No longer access chan with hard-code RTW89_CHANCTX_X whenever possible.
Instead, obtain the right chanctx from somewhere and use it in RTL8852C
RFK (RF calibration) related code.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240819091724.33730-6-pkshih@realtek.com
DPK is one kind of RF calibration. When MCC (multi-channel concurrency)
start/stop, DPK needs to do extra things to be off/on. We add a chanctx
callback type, RTW89_CHANCTX_CALLBACK_RFK, and register it for RTL8852C
to deal with DPK according to MCC states.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-4-pkshih@realtek.com
Introduce struct rtw89_chan ahead to encapsulate stuffs from struct
rtw89_channel_params. These stuffs have a clone in HAL and are used
throughout driver. After multiple channels support, it's expected that
each channel instance has a configuration of them. So, we refine them
with struct rtw89_chan by precise type first, and will re-arrange HAL
by struct rtw89_chan in the following as well.
(No logic has changed.)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-3-pkshih@realtek.com
RX DCK is receiver DC calibration. To keep good RF performance, do this
calibration again if the delta of thermal value from the last calibration
is more than 8.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220520071731.38563-5-pkshih@realtek.com
The commit 16b44ed0ff ("rtw89: add RF H2C to notify firmware") is to
add firmware command, and this commit is to prepare the channels. Then,
firmware can get proper channels.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-2-pkshih@realtek.com
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
8852c needs two backup buffers, so we enlarge the array. But, 8852a still
needs only one, so it only uses first element (index zero).
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-9-pkshih@realtek.com
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-8-pkshih@realtek.com
RX DCK is receiver DC calibration. Do this calibration when bringing up
interface and going to run on AP channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-7-pkshih@realtek.com
RCK is synchronize RC calibration. It needs to be triggered only once when
interface is going to up.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-6-pkshih@realtek.com
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.
To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-5-pkshih@realtek.com
LCK is short fro LC Tank calibration. Do this calibration once driver
loads RF parameters table. Since the characteristic can be changed by
temperature, we do this calibration again if difference of thermal value
is over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-4-pkshih@realtek.com
DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output analog signals as expected.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-3-pkshih@realtek.com
