Core & protocols
----------------
- Wrap datapath globals into net_aligned_data, to avoid false sharing.
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container).
- Add SO_INQ and SCM_INQ support to AF_UNIX.
- Add SIOCINQ support to AF_VSOCK.
- Add TCP_MAXSEG sockopt to MPTCP.
- Add IPv6 force_forwarding sysctl to enable forwarding per interface.
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB.
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users.
- Convert TCP send queue handling from tasklet to BH workque.
- Improve BPF iteration over TCP sockets to see each socket exactly once.
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code.
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel NAPI
thread when threaded NAPI gets disabled. Previously thread would stick
around until ifdown due to tricky synchronization.
- Allow multicast routing to take effect on locally-generated packets.
- Add output interface argument for End.X in segment routing.
- MCTP: add support for gateway routing, improve bind() handling.
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink.
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed.
- Support NUD_PERMANENT for proxy neighbor entries.
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM.
- Add sequence numbers to netconsole messages. Unregister netconsole's
console when all net targets are removed. Code refactoring.
Add a number of selftests.
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup.
- Support inspecting ref_tracker state via DebugFS.
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links.
- Allow providing upcall pid for the 'execute' command in openvswitch.
- Remove DCCP support from Netfilter's conntrack.
- Disallow multiple packet duplications in the queuing layer.
- Prevent use of deprecated iptables code on PREEMPT_RT.
Driver API
----------
- Support RSS and hashing configuration over ethtool Netlink.
- Add dedicated ethtool callbacks for getting and setting hashing fields.
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc.
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs.
- Support traffic classes in devlink rate API for bandwidth management.
- Remove rtnl_lock dependency from UDP tunnel port configuration.
Device drivers
--------------
- Add a new Broadcom driver for 800G Ethernet (bnge).
- Add a standalone driver for Microchip ZL3073x DPLL.
- Remove IBM's NETIUCV device driver.
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is used
by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=lqbe
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Wrap datapath globals into net_aligned_data, to avoid false sharing
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container)
- Add SO_INQ and SCM_INQ support to AF_UNIX
- Add SIOCINQ support to AF_VSOCK
- Add TCP_MAXSEG sockopt to MPTCP
- Add IPv6 force_forwarding sysctl to enable forwarding per interface
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users
- Convert TCP send queue handling from tasklet to BH workque
- Improve BPF iteration over TCP sockets to see each socket exactly
once
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel
NAPI thread when threaded NAPI gets disabled. Previously thread
would stick around until ifdown due to tricky synchronization
- Allow multicast routing to take effect on locally-generated packets
- Add output interface argument for End.X in segment routing
- MCTP: add support for gateway routing, improve bind() handling
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed
- Support NUD_PERMANENT for proxy neighbor entries
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM
- Add sequence numbers to netconsole messages. Unregister
netconsole's console when all net targets are removed. Code
refactoring. Add a number of selftests
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup
- Support inspecting ref_tracker state via DebugFS
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links
- Allow providing upcall pid for the 'execute' command in openvswitch
- Remove DCCP support from Netfilter's conntrack
- Disallow multiple packet duplications in the queuing layer
- Prevent use of deprecated iptables code on PREEMPT_RT
Driver API:
- Support RSS and hashing configuration over ethtool Netlink
- Add dedicated ethtool callbacks for getting and setting hashing
fields
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs
- Support traffic classes in devlink rate API for bandwidth
management
- Remove rtnl_lock dependency from UDP tunnel port configuration
Device drivers:
- Add a new Broadcom driver for 800G Ethernet (bnge)
- Add a standalone driver for Microchip ZL3073x DPLL
- Remove IBM's NETIUCV device driver
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is
used by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading"
* tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1742 commits)
dpll: zl3073x: Fix build failure
selftests: bpf: fix legacy netfilter options
ipv6: annotate data-races around rt->fib6_nsiblings
ipv6: fix possible infinite loop in fib6_info_uses_dev()
ipv6: prevent infinite loop in rt6_nlmsg_size()
ipv6: add a retry logic in net6_rt_notify()
vrf: Drop existing dst reference in vrf_ip6_input_dst
net/sched: taprio: align entry index attr validation with mqprio
net: fsl_pq_mdio: use dev_err_probe
selftests: rtnetlink.sh: remove esp4_offload after test
vsock: remove unnecessary null check in vsock_getname()
igb: xsk: solve negative overflow of nb_pkts in zerocopy mode
stmmac: xsk: fix negative overflow of budget in zerocopy mode
dt-bindings: ieee802154: Convert at86rf230.txt yaml format
net: dsa: microchip: Disable PTP function of KSZ8463
net: dsa: microchip: Setup fiber ports for KSZ8463
net: dsa: microchip: Write switch MAC address differently for KSZ8463
net: dsa: microchip: Use different registers for KSZ8463
net: dsa: microchip: Add KSZ8463 switch support to KSZ DSA driver
dt-bindings: net: dsa: microchip: Add KSZ8463 switch support
...
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wl12xx_cmd_start_fwlog() was added in 2011 by
commit 95dac04f88 ("wl12xx: Support routing FW logs to the host")
but has remained unused.
Remove it.
(I can see the 'stop' is used, and the 'config' is used, so I assume
the 'start' isn't normally needed).
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://patch.msgid.link/20250622232638.166283-1-linux@treblig.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If firmware boot failes, runtime pm is put too often:
[12092.708099] wlcore: ERROR firmware boot failed despite 3 retries
[12092.708099] wl18xx_driver wl18xx.1.auto: Runtime PM usage count underflow!
Fix that by redirecting all error gotos before runtime_get so that runtime is
not put.
Fixes: c40aad28a3 ("wlcore: Make sure firmware is initialized in wl1271_op_add_interface()")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Michael Nemanov <michael.nemanov@ti.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250104195507.402673-1-akemnade@kernel.org
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241216-sysfs-const-bin_attr-net-v1-3-ec460b91f274@weissschuh.net
'struct nla_policy' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
5062 528 0 5590 15d6 drivers/net/wireless/ti/wlcore/testmode.o
After:
=====
text data bss dec hex filename
5178 404 0 5582 15ce drivers/net/wireless/ti/wlcore/testmode.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/78810e3ebb74ddbd3a4538f182bf1143b89baba7.1731332414.git.christophe.jaillet@wanadoo.fr
In order to update the right link information, call the update
rate_control_rate_update() with the right link_sta, and then
pass that through to the driver's sta_rc_update() method. The
software rate control still doesn't support it, but that'll be
skipped by not having a rate control ref.
Since it now operates on a link sta, rename the driver method.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241007144851.5851b6b5fd41.Ibdf50d96afa4b761dd9b9dfd54a1147e77a75329@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Resources definition can become simpler and more organised by
using the dedicated helpers.
Signed-off-by: Vasileios Amoiridis <vassilisamir@gmail.com>
Tested-by: Sabeeh Khan <sabeeh-khan@ti.com>
Reviewed-by: Sabeeh Khan <sabeeh-khan@ti.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240904154919.118513-4-vassilisamir@gmail.com
wlcore_fw_status() is passed a pointer to the struct wl_fw_status to
decode the status into, which is always wl->fw_status. Rather than
referencing wl->fw_status within wlcore_fw_status(), use the supplied
argument so that we access this member in a consistent manner.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/E1sBsxx-00E8vi-Gf@rmk-PC.armlinux.org.uk
Referring to status->counters.tx_lnk_free_pkts[i] multiple times leads
to less efficient code. Cache this value in a local variable. This
also makes the code clearer.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/E1sBsxs-00E8vc-DD@rmk-PC.armlinux.org.uk
Fix the calculation of clear_offset, which may overflow the end of
the buffer. However, this is harmless if it does because in that case
it will be recalculated when we copy the chunk of messages at the
start of the buffer.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/E1sBsxi-00E8vQ-5r@rmk-PC.armlinux.org.uk
Using wl183x devices in AP mode with various firmwares is not stable.
The driver currently adds a station to firmware with basic rates when it
is first known to the stack using the CMD_ADD_PEER command. Once the
station has finished authorising, another CMD_ADD_PEER command is issued
to update the firmware with the rates the station can use.
However, after a random amount of time, the firmware ignores the power
management nullfunc frames from the station, and tries to send packets
while the station is asleep, resulting in lots of retries dropping down
in rate due to no response. This restricts the available bandwidth.
With this happening with several stations, the user visible effect is
the latency of interactive connections increases significantly, packets
get dropped, and in general the WiFi connections become unreliable and
unstable.
Eventually, the firmware transmit queue appears to get stuck - with
packets and blocks allocated that never clear.
TI have a couple of patches that address this, but they touch the
mac80211 core to disable NL80211_FEATURE_FULL_AP_CLIENT_STATE for *all*
wireless drivers, which has the effect of not adding the station to the
stack until later when the rates are known. This is a sledge hammer
approach to solving the problem.
The solution implemented here has the same effect, but without
impacting all drivers.
We delay adding the station to firmware until it has been authorised
in the driver, and correspondingly remove the station when unwinding
from authorised state. Adding the station to firmware allocates a hlid,
which will now happen later than the driver expects. Therefore, we need
to track when this happens so that we transmit using the correct hlid.
This patch is an equivalent fix to these two patches in TI's
wilink8-wlan repository:
https://git.ti.com/cgit/wilink8-wlan/build-utilites/tree/patches/kernel_patches/4.19.38/0004-mac80211-patch.patch?h=r8.9&id=a2ee50aa5190ed3b334373d6cd09b1bff56ffcf7https://git.ti.com/cgit/wilink8-wlan/build-utilites/tree/patches/kernel_patches/4.19.38/0005-wlcore-patch.patch?h=r8.9&id=a2ee50aa5190ed3b334373d6cd09b1bff56ffcf7
Reported-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Co-developed-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/E1sClp4-00Evu7-8v@rmk-PC.armlinux.org.uk
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
sprintf() will be converted as weel if they have.
Generally, this patch is generated by
make coccicheck M=<path/to/file> MODE=patch \
COCCI=scripts/coccinelle/api/device_attr_show.cocci
No functional change intended
CC: Kalle Valo <kvalo@kernel.org>
CC: linux-wireless@vger.kernel.org
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240315055211.1347548-3-lizhijian@fujitsu.com
When these failures happen, the warning and call trace is printed which is
excessive. Instead, just print the error but rate limited to prevent warns
to unnecessarily pollute the kernel log buffer and make the serial console
practically unusable.
For example, on an AM625 BeaglePlay board where accessing a SDIO WiFi chip
fails with an -110 (ETIMEDOUT) error:
$ dmesg | grep "sdio write\|read failed (-110)" | wc -l
39
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240228101042.728881-1-javierm@redhat.com
Currently ieee80211_csa_finish() function finalizes CSA by scheduling a
finalizing worker using the deflink. With MLO, there is a need to do it
on a given link basis.
Pass link ID of the link on which CSA needs to be finalized.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-6-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For channel contexts, mac80211 currently uses the cfg80211
chandef struct (control channel, center freq(s), width) to
define towards drivers and internally how these behave. In
fact, there are _two_ such structs used, where the min_def
can reduce bandwidth according to the stations connected.
Unfortunately, with EHT this is longer be sufficient, at
least not for all hardware. EHT requires that non-AP STAs
that are connected to an AP with a lower bandwidth than it
(the AP) advertises (e.g. 160 MHz STA connected to 320 MHz
AP) still be able to receive downlink OFDMA and respond to
trigger frames for uplink OFDMA that specify the position
and bandwidth for the non-AP STA relative to the channel
the AP is using. Therefore, they need to be aware of this,
and at least for some hardware (e.g. Intel) this awareness
is in the hardware. As a result, use of the "same" channel
may need to be split over two channel contexts where they
differ by the AP being used.
As a first step, introduce a concept of a channel request
('chanreq') for each interface, to control the context it
requests. This step does nothing but reorganise the code,
so that later the AP's chandef can be added to the request
in order to handle the EHT case described above.
Link: https://msgid.link/20240129194108.2e88e48bd2e9.I4256183debe975c5ed71621611206fdbb69ba330@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are some changes coming to wireless-next that will
otherwise cause conflicts, pull wireless in first to be
able to resolve that when applying the individual changes
rather than having to do merge resolution later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the TI WLAN wlcore drivers.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240130104243.3025393-2-leitao@debian.org
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect fw_version strings to be NUL-terminated based on other similar
assignments:
wireless/broadcom/brcm80211/brcmsmac/main.c
7867: snprintf(wlc->wiphy->fw_version,
7868: sizeof(wlc->wiphy->fw_version), "%u.%u", rev, patch);
wireless/broadcom/b43legacy/main.c
1765: snprintf(wiphy->fw_version, sizeof(wiphy->fw_version), "%u.%u",
wireless/broadcom/b43/main.c
2730: snprintf(wiphy->fw_version, sizeof(wiphy->fw_version), "%u.%u",
wireless/intel/iwlwifi/dvm/main.c
1465: snprintf(priv->hw->wiphy->fw_version,
1466: sizeof(priv->hw->wiphy->fw_version),
wireless/intel/ipw2x00/ipw2100.c
5905: snprintf(info->fw_version, sizeof(info->fw_version), "%s:%d:%s",
Based on this, NUL-padding is not required.
A suitable replacement is `strscpy` [2] due to the fact that it
guarantees NUL-termination on the destination buffer without
unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231018-strncpy-drivers-net-wireless-ti-wlcore-main-c-v1-1-1b1055f482a1@google.com
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
wlcore_remove() returned zero unconditionally. With that converted to
return void instead, the wl12xx and wl18xx driver can be converted to
.remove_new trivially.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230912171249.755901-1-u.kleine-koenig@pengutronix.de
This allows to finalize the CSA per link.
In case the switch didn't work, tear down the MLD connection.
Also pass the ieee80211_bss_conf to post_channel_switch to let the
driver know which link completed the switch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230828130311.3d3eacc88436.Ic2d14e2285aa1646216a56806cfd4a8d0054437c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the module_sdio_driver macro to simplify the code, which is the
same as declaring with module_init() and module_exit().
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230821140345.3140493-1-lizetao1@huawei.com
The driver depends on CONFIG_OF, it is not necessary to use
of_match_ptr() here.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to of_property_read_bool().
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for net/can
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove support for configuring the device via platform data because
there are no users of wl1251_platform_data left in the mainline kernel.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221109224250.2885119-2-dmitry.torokhov@gmail.com
First set of patches v6.2. mac80211 refactoring continues for Wi-Fi 7.
All mac80211 driver are now converted to use internal TX queues, this
might cause some regressions so we wanted to do this early in the
cycle.
Note: wireless tree was merged[1] to wireless-next to avoid some
conflicts with mac80211 patches between the trees. Unfortunately there
are still two smaller conflicts in net/mac80211/util.c which Stephen
also reported[2]. In the first conflict initialise scratch_len to
"params->scratch_len ?: 3 * params->len" (note number 3, not 2!) and
in the second conflict take the version which uses elems->scratch_pos.
Git diff output should like this:
--- a/net/mac80211/util.c
+++ b/net/mac80211/util.c
@@@ -1506,7 -1648,7 +1650,7 @@@ ieee802_11_parse_elems_full(struct ieee
const struct element *non_inherit = NULL;
u8 *nontransmitted_profile;
int nontransmitted_profile_len = 0;
- size_t scratch_len = params->len;
- size_t scratch_len = params->scratch_len ?: 2 * params->len;
++ size_t scratch_len = params->scratch_len ?: 3 * params->len;
elems = kzalloc(sizeof(*elems) + scratch_len, GFP_ATOMIC);
if (!elems)
[1] https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next.git/commit/?id=dfd2d876b3fda1790bc0239ba4c6967e25d16e91
[2] https://lore.kernel.org/all/20221020032340.5cf101c0@canb.auug.org.au/
Major changes:
mac80211
* preparation for Wi-Fi 7 Multi-Link Operation (MLO) continues
* add API to show the link STAs in debugfs
* all mac80211 drivers are now using mac80211 internal TX queues (iTXQs)
rtw89
* support 8852BE
rtl8xxxu
* support RTL8188FU
brmfmac
* support two station interfaces concurrently
bcma
* support SPROM rev 11
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmNb2KwRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZs6hggAqrmgHaiRbPYlLVE0hFVaGeVXslfpK9nj
ZGr3bwG5FpioxjAsI7NfwEwpq+FoxTUigG/SShw1Rr8lw43Nt7E57+5McK3qWdKC
5/WndfChPppjtJUpc6PN+UcmCuhcm4TAyMAojbTe5lJ9cJ4yyOWZChDwah3BVZQk
/tHK4qKq8gpppwgkiJ88VdTVoVv5anIvXHH3lAIteljxk0zkaEM7lIQhIFst/zpX
cu/cWvKz2Rh6vnYjkzl8BcrbW8e0/VwnzWggtWs4/kIuRVnHRrrGwlnsULShOscM
fmK+RI2CbJIMucttUOHOXjCg4wwppSit1rH4xOkcwlvrFa7AvDbdHg==
=Zils
-----END PGP SIGNATURE-----
Kalle Valo says:
====================
pull-request: wireless-next-2022-10-28
First set of patches v6.2. mac80211 refactoring continues for Wi-Fi 7.
All mac80211 driver are now converted to use internal TX queues, this
might cause some regressions so we wanted to do this early in the
cycle.
Note: wireless tree was merged[1] to wireless-next to avoid some
conflicts with mac80211 patches between the trees. Unfortunately there
are still two smaller conflicts in net/mac80211/util.c which Stephen
also reported[2]. In the first conflict initialise scratch_len to
"params->scratch_len ?: 3 * params->len" (note number 3, not 2!) and
in the second conflict take the version which uses elems->scratch_pos.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next.git/commit/?id=dfd2d876b3fda1790bc0239ba4c6967e25d16e91
[2] https://lore.kernel.org/all/20221020032340.5cf101c0@canb.auug.org.au/
mac80211
- preparation for Wi-Fi 7 Multi-Link Operation (MLO) continues
- add API to show the link STAs in debugfs
- all mac80211 drivers are now using mac80211 internal TX queues (iTXQs)
rtw89
- support 8852BE
rtl8xxxu
- support RTL8188FU
brmfmac
- support two station interfaces concurrently
bcma
- support SPROM rev 11
====================
Link: https://lore.kernel.org/r/20221028132943.304ECC433B5@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The prandom_u32() function has been a deprecated inline wrapper around
get_random_u32() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. The same also applies to get_random_int(), which is
just a wrapper around get_random_u32(). This was done as a basic find
and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> # for sch_cake
Acked-by: Chuck Lever <chuck.lever@oracle.com> # for nfsd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for thunderbolt
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Acked-by: Helge Deller <deller@gmx.de> # for parisc
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
mac80211 is fully switching over to the internal TX queue (iTXQ)
implementation. Update all drivers not yet providing the now mandatory
wake_tx_queue() callback.
As an side effect the netdev interfaces of all updated drivers will
switch to the noqueue qdisc.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[add staging drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a link_id parameter to ieee80211_nullfunc_get() to be
able to obtain a correctly addressed frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since mac80211 already has a protected pointer to link_conf,
pass it to the driver to avoid additional RCU locking.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This really shouldn't be in a per-link config, we don't want
to let anyone control it that way (if anything, link powersave
could be forced through APIs to activate/deactivate a link),
and we don't support powersave in software with devices that
can do MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the channel context code MLO aware, along with some
functions that it uses, so that the chan.c file is now
MLD-clean and no longer uses deflink/bss_conf/etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
First set of patches for v5.19 and this is a big one. We have two new
drivers, a change in mac80211 STA API affecting most drivers and
ath11k getting support for WCN6750. And as usual lots of fixes and
cleanups all over.
Major changes:
new drivers
* wfx: silicon labs devices
* plfxlc: pureLiFi X, XL, XC devices
mac80211
* host based BSS color collision detection
* prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support
rtw88
* support TP-Link T2E devices
rtw89
* support firmware crash simulation
* preparation for 8852ce hardware support
ath11k
* Wake-on-WLAN support for QCA6390 and WCN6855
* device recovery (firmware restart) support for QCA6390 and WCN6855
* support setting Specific Absorption Rate (SAR) for WCN6855
* read country code from SMBIOS for WCN6855/QCA6390
* support for WCN6750
wcn36xx
* support for transmit rate reporting to user space
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmJxS2sRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuNgwf9H2oxMKLKrlFoX1qHtNBwZuHS6IERhOkM
NI9DjS4MCyiUSbA5r3sWlpqXQeKIbG/05gUZ6Y0ircGFwnAGjZ6isPwo8pKFgbh5
QljXQjUTHbkshrXW8K+VGJxw4F1oiPlOGUDVdXPy2FLx5ZvBlaUV2rWQUzsWX9I0
EnrM6ygHBVejVYDe+JSkb1gzb/07xuZN410IJPuZTPKJfYiE0oGU3zpTbExFitaz
ObjfFUWqHrVue525WFAJ9Dbk8kYEKyMThr7rkkWekYJjujJLJo0qhEiZVZu0eEsk
Vq4PdKmQAqlgbShQ/3Mv8BRsSH2wy62+zKjPWL+8t4Gmm9DbLu+++A==
=T7Ii
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v5.19
First set of patches for v5.19 and this is a big one. We have two new
drivers, a change in mac80211 STA API affecting most drivers and
ath11k getting support for WCN6750. And as usual lots of fixes and
cleanups all over.
Major changes:
new drivers
- wfx: silicon labs devices
- plfxlc: pureLiFi X, XL, XC devices
mac80211
- host based BSS color collision detection
- prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support
rtw88
- support TP-Link T2E devices
rtw89
- support firmware crash simulation
- preparation for 8852ce hardware support
ath11k
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support for QCA6390 and WCN6855
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- support for WCN6750
wcn36xx
- support for transmit rate reporting to user space
* tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (228 commits)
rtw89: 8852c: rfk: add DPK
rtw89: 8852c: rfk: add IQK
rtw89: 8852c: rfk: add RX DCK
rtw89: 8852c: rfk: add RCK
rtw89: 8852c: rfk: add TSSI
rtw89: 8852c: rfk: add LCK
rtw89: 8852c: rfk: add DACK
rtw89: 8852c: rfk: add RFK tables
plfxlc: fix le16_to_cpu warning for beacon_interval
rtw88: remove a copy of the NAPI_POLL_WEIGHT define
carl9170: tx: fix an incorrect use of list iterator
wil6210: use NAPI_POLL_WEIGHT for napi budget
ath10k: remove a copy of the NAPI_POLL_WEIGHT define
ath11k: Add support for WCN6750 device
ath11k: Datapath changes to support WCN6750
ath11k: HAL changes to support WCN6750
ath11k: Add QMI changes for WCN6750
ath11k: Fetch device information via QMI for WCN6750
ath11k: Add register access logic for WCN6750
ath11k: Add HW params for WCN6750
...
====================
Link: https://lore.kernel.org/r/20220503153622.C1671C385A4@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420090247.2588680-1-chi.minghao@zte.com.cn
