To notify firmware TDMA timeslot assignment, append TDMA parameters when
sending policy H2C firmware command. However, compiler warns we do memcpy()
data to val[] field of TLV struct. To avoid this, assign the struct value
with simple '=' instead. Compile tested only.
rtw89/coex.c: In function '_append_tdma':
drivers/net/wireless/realtek/rtw89/coex.c:1585:17:
warning: writing 8 bytes into a region of size 0 [-Wstringop-overflow=]
1585 | memcpy(&v3->tdma, &dm->tdma, sizeof(v3->tdma));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/realtek/rtw89/coex.h:8,
from drivers/net/wireless/realtek/rtw89/coex.c:5:
drivers/net/wireless/realtek/rtw89/core.h:2703:37:
note: at offset [5714, 71249] into destination object 'ver' of size 8
2703 | const struct rtw89_btc_ver *ver;
| ^~~
drivers/net/wireless/realtek/rtw89/coex.c:1579:17:
warning: writing 8 bytes into a region of size 0 [-Wstringop-overflow=]
1579 | memcpy(v, &dm->tdma, sizeof(*v));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw89/core.h:2703:37:
note: at offset [5710, 71245] into destination object 'ver' of size 8
2703 | const struct rtw89_btc_ver *ver;
| ^~~
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310301908.Wrj0diqe-lkp@intel.com/
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231102003716.25815-1-pkshih@realtek.com
For normal use, we do additional settings than mac_pre_init, such as
more TX/RX DMA channels, interrupt mitigation and etc.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-6-pkshih@realtek.com
PCI LTR (Latency Tolerance Reporting) is a capability to yield expected
power consumption, and we configure the parameters according to design.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-5-pkshih@realtek.com
Call this function when doing MAC initialization at probe stage. It does
partial initial registers only, because we only need basic ability to
download firmware. The function to clear index is the sub-function,
so set its pointer as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-4-pkshih@realtek.com
Use gen_def pointer to call three WiFi 6 specific functions, and add _ax
suffix to them. Then, we will implement functions for WiFi 7 chips later.
The mac_{pre,post}_init are used to initialize PCI during doing MAC
initialization, and clear PCI ring index to make index consistent between
driver, firmware and hardware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-3-pkshih@realtek.com
In order to reuse PCI initial and configuration flows, add struct
rtw89_pci_gen_def to abstract the differences between WiFi 6/7 generations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-2-pkshih@realtek.com
PHY status IEs is used to have more information about received packets,
such as RSSI and EVM. For each PHY IE type, it has different predefined
PHY IE length, and the length are changed, so add them for WiFi 7 chips
accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231027015059.10032-5-pkshih@realtek.com
For WiFi 7 chips, some fields and predefined length are changed, so
add them accordingly.
The mac_id field is used to identify peer that send a packet, and we can
use it to know RSSI and traffic from the peer. For WiFi 7 chips,
RXWD.mac_id of PPDU status packet is not set by hardware. Instead, we
should fill it by rxinfo_user[].mac_id of PPDU status content.
Also, filter out invalid reports to prevent warning messages keep showing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231027015059.10032-4-pkshih@realtek.com
Different chip can support different max user in one PPDU report.
So, we now configure it in chip info.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231027015059.10032-3-pkshih@realtek.com
The new chips change hardware design to shrink entry size of address
CAM from 0x40 to 0x20, so make this change accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231027015059.10032-2-pkshih@realtek.com
The register to enable/disable PCI DMA IO has many variants, so define
and use a field to control it accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026120049.9187-5-pkshih@realtek.com
To make hardware efficient to determine if RX ring is full, introduce new
design that checks if reading and writing indices are equal. Comparing
to old design, initial indices of both reading and writing indices are 0
that means empty, and hardware checks full by "writing index + 1 ==
reading index". The "+1" has extra cost for hardware, so new design is
to avoid this.
Take ring size is 256 as an example, the initial reading and writing
indices are 255 and 0 respectively; the initial values mean empty. If two
indices are the same, for example 5 and 5, it means ring is full.
wp rp used_cnt state
255 0 0 initial (ring is empty)
255 1 1 receive 1st packet
255 2 2 receive 2nd packet
0 2 1 driver read 1st packet
1 2 0 driver read 2nd packet (ring is empty)
:
5 5 255 ring is full
Note: 'rp' is hardware writing index
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026120049.9187-4-pkshih@realtek.com
PCI rings are used to DMA TX/RX packets. The address of WiFi 7 chips are
different from previous ones, so add them according to hardware design.
Another difference is that driver doesn't need to configure BD (buffer
descriptor) RAM table, which is used by hardware to fetch BD ahead before
fetching whole TX data.
A TX ring contains numbers of TX BD (e.g. 512):
TX BD (buffer descriptor; continual memory)
+---+---+---+---+ +---+
| | | | | ... | |
+-|-+---+---+---+ +---+
|
| point to TX WD (WiFi descriptor; metadata of a skb data)
v
+------+
| |
| |
+-|----+
|
| point to a skb data
v
+------+
| |
| |
+------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026120049.9187-3-pkshih@realtek.com
8922AE is a PCIE 802.11be wireless adapter with PID 0x8922. We add basic
configurations including PCI DMA mode, PCI parameters, register address to
control TX/RX rings and etc.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026120049.9187-2-pkshih@realtek.com
Since 'rtw89_core_tx_kick_off_and_wait()' assumes timeout
(actually RTW89_ROC_TX_TIMEOUT) in milliseconds, I suppose
that RTW89_ROC_IDLE_TIMEOUT is in milliseconds as well. If
so, 'msecs_to_jiffies()' should be used in a call to
'ieee80211_queue_delayed_work()' from 'rtw89_roc_end()'.
Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231024143137.30393-1-dmantipov@yandex.ru
The third, and most likely the last, features pull request for v6.7.
Fixes all over and only few small new features.
Major changes:
iwlwifi
* more Multi-Link Operation (MLO) work
ath12k
* QCN9274: mesh support
ath11k
* firmware-2.bin container file format support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmU6KqgRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZtyMwf7B/BqV0LCNzBxtrWl3WYtgQgULgWFmEJt
83/Vo8pXelZzzMMERwvZtPCwEUm/L/vOO/a/k0oSz/XQbt4PTIBGnWA7JwYZGY++
1Kc79oMyXxG4Q4RCnKG/qQMzCnyL54RHUfFQrNaa3Bkgp7vGobU+ixH4NaqHI3M9
OFmyhCklk9AO0VTtT6vQQBM6wM3UC1adneZMVlb8xD2Wi5rkrRk4PX5msgaYrStR
ketZE6IPnnX8DziqGZPlTz1SSuOSnwGTOramdeGLKIUUlZbPWHTSBZ8lh/xnvGUB
561mp3/iguFtq2NvduPBqItotBzLGvnJZbLDrBPxB/v99q+7/cziSA==
=Xf7b
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-10-26' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.7
The third, and most likely the last, features pull request for v6.7.
Fixes all over and only few small new features.
Major changes:
iwlwifi
- more Multi-Link Operation (MLO) work
ath12k
- QCN9274: mesh support
ath11k
- firmware-2.bin container file format support
* tag 'wireless-next-2023-10-26' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (155 commits)
wifi: ray_cs: Remove unnecessary (void*) conversions
Revert "wifi: ath11k: call ath11k_mac_fils_discovery() without condition"
wifi: ath12k: Introduce and use ath12k_sta_to_arsta()
wifi: ath12k: fix htt mlo-offset event locking
wifi: ath12k: fix dfs-radar and temperature event locking
wifi: ath11k: fix gtk offload status event locking
wifi: ath11k: fix htt pktlog locking
wifi: ath11k: fix dfs radar event locking
wifi: ath11k: fix temperature event locking
wifi: ath12k: rename the sc naming convention to ab
wifi: ath12k: rename the wmi_sc naming convention to wmi_ab
wifi: ath11k: add firmware-2.bin support
wifi: ath11k: qmi: refactor ath11k_qmi_m3_load()
wifi: rtw89: cleanup firmware elements parsing
wifi: rt2x00: rework MT7620 PA/LNA RF calibration
wifi: rt2x00: rework MT7620 channel config function
wifi: rt2x00: improve MT7620 register initialization
MAINTAINERS: wifi: rt2x00: drop Helmut Schaa
wifi: wlcore: main: replace deprecated strncpy with strscpy
wifi: wlcore: boot: replace deprecated strncpy with strscpy
...
====================
Link: https://lore.kernel.org/r/20231026090411.B2426C433CB@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When compiling with clang-18, I've noticed the following:
drivers/net/wireless/realtek/rtw89/fw.c:389:28: warning: cast to smaller
integer type 'enum rtw89_fw_type' from 'const void *' [-Wvoid-pointer-to-enum-cast]
389 | enum rtw89_fw_type type = (enum rtw89_fw_type)data;
| ^~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw89/fw.c:569:13: warning: cast to smaller
integer type 'enum rtw89_rf_path' from 'const void *' [-Wvoid-pointer-to-enum-cast]
569 | rf_path = (enum rtw89_rf_path)data;
| ^~~~~~~~~~~~~~~~~~~~~~~~
So avoid brutal everything-to-const-void-and-back casts, introduce
'union rtw89_fw_element_arg' to pass parameters to element handler
callbacks, and adjust all of the related bits accordingly. Compile
tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231020040940.33154-1-dmantipov@yandex.ru
We currently have napi_if_scheduled_mark_missed that can be used to
check if napi is scheduled but that does more thing than simply checking
it and return a bool. Some driver already implement custom function to
check if napi is scheduled.
Drop these custom function and introduce napi_is_scheduled that simply
check if napi is scheduled atomically.
Update any driver and code that implement a similar check and instead
use this new helper.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We need this register setting only for the software DCFO(digital carrier
frequency offset) compensation so we move it to the proper position to
prevent the incorrect setting.
Signed-off-by: Cheng-Chieh Hsieh <cj.hsieh@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231016065115.751662-6-pkshih@realtek.com
DCFO tracking compensate the CFO (carrier frequency offset) by digital
hardware that provides fine CFO estimation. Although the avg_cfo which
is a coarse information becomes zero, still we need DCFO tracking to
compensate the residual CFO. However, the original flow skips the case
when avg_cfo is zero, so we fix it to have expected performance.
Signed-off-by: Cheng-Chieh Hsieh <cj.hsieh@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231016065115.751662-5-pkshih@realtek.com
The register address used for CFO(carrier frequency offset) tracking is
different from WiFi 7 series, so we change the way to access it. And we
refine the flow of CFO tracking to compatible all WiFi 7 and 6 ICs.
Signed-off-by: Cheng-Chieh Hsieh <cj.hsieh@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231016065115.751662-4-pkshih@realtek.com
The register fields of BSS color map and valid bit are in the same register
for existing chips, but coming WiFi 7 chips define another register to
set valid bit, so add a field to chip_info to reuse the code.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231016065115.751662-3-pkshih@realtek.com
Change naming to disambiguate the functions because their names are common
and not clear about the purpose. Not change logic at all.
These functions are to control baseband AGC while BT coexists with WiFi.
Among these functions, ctrl_btg_bt_rx is used to control AGC related
settings, which is affected by BT RX, while BT shares the same path
with wifi; ctrl_nbtg_bt_tx is used to control AGC settings under
non-shared path condition, which is affected by BT TX.
Signed-off-by: Chung-Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231016065115.751662-2-pkshih@realtek.com
Beamforming monitor is used to adjust registers to fine tune performance
and power save, and currently only existing WiFi 6 chips need it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-7-pkshih@realtek.com
When associated peer has beamformer capability, we should enable
beamformee, set CSI parameter, and configure rate to send CSI packets.
Since registers of WiFi 7 chips are very different from existing chips,
separate configuration functions.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-6-pkshih@realtek.com
When associated peer has beamformer capability, enable hardware beamformee
function, and then hardware can run sounding protocol itself. Oppositely,
disable this function when disassociated. Define different registers for
WiFi 6 and 7 generations respectively.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-5-pkshih@realtek.com
When connected with 802.11ax AP, MU-EDCA parameters are given, so enable
this hardware function by registers according to chip generation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-3-pkshih@realtek.com
When TX size or time of packet over RTS threshold set by this register,
hardware will use RTS protection automatically. Since WiFi 6 and 7 chips
have different register address for this, separate the address according
to chip gen.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-2-pkshih@realtek.com
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time via CONFIG_UBSAN_BOUNDS (for
array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
Use struct_size() and flex_array_size() helpers to calculate proper sizes
for allocation and memcpy().
Don't change logic at all, and result is identical as before.
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231011063725.25276-2-pkshih@realtek.com
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time via CONFIG_UBSAN_BOUNDS (for
array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
Use struct_size() and flex_array_size() helpers to calculate proper sizes
for allocation and memcpy().
Don't change logic at all, and result is identical as before.
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231011063725.25276-1-pkshih@realtek.com
Add IEEE80211_RADIOTAP_EHT and IEEE80211_RADIOTAP_EHT_USIG radiotap to
fill basic EHT NSS, MCS, GI and bandwidth.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231011115256.6121-7-pkshih@realtek.com
Since we have TX rate from RA report of C2H event and RX rate from RX
descriptor, show them in debugfs like
TX rate [1]: EHT 2SS MCS-7 GI:3.2 BW:80 (hw_rate=0x427)
RX rate [1]: EHT 2SS MCS-7 GI:3.2 BW:80 (hw_rate=0x427)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231011115256.6121-6-pkshih@realtek.com
RA (rate adaptive) C2H report is to reflect current TX rate firmware is
using. Parse C2H event encoded in EHT mode, and then user space and debugfs
can use the information to know TX rate.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231011115256.6121-5-pkshih@realtek.com
Set EHT rate mask to RA (rate adaptive) H2C command according to handshake
result. The EHT rate mask format looks like
44 28 12 4 0
+----------------+----------------+--------+----+
| EHT 2SS rate | EHT 1SS rate | OFDM | CCK|
+----------------+----------------+--------+----+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231011115256.6121-4-pkshih@realtek.com
There are two kinds of RX packets -- normal and its PPDU status packet.
Both have RX descriptor containing some information such as rate, GI and
bandwidth, and we use these information to find the relationship between
two kinds of packets. Then, we can get more information like RSSI and EVM
from PPDU status packet.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231011115256.6121-3-pkshih@realtek.com
Since current TX power stuffs are for ax chips, add a suffix `_ax` to
them. Then, when requested to show txpwr table, select table according
to chip generation first.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231003015446.14658-7-pkshih@realtek.com
Wi-Fi 6 chips and Wi-Fi 7 chips have different register design for TX
power RU limit. We rename original setting stuffs with a suffix `_ax`,
concentrate related enum declaration in phy.h, and implement setting
flow for Wi-Fi 7 chips. Then, we set TX power RU limit according to
chip generation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231003015446.14658-6-pkshih@realtek.com
Wi-Fi 6 chips and Wi-Fi 7 chips have different register design for
TX power limit. We rename original setting stuffs with a suffix `_ax`,
concentrate related enum declaration in phy.h, and implement setting
flow for Wi-Fi 7 chips. Then, we set TX power limit according to chip
generation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231003015446.14658-5-pkshih@realtek.com
We have a register to control TX power of each rate section to increase
or decrease an offset. But, Wi-Fi 6 chips and Wi-Fi 7 chips have different
address and format for this control register. We rename original setting
stuffs with a suffix `_ax` and implement setting flow for Wi-Fi 7 chips.
Then, we set TX power offset according to chip generation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231003015446.14658-4-pkshih@realtek.com
Wi-Fi 6 chips and Wi-Fi 7 chips have different register design for
TX power by rate. We rename original setting stuffs with a suffix
`_ax` and implement setting flow for Wi-Fi 7 chips. Then, we set TX
power by rate according to chip generation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231003015446.14658-3-pkshih@realtek.com
There are two difference between Wi-Fi 6 and Wi-Fi 7 chips.
1. Address range of TX power control register
2. Checking code to get a TX power control register
So, separate the implementation of them, access according to
chip generation, and rename original things with a suffix `_ax`.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231003015446.14658-2-pkshih@realtek.com
This improves 160MHz performance degradation with certain APs.
Some ICs transmit preamble that are hard to decode by others, continuous
retries then yield low throughput. Fix it with pre-calculated antenna
matrices.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230929004024.7504-3-pkshih@realtek.com
Rename support_ul_tb_ctrl to waveform_ctrl since we need to do more
trigger based control and the naming could be confusing. Move related
code to leaf function so we make each functions separate and can be
easier to maintain.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230929004024.7504-2-pkshih@realtek.com
Update TX power tables to RF version R34.
* tweak values of CN for its new regulation
* add TX power by rate table for RFE (RF Front End) type 2
* add TX shape table for RU limit
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Update TX power tables to RF version R35.
* tweak values of CN for its new regulation
* add TX shape table for RU limit
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Update TX power tables to RF version R67.
* tweak values of CN for its new regulation
* configure values of Thailand for its regulation
* add TX shape table for RU limit
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Realtek RFE (RF Front End) parameters can consider Thailand individually
now, so we add it into regulation type enum. Then, we map country code TH
to RTW89_ETSI/RTW89_THAILAND according to band. The RF TX power tables will
add entries for RTW89_THAILAND in the following.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
MCC (multi-channel concurrency) supports two combinations as below.
* P2P-GO + STA
* P2P-GC + STA
We add the corresponding ieee80211_iface_limit for it into
ieee80211_iface_combination.
Besides, for multiple channels, it must run with mac80211 chanctx.
So, only with it, ieee80211_iface_combination can allow MCC case.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230921003559.11588-5-pkshih@realtek.com
We are going to allow RTL8852C to support MCC (multi-channel concurrency).
So, we increase 8852c::support_chanctx_num up to 2.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230921003559.11588-4-pkshih@realtek.com
During (TDMA-based) MCC (multi-channel concurrency), the below two
cases might not have a good behavior on channel usage.
* ROC (remain on channel)
* HW scan
So, we tend to separate them from MCC.
The two cases would expect to operate the channel to which they want.
However, during MCC, channels are scheduled by FW MCC state mechanism.
So, channels cannot be controlled explicitly. To avoid the two cases
from operating wrong channels with chance, we pause MCC (essentially
stop FW MCC) once the two cases are coming. And then, we proceed MCC
again (essentially restart FW MCC) once the two cases finish.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230921003559.11588-3-pkshih@realtek.com
Under TDMA-based MCC (multi-channel concurrency), there are two roles,
reference and auxiliary. We arrange MCC timeline based on time domain
of reference role. Then, we calculate NoA start time according to MCC
timeline.
Besides, when MCC runs GO+STA mode, we plan an offset between GO time
domain and STA time domain to make their TBTTs have a time gap.
However, if GO is auxiliary role instead of reference role, NoA start
time is described by STA time domain instead of GO time domain. To fix
this, we apply the offset mentioned above to NoA start time to convert
time domain from STA to GO.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230921003559.11588-2-pkshih@realtek.com
The following FW elements are recognized, and then the valid entries
in them are loaded into SW struct case by case.
* TX power by rate
* TX power limit 2 GHz
* TX power limit 5 GHz
* TX power limit 6 GHz
* TX power limit RU 2 GHz
* TX power limit RU 5 GHz
* TX power limit RU 6 GHz
* TX shape limit
* TX shape limit RU
One single firmware file can contain multiples of each of the above FW
elements. Each of them is configured with a target RFE (RF front end)
type. We choose one of the multiples to load based on RFE type. If there
are multiples of the same FW elements with the same target RFE type. The
last one will be applied.
We don't want to have many loading variants for above FW elements. Even if
between different chips or between different generations, we would like to
maintain only one single set of loadings. So, the loadings are designed to
consider compatibility. The main concepts are listed below.
* The driver structures, which are used to cast binary entry from FW,
cannot insert new members in the middle. If there are something new,
they should always be appended at the tail.
* Each binary entry from FW uses a dictionary way containing a key set
and a data. The keys in the key set indicate where to put the data.
* If size of driver struct and size of binary entry do not match when
loading, it means the number of keys in the key set are different.
Then, we deal with compatibility. No matter which one has more keys,
we take/use zero on those mismatched keys.
If driver struct is bigger (backward compatibility):
e.g. SW uses two keys, but FW is built with one key.
Then, put the data of FW(keyX) into SW[keyX][0].
If binary entry is bigger (forward compatibility):
e.g. FW is built with two keys, but SW uses one key.
Then, only take the data of FW(keyX, keyY = 0) into SW[keyX]
Besides, chip info setup flow is tweaked a bit for the following.
* Before loading FW elements, we need to determine chip RFE via efuse.
* Setting up RFE parameters depends on loading FW elements ahead.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230920074322.42898-8-pkshih@realtek.com
The following are introduced for Wi-Fi 7 chips.
1. take BW/OFDMA into account on TX power by rate
2. increase TX power offset types up to EHT
3. split TX shape into tx_shape_lmt and tx_shape_lmt_ru
If functions which are only for AX, they always access TX power by rate
with BW/OFDMA = 0/0, and they don't access tx_shape's lmt_ru section.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230920074322.42898-7-pkshih@realtek.com
Table of TX power by rate only needs to be loaded once. But, we originally
loaded it every time we start core. Now, we load it one time along as RFE
(RF Front End) parameters are determined.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230920074322.42898-6-pkshih@realtek.com
Originally, these helpers were implemented by macros. We rewrite them
by normal functions. In the new function to seek raw TX power by rate,
we access the array according to rate section and discard the original
pointer arithmetic.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230920074322.42898-5-pkshih@realtek.com
For next-generation chips, TX power by rate table comes from RFE (RF
front end) parameter. It can be different according to RFE type. So,
we indicate TX power by rate table inside RFE parameter ahead. For
current chips, even with different RFE types, a chip is configured
with a single TX power by rate table. So, this commit doesn't really
affect these currently supported chips.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230920074322.42898-4-pkshih@realtek.com
For next-generation chips, TX shape table comes from RFE (RF front end)
parameter. It can be different according to RFE type. So, we indicate
TX shape table inside RFE parameter ahead. For current chips, even with
different RFE types, a chip is configured with a single TX shape table.
So, this commit doesn't really affect these currently supported chips.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230920074322.42898-3-pkshih@realtek.com
The subband index is a hardware value of relationship between primary
channel and bandwidth, and it is used by setting channel/bandwidth to
specify the primary channel.
Because this index is only needed when bandwidth >= 20 MHz, adjust
order of enumerator bandwidth to access offsets array easier. To prevent
misuse RTW89_CHANNEL_WIDTH_NUM as size, change it to
RTW89_CHANNEL_WIDTH_ORDINARY_NUM that will be the size of array. The
enumerator values of bandwidth (before ordinary number) will be also
used by upcoming TX power table built in firmware file, so add a comment
to remind keeping the order.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230920074322.42898-2-pkshih@realtek.com
Using mac_gen pointer to reuse the code with WiFi 7 chips, and define
MAC ports registers for WiFi 7 chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230911082049.33541-7-pkshih@realtek.com
MAC port is a design to support virtual interface on single MAC hardware.
For next generation chips, register addresses are changed but definitions
are the same, so move registers together to be easier to reuse codes.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230911082049.33541-6-pkshih@realtek.com
For existing chips, size of TX WD info is 6 words, but upcoming WiFi 7
chips become 8 words, so add a chip_info to reuse the code.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230911082049.33541-5-pkshih@realtek.com
The format v2 of TX descriptor contains 8-word body and 8-word info, and
fields include packet size, MAC_ID, security key ID and etc.
By design, it can possibly only fill body to reduce overhead, but this
driver keeps thing simple, so always fill body and info currently.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230911082049.33541-4-pkshih@realtek.com
This kind of TX descriptor is used to download firmware or send firmware
command. Because we want to reduce descriptor overhead and this only needs
two fields 'size' and 'type', hardware designers choose short form of
RX descriptor for it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230911082049.33541-3-pkshih@realtek.com
RX descriptor is used to provide meta data of received data. The WiFi 7
chips use different RX descriptor format, so add this parser along with
hardware design.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230911082049.33541-2-pkshih@realtek.com
In MCC STA+GO mode, we calculate NoA information and fill it into the
beacon of P2P GO. Since NoA uses only 32 bits to describe time things,
we need to deal with renewal when TSF[63:32] is carried. We trigger FW
to notify that. Then, we can update NoA information for new time period
once we get notification from FW.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-9-pkshih@realtek.com
When receiving request of adjusting BT slot from coex. mechanism,
we need to fetch the new BT slot and use the new one to calculate
MCC (multi-channel concurrency) pattern. Then, we update the new
MCC pattern to FW.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-8-pkshih@realtek.com
MCC fills duration limit of a role according to NoA description.
If P2P PS changes during MCC, we don't process P2P PS via normal
flow. Instead, we re-fill duration limit of the role for new NoA
description, and then we do MCC update.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-7-pkshih@realtek.com
In MCC STA+GC mode, the offset between TBTTs of remote AP and remote GO
might change. If the change is larger than tolerance, we should update
MCC after re-calculating parameters for new things. So, we track that in
rtw89_track_work() now. And, we add MCC update flow to tell FW either to
change durations of roles or to replace entire pattern according to how
MCC plans BT slot.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-6-pkshih@realtek.com
Each MCC (multi-channel concurrency) role maintains a bitmap of mac IDs.
The bitmap is supposed to contain the two points below.
* mac ID of itself
* mac ID(s) of STA(s) connecting to it
Under STA+GC mode, the bitmaps of both roles should not change. However,
under STA+GO mode, the bitmap of GO may change due to P2P clients which
connect/disconnect to/from it.
FW controls (TDMA-based) MCC things via mac IDs in bitmap of each role.
For example, mac IDs are required by FW when it wants to pause role1's
TX in role0 slot.
So, to sync between driver and FW, we update the new mac ID bitmap of GO
to FW once it's changed.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-5-pkshih@realtek.com
DPK is one kind of RF calibration. When MCC (multi-channel concurrency)
start/stop, DPK needs to do extra things to be off/on. We add a chanctx
callback type, RTW89_CHANCTX_CALLBACK_RFK, and register it for RTL8852C
to deal with DPK according to MCC states.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-4-pkshih@realtek.com
After MCC (multi-channel concurrency) is started, FW will control channel
changes and use the corresponding backup of RF calibration result. And,
driver RF calibration (RF-K) won't be able to keep up with the speed at
which the channels are changing. So, even if we keep tracking it in driver,
the RF-K result might not be good either. To save these unnecessary things,
we disable driver RF-K tracking during MCC.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-3-pkshih@realtek.com
RF calibration will notify FW to backup the calibration result after it
is done on a channel. For MCC (multi-channel concurrency) flow, when we
at RTW89_ENTITY_MODE_MCC_PREPARE mode, RF calibration should execute on
second channel of MCC, i.e. RTW89_SUB_ENTITY_1, and then, notify FW to
backup the result for the second one.
Originally, the RF calibration flow only fit single channel case. We are
planning to support MCC on RTL8852C, so we refine its RF calibration flow
to fit MCC case.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-2-pkshih@realtek.com
There were are a number of cases in mac80211 and iwlwifi (at
least) that used the sband->iftype_data pointer directly,
instead of using the accessors to find the right array entry
to use.
Make sparse warn when such a thing is done.
To not have a lot of casts, add two helper functions/macros
- ieee80211_set_sband_iftype_data()
- for_each_sband_iftype_data()
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Secure firmware is protected by public/private key cryptography. To help
firmware self verify integrity, configure a heap address for these
data before downloading firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-9-pkshih@realtek.com
To support download more than one firmware, adjust flow to download
firmware by unit of firmware suit. Then, flow becomes
1. initial setup - disable/enable_wcpu
2. for all firmware suits
2.1. download WiFi CPU, and check ready
2.2. download BB MCU, and check ready
3. check status code to make sure all ready
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-8-pkshih@realtek.com
Though WiFi 7 chips need BB MCU firmware, we don't download it in probe
stage. Instead, only bring interface up under normal operation or WoWLAN
mode. So, add an argument to assist download flow to setup download
settings properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-6-pkshih@realtek.com
For WiFi 6 chips, there is only single one firmware i.e. WiFi CPU firmware,
so no need an argument to discriminate them. For WiFi 7 chips, BB MCU
firmware is introduced, and we need to check it ready after downloading.
For each type of firmware, we need to check corresponding hardware ready
bit. After downloading all firmware, check status code to determine if
all things are ready.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-5-pkshih@realtek.com
To work with generalized flow of download firmware, implement WiFi 7
specific functions to support it. These functions include disable/enable
WiFi CPU, status of path ready, and status of firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-4-pkshih@realtek.com
In order to reuse the flow to download firmware, define some mac_gen::ops
to implement them for WiFi 6 and 7 chips individually. This doesn't change
logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-3-pkshih@realtek.com
To download firmware, we need to check path is ready. There are two kinds
of path -- one is to download firmware header, and the other is to download
firmware body.
Since the polling method is different from WiFi 7 chips, make it to be
an individual function, and then we can reuse the download flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-2-pkshih@realtek.com
According to Wi-Fi/BT roles' settings, we fill corresponding H2Cs (host
to chip packets). Then, following MCC (multi-channel concurrency) pattern,
we send these H2Cs as planned. Eventually, the trigger H2Cs will be sent
to tell FW to really start/stop MCC.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-7-pkshih@realtek.com
Fix a typo where `bitamp` should be `bitmap`. Don't change functionality
at all.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-6-pkshih@realtek.com
After the previous works, we can now expand and display the MCC pattern
in more detail, as shown below.
|< MCC interval >|
|< duration ref >| (if mid bt) |< duration aux >| (if tail bt) |
|<tob ref >|< toa ref>| ... |<tob aux >|< toa aux>| ... |
V V
tbtt ref tbtt aux
|< beacon offset >|
(where tob means `time offset behind` and toa means `time offset ahead`)
There are two key points.
1. decide position of BT slot if MCC pattern needs to handle BT duration.
2. calculate all parameters related to tob and toa in MCC pattern.
For point (1), when BT duration needs to be handled, BT position will
rely on beacon offset, either middle or tail. For point (2), to ensure
durations of the Wi-Fi roles cover their beacons, we have to calculate
tob and toa for them according to their TBTT.
And, there are two strategies to calculate parameters, strict and loose.
In strict pattern, all parameters take HW time into account as limitation.
But, the strict calculation are not always successful. In loose pattern,
it only tries to give positive parameters to reference role and doesn't
care much about auxiliary role. If unfortunately auxiliary role gets
negative parameters in loose pattern, FW will be notified and then deal
with it. So, the loose calculation won't fail. In general, we always try
strict pattern cases before using a loose pattern.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-5-pkshih@realtek.com
Before calculating MCC pattern, we have to determine whether to handle BT
duration in it or not. The decision will depend on the channels that Wi-Fi
roles use. And, we have three cases shown below.
1. non-2GHz + non-2GHz
2. non-2GHz + 2GHz (different band)
3. 2GHz + 2GHz (dual 2GHz)
For case (1), we don't care BT duration in MCC pattern. For case (2), we
still don't care BT duration in MCC pattern. Instead, we try to satisfy it
by modifying duration of Wi-Fi role on non-2GHz channel. For case (3), we
need to modify Wi-Fi durations and also need to handle BT duration in MCC
pattern.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-4-pkshih@realtek.com
We determine the fundamental settings shown below.
|< MCC interval >|
|< duration ref >|< duration aux >|
| | | |
|< beacon offset >|
| |
V V
(tbtt ref) (tbtt aux)
(where `ref` (reference) and `aux` (auxiliary) mean the two MCC roles)
Based on MCC mode (GO+STA or GC+STA), we fill configurations of
MCC interval and beacon offset. And, we make sure each MCC role
have a basically required duration in the MCC interval.
The beacon offset mentioned above is a parameter for further MCC
pattern calculation. If MCC is in GC+STA mode, we will calculate
the real beacon offset through TSFs shown in beacons of both MCC
roles. Otherwise, we will use a default beacon offset, and make
GO sync STA's TSF timer with this offset.
MCC pattern calculation will break down each MCC role's duration
in more detail. We will implement it in the following.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-3-pkshih@realtek.com
We prepare to support TDMA-based MCC (multi-channel concurrency)
which allows two kinds of modes below.
* P2P GO + normal STA
* P2P GC + normal STA
Each mode has two vif and two chanctx. Then, each vif binds one
separate chanctx and becomes one MCC role. We name the two MCC
roles as follows.
* MCC role - reference (ref)
We calculate the baseline of our TDMA things accodring
to its info, e.g. TBTT. In normal case, it will be put
at the first slot of TDMA.
* MCC role - auxiliary (aux)
MCC state machine will be running in FW eventually, but before that,
we have to fill and calculate things that are needed by FW. We fill
the information of MCC role according to its vif and its chanctx.
Then, we calculate the start time for MCC.
Note that the parameters used in the calculation now is assigned by
default rules. The precise parameters for better MCC behavior will be
derived in the following.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-2-pkshih@realtek.com
TSSI configures bandedge to TX proper waveform, these new bandedge
parameters improve the accuracy of transmit power compensation.
This helps to avoid throughput degradation.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230830092849.153251-2-pkshih@realtek.com
clang warns (or errors with CONFIG_WERROR=y):
drivers/net/wireless/realtek/rtw89/sar.c:216:3: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
216 | case RTW89_TAS_STATE_DPR_FORBID:
| ^
drivers/net/wireless/realtek/rtw89/sar.c:216:3: note: insert 'break;' to avoid fall-through
216 | case RTW89_TAS_STATE_DPR_FORBID:
| ^
| break;
1 error generated.
Clang is a little more pedantic than GCC, which does not warn when
falling through to a case that is just break or return. Clang's version
is more in line with the kernel's own stance in deprecated.rst, which
states that all switch/case blocks must end in either break,
fallthrough, continue, goto, or return. Add the missing break to silence
the warning.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1921
Fixes: eb2624f55a ("wifi: rtw89: Introduce Time Averaged SAR (TAS) feature")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822-rtw89-tas-clang-implicit-fallthrough-v1-1-5cb73f0fa976@kernel.org
The ENV_MNTR(environment monitor) is the dynamic mechanism which based on
the HW of CCX(Cisco Compatible Extensions) which provide the channel
loading and noisy level indicator to debug or support the 802.11k. The
PHYSTS provide the detail PHY information per packet we received for
debugging. The DIG(dynamic initial gain) is the dynamic mechanism to
adjust the packet detect power level by received signal strength to avoid
false detection of the WiFi packet.
The address of registers used for ENV_MNTR, PHYSTS and DIG of WiFi 7 IC
are different with WiFi 6 series, so we modify the method to access the
register address in order to compatible with all WiFi 7 and 6 ICs.
Signed-off-by: Cheng-Chieh Hsieh <cj.hsieh@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-7-pkshih@realtek.com
cr_base is base address of PHY control register. The base of WiFi 6 and 7
chips are 0x1_0000 and 0x2_0000 respectively, so define them accordingly.
For example, if PHY address is 0x1330, absolute address is 0x1_1330 for
WiFi 6 chips, and 0x2_1330 for WiFi 7 chips.
Meanwhile, there are two copies of PHY hardware named PHY0 and PHY1. The
offset between them is 0x2_0000, so the base address of PHY0 and PHY1 are
0x2_0000 and 0x4_0000 respectively.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-6-pkshih@realtek.com
rx_filter is used to decide which kind of packets are received to driver,
or just dropped by MAC layer to reduce bus traffic.
The bit definitions of old and new chips are the sames, but only address
is changed, so define a field to generalize usage.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-5-pkshih@realtek.com
Define base address of WiFi 7 internal memory according to design to
provide the same functions as existing WiFi 6 chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-4-pkshih@realtek.com
To diagnose abnormal behavior, we need to dump certain internal memory.
For example, dump security CAM when debugging encryption/decryption
problems, or dump BA CAM when debugging abnormal BlockAck.
Since the indirect address and internal memory base address are different
between WiFi 6 and 7 chips, add fields to reuse codes.
Also, only WiFi 6 chips initialize DMAC and CMAC tables via this indirect
interface, so no need to change the constant register address, and
new firmware will help to initialize these tables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-3-pkshih@realtek.com
There are two copies of MAC hardware called band0 and band1. Basically,
the only difference between them is base address, so we can share functions
with a 'band' (or 'mac_idx') argument.
The offset of base address of WiFi 6 and 7 are 0x2000 and 0x4000
respectively, so add band1_offset field to new introduced struct
mac_gen_def to possibly reuse functions.
Using below spatch script to convert callers:
@@
expression reg, band;
@@
- rtw89_mac_reg_by_idx(reg, band)
+ rtw89_mac_reg_by_idx(rtwdev, reg, band)
@@
expression reg, port, band;
@@
- rtw89_mac_reg_by_port(reg, port, band)
+ rtw89_mac_reg_by_port(rtwdev, reg, port, band)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-2-pkshih@realtek.com
We prepare to deal with multiple channels via new entity modes.
* MCC_PREPARE: Transitional mode before MCC
* MCC: Multi-Channel Concurrent mode
And, enum of sub-entity is extended for second channel context.
We add the entry flow of multi-channel handling and the core stuffs
for extended index of sub-entity. And, we now deal with the filling
of entity channels' info in entity recalc where we know the number
of active chanctx. However, the other detail coding of MCC start/stop
will be implemented in the following.
Besides, chanctx listener struct is pre-added in chip info. Each
component can add callback type in chanctx listener and configure
its callback function to react according to chanctx states. We know
at least RFK (RF calibration) and BTC (BT coexistence) will require
such callbacks.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-7-pkshih@realtek.com
Callers call renew function when wanting to generate a new P2P NoA
information element, and call append function to append NoA attribute
one by one. Then, updating beacon work will fetch the P2P NoA information
element configured by callers and add it to beacon.
The use case of MCC (multi-channel concurrent) <GO + STA> for example:
* start MCC - GO part
renew P2P NoA
append period NoA after calculation
* download beacon for GO
fetch P2P NoA and add to beacon content
* stop MCC - GO part
renew P2P NoA (reset)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-6-pkshih@realtek.com
We adjust these processes which can work accodrding to vif but call
rtw89_chan_get() with static RTW89_SUB_ENTITY_0. After multi-channel
support, chanctx of vif won't always be on RTW89_SUB_ENTITY_0. So,
we make them call rtw89_chan_get() with rtwvif->sub_entity_idx.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-5-pkshih@realtek.com
If multiple channels, SAR will be hard to determine the center frequency
to query. Therefore, we move this decision out of SAR.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-4-pkshih@realtek.com
In rtw89_correct_cck_chan(), we turn to use rtw89_hw_to_nl80211_band().
The difference between rtw89_hw_to_nl80211_band() and the original raw
judgement is the case on 6 GHz. Since rtw89_correct_cck_chan() is common
code independent on chip, if runtime chip doesn't support 6 GHz, it is
probably safe. Otherwise, it might not.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-3-pkshih@realtek.com
The request duration comes from coex mechanism, indicating the
length of time that should be reserved for BT in each time division.
It is required to handle update notification when channel concurrency
processes. Since it will involve in both coex and wifi code flow, this
commit ahead adds the prototype for required function interfaces to
split the implementation of coex and wifi in the following.
The follow-up are expected be add afterwards.
1. coex mechanism call rtw89_core_ntfy_btc_event() once bt req len changes
2. channel concurrency flow updates related stuffs when notified
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-2-pkshih@realtek.com
A mouse that uses a USB connection is called a "USB mouse" device (or
"USB mouse" for short), not a "mouse USB" device. By analogy, a WiFi
adapter that connects to the host computer via USB is a "USB wireless"
device, not a "wireless USB" device. (The latter term more properly
refers to a defunct Wireless USB specification, which described a
technology for sending USB protocol messages over an ultra wideband
radio link.)
Similarly for a WiFi adapter card that plugs into a PCIe slot: It is a
"PCIe wireless" device, not a "wireless PCIe" device.
Rephrase the text in the kernel source where the word ordering is
wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/57da7c80-0e48-41b5-8427-884a02648f55@rowland.harvard.edu
The "buf" is skb->data that comes from the firmware. We want to print
"len" number of bytes. But there is a missing period so the "len"
variable is used for formatting (width) instead of limiting the output
(precision).
Fixes: cad2bd8a13 ("wifi: rtw89: support firmware log with formatted text")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/0700c7b9-bfd3-4aa6-82bf-5bf3c74644e1@moroto.mountain
Time Averaged SAR (TAS) tracks the amount of transmit power over a
period of time and adjusts the power accordingly. Two thresholds are
used to determine when to increase or reduce transmit power: Dynamic
Power Reduction (DPR) on/off. Compared to Static SAR, which has a
constant transmit power, TAS can improve the user experience or
range extension.
TAS can be enabled through BIOS, and the driver will evaluate
Realtek ACPI DSM with RTW89_ACPI_DSM_FUNC_TAS_EN to determine
whether TAS should be enabled.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230804053458.31492-1-pkshih@realtek.com
A few samples get bad performance on 2GHz band, so use proper IQK command
code and select another group to have wider range of calibration value.
Fixes: f2abe804e8 ("wifi: rtw89: 8852b: rfk: add IQK")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230803110150.8457-1-pkshih@realtek.com
RX full flags are raised if certain types of RX FIFO are full, and then
drop all following MPDU of AMPDU. In order to resume to receive MPDU
when RX FIFO becomes available, we clear the register bits by the
commit a0d99ebb3e ("wifi: rtw89: initialize DMA of CMAC"). But, 8852AE
needs more settings to support this. To quickly fix disconnection problem,
revert the behavior as before.
Fixes: a0d99ebb3e ("wifi: rtw89: initialize DMA of CMAC")
Reported-by: Damian B <bronecki.damian@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217710
Cc: <Stable@vger.kernel.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Damian B <bronecki.damian@gmail.com>
Link: https://lore.kernel.org/r/20230808005426.5327-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WiFi 7 chips doesn't have static const tables defined in driver. If tables
aren't loaded properly from firmware file, driver can get NULL pointer
access exception. One way is to add the checking statements when trying to
access these tables, but I choose to check them right after loading
firmware elements from firmware file, so I don't need to add error handlers
everywhere.
Currently, the needed firmware elements of WiFi 6 chips are all zero, and
coming WiFi 7 chip will need at least BB MCU, parameters of BB and RF.
We will add them after 8922AE is verified.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-9-pkshih@realtek.com
The tables of BB and RF parameters are pairs of {addr, value}. Load them
and convert from little-endian to CPU order, and show the version to clear
which version we are using.
rtw89_8922ae 0000:03:00.0: Firmware element BB version: 00 04 00 00
rtw89_8922ae 0000:03:00.0: Firmware element radio A version: 00 13 00 00
rtw89_8922ae 0000:03:00.0: Firmware element NCTL version: 00 05 00 00
We use tables defined in firmware elements with higher priority than
original static const tables defined in driver, because WiFi 7 chips will
not define the tables in driver, and existing chips can possibly migrate to
the new design one by one.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-8-pkshih@realtek.com
In order to pack more data into firmware file, we introduce firmware
elements and append BB_MCU firmware first. The first part of new firmware
file is still unchanged firmware of WiFi CPU, so the new firmware format
can be backward compatible to old format. The new elements part consists
of ID and size basically, which can append more elements simply. To avoid
unaligned access in certain platform and be easy to read, headers of all
elements start at 16-byte aligned address.
+===========================================+
| original firmware |
| +-------------+
| | padding |
+===========================================+
| elm ID 1 | elm size | other header data |
+----------+----------+ |
| |
+-------------------------------------------+
| content (variable length) |
| +-------------+
| | padding |
+===========================================+
| elm ID 2 | elm size | other header data |
+----------+----------+ |
| |
+-------------------------------------------+
| content (variable length) |
| +-----------------------+
| | (no padding for the last one)
+===================+
More detail of element header is shown below. The additional fields
'version' and 'element_priv[]' are meta data of elements, so that we can
know element version easily, and element_priv[] provide specific fields
for certain element, such as RF path index for RF parameter tables.
+===========================================+
| elm ID | elm size | version | rsvd0 |
+----------+----------+----------+----------+
| rsvd1/2 | element_priv[] |
+-------------------------------------------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-7-pkshih@realtek.com
For existing chips, firmware is only for WiFi CPU, but WiFi 7 chips add
new hardware component BB MCU that needs firmware as well. The firmwares of
BB MCU 0/1 are also downloaded via the same path like WiFi CPU firmware,
and use the same firmware header format, so add firmware suits to access
them commonly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-6-pkshih@realtek.com
A firmware with v1 format contains many sections to download. Add parser to
read section type, target address, length, checksum and so on, and then
download the section to WiFi CPU with proper location.
The additional dynamic header length named dynamic_hdr_len is used to
skip content of dynamic header containing compiler flags of firmware, which
can help to determine variant firmware build, but currently rtw89 only
use single one variant. So, just skip the content.
The layout of a WiFi CPU firmware with v1 format looks like:
+---------------------------------------+
| Header (12 words) |
+---------------------------------------+
| Section header 1 (4 words) |
| Section header 2 (4 words) |
| Section header 3 (4 words) |
| ... |
+---------------------------------------+
| Dynamic header (variable length) |
+---------------------------------------+
| Data used & pointed by section |
| ... |
+---------------------------------------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-5-pkshih@realtek.com
New firmware header is used by upcoming WiFi 7 chips to have more
information, so use common field w3[31:24] to determine header version,
and then use corresponding function to read firmware version and commit ID:
rtw89_8852be 0000:03:00.0: Firmware version 0.29.29.1 (799134c3), cmd version 1, type 5
rtw89_8852be 0000:03:00.0: Firmware version 0.29.29.1 (799134c3), cmd version 1, type 3
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-4-pkshih@realtek.com
Original firmware log which is sent via C2H message bloats
code size of firmware and is also length-limited. So we put
some common log into format file, and firmware could use a
log ID and some variables in C2H message to map a formatted
text via pre-designed rule.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-3-pkshih@realtek.com
Firmware log format is an element of multi-firmware file
and used for firmware to provide log with formatted text.
Driver needs to recognize it in advance if it exists.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-2-pkshih@realtek.com
The data rate from RX descriptor also uses hardware rate v1 for WiFi 7
chips. The rate code contains three parts -- mode, NSS and MCS. For
CCK/OFDM/HT rates, NSS/MCS parts are the same as before. VHT/HE/EHT rates
are changed and listed as below:
mode NSS MCS
V0 [8:7] [6:4] [3:0]
V1 [10:8] [7:5] [4:0]
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-11-pkshih@realtek.com
WiFi 7 chips have more rate mode (EHT), higher MCS and more bandwidth, so
define and use reserved bits to carry these information in C2H events.
Also, the SS/MCS encoded bits of VHT and HE are changed, so define V1 masks
for them.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-9-pkshih@realtek.com
RA (rate adaptive), a mechanism to select proper rate, is implemented in
firmware, and this report is used to tell driver TX rate it is currently
using. Use struct to access this report, and doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-8-pkshih@realtek.com
Firmware C2H events contain two-word header which can indicate category,
class, function and length of received events. Use struct to access them,
and doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-7-pkshih@realtek.com
H2C RA V1 command adds two words to support WiFi 7 chips, which can
possibly support up to 4SS rates. Because current chips have only 2SS
rates, leave the fields blank for now. The main changes are to set
extended bits of EHT mode and bandwidth -- add a bit for EHT mode; add a
bit to enumerate 320MHz channel bandwidth.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-6-pkshih@realtek.com
RA (rate adaptive) H2C command is used to tell firmware which rates can
be used for specified MAC ID. Basically, this commit doesn't change result.
Only change to set two 32-bit instead of continual 8-byte rate masks one
by one. Originally, we only set 5-byte masks, because existing WiFi 6
2SS chips only need 5-byte masks. Setting two 32-bit masks will be more
efficient and also can support coming WiFi 7 2SS chips containing more
rates.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-5-pkshih@realtek.com
Rate pattern is controlled by 'iw bitrates' to fix rate as desired, and
we extend to support v1 rate.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-4-pkshih@realtek.com
To support EHT rate, hardware rate v1 is introduced. The CCK and OFDM rates
are persistent. HT/VHT/HE rates use different rate code from original, and
add new code for EHT rates.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-3-pkshih@realtek.com
The coming WiFi 7 chip is 8922AE which uses different hardware rate and
register naming rule. Adding a chip_info::chip_gen field can help to
do things by generations accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-2-pkshih@realtek.com
When using compressed firmware, the early firmware load feature will fail.
In most cases, the only downside is that if a device has more than one
firmware version available, only the last one listed will be loaded.
In at least two cases, there is no firmware loaded, and the device fails
initialization. See https://github.com/lwfinger/rtw89/issues/259 and
https://bugzilla.opensuse.org/show_bug.cgi?id=1212808 for examples of
the failure.
When firmware_class.dyndbg=+p" added to the kernel boot parameters, the
following is found:
finger@localhost:~/rtw89>sudo dmesg -t | grep rtw89
firmware_class: __allocate_fw_priv: fw-rtw89/rtw8852b_fw-1.bin fw_priv=00000000638862fb
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/5.14.21-150500.53-default/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/5.14.21-150500.53-default/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: Direct firmware load for rtw89/rtw8852b_fw-1.bin failed with error -2
firmware_class: __free_fw_priv: fw-rtw89/rtw8852b_fw-1.bin fw_priv=00000000638862fb data=00000000307c30c7 size=0
firmware_class: __allocate_fw_priv: fw-rtw89/rtw8852b_fw.bin fw_priv=00000000638862fb
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/5.14.21-150500.53-default/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/5.14.21-150500.53-default/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: Direct firmware load for rtw89/rtw8852b_fw.bin failed with error -2
firmware_class: __free_fw_priv: fw-rtw89/rtw8852b_fw.bin fw_priv=00000000638862fb data=00000000307c30c7 size=0
rtw89_8852be 0000:02:00.0: failed to early request firmware: -2
firmware_class: __allocate_fw_priv: fw-rtw89/rtw8852b_fw.bin fw_priv=00000000638862fb
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/5.14.21-150500.53-default/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/5.14.21-150500.53-default/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/5.14.21-150500.53-default/rtw89/rtw8852b_fw.bin.xz failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw.bin.xz failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/5.14.21-150500.53-default/rtw89/rtw8852b_fw.bin.xz failed for no such file or directory.
rtw89_8852be 0000:02:00.0: Loading firmware from /lib/firmware/rtw89/rtw8852b_fw.bin.xz
rtw89_8852be 0000:02:00.0: f/w decompressing rtw89/rtw8852b_fw.bin
firmware_class: fw_set_page_data: fw-rtw89/rtw8852b_fw.bin fw_priv=00000000638862fb data=000000004ed6c2f7 size=1035232
rtw89_8852be 0000:02:00.0: Firmware version 0.27.32.1, cmd version 0, type 1
rtw89_8852be 0000:02:00.0: Firmware version 0.27.32.1, cmd version 0, type 3
The key is that firmware version 0.27.32.1 is loaded.
With this patch, the following is obtained:
firmware_class: __free_fw_priv: fw-rtw89/rtw8852b_fw.bin fw_priv=000000000849addc data=00000000fd3cabe2 size=1035232
firmware_class: fw_name_devm_release: fw_name-rtw89/rtw8852b_fw.bin devm-000000002d8c3343 released
firmware_class: __allocate_fw_priv: fw-rtw89/rtw8852b_fw-1.bin fw_priv=000000009e1a6364
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/6.4.3-1-default/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/6.4.3-1-default/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/6.4.3-1-default/rtw89/rtw8852b_fw-1.bin.zst failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw-1.bin.zst failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/6.4.3-1-default/rtw89/rtw8852b_fw-1.bin.zst failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/rtw89/rtw8852b_fw-1.bin.zst failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/6.4.3-1-default/rtw89/rtw8852b_fw-1.bin.xz failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw-1.bin.xz failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/6.4.3-1-default/rtw89/rtw8852b_fw-1.bin.xz failed for no such file or directory.
rtw89_8852be 0000:02:00.0: Loading firmware from /lib/firmware/rtw89/rtw8852b_fw-1.bin.xz
rtw89_8852be 0000:02:00.0: f/w decompressing rtw89/rtw8852b_fw-1.bin
firmware_class: fw_set_page_data: fw-rtw89/rtw8852b_fw-1.bin fw_priv=000000009e1a6364 data=00000000fd3cabe2 size=1184992
rtw89_8852be 0000:02:00.0: Loaded FW: rtw89/rtw8852b_fw-1.bin, sha256: 8539efc75f513f4585cf0cd6e79e6507da47fce87225f2d0de391a03aefe9ac8
rtw89_8852be 0000:02:00.0: loaded firmware rtw89/rtw8852b_fw-1.bin
rtw89_8852be 0000:02:00.0: Firmware version 0.29.29.1, cmd version 0, type 5
rtw89_8852be 0000:02:00.0: Firmware version 0.29.29.1, cmd version 0, type 3
Now, version 0.29.29.1 is loaded.
Fixes: ffde7f3476 ("wifi: rtw89: add firmware format version to backward compatible with older drivers")
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724183927.28553-1-Larry.Finger@lwfinger.net
If there is a failure during kstrtobool_from_user()
rtw89_debug_priv_btc_manual_set should return a negative error code
instead of returning the count directly.
Fix this bug by returning an error code instead of a count after
a failed call of the function "kstrtobool_from_user". Moreover
I omitted the label "out" with this source code correction.
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/tencent_1C09B99BD7DA9CAD18B00C8F0F050F540607@qq.com
If there is a failure during rtw89_fw_h2c_raw() rtw89_debug_priv_send_h2c
should return negative error code instead of a positive value count.
Fix this bug by returning correct error code.
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/tencent_AD09A61BC4DA92AD1EB0790F5C850E544D07@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A firmware contains basic header, sections and optional dynamic header.
Define them by a struct, so it will be easier to understand the layout,
and also simply access these elements.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616060601.28460-1-pkshih@realtek.com
Some old declarations about TX power stuffs were named with confusing
`_max`. But, they mean "the number of". So we change them to be named
with `_num`.
(No logic is changed.)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616060523.28396-1-pkshih@realtek.com
RTL8851B is a chip with only single RF path, and it must use 1 TX power
value for transmission, so force 1 TX power value to prevent hardware
logic gets wrong TX power values randomly in certain samples.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-6-pkshih@realtek.com
The main change is to adjust RX calibration groups from {0,1,2,3} to {0,2}
in 5 GHz, so reduce elements from 4 to 2, and use index to iterate them.
Meanwhile, always do RX narrowband calibration (ID_NBRXK) for each group.
NCTL is used to assist IQK, so also update NCTL to 0x6 along with internal
tag HALRF_029_00_103.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-5-pkshih@realtek.com
LCK is short for LC Tank calibration. To keep RF performance, do this
calibration if difference of thermal value is over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-4-pkshih@realtek.com
Update 8851B TX power tables to RF version R28.
TX power tables' changes:
* TX power limit and TX power shape:
update 5 GHz configurations for FCC and IC
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-3-pkshih@realtek.com
Drop useless '_iqk_track()' and 'rtw8852a_iqk_track()' (they
just change 'thermal_rek_en' field which is set but unused
and so removed as well) functions, set but unused 'kcount'
field of 'struct rtw89_iqk_info', and convert 'thermal' to
local variables where appropriate (it doesn't need to have
longer storage duration because it is actually used for the
debugging purposes only).
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230614081555.91395-2-dmantipov@yandex.ru
Remove a bunch of unused (and set but unused) fields
from 'struct rtw89_btc_wl_nhm', 'struct rtw89_dle_info',
'struct rtw89_hal' and 'struct rtw89_env_monitor_info'
driver-specific data structures, adjust related bits.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230614081555.91395-1-dmantipov@yandex.ru
Update TX power tables to RF version R63.
TX power tables' changes:
* TX power byrate:
tweak a bit
* TX power limit, TX power limit RU, TX power shape:
configure values for MEXICO, UKRAINE, CHILE, QATAR
tweak a bit on other configured values
* 6 GHz TX power limit, 6 GHz TX power limit RU:
add an extra dimension for 6 GHz regulatory power type, i.e.
STD (standard power), LPI (low power indoor), VLP (very low power)
Besides, we adjust TX power handling at 6 GHz in phy to consider 6 GHz
regulatory power type.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-8-pkshih@realtek.com
Update TX power tables to RF version R63.
TX power tables' changes:
* TX power byrate:
tweak a bit
* TX power limit, TX power limit RU, TX power shape:
configure values for MEXICO, UKRAINE, CHILE, QATAR
tweak a bit on other configured values
* 6 GHz TX power limit, 6 GHz TX power limit RU:
add an extra dimension for 6 GHz regulatory power type, i.e.
STD (standard power), LPI (low power indoor), VLP (very low power)
Besides, we adjust TX power handling at 6 GHz in phy to consider 6 GHz
regulatory power type.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-7-pkshih@realtek.com
Update TX power tables to RF version R63.
TX power tables' changes:
* TX power byrate:
tweak a bit
* TX power limit, TX power limit RU, TX power shape:
configure values for MEXICO, UKRAINE, CHILE, QATAR
tweak a bit on other configured values
* 6 GHz TX power limit, 6 GHz TX power limit RU:
add an extra dimension for 6 GHz regulatory power type, i.e.
STD (standard power), LPI (low power indoor), VLP (very low power)
Besides, we adjust TX power handling at 6 GHz in phy to consider 6 GHz
regulatory power type.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-6-pkshih@realtek.com
Configure the corresponding power type for 6 GHz regulatory if we can
determine one single target. Otherwise, we use the default one.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-5-pkshih@realtek.com
Update notes:
According to Realtek Regulatory R40 and Realtek Channel Plan R64,
configure rtw89_regulatory mapping of 6 GHz for more countries and
adjust rtw89_regulatory mapping of 2/5 GHz for a few countries.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-4-pkshih@realtek.com
We allow platform to disable 6 GHz on chips, which supports 6 GHz, through
BIOS. Driver will evaluate Realtek acpi DSM with RTW89_ACPI_DSM_FUNC_6G_DIS
(function 3) to get whether 6 GHz should be disabled.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-3-pkshih@realtek.com
We refine to check if supported bands of NL80211_BAND_2GHZ and
NL80211_BAND_5GHZ exist before freeing their iftype_data. For
now, it does not really encounter problems because all current
chips support both 2 GHz and 5 GHz. But, driver actually allows
chips to declare whether 2/5 GHz are supported or not. In case
some future chips really don't support them, we refine this code.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-2-pkshih@realtek.com
RTL8851B firmware supports CRASH_TRIGGER feature from v0.29.41.0.
After this is configured, debugfs fw_crash can support type 1 on
RTL8851B to trigger firmware crash and verify L2 recovery through
simulation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230531060713.57203-5-pkshih@realtek.com
The key condition to check in wrapper of setting TX power is whether entity
is active or not. Before entity is active, we restrict TX power from being
set by outside callers, e.g. SAR/regulatory.
We mark entity as inactive when powering off MAC. Then, we will mark it as
active when we initialize HW channel stuffs after MAC power on. Although we
can get an active entity after leaving idle phase, TX power doesn't be set
well for default channel until stack set target channel for connection. It
causes that RF things cannot use better TX power during this interval.
Below are some cases which may encounter this or a similar situation.
* hw scan process before connection
As described above.
* right after restart hardware process (SER L2)
HW stuffs of target channel is initialized after mac80211 restart
hardware, but we unexpectedly need to wait one more command to set
channel again or to set TX power.
To fix it and improve RF behavior in that interval, during setting channel,
we don't need to check entity state before setting TX power, which actually
is used to restrict outside callers. It means we call chip ops directly to
replace the wrapper call. Then, TX power can be initialized as long as we
initialize/setup HW stuffs on one channel.
Besides, all chips should configure ops of setting TX power, so we remove
trivial check on pointer.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230531060713.57203-4-pkshih@realtek.com
We now support RTL8851B which has only single RF path. For chip with
single RF path, TX power page is valid only in single path section.
So, we refine debugfs txpwr table to access TX power page according
to RF path number of runtime chip. It can prevent us from reading
beyond valid sections.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230531060713.57203-3-pkshih@realtek.com
This enables hw_scan for 8851b after firmware version 0.29.37.1.
Extend the channel info struct with padding zeros so newer firmware
can work properly, this change is backward compatible with older
firmware.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230531060713.57203-2-pkshih@realtek.com
There are a number of upcoming things in both the stack and
drivers that would otherwise conflict, so merge wireless to
wireless-next to be able to avoid those conflicts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Originally, add this check rule to prevent entering LPS if more than one
vif (in station mode) connect to AP. Since we have checked this by previous
commit, remove this redundant check.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527082939.11206-4-pkshih@realtek.com
This driver relies on IEEE80211_CONF_PS of hw->conf.flags to turn off PS or
turn on dynamic PS controlled by driver and firmware. Though this would be
incorrect, it did work before because the flag is always recalculated until
the commit 28977e790b ("wifi: mac80211: skip powersave recalc if driver SUPPORTS_DYNAMIC_PS")
is introduced by kernel 5.20 to skip to recalculate IEEE80211_CONF_PS
of hw->conf.flags if driver sets SUPPORTS_DYNAMIC_PS.
Correct this by doing recalculation while BSS_CHANGED_PS is changed and
interface is added or removed. For now, it is allowed to enter PS only if
single one station vif is working, and it could possible to have PS per
vif after firmware can support it. Without this fix, driver doesn't
enter PS anymore that causes higher power consumption.
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Cc: stable@vger.kernel.org # 6.1+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527082939.11206-3-pkshih@realtek.com
struct rtw89_btc_btf_tlv contains a one-byte member that is intended as a
flexible array:
In function 'fortify_memcpy_chk',
inlined from '_append_tdma' at drivers/net/wireless/realtek/rtw89/coex.c:1579:3:
include/linux/fortify-string.h:583:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
583 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Make this actually use a flexible array to let the compiler understand.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230523113241.2772811-1-arnd@kernel.org
There is a spelling mistake in a literal string. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522085924.913649-1-colin.i.king@gmail.com
The register-based H2C/C2H are used to exchange commands and events with
firmware. The exchange data is limited, but it is relatively simple,
because it can work before HCI initialization. To make these code clean,
use struct to access them. This patch doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-6-pkshih@realtek.com
RX descriptor is to provide basic and important information related to
packets, such as packet size, security, MAC ID and so on. Change to use
struct to access these fields, and not change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-5-pkshih@realtek.com
PHY status IEs generated by BB hardware is to provide more detail
information related to received packets, such as RSSI and bandwidth.
To avoid type casting, change buf type from u8* to void* as well.
This patch doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-4-pkshih@realtek.com
If received packet type is PPDU status, RX info provides information
attached by MAC hardware, and mention how long BB information attached.
This conversion patch doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-3-pkshih@realtek.com
The next generation chips use different RX descriptor format, so add
a chip_ops to hook suitable handlers. Also, the length of RX descriptor is
different, so add a variable to store the length according to chip and
descriptor content dynamically. Then, the code can be more general.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-2-pkshih@realtek.com
Since 8851BE is ready, so add 8851BE to Makefile and Kconfig. Currently,
it can support STA, AP and monitor modes with good performance.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-8-pkshih@realtek.com
8851B has the same issue: management frames get stuck when WiFi
chip enters low PS mode, so we also add notify wake function to
trigger WiFi chip wake before forwarding management frames.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-7-pkshih@realtek.com
The register ranges of upcoming chips are different from current, and even
existing chips have different ranges, so support longer length to dump
registers. Then, user space can decide the ranges according to chip.
Since arbitrary length (e.g. 7) would be a little complicated, so simply
make length a multiple of 16. The output looks like
18620000h : 8580801f 82828282 82828282 080800fd
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-6-pkshih@realtek.com
These configurations include path control, TX grant, TX scheduler,
register-based H2C/C2H and so on.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-4-pkshih@realtek.com
These capabilities include helpers of BT coexistence, RX PPDU status
parser, DIG (dynamic initial gain) and CFO (center frequency offset)
settings.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-3-pkshih@realtek.com
Get TX power value from tables according to selected country and channel,
and set proper power to registers.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-2-pkshih@realtek.com
H2C of packet offload needs to wait FW ACK by C2H. But, it's possible
that packet offload happens during SER (system error recovery), e.g.
SER L2 which restarts HW. More, packet offload flow isn't deferrable.
So, the H2C wait may get `ret == 1` (unreachable).
However, the logic FW deals with packet offload is simple enough, just
clone content. It means that as long as the H2C is issued successfully,
the thing will succeed sooner or later. Therefore, after we add a debug
log when receiving ACK to packet offload, it would be acceptable that
during SER, packet offload don't really wait for ACK. And, if debugging,
we can still check its debug logs. Besides, we can expect that if we see
SER before receiving ACK to packet offload, those debug logs of the ACK
have a time difference.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516082441.11154-4-pkshih@realtek.com
Some specific H2C (host to chip command) needs waiting until FW ACK by
C2H (chip to host event). However, during SER (system error recovery),
most interrupts are disabled, so we can't receive C2H immediately. It
causes this kind of H2C TX waits will always time out during SER.
To save time spent by SER, we don't do these redundant waits. And, to
make a difference from -ETIMEDOUT in other cases, we make the function
return 1 for SER case. When some H2C callers really catch `ret == 1` at
runtime, they can determine whether it's reasonable or not, and consider
how to resolve their flow if needed.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516082441.11154-3-pkshih@realtek.com
The total_sta_assoc and the tdls_peer are used for statistics accodring
to stations' information. L2 (Level 2) SER (system error recovery) will
call ieee80211_restart_hw() which re-invokes sta_state ops. And then,
the total_sta_assoc and tdls_peer will be re-increased. In case wrong
statistics results, we reset them in SER L2 handling.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516082441.11154-2-pkshih@realtek.com
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.
To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-4-pkshih@realtek.com
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-3-pkshih@realtek.com
RX DCK is receiver DC calibration. With this calibration, we have proper
DC offset to reflect correct received signal strength indicator. Do this
calibration when bringing up interface and going to run on AP channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-2-pkshih@realtek.com
Parse efuse content to recognize MAC address, RFE type, XTAL offset and
so on. And, parse offset of PHY capability to retrieve TX power
calibration data.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-7-pkshih@realtek.com
Set MAC/BB/RF registers according to channel we are going to set. In
additional, certain channels or bands need more deals, such as enable CCK
in 2 GHz band, spur elimination at certain frequencies.
The set channel helper is used to save/restore states before/after setting
channel, and does reset BB to prevent hardware getting stuck in abnormal
state during switching channel and receiving data.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-6-pkshih@realtek.com
Add basic functions to power on chip and enable and access BB/RF, as
well as reset and hardware settings of BB.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-5-pkshih@realtek.com
Add 8851B specific parameters of BT coexistence. Since 8851B has special
two antenna hardware module with antenna diversity, BT coexistence needs
to recognize this, so add some fields to store these information for
further use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-4-pkshih@realtek.com
Though 8851BE is a 1x1 chip, but it has two antenna hardware module that
needs additional configuration to help choose antenna we are going to use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-3-pkshih@realtek.com
8851B hardware version A and B use different firmware, but register version
code of these two are the same, so add this helper to read efuse version to
determine which version is installed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-2-pkshih@realtek.com
For 8852CE, there is abnormal state called CMDPSR_FRZTO,
which occasionally happens in some platforms, and could be
found by firmware and fixed in current SER flow, so we add
suppress function to avoid verbose message for this resolved case.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508084335.42953-4-pkshih@realtek.com
Newer FW re-design SER (syetem error recovery) L1 (level 1) flow.
New L1 flow will expect two extra states before original L1 flow.
* Before:
fw --- M1 --> driver
fw <-- M2 --- driver
fw --- M3 --> driver
fw <-- M4 --- driver
fw --- M5 --> driver
* After:
fw --- pre-M0 --> driver
fw <-- post-M0 --- driver
fw --- M1 --> driver
fw <-- M2 --- driver
fw --- M3 --> driver
fw <-- M4 --- driver
fw --- M5 --> driver
Then before M1, FW gets one more interval to deal with things that FW
should have handled well. To consider backward/forward compatibility,
FW and driver won't change flow from M1 to M5. (only except that halt
trigger control will change a little bit.) So, there will be two differnt
starting points of SER L1.
* old FW: SER L1 starts from M1
* new FW: SER L1 starts from pre-M0
Then, driver adds the new SER L1 entry and also keep the original one
instead of changing it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508084335.42953-3-pkshih@realtek.com
RTL8851B keeps almost the same interrupt flow as RTL8852A and RTL8852B.
But, it uses a different bitmask for interrupt indicator of FW HALT C2H.
So, we make a chip judgement in pci when configuring interrupt mask.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508084335.42953-2-pkshih@realtek.com
U-NII-4 band, i.e 5.9GHz channels, can be supported by chip 8852C, 8852B
and 8851B. But, it is not supported by chip 8852A. Flag support_unii4 is
added in chip info and defined by chip accordingly to indicate that.
We reference this flag of runtime chip to decide whether to register
5.9GHz channels.
After that, we consider if U-NII-4 band is allowed by our regulatory
rule of U-NII-4. If chip::support_unii4 but not regd::allow_unii4,
we stll do not register 5.9GHz channels.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508081211.38760-4-pkshih@realtek.com
For realtek regulatory, there are following two kinds of configurations
to determine whether to allow UNII-4 band, i.e. 5.9GHz channels.
1. default setting according to whether chip support it or not
2. evaluate realtek ACPI DSM with RTW89_ACPI_DSM_FUNC_59G_EN (func. 6)
If (1) is false, we won't try (2) and just disallow UNII-4. Otherwise,
if (2) is not supported or returns a non-specific value, we follow the
default setting either. Besides, this commit aims to add decision logic
in rtw89 regulatory. Actually, driver doesn't register UNII-4 yet. That
will be handled by another commit.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508081211.38760-3-pkshih@realtek.com
Introduce realtek ACPI DSM method to get required BIOS
configurations. It will be used in the following commits.
And, enum rtw89_acpi_dsm_func is added for listing the functions
which are currently recognized.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508081211.38760-2-pkshih@realtek.com
The if statement is reversed so it will not record the chip version.
This was detected using Smatch:
drivers/net/wireless/realtek/rtw89/core.c:3593 rtw89_read_chip_ver()
error: uninitialized symbol 'val'.
Fixes: a6fb2bb846 ("wifi: rtw89: read version of analog hardware")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/e4d912a2-37f8-4068-8861-7b9494ae731b@kili.mountain
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-6-pkshih@realtek.com
DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output good quality signals.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-5-pkshih@realtek.com
RCK is synchronize RC calibration. Driver triggers this calibration and
sets the result to register. This calibration is needed once when interface
is going to up.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-4-pkshih@realtek.com
Automatic amplitude control calibration (AACK) is the calibration to ensure
the oscillator is biased for a constant output amplitude. We do this
calibration if card does power on.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-3-pkshih@realtek.com
Add to set RF registers according to the channel we want to switch. The
callers will be added afterward.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-2-pkshih@realtek.com
Configure DLE (data link engine) memory size for operating modes.
Similarly, HFC standing for HCI flow control is used to set quota
according to operating modes, which are SCC or download firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-9-pkshih@realtek.com
Add WoWLAN stub to 8851B, and decalre this chip can support magic packet
and disconnect wakeup.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-8-pkshih@realtek.com
BA CAM of 8852C has more entries and more fields of H2C, and needs
initialization before using. Due to differences from 8852A/8852B, we name
it as V1 before. However, real V1 of BA CAM is introduced now, so change
it to V0_EXT to avoid confusing with firmware design.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-7-pkshih@realtek.com
Previously, 8852B has smaller FIFO size than others, so I use chip_id to
choose debug_mask before. 8851B has similar design, so add a field to
chip_info as a general expression.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-6-pkshih@realtek.com
Since CFO XTAL registers of 8851B is different from 8852A, add a chip_info
field to define their difference. Other chips use another interface, so
fill NULL to this field.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-5-pkshih@realtek.com
NCTL (nano-controller) is used to assist RF calibration that sends
commands to NCTL so it can reduce IO from driver. 8851B needs additional
settings, so add a table to do things.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-4-pkshih@realtek.com
Add PCI entry to 8851BE with its device ID 10ec:b851, also fill PCI info
according to its capabilities.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-3-pkshih@realtek.com
8851B is a 1x1 80 MHz bandwidth chip working on 2/5 GHz. Add these basic
information, and more settings will be added by functions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-2-pkshih@realtek.com
The following are scan offload related H2C (host to chip) function types.
* H2C_FUNC_ADD_SCANOFLD_CH
* H2C_FUNC_SCANOFLD
Before doing FW scan, we will continuously send multiple H2Cs with above
types which are used to tell FW the scan configuration of this time. But,
if FW doesn't handle one of these H2Cs well, the FW scan process might
not run as expected and driver should notice it early.
So, this commits makes scan offload related H2Cs wait for FW done ACK via
rtw89_wait_for_cond() and rtw89_complete_cond(). And, we check the return
code of these H2Cs from FW.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/a15f4bd594f71d7602ea67698b035805143700c9.camel@realtek.com
We have some MAC H2Cs (host to chip packets), which have no clear
individual C2Hs (chip to host packets) to indicate FW execution
response, but they are going to require to wait for FW completion.
So, we have to deal with this via common MAC C2H receive/done ACKs.
This commit changes the context, where common MAC C2H receive/done
ACK handlers are executed, to interrupt context. And, code comments
are added to prevent future commits from using it incorrectly.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/c4d766885e00b9f9dcf7954a80096c8b9d21149b.camel@realtek.com
The H2Cs (host to chip packets) related to packet offload functions
need to wait for FW responses in case FW state machine gets wrong
and makes driver status no longer able to align FW one. In flow,
driver may continuously send multiple H2Cs of packet offload series.
If somehow FW doesn't deal with the former yet but the latter has
gotten in, it might cause the problem mentioned above.
So, we block these H2Cs by rtw89_wait_for_cond(). And then, when
the corresponding C2Hs (chip to host packets) is received, we call
rtw89_complete_cond(). Besides, RTW89_MAC_C2H_FUNC_PKT_OFLD_RSP's
C2H handler should be executed in interrupt context to make our
wait/complete process work as expected.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/9ae8c1f105901c65e3171276a9fd6c99ae51803f.camel@realtek.com
There are two places where offload packets of 6 GHz probe would be deleted
from FW, i.e. calling rtw89_fw_h2c_del_pkt_offload().
* rtw89_core_cancel_6ghz_probe_tx()
* rtw89_release_pkt_list()
It is possible that we try to delete the same one from FW twice. Although
it might not be a big problem for now, it will depend on the runtime chip
firmware. So, we add a check to avoid it. In case things becomes complex
due to racing problem, we don't choose to do list_del(info->list) and
kfree(info) in both sides.
Besides, rtw89_fw_h2c_del_pkt_offload() will needs to wait for completion
after the follow-up commit. However, rtw89_core_cancel_6ghz_probe_tx()
was called in interrupt context. So, we move the stuffs of calling
rtw89_fw_h2c_del_pkt_offload() from rtw89_core_cancel_6ghz_probe_tx()
into a work. Then, we also need a check there before we call it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/091966e5709cd7caecf9b81f7fd6388ae2b70a7e.camel@realtek.com
We have a pair of FW functions, rtw89_fw_h2c_add_pkt_offload() and
rtw89_fw_h2c_del_pkt_offload(). The rtw89_fw_h2c_add_pkt_offload()
acquires the bit itself, but the bit needs to be released by the
caller of rtw89_fw_h2c_del_pkt_offload(). This looks asymmetrical
and is not friendly to callers.
Second, if callers always releases the bits, it might make driver
unaligned to bitmap status of FW after some failures of calling
rtw89_fw_h2c_del_pkt_offload(). So, this commit move bit release
into rtw89_fw_h2c_del_pkt_offload().
In general, driver will call rtw89_fw_h2c_add_pkt_offload() and
rtw89_fw_h2c_del_pkt_offload(), and then, SW bitmap can align
with FW one. There is one exception when notify_fw is false.
It happens when driver detects FW problems and is going to
reset FW. Only in this case, driver needs to release bits
outside rtw89_fw_h2c_del_pkt_offload().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/8cf5d45c5b04e7b680d4eb9dda62056cdce14cec.camel@realtek.com
Take EVM into consideration when doing antenna diversity, and the priority
is higher than RSSI. Since EVM is more relevant to performance than RSSI,
especially in OTA environment.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418012820.5139-8-pkshih@realtek.com
RSSI statistics are grouped by CCK, OFDM or non-legacy rate. These
statistics will be collected in training state for both (main/aux)
antenna. There is a time period (ANTDIV_DELAY) for rate adaptive
settle down before start collect statistics when switch antenna.
Antenna diversity checks packet count from training state for each
group and use the most one as the final RSSI for comparison, and
then choose the better one as target antenna.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418012820.5139-7-pkshih@realtek.com
Initialize basic antenna switch settings according to hardware module
design, and set to default antenna A. The set antenna function will be
called dynamically to switch antenna according to EVM and RSSI.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418012820.5139-6-pkshih@realtek.com
To help debug performance problem, add EVM and SNR statistics to debugfs
that shows
EVM: [(26.75, 26.75) (25.75, 25.75)] SNR: 40
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418012820.5139-5-pkshih@realtek.com
RSSI strength is only from PHY path A, but there are two antenna for the
module which supports antenna diversity. So, set RSSI value to index 1 of
RSSI array if current antenna is on antenna B. Then, debugfs can show
two RSSI values with a asterisk mark on selected antenna.
RSSI: -23 dBm (raw=174, prev=173) [-26, -23*]
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418012820.5139-4-pkshih@realtek.com
TX antenna diversity is a mechanism to select a proper antenna from two
antenna for single one hardware PHY chip. It chooses antenna with better
EVM or RSSI, and use GPIO to control SPDT to switch selected antenna.
RFE type from efuse is used to define if a module can support TX antenna
diversity when (type % 3) is 2.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418012820.5139-3-pkshih@realtek.com
To be more clear to know where it gets information from PHY IE0 data,
change to use struct and standard le32_get_bits() to access. This doesn't
change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418012820.5139-2-pkshih@realtek.com
The function to request DLE (data link engine) buffer uses 'u16' as return
value that mixes error code, so change it to 'int' as regular error code.
Also, treat invalid register value (0xfff) as an error.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414082228.30766-1-pkshih@realtek.com
Add iface_combination declaration to enable concurrent mode. Only two
interfaces under same frequency is supported currently. We limit the
role combination to be STA + P2P or STA + AP only for now until new
feature is requested.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415035016.15788-2-pkshih@realtek.com
Power saving for more than one station is not supported currently.
Disallow entering PS mode when we have more than one associated
stations.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415035016.15788-1-pkshih@realtek.com
Since firmware can't have proper statistics, driver update the
statistics periodically to firmware to assist in tuning performance.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415034900.15679-5-pkshih@realtek.com
Remove macros that set H2C data. Instead, use struct and
le32_encode_bits() with mask definition to make it clean.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415034900.15679-4-pkshih@realtek.com
Since we can get the current channel definition each interface maps to,
remove store_op function that is no longer required to make things simple.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415034900.15679-3-pkshih@realtek.com
Mac80211 core may ask driver to change to idle mode during HW scan,
then H2C command for HW scan will send failed since chip is in idle
mode. Therefore, We check the SCANNING flag before entering IPS to
prevent this behavior.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415034900.15679-2-pkshih@realtek.com
8851B has various hardware module types, so BT coexistence in firmware
needs these information to make decision. Add them to make 8851B work
well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230412012831.10519-5-pkshih@realtek.com
Correct Bluetooth RSSI count method. The 6dB is the gap between hardware
packet sampled value and real RSSI value.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230412012831.10519-4-pkshih@realtek.com
Chips use similar hardware for path control, but could different
path/antenna configuration. Add these register to monitor, if there are
wrong settings, these register can help to debug.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230412012831.10519-3-pkshih@realtek.com
When Wi-Fi & Bluetooth are both busy at the same time, Wi-Fi need to
enable RX gain to protect Wi-Fi RX RF ability. Without this configure
the interference from Bluetooth will bring a big impact to Wi-Fi RX.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230412012831.10519-2-pkshih@realtek.com
In WoWLAN Mode, it's expected that WiFi chip could enter power save mode
only after all setting is finished, but current wow_enter_lps function
break the rule and may lead to WoWLAN function fail in low probability,
so fix it.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230410053438.10682-2-pkshih@realtek.com
To support WoWLAN mode for 8852be, we add one PLE quota setting and
WoWLAN stub, which shows that supported WLAN events include receiving
magic packet, rekey packet and deauth packet, and disconnecting from AP.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230410053438.10682-1-pkshih@realtek.com
Use primary channel index to determine which 5 MHz mask should be enable.
This mask is used to prevent noise from channel edge to effect CCA
threshold in wide bandwidth (>= 40 MHZ).
Fixes: 1b00e9236a ("rtw89: 8852c: add set channel of BB part")
Fixes: 6b0698984e ("wifi: rtw89: 8852b: add chip_ops::set_channel")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230406072841.8308-1-pkshih@realtek.com
These tables contain BB and RF parameters that driver will load them into
registers. It also contains TX power according to country, band, rate and
so on. Increasing thermal can cause TX power degraded, so power tracking
tables are defined to compensate TX power.
Internal version of these tables:
- HALBB_029_106_15 (V17)
- HALRF_029_00_089
* Radio A 0x22
* NCTL 0x5
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230401142548.55466-3-pkshih@realtek.com
These tables contain BB and RF parameters that driver will load them into
registers. It also contains TX power according to country, band, rate and
so on. Increasing thermal can cause TX power degraded, so power tracking
tables are defined to compensate TX power.
Internal version of these tables:
- HALBB_029_106_15 (V17)
- HALRF_029_00_089
* Radio A 0x22
* NCTL 0x5
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230401142548.55466-2-pkshih@realtek.com
Many settings of 8851B are the same as 8852B or 8852A, like DLE (Data link
engine), security engine and so on. Update them according to hardware
design.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330133324.19538-4-pkshih@realtek.com
For two RF paths chips, we normally set path B as main path by default.
8851B has single one RF path, so set TX path to A and set mapping of
path B to 0.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330133324.19538-3-pkshih@realtek.com
The chip contains digital and analog parts, and each of them has its own
version number. This is used by BT coexistence mechanism to make strategy
decision for different analog version.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330133324.19538-2-pkshih@realtek.com
Turn on hardware CFO (central frequency offset) compensation based on IC
capability, and improve digital CFO compensation accuracy by using
more fixed points number.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330132352.13647-1-pkshih@realtek.com
One chip can have different RFE (RF front end) types which we will judge
at runtime. And, different RFE types may use different RF parameter tables.
Though we didn't really meet this case previously, we are going to meet it
on upcoming chip RTL8851B. So, this commit handles parameter tables for
runtime RFE type.
We now encapsulate rtw89_txpwr_rule_<2/5/6>ghz tables into rtw89_rfe_parms.
Then, each chip defines its default parameter tables, and if needed, it can
configure extra parameter tables by RFE type. Finally we determine runtime
parameter tables by RFE type if one is configured. Otherwise, we use the
default parameter tables.
For now, we just move all settings under default parameter tables. We will
configure parameter tables by RFE types in separate commits afterwards.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330080331.37155-1-pkshih@realtek.com
In the discuss threads [1] [2], new firmware format break user space
because older drivers can't recognize new firmware format. To avoid this,
the new format will be named rtw89/rtw8852b_fw-1.bin and only new driver
try to load it. Old drivers only load original and understandable firmware
rtw89/rtw8852b_fw.bin.
More, new driver will be still backward compatible with old firmware, so
original firmware can be used by new driver.
If there is newer firmware format is introduced, rtw89/rtw8852b_fw-2.bin
will be given. The same rules will be applied like above. So, we will have
firmware like below in linux-firmware in the future.
rtw89/rtw8852b_fw-2.bin
rtw89/rtw8852b_fw-1.bin
rtw89/rtw8852b_fw.bin
After this patch, MODULE_FIRMWARE() of 8852A/B/C become
rtw89/rtw8852a_fw.bin
rtw89/rtw8852b_fw-1.bin
rtw89/rtw8852c_fw.bin
[1] https://lore.kernel.org/linux-wireless/df1ce994-3368-a57e-7078-8bdcccf4a1fd@gmail.com/T/#m24cb43be31a762d0ea70bf07f27ae96c59f6931b
[2] https://bugzilla.kernel.org/show_bug.cgi?id=217207
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320130606.20777-4-pkshih@realtek.com
Since we are going to load more than one firmware and some are not
presented or optional, using asynchronous API request_firmware_nowait()
will become complicated. Also, we want to use firmware_request_nowarn()
to avoid warning messages when loading optional files. So, use
schedule_work to be simpler.
To abstract loading a firmware or file, define a struct rtw89_fw_req_info
containing a struct firmware and a completion to ensure this firmware is
loaded completely.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320130606.20777-3-pkshih@realtek.com
In early feature bitmap obtained from rtw89_early_fw_feature_recognize(),
the bits needed to check get increased. It's more friendly to work with
RTW89_CHK_FW_FEATURE(). So, we concentrate the flow of iterating FW feature
configures and calling RTW89_SET_FW_FEATURE() for various uses. And then,
we adjust rtw89_early_fw_feature_recognize() for RTW89_CHK_FW_FEATURE().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320130606.20777-2-pkshih@realtek.com
We used to store operating channel info after associated. However, scan
might happen before that. Without switching back to operating channel,
authentication or association might fail. Therefore, we switch back to
operating channel when the scanning vif's BSSID is non-zero, which
implies connected or during attempt to connect.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-6-pkshih@realtek.com
Use POWER_ON flag to make sure power on/off is symmetric. Since both
remain_on_channel and hw_scan both alter the power state, this makes
sure that we don't enter/leave IPS mode twice.
Also, replace IPS related functions with inline function that does
similar logic so we can track it more easily.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-5-pkshih@realtek.com
Add support of remain on channel ops. Since channel context is
required to enable multi-channel concurrent(MCC) and the current
ROC in mac80211 don't support more than 1 channel context, add this
to let P2P and other protocols relying on this work as expected.
The off-channel duration and cancel timing is purely controlled by
upper layers.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-4-pkshih@realtek.com
Allocate a per-skb completion to track those skbs we are interested in
and wait for them to complete transmission with TX status.
Normally, the completion object is freed by wait side, but it could be
timeout result that complete side should free the object instead. Add a
owner field with RCU to determine which side should free the object.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-3-pkshih@realtek.com
Adding this supports beacon filter and connection quality monitor.
To make host CPU wake up less, let firmware perform signal
monitoring and beacon processing, then notify driver upon signal
changes or beacon loss.
This feature needs firmware 0.27.56 or newer to support it.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-2-pkshih@realtek.com
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230323112613.7550-5-cai.huoqing@linux.dev
Need to configure EDCCA threshold to default value before scan, and recall
original value after scan to prevent probe request can't be sent out.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230322060238.43922-1-pkshih@realtek.com
We use ppdu_sts to obtain channel information from hardware, to ensure
that the scan results have correct channel information. However, some of
ppdu_sts that is filtered by the to_self check is also needed for the scan
results. Therefore, we modify the filter part in front of CFO count.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320093112.30466-3-pkshih@realtek.com
We find that when starting WoWLAN, the second join_info H2C is
unnecessary and leads WoWLAN not enter power save mode if using new
firmware, so remove it.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320093112.30466-2-pkshih@realtek.com
By default the driver uses the 1M and 6M rate (0x0) for data frames in
2 GHz and 5/6 GHz bands respectively. But the rate that might not AP
supported. Therefore, We modify the data lowest rate according to the
lowest of AP supported rate.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320093112.30466-1-pkshih@realtek.com
The register-based H2C/C2H are used to exchange information between driver
and firmware, but only apply to narrow area because its data size is
smaller than regular packet-based H2C/C2H.
This kind of H2C/C2H must be paired. To identify if any H2C/C2H is missing,
update counters to help diagnose this kind of problems.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230316063956.71687-1-pkshih@realtek.com
Update driver with the supported firmware version of the below item.
Bluetooth firmware BT_Coex_Ver: 0x07
Wi-Fi firmware version:
RTL8852C->v0.27.56.10
RTL8852A->v0.24.36
RTL8852B->v0.29.29
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230314020617.28193-6-pkshih@realtek.com
In order to reduce firmware code size cost, remove some counter value from
the structure. But firmware didn't update version code. To parse the
correct report, add another variation version v105 to parse it.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230314020617.28193-5-pkshih@realtek.com
The LNA gain didn't set before, it will lead some WiFi RX issue.
And the setting can increase both of WiFi & BT performance while
they are both RX.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230314020617.28193-4-pkshih@realtek.com
If driver enable firmware report during WiFi power saving, the
firmware timer will lead to some power saving issue like,
fail to enter LPS, can not leave LPS or some unexpected issue.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230314020617.28193-3-pkshih@realtek.com
This LPS state will not turn off RF, and it can still do some basic
traffic, only RTL8852B has the state. Coexistence need let Bluetooth
know WiFi is still alive to prevent some Bluetooth performance issue.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230314020617.28193-2-pkshih@realtek.com
To support v5 version firmware cycle report, apply the related structure
and functions. v5 cycle report add a group of status to show how the
free-run/TDMA training goes to. It is a firmware mechanism that can auto
adjust coexistence mode between TDMA and free run mechanism at 3 antenna
solution. v5 version provide more reference data to let the mechanism
make decision.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230308053225.24377-8-pkshih@realtek.com
Compare to v1 and v2 removed some not usable parameters. Save firmware
code size. The information can show how frequent and how long the
Bluetooth scan do. It will help to debug coexistence issue.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230308053225.24377-7-pkshih@realtek.com
Correct pointer assignment of v1 null data report. It doesn't really
change logic at all, but it looks more readable.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230308053225.24377-6-pkshih@realtek.com
The v2 firmware report reduce its maximum register numbers from 30 to 20,
it can help to save firmware code size.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230308053225.24377-5-pkshih@realtek.com
There is a new mechanism which can do some real time performance
tuning for WiFi and BT. This TX/RX info is a condition provide to
firmware to do traffic analysis.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230308053225.24377-4-pkshih@realtek.com
Remove WiFi traffic busy level & traffic rate from active role information.
This information will move to v5 version TDMA cycle info.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230308053225.24377-3-pkshih@realtek.com
The error map and counter can help to analyze is coexistence mechanism
going well or not. For example, if there is E2G (External control Wi-Fi
slot for Wi-Fi 2.4 GHz) hang counter, it means Wi-Fi firmware didn't cut
a slot for Wi-Fi 2.4 GHz. Maybe something wrong with firmware timer.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230308053225.24377-2-pkshih@realtek.com
Originally, we keep RX standby timer to handle beamformee CSI, but this
spends power and causes system not entering power save mode. To improve
power consumption, release the timer if throughput becomes low.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230307141848.26403-1-pkshih@realtek.com
When SER L1 triggered, driver need to stop Rx and clear RTW89_FLAG_RUNNING
flag. If track_work check RTW89_FLAG_RUNNING simultaneously, it will check
failed and never queue track_work again, and LPS won't enter either.
Therefore, we cancel delayed work when enter SER L1, and queue delayed work
when leave SER L1.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230224082117.21241-1-pkshih@realtek.com
The newer chips use the newer firmware branches, e.g. v027, v029.
And, those firmware branches are supposed to support packet drop
when they are just branched out.
The initial firmware branch used by each chip is as below.
* 8852A: v009
* 8852C: v027
* 8852B: v027
So, only 8852A may use firmware which doesn't support packet drop at
runtime. To save trivial positive listing in firmware feature table,
we change to reverse judgment.
Besides, rtw89_mac_ptk_drop_by_band_and_wait() missed to check firmware
feature before calling rtw89_fw_h2c_pkt_drop(). We also fix it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230220070202.29868-7-pkshih@realtek.com
To obtain correct packet frequency for hw_scan, 52b needs to decode
the channel index obtained from hardware. Change the driver related
set channel part as well to make driver/firmware compatible.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230220070202.29868-5-pkshih@realtek.com
Since the range of channel table is identical among ICs. Make channel
encode/decode function common and not IC dependent. So all ICs with
matching firmware that needs this kind of coding can use it directly.
This patch doesn't change logic at all.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230220070202.29868-4-pkshih@realtek.com
RTL8852B firmware supports CRASH_TRIGGER feature from v0.29.29.0.
After this is configured, debugfs fw_crash can support type 1 on
RTL8852B to trigger firmware crash and verify L2 recovery through
simulation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230220070202.29868-3-pkshih@realtek.com
8852B has the same issue: management frames get stuck when wifi
chip enters low ps mode, so we alse add notify wake function to
trigger wifi chip wake before forwarding management frames.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230220070202.29868-2-pkshih@realtek.com
Since 6 GHz band has around 60 channels and more strict rules for
active probing. Reduced neighbor report can be used to reduce the
channels we scan and get specific target BSS info to probe for.
Declare flag WIPHY_FLAG_SPLIT_SCAN_6GHZ so the scan request could be
divided into two portions: legacy bands and 6 GHz bands. So RNR
information from legacy bands could later be used when 6 GHz scan.
When the scan flag NL80211_SCAN_FLAG_COLOCATED_6GHZ is set, cfg80211
will pass down a reduced channel set which contains PSCs and non-PSC
with RNR info received in the 2 GHz/5 GHz band. This reduces the
scan duration by allowing us to only scan for channels in which APs
are currently operating.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230217120007.8835-1-pkshih@realtek.com
For some ICs, packets can't be sent correctly without initializing
CMAC table first. Previous flow do this initialization after
associated, results in authentication response fails to transmit.
Move the initialization up front to a proper place to solve this.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230216082807.22285-1-pkshih@realtek.com
The H2C of del_pkt_offload must be called before polling FW status
ready, otherwise the following downloading normal FW will fail.
Fixes: 5c12bb66b7 ("wifi: rtw89: refine packet offload flow")
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230214114314.5268-1-pkshih@realtek.com
For normal (successful) flow, it must return 0. The original code uses
'return ret', and then we need to backward reference to initial value to
know 'ret = 0'. Changing them to 'return 0', because it will be more
readable and intuitive. This patch doesn't change logic at all.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202302101023.ctlih5q0-lkp@intel.com/
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230213091328.25481-1-pkshih@realtek.com
Previously, all supported chips had two RF paths. Therefore, these
codes used static number for TX power setting. Now, we are planning
to support a new chip which has only one RF path. So, we refine the
setting codes to refer to chip's RF path number at runtime.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230203065157.8227-1-pkshih@realtek.com
For a packet with 1SS rate, it can also transmit via 2 antenna, called
2T mode. For 2T TX power offset, mask should be 2T as well. Fortunately,
the mask of 2T and 1T are the same, so it can still work well without
this fix.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230203064907.8046-1-pkshih@realtek.com
In path of setting channel and setting TX power, the rtw89_chan instance
to be used is controlled by top and passed down. The set_tx_shape_dfir()
is in path of setting TX power, so it should use the passed rtw89_chan
instead of querying it itself. Otherwise, it might encounter mismatch
between parameters if multi-channel.
For example,
rtw89_8852ce 0000:04:00.0: set tx shape dfir by unknown ch: 155 on 2GHz
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230201032057.7349-1-pkshih@realtek.com
Enable CLKREQ to reduce power consumption for 8852BE.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230126112715.5811-1-pkshih@realtek.com
New firmware type NORMAL_CE is introduced to support P2P-PS and hardware
scan, but no LPS-PG mode. After this patch, old firmware with NORMAL type
can still work well.
The use of this new type is the same as before, so we add new type to
avoid taking wrong firmware. Then, driver log can also give clear
information about this change:
rtw89_8852be 0000:03:00.0: Firmware version 0.29.26.0, cmd version 0, type 5
rtw89_8852be 0000:03:00.0: Firmware version 0.29.26.0, cmd version 0, type 3
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230123065401.14174-7-pkshih@realtek.com
Due to firmware size limit of 8852b, LPS-PG mode isn't supported after
0.29.26.0, and then we have more space to support other features, such as
P2P-PS, hardware scan and so on.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230123065401.14174-6-pkshih@realtek.com
For different firmware type, it could use different IDMEM mode, so reset
it to default to avoid encountering error during we bisect firmware
version, like
rtw89_8852be 0000:03:00.0: Firmware version 0.29.26.0, cmd version 0, type 5
rtw89_8852be 0000:03:00.0: Firmware version 0.29.26.0, cmd version 0, type 3
rtw89_8852be 0000:03:00.0: fw security fail
rtw89_8852be 0000:03:00.0: download firmware fail
rtw89_8852be 0000:03:00.0: [ERR]fwdl 0x1E0 = 0x62
rtw89_8852be 0000:03:00.0: [ERR]fwdl 0x83F2 = 0x8
rtw89_8852be 0000:03:00.0: [ERR]fw PC = 0xb8931154
rtw89_8852be 0000:03:00.0: [ERR]fw PC = 0xb8931154
rtw89_8852be 0000:03:00.0: [ERR]fw PC = 0xb8931150
rtw89_8852be 0000:03:00.0: [ERR]fw PC = 0xb8931154
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230123065401.14174-5-pkshih@realtek.com
Driver can prepare pkt_list for firmware that only uses them to send out
the packets in specific situations. To understand the usage of current
status, and to check if there is leakage problem, dump bitmap and the
indices used by certain function.
An example looks like:
map:
...
pkt_ofld: 3f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ...
[SCAN 0]: 3
[SCAN 1]: 4
[SCAN 3]: 5
VIF [0] xx:xx:xx:xx:xx:xx
...
pkt_ofld[GENERAL]: 0 1 2
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230123065401.14174-4-pkshih@realtek.com
For upcoming firmware, driver needs to do packet offload to firmware to
ensure LPS protocol work properly, so we update current connection and
disconnect flow to maintain packet offload flow, and integrate with
current WoWLAN flow which also needs packet offload.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230123065401.14174-3-pkshih@realtek.com
When driver fails to send H2C to firmware for pkt-offload, we should not
update the pkt_list of driver, and need to release allocated pkt index to
avoid wrong mapping between driver and firmware.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230123065401.14174-2-pkshih@realtek.com
Buffer STA on TDLS links are not currently supported. Therefore, it
is not allowed to enter the PS mode after TDLS link is established.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230119064631.66971-1-pkshih@realtek.com
To debug channel concurrency more centrally, we add a new debug flag,
RTW89_DBG_CHAN, for channel related things, especially channel concurrency.
Then, we change MCC (multi-channel concurrency) C2H (chip to host packets)
debug flag to it.
Besides, refine debug logs to show TSF in u64 directly.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230119064342.65391-2-pkshih@realtek.com
A 8-byte offset is missed during parsing C2Hs (chip to host packets)
of MCC (multi-channel concurrent) series.
So, we fix it.
Fixes: ef9dff4cb4 ("wifi: rtw89: mac: process MCC related C2H")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230119064342.65391-1-pkshih@realtek.com
RXI300 is a HW design to maintain stuffs across BUS, e.g. AXI, AHB, APB.
It will feedback an error when host does an invalid BUS operation.
For example,
* BUS master request without power/clock on.
* host reads/writes/accesses an invalid address.
They might lead to problems such as BUS timeout, platform hang, etc. So,
once if RXI300 feedback an error, it notifies that driver need a L2 SER
(system error recovery) to reset things.
Previously, driver did not parse the error scenario for RXI300. We add
it and assign a corresponding error code which will make SER flow do L2
reset.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230119063529.61563-3-pkshih@realtek.com
Only 8852C chip has valid pages on RTW89_DBG_SEL_MAC_30. To other chips,
this section is an address hole. It will lead to crash if trying to access
this section on chips except for 8852C. So, we avoid that.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230119063529.61563-2-pkshih@realtek.com
Add mac function rtw89_mac_port_get_tsf() to get TSF by port.
It will be used when MCC (multi-channel concurrency) calculates
timing things.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230119062453.58341-4-pkshih@realtek.com
Originally, rtw89_mac_port_tsf_sync() contains randomization logic
internally. However, not all situation, we need the randomization.
So, split out the generic part from it. And, make the full logic of
original one contained in rtw89_mac_port_tsf_sync_rand(). It will
still be used by its original caller as before. Then, the generic
one will be used in MCC (multi-channel concurrency) management flow.
MCC will implement its logic to decide the offset for TSF sync.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230119062453.58341-3-pkshih@realtek.com
Strictly speaking, the unit of the offset should be TU instead of ms.
So, correct it and the macro for calculation. Then, to make the macro
generic, the factor n is moved outside.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230119062453.58341-2-pkshih@realtek.com
Should update the driver with the supported firmware version of the
below item.
Bluetooth firmware BT_Coex_Ver: 0x07
Wi-Fi firmware version: RTL8852C->v0.27.56.10, RTL8852A->v0.24.36
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230117114109.4298-9-pkshih@realtek.com
The origin code will enable TDMA WL:BT = 50:50 to prevent Wi-Fi
throughput suddenly drop to 0 in the moment while A2DP pause.
And this protection just a short moment, and will turn to Bluetooth
idle case when A2DP turn into sniff mode. But the raspberryPI simulated
A2DP device will not turn into sniff mode. So the protection will bring
the throughput drop.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230117114109.4298-8-pkshih@realtek.com
When Wi-Fi enter and leave LPS, coexistence driver need to know
is there A2DP exist or not. And when Wi-Fi sleep in deep power save
state will not able to receive mailbox sent from Bluetooth. So update
the A2DP exist information from reading register.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230117114109.4298-7-pkshih@realtek.com
When Wi-Fi is RX, set Bluetooth background scan to low-priority and
not to break Wi-Fi packet. Bluetooth can RX depend on hardware ability
even RX request has been rejected. This way can improve Wi-Fi RX
throughput performance.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230117114109.4298-6-pkshih@realtek.com
Adjust the log format and correct variable reference to make the log
more readable.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230117114109.4298-5-pkshih@realtek.com
Force firmware to update TDMA parameter when enter/exit power saving.
The TDMA instant feature will make firmware force update TDMA parameter
immediately when the TDMA parameter H2C to firmware. Without this feature,
it will have a low fail rate trigger Bluetooth audio sound glitch when
Wi-Fi is under power saving. Or Wi-Fi fail to turn in to power save state.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230117114109.4298-4-pkshih@realtek.com
Reset the counter no matter Wi-Fi is notified turning into power save or
not. With rest the counter coexistence will recognize Bluetooth is hanged
easily.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230117114109.4298-3-pkshih@realtek.com
This patch update the external control (Wi-Fi firmware control) type of
TDMA related parameters, almost all of these case were related to Wi-Fi
multi-role situations & AP mode.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230117114109.4298-2-pkshih@realtek.com
The configurations, wde_qempty_acq_num and wde_qempty_mgq_sel, are used
when MAC checks if TX queues are empty. Fill the corresponding setting
for 8852B.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-5-pkshih@realtek.com
TX BD's RAM table describes how HW allocates usable buffer section
for each TX channel at fetch time. The total RAM size for TX BD is
chip-dependent. For 8852BE, it has only half size (32) for TX channels
of single band. Original table arrange total size (64) for dual band.
It will overflow on 8852BE circuit and cause section conflicts between
different TX channels.
So, we do the changes below.
* add another table for single band chip and export both kind of tables
* point to the expected one in rtw89_pci_info by chip
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-4-pkshih@realtek.com
Some hardware modules don't have good RF characteristic as regular.
It could get ADC abnormal in low temperature, and it causes bad RX
performance and affects calibration result of DPK.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-3-pkshih@realtek.com
This change fixes the precision of CFO and TX EVM, and it could imporve
performance in some cases. Also, use the correctted definition for 8852A.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-2-pkshih@realtek.com
The mac_id of management frames should follow rtwvif->mac_id or
rtwsta->mac_id. Add this patch to set the correct mac_id and
prevent unexpected behavior.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106121517.19841-2-pkshih@realtek.com
When transmitting a packet that gets from ieee80211_nullfunc_get(),
the vif in tx_info->control was no assigned, which will cause
dereferencing a null pointer.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106121517.19841-1-pkshih@realtek.com
The Wi-Fi role info structure will need to H2C to firmware, firmware
need these information to do some multi-role operation. v1 add DBCC
and NOA information in the structure. And driver side also need to
put/get values at the corresponding version of structure.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-8-pkshih@realtek.com
RTL8852B support the new features like TDMA instant (Change TDMA mechanism
immediately), Co-RX feature (Wi-Fi/Bluetooth can RX in the same time) and
so on. The v1 TDMA policy will enable those newer mechanism. It will have
a better coexistence performance.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-7-pkshih@realtek.com
Because the difference of the hardware design, RTL8852C can not get the
PTA owner by the same method with RTL8852B, RTL8852A. Modify the get owner
API and related logic.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-6-pkshih@realtek.com
Slot list is to list the WiFi/Bluetooth PTA hardware priority setting.
Move the list parser to its function, not to append together with TDMA
parser.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-5-pkshih@realtek.com
The report records the slots/events and their time cost about the code
call flow at firmware, ver 3 assign a reserved variable to recognize
the report is enabled or not. And add corresponding function to parsing
the report.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-4-pkshih@realtek.com
Coexistence need to send Null data to stop AP keeps TX packet to DUT
before DUT coexistence switch to Bluetooth time slot, or it will be an
interference to DUT BT and because DUT will not RX packet from AP
the packet retry may harmful to WL TP. Compare to v1 version, the newer
firmware report will also report Null TX data counter.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-3-pkshih@realtek.com
The newer Wi-Fi firmware are all changed to "Not to send H2C to
mention firmware how many call flow step should firmware trace".
The structure had removed the member, and define the steps number
at newer version firmware.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-2-pkshih@realtek.com
Add check for the return value of alloc_workqueue since it may return
NULL pointer.
Moreover, add destroy_workqueue when rtw89_load_firmware fails.
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230104142901.1611-1-jiasheng@iscas.ac.cn
Do `kfree_skb(new)` before `goto out` to prevent potential leak.
Fixes: 8959077797 ("rtw89: 8852a: add ieee80211_ops::hw_scan")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103141054.17372-1-pkshih@realtek.com
Change style to feature version separate. And because there are
different WiFi roles number in the firmware, it will make structure
length longer or shorter, so update the length calculator to cover
the difference.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-8-pkshih@realtek.com
Only when firmware control report version is 1, need to get the counter by
reading the register. The other version will monitor the counter at
firmware. And upstream branch only RTL8852A has this old version.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-7-pkshih@realtek.com
Comparing v5 control report to v4 version, v5 reduce some of variable's
size to reduce firmware code size. And change the grant signal report
format.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-6-pkshih@realtek.com
The rtw89 driver may support more than 1 version of Wi-Fi firmware for
certain chips. In order to support all the firmware, change to select logic
by firmware feature version code. Type control version 4 will monitor
Bluetooth PTA hardware counters at firmware and C2H to driver, but
version 1 will not do this.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-5-pkshih@realtek.com
To support v4 version firmware cycle report, apply the related
structure and functions. v4 cycle report add a group of status
to show how the free-run/TDMA training goes to. It is a firmware
mechanism that can auto adjust coexistence mode between TDMA and
free run mechanism at 3 antenna solution.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-4-pkshih@realtek.com
Because there are new report format in the upcoming patches, to make the
logic more readable, rename the related structure by their version number.
And to support the several version at the same time, add union definition
to include all the versions.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-3-pkshih@realtek.com
There are at least 2 version of cycle report format. If the code keep
translating the report to local variable, the numbers of variable in
check btc report function will out of maximum variable numbers. And
most of these variable are using only one time, it is not necessary
to store at memory.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-2-pkshih@realtek.com
Some hardware modules don't have good RF characteristic as regular.
It could have RF PA characteristic that current code doesn't handle
properly, and it runs into wrong DPK flow that doesn't complete DPK
resulting in bad EVM.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221216052939.9991-1-pkshih@realtek.com
Reduce dwell time to improve scan duration in 6 GHz. This is required
for scan requests that does not include RNR parsing and does full
channel scan.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221214091952.42792-1-pkshih@realtek.com
BSS color mapping register is different per IC, therefore, move this
register to chip_info and update the setting function. Without this patch,
wrong BSS color causes behavior abnormal, especially DL-OFDMA.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221214091803.41293-1-pkshih@realtek.com
In order to make different version of TDMA and coming update in the future
can all work well, use BTC format version to replace chip_id, because
format could change for specific chip_id.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221217141745.43291-8-pkshih@realtek.com
Change the checking logic to switch case. Make the code more readable.
There are more feature including to common code, in order to commit the
following version of the features, switch case will make the logic more
clearly. This patch did not change logic.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221217141745.43291-7-pkshih@realtek.com
Wi-Fi firmware update AFH report feature to version 2. If there is BT BLE
device connect to DUT, the mechanism will send H2C to request BT BLE
channel map, it will help to debug.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221217141745.43291-6-pkshih@realtek.com
The different version use different bit definition to enable firmware
report. WiFi firmware will report information from Bluetooth firmware or
some Wi-Fi firmware mechanism/status to driver by these bits. To solve the
difference, add a function to map bitmap and versions.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221217141745.43291-5-pkshih@realtek.com
Ask WiFi firmware to send Bluetooth version report when we want to show
Bluetooth debug info. If there is no request for debug log, driver will
not enable the report. This modification can save some C2H/H2C resources.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221217141745.43291-4-pkshih@realtek.com
Previous patch has added format version derived from firmware version.
Use the format version, and remove constant version number from chip_info.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221217141745.43291-3-pkshih@realtek.com
Originally, each chip maintains its own format version followed firmware
it uses. As new chip is added, firmware changes format of exchange
messages to have rich information to handle more conditions.
When old chip is going to upgrade firmware, it could use new format and
driver needs to maintain compatibility with old firmware. So, add this
version array to achieve this goal.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221217141745.43291-2-pkshih@realtek.com
RX DCK stands for RX DC calibration that affects CCA, so abnormal
calibration values resulted from calibration failure can cause TX get
stuck.
To solve this, redo calibration if result is bad (over thresholds). When
retry count is over, do recovery that sets high gain fields of RX DCK
results from low gain fields.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221209020940.9573-4-pkshih@realtek.com
Some DPK settings are wrong, and causes bad TX performance occasionally.
So, fix them by internal suggestions.
Fixes: da4cea16cb ("rtw89: 8852c: rfk: add DPK")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221209020940.9573-3-pkshih@realtek.com
After filling calibration parameters, set BIT(0) to enable the hardware
circuit, but original set incorrect bit that affects a little TX
performance.
Fixes: 76599a8d0b ("rtw89: 8852c: rfk: add DACK")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221209020940.9573-2-pkshih@realtek.com
Normally, system image should ensure firmware integrity, but we provide
an advance feature to ensure this by security section along with firmware.
To enable this feature, custom ID is programmed into efuse, and driver
will download proper security section to firmware.
Since I don't have this kind hardware modules on hand yet, but new format
is used by newer firmware. Therefore, I prepare this patch in advance to
consider size of security section as a factor of checking rule of firmware
size, but don't actually download security section to firmware.
This patch is backward compatible, so it will be safe to have this change
before adding an new format firmware to linux-firmware repository.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221209012215.7342-1-pkshih@realtek.com
ER (Extended Range) SU is to have a larger coverage. We set this as a RA
capability, and then firmware can choose ER SU to transmit packets to
reception at cell edge. For 8852C, it needs to fill this capability in
TXWD, so update rtw89_build_txwd_info0_v1().
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221209012110.7242-1-pkshih@realtek.com
To support multiple vifs, fw need more information of each role.
Send this info to make things work as expected.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202061527.505668-5-pkshih@realtek.com
Remove according vifs from list if we couldn't set this interface up.
Otherwise the rtwvif_list could contain unreferenced objects.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202061527.505668-4-pkshih@realtek.com
Disable hardware beacon related functions when ap stops. So hardware won't
transmit beacons while interface is already removed.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202061527.505668-3-pkshih@realtek.com
If the interface is in AP/P2P GO mode, we adjust the TSF with random
offset to avoid TBTT of different vifs to overlap and collide.
For every new interface added, we adjust the value and resync for all
interfaces.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202061527.505668-2-pkshih@realtek.com
Under some condition, we now have to do early request full firmware when
rtw89_early_fw_feature_recognize(). In this case, we can avoid requesting
full firmware twice during probing driver. So, we pass out full firmware
from rtw89_early_fw_feature_recognize() if it's requested successfully.
And then, if firmware is settled, we have no need to request full firmware
again during normal initizating flow.
Setting firmware flow is updated to be as the following.
platform | early recognizing | normally initizating
-----------------------------------------------------------------------
deny reading | request full FW | (no more FW requesting)
partial file | | (obtain FW from early pahse)
-----------------------------------------------------------------------
able to read | request partial FW | async request full FW
partial file | (quite small chunk) |
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202060521.501512-3-pkshih@realtek.com
Kernel logs on platform enabling SECURITY_LOADPIN_ENFORCE
------
```
LoadPin: firmware old-api-denied obj=<unknown> pid=810 cmdline="modprobe -q -- rtw89_8852ce"
rtw89_8852ce 0000:01:00.0: loading /lib/firmware/rtw89/rtw8852c_fw.bin failed with error -1
rtw89_8852ce 0000:01:00.0: Direct firmware load for rtw89/rtw8852c_fw.bin failed with error -1
rtw89_8852ce 0000:01:00.0: failed to early request firmware: -1
```
Trace
------
```
request_partial_firmware_into_buf()
> _request_firmware()
>> fw_get_filesystem_firmware()
>>> kernel_read_file_from_path_initns()
>>>> kernel_read_file()
>>>>> security_kernel_read_file()
// It will iterate enabled LSMs' hooks for kernel_read_file.
// With loadpin, it hooks loadpin_read_file.
```
If SECURITY_LOADPIN_ENFORCE is enabled, doing kernel_read_file() on partial
files will be denied and return -EPERM (-1). Then, the outer API based on it,
e.g. request_partial_firmware_into_buf(), will get the error.
In the case, we cannot get the firmware stuffs right, even though there might
be no error other than a permission issue on reading a partial file. So we have
to request full firmware if SECURITY_LOADPIN_ENFORCE is enabled. It makes us
still have a chance to do early firmware work on this kind of platforms.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202060521.501512-2-pkshih@realtek.com
First, introduce struct rtw89_sub_entity for chanctx related stuffs.
Second, add enum rtw89_sub_entity_idx to rtw89_vif for vif operation
to access its/right chanctx stuffs after future multi-channel support.
Besides, RTW89_SUB_ENTITY_0 is the default chanctx entry throughout
driver, i.e. it's used for things which may not have a target chanctx
yet. So, we need to ensure that RTW89_SUB_ENTITY_0 is always working.
If there is at least one alive chanctx, then one of them must take
RTW89_SUB_ENTITY_0. If no alive chanctx, RTW89_SUB_ENTITY_0 will be
filled by rtw89_config_default_chandef().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221129083130.45708-7-pkshih@realtek.com
These MCC H2C(s) require to wait for MCC C2H to determine if the
execution is successful. Through rtw89_wait_for_cond(), we make
them wait for either a completion with data from MCC C2H handlers,
which calls rtw89_complete_cond(), or timeout.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221129083130.45708-6-pkshih@realtek.com
Process C2H(s) related to MCC (multi-channel concurrency). These handling,
which either call rtw89_complete_cond() or show message in debug mode, can
be considered atomic/lock-free. So, they should be safe to be processed
directly after C2H pre-check in previous patch.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221129083130.45708-5-pkshih@realtek.com
MCC (multi-channel concurrency) related H2Cs (host to chip commands)
require to wait for C2H (chip to host events) responses to judge the
execution result and data. We introduce helpers to assist this process.
Besides, we would like the helpers to be generic for use in driver even
outside of MCC H2C/C2H, so we make a independent patch for them.
In the following, I describe the things first.
```
(A) C2H is generated by FW, and then transferred upto driver. Hence,
driver cannot get it immediately without a bit waitting/blocking.
For this, we choose to use wait_for_completion_*() instead of
busy polling.
(B) From the driver management perspective, a scenario, e.g. MCC,
may have mulitple kind of H2C functions requiring this process
to wait for corresponding C2Hs. But, the driver management flow
uses mutex to protect each behavior. So, one scenario triggers
one H2C function at one time. To avoid rampant instances of
struct completion for each H2C function, we choose to use one
struct completion with one condition flag for one scenario.
(C) C2Hs, which H2Cs will be waitting for, cannot be ordered with
driver management flow, i.e. cannot enqueue work to the same
ordered workqueue and cannot lock by the same mutex, to prevent
H2C side from getting no C2H responses. So, those C2Hs are parsed
in interrupt context directly as done in previous commit.
(D) Following (C), the above underline H2Cs and C2Hs will be handled
in different contexts without sync. So, we use atomic_cmpxchg()
to compare and change the condition in atomic.
```
So, we introduce struct rtw89_wait_info which combines struct completion
and atomic_t. Then, the below are the descriptions for helper functions.
* rtw89_wait_for_cond() to wait for a completion based on a condition.
* rtw89_complete_cond() to complete a given condition and carry data.
Each rtw89_wait_info instance independently determines the meaning of
its waitting conditions. But, RTW89_WAIT_COND_IDLE (UINT_MAX) is reserved.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221129083130.45708-4-pkshih@realtek.com
Before queuing C2H work, we check atomicity of the C2H's handler first now.
If atomic or lock-free, handle it directly; otherwise, handle it with mutex
in work as previous. This prepares for MAC MCC C2Hs which require to be
processed directly. And, their handlers will be functions which can be
considered atomic.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221129083130.45708-3-pkshih@realtek.com
The `rtw89_mcc_info mcc` is only for RFK MCC stuffs instead of common
MCC management info. Replace it with `rtw89_rfk_mcc_info rfk_mcc` to
avoid confusion and reserve `struct rtw89_mcc_info mcc` for MCC management
code.
(No logic changes.)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221129083130.45708-2-pkshih@realtek.com
PoP stands for Packet on Packet that can improve performance in noisy
environment, but it could get RX stuck suddenly. In normal mode, firmware
can help to resolve the stuck, but firmware doesn't work in monitor mode.
Therefore, turn off PoP to avoid RX stuck.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221125072416.94752-4-pkshih@realtek.com
With basic HE radiotap, we can check data rate in sniffer data. To store
the radiotap data, we reserve headroom of aligned 64 bytes, and then
update HE radiotap in monitor mode, so it doesn't affect performance in
normal mode.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221125072416.94752-3-pkshih@realtek.com
For running with mac80211 channel context ops and using only as monitor,
we need to enable WANT_MONITOR_VIF to let mac80211 process virtual monitor
interface. Then, we are able to set channel on the monitor from user space.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221125072416.94752-2-pkshih@realtek.com
The index RTW89_PHYSTS_BITMAP_NUM is not a valid physts IE page.
So, fix the check condition.
Fixes: eb4e52b3f3 ("rtw89: fix incorrect channel info during scan")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221118042322.26794-1-pkshih@realtek.com
During doing change_interface(), hardware is power-off, so some components
are inaccessible and return error. This causes things unexpected, and we
don't have a warning message for that. So, ignore some IO operations in
this situation, and add a warning message to indicate something wrong.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117085235.53777-1-pkshih@realtek.com
There are some registers for transmit waveform control, two of them used
in this change are for BANDEDGE and TX_SHAPE control. BANDEDGE controls
whether to apply band edge filter to transmit waveform. TX_SHAPE controls
whether to apply triangular mask to transmit waveform. It is found for
some chip, these two should be turned off during OFDMA UL traffic for
better performance.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117063001.42967-3-pkshih@realtek.com
Add macro to get FD(frequency domain) CFO field from ie_type 1, and correct
the naming for preamble CFO field. Each IC could assign the CFO source to
either FD CFO or preamble CFO in chip_info. Based on the suggestion from HW
designer, rtw8852b and its derived versions will have better CFO tracking
performance with FD CFO.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117063001.42967-2-pkshih@realtek.com
When coexistence mechanism is under free-run mode, it could adjust WiFi
and BT TX power to avoid interference with each other. For other cases,
it should keep original TX power from regular predefined tables, so
set correct values to 255 for these cases.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117061832.42057-1-pkshih@realtek.com
8852B has smaller TX FIFO than others in WiFi chip, so it would be buffer
full frequently, but it doesn't affect TX performance. However, it shows
verbose debug messages with RTW89_DBG_UNEXP mask that is used to indicate
abnormal behavior, so change debug mask to RTW89_DBG_TXRX for 8852B.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221108014230.11068-1-pkshih@realtek.com
Coverity reported shift 16 bits could cause sign extension and might get
an unexpected value. Since the input values are predefined and no this
kind of case, original code is safe so far. But, still changing them to
use u32_encode_bits() will be more clear and prevent mistakes in the
future.
The original message of Coverity is:
Suspicious implicit sign extension: "max_cfg->cma0_dma" with type "u16"
(16 bits, unsigned) is promoted in "max_cfg->cma0_dma << 16" to type
"int" (32 bits, signed), then sign-extended to type "unsigned long"
(64 bits, unsigned). If "max_cfg->cma0_dma << 16" is greater than
0x7FFFFFFF, the upper bits of the result will all be 1."
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1527095 ("Integer handling issues")
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221108013858.10806-1-pkshih@realtek.com
To detect TX or RX stuck, we implement SER (system error recovery) in
firmware to recover abnormal states of hardware, and report events to
driver. This kind of events could happen rarely per day.
SER might be true-positive or false-negative cases, and it could be failed
to recover true-positive case. We dump related registers to kernel message
at that moment and collect them from users, because they occur rarely,
randomly and hard to make sure we reproduce the same symptom. To address
problems accurately, add more registers by this patch.
It also might be false-positive cases that looks like TX or RX get stuck,
we need to dump registers from debugfs manually, so also add similar
things to debugfs as well.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221102014300.14091-3-pkshih@realtek.com
Dispatch is a component to decide packets forward to host, DMAC or
HAXIDMA. It contains CDT standing for CPU dispatcher, HDT standing
for host dispatcher, WDE standing for descriptor engine and PLE standing
for payload engine. STF is one kind of modes, it can be used if packet
send to hardware and doesn't need release report.
These debug port information can help to clarify the reason if
packets stuck in dispatch.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221102014300.14091-2-pkshih@realtek.com
Pattern match is an option of WoWLAN to allow the device to be woken up
from suspend mode when receiving packets matched user-designed patterns.
The patterns are written into hardware via WoWLAN firmware in suspend
flow if users have set up them. If packets matched designed pattern are
received, WoWLAN firmware will send an interrupt and then wake up the
device.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-8-pkshih@realtek.com
WoWLAN is a feature which allows devices to be woken up from suspend
state through WLAN events.
When user enables WoWLAN feature and then let the device enter suspend
state, WoWLAN firmware will be loaded by the driver and periodically
monitors WiFi packets. Power consumption of WiFi chip will be reduced
in this state.
We now implement WoWLAN function in rtw8852ae and rtw8852ce chip.
Currently supported WLAN events include receiving magic packet,
rekey packet and deauth packet, and disconnecting from AP.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-7-pkshih@realtek.com
In this patch we define some H2C, which will be called during suspend
flow, to enable WoWLAN function provided by WoWLAN firmware.
These H2C includes keep alive used to send null packet to AP periodically
to avoid being disconnected by AP, disconnect detection used to configure
how we check if AP is offline, wake up control used to decide which WiFi
events could trigger resume flow, and global control used to enable WoWLAN
function.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-6-pkshih@realtek.com
When entering WoWLAN mode, we need to drop all transmit packets,
including those in mac buffer, to avoid memory leakage, so implement
the drop_tx function.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-5-pkshih@realtek.com
PLE RX quota, which is the setting of RX buffer, is needed to be adjusted
dynamically for WoWLAN mode, and restored when back to normal mode.
The action is not needed for rtw8852c chip.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-4-pkshih@realtek.com
For WoWLAN mode, we need to download WoWLAN firmware by calling
fw_download(). Another, to disable/enable WiFi CPU is needed before
calling fw_download. Since Firmware runs on WiFi CPU, it is intuitive
to combine enable_cpu/disable_cpu functions into fw_download.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-3-pkshih@realtek.com
For WoWLAN mode, we only collect and send RF parameters to Firmware
without writing RF registers. So we add one function to practice it.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-2-pkshih@realtek.com
Add boundary check of mac_id when adding sta under AP/TDLS.
And, return -ENOSPC if the acquired mac_id is invalid.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221021091828.40157-1-pkshih@realtek.com
In order to debug performance issue intuitively, add bandwidth information
into debugfs entry phy_info. After applying this patch, it looks like:
TX rate [0]: HE 2SS MCS-11 GI:0.8 BW:80 (hw_rate=0x19b) ==> agg_wait=1 (3500)
RX rate [0]: HE 2SS MCS-9 GI:0.8 BW:80 (hw_rate=0x199)
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221021091601.39884-1-pkshih@realtek.com
They are just default declarations and we won't modify them directly.
Instead, we actually do moification on their memdup now. So, they
should be declared with const.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221020052702.33988-1-pkshih@realtek.com
Since firmware size is limited, we create variant firmwares for variant
application areas. To help driver to know firmware's capabilities, firmware
dynamic header is introduced to have more information, such as firmware
features and firmware compile flags.
Since this driver rtw89 only uses single one specific firmware at runtime,
this patch is just to ignore this dynamic header, not actually use the
content.
This patch can be backward compatible, and no this kind of firmware is
added to linux-firmware yet, so I can prepare this in advance.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221020052549.33783-1-pkshih@realtek.com
Now, basic materials for 8852be are ready, so add 8852be to Kconfig and
Makefile. Current version can support STA, AP and monitor modes.
We still fine tune some features, such as BT coexistence, performance, and
power consumption.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221014060237.29050-5-pkshih@realtek.com
The C2H class 2 function 3 is to report retry count of low rate, but driver
doesn't implement yet, so add a dummy case to avoid message:
rtw89_8852be 0000:03:00.0: c2h class 2 not support
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221014060237.29050-4-pkshih@realtek.com
Since RF calibrations are added, add chip_ops to call them. These chip_ops
include initial, full calibration, configuration when switching band and
scanning, and track work in period of 2 seconds.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221014060237.29050-3-pkshih@realtek.com
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221014060237.29050-2-pkshih@realtek.com
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.
To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-6-pkshih@realtek.com
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-5-pkshih@realtek.com
RX DCK is receiver DC calibration. With this calibration, we have proper
DC offset to reflect correct received signal strength indicator. Do this
calibration when bringing up interface and going to run on AP channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-4-pkshih@realtek.com
RCK is synchronize RC calibration. Driver triggers this calibration and
sets the result to register. This calibration is needed once when interface
is going to up.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-3-pkshih@realtek.com
DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output good quality signals.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-2-pkshih@realtek.com
Add 8852b specific constant tables and basic attributes containing
common chip_ops, firmware name, supported TX/RX NSS, number of CAM,
coexistence version, control register set, and so on.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-10-pkshih@realtek.com
When we are going to do RF calibrations, they need BB helpers to control
TX PLCP, power, path and mode. Also, it they need helpers to backup and
restore some registers before and after RF calibrations. Then, use flow of
RF calibrations will be like backup registers, configure calibration,
configure TX parameters, measure calibration result, and finally restore
registers.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-9-pkshih@realtek.com
To support variant models, such as 1x1 or 1T2R, we need this chip_ops to
change the path accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-8-pkshih@realtek.com
These chip_ops are used to assist BT coexistence module to control chip
specific operations, such as initial, pre-AGC, BT grant, set wifi priority
and tx power, RX gain, and get BT counter.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-6-pkshih@realtek.com
Thermal value reflects temperature that will affect RF performance, so
we re-calibrate RF characteristics if delta of thermal over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-5-pkshih@realtek.com
chip_ops::bb_reset is to reset baseband state after loading parameters,
because its state could be unpredictable at that moment. The other is
chip_ops::bb_sethw that is to set some baseband settings not including in
parameter tables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-4-pkshih@realtek.com
We need power on function to enable hardware circuits of MAC/BB/RF, and
then download firmware and load PHY parameters. After more settings, it
starts to work. When it enters idle, use power off function to have the
lowest power consumption.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-3-pkshih@realtek.com
This chip_ops is to assist set_channel, because we need setup and restore
hardware before and after set_channel.
Before set_channel, we stop transmitting, reset PPDU status, disable TSSI,
and disable ADC. After set_channel, do opposite things in reverse order.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-2-pkshih@realtek.com
Set channel in driver side to configure Tx power and channel index
correctly after scan. Before this, beacons with bandwidth larger than
20M bandwidth will be dropped by mac80211 due to frequency mismatch.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221007045900.10823-2-pkshih@realtek.com
Change active scan behavior to fit 6GHz requirements. There are many
different rules on active scan between 6GHz and 2GHz/5GHz, so if the
SSID is not specified, do fast passive scanning and limit number of
probe requests we send for now until new firmware can support all
rules.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221007045900.10823-1-pkshih@realtek.com
set_channel is main function to configure channel and bandwidth for all
layers, namely MAC, BB and RF. Additionally, MAC layer enables CCK rate
checking to avoid wrong rate from driver. BB layer configures SCO
(Sample Clock Offset) for CCK, TX gain error/offset, and reset baseband
hardware circuit after all configurations done.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-7-pkshih@realtek.com
The gain tables use different domain index, so we need to convert the index
from subband of chandef. Since these conversion functions can share with
8852b, make generic functions for further use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-6-pkshih@realtek.com
HFC is short for HCI flow control. These arrays are used to set quota
according to operating modes, which are SCC or download firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-5-pkshih@realtek.com
Before loading RF NCTL table, we need to configure IQK/DPK clock and reset
them, and then polling NCTL state ready. Since 8852BE needs additional
one setting, add it by this patch. Also, give them proper names.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-4-pkshih@realtek.com
Without this fix, some non-self packets are used to count CFO (center
frequency offset), and average CFO has unstable variation. Then, it causes
unexpected performance.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-3-pkshih@realtek.com
This chunk is to set fixed BT LNA2 at level5 when WiFi/BT shared BTG RFC
to improve BT anti-interference ability from adjacent channel. Since all
chips use the same setting, remove chip_ops::btc_bt_aci_imp.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-2-pkshih@realtek.com
By accident, the previous patch duplicated the initialization
of the wake_tx_queue callback. Fix that by removing the new
initializations.
Fixes: a790cc3a4f ("wifi: mac80211: add wake_tx_queue callback to drivers")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 is fully switching over to the internal TX queue (iTXQ)
implementation. Update all drivers not yet providing the now mandatory
wake_tx_queue() callback.
As an side effect the netdev interfaces of all updated drivers will
switch to the noqueue qdisc.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[add staging drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
MAC maintains TX FIFO to transmit packets with meta data to BB layer. To
debug abnormal transmission, we need to dump the content to dig problem.
Since FIFO of 8852C locates on different address with different size and
need additional switch to enable read operation, this patch adds the
changes accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220930134417.10282-2-pkshih@realtek.com
8852CE is a combo chip, and WiFi driver controls pin MUX. To output BT
firmware log to specific hardware pin, set pin MUX to achieve.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220930134417.10282-1-pkshih@realtek.com
The new BB parameters add new cfg_tpe 4 to improve performance of eFEM
modules (rfe_type >= 50), but we are using iFEM modules for now, so this
warning can be ignored.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220930133659.7789-2-pkshih@realtek.com
Using mdelay() can work well, but calibration causes too much time. Use
proper udelay() to get shorter time and the same result.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220930133318.6335-2-pkshih@realtek.com
IQK can change the values of this register set, so need to backup and
restore the values. During we rewrite IQK, the policy is changed. Some
values are controlled and filled by IQK, and don't need to restore after
IQK. Therefore, remove this kind of registers from this array.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220930133318.6335-1-pkshih@realtek.com
8852BE has two variants with different ID. One is 10ec:b852 that is a main
model with 2x2 antenna, and the other is 10ec:b85b that is a 1x1 model.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220928084336.34981-10-pkshih@realtek.com
This efuse region is to store PHY calibration, and it is a separated region
from the region that stores MAC address. Then, use these data to configure
via chip_ops::power_trim that is a calibration mechanism of TX power.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220928084336.34981-9-pkshih@realtek.com
efuse stores individual data about a chip itself, such as MAC address,
country code, RF and crystal calibration data, and so on. Define a struct
to help access efuse content, and copy them into a common struct.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220928084336.34981-8-pkshih@realtek.com
This chip_ops is to set TX power according to country, channel, rate and
so on. Since shared code is used to configure TX power, we only implement
specific part in this patch.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220928084336.34981-7-pkshih@realtek.com
Previously, value of each field is just shown as unsigned.
Now, we start to show them with sign to make things more intuitive
during debugging.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220928084336.34981-6-pkshih@realtek.com
Previously, we thought control registers or setting things for TX power
series may change according to chip. So, setting functions are implemented
chip by chip. However, until now, the functions keep the same among chips,
at least 8852A, 8852C, and 8852B. There is a sufficient number of chips to
share generic setting functions. So, we now remake them including TX power
by rate, TX power offset, TX power limit, and TX power limit RU as generic
ones in phy.c.
Besides, there are some code refinements in the generic ones, but almost
all of the logic doesn't change.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220928084336.34981-5-pkshih@realtek.com
These tables contain BB and RF parameters that driver will load them into
registers. It also contains TX power according to country, band, rate and
so on. Increasing thermal can cause TX power degraded, so power tracking
tables are defined to compensate TX power.
Internal version of these tables:
- HALRF_029_00_014 (R32)
- HALBB_027_046_05
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220928084336.34981-3-pkshih@realtek.com
These tables contain BB and RF parameters that driver will load them into
registers. It also contains TX power according to country, band, rate and
so on. Increasing thermal can cause TX power degraded, so power tracking
tables are defined to compensate TX power.
Internal version of these tables:
- HALRF_029_00_014 (R32)
- HALBB_027_046_05
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220928084336.34981-2-pkshih@realtek.com
Few stack changes and lots of driver changes in this round. brcmfmac
has more activity as usual and it gets new hardware support. ath11k
improves WCN6750 support and also other smaller features. And of
course changes all over.
Note: in early September wireless tree was merged to wireless-next to
avoid some conflicts with mac80211 patches, this shouldn't cause any
problems but wanted to mention anyway.
Major changes:
mac80211
* refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO)
feature continues
brcmfmac
* support CYW43439 SDIO chipset
* support BCM4378 on Apple platforms
* support CYW89459 PCIe chipset
rtw89
* more work to get rtw8852c supported
* P2P support
* support for enabling and disabling MSDU aggregation via nl80211
mt76
* tx status reporting improvements
ath11k
* cold boot calibration support on WCN6750
* Target Wake Time (TWT) debugfs support for STA interface
* support to connect to a non-transmit MBSSID AP profile
* enable remain-on-channel support on WCN6750
* implement SRAM dump debugfs interface
* enable threaded NAPI on all hardware
* WoW support for WCN6750
* support to provide transmit power from firmware via nl80211
* support to get power save duration for each client
* spectral scan support for 160 MHz
wcn36xx
* add SNR from a received frame as a source of system entropy
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmM3BGYRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuR3Af/XiuMlnDB6flq+M/kQHLWWvHybLw5aCJ7
l3yXhNFWxpBl2hQXtj17JSjVCYQmxbfrgRqhbNhyACO25bpymCb5QctB9X+Y7TwL
250JmuKvQfFx5oJNRfJ67dKTf3raloQYbdEMJNqySgebL+eSfrDskc9vaCLVDmCK
I994fl0Q1wUbJ6fbuIFd07ti8ay6UlSS/iakv4+nEeimabtZWJWlXBWYRpKpikdP
h9z2kPtss6yz6seaQuw6ny+qysYLi11Tp+Cued9XR3dWOOhB2X1tLHH0H02xPw76
9OJZEJHycP2juxjMfAaktHY+VX36GPLsMLUTVusH0h/Fdy3VG8YSAw==
=emmG
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.1
Few stack changes and lots of driver changes in this round. brcmfmac
has more activity as usual and it gets new hardware support. ath11k
improves WCN6750 support and also other smaller features. And of
course changes all over.
Note: in early September wireless tree was merged to wireless-next to
avoid some conflicts with mac80211 patches, this shouldn't cause any
problems but wanted to mention anyway.
Major changes:
mac80211
- refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO)
feature continues
brcmfmac
- support CYW43439 SDIO chipset
- support BCM4378 on Apple platforms
- support CYW89459 PCIe chipset
rtw89
- more work to get rtw8852c supported
- P2P support
- support for enabling and disabling MSDU aggregation via nl80211
mt76
- tx status reporting improvements
ath11k
- cold boot calibration support on WCN6750
- Target Wake Time (TWT) debugfs support for STA interface
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- implement SRAM dump debugfs interface
- enable threaded NAPI on all hardware
- WoW support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
wcn36xx
- add SNR from a received frame as a source of system entropy
* tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (231 commits)
wifi: rtl8xxxu: Improve rtl8xxxu_queue_select
wifi: rtl8xxxu: Fix AIFS written to REG_EDCA_*_PARAM
wifi: rtl8xxxu: gen2: Enable 40 MHz channel width
wifi: rtw89: 8852b: configure DLE mem
wifi: rtw89: check DLE FIFO size with reserved size
wifi: rtw89: mac: correct register of report IMR
wifi: rtw89: pci: set power cut closed for 8852be
wifi: rtw89: pci: add to do PCI auto calibration
wifi: rtw89: 8852b: implement chip_ops::{enable,disable}_bb_rf
wifi: rtw89: add DMA busy checking bits to chip info
wifi: rtw89: mac: define DMA channel mask to avoid unsupported channels
wifi: rtw89: pci: mask out unsupported TX channels
iwlegacy: Replace zero-length arrays with DECLARE_FLEX_ARRAY() helper
ipw2x00: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
wifi: iwlwifi: Track scan_cmd allocation size explicitly
brcmfmac: Remove the call to "dtim_assoc" IOVAR
brcmfmac: increase dcmd maximum buffer size
brcmfmac: Support 89459 pcie
brcmfmac: increase default max WOWL patterns to 16
cw1200: fix incorrect check to determine if no element is found in list
...
====================
Link: https://lore.kernel.org/r/20220930150413.A7984C433D6@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Entering LPS with PCIe APHY power cut closed would cause PCIe link issue.
To avoid the combinational issue, keep PCIe APHY power cut always on.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220927062611.30484-7-pkshih@realtek.com
Implement to power on/off BB and RF via MAC registers.
Add return type of chip_ops::disable_bb_rf, because it could fail to
disable. Also, correct naming of register 0x0200 used by the ops as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220927062611.30484-5-pkshih@realtek.com
Six channels are unsupported by 8852b, so mask them out to prevent to
access undefined registers in this chip.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220927062611.30484-3-pkshih@realtek.com
To enable/disable amsdu in set_tid_config, and currently only support to
configure all tids (==0xff) for AMSDU, not individual tid.
The command example is:
iw wlan0 set tidconf tids 0xff amsdu off
iw wlan0 set tidconf peer xx:xx:xx:xx:xx:xx tids 0xff amsdu on
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922012737.15091-1-pkshih@realtek.com
Align with the spec of 802.11ax, follow the conditions for not responding
with an HE TB PPDU. When there are OBSS that cannot interpret 26-tone RU
transmissions, we should disable such transmissions.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922012719.15037-1-pkshih@realtek.com
Support P2P client to process Notice of Absence (NoA) mechanism when it
connects with P2P GO applying an NoA schedule. We define some action
types including init, update, remove and terminate in h2c function to
enable/disable NoA schedule.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-6-pkshih@realtek.com
To handle a connected client using WMM-PS, the P2P GO also need to enable
this power save mechanism.
We add WIPHY_FLAG_AP_UAPSD flag to support it and define maximum number
of buffered frames the WMM GO may deliver to the WMM client.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-5-pkshih@realtek.com
Consider vif->p2p to set wifi_role to let firmware know current vif is
running as GC or GO. And, allow GC to enter PS mode, but disallow to enter
deep PS for now.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-4-pkshih@realtek.com
Check IEEE80211_TX_CTL_NO_CCK_RATE flag to avoid sending frames with
CCK rates in 2GHz band.
In TX flow, add IEEE80211_TX_CTL_NO_CCK_RATE flag to check and get its
lowest rate without CCK rates if the TX type is mgmt frames or data frames.
Besides, the decision of phy rate and retry rate in P2P mode are also
be handled.
In P2P GO mode, it should send beacon of no CCK rates in its frame rate.
Therefore, We add a condition to decide which rate is added to beacon
content.
Moreover, we avoid setting a mask of rates to be used for rate control
selection before and after connection in P2P mode.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-3-pkshih@realtek.com
To support P2P in driver, we set P2P interface mode to the wiphy
allocated for 802.11 PHY and add a change interface function to
switch the interface type to P2P.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-2-pkshih@realtek.com
Since we maintain coexistence as shared code, so move coexistence version
from chip specific attribute to a definition.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220920010939.12173-10-pkshih@realtek.com
Add control logic to operate Wi-Fi to BT scoreboard to control BT scan
priority. And patch mechanism parameter to enhance Wi-Fi throughput while
coexisting with BT profile & BT scan. Set PTA priority let Wi-Fi BT can RX
at the same time.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220920010939.12173-9-pkshih@realtek.com
If Wi-Fi driver send Wi-Fi status to BT via scoreboard too frequent in a
short moment, BT will loss some of them because of hardware response time.
To avoid this issue, change the code flow. Summarize the scoreboard changes
and if the value have changed, send the scoreboard to BT only once in
a coexistence processing cycle. It also can help to reduce driver I/O.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220920010939.12173-8-pkshih@realtek.com
To prevent LNA2 change its gain during a Wi-Fi aggregation packet while
GNT_BT pull high. Otherwise, changes of this gain will destroy the whole
aggregation when Wi-Fi RX.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220920010939.12173-7-pkshih@realtek.com
WiFi/BT combo module could only have two antenna, namely WL_S0 and WL_S1.
WiFi can use two antenna to TX/RX 2SS data, and BT can share one of the
antenna. This patch is to allow WiFi to TX/RX 1SS data like ACK/RTS/CTS to
improve Wi-Fi performance while coexisting with Bluetooth.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220920010939.12173-6-pkshih@realtek.com
This report is to record firmware call flow like notify events, and take
actions. This can help to address if firmware flow is in expectation.
Implement v1 parser to support 8852CE firmware report.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220920010939.12173-5-pkshih@realtek.com
This debug entry is to summarize important messages to quickly address
problem types, such as firmware hang, C2H/H2C stuck, or too much
occupation of BT A2DP. If unexpected something is addressed, we can dig
the problem via other debug messages that provide more detail information.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220920010939.12173-4-pkshih@realtek.com
To analyze debug log quickly, use readable name in string format instead.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220920010939.12173-3-pkshih@realtek.com
'cysta' is short for statistics for cycles. That is a circular buffer to
record snapshot status including beacon count, RX count, TX count etc.
Since 8852CE Wi-Fi firmware report this statistics in different format,
add v1 parser by this patch.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220920010939.12173-2-pkshih@realtek.com
If request_partial_firmware_into_buf() fails then "firmware" is not
initialized and the release_firmware(firmware) will crash.
Fixes: deebea35d6 ("wifi: rtw89: early recognize FW feature to decide if chanctx")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/YyMzDtX/3fUBnonC@kili
Update tx descriptor settings so broadcast packets on other ports can be
issued properly when DTIM count is 0. Before this, all broadcast packets
are sent via port 0 and won't be transmitted correctly.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220916033811.13862-8-pkshih@realtek.com
In monitor mode we should be able to received all packets even if it's not
destined to us. But after scan, the configuration was wrongly set, so we
fix it.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220916033811.13862-7-pkshih@realtek.com
This avoid potential memory leak under power saving mode.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220916033811.13862-6-pkshih@realtek.com
NAV upper register is to limit the maximum NAV value to prevent
unexpected NAV, but the old setting is too small to reflect NAV from
AP transmiting big MPDU at once.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220916033811.13862-3-pkshih@realtek.com
8852C needs this to change CMAC dma to full mode to keep receiving
packets after RX full event being resolved.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220916033811.13862-2-pkshih@realtek.com
SER (system error recovery) can deal with different crash types by
different levels of processes. Previous FW crash simulation triggers
a CPU exception which is one kind of SER L2 type. It can verify SER L2
flow which includes HW/FW restart.
Now, we want to increase crash simulation types. A debug function is added
to trigger control error in purpose for SER L1 simulation/verification.
And, debugfs fw_crash is extended to accept different parameters.
echo 1 > fw_crash:
simulate CPU exception as before
(keep 1 for compatibility with previous)
It will be catched and handled by SER L2.
(this requires HW/FW restart)
echo 2 > fw_crash:
simulate control error
It will be catched and handled by SER L1.
(driver and FW cooperate to recover this)
Besides, in order to apply to the above two cases,
rename RTW89_FLAG_RESTART_TRIGGER to RTW89_FLAG_CRASH_SIMULATING
and adjust where SER flow clears this bit for both L1 and L2.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220914035034.14521-5-pkshih@realtek.com
With FW >= v0.27.40.0, 8852C FW has feature to handle crash simulation.
Besides, use RTW89_WCPU_BASE_MASK to replace use of RTW89_WCPU_BASE_ADDR
and work for both 8852A and 8852C.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220914035034.14521-4-pkshih@realtek.com
Introudce a H2C feature to drop packets according to given parameters.
And, we implement instances to drop packets from BE, BK, VI, VO queues
by vif or sta. Then, we refine our callback of ieee80211_ops::flush to
deal with the case of drop=true via this feature.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220914035034.14521-3-pkshih@realtek.com
Seaprate calling of rtw89_h2c_tx() out of if-expression, and bypass the
return value to upper caller.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220914035034.14521-2-pkshih@realtek.com
Different chips use different register and mask for
tx dma channels, so concentrate them.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220912071706.13619-4-pkshih@realtek.com
Some PCI and MAC registers are changed for different
chips and correct them accordingly. And HCI MAD functions
belongs to MAC core, so move it to mac.h/.c.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220912071706.13619-3-pkshih@realtek.com
For 8852C, rtw89_pci_lv1rst_stop_dma() and rtw89_pci_lv1rst_start_dma()
are offloaded to FW L1 reset flow. So, driver no longer needs to do them.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220912071706.13619-2-pkshih@realtek.com
Add ops set_tid_config to support TID specific configuration.
We currently only support ampdu setting.
The command example is:
iw wlan0 set tidconf tids 0x3 ampdu off
iw wlan0 set tidconf peer xx:xx:xx:xx:xx:xx tids 0x2 ampdu on
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220912070014.10018-3-pkshih@realtek.com
Support setting HE GI and LTF values to the kernel via nl80211.
We currently only support some GI and LTF values settings.
The command example is:
iw wlan0 set bitrates he-gi-2.4 0.8 he-ltf-2.4 2
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220912070014.10018-2-pkshih@realtek.com
The variable cnt_connecting is to indicate if we are connecting to an AP.
This is an important clue for coexistence to assign more time slot to WiFi
side in this situation to ensure WiFi can establish connection.
Without this patch, compiler warns:
drivers/net/wireless/realtek/rtw89/coex.c:3244:25: warning: variable
'cnt_connecting' set but not used [-Wunused-but-set-variable]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220912021009.6011-1-pkshih@realtek.com
To reduce register IO, combine set_gnt_wl/set_gnt_bt to set the same
register one time. Because RTL8852C use different register to control
antenna path, so make correction of path control related debug logs.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220913092546.43722-8-pkshih@realtek.com
RTL8852C don't need to send the data trace_step which used to tell
firmware how many TDMA steps should record. Remove the member.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220913092546.43722-7-pkshih@realtek.com
Show TDMA information containing TDMA policy and time slot of Wi-Fi/BT in
debug message to check things are in expected. The v1 format contains
additional header, and remaining part is the same as original. So 8852CE
selects v1 version, and then everything like original.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220913092546.43722-6-pkshih@realtek.com
Parsing firmware error message from original version and v1 reports to
show up exception counter of commands from firmware in debug message.
Then, we can make sure exchange commands are correct totally.
In the later version Wi-Fi firmware(v1), the report format was changed.
With this update, we can yield correct report from proper struct.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220913092546.43722-5-pkshih@realtek.com
Because RTL8852A/RTL8852C use different firmware buffer size to
send C2H packet, it's necessary to use different size to parse C2H report.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220913092546.43722-4-pkshih@realtek.com
The later version Wi-Fi firmware will report null data TX times,
so the structure is different from before.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220913092546.43722-3-pkshih@realtek.com
The size limit of H2C commands is 2048. With regulatory that enables
U-NII-6 ~ UNII-8 channels, channel list length combining with channel info
length will exceed that. Split the channel list to parts and do scan
multiple times to workaround that.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-10-pkshih@realtek.com
This enables hw_scan function for 52c. The mechanism is similar to 52a
except that it adds modifications required for 6G channels and extends the
command length to make driver compatible to both newer and existing
firmware.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-9-pkshih@realtek.com
8852c transmits packets with slow response in deep ps mode,
and lead to low throughput. We need to call tx_wake for
each pakcet to trigger firmware wake earlier to avoid it.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-8-pkshih@realtek.com
rtw8852c could support deep ps mode if the firmware version
is greater than 0.17.34.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-7-pkshih@realtek.com
With suitable response rate, it can acknowledge peer packets are received.
Otherwise, peer could re-transmit again due to missing of ACK frames.
To achieve this, refer to RX rate and CMAC table to choose the smaller
as initial response rate.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-6-pkshih@realtek.com
With one path TX for 1SS rate, it can transmit higher power in 6GHz band
to yield better performance in high attenuation circumstance.
Signed-off-by: Yi-Tang Chiu <chiuyitang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-5-pkshih@realtek.com
The range of calibration time of RX DCK is quite wide from ~40us to
~1300us by experiments, and probability is about 0.1% for the cases larger
than 1000us. Though it can retry calibration and get positive result, it
will spend more time. Therefore, enlarge it to avoid warning and duplicate
calibration.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-4-pkshih@realtek.com
Enable MU-MIMO interference cancellation (MUIC) to yield expected
performance of receiving MU-MIMO packets on 6GHz.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-3-pkshih@realtek.com
Since control register address for DIG are different per IC, add a new
struct rtw89_dig_regs in chip info for each IC to define their own address.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-2-pkshih@realtek.com
Originally, we show average signal strength. To support TX diversity, this
patch prepares strength per path, then we can decide TX path.
RSSI: -54 dBm (raw=112, prev=110) [-57, -52]
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908074140.39776-5-pkshih@realtek.com
Two fields, TX/RX ANT NUM, are introduced to address variant TX/RX antenna
number of hardware. For example, a 1x1 chip with TX diversity, TX NSS = 1
and TX/RX ANT NUM = 2.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908074140.39776-3-pkshih@realtek.com
The definitions of bit fields in structure will be wrong in big-endian
platform, so use u32_get_bits() to access them.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908074140.39776-2-pkshih@realtek.com
The A-MSDU data needs to be stored per-link and aggregated into a single
value for the station. Add a new struct ieee_80211_sta_aggregates in
order to store this data and a new function
ieee80211_sta_recalc_aggregates to update the current data for the STA.
Note that in the non MLO case the pointer in ieee80211_sta will directly
reference the data in deflink.agg, which means that recalculation may be
skipped in that case.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Declare this to tell AP we can support beamformee over bandwidth 160M,
and then yield better performance in field.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220826061011.9037-3-pkshih@realtek.com
Writing address to kick hardware to initialize address CAM, and then poll
ready bit to determine completed. Old wrong code poll wrong register
address, so it can lead error and fail to bring up interface.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220826061011.9037-2-pkshih@realtek.com
Packets containing HTC field with legacy rate could be dropped by AP. If
TX rate of report is lower than MCS2, hardware might fall back rate to
legacy. Therefore, add a checking rule to avoid HTC field in this
situation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220826061011.9037-1-pkshih@realtek.com
Number of TX resource must be minimum of TX_BD and TX_WD. Only considering
TX_BD could drop TX packets pulled from mac80211 if TX_WD is unavailable.
Fixes: 52edbb9fb7 ("rtw89: ps: access TX/RX rings via another registers in low power mode")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220824063312.15784-2-pkshih@realtek.com
We turn off interrupt in ISR, and re-enable interrupt in threadfn or
napi_poll according to the mode it stays. If we are turning off interrupt,
rtwpci->running flag is unset and interrupt handler stop processing even
if it was called, so disallow to re-enable interrupt in this situation.
Or, wifi chip doesn't trigger interrupt events anymore because interrupt
status (ISR) isn't clear by interrupt handler anymore.
Fixes: c83dcd0508 ("rtw89: pci: add a separate interrupt handler for low power mode")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220824063312.15784-1-pkshih@realtek.com
The calibration value of XTAL offset may be too large in some wifi
modules, that the CFO tracking mechanism under the existing tracking
boundary can not adjust the CFO to the tolerable range. So we enlarge it.
Signed-off-by: Cheng-Chieh Hsieh <cj.hsieh@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220824061425.13764-1-pkshih@realtek.com
We find that suspend/resume tests cause 8852CE lost, because some pci
registers are changed for 8852CE. So, correct them accordingly.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220819064811.37700-6-pkshih@realtek.com
8852CE controls CLKREQ, ASPM L1, L1ss via wifi registers
instead, so change them accordingly.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220819064811.37700-5-pkshih@realtek.com
There is chance that PCI PHY auto adaption fail. When first time boot up,
software restore the right adaption value and close PHY auto adaption
mechanism.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220819064811.37700-4-pkshih@realtek.com
It is found that 8852ce loses some beacon after
enabling deep ps mode. We set TBTT shift to wake up
firmware early to open RF/BB for receiving beacon in time.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220819064811.37700-3-pkshih@realtek.com
When starting to send heavy traffic in low power mode,
driver will call multiple tx wake notify to wake firmware
within a short time. In this situation, firmware may miss
power mode change request from driver and leads to status
error. So we change driver to call power_mode_change at most
three times to make sure firmware could get the request.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220819064811.37700-2-pkshih@realtek.com
The bacam_v1 must do additional initialization, and H2C content of BA CAM
is also different. So, correct them accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220816013247.6243-3-pkshih@realtek.com
8852A has 2 BA CAM entries, but 8852C has 8 entries. Add a field to
discriminate their differences.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220816013247.6243-2-pkshih@realtek.com
TX power byrate:
doesn't change
TX power limit:
configure values for KCC and UK
refine a bit configuration vales
TX power limit_ru:
configure values for KCC and UK
refine a bit configuration values
change 6GHz to follow indoor setting
configure 6GHz values for ETSI
TX power shape:
change with TX power limit/limit_ru
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220812093116.56791-4-pkshih@realtek.com
Some chips' RF TX power limit/limit_ru tables start to configure some
negative values. Fix the setting logic to prevent negative values from
polluting fields of others.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220812093116.56791-2-pkshih@realtek.com
Because RTL8852c firmware handshake use different structure definition
with RTL8852a, so it's necessary to update a version for RTL8852c.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-10-pkshih@realtek.com
Because the later firmware had patched some new feature, it can control
the Wi-Fi/BT slots more efficiently. This patch enhance it for better
Wi-Fi SCC mode performance.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-9-pkshih@realtek.com
Due to the difference of Wi-Fi firmware supported feature, RTL8852C
need to defined more policy to enable the features.
(Ex: DBCC, Wi-Fi multi-role, TDMA instant and so on)
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-8-pkshih@realtek.com
The H2C format and support feature are different. The newer Wi-Fi firmware
and driver branch need to handshake more information like DBCC or P2P
connection info.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-7-pkshih@realtek.com
RTL8852C use a later version Wi-Fi firmware, there are some parameters
need to be defined. These new parameter can avoid some unexpected
TDMA mode while Wi-Fi enter/leave lps.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-6-pkshih@realtek.com
It is for setting up BT slot max length at BT auto slot mechanism.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-5-pkshih@realtek.com
Add a part of logic to parse type of ctrl report from firmware, and
remove Bluetooth packet counter count from driver, the feature was
moved to firmware at rtl8852c.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-4-pkshih@realtek.com
To configure the different chips with different coexistence version,
separated the firmware feature version matching number is necessary.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-3-pkshih@realtek.com
Update scoreboard setting to let Bluetooth know Wi-Fi power save state.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-2-pkshih@realtek.com
mac_txen time is to inform TMAC tx after rx air end.
Modify 8852c value to meet TB SIFS time.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220704023453.19935-7-pkshih@realtek.com
Prebkf time is to inform generating tx command if remaining backoff
time less than this setting value.
It might cause SER if generating tx command early in security mode.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220704023453.19935-6-pkshih@realtek.com
Calling rtw89_leave_lps() should hold rtwdev::mutex.
So, fix it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220704023453.19935-5-pkshih@realtek.com
Sometimes, BB might encounter RX problem on OFDM 6M. It's not quite
easy to happen, but if it happens, we will keep getting stuck on RX.
And, since we cannot properly receive layer 2 ACK, it also casues TX
problem, e.g. constantly retrying TX. Eventually, after some time, we
would get disconnected due to abnormal behavior.
Update break setting and phy status parsing time to make BB get out
of stuck state faster.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220704023453.19935-3-pkshih@realtek.com
Without this patch, our hardware attempts to perform dma while device
cpu restarts, and leads to iommu page faults caused by invalid requests.
Some platforms show warning messages as below:
rtw89_8852ce 0000:01:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT
domain=0x000a address=0x10000000004 flags=0x0030]
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220704023453.19935-2-pkshih@realtek.com
In current flow, FW is asynchronously loaded after alloc_hw(). It defers
the decision on FW feature map. It makes things difficult for us to decide
whether to hook chanctx ops, which should be decided while alloc_hw() is
calling. Still, asynchronous gets its advantages. So, we want to resolve
this without dropping them.
Based on multi-FW flag, RTW89_MFW_SIG, we can determine runtime FW is
multi-FW (MFW) or single FW (SFW). Both of them have a quite small chunk
for header at the head. The difference is that MFW doesn't describe version
code in its header while SFW does. So, we plan to extend MFW header for
version code. After that, in both cases, we can determine FW feature map by
just FW header. And, according to the map, we can decide chanctx.
So, we call request_partial_firmware_into_buf() to request a quite small
chunk before alloc_hw() to get a early FW feature map without affecting
things much and only use early map to decide whether to hook chanctx ops.
It means that if non-extended MFW is used at runtime, driver just acts
without chanctx as before. If extended MFW or SFW, which supports required
FW features, is used at runtime, driver can hook chanctx ops to mac80211 if
chip has configured support_chanctx_num > 0.
Besides, key point for now to support single one chanctx is whether HW scan
is supported at runtime. So, we configure all chip's support_chanctx_num to
1, and check if HW scan is supported at runtime via early FW feature map.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-14-pkshih@realtek.com
Some HW features are required if we hook chanctx ops to mac80211. With it,
mac80211 would expect the HW-supported variant ops exists on some behavior,
e.g. HW scan. But, HW features may depend on chip's FW or its development.
Besides, how many chanctx can be supported also depends on chip design.
We can neither decide whether to generally support chanctx ops nor how many
chanctx can be supported.
So, support_chanctx_num is added under chip info to deal with this by chip.
For now, all chip configure support_chanctx_num as 0. We haven't really
hook chanctx ops yet. So, chip can run without mac80211 chanctx as before.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-13-pkshih@realtek.com
Support mac80211 chanctx series ops. Still, currently support
single channel. Based on this premise, things should be similar
to before. So, we haven't dealt with relationship between vif
and chanctx in depth. Instead, we leave both ::assign_vif()
and ::unassign_vif() as noops for now.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-12-pkshih@realtek.com
After supporting more than one channel, we need entity mode to decide
how to set current channel(s) on the sub-entities. This decision may
happen on set_channel() and rtw89_core_set_chip_txpwr().
For now, we support single one channel and use only first HW entry,
i.e. RTW89_SUB_ENTITY_0, RTW89_MAC_0, RTW89_PHY_0. Without something
unexpected, the entity mode should always be RTW89_ENT_MODE_SCC after
recalcated, where SCC means single channel concurrency. So, an assert
is added in set_channel() and rtw89_core_set_chip_txpwr().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-11-pkshih@realtek.com
While idle, we need a default chandef to set channel for things,
such as scan. Before support of mac80211 chanctx, mac80211 would
configure a default one on ieee80211_hw::conf::chandef. And we
just queried it whenever we did set channel. However, after support
of mac80211 chanctx, the flow won't work like before.
Besides, we don't now query chandef from ieee80211_hw::conf::chandef
either. So, similar to mac80211 without using chanctx, we configure
the default chandef with ieee80211_channel of index 0 in 2GHz.
Although we have not added the support of mac80211 chanctx here,
this configuration should be compatible before that. So, we commit
this ahead.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-10-pkshih@realtek.com
Originally, we didn't support mac80211 chanctx, so it's expected that
ieee80211_hw::conf::chandef would be filled by mac80211. And then, we
could just query it whenever we need the current chandef.
However, we are planing to support mac80211 chanctx. After that, the
above assumption would be broken. So, we adjust a bit ahead to reduce
future works about mac80211 chanctx.
After this, we don't query ieee80211_hw::conf::chandef directly, and
we add a map, entity_map, to HAL to indicate which chandef came from
stack. And it will later be used to recalcate entity mode.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-9-pkshih@realtek.com
For future support on multiple channels by multiple sub-entities,
we need to manage parameters of each channel instance like rtw89_chan,
rtw89_mac_idx, rtw89_phy_idx. So, we adjust related channel callback
functions and centrally conrtol these parameters in set_channel().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-8-pkshih@realtek.com
For future support on multiple channels, there will be settings of
multiple sub-entities that we need to control. We don't want such
settings to be scattered all over the place. So, we centrally manage
controls of rtw89_phy_idx for RFK in set_channel().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-7-pkshih@realtek.com
For future support on multiple channels, it would be disturbing if we
still allow scattered leaf functions of TX power to query and manage
channel related control by themselves.
So, query rtw89_chan only on top functions. Then, pass it via functions
to make sure that the values coming from the same struct rtw89_chan.
Besides, fix rtw8852a_set_txpwr_offset() from rtw8852a_set_txpwr_ctrl()
to rtw8852a_set_txpwr(). TX power offset should consider current band,
so move it to chip_ops::set_txpwr() which will be called every time that
channel is set.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-6-pkshih@realtek.com
Sometimes we need to write current rtw89_chan outside set_channel(),
e.g. during HW scan, we adjust it to align FW process through C2H.
However, we don't have full parameters to fill entire rtw89_chan.
And it will breakage if we update only part of current rtw89_chan.
That is what we don't want to see because most flows throughout
driver treat rtw89_chan as a whole.
So, we divide struct rtw89_chan to basic part and derived part. The
basic part contains the parameters which we are always able to know.
And the derived part will be calculated by the basic part. Then, a
central function, rtw89_chan_create(), is added to deal with this.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-5-pkshih@realtek.com
We are planning to support mac80211 chanctx. To reduce future works,
the driver architecture is adjusted first to isolate related things.
According to chip, our HW may have multiple sub-entities to support
multiple mac80211 chanctx. Struct rtw89_chan has been introduced for
things about channel/band/subband/... Now introduce struct rtw89_chan_rcd
to record difference after assigning new one of struct rtw89_chan.
We will implement and support chanctx with single channel first, i.e.
only use entry in RTW89_SUB_ENTITY_0, before handling dual channels.
Our hierarchy in planning will become as the following.
DEV
-> HAL
---> entity (manage status across sub-entities)
-----> sub-entity[*] (support mac80211 chanctx)
where each sub-entity contains one struct rtw89_chan.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-4-pkshih@realtek.com
Introduce struct rtw89_chan ahead to encapsulate stuffs from struct
rtw89_channel_params. These stuffs have a clone in HAL and are used
throughout driver. After multiple channels support, it's expected that
each channel instance has a configuration of them. So, we refine them
with struct rtw89_chan by precise type first, and will re-arrange HAL
by struct rtw89_chan in the following as well.
(No logic has changed.)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-3-pkshih@realtek.com
We need to invoke the callback of the changed band at the first
set_channel() after every power-off. Originally, we forced the
channel to be 0 when doing power-off, and then determined things
by comparing channel with 0.
However, deciding on such things by channel might be confusing.
It's also confusing to use this kind of decision when we consider
multiple channels in the follow-up patches. So, another flag,
entity_active, is added ahead to HAL to deal with this.
Besides, we also need to check if entity is active when we set
TX power.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-2-pkshih@realtek.com
Correct IMR settings to let self error recover mechanism works accurately.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220802123816.16685-1-pkshih@realtek.com
It's unnecessary to iterate leaving PS mode.
So, move it out of the iteration.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220802123712.16577-1-pkshih@realtek.com
SER (system error recovery) L1 (level 1) has a step-by-step handshake
process with FW. These handshakes still rely on B_AX_HS0ISR_IND_INT_EN.
So, even already during recovery, we enable this bit in IMR.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220721074952.19676-1-pkshih@realtek.com
When calling start/stop_ap(), mac80211 already has a protected
link_conf pointer. Pass it to the driver, so it shouldn't
handle RCU protection.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously we only disable invalid reports for 52A, since we plan to
support more ICs in the future, enable settings for those as well.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-12-pkshih@realtek.com
TX BD (TX ring index) and TX WD (WiFi descriptor buffer) are freed
asynchronously. With burst packets, we free TX WD, but the corresponding
TX BD couldn't be freed yet. Then, TX can possibly get stuck due to no
more TX BD.
To avoid this, ignore reclaiming TX BD only if TX WD is no free space,
because at this moment TX BD must have some spaces. Otherwise, we reclaim
TX BD to resolve TX stuck issue.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-11-pkshih@realtek.com
In low power mode, regular IO is power off, so we don't schedule napi to
poll RX and TX completion. Therefore, calling ieee80211_rx_napi() with
napi instance causes long RX latency. To fix this, use NULL as argument,
and then it can use netif_receive_skb_list() to receive.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-10-pkshih@realtek.com
Somehow, firmware could report invalid TX rate, and we consider the
invalid rate as 0 that will make a wrong decision. So, drop invalid
reports, and also suppress the warning message.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-9-pkshih@realtek.com
Some warning messages could bother users. With proper handling, these
situations don't really affect usage, but we still need to keep monitor
these messages. If they happen frequently, we must review driver or
hardware design to clarify.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-8-pkshih@realtek.com
To improve VO throughput, we enable VO TX AMPDU.
We measure the latency of enable or disable VO TX AMPDU. The experimental
results show that the difference between the two is insignificant only
300µs, so the little impact can be ignored for user experience.
Moreover, we found some APs will have a group key handshake timeout issue
when the EAPOL's TID is already setup BA session. Therefore, when
transmitting EAPOL, if EAPOL's TID BA session is already setup, we need
to delete it.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-7-pkshih@realtek.com
The potential TX stuck occurs when there are lots of packets to be
transmitted and the boundary of the tx_resource is hit. Add this
patch to avoid the TX stuck when burst traffic.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-6-pkshih@realtek.com
In STA mode, if peer is TDLS. Allocate a BSSID CAM entry with peer's
address to match address properly, and then hardware can ACK peer's
packets and receive packets to driver.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-4-pkshih@realtek.com
Normally, we allocate a BSSID CAM to a vif. By hardware design, we must
allocate a BSSID CAM to each TDLS peer, so separate BSSID CAM operations
that will be used by later patches.
This patch doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-3-pkshih@realtek.com
Normally, we only allocate an address CAM and single one MAC ID to AP in
STA mode. To support TDLS, we handle TDLS peers like AP handles stations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-2-pkshih@realtek.com
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In start_ap and stop_ap mac80211 callbacks pass the link_id
to the drivers.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an new state, RTW89_PHY_DCFO_STATE_HOLD, to keep CFO acceleration
after CFO_PERIOD_CNT if the traffic is UL-OFDMA, which is calculated
based on RX trigger frame counter.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608113224.11193-4-pkshih@realtek.com
Adding this allows us to maintain trigger frame statistics, which is
required for our CFO tracking decisions.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608113224.11193-3-pkshih@realtek.com
The BSSID mask of H2C is used to match BSSID of receiving packets.
Normally, we set six bits BSSID mask to exactly match BSSID of packets
sent by target AP. After we support multiple BSSID, it could connect a
nontransmitted BSSID, so we can only match first five bytes of BSSID.
That means we could possibly receive other AP's packets if only the last
byte of BSSID is different from target AP.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220530112743.106857-1-pkshih@realtek.com
Since SAR is more expected to follow U-NII bands to plan subbands,
division of 6GHz band is quite different from defined enum of subbands
which is used by PHY in most cases. It's hard and painful if we want to
keep using the same enum on SAR. So, we introduce another enum for SAR
subbands and adjust SAR flow to use it.
Besides, since 6GHz SAR subbands won't be divided with edge alignment,
some cases will span two SAR subbands. For these cases, we describe them
within an array of rtw89_sar_span and take the smaller one between SAR
settings of the two subbands.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220520071731.38563-6-pkshih@realtek.com
RX DCK is receiver DC calibration. To keep good RF performance, do this
calibration again if the delta of thermal value from the last calibration
is more than 8.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220520071731.38563-5-pkshih@realtek.com
This watchdog timeout status bit indicates hardware gets wrong, so run SER
L2 flow that calls mac80211 to restart hardware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220520071731.38563-4-pkshih@realtek.com
Add this check to avoid crash by dereferencing a null pointer. When hwscan
fails due to no memory or dma failure, the scan flag in ieee80211_local is
cleared. So mac80211 determine that it's not hw_scan then calls
sw_scan_complete() with null vif, which is also freed during the fail.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220520071731.38563-3-pkshih@realtek.com
Previously channel maintained by driver could be different from the
ones hardware actually is. Restore these variables back to prevent
unexpected behavior.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220520071731.38563-2-pkshih@realtek.com
The design of INT indicator register (R_AX_PCIE_HIMR00_V1) is to reduce IO
during frequent interrupts, because it can stop chip sending interrupt to
host if we just set this indicator to 0, not all IMR(s). This indicator
register looks like a root interrupt controller of wifi chip.
However, we can't set all other IMR(s) to 0 during we are running on
interrupt service routine, or the indicator register can't reflect the
status of certain interrupt happened during this period, and then miss
some interrupts especially SER interrupt events.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-7-pkshih@realtek.com
Before 6 GHz band was supported, i.e. only 2 GHz and 5 GHz, they were the
same from the numerical point of view. However, after 6 GHz band support,
we need to do this conversion logically.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-6-pkshih@realtek.com
Update notes:
update the following to HALRF_027_00_052
TX power by rate table
TX power limit table
TX power limit RU table
TX shape table doesn't seem to be changed on HALRF_027_00_052
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-5-pkshih@realtek.com
To make user space can set TX antenna via iw command. Then, we can diagnose
antenna is connected properly or not, and measure TX power in single path.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-3-pkshih@realtek.com
When peer's NSS, rate or bandwidth is changed, we update RA(rate adaptive)
mask to ensure transmitting packets properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-2-pkshih@realtek.com
BSSID CAM is a kind of CAM that is used to determine if we receive a packet
or not. Add an entry to assist in debugging.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-6-pkshih@realtek.com
EDCCA signal can block transmitting in certain situation, so ignore this
signal and use others to decide transmitting time.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-4-pkshih@realtek.com
Set proper setting according to RX quota, and then it doesn't break buffer
due to size of received packet exceeding buffer size.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-3-pkshih@realtek.com
Modify NBI and PD boost settings according to different primary channels.
This setting can decrease the false alarm induced by DC.
Signed-off-by: Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-2-pkshih@realtek.com
This initial vesion is usable now. It can support STA, AP and monitor
modes, so we can add 8852ce to Kconfig and Makefile.
We are still working on some features, such as deep power save, and BT
coexistence. But, this version still can have a good WiFi-only performance
already, and will continue to fine tune power consumption.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-9-pkshih@realtek.com
By experiments, it spends ~45/1090~2480us to enter/leave low power mode,
so the old polling interval 1000us can waste time. Use smaller polling
interval depends on experimental results to reduce the time to transition
state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-5-pkshih@realtek.com
The chip_info include BT coexistence tables, size and number of hardware
components, and supported functions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-4-pkshih@realtek.com
The commit 16b44ed0ff ("rtw89: add RF H2C to notify firmware") is to
add firmware command, and this commit is to prepare the channels. Then,
firmware can get proper channels.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-2-pkshih@realtek.com
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
8852c needs two backup buffers, so we enlarge the array. But, 8852a still
needs only one, so it only uses first element (index zero).
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-9-pkshih@realtek.com
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-8-pkshih@realtek.com
RX DCK is receiver DC calibration. Do this calibration when bringing up
interface and going to run on AP channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-7-pkshih@realtek.com
RCK is synchronize RC calibration. It needs to be triggered only once when
interface is going to up.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-6-pkshih@realtek.com
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.
To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-5-pkshih@realtek.com
LCK is short fro LC Tank calibration. Do this calibration once driver
loads RF parameters table. Since the characteristic can be changed by
temperature, we do this calibration again if difference of thermal value
is over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-4-pkshih@realtek.com
DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output analog signals as expected.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-3-pkshih@realtek.com
These tables are used by RFK (RF calibration) to set parameters. These
parameters can trigger certain calibration, or configure/reset settings
before and after RF calibrations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-2-pkshih@realtek.com
Eliminate the following coccicheck warning:
./drivers/net/wireless/realtek/rtw89/rtw8852c.c:2556:2-3: Unneeded
semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220427003142.107916-1-yang.lee@linux.alibaba.com
Hardware reports PPDU status containing encoded channel index to driver,
so we decode it and then fill freq and band.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-14-pkshih@realtek.com
Read thermal value, and then we can use EWMA thermal value to do RF
calibrations if the value is changed over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-13-pkshih@realtek.com
Three chip_ops are implemented in this patch. The ::set_txpwr_ctrl and
::init_txpwr_unit are called when we up interface and then configure TX
power registers to initial values. The ::set_txpwr_ctrl is to configure
'txpwr_ref' to make basic output TX power of OFDM and CCK rate to be the
same. The ::init_txpwr_unit is to initialize TSSI (a method to do TX power
compensation depends on thermal value) control and bandedge.
The ::set_txpwr is called once switching channel. First, it sets TX power
for each rate section (e.g. CCK, OFDM), and then sets TX power offset
between 1SS and 2SS rate. Finally, it sets TX power limit to prevent
power over regulation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-12-pkshih@realtek.com
IQK results in hardware has two copies that are used by firmware to switch
these two to support MCC.
This H2C tell firmware the corresponding channel and band of each IQK
results, and currrent one.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-10-pkshih@realtek.com
When disconnecting, it warns somethings after power is off, and we can't
do HCI IO. So, add this patch to avoid below messages:
rtw89_8852ce 0000:03:00.0: timed out to flush pci txch: 11
rtw89_8852ce 0000:03:00.0: failed to pre-release fwcmd
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-9-pkshih@realtek.com
RPP is to report certain skb(s) can be freed, and TX BD indicates which
TX descriptors can be freed. Normally, TX BD is happened before RPP.
In low power mode, RPP can happen ahead, so change flow to handle this
case.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-8-pkshih@realtek.com
In low power mode, we need to pause PCI to configure IMR and PCI ring
index registers accordingly, because the regular registers are power-off
in this mode.
In the transition moment named paused in code, we can't touch ring index,
so don't kick off DMA immediately. Instead, queue them into pending queue,
and kick off after the moment.
There are three low power modes, which are RF off/clock gate/power gate,
but PCI enter low power mode in later two modes only. So, add a mask
to achieve this.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-7-pkshih@realtek.com
Normally, we re-enable interrupt by napi_poll, but for this special
situation, we must turn it on immediately because napi_poll isn't
scheduled.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-6-pkshih@realtek.com
In lower power mode, there are very low amount of RX, and it must process
in a separated function instead of schedule_napi(), because the existing
napi_poll does many things to optimize performance, but not all registers
can access in low power mode. The simple way is to use threadfn to process
the simple thing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-5-pkshih@realtek.com
To reclaim TX BD, we need to read hardware reading index to determine if
any DMA is complete. Since this IO spends time, do this thing only if we
really need it when TX BD has no free buffer corresponding to target skb.
The experimental result shows that reading counter decreases from 26,000
to 130 per second.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-4-pkshih@realtek.com
RPWM/CPWM are registers that can set and check low power mode. Since chips
use different address, add a field to access them in common flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-3-pkshih@realtek.com
8852CE uses different but similar IMR/ISR registers, and its masks are also
different in various states, so add config_intr_mask ops to configure masks
according to under_recovery or low_power states.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-2-pkshih@realtek.com
During setting channel, we need to backup/restore and disable/enable some
settings. The settings include SCH (scheduler channel), PPDU status report,
and RF components, DFS and ADC.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-13-pkshih@realtek.com
BB does many settings during setting channel. First is to configure CCK
for 2G channels, and then basic channel and bandwidth settings with a
encoded channel index that will report to driver when we receive packets.
Configure spur elimination to avoid spur of CSI and NBI tones in certain
frequencies. Also, it initializes BT grant to arrange path sharing with
BT according to band. Finally, reset TSSI and BB hardware to ensure it
stays in initial state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-12-pkshih@realtek.com
Add parser for bb gain table and configure bb gain table for 8852c.
While ctrl_ch, obtain bb gain error settings and write them to phy.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-7-pkshih@realtek.com
chip_ops::bb_sethw is to initialize BB settings out of BB parameters
tables. Once switching channel or initialing, we do chip_ops::bb_reset to
reset hardware counters and states to make things in expectation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-6-pkshih@realtek.com
TSSI is used to manage TX power with thermal value as a factor. This patch
is to configure bandedge to TX proper waveform.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-5-pkshih@realtek.com
TX power track tables are used to do TX power compensation according to
thermal value. In order to work in existing and new chip, add new 6G
entries, and change type from u8 to s8.
Internal version table is HALRF_027_00_031.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-4-pkshih@realtek.com
TX power depends on rate, but must follow regulation for specific country.
Once asked to set channel, we configure registers according to these TX
power tables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-3-pkshih@realtek.com
These parameters are used to initialize BB and RF hardware when we are
going to bring up interface and start to transmit and receive.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-2-pkshih@realtek.com
DCTL is short for D-MAC control that V1 chip uses this H2C to configure
security CAM. Implement the callers in next patch.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413010804.8941-3-pkshih@realtek.com
In order to support new chip that has capability of 160M, we need new
format to fill new information, so add a new V1 ID for newer use. Since
most fields are the same, fill fields according to the function ID of chip.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413010804.8941-2-pkshih@realtek.com
Change the struct and the uses to const to reduce data.
$ size drivers/net/wireless/realtek/rtw89/ser.o* (x86-64 defconfig w/ rtw89)
text data bss dec hex filename
3741 8 0 3749 ea5 drivers/net/wireless/realtek/rtw89/ser.o.new
3437 312 0 3749 ea5 drivers/net/wireless/realtek/rtw89/ser.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/2fd88e6119f62b968477ef9781abb1832d399fd6.camel@perches.com
Initialize registers to default values, such as PTA and GNT pin, and set
pin MUX according to number of antenna on hardware module.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-10-pkshih@realtek.com
Separated DIG RX gain, IGI configurations from not supportted HW using
"support_igi" capability flag.
Signed-off-by: Johnson Lin <johnson.lin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-9-pkshih@realtek.com
Disable watchdog timer to prevent it timeout suddenly.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-8-pkshih@realtek.com
The bit B_AX_SS_NONEMPTY_SS2FINFO_EN should be clear, because we configure
C-MAC as hardware TX/RX mode.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-6-pkshih@realtek.com
Turn on ERR IMR, and then firmware can capture interrupts reflecting
errors to recover hardware states.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-5-pkshih@realtek.com
Similarly, create functions to set specific C-MAC masks for firmware
recovery.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-4-pkshih@realtek.com
These interrupts are used by firmware to recover hardware. Create
functions to set specific D-MAC masks to replace plain register settings.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-3-pkshih@realtek.com
add `break` to fix warning of unannotated fall-through between switch
labels.
Fixes: 14f9f47900 ("rtw89: ser: control hci interrupts on/off by state")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-2-pkshih@realtek.com
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Without this patch, hw scan won't stay long enough on DFS/passive
channels. Found previous logic error and fix it.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220401055043.12512-5-pkshih@realtek.com
Turn off coexistence driver control, let firmware can control the
traffic during scan. This prevents potential unexpected behavior of
the BT driver.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220401055043.12512-4-pkshih@realtek.com
Add a dummy function for packet offload to eliminate warning message
"c2h class 1 func 2 not support". This c2h is for debug purpose and
its presence itself can do the work, so further parsing won't be
required for now.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220401055043.12512-3-pkshih@realtek.com
Previously we only consider single interface's status, idle mode
behavior could be unexpected when multiple interfaces is active.
Change to enter/leave idle mode by mac80211's configuration state.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220401055043.12512-2-pkshih@realtek.com
Address info registers are used to configure size of DMA address info to
point skb->data. With different size, it can support different number of
scatters.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220325060055.58482-6-pkshih@realtek.com
The pre_init is used to initialize partial PCI function during PCI probe.
It doesn't need to initialize all functions, so probe can be faster.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220325060055.58482-4-pkshih@realtek.com
The PCI code of 8852AE and 8852CE are different, but the flow and register
names are similar. To reuse the code, add a struct to define register or
value accordingly. We also use chip id to control the slightly different
flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220325060055.58482-2-pkshih@realtek.com
The smatch reports:
rtw8852a.c:1857 rtw8852a_btc_set_wl_txpwr_ctrl() error: uninitialized symbol '_cur'.
rtw8852a.c:1858 rtw8852a_btc_set_wl_txpwr_ctrl() error: uninitialized symbol '_cur'.
This is because rtw89_mac_txpwr_read32() can possibly return before setting
argument _cur, and the caller will use the uninitialized value. To fix this
problem, check the return value of rtw89_mac_txpwr_read32().
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318035202.42437-1-pkshih@realtek.com
8852C uses different fields to represent RX bandwidth. Since other fields
are the same, I check chip_id to get bandwidth instead of creating another
v1 function.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-12-pkshih@realtek.com
The newer chip will generate security header itself, so don't set
IEEE80211_KEY_FLAG_GENERATE_IV in this kind of chip. But, it needs to fill
key_index, PN and 802.11 header length to TX descriptor, and then hardware
uses these to generate security header.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-11-pkshih@realtek.com
The txdesc is descriptor related to skb->data. The v1 version contains
8 dwords txwd_body and 6 dwords txwd_info, and the format is also different
from original one.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-10-pkshih@realtek.com
The txaddr_info is used to fill the DMA address of skb->data. The v1
version can support up to 10 entries, but the maximum size of each entry
is 2047, so it fill more than one entry for large packet, like 3000 bytes.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-9-pkshih@realtek.com
8852A and 8852C use different H2C header and size, so add h2c_desc_size
to allocate different header size and fill content by fill_txdesc_fwcmd.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-8-pkshih@realtek.com
Bypass IGI, known as Rx gain, adjustment flow for incompatible hardware
architectures.
Signed-off-by: Johnson Lin <johnson.lin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-7-pkshih@realtek.com
Refinement of DIG flow, a mechanism to adjust Rx gain for better Rx
performance, by packing IGI(initial gain index) configuration flow into
one function.
Signed-off-by: Johnson Lin <johnson.lin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-6-pkshih@realtek.com
Update notes:
Configure rtw89_regulatory for 6G band according to country.
Adjust country GB to use RTW89_UK entry on all bands.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-5-pkshih@realtek.com
Wrap regd debug dump into a macro and add dump for 6G band field.
Extend the macro used to configure regd table to account for multiple
bands beyond 2G and 5G.
And the follow-up commit will configure the corresponding values for
6G band into regd table.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-4-pkshih@realtek.com
Update notes:
TX power by rate table is not changed.
TX power limit table configures values for UK.
TX power limit RU table configures values for UK.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-3-pkshih@realtek.com
Add RTW89_UK to enum rtw89_regulation_type.
The follow-up commit will configure the corresponding values for it
to TX power tables.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-2-pkshih@realtek.com
An export symbol costs about 40 bytes (in x86 with gcc), so use a structure
containing these small arrays to reduce code size.
text data bss dec hex filename
34932 1410 0 36342 8df6 mac.o (before)
34276 1258 0 35534 8ace mac.o (after)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220315015522.11366-1-pkshih@realtek.com
Originally, there is already a mechanism, SER (system error recover),
to deal with HW/FW recovery. After FW v0.13.36.0, FW supports a H2C
(host to chip) command to make a CPU exception. Then, SER is supposed
to catch this FW crash and do L2 reset. This feature is a simulation
to verify if flow of recovering from FW crash works.
Usage of fw_crash debugfs is as the following.
$ echo 1 > fw_crash // trigger FW crash and wait SER handling
$ cat fw_crash // return 0 if restart has been done
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-9-pkshih@realtek.com
As the fw features gradually increase, it would be better that
we have a set of methods to maintain fw features instead of using
scattered bool variables.
We reconstruct the way fw recognize features, and introduce
RTW89_CHK_FW_FEATURE() / RTW89_SET_FW_FEATURE() to check / set
fw features for uses.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-8-pkshih@realtek.com
Read FW backtrace entry through FW reserved payload engine, and then
add FW backtrace dump during SER (system error recover) L2 reset process.
It contains a list of RA (return address) and SP (stack pointer) which
gives us a chance to trace back the call stack of FW.
Moreover, if core dump might have wrong content due to error during
dumping, we won't invoke device core dump framework. For this case,
rtw89_ser_cd_free() is added to free buffer by ourselves.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-7-pkshih@realtek.com
When FW encounters exception or assertion, SER L2 reset process will start.
It will dump some error information and re-download FW eventually. Since
such errors are usually critical, we would like to keep more information
about error to increase possibility of analysis and debugging FW. We first
add FW payload engine (fw reserved playoad engine, fw_rsvd_ple) memory
dump. FW will record things like CPU registers, backtrace entry, etc. in it
for debugging.
Moreover, device core dump framework is used and wrapped to collect kinds
of dumps during SER L2 reset process.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-6-pkshih@realtek.com
While SER (system error recover) is processing, it's supposed to mean
something is under recovery. So, disable interrupts (excluding the one
of halt which could be used during SER) to avoid unexpected behavior.
And then, enable interrupts after SER is done.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-5-pkshih@realtek.com
The raw error code might combine error scenario and error status.
But, the error scenario isn't parsed previously. It makes us mishandle
cpu exception and assertion. Now, we correct the error status for them.
Besides, a few uses of error status are refined.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-4-pkshih@realtek.com
Previously, mac_mem_base_addr_table was declared in debug.c locally
because it's only used via debugfs to dump mac memory. Now, we plan to
refine SER (system error recover) flow which will also need to dump mac
memory to somewhere as information for error which is catched. So, we
move mac_mem_base_addr_table to mac.c rtw89_mac_mem_base_addrs earlier
as common code.
(no logic is changed)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-3-pkshih@realtek.com
The CAM, meaning address CAM and bssid CAM here, will get leaks during
SER (system error recover) L2 reset process and ieee80211_restart_hw()
which is called by L2 reset process eventually.
The normal flow would be like
-> add interface (acquire 1)
-> enter ips (release 1)
-> leave ips (acquire 1)
-> connection (occupy 1) <(A) 1 leak after L2 reset if non-sec connection>
The ieee80211_restart_hw() flow (under connection)
-> ieee80211 reconfig
-> add interface (acquire 1)
-> leave ips (acquire 1)
-> connection (occupy (A) + 2) <(B) 1 more leak>
Originally, CAM is released before HW restart only if connection is under
security. Now, release CAM whatever connection it is to fix leak in (A).
OTOH, check if CAM is already valid to avoid acquiring multiple times to
fix (B).
Besides, if AP mode, release address CAM of all stations before HW restart.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-2-pkshih@realtek.com
These function is used to stop transmitting when we are going to switch
channels or do some RF calibration. Before these operations, we need to
stop channel transmission and backup setting into parameter tx_en. After
operations are done, resume transmitting by backup parameter tx_en.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-13-pkshih@realtek.com
In order to support 8852C that uses 32 bits to control TX types.
This patch doesn't really use 32 bits tx_en yet, but next patch will
use it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-12-pkshih@realtek.com
Use if() style would be clear than "? :", because the else cases are
always 0. The read val from rtw89_mac_read_lte() isn't used, so remove
this statement.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-11-pkshih@realtek.com
The BT-coexistence uses these function to control antenna and TDMA, so
implement the variant type to support all chips.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-10-pkshih@realtek.com
Initialize FW status and disabled H2C function if CPU disabled. Then, it
can reset to initial state.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-9-pkshih@realtek.com
8852C add new hardware feature -- preload window, which is used to load
more data to D-MAC, so it can possibly yield better performance.
This patch is to configure preload and reserved size for next window.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-8-pkshih@realtek.com
Modify functions that control D-MAC (data MAC) and LDO to support variant
chips.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-7-pkshih@realtek.com
The format of RF parameter is changed; it doesn't encode delay parameters
into table, but the delay coding becomes regular pair of register address
and value.
To help firmware to recover RF register settings, we need to download
these parameters to firmware. For v1 format, only download partial
parameters (ignore them with addr < 0x100).
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-6-pkshih@realtek.com
Using encoded address which BIT(16) is used to discriminate which region is
going to access. Illustrate the calling flow as below
rtw89_phy_write_rf_v1() -+-> rtw89_phy_write_rf() // old interface
+-> rtw89_phy_write_rf_a() // new interface
Signed-off-by: Chung-Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-5-pkshih@realtek.com
Configure this TX power to indicate TX power offset that uses to transmit
TB (trigger base) uplink frames.
Also, shrink the unit of TX power offset changes to suitable type s8.
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-4-pkshih@realtek.com
The CFO tracking algorithm is the same, but control methods are different.
Set parameters via xtal serial interfaces (SI).
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-3-pkshih@realtek.com
The dcfo_comp is digital CFO (central frequency offset) compensation.
Since the flow can be shared with all chips, add chip parameters to support
variant register address and format.
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-2-pkshih@realtek.com
There are some spelling mistakes in some literal strings. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220316234242.55515-1-colin.i.king@gmail.com
smatch reports that:
fw.c:1997 rtw89_append_probe_req_ie() error: uninitialized symbol 'ret'.
This can be a issue only if no band is supported by the chip, but it is
impossible. So, it is still safe without this patch.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220311020007.20414-1-pkshih@realtek.com
DAV is an another efuse region that new chip, like 8852C, has this region.
Extend the code to read it, and convert the physical map to logical map
followed by original logical map.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-12-pkshih@realtek.com
This is a register-based H2C/C2H interface to exchange data with firmware.
Since the register addresses of 8852A and 8852C are different, add fields
to chip_info to support this.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-9-pkshih@realtek.com
The HCI_FUNC_EN address of 8852C is different from existing chipset, so
add a chip_info::hci_func_en_addr to fill the address individually.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-8-pkshih@realtek.com
New chipset uses individual power_{on/off} functions to replace old power
sequences, because it is hard to represent new complicated flow in a
sequence table.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-7-pkshih@realtek.com
Only 8852A may get wrong chip version if power isn't on, so it needs
additional actions to correct the version. Later chips don't need those.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-6-pkshih@realtek.com
We have had a struct rtw89_pci_ch_dma_addr to describe register address,
so use it as regular. Since the addresses should be changed dynamically
according to operating mode, I don't change it to be constant.
These changes don't affect the logic, so I put them in this separated
patch.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-5-pkshih@realtek.com
To work properly in 6G band, declare HE 6G capabilities. Without this fix,
it can only TX/RX with OFDM rates.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307012741.6371-1-pkshih@realtek.com
Bit 2 and 3 are reserved on 5/6 GHz and bit 1 is reserved on 2.4 GHz,
so the driver should only set the non-reserved bits according
to band.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220301004331.6621-1-pkshih@realtek.com
We found management frames get stuck when wifi chip
enters low ps mode. So we add one notify wake function
to trigger wifi chip into normal mode before forwarding
management frames.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220225030851.13327-3-pkshih@realtek.com
Declare this function allows us to use customized scanning policy, so
each scan takes less time. This is a similar implementation to hw_scan
in rtw88, except that we offload more items to firmware and extend the
maximum IE length. For backward compatibility, we fallback to sw_scan
when firmware does not support this feature.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220225030851.13327-2-pkshih@realtek.com
Calculate the offset of center and primary frequencies to get hardware
indices of center channel and primary channel, and then use them to
configure hardware to a specific channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220222032103.29392-1-pkshih@realtek.com
Set the boundaries of x'tal value to avoid extremely adjusted results,
causing severely unexpected CFO.
Signed-off-by: Yi-Tang Chiu <chiuyitang@realtek.com>
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220218034537.9338-1-pkshih@realtek.com
Add handling to fill struct rtw89_txpwr_limit and rtw89_txpwr_limit_ru
for 160Mhz bandwidth case. And enlarge RTW89_5G_BW_NUM because the chip
under planning can support 160Mhz bandwidth on 5G band.
Moreover, refine the filling of OFDM entry of struct rtw89_txpwr_limit
by using the value corresponding to primary channel.
E.g. center channel 38 (40Mhz bandwidth case)
Originally OFDM entry was filled by value corresponding to 'ch - 2' (36)
Now, we consider that it could be 36 or 40.
E.g. cneter channel 42 (80Mhz bandwidth case)
Originally OFDM entry was filled by value corresponding to 'ch - 6' (36)
Now, we consider that it could be 36, 40, 44, or 48.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220218034042.9218-1-pkshih@realtek.com
Add declarations of 6G stuff and extend rtw89_channel_to_idx() to
map 6G's channels to 6G channel indexes. While 6G, correspondingly
read 6G's entry for tx power limit and limit_ru.
After this, we should pay attention to chip_info::support_bands.
If a chip declares 6G support, it must configure txpwr_lmt_6g and
txpwr_lmt_ru_6g in case accessing NULL pointer while setting tx power
limit/limit_ru on 6G band.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220218034017.9160-2-pkshih@realtek.com
Apply 160M bandwidth to RA (rate adaptive) mechanism, so it can transmit
packets with this bandwidth. On the other hand, convert 160M bandwidth
from RX desc to rx_info_bw.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220211075953.40421-7-pkshih@realtek.com
Split 6G band into 8 sub-bands where indexes are from 0 to 7,
i.e. RTW89_CH_6G_BAND_IDX[0-7]. Then, decide subband by both
band and channel instead of just channel because conflicts
between 5G channels and 6G channels.
Moreover, add default case to the existing use of switch (subband).
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220211075953.40421-4-pkshih@realtek.com
Since these macro in rfk helpers are common now, a common naming
should be better. So, apply RTW89_ as prefix to them, and modify
the use correspondly. No logic is changed at all.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220211075953.40421-3-pkshih@realtek.com
These rfk helpers are also useful for the chip which is under planning.
So, move them to common code to avoid duplicate stuff in the future.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220211075953.40421-2-pkshih@realtek.com
B_AX_PLT_EN is to enable polluted mechanism. If it is enabled and
gnt_bt = 1 while wlan TX, B_AX_BT_PLT_PKT_CNT counter will increase,
but TX counter to BB will not. Without this bit BTCoex mechanism might
have some problems.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220208082751.43553-1-pkshih@realtek.com
Some APs like CMW270 only support one phyrate and the function
rtw89_phy_ra_mask_rssi could disable that rate. To fix such problem, we
restore the rate mask if we find that the rate_mask is empty.
Also, apply missed legacy rates from sta->supp_rates[].
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220208082427.42433-3-pkshih@realtek.com
Configure firmware and hardware to run AP mode. The start_ap() setup
bssid, mac port, mac_id entry, and does RFK. The stop_ap() reset the
state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-6-pkshih@realtek.com
In AP mode, when a STA associate to us, we need to create an entry in
firmware and hardware, and then they can transmit data properly.
The entry index called mac_id which is assigned when sta_add, and we ask
firmware to create an entry for an associated station. Also, the address
CAM should be filled so hardware can know which packet is ours, and lookup
the mac_id for further use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-5-pkshih@realtek.com
vif_type mapping indicates hardware operating mode corresponding to vif
type. In STA mode, hardware mode should be INFRA or NO_LINK mode
dynamically according to association status. Since AP mode don't need to
change this by association status intuitively, just do the mapping in
STA mode.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-4-pkshih@realtek.com
In AP mode, each connected station needs an entry of address CAM. The
address CAM of vif is still needed to assit in AP itself.
For station mode, it still uses vif's address CAM.
Add a help macro rtw89_get_addr_cam_of() to get addr_cam from vif or sta
for all use cases.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-3-pkshih@realtek.com
Fill mac_id and self_role depends on the operation mode.
In AP mode, echo connected station has an unique mac_id, and each vif also
has one mac_id to represent itself.
The self_role is assigned to vif if the operation mode is decided, and
RTW89_SELF_ROLE_AP_CLIENT is assigned to the connected STA in AP mode,
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-2-pkshih@realtek.com
In the past we use dbi function of wifi mac to read/write
pci config space, but the function will be remove in new
chip. So use kernel api pci_read/write_config_byte instead.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220121075555.12457-2-pkshih@realtek.com
DIG, which is short for dynamic initial gain, is used to adjust gain to get
good RX performance. CCK PD feature, a mechanism that adjusts 802.11b CCK
packet detection(PD) power threshold based on environment noisy level in
order to avoid false alarm. Also, refine related variable naming.
Signed-off-by: Johnson Lin <johnson.lin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220121075555.12457-1-pkshih@realtek.com
Call to dle_dfi_qempty might fail, leaving qempty.qempty untouched, which
is latter used to control the for loop. If that happens, it's not
initialized anywhere.
Initialize it so the loop doesn't iterate unless it's modified by the
call to dle_dfi_qempty.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220113094253.73370-1-ihuguet@redhat.com
Make stuffs related to channel be collected in channel_params,
and encapsulate the corresponding decision in get_channel_params().
Then, functions that takes channel_params can also notice subband type.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220113011042.6705-2-pkshih@realtek.com
For next chipset which can support 6G band, we add the handling
of ieee80211_supported_band for 6G band in advance. And a bitmap,
support_bands, is added to rtw89_chip_info to declare which
NL80211_BAND_* are supported. With the chipset's declaration,
we register the corresponding instances of ieee80211_supported_band
with wiphy.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220113011042.6705-1-pkshih@realtek.com
One mac_id is corresponding to one connected station, and port ID is a
ID of virtual interfaces. With proper mac_id and port ID, firmware and
hardware can handle a packet with correct context.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-12-pkshih@realtek.com
If a packet we are going to send is broadcast/multicast and certain STAs
are in sleep mode, a flag IEEE80211_TX_CTL_SEND_AFTER_DTIM is added to
txinfo. Then, this kind of packets must be sent via HIQ instead of regular
AC queues, because they should be sent right after beacon.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-11-pkshih@realtek.com
HIQ is short for high queue that is used to send broadcast/multicast
packets right after TBTT in AP mode. Two registers, DTIM and window size,
are configured accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-10-pkshih@realtek.com
The H2C_FUNC_MAC_FWROLE_MAINTAIN also maintains the roles of all connected
stations; not just the role of VIF. So, I correct the name, but don't
change the logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-9-pkshih@realtek.com
The h2c_join firmware command is used to indicate a station is connected,
and the assoc_cmac_tbl firmware command is used to set CMAC table
corresponding to a mac_id. Both commands must work in both station and AP
modes. Use the mac_id of rtw89_sta naturally and intuitively.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-8-pkshih@realtek.com
In station mode, mac_id of station is the same as rtwvif's one.
In AP mode, each station uses individual mac_id.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-7-pkshih@realtek.com
Update beacon content if TIM bitmap maintained by mac80211 is changed.
Since .set_tim must be atomic but driver uses mutex lock, we add a work.
Otherwise, kernel says "sched: RT throttling activated" and lock down.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-6-pkshih@realtek.com
This C2H notify driver the beacon count we send out. We don't handle the
content for now, so add a dummy handler to avoid messages, like
rtw89_pci 0000:03:00.0: c2h class 0 func 3 not support
C2H: 00000000: 01 03 01 3f 0f 00 00 00 80 0a 00 00 00 00 a0
rtw89_pci 0000:03:00.0: c2h class 0 func 3 not support
C2H: 00000000: 01 03 01 40 0f 00 00 00 00 03 20 00 00 00 a5
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-5-pkshih@realtek.com
Firmware sends out beacon content generated by mac80211, and then stations
can receive beacon and work with this AP properly. Also, we download
beacon content again if TIM is changed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-4-pkshih@realtek.com
Since firmware transmits beacon by hardware SSN, driver does it with the
same setting, then packets in the air have continual sequence number.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-3-pkshih@realtek.com
BA CAM is used to ACK peer's packets, so it must be established when
IEEE80211_AMPDU_RX_START, and free it by IEEE80211_AMPDU_RX_STOP.
The hardware can support two static BA CAM entries, so I implement a bitmap
and a struct to record which entry is used and its corresponding tid. Also,
the hardware can learn and create dynamic BA CAM entries automatically if
received packets don't match static BA CAM. That means it can still work if
we don't use H2C to set static BA CAM. An exception is tid=0 should be
always allocated in static BA CAM, so an existing static BA CAM will be
replaced if it is full and peer is going to establish a BA with tid=0.
The new firmware use new format of this H2C, so I upgrade it as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220104012052.6911-1-pkshih@realtek.com
We have three points to receive packets to mac80211 with three different
kinds of status. Many handlers are common and can be shared, so I move
them together, and I don't change the logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220103013623.17052-3-pkshih@realtek.com
