Since chips could use different version of BA CAM H2C command, add a
chip_ops to abstract the operation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091134.67007-4-pkshih@realtek.com
In concurrent mode, when STA interface is scanning, it causes
AP interface TX beacon on wrong channel. We modified it to scan
with the operating channel when one of the interfaces is already
connected. Additionally, STA interface need to stop scan when AP
interface is starting to avoid TX beacon on wrong channel. Finally,
AP interface need to stop TX beacon when STA interface is scanning
and switching to non-OP channel,This prevent other device to get
beacons on wrong channel.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231129070046.18443-5-pkshih@realtek.com
We add a scanning check to avoid entering IPS after ROC (remain on
channel) during scanning. Additionally, When P2P scanning, the flow is
`1. p2p_listen step` and `2. configure filter` and `3. p2p_scan starts`
in wpas, but in kernel, cfg80211 uses another workqueue to notify driver
the filter change, so sometimes we see (1 > 3 > 2), that will cause Rx
filter related to scan to be cleared. Therefore, we add a scanning check
when configure filter to avoid scan results to be filtered. Finally, we
cancel the ROC delayed workqueue before entering ROC to avoid entering
twice, which might cause leaving ROC too early.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231129070046.18443-4-pkshih@realtek.com
In MCC STA+GO mode, we calculate NoA information and fill it into the
beacon of P2P GO. Since NoA uses only 32 bits to describe time things,
we need to deal with renewal when TSF[63:32] is carried. We trigger FW
to notify that. Then, we can update NoA information for new time period
once we get notification from FW.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-9-pkshih@realtek.com
MCC fills duration limit of a role according to NoA description.
If P2P PS changes during MCC, we don't process P2P PS via normal
flow. Instead, we re-fill duration limit of the role for new NoA
description, and then we do MCC update.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230908031145.20931-7-pkshih@realtek.com
rx_filter is used to decide which kind of packets are received to driver,
or just dropped by MAC layer to reduce bus traffic.
The bit definitions of old and new chips are the sames, but only address
is changed, so define a field to generalize usage.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-5-pkshih@realtek.com
There are two copies of MAC hardware called band0 and band1. Basically,
the only difference between them is base address, so we can share functions
with a 'band' (or 'mac_idx') argument.
The offset of base address of WiFi 6 and 7 are 0x2000 and 0x4000
respectively, so add band1_offset field to new introduced struct
mac_gen_def to possibly reuse functions.
Using below spatch script to convert callers:
@@
expression reg, band;
@@
- rtw89_mac_reg_by_idx(reg, band)
+ rtw89_mac_reg_by_idx(rtwdev, reg, band)
@@
expression reg, port, band;
@@
- rtw89_mac_reg_by_port(reg, port, band)
+ rtw89_mac_reg_by_port(rtwdev, reg, port, band)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-2-pkshih@realtek.com
We prepare to deal with multiple channels via new entity modes.
* MCC_PREPARE: Transitional mode before MCC
* MCC: Multi-Channel Concurrent mode
And, enum of sub-entity is extended for second channel context.
We add the entry flow of multi-channel handling and the core stuffs
for extended index of sub-entity. And, we now deal with the filling
of entity channels' info in entity recalc where we know the number
of active chanctx. However, the other detail coding of MCC start/stop
will be implemented in the following.
Besides, chanctx listener struct is pre-added in chip info. Each
component can add callback type in chanctx listener and configure
its callback function to react according to chanctx states. We know
at least RFK (RF calibration) and BTC (BT coexistence) will require
such callbacks.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-7-pkshih@realtek.com
We adjust these processes which can work accodrding to vif but call
rtw89_chan_get() with static RTW89_SUB_ENTITY_0. After multi-channel
support, chanctx of vif won't always be on RTW89_SUB_ENTITY_0. So,
we make them call rtw89_chan_get() with rtwvif->sub_entity_idx.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230816082133.57474-5-pkshih@realtek.com
Configure the corresponding power type for 6 GHz regulatory if we can
determine one single target. Otherwise, we use the default one.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230602150556.36777-5-pkshih@realtek.com
There are a number of upcoming things in both the stack and
drivers that would otherwise conflict, so merge wireless to
wireless-next to be able to avoid those conflicts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This driver relies on IEEE80211_CONF_PS of hw->conf.flags to turn off PS or
turn on dynamic PS controlled by driver and firmware. Though this would be
incorrect, it did work before because the flag is always recalculated until
the commit 28977e790b ("wifi: mac80211: skip powersave recalc if driver SUPPORTS_DYNAMIC_PS")
is introduced by kernel 5.20 to skip to recalculate IEEE80211_CONF_PS
of hw->conf.flags if driver sets SUPPORTS_DYNAMIC_PS.
Correct this by doing recalculation while BSS_CHANGED_PS is changed and
interface is added or removed. For now, it is allowed to enter PS only if
single one station vif is working, and it could possible to have PS per
vif after firmware can support it. Without this fix, driver doesn't
enter PS anymore that causes higher power consumption.
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Cc: stable@vger.kernel.org # 6.1+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527082939.11206-3-pkshih@realtek.com
TX antenna diversity is a mechanism to select a proper antenna from two
antenna for single one hardware PHY chip. It chooses antenna with better
EVM or RSSI, and use GPIO to control SPDT to switch selected antenna.
RFE type from efuse is used to define if a module can support TX antenna
diversity when (type % 3) is 2.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418012820.5139-3-pkshih@realtek.com
Since we can get the current channel definition each interface maps to,
remove store_op function that is no longer required to make things simple.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415034900.15679-3-pkshih@realtek.com
Mac80211 core may ask driver to change to idle mode during HW scan,
then H2C command for HW scan will send failed since chip is in idle
mode. Therefore, We check the SCANNING flag before entering IPS to
prevent this behavior.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415034900.15679-2-pkshih@realtek.com
Add support of remain on channel ops. Since channel context is
required to enable multi-channel concurrent(MCC) and the current
ROC in mac80211 don't support more than 1 channel context, add this
to let P2P and other protocols relying on this work as expected.
The off-channel duration and cancel timing is purely controlled by
upper layers.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-4-pkshih@realtek.com
Adding this supports beacon filter and connection quality monitor.
To make host CPU wake up less, let firmware perform signal
monitoring and beacon processing, then notify driver upon signal
changes or beacon loss.
This feature needs firmware 0.27.56 or newer to support it.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-2-pkshih@realtek.com
The newer chips use the newer firmware branches, e.g. v027, v029.
And, those firmware branches are supposed to support packet drop
when they are just branched out.
The initial firmware branch used by each chip is as below.
* 8852A: v009
* 8852C: v027
* 8852B: v027
So, only 8852A may use firmware which doesn't support packet drop at
runtime. To save trivial positive listing in firmware feature table,
we change to reverse judgment.
Besides, rtw89_mac_ptk_drop_by_band_and_wait() missed to check firmware
feature before calling rtw89_fw_h2c_pkt_drop(). We also fix it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230220070202.29868-7-pkshih@realtek.com
For upcoming firmware, driver needs to do packet offload to firmware to
ensure LPS protocol work properly, so we update current connection and
disconnect flow to maintain packet offload flow, and integrate with
current WoWLAN flow which also needs packet offload.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230123065401.14174-3-pkshih@realtek.com
Remove according vifs from list if we couldn't set this interface up.
Otherwise the rtwvif_list could contain unreferenced objects.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202061527.505668-4-pkshih@realtek.com
Disable hardware beacon related functions when ap stops. So hardware won't
transmit beacons while interface is already removed.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202061527.505668-3-pkshih@realtek.com
First, introduce struct rtw89_sub_entity for chanctx related stuffs.
Second, add enum rtw89_sub_entity_idx to rtw89_vif for vif operation
to access its/right chanctx stuffs after future multi-channel support.
Besides, RTW89_SUB_ENTITY_0 is the default chanctx entry throughout
driver, i.e. it's used for things which may not have a target chanctx
yet. So, we need to ensure that RTW89_SUB_ENTITY_0 is always working.
If there is at least one alive chanctx, then one of them must take
RTW89_SUB_ENTITY_0. If no alive chanctx, RTW89_SUB_ENTITY_0 will be
filled by rtw89_config_default_chandef().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221129083130.45708-7-pkshih@realtek.com
During doing change_interface(), hardware is power-off, so some components
are inaccessible and return error. This causes things unexpected, and we
don't have a warning message for that. So, ignore some IO operations in
this situation, and add a warning message to indicate something wrong.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117085235.53777-1-pkshih@realtek.com
WoWLAN is a feature which allows devices to be woken up from suspend
state through WLAN events.
When user enables WoWLAN feature and then let the device enter suspend
state, WoWLAN firmware will be loaded by the driver and periodically
monitors WiFi packets. Power consumption of WiFi chip will be reduced
in this state.
We now implement WoWLAN function in rtw8852ae and rtw8852ce chip.
Currently supported WLAN events include receiving magic packet,
rekey packet and deauth packet, and disconnecting from AP.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-7-pkshih@realtek.com
Align with the spec of 802.11ax, follow the conditions for not responding
with an HE TB PPDU. When there are OBSS that cannot interpret 26-tone RU
transmissions, we should disable such transmissions.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922012719.15037-1-pkshih@realtek.com
Support P2P client to process Notice of Absence (NoA) mechanism when it
connects with P2P GO applying an NoA schedule. We define some action
types including init, update, remove and terminate in h2c function to
enable/disable NoA schedule.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-6-pkshih@realtek.com
Check IEEE80211_TX_CTL_NO_CCK_RATE flag to avoid sending frames with
CCK rates in 2GHz band.
In TX flow, add IEEE80211_TX_CTL_NO_CCK_RATE flag to check and get its
lowest rate without CCK rates if the TX type is mgmt frames or data frames.
Besides, the decision of phy rate and retry rate in P2P mode are also
be handled.
In P2P GO mode, it should send beacon of no CCK rates in its frame rate.
Therefore, We add a condition to decide which rate is added to beacon
content.
Moreover, we avoid setting a mask of rates to be used for rate control
selection before and after connection in P2P mode.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-3-pkshih@realtek.com
To support P2P in driver, we set P2P interface mode to the wiphy
allocated for 802.11 PHY and add a change interface function to
switch the interface type to P2P.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-2-pkshih@realtek.com
Introudce a H2C feature to drop packets according to given parameters.
And, we implement instances to drop packets from BE, BK, VI, VO queues
by vif or sta. Then, we refine our callback of ieee80211_ops::flush to
deal with the case of drop=true via this feature.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220914035034.14521-3-pkshih@realtek.com
Add ops set_tid_config to support TID specific configuration.
We currently only support ampdu setting.
The command example is:
iw wlan0 set tidconf tids 0x3 ampdu off
iw wlan0 set tidconf peer xx:xx:xx:xx:xx:xx tids 0x2 ampdu on
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220912070014.10018-3-pkshih@realtek.com
Two fields, TX/RX ANT NUM, are introduced to address variant TX/RX antenna
number of hardware. For example, a 1x1 chip with TX diversity, TX NSS = 1
and TX/RX ANT NUM = 2.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220908074140.39776-3-pkshih@realtek.com
Support mac80211 chanctx series ops. Still, currently support
single channel. Based on this premise, things should be similar
to before. So, we haven't dealt with relationship between vif
and chanctx in depth. Instead, we leave both ::assign_vif()
and ::unassign_vif() as noops for now.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-12-pkshih@realtek.com
Originally, we didn't support mac80211 chanctx, so it's expected that
ieee80211_hw::conf::chandef would be filled by mac80211. And then, we
could just query it whenever we need the current chandef.
However, we are planing to support mac80211 chanctx. After that, the
above assumption would be broken. So, we adjust a bit ahead to reduce
future works about mac80211 chanctx.
After this, we don't query ieee80211_hw::conf::chandef directly, and
we add a map, entity_map, to HAL to indicate which chandef came from
stack. And it will later be used to recalcate entity mode.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-9-pkshih@realtek.com
We are planning to support mac80211 chanctx. To reduce future works,
the driver architecture is adjusted first to isolate related things.
According to chip, our HW may have multiple sub-entities to support
multiple mac80211 chanctx. Struct rtw89_chan has been introduced for
things about channel/band/subband/... Now introduce struct rtw89_chan_rcd
to record difference after assigning new one of struct rtw89_chan.
We will implement and support chanctx with single channel first, i.e.
only use entry in RTW89_SUB_ENTITY_0, before handling dual channels.
Our hierarchy in planning will become as the following.
DEV
-> HAL
---> entity (manage status across sub-entities)
-----> sub-entity[*] (support mac80211 chanctx)
where each sub-entity contains one struct rtw89_chan.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-4-pkshih@realtek.com
When calling start/stop_ap(), mac80211 already has a protected
link_conf pointer. Pass it to the driver, so it shouldn't
handle RCU protection.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Normally, we only allocate an address CAM and single one MAC ID to AP in
STA mode. To support TDLS, we handle TDLS peers like AP handles stations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-2-pkshih@realtek.com
In start_ap and stop_ap mac80211 callbacks pass the link_id
to the drivers.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously channel maintained by driver could be different from the
ones hardware actually is. Restore these variables back to prevent
unexpected behavior.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220520071731.38563-2-pkshih@realtek.com
When peer's NSS, rate or bandwidth is changed, we update RA(rate adaptive)
mask to ensure transmitting packets properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-2-pkshih@realtek.com
As the fw features gradually increase, it would be better that
we have a set of methods to maintain fw features instead of using
scattered bool variables.
We reconstruct the way fw recognize features, and introduce
RTW89_CHK_FW_FEATURE() / RTW89_SET_FW_FEATURE() to check / set
fw features for uses.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-8-pkshih@realtek.com
Declare this function allows us to use customized scanning policy, so
each scan takes less time. This is a similar implementation to hw_scan
in rtw88, except that we offload more items to firmware and extend the
maximum IE length. For backward compatibility, we fallback to sw_scan
when firmware does not support this feature.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220225030851.13327-2-pkshih@realtek.com
Configure firmware and hardware to run AP mode. The start_ap() setup
bssid, mac port, mac_id entry, and does RFK. The stop_ap() reset the
state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-6-pkshih@realtek.com
vif_type mapping indicates hardware operating mode corresponding to vif
type. In STA mode, hardware mode should be INFRA or NO_LINK mode
dynamically according to association status. Since AP mode don't need to
change this by association status intuitively, just do the mapping in
STA mode.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-4-pkshih@realtek.com
Update beacon content if TIM bitmap maintained by mac80211 is changed.
Since .set_tim must be atomic but driver uses mutex lock, we add a work.
Otherwise, kernel says "sched: RT throttling activated" and lock down.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-6-pkshih@realtek.com
Firmware sends out beacon content generated by mac80211, and then stations
can receive beacon and work with this AP properly. Also, we download
beacon content again if TIM is changed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-4-pkshih@realtek.com
BA CAM is used to ACK peer's packets, so it must be established when
IEEE80211_AMPDU_RX_START, and free it by IEEE80211_AMPDU_RX_STOP.
The hardware can support two static BA CAM entries, so I implement a bitmap
and a struct to record which entry is used and its corresponding tid. Also,
the hardware can learn and create dynamic BA CAM entries automatically if
received packets don't match static BA CAM. That means it can still work if
we don't use H2C to set static BA CAM. An exception is tid=0 should be
always allocated in static BA CAM, so an existing static BA CAM will be
replaced if it is full and peer is going to establish a BA with tid=0.
The new firmware use new format of this H2C, so I upgrade it as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220104012052.6911-1-pkshih@realtek.com
This is found by Smatch static checker warning:
drivers/net/wireless/realtek/rtw89/mac80211.c:31 rtw89_ops_tx()
error: uninitialized symbol 'qsel'.
The warning is because 'qsel' isn't filled by rtw89_core_tx_write() due to
failed to write. The way to fix it is to avoid kicking off TX DMA, so add
'return' to the failure case.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211201093816.13806-1-pkshih@realtek.com
With wrong rtwsta->mac_id, it can't send out ack properly when we receive
assoc response occasionally. Then, it failed to connect an AP.
The cause is that we store 'sta' and use it somewhere. To correct this,
remove the variable and use mac_id in drv_priv of 'sta' or 'vif' passed
by mac80211.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211201080607.11211-1-pkshih@realtek.com
This driver named rtw89, which is the next generation of rtw88, supports
Realtek 8852AE 802.11ax 2x2 chip whose new features are OFDMA, DBCC,
Spatial reuse, TWT and BSS coloring; now some of them aren't implemented
though.
The chip architecture is entirely different from the chips supported by
rtw88 like RTL8822CE 802.11ac chip. First of all, register address ranges
are totally redefined, so it's impossible to reuse register definition. To
communicate with firmware, new H2C/C2H format is proposed. In order to have
better utilization, TX DMA flow is changed to two stages DMA. To provide
rich RX status information, additional RX PPDU packets are added.
Since there are so many differences mentioned above, we decide to propose
a new driver. It has many authors, they are listed in alphabetic order:
Chin-Yen Lee <timlee@realtek.com>
Ping-Ke Shih <pkshih@realtek.com>
Po Hao Huang <phhuang@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Vincent Fann <vincent_fann@realtek.com>
Yan-Hsuan Chuang <tony0620emma@gmail.com>
Zong-Zhe Yang <kevin_yang@realtek.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211008035627.19463-1-pkshih@realtek.com
