To set TX/RX path or set channel, we need these helpers to stop TX and
restore settings. The sch_tx stands for scheduler TX channel, and the
cfg_ppdu is to stop reporting PPDU status, so we should stop them during
setting.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033637.12330-3-pkshih@realtek.com
Be higher resolution of SER timer unit from 32ms to 16ms to detect
abnormal situation more accurately, and set hardware watchdog timer to 4ms.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240121071826.10159-2-pkshih@realtek.com
These functions are to control baseband AGC while BT coexists with WiFi.
Among these functions, ctrl_btg_bt_rx is used to control AGC related
settings, which is affected by BT RX, while BT shares the same path with
WiFi; ctrl_nbtg_bt_tx is used to control AGC settings under non-shared
path condition, which is affected by BT TX.
Signed-off-by: Chung-Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240120003831.7014-7-pkshih@realtek.com
The ::power_trim is to write bias value programmed in efuse to normalize
TX power, and then using ::set_txpwr_ctrl to set reference TX power value.
The ::set_txpwr is to set final TX power according to regulation of current
country.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240120003831.7014-6-pkshih@realtek.com
Firmware H2C commands and C2H events can go via registers, so define them
accordingly. The page registers are to arrange local buffer of WiFi chip.
RRSR is to define rate selection to transmit BA or ACK. EDCCA is to set
threshold of engine detection mechanism by BB hardware.
Like other chips, define these registers and we can share the same flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240120003831.7014-5-pkshih@realtek.com
The chip_ops::bb_preinit and ::bb_postinit are called before and after
loading BB parameters from tables of firmware file. The ::bb_reset is
used to reset hardware state, and currently it is not needed by 8922AE so
leave it as empty. The ::bb_sethw is to implement conditional parameters.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240120003831.7014-4-pkshih@realtek.com
When we are going to up interface to make connection, turn on BB and RF
hardware power by enable_bb_rf ops. Oppositely, using disable_bb_rf to
turn them off.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240120003831.7014-3-pkshih@realtek.com
The channel_info is hardware settings to reflect operational status, such
as scale factor, report unit, buffer matrix size, RU size and so on. Then,
we can get desired reports to do further tuning.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240105064440.36926-1-pkshih@realtek.com
TX power is controlled by BB layer basically, but it should interact with
MAC layer, so these registers are put on MAC register domain and called
BB wrapper, which contains TX power for each MAC ID, OFDMA RU power, and
consideration of power type table.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240105064433.36870-1-pkshih@realtek.com
NCTL standing for nano-controller is used to assist RF calibration.
Basically, we write settings from a table, but format of the table can't
describe register mask and additional conditions, so add a function to
set this kind of settings.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240105064422.36812-1-pkshih@realtek.com
DIG standing for dynamic initial gain that is used to adjust RX coverage,
and PD lower threshold is packet detection power level by received signal
strength to avoid false detection of the WiFi packet.
Because of the hardware is different between WiFi 7 and 6 ICs, we adjust
flow and add register definition for 8922A.
Signed-off-by: Cheng-Chieh Hsieh <cj.hsieh@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240105064228.36580-5-pkshih@realtek.com
After enabling DMAC and CMAC, configure detail registers one by one.
DMAC includes DLE (data link engine), packet preload engine, HFC (HCI
flow control) for DMA channels, security egine and etc. CMAC includes
scheduler, address CAM, RX filter, CCA control and etc.
The SER IMR is to configure to help SER. When hardware TX/RX get
abnormal, it raises an interrupt to firmware to determine if send C2H
events to notify driver to reset PCI bus or call ieee80211_restart_hw().
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231216045739.10432-3-pkshih@realtek.com
The sys_init is to enable hardware function block of DMAC (data-path MAC),
CMAC (control-path MAC) and others called 'chip_func'. To understand the
functionality of this function, we keep some functions as empty.
The other is typ_fltr_opt that is to configure filter option to decide
whether RX packets engine can forward packets to host or WiFi CPU.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231216045739.10432-2-pkshih@realtek.com
The power on/off functions are to turn on hardware function blocks and
to turn off them if we are going to stay in idle state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-3-pkshih@realtek.com
The XTAL SI is a serial interface to indirectly access registers of
analog hardware circuit. Since WiFi 7 chips use different registers, add
a ops to access them via common functions. This patch doesn't change logic
for existing chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-2-pkshih@realtek.com
To diagnose the reason why firmware or hardware get abnormal, add to dump
MAC registers related to counters and interrupt masks. With these values,
people can classify problems and check if registers values are unexpected,
and then correct them. However, it could possible false alarm because
firmware triggers this SER event by wrong conditions that we should
correct it at firmware or register settings.
In field, SER might happen under special conditions, and very hard to
happen again, so dump lots of registers to provide rich information to
catch the problem.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-5-pkshih@realtek.com
To activate SER (system error recovery) in firmware, we have to configure
IMR to trigger interrupts, and then SER can check registers to know if it
need to reset hardware or notify driver to re-configure whole settings.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-4-pkshih@realtek.com
Extend FW program counter dump for Wi-Fi 7 chip.
They poll different addresses.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204080751.15354-3-pkshih@realtek.com
The attempt to enter power save mode might fail if there are still
beacons pending in the queue. This sometimes happens after stopping
P2P GO or AP mode. Extend stop AP function and flush all beacons to
resolve this.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231129070046.18443-2-pkshih@realtek.com
Add functions to configure HCI, DMAC (data MAC), DLE (data link engine),
HFC (HCI flow control), PLE (payload engine) and etc for WiFi 7 chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124071703.132549-9-pkshih@realtek.com
This function, currently called by WoWLAN flow, polls until specific HW
queues are empty. The polling bit definitions are not totally the same
between WiFi 6 and 7 chips. In addition, the check conditions are also
a little different. So, we differentiate the implementations according to
chip gen.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124071703.132549-6-pkshih@realtek.com
Add dynamic mechanism EDCCA (Energy Detection Clear Channel Assessment)
in track work. Using a fixed-value threshold will make EDCCA particularly
sensitive and cause failure to transmit under certain circumstances.
Therefore, the threshold is dynamically adjusted to make EDCCA suitable
for any situation.
However, in some cases, we will adjust the EDCCA threshold to the highest
level so that urgent transmissions can be performed successfully, such as
scanning.
Finally, in order to observe the EDCCA report in time, add the EDCCA perIC
register macro and EDCCA HW report analysis. EDCCA logs can be displayed
by using the EDCCA debug mask.
Signed-off-by: Yi-Chen Chen <jamie_chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231122060458.30878-3-pkshih@realtek.com
MAC address, hardware type, calibration values and etc are stored in efuse,
so we read them at probe stage and use them as capabilities to register
hardware.
There are two physical efuse -- one is the main efuse for digital hardware
part, and the other is for analog part. Because they are very similar, we
only describe the main efuse below.
The main efuse is split into two regions -- one is for logic map, and the
other is for physical map. For both regions, we use the same method to read
data, but need additional parser to get logic map. To allow reading
operation, we need to convert power state to active, and turn to idle state
after reading.
For WiFi 7 chips, we introduce efuse blocks to define feature group easier,
and these blocks are discontinue. For example, RF block is from 0x1_0000 ~
0x1_0240, and the next block PCIE_SDIO is starting from 0x2_0000.
Comparing to old one used by WiFi 6 chips, there is only single one logic
map, it would be a little hard to add an new field to a group if we don't
reserve a room in advance.
The relationship between efuse, region and block is shown as below:
(logical map)
+------------+ +---------------+ +-----------------+
| main efuse | | region 1 | | block 0x1_0000~ |
| (digital) | |(to logcal map)| +-----------------+
| | | | => +-----------------+
| | => | | | block 0x2_0000~ |
| | | | +-----------------+
| | |---------------| :
| | | region 2 |
+------------+ +---------------+
+------------+ +-----------------+
| 2nd efuse | ======================> | block 0x7_0000~ |
| (analog) | +-----------------+
+------------+
The parser converting from raw data to logic map is to decode block page,
block page offset, and word_en bits. Each word_en bit indicates two
following bytes as data of logic map, so total four word_en bits can
represent eight bytes. Thus, block page offset is 8-byte alignment.
The layout of a tuple is shown as below
+--------+--------+--------+--------+--------+--------+
| fixed 3 byte header | | | |
| | | | |
| [19:17] block_page | | | ... |
| [16:4] block_page_offset| | | |
| [3:0] word_en | ^ | ^ | |
+----|---+--------+--------+---|----+----|---+--------+
| | |
+-------------------------+---------+
a word_en bit indicates two bytes as data
For example,
block_page = 0x3
block_page_offset = 0x80 (must 8-byte alignment)
word_en = 0x6 (b'0110; 0 means data is presented)
following 4 bytes = 34 56 78 90
Then,
0x3_0080 = 34 56
0x3_0086 = 78 90
A special block page is RTW89_EFUSE_BLOCK_ADIE (7) that uses different
but similar format, because its real efuse size is smaller than main efuse.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231117024029.113845-4-pkshih@realtek.com
8922A is a 802.11be chip that can support 2/5/6 GHz bands 160MHz bandwidth.
Introduce the basic info such as firmware file name, some hardware address
and size, supported spatial stream, TX descriptor and so on, and then
we can add more attributes by later patches.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231117024029.113845-2-pkshih@realtek.com
The handlers include three parts -- 1) configure interrupt mask;
2) enable/disable interrupt; 3) recognize (read) interrupt status.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231110012319.12727-6-pkshih@realtek.com
For WiFi 7, interrupt status registers and their definitions are changed
a lot, but the logic is still the same, so define fields to reuse the code.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231110012319.12727-5-pkshih@realtek.com
At probe stage, we only do partial initialization to enable ability to
download firmware and read capabilities. After that, we use this pre_deinit
to disable HCI to save power.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231110012319.12727-4-pkshih@realtek.com
PCI LTR (Latency Tolerance Reporting) is a capability to yield expected
power consumption, and we configure the parameters according to design.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-5-pkshih@realtek.com
Call this function when doing MAC initialization at probe stage. It does
partial initial registers only, because we only need basic ability to
download firmware. The function to clear index is the sub-function,
so set its pointer as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-4-pkshih@realtek.com
8922AE is a PCIE 802.11be wireless adapter with PID 0x8922. We add basic
configurations including PCI DMA mode, PCI parameters, register address to
control TX/RX rings and etc.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026120049.9187-2-pkshih@realtek.com
The register address used for CFO(carrier frequency offset) tracking is
different from WiFi 7 series, so we change the way to access it. And we
refine the flow of CFO tracking to compatible all WiFi 7 and 6 ICs.
Signed-off-by: Cheng-Chieh Hsieh <cj.hsieh@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231016065115.751662-4-pkshih@realtek.com
When associated peer has beamformer capability, we should enable
beamformee, set CSI parameter, and configure rate to send CSI packets.
Since registers of WiFi 7 chips are very different from existing chips,
separate configuration functions.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-6-pkshih@realtek.com
When associated peer has beamformer capability, enable hardware beamformee
function, and then hardware can run sounding protocol itself. Oppositely,
disable this function when disassociated. Define different registers for
WiFi 6 and 7 generations respectively.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-5-pkshih@realtek.com
When connected with 802.11ax AP, MU-EDCA parameters are given, so enable
this hardware function by registers according to chip generation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-3-pkshih@realtek.com
When TX size or time of packet over RTS threshold set by this register,
hardware will use RTS protection automatically. Since WiFi 6 and 7 chips
have different register address for this, separate the address according
to chip gen.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-2-pkshih@realtek.com
Wi-Fi 6 chips and Wi-Fi 7 chips have different register design for TX
power RU limit. We rename original setting stuffs with a suffix `_ax`,
concentrate related enum declaration in phy.h, and implement setting
flow for Wi-Fi 7 chips. Then, we set TX power RU limit according to
chip generation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231003015446.14658-6-pkshih@realtek.com
Wi-Fi 6 chips and Wi-Fi 7 chips have different register design for
TX power limit. We rename original setting stuffs with a suffix `_ax`,
concentrate related enum declaration in phy.h, and implement setting
flow for Wi-Fi 7 chips. Then, we set TX power limit according to chip
generation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231003015446.14658-5-pkshih@realtek.com
We have a register to control TX power of each rate section to increase
or decrease an offset. But, Wi-Fi 6 chips and Wi-Fi 7 chips have different
address and format for this control register. We rename original setting
stuffs with a suffix `_ax` and implement setting flow for Wi-Fi 7 chips.
Then, we set TX power offset according to chip generation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231003015446.14658-4-pkshih@realtek.com
Wi-Fi 6 chips and Wi-Fi 7 chips have different register design for
TX power by rate. We rename original setting stuffs with a suffix
`_ax` and implement setting flow for Wi-Fi 7 chips. Then, we set TX
power by rate according to chip generation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231003015446.14658-3-pkshih@realtek.com
There are two difference between Wi-Fi 6 and Wi-Fi 7 chips.
1. Address range of TX power control register
2. Checking code to get a TX power control register
So, separate the implementation of them, access according to
chip generation, and rename original things with a suffix `_ax`.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231003015446.14658-2-pkshih@realtek.com
This improves 160MHz performance degradation with certain APs.
Some ICs transmit preamble that are hard to decode by others, continuous
retries then yield low throughput. Fix it with pre-calculated antenna
matrices.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230929004024.7504-3-pkshih@realtek.com
Using mac_gen pointer to reuse the code with WiFi 7 chips, and define
MAC ports registers for WiFi 7 chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230911082049.33541-7-pkshih@realtek.com
Secure firmware is protected by public/private key cryptography. To help
firmware self verify integrity, configure a heap address for these
data before downloading firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-9-pkshih@realtek.com
To work with generalized flow of download firmware, implement WiFi 7
specific functions to support it. These functions include disable/enable
WiFi CPU, status of path ready, and status of firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-4-pkshih@realtek.com
TSSI configures bandedge to TX proper waveform, these new bandedge
parameters improve the accuracy of transmit power compensation.
This helps to avoid throughput degradation.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230830092849.153251-2-pkshih@realtek.com
The ENV_MNTR(environment monitor) is the dynamic mechanism which based on
the HW of CCX(Cisco Compatible Extensions) which provide the channel
loading and noisy level indicator to debug or support the 802.11k. The
PHYSTS provide the detail PHY information per packet we received for
debugging. The DIG(dynamic initial gain) is the dynamic mechanism to
adjust the packet detect power level by received signal strength to avoid
false detection of the WiFi packet.
The address of registers used for ENV_MNTR, PHYSTS and DIG of WiFi 7 IC
are different with WiFi 6 series, so we modify the method to access the
register address in order to compatible with all WiFi 7 and 6 ICs.
Signed-off-by: Cheng-Chieh Hsieh <cj.hsieh@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-7-pkshih@realtek.com
rx_filter is used to decide which kind of packets are received to driver,
or just dropped by MAC layer to reduce bus traffic.
The bit definitions of old and new chips are the sames, but only address
is changed, so define a field to generalize usage.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-5-pkshih@realtek.com
Define base address of WiFi 7 internal memory according to design to
provide the same functions as existing WiFi 6 chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-4-pkshih@realtek.com
Time Averaged SAR (TAS) tracks the amount of transmit power over a
period of time and adjusts the power accordingly. Two thresholds are
used to determine when to increase or reduce transmit power: Dynamic
Power Reduction (DPR) on/off. Compared to Static SAR, which has a
constant transmit power, TAS can improve the user experience or
range extension.
TAS can be enabled through BIOS, and the driver will evaluate
Realtek ACPI DSM with RTW89_ACPI_DSM_FUNC_TAS_EN to determine
whether TAS should be enabled.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230804053458.31492-1-pkshih@realtek.com
RTL8851B is a chip with only single RF path, and it must use 1 TX power
value for transmission, so force 1 TX power value to prevent hardware
logic gets wrong TX power values randomly in certain samples.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-6-pkshih@realtek.com
LCK is short for LC Tank calibration. To keep RF performance, do this
calibration if difference of thermal value is over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-4-pkshih@realtek.com
We now support RTL8851B which has only single RF path. For chip with
single RF path, TX power page is valid only in single path section.
So, we refine debugfs txpwr table to access TX power page according
to RF path number of runtime chip. It can prevent us from reading
beyond valid sections.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230531060713.57203-3-pkshih@realtek.com
These capabilities include helpers of BT coexistence, RX PPDU status
parser, DIG (dynamic initial gain) and CFO (center frequency offset)
settings.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-3-pkshih@realtek.com
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-3-pkshih@realtek.com
RX DCK is receiver DC calibration. With this calibration, we have proper
DC offset to reflect correct received signal strength indicator. Do this
calibration when bringing up interface and going to run on AP channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-2-pkshih@realtek.com
Set MAC/BB/RF registers according to channel we are going to set. In
additional, certain channels or bands need more deals, such as enable CCK
in 2 GHz band, spur elimination at certain frequencies.
The set channel helper is used to save/restore states before/after setting
channel, and does reset BB to prevent hardware getting stuck in abnormal
state during switching channel and receiving data.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-6-pkshih@realtek.com
Add basic functions to power on chip and enable and access BB/RF, as
well as reset and hardware settings of BB.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-5-pkshih@realtek.com
Though 8851BE is a 1x1 chip, but it has two antenna hardware module that
needs additional configuration to help choose antenna we are going to use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-3-pkshih@realtek.com
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-6-pkshih@realtek.com
DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output good quality signals.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-5-pkshih@realtek.com
Automatic amplitude control calibration (AACK) is the calibration to ensure
the oscillator is biased for a constant output amplitude. We do this
calibration if card does power on.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230424065242.17477-3-pkshih@realtek.com
Since CFO XTAL registers of 8851B is different from 8852A, add a chip_info
field to define their difference. Other chips use another interface, so
fill NULL to this field.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-5-pkshih@realtek.com
Initialize basic antenna switch settings according to hardware module
design, and set to default antenna A. The set antenna function will be
called dynamically to switch antenna according to EVM and RSSI.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418012820.5139-6-pkshih@realtek.com
The function to request DLE (data link engine) buffer uses 'u16' as return
value that mixes error code, so change it to 'int' as regular error code.
Also, treat invalid register value (0xfff) as an error.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414082228.30766-1-pkshih@realtek.com
Many settings of 8851B are the same as 8852B or 8852A, like DLE (Data link
engine), security engine and so on. Update them according to hardware
design.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330133324.19538-4-pkshih@realtek.com
Need to configure EDCCA threshold to default value before scan, and recall
original value after scan to prevent probe request can't be sent out.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230322060238.43922-1-pkshih@realtek.com
The register-based H2C/C2H are used to exchange information between driver
and firmware, but only apply to narrow area because its data size is
smaller than regular packet-based H2C/C2H.
This kind of H2C/C2H must be paired. To identify if any H2C/C2H is missing,
update counters to help diagnose this kind of problems.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230316063956.71687-1-pkshih@realtek.com
Originally, we keep RX standby timer to handle beamformee CSI, but this
spends power and causes system not entering power save mode. To improve
power consumption, release the timer if throughput becomes low.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230307141848.26403-1-pkshih@realtek.com
For different firmware type, it could use different IDMEM mode, so reset
it to default to avoid encountering error during we bisect firmware
version, like
rtw89_8852be 0000:03:00.0: Firmware version 0.29.26.0, cmd version 0, type 5
rtw89_8852be 0000:03:00.0: Firmware version 0.29.26.0, cmd version 0, type 3
rtw89_8852be 0000:03:00.0: fw security fail
rtw89_8852be 0000:03:00.0: download firmware fail
rtw89_8852be 0000:03:00.0: [ERR]fwdl 0x1E0 = 0x62
rtw89_8852be 0000:03:00.0: [ERR]fwdl 0x83F2 = 0x8
rtw89_8852be 0000:03:00.0: [ERR]fw PC = 0xb8931154
rtw89_8852be 0000:03:00.0: [ERR]fw PC = 0xb8931154
rtw89_8852be 0000:03:00.0: [ERR]fw PC = 0xb8931150
rtw89_8852be 0000:03:00.0: [ERR]fw PC = 0xb8931154
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230123065401.14174-5-pkshih@realtek.com
Some hardware modules don't have good RF characteristic as regular.
It could get ADC abnormal in low temperature, and it causes bad RX
performance and affects calibration result of DPK.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-3-pkshih@realtek.com
This change fixes the precision of CFO and TX EVM, and it could imporve
performance in some cases. Also, use the correctted definition for 8852A.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-2-pkshih@realtek.com
BSS color mapping register is different per IC, therefore, move this
register to chip_info and update the setting function. Without this patch,
wrong BSS color causes behavior abnormal, especially DL-OFDMA.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221214091803.41293-1-pkshih@realtek.com
RX DCK stands for RX DC calibration that affects CCA, so abnormal
calibration values resulted from calibration failure can cause TX get
stuck.
To solve this, redo calibration if result is bad (over thresholds). When
retry count is over, do recovery that sets high gain fields of RX DCK
results from low gain fields.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221209020940.9573-4-pkshih@realtek.com
Some DPK settings are wrong, and causes bad TX performance occasionally.
So, fix them by internal suggestions.
Fixes: da4cea16cb ("rtw89: 8852c: rfk: add DPK")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221209020940.9573-3-pkshih@realtek.com
If the interface is in AP/P2P GO mode, we adjust the TSF with random
offset to avoid TBTT of different vifs to overlap and collide.
For every new interface added, we adjust the value and resync for all
interfaces.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202061527.505668-2-pkshih@realtek.com
PoP stands for Packet on Packet that can improve performance in noisy
environment, but it could get RX stuck suddenly. In normal mode, firmware
can help to resolve the stuck, but firmware doesn't work in monitor mode.
Therefore, turn off PoP to avoid RX stuck.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221125072416.94752-4-pkshih@realtek.com
To detect TX or RX stuck, we implement SER (system error recovery) in
firmware to recover abnormal states of hardware, and report events to
driver. This kind of events could happen rarely per day.
SER might be true-positive or false-negative cases, and it could be failed
to recover true-positive case. We dump related registers to kernel message
at that moment and collect them from users, because they occur rarely,
randomly and hard to make sure we reproduce the same symptom. To address
problems accurately, add more registers by this patch.
It also might be false-positive cases that looks like TX or RX get stuck,
we need to dump registers from debugfs manually, so also add similar
things to debugfs as well.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221102014300.14091-3-pkshih@realtek.com
Dispatch is a component to decide packets forward to host, DMAC or
HAXIDMA. It contains CDT standing for CPU dispatcher, HDT standing
for host dispatcher, WDE standing for descriptor engine and PLE standing
for payload engine. STF is one kind of modes, it can be used if packet
send to hardware and doesn't need release report.
These debug port information can help to clarify the reason if
packets stuck in dispatch.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221102014300.14091-2-pkshih@realtek.com
WoWLAN is a feature which allows devices to be woken up from suspend
state through WLAN events.
When user enables WoWLAN feature and then let the device enter suspend
state, WoWLAN firmware will be loaded by the driver and periodically
monitors WiFi packets. Power consumption of WiFi chip will be reduced
in this state.
We now implement WoWLAN function in rtw8852ae and rtw8852ce chip.
Currently supported WLAN events include receiving magic packet,
rekey packet and deauth packet, and disconnecting from AP.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-7-pkshih@realtek.com
When entering WoWLAN mode, we need to drop all transmit packets,
including those in mac buffer, to avoid memory leakage, so implement
the drop_tx function.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-5-pkshih@realtek.com
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221014060237.29050-2-pkshih@realtek.com
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.
To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-6-pkshih@realtek.com
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-5-pkshih@realtek.com
DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output good quality signals.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-2-pkshih@realtek.com
To support variant models, such as 1x1 or 1T2R, we need this chip_ops to
change the path accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-8-pkshih@realtek.com
These chip_ops are used to assist BT coexistence module to control chip
specific operations, such as initial, pre-AGC, BT grant, set wifi priority
and tx power, RX gain, and get BT counter.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-6-pkshih@realtek.com
We need power on function to enable hardware circuits of MAC/BB/RF, and
then download firmware and load PHY parameters. After more settings, it
starts to work. When it enters idle, use power off function to have the
lowest power consumption.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-3-pkshih@realtek.com
set_channel is main function to configure channel and bandwidth for all
layers, namely MAC, BB and RF. Additionally, MAC layer enables CCK rate
checking to avoid wrong rate from driver. BB layer configures SCO
(Sample Clock Offset) for CCK, TX gain error/offset, and reset baseband
hardware circuit after all configurations done.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-7-pkshih@realtek.com
Before loading RF NCTL table, we need to configure IQK/DPK clock and reset
them, and then polling NCTL state ready. Since 8852BE needs additional
one setting, add it by this patch. Also, give them proper names.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-4-pkshih@realtek.com
8852CE is a combo chip, and WiFi driver controls pin MUX. To output BT
firmware log to specific hardware pin, set pin MUX to achieve.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220930134417.10282-1-pkshih@realtek.com
This chip_ops is to set TX power according to country, channel, rate and
so on. Since shared code is used to configure TX power, we only implement
specific part in this patch.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220928084336.34981-7-pkshih@realtek.com
Implement to power on/off BB and RF via MAC registers.
Add return type of chip_ops::disable_bb_rf, because it could fail to
disable. Also, correct naming of register 0x0200 used by the ops as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220927062611.30484-5-pkshih@realtek.com
NAV upper register is to limit the maximum NAV value to prevent
unexpected NAV, but the old setting is too small to reflect NAV from
AP transmiting big MPDU at once.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220916033811.13862-3-pkshih@realtek.com
8852C needs this to change CMAC dma to full mode to keep receiving
packets after RX full event being resolved.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220916033811.13862-2-pkshih@realtek.com
To reduce register IO, combine set_gnt_wl/set_gnt_bt to set the same
register one time. Because RTL8852C use different register to control
antenna path, so make correction of path control related debug logs.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220913092546.43722-8-pkshih@realtek.com
