Since chips could use different version of BA CAM H2C command, add a
chip_ops to abstract the operation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091134.67007-4-pkshih@realtek.com
WiFi 7 chips use different bb_gain_info struct, so move existing struct to
a union in advance. This doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240105064228.36580-2-pkshih@realtek.com
To activate SER (system error recovery) in firmware, we have to configure
IMR to trigger interrupts, and then SER can check registers to know if it
need to reset hardware or notify driver to re-configure whole settings.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-4-pkshih@realtek.com
In queue empty check, one group contains 32 queues. And, the two elements,
wde_qempty_acq_num and wde_qempty_mgq_sel, are number of group and select
of group. To avoid confusing them with queue number and queue selection,
we refine their naming.
(don't change logic at all)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124071703.132549-5-pkshih@realtek.com
Add dynamic mechanism EDCCA (Energy Detection Clear Channel Assessment)
in track work. Using a fixed-value threshold will make EDCCA particularly
sensitive and cause failure to transmit under certain circumstances.
Therefore, the threshold is dynamically adjusted to make EDCCA suitable
for any situation.
However, in some cases, we will adjust the EDCCA threshold to the highest
level so that urgent transmissions can be performed successfully, such as
scanning.
Finally, in order to observe the EDCCA report in time, add the EDCCA perIC
register macro and EDCCA HW report analysis. EDCCA logs can be displayed
by using the EDCCA debug mask.
Signed-off-by: Yi-Chen Chen <jamie_chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231122060458.30878-3-pkshih@realtek.com
Read calibration values of RX gain offset from efuse, and set them to
registers to normalize RX gain for all hardware modules. Then, PHY dynamic
mechanism can get expected values to adjust hardware parameters to yield
expected performance.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231117024029.113845-5-pkshih@realtek.com
MAC address, hardware type, calibration values and etc are stored in efuse,
so we read them at probe stage and use them as capabilities to register
hardware.
There are two physical efuse -- one is the main efuse for digital hardware
part, and the other is for analog part. Because they are very similar, we
only describe the main efuse below.
The main efuse is split into two regions -- one is for logic map, and the
other is for physical map. For both regions, we use the same method to read
data, but need additional parser to get logic map. To allow reading
operation, we need to convert power state to active, and turn to idle state
after reading.
For WiFi 7 chips, we introduce efuse blocks to define feature group easier,
and these blocks are discontinue. For example, RF block is from 0x1_0000 ~
0x1_0240, and the next block PCIE_SDIO is starting from 0x2_0000.
Comparing to old one used by WiFi 6 chips, there is only single one logic
map, it would be a little hard to add an new field to a group if we don't
reserve a room in advance.
The relationship between efuse, region and block is shown as below:
(logical map)
+------------+ +---------------+ +-----------------+
| main efuse | | region 1 | | block 0x1_0000~ |
| (digital) | |(to logcal map)| +-----------------+
| | | | => +-----------------+
| | => | | | block 0x2_0000~ |
| | | | +-----------------+
| | |---------------| :
| | | region 2 |
+------------+ +---------------+
+------------+ +-----------------+
| 2nd efuse | ======================> | block 0x7_0000~ |
| (analog) | +-----------------+
+------------+
The parser converting from raw data to logic map is to decode block page,
block page offset, and word_en bits. Each word_en bit indicates two
following bytes as data of logic map, so total four word_en bits can
represent eight bytes. Thus, block page offset is 8-byte alignment.
The layout of a tuple is shown as below
+--------+--------+--------+--------+--------+--------+
| fixed 3 byte header | | | |
| | | | |
| [19:17] block_page | | | ... |
| [16:4] block_page_offset| | | |
| [3:0] word_en | ^ | ^ | |
+----|---+--------+--------+---|----+----|---+--------+
| | |
+-------------------------+---------+
a word_en bit indicates two bytes as data
For example,
block_page = 0x3
block_page_offset = 0x80 (must 8-byte alignment)
word_en = 0x6 (b'0110; 0 means data is presented)
following 4 bytes = 34 56 78 90
Then,
0x3_0080 = 34 56
0x3_0086 = 78 90
A special block page is RTW89_EFUSE_BLOCK_ADIE (7) that uses different
but similar format, because its real efuse size is smaller than main efuse.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231117024029.113845-4-pkshih@realtek.com
Different chip can support different max user in one PPDU report.
So, we now configure it in chip info.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231027015059.10032-3-pkshih@realtek.com
The register fields of BSS color map and valid bit are in the same register
for existing chips, but coming WiFi 7 chips define another register to
set valid bit, so add a field to chip_info to reuse the code.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231016065115.751662-3-pkshih@realtek.com
Change naming to disambiguate the functions because their names are common
and not clear about the purpose. Not change logic at all.
These functions are to control baseband AGC while BT coexists with WiFi.
Among these functions, ctrl_btg_bt_rx is used to control AGC related
settings, which is affected by BT RX, while BT shares the same path
with wifi; ctrl_nbtg_bt_tx is used to control AGC settings under
non-shared path condition, which is affected by BT TX.
Signed-off-by: Chung-Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231016065115.751662-2-pkshih@realtek.com
This improves 160MHz performance degradation with certain APs.
Some ICs transmit preamble that are hard to decode by others, continuous
retries then yield low throughput. Fix it with pre-calculated antenna
matrices.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230929004024.7504-3-pkshih@realtek.com
Rename support_ul_tb_ctrl to waveform_ctrl since we need to do more
trigger based control and the naming could be confusing. Move related
code to leaf function so we make each functions separate and can be
easier to maintain.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230929004024.7504-2-pkshih@realtek.com
We are going to allow RTL8852C to support MCC (multi-channel concurrency).
So, we increase 8852c::support_chanctx_num up to 2.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230921003559.11588-4-pkshih@realtek.com
The following are introduced for Wi-Fi 7 chips.
1. take BW/OFDMA into account on TX power by rate
2. increase TX power offset types up to EHT
3. split TX shape into tx_shape_lmt and tx_shape_lmt_ru
If functions which are only for AX, they always access TX power by rate
with BW/OFDMA = 0/0, and they don't access tx_shape's lmt_ru section.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230920074322.42898-7-pkshih@realtek.com
For next-generation chips, TX power by rate table comes from RFE (RF
front end) parameter. It can be different according to RFE type. So,
we indicate TX power by rate table inside RFE parameter ahead. For
current chips, even with different RFE types, a chip is configured
with a single TX power by rate table. So, this commit doesn't really
affect these currently supported chips.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230920074322.42898-4-pkshih@realtek.com
For next-generation chips, TX shape table comes from RFE (RF front end)
parameter. It can be different according to RFE type. So, we indicate
TX shape table inside RFE parameter ahead. For current chips, even with
different RFE types, a chip is configured with a single TX shape table.
So, this commit doesn't really affect these currently supported chips.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230920074322.42898-3-pkshih@realtek.com
For existing chips, size of TX WD info is 6 words, but upcoming WiFi 7
chips become 8 words, so add a chip_info to reuse the code.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230911082049.33541-5-pkshih@realtek.com
DPK is one kind of RF calibration. When MCC (multi-channel concurrency)
start/stop, DPK needs to do extra things to be off/on. We add a chanctx
callback type, RTW89_CHANCTX_CALLBACK_RFK, and register it for RTL8852C
to deal with DPK according to MCC states.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-4-pkshih@realtek.com
Though WiFi 7 chips need BB MCU firmware, we don't download it in probe
stage. Instead, only bring interface up under normal operation or WoWLAN
mode. So, add an argument to assist download flow to setup download
settings properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-6-pkshih@realtek.com
TSSI configures bandedge to TX proper waveform, these new bandedge
parameters improve the accuracy of transmit power compensation.
This helps to avoid throughput degradation.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230830092849.153251-2-pkshih@realtek.com
The ENV_MNTR(environment monitor) is the dynamic mechanism which based on
the HW of CCX(Cisco Compatible Extensions) which provide the channel
loading and noisy level indicator to debug or support the 802.11k. The
PHYSTS provide the detail PHY information per packet we received for
debugging. The DIG(dynamic initial gain) is the dynamic mechanism to
adjust the packet detect power level by received signal strength to avoid
false detection of the WiFi packet.
The address of registers used for ENV_MNTR, PHYSTS and DIG of WiFi 7 IC
are different with WiFi 6 series, so we modify the method to access the
register address in order to compatible with all WiFi 7 and 6 ICs.
Signed-off-by: Cheng-Chieh Hsieh <cj.hsieh@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-7-pkshih@realtek.com
cr_base is base address of PHY control register. The base of WiFi 6 and 7
chips are 0x1_0000 and 0x2_0000 respectively, so define them accordingly.
For example, if PHY address is 0x1330, absolute address is 0x1_1330 for
WiFi 6 chips, and 0x2_1330 for WiFi 7 chips.
Meanwhile, there are two copies of PHY hardware named PHY0 and PHY1. The
offset between them is 0x2_0000, so the base address of PHY0 and PHY1 are
0x2_0000 and 0x4_0000 respectively.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-6-pkshih@realtek.com
There are two copies of MAC hardware called band0 and band1. Basically,
the only difference between them is base address, so we can share functions
with a 'band' (or 'mac_idx') argument.
The offset of base address of WiFi 6 and 7 are 0x2000 and 0x4000
respectively, so add band1_offset field to new introduced struct
mac_gen_def to possibly reuse functions.
Using below spatch script to convert callers:
@@
expression reg, band;
@@
- rtw89_mac_reg_by_idx(reg, band)
+ rtw89_mac_reg_by_idx(rtwdev, reg, band)
@@
expression reg, port, band;
@@
- rtw89_mac_reg_by_port(reg, port, band)
+ rtw89_mac_reg_by_port(rtwdev, reg, port, band)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-2-pkshih@realtek.com
WiFi 7 chips doesn't have static const tables defined in driver. If tables
aren't loaded properly from firmware file, driver can get NULL pointer
access exception. One way is to add the checking statements when trying to
access these tables, but I choose to check them right after loading
firmware elements from firmware file, so I don't need to add error handlers
everywhere.
Currently, the needed firmware elements of WiFi 6 chips are all zero, and
coming WiFi 7 chip will need at least BB MCU, parameters of BB and RF.
We will add them after 8922AE is verified.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230801021127.15919-9-pkshih@realtek.com
The coming WiFi 7 chip is 8922AE which uses different hardware rate and
register naming rule. Adding a chip_info::chip_gen field can help to
do things by generations accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-2-pkshih@realtek.com
The next generation chips use different RX descriptor format, so add
a chip_ops to hook suitable handlers. Also, the length of RX descriptor is
different, so add a variable to store the length according to chip and
descriptor content dynamically. Then, the code can be more general.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-2-pkshih@realtek.com
Though 8851BE is a 1x1 chip, but it has two antenna hardware module that
needs additional configuration to help choose antenna we are going to use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-3-pkshih@realtek.com
For realtek regulatory, there are following two kinds of configurations
to determine whether to allow UNII-4 band, i.e. 5.9GHz channels.
1. default setting according to whether chip support it or not
2. evaluate realtek ACPI DSM with RTW89_ACPI_DSM_FUNC_59G_EN (func. 6)
If (1) is false, we won't try (2) and just disallow UNII-4. Otherwise,
if (2) is not supported or returns a non-specific value, we follow the
default setting either. Besides, this commit aims to add decision logic
in rtw89 regulatory. Actually, driver doesn't register UNII-4 yet. That
will be handled by another commit.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508081211.38760-3-pkshih@realtek.com
BA CAM of 8852C has more entries and more fields of H2C, and needs
initialization before using. Due to differences from 8852A/8852B, we name
it as V1 before. However, real V1 of BA CAM is introduced now, so change
it to V0_EXT to avoid confusing with firmware design.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-7-pkshih@realtek.com
Previously, 8852B has smaller FIFO size than others, so I use chip_id to
choose debug_mask before. 8851B has similar design, so add a field to
chip_info as a general expression.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-6-pkshih@realtek.com
Since CFO XTAL registers of 8851B is different from 8852A, add a chip_info
field to define their difference. Other chips use another interface, so
fill NULL to this field.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-5-pkshih@realtek.com
NCTL (nano-controller) is used to assist RF calibration that sends
commands to NCTL so it can reduce IO from driver. 8851B needs additional
settings, so add a table to do things.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-4-pkshih@realtek.com
Correct Bluetooth RSSI count method. The 6dB is the gap between hardware
packet sampled value and real RSSI value.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230412012831.10519-4-pkshih@realtek.com
Chips use similar hardware for path control, but could different
path/antenna configuration. Add these register to monitor, if there are
wrong settings, these register can help to debug.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230412012831.10519-3-pkshih@realtek.com
When Wi-Fi & Bluetooth are both busy at the same time, Wi-Fi need to
enable RX gain to protect Wi-Fi RX RF ability. Without this configure
the interference from Bluetooth will bring a big impact to Wi-Fi RX.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230412012831.10519-2-pkshih@realtek.com
Use primary channel index to determine which 5 MHz mask should be enable.
This mask is used to prevent noise from channel edge to effect CCA
threshold in wide bandwidth (>= 40 MHZ).
Fixes: 1b00e9236a ("rtw89: 8852c: add set channel of BB part")
Fixes: 6b0698984e ("wifi: rtw89: 8852b: add chip_ops::set_channel")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230406072841.8308-1-pkshih@realtek.com
Turn on hardware CFO (central frequency offset) compensation based on IC
capability, and improve digital CFO compensation accuracy by using
more fixed points number.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330132352.13647-1-pkshih@realtek.com
One chip can have different RFE (RF front end) types which we will judge
at runtime. And, different RFE types may use different RF parameter tables.
Though we didn't really meet this case previously, we are going to meet it
on upcoming chip RTL8851B. So, this commit handles parameter tables for
runtime RFE type.
We now encapsulate rtw89_txpwr_rule_<2/5/6>ghz tables into rtw89_rfe_parms.
Then, each chip defines its default parameter tables, and if needed, it can
configure extra parameter tables by RFE type. Finally we determine runtime
parameter tables by RFE type if one is configured. Otherwise, we use the
default parameter tables.
For now, we just move all settings under default parameter tables. We will
configure parameter tables by RFE types in separate commits afterwards.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330080331.37155-1-pkshih@realtek.com
In the discuss threads [1] [2], new firmware format break user space
because older drivers can't recognize new firmware format. To avoid this,
the new format will be named rtw89/rtw8852b_fw-1.bin and only new driver
try to load it. Old drivers only load original and understandable firmware
rtw89/rtw8852b_fw.bin.
More, new driver will be still backward compatible with old firmware, so
original firmware can be used by new driver.
If there is newer firmware format is introduced, rtw89/rtw8852b_fw-2.bin
will be given. The same rules will be applied like above. So, we will have
firmware like below in linux-firmware in the future.
rtw89/rtw8852b_fw-2.bin
rtw89/rtw8852b_fw-1.bin
rtw89/rtw8852b_fw.bin
After this patch, MODULE_FIRMWARE() of 8852A/B/C become
rtw89/rtw8852a_fw.bin
rtw89/rtw8852b_fw-1.bin
rtw89/rtw8852c_fw.bin
[1] https://lore.kernel.org/linux-wireless/df1ce994-3368-a57e-7078-8bdcccf4a1fd@gmail.com/T/#m24cb43be31a762d0ea70bf07f27ae96c59f6931b
[2] https://bugzilla.kernel.org/show_bug.cgi?id=217207
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320130606.20777-4-pkshih@realtek.com
Need to configure EDCCA threshold to default value before scan, and recall
original value after scan to prevent probe request can't be sent out.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230322060238.43922-1-pkshih@realtek.com
The register-based H2C/C2H are used to exchange information between driver
and firmware, but only apply to narrow area because its data size is
smaller than regular packet-based H2C/C2H.
This kind of H2C/C2H must be paired. To identify if any H2C/C2H is missing,
update counters to help diagnose this kind of problems.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230316063956.71687-1-pkshih@realtek.com
The LNA gain didn't set before, it will lead some WiFi RX issue.
And the setting can increase both of WiFi & BT performance while
they are both RX.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230314020617.28193-4-pkshih@realtek.com
Since the range of channel table is identical among ICs. Make channel
encode/decode function common and not IC dependent. So all ICs with
matching firmware that needs this kind of coding can use it directly.
This patch doesn't change logic at all.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230220070202.29868-4-pkshih@realtek.com
In path of setting channel and setting TX power, the rtw89_chan instance
to be used is controlled by top and passed down. The set_tx_shape_dfir()
is in path of setting TX power, so it should use the passed rtw89_chan
instead of querying it itself. Otherwise, it might encounter mismatch
between parameters if multi-channel.
For example,
rtw89_8852ce 0000:04:00.0: set tx shape dfir by unknown ch: 155 on 2GHz
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230201032057.7349-1-pkshih@realtek.com
New firmware type NORMAL_CE is introduced to support P2P-PS and hardware
scan, but no LPS-PG mode. After this patch, old firmware with NORMAL type
can still work well.
The use of this new type is the same as before, so we add new type to
avoid taking wrong firmware. Then, driver log can also give clear
information about this change:
rtw89_8852be 0000:03:00.0: Firmware version 0.29.26.0, cmd version 0, type 5
rtw89_8852be 0000:03:00.0: Firmware version 0.29.26.0, cmd version 0, type 3
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230123065401.14174-7-pkshih@realtek.com
BSS color mapping register is different per IC, therefore, move this
register to chip_info and update the setting function. Without this patch,
wrong BSS color causes behavior abnormal, especially DL-OFDMA.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221214091803.41293-1-pkshih@realtek.com
Previous patch has added format version derived from firmware version.
Use the format version, and remove constant version number from chip_info.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221217141745.43291-3-pkshih@realtek.com
The `rtw89_mcc_info mcc` is only for RFK MCC stuffs instead of common
MCC management info. Replace it with `rtw89_rfk_mcc_info rfk_mcc` to
avoid confusion and reserve `struct rtw89_mcc_info mcc` for MCC management
code.
(No logic changes.)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221129083130.45708-2-pkshih@realtek.com
There are some registers for transmit waveform control, two of them used
in this change are for BANDEDGE and TX_SHAPE control. BANDEDGE controls
whether to apply band edge filter to transmit waveform. TX_SHAPE controls
whether to apply triangular mask to transmit waveform. It is found for
some chip, these two should be turned off during OFDMA UL traffic for
better performance.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117063001.42967-3-pkshih@realtek.com
Add macro to get FD(frequency domain) CFO field from ie_type 1, and correct
the naming for preamble CFO field. Each IC could assign the CFO source to
either FD CFO or preamble CFO in chip_info. Based on the suggestion from HW
designer, rtw8852b and its derived versions will have better CFO tracking
performance with FD CFO.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117063001.42967-2-pkshih@realtek.com
Pattern match is an option of WoWLAN to allow the device to be woken up
from suspend mode when receiving packets matched user-designed patterns.
The patterns are written into hardware via WoWLAN firmware in suspend
flow if users have set up them. If packets matched designed pattern are
received, WoWLAN firmware will send an interrupt and then wake up the
device.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-8-pkshih@realtek.com
WoWLAN is a feature which allows devices to be woken up from suspend
state through WLAN events.
When user enables WoWLAN feature and then let the device enter suspend
state, WoWLAN firmware will be loaded by the driver and periodically
monitors WiFi packets. Power consumption of WiFi chip will be reduced
in this state.
We now implement WoWLAN function in rtw8852ae and rtw8852ce chip.
Currently supported WLAN events include receiving magic packet,
rekey packet and deauth packet, and disconnecting from AP.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-7-pkshih@realtek.com
When entering WoWLAN mode, we need to drop all transmit packets,
including those in mac buffer, to avoid memory leakage, so implement
the drop_tx function.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-5-pkshih@realtek.com
The gain tables use different domain index, so we need to convert the index
from subband of chandef. Since these conversion functions can share with
8852b, make generic functions for further use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-6-pkshih@realtek.com
This chunk is to set fixed BT LNA2 at level5 when WiFi/BT shared BTG RFC
to improve BT anti-interference ability from adjacent channel. Since all
chips use the same setting, remove chip_ops::btc_bt_aci_imp.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-2-pkshih@realtek.com
8852CE is a combo chip, and WiFi driver controls pin MUX. To output BT
firmware log to specific hardware pin, set pin MUX to achieve.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220930134417.10282-1-pkshih@realtek.com
Previously, we thought control registers or setting things for TX power
series may change according to chip. So, setting functions are implemented
chip by chip. However, until now, the functions keep the same among chips,
at least 8852A, 8852C, and 8852B. There is a sufficient number of chips to
share generic setting functions. So, we now remake them including TX power
by rate, TX power offset, TX power limit, and TX power limit RU as generic
ones in phy.c.
Besides, there are some code refinements in the generic ones, but almost
all of the logic doesn't change.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220928084336.34981-5-pkshih@realtek.com
Implement to power on/off BB and RF via MAC registers.
Add return type of chip_ops::disable_bb_rf, because it could fail to
disable. Also, correct naming of register 0x0200 used by the ops as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220927062611.30484-5-pkshih@realtek.com
Six channels are unsupported by 8852b, so mask them out to prevent to
access undefined registers in this chip.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220927062611.30484-3-pkshih@realtek.com
Since we maintain coexistence as shared code, so move coexistence version
from chip specific attribute to a definition.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220920010939.12173-10-pkshih@realtek.com
To prevent LNA2 change its gain during a Wi-Fi aggregation packet while
GNT_BT pull high. Otherwise, changes of this gain will destroy the whole
aggregation when Wi-Fi RX.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220920010939.12173-7-pkshih@realtek.com
Because RTL8852A/RTL8852C use different firmware buffer size to
send C2H packet, it's necessary to use different size to parse C2H report.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220913092546.43722-4-pkshih@realtek.com
rtw8852c could support deep ps mode if the firmware version
is greater than 0.17.34.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-7-pkshih@realtek.com
With suitable response rate, it can acknowledge peer packets are received.
Otherwise, peer could re-transmit again due to missing of ACK frames.
To achieve this, refer to RX rate and CMAC table to choose the smaller
as initial response rate.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-6-pkshih@realtek.com
With one path TX for 1SS rate, it can transmit higher power in 6GHz band
to yield better performance in high attenuation circumstance.
Signed-off-by: Yi-Tang Chiu <chiuyitang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-5-pkshih@realtek.com
Enable MU-MIMO interference cancellation (MUIC) to yield expected
performance of receiving MU-MIMO packets on 6GHz.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-3-pkshih@realtek.com
Since control register address for DIG are different per IC, add a new
struct rtw89_dig_regs in chip info for each IC to define their own address.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908051257.25353-2-pkshih@realtek.com
Originally, we show average signal strength. To support TX diversity, this
patch prepares strength per path, then we can decide TX path.
RSSI: -54 dBm (raw=112, prev=110) [-57, -52]
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908074140.39776-5-pkshih@realtek.com
The bacam_v1 must do additional initialization, and H2C content of BA CAM
is also different. So, correct them accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220816013247.6243-3-pkshih@realtek.com
8852A has 2 BA CAM entries, but 8852C has 8 entries. Add a field to
discriminate their differences.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220816013247.6243-2-pkshih@realtek.com
Some chips' RF TX power limit/limit_ru tables start to configure some
negative values. Fix the setting logic to prevent negative values from
polluting fields of others.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220812093116.56791-2-pkshih@realtek.com
Due to the difference of Wi-Fi firmware supported feature, RTL8852C
need to defined more policy to enable the features.
(Ex: DBCC, Wi-Fi multi-role, TDMA instant and so on)
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-8-pkshih@realtek.com
Add a part of logic to parse type of ctrl report from firmware, and
remove Bluetooth packet counter count from driver, the feature was
moved to firmware at rtl8852c.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-4-pkshih@realtek.com
To configure the different chips with different coexistence version,
separated the firmware feature version matching number is necessary.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220725023509.43114-3-pkshih@realtek.com
In current flow, FW is asynchronously loaded after alloc_hw(). It defers
the decision on FW feature map. It makes things difficult for us to decide
whether to hook chanctx ops, which should be decided while alloc_hw() is
calling. Still, asynchronous gets its advantages. So, we want to resolve
this without dropping them.
Based on multi-FW flag, RTW89_MFW_SIG, we can determine runtime FW is
multi-FW (MFW) or single FW (SFW). Both of them have a quite small chunk
for header at the head. The difference is that MFW doesn't describe version
code in its header while SFW does. So, we plan to extend MFW header for
version code. After that, in both cases, we can determine FW feature map by
just FW header. And, according to the map, we can decide chanctx.
So, we call request_partial_firmware_into_buf() to request a quite small
chunk before alloc_hw() to get a early FW feature map without affecting
things much and only use early map to decide whether to hook chanctx ops.
It means that if non-extended MFW is used at runtime, driver just acts
without chanctx as before. If extended MFW or SFW, which supports required
FW features, is used at runtime, driver can hook chanctx ops to mac80211 if
chip has configured support_chanctx_num > 0.
Besides, key point for now to support single one chanctx is whether HW scan
is supported at runtime. So, we configure all chip's support_chanctx_num to
1, and check if HW scan is supported at runtime via early FW feature map.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-14-pkshih@realtek.com
Some HW features are required if we hook chanctx ops to mac80211. With it,
mac80211 would expect the HW-supported variant ops exists on some behavior,
e.g. HW scan. But, HW features may depend on chip's FW or its development.
Besides, how many chanctx can be supported also depends on chip design.
We can neither decide whether to generally support chanctx ops nor how many
chanctx can be supported.
So, support_chanctx_num is added under chip info to deal with this by chip.
For now, all chip configure support_chanctx_num as 0. We haven't really
hook chanctx ops yet. So, chip can run without mac80211 chanctx as before.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-13-pkshih@realtek.com
For future support on multiple channels by multiple sub-entities,
we need to manage parameters of each channel instance like rtw89_chan,
rtw89_mac_idx, rtw89_phy_idx. So, we adjust related channel callback
functions and centrally conrtol these parameters in set_channel().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-8-pkshih@realtek.com
For future support on multiple channels, there will be settings of
multiple sub-entities that we need to control. We don't want such
settings to be scattered all over the place. So, we centrally manage
controls of rtw89_phy_idx for RFK in set_channel().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-7-pkshih@realtek.com
For future support on multiple channels, it would be disturbing if we
still allow scattered leaf functions of TX power to query and manage
channel related control by themselves.
So, query rtw89_chan only on top functions. Then, pass it via functions
to make sure that the values coming from the same struct rtw89_chan.
Besides, fix rtw8852a_set_txpwr_offset() from rtw8852a_set_txpwr_ctrl()
to rtw8852a_set_txpwr(). TX power offset should consider current band,
so move it to chip_ops::set_txpwr() which will be called every time that
channel is set.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-6-pkshih@realtek.com
We are planning to support mac80211 chanctx. To reduce future works,
the driver architecture is adjusted first to isolate related things.
According to chip, our HW may have multiple sub-entities to support
multiple mac80211 chanctx. Struct rtw89_chan has been introduced for
things about channel/band/subband/... Now introduce struct rtw89_chan_rcd
to record difference after assigning new one of struct rtw89_chan.
We will implement and support chanctx with single channel first, i.e.
only use entry in RTW89_SUB_ENTITY_0, before handling dual channels.
Our hierarchy in planning will become as the following.
DEV
-> HAL
---> entity (manage status across sub-entities)
-----> sub-entity[*] (support mac80211 chanctx)
where each sub-entity contains one struct rtw89_chan.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-4-pkshih@realtek.com
Introduce struct rtw89_chan ahead to encapsulate stuffs from struct
rtw89_channel_params. These stuffs have a clone in HAL and are used
throughout driver. After multiple channels support, it's expected that
each channel instance has a configuration of them. So, we refine them
with struct rtw89_chan by precise type first, and will re-arrange HAL
by struct rtw89_chan in the following as well.
(No logic has changed.)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-3-pkshih@realtek.com
RX DCK is receiver DC calibration. To keep good RF performance, do this
calibration again if the delta of thermal value from the last calibration
is more than 8.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220520071731.38563-5-pkshih@realtek.com
To make user space can set TX antenna via iw command. Then, we can diagnose
antenna is connected properly or not, and measure TX power in single path.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-3-pkshih@realtek.com
Modify NBI and PD boost settings according to different primary channels.
This setting can decrease the false alarm induced by DC.
Signed-off-by: Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-2-pkshih@realtek.com
The chip_info include BT coexistence tables, size and number of hardware
components, and supported functions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-4-pkshih@realtek.com
The commit 16b44ed0ff ("rtw89: add RF H2C to notify firmware") is to
add firmware command, and this commit is to prepare the channels. Then,
firmware can get proper channels.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-2-pkshih@realtek.com
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
8852c needs two backup buffers, so we enlarge the array. But, 8852a still
needs only one, so it only uses first element (index zero).
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-9-pkshih@realtek.com
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-8-pkshih@realtek.com
RX DCK is receiver DC calibration. Do this calibration when bringing up
interface and going to run on AP channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-7-pkshih@realtek.com
RCK is synchronize RC calibration. It needs to be triggered only once when
interface is going to up.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-6-pkshih@realtek.com
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.
To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-5-pkshih@realtek.com
LCK is short fro LC Tank calibration. Do this calibration once driver
loads RF parameters table. Since the characteristic can be changed by
temperature, we do this calibration again if difference of thermal value
is over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-4-pkshih@realtek.com
DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output analog signals as expected.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-3-pkshih@realtek.com
Eliminate the following coccicheck warning:
./drivers/net/wireless/realtek/rtw89/rtw8852c.c:2556:2-3: Unneeded
semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220427003142.107916-1-yang.lee@linux.alibaba.com
