The RTL8821AU firmware sends C2H_BT_INFO by itself when bluetooth
headphones are connected, but not when they are disconnected. This leads
to the coexistence code still using the A2DP algorithm long after the
headphones are disconnected, which means the wifi speeds are much lower
than they should be. Work around this by asking for updates every two
seconds if the chip is RTL8821AU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/358acdd2-6aae-46c1-9c66-fcce4e700b96@gmail.com
All the chips currently supported have a "scoreboard": the chip keeps
track of certain things related to bluetooth, for example, whether
bluetooth is active. The information can be read from register 0xaa.
RTL8821AU doesn't have this. Implement bluetooth activity detection in
rtw_coex_monitor_bt_enable() based on the bluetooth TX/RX counters.
This is mostly important for RTL8811AU, the version of RTL8821AU without
bluetooth. Without this change, the driver thinks bluetooth is active
and the wifi speeds are low.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/5058f23d-2086-42cd-82ad-eef31a348467@gmail.com
RTL8821AU and RTL8812AU have to do some things differently, so let
them have full control.
The other chips use the same functions as before.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/98ab839f-9100-44ae-9551-9af743a4aa3a@gmail.com
RTL8821A doesn't have this. Trying to use it results in error messages,
so don't try if ltecoex_addr is NULL.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/d1004817-1760-41d1-9136-3d799757c444@gmail.com
In 'rtw_coex_action_bt_a2dp_pan', 'wl_cpt_test' and 'bt_cpt_test' are
hardcoded to false, so corresponding 'table_case' and 'tdma_case'
assignments are never met.
Also 'rtw_coex_set_rf_para(rtwdev, chip->wl_rf_para_rx[1])' is never
executed. Assuming that CPT was never fully implemented, remove
lookalike leftovers. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 76f631cb40 ("rtw88: coex: update the mechanism for A2DP + PAN")
Signed-off-by: Dmitry Kandybka <d.kandybka@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240809085310.10512-1-d.kandybka@gmail.com
Fix Wi-Fi 2.4Ghz throughput drop over than 40% when Bluetooh is idle.
The code flow will read registers during Wi-Fi power saving, and be
returned, which results in incorrect counters to do mechanism judgment.
Adjust the code flow. Will leave Wi-Fi power save mode first then update
counters.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240320075047.31810-1-pkshih@realtek.com
Use power state to decide whether we can enter or leave IPS accurately,
and then prevent to power on/off twice.
The commit 6bf3a08340 ("wifi: rtw88: add flag check before enter or leave IPS")
would like to prevent this as well, but it still can't entirely handle all
cases. The exception is that WiFi gets connected and does suspend/resume,
it will power on twice and cause it failed to power on after resuming,
like:
rtw_8723de 0000:03:00.0: failed to poll offset=0x6 mask=0x2 value=0x2
rtw_8723de 0000:03:00.0: mac power on failed
rtw_8723de 0000:03:00.0: failed to power on mac
rtw_8723de 0000:03:00.0: leave idle state failed
rtw_8723de 0000:03:00.0: failed to leave ips state
rtw_8723de 0000:03:00.0: failed to leave idle state
rtw_8723de 0000:03:00.0: failed to send h2c command
To fix this, introduce new flag RTW_FLAG_POWERON to reflect power state,
and call rtw_mac_pre_system_cfg() to configure registers properly between
power-off/-on.
Reported-by: Paul Gover <pmw.gover@yahoo.co.uk>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217016
Fixes: 6bf3a08340 ("wifi: rtw88: add flag check before enter or leave IPS")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230216053633.20366-1-pkshih@realtek.com
coex->mutex is used in rtw_coex_info_request() only. Most callers of this
function hold rtwdev->mutex already, except for one callsite in the
debugfs code. The debugfs code alone doesn't justify the extra lock, so
acquire rtwdev->mutex there as well and drop the now unnecessary
spinlock.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202081224.2779981-6-s.hauer@pengutronix.de
Since chip_info has became const table, we must access them via const
pointer to avoid invalid writing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065232.28510-1-pkshih@realtek.com
In order to recognize the gaming controller HID, make a C2H/H2C/Mailbox
handshake to collect all the connected information from BT.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220215004855.4098-6-pkshih@realtek.com
To keep high sensitivity reaction, Bluetooth gaming controller will send
packet very frequently, it will make WLAN performance very poor. To solve
this situation, MIMO PS mechanism makes WLAN/BT own an antenna itself, WLAN
quits 2SS performance but it can get a stable 1SS performance and Bluetooth
gaming controller can keep sensitivity reaction at the same time.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220215004855.4098-5-pkshih@realtek.com
If BT PTA counter can not update regularly, it will lead coex mechanism
run into some unexpected state.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220215004855.4098-4-pkshih@realtek.com
Disable power save TDMA mechanism under HFP COEX, so WLAN can TX/RX full
time.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220215004855.4098-3-pkshih@realtek.com
Fix erroneous code that leads to unreferenced objects. During H2C
operations, some functions returned without freeing the memory that only
the function have access to. Release these objects when they're no longer
needed to avoid potentially memory leaks.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210624023459.10294-1-pkshih@realtek.com
In some funciton, the variable ret just used as return value,and
out label just return ret,so ret and out label are unnecessary,
we should delete these and use return true/false to replace.
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210520005545.31272-1-samirweng1979@163.com
While WL scan, WL is more high priority than BT. The packets from AP
will be a big interference to A2DP. It will lead to A2DP stutters. Stop
answering CTS to AP to decrease AP's packets Tx while WL scan + WL busy.
Enable BT AFH feature to make BT leave away from WL channel.
Desired BT firmware BT-COEX version: 0x1c
Desired WL firmware version: 9.9.x
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210319054218.3319-8-pkshih@realtek.com
Clear WL/BT on/off bit in scoreboard register that is used to exchange
WL/BT status. Since the status is preserved after warm reboot, we must
clear it when WL is going to down.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210219054140.7835-1-pkshih@realtek.com
To protect both of WL/BT performance while BT is under re-link state.
4-slot mode TDMA can make the re-link more sensitive and mitigate the WL
throughput drop.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210112021135.3823-1-pkshih@realtek.com
Currently the variable 'interval' is not initialized and is only set
to 1 when oex_stat->bt_418_hid_existi is true. Fix this by inintializing
variable interval to 0 (which I'm assuming is the intended default).
Addresses-Coverity: ("Uninitalized scalar variable")
Fixes: 5b2e9a35e4 ("rtw88: coex: add feature to enhance HID coexistence performance")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201203175142.1071738-1-colin.king@canonical.com
Add toggle table related function to enhance WL throughput when WL coexist
with 4/18 HID.
The toggle table feature will toggle WL/BT priority table during WL slot,
it can decrease the impact from HID's frequently packets and prevent HID
lag.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-11-pkshih@realtek.com
Add modifications for A2DP interoperability issue of TWS earphones.
Some TWS earphones has low buffer size, so it's necessary to reduce
the slot period to let it get data more frequently.
(e.g. use 4-slot to replace the original 2-slot method).
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-10-pkshih@realtek.com
The original setting misses some necessary configuration.
Make coexistence slot align to beacon and check the connection situation
to know if we need to extend WLAN slot or not.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-9-pkshih@realtek.com
Some AP will not follow the power save request, or it cannot stop
transmission until its queue is empty. It may bring the decreasing of
data rate.
WLAN firmware will count is the AP still leaked packet after power save
handshake was done or not to enable WLAN slot extend mechanism.
The extend WLAN slot mechanism will extend the WLAN slot after power save
handshake, 5 ms per times, maximum is 5 times to received the leaked packet
to avoid the rate lower down.
And if the transmission was already locked at CCK rate.
The extended WLAN slot can also increase the opportunity that we can
received the CCK's long packet and be released from CCK rate.
While BT multi-link status was finished, there is possible that it still
has some packet remained for seconds. Add a timer to remain the multi-link
mechanism to protect WLAN Rx.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-8-pkshih@realtek.com
Add a flag to make decision whether the mechanism
should go into free-run mode or not.
For now, it is always false, the flag assignment will
be implemented later.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-7-pkshih@realtek.com
Add TDMA slot type setting for later usage.
Since the transmission of HID profile is very frequently,
it may bring a big impact to WLAN performance.
To change slot type, it can make mechanism be more flexible.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-6-pkshih@realtek.com
In free run mode, this WLAN info updating is only related to AFH
information, not related to the connection state, which is the current
implementation.
Always update WLAN info in free run mode now.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-5-pkshih@realtek.com
Update A2DP+PAN+WL mechanism for CPT(Coexistence Performance Test) to
enhance WL/BT performance at the environment that some specific AP are
existing.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-4-pkshih@realtek.com
Add message for debugging usage and the program flow is no change.
Add a variable reserved for WLAN firmware synchronize.
Add a group of variable to save BT packet counter, it will be
assigned as mechanism judgment in the future. Now it is just for
debug usage.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-3-pkshih@realtek.com
When WLAN entering or leaving, it's necessary to run coexistence mechanism
to ensure the setting matched current status.
Without calling rtw_coex_run_coex(), WLAN poor throughput or bad A2DP
quality may happen.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-2-pkshih@realtek.com
Fix sometimes FW information will be parsed as wrong value,
do a correction of sign bit to show the correct information.
(Ex, Value should be 20, but it shows 236.)
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-12-pkshih@realtek.com
Remove extend 5 ms related operation at WLAN media status notify.
The mechanism should be enable only while DUT connect to a AP that it
doesn't follow our power save control or its rate is decreasing unusually
sensitive. So we extend a extra slot to save the transmission rate.
The original logic will always extend WLAN slot.
It will lead to BT slot always decrease 5 ms.
Remove write scoreboard action at WLAN media status notify.
It has already done in WLAN info notify.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-11-pkshih@realtek.com
Remove some action which were writing scan bit to scoreboard,
since these behaviors are redundant.
It is already done in WLAN info notify.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-10-pkshih@realtek.com
Force set the coexistence to BT high priority during
WLAN initial/power-on step. Since the duration the related setting
may be not ready yet.
The score board is not related to scan when initialing, remove the scan
parameter.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-9-pkshih@realtek.com
While the mechanism goes to 2G_free_run or WL5G_BT2G,
set BT to hardware PTA mode to get a more efficiently performance.
Add a flag to indicate antenna switch is supported or not so
that the IC serials which has different antenna structure can
set antenna correctly.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-8-pkshih@realtek.com
The updated parameter and original parameter all means TDMA-OFF.
The original setting write 0x8 to firmware, but it only works for
some old IC series.
To avoid the confusing, update a proper parameter.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-7-pkshih@realtek.com
Add the related coexistence mechanism about RF4CE and WLAN connected
flag to decide control packet is whether higher or normal priority.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-6-pkshih@realtek.com
Because sometimes hardware action may be unpredictable.
(Ex: after WLAN LPS...etc)
Add a check mechanism if the action is triggered by
some concerned case, it can force to write the table again.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-5-pkshih@realtek.com
When WLAN in critical procedure, such as connecting, scan and so on,
coexistence will notify BT by scoreboard.
While BT firmware received the scoreboard interrupt, it will adjust
BT page priority lower to avoid WLAN critical procedure suffering impact.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-4-pkshih@realtek.com
Because the WLAN RSSI report feature had been implemented at WLAN link info
update function, it is redundant to update WLAN RSSI while BT is updating
link info, so remove the update WLAN RSSI part.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-3-pkshih@realtek.com
Add considering for different WLAN beacon interval in coexistence
mechanism.
Because the WLAN beacon period may be not 100 ms, so it's necessary
to consider any beacon period and set timer according to the interval.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-2-pkshih@realtek.com
Life time related setting is related to WLAN active port number,
not its mode. The original setting may cause poor WLAN performance.
In most case, WLAN TX limitation is helpful for BT in coexistence
scenario, especially for A2DP quality.
So this is necessary to fix the setting and constraint it.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-12-pkshih@realtek.com
Since coexistence issue is related to WL/BT and each digital/analog/rf,
and these issues are often critical with low failure rate, add more
debugging information is helpful to clarify issues.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-11-pkshih@realtek.com
The original mechanism may cause A2DP glitch during WiFi connecting AP.
Because the original TDMA may decrease too much A2DP slot.
This patch add a timer and variable to let the case A2DP + WL_Connecting
performed more well.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-9-pkshih@realtek.com
Add counter to count BT info C2H command for debug usage.
It could present the C2H channel situation.
Fix BT IQK state decision condition for counting.
The original condition is wrong, it would cause coexistence mechanism
going to the wrong strategy.
New format supports getting TDMA parameter from WL firmware, since
coexistence needs current TDMA parameter to decide strategy.
Remove unnecessary operations about scoreboard, it is not a must for
current version.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-8-pkshih@realtek.com
The original stop_dm flag is shared with the wifi and coexistence
mechanism internal usage, which represent two meanings, and makes
developers hard to debug.
Add a new flag manual_control for coexistence mechanism usage only.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-7-pkshih@realtek.com
To make sure the related ANT/RF_PARA setting will be expected result in COEX.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-6-pkshih@realtek.com
Adjust space and comments, and fix "line over 80 characters" warnings
reported by checkpatch.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-5-pkshih@realtek.com
Use macro definition to replace magic number.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-4-pkshih@realtek.com
