This function, currently called by WoWLAN flow, polls until specific HW
queues are empty. The polling bit definitions are not totally the same
between WiFi 6 and 7 chips. In addition, the check conditions are also
a little different. So, we differentiate the implementations according to
chip gen.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124071703.132549-6-pkshih@realtek.com
The reserved quota of DLE (data link engine) is used for processing next
packet. Add this to get quota number, and then WiFi 7 chips can use them.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124071703.132549-3-pkshih@realtek.com
Define 8922A buffer quota that are used by HCI control flow, payload
engine, descriptor engine and etc for operation modes, such as SCC (single
channel concurrence) and download firmware. Since WiFi 7 chips has more
buffer classifications, add fields and struct according to design.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124071703.132549-2-pkshih@realtek.com
Use function pointers to abstract efuse access, and introduce an new
function to convert efuse power state that is needed by WiFi 7 chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231117024029.113845-3-pkshih@realtek.com
The new chips change hardware design to shrink entry size of address
CAM from 0x40 to 0x20, so make this change accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231027015059.10032-2-pkshih@realtek.com
Beamforming monitor is used to adjust registers to fine tune performance
and power save, and currently only existing WiFi 6 chips need it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-7-pkshih@realtek.com
When associated peer has beamformer capability, we should enable
beamformee, set CSI parameter, and configure rate to send CSI packets.
Since registers of WiFi 7 chips are very different from existing chips,
separate configuration functions.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-6-pkshih@realtek.com
When associated peer has beamformer capability, enable hardware beamformee
function, and then hardware can run sounding protocol itself. Oppositely,
disable this function when disassociated. Define different registers for
WiFi 6 and 7 generations respectively.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-5-pkshih@realtek.com
When connected with 802.11ax AP, MU-EDCA parameters are given, so enable
this hardware function by registers according to chip generation.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-3-pkshih@realtek.com
When TX size or time of packet over RTS threshold set by this register,
hardware will use RTS protection automatically. Since WiFi 6 and 7 chips
have different register address for this, separate the address according
to chip gen.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231012021455.19816-2-pkshih@realtek.com
There are two difference between Wi-Fi 6 and Wi-Fi 7 chips.
1. Address range of TX power control register
2. Checking code to get a TX power control register
So, separate the implementation of them, access according to
chip generation, and rename original things with a suffix `_ax`.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231003015446.14658-2-pkshih@realtek.com
Using mac_gen pointer to reuse the code with WiFi 7 chips, and define
MAC ports registers for WiFi 7 chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230911082049.33541-7-pkshih@realtek.com
Though WiFi 7 chips need BB MCU firmware, we don't download it in probe
stage. Instead, only bring interface up under normal operation or WoWLAN
mode. So, add an argument to assist download flow to setup download
settings properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-6-pkshih@realtek.com
For WiFi 6 chips, there is only single one firmware i.e. WiFi CPU firmware,
so no need an argument to discriminate them. For WiFi 7 chips, BB MCU
firmware is introduced, and we need to check it ready after downloading.
For each type of firmware, we need to check corresponding hardware ready
bit. After downloading all firmware, check status code to determine if
all things are ready.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-5-pkshih@realtek.com
In order to reuse the flow to download firmware, define some mac_gen::ops
to implement them for WiFi 6 and 7 chips individually. This doesn't change
logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-3-pkshih@realtek.com
To download firmware, we need to check path is ready. There are two kinds
of path -- one is to download firmware header, and the other is to download
firmware body.
Since the polling method is different from WiFi 7 chips, make it to be
an individual function, and then we can reuse the download flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-2-pkshih@realtek.com
rx_filter is used to decide which kind of packets are received to driver,
or just dropped by MAC layer to reduce bus traffic.
The bit definitions of old and new chips are the sames, but only address
is changed, so define a field to generalize usage.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-5-pkshih@realtek.com
Define base address of WiFi 7 internal memory according to design to
provide the same functions as existing WiFi 6 chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-4-pkshih@realtek.com
To diagnose abnormal behavior, we need to dump certain internal memory.
For example, dump security CAM when debugging encryption/decryption
problems, or dump BA CAM when debugging abnormal BlockAck.
Since the indirect address and internal memory base address are different
between WiFi 6 and 7 chips, add fields to reuse codes.
Also, only WiFi 6 chips initialize DMAC and CMAC tables via this indirect
interface, so no need to change the constant register address, and
new firmware will help to initialize these tables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-3-pkshih@realtek.com
There are two copies of MAC hardware called band0 and band1. Basically,
the only difference between them is base address, so we can share functions
with a 'band' (or 'mac_idx') argument.
The offset of base address of WiFi 6 and 7 are 0x2000 and 0x4000
respectively, so add band1_offset field to new introduced struct
mac_gen_def to possibly reuse functions.
Using below spatch script to convert callers:
@@
expression reg, band;
@@
- rtw89_mac_reg_by_idx(reg, band)
+ rtw89_mac_reg_by_idx(rtwdev, reg, band)
@@
expression reg, port, band;
@@
- rtw89_mac_reg_by_port(reg, port, band)
+ rtw89_mac_reg_by_port(rtwdev, reg, port, band)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-2-pkshih@realtek.com
There are a number of upcoming things in both the stack and
drivers that would otherwise conflict, so merge wireless to
wireless-next to be able to avoid those conflicts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add basic functions to power on chip and enable and access BB/RF, as
well as reset and hardware settings of BB.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-5-pkshih@realtek.com
Newer FW re-design SER (syetem error recovery) L1 (level 1) flow.
New L1 flow will expect two extra states before original L1 flow.
* Before:
fw --- M1 --> driver
fw <-- M2 --- driver
fw --- M3 --> driver
fw <-- M4 --- driver
fw --- M5 --> driver
* After:
fw --- pre-M0 --> driver
fw <-- post-M0 --- driver
fw --- M1 --> driver
fw <-- M2 --- driver
fw --- M3 --> driver
fw <-- M4 --- driver
fw --- M5 --> driver
Then before M1, FW gets one more interval to deal with things that FW
should have handled well. To consider backward/forward compatibility,
FW and driver won't change flow from M1 to M5. (only except that halt
trigger control will change a little bit.) So, there will be two differnt
starting points of SER L1.
* old FW: SER L1 starts from M1
* new FW: SER L1 starts from pre-M0
Then, driver adds the new SER L1 entry and also keep the original one
instead of changing it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508084335.42953-3-pkshih@realtek.com
Configure DLE (data link engine) memory size for operating modes.
Similarly, HFC standing for HCI flow control is used to set quota
according to operating modes, which are SCC or download firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421024551.29994-9-pkshih@realtek.com
The function to request DLE (data link engine) buffer uses 'u16' as return
value that mixes error code, so change it to 'int' as regular error code.
Also, treat invalid register value (0xfff) as an error.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414082228.30766-1-pkshih@realtek.com
To support WoWLAN mode for 8852be, we add one PLE quota setting and
WoWLAN stub, which shows that supported WLAN events include receiving
magic packet, rekey packet and deauth packet, and disconnecting from AP.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230410053438.10682-1-pkshih@realtek.com
The chip contains digital and analog parts, and each of them has its own
version number. This is used by BT coexistence mechanism to make strategy
decision for different analog version.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330133324.19538-2-pkshih@realtek.com
Adding this supports beacon filter and connection quality monitor.
To make host CPU wake up less, let firmware perform signal
monitoring and beacon processing, then notify driver upon signal
changes or beacon loss.
This feature needs firmware 0.27.56 or newer to support it.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-2-pkshih@realtek.com
RXI300 is a HW design to maintain stuffs across BUS, e.g. AXI, AHB, APB.
It will feedback an error when host does an invalid BUS operation.
For example,
* BUS master request without power/clock on.
* host reads/writes/accesses an invalid address.
They might lead to problems such as BUS timeout, platform hang, etc. So,
once if RXI300 feedback an error, it notifies that driver need a L2 SER
(system error recovery) to reset things.
Previously, driver did not parse the error scenario for RXI300. We add
it and assign a corresponding error code which will make SER flow do L2
reset.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230119063529.61563-3-pkshih@realtek.com
Add mac function rtw89_mac_port_get_tsf() to get TSF by port.
It will be used when MCC (multi-channel concurrency) calculates
timing things.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230119062453.58341-4-pkshih@realtek.com
Originally, rtw89_mac_port_tsf_sync() contains randomization logic
internally. However, not all situation, we need the randomization.
So, split out the generic part from it. And, make the full logic of
original one contained in rtw89_mac_port_tsf_sync_rand(). It will
still be used by its original caller as before. Then, the generic
one will be used in MCC (multi-channel concurrency) management flow.
MCC will implement its logic to decide the offset for TSF sync.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230119062453.58341-3-pkshih@realtek.com
Strictly speaking, the unit of the offset should be TU instead of ms.
So, correct it and the macro for calculation. Then, to make the macro
generic, the factor n is moved outside.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230119062453.58341-2-pkshih@realtek.com
Disable hardware beacon related functions when ap stops. So hardware won't
transmit beacons while interface is already removed.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202061527.505668-3-pkshih@realtek.com
If the interface is in AP/P2P GO mode, we adjust the TSF with random
offset to avoid TBTT of different vifs to overlap and collide.
For every new interface added, we adjust the value and resync for all
interfaces.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202061527.505668-2-pkshih@realtek.com
Process C2H(s) related to MCC (multi-channel concurrency). These handling,
which either call rtw89_complete_cond() or show message in debug mode, can
be considered atomic/lock-free. So, they should be safe to be processed
directly after C2H pre-check in previous patch.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221129083130.45708-5-pkshih@realtek.com
Before queuing C2H work, we check atomicity of the C2H's handler first now.
If atomic or lock-free, handle it directly; otherwise, handle it with mutex
in work as previous. This prepares for MAC MCC C2Hs which require to be
processed directly. And, their handlers will be functions which can be
considered atomic.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221129083130.45708-3-pkshih@realtek.com
To detect TX or RX stuck, we implement SER (system error recovery) in
firmware to recover abnormal states of hardware, and report events to
driver. This kind of events could happen rarely per day.
SER might be true-positive or false-negative cases, and it could be failed
to recover true-positive case. We dump related registers to kernel message
at that moment and collect them from users, because they occur rarely,
randomly and hard to make sure we reproduce the same symptom. To address
problems accurately, add more registers by this patch.
It also might be false-positive cases that looks like TX or RX get stuck,
we need to dump registers from debugfs manually, so also add similar
things to debugfs as well.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221102014300.14091-3-pkshih@realtek.com
Dispatch is a component to decide packets forward to host, DMAC or
HAXIDMA. It contains CDT standing for CPU dispatcher, HDT standing
for host dispatcher, WDE standing for descriptor engine and PLE standing
for payload engine. STF is one kind of modes, it can be used if packet
send to hardware and doesn't need release report.
These debug port information can help to clarify the reason if
packets stuck in dispatch.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221102014300.14091-2-pkshih@realtek.com
WoWLAN is a feature which allows devices to be woken up from suspend
state through WLAN events.
When user enables WoWLAN feature and then let the device enter suspend
state, WoWLAN firmware will be loaded by the driver and periodically
monitors WiFi packets. Power consumption of WiFi chip will be reduced
in this state.
We now implement WoWLAN function in rtw8852ae and rtw8852ce chip.
Currently supported WLAN events include receiving magic packet,
rekey packet and deauth packet, and disconnecting from AP.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-7-pkshih@realtek.com
When entering WoWLAN mode, we need to drop all transmit packets,
including those in mac buffer, to avoid memory leakage, so implement
the drop_tx function.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-5-pkshih@realtek.com
PLE RX quota, which is the setting of RX buffer, is needed to be adjusted
dynamically for WoWLAN mode, and restored when back to normal mode.
The action is not needed for rtw8852c chip.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-4-pkshih@realtek.com
For WoWLAN mode, we need to download WoWLAN firmware by calling
fw_download(). Another, to disable/enable WiFi CPU is needed before
calling fw_download. Since Firmware runs on WiFi CPU, it is intuitive
to combine enable_cpu/disable_cpu functions into fw_download.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-3-pkshih@realtek.com
We need power on function to enable hardware circuits of MAC/BB/RF, and
then download firmware and load PHY parameters. After more settings, it
starts to work. When it enters idle, use power off function to have the
lowest power consumption.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-3-pkshih@realtek.com
MAC maintains TX FIFO to transmit packets with meta data to BB layer. To
debug abnormal transmission, we need to dump the content to dig problem.
Since FIFO of 8852C locates on different address with different size and
need additional switch to enable read operation, this patch adds the
changes accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220930134417.10282-2-pkshih@realtek.com
Implement to power on/off BB and RF via MAC registers.
Add return type of chip_ops::disable_bb_rf, because it could fail to
disable. Also, correct naming of register 0x0200 used by the ops as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220927062611.30484-5-pkshih@realtek.com
Align with the spec of 802.11ax, follow the conditions for not responding
with an HE TB PPDU. When there are OBSS that cannot interpret 26-tone RU
transmissions, we should disable such transmissions.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922012719.15037-1-pkshih@realtek.com
Support P2P client to process Notice of Absence (NoA) mechanism when it
connects with P2P GO applying an NoA schedule. We define some action
types including init, update, remove and terminate in h2c function to
enable/disable NoA schedule.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220922010435.12167-6-pkshih@realtek.com
SER (system error recovery) can deal with different crash types by
different levels of processes. Previous FW crash simulation triggers
a CPU exception which is one kind of SER L2 type. It can verify SER L2
flow which includes HW/FW restart.
Now, we want to increase crash simulation types. A debug function is added
to trigger control error in purpose for SER L1 simulation/verification.
And, debugfs fw_crash is extended to accept different parameters.
echo 1 > fw_crash:
simulate CPU exception as before
(keep 1 for compatibility with previous)
It will be catched and handled by SER L2.
(this requires HW/FW restart)
echo 2 > fw_crash:
simulate control error
It will be catched and handled by SER L1.
(driver and FW cooperate to recover this)
Besides, in order to apply to the above two cases,
rename RTW89_FLAG_RESTART_TRIGGER to RTW89_FLAG_CRASH_SIMULATING
and adjust where SER flow clears this bit for both L1 and L2.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220914035034.14521-5-pkshih@realtek.com
Introudce a H2C feature to drop packets according to given parameters.
And, we implement instances to drop packets from BE, BK, VI, VO queues
by vif or sta. Then, we refine our callback of ieee80211_ops::flush to
deal with the case of drop=true via this feature.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220914035034.14521-3-pkshih@realtek.com
Some PCI and MAC registers are changed for different
chips and correct them accordingly. And HCI MAD functions
belongs to MAC core, so move it to mac.h/.c.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220912071706.13619-3-pkshih@realtek.com
When starting to send heavy traffic in low power mode,
driver will call multiple tx wake notify to wake firmware
within a short time. In this situation, firmware may miss
power mode change request from driver and leads to status
error. So we change driver to call power_mode_change at most
three times to make sure firmware could get the request.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220819064811.37700-2-pkshih@realtek.com
This watchdog timeout status bit indicates hardware gets wrong, so run SER
L2 flow that calls mac80211 to restart hardware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220520071731.38563-4-pkshih@realtek.com
BSSID CAM is a kind of CAM that is used to determine if we receive a packet
or not. Add an entry to assist in debugging.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-6-pkshih@realtek.com
Initialize registers to default values, such as PTA and GNT pin, and set
pin MUX according to number of antenna on hardware module.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-10-pkshih@realtek.com
Disable watchdog timer to prevent it timeout suddenly.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-8-pkshih@realtek.com
An export symbol costs about 40 bytes (in x86 with gcc), so use a structure
containing these small arrays to reduce code size.
text data bss dec hex filename
34932 1410 0 36342 8df6 mac.o (before)
34276 1258 0 35534 8ace mac.o (after)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220315015522.11366-1-pkshih@realtek.com
The raw error code might combine error scenario and error status.
But, the error scenario isn't parsed previously. It makes us mishandle
cpu exception and assertion. Now, we correct the error status for them.
Besides, a few uses of error status are refined.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-4-pkshih@realtek.com
Previously, mac_mem_base_addr_table was declared in debug.c locally
because it's only used via debugfs to dump mac memory. Now, we plan to
refine SER (system error recover) flow which will also need to dump mac
memory to somewhere as information for error which is catched. So, we
move mac_mem_base_addr_table to mac.c rtw89_mac_mem_base_addrs earlier
as common code.
(no logic is changed)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-3-pkshih@realtek.com
These function is used to stop transmitting when we are going to switch
channels or do some RF calibration. Before these operations, we need to
stop channel transmission and backup setting into parameter tx_en. After
operations are done, resume transmitting by backup parameter tx_en.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-13-pkshih@realtek.com
In order to support 8852C that uses 32 bits to control TX types.
This patch doesn't really use 32 bits tx_en yet, but next patch will
use it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-12-pkshih@realtek.com
The BT-coexistence uses these function to control antenna and TDMA, so
implement the variant type to support all chips.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-10-pkshih@realtek.com
The CFO tracking algorithm is the same, but control methods are different.
Set parameters via xtal serial interfaces (SI).
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-3-pkshih@realtek.com
DAV is an another efuse region that new chip, like 8852C, has this region.
Extend the code to read it, and convert the physical map to logical map
followed by original logical map.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-12-pkshih@realtek.com
New chipset uses individual power_{on/off} functions to replace old power
sequences, because it is hard to represent new complicated flow in a
sequence table.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-7-pkshih@realtek.com
We found management frames get stuck when wifi chip
enters low ps mode. So we add one notify wake function
to trigger wifi chip into normal mode before forwarding
management frames.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220225030851.13327-3-pkshih@realtek.com
Declare this function allows us to use customized scanning policy, so
each scan takes less time. This is a similar implementation to hw_scan
in rtw88, except that we offload more items to firmware and extend the
maximum IE length. For backward compatibility, we fallback to sw_scan
when firmware does not support this feature.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220225030851.13327-2-pkshih@realtek.com
In AP mode, when a STA associate to us, we need to create an entry in
firmware and hardware, and then they can transmit data properly.
The entry index called mac_id which is assigned when sta_add, and we ask
firmware to create an entry for an associated station. Also, the address
CAM should be filled so hardware can know which packet is ours, and lookup
the mac_id for further use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-5-pkshih@realtek.com
This C2H notify driver the beacon count we send out. We don't handle the
content for now, so add a dummy handler to avoid messages, like
rtw89_pci 0000:03:00.0: c2h class 0 func 3 not support
C2H: 00000000: 01 03 01 3f 0f 00 00 00 80 0a 00 00 00 00 a0
rtw89_pci 0000:03:00.0: c2h class 0 func 3 not support
C2H: 00000000: 01 03 01 40 0f 00 00 00 00 03 20 00 00 00 a5
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220107034239.22002-5-pkshih@realtek.com
We are planning to support more chipsets, e.g. 8852C. Before that, we
consider architecutre to handle multiple kinds of chipsets. Obviosuly,
based on original design, rtw89_core module will have large size even
if there is only one chipset under running. It is because all chipset
related things are put in rtw89_core now. To reduce such overhead, we
extract modules of rtw89 and adjust dependencies between modules.
The following assumes that 8852AE, 8852AU, and 8852CE are all supported,
we describe the difference before and after extraction.
[Before extraction]
-------------
|------------------------------------ | rtw89_usb |
V -------------
--------------------------------------- -------------
| rtw89_core (including 8852A, 8852C) | <--- | rtw89_pci |
--------------------------------------- -------------
The data of 8852A and 8852C are built in rtw89_core.
And rtw89_pci is the entry of 8852AE and 8852CE.
And rtw89_usb is the entry of 8852AU.
[After extraction]
------------- ----------------
|----------- | rtw89_usb | <-------- | rtw89_8852au |
| ------------- ----------------
V --------------- |
-------------- | | <---------------
| rtw89_core | <--- | rtw89_8852a |
-------------- | | <---------------
^ ^ --------------- |
| | ------------- ----------------
| | | | <-------- | rtw89_8852ae |
| |----------- | rtw89_pci | ----------------
| | | <-----------------
| ------------- |
| --------------- ----------------
|--------------- | rtw89_8852c | <------ | rtw89_8852ce |
--------------- ----------------
The data of 8852A/8852C is extracted to rtw89_8852a/rtw89_8852c.
And rtw89_pci/rtw89_usb handles only common flow of pci/usb bus.
Finally, 8852AE, 8852AU, and 8852CE have individual entry modules,
i.e. rtw89_8852ae, rtw89_8852au, and rtw89_8852ce correspondingly.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221025828.25092-1-pkshih@realtek.com
Add function to get and parse BT polluted counter.
When WLAN Tx was dropped by BT, the packet will be marked as BT polluted.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211209083229.10815-4-pkshih@realtek.com
The AXIDMA is tx/rx packet transmission between PCIE host
and device, and TX FIFO is MAC TX data.
We dump them to verify that these memory buffers are correct.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211122021129.4339-1-pkshih@realtek.com
This driver named rtw89, which is the next generation of rtw88, supports
Realtek 8852AE 802.11ax 2x2 chip whose new features are OFDMA, DBCC,
Spatial reuse, TWT and BSS coloring; now some of them aren't implemented
though.
The chip architecture is entirely different from the chips supported by
rtw88 like RTL8822CE 802.11ac chip. First of all, register address ranges
are totally redefined, so it's impossible to reuse register definition. To
communicate with firmware, new H2C/C2H format is proposed. In order to have
better utilization, TX DMA flow is changed to two stages DMA. To provide
rich RX status information, additional RX PPDU packets are added.
Since there are so many differences mentioned above, we decide to propose
a new driver. It has many authors, they are listed in alphabetic order:
Chin-Yen Lee <timlee@realtek.com>
Ping-Ke Shih <pkshih@realtek.com>
Po Hao Huang <phhuang@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Vincent Fann <vincent_fann@realtek.com>
Yan-Hsuan Chuang <tony0620emma@gmail.com>
Zong-Zhe Yang <kevin_yang@realtek.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211008035627.19463-1-pkshih@realtek.com
