciehp_check_link_status() to KERN_INFO
severity and rephrase them to look as innocuous as possible. To this
end, move the message emitted by pcie_wait_for_link_delay() to its
callers.
As a result, Stuart Hayes' splat becomes:
KERN_INFO pcieport 0000:3c:06.0: pciehp: Slot(180): Link Up
KERN_INFO pcieport 0000:3c:06.0: pciehp: Slot(180): Cannot train link: status 0x0001
Dongdong Liu's splat becomes:
KERN_INFO pciehp 0000:80:10.0:pcie004: Slot(36): Card present
KERN_INFO pciehp 0000:80:10.0:pcie004: Slot(36): No link
The messages now merely serve as information that presence or link bits
were set a little longer than expected. Bringup failures which are not
false positives are still reported, albeit no longer at KERN_ERR severity.
Link: https://lore.kernel.org/linux-pci/20200310182100.102987-1-stuart.w.hayes@gmail.com/
Link: https://lore.kernel.org/linux-pci/1547649064-19019-1-git-send-email-liudongdong3@huawei.com/
Link: https://lore.kernel.org/r/b45e46fd8a6aa6930aaac9d7718c2e4b787a4e5e.1595935071.git.lukas@wunner.de
Reported-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Reported-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For fixing the PF to VF link removal we need to perform some action on
every removal of a zdev from the common PCI subsystem.
So in preparation re-introduce zpci_remove_device() and use that instead
of directly calling the common code functions. This was actually still
declared from earlier code but no longer implemented.
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The sparse tool report build warnings as follows:
drivers/pci/hotplug/rpadlpar_core.c:355:5: warning: symbol 'dlpar_remove_pci_slot' was not declared. Should it be static?
drivers/pci/hotplug/rpadlpar_core.c:461:12: warning: symbol 'rpadlpar_io_init' was not declared. Should it be static?
drivers/pci/hotplug/rpadlpar_core.c:473:6: warning: symbol 'rpadlpar_io_exit' was not declared. Should it be static?
Those functions are not used outside of this file, so mark them static.
Also mark rpadlpar_io_exit() as __exit.
Link: https://lore.kernel.org/r/20200721151735.41181-1-weiyongjun1@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If context is not NULL in acpiphp_grab_context(), but the
is_going_away flag is set for the device's parent, the reference
counter of the context needs to be decremented before returning
NULL or the context will never be freed, so make that happen.
Fixes: edf5bf34d4 ("ACPI / dock: Use callback pointers from devices' ACPI hotplug contexts")
Reported-by: Vasily Averin <vvs@virtuozzo.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the
pdev->no_vf_scan flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio
and qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl7eVGcACgkQjYWKoQLX
FBhweQgAkicvx31x230rdfG+jQkQkl0UqF99vvWrJHEll77SqadfjzKAGIjUB+K0
EoeHVD5Wcj7BogDGcyHeQ0bZpu4WzE+y1nmnrsvu7TEEvcBmkJH0rF2jF+y0sb/O
3qvwFkX/CB5OqaMzKC/AEeRpcCKR+ZUXkWu1irbYth7CBXaycD9EAPc4cj8CfYGZ
r5njUdYOVk77TaO4aV+t5pCYc5TCRJaWXSsWaAv/nuLcIqsFBYOy2q+L47zITGXp
utZVanIDjzx+ikpaKicOIfC3hJsRuNX9MnlZKsQFwpVEZAUZmIUm29XdhGJTWSxU
RV7m1ORINbFP1nGAqWqkOvGo/LC0ZA==
=VhXR
-----END PGP SIGNATURE-----
Merge tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the pdev->no_vf_scan
flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio and
qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
* tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (52 commits)
vfio-ccw: make vfio_ccw_regops variables declarations static
vfio-ccw: Add trace for CRW event
vfio-ccw: Wire up the CRW irq and CRW region
vfio-ccw: Introduce a new CRW region
vfio-ccw: Refactor IRQ handlers
vfio-ccw: Introduce a new schib region
vfio-ccw: Refactor the unregister of the async regions
vfio-ccw: Register a chp_event callback for vfio-ccw
vfio-ccw: Introduce new helper functions to free/destroy regions
vfio-ccw: document possible errors
vfio-ccw: Enable transparent CCW IPL from DASD
s390/pci: Log new handle in clp_disable_fh()
s390/cio, s390/qeth: cleanup PNSO CHSC
s390/qdio: remove q->first_to_kick
s390/qdio: fix up qdio_start_irq() kerneldoc
s390: remove critical section cleanup from entry.S
s390: add machine check SIGP
s390/pci: ioremap() align with generic code
s390/ap: introduce new ap function ap_get_qdev()
Documentation/s390: Update / remove developerWorks web links
...
- Update the ACPICA code in the kernel to upstream revision
20200430:
* Move acpi_gbl_next_cmd_num definition (Erik Kaneda).
* Ignore AE_ALREADY_EXISTS status in the disassembler when parsing
create operators (Erik Kaneda).
* Add status checks to the dispatcher (Erik Kaneda).
* Fix required parameters for _NIG and _NIH (Erik Kaneda).
* Make acpi_protocol_lengths static (Yue Haibing).
- Fix ACPI table reference counting errors in several places, mostly
in error code paths (Hanjun Guo).
- Extend the Generic Event Device (GED) driver to support _Exx and
_Lxx handler methods (Ard Biesheuvel).
- Add new acpi_evaluate_reg() helper and modify the ACPI PCI hotplug
code to use it (Hans de Goede).
- Add new DPTF battery participant driver and make the DPFT power
participant driver create more sysfs device attributes (Srinivas
Pandruvada).
- Improve the handling of memory failures in APEI (James Morse).
- Add new blacklist entry for Acer TravelMate 5735Z to the backlight
driver (Paul Menzel).
- Add i2c address for thermal control to the PMIC driver (Mauro
Carvalho Chehab).
- Allow the ACPI processor idle driver to work on platforms with
only one ACPI C-state present (Zhang Rui).
- Fix kobject reference count leaks in error code paths in two
places (Qiushi Wu).
- Delete unused proc filename macros and make some symbols static
(Pascal Terjan, Zheng Zengkai, Zou Wei).
-----BEGIN PGP SIGNATURE-----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=xH3i
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20200430, fix several reference counting errors related to ACPI
tables, add _Exx / _Lxx support to the GED driver, add a new
acpi_evaluate_reg() helper, add new DPTF battery participant driver
and extend the DPFT power participant driver, improve the handling of
memory failures in the APEI code, add a blacklist entry to the
backlight driver, update the PMIC driver and the processor idle
driver, fix two kobject reference count leaks, and make a few janitory
changes.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20200430:
- Move acpi_gbl_next_cmd_num definition (Erik Kaneda).
- Ignore AE_ALREADY_EXISTS status in the disassembler when parsing
create operators (Erik Kaneda).
- Add status checks to the dispatcher (Erik Kaneda).
- Fix required parameters for _NIG and _NIH (Erik Kaneda).
- Make acpi_protocol_lengths static (Yue Haibing).
- Fix ACPI table reference counting errors in several places, mostly
in error code paths (Hanjun Guo).
- Extend the Generic Event Device (GED) driver to support _Exx and
_Lxx handler methods (Ard Biesheuvel).
- Add new acpi_evaluate_reg() helper and modify the ACPI PCI hotplug
code to use it (Hans de Goede).
- Add new DPTF battery participant driver and make the DPFT power
participant driver create more sysfs device attributes (Srinivas
Pandruvada).
- Improve the handling of memory failures in APEI (James Morse).
- Add new blacklist entry for Acer TravelMate 5735Z to the backlight
driver (Paul Menzel).
- Add i2c address for thermal control to the PMIC driver (Mauro
Carvalho Chehab).
- Allow the ACPI processor idle driver to work on platforms with only
one ACPI C-state present (Zhang Rui).
- Fix kobject reference count leaks in error code paths in two places
(Qiushi Wu).
- Delete unused proc filename macros and make some symbols static
(Pascal Terjan, Zheng Zengkai, Zou Wei)"
* tag 'acpi-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
ACPI: CPPC: Fix reference count leak in acpi_cppc_processor_probe()
ACPI: sysfs: Fix reference count leak in acpi_sysfs_add_hotplug_profile()
ACPI: GED: use correct trigger type field in _Exx / _Lxx handling
ACPI: DPTF: Add battery participant driver
ACPI: DPTF: Additional sysfs attributes for power participant driver
ACPI: video: Use native backlight on Acer TravelMate 5735Z
arm64: acpi: Make apei_claim_sea() synchronise with APEI's irq work
ACPI: APEI: Kick the memory_failure() queue for synchronous errors
mm/memory-failure: Add memory_failure_queue_kick()
ACPI / PMIC: Add i2c address for thermal control
ACPI: GED: add support for _Exx / _Lxx handler methods
ACPI: Delete unused proc filename macros
ACPI: hotplug: PCI: Use the new acpi_evaluate_reg() helper
ACPI: utils: Add acpi_evaluate_reg() helper
ACPI: debug: Make two functions static
ACPI: sleep: Put the FACS table after using it
ACPI: scan: Put SPCR and STAO table after using it
ACPI: EC: Put the ACPI table after using it
ACPI: APEI: Put the HEST table for error path
ACPI: APEI: Put the error record serialization table for error path
...
shpchp_unconfigure_device() always returned 0, so there's no reason for a
return value. In addition, remove_board() checked the return value for
possible error which is unnecessary.
Convert shpchp_unconfigure_device() to a void function and remove the
return value check. This addresses the following Coccinelle warning:
drivers/pci/hotplug/shpchp_pci.c:66:5-7: Unneeded variable: "rc". Return "0" on line 86
Link: https://lore.kernel.org/r/20200521190457.1066600-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the new acpi_evaluate_reg() helper in the acpiphp_glue.c code.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Physical function should not be disabled until no virtual
functions depends on it.
Let's force the user to first use echo 0 > sriov_numfs before
allowing to disable the PF with echo 0 > power.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
We allow multiple functions on a single bus.
We suppress the ZPCI_DEVFN definition and replace its
occurences with zpci->devfn.
We verify the number of device during the registration.
There can never be more domains in use than existing
devices, so we do not need to verify the count of domain
after having verified the count of devices.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The zPCI bus is in charge to handle common zPCI resources for
zPCI devices.
Creating the zPCI bus, the PCI bus, the zPCI devices and the
PCI devices and hotplug slots
done in a specific order:
- PCI hotplug slot creation needs a PCI bus
- PCI bus needs a PCI domain
which is reported by the pci_domain_nr() when setting up the
host bridge
- PCI domain is set from the zPCI with devfn 0
this is necessary to have a reproducible enumeration
Therefore we can not create devices or hotplug slots for any PCI
device associated with a zPCI device before having discovered
the function zero of the bus.
The discovery and initialization of devices can be done at several
points in the code:
- On Events, serialized in a thread context
- On initialization, in the kernel init thread context
- When powering on the hotplug slot, in a user thread context
The removal of devices and their parent bus may also be done on
events or for devices when powering down the slot.
To guarantee the existence of the bus and devices until they are
no more needed we use kref in zPCI bus and introduce a reference
count in the zPCI devices.
In this patch the zPCI bus still only accept a device with
a devfn 0.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Convert string compares of DT node names to use of_node_name_eq() helper
instead. This removes direct access to the node name pointer.
Link: https://lore.kernel.org/r/20200416215114.7715-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Because all callers of dev_pm_smart_suspend_and_suspended use it only
for checking whether or not to skip driver suspend callbacks for a
device, rename it to dev_pm_skip_suspend() in analogy with
dev_pm_skip_resume().
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
- A large series from Nick for 64-bit to further rework our exception vectors,
and rewrite portions of the syscall entry/exit and interrupt return in C. The
result is much easier to follow code that is also faster in general.
- Cleanup of our ptrace code to split various parts out that had become badly
intertwined with #ifdefs over the years.
- Changes to our NUMA setup under the PowerVM hypervisor which should
hopefully avoid non-sensical topologies which can lead to warnings from the
workqueue code and other problems.
- MAINTAINERS updates to remove some of our old orphan entries and update the
status of others.
- Quite a few other small changes and fixes all over the map.
Thanks to:
Abdul Haleem, afzal mohammed, Alexey Kardashevskiy, Andrew Donnellan, Aneesh
Kumar K.V, Balamuruhan S, Cédric Le Goater, Chen Zhou, Christophe JAILLET,
Christophe Leroy, Christoph Hellwig, Clement Courbet, Daniel Axtens, David
Gibson, Douglas Miller, Fabiano Rosas, Fangrui Song, Ganesh Goudar, Gautham R.
Shenoy, Greg Kroah-Hartman, Greg Kurz, Gustavo Luiz Duarte, Hari Bathini, Ilie
Halip, Jan Kara, Joe Lawrence, Joe Perches, Kajol Jain, Larry Finger,
Laurentiu Tudor, Leonardo Bras, Libor Pechacek, Madhavan Srinivasan, Mahesh
Salgaonkar, Masahiro Yamada, Masami Hiramatsu, Mauricio Faria de Oliveira,
Michael Neuling, Michal Suchanek, Mike Rapoport, Nageswara R Sastry, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers,
Oliver O'Halloran, Po-Hsu Lin, Pratik Rajesh Sampat, Rasmus Villemoes, Ravi
Bangoria, Roman Bolshakov, Sam Bobroff, Sandipan Das, Santosh S, Sedat Dilek,
Segher Boessenkool, Shilpasri G Bhat, Sourabh Jain, Srikar Dronamraju, Stephen
Rothwell, Tyrel Datwyler, Vaibhav Jain, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=ARdm
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Slightly late as I had to rebase mid-week to insert a bug fix:
- A large series from Nick for 64-bit to further rework our exception
vectors, and rewrite portions of the syscall entry/exit and
interrupt return in C. The result is much easier to follow code
that is also faster in general.
- Cleanup of our ptrace code to split various parts out that had
become badly intertwined with #ifdefs over the years.
- Changes to our NUMA setup under the PowerVM hypervisor which should
hopefully avoid non-sensical topologies which can lead to warnings
from the workqueue code and other problems.
- MAINTAINERS updates to remove some of our old orphan entries and
update the status of others.
- Quite a few other small changes and fixes all over the map.
Thanks to: Abdul Haleem, afzal mohammed, Alexey Kardashevskiy, Andrew
Donnellan, Aneesh Kumar K.V, Balamuruhan S, Cédric Le Goater, Chen
Zhou, Christophe JAILLET, Christophe Leroy, Christoph Hellwig, Clement
Courbet, Daniel Axtens, David Gibson, Douglas Miller, Fabiano Rosas,
Fangrui Song, Ganesh Goudar, Gautham R. Shenoy, Greg Kroah-Hartman,
Greg Kurz, Gustavo Luiz Duarte, Hari Bathini, Ilie Halip, Jan Kara,
Joe Lawrence, Joe Perches, Kajol Jain, Larry Finger, Laurentiu Tudor,
Leonardo Bras, Libor Pechacek, Madhavan Srinivasan, Mahesh Salgaonkar,
Masahiro Yamada, Masami Hiramatsu, Mauricio Faria de Oliveira, Michael
Neuling, Michal Suchanek, Mike Rapoport, Nageswara R Sastry, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Nick
Desaulniers, Oliver O'Halloran, Po-Hsu Lin, Pratik Rajesh Sampat,
Rasmus Villemoes, Ravi Bangoria, Roman Bolshakov, Sam Bobroff,
Sandipan Das, Santosh S, Sedat Dilek, Segher Boessenkool, Shilpasri G
Bhat, Sourabh Jain, Srikar Dronamraju, Stephen Rothwell, Tyrel
Datwyler, Vaibhav Jain, YueHaibing"
* tag 'powerpc-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (158 commits)
powerpc: Make setjmp/longjmp signature standard
powerpc/cputable: Remove unnecessary copy of cpu_spec->oprofile_type
powerpc: Suppress .eh_frame generation
powerpc: Drop -fno-dwarf2-cfi-asm
powerpc/32: drop unused ISA_DMA_THRESHOLD
powerpc/powernv: Add documentation for the opal sensor_groups sysfs interfaces
selftests/powerpc: Fix try-run when source tree is not writable
powerpc/vmlinux.lds: Explicitly retain .gnu.hash
powerpc/ptrace: move ptrace_triggered() into hw_breakpoint.c
powerpc/ptrace: create ppc_gethwdinfo()
powerpc/ptrace: create ptrace_get_debugreg()
powerpc/ptrace: split out ADV_DEBUG_REGS related functions.
powerpc/ptrace: move register viewing functions out of ptrace.c
powerpc/ptrace: split out TRANSACTIONAL_MEM related functions.
powerpc/ptrace: split out SPE related functions.
powerpc/ptrace: split out ALTIVEC related functions.
powerpc/ptrace: split out VSX related functions.
powerpc/ptrace: drop PARAMETER_SAVE_AREA_OFFSET
powerpc/ptrace: drop unnecessary #ifdefs CONFIG_PPC64
powerpc/ptrace: remove unused header includes
...
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth Vijayan
common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other fixes/improvements
in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios
mm cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl6Ig2YACgkQjYWKoQLX
FBj2gggAibnHOl9d0ngX1mVT4nz51R3V8z5sEQjNMr2uHBmaTqs7pi/00gaFMxoC
NngVEXvL443jSogQivthGgXPpRCV9xdKE3sp38j7fF4LgHoeuDtGd1oaX4W9Rqk0
7Yii35EaO2e2WHdOKaAbu+ZvDRunFjERyntc51MYaIUivFosogSo07vC73vFIArF
VGStS09fJ4Ny76ott896T7Ulx1Iek/MkF1vponEMLGNUIcLIQbbxZxOwgz0pHuEF
SlyyJBnhOIaAJGOYlKREQDt1cew+hsxluPU+a01bwdsmdZv9LH1BGwLayDqTH58i
QWvtEpzJFmDvo9jGM1v81ebaGnyCKg==
=hiGF
-----END PGP SIGNATURE-----
Merge tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth
Vijayan common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other
fixes/improvements in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios mm
cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
* tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (57 commits)
s390/mm: cleanup init_new_context() callback
s390/mm: cleanup virtual memory constants usage
s390/mm: remove page table downgrade support
s390/qdio: set qdio_irq->cdev at allocation time
s390/qdio: remove unused function declarations
s390/ccwgroup: remove pm support
s390/ap: remove power management code from ap bus and drivers
s390/zcrypt: use kvmalloc instead of kmalloc for 256k alloc
s390/mm: cleanup arch_get_unmapped_area() and friends
s390/ism: remove pm support
s390/cio: use fallthrough;
s390/vfio: use fallthrough;
s390/zcrypt: use fallthrough;
s390: use fallthrough;
s390/cpum_sf: Fix wrong page count in error message
s390/diag: fix display of diagnose call statistics
s390/ap: Remove ap device suspend and resume callbacks
s390/pci: Improve handling of unset UID
s390/pci: Fix zpci_alloc_domain() over allocation
s390/qdio: pass ISC as parameter to chsc_sadc()
...
Without this commit, a PCIe hotplug port can stop generating interrupts on
hotplug events, so device adds and removals will not be seen:
The pciehp interrupt handler pciehp_isr() reads the Slot Status register
and then writes back to it to clear the bits that caused the interrupt. If
a different interrupt event bit gets set between the read and the write,
pciehp_isr() returns without having cleared all of the interrupt event
bits. If this happens when the MSI isn't masked (which by default it isn't
in handle_edge_irq(), and which it will never be when MSI per-vector
masking is not supported), we won't get any more hotplug interrupts from
that device.
That is expected behavior, according to the PCIe Base Spec r5.0, section
6.7.3.4, "Software Notification of Hot-Plug Events".
Because the Presence Detect Changed and Data Link Layer State Changed event
bits can both get set at nearly the same time when a device is added or
removed, this is more likely to happen than it might seem. The issue was
found (and can be reproduced rather easily) by connecting and disconnecting
an NVMe storage device on at least one system model where the NVMe devices
were being connected to an AMD PCIe port (PCI device 0x1022/0x1483).
Fix the issue by modifying pciehp_isr() to loop back and re-read the Slot
Status register immediately after writing to it, until it sees that all of
the event status bits have been cleared.
[lukas: drop loop count limitation, write "events" instead of "status",
don't loop back in INTx and poll modes, tweak code comment & commit msg]
Link: https://lore.kernel.org/r/78b4ced5072bfe6e369d20e8b47c279b8c7af12e.1582121613.git.lukas@wunner.de
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
David Hoyer reports that powering pciehp slots up or down via sysfs may
hang: The call to wait_event() in pciehp_sysfs_enable_slot() and
_disable_slot() does not return because ctrl->ist_running remains true.
This flag, which was introduced by commit 157c1062fc ("PCI: pciehp: Avoid
returning prematurely from sysfs requests"), signifies that the IRQ thread
pciehp_ist() is running. It is set to true at the top of pciehp_ist() and
reset to false at the end. However there are two additional return
statements in pciehp_ist() before which the commit neglected to reset the
flag to false and wake up waiters for the flag.
That omission opens up the following race when powering up the slot:
* pciehp_ist() runs because a PCI_EXP_SLTSTA_PDC event was requested
by pciehp_sysfs_enable_slot()
* pciehp_ist() turns on slot power via the following call stack:
pciehp_handle_presence_or_link_change() -> pciehp_enable_slot() ->
__pciehp_enable_slot() -> board_added() -> pciehp_power_on_slot()
* after slot power is turned on, the link comes up, resulting in a
PCI_EXP_SLTSTA_DLLSC event
* the IRQ handler pciehp_isr() stores the event in ctrl->pending_events
and returns IRQ_WAKE_THREAD
* the IRQ thread is already woken (it's bringing up the slot), but the
genirq code remembers to re-run the IRQ thread after it has finished
(such that it can deal with the new event) by setting IRQTF_RUNTHREAD
via __handle_irq_event_percpu() -> __irq_wake_thread()
* the IRQ thread removes PCI_EXP_SLTSTA_DLLSC from ctrl->pending_events
via board_added() -> pciehp_check_link_status() in order to deal with
presence and link flaps per commit 6c35a1ac3d ("PCI: pciehp:
Tolerate initially unstable link")
* after pciehp_ist() has successfully brought up the slot, it resets
ctrl->ist_running to false and wakes up the sysfs requester
* the genirq code re-runs pciehp_ist(), which sets ctrl->ist_running
to true but then returns with IRQ_NONE because ctrl->pending_events
is empty
* pciehp_sysfs_enable_slot() is finally woken but notices that
ctrl->ist_running is true, hence continues waiting
The only way to get the hung task going again is to trigger a hotplug
event which brings down the slot, e.g. by yanking out the card.
The same race exists when powering down the slot because remove_board()
likewise clears link or presence changes in ctrl->pending_events per commit
3943af9d01 ("PCI: pciehp: Ignore Link State Changes after powering off a
slot") and thereby may cause a re-run of pciehp_ist() which returns with
IRQ_NONE without resetting ctrl->ist_running to false.
Fix by adding a goto label before the teardown steps at the end of
pciehp_ist() and jumping to that label from the two return statements which
currently neglect to reset the ctrl->ist_running flag.
Fixes: 157c1062fc ("PCI: pciehp: Avoid returning prematurely from sysfs requests")
Link: https://lore.kernel.org/r/cca1effa488065cb055120aa01b65719094bdcb5.1584530321.git.lukas@wunner.de
Reported-by: David Hoyer <David.Hoyer@netapp.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Cc: stable@vger.kernel.org # v4.19+
The eeh_ops->probe() function is called from two different contexts:
1. On pseries, where we set EEH_PROBE_MODE_DEVTREE, it's called in
eeh_add_device_early() which is supposed to run before we create
a pci_dev.
2. On PowerNV, where we set EEH_PROBE_MODE_DEV, it's called in
eeh_device_add_late() which is supposed to run *after* the
pci_dev is created.
The "early" probe is required because PAPR requires that we perform an RTAS
call to enable EEH support on a device before we start interacting with it
via config space or MMIO. This requirement doesn't exist on PowerNV and
shoehorning two completely separate initialisation paths into a common
interface just results in a convoluted code everywhere.
Additionally the early probe requires the probe function to take an pci_dn
rather than a pci_dev argument. We'd like to make pci_dn a pseries specific
data structure since there's no real requirement for them on PowerNV. To
help both goals move the early probe into the pseries containment zone
so the platform depedence is more explicit.
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-5-oohall@gmail.com
The pci hotplug helper (pci_hp_add_devices()) calls
eeh_add_device_tree_early() to scan the device-tree for new PCI devices and
do the early EEH probe before the device is scanned. This early probe is a
no-op in a lot of cases because:
a) The early init is only required to satisfy a PAPR requirement that EEH
be configured before we start doing config accesses. On PowerNV it is
a no-op.
b) It's a no-op for devices that have already had their eeh_dev
initialised.
There are four callers of pci_hp_add_devices():
1. arch/powerpc/kernel/eeh_driver.c
Here the hotplug helper is called when re-scanning pci_devs that
were removed during an EEH recovery pass. The EEH stat for each
removed device (the eeh_dev) is retained across a recovery pass
so the early init is a no-op in this case.
2. drivers/pci/hotplug/pnv_php.c
This is also a no-op since the PowerNV hotplug driver is, suprisingly,
PowerNV specific.
3. drivers/pci/hotplug/rpaphp_core.c
4. drivers/pci/hotplug/rpaphp_pci.c
In these two cases new devices have been hotplugged and FW has
provided new DT nodes for each. These are the only two cases where
the EEH we might have new PCI device nodes in the DT so these are
the only two cases where the early EEH probe needs to be done.
We can move the calls to eeh_add_device_tree_early() to the locations where
it's needed and remove it from the generic path. This is preparation for
making the early EEH probe pseries specific.
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-3-oohall@gmail.com
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/pci/hotplug/rpaphp_core.c: In function is_php_type:
drivers/pci/hotplug/rpaphp_core.c:291:16: warning:
variable value set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200312140412.32373-1-chenzhou10@huawei.com
Embedding the hotplug_slot in zdev structure allows to
greatly simplify the hotplug handling by eliminating
the handling of the slot_list.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Some systems have in-band presence detection disabled for hot-plug PCI
slots but do not report this in the slot capabilities 2 (SLTCAP2) register.
On these systems, presence detect can become active well after the link is
reported to be active, which can cause the slots to be disabled after a
device is connected.
Add a DMI table to flag these systems as having in-band presence detect
disabled.
Link: https://lore.kernel.org/r/20191025190047.38130-4-stuart.w.hayes@gmail.com
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
When in-band presence detect is disabled, PDS may come up at any time or
not at all. PDS being low may indicate that the card is still mating, and
we could expect contact bounce to bring down the link as well.
It is reasonable to assume that most cards will mate in a hotplug slot in
about a second. Thus, when we know PDS only reflects out-of-band presence
detect, it's worthwhile to wait the extra second or so to make sure the
card is properly mated before loading the driver and to prevent the hotplug
code from disabling a device if the presence detect change goes active
after the device is enabled.
Link: https://lore.kernel.org/r/20191025190047.38130-3-stuart.w.hayes@gmail.com
[bhelgaas: use ctrl_info() instead of pci_info()]
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
The presence detect state (PDS) is normally a logical OR of in-band and
out-of-band (OOB) presence detect. As of PCIe 4.0, there is the option to
disable in-band presence so that the PDS bit always reflects the state of
the out-of-band presence.
The recommendation of the PCIe spec is to disable in-band presence whenever
supported (PCIe r5.0, appendix I implementation note):
Due to architectural issues, the in-band (Physical-Layer-based) portion
of the PD mechanism is deprecated for use with async hot-plug. One issue
is that in-band PD as architected does not detect adapter removal during
certain LTSSM states, notably the L1 and Disabled States. Another issue
is that when both in-band and OOB PD are being used together, the
Presence Detect State bit and its associated interrupt mechanism always
reflect the logical OR of the inband and OOB PD states, and with some
hot-plug hardware configurations, it is important for software to detect
and respond to in-band and OOB PD events independently. If OOB PD is
being used and the associated DSP supports In-Band PD Disable, it is
recommended that the In-Band PD Disable bit be Set, and the Presence
Detect State bit and its associated interrupt mechanism be used
exclusively for OOB PD. As a substitute for in-band PD with async
hot-plug, the reference model uses either the DPC or the DLL Link Active
mechanism.
Link: https://lore.kernel.org/r/20191025190047.38130-2-stuart.w.hayes@gmail.com
[bhelgaas: move PCI_EXP_SLTCAP2 read earlier & print PCI_EXP_SLTCAP2_IBPD
value (suggested by Lukas)]
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
An opencapi slot doesn't have an associated bridge device. It's not
needed for operation, but any warning is displayed through pci_warn()
which uses the pci_dev struct of the assocated bridge device. So wrap
those warning so that a different trace mechanism can be used if it's
an opencapi slot.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-11-fbarrat@linux.ibm.com
The driver only allows to disable a slot in the POPULATED
state. However, if an error occurs while enabling the slot, say
because the link couldn't be trained, then the POPULATED state may not
be reached, yet the power state of the slot is on. So allow to disable
a slot in the REGISTERED state. Removing the devices will do nothing
since it's not populated, and we'll set the power state of the slot
back to off.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-10-fbarrat@linux.ibm.com
Add the opencapi PHBs to the list of PHBs being scanned to look for
slots.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-9-fbarrat@linux.ibm.com
When changing the slot state, if opal hits an error and tells as such
in the asynchronous reply, the warning "Wrong msg" is logged, which is
rather confusing. Instead we can reuse the better message which is
already used when we couldn't submit the asynchronous opal request
initially.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-8-fbarrat@linux.ibm.com
On powernv, when removing a device through hotplug, the following
warning is logged:
Invalid refcount <.> on <...>
It may be incorrect, the refcount may be set to a higher value than 1
and be valid. of_detach_node() can drop more than one reference. As it
doesn't seem trivial to assert the correct value, let's remove the
warning.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-7-fbarrat@linux.ibm.com
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
[bhelgaas: do same in vmd.c]
Link: https://lore.kernel.org/r/20191120134036.14502-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Valerio and others reported that commit 84c8b58ed3 ("ACPI / hotplug /
PCI: Don't scan bridges managed by native hotplug") prevents some recent
LG and HP laptops from booting with endless loop of:
ACPI Error: No handler or method for GPE 08, disabling event (20190215/evgpe-835)
ACPI Error: No handler or method for GPE 09, disabling event (20190215/evgpe-835)
ACPI Error: No handler or method for GPE 0A, disabling event (20190215/evgpe-835)
...
What seems to happen is that during boot, after the initial PCI enumeration
when EC is enabled the platform triggers ACPI Notify() to one of the root
ports. The root port itself looks like this:
pci 0000:00:1b.0: PCI bridge to [bus 02-3a]
pci 0000:00:1b.0: bridge window [mem 0xc4000000-0xda0fffff]
pci 0000:00:1b.0: bridge window [mem 0x80000000-0xa1ffffff 64bit pref]
The BIOS has configured the root port so that it does not have I/O bridge
window.
Now when the ACPI Notify() is triggered ACPI hotplug handler calls
acpiphp_native_scan_bridge() for each non-hotplug bridge (as this system is
using native PCIe hotplug) and pci_assign_unassigned_bridge_resources() to
allocate resources.
The device connected to the root port is a PCIe switch (Thunderbolt
controller) with two hotplug downstream ports. Because of the hotplug ports
__pci_bus_size_bridges() tries to add "additional I/O" of 256 bytes to each
(DEFAULT_HOTPLUG_IO_SIZE). This gets further aligned to 4k as that's the
minimum I/O window size so each hotplug port gets 4k I/O window and the
same happens for the root port (which is also hotplug port). This means
3 * 4k = 12k I/O window.
Because of this pci_assign_unassigned_bridge_resources() ends up opening a
I/O bridge window for the root port at first available I/O address which
seems to be in range 0x1000 - 0x3fff. Normally this range is used for ACPI
stuff such as GPE bits (below is part of /proc/ioports):
1800-1803 : ACPI PM1a_EVT_BLK
1804-1805 : ACPI PM1a_CNT_BLK
1808-180b : ACPI PM_TMR
1810-1815 : ACPI CPU throttle
1850-1850 : ACPI PM2_CNT_BLK
1854-1857 : pnp 00:05
1860-187f : ACPI GPE0_BLK
However, when the ACPI Notify() happened this range was not yet reserved
for ACPI/PNP (that happens later) so PCI gets it. It then starts writing to
this range and accidentally stomps over GPE bits among other things causing
the endless stream of messages about missing GPE handler.
This problem does not happen if "pci=hpiosize=0" is passed in the kernel
command line. The reason is that then the kernel does not try to allocate
the additional 256 bytes for each hotplug port.
Fix this by allocating resources directly below the non-hotplug bridges
where a new device may appear as a result of ACPI Notify(). This avoids the
hotplug bridges and prevents opening the additional I/O window.
Fixes: 84c8b58ed3 ("ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203617
Link: https://lore.kernel.org/r/20191030150545.19885-1-mika.westerberg@linux.intel.com
Reported-by: Valerio Passini <passini.valerio@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org
The newer ibm,drc-info property is a condensed description of the old
ibm,drc-* properties (ie. names, types, indexes, and power-domains).
When matching a drc-index to a drc-name we need to verify that the
index is within the start and last drc-index range and map it to a
drc-name using the drc-name-prefix and logical index.
Fix the mapping by checking that the index is within the range of the
current drc-info entry, and build the name from the drc-name-prefix
concatenated with the starting drc-name-suffix value and the sequential
index obtained by subtracting ibm,my-drc-index from this entries
drc-start-index.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-10-git-send-email-tyreld@linux.ibm.com
The device tree is in big endian format and any properties directly
retrieved using OF helpers that don't explicitly byte swap should
be annotated. In particular there are several places where we grab
the opaque property value for the old ibm,drc-* properties and the
ibm,my-drc-index property.
Fix this for better static checking by annotating values we know to
explicitly big endian, and byte swap where appropriate.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-9-git-send-email-tyreld@linux.ibm.com
Split physical PCI slot registration scanning into separate routines
that support the old ibm,drc-* properties and one that supports the
new compressed ibm,drc-info property.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-7-git-send-email-tyreld@linux.ibm.com
In the event that the partition is migrated to a platform with older
firmware that doesn't support the ibm,drc-info property the device
tree is modified to remove the ibm,drc-info property and replace it
with the older style ibm,drc-* properties for types, names, indexes,
and power-domains. One of the requirements of the drc-info firmware
feature is that the client is able to handle both the new property,
and old style properties at runtime. Therefore we can't rely on the
firmware feature alone to dictate which property is currently
present in the device tree.
Fix this short coming by checking explicitly for the ibm,drc-info
property, and falling back to the older ibm,drc-* properties if it
doesn't exist.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-6-git-send-email-tyreld@linux.ibm.com
The first entry of the ibm,drc-info property is an int encoded count
of the number of drc-info entries that follow. The "value" pointer
returned by of_prop_next_u32() is still pointing at the this value
when we call of_read_drc_info_cell(), but the helper function
expects that value to be pointing at the first element of an entry.
Fix up by incrementing the "value" pointer to point at the first
element of the first drc-info entry prior.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-5-git-send-email-tyreld@linux.ibm.com
This addresses deadlocks in these common cases in hierarchies containing
two switches:
- All involved ports are runtime suspended and they are unplugged. This
can happen easily if the drivers involved automatically enable runtime
PM (xHCI for example does that).
- System is suspended (e.g., closing the lid on a laptop) with a dock +
something else connected, and the dock is unplugged while suspended.
These cases lead to the following deadlock:
INFO: task irq/126-pciehp:198 blocked for more than 120 seconds.
irq/126-pciehp D 0 198 2 0x80000000
Call Trace:
schedule+0x2c/0x80
schedule_timeout+0x246/0x350
wait_for_completion+0xb7/0x140
kthread_stop+0x49/0x110
free_irq+0x32/0x70
pcie_shutdown_notification+0x2f/0x50
pciehp_remove+0x27/0x50
pcie_port_remove_service+0x36/0x50
device_release_driver+0x12/0x20
bus_remove_device+0xec/0x160
device_del+0x13b/0x350
device_unregister+0x1a/0x60
remove_iter+0x1e/0x30
device_for_each_child+0x56/0x90
pcie_port_device_remove+0x22/0x40
pcie_portdrv_remove+0x20/0x60
pci_device_remove+0x3e/0xc0
device_release_driver_internal+0x18c/0x250
device_release_driver+0x12/0x20
pci_stop_bus_device+0x6f/0x90
pci_stop_bus_device+0x31/0x90
pci_stop_and_remove_bus_device+0x12/0x20
pciehp_unconfigure_device+0x88/0x140
pciehp_disable_slot+0x6a/0x110
pciehp_handle_presence_or_link_change+0x263/0x400
pciehp_ist+0x1c9/0x1d0
irq_thread_fn+0x24/0x60
irq_thread+0xeb/0x190
kthread+0x120/0x140
INFO: task irq/190-pciehp:2288 blocked for more than 120 seconds.
irq/190-pciehp D 0 2288 2 0x80000000
Call Trace:
__schedule+0x2a2/0x880
schedule+0x2c/0x80
schedule_preempt_disabled+0xe/0x10
mutex_lock+0x2c/0x30
pci_lock_rescan_remove+0x15/0x20
pciehp_unconfigure_device+0x4d/0x140
pciehp_disable_slot+0x6a/0x110
pciehp_handle_presence_or_link_change+0x263/0x400
pciehp_ist+0x1c9/0x1d0
irq_thread_fn+0x24/0x60
irq_thread+0xeb/0x190
kthread+0x120/0x140
What happens here is that the whole hierarchy is runtime resumed and the
parent PCIe downstream port, which got the hot-remove event, starts
removing devices below it, taking pci_lock_rescan_remove() lock. When the
child PCIe port is runtime resumed it calls pciehp_check_presence() which
ends up calling pciehp_card_present() and pciehp_check_link_active(). Both
of these use pcie_capability_read_word(), which notices that the underlying
device is already gone and returns PCIBIOS_DEVICE_NOT_FOUND with the
capability value set to 0. When pciehp gets this value it thinks that its
child device is also hot-removed and schedules its IRQ thread to handle the
event.
The deadlock happens when the child's IRQ thread runs and tries to acquire
pci_lock_rescan_remove() which is already taken by the parent and the
parent waits for the child's IRQ thread to finish.
Prevent this from happening by checking the return value of
pcie_capability_read_word() and if it is PCIBIOS_DEVICE_NOT_FOUND stop
performing any hot-removal activities.
[bhelgaas: add common scenarios to commit log]
Link: https://lore.kernel.org/r/20191029170022.57528-2-mika.westerberg@linux.intel.com
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We try to keep PCIe hotplug ports runtime suspended when entering system
suspend. Because the PCIe portdrv sets the DPM_FLAG_NEVER_SKIP flag, the PM
core always calls system suspend/resume hooks even if the device is left
runtime suspended. Since PCIe hotplug driver re-used the same function for
both runtime suspend and system suspend, it ended up disabling hotplug
interrupt twice and the second time following was printed:
pciehp 0000:03:01.0:pcie204: pcie_do_write_cmd: no response from device
Prevent this from happening by checking whether the device is already
runtime suspended when the system suspend hook is called.
Fixes: 9c62f0bfb8 ("PCI: pciehp: Implement runtime PM callbacks")
Link: https://lore.kernel.org/r/20191029170022.57528-1-mika.westerberg@linux.intel.com
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Infinite timeout loops are hard to read. Refactor it to plausible 'do {}
while ()'.
Note, the supplied timeout can't be negative for current use, though if
it's not dividable to 10, we may go below 0, that's why type of the
parameter is int. And thus, we may move the check to the loop condition.
No functional change intended.
Link: https://lore.kernel.org/r/20191108111855.85866-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
A sysfs request to enable or disable a PCIe hotplug slot should not
return before it has been carried out. That is sought to be achieved by
waiting until the controller's "pending_events" have been cleared.
However the IRQ thread pciehp_ist() clears the "pending_events" before
it acts on them. If pciehp_sysfs_enable_slot() / _disable_slot() happen
to check the "pending_events" after they have been cleared but while
pciehp_ist() is still running, the functions may return prematurely
with an incorrect return value.
Fix by introducing an "ist_running" flag which must be false before a sysfs
request is allowed to return.
Fixes: 32a8cef274 ("PCI: pciehp: Enable/disable exclusively from IRQ thread")
Link: https://lore.kernel.org/linux-pci/1562226638-54134-1-git-send-email-wangxiongfeng2@huawei.com
Link: https://lore.kernel.org/r/4174210466e27eb7e2243dd1d801d5f75baaffd8.1565345211.git.lukas@wunner.de
Reported-and-tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
- Cleanup pciehp LED/indicator control with a new consolidated
pciehp_set_indicators() interface that controls both Attention and
Power Indicators (Denis Efremov)
* pci/pciehp:
PCI: pciehp: Refer to "Indicators" instead of "LEDs" in comments
PCI: pciehp: Remove pciehp_green_led_{on,off,blink}()
PCI: pciehp: Remove pciehp_set_attention_status()
PCI: pciehp: Combine adjacent indicator updates
PCI: pciehp: Add pciehp_set_indicators() to set both indicators
- Initial support for running on a system with an Ultravisor, which is software
that runs below the hypervisor and protects guests against some attacks by
the hypervisor.
- Support for building the kernel to run as a "Secure Virtual Machine", ie. as
a guest capable of running on a system with an Ultravisor.
- Some changes to our DMA code on bare metal, to allow devices with medium
sized DMA masks (> 32 && < 59 bits) to use more than 2GB of DMA space.
- Support for firmware assisted crash dumps on bare metal (powernv).
- Two series fixing bugs in and refactoring our PCI EEH code.
- A large series refactoring our exception entry code to use gas macros, both
to make it more readable and also enable some future optimisations.
As well as many cleanups and other minor features & fixups.
Thanks to:
Adam Zerella, Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan, Aneesh
Kumar K.V, Anju T Sudhakar, Anshuman Khandual, Balbir Singh, Benjamin
Herrenschmidt, Cédric Le Goater, Christophe JAILLET, Christophe Leroy,
Christopher M. Riedl, Christoph Hellwig, Claudio Carvalho, Daniel Axtens,
David Gibson, David Hildenbrand, Desnes A. Nunes do Rosario, Ganesh Goudar,
Gautham R. Shenoy, Greg Kurz, Guerney Hunt, Gustavo Romero, Halil Pasic, Hari
Bathini, Joakim Tjernlund, Jonathan Neuschafer, Jordan Niethe, Leonardo Bras,
Lianbo Jiang, Madhavan Srinivasan, Mahesh Salgaonkar, Mahesh Salgaonkar,
Masahiro Yamada, Maxiwell S. Garcia, Michael Anderson, Nathan Chancellor,
Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran, Qian Cai, Ram
Pai, Ravi Bangoria, Reza Arbab, Ryan Grimm, Sam Bobroff, Santosh Sivaraj,
Segher Boessenkool, Sukadev Bhattiprolu, Thiago Bauermann, Thiago Jung
Bauermann, Thomas Gleixner, Tom Lendacky, Vasant Hegde.
-----BEGIN PGP SIGNATURE-----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=WlW+
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"This is a bit late, partly due to me travelling, and partly due to a
power outage knocking out some of my test systems *while* I was
travelling.
- Initial support for running on a system with an Ultravisor, which
is software that runs below the hypervisor and protects guests
against some attacks by the hypervisor.
- Support for building the kernel to run as a "Secure Virtual
Machine", ie. as a guest capable of running on a system with an
Ultravisor.
- Some changes to our DMA code on bare metal, to allow devices with
medium sized DMA masks (> 32 && < 59 bits) to use more than 2GB of
DMA space.
- Support for firmware assisted crash dumps on bare metal (powernv).
- Two series fixing bugs in and refactoring our PCI EEH code.
- A large series refactoring our exception entry code to use gas
macros, both to make it more readable and also enable some future
optimisations.
As well as many cleanups and other minor features & fixups.
Thanks to: Adam Zerella, Alexey Kardashevskiy, Alistair Popple, Andrew
Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman Khandual,
Balbir Singh, Benjamin Herrenschmidt, Cédric Le Goater, Christophe
JAILLET, Christophe Leroy, Christopher M. Riedl, Christoph Hellwig,
Claudio Carvalho, Daniel Axtens, David Gibson, David Hildenbrand,
Desnes A. Nunes do Rosario, Ganesh Goudar, Gautham R. Shenoy, Greg
Kurz, Guerney Hunt, Gustavo Romero, Halil Pasic, Hari Bathini, Joakim
Tjernlund, Jonathan Neuschafer, Jordan Niethe, Leonardo Bras, Lianbo
Jiang, Madhavan Srinivasan, Mahesh Salgaonkar, Mahesh Salgaonkar,
Masahiro Yamada, Maxiwell S. Garcia, Michael Anderson, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Oliver
O'Halloran, Qian Cai, Ram Pai, Ravi Bangoria, Reza Arbab, Ryan Grimm,
Sam Bobroff, Santosh Sivaraj, Segher Boessenkool, Sukadev Bhattiprolu,
Thiago Bauermann, Thiago Jung Bauermann, Thomas Gleixner, Tom
Lendacky, Vasant Hegde"
* tag 'powerpc-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (264 commits)
powerpc/mm/mce: Keep irqs disabled during lockless page table walk
powerpc: Use ftrace_graph_ret_addr() when unwinding
powerpc/ftrace: Enable HAVE_FUNCTION_GRAPH_RET_ADDR_PTR
ftrace: Look up the address of return_to_handler() using helpers
powerpc: dump kernel log before carrying out fadump or kdump
docs: powerpc: Add missing documentation reference
powerpc/xmon: Fix output of XIVE IPI
powerpc/xmon: Improve output of XIVE interrupts
powerpc/mm/radix: remove useless kernel messages
powerpc/fadump: support holes in kernel boot memory area
powerpc/fadump: remove RMA_START and RMA_END macros
powerpc/fadump: update documentation about option to release opalcore
powerpc/fadump: consider f/w load area
powerpc/opalcore: provide an option to invalidate /sys/firmware/opal/core file
powerpc/opalcore: export /sys/firmware/opal/core for analysing opal crashes
powerpc/fadump: update documentation about CONFIG_PRESERVE_FA_DUMP
powerpc/fadump: add support to preserve crash data on FADUMP disabled kernel
powerpc/fadump: improve how crashed kernel's memory is reserved
powerpc/fadump: consider reserved ranges while releasing memory
powerpc/fadump: make crash memory ranges array allocation generic
...
The PCIe spec doesn't mention "green LEDs" or "amber LEDs". Replace those
terms with "Power Indicator" and "Attention Indicator" so the comments
match the spec language. Comment changes only.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove pciehp_green_led_{on,off,blink}() and use pciehp_set_indicators()
instead, since the code is mostly the same.
[bhelgaas: drop set_power_indicator() wrapper to reduce the number of
interfaces]
Link: https://lore.kernel.org/r/20190903111021.1559-5-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Remove pciehp_set_attention_status() and use pciehp_set_indicators()
instead, since the code is mostly the same.
Link: https://lore.kernel.org/r/20190903111021.1559-4-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Combine adjacent updates of power and attention indicators into a single
pciehp_set_indicators() call. This sends one command to the hotplug
controller instead of two.
Link: https://lore.kernel.org/r/20190903111021.1559-3-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Add pciehp_set_indicators() to set power and attention indicators with a
single register write.
This is a minor optimization because we frequently set both indicators and
this can do it with a single command. It also reduces the number of
interfaces related to the indicators and makes them more discoverable
because callers use the PCI_EXP_SLTCTL_ATTN_IND_* and
PCI_EXP_SLTCTL_PWR_IND_* definitions directly.
[bhelgaas: extend commit log, s/PCI_EXP_SLTCTL_.*_IND_NONE/INDICATOR_NOOP/
so they don't look like things defined by the spec, add function doc, mask
commands to make it obvious we only send valid commands
(pcie_do_write_cmd() does mask it, but requires more effort to verify)]
Link: https://lore.kernel.org/r/20190903111021.1559-2-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pnv_php is generally used with PCIe bridges which provide a native
interface for setting the attention and power indicator LEDs. Wire up
those interfaces even if firmware does not have support for them (yet...)
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-11-oohall@gmail.com
Currently we check that an IODA2 compatible PHB is upstream of this slot.
This is mainly to avoid pnv_php creating slots for the various "virtual
PHBs" that we create for NVLink. There's no real need for this restriction
so allow it on IODA3.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-10-oohall@gmail.com
When performing EEH recovery of devices in a hotplug slot we need to use
the slot driver's ->reset_slot() callback to prevent spurious hotplug
events due to spurious DLActive and PresDet change interrupts. Add a
reset_slot() callback to pnv_php so we can handle recovery of devices
in pnv_php managed slots.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-9-oohall@gmail.com
The SGI SN2 support is about to be removed. Remove this driver that
depends on the SN2 support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-6-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
Mark switch cases where we are expecting to fall through.
This fixes the following warning (Building: allmodconfig i386):
drivers/pci/hotplug/ibmphp_res.c: In function ‘update_bridge_ranges’:
drivers/pci/hotplug/ibmphp_res.c:1943:16: warning: this statement may fall through [-Wimplicit-fallthrough=]
function = 0x8;
~~~~~~~~~^~~~~
drivers/pci/hotplug/ibmphp_res.c:1944:6: note: here
case PCI_HEADER_TYPE_MULTIBRIDGE:
^~~~
Link: https://lore.kernel.org/r/20190802012248.GA22622@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
When building with -Wsometimes-uninitialized, clang warns:
drivers/pci/hotplug/rpaphp_core.c:243:14: warning: variable 'fndit' is
used uninitialized whenever 'for' loop exits because its condition is
false [-Wsometimes-uninitialized]
for (j = 0; j < entries; j++) {
^~~~~~~~~~~
drivers/pci/hotplug/rpaphp_core.c:256:6: note: uninitialized use occurs
here
if (fndit)
^~~~~
drivers/pci/hotplug/rpaphp_core.c:243:14: note: remove the condition if
it is always true
for (j = 0; j < entries; j++) {
^~~~~~~~~~~
drivers/pci/hotplug/rpaphp_core.c:233:14: note: initialize the variable
'fndit' to silence this warning
int j, fndit;
^
= 0
fndit is only used to gate a sprintf call, which can be moved into the
loop to simplify the code and eliminate the local variable, which will
fix this warning.
Fixes: 2fcf3ae508 ("hotplug/drc-info: Add code to search ibm,drc-info property")
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Joel Savitz <jsavitz@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://github.com/ClangBuiltLinux/linux/issues/504
Link: https://lore.kernel.org/r/20190603221157.58502-1-natechancellor@gmail.com
MY_NAME is only used once and offers no benefit, so remove it.
Link: https://lore.kernel.org/lkml/20190509141456.223614-11-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
PCIE_MODULE_NAME is only used once and offers no benefit, so remove it.
Link: https://lore.kernel.org/lkml/20190509141456.223614-10-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Replace the last uses of dbg() with the equivalent pr_debug(), then remove
unused dbg(), err(), info(), and warn() wrappers.
Link: https://lore.kernel.org/lkml/20190509141456.223614-9-helgaas@kernel.org
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Log messages with pci_dev, not pcie_device. Factor out common message
prefixes with dev_fmt().
Example output change:
- pciehp 0000:00:06.0:pcie004: Slot(0) Powering on due to button press
+ pcieport 0000:00:06.0: pciehp: Slot(0) Powering on due to button press
Link: https://lore.kernel.org/lkml/20190509141456.223614-8-helgaas@kernel.org
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Previously pciehp debug messages were enabled by the pciehp_debug module
parameter, e.g., by booting with this kernel command line option:
pciehp.pciehp_debug=1
Convert this mechanism to use the generic dynamic debug (dyndbg) feature.
After this commit, pciehp debug messages are enabled by building the kernel
with CONFIG_DYNAMIC_DEBUG=y and booting with this command line option:
dyndbg="file pciehp* +p"
The dyndbg facility is much more flexible: messages can be enabled at boot-
or run-time based on the file name, function name, line number, message
test, etc. See Documentation/admin-guide/dynamic-debug-howto.rst for more
details.
Link: https://lore.kernel.org/lkml/20190509141456.223614-7-helgaas@kernel.org
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
[bhelgaas: commit log, comment, remove pciehp_debug parameter]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
We're about to convert pciehp to the dyndbg mechanism, which means we can
eventually remove pciehp_debug.
Replace uses of pciehp_debug with dbg() and ctrl_dbg(), which check
pciehp_debug internally.
Link: https://lore.kernel.org/lkml/20190509141456.223614-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
When allocating the slot structure we store a pointer to the associated
device_node. We really should be incrementing the reference count, so add
an of_node_get() during slot alloc and an of_node_put() during slot
dealloc.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The find_dlpar_node() helper returns a device node with its reference
incremented. Both the add and remove paths use this helper for find the
appropriate node, but fail to release the reference when done.
Annotate the find_dlpar_node() helper with a comment about the incremented
reference count and call of_node_put() on the obtained device_node in the
add and remove paths. Also, fixup a reference leak in the find_vio_slot()
helper where we fail to call of_node_put() on the vdevice node after we
iterate over its children.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
During a safe hot remove, the OS powers off the slot, which may cause a
Data Link Layer State Changed event. The slot has already been set to
OFF_STATE, so that event results in re-enabling the device, making it
impossible to safely remove it.
Clear out the Presence Detect Changed and Data Link Layer State Changed
events when the disabled slot has settled down.
It is still possible to re-enable the device if it remains in the slot
after pressing the Attention Button by pressing it again.
Fixes the problem that Micah reported below: an NVMe drive power button may
not actually turn off the drive.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203237
Reported-by: Micah Parrish <micah.parrish@hpe.com>
Tested-by: Micah Parrish <micah.parrish@hpe.com>
Signed-off-by: Sergey Miroshnichenko <s.miroshnichenko@yadro.com>
[bhelgaas: changelog, add bugzilla URL]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.19+
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
* pci/pm:
PCI/PME: Fix possible use-after-free on remove
PCI/PME: Fix hotplug/sysfs remove deadlock in pcie_pme_remove()
PCI: pciehp: Disable Data Link Layer State Changed event on suspend
Revert "PCI/PME: Implement runtime PM callbacks"
PCI: Blacklist power management of Gigabyte X299 DESIGNARE EX PCIe ports
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
* pci/misc:
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI: Clean up usage of __u32 type
genirq/msi: Clean up usage of __u8/__u16 types
PCI: Move Rohm Vendor ID to generic list
PCI: pciehp: Add HXT quirk for Command Completed errata
PCI: Add ACS quirk for HXT SD4800
PCI: Add HXT vendor ID
PCI: Use of_node_name_eq() for node name comparisons
PCI: Mark expected switch fall-through
Commit 0e157e5286 ("PCI/PME: Implement runtime PM callbacks") tried to
solve an issue where the hierarchy immediately wakes up when it is
transitioned into D3cold. However, it turns out to prevent PME
propagation on some systems that do not support D3cold.
I looked more closely at what might cause the immediate wakeup. It happens
when the ACPI power resource of the root port is turned off. The AML code
associated with the _OFF() method of the ACPI power resource starts a PCIe
L2/L3 Ready transition and waits for it to complete. Right after the L2/L3
Ready transition is started the root port receives a PME from the
downstream port.
The simplest hierarchy where this happens looks like this:
00:1d.0 PCIe Root Port
^
|
v
05:00.0 PCIe switch #1 upstream port
06:01.0 PCIe switch #1 downstream hotplug port
^
|
v
08:00.0 PCIe switch #2 upstream port
It seems that the PCIe link between the two switches, before
PME_Turn_Off/PME_TO_Ack is complete for the whole hierarchy, goes
inactive and triggers PME towards the root port bringing it back to D0.
The L2/L3 Ready sequence is described in PCIe r4.0 spec sections 5.2 and
5.3.3 but unfortunately they do not state what happens if DLLSCE is
enabled during the sequence.
Disabling Data Link Layer State Changed event (DLLSCE) seems to prevent
the issue and still allows the downstream hotplug port to notice when a
device is plugged/unplugged.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202593
Fixes: 0e157e5286 ("PCI/PME: Implement runtime PM callbacks")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v4.20+
The HXT SD4800 PCI controller does not set the Command Completed bit unless
writes to the Slot Command register change "Control" bits.
Add SD4800 to the quirk.
Signed-off-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Joey Zheng <yu.zheng@hxt-semitech.com>
The sem_exit variable is conceptually a completion, so it should be called
that.
Similarly, the semOperations semaphore is a simple mutex, and can be
changed into that, respectively.
With both converted, the ibmphp_hpc_initvars() function is no longer used
and can be removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Shameerali reported that running v4.20-rc1 as QEMU guest, the PCIe hotplug
port times out during boot:
pciehp 0000:00:01.0:pcie004: Timeout on hotplug command 0x03f1 (issued 1016 msec ago)
pciehp 0000:00:01.0:pcie004: Timeout on hotplug command 0x03f1 (issued 1024 msec ago)
pciehp 0000:00:01.0:pcie004: Failed to check link status
pciehp 0000:00:01.0:pcie004: Timeout on hotplug command 0x02f1 (issued 2520 msec ago)
The issue was bisected down to commit 720d6a671a ("PCI: pciehp: Do not
handle events if interrupts are masked") and was further analyzed by the
reporter to be caused by the fact that pciehp first updates the hardware
and only then cache the ctrl->slot_ctrl in pcie_do_write_cmd(). If the
interrupt happens before we cache the value, pciehp_isr() reads value 0 and
decides that the interrupt was not meant for it causing the above timeout
to trigger.
Fix by moving ctrl->slot_ctrl assignment to happen before it is written to
the hardware.
Fixes: 720d6a671a ("PCI: pciehp: Do not handle events if interrupts are masked")
Link: https://lore.kernel.org/linux-pci/5FC3163CFD30C246ABAA99954A238FA8387DD344@FRAEML521-MBX.china.huawei.com
Reported-by: Shameerali Kolothum Thodi <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull XArray conversion from Matthew Wilcox:
"The XArray provides an improved interface to the radix tree data
structure, providing locking as part of the API, specifying GFP flags
at allocation time, eliminating preloading, less re-walking the tree,
more efficient iterations and not exposing RCU-protected pointers to
its users.
This patch set
1. Introduces the XArray implementation
2. Converts the pagecache to use it
3. Converts memremap to use it
The page cache is the most complex and important user of the radix
tree, so converting it was most important. Converting the memremap
code removes the only other user of the multiorder code, which allows
us to remove the radix tree code that supported it.
I have 40+ followup patches to convert many other users of the radix
tree over to the XArray, but I'd like to get this part in first. The
other conversions haven't been in linux-next and aren't suitable for
applying yet, but you can see them in the xarray-conv branch if you're
interested"
* 'xarray' of git://git.infradead.org/users/willy/linux-dax: (90 commits)
radix tree: Remove multiorder support
radix tree test: Convert multiorder tests to XArray
radix tree tests: Convert item_delete_rcu to XArray
radix tree tests: Convert item_kill_tree to XArray
radix tree tests: Move item_insert_order
radix tree test suite: Remove multiorder benchmarking
radix tree test suite: Remove __item_insert
memremap: Convert to XArray
xarray: Add range store functionality
xarray: Move multiorder_check to in-kernel tests
xarray: Move multiorder_shrink to kernel tests
xarray: Move multiorder account test in-kernel
radix tree test suite: Convert iteration test to XArray
radix tree test suite: Convert tag_tagged_items to XArray
radix tree: Remove radix_tree_clear_tags
radix tree: Remove radix_tree_maybe_preload_order
radix tree: Remove split/join code
radix tree: Remove radix_tree_update_node_t
page cache: Finish XArray conversion
dax: Convert page fault handlers to XArray
...
Notable changes:
- A large series to rewrite our SLB miss handling, replacing a lot of fairly
complicated asm with much fewer lines of C.
- Following on from that, we now maintain a cache of SLB entries for each
process and preload them on context switch. Leading to a 27% speedup for our
context switch benchmark on Power9.
- Improvements to our handling of SLB multi-hit errors. We now print more debug
information when they occur, and try to continue running by flushing the SLB
and reloading, rather than treating them as fatal.
- Enable THP migration on 64-bit Book3S machines (eg. Power7/8/9).
- Add support for physical memory up to 2PB in the linear mapping on 64-bit
Book3S. We only support up to 512TB as regular system memory, otherwise the
percpu allocator runs out of vmalloc space.
- Add stack protector support for 32 and 64-bit, with a per-task canary.
- Add support for PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP.
- Support recognising "big cores" on Power9, where two SMT4 cores are presented
to us as a single SMT8 core.
- A large series to cleanup some of our ioremap handling and PTE flags.
- Add a driver for the PAPR SCM (storage class memory) interface, allowing
guests to operate on SCM devices (acked by Dan).
- Changes to our ftrace code to handle very large kernels, where we need to use
a trampoline to get to ftrace_caller().
Many other smaller enhancements and cleanups.
Thanks to:
Alan Modra, Alistair Popple, Aneesh Kumar K.V, Anton Blanchard, Aravinda
Prasad, Bartlomiej Zolnierkiewicz, Benjamin Herrenschmidt, Breno Leitao,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Dan Carpenter, Daniel
Axtens, Finn Thain, Gautham R. Shenoy, Gustavo Romero, Haren Myneni, Hari
Bathini, Jia Hongtao, Joel Stanley, John Allen, Laurent Dufour, Madhavan
Srinivasan, Mahesh Salgaonkar, Mark Hairgrove, Masahiro Yamada, Michael
Bringmann, Michael Neuling, Michal Suchanek, Murilo Opsfelder Araujo, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers, Oliver O'Halloran,
Paul Mackerras, Petr Vorel, Rashmica Gupta, Reza Arbab, Rob Herring, Sam
Bobroff, Samuel Mendoza-Jonas, Scott Wood, Stan Johnson, Stephen Rothwell,
Stewart Smith, Suraj Jitindar Singh, Tyrel Datwyler, Vaibhav Jain, Vasant
Hegde, YueHaibing, zhong jiang,
-----BEGIN PGP SIGNATURE-----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=I0pj
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A large series to rewrite our SLB miss handling, replacing a lot of
fairly complicated asm with much fewer lines of C.
- Following on from that, we now maintain a cache of SLB entries for
each process and preload them on context switch. Leading to a 27%
speedup for our context switch benchmark on Power9.
- Improvements to our handling of SLB multi-hit errors. We now print
more debug information when they occur, and try to continue running
by flushing the SLB and reloading, rather than treating them as
fatal.
- Enable THP migration on 64-bit Book3S machines (eg. Power7/8/9).
- Add support for physical memory up to 2PB in the linear mapping on
64-bit Book3S. We only support up to 512TB as regular system
memory, otherwise the percpu allocator runs out of vmalloc space.
- Add stack protector support for 32 and 64-bit, with a per-task
canary.
- Add support for PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP.
- Support recognising "big cores" on Power9, where two SMT4 cores are
presented to us as a single SMT8 core.
- A large series to cleanup some of our ioremap handling and PTE
flags.
- Add a driver for the PAPR SCM (storage class memory) interface,
allowing guests to operate on SCM devices (acked by Dan).
- Changes to our ftrace code to handle very large kernels, where we
need to use a trampoline to get to ftrace_caller().
And many other smaller enhancements and cleanups.
Thanks to: Alan Modra, Alistair Popple, Aneesh Kumar K.V, Anton
Blanchard, Aravinda Prasad, Bartlomiej Zolnierkiewicz, Benjamin
Herrenschmidt, Breno Leitao, Cédric Le Goater, Christophe Leroy,
Christophe Lombard, Dan Carpenter, Daniel Axtens, Finn Thain, Gautham
R. Shenoy, Gustavo Romero, Haren Myneni, Hari Bathini, Jia Hongtao,
Joel Stanley, John Allen, Laurent Dufour, Madhavan Srinivasan, Mahesh
Salgaonkar, Mark Hairgrove, Masahiro Yamada, Michael Bringmann,
Michael Neuling, Michal Suchanek, Murilo Opsfelder Araujo, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers, Oliver
O'Halloran, Paul Mackerras, Petr Vorel, Rashmica Gupta, Reza Arbab,
Rob Herring, Sam Bobroff, Samuel Mendoza-Jonas, Scott Wood, Stan
Johnson, Stephen Rothwell, Stewart Smith, Suraj Jitindar Singh, Tyrel
Datwyler, Vaibhav Jain, Vasant Hegde, YueHaibing, zhong jiang"
* tag 'powerpc-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (221 commits)
Revert "selftests/powerpc: Fix out-of-tree build errors"
powerpc/msi: Fix compile error on mpc83xx
powerpc: Fix stack protector crashes on CPU hotplug
powerpc/traps: restore recoverability of machine_check interrupts
powerpc/64/module: REL32 relocation range check
powerpc/64s/radix: Fix radix__flush_tlb_collapsed_pmd double flushing pmd
selftests/powerpc: Add a test of wild bctr
powerpc/mm: Fix page table dump to work on Radix
powerpc/mm/radix: Display if mappings are exec or not
powerpc/mm/radix: Simplify split mapping logic
powerpc/mm/radix: Remove the retry in the split mapping logic
powerpc/mm/radix: Fix small page at boundary when splitting
powerpc/mm/radix: Fix overuse of small pages in splitting logic
powerpc/mm/radix: Fix off-by-one in split mapping logic
powerpc/ftrace: Handle large kernel configs
powerpc/mm: Fix WARN_ON with THP NUMA migration
selftests/powerpc: Fix out-of-tree build errors
powerpc/time: no steal_time when CONFIG_PPC_SPLPAR is not selected
powerpc/time: Only set CONFIG_ARCH_HAS_SCALED_CPUTIME on PPC64
powerpc/time: isolate scaled cputime accounting in dedicated functions.
...
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
Currently, eeh_pe_state_mark() marks a PE (and it's children) with a
state and then performs additional processing if that state included
EEH_PE_ISOLATED.
The state parameter is always a constant at the call site, so
rearrange eeh_pe_state_mark() into two functions and just call the
appropriate one at each site.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use kmemdup() rather than duplicating its implementation.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/pci/hotplug/cpqphp_core.c: In function 'init_SERR':
drivers/pci/hotplug/cpqphp_core.c:124:5: warning: variable 'physical_slot' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Basically we need to do the same thing when runtime suspending than with
system sleep so re-use those operations here. This makes sure hotplug
interrupt does not trigger immediately when the link goes down.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PCIe native hotplug shares MSI vector with native PME so the interrupt
handler might get called even the hotplug interrupt is masked. In that case
we should not handle any events because the interrupt was not meant for us.
Modify the PCIe hotplug interrupt handler to check this accordingly and
bail out if it finds out that the interrupt was not about hotplug.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
When PCIe hotplug port is transitioned into D3hot, the link to the
downstream component will go down. If hotplug interrupt generation is
enabled when that happens, it will trigger immediately, waking up the
system and bringing the link back up.
To prevent this, disable hotplug interrupt generation when system suspend
is entered. This does not prevent wakeup from low power states according
to PCIe 4.0 spec section 6.7.3.4:
Software enables a hot-plug event to generate a wakeup event by
enabling software notification of the event as described in Section
6.7.3.1. Note that in order for software to disable interrupt generation
while keeping wakeup generation enabled, the Hot-Plug Interrupt Enable
bit must be cleared.
So as long as we have set the slot event mask accordingly, wakeup should
work even if slot interrupt is disabled. The port should trigger wake and
then send PME to the root port when the PCIe hierarchy is brought back up.
Limit this to systems using native PME mechanism to make sure older Apple
systems depending on commit e3354628c376 ("PCI: pciehp: Support interrupts
sent from D3hot") still continue working.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The spec has timing requirements when waiting for a link to become active
after a conventional reset. Implement those hard delays when waiting for
an active link so pciehp and dpc drivers don't need to duplicate this.
For devices that don't support data link layer active reporting, wait the
fixed time recommended by the PCIe spec.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
