In order to set channel info to hal during HW scan, we add the update
channel flow to support setting by parameters to meet the HW scan
requriement.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809084107.38137-4-pkshih@realtek.com
Since chip_info has became const table, we must access them via const
pointer to avoid invalid writing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065232.28510-1-pkshih@realtek.com
Some WSC IEs require size larger than we current supports. Extend size
to fit those demands. Separate the registered scan IE length by IC so
settings can be independent.
Since old firmware uses fewer page number, define a firmware feature to
be compatible with various firmware version.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065003.28340-2-pkshih@realtek.com
The function alloc_workqueue() in rtw_core_init() can fail, but
there is no check of its return value. To fix this bug, its return value
should be checked with new error handling code.
Fixes: fe101716c7 ("rtw88: replace tx tasklet with work queue")
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: William Dean <williamsukatube@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220723063756.2956189-1-williamsukatube@163.com
Start making some SMPS related code MLD-aware. This isn't
really done yet, but again cuts down our 'deflink' reliance.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here's a first set of patches for v5.20. This is just a
queue flush, before we get things back from net-next that
are causing conflicts, and then can start merging a lot
of MLO (multi-link operation, part of 802.11be) code.
Lots of cleanups all over.
The only notable change is perhaps wilc1000 being the
first driver to disable WEP (while enabling WPA3).
-----BEGIN PGP SIGNATURE-----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=E0Dx
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-06-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
wireless-next patches for v5.20
Here's a first set of patches for v5.20. This is just a
queue flush, before we get things back from net-next that
are causing conflicts, and then can start merging a lot
of MLO (multi-link operation, part of 802.11be) code.
Lots of cleanups all over.
The only notable change is perhaps wilc1000 being the
first driver to disable WEP (while enabling WPA3).
* tag 'wireless-next-2022-06-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (29 commits)
wifi: mac80211_hwsim: Directly use ida_alloc()/free()
wifi: mac80211: refactor some key code
wifi: mac80211: remove cipher scheme support
wifi: nl80211: fix typo in comment
wifi: virt_wifi: fix typo in comment
rtw89: add new state to CFO state machine for UL-OFDMA
rtw89: 8852c: add trigger frame counter
ieee80211: add trigger frame definition
wifi: wfx: Remove redundant NULL check before release_firmware() call
wifi: rtw89: support MULTI_BSSID and correct BSSID mask of H2C
wifi: ray_cs: Drop useless status variable in parse_addr()
wifi: ray_cs: Utilize strnlen() in parse_addr()
wifi: rtw88: use %*ph to print small buffer
wifi: wilc1000: add IGTK support
wifi: wilc1000: add WPA3 SAE support
wifi: wilc1000: remove WEP security support
wifi: wilc1000: use correct sequence of RESET for chip Power-UP/Down
wifi: rtlwifi: fix error codes in rtl_debugfs_set_write_h2c()
wifi: rtw88: Fix Sparse warning for rtw8821c_hw_spec
wifi: rtw88: Fix Sparse warning for rtw8723d_hw_spec
...
====================
Link: https://lore.kernel.org/r/20220610142838.330862-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add this check to avoid crash by dereferencing a null pointer. When hwscan
fails due to no memory or dma failure, the scan flag in ieee80211_local is
cleared. So mac80211 determine that it's not hw_scan then calls
sw_scan_complete() with null vif, which is also freed during the fail.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220520081523.45987-1-pkshih@realtek.com
Each chip have best ampdu density value, the correct setting can improve
throughput performance.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220428020521.8015-1-pkshih@realtek.com
To support stations in power saving mode, AP should notify stations
that there are frames buffered at the AP via TIM during beacons.
Driver used to transmit identical beacons that were downloaded to
hardware during the initiation phase. This beacon will become
obsolete over time.
If the beacon does not contain sufficient information, station would
not be able to percept that there is data to receive. Hence it won't
wake up and start the PS-poll procedure, this could lead to timeout
and/or lost data segments. In order to resolve this issue, driver will
now download beacon to hardware whenever the content is updated.
Enable hardware to update dtim_count for more efficiency, this reduces
the overhead of downloading beacon at every beacon interval since most
of the time only the dtim_count needs to be updated.
Change queue mapping for broadcast/multicast frames to high queue, so
these frames can be prioritized and sent when dtim_count is zero.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-4-pkshih@realtek.com
Adding this allows us to get notification when bitrate configuration
of the station changes. Update according parameters to firmware so
the rate control algorithm can work properly.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-2-pkshih@realtek.com
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously we only consider single interface's status, idle mode
behavior could be unexpected when multiple interfaces is active.
Change to enter/leave idle mode by mac80211's configuration state.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318034316.40720-1-pkshih@realtek.com
In order to recognize the gaming controller HID, make a C2H/H2C/Mailbox
handshake to collect all the connected information from BT.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220215004855.4098-6-pkshih@realtek.com
If BT PTA counter can not update regularly, it will lead coex mechanism
run into some unexpected state.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220215004855.4098-4-pkshih@realtek.com
In some case, wifi chip need to be configed to be TX/RX 1ss mode.
For this mode, wifi components, such as MAC/BB/RF, need to be
specially set, and driver need to send SMPS action frame to inform AP.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220215004855.4098-2-pkshih@realtek.com
Some APs like CMW270 only support one phyrate and the function
rtw_update_rate_mask could disable that rate. To fix such problem, we
restore the rate mask if we find that the rate_mask is empty.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220208082427.42433-2-pkshih@realtek.com
Upon hw scan completion, idle mode is not re-entered. This might
increase power consumption under no link mode. Fix this by adding the
re-enter flow. We need another work for this since enter_ips waits
for c2h_work to finish, which might lead to deadlock if caller is in
the same work.
Fixes: 10d162b2ed ("rtw88: 8822c: add ieee80211_ops::hw_scan")
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220121070813.9656-3-pkshih@realtek.com
Register cfg80211_sar_capa with type NL80211_SAR_TYPE_POWER and four
frequency ranges for configurations in unit of 0.25 dBm. And handle
callback set_sar_specs.
Originally, TX power has three main parameters, i.e. power base,
power by rate, and power limit. The formula can be simply considered
as TX power = power base + min(power by rate, power limit). With the
support of SAR which can be treated as another power limit, there is
one more parameter for TX power. And the formula will evolve into
TX power = power base + min(power by rate, power limit, power sar).
Besides, debugfs tx_pwr_tbl is also refined to show SAR information.
The following is an example for the difference.
Before supporting SAR,
-----------------------------------
...
path rate pwr base (byr lmt ) rem
A CCK_1M 66(0x42) 78 -12 ( 12 -12) 0
A CCK_2M 66(0x42) 78 -12 ( 8 -12) 0
...
-----------------------------------
After supporting SAR and making some configurations,
-----------------------------------
...
path rate pwr base (byr lmt sar ) rem
A CCK_1M 62(0x3e) 78 -16 ( 12 -12 -16) 0
A CCK_2M 62(0x3e) 78 -16 ( 8 -12 -16) 0
...
-----------------------------------
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211220093656.65312-1-pkshih@realtek.com
Declare this function allows us to use customized scanning policy.
By doing so we can be more time efficient on each scan. In order to
make existing coex mechanism work as usual, firmware notifies driver
on each channel switch event, then decide antenna ownership based on
the current channel/band. Do note that this new mechanism affects
throughput more than the sw_scan we used to have, but the overall
average throughput is not affected since each scan take less time.
Since the firmware size is limited, we only support probe requests
with custom IEs length under 128 bytes for now, if any user space
tools requires more than that, we'll introduce related changes
afterwards. For backward compatibility, we fallback to sw_scan when
using older firmware that does not support this feature.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221085010.39421-1-pkshih@realtek.com
These settings enables mac to detect and recover when rx fifo
circuit deadlock occurs. Previous version missed this, so we fix it.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217012708.8623-1-pkshih@realtek.com
It is useful to fix the bit rate of TX packets. For example, if
someone is measuring the TX power, or debugging with the issues
of the TX throughput on the field.
To set the value of fixed rate, one should input corresponding
desc rate index (ex, 0x0b for DESC_RATE54M to fix at 54 Mbps).
Set a value larger than DESC_RATE_MAX will disable fix rate, so
the rate adaptive mechanism can resume to work.
Example,
To fix rate at MCS 1:
echo 0x0d > /sys/kernel/debug/ieee80211/phy0/rtw88/fix_rate
To not to fix rate:
echo 0xff > /sys/kernel/debug/ieee80211/phy0/rtw88/fix_rate
To know which rate was fixed at:
cat /sys/kernel/debug/ieee80211/phy0/rtw88/fix_rate
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211129020506.6273-1-pkshih@realtek.com
The usage of fw_crash debugfs is to write 1 to it to trigger fw crash
simulation and to read from it to check the state. When zero is read,
it is supposed to mean fw crash/restart process is done. Then, some
test plans can be designed for crash/restart.
e.g.
step 1. trigger fw crash simulation
step 2. poll the state until zero is read
step 3. check connection by ping test
However, in certain connection cases, triggering fw crash simulation
will take a while. If the state is queried too early before restart
begins processing, it may mistakenly think restart process has been
done. If some tests are started at this time, something unexpected
might happen due to the follow-up restart process.
To avoid that, let fw_crash also show non-zero when a simulation
is still triggering.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211001082301.4805-1-pkshih@realtek.com
Add Energy Detected CCA (EDCCA) mechanism to detect energy on the channel.
And EDCCA support adaptivity mode now. From MIC Ordinance Regulating Radio
Equipment article 49.20, ETSI EN-300-328 and EN-301-893, the device should
be able to dynamically pause TX activity when energy detected on the air.
According to ETSI/JP DFS region, driver will set corresponding threshold
and stop TX activity if the detected energy exceeds the threshold. For now,
we support it on 8822b and 8822c first.
By default, EDCCA mechanism is turned on. For ETSI/JP DFS region, it will
turn to adaptivity mode. However, with adaptivity, if environment is too
noisy, TX may often be halted. So, a debugfs for EDCCA is added. It can
show what EDCCA mode is used currently. And EDCCA mechanism can be turned
on/off through the debugfs while debugging.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-4-pkshih@realtek.com
Realtek chips can program a specific country domain on efuse to
indicate what is the expected rtw_regulatory. For chips with a
programmed country domain, we set REGULATORY_STRICT_REG to tell
stack to consider follow-up regulatory_hint() as the superset of
our regulatory rule. Besides, on driver side, only the request via
NL80211_REGDOM_SET_BY_DRIVER, which matches programmed country
domain, will be handled to keep rtw_regulatory unchanged.
For worldwide roaming chips, i.e. ones without a specific programmed
country domain, system of distro can set expected regulatory via
NL80211_REGDOM_SET_BY_USER. With setting from it, rtw_regulatory
will handle the requests only via NL80211_REGDOM_SET_BY_USER to
follow setting from system of distro. REGULATORY_COUNTRY_IE_IGNORE
will then be set to tell stack to ignore country IE for us. The
restrictions mentioned above will remain until 00, i.e. worldwide,
is set via NL80211_REGDOM_SET_BY_USER.
On the other hand, for worldwide roamin chips, if there is no
specific regulatory set via NL80211_REGDOM_SET_BY_USER, requests
from all regulatory notifications will be handled by rtw_regulatory.
And REGULATORY_COUNTRY_IE_IGNORE won't be set.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-3-pkshih@realtek.com
Enabling this improves tx performance for long distance transmission.
We used to enable stbc by the rx stbc cap of the associated station.
But rx cap will be masked out in ieee80211_ht_cap_ie_to_sta_ht_cap
if we do not declare tx stbc.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210713104524.47101-2-pkshih@realtek.com
Fix erroneous code that leads to unreferenced objects. During H2C
operations, some functions returned without freeing the memory that only
the function have access to. Release these objects when they're no longer
needed to avoid potentially memory leaks.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210624023459.10294-1-pkshih@realtek.com
Use device coredump framework instead of print_hex_dump to support
FW crash dump. Pass data to the framework if preparing and dumping
are successful. The framework will take the ownership of the data.
The data will be freed after the framework determines its lifetime
is over. A new coredump will not work if the previous one still
exists.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210528032901.12927-2-pkshih@realtek.com
It is found that driver scan could be affected by dynamic mechanism
of firmware, so we notify firmware to stop it in the scan period.
Another, firmware will detect the background noise and report to
driver for further use.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210514075517.14216-3-pkshih@realtek.com
add api to check if a certain feature is supported.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210514075517.14216-2-pkshih@realtek.com
Adding this supports beacon filter and CQM.
Let firmware perform connection quality monitor and beacon processing.
This make host CPU wakeup less under power save mode.
To make mechanisms work as usual, fw will notify driver events such as
signal change and beacon loss.
This feature needs firmware 9.9.8 or newer to support it, and driver is
compatible with older firmware.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210426013252.5665-1-pkshih@realtek.com
Although FW crash logs are already supported for dumping in driver, the
logs may not be sufficient to analyze field issues. To improve this part,
we add a support to dump FW memory.
When driver receives FW crash notifications, driver uses DDMA, which is a
HW ability, to copy specified FW memory to FW fifo. Driver can then dump
these information from FW fifo. With this support, not only FW crash log
but also specified FW memory will be dumped while FW crash. Besides,
specified registers are also dumped.
This feature is implemeted on 8822C first due to difference of FW layouts
between ICs. In addition, we add a debugfs to trigger FW crash. It can
simulate the process of crash, dump and reset. Through it, we can also
check if a reset is ongoing.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210309060121.9099-1-pkshih@realtek.com
The variable ret is defined at the beginning and initialized
to 0 until the function returns ret, and the variable ret is
not reassigned.Therefore, we do not need to define the variable
ret, just return 0 directly at the end of the function.
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210223075438.13676-1-samirweng1979@163.com
Clear WL/BT on/off bit in scoreboard register that is used to exchange
WL/BT status. Since the status is preserved after warm reboot, we must
clear it when WL is going to down.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210219054140.7835-1-pkshih@realtek.com
Replace tasklet so we can do tx scheduling in parallel. Since throughput
is delay-sensitive in most cases, we allocate a dedicated, high priority
wq for our needs.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-5-pkshih@realtek.com
Register rrsr determines the response rate we send.
In field tests, using rate higher than current tx rate could lead
to difficulty for the receiving end to receive management/control
frames. Calculate current modulation level by tx rate then cross out
rate higher than those.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-2-pkshih@realtek.com
RFE type2 is a new NIC which has one RF antenna shares with BT.
Update phy parameter to verstion V57 to allow initial procedure
to load extra AGC table for sharing antenna NIC.
Signed-off-by: Guo-Feng Fan <vincent_fann@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210202055012.8296-4-pkshih@realtek.com
The parameter of kfree function is NULL, so kfree code is useless, delete it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201216130442.13869-1-zhengyongjun3@huawei.com
When driver was developed, FCC regulation didn't enable channel 144
and there was no demand for channel 144 at that time. Although HW
actually supports channel 144, driver didn't announce channel 144.
Therefore, channel 144 (20 MHz), channel 142 (40 MHz) and channel
138 (80 MHz) couldn't be used.
Today, channel 144 has been enabled by regulations and
is gradually being supported. With test requirements,
we declare hw supports channel 144.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201204013823.3729-1-pkshih@realtek.com
Some AP will not follow the power save request, or it cannot stop
transmission until its queue is empty. It may bring the decreasing of
data rate.
WLAN firmware will count is the AP still leaked packet after power save
handshake was done or not to enable WLAN slot extend mechanism.
The extend WLAN slot mechanism will extend the WLAN slot after power save
handshake, 5 ms per times, maximum is 5 times to received the leaked packet
to avoid the rate lower down.
And if the transmission was already locked at CCK rate.
The extended WLAN slot can also increase the opportunity that we can
received the CCK's long packet and be released from CCK rate.
While BT multi-link status was finished, there is possible that it still
has some packet remained for seconds. Add a timer to remain the multi-link
mechanism to protect WLAN Rx.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-8-pkshih@realtek.com
The original mechanism may cause A2DP glitch during WiFi connecting AP.
Because the original TDMA may decrease too much A2DP slot.
This patch add a timer and variable to let the case A2DP + WL_Connecting
performed more well.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-9-pkshih@realtek.com
Adjust space and comments, and fix "line over 80 characters" warnings
reported by checkpatch.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-5-pkshih@realtek.com
This patch checks the supported lps deep mode from firmware feature,
and allows different firmware have different deep power mode.
Original module parameter rtw_fw_lps_deep_mode is replaced with
rtw_disable_lps_deep_mode for user to disable lps deep mode.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-5-tehuang@realtek.com
Originally driver checks if firmware has left lps via reading the setting
of REG_TCR register. But this way may fail when firmware is frequently
changing power state. Therefore, firmware provides a safer option for
driver. When firmware leaves lps successfully, it sends a C2H response
to inform driver.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-4-tehuang@realtek.com
Some functions need the support of firmware with special version.
In order to get the feature of current firmware, we store the information
in firmware header and parse after firmware is loaded. The current feature
list in firmware header includes checking leave lps via C2H and
supported lps deep mode.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-3-tehuang@realtek.com
This patch adds a function which is able to dump firmware fifo when
firmware crashes. If firmware needs more than one time to dump all logs,
it will set a bit called "more bit" in the header of the first log, and
driver needs to set a register to inform firmware that it is ready for the
next dump.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-5-tehuang@realtek.com
This handles the situation when firmware crashes.
When firmware crashes, it will send an interrupt, and driver will queue
a work for recovery.
In the work, driver will reset it's internal association state, which
includes removing associated sta's macid, resetting vifs' states
and removing keys. After resetting the driver's state, driver will call
rtw_enter_ips() to force the chipset power off to reset the chip.
Finally, driver calls ieee80211_restart_hw() to inform mac80211 stack
to restart.
Since only 8822c firmware supports this feature, the interrupt will only
be triggered when 8822c chipset is loaded.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-3-tehuang@realtek.com
If rtw_core_init() fails to load the wow firmware, rtw_core_deinit()
will not get called to clean up the regular firmware.
Ensure that an error loading the wow firmware does not produce an oops
for the regular firmware by waiting on its completion to be signalled
before returning. Also release the loaded firmware.
Fixes: c8e5695eae ("rtw88: load wowlan firmware if wowlan is supported")
Cc: Chin-Yen Lee <timlee@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200920132621.26468-3-afaerber@suse.de
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly
and remove .data field.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-16-allen.cryptic@gmail.com
Fix the transmission is not sent with short GI under
some conditions even if the receiver supports short GI.
If VHT capability IE exists in the beacon, the original
code uses the short GI for 80M field as driver's short GI
setting for transmission, even the current bandwidth is
not 80MHz.
Short GI supported fields for 20M/40M are informed in HT
capability information element, and short GI supported
field for 80M is informed in VHT capability information
element.
These three fields may be set to different values.
Driver needs to record each short GI support field for
each bandwidth, and send correct info depends on current
bandwidth to the WiFi firmware.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-3-yhchuang@realtek.com
Add a set of logic with corresponding coexistence parameters to
handle the situation under BT inquiry/page.
We will set PSTDMA while WL-Busy + BT inquiry/page to separate
WL/BT slots. PSTDMA can protect WL data rate and BT performance.
If WL-Busy + BT inquiry/page and there was BT device paired,
We will set the mechanism to 4Slot PSTDMA.
In 4Slot PSTDMA, the paired devices can perform more smoothly
and prevent some issues trigger from insufficient data.
And to avoid A2DP glitch or disconnection, we will adjust ACL
data priority higher than inquiry/page.
In addition, we found sometimes BT inquiry/page still working
last for seconds after BT had notified inquiry/page finished.
It will lead to A2DP glitch cause of ACL data, inquiry/page
priority toggled. To fix the corner, we add a timer to remain
the inquiry/page status.
And we found WL busy/idle threshold is too sensitive,
it will keep switching in some weak network environment and
coexistence mechanism will switch between TDMA and PSTDMA.
The very frequently switching may destroyed not only the
handshake with AP, but BT performance. And it will trigger
some unexpected error.
To prevent the frequently switching, we add a timer to delay
the status change while WL busy switch to idle.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200715023324.8600-1-yhchuang@realtek.com
Since single rf path chips don't support TX SPBC, tell mac80211
to not advertise it.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-5-yhchuang@realtek.com
8821c is capable of 2.4G and 5G.
Implement rtw_chip_ops::set_channel() to set 2G and 5G channels.
This includes MAC, BB and RF related settings.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-5-yhchuang@realtek.com
Connecting to an AP with WPA2 security may fail. The IQK
and the EAPOL 4-way handshake may overlap because the
driver does IQK right after assoc success.
For 802.11n devices, the IQK is done in the driver and it
could require more than 100ms to complete. During IQK, any
TX/RX events are paused. So if the EAPOL 4-way handshake
started before IQK finished, then the 1/4 and 2/4 part of
the handshake could be dropped. The AP will then issue
deauth with reason IEEE8021X_FAILED (23).
To resolve this, move IQK routine into managed TX prepare
(ieee80211_ops::mgd_prepare_tx()). The callback is called
before the managed frames (auth/assoc) are sent. This will
make sure that the IQK is completed before the handshake
starts. But don't do IQK during scanning because doing it
on each channel will take too long.
For 802.11ac devices, the IQK is done in firmware and it
takes less time to complete. Therefore we don't see a
failure during the EAPOL 4-way handshake. But it is still
worth moving the IQK into ieee80211_ops::mgd_prepare_tx().
Fixes: f5df1a8b43 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-4-yhchuang@realtek.com
Some chips are not able to receive LDPC packets. Add an attribute
to rtw_chip_info to determine if the LDPC capability in [ht/vht]_cap
should be advertised or not.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-6-yhchuang@realtek.com
The WLAN CPU of 8723D device is different from others, add legacy
firmware download function for it. A new variable wlan_cpu is used to
decide which firmware download function we should use.
Legacy firmware file contains 32 bytes header including version and
subversion. When downloading to wlan cpu, header is excluded.
Firmware is downloaded via beacon queue to reserved page that is a part of
TX buffer. Since 11N WLAN CPU uses different control registers, this patch
introduces related control registers.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-2-yhchuang@realtek.com
8723D use SIPI to indirectly read RF register instead of directly read,
so introduce a new struct rtw_rf_sipi_addr and new function
rtw_phy_read_rf_sipi(). Since other chips don't use the new function,
only 8723D needs to fill struct rtw_rf_sipi_addr in rtw_chip_info.
Because there are two kinds of functions for reading RF registers now,
change rtw_phy_read_rf() to chip->ops->read_rf() in
rtw_phy_write_rf_reg_sipi() so that we can switch tp proper RF read
functions depends on the type of the chip.
Though 8723D is an 1x1 chip, it has two RF PHY and we can switch to
one of them, and that should be configured properly. Hence, add a
fix_rf_phy_num to struct rtw_chip_info to allow driver to set one of
the PHY's registers for 8723D, even it is only 1x1. Another variable
rf_phy_num is introduced to keep the constraint number of RF path we
can access, and its value is:
rf_phy_num = (fix_rf_phy_num ? fix_rf_phy_num : rf_path_num)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420055054.14592-5-yhchuang@realtek.com
8723D doesn't support beamform because rtw88 only supports VHT beamform
but 8723d doesn't have VHT capability. Though 8723d doesn't support
beamform, BSS_CHANGED_MU_GROUPS is still marked as changed when doing
disassociation. So, add wrapper functions for all beamform ops to make
sure they aren't NULL before calling.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420055054.14592-3-yhchuang@realtek.com
User space program such as iw can set antenna mask for the device.
So add set antenna support by configure the trx mode.
This is useful for some tests want to see the output of different
antenna configuration (e.g. path A v.s. path B).
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410100950.3199-3-yhchuang@realtek.com
Each device has only one reserved page shared with all of the
vifs, so it seems not reasonable to pass vif as one of the
arguments to rtw_fw_download_rsvd_page(). If driver is going
to run more than one vif, the content of reserved page could
not be built for all of the vifs.
To fix it, let each vif maintain its own reserved page list,
and build the final reserved page to download to the firmware
from all of the vifs. Hence driver should add reserved pages
to each vif according to the vif->type when adding the vif.
For station mode, add reserved page with rtw_add_rsvd_page_sta().
If the station mode is going to suspend in PNO (net-detect)
mode, remove the reserved pages used for normal mode, and add
new one for wowlan mode with rtw_add_rsvd_page_pno().
For beacon mode, only beacon is required to be added using
rtw_add_rsvd_page_bcn().
This would make the code flow simpler as we don't need to
add reserved pages when vif is running, just add/remove them
when ieee80211_ops::[add|remove]_interface.
When driver is going to download the reserved page, it will
collect pages from all of the vifs, this list is maintained
by rtwdev, with build_list as the pages' member. That way, we
can still build a list of reserved pages to be downloaded.
Also we can get the location of the pages from the list that
is maintained by rtwdev.
The biggest problem is that the first page should always be
beacon, if other type of reserved page is put in the first
page, the tx descriptor and offset could be wrong.
But station mode vif does not add beacon into its list, so
we need to add a dummy page in front of the list, to make
sure other pages will not be put in the first page. As the
dummy page is allocated when building the list, we must free
it before building a new list of reserved pages to firmware.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200312080852.16684-4-yhchuang@realtek.com
Remove unused fab_version member from struct rtw_hal.
Some of the checks being made were nonsense.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware value of secondary channel offset isn't very intuitive. This
commit adds enumeration, so we can easier to check the logic with the
suffix of enumeration name, likes _UPPER or _LOWER.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver could possibly be dead-locked while canceling works with
*_sync() with mutex lock held. Those cancel_delayed_work_sync()
functions will wait until the work is done, but if we hold the
lock, they will never acquire the lock.
To prevent this, simply release the lock and acquire again after
the works have been canceled. And to avoid the works being queued
again, check if the device is at RTW_FLAG_RUNNING state, otherwise
just return and do nothing.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix typo, should use rtw_hci_stop()
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
dm_lock is never used. Thus, remove this redundant spinlock.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The rate mask is used to tell firmware the supported rate depends on
negotiation. We loop 2 times for all VHT/HT 2SS rate mask first, and then
only keep the part according to chip's NSS.
This commit fixes the logic error of '&' operations for VHT/HT rate, and
we should run this logic before adding legacy rate.
To access HT MCS map, index 0/1 represent MCS 0-7/8-15 respectively. Use
NL80211_BAND_xxx is incorrect, so fix it as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Net-detect is an option of wowlan to allow the device to
be woken up from suspend mode when configured network is detected.
When user enables net-detect and lets the device enter suspend
state, wowlan firmware will periodically scan until beacon or
probe response of configured networks are received.
Between two scans, wowlan firmware keeps wifi chip in idle mode
to reduce power consumption. If configured networks are detected,
wowlan firmware will trigger resume process.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wake on WLAN(wowlan) is a feature which allows devices
to be woken up from suspend state through wlan events.
When user enables wowlan feature and then let the device
enter suspend state, wowlan firmware will be loaded by
the driver and periodically monitors wifi packets.
Power consumption of wifi chip will be reduced in this
state.
If wowlan firmware detects that specific wlan event
happens, it will issue wakeup signal to trigger resume
process. Driver will load normal firmware and let wifi
chip return to the original state.
Currently supported wlan events include receiving magic packet,
rekey packet and deauth packet, and disconnecting from AP.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver used to download normal firmware only,
but some devices support wowlan and require to
download wowlan firmware when system suspends.
So modify rtw_load_firmware() and its callback to
allow driver to download both normal and wowlan firmware.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver could access a NULL firmware pointer if we don't
return here.
Fixes: 5195b90426 ("rtw88: avoid FW info flood")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The FW info was printed everytime driver is powered on, such as
leaving IDLE state. It will flood the kernel log.
Move the FW info printing to callback when FW is loaded, so
that will only be printed once when device is probed.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This fixes compile warning:
In file included from include/linux/bitops.h:5:0,
from include/linux/kernel.h:12,
from include/asm-generic/bug.h:19,
from arch/mips/include/asm/bug.h:42,
from include/linux/bug.h:5,
from include/net/mac80211.h:16,
from drivers/net/wireless/realtek/rtw88/main.h:8,
from drivers/net/wireless/realtek/rtw88/main.c:5:
drivers/net/wireless/realtek/rtw88/main.c: In function 'rtw_update_rate_mask':
include/linux/bits.h:23:11: warning: right shift count is negative
[-Wshift-count-negative]
(~UL(0) >> (BITS_PER_LONG - 1 - (h))))
^
drivers/net/wireless/realtek/rtw88/main.c:622:17: note: in expansion of macro 'GENMASK'
u64 cfg_mask = GENMASK(63, 0);
^~~~~~~
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: f39e9bd49a ("rtw88: add set_bitrate_mask support")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This commit adds several Tx/Rx physical information to phy_info
debugfs for 8822B/8822C. By this debugfs, we can know physical
information, such as Tx/Rx rate, RSSI, EVM,SNR, etc. The
information is gotten from the packets of Tx/Rx path. It has
no impact for the performance of 8822B/8822C.
In the fields, we may meet different kinds of problems, but
we may have no professional instrument to check them. At
this moment, this debugfs is a good tool, and it may provide
useful information for debug.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support setting bit rate from upper layer.
After configuring the original rate control result in the driver, the
result is then masked by the bit rate mask received from the ops
set_bitrate_mask. Lastly, the masked result will be sent to firmware.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable MU-MIMO transmit beamformee support for chipset 8822b and 8822c.
If the driver is in station mode and associated with an AP, and the
capabilities of both meet the requirement of beamforming, driver will
run as a beamformee and the corresponding chip settings will be set.
In addition, module parameter support_bf is added to enable or disable
beamforming. Sometimes driver will need to disable for inter-operate
issues, and it would be easier for driver to debug.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 feature.
According to the "Hardware crypto acceleration" documentation section,
when set_key() is called with %DISABLE_KEY command, for outgoing frames,
we flush out frames in the queues with the old key; for incoming frames,
no frames will be passed to mac80211 decrypted with the old key due to
rtw_sec_clear_cam().
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Disable efuse if the efuse is enabled when we failed to setup the efuse
information, otherwise the hardware will not turn off.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8822C is a 2x2 11ac chip, and then NSS must be less or equal to 2. However,
current nss of hw cap is 3, likes
hw cap: hci=0x0f, bw=0x07, ptcl=0x03, ant_num=7, nss=3
This commit adds constraint to make sure NSS <= rf_path_num, and result
looks like
hw cap: hci=0x0f, bw=0x07, ptcl=0x03, ant_num=7, nss=2
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Based on the mac80211's TXQ implementation, TX-AMSDU can
be used to get higher MAC efficiency. To make mac80211
aggregate MSDUs, low level driver just need to leave skbs
in the TXQ, and mac80211 will try to aggregate them if
possible. As driver will schedule a tasklet when the TX
queue is woke, until the tasklet being served, there will
have some skbs in the queue if traffic is heavy.
Driver can control the max AMSDU size depending on the
current bit rate used by hardware/firmware. The higher
rates are used, the larger AMSDU size can be.
It is tested that can achieve higher T-Put at higher rates.
If the environment is relatively clean, and the bit_rate
is high enough, we can get about 80Mbps improvement.
For lower bit rates, not much gain can we get, so leave
the max_amsdu length low to prevent aggregation.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever the firmware increases/decreases the bit rate used
to transmit to a peer, it sends an RA report through C2H to
driver. Driver can then record the bit rate in the peer's
struct rtw_sta_info, and report to mac80211 when it asks us
for the statistics of the sta by ieee80211_ops::sta_statistics
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We can indicate IEEE80211_HW_HAS_RATE_CONTROL to mac80211 because
the hardware has its own rate control algorithm. And what driver needs
to do is to choose an RA mask according the peer's capabilities.
But the hardware is not able to setup BA session by itself. So driver
requires to initiate tx BA session for hardware, and tells it if it is
possible to transmit AMPDU. The hardware can then aggregate MPDUs.
And the size of AMPDU is controlled by the TX descriptor and the
register value. Since the TX descriptor will reference the max AMPDU
size from ieee80211_sta::ht_cap::ampdu_factor, just set the register
value to 0x3f, and let it be controlled by TX descriptor.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The mac80211 provides software TX queue for driver, as long as
driver has hooked ieee80211_ops::wake_tx_queue. Each time a
packet is queued onto the TX queue, that queue will be woken
up the inform driver to serve the queue.
Now driver only supports PCI interface ICs, there's no specific
traffic control for each queue, just schedule a tasklet, and
dump all of the packets at once to the DMA ring. Instead of TX
the packets whenever TX queue is woke, tasklet handler can have
more packets dumped to the device, takes advantage of burst
write with DMA engine.
And if the driver is going to support USB/SDIO ICs, the tasklet
can be more flexible for aggregating the packets, enhance the
efficiency of bandwidth usage.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The module parameter rtw_fw_support_lps is misleading. It
is not used to represent the firmware's property, but to
determine if driver wants to ask firmware to enter LPS.
However, driver should better enable/disable PS through
cfg80211_ops::set_power_mgmt instead.
For example, one could use iw command to set PS state.
$ sudo iw wlanX set power_save [on/off]
So rtw_fw_support_lps should be removed because it is
misleading and useless. Instead of checking the parameter,
set PS mode according to IEEE80211_CONF_PS.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a module parameter to select deep PS mode. And the mode
cannot be changed after the module has been inserted and probed.
If anyone wants to change the deep mode, should change the mode
and probe the device again to setup the changed deep mode.
When the device is probed, driver will check the deep PS mode
with different IC's PS mode suppotability. If none of the
PS mode is matched, the deep PS mode is changed to NONE,
means deep PS is disabled.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Deep power save allows firmware/hardware to operate in a
lower power state. And the deep power save mode depends on
LPS mode. So, before entering deep PS, driver must first
enter LPS mode.
Under Deep PS, most of hardware functions are shutdown,
driver will not be able to read/write registers and transfer
data to the device. Hence TX path must be protected by each
interface. Take PCI for example, DMA engine should be idle,
and no nore activities on the PCI bus.
If driver wants to operate on the device, such as register
read/write, it must first acquire the mutex lock and wake
up from Deep PS, otherwise the behavior is undefined.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dynamic mechanism requires BB/RF working to adjust
hardware settings. But PS state periodically turns
off BB/RF, could lead to wrong setting.
So leave PS state before DM to make sure it works.
And then check if we can enter PS state again.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Protect LPS enter/leave routine with rtwdev->mutex.
This helps to synchronize with driver's states correctly.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The original design of LPS enter/leave routines allows
to control the LPS state by each interface. But the
hardware cannot actually handle it that way. This means
the hardware can only enter LPS once with an associated
port, so there is no need to keep tracking the state of
each vif.
Hence the logic of enter/leave LPS state can be simple,
just to check the state of the device's flag. And for
leaving LPS state, it will get the same port id to send
to inform the hardware.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove PS related *_irqsafe functions to avoid entering/leaving PS
under interrupt context. Instead, make PS decision in watch_dog.
This could simplify the logic and make the code look clean.
But it could have a little side-effect that if the driver is having
heavy traffic before the every-2-second watch_dog detect the traffic
and decide to leave PS, the thoughput will be lower. Once traffic is
detected by watch_dog and left PS state, the throughput will resume
to the peak the hardware ought to have again.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These helper functions seems useless. And in some cases
we want to use test_and_[set/clear]_bit, these helpers
will make the code more complicated. So remove them.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After firmware has been downloaded, driver should send
some information to it through H2C commands. Those H2C
commands are transmitted through TX path.
But before HCI has been started, the TX path is not
working completely. Such as PCI interfaces, the interrupts
are not enabled, hence TX interrupts will not be issued
after H2C skb has been DMAed to the device. And the H2C
skbs will not be released until the device is powered off.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware has enough buffer to receive like 8K for an MPDU.
So tell mac80211 that we can receive AMSDU in AMPDU.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Both RTL8822BE/RTL8822CE are WiFi + BT combo chips. Since
WiFi and BT use 2.4GHz to transmit, it is important to
make sure they run concurrently without interfering each
other. To achieve this, WiFi driver requires a mechanism
to collaborate with BT, whether they share the antenna(s)
or not.
The final decision made by the co-existence mechanism is
to choose a proper strategy, or called "tdma/table", and
inform either firmware or hardware of the strategy.
To choose a strategy, co-existence mechanism needs to
have enough information from WiFi and BT.
BT information is provided through firmware C2H.
The contents describe the current status of BT, such as
if BT is connected or is idle, or the profile that is
being used.
WiFi information can be provided by WiFi itself. The WiFi
driver will call various of "notify" functions each time
the state of WiFi changed, such as WiFi is going to switch
channel or is connected. Also WiFi driver can know if it
shares antenna with BT by reading efuse content. Antenna
configuration of the module will finally get a different
strategy.
Upon receiving any information from WiFi or BT, the WiFi
driver will run the co-existence mechanism immediately.
It will set the RF antenna configuration according to the
strategy through the TDMA H2C to firmware and a hardware
table. Based on the tdma/table, WiFi + BT should work with
each other, and having a better user experience.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since this macro definition has different values in different chipset,
the current defined macro value is for 8822b. This will cause the
settings of 8822c be incorrect.
Remove RTW_MAX_POWER_INDEX and use max_power_index in struct rtw_chip_info
to make sure the value of different chipset is right.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If phy rate is decreased, sub bandwidth may be chosen by RA.
We consider possible power limits and apply the min one;
otherwise, the tx power index may be larger than spec.
And we cross-reference power limits of vht and ht with
20/40M bandwidth in 5G to avoid values are not assigned.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
